DKSF-50-11-X-X-X

File: DKSF-50-11-X-X-X.mib (20040 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-MIB

Imported symbols

enterprises MODULE-IDENTITY OBJECT-TYPE
Counter32 Gauge32 Counter64
Integer32 TimeTicks NOTIFICATION-TYPE
TEXTUAL-CONVENTION DisplayString TruthValue
TimeStamp snmpTraps

Defined Types

NpPwrEntry  
SEQUENCE    
  npPwrChannelN INTEGER
  npPwrStartReset INTEGER
  npPwrManualMode INTEGER
  npPwrResetsCounter INTEGER
  npPwrRepeatingResetsCounter INTEGER
  npPwrMemo DisplayString

NpThermoEntry  
SEQUENCE    
  npThermoSensorN INTEGER
  npThermoValue INTEGER
  npThermoStatus INTEGER
  npThermoLow INTEGER
  npThermoHigh INTEGER
  npThermoMemo DisplayString

NpIoEntry  
SEQUENCE    
  npIoLineN INTEGER
  npIoLevelIn INTEGER
  npIoLevelOut INTEGER
  npIoMemo DisplayString
  npIoPulseCounter Counter32
  npIoSinglePulseDuration INTEGER
  npIoSinglePulseStart INTEGER

NpCurLoopEntry  
SEQUENCE    
  npCurLoopN INTEGER
  npCurLoopStatus INTEGER
  npCurLoopI INTEGER
  npCurLoopV INTEGER
  npCurLoopR INTEGER
  npCurLoopPower INTEGER

Defined Values

netPing 1.3.6.1.4.1.25728.50
Generic MIB for NetPing remote sensing and control
MODULE-IDENTITY    

lightcom 1.3.6.1.4.1.25728
OBJECT IDENTIFIER    

npTrapInfo 1.3.6.1.4.1.25728.90
OBJECT IDENTIFIER    

npTrapEmailTo 1.3.6.1.4.1.25728.90.1
user-specified e-mail for NetPing Trap Forwarding Service
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npPwr 1.3.6.1.4.1.25728.5800
OBJECT IDENTIFIER    

npPwrTable 1.3.6.1.4.1.25728.5800.3
Watchdog and outlet/relay control table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NpPwrEntry

npPwrEntry 1.3.6.1.4.1.25728.5800.3.1
Watchdog and outlet/relay control table row
Status: current Access: not-accessible
OBJECT-TYPE    
  NpPwrEntry  

npPwrChannelN 1.3.6.1.4.1.25728.5800.3.1.1
The id of watchdog/power channel
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

npPwrStartReset 1.3.6.1.4.1.25728.5800.3.1.2
Write 1 to start reset On read: 0 - normal operation 1 - reset is active 2 - reboot pause is active
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2  

npPwrManualMode 1.3.6.1.4.1.25728.5800.3.1.3
Mode of power channel 0 - manual off 1 - manual on 2 - watchdog
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1), watchdog(2)  

npPwrResetsCounter 1.3.6.1.4.1.25728.5800.3.1.4
Counter of watchdog resets Write 0 to clear.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

npPwrRepeatingResetsCounter 1.3.6.1.4.1.25728.5800.3.1.5
Counter of continous failed watchdog resets
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

npPwrMemo 1.3.6.1.4.1.25728.5800.3.1.6
Watchdog/power channel memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npThermo 1.3.6.1.4.1.25728.8800
OBJECT IDENTIFIER    

npThermoTable 1.3.6.1.4.1.25728.8800.1
Thermo Sensors Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NpThermoEntry

npThermoEntry 1.3.6.1.4.1.25728.8800.1.1
Thermo Sensors Table Row
Status: current Access: not-accessible
OBJECT-TYPE    
  NpThermoEntry  

npThermoSensorN 1.3.6.1.4.1.25728.8800.1.1.1
The id of temperature sensor, 1 to 8
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

npThermoValue 1.3.6.1.4.1.25728.8800.1.1.2
Temperature, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoStatus 1.3.6.1.4.1.25728.8800.1.1.3
Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER failed(0), low(1), norm(2), high(3)  

