DVB-CABLE-NIU-IF-MIB
File:
DVB-CABLE-NIU-IF-MIB.mib (30891 bytes)
Imported modules
Imported symbols
Defined Types
| DvbNiuMacCapEntry |
|
| SEQUENCE |
|
|
|
| |
dvbNiuMacCapVer |
INTEGER |
|
| |
dvbNiuMacCapEncap |
BITS |
|
| |
dvbNiuMacCapResReqCap |
TruthValue |
|
| |
dvbNiuMacCapFragMacMess |
TruthValue |
|
| |
dvbNiuMacCapSecSupp |
TruthValue |
|
| |
dvbNiuMacCapMinislots |
TruthValue |
|
| |
dvbNiuMacCapIbSig |
TruthValue |
|
| |
dvbNiuMacCapOobSig |
TruthValue |
|
| |
dvbNiuMacCapDsOobBr |
BITS |
|
| |
dvbNiuMacCapUsBr |
BITS |
|
| |
dvbNiuMacCapMaxConn |
Gauge32 |
|
| |
dvbNiuMacCapOperation |
INTEGER |
|
| DvbNiuMacStatsEntry |
|
| SEQUENCE |
|
|
|
| |
dvbNiuMacHwVer |
SnmpAdminString |
|
| |
dvbNiuMacStatStatus |
INTEGER |
|
| |
dvbNiuMacStatSlotCfgCrcErrs |
Gauge32 |
|
| |
dvbNiuMacStatRsCorrErrs |
Gauge32 |
|
| |
dvbNiuMacStatATMPacketLosses |
Gauge32 |
|
| |
dvbNiuMacStatSlotConfigCount |
Gauge32 |
|
| |
dvbNiuMacStatSlEsfCrcErrs |
Gauge32 |
|
| |
dvbNiuMacStatRsErrCorrFrms |
Gauge32 |
|
| |
dvbNiuMacStatRsErrNonCorrFrms |
Gauge32 |
|
| |
dvbNiuMacStatSlEsfFrameCount |
Gauge32 |
|
| |
dvbNiuMacStatConCount |
Gauge32 |
|
| DvbNiuRfDsEntry |
|
| SEQUENCE |
|
|
|
| |
dvbNiuRfDsHwVer |
SnmpAdminString |
|
| |
dvbNiuRfDsLastGoodFreq |
Integer32 |
|
| |
dvbNiuRfDsBackupFreq |
Integer32 |
|
| |
dvbNiuRfDsLowScanFreq |
Integer32 |
|
| |
dvbNiuRfDsHighScanFreq |
Integer32 |
|
| |
dvbNiuRfDsScanStep |
Integer32 |
|
| |
dvbNiuRfDsOobFreq |
Integer32 |
|
| |
dvbNiuRfDsIbFreq |
Integer32 |
|
| |
dvbNiuRfDsModType |
INTEGER |
|
| |
dvbNiuRfDsSnrEst |
Integer32 |
|
| |
dvbNiuRfDsPwrLevelEst |
Integer32 |
|
| DvbNiuRfUsEntry |
|
| SEQUENCE |
|
|
|
| |
dvbNiuRfUsHwVer |
SnmpAdminString |
|
| |
dvbNiuRfUsFreq |
Integer32 |
|
| |
dvbNiuRfUsPwrCtrlSetting |
Integer32 |
|
| |
dvbNiuRfUsTimeOffsetValue |
Integer32 |
|
Defined Values
| dvbNiuIf |
1.3.6.1.2.1.10.1 |
| The information module for the DVB interfaces
found in an EuroModem. |
| MODULE-IDENTITY |
|
|
|
| dvbNiuMacCapTable |
1.3.6.1.2.1.10.1.1.1.1 |
| This table contains all available MAC capabilites specified
in ETS 300 800 (8/3/1999) and identifies whether they are
supported on the MAC interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DvbNiuMacCapEntry |
|
| dvbNiuMacCapEntry |
1.3.6.1.2.1.10.1.1.1.1.1 |
| A row provides the supported capabilities for a single MAC
interface. An entry in this table exists for each ifEntry
with an ifType of dvbRccMacLayer. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DvbNiuMacCapEntry |
|
|
| dvbNiuMacCapVer |
1.3.6.1.2.1.10.1.1.1.1.1.1 |
| The mac protocol version. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
davic11(1), davic12(2), en301199(20), ets300800v2(29), ets300800v1(30) |
|
| dvbNiuMacCapEncap |
1.3.6.1.2.1.10.1.1.1.1.1.2 |
| This field is used to identify the encapsulation
types supported. These can be direct IP, Ethernet MAC
bridging and PPP. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BITS |
directIp(0), ethernetMacBridge(1), ppp(2) |
|
| dvbNiuMacCapResReqCap |
1.3.6.1.2.1.10.1.1.1.1.1.3 |
| True if the NIU is able to send MAC Resource Request
Messages. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dvbNiuMacCapSecSupp |
1.3.6.1.2.1.10.1.1.1.1.1.5 |
| True if the NIU supports the security extensions defined
in ETS 300 800. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dvbNiuMacCapMinislots |
1.3.6.1.2.1.10.1.1.1.1.1.6 |
| True if the NIU is capable of utilising minislots. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dvbNiuMacCapIbSig |
1.3.6.1.2.1.10.1.1.1.1.1.7 |
| True if the NIU is capable of utilising in band
signalling. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dvbNiuMacCapOobSig |
1.3.6.1.2.1.10.1.1.1.1.1.8 |
| True if the NIU is capable of utilising out of band
