ENTERASYS-MULTI-AUTH-MIB

File: ENTERASYS-MULTI-AUTH-MIB.mib (63025 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB ENTITY-MIB INET-ADDRESS-MIB
ENTERASYS-UPN-TC-MIB P-BRIDGE-MIB ENTERASYS-MIB-NAMES

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Unsigned32 Integer32 Gauge32
TEXTUAL-CONVENTION TruthValue TimeStamp
DateAndTime MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP ifIndex entPhysicalIndex
InetAddressType InetAddress StationAddressType
StationAddress EnabledStatus etsysModules

Defined Types

EtsysMultiAuthTypes  
This convention enumerates the authentication types supported by Enterasys Networks' devices.
TEXTUAL-CONVENTION    
  INTEGER ieee8021x(1), pwa(2), macAuth(3), cep(4), radiusSnooping(5)  

EtsysMultiAuthTypePrecedence  
The precedence by which authentication results will be applied to network traffic. This object will have a maximum size equal to the number of enumerations specified by the EtsysMultiAuthTypes textual convention. Each octet in this object represents a specific authentication type. The first octet contains the authentication type with the highest precedence, the second octet contains the type of the next highest precedence, and so forth. For example, a precedence from highest to lowest of ieee8021x(1), macAuth(3), pwa(2), cep(4), radiusSnooping(5) would be represented as '0103020405'H.
TEXTUAL-CONVENTION    
  OCTET STRING Size(0..32)  

EtsysMultiAuthStatus  
The status of authentication for this session. A value of authSuccess(1) means authentication was attempted and succeeded. A value of authFailed(2) means authentication was attempted and failed for a reason other than communication timing out with the authorization server. A value of authInProgress(3) means that the authorization process has been started but has not completed yet. A value of authServerTimeout(4) means that the request to the authorization server for this session timed out without a reply from the server. A value of authTerminated(5) indicates that the session was active or in progress and was subsequently terminated. A session may be terminated for several reasons, including but not limited to, session timeout, idle timeout, the ifOperStatus of the interface on which the session was authenticated transitioning out of the up(1) state, or explicit administrative management action.
TEXTUAL-CONVENTION    
  INTEGER authSuccess(1), authFailed(2), authInProgress(3), authServerTimeout(4), authTerminated(5)  

EtsysMultiAuthTypePropertiesEntry  
SEQUENCE    
  etsysMultiAuthType EtsysMultiAuthTypes
  etsysMultiAuthSessionTimeout Unsigned32
  etsysMultiAuthIdleTimeout Unsigned32
  etsysMultiAuthCurrentNumUsers Gauge32

EtsysMultiAuthPortEntry  
SEQUENCE    
  etsysMultiAuthPortMode INTEGER
  etsysMultiAuthPortMaxNumUsers Unsigned32
  etsysMultiAuthPortNumUsersAllowed Unsigned32
  etsysMultiAuthPortCurrentNumUsers Gauge32
  etsysMultiAuthPortClearUsers TruthValue
  etsysMultiAuthPortTrapEnable BITS

EtsysMultiAuthPortTypeEntry  
SEQUENCE    
  etsysMultiAuthPortTypeCurrentNumUsers Gauge32

EtsysMultiAuthStationEntry  
SEQUENCE    
  etsysMultiAuthStationAddrType StationAddressType
  etsysMultiAuthStationAddr StationAddress
  etsysMultiAuthStationClearUsers TruthValue

EtsysMultiAuthSessionStationEntry  
SEQUENCE    
  etsysMultiAuthSessionAgentType EtsysMultiAuthTypes
  etsysMultiAuthSessionStationAuthStatus EtsysMultiAuthStatus
  etsysMultiAuthSessionAuthAttemptTime TimeStamp
  etsysMultiAuthSessionAuthServerType INTEGER
  etsysMultiAuthSessionAuthServerAddrType InetAddressType
  etsysMultiAuthSessionAuthServerAddr InetAddress
  etsysMultiAuthSessionPolicyIndex Integer32
  etsysMultiAuthSessionIsApplied TruthValue
  etsysMultiAuthSessionTerminationTime DateAndTime
  etsysMultiAuthSessionSessionTimeout Unsigned32
  etsysMultiAuthSessionIdleTimeout Unsigned32
  etsysMultiAuthSessionDuration Gauge32
  etsysMultiAuthSessionIdleTime Gauge32
  etsysMultiAuthSessionVlanTunnelAttribute Integer32

