DOCS-QOS3-MIB

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
SNMP-FRAMEWORK-MIB	IF-MIB	INET-ADDRESS-MIB
DIFFSERV-DSCP-TC	DOCS-L2VPN-MIB	DOCS-IF3-MIB
CLAB-DEF-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Unsigned32
Counter32	Counter64	OBJECT-GROUP
MODULE-COMPLIANCE	TEXTUAL-CONVENTION	RowStatus
TruthValue	MacAddress	TimeStamp
StorageType	SnmpAdminString	InterfaceIndex
ifIndex	InetAddressType	InetAddress
InetPortNumber	DscpOrAny	DocsL2vpnIfList
AttributeMask	AttrAggrRuleMask	ChSetId
Dsid	ChId	ChannelList
clabProjDocsis

Defined Types

IfDirection
Indicates a direction on an RF MAC interface. The value downstream(1) is from Cable Modem Termination System to Cable Modem. The value upstream(2) is from Cable Modem to Cable Modem Termination System.
TEXTUAL-CONVENTION
	INTEGER	downstream(1), upstream(2)

DOCSQOS3BitRate
The rate of traffic in unit of bits per second. Used to specify traffic rate for QOS.
TEXTUAL-CONVENTION
	Unsigned32

SchedulingType
The scheduling service provided by a CMTS for an upstream Service Flow. If the parameter is omitted from an upstream QOS Parameter Set, this object takes the value of bestEffort (2). This parameter must be reported as undefined (1) for downstream QOS Parameter Sets.
TEXTUAL-CONVENTION
	INTEGER	undefined(1), bestEffort(2), nonRealTimePollingService(3), realTimePollingService(4), unsolictedGrantServiceWithAD(5), unsolictedGrantService(6)

DocsQos3PktClassEntry
SEQUENCE
	docsQos3PktClassId	Unsigned32
	docsQos3PktClassDirection	IfDirection
	docsQos3PktClassPriority	Unsigned32
	docsQos3PktClassIpTosLow	OCTET STRING
	docsQos3PktClassIpTosHigh	OCTET STRING
	docsQos3PktClassIpTosMask	OCTET STRING
	docsQos3PktClassIpProtocol	Unsigned32
	docsQos3PktClassIpSourceAddr	InetAddress
	docsQos3PktClassIpSourceMask	InetAddress
	docsQos3PktClassIpDestAddr	InetAddress
	docsQos3PktClassIpDestMask	InetAddress
	docsQos3PktClassSourcePortStart	InetPortNumber
	docsQos3PktClassSourcePortEnd	InetPortNumber
	docsQos3PktClassDestPortStart	InetPortNumber
	docsQos3PktClassDestPortEnd	InetPortNumber
	docsQos3PktClassDestMacAddr	MacAddress
	docsQos3PktClassDestMacMask	MacAddress
	docsQos3PktClassSourceMacAddr	MacAddress
	docsQos3PktClassEnetProtocolType	INTEGER
	docsQos3PktClassEnetProtocol	Unsigned32
	docsQos3PktClassUserPriLow	Unsigned32
	docsQos3PktClassUserPriHigh	Unsigned32
	docsQos3PktClassVlanId	Unsigned32
	docsQos3PktClassState	INTEGER
	docsQos3PktClassPkts	Counter64
	docsQos3PktClassBitMap	BITS
	docsQos3PktClassIpAddrType	InetAddressType
	docsQos3PktClassFlowLabel	Unsigned32
	docsQos3PktClassCmInterfaceMask	DocsL2vpnIfList

DocsQos3ParamSetEntry
SEQUENCE
	docsQos3ParamSetServiceClassName	SnmpAdminString
	docsQos3ParamSetPriority	Unsigned32
	docsQos3ParamSetMaxTrafficRate	DOCSQOS3BitRate
	docsQos3ParamSetMaxTrafficBurst	Unsigned32
	docsQos3ParamSetMinReservedRate	DOCSQOS3BitRate
	docsQos3ParamSetMinReservedPkt	Unsigned32
	docsQos3ParamSetActiveTimeout	Unsigned32
	docsQos3ParamSetAdmittedTimeout	Unsigned32
	docsQos3ParamSetMaxConcatBurst	Unsigned32
	docsQos3ParamSetSchedulingType	SchedulingType
	docsQos3ParamSetNomPollInterval	Unsigned32
	docsQos3ParamSetTolPollJitter	Unsigned32
	docsQos3ParamSetUnsolicitGrantSize	Unsigned32
	docsQos3ParamSetNomGrantInterval	Unsigned32
	docsQos3ParamSetTolGrantJitter	Unsigned32
	docsQos3ParamSetGrantsPerInterval	Unsigned32
	docsQos3ParamSetTosAndMask	OCTET STRING
	docsQos3ParamSetTosOrMask	OCTET STRING
	docsQos3ParamSetMaxLatency	Unsigned32
	docsQos3ParamSetType	INTEGER
	docsQos3ParamSetRequestPolicyOct	OCTET STRING
	docsQos3ParamSetBitMap	BITS
	docsQos3ParamSetServiceFlowId	Unsigned32
	docsQos3ParamSetRequiredAttrMask	AttributeMask
	docsQos3ParamSetForbiddenAttrMask	AttributeMask
	docsQos3ParamSetAttrAggrRuleMask	AttrAggrRuleMask
	docsQos3ParamSetAppId	Unsigned32
	docsQos3ParamSetMultiplierContentionReqWindow	Unsigned32
	docsQos3ParamSetMultiplierBytesReq	Unsigned32
	docsQos3ParamSetMaxReqPerSidCluster	Unsigned32
	docsQos3ParamSetMaxOutstandingBytesPerSidCluster	Unsigned32
	docsQos3ParamSetMaxTotBytesReqPerSidCluster	Unsigned32
	docsQos3ParamSetMaxTimeInSidCluster	Unsigned32
	docsQos3ParamSetPeakTrafficRate	Unsigned32
	docsQos3ParamSetDsResequencing	INTEGER

DocsQos3ServiceFlowEntry
SEQUENCE
	docsQos3ServiceFlowId	Unsigned32
	docsQos3ServiceFlowSID	Unsigned32
	docsQos3ServiceFlowDirection	IfDirection
	docsQos3ServiceFlowPrimary	TruthValue
	docsQos3ServiceFlowParamSetTypeStatus	BITS
	docsQos3ServiceFlowChSetId	ChSetId
	docsQos3ServiceFlowAttrAssignSuccess	TruthValue
	docsQos3ServiceFlowDsid	Dsid

DocsQos3ServiceFlowStatsEntry
SEQUENCE
	docsQos3ServiceFlowPkts	Counter64
	docsQos3ServiceFlowOctets	Counter64
	docsQos3ServiceFlowTimeCreated	TimeStamp
	docsQos3ServiceFlowTimeActive	Counter32
	docsQos3ServiceFlowPHSUnknowns	Counter32
	docsQos3ServiceFlowPolicedDropPkts	Counter32
	docsQos3ServiceFlowPolicedDelayPkts	Counter32

DocsQos3UpstreamStatsEntry
SEQUENCE
	docsQos3SID	Unsigned32
	docsQos3UpstreamFragments	Counter32
	docsQos3UpstreamFragDiscards	Counter32
	docsQos3UpstreamConcatBursts	Counter32

DocsQos3DynamicServiceStatsEntry
SEQUENCE
	docsQos3IfDirection	IfDirection
	docsQos3DSAReqs	Counter32
	docsQos3DSARsps	Counter32
	docsQos3DSAAcks	Counter32
	docsQos3DSCReqs	Counter32
	docsQos3DSCRsps	Counter32
	docsQos3DSCAcks	Counter32
	docsQos3DSDReqs	Counter32
	docsQos3DSDRsps	Counter32
	docsQos3DynamicAdds	Counter32
	docsQos3DynamicAddFails	Counter32
	docsQos3DynamicChanges	Counter32
	docsQos3DynamicChangeFails	Counter32
	docsQos3DynamicDeletes	Counter32
	docsQos3DynamicDeleteFails	Counter32
	docsQos3DCCReqs	Counter32
	docsQos3DCCRsps	Counter32
	docsQos3DCCAcks	Counter32
	docsQos3DCCs	Counter32
	docsQos3DCCFails	Counter32
	docsQos3DCCRspDeparts	Counter32
	docsQos3DCCRspArrives	Counter32
	docsQos3DbcReqs	Counter32
	docsQos3DbcRsps	Counter32
	docsQos3DbcAcks	Counter32
	docsQos3DbcSuccesses	Counter32
	docsQos3DbcFails	Counter32
	docsQos3DbcPartial	Counter32

DocsQos3ServiceFlowLogEntry
SEQUENCE
	docsQos3ServiceFlowLogIndex	Unsigned32
	docsQos3ServiceFlowLogIfIndex	InterfaceIndex
	docsQos3ServiceFlowLogSFID	Unsigned32
	docsQos3ServiceFlowLogCmMac	MacAddress
	docsQos3ServiceFlowLogPkts	Counter64
	docsQos3ServiceFlowLogOctets	Counter64
	docsQos3ServiceFlowLogTimeDeleted	TimeStamp
	docsQos3ServiceFlowLogTimeCreated	TimeStamp
	docsQos3ServiceFlowLogTimeActive	Counter32
	docsQos3ServiceFlowLogDirection	IfDirection
	docsQos3ServiceFlowLogPrimary	TruthValue
	docsQos3ServiceFlowLogServiceClassName	SnmpAdminString
	docsQos3ServiceFlowLogPolicedDropPkts	Counter32
	docsQos3ServiceFlowLogPolicedDelayPkts	Counter32
	docsQos3ServiceFlowLogControl	INTEGER

DocsQos3ServiceClassEntry
SEQUENCE
	docsQos3ServiceClassName	SnmpAdminString
	docsQos3ServiceClassStatus	RowStatus
	docsQos3ServiceClassPriority	Unsigned32
	docsQos3ServiceClassMaxTrafficRate	DOCSQOS3BitRate
	docsQos3ServiceClassMaxTrafficBurst	Unsigned32
	docsQos3ServiceClassMinReservedRate	DOCSQOS3BitRate
	docsQos3ServiceClassMinReservedPkt	Unsigned32
	docsQos3ServiceClassMaxConcatBurst	Unsigned32
	docsQos3ServiceClassNomPollInterval	Unsigned32
	docsQos3ServiceClassTolPollJitter	Unsigned32
	docsQos3ServiceClassUnsolicitGrantSize	Unsigned32
	docsQos3ServiceClassNomGrantInterval	Unsigned32
	docsQos3ServiceClassTolGrantJitter	Unsigned32
	docsQos3ServiceClassGrantsPerInterval	Unsigned32
	docsQos3ServiceClassMaxLatency	Unsigned32
	docsQos3ServiceClassActiveTimeout	Unsigned32
	docsQos3ServiceClassAdmittedTimeout	Unsigned32
	docsQos3ServiceClassSchedulingType	SchedulingType
	docsQos3ServiceClassRequestPolicy	OCTET STRING
	docsQos3ServiceClassTosAndMask	OCTET STRING
	docsQos3ServiceClassTosOrMask	OCTET STRING
	docsQos3ServiceClassDirection	IfDirection
	docsQos3ServiceClassStorageType	StorageType
	docsQos3ServiceClassDSCPOverwrite	DscpOrAny
	docsQos3ServiceClassRequiredAttrMask	AttributeMask
	docsQos3ServiceClassForbiddenAttrMask	AttributeMask
	docsQos3ServiceClassAttrAggrRuleMask	AttrAggrRuleMask
	docsQos3ServiceClassAppId	Unsigned32
	docsQos3ServiceClassMultiplierContentionReqWindow	Unsigned32
	docsQos3ServiceClassMultiplierBytesReq	Unsigned32
	docsQos3ServiceClassMaxReqPerSidCluster	Unsigned32
	docsQos3ServiceClassMaxOutstandingBytesPerSidCluster	Unsigned32
	docsQos3ServiceClassMaxTotBytesReqPerSidCluster	Unsigned32
	docsQos3ServiceClassMaxTimeInSidCluster	Unsigned32
	docsQos3ServiceClassPeakTrafficRate	Unsigned32
	docsQos3ServiceClassDsResequencing	INTEGER

DocsQos3PHSEntry
SEQUENCE
	docsQos3PHSField	OCTET STRING
	docsQos3PHSMask	OCTET STRING
	docsQos3PHSSize	Unsigned32
	docsQos3PHSVerify	TruthValue
	docsQos3PHSIndex	Unsigned32

DocsQos3CmtsMacToSrvFlowEntry
SEQUENCE
	docsQos3CmtsCmMac	MacAddress
	docsQos3CmtsServiceFlowId	Unsigned32
	docsQos3CmtsIfIndex	InterfaceIndex

DocsQos3ServiceFlowSidClusterEntry
SEQUENCE
	docsQos3ServiceFlowSidClusterId	Unsigned32
	docsQos3ServiceFlowSidClusterUcid	ChId
	docsQos3ServiceFlowSidClusterSid	Unsigned32