signalling. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dvbNiuMacCapDsOobBr |
1.3.6.1.2.1.10.1.1.1.1.1.9 |
| This field is used to identify the downstream out of band
bit rates supported. These are 1.544Mbit/s and 3.088Mbit/s.
If dvbNiuMacCapOobSig is false then the value of this
Object will be zero. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BITS |
d1o544Mbit(0), d3o088Mbit(1) |
|
| dvbNiuMacCapUsBr |
1.3.6.1.2.1.10.1.1.1.1.1.10 |
| This field is used to identify the upstream bit rates
supported. These are 256kbit/s, 1.544Mbit/s, 3.088Mbit/s
and 6.176Mbit/s. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BITS |
u256kbit(0), u1o544Mbit(1), u3o88Mbit(2), u6o176Mbit(3) |
|
| dvbNiuMacCapMaxConn |
1.3.6.1.2.1.10.1.1.1.1.1.11 |
| The maximum number of connections supported by the NIU. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dvbNiuMacCapOperation |
1.3.6.1.2.1.10.1.1.1.1.1.12 |
| The operational mode of the NIU, this can be either
one-way or two-way. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
one-way(1), two-way(2) |
|
| dvbNiuMacStatsTable |
1.3.6.1.2.1.10.1.1.2.1 |
| This table contains statistics/status associated with the
MAC interface. Reading these statistics does not cause
the values to be reset. If the statistics are read via a
MAC message they will be reset!
Note: The error statistics are represented by only 16 bits,
this is because the status message only uses 16 bits for
the values. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DvbNiuMacStatsEntry |
|
| dvbNiuMacStatsEntry |
1.3.6.1.2.1.10.1.1.2.1.1 |
| A row provides the statistics/status for a single MAC
interface. An entry in this table exists for each ifEntry
with an ifType of dvbRccMacLayer. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DvbNiuMacStatsEntry |
|
|
| dvbNiuMacHwVer |
1.3.6.1.2.1.10.1.1.2.1.1.1 |
| The hardware version of the MAC interface. The is a free
format text field. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
SnmpAdminString |
|
|
| dvbNiuMacStatStatus |
1.3.6.1.2.1.10.1.1.2.1.1.2 |
| The operational status of the NIU. The statuses 1-8 are
from ETS 300 800. The status other(9) is used for any case
that is not explicitly identified |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
scanningForCarrier(1), provisioning(2), invalidSTBNIU(3), timingRangingError(4), powerRangingError(5), running(6), stopped(7), none(8), other(9) |
|
| dvbNiuMacStatSlotCfgCrcErrs |
1.3.6.1.2.1.10.1.1.2.1.1.3 |
| Counts the number of errors in Slot_Configuration_Count
R bytes, as found by the CRC decoder. This object is
initialized to 0 at boot and is reset only upon reboot or
by a MAC Status message. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..65535 |
|
| dvbNiuMacStatRsCorrErrs |
1.3.6.1.2.1.10.1.1.2.1.1.4 |
| Counts the number of errors as corrected by the Reed
Solomon decoder. This object is initialized to 0 at boot
and is reset only upon reboot or by a MAC Status message. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..65535 |
|
| dvbNiuMacStatATMPacketLosses |
1.3.6.1.2.1.10.1.1.2.1.1.5 |
| Counts the number of received ATM cells that were lost,
either due to unrecoverable Reed Solomon errors or because
of an erroneous HEC of the ATM cells header. This object
is initialized to 0 at boot and is reset only upon reboot
or by a MAC Status message. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..65535 |
|
| dvbNiuMacStatSlotConfigCount |
1.3.6.1.2.1.10.1.1.2.1.1.6 |
| This refers to the number of R-byte sets (Rxa-Rxc) used to
calculate Slot_Configuration_CRC_Error_Count. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..65535 |
|
| dvbNiuMacStatSlEsfCrcErrs |
1.3.6.1.2.1.10.1.1.2.1.1.7 |
| Counts the number of CRC errrors found in consecutive
C1-C6.
This object is initialized to 0 at boot and is reset only
upon reboot or by a MAC Status message. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..65535 |
|
| dvbNiuMacStatRsErrCorrFrms |
1.3.6.1.2.1.10.1.1.2.1.1.8 |
| Counts the number of MPEG frames received with correctable
Reed Solomon errors (IB only). This object is initialized
to 0 at boot and is reset only upon reboot or by a MAC
Status message. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..65535 |
|
| dvbNiuMacStatRsErrNonCorrFrms |
1.3.6.1.2.1.10.1.1.2.1.1.9 |
| Counts the number of MPEG frames received with non
correctable Reed Solomon errors (IB only). This object is
initialized to 0 at boot and is reset only upon reboot or
by a MAC Status message. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..65535 |
|
| dvbNiuMacStatSlEsfFrameCount |
1.3.6.1.2.1.10.1.1.2.1.1.10 |
| This is the number of frames the statistics in this message
apply on. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..65535 |
|
| dvbNiuRfDsTable |
1.3.6.1.2.1.10.1.2.1.1 |
| This table contains RF characteristcs and counters for the
downstream interfaces. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DvbNiuRfDsEntry |
|
| dvbNiuRfDsEntry |
1.3.6.1.2.1.10.1.2.1.1.1 |
| A row provides the RF characteristcs, counters and possible
frequencies to use when locating a downstream channel for a
single downstream RF interface. An entry in this
table exists for each ifEntry with an ifType of
dvbRccDownstream |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DvbNiuRfDsEntry |
|
|
| dvbNiuRfDsHwVer |
1.3.6.1.2.1.10.1.2.1.1.1.1 |
| The hardware version of the downstream RF interface. The
is a free format text field. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
SnmpAdminString |
|
|
| dvbNiuRfDsLastGoodFreq |
1.3.6.1.2.1.10.1.2.1.1.1.2 |
| This is the last known good frequency for a downstream
channel and is used to locate the channel on power up or
reset. If a downstream channel cannot be found at the
frequency held by this object then dvbNiuRfDsBackupFreq
is tried. If dvbNiuRfDsBackupFreq fails then a frequency
scan is performed between dvbNiuRfDsMinScanFreq and
dvbNiuRfDsMaxScanFreq with a step size of
dvbNiuRfDsScanStep
This object will be updated with the freguency of the
channel found using the alternative frequencies. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
47000000..1000000000 |
|
| dvbNiuRfDsBackupFreq |
1.3.6.1.2.1.10.1.2.1.1.1.3 |
| This is a backup frequency for the downstream channel.
This will be used if dvbNiuRfDsLastGoodFreq fails. If this
frequency is successfully used then dvbNiuRfDsLastGoodFreq
is updated to contain it. If dvbNiuRfDsBackupFreq fails
then a frequency scan is performed between
dvbNiuRfDsMinScanFreq and dvbNiuRfDsMaxScanFreq with a step
size of dvbNiuRfDsScanStep. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
47000000..1000000000 |
|
| dvbNiuRfDsLowScanFreq |
1.3.6.1.2.1.10.1.2.1.1.1.4 |
| This is the start of the frequency range to be used
for scanning to find a downstream channel. If a downstream
channel is found then dvbNiuRfDsLastGoodFreq is updated to
contain the new frequency and the scan is terminated.
The step size used for the scan is dvbNiuRfDsScanStep. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
47000000..1000000000 |
|
| dvbNiuRfDsHighScanFreq |
1.3.6.1.2.1.10.1.2.1.1.1.5 |
| This is the end of the frequency range to be used for
scanningscan to find a downstream channel. If a downstream
channel is found then dvbNiuRfDsLastGoodFreq is updated to
contain the new frequency and the scan is terminated.
The step size used for the scan is dvbNiuRfDsScanStep. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
47000000..1000000000 |
|
| dvbNiuRfDsScanStep |
1.3.6.1.2.1.10.1.2.1.1.1.6 |
| This is the step size to be used when scanning for a
downstream channel. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
47000000..1000000000 |
|
| dvbNiuRfDsOobFreq |
1.3.6.1.2.1.10.1.2.1.1.1.7 |
| The frequency of the current downstream out of band
channel. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
47000000..1000000000 |
|
| dvbNiuRfDsIbFreq |
1.3.6.1.2.1.10.1.2.1.1.1.8 |
| The frequency of the current downstream in band channel. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
47000000..1000000000 |
|
| dvbNiuRfDsModType |
1.3.6.1.2.1.10.1.2.1.1.1.9 |
| The modulation type of the downstream channel. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
qpsk(2), qam8(3), qam16(4), qam32(5), qam64(6), qam128(7), qam256(8) |
|
| dvbNiuRfDsSnrEst |
1.3.6.1.2.1.10.1.2.1.1.1.10 |
| The estimated signal to noise ratio of the downstream
carrying MAC messages. If the SNR cannot be estinmated
it will be 0. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..255 |
|
| dvbNiuRfDsPwrLevelEst |
1.3.6.1.2.1.10.1.2.1.1.1.11 |
| The estimated power level of the downstream carrying
MAC messages. If the power level cannot be estinmated
it will be 0. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..255 |
|
| dvbNiuRfUsTable |
1.3.6.1.2.1.10.1.3.1.1 |
| This table contains RF characteristcs and counters for the
upstream interfaces. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DvbNiuRfUsEntry |
|
| dvbNiuRfUsEntry |
1.3.6.1.2.1.10.1.3.1.1.1 |
| A row provides the RF characteristcs and counters for a
single upstream RF interface. An entry in this table
exists for each ifEntry with an ifType of dvbRccUpstream |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DvbNiuRfUsEntry |
|
|
| dvbNiuRfUsHwVer |
1.3.6.1.2.1.10.1.3.1.1.1.1 |
| The hardware version of the upstream RF interface. The
is a free format text field. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
SnmpAdminString |
|
|
| dvbNiuRfUsFreq |
1.3.6.1.2.1.10.1.3.1.1.1.2 |
| The frequency of the upstream channel. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
5000000..65000000 |
|
| dvbNiuRfUsPwrCtrlSetting |
1.3.6.1.2.1.10.1.3.1.1.1.3 |
| The actual power used for the upstream transmission. The
unit of measure is 0.5dBuV |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..255 |
|
| dvbNiuRfUsTimeOffsetValue |
1.3.6.1.2.1.10.1.3.1.1.1.4 |
| This represents a relative offset of the upstream
transmission timing. A negative value indicates an
adjustment forward in time. A positive value indicates
an adjustment back in time. The unit of measure is 100
nsec |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
-32768..32767 |
|
| dvbNiuIfCompliance |
1.3.6.1.2.1.10.1.4.1.1 |
| The compliance statement for EuroModem NIUs
which implement the DVB-CABLE-NIU-IF-MIB MIB. |
| Status: current |
Access: read-only |
| MODULE-COMPLIANCE |
|
|
|
| dvbNiuMacGroup |
1.3.6.1.2.1.10.1.4.2.1 |
| A collection of objects providing capabilities and
statistics for the MAC layer. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| dvbNiuDsRfGroup |
1.3.6.1.2.1.10.1.4.2.2 |
| A collection of objects providing capabilities and
statistics for the downstream RF interface. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| dvbNiuUsRfGroup |
1.3.6.1.2.1.10.1.4.2.3 |
| A collection of objects providing capabilities and
statistics for the upstream RF interface. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|