EtsysMultiAuthSessionPortEntry  
SEQUENCE    
  etsysMultiAuthSessionPortAuthStatus EtsysMultiAuthStatus

EtsysMultiAuthModuleEntry  
SEQUENCE    
  etsysMultiAuthModuleMaxNumUsers Unsigned32
  etsysMultiAuthModuleCurrentNumUsers Gauge32

Defined Values

etsysMultiAuthMIB 1.3.6.1.4.1.5624.1.2.46
This MIB module defines a portion of the SNMP MIB under the Enterasys Networks enterprise OID pertaining to configuration of multiple authentication mechanisms to be run simultaneously on a device.
MODULE-IDENTITY    

etsysMultiAuthObjects 1.3.6.1.4.1.5624.1.2.46.1
OBJECT IDENTIFIER    

etsysMultiAuthSystem 1.3.6.1.4.1.5624.1.2.46.1.1
OBJECT IDENTIFIER    

etsysMultiAuthPort 1.3.6.1.4.1.5624.1.2.46.1.2
OBJECT IDENTIFIER    

etsysMultiAuthStation 1.3.6.1.4.1.5624.1.2.46.1.3
OBJECT IDENTIFIER    

etsysMultiAuthSession 1.3.6.1.4.1.5624.1.2.46.1.4
OBJECT IDENTIFIER    

etsysMultiAuthModule 1.3.6.1.4.1.5624.1.2.46.1.5
OBJECT IDENTIFIER    

etsysMultiAuthNotification 1.3.6.1.4.1.5624.1.2.46.1.0
OBJECT IDENTIFIER    

etsysMultiAuthSystemSupportedTypes 1.3.6.1.4.1.5624.1.2.46.1.1.1
This object specifies that authentication types that the device supports. A bit will be set for each corresponding type that is supported.
Status: current Access: read-only
OBJECT-TYPE    
  BITS ieee8021x(0), pwa(1), macAuth(2), cep(3), radiusSnooping(4)  

etsysMultiAuthSystemMaxNumUsers 1.3.6.1.4.1.5624.1.2.46.1.1.2
The maximum number of users the can be actively authenticated or have authentications in progress at one time in the system.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

etsysMultiAuthSystemCurrentNumUsers 1.3.6.1.4.1.5624.1.2.46.1.1.3
The current number of users the are actively authenticated, have authentications in progress, or the device is keeping authentication termination information for in the system.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

etsysMultiAuthSystemMode 1.3.6.1.4.1.5624.1.2.46.1.1.4
The value strictIeee8021x(1) will cause the device to authenticate in strict adherence to IEEE Std. 802.1X-2001. In this mode no other authentication mechanisms will be active. While in this mode, changes may be made to other objects in the MIB, but they will have no effect on the operation of the device until such time as the system mode is changed to etsysMultiAuth(2). A set of this object to a value of etsysMultiAuth(2) will cause the device to authenticate using multiple authenticators simultaneously.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER strictIeee8021x(1), etsysMultiAuth(2)  

etsysMultiAuthSystemDefaultPrecedence 1.3.6.1.4.1.5624.1.2.46.1.1.5
The precedence that authentication results will be applied to network traffic by default. This object will have a size equal to the number of enumerations specified by the EtsysMultiAuthTypes textual convention.
Status: current Access: read-only
OBJECT-TYPE    
  EtsysMultiAuthTypePrecedence  