DocsQos3GrpServiceFlowEntry
SEQUENCE
	docsQos3GrpServiceFlowIsDef	TruthValue
	docsQos3GrpServiceFlowQosConfigId	Unsigned32
	docsQos3GrpServiceFlowNumSess	Unsigned32

DocsQos3GrpPktClassEntry
SEQUENCE
	docsQos3GrpPktClassGrpConfigId	Unsigned32

DocsQos3UpChCounterExtEntry
SEQUENCE
	docsQos3UpChCounterExtSgmtValids	Counter32
	docsQos3UpChCounterExtSgmtDiscards	Counter32

DocsQos3ServiceFlowCcfStatsEntry
SEQUENCE
	docsQos3ServiceFlowCcfStatsSgmtValids	Counter32
	docsQos3ServiceFlowCcfStatsSgmtLost	Counter32

DocsQos3CmServiceUsStatsEntry
SEQUENCE
	docsQos3CmServiceUsStatsTxSlotsImmed	Counter32
	docsQos3CmServiceUsStatsTxSlotsDed	Counter32
	docsQos3CmServiceUsStatsTxRetries	Counter32
	docsQos3CmServiceUsStatsTxExceededs	Counter32
	docsQos3CmServiceUsStatsRqRetries	Counter32
	docsQos3CmServiceUsStatsRqExceededs	Counter32
	docsQos3CmServiceUsStatsSgmts	Counter32

DocsQos3CmtsDsidEntry
SEQUENCE
	docsQos3CmtsDsidDsid	Dsid
	docsQos3CmtsDsidUsage	BITS
	docsQos3CmtsDsidDsChSet	ChSetId
	docsQos3CmtsDsidReseqWaitTime	Unsigned32
	docsQos3CmtsDsidReseqWarnThrshld	Unsigned32
	docsQos3CmtsDsidStatusHldoffTimerSeqOutOfRng	Unsigned32
	docsQos3CmtsDsidCurrentSeqNum	Unsigned32

DocsQos3CmtsDebugDsidEntry
SEQUENCE
	docsQos3CmtsDebugDsidDsid	Dsid
	docsQos3CmtsDebugDsidRowStatus	RowStatus

DocsQos3CmtsDebugDsidStatsEntry
SEQUENCE
	docsQos3CmtsDebugDsidStatsDsIfIndex	InterfaceIndex
	docsQos3CmtsDebugDsidStatsDsidPackets	Counter64
	docsQos3CmtsDebugDsidStatsDsidOctets	Counter64

DocsQos3CmDsidEntry
SEQUENCE
	docsQos3CmDsidDsid	Dsid
	docsQos3CmDsidUsage	BITS
	docsQos3CmDsidNumReseqChs	Unsigned32
	docsQos3CmDsidReseqChList	ChannelList
	docsQos3CmDsidReseqWaitTime	Unsigned32
	docsQos3CmDsidReseqWarnThrshld	Unsigned32
	docsQos3CmDsidStatusHldoffTimerSeqOutOfRng	Unsigned32
	docsQos3CmDsidOutOfRangeDiscards	Unsigned32
	docsQos3CmDsidNextExpectedSeqNum	Unsigned32
	docsQos3CmDsidCmInterfaceMask	DocsL2vpnIfList
	docsQos3CmDsidFwdCmInterfaceMask	DocsL2vpnIfList

DocsQos3CmDsidStatsEntry
SEQUENCE
	docsQos3CmDsidStatsDsid	Dsid
	docsQos3CmDsidStatsSeqNumMissing	Counter32
	docsQos3CmDsidStatsSkewThreshExceeds	Counter32
	docsQos3CmDsidStatsOutOfRangePackets	Counter32
	docsQos3CmDsidStatsNumPackets	Counter64

DocsQos3CmDsidClientEntry
SEQUENCE
	docsQos3CmDsidClientDsid	Dsid
	docsQos3CmDsidClientClientMacId	Unsigned32
	docsQos3CmDsidClientClientMacAddr	MacAddress

Defined Values

docsQos3Mib		1.3.6.1.4.1.4491.2.1.21
This MIB module contains the management objects for the management of QOS for channel bonding.
MODULE-IDENTITY

docsQos3MibObjects		1.3.6.1.4.1.4491.2.1.21.1
OBJECT IDENTIFIER

docsQos3PktClassTable		1.3.6.1.4.1.4491.2.1.21.1.1
This object describes the packet classification configured on the CM or CMTS. The model is that a packet either received as input from an interface or transmitted for output on an interface may be compared against an ordered list of rules pertaining to the packet contents. Each rule is an instance of this object. A matching rule provides a Service Flow ID to which the packet is classified. All rules need to match for a packet to match a classifier. The attibutes in this row correspond to a set of Classifier Encoding parameters in a DOCSIS MAC management message. The BitMap attribute indicates which particular parameters were present in the classifier as signaled in the DOCSIS message. If the referenced parameter was not present in the signaled Classifier, the corresponding attribute in this instance reports a value as specified by that attribute description.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3PktClassEntry

docsQos3PktClassEntry		1.3.6.1.4.1.4491.2.1.21.1.1.1
The conceptual row of docsQos3PktClassTable. The ifIndex key corresponds to the MAC Domain interface of the service flow of this classifier.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3PktClassEntry

docsQos3PktClassId		1.3.6.1.4.1.4491.2.1.21.1.1.1.1
This key indicates the assigned identifier to the packet classifier instance by the CMTS, which is unique per Service Flow. For UDCs this corresponds to the Service Flow Reference of the classifier.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..65535

docsQos3PktClassDirection		1.3.6.1.4.1.4491.2.1.21.1.1.1.2
This attribute indicates the direction to which the classifier is applied.
Status: current	Access: read-only
OBJECT-TYPE
	IfDirection

docsQos3PktClassPriority		1.3.6.1.4.1.4491.2.1.21.1.1.1.3
This attribute specifies the order of evaluation of the classifiers. The higher the value, the higher the priority. The value of 0 is used as default in provisioned Service Flows Classifiers. The default value of 64 is used for dynamic Service Flow Classifiers. If the referenced parameter is not present in a classifier, this attribute reports the default value as defined above.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

docsQos3PktClassIpTosLow		1.3.6.1.4.1.4491.2.1.21.1.1.1.4
This attribute indicates the low value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this attribute reports the value of 0. The IP TOS octet, as originally defined in RFC 791, has been superseded by the 6-bit Differentiated Services Field (DSField, RFC 3260) and the 2-bit Explicit Congestion Notification Field (ECN field, RFC 3168). This object is defined as an 8-bit octet as per the DOCSIS Specification for packet classification.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

docsQos3PktClassIpTosHigh		1.3.6.1.4.1.4491.2.1.21.1.1.1.5
This attribute indicates the 8-bit high value of a range of TOS byte values. If the referenced parameter is not present in a classifier, this attribute reports the value of 0. The IP TOS octet as originally defined in RFC 791 has been superseded by the 6-bit Differentiated Services Field (DSField, RFC 3260) and the 2-bit Explicit Congestion Notification Field (ECN field, RFC 3168). This object is defined as an 8-bit octet as defined by the DOCSIS Specification for packet classification.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

docsQos3PktClassIpTosMask		1.3.6.1.4.1.4491.2.1.21.1.1.1.6
This attribute indicates the mask value is bitwise ANDed with TOS byte in an IP packet, and this value is used for range checking of TosLow and TosHigh. If the referenced parameter is not present in a classifier, this attribute reports the value of 0. The IP TOS octet as originally defined in RFC 791 has been superseded by the 6-bit Differentiated Services Field (DSField, RFC 3260) and the 2-bit Explicit Congestion Notification Field (ECN field, RFC 3168). This object is defined as an 8-bit octet per the DOCSIS Specification for packet classification.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

docsQos3PktClassIpProtocol		1.3.6.1.4.1.4491.2.1.21.1.1.1.7
This attribute indicates the value of the IP Protocol field required for IP packets to match this rule. The value 256 matches traffic with any IP Protocol value. The value 257 by convention matches both TCP and UDP. If the referenced parameter is not present in a classifier, this attibute reports the value of 258.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..258

docsQos3PktClassIpSourceAddr		1.3.6.1.4.1.4491.2.1.21.1.1.1.8
This attribute specifies the value of the IP Source Address required for packets to match this rule. An IP packet matches the rule when the packet IP Source Address bitwise ANDed with the InetSourceMask value equals the InetSourceAddr value. The address type of this object is specified by InetAddressType. If the referenced parameter is not present in a classifier, this object reports the value of '00000000'H.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

docsQos3PktClassIpSourceMask		1.3.6.1.4.1.4491.2.1.21.1.1.1.9
This attribute specifies which bits of a packet's IP Source Address are compared to match this rule. An IP packet matches the rule when the packet source address bitwise ANDed with the InetSourceMask value equals the docsIetfQosIpPktClassInetSourceAddr value. The address type of this attribute is specified by InetAddressType. If the referenced parameter is not present in a classifier, this attribute reports the value of 'FFFFFFFF'H.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

docsQos3PktClassIpDestAddr		1.3.6.1.4.1.4491.2.1.21.1.1.1.10
This attribute specifies the value of the IP Destination Address required for packets to match this rule. An IP packet matches the rule when the packet IP Destination Address bitwise ANDed with the InetDestMask value equals the InetDestAddr value. The address type of this attribute is specified by InetAddressType. If the referenced parameter is not present in a classifier, this attribute reports the value of '00000000'H.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

docsQos3PktClassIpDestMask		1.3.6.1.4.1.4491.2.1.21.1.1.1.11
This attribute specifies which bits of a packet's IP Destination Address are compared to match this rule. An IP packet matches the rule when the packet destination address bitwise ANDed with the InetDestMask value equals the docsIetfQosIpPktClassInetDestAddr value. The address type of this attribute is specified by InetAddressType. If the referenced parameter is not present in a classifier, this attribute reports the value of 'FFFFFFFF'H.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddress

docsQos3PktClassSourcePortStart		1.3.6.1.4.1.4491.2.1.21.1.1.1.12
This attribute specifies the low-end inclusive range of TCP/UDP source port numbers to which a packet is compared. This attribute is irrelevant for non-TCP/UDP IP packets. If the referenced parameter is not present in a classifier, this attribute reports the value of 0.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

docsQos3PktClassSourcePortEnd		1.3.6.1.4.1.4491.2.1.21.1.1.1.13
This attribute specifies the high-end inclusive range of TCP/UDP source port numbers to which a packet is compared. This attribute is irrelevant for non-TCP/UDP IP packets. If the referenced parameter is not present in a classifier, this attribute reports the value of 65535.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

docsQos3PktClassDestPortStart		1.3.6.1.4.1.4491.2.1.21.1.1.1.14
This attribute specifies the low-end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present in a classifier, this attribute reports the value of 0.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

docsQos3PktClassDestPortEnd		1.3.6.1.4.1.4491.2.1.21.1.1.1.15
This attribute specifies the high-end inclusive range of TCP/UDP destination port numbers to which a packet is compared. If the referenced parameter is not present in a classifier, this attribute reports the value of 65535.
Status: current	Access: read-only
OBJECT-TYPE
	InetPortNumber

docsQos3PktClassDestMacAddr		1.3.6.1.4.1.4491.2.1.21.1.1.1.16
An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with DestMacMask equals the value of DestMacAddr. If the referenced parameter is not present in a classifier, this attribute reports the value of '000000000000'H.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

docsQos3PktClassDestMacMask		1.3.6.1.4.1.4491.2.1.21.1.1.1.17
An Ethernet packet matches an entry when its destination MAC address bitwise ANDed with DestMacMask equals the value of DestMacAddr. If the referenced parameter is not present in a classifier, this attribute reports the value of '000000000000'H.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

docsQos3PktClassSourceMacAddr		1.3.6.1.4.1.4491.2.1.21.1.1.1.18
An Ethernet packet matches this entry when its source MAC address equals the value of this attribute. If the referenced parameter is not present in a classifier, this attribute reports the value of 'FFFFFFFFFFFF'
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

docsQos3PktClassEnetProtocolType		1.3.6.1.4.1.4491.2.1.21.1.1.1.19
This attribute indicates the format of the layer 3 protocol ID in the Ethernet packet. A value of 'none' means that the rule does not use the layer 3 protocol type as a matching criteria. A value of 'ethertype' means that the rule applies only to frames that contain an EtherType value. Ethertype values are contained in packets using the Dec-Intel-Xerox (DIX) encapsulation or the RFC1042 Sub-Network Access Protocol (SNAP) encapsulation formats. A value of 'dsap' means that the rule applies only to frames using the IEEE802.3 encapsulation format with a Destination Service Access Point (DSAP) other than 0xAA (which is reserved for SNAP). A value of 'mac' means that the rule applies only to MAC management messages for MAC management messages. A value of 'all' means that the rule matches all Ethernet packets. If the Ethernet frame contains an 802.1P/Q Tag header (i.e., EtherType 0x8100), this attribute applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in a classifier, this attribute reports the value of 0.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), ethertype(1), dsap(2), mac(3), all(4)

docsQos3PktClassEnetProtocol		1.3.6.1.4.1.4491.2.1.21.1.1.1.20
If EnetProtocolType is 'none', this attribute is ignored when considering whether a packet matches the current rule. If EnetProtocolType is 'ethertype', this attribute gives the 16-bit value of the EtherType that the packet must match in order to match the rule. If EnetProtocolType is 'dsap', the lower 8 bits of this attribute's value must match the DSAP byte of the packet in order to match the rule. If EnetProtocolType is 'mac', the lower 8 bits of this attribute's value represent a lower bound (inclusive) of MAC management message type codes matched, and the upper 8 bits represent the upper bound (inclusive) of matched MAC message type codes. Certain message type codes are excluded from matching, as specified in the reference. If the Ethernet frame contains an 802.1P/Q Tag header (i.e., EtherType 0x8100), this attribute applies to the embedded EtherType field within the 802.1P/Q header. If the referenced parameter is not present in the classifier, the value of this attribute is reported as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3PktClassUserPriLow		1.3.6.1.4.1.4491.2.1.21.1.1.1.22
This attribute applies only to Ethernet frames using the 802.1P/Q tag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3-bit Priority field and a 12-bit VLAN number. Tagged Ethernet packets must have a 3-bit Priority field within the range of PriLow to PriHigh in order to match this rule. If the referenced parameter is not present in the classifier, the value of this attribute is reported as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..7

docsQos3PktClassUserPriHigh		1.3.6.1.4.1.4491.2.1.21.1.1.1.23
This attribute applies only to Ethernet frames using the 802.1P/Qtag header (indicated with EtherType 0x8100). Such frames include a 16-bit Tag that contains a 3-bit Priority field and a 12-bit VLAN number. Tagged Ethernet packets must have a 3-bit Priority field within the range of PriLow to PriHigh in order to match this rule. If the referenced parameter is not present in the classifier, the value of this attribute is reported as 7.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..7

docsQos3PktClassVlanId		1.3.6.1.4.1.4491.2.1.21.1.1.1.24
This attribute applies only to Ethernet frames using the 802.1P/Q tag header. Tagged packets must have a VLAN Identifier that matches the value in order to match the rule. If the referenced parameter is not present in the classifier, the value of this attribute is reported as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0 \| 1..4094

docsQos3PktClassState		1.3.6.1.4.1.4491.2.1.21.1.1.1.25
This attribute indicates whether or not the classifier is enabled to classify packets to a Service Flow. If the referenced parameter is not present in the classifier, the value of this attribute is reported as 'true'.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), inactive(2)

docsQos3PktClassPkts		1.3.6.1.4.1.4491.2.1.21.1.1.1.26
This attribute counts the number of packets that have been classified using this entry. This includes all packets delivered to a Service Flow maximum rate policing function, whether or not that function drops the packets. This counter's last discontinuity is the ifCounterDiscontinuityTime for the same ifIndex that indexes this attribute.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

docsQos3PktClassBitMap		1.3.6.1.4.1.4491.2.1.21.1.1.1.27
This attribute indicates which parameter encodings were actually present in the DOCSIS packet classifier encoding signaled in the DOCSIS message that created or modified the classifier. Note that Dynamic Service Change messages have replace semantics, so that all non-default parameters must be present whether the classifier is being created or changed. A bit of this attribute is set to 1 if the parameter indicated by the comment was present in the classifier encoding, and to 0 otherwise. Note that BITS are encoded most significant bit first, so that if, for example, bits 6 and 7 are set, this attribute is encoded as the octet string '030000'H.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	rulePriority(0), activationState(1), ipTos(2), ipProtocol(3), ipSourceAddr(4), ipSourceMask(5), ipDestAddr(6), ipDestMask(7), sourcePortStart(8), sourcePortEnd(9), destPortStart(10), destPortEnd(11), destMac(12), sourceMac(13), ethertype(14), userPri(15), vlanId(16), flowLabel(17), cmInterfaceMask(18)

docsQos3PktClassIpAddrType		1.3.6.1.4.1.4491.2.1.21.1.1.1.28
This attribute indicates the type of the Internet address for InetSourceAddr, InetSourceMask, InetDestAddr, and InetDestMask. If the referenced parameter is not present in a classifier, this object reports the value of 'ipv4'.
Status: current	Access: read-only
OBJECT-TYPE
	InetAddressType

docsQos3PktClassFlowLabel		1.3.6.1.4.1.4491.2.1.21.1.1.1.29
This attribute represents the Flow Label field in the IPv6 header to be matched by the classifier. The value zero indicates that the Flow Label is not specified as part of the classifier and is not matched against the packets.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..1048575

docsQos3PktClassCmInterfaceMask		1.3.6.1.4.1.4491.2.1.21.1.1.1.30
This attribute represents a bit-mask of the CM in-bound interfaces to which this classifer applies. This attribute only applies to QOS upstream Classifiers and upstream Drop Classifiers. For QOS downstream classifiers this object reports the zero-length string.
Status: current	Access: read-only
OBJECT-TYPE
	DocsL2vpnIfList

docsQos3ParamSetTable		1.3.6.1.4.1.4491.2.1.21.1.2
This object describes the set of QOS parameters defined in a managed device. DOCSIS 1.0 COS service profiles are not represented in this object. Each row corresponds to a DOCSIS QOS Parameter Set as signaled via DOCSIS MAC management messages.Each attribute of an instance of this object corresponds to one or part of oneService Flow Encoding. The BitMap attribute indicates which particular parameters were signaled in the original registration or dynamic service request message that created the QOS Parameter Set. In many cases, even if a QOS Parameter Set parameter was not signaled, the DOCSIS specification calls for a default value to be used. That default value is reported as the value of the corresponding attribute in this object instance. Many attributes are not applicable, depending on the Service Flow direction, upstream scheduling type or Service Flow bonding configuration. The attribute value reported in this case is specified by those attributes descriptions.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3ParamSetEntry

docsQos3ParamSetEntry		1.3.6.1.4.1.4491.2.1.21.1.2.1
The conceptual row of docsQos3ParamSetTable. The ifIndex key corresponds to the MAC Domain interface of the service flow of this Qos Param Set.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3ParamSetEntry

docsQos3ParamSetServiceClassName		1.3.6.1.4.1.4491.2.1.21.1.2.1.4
This attribute represents the Service Class Name from which the parameter set values were derived. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, this attribute returns the zero-length string.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..15)

docsQos3ParamSetPriority		1.3.6.1.4.1.4491.2.1.21.1.2.1.5
This attribute represents the relative priority of a Service Flow. Higher numbers indicate higher priority. This priority should only be used to differentiate Service Flow from identical parameter sets. This attribute returns 0 if the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set or if the parameter is not applicable.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..7

docsQos3ParamSetMaxTrafficRate		1.3.6.1.4.1.4491.2.1.21.1.2.1.6
This attribute represents the maximum sustained traffic rate allowed for this Service Flow in bits/sec. It counts all MAC frame data PDUs from the bytes following the MAC header HCS to the end of the CRC. The number of bytes forwarded is limited during any time interval. The value 0 means no maximum traffic rate is enforced. This attribute applies to both upstream and downstream Service Flows. This attribute returns 0 if the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, or if the parameter is not applicable.
Status: current	Access: read-only
OBJECT-TYPE
	DOCSQOS3BitRate

docsQos3ParamSetMaxTrafficBurst		1.3.6.1.4.1.4491.2.1.21.1.2.1.7
This attribute specifies the token bucket size in bytes for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. This object is applied in conjunction with MaxTrafficRate to calculate maximum sustained traffic rate. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, this attribute returns 3044 for scheduling types 'bestEffort', 'nonRealTimePollingService' and 'realTimePollingService'. If this parameter is not applicable, it is reported as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

docsQos3ParamSetMinReservedRate		1.3.6.1.4.1.4491.2.1.21.1.2.1.8
This attribute specifies the guaranteed minimum rate in bits/sec for this parameter set. The value is calculated from the byte following the MAC header HCS to the end of the CRC. The value of 0 indicates that no bandwidth is reserved. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, this attribute returns 0. If the parameter is not applicable, it is reported as 0.
Status: current	Access: read-only
OBJECT-TYPE
	DOCSQOS3BitRate

docsQos3ParamSetMinReservedPkt		1.3.6.1.4.1.4491.2.1.21.1.2.1.9
This attribute specifies an assumed minimum packet size in bytes for which the MinReservedRate will be provided. The value is calculated from the byte following the MAC header HCS to the end of the CRC. If the referenced parameter is omitted from a DOCSIS QOS parameter set, the used and reported value is CMTS implementation and the CM reports a value of 0. If the referenced parameter is not applicable to the direction or scheduling type of the Service Flow, both CMTS and CM report the value 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ParamSetActiveTimeout		1.3.6.1.4.1.4491.2.1.21.1.2.1.10
This attribute specifies the maximum duration in seconds that resources remain unused on an active service flow before the CMTS signals that both the active and admitted parameter sets are null. The value 0 signifies an infinite amount of time. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, this attribute returns 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ParamSetAdmittedTimeout		1.3.6.1.4.1.4491.2.1.21.1.2.1.11
This attribute specifies the maximum duration in seconds that resources remain in admitted state before resources must be released. The value of 0 signifies an infinite amount of time. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, this attribute returns 200.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ParamSetMaxConcatBurst		1.3.6.1.4.1.4491.2.1.21.1.2.1.12
This attribute specifies the maximum concatenated burst in bytes that an upstream Service Flow is allowed. The value is calculated from the FC byte of the Concatenation MAC Header to the last CRC byte of the last concatenated MAC frame, inclusive. The value of 0 specifies no maximum burst. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, this attribute returns the value of 1522 for scheduling types 'bestEffort', 'nonRealTimePollingService', and 'realTimePollingService'. If the parameter is not applicable, it is reported as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ParamSetSchedulingType		1.3.6.1.4.1.4491.2.1.21.1.2.1.13
This attribute specifies the upstream scheduling service used for upstream Service Flow. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set of an upstream Service Flow, this attribute returns the value of 'bestEffort'. For QOS parameter sets of downstream Service Flows, this attribute's value is reported as 'undefined'.
Status: current	Access: read-only
OBJECT-TYPE
	SchedulingType

docsQos3ParamSetNomPollInterval		1.3.6.1.4.1.4491.2.1.21.1.2.1.14
This attribute specifies the nominal interval in microseconds between successive unicast request opportunities on an upstream Service Flow. This attribute applies only to upstream Service Flows with SchedulingType of value 'nonRealTimePollingService', 'realTimePollingService', and 'unsolictedGrantServiceWithAD'. The parameter is mandatory for 'realTimePollingService'. If the parameter is omitted with 'nonRealTimePollingService', the CMTS uses an implementation-dependent value. If the parameter is omitted with 'unsolictedGrantServiceWithAD(5)' the CMTS uses the value of the Nominal Grant Interval parameter. In all cases, the CMTS reports the value it is using when the parameter is applicable. The CM reports the signaled parameter value if it was signaled. Otherwise, it returns 0. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this attribute's value as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

docsQos3ParamSetTolPollJitter		1.3.6.1.4.1.4491.2.1.21.1.2.1.15
This attribute specifies the maximum amount of time in microseconds that the unicast request interval may be delayed from the nominal periodic schedule on an upstream Service Flow. This parameter is applicable only to upstream Service Flows with a SchedulingType of 'realTimePollingService' or 'unsolictedGrantServiceWithAD'. If the referenced parameter is applicable but not present in the corresponding DOCSIS QOS Parameter Set, the CMTS uses an implementation-dependent value and reports the value it is using. The CM reports a value of 0 in this case. If the parameter is not applicable to the direction or upstream scheduling type of the Service Flow, both CMTS and CM report this attribute's value as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

docsQos3ParamSetUnsolicitGrantSize		1.3.6.1.4.1.4491.2.1.21.1.2.1.16
This attribute specifies the unsolicited grant size in bytes. The grant size includes the entire MAC frame data PDU from the Frame Control byte to the end of the MAC frame. The referenced parameter is applicable only for upstream flows with a SchedulingType of 'unsolicitedGrantServicewithAD' or 'unsolicitedGrantService', and it is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this attribute's value as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ParamSetNomGrantInterval		1.3.6.1.4.1.4491.2.1.21.1.2.1.17
This attribute specifies the nominal interval in microseconds between successive data grant opportunities on an upstream Service Flow. The referenced parameter is applicable only for upstream flows with a SchedulingType of 'unsolicitedGrantServicewithAD' or 'unsolicitedGrantService(6)', and it is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this attribute's value as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

