Dell-Vendor-MIB

File: Dell-Vendor-MIB.mib (21166 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI SNMPv2-TC

Imported symbols

enterprises TimeTicks MODULE-IDENTITY
OBJECT-TYPE Unsigned32 Integer32
IpAddress NOTIFICATION-TYPE DisplayString
RowStatus DateAndTime TEXTUAL-CONVENTION

Defined Types

EnvMonState  
Represents the state of a device being monitored. Valid values are: normal(1): the environment is good, such as low temperature. warning(2): the environment is bad, such as temperature above normal operation range but not too high. critical(3): the environment is very bad, such as temperature much higher than normal operation limit. shutdown(4): the environment is the worst, the system should be shutdown immediately. notPresent(5): the environmental monitor is not present, such as temperature sensors do not exist. notFunctioning(6): the environmental monitor does not function properly, such as a temperature sensor generates a abnormal data like 1000 C.
TEXTUAL-CONVENTION    
  INTEGER normal(1), warning(2), critical(3), shutdown(4), notPresent(5), notFunctioning(6)  

ProductIdentificationPerBoxEntry  
SEQUENCE    
  productIdentificationPerBoxIndex INTEGER
  productIdentificationSerialNumber DisplayString
  productIdentificationAssetTag DisplayString
  productIdentificationServiceTag DisplayString
  productIdentificationChassisServiceTag DisplayString
  productIdentificationBootromVersion DisplayString
  productIdentificationPiecePartID DisplayString
  productIdentificationPPIDRevision DisplayString
  productIdentificationExpressServiceCode DisplayString

EnvMonFanStatusEntry  
SEQUENCE    
  envMonFanStatusIndex INTEGER
  envMonFanStatusDescr DisplayString
  envMonFanState EnvMonState
  envMonFanSpeed INTEGER

EnvMonSupplyStatusEntry  
SEQUENCE    
  envMonSupplyStatusIndex INTEGER
  envMonSupplyStatusDescr DisplayString
  envMonSupplyState EnvMonState
  envMonSupplyCurrentPower INTEGER
  envMonSupplyAveragePower INTEGER
  envMonSupplyAvgStartTime DateAndTime
  envMonSupplySource INTEGER

Defined Values

dell 1.3.6.1.4.1.674
OBJECT IDENTIFIER    

dellLan 1.3.6.1.4.1.674.10895
OBJECT IDENTIFIER    

dellLanStandard 1.3.6.1.4.1.674.10895.5000
OBJECT IDENTIFIER    

dellLanCommon 1.3.6.1.4.1.674.10895.5000.1
OBJECT IDENTIFIER    

dellLanExtension 1.3.6.1.4.1.674.10895.5000.2
OBJECT IDENTIFIER    

powerConnectVendorMIB 1.3.6.1.4.1.674.10895.3000
Adding new objects - Dell PPID, Revision, Express Service Code.
MODULE-IDENTITY    

dellVendorMIBObjects 1.3.6.1.4.1.674.10895.3000.1
OBJECT IDENTIFIER    

dellVendorNotifications 1.3.6.1.4.1.674.10895.3000.2
OBJECT IDENTIFIER    

hardware 1.3.6.1.4.1.674.10895.3000.1.2
OBJECT IDENTIFIER    

productIdentification 1.3.6.1.4.1.674.10895.3000.1.2.100
OBJECT IDENTIFIER    

productStatus 1.3.6.1.4.1.674.10895.3000.1.2.110
OBJECT IDENTIFIER    

productIdentificationDisplayName 1.3.6.1.4.1.674.10895.3000.1.2.100.1
Name of this product for display purposes.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationDescription 1.3.6.1.4.1.674.10895.3000.1.2.100.2
A short description of this product such as: Ethernet Router Switch.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationVendor 1.3.6.1.4.1.674.10895.3000.1.2.100.3
The name of the product manufacturer, such as: Dell Inc.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationVersion 1.3.6.1.4.1.674.10895.3000.1.2.100.4
The version of this product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationBuildNumber 1.3.6.1.4.1.674.10895.3000.1.2.100.5
The software build number of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationURL 1.3.6.1.4.1.674.10895.3000.1.2.100.6
The URL of the web-based application to manage this device, should the device provide one. The format of the value held by this object is: http://.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationDeviceNetworkName 1.3.6.1.4.1.674.10895.3000.1.2.100.7
Device Name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationPerUnitTable 1.3.6.1.4.1.674.10895.3000.1.2.100.8
Identification specific to product instance and, in case of stackable products, per unit. If the product is not stackable, it will be considered a stack of one unit and therefore this table will contain one conceptual row only.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProductIdentificationPerBoxEntry

productIdentificationPerUnitEntry 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1
This row applies to a unit in a stackable product.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProductIdentificationPerBoxEntry  

productIdentificationPerBoxIndex 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.1
The index of the stack unit to which this conceptual row corresponds. Note that the index will be the same index as the index of a 'chassis' physical entity in the entity MIB of the product.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

productIdentificationSerialNumber 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.2
Serial number of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationAssetTag 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.3
Asset tag of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationServiceTag 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.4
Service tag of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationChassisServiceTag 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.5
Chassis Service tag of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationBootromVersion 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.6
The boot image version of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

productIdentificationPiecePartID 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.7
The piece part id of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..24)  