etsysMultiAuthSystemAdminPrecedence 1.3.6.1.4.1.5624.1.2.46.1.1.6
This object allows one to modify the default precedence by which authentication results will be applied to network traffic. Sets to this object are not required to specify all of the types that the device supports. If less types are specified than are supported, then all types that were not specified will be given an operational precedence based on that type's default precedence relative to the last type specified. For example, if the default precedence is '030102'H and the object is set to '02'H then operational precedence would be '020301'H. A set to this object of a zero length octet string will clear the administrative precedence. In this case the operational precedence would be equal to the default precedence.
Status: current Access: read-write
OBJECT-TYPE    
  EtsysMultiAuthTypePrecedence  

etsysMultiAuthSystemOperPrecedence 1.3.6.1.4.1.5624.1.2.46.1.1.7
This object returns the operational precedence of authentication types as they will be applied to network traffic. The value returned by this object is the calculated result of the etsysMultiAuthSystemDefaultPrecedence and etsysMultiAuthSystemAdminPrecedence objects. This object will have a size equal to the number of enumerations specified by the EtsysMultiAuthTypes textual convention.
Status: current Access: read-only
OBJECT-TYPE    
  EtsysMultiAuthTypePrecedence  

etsysMultiAuthTypePropertiesTable 1.3.6.1.4.1.5624.1.2.46.1.1.8
A table of properties per authentication type.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysMultiAuthTypePropertiesEntry

etsysMultiAuthTypePropertiesEntry 1.3.6.1.4.1.5624.1.2.46.1.1.8.1
An entry containing per authentication type properties.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysMultiAuthTypePropertiesEntry  

etsysMultiAuthType 1.3.6.1.4.1.5624.1.2.46.1.1.8.1.1
The authentication type the entry properties pertain to.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  EtsysMultiAuthTypes  

etsysMultiAuthSessionTimeout 1.3.6.1.4.1.5624.1.2.46.1.1.8.1.2
The maximum number of seconds an authenticated session may last before termination of the session. A value of zero indicates that no session timeout will be applied. This value MAY be superseded by a session timeout value provided by the authenticating server. For example, if a session is authenticated by a RADIUS server, that server may encode a Session-Timeout Attribute in its authentication response. The operational timeout value of a given authenticated session is specified by the etsysMultiAuthSessionSessionTimeout object.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..65535  

etsysMultiAuthIdleTimeout 1.3.6.1.4.1.5624.1.2.46.1.1.8.1.3
The maximum number of consecutive seconds an authenticated session may be idle before termination of the session. A value of zero indicates that no idle timeout will be applied. This value MAY be superseded by a idle timeout value provided by the authenticating server. For example, if a session is authenticated by a RADIUS server, that server may encode a Idle-Timeout Attribute in its authentication response. The operational idle timeout value of a given authenticated session is specified by the etsysMultiAuthSessionIdleTimeout object.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..65535  

etsysMultiAuthCurrentNumUsers 1.3.6.1.4.1.5624.1.2.46.1.1.8.1.4
The current number of users the are actively authenticated or have authentications in progress for this authentication type in the system.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

etsysMultiAuthSystemMaxNumUsersReachedTrapEnable 1.3.6.1.4.1.5624.1.2.46.1.1.9
This object allows for the enabling or disabling the transmission of the etsysMultiAuthSystemMaxNumUsersReached NOTIFICATION.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

etsysMultiAuthPortTable 1.3.6.1.4.1.5624.1.2.46.1.2.1
A table of per port information and configuration for user authentication.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysMultiAuthPortEntry

etsysMultiAuthPortEntry 1.3.6.1.4.1.5624.1.2.46.1.2.1.1
An entry containing per port authentication data. Only interfaces that are able to authenticate users are represented in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysMultiAuthPortEntry  

etsysMultiAuthPortMode 1.3.6.1.4.1.5624.1.2.46.1.2.1.1.1
This object specifies the authorization mode to use for packets received on this interface. A value of forceUnauthorized(1) indicates that the interface is always unauthenticated. A value of forceAuthorized(2) indicates that users on this port will always be considered to be authenticated. A value of authOptional(3) indicates that authentication is optional on this interface. Packets received from unauthenticated users on the interface will be processed using the static configuration of the interface. Users may promote the policy applied to their traffic by actively authenticating on this interface. A value of authRequired(4) indicates that all packets received on the interface will be dropped until authentication succeeds. Some authentication types, such as PWA, will not be fully functional in this mode of operation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forceUnauthorized(1), forceAuthorized(2), authOptional(3), authRequired(4)  