docsQos3ParamSetTolGrantJitter		1.3.6.1.4.1.4491.2.1.21.1.2.1.18
This attribute specifies the maximum amount of time in microseconds that the transmission opportunities may be delayed from the nominal periodic schedule. The referenced parameter is applicable only for upstream flows with a SchedulingType of 'unsolicitedGrantServicewithAD' or 'unsolicitedGrantService(6)', and it is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this attribute's value as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

docsQos3ParamSetGrantsPerInterval		1.3.6.1.4.1.4491.2.1.21.1.2.1.19
This attribute specifies the number of data grants per Nominal Grant Interval (NomGrantInterval). The referenced parameter is applicable only for upstream flows with a SchedulingType of 'unsolicitedGrantServicewithAD' or 'unsolicitedGrantService', and it is mandatory when applicable. Both CMTS and CM report the signaled value of the parameter in this case. If the referenced parameter is not applicable to the direction or scheduling type of the corresponding DOCSIS QOS Parameter Set, both CMTS and CM report this attribute's value as 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..127

docsQos3ParamSetTosAndMask		1.3.6.1.4.1.4491.2.1.21.1.2.1.20
This attribute specifies the AND mask for the IP TOS byte for overwriting an IPv4 packet's TOS value or IPv6 packet's Traffic Class value. The IP packet TOS byte is bitwise ANDed with TosAndMask, then the result is bitwise ORed with TosORMask and the result is written to the IP packet TOS byte. A value of 'FF'H for TosAndMask and a value of '00'H for TosOrMask means that the IP Packet TOS byte is not overwritten. This combination is reported if the referenced parameter is not present in a QOS Parameter Set. The IP TOS octet as originally defined in RFC 791 has been superseded by the 6-bit Differentiated Services Field (DSField, RFC 3260) and the 2-bit Explicit Congestion Notification Field (ECN field, RFC 3168). The IPv6 Traffic Class octet RFC 2460 is consistent with that new definition. Network operators SHOULD avoid specifying values of TosAndMask and TosORMask that would result in the modification of the ECN bits. In particular, operators should not use values of TosAndMask that have either of the least-significant two bits set to 0. Similarly, operators should not use values of TosORMask that have either of the least-significant two bits set to 1. Even though this attribute is only enforced by the CMTS, the CM reports the value as signaled in the referenced parameter.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

docsQos3ParamSetTosOrMask		1.3.6.1.4.1.4491.2.1.21.1.2.1.21
This attribute specifies the OR mask for the IPv4 TOS value or IPv6 Traffic Class value. See the description of TosAndMask for further details. The IP TOS octet, as originally defined in RFC 791 has been superseded by the 6-bit Differentiated Services Field (DSField, RFC 3260) and the 2-bit Explicit Congestion Notification Field (ECN field, RFC 3168). The IPv6 Traffic Class octet RFC 2460 is consistent with that new definition. Network operators SHOULD avoid specifying values of TosAndMask and TosORMask that would result in the modification of the ECN bits.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1)

docsQos3ParamSetMaxLatency		1.3.6.1.4.1.4491.2.1.21.1.2.1.22
This attribute specifies the maximum latency between the reception of a packet by the CMTS on its NSI and the forwarding of the packet to the RF interface. A value of 0 signifies no maximum latency is enforced. This attribute only applies to downstream Service Flows. If the referenced parameter is not present in the corresponding downstream DOCSIS QOS Parameter Set, this attribute returns 0. This parameter is not applicable to upstream DOCSIS QOS Parameter Sets, so its value is reported as 0 in that case.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

docsQos3ParamSetType		1.3.6.1.4.1.4491.2.1.21.1.2.1.23
This key represents the QoS Parameter Set Type of the Service Flow. The following values are defined: 'active' Indicates the Active QOS parameter set, describing the service currently being provided by the DOCSIS MAC domain to the service flow. 'admitted' Indicates the Admitted QOS Parameter Set, describing services reserved by the DOCSIS MAC domain for use by the service flow. 'provisioned' Indicates the QOS Parameter Set defined in the DOCSIS CM Configuration file for the service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	active(1), admitted(2), provisioned(3)

docsQos3ParamSetRequestPolicyOct		1.3.6.1.4.1.4491.2.1.21.1.2.1.24
This attribute specifies which transmit interval opportunities the CM omits for upstream transmission requests and packet transmissions. This object takes its default value for downstream Service Flows. Unless otherwise indicated, a bit value of 1 means that a CM must not use that opportunity for upstream transmission. The format of this string enumerated the bits from 0 to 31 from left to right, for example bit 0 corresponds to the left most bit of the fourth octet. (octets numbered from right to left). The bit positions are defined as follows: 'broadcastReqOpp' all CMs broadcast request opportunities 'priorityReqMulticastReq' priority request multicast request opportunities 'reqDataForReq' request/data opportunities for requests 'reqDataForData' request/data opportunities for data 'piggybackReqWithData' piggyback requests with data 'concatenateData' concatenate data 'fragmentData' fragment data 'suppressPayloadHeaders' suppress payload headers 'dropPktsExceedUGSize' A value of 1 means that the service flow must drop packets that do not fit in the Unsolicited Grant size. If the referenced parameter is not present in a QOS Parameter Set, the value of this object is reported as '00000000'H.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(4)

docsQos3ParamSetBitMap		1.3.6.1.4.1.4491.2.1.21.1.2.1.25
This attribute indicates the set of QOS Parameter Set parameters actually signaled in the DOCSIS registration or dynamic service request message that created or modified the QOS Parameter Set. A bit is set to 1 when the associated parameter is present in the original request as follows: 'trafficPriority' Traffic Priority 'maxTrafficRate' Maximum Sustained Traffic Rate 'maxTrafficBurst' Maximum Traffic Burst 'minReservedRate' Minimum Reserved Traffic Rate 'minReservedPkt' Assumed Minimum Reserved Rate Packet Size 'activeTimeout' Timeout for Active QoS Parameters 'admittedTimeout' Timeout for Admitted QoS Parameters 'maxConcatBurst' Maximum Concatenated Burst 'schedulingType' Service Flow Scheduling Type 'requestPolicy' Request/Transmission Policy 'nomPollInterval' Nominal Polling Interval 'tolPollJitter' Tolerated Poll Jitter 'unsolicitGrantSize' Unsolicited Grant Size 'nomGrantInterval' Nominal Grant Interval 'tolGrantJitter' Tolerated Grant Jitter 'grantsPerInterval' Grants per Interval 'tosOverwrite' IP Type of Service (DSCP) Overwrite 'maxLatency' Maximum Downstream Latency 'requiredAttrMask' Service Flow Required Attribute Mask 'forbiddenAttrMask Service Flow Forbidden Attribute Mask 'attrAggrMask' Service Flow Attribute Aggregation Mask 'applicationId' Application Identifier 'multipCntnReqWindow' Multiplier to Contention Request Backoff Window 'multipBytesReq' Multiplier to Number of Bytes Requested 'maxReqPerSidCluster' Maximum Requests per SID Cluster 'maxOutstandingBytesPerSidCluster' Maximum Outstanding Bytes per SID Cluster 'maxTotalBytesReqPerSidCluster' Maximum Total Bytes Requested per SID Cluster 'maximumTimeInSidCluster' Maximum Time in the SID Cluster 'peakTrafficRate' Downstream Peak Traffic Rate 'dsResequencing' Downstream Resequencing Note that when Service Class names are expanded, the registration or dynamic response message may contain parameters expanded by the CMTS based on a stored service class. These expanded parameters are not indicated by a 1 bit in this attribute. Note that even though some QOS Parameter Set parameters may not be signaled in a message (so that the parameter's bit in this object is 0), the DOCSIS specification requires that default values be used. These default values are reported as the corresponding attribute.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	trafficPriority(0), maxTrafficRate(1), maxTrafficBurst(2), minReservedRate(3), minReservedPkt(4), activeTimeout(5), admittedTimeout(6), maxConcatBurst(7), schedulingType(8), requestPolicy(9), nomPollInterval(10), tolPollJitter(11), unsolicitGrantSize(12), nomGrantInterval(13), tolGrantJitter(14), grantsPerInterval(15), tosOverwrite(16), maxLatency(17), requiredAttrMask(18), forbiddenAttrMask(19), attrAggrMask(20), applicationId(21), multipCntnReqWindow(22), multipBytesReq(23), maxReqPerSidCluster(24), maxOutstandingBytesPerSidCluster(25), maxTotalBytesReqPerSidCluster(26), maximumTimeInSidCluster(27), peakTrafficRate(28), dsResequencing(29)

docsQos3ParamSetServiceFlowId		1.3.6.1.4.1.4491.2.1.21.1.2.1.26
This key represents the Service Flow ID for the service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..4294967295

docsQos3ParamSetRequiredAttrMask		1.3.6.1.4.1.4491.2.1.21.1.2.1.27
This attribute specifies the Required Attribute Mask to compare with the Provisioned Required Attributes when selecting the bonding groups for the service flow. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, this attribute returns '00000000'H.
Status: current	Access: read-only
OBJECT-TYPE
	AttributeMask

docsQos3ParamSetForbiddenAttrMask		1.3.6.1.4.1.4491.2.1.21.1.2.1.28
This attribute specifies the Forbidden Attribute Mask to compare with the Provisioned Forbidden Attributes when selecting the bonding groups for the service flow. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, this attribute returns '00000000'H.
Status: current	Access: read-only
OBJECT-TYPE
	AttributeMask

docsQos3ParamSetAttrAggrRuleMask		1.3.6.1.4.1.4491.2.1.21.1.2.1.29
This attribute specifies the Attribute Aggregation Mask to compare the Service Flow Required and Forbidden Attributes with the CMTS dynamically-created bonding group when selecting the bonding groups for the service flow. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, this attribute returns '00000000'H.
Status: current	Access: read-only
OBJECT-TYPE
	AttrAggrRuleMask

docsQos3ParamSetAppId		1.3.6.1.4.1.4491.2.1.21.1.2.1.30
This attribute represents the Application Identifier associated with the service flow for purposes beyond the scope of this specification. If the referenced parameter is not present in the corresponding DOCSIS QOS Parameter Set, this attribute returns 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

docsQos3ParamSetMultiplierContentionReqWindow		1.3.6.1.4.1.4491.2.1.21.1.2.1.31
This attribute specifies the multiplier to be applied by a CM when performing contention request backoff for data requests. This attribute only applies to upstream Service Flows in 3.0 operation. If the referenced parameter is not present in the upstream DOCSIS QOS Parameter Set or is not applicable, this attribute returns 8.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	4..12

docsQos3ParamSetMultiplierBytesReq		1.3.6.1.4.1.4491.2.1.21.1.2.1.32
This attribute specifies the assumed bandwidth request multiplier. This attribute only applies to upstream Service Flows in 3.0 operation. If the referenced parameter is not present in the upstream DOCSIS QOS Parameter Set, or is not applicable, this attribute returns 4.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1 \| 2 \| 4 \| 8 \| 16

docsQos3ParamSetMaxReqPerSidCluster		1.3.6.1.4.1.4491.2.1.21.1.2.1.33
This attribute specifies the maximum number of requests that a CM can make within a given SID Cluster before it must switch to a different SID Cluster to make further requests. A value of 0 indicates there is no limit. This attribute only applies to upstream Service Flows in 3.0 operation, in other cases it is reported as 0. If the referenced parameter is not present in the DOCSIS QOS Parameter Set, this attribute returns 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

docsQos3ParamSetMaxOutstandingBytesPerSidCluster		1.3.6.1.4.1.4491.2.1.21.1.2.1.34
This attribute specifies the maximum number of bytes for which a CM can have requests outstanding on a given SID Cluster. If defined number of bytes are outstanding and further requests are required, the CM must switch to a different SID Cluster if one is available. A value of 0 indicates there is no limit. This attribute only applies to upstream Service Flows in 3.0 operation, in other cases it is reported as 0. If the referenced parameter is not present in the DOCSIS QOS Parameter Set, this attribute returns 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

docsQos3ParamSetMaxTotBytesReqPerSidCluster		1.3.6.1.4.1.4491.2.1.21.1.2.1.35
This attribute specifies the maximum total number of bytes a CM can have requested using a given SID Cluster before it must switch to a different SID Cluster to make further requests. A value of 0 indicates there is no limit. This attribute only applies to upstream Service Flows in 3.0 operation, in other cases it is reported as 0. If the referenced parameter is not present in the DOCSIS QOS Parameter Set, this attribute returns 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

docsQos3ParamSetMaxTimeInSidCluster		1.3.6.1.4.1.4491.2.1.21.1.2.1.36
This attribute specifies the maximum time in milliseconds that a CM may use a particular SID Cluster before it must switch to a different SID Cluster to make further requests. A value of 0 indicates there is no limit. This attribute only applies to upstream Service Flows in 3.0 operation, in other cases it is reported as 0. If the referenced parameter is not present in the DOCSIS QOS Parameter Set, this attribute returns 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ParamSetPeakTrafficRate		1.3.6.1.4.1.4491.2.1.21.1.2.1.37
This attribute specifies the rate parameter 'P' of a token-bucket-based peak rate limiter for packets of a downstream service flow. A value of 0 signifies no Downstream Peak Traffic Rate is enforced. This attribute only applies to downstream Service Flows. If the referenced parameter is not present in the corresponding downstream DOCSIS QOS Parameter Set, this attribute returns 0. This parameter is not applicable to upstream DOCSIS QOS Parameter Sets, so its value is reported as 0 in that case.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

docsQos3ParamSetDsResequencing		1.3.6.1.4.1.4491.2.1.21.1.2.1.38
This attribute specifies if a resequending DSID need to be allocated to the service flow. The value 'resequencingDsid' indicates that a resequencing DSID is required if the service flow is assigned to a downstream bonding group. The value 'noResequencingDsid' indicates no resequencing DSID is associated with the service flow. This attribute only applies to downstream Service Flows in 3.0 operation. If the referenced parameter is not present in the corresponding downstream DOCSIS QOS Parameter Set, this attribute returns 0. This parameter is not applicable to upstream DOCSIS QOS Parameter Sets, so its value is reported as 0 in that case.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	resequencingDsid(0), noResequencingDsid(1)

docsQos3ServiceFlowTable		1.3.6.1.4.1.4491.2.1.21.1.3
This object describes the set of DOCSIS-QOS Service Flows in a managed device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3ServiceFlowEntry

docsQos3ServiceFlowEntry		1.3.6.1.4.1.4491.2.1.21.1.3.1
The conceptual row of docsQos3ServiceFlowTable. The ifIndex key corresponds to the MAC Domain interface of this service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3ServiceFlowEntry

docsQos3ServiceFlowId		1.3.6.1.4.1.4491.2.1.21.1.3.1.1
This key represents an identifier assigned to a Service Flow by CMTS within a MAC Domain. The value 0 is used only for the purpose of reporting instances of the PktClass object pertaining UDCs and not used for association of QOS classifiers to service flows.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

docsQos3ServiceFlowSID		1.3.6.1.4.1.4491.2.1.21.1.3.1.6
Service Identifier (SID) assigned to an admitted or active Service Flow. This attribute reports a value of 0 if a Service ID is not associated with the Service Flow. Only active or admitted upstream Service Flows will have a Service ID (SID).
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..16383

docsQos3ServiceFlowDirection		1.3.6.1.4.1.4491.2.1.21.1.3.1.7
This attribute represents the direction of the Service Flow.
Status: current	Access: read-only
OBJECT-TYPE
	IfDirection

docsQos3ServiceFlowPrimary		1.3.6.1.4.1.4491.2.1.21.1.3.1.8
This attribute reflects whether Service Flow is the primary or a secondary Service Flow.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

docsQos3ServiceFlowParamSetTypeStatus		1.3.6.1.4.1.4491.2.1.21.1.3.1.9
This attribute represents the status of the service flow based on the admission state. 'active' bit set to '1' indicates that the service flow is active and that the corresponding QOS ParamSet is stored in the CMTS. 'admitted' bit set to '1' indicates that the service flow resources were reserved and that the corresponding QOS ParamSet is stored in the CMTS. 'provisioned' bit set to '1' indicates that the service flow was defined in the CM config file and that the corresponding QOS ParamSet is stored in the CMTS.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	active(0), admitted(1), provisioned(2)

docsQos3ServiceFlowChSetId		1.3.6.1.4.1.4491.2.1.21.1.3.1.10
This attribute represents the Channel Set Id associated with the service flow.
Status: current	Access: read-only
OBJECT-TYPE
	ChSetId

docsQos3ServiceFlowAttrAssignSuccess		1.3.6.1.4.1.4491.2.1.21.1.3.1.11
If set to 'true', this attribute indicates that the current channel set associated with the service flow meets the Required and Forbidden Attribute Mask encodings.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

docsQos3ServiceFlowDsid		1.3.6.1.4.1.4491.2.1.21.1.3.1.12
This attribute indicates the DSID associated with the downstream service flow. downstream service flows without a DSID or upstream Service Flows report the value zero.
Status: current	Access: read-only
OBJECT-TYPE
	Dsid

docsQos3ServiceFlowStatsTable		1.3.6.1.4.1.4491.2.1.21.1.4
This object describes statistics associated with the Service Flows in a managed device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3ServiceFlowStatsEntry

docsQos3ServiceFlowStatsEntry		1.3.6.1.4.1.4491.2.1.21.1.4.1
The conceptual row of docsQos3ServiceFlowStatsTable. The ifIndex key corresponds to the MAC Domain interface of the service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3ServiceFlowStatsEntry

docsQos3ServiceFlowPkts		1.3.6.1.4.1.4491.2.1.21.1.4.1.1
For outgoing Service Flows, this attribute counts the number of Packet Data PDUs forwarded to this Service Flow. For incoming upstream CMTS service flows, this attribute counts the number of Packet Data PDUs actually received on the Service Flow identified by the SID for which the packet was scheduled. CMs not classifying downstream packets may report this attribute's value as 0 for downstream Service Flows. This attribute does not count MAC-specific management messages. Particularly for UGS flows, packets sent on the primary Service Flow in violation of the UGS grant size should be counted only by the instance of this attribute that is associated with the primary service flow. Unclassified upstream user data packets (i.e., non- MAC-management) forwarded to the primary upstream Service Flow should be counted by the instance of this attribute that is associated with the primary service flow. This attribute does include packets counted by ServiceFlowPolicedDelayPkts, but does not include packets counted by ServiceFlowPolicedDropPkts and ServiceFlowPHSUnknowns. This counter's last discontinuity is the ifCounterDiscontinuityTime for of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

docsQos3ServiceFlowOctets		1.3.6.1.4.1.4491.2.1.21.1.4.1.2
This attribute indicates the count of the number of octets from the byte after the MAC header HCS to the end of the CRC for all packets counted in the ServiceFlowPkts attribute for this row. Note that this counts the octets after payload header suppression and before payload header expansion have been applied. This counter's last discontinuity is the ifCounterDiscontinuityTime for of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

docsQos3ServiceFlowTimeCreated		1.3.6.1.4.1.4491.2.1.21.1.4.1.3
This attribute indicates the value of sysUpTime when the service flow was created.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

docsQos3ServiceFlowTimeActive		1.3.6.1.4.1.4491.2.1.21.1.4.1.4
This attribute indicates the number of seconds that the service flow has been active. This counter's last discontinuity is the ifCounterDiscontinuityTime for of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3ServiceFlowPHSUnknowns		1.3.6.1.4.1.4491.2.1.21.1.4.1.5
For incoming upstream CMTS service flows, this attribute counts the number of packets received with an unknown payload header suppression index. The service flow is identified by the SID for which the packet was scheduled. On a CM, only this attribute's instance for the primary downstream service flow counts packets received with an unknown payload header suppression index. All other downstream service flows on CM report this attributes value as 0. All outgoing service flows report this attribute's value as 0. This counter's last discontinuity is the ifCounterDiscontinuityTime for of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3ServiceFlowPolicedDropPkts		1.3.6.1.4.1.4491.2.1.21.1.4.1.6
For outgoing service flows, this attribute counts the number of Packet Data PDUs classified to this service flow dropped due to: (1) implementation-dependent excessive delay while enforcing the Maximum Sustained Traffic Rate; or (2) UGS packets dropped due to exceeding the Unsolicited Grant Size with a Request/Transmission policy that requires such packets to be dropped. Classified packets dropped due to other reasons must be counted in ifOutDiscards for the interface of this service flow. This attribute reports 0 for incoming service flows. This counter's last discontinuity is the ifCounterDiscontinuityTime for of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3ServiceFlowPolicedDelayPkts		1.3.6.1.4.1.4491.2.1.21.1.4.1.7
This attribute counts only outgoing packets delayed in order to maintain the Maximum Sustained Traffic Rate. This attribute will always report a value of 0 for UGS flows because the Maximum Sustained Traffic Rate does not apply. This attribute is 0 for incoming service flows. This counter's last discontinuity is the ifCounterDiscontinuityTime for of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3UpstreamStatsTable		1.3.6.1.4.1.4491.2.1.21.1.5
This object describes statistics associated with upstream service flows. All counted frames must be received without a Frame Check Sequence (FCS) error.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3UpstreamStatsEntry

docsQos3UpstreamStatsEntry		1.3.6.1.4.1.4491.2.1.21.1.5.1
The conceptual row of docsQos3UpstreamStatsTable. The ifIndex key corresponds to the upstream logical channel interface of the service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3UpstreamStatsEntry

docsQos3SID		1.3.6.1.4.1.4491.2.1.21.1.5.1.1
This key identifies a service ID for an admitted or active upstream service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..16383

docsQos3UpstreamFragments		1.3.6.1.4.1.4491.2.1.21.1.5.1.2
This attribure indicates the number of fragmentation headers received on an upstream service flow, regardless of whether the fragment was correctly reassembled into a valid packet. This counter's last discontinuity is the ifCounterDiscontinuityTime for of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3UpstreamFragDiscards		1.3.6.1.4.1.4491.2.1.21.1.5.1.3
This attribute indicates the number of upstream fragments discarded and not assembled into a valid upstream packet. This counter's last discontinuity is the ifCounterDiscontinuityTime for of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3UpstreamConcatBursts		1.3.6.1.4.1.4491.2.1.21.1.5.1.4
This attribute indicates the number of concatenation headers received on an upstream service flow. This counter's last discontinuity is the ifCounterDiscontinuityTime for of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DynamicServiceStatsTable		1.3.6.1.4.1.4491.2.1.21.1.6
This object describes statistics associated with the Dynamic Service Flows, Dynamic Channel Changes and Dynamic Bonding Changes in a managed device within a MAC Domain. For each MAC Domain there are two instances for the for the upstream and downstream direction. On the CMTS, the downstream direction instance indicates messages transmitted or transactions originated by the CMTS. The upstream direction intance indicates messages received or transaction originated by the CM. On the CM, the downstream direction instance indicates messages received or transactions originated by the CMTS. The upstream direction instance indicates messages transmitted by the CM or transactions originated by the CM.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3DynamicServiceStatsEntry

docsQos3DynamicServiceStatsEntry		1.3.6.1.4.1.4491.2.1.21.1.6.1
The conceptual row of docsQos3DynamicServiceStatsTable. The ifIndex key corresponds to the MAC Domain interface of the service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3DynamicServiceStatsEntry

docsQos3IfDirection		1.3.6.1.4.1.4491.2.1.21.1.6.1.1
This attribute indicates the interface direction for the instance the statistics are collected.
Status: current	Access: not-accessible
OBJECT-TYPE
	IfDirection

docsQos3DSAReqs		1.3.6.1.4.1.4491.2.1.21.1.6.1.2
This attribute indicates the number of Dynamic Service Addition Requests, including retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DSARsps		1.3.6.1.4.1.4491.2.1.21.1.6.1.3
The number of Dynamic Service Addition Responses, including retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DSAAcks		1.3.6.1.4.1.4491.2.1.21.1.6.1.4
The number of Dynamic Service Addition Acknowledgements, including retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DSCReqs		1.3.6.1.4.1.4491.2.1.21.1.6.1.5
The number of Dynamic Service Change Requests, including retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DSCRsps		1.3.6.1.4.1.4491.2.1.21.1.6.1.6
The number of Dynamic Service Change Responses, including retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DSCAcks		1.3.6.1.4.1.4491.2.1.21.1.6.1.7
The number of Dynamic Service Change Acknowledgements, including retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DSDReqs		1.3.6.1.4.1.4491.2.1.21.1.6.1.8
The number of Dynamic Service Delete Requests, including retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DSDRsps		1.3.6.1.4.1.4491.2.1.21.1.6.1.9
The number of Dynamic Service Delete Responses, including retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DynamicAdds		1.3.6.1.4.1.4491.2.1.21.1.6.1.10
The number of successful Dynamic Service Addition transactions. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DynamicAddFails		1.3.6.1.4.1.4491.2.1.21.1.6.1.11
The number of failed Dynamic Service Addition transactions. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DynamicChanges		1.3.6.1.4.1.4491.2.1.21.1.6.1.12
The number of successful Dynamic Service Change transactions. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DynamicChangeFails		1.3.6.1.4.1.4491.2.1.21.1.6.1.13
The number of failed Dynamic Service Change transactions. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DynamicDeletes		1.3.6.1.4.1.4491.2.1.21.1.6.1.14
The number of successful Dynamic Service Delete transactions. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DynamicDeleteFails		1.3.6.1.4.1.4491.2.1.21.1.6.1.15
The number of failed Dynamic Service Delete transactions. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DCCReqs		1.3.6.1.4.1.4491.2.1.21.1.6.1.16
The number of Dynamic Channel Change Request messages traversing an interface. This count is nonzero only on downstream direction rows. This count should include the number of retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DCCRsps		1.3.6.1.4.1.4491.2.1.21.1.6.1.17
The number of Dynamic Channel Change Response messages traversing an interface. This count is nonzero only on upstream direction rows. This count should include the number of retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DCCAcks		1.3.6.1.4.1.4491.2.1.21.1.6.1.18
The number of Dynamic Channel Change Acknowledgement messages traversing an interface. This count is nonzero only on downstream direction rows. This count should include the number of retries. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DCCs		1.3.6.1.4.1.4491.2.1.21.1.6.1.19
The number of successful Dynamic Channel Change transactions. This count is nonzero only on downstream direction rows. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DCCFails		1.3.6.1.4.1.4491.2.1.21.1.6.1.20
The number of failed Dynamic Channel Change transactions. This count is nonzero only on downstream direction rows. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DCCRspDeparts		1.3.6.1.4.1.4491.2.1.21.1.6.1.21
This attribute contains the number of Dynamic Channel Change Response (depart) messages. It only applies to upstream direction. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DCCRspArrives		1.3.6.1.4.1.4491.2.1.21.1.6.1.22
This attribute contains the number of Dynamic Channel Change Response (arrive) messages and should include retries. It only applies to the upstream direction. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DbcReqs		1.3.6.1.4.1.4491.2.1.21.1.6.1.23
This attribute contains the number of Dynamic Bonding Change Requests, including retries. It only applies to the upstream direction. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DbcRsps		1.3.6.1.4.1.4491.2.1.21.1.6.1.24
This attribute contains the number of Dynamic Bonding Change Responses, including retries. It only applies to the upstream direction. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DbcAcks		1.3.6.1.4.1.4491.2.1.21.1.6.1.25
This attribute contains the number of Dynamic Bonding Change Acknowledgements, including retries. It only applies to the downstream direction. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DbcSuccesses		1.3.6.1.4.1.4491.2.1.21.1.6.1.26
This attribute contains the number of fully successful Dynamic Bonding Change transactions. It only applies to the downstream direction and does not include DBC transactions that result in Partial Service. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DbcFails		1.3.6.1.4.1.4491.2.1.21.1.6.1.27
This attribute contains the number of failed Dynamic Bonding Change transactions. It only applies to the downstream direction. Note that Partial Service is not considered a failed transaction. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3DbcPartial		1.3.6.1.4.1.4491.2.1.21.1.6.1.28
This attribute contains the number of unsuccessful Dynamic Bonding Change transactions that result in Partial Service. IT only applies to the downstream direction. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3ServiceFlowLogTable		1.3.6.1.4.1.4491.2.1.21.1.7
This object contains a log of the disconnected Service Flows in a managed device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3ServiceFlowLogEntry

docsQos3ServiceFlowLogEntry		1.3.6.1.4.1.4491.2.1.21.1.7.1
The conceptual row of docsQos3ServiceFlowLogTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3ServiceFlowLogEntry

docsQos3ServiceFlowLogIndex		1.3.6.1.4.1.4491.2.1.21.1.7.1.1
This key indicates an unique index for a logged service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..4294967295

docsQos3ServiceFlowLogIfIndex		1.3.6.1.4.1.4491.2.1.21.1.7.1.2
This attribute indicates the MAC Domain Interface index where the service flow was present.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

docsQos3ServiceFlowLogSFID		1.3.6.1.4.1.4491.2.1.21.1.7.1.3
This attribute indicates the identifier assigned to the service flow.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

docsQos3ServiceFlowLogCmMac		1.3.6.1.4.1.4491.2.1.21.1.7.1.4
This attribute indicates the MAC address of the cable modem associated with the service flow.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

docsQos3ServiceFlowLogPkts		1.3.6.1.4.1.4491.2.1.21.1.7.1.5
This attribute indicates the final value of the Pkts attribute in the ServiceFlowStats object for the service flow.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

docsQos3ServiceFlowLogOctets		1.3.6.1.4.1.4491.2.1.21.1.7.1.6
This attribute indicates the final value of the Pkts attribute in the ServiceFlowStats object for the service flow.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

docsQos3ServiceFlowLogTimeDeleted		1.3.6.1.4.1.4491.2.1.21.1.7.1.7
This attribute indicates the value of sysUpTime when the service flow was deleted.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

docsQos3ServiceFlowLogTimeCreated		1.3.6.1.4.1.4491.2.1.21.1.7.1.8
This attribute indicates the value of sysUpTime when the service flow was created.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

docsQos3ServiceFlowLogTimeActive		1.3.6.1.4.1.4491.2.1.21.1.7.1.9
This attribute indicates the total time that the service flow was active.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3ServiceFlowLogDirection		1.3.6.1.4.1.4491.2.1.21.1.7.1.11
This attribute indicates the value of Service Flow direction for the service flow.
Status: current	Access: read-only
OBJECT-TYPE
	IfDirection

docsQos3ServiceFlowLogPrimary		1.3.6.1.4.1.4491.2.1.21.1.7.1.12
If set to 'true', this attribute indicates that the Service Flow in the log was a Primary Service Flow, otherwise, a Secondary Service Flow.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

docsQos3ServiceFlowLogServiceClassName		1.3.6.1.4.1.4491.2.1.21.1.7.1.13
This attribute indicates the value of ServiceClassName for the provisioned QOS Parameter Set of the service flow.
Status: current	Access: read-only
OBJECT-TYPE
	SnmpAdminString	Size(0..15)

docsQos3ServiceFlowLogPolicedDropPkts		1.3.6.1.4.1.4491.2.1.21.1.7.1.14
This attribute indicates the final value of PolicedDropPkts attribute of the ServiceFlowStats object for the service flow.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3ServiceFlowLogPolicedDelayPkts		1.3.6.1.4.1.4491.2.1.21.1.7.1.15
This attribute indicates the final value of PolicedDelayPkts attribute of the ServiceFlowStats object for the service flow.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3ServiceFlowLogControl		1.3.6.1.4.1.4491.2.1.21.1.7.1.16
This attribute when set to 'destroy' removes this instance from the object. Reading this attribute returns the value 'active'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), destroy(6)

docsQos3ServiceClassTable		1.3.6.1.4.1.4491.2.1.21.1.8
This object describes a provisioned service class on a CMTS. Each object instance defines a template for certain DOCSIS QOS Parameter Set values. When a CM creates or modifies an Admitted QOS Parameter Set for a Service Flow, it may reference a Service Class Name instead of providing explicit QOS Parameter Set values. In this case, the CMTS populates the QOS Parameter Set with the applicable corresponding values from the named Service Class. Subsequent changes to a Service Class row do not affect the QOS Parameter Set values of any service flows already admitted. A service class template applies to only a single direction, as indicated in the ServiceClassDirection attribute.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3ServiceClassEntry

docsQos3ServiceClassEntry		1.3.6.1.4.1.4491.2.1.21.1.8.1
The conceptual row of docsQos3ServiceClassTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3ServiceClassEntry

docsQos3ServiceClassName		1.3.6.1.4.1.4491.2.1.21.1.8.1.1
This key indicates the Service Class Name associated with this object instance. DOCSIS specifies that the maximum size is 16 ASCII characters including a terminating zero. The terminating zero is not represented in this SnmpAdminString syntax attribute.
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpAdminString	Size(1..15)

docsQos3ServiceClassStatus		1.3.6.1.4.1.4491.2.1.21.1.8.1.3
The conceptual row status of this object.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

docsQos3ServiceClassPriority		1.3.6.1.4.1.4491.2.1.21.1.8.1.4
This attribute is the template for the Priority attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

docsQos3ServiceClassMaxTrafficRate		1.3.6.1.4.1.4491.2.1.21.1.8.1.5
This attribute is the template for the MaxTrafficRate attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	DOCSQOS3BitRate

docsQos3ServiceClassMaxTrafficBurst		1.3.6.1.4.1.4491.2.1.21.1.8.1.6
This attribute is the template for the MaxTrafficBurst attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

docsQos3ServiceClassMinReservedRate		1.3.6.1.4.1.4491.2.1.21.1.8.1.7
This attribute is the template for the MinReservedRate attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	DOCSQOS3BitRate

docsQos3ServiceClassMinReservedPkt		1.3.6.1.4.1.4491.2.1.21.1.8.1.8
This attribute is the template for the MinReservedPkt attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ServiceClassMaxConcatBurst		1.3.6.1.4.1.4491.2.1.21.1.8.1.9
This attribute is the template for the MaxConcatBurst attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ServiceClassNomPollInterval		1.3.6.1.4.1.4491.2.1.21.1.8.1.10
This attribute is the template for the NomPollInterval attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

docsQos3ServiceClassTolPollJitter		1.3.6.1.4.1.4491.2.1.21.1.8.1.11
This attribute is the template for the TolPolJitter attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

docsQos3ServiceClassUnsolicitGrantSize		1.3.6.1.4.1.4491.2.1.21.1.8.1.12
This attribute is the template for the UnsolicitGrantSize attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ServiceClassNomGrantInterval		1.3.6.1.4.1.4491.2.1.21.1.8.1.13
This attribute is the template for the NomGrantInterval attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

docsQos3ServiceClassTolGrantJitter		1.3.6.1.4.1.4491.2.1.21.1.8.1.14
This attribute is the template for the TolGrantJitter attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

docsQos3ServiceClassGrantsPerInterval		1.3.6.1.4.1.4491.2.1.21.1.8.1.15
This attribute is the template for the GrantsPerInterval attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..127

docsQos3ServiceClassMaxLatency		1.3.6.1.4.1.4491.2.1.21.1.8.1.16
This attribute is the template for the MaxLatency attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

docsQos3ServiceClassActiveTimeout		1.3.6.1.4.1.4491.2.1.21.1.8.1.17
This attribute is the template for the ActiveTimeout attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ServiceClassAdmittedTimeout		1.3.6.1.4.1.4491.2.1.21.1.8.1.18
This attribute is the template for the AddmitedTimeout attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ServiceClassSchedulingType		1.3.6.1.4.1.4491.2.1.21.1.8.1.19
This attribute is the template for the SchedulingType attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	SchedulingType

docsQos3ServiceClassRequestPolicy		1.3.6.1.4.1.4491.2.1.21.1.8.1.20
This attribute is the template for the ReqPolicyOct attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(4)

docsQos3ServiceClassTosAndMask		1.3.6.1.4.1.4491.2.1.21.1.8.1.21
This attribute is the template for the TosAndMask attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(1)

docsQos3ServiceClassTosOrMask		1.3.6.1.4.1.4491.2.1.21.1.8.1.22
This attribute is the template for the TosOrMask attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING	Size(1)

docsQos3ServiceClassDirection		1.3.6.1.4.1.4491.2.1.21.1.8.1.23
This attribute is the template for the Direction attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	IfDirection

docsQos3ServiceClassStorageType		1.3.6.1.4.1.4491.2.1.21.1.8.1.24
This attribute defines whether this row is kept in volatile storage and lost upon reboot or whether it is backed up by non-volatile or permanent storage. 'permanent' entries need not allow writable access to any instance attribute.
Status: current	Access: read-create
OBJECT-TYPE
	StorageType

docsQos3ServiceClassDSCPOverwrite		1.3.6.1.4.1.4491.2.1.21.1.8.1.25
This attribute allows the overwrite of the DSCP field per RFC 3260. If this attribute is -1, then the corresponding TosAndMask value is set to be 'FF'H and TosOrMask is set to '00'H. Otherwise, this attribute is in the range of 0..63, and the corresponding TosAndMask value is '03'H and TosOrMaskvalue is this attribute value shifted left by two bit positions.
Status: current	Access: read-create
OBJECT-TYPE
	DscpOrAny

docsQos3ServiceClassRequiredAttrMask		1.3.6.1.4.1.4491.2.1.21.1.8.1.26
This attribute is the template for the RequiredAttrMask attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	AttributeMask

docsQos3ServiceClassForbiddenAttrMask		1.3.6.1.4.1.4491.2.1.21.1.8.1.27
This attribute is the template for the ForbiddenAttrMask attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	AttributeMask

docsQos3ServiceClassAttrAggrRuleMask		1.3.6.1.4.1.4491.2.1.21.1.8.1.28
This attribute is the template for the AttrAggregationMask attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	AttrAggrRuleMask

docsQos3ServiceClassAppId		1.3.6.1.4.1.4491.2.1.21.1.8.1.29
This attribute is the template for the AppId attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

docsQos3ServiceClassMultiplierContentionReqWindow		1.3.6.1.4.1.4491.2.1.21.1.8.1.30
This attribute is the template for the MultiplierContentionReqWindow attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	4..12

docsQos3ServiceClassMultiplierBytesReq		1.3.6.1.4.1.4491.2.1.21.1.8.1.31
This attribute is the template for the MultiplierBytesReq attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1 \| 2 \| 4 \| 8 \| 16

docsQos3ServiceClassMaxReqPerSidCluster		1.3.6.1.4.1.4491.2.1.21.1.8.1.32
This attribute is the template for the MaxReqPerSidCluster attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

docsQos3ServiceClassMaxOutstandingBytesPerSidCluster		1.3.6.1.4.1.4491.2.1.21.1.8.1.33
This attribute is the template for the MaxOutstandingBytesPerSidCluster attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