npThermoLow 1.3.6.1.4.1.25728.8800.1.1.4
Bottom margin of normal temperature range, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoHigh 1.3.6.1.4.1.25728.8800.1.1.5
Top margin of normal temperature range, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoMemo 1.3.6.1.4.1.25728.8800.1.1.6
T channel memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npThermoTraps 1.3.6.1.4.1.25728.8800.2
OBJECT IDENTIFIER    

npThermoTrapPrefix 1.3.6.1.4.1.25728.8800.2.0
OBJECT IDENTIFIER    

npThermoTrapSensorN 1.3.6.1.4.1.25728.8800.2.1
The id of temperature sensor, 1 to 8
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

npThermoTrapValue 1.3.6.1.4.1.25728.8800.2.2
Temperature, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoTrapStatus 1.3.6.1.4.1.25728.8800.2.3
Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER failed(0), low(1), norm(2), high(3)  

npThermoTrapLow 1.3.6.1.4.1.25728.8800.2.4
Bottom margin of normal temperature range, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoTrapHigh 1.3.6.1.4.1.25728.8800.2.5
Top margin of normal temperature range, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..280  

npThermoTrapMemo 1.3.6.1.4.1.25728.8800.2.6
T channel memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npThermoTrap 1.3.6.1.4.1.25728.8800.2.0.1
Status of Thermo sensor is changed (crossing of normal temp. range)
Status: current Access: read-only
NOTIFICATION-TYPE    

npIo 1.3.6.1.4.1.25728.8900
OBJECT IDENTIFIER    

npIoTable 1.3.6.1.4.1.25728.8900.1
Digital Input/output Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NpIoEntry

npIoEntry 1.3.6.1.4.1.25728.8900.1.1
Digital Input/output Table Row
Status: current Access: not-accessible
OBJECT-TYPE    
  NpIoEntry  

npIoLineN 1.3.6.1.4.1.25728.8900.1.1.1
Number of IO line, from 1 to max supported
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

npIoLevelIn 1.3.6.1.4.1.25728.8900.1.1.2
Input level, 0 or 1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

npIoLevelOut 1.3.6.1.4.1.25728.8900.1.1.3
Output level, 0 or 1
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

npIoMemo 1.3.6.1.4.1.25728.8900.1.1.6
IO line memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npIoPulseCounter 1.3.6.1.4.1.25728.8900.1.1.9
Pulse Counter on IO input line (counts positive fronts) Write 0 to reset.
Status: current Access: read-write
OBJECT-TYPE    
  Counter32  

npIoSinglePulseDuration 1.3.6.1.4.1.25728.8900.1.1.12
Set duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100ms
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 100..25500  

npIoSinglePulseStart 1.3.6.1.4.1.25728.8900.1.1.13
Write 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDuration
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

npIoTraps 1.3.6.1.4.1.25728.8900.2
OBJECT IDENTIFIER    

npIoTrapPrefix 1.3.6.1.4.1.25728.8900.2.0
OBJECT IDENTIFIER    

npIoTrapLineN 1.3.6.1.4.1.25728.8900.2.1
Trap data, Number of IO line
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

npIoTrapLevelIn 1.3.6.1.4.1.25728.8900.2.2
Trap data, new Input level, 0 or 1
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

npIoTrapMemo 1.3.6.1.4.1.25728.8900.2.6
Trap data, IO line memo
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

npIoTrap 1.3.6.1.4.1.25728.8900.2.0.1
Input state of IO line is changed
Status: current Access: read-only
NOTIFICATION-TYPE    

npCurLoop 1.3.6.1.4.1.25728.8300
OBJECT IDENTIFIER    

npCurLoopTable 1.3.6.1.4.1.25728.8300.1
Current loop sensors Table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NpCurLoopEntry

npCurLoopEntry 1.3.6.1.4.1.25728.8300.1.1
Current loop sensors Table Row
Status: current Access: not-accessible
OBJECT-TYPE    
  NpCurLoopEntry  

npCurLoopN 1.3.6.1.4.1.25728.8300.1.1.1
Index of current loop, 1 to max supported
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

npCurLoopStatus 1.3.6.1.4.1.25728.8300.1.1.2
Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), alert(1), cut(2), short(3), notPowered(4)  