productIdentificationPPIDRevision 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.8
The PPID revision of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..3)  

productIdentificationExpressServiceCode 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.9
The express cervice code of the product.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..14)  

productIdentificationBannerMotdAckMode 1.3.6.1.4.1.674.10895.3000.1.2.100.9
If enable is selected, user will be required to acknowledge the banner displayed on the console. The user would have to type 'y' or 'n' to continue to the login prompt. If n is typed, the session is terminated and no future communication is allowed on that session. However, serial connection will not get terminated if user does not enter 'y'. Use disable option to disable banner acknowledge.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

productStatusGlobalStatus 1.3.6.1.4.1.674.10895.3000.1.2.110.1
Current status of the product.This is a rollup for the entire product. The status is intended to give initiative to a snmp monitor to get further data when this status is abnormal. This variable can take the following values: 3: OK If fans and power supplies are functioning and the system did not reboot because of a HW watchdog failure or a SW fatal error condition. 4: Non-critical If at least one power supply is not functional or the system rebooted at least once because of a HW watchdog failure or a SW fatal error condition. 5: Critical If at least one fan is not functional, possibly causing a dangerous warming up of the device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(3), non-critical(4), critical(5)  

productStatusLastGlobalStatus 1.3.6.1.4.1.674.10895.3000.1.2.110.2
The status before the current status which induced an initiative to issue a global status change trap.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(3), non-critical(4), critical(5)  

productStatusTimeStamp 1.3.6.1.4.1.674.10895.3000.1.2.110.3
The last time that the product global status has been updated. The time will be given in TimeTicks
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

productStatusGetTimeOut 1.3.6.1.4.1.674.10895.3000.1.2.110.4
Suggested time out value in milliseconds for how long the SNMP getter should wait while attempting to poll the product SNMP service.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

productStatusRefreshRate 1.3.6.1.4.1.674.10895.3000.1.2.110.5
Rate in seconds at which the SNMP service cached data is being updated.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..100  

productStatusGeneratingTrapsFlag 1.3.6.1.4.1.674.10895.3000.1.2.110.6
Indicates if this SNMP service is generating SNMP Traps. This variable can take the following values: 1: true - The device is capable and currently configured to generate traps if necessary. 2: false - The device is not capable of generating traps. 3: disabled - The device is capable but not configured to generate traps.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2), disabled(3)  

productStatusEnvironment 1.3.6.1.4.1.674.10895.3000.1.2.110.7
OBJECT IDENTIFIER    

envMonFanStatusTable 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1
The table of fan status maintained by the environmental monitor. Not Supported by Dell Modular Blade Server switches.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnvMonFanStatusEntry

envMonFanStatusEntry 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1.1
An entry in the fan status table, representing the status of the associated fan maintained by the environmental monitor. Not Supported by Dell Modular Blade Server switches.
Status: current Access: not-accessible
OBJECT-TYPE    
  EnvMonFanStatusEntry  

envMonFanStatusIndex 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1.1.1
Unique index for the fan being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning. Not Supported by Dell Modular Blade Server switches.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

envMonFanStatusDescr 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1.1.2
Textual description of the fan being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry. Not Supported by Dell Modular Blade Server switches.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

envMonFanState 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1.1.3
The mandatory state of the fan being instrumented. Not Supported by Dell Modular Blade Server switches.
Status: current Access: read-only
OBJECT-TYPE    
  EnvMonState  

envMonFanSpeed 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1.1.4
Speed of the fan being instrumented. Not Supported by Dell Modular Blade Server switches.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

envMonSupplyStatusTable 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2
The table of power supply status maintained by the environmental monitor card.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnvMonSupplyStatusEntry

envMonSupplyStatusEntry 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1
An entry in the power supply status table, representing the status of the associated power supply maintained by the environmental monitor card.
Status: current Access: not-accessible
OBJECT-TYPE    
  EnvMonSupplyStatusEntry  

envMonSupplyStatusIndex 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.1
Unique index for the power supply being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

envMonSupplyStatusDescr 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.2
Textual description of the power supply being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

envMonSupplyState 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.3
The mandatory state of the power supply being instrumented.
Status: current Access: read-only
OBJECT-TYPE    
  EnvMonState  

envMonSupplySource 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.4
The power supply source. unknown - Power supply source unknown ac - AC power supply dc - DC power supply externalPowerSupply - External power supply internalRedundant - Internal redundant power supply
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), ac(2), dc(3), externalPowerSupply(4), internalRedundant(5)  

envMonSupplyCurrentPower 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.5
Current power consumption of the power supply being instrumented. 0 - indicates that Current power is not available for related supply.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0 | 1..2147483647  

envMonSupplyAveragePower 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.6
Average power consumption of the power supply being instrumented. 0 - indicates that Average power is not available for related supply.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0 | 1..2147483647  

envMonSupplyAvgStartTime 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.7
The power supply data start. 0 - indicates that power and related start time is not available for supply.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

dellVendorTraps 1.3.6.1.4.1.674.10895.3000.2.1
OBJECT IDENTIFIER    

dellVendorTrapsPrefix 1.3.6.1.4.1.674.10895.3000.2.1.0
OBJECT IDENTIFIER    

productStatusGlobalStatusChange 1.3.6.1.4.1.674.10895.3000.2.1.0.1
This trap is sent when the product global status changes.
Status: current Access: read-only
NOTIFICATION-TYPE