docsQos3ServiceClassMaxTotBytesReqPerSidCluster		1.3.6.1.4.1.4491.2.1.21.1.8.1.34
This attribute is the template for the MaxTotBytesReqPerSidCluster attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

docsQos3ServiceClassMaxTimeInSidCluster		1.3.6.1.4.1.4491.2.1.21.1.8.1.35
This attribute is the template for the MaxTimeInSidCluster attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3ServiceClassPeakTrafficRate		1.3.6.1.4.1.4491.2.1.21.1.8.1.36
This attribute is the template for the PeakTrafficRate attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

docsQos3ServiceClassDsResequencing		1.3.6.1.4.1.4491.2.1.21.1.8.1.37
This attribute is the template for the DsResequencing attribute of the QoS Parameter Set.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	resequencingDsid(0), noResequencingDsid(1)

docsQos3PHSTable		1.3.6.1.4.1.4491.2.1.21.1.10
This object describes the set of payload header suppression of Service Flows.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3PHSEntry

docsQos3PHSEntry		1.3.6.1.4.1.4491.2.1.21.1.10.1
The conceptual row of docsQos3PHSTable. The ifIndex key corresponds to the MAC Domain interface of the service flow of the classifier that includes this PHS rule.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3PHSEntry

docsQos3PHSField		1.3.6.1.4.1.4491.2.1.21.1.10.1.2
This attribute indicates the Payload Header suppression field defines the bytes of the header that must be suppressed/restored by the sending/receiving device. The number of octets in this attribute should be the same as the value of PHSSize.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..255)

docsQos3PHSMask		1.3.6.1.4.1.4491.2.1.21.1.10.1.3
This attribute defines the bit mask that is used in combination with the PHSField. It defines which bytes in the header must be suppressed/restored by the sending or receiving device. Each bit of this bit mask corresponds to a byte in the PHSField, with the least significant bit corresponding to the first byte of the PHSField. Each bit of the bit mask specifies whether the corresponding byte should be suppressed in the packet. A bit value of '1' indicates that the byte should be suppressed by the sending device and restored by the receiving device. A bit value of '0' indicates that the byte should not be suppressed by the sending device or restored by the receiving device. If the bit mask does not contain a bit for each byte in the PHSField, then the bit mask is extended with bit values of '1' to be the necessary length.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

docsQos3PHSSize		1.3.6.1.4.1.4491.2.1.21.1.10.1.4
This attribute specifies the number of bytes in the header to be suppressed and restored. The value of this attribute matches the numberof bytes in the Field attribute.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..255

docsQos3PHSVerify		1.3.6.1.4.1.4491.2.1.21.1.10.1.5
If 'true', this attribute indicates that the sender must verify that the PHS Field is the same as the content in the packet to be suppressed.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

docsQos3PHSIndex		1.3.6.1.4.1.4491.2.1.21.1.10.1.7
This attribute uniquely references the PHS rule for a given service flow.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..255

docsQos3CmtsMacToSrvFlowTable		1.3.6.1.4.1.4491.2.1.21.1.11
This object provides the mapping of unicast service flows with the cable modem the service flows belongs to.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3CmtsMacToSrvFlowEntry

docsQos3CmtsMacToSrvFlowEntry		1.3.6.1.4.1.4491.2.1.21.1.11.1
The conceptual row of docsQos3CmtsMacToSrvFlowTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3CmtsMacToSrvFlowEntry

docsQos3CmtsCmMac		1.3.6.1.4.1.4491.2.1.21.1.11.1.1
This key represents the MAC address for the referenced CM.
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAddress

docsQos3CmtsServiceFlowId		1.3.6.1.4.1.4491.2.1.21.1.11.1.2
This key represents the identifier of the Service Flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..4294967295

docsQos3CmtsIfIndex		1.3.6.1.4.1.4491.2.1.21.1.11.1.3
This attribute represents the interface index of the MAC domain of the Service Flow and where the CableModem is registered.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

docsQos3ServiceFlowSidClusterTable		1.3.6.1.4.1.4491.2.1.21.1.12
This object defines the SID clusters associated with an upstream service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3ServiceFlowSidClusterEntry

docsQos3ServiceFlowSidClusterEntry		1.3.6.1.4.1.4491.2.1.21.1.12.1
The conceptual row of docsQos3ServiceFlowSidClusterTable. The ifIndex key corresponds to the MAC Domain interface of the service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3ServiceFlowSidClusterEntry

docsQos3ServiceFlowSidClusterId		1.3.6.1.4.1.4491.2.1.21.1.12.1.1
This key represents the SID Cluster ID of the SID Cluster.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..7

docsQos3ServiceFlowSidClusterUcid		1.3.6.1.4.1.4491.2.1.21.1.12.1.2
This key represents the upstream Channel ID mapped to the corresponding SID.
Status: current	Access: not-accessible
OBJECT-TYPE
	ChId	1..255

docsQos3ServiceFlowSidClusterSid		1.3.6.1.4.1.4491.2.1.21.1.12.1.3
This attribute represents the SID assigned to the upstream channel in this SID Cluster.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..16383

docsQos3GrpServiceFlowTable		1.3.6.1.4.1.4491.2.1.21.1.13
This object provides extensions to the service flow information for Group Service Flows (GSFs).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3GrpServiceFlowEntry

docsQos3GrpServiceFlowEntry		1.3.6.1.4.1.4491.2.1.21.1.13.1
The conceptual row of docsQos3GrpServiceFlowTable. The ifIndex key corresponds to the MAC Domain interface of the group service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3GrpServiceFlowEntry

docsQos3GrpServiceFlowIsDef		1.3.6.1.4.1.4491.2.1.21.1.13.1.1
This attribute indicates whether the GSF QOS Parameter Set corresponds to the Default Group Service Flow.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

docsQos3GrpServiceFlowQosConfigId		1.3.6.1.4.1.4491.2.1.21.1.13.1.2
This attribute indicates the Group QoS Configuration (GQC) identifier used of the creation of this GSF. The value zero indicates that the Service Flow is using the default service flow.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3GrpServiceFlowNumSess		1.3.6.1.4.1.4491.2.1.21.1.13.1.3
This attribute indicates the number of sessions that are configured in an aggregated Service Flow. If this is a single session replication, the value of this attribute is 1.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..65535

docsQos3GrpPktClassTable		1.3.6.1.4.1.4491.2.1.21.1.14
This object provides additional packet classification information for Group Classifier References (GCRs) in a Group Service Flow (GSF).
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3GrpPktClassEntry

docsQos3GrpPktClassEntry		1.3.6.1.4.1.4491.2.1.21.1.14.1
The conceptual row of docsQos3GrpPktClassTable. The ifIndex key corresponds to the MAC Domain interface of the service flow of this group classifier.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3GrpPktClassEntry

docsQos3GrpPktClassGrpConfigId		1.3.6.1.4.1.4491.2.1.21.1.14.1.1
This attribute indicates the GC identifier used of the creation of this GSF.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..4294967295

docsQos3UpChCounterExtTable		1.3.6.1.4.1.4491.2.1.21.1.15
This object provides extensions for service flow statistics for fragmentation for channel bonding.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3UpChCounterExtEntry

docsQos3UpChCounterExtEntry		1.3.6.1.4.1.4491.2.1.21.1.15.1
The conceptual row of docsQos3UpChCounterExtTable. The ifIndex key corresponds to the upstream Channel Interface of the service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3UpChCounterExtEntry

docsQos3UpChCounterExtSgmtValids		1.3.6.1.4.1.4491.2.1.21.1.15.1.1
This attribute represents the total number segments processed on this channel. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3UpChCounterExtSgmtDiscards		1.3.6.1.4.1.4491.2.1.21.1.15.1.2
This attribute represents the total number of discarded segments on this channel due to segment HCS problems. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3ServiceFlowCcfStatsTable		1.3.6.1.4.1.4491.2.1.21.1.16
This object provides upstream service flow statistics for Continous Concatenation and Fragmentation (CCF). The CMTS MAY not instantate this object for service flows that do not use CCF or return the zero value on individual counter's statistics.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3ServiceFlowCcfStatsEntry

docsQos3ServiceFlowCcfStatsEntry		1.3.6.1.4.1.4491.2.1.21.1.16.1
The conceptual row of docsQos3ServiceFlowCcfStatsTable. The ifIndex key corresponds to the MAC Domain interface of the service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3ServiceFlowCcfStatsEntry

docsQos3ServiceFlowCcfStatsSgmtValids		1.3.6.1.4.1.4491.2.1.21.1.16.1.1
This attribute contains the number of segments counted on this service flow regardless of whether the fragment was correctly reassembled into valid packets. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3ServiceFlowCcfStatsSgmtLost		1.3.6.1.4.1.4491.2.1.21.1.16.1.2
This attribute counts the number of segments which the CMTS segment reassembly function determines were lost. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmServiceUsStatsTable		1.3.6.1.4.1.4491.2.1.21.1.17
This object defines DOCSIS MAC services primitive statistics of upstream service flows. In pre-3.0 DOCSIS devices this statistics exists per SID for either Cos or Qos services in the SNMP table docsIfCmServiceTable. A 3.0 CM with CoS configuration (DOCSIS 1.0 mode) reports the statistics defined in the SNMP table docsIfCmServiceTable. A 3.0 CM with QoS configuration reports this object regardless of whether Multiple Transmit Channel is enabled or disabled.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3CmServiceUsStatsEntry

docsQos3CmServiceUsStatsEntry		1.3.6.1.4.1.4491.2.1.21.1.17.1
The conceptual row of docsQos3CmServiceUsStatsTable. The ifIndex key corresponds to the MAC Domain interface of the service flow.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3CmServiceUsStatsEntry

docsQos3CmServiceUsStatsTxSlotsImmed		1.3.6.1.4.1.4491.2.1.21.1.17.1.1
This attribute contains the number of upstream mini-slots which have been used to transmit data PDUs in immediate (contention) mode. This includes only those PDUs that are presumed to have arrived at the head-end (i.e., those which were explicitly acknowledged.) It does not include retransmission attempts or mini-slots used by Requests. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmServiceUsStatsTxSlotsDed		1.3.6.1.4.1.4491.2.1.21.1.17.1.2
This attribute contains the number of upstream mini-slots which have been used to transmit data PDUs in dedicated mode (i.e., as a result of a unicast Data Grant). Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmServiceUsStatsTxRetries		1.3.6.1.4.1.4491.2.1.21.1.17.1.3
This attribute contains the number of attempts to transmit data PDUs containing requests for acknowledgment that did not result in acknowledgment. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime for the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmServiceUsStatsTxExceededs		1.3.6.1.4.1.4491.2.1.21.1.17.1.4
This attribute contains the number of attempts to transmit bandwidth requests which did not result in acknowledgment. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmServiceUsStatsRqRetries		1.3.6.1.4.1.4491.2.1.21.1.17.1.5
This attribute contains the number of attempts to transmit bandwidth requests which did not result in acknowledgment. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmServiceUsStatsRqExceededs		1.3.6.1.4.1.4491.2.1.21.1.17.1.6
This attribute contains the number of requests for bandwidth which failed due to excessive retries without acknowledgment. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmServiceUsStatsSgmts		1.3.6.1.4.1.4491.2.1.21.1.17.1.7
This attribute contains the number of segments sent on this service flow. Discontinuities in the value of this counter can occur at reinitialization of the managed system, and at other times as indicated by the value of ifCounterDiscontinuityTime of the associated MAC Domain interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmtsDsidTable		1.3.6.1.4.1.4491.2.1.21.1.18
This object describes DSID information stored in the CMTS. The CMTS reports the current status of existing DSIDs. When a DSID is created during the registration process or a DBC transaction, a corresponding object instance is created. If a DSID is deleted or changed via a DBC message the corresponding object instance is deleted or updated respectively.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3CmtsDsidEntry

docsQos3CmtsDsidEntry		1.3.6.1.4.1.4491.2.1.21.1.18.1
The conceptual row of docsQos3CmtsDsidTable. The ifIndex key corresponds to the MAC Domain interface of the DSID.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3CmtsDsidEntry

docsQos3CmtsDsidDsid		1.3.6.1.4.1.4491.2.1.21.1.18.1.1
This key represents the DSID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsid

docsQos3CmtsDsidUsage		1.3.6.1.4.1.4491.2.1.21.1.18.1.2
This attribute indicates the properties of the DSID. The bits are defined as follows: 'resequencing' This bit is set to 1 for a Resequencing DSID. 'multicastCapable' This bit is set to 1 for a DSID that is capable of transporting multicast traffic (i.e., the DSID has multicast forwarding attributes). 'multicastReplication' This bit is set to 1 for a DSID that is used for transporting a multicast replication (i.e. there is a corresponding instance of the MulticastRepl object). 'bonding' This bit is set to a 1 for a DSID that is associated with a bonding group.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	resequencing(0), multicastCapable(1), multicastReplication(2), bonding(3)

docsQos3CmtsDsidDsChSet		1.3.6.1.4.1.4491.2.1.21.1.18.1.3
This attribute represents the Downstream Channel Set over which the DSID is being resequenced.
Status: current	Access: read-only
OBJECT-TYPE
	ChSetId

docsQos3CmtsDsidReseqWaitTime		1.3.6.1.4.1.4491.2.1.21.1.18.1.4
This attribute represents the DSID Resequencing Wait Time that is used for this DSID. This attribute is only valid when the Usage attribute has the resequencing bit set to 1. This attribute returns a value of 0 when the Usage attribute has the resequencing bit set to 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..180

docsQos3CmtsDsidReseqWarnThrshld		1.3.6.1.4.1.4491.2.1.21.1.18.1.5
This attribute represents the DSID Resequencing Warning Threshold that is used for this DSID. The value of 0 indicates that the threshold warnings are disabled. This attribute is only valid when the Usage attribute has the resequencing bit set to 1. This attribute returns a value of 0 when the Usage attribute has the resequencing bit set to 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..179

docsQos3CmtsDsidStatusHldoffTimerSeqOutOfRng		1.3.6.1.4.1.4491.2.1.21.1.18.1.6
This attribute represents the hold-off timer for reporting Out-of-Range Events via the CM-STATUS MAC Management message. This attribute is only valid when the Usage attribute has the resequencing bit set to 1. This attribute returns a value of 0 when the Usage attribute has the resequencing bit set to 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3CmtsDsidCurrentSeqNum		1.3.6.1.4.1.4491.2.1.21.1.18.1.7
This attribute reports the value of the most recent sequence number assigned by the CMTS for this DSID. This attribute is only valid when the Usage attribute has the resequencing bit set to 1. This attribute returns a value of 0 when the Usage attribute has the resequencing bit set to 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3CmtsDebugDsidTable		1.3.6.1.4.1.4491.2.1.21.1.19
The CMTS Debug DSID object contains the control of DSID debug statistics reporting An instance in this object defines the DSID and MAC domain to which the CmtsDebugDsidStats collects statistics for the downstream channel associated with that DSID and MAC Domain. The deletion of an instance stops the reporting of statistics for the specified DSID. This object supports instance creation and deletion. The CMTS MUST support at least one instance of this object.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3CmtsDebugDsidEntry

docsQos3CmtsDebugDsidEntry		1.3.6.1.4.1.4491.2.1.21.1.19.1
The conceptual row of docsQos3CmtsDebugDsidTable. The ifIndex key corresponds to the MAC Domain interface of the DSID.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3CmtsDebugDsidEntry

docsQos3CmtsDebugDsidDsid		1.3.6.1.4.1.4491.2.1.21.1.19.1.1
This attribute represents the DSID value to be debugged, identified by the IfIndex attribute of this object.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsid

docsQos3CmtsDebugDsidRowStatus		1.3.6.1.4.1.4491.2.1.21.1.19.1.2
The conceptual row status of this object.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

docsQos3CmtsDebugDsidStatsTable		1.3.6.1.4.1.4491.2.1.21.1.20
The CMTS Debug DSID Stats object describes statistics at the CMTS for the forwarding of DSID-labeled downstream packets. The CMTS creates an instance for every combination of MAC Domain, DSID value, and downstream channel on which packets labeled with that DSID are transmitted. The CMTS does not delete such instances while the corresponding CmtsDebug object control instance exists.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3CmtsDebugDsidStatsEntry

docsQos3CmtsDebugDsidStatsEntry		1.3.6.1.4.1.4491.2.1.21.1.20.1
The conceptual row of docsQos3CmtsDebugDsidStatsTable. The ifIndex key corresponds to the MAC Domain interface of the DSID.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3CmtsDebugDsidStatsEntry

docsQos3CmtsDebugDsidStatsDsIfIndex		1.3.6.1.4.1.4491.2.1.21.1.20.1.1
This key represents an interface index of a downstream channel that belongs to the DSID
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIndex

docsQos3CmtsDebugDsidStatsDsidPackets		1.3.6.1.4.1.4491.2.1.21.1.20.1.2
This attribute is a counter which contains the number of packets transmitted by the CMTS which are labeled with the DSID on the downstream channel. Discontinuities in the value of this counter can occur as indicated by the value of ifCounterDiscontinuityTime of the associated Downstream interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

docsQos3CmtsDebugDsidStatsDsidOctets		1.3.6.1.4.1.4491.2.1.21.1.20.1.3
This attribute counts the number of bytes transmitted by the CMTS which are labeled with the DSID on the downstream interface. Discontinuities in the value of this counter can occur as indicated by the value of ifCounterDiscontinuityTime of the associated Downstream interface index.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

docsQos3CmDsidTable		1.3.6.1.4.1.4491.2.1.21.1.21
When a DSID is created, during the registration process or a DBC transaction,. The CM reports the current status of existing DSID, for example, if a DSID is deleted or changed via DBC messages the corresponding object instance is deleted or updated respectively.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3CmDsidEntry

docsQos3CmDsidEntry		1.3.6.1.4.1.4491.2.1.21.1.21.1
The conceptual row of docsQos3CmDsidTable The ifIndex key corresponds to the MAC Domain interface of the DSID.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3CmDsidEntry

docsQos3CmDsidDsid		1.3.6.1.4.1.4491.2.1.21.1.21.1.1
This key represents the DSID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsid

docsQos3CmDsidUsage		1.3.6.1.4.1.4491.2.1.21.1.21.1.2
This attribute indicates the properties of the DSID. The bits are defined as follows: 'resequencing' : This bit is set to 1 for a Resequencing DSID. 'multicastCapable' : This bit is set to 1 for a DSID that is capable of transporting multicast traffic (e.g., the DSID has multicast forwarding attributes).
Status: current	Access: read-only
OBJECT-TYPE
	BITS	resequencing(0), multicastCapable(1)

docsQos3CmDsidNumReseqChs		1.3.6.1.4.1.4491.2.1.21.1.21.1.3
This attribute represents the number of channels in the downstream resequencing channel list for this DSID.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..65535

docsQos3CmDsidReseqChList		1.3.6.1.4.1.4491.2.1.21.1.21.1.4
This attribute represents the Downstream Channel Set over which the DSID is being resequenced.
Status: current	Access: read-only
OBJECT-TYPE
	ChannelList

docsQos3CmDsidReseqWaitTime		1.3.6.1.4.1.4491.2.1.21.1.21.1.5
This attribute represents the DSID Resequencing Wait Time that is used for this DSID. This attribute is only valid when the Usage attribute has the resequencing bit set to 1. This attribute returns a value of 0 when the Usage attribute has the resequencing bit set to 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..180

docsQos3CmDsidReseqWarnThrshld		1.3.6.1.4.1.4491.2.1.21.1.21.1.6
This attribute represents the DSID Resequencing Warning Threshold that is used for this DSID. The value of 0 indicates that the threshold warnings are disabled. This attribute is only valid when the Usage attribute has the resequencing bit set to 1. This attribute returns a value of 0 when the Usage attribute has the resequencing bit set to 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..179

docsQos3CmDsidStatusHldoffTimerSeqOutOfRng		1.3.6.1.4.1.4491.2.1.21.1.21.1.7
This attribute represents the hold-off timer for reporting Out-of-Range Events via the CM-STATUS MAC Management message. This attribute is only valid when the Usage attribute has the resequencing bit set to 1. This attribute returns a value of 0 when the Usage attribute has the resequencing bit set to 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3CmDsidOutOfRangeDiscards		1.3.6.1.4.1.4491.2.1.21.1.21.1.8
This attribute represents the current count of out-of-range packets discarded by the CM for a given resequencing context since an in-range packet was received. When this count exceeds 1000 and more than two minutes have elapsed since an in-range packet was received, the CM will reacquire sequence numbers for this resequencing context.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3CmDsidNextExpectedSeqNum		1.3.6.1.4.1.4491.2.1.21.1.21.1.9
This attribute represents the Next Expected Packet Sequence Number for a given resequencing context. This attribute is only valid when the Usage attribute has the resequencing bit set to 1. This attribute returns a value of 0 when the Usage attribute has the resequencing bit set to 0.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..65535

docsQos3CmDsidCmInterfaceMask		1.3.6.1.4.1.4491.2.1.21.1.21.1.10
This attribute represents the bitmap of the interfaces communicated to the CM in a Multicast DSID encoding.
Status: current	Access: read-only
OBJECT-TYPE
	DocsL2vpnIfList

docsQos3CmDsidFwdCmInterfaceMask		1.3.6.1.4.1.4491.2.1.21.1.21.1.11
This attribute represents the bitmap of the interfaces to which the CM forwards multicast traffic: a logical OR of interfaces identified in CmInterfaceMask and interfaces associated with the client MAC addresses identified in the docsDevCmDsidMac instances for this DSID.
Status: current	Access: read-only
OBJECT-TYPE
	DocsL2vpnIfList

docsQos3CmDsidStatsTable		1.3.6.1.4.1.4491.2.1.21.1.22
This object defines a set of statistics the CM collects per Dsid.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3CmDsidStatsEntry

docsQos3CmDsidStatsEntry		1.3.6.1.4.1.4491.2.1.21.1.22.1
The conceptual row of docsQos3CmDsidStatsTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3CmDsidStatsEntry

docsQos3CmDsidStatsDsid		1.3.6.1.4.1.4491.2.1.21.1.22.1.1
This key represents the interface index of the MAC Domain associated with the DSID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsid

docsQos3CmDsidStatsSeqNumMissing		1.3.6.1.4.1.4491.2.1.21.1.22.1.2
This attribute counts the number of times the Next Expected Packet Sequence Number is declared lost. In this case one or more data packets are lost. This is generally caused by downstream packet loss.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmDsidStatsSkewThreshExceeds		1.3.6.1.4.1.4491.2.1.21.1.22.1.3
This attribute counts in-range sequenced packets which were successfully received by the CM after a wait time longer than the Resequencing Warning Threshold.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmDsidStatsOutOfRangePackets		1.3.6.1.4.1.4491.2.1.21.1.22.1.4
This attribute counts the number of packets Counter received in a DSID reassembly context where the sequence number which is out of range.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

docsQos3CmDsidStatsNumPackets		1.3.6.1.4.1.4491.2.1.21.1.22.1.5
This attribute counts the total number of data packets of a DSID context forwarded for further processing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter64

docsQos3CmDsidClientTable		1.3.6.1.4.1.4491.2.1.21.1.23
This object contains the client MAC addresses that the CMTS requests that the CM uses to replicate Multicast DSIDs during registration or during a DBC transaction. When a DSID is created that includes client MAC addresses, or when client MAC addresses are added to a DSID, new rows are created to indicate the added client MAC addresses. When a Client MAC address is deleted from a DSID, the corresponding row is deleted. When a DSID is deleted, all corresponding rows are deleted, too.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DocsQos3CmDsidClientEntry

docsQos3CmDsidClientEntry		1.3.6.1.4.1.4491.2.1.21.1.23.1
The conceptual row of docsQos3CmDsidClientTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	DocsQos3CmDsidClientEntry

docsQos3CmDsidClientDsid		1.3.6.1.4.1.4491.2.1.21.1.23.1.1
This key defines the DSID that the client MAC addresses are associated with.
Status: current	Access: not-accessible
OBJECT-TYPE
	Dsid

docsQos3CmDsidClientClientMacId		1.3.6.1.4.1.4491.2.1.21.1.23.1.2
This key defines a uniquely identified Client Mac Addresses associated with the DSID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..65535

docsQos3CmDsidClientClientMacAddr		1.3.6.1.4.1.4491.2.1.21.1.23.1.3
This attribute defines a client MAC address to which Multicast traffic labeled with this DSID should be forwarded.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

docsQos3MibConformance		1.3.6.1.4.1.4491.2.1.21.2
OBJECT IDENTIFIER

docsQos3MibCompliances		1.3.6.1.4.1.4491.2.1.21.2.1
OBJECT IDENTIFIER

docsQos3MibGroups		1.3.6.1.4.1.4491.2.1.21.2.2
OBJECT IDENTIFIER

docsQos3Compliance		1.3.6.1.4.1.4491.2.1.21.2.1.1
The compliance statement of managed objects common for Cable Modem Termination Sytems (CMTS) and Cable Modems (CM).
Status: current	Access: read-only
MODULE-COMPLIANCE

docsQos3BaseGroup		1.3.6.1.4.1.4491.2.1.21.2.2.1
Group of objects implemented in both CM and CMTS.
Status: current	Access: read-only
OBJECT-GROUP

docsQos3CmtsGroup		1.3.6.1.4.1.4491.2.1.21.2.2.2
Group of objects implemented in the CMTS only.
Status: current	Access: read-only
OBJECT-GROUP

docsQos3CmGroup		1.3.6.1.4.1.4491.2.1.21.2.2.3
Group of objects implemented in the CM only.
Status: current	Access: read-only
OBJECT-GROUP