etsysMultiAuthPortMaxNumUsers 1.3.6.1.4.1.5624.1.2.46.1.2.1.1.2
The maximum number of users that can be actively authenticated or have authentications in progress at one time on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

etsysMultiAuthPortNumUsersAllowed 1.3.6.1.4.1.5624.1.2.46.1.2.1.1.3
The user configured number of users that can be actively authenticated or have authentications in progress at one time on this interface. This object has a default value equal to the value of etsysMultiAuthPortMaxNumUsers for this interface. If the value set to this object is less than its current value, it will have the same effect as setting the etsysMultiAuthPortClearUsers object to a value of true(1).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

etsysMultiAuthPortCurrentNumUsers 1.3.6.1.4.1.5624.1.2.46.1.2.1.1.4
The current number of users that are actively authenticated or have authentications in progress at one time on this interface. By definition this value can not exceed the value specified by etsysMultiAuthPortMaxNumUsers for the same interface.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

etsysMultiAuthPortClearUsers 1.3.6.1.4.1.5624.1.2.46.1.2.1.1.5
Setting this object to a value of true(1) will cause all users that are currently authenticated or that have authentications in progress on this interface to become unauthenticated. This will cause any such entries with matching ifIndex values in the etsysMultiAuthSessionStationTable tables to change their authorization status to authTerminated(5). Setting this object to a value of false(2) has no effect. This object will always return a value of false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

etsysMultiAuthPortTrapEnable 1.3.6.1.4.1.5624.1.2.46.1.2.1.1.6
This object allows for the enabling or disabling of each trap on a per interface basis. Setting a given bit to a value of 1 allows traps of that type to be sent for events on that interface. Setting a given bit to a value of 0 disallows traps of that type to be sent for events on that interface. The individual bits correlate to specific traps as follows: BIT NOTIFICATION ---------------------------------------------------------------- authSuccessTrap(0) etsysMultiAuthSuccess authFailedTrap(1) etsysMultiAuthFailed authTerminatedTrap(2) etsysMultiAuthTerminated maxNumUsersReachedTrap(3) etsysMultiAuthMaxNumUsersReached
Status: current Access: read-write
OBJECT-TYPE    
  BITS authSuccessTrap(0), authFailedTrap(1), authTerminatedTrap(2), maxNumUsersReachedTrap(3)  

etsysMultiAuthPortTypeTable 1.3.6.1.4.1.5624.1.2.46.1.2.2
A table of per port, per authentication type information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysMultiAuthPortTypeEntry

etsysMultiAuthPortTypeEntry 1.3.6.1.4.1.5624.1.2.46.1.2.2.1
An entry containing per port, per authentication type data. Only interfaces that are able to authenticate users are represented in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysMultiAuthPortTypeEntry  

etsysMultiAuthPortTypeCurrentNumUsers 1.3.6.1.4.1.5624.1.2.46.1.2.2.1.1
The current number of users the are actively authenticated or have authentications in progress for this authentication type on the specified port.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

etsysMultiAuthStationTable 1.3.6.1.4.1.5624.1.2.46.1.3.1
A table of station configuration on specific interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysMultiAuthStationEntry

etsysMultiAuthStationEntry 1.3.6.1.4.1.5624.1.2.46.1.3.1.1
An entry containing authentication information on a per station, per port basis. Only interfaces that are able to authenticate users are represented in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysMultiAuthStationEntry  

etsysMultiAuthStationAddrType 1.3.6.1.4.1.5624.1.2.46.1.3.1.1.1
The type of station represented by etsysMultiAuthStationAddr.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  StationAddressType  

etsysMultiAuthStationAddr 1.3.6.1.4.1.5624.1.2.46.1.3.1.1.2
The station address for the authenticated user.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  StationAddress  

etsysMultiAuthStationClearUsers 1.3.6.1.4.1.5624.1.2.46.1.3.1.1.3
Setting this object to a value of true(1) will cause any users with the specified station address that are currently authenticated or that have authentications in progress to become unauthenticated. This will cause any entries with matching etsysMultiAuthStationAddr values in the etsysMultiAuthSessionStationTable tables to change their authorization status to authTerminated(5). Setting this object to a value of false(2) has no effect. This object will always return a value of false(2).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

etsysMultiAuthSessionStationTable 1.3.6.1.4.1.5624.1.2.46.1.4.1
A table of session information and configuration for user authentication. Entries in this table represent users in various stages of authentication. Entries that do not have a etsysMultiAuthSessionStationAuthStatus value of authSuccess(1) or authInProgress(3) MAY be removed by the agent as required in order to free resources for new user authentications.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysMultiAuthSessionStationEntry

etsysMultiAuthSessionStationEntry 1.3.6.1.4.1.5624.1.2.46.1.4.1.1
An entry containing authentication information on a per station, per port, per authentication agent type basis. Only interfaces that are able to authenticate users are represented in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysMultiAuthSessionStationEntry  

etsysMultiAuthSessionAgentType 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.1
The type of authentication agent for this session.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  EtsysMultiAuthTypes  

etsysMultiAuthSessionStationAuthStatus 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.2
The status of authentication for this session.
Status: current Access: read-only
OBJECT-TYPE    
  EtsysMultiAuthStatus  

etsysMultiAuthSessionAuthAttemptTime 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.3
The value of sysUpTime when this session last attempted authorization. For entries that have a value of authInProgress(3) for etsysMultiAuthSessionStationAuthStatus this object MAY return a value of zero.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

etsysMultiAuthSessionAuthServerType 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.4
The type of authentication server used to authenticate this session. A value of radius(1) indicates that a RADIUS request and response were attempted in order to authenticate the session. A value of local(2) indicates that the session was authenticated by a local file or configuration on the device itself.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER radius(1), local(2)  

etsysMultiAuthSessionAuthServerAddrType 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.5
The type of data returned by etsysMultiAuthSessionAuthServerAddr. If the etsysMultiAuthSessionAuthServerType leaf for this entry has a value of local(2) then this object MUST return a a value of unknown(0).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

etsysMultiAuthSessionAuthServerAddr 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.6
The network address of the authentication server for this session. If the etsysMultiAuthSessionAuthServerType leaf for this entry has a value of local(2) then this object MUST return a zero length string.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

etsysMultiAuthSessionPolicyIndex 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.7
The Policy Profile Index returned from the authentication server for this session. The value of zero indicates that no policy will be applied for this session. If the etsysMultiAuthSessionStationAuthStatus object returns a value of authSuccess(1), then a value of zero is the result of the policy not being configured on the authorization server. For all other values of etsysMultiAuthSessionStationAuthStatus a value of zero for this object is the result of authorization not succeeding or not having completed. All values other than zero are valid Policy Profile Indexes that specify the policy profile the user will receive on this interface. If a given user has been authenticated by multiple authentication types on the same interface the policy that is applied to the user's packets is determined by the precedence of the agents as specified by etsysMultiAuthSystemOperPrecedence. These indexes are suitable for indexing in the ENTERASYS-POLICY-PROFILE-MIB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 1..65535  

etsysMultiAuthSessionIsApplied 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.8
This object indicates whether this entry and the policy index contained within it are actively being applied to traffic matching the interface and station address of this entry. A value of true(1) indicates that this entry is being applied. A value of false(2) indicates that the entry is not being applied. Only one authentication type per interface station address ordered pair may be applied at a single time. The operational precedence of the various authentication types determines which if any type will be applied.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

etsysMultiAuthSessionTerminationTime 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.9
The local date and time that the session was terminated. If the session is not in the authTerminated(5) state this object MUST return '00000000'H.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime Size(8)  

etsysMultiAuthSessionSessionTimeout 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.10
The maximum number of seconds this session may last before automatic termination. A value of zero indicates that no session timeout will be applied. This value MAY be provided by the etsysMultiAuthSessionTimeout object or by the authenticating server.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 1..65535  

etsysMultiAuthSessionIdleTimeout 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.11
The maximum number of consecutive seconds this session may be idle before automatic termination. A value of zero indicates that no idle timeout will be applied. This value MAY be provided by the etsysMultiAuthIdleTimeout object or by the authenticating server.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0 | 1..65535  

etsysMultiAuthSessionDuration 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.12
The length of this session in seconds. This object MAY return zero for a session in any state other than authSuccess(1).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

etsysMultiAuthSessionIdleTime 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.13
The number of consecutive seconds this session has been idle. This object MAY return zero for a session in any state other than authSuccess(1).
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

etsysMultiAuthSessionVlanTunnelAttribute 1.3.6.1.4.1.5624.1.2.46.1.4.1.1.14
The VLAN Tunnel Attribute (Tunnel-Group-ID) returned from the authentication server for this session. This value is interpreted as the 12 bit VLAN identifier to be applied to traffic from the session entity. Policy VLAN classification rules have precedence in assigning VLAN, however, in the absence of any applicable rules, this VLAN will be used. If the traffic is already tagged, this VLAN will only be applied if TCI overwrite has been enabled (through Policy or ctDot1qPortReplaceTCI). A value of zero indicates that there is no authenticated VLAN ID for the given session (none was provided by the authentication server). Should a session become unauthenticated this value MUST return zero. A value of 4095 indicates that a the session has been authenticated, but that the VLAN returned could not be applied to the port (possibly because of resource constraints or misconfiguration). The traffic from the session entity will be assigned VLAN through Policy or standard 802.1Q mechanisms.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 1..4094 | 4095  

etsysMultiAuthSessionPortTable 1.3.6.1.4.1.5624.1.2.46.1.4.2
A table of session information and configuration for user authentication. This table represents the information specified in the etsysMultiAuthSessionStationTable with alternate indexing for faster lookups of data on per port basis.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysMultiAuthSessionPortEntry

etsysMultiAuthSessionPortEntry 1.3.6.1.4.1.5624.1.2.46.1.4.2.1
An entry containing authentication information on a per port, per station, per authentication agent type basis. Only interfaces that are able to authenticate users are represented in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysMultiAuthSessionPortEntry  

etsysMultiAuthSessionPortAuthStatus 1.3.6.1.4.1.5624.1.2.46.1.4.2.1.1
The status of authentication for this session.
Status: current Access: read-only
OBJECT-TYPE    
  EtsysMultiAuthStatus  

etsysMultiAuthModuleTable 1.3.6.1.4.1.5624.1.2.46.1.5.1
A table of per module information for user authentication.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EtsysMultiAuthModuleEntry

etsysMultiAuthModuleEntry 1.3.6.1.4.1.5624.1.2.46.1.5.1.1
An entry containing per module authentication data. Only physical indexes with a entPhysicalClass of module(9) are represented in this table. Furthermore, each entity represented in this table must have authentication resources that are separate from every other entity in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  EtsysMultiAuthModuleEntry  

etsysMultiAuthModuleMaxNumUsers 1.3.6.1.4.1.5624.1.2.46.1.5.1.1.1
The maximum number of users that can be actively authenticated or have authentications in progress at one time on the specified module.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

etsysMultiAuthModuleCurrentNumUsers 1.3.6.1.4.1.5624.1.2.46.1.5.1.1.2
The current number of users that are actively authenticated or have authentications in progress at one time on the specified module. By definition this value can not exceed the value specified by etsysMultiAuthModuleMaxNumUsers for the same module.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

etsysMultiAuthModuleMaxNumUsersReachedTrapEnable 1.3.6.1.4.1.5624.1.2.46.1.5.2
This object allows for the enabling or disabling the transmission of the etsysMultiAuthModuleMaxNumUsersReached NOTIFICATION.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

etsysMultiAuthSuccess 1.3.6.1.4.1.5624.1.2.46.1.0.1
An etsysMultiAuthSuccess trap signifies that the SNMP entity, acting in an agent role, has successfully authenticated a station on one of its interfaces. The included objects of etsysMultiAuthStationAddrType and etsysMultiAuthStationAddr uniquely identify the station that has been authenticated. The interface that the station was authenticated on is specified by the ifIndex object, and the type of authentication used is to authenticate the station is specified by the etsysMultiAuthSessionAgentType object. This trap will only be generated on interfaces that are in the authOptional(3) or authRequired(4) state.
Status: current Access: read-write
NOTIFICATION-TYPE    

etsysMultiAuthFailed 1.3.6.1.4.1.5624.1.2.46.1.0.2
An etsysMultiAuthFailed trap signifies that the SNMP entity, acting in an agent role, has identified a station that attempted and subsequently failed to authenticate on one of its interfaces. The included objects of etsysMultiAuthStationAddrType and etsysMultiAuthStationAddr uniquely identify the station that attempted to authenticate. The interface that the station attempted to authenticate on is specified by the ifIndex object, and the type of authentication attempted is specified by the etsysMultiAuthSessionAgentType object. This trap will only be generated on interfaces that are in the authOptional(3) or authRequired(4) state.
Status: current Access: read-write
NOTIFICATION-TYPE    

etsysMultiAuthTerminated 1.3.6.1.4.1.5624.1.2.46.1.0.3
An etsysMultiAuthTerminated trap signifies that the SNMP entity, acting in an agent role, has terminated the authentication of a station on one of its interfaces. The included objects of etsysMultiAuthStationAddrType and etsysMultiAuthStationAddr uniquely identify the station for which authentication was terminated. The interface that the station was previously authenticated on is specified by the ifIndex object, and the type of authentication that the station was terminated for is specified by the etsysMultiAuthSessionAgentType object. This trap will only be generated on interfaces that are in the authOptional(3) or authRequired(4) state.
Status: current Access: read-write
NOTIFICATION-TYPE    

etsysMultiAuthMaxNumUsersReached 1.3.6.1.4.1.5624.1.2.46.1.0.4
An etsysMultiAuthMaxNumUsersReached trap signifies that the SNMP entity, acting in an agent role, has an interface where subsequent to a successful authentication, the number of current sessions on the interface equals the maximum number of sessions allowed for that interface. The interface that the maximum number of sessions has been reached is specified by the ifIndex object.
Status: current Access: read-write
NOTIFICATION-TYPE    

etsysMultiAuthModuleMaxNumUsersReached 1.3.6.1.4.1.5624.1.2.46.1.0.5
An etsysMultiAuthModuleMaxNumUsersReached trap signifies that the SNMP entity, acting in an agent role, has a module where subsequent to a successful authentication, the number of current sessions on the module equals the maximum number of sessions allowed for that module. The module that the maximum number of sessions has been reached is specified by the entPhysicalIndex object.
Status: current Access: read-write
NOTIFICATION-TYPE    

etsysMultiAuthSystemMaxNumUsersReached 1.3.6.1.4.1.5624.1.2.46.1.0.6
An etsysMultiAuthSystemMaxNumUsersReached trap signifies that the SNMP entity, acting in an agent role, where subsequent to a successful authentication, has the number of current sessions on the system equals the maximum number of sessions allowed for that system, .
Status: current Access: read-write
NOTIFICATION-TYPE    

etsysMultiAuthConformance 1.3.6.1.4.1.5624.1.2.46.2
OBJECT IDENTIFIER    

etsysMultiAuthGroups 1.3.6.1.4.1.5624.1.2.46.2.1
OBJECT IDENTIFIER    

etsysMultiAuthCompliances 1.3.6.1.4.1.5624.1.2.46.2.2
OBJECT IDENTIFIER    

etsysMultiAuthSystemGroup 1.3.6.1.4.1.5624.1.2.46.2.1.1
The system group for all devices supporting Multiple Authentication.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthPortBaseGroup 1.3.6.1.4.1.5624.1.2.46.2.1.2
The base level port group for all devices supporting Multiple Authentication.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthPortTrapGroup 1.3.6.1.4.1.5624.1.2.46.2.1.3
This group of objects for all devices supporting per interface SNMP notifications.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthStationGroup 1.3.6.1.4.1.5624.1.2.46.2.1.4
The station group for all devices supporting Multiple Authentication.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthSessionGroup 1.3.6.1.4.1.5624.1.2.46.2.1.5
The session group for all devices supporting Multiple Authentication.
Status: deprecated Access: read-write
OBJECT-GROUP    

etsysMultiAuthNotificationPortGroup 1.3.6.1.4.1.5624.1.2.46.2.1.6
The group of per interface notifications for Multiple Authentication.
Status: current Access: read-write
NOTIFICATION-GROUP    

etsysMultiAuthModuleGroup 1.3.6.1.4.1.5624.1.2.46.2.1.7
The module group for all devices supporting Multiple Authentication.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthSessionGroup2 1.3.6.1.4.1.5624.1.2.46.2.1.8
The session group for all devices supporting Multiple Authentication.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthTimeoutGroup 1.3.6.1.4.1.5624.1.2.46.2.1.9
The group of objects for all devices that support timing out Multiple Authentication sessions.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthCurrentNumUsersGroup 1.3.6.1.4.1.5624.1.2.46.2.1.10
The group of objects for all devices that support counting the number of current users on a per authentication type basis.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthModuleTrapGroup 1.3.6.1.4.1.5624.1.2.46.2.1.11
The group of objects for all devices supporting module SNMP notifications.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthSystemTrapGroup 1.3.6.1.4.1.5624.1.2.46.2.1.12
The group of objects for all devices supporting system SNMP notifications.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthNotificationModuleGroup 1.3.6.1.4.1.5624.1.2.46.2.1.13
The group of per module notifications for Multiple Authentication.
Status: current Access: read-write
NOTIFICATION-GROUP    

etsysMultiAuthNotificationSystemGroup 1.3.6.1.4.1.5624.1.2.46.2.1.14
The group of per system notifications for Multiple Authentication.
Status: current Access: read-write
NOTIFICATION-GROUP    

etsysMultiAuthTunnelAttributeGroup 1.3.6.1.4.1.5624.1.2.46.2.1.15
The group of objects for all devices supporting 802.1X RADIUS tunnel attributes for 802.1Q VLANs.
Status: current Access: read-write
OBJECT-GROUP    

etsysMultiAuthCompliance 1.3.6.1.4.1.5624.1.2.46.2.2.1
This compliance statement has been deprecated in favor of the expanded group defined by etsysMultiAuthCompliance2.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

etsysMultiAuthCompliance2 1.3.6.1.4.1.5624.1.2.46.2.2.2
This compliance statement has been deprecated in favor of the expanded group defined by etsysMultiAuthCompliance3.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

etsysMultiAuthCompliance3 1.3.6.1.4.1.5624.1.2.46.2.2.3
This compliance statement has been deprecated in favor of the expanded group defined by etsysMultiAuthCompliance4.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

etsysMultiAuthTimeoutCompliance 1.3.6.1.4.1.5624.1.2.46.2.2.4
The compliance statement for devices that support timing out of Multiple Authentication sessions.
Status: current Access: read-only
MODULE-COMPLIANCE    

etsysMultiAuthCurrentNumUserCompliance 1.3.6.1.4.1.5624.1.2.46.2.2.5
The compliance statement for all devices that support counting the number of current users on a per authentication type basis.
Status: current Access: read-only
MODULE-COMPLIANCE    

etsysMultiAuthCompliance4 1.3.6.1.4.1.5624.1.2.46.2.2.6
The compliance statement for devices that support Multiple Authentication.
Status: current Access: read-only
MODULE-COMPLIANCE    

etsysMultiTunnelAttributeCompliance 1.3.6.1.4.1.5624.1.2.46.2.2.7
The compliance statement for all devices that support 802.1X RADIUS Tunnel Attributes.
Status: current Access: read-only
MODULE-COMPLIANCE