npCurLoopI 1.3.6.1.4.1.25728.8300.1.1.3
Loop current, mA
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopV 1.3.6.1.4.1.25728.8300.1.1.4
Voltage drop on the loop, mV
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopR 1.3.6.1.4.1.25728.8300.1.1.5
Resistance of the loop, Ohm
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopPower 1.3.6.1.4.1.25728.8300.1.1.7
Control of loop power 0=Off, 1=On, 2=reset by off/on power
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1), cyclePower(2)  

npCurLoopTraps 1.3.6.1.4.1.25728.8300.2
OBJECT IDENTIFIER    

npCurLoopTrapPrefix 1.3.6.1.4.1.25728.8300.2.0
OBJECT IDENTIFIER    

npCurLoopTrapN 1.3.6.1.4.1.25728.8300.2.1
Index of current loop, which status has changed
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

npCurLoopTrapStatus 1.3.6.1.4.1.25728.8300.2.2
Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), alert(1), cut(2), short(3), notPowered(4)  

npCurLoopTrapI 1.3.6.1.4.1.25728.8300.2.3
Loop current, mA
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopTrapV 1.3.6.1.4.1.25728.8300.2.4
Voltage drop on the loop, mV
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopTrapR 1.3.6.1.4.1.25728.8300.2.5
Resistance of the loop, Ohm
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..99999  

npCurLoopTrapPower 1.3.6.1.4.1.25728.8300.2.7
Status of loop power 0=Off, 1=On
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

npCurLoopTrap 1.3.6.1.4.1.25728.8300.2.0.1
Status of current loop N has changed!
Status: current Access: read-write
NOTIFICATION-TYPE    

npRelHumidity 1.3.6.1.4.1.25728.8400
OBJECT IDENTIFIER    

npRelHumSensor 1.3.6.1.4.1.25728.8400.2
OBJECT IDENTIFIER    

npRelHumSensorStatus 1.3.6.1.4.1.25728.8400.2.3
Status of the Rel.Humidity Sensor One 0=Normal, 1=Error or Sensor isn't connected
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), error(1)  

npRelHumSensorValueH 1.3.6.1.4.1.25728.8400.2.2
Relative humidity value, %
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

npRelHumSensorValueT 1.3.6.1.4.1.25728.8400.2.4
Sensor temperature, deg.C
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -60..200  

npRelHumSensorStatusH 1.3.6.1.4.1.25728.8400.2.5
Status of Relative Humiduty
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sensorFailed(0), belowSafeRange(1), inNormRange(2), aboveSafeRange(3)  

npRelHumSafeRangeHigh 1.3.6.1.4.1.25728.8400.2.7
Relative Humidity safe range, top margin, %RH
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

npRelHumSafeRangeLow 1.3.6.1.4.1.25728.8400.2.8
Relative Humidity safe range, bottom margin, %RH
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

npRelHumTraps 1.3.6.1.4.1.25728.8400.9
OBJECT IDENTIFIER    

npRelHumTrapPrefix 1.3.6.1.4.1.25728.8400.9.0
OBJECT IDENTIFIER    

npRelHumTrap 1.3.6.1.4.1.25728.8400.9.0.1
Status of Relative Humidity RH sensor has changed!
Status: current Access: read-only
NOTIFICATION-TYPE    

npIr 1.3.6.1.4.1.25728.7900
OBJECT IDENTIFIER    

npIrCtrl 1.3.6.1.4.1.25728.7900.1
OBJECT IDENTIFIER    

npIrPlayCmd 1.3.6.1.4.1.25728.7900.1.1
Write IR command number to send IR command
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16  

npIrReset 1.3.6.1.4.1.25728.7900.1.2
Write 1 to reset IR transiever. After reset, send IR command and check npIrStatus.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

npIrStatus 1.3.6.1.4.1.25728.7900.1.3
IR transiever status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), busyCaptureWaitingButton(1), busyCaptureWaitingIr(2), busyPlayback(3), error(255)  

npReboot 1.3.6.1.4.1.25728.911
OBJECT IDENTIFIER    

npSoftReboot 1.3.6.1.4.1.25728.911.1
Write 1 to reboot device after current operations completition
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

npResetStack 1.3.6.1.4.1.25728.911.2
Write 1 to re-initialize network stack
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

npForcedReboot 1.3.6.1.4.1.25728.911.3
Write 1 to immediate forced reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER