Cxr-connect-MIB

File: Cxr-connect-MIB.mib (99681 bytes)

Imported modules

RFC1155-SMI RFC-1215

Imported symbols

mgmt OBJECT-TYPE NetworkAddress
IpAddress Counter Gauge
TimeTicks enterprises TRAP-TYPE

Defined Types

PhysAddr  
OCTET STRING    

DisplayString  
OCTET STRING    

IfEntry  
SEQUENCE    
  ifIndex INTEGER
  ifDescr DisplayString
  ifType INTEGER
  ifMtu INTEGER
  ifSpeed Gauge
  ifPhysAddress OCTET STRING
  ifAdminStatus INTEGER
  ifOperStatus INTEGER
  ifLastChange TimeTicks
  ifInOctets Counter
  ifInUcastPkts Counter
  ifInNUcastPkts Counter
  ifInDiscards Counter
  ifInErrors Counter
  ifInUnknownProtos Counter
  ifOutOctets Counter
  ifOutUcastPkts Counter
  ifOutNUcastPkts Counter
  ifOutDiscards Counter
  ifOutErrors Counter
  ifOutQLen Gauge
  ifSpecific OBJECT IDENTIFIER

AtEntry  
SEQUENCE    
  atIfIndex INTEGER
  atPhysAddress OCTET STRING
  atNetAddress NetworkAddress

IpAddrEntry  
SEQUENCE    
  ipAdEntAddr IpAddress
  ipAdEntIfIndex INTEGER
  ipAdEntNetMask IpAddress
  ipAdEntBcastAddr INTEGER
  ipAdEntReasmMaxSize INTEGER 0..65535

IpRouteEntry  
SEQUENCE    
  ipRouteDest IpAddress
  ipRouteIfIndex INTEGER
  ipRouteMetric1 INTEGER
  ipRouteMetric2 INTEGER
  ipRouteMetric3 INTEGER
  ipRouteMetric4 INTEGER
  ipRouteNextHop IpAddress
  ipRouteType INTEGER
  ipRouteProto INTEGER
  ipRouteAge INTEGER
  ipRouteMask IpAddress
  ipRouteMetric5 INTEGER

IpNetToMediaEntry  
SEQUENCE    
  ipNetToMediaIfIndex INTEGER
  ipNetToMediaPhysAddress OCTET STRING
  ipNetToMediaNetAddress IpAddress
  ipNetToMediaType INTEGER

TcpConnEntry  
SEQUENCE    
  tcpConnState INTEGER
  tcpConnLocalAddress IpAddress
  tcpConnLocalPort INTEGER 0..65535
  tcpConnRemAddress IpAddress
  tcpConnRemPort INTEGER 0..65535

UdpEntry  
SEQUENCE    
  udpLocalAddress IpAddress
  udpLocalPort INTEGER 0..65535

SystemInfo  
SEQUENCE    
  sysDescr DisplayString
  sysObjectID OBJECT IDENTIFIER
  sysUpTime TimeTicks
  sysContact DisplayString
  sysName DisplayString
  sysLocation DisplayString
  sysServices DisplayString

IfEntryInfo  
SEQUENCE    
  ifIndex INTEGER
  ifDescr DisplayString
  ifType INTEGER
  ifMtu INTEGER
  ifSpeed Gauge
  ifPhysAddress OCTET STRING
  ifAdminStatus INTEGER
  ifOperStatus INTEGER
  ifLastChange TimeTicks
  ifSpecific OBJECT IDENTIFIER

IfPackStats  
SEQUENCE    
  ifIndex INTEGER
  ifInUcastPkts Counter
  ifInNUcastPkts Counter
  ifOutUcastPkts Counter
  ifOutNUcastPkts Counter
  ifInDiscards Counter
  ifInErrors Counter
  ifInUnknownProtos Counter
  ifOutDiscards Counter
  ifOutErrors Counter

IfByteStats  
SEQUENCE    
  ifIndex INTEGER
  ifInOctets Counter
  ifOutOctets Counter

IpGroup  
SEQUENCE    
  ipForwarding INTEGER
  ipDefaultTTL INTEGER
  ipInReceives Counter
  ipInHdrErrors Counter
  ipInAddrErrors Counter
  ipForwDatagrams Counter
  ipInUnknownProtos Counter
  ipInDiscards Counter
  ipInDelivers Counter
  ipOutRequests Counter
  ipOutDiscards Counter
  ipOutNoRoutes Counter
  ipReasmTimeout INTEGER
  ipReasmReqds Counter
  ipReasmOKs Counter
  ipReasmFails Counter
  ipFragOKs Counter
  ipFragFails Counter
  ipFragCreates Counter

IpStatsGroup  
SEQUENCE    
  ipInReceives Counter
  ipInDelivers Counter
  ipForwDatagrams Counter
  ipOutRequests Counter
  ipInHdrErrors Counter
  ipInAddrErrors Counter
  ipInUnknownProtos Counter
  ipInDiscards Counter
  ipOutDiscards Counter
  ipOutNoRoutes Counter
  ipReasmTimeout INTEGER
  ipReasmReqds Counter
  ipReasmOKs Counter
  ipReasmFails Counter
  ipFragOKs Counter
  ipFragFails Counter
  ipFragCreates Counter

IcmpGroup  
SEQUENCE    
  icmpInMsgs Counter
  icmpInErrors Counter
  icmpInDestUnreachs Counter
  icmpInTimeExcds Counter
  icmpInParmProbs Counter
  icmpInSrcQuenchs Counter
  icmpInRedirects Counter
  icmpInEchos Counter
  icmpInEchoReps Counter
  icmpInTimestamps Counter
  icmpInTimestampReps Counter
  icmpInAddrMasks Counter
  icmpInAddrMaskReps Counter
  icmpOutMsgs Counter
  icmpOutErrors Counter
  icmpOutDestUnreachs Counter
  icmpOutTimeExcds Counter
  icmpOutParmProbs Counter
  icmpOutSrcQuenchs Counter
  icmpOutRedirects Counter
  icmpOutEchos Counter
  icmpOutEchoReps Counter
  icmpOutTimestamps Counter
  icmpOutTimestampReps Counter
  icmpOutAddrMasks Counter
  icmpOutAddrMaskReps Counter

IcmpInfo  
SEQUENCE    
  icmpInMsgs Counter
  icmpInErrors Counter
  icmpInDestUnreachs Counter
  icmpInTimeExcds Counter
  icmpInParmProbs Counter
  icmpInSrcQuenchs Counter
  icmpInRedirects Counter
  icmpInEchos Counter
  icmpInEchoReps Counter
  icmpInTimestamps Counter
  icmpInTimestampReps Counter
  icmpInAddrMasks Counter
  icmpInAddrMaskReps Counter
  icmpOutMsgs Counter
  icmpOutErrors Counter
  icmpOutDestUnreachs Counter
  icmpOutTimeExcds Counter
  icmpOutParmProbs Counter
  icmpOutSrcQuenchs Counter
  icmpOutRedirects Counter
  icmpOutEchos Counter
  icmpOutEchoReps Counter
  icmpOutTimestamps Counter
  icmpOutTimestampReps Counter
  icmpOutAddrMasks Counter
  icmpOutAddrMaskReps Counter

IcmpInputStats  
SEQUENCE    
  icmpInMsgs Counter
  icmpInErrors Counter
  icmpInDestUnreachs Counter
  icmpInTimeExcds Counter
  icmpInParmProbs Counter
  icmpInSrcQuenchs Counter
  icmpInRedirects Counter
  icmpInEchos Counter
  icmpInEchoReps Counter
  icmpInTimestamps Counter
  icmpInTimestampReps Counter
  icmpInAddrMasks Counter
  icmpInAddrMaskReps Counter

IcmpOutputStats  
SEQUENCE    
  icmpOutMsgs Counter
  icmpOutErrors Counter
  icmpOutDestUnreachs Counter
  icmpOutTimeExcds Counter
  icmpOutParmProbs Counter
  icmpOutSrcQuenchs Counter
  icmpOutRedirects Counter
  icmpOutEchos Counter
  icmpOutEchoReps Counter
  icmpOutTimestamps Counter
  icmpOutTimestampReps Counter
  icmpOutAddrMasks Counter
  icmpOutAddrMaskReps Counter

TcpGroup  
SEQUENCE    
  tcpRtoAlgorithm INTEGER
  tcpRtoMin INTEGER
  tcpRtoMax INTEGER
  tcpMaxConn INTEGER
  tcpActiveOpens Counter
  tcpPassiveOpens Counter
  tcpAttemptFails Counter
  tcpEstabResets Counter
  tcpCurrEstab Gauge
  tcpInSegs Counter
  tcpOutSegs Counter
  tcpRetransSegs Counter

TcpStats  
SEQUENCE    
  tcpActiveOpens Counter
  tcpPassiveOpens Counter
  tcpAttemptFails Counter
  tcpEstabResets Counter
  tcpCurrEstab Gauge
  tcpInSegs Counter
  tcpOutSegs Counter
  tcpRetransSegs Counter
  tcpInErrs Counter
  tcpOutRsts Counter

UdpStats  
SEQUENCE    
  udpInDatagrams Counter
  udpNoPorts Counter
  udpInErrors Counter
  udpOutDatagrams Counter

SnmpInfo  
SEQUENCE    
  snmpEnableAuthenTraps INTEGER
  snmpInPkts Counter
  snmpOutPkts Counter
  snmpInBadVersions Counter
  snmpInBadCommunityNames Counter
  snmpInBadCommunityUses Counter
  snmpInASNParseErrs Counter
  snmpInTooBigs Counter
  snmpInNoSuchNames Counter
  snmpInBadValues Counter
  snmpInReadOnlys Counter
  snmpInGenErrs Counter
  snmpInTotalReqVars Counter
  snmpInTotalSetVars Counter
  snmpInGetRequests Counter
  snmpInGetNexts Counter
  snmpInSetRequests Counter
  snmpInGetResponses Counter
  snmpInTraps Counter
  snmpOutTooBigs Counter
  snmpOutNoSuchNames Counter
  snmpOutBadValues Counter
  snmpOutGenErrs Counter
  snmpOutGetRequests Counter
  snmpOutGetNexts Counter
  snmpOutSetRequests Counter
  snmpOutGetResponses Counter
  snmpOutTraps Counter

SnmpBasicGroup  
SEQUENCE    
  snmpEnableAuthenTraps INTEGER
  snmpInPkts Counter
  snmpOutPkts Counter
  snmpInTotalReqVars Counter
  snmpInTotalSetVars Counter
  snmpInGetRequests Counter
  snmpInGetNexts Counter
  snmpInSetRequests Counter
  snmpOutGetResponses Counter
  snmpOutTraps Counter

SnmpInputStats  
SEQUENCE    
  snmpInGetRequests Counter
  snmpInGetNexts Counter
  snmpInSetRequests Counter
  snmpInGetResponses Counter
  snmpInTraps Counter
  snmpInBadVersions Counter
  snmpInBadCommunityNames Counter
  snmpInBadCommunityUses Counter
  snmpInASNParseErrs Counter
  snmpInTooBigs Counter
  snmpInNoSuchNames Counter
  snmpInBadValues Counter
  snmpInReadOnlys Counter
  snmpInGenErrs Counter

SnmpOutputStats  
SEQUENCE    
  snmpOutGetRequests Counter
  snmpOutGetNexts Counter
  snmpOutSetRequests Counter
  snmpOutGetResponses Counter
  snmpOutTraps Counter
  snmpOutTooBigs Counter
  snmpOutNoSuchNames Counter
  snmpOutBadValues Counter
  snmpOutGenErrs Counter

Defined Values

mib-2 1.3.6.1.2.1
OBJECT IDENTIFIER    

cxr-connect 1.3.6.1.4.1.3810
OBJECT IDENTIFIER    

system 1.3.6.1.2.1.1
OBJECT IDENTIFIER    

interfaces 1.3.6.1.2.1.2
OBJECT IDENTIFIER    

at 1.3.6.1.2.1.3
OBJECT IDENTIFIER    

ip 1.3.6.1.2.1.4
OBJECT IDENTIFIER    

icmp 1.3.6.1.2.1.5
OBJECT IDENTIFIER    

tcp 1.3.6.1.2.1.6
OBJECT IDENTIFIER    

udp 1.3.6.1.2.1.7
OBJECT IDENTIFIER    

snmp 1.3.6.1.2.1.11
OBJECT IDENTIFIER    

cxr-connect-sys 1.3.6.1.4.1.3810.1
OBJECT IDENTIFIER    

cxr-connect-stat 1.3.6.1.4.1.3810.2
OBJECT IDENTIFIER    

cxr-connect-phys 1.3.6.1.4.1.3810.3
OBJECT IDENTIFIER    

cpuload 1.3.6.1.4.1.3810.1.1
OBJECT IDENTIFIER    

mem 1.3.6.1.4.1.3810.1.2
OBJECT IDENTIFIER    

mDRAM 1.3.6.1.4.1.3810.1.2.1
OBJECT IDENTIFIER    

mFLASH 1.3.6.1.4.1.3810.1.2.2
OBJECT IDENTIFIER    

mBUF 1.3.6.1.4.1.3810.1.2.3
OBJECT IDENTIFIER    

sysDescr 1.3.6.1.2.1.1.1
A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

sysObjectID 1.3.6.1.2.1.1.2
The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining `what kind of box' is being managed. For example, if vendor `Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

sysUpTime 1.3.6.1.2.1.1.3
The time (in hundredths of a second) since the network management portion of the system was last re-initialized.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

sysContact 1.3.6.1.2.1.1.4
The textual identification of the contact person for this managed node, together with information on how to contact this person (see ).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

sysName 1.3.6.1.2.1.1.5
An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name (see ).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

sysLocation 1.3.6.1.2.1.1.6
The physical location of this node (e.g., `telephone closet, 3rd floor') (see ).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

sysServices 1.3.6.1.2.1.1.7
A value which indicates the set of services that this entity primarily offers. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. For example, a node which performs primarily routing functions would have a value of 4 (2^(3-1)). In contrast, a node which is a host offering application services would have a value of 72 (2^(4-1) + 2^(7-1)). Note that in the context of the Internet suite of protocols, values should be calculated accordingly: layer functionality 1 physical (e.g., repeaters) 2 datalink/subnetwork (e.g., bridges) 3 internet (e.g., IP gateways) 4 end-to-end (e.g., IP hosts) 7 applications (e.g., mail relays) For systems including OSI protocols, layers 5 and 6 may also be counted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..127  

ifNumber 1.3.6.1.2.1.2.1
The number of network interfaces (regardless of their current state) present on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ifTable 1.3.6.1.2.1.2.2
A list of interface entries. The number of entries is given by the value of ifNumber.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    IfEntry

ifEntry 1.3.6.1.2.1.2.2.1
An interface entry containing objects at the subnetwork layer and below for a particular interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IfEntry  

ifIndex 1.3.6.1.2.1.2.2.1.1
A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ifDescr 1.3.6.1.2.1.2.2.1.2
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

ifType 1.3.6.1.2.1.2.2.1.3
The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), regular1822(2), hdh1822(3), ddn-x25(4), rfc877-x25(5), ethernet-csmacd(6), iso88023-csmacd(7), iso88024-tokenBus(8), iso88025-tokenRing(9), iso88026-man(10), starLan(11), proteon-10Mbit(12), proteon-80Mbit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), t1-carrier(18), cept(19), basicISDN(20), primaryISDN(21), propPointToPointSerial(22), ppp(23), softwareLoopback(24), eon(25), ethernet-3Mbit(26), nsip(27), slip(28), frameRelay(32)  

ifMtu 1.3.6.1.2.1.2.2.1.4
The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ifSpeed 1.3.6.1.2.1.2.2.1.5
An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ifPhysAddress 1.3.6.1.2.1.2.2.1.6
The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ifAdminStatus 1.3.6.1.2.1.2.2.1.7
The desired state of the interface. The testing(3) state indicates that no operational packets can be passed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

ifOperStatus 1.3.6.1.2.1.2.2.1.8
The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

ifLastChange 1.3.6.1.2.1.2.2.1.9
The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

ifInOctets 1.3.6.1.2.1.2.2.1.10
The total number of octets received on the interface, including framing characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifInUcastPkts 1.3.6.1.2.1.2.2.1.11
The number of subnetwork-unicast packets delivered to a higher-layer protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifInNUcastPkts 1.3.6.1.2.1.2.2.1.12
The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifInDiscards 1.3.6.1.2.1.2.2.1.13
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifInErrors 1.3.6.1.2.1.2.2.1.14
The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifInUnknownProtos 1.3.6.1.2.1.2.2.1.15
The number of packets received via the interface which were discarded because of an unknown or unsupported protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifOutOctets 1.3.6.1.2.1.2.2.1.16
The total number of octets transmitted out of the interface, including framing characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifOutUcastPkts 1.3.6.1.2.1.2.2.1.17
The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifOutNUcastPkts 1.3.6.1.2.1.2.2.1.18
The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifOutDiscards 1.3.6.1.2.1.2.2.1.19
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifOutErrors 1.3.6.1.2.1.2.2.1.20
The number of outbound packets that could not be transmitted because of errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ifOutQLen 1.3.6.1.2.1.2.2.1.21
The length of the output packet queue (in packets).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ifSpecific 1.3.6.1.2.1.2.2.1.22
A reference to MIB definitions specific to the particular media being used to realize the interface. For example, if the interface is realized by an ethernet, then the value of this object refers to a document defining objects specific to ethernet. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

atTable 1.3.6.1.2.1.3.1
The Address Translation tables contain the NetworkAddress to `physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries.
Status: deprecated Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    AtEntry

atEntry 1.3.6.1.2.1.3.1.1
Each entry contains one NetworkAddress to `physical' address equivalence.
Status: deprecated Access: read-only
OBJECT-TYPE    
  AtEntry  

atIfIndex 1.3.6.1.2.1.3.1.1.1
The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

atPhysAddress 1.3.6.1.2.1.3.1.1.2
The media-dependent `physical' address. Setting this object to a null string (one of zero length) has the effect of invaliding the corresponding entry in the atTable object. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant atPhysAddress object.
Status: deprecated Access: read-only
OBJECT-TYPE    
  OCTET STRING  

atNetAddress 1.3.6.1.2.1.3.1.1.3
The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address.
Status: deprecated Access: read-only
OBJECT-TYPE    
  NetworkAddress  

ipForwarding 1.3.6.1.2.1.4.1
The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER gateway(1), host(2)  

ipDefaultTTL 1.3.6.1.2.1.4.2
The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipInReceives 1.3.6.1.2.1.4.3
The total number of input datagrams received from interfaces, including those received in error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipInHdrErrors 1.3.6.1.2.1.4.4
The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipInAddrErrors 1.3.6.1.2.1.4.5
The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipForwDatagrams 1.3.6.1.2.1.4.6
The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipInUnknownProtos 1.3.6.1.2.1.4.7
The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipInDiscards 1.3.6.1.2.1.4.8
The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipInDelivers 1.3.6.1.2.1.4.9
The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipOutRequests 1.3.6.1.2.1.4.10
The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipOutDiscards 1.3.6.1.2.1.4.11
The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipOutNoRoutes 1.3.6.1.2.1.4.12
The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipReasmTimeout 1.3.6.1.2.1.4.13
The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipReasmReqds 1.3.6.1.2.1.4.14
The number of IP fragments received which needed to be reassembled at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipReasmOKs 1.3.6.1.2.1.4.15
The number of IP datagrams successfully re- assembled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipReasmFails 1.3.6.1.2.1.4.16
The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipFragOKs 1.3.6.1.2.1.4.17
The number of IP datagrams that have been successfully fragmented at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipFragFails 1.3.6.1.2.1.4.18
The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipFragCreates 1.3.6.1.2.1.4.19
The number of IP datagram fragments that have been generated as a result of fragmentation at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipAddrTable 1.3.6.1.2.1.4.20
The table of addressing information relevant to this entity's IP addresses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    IpAddrEntry

ipAddrEntry 1.3.6.1.2.1.4.20.1
The addressing information for one of this entity's IP addresses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddrEntry  

ipAdEntAddr 1.3.6.1.2.1.4.20.1.1
The IP address to which this entry's addressing information pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipAdEntIfIndex 1.3.6.1.2.1.4.20.1.2
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipAdEntNetMask 1.3.6.1.2.1.4.20.1.3
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipAdEntBcastAddr 1.3.6.1.2.1.4.20.1.4
The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipAdEntReasmMaxSize 1.3.6.1.2.1.4.20.1.5
The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

ipRouteTable 1.3.6.1.2.1.4.21
This entity's IP Routing table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    IpRouteEntry

ipRouteEntry 1.3.6.1.2.1.4.21.1
A route to a particular destination.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpRouteEntry  

ipRouteDest 1.3.6.1.2.1.4.21.1.1
The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipRouteIfIndex 1.3.6.1.2.1.4.21.1.2
The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipRouteMetric1 1.3.6.1.2.1.4.21.1.3
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipRouteMetric2 1.3.6.1.2.1.4.21.1.4
An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipRouteMetric3 1.3.6.1.2.1.4.21.1.5
An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipRouteMetric4 1.3.6.1.2.1.4.21.1.6
An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipRouteNextHop 1.3.6.1.2.1.4.21.1.7
The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipRouteType 1.3.6.1.2.1.4.21.1.8
The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), direct(3), remote(4)  

ipRouteProto 1.3.6.1.2.1.4.21.1.9
The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), local(2), netmgmt(3), icmp(4), egp(5), ggp(6), hello(7), rip(8), is-is(9), es-is(10), ciscoIgrp(11), bbnSpfIgp(12), ospf(13), bgp(14)  

ipRouteAge 1.3.6.1.2.1.4.21.1.10
The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipRouteMask 1.3.6.1.2.1.4.21.1.11
Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipRouteMetric5 1.3.6.1.2.1.4.21.1.12
An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipNetToMediaTable 1.3.6.1.2.1.4.22
The IP Address Translation table used for mapping from IP addresses to physical addresses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    IpNetToMediaEntry

ipNetToMediaEntry 1.3.6.1.2.1.4.22.1
Each entry contains one IpAddress to `physical' address equivalence.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpNetToMediaEntry  

ipNetToMediaIfIndex 1.3.6.1.2.1.4.22.1.1
The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipNetToMediaPhysAddress 1.3.6.1.2.1.4.22.1.2
The media-dependent `physical' address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ipNetToMediaNetAddress 1.3.6.1.2.1.4.22.1.3
The IpAddress corresponding to the media- dependent `physical' address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipNetToMediaType 1.3.6.1.2.1.4.22.1.4
The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipNetToMediaType object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), dynamic(3), static(4)  

icmpInMsgs 1.3.6.1.2.1.5.1
The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInErrors 1.3.6.1.2.1.5.2
The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInDestUnreachs 1.3.6.1.2.1.5.3
The number of ICMP Destination Unreachable messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInTimeExcds 1.3.6.1.2.1.5.4
The number of ICMP Time Exceeded messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInParmProbs 1.3.6.1.2.1.5.5
The number of ICMP Parameter Problem messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInSrcQuenchs 1.3.6.1.2.1.5.6
The number of ICMP Source Quench messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInRedirects 1.3.6.1.2.1.5.7
The number of ICMP Redirect messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInEchos 1.3.6.1.2.1.5.8
The number of ICMP Echo (request) messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInEchoReps 1.3.6.1.2.1.5.9
The number of ICMP Echo Reply messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInTimestamps 1.3.6.1.2.1.5.10
The number of ICMP Timestamp (request) messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInTimestampReps 1.3.6.1.2.1.5.11
The number of ICMP Timestamp Reply messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInAddrMasks 1.3.6.1.2.1.5.12
The number of ICMP Address Mask Request messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpInAddrMaskReps 1.3.6.1.2.1.5.13
The number of ICMP Address Mask Reply messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutMsgs 1.3.6.1.2.1.5.14
The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutErrors 1.3.6.1.2.1.5.15
The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutDestUnreachs 1.3.6.1.2.1.5.16
The number of ICMP Destination Unreachable messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutTimeExcds 1.3.6.1.2.1.5.17
The number of ICMP Time Exceeded messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutParmProbs 1.3.6.1.2.1.5.18
The number of ICMP Parameter Problem messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutSrcQuenchs 1.3.6.1.2.1.5.19
The number of ICMP Source Quench messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutRedirects 1.3.6.1.2.1.5.20
The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutEchos 1.3.6.1.2.1.5.21
The number of ICMP Echo (request) messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutEchoReps 1.3.6.1.2.1.5.22
The number of ICMP Echo Reply messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutTimestamps 1.3.6.1.2.1.5.23
The number of ICMP Timestamp (request) messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutTimestampReps 1.3.6.1.2.1.5.24
The number of ICMP Timestamp Reply messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutAddrMasks 1.3.6.1.2.1.5.25
The number of ICMP Address Mask Request messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

icmpOutAddrMaskReps 1.3.6.1.2.1.5.26
The number of ICMP Address Mask Reply messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpRtoAlgorithm 1.3.6.1.2.1.6.1
The algorithm used to determine the timeout value used for retransmitting unacknowledged octets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), constant(2), rsre(3), vanj(4)  

tcpRtoMin 1.3.6.1.2.1.6.2
The minimum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the LBOUND quantity described in RFC 793.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tcpRtoMax 1.3.6.1.2.1.6.3
The maximum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the UBOUND quantity described in RFC 793.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tcpMaxConn 1.3.6.1.2.1.6.4
The limit on the total number of TCP connections the entity can support. In entities where the maximum number of connections is dynamic, this object should contain the value -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tcpActiveOpens 1.3.6.1.2.1.6.5
The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpPassiveOpens 1.3.6.1.2.1.6.6
The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpAttemptFails 1.3.6.1.2.1.6.7
The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpEstabResets 1.3.6.1.2.1.6.8
The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpCurrEstab 1.3.6.1.2.1.6.9
The number of TCP connections for which the current state is either ESTABLISHED or CLOSE- WAIT.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

tcpInSegs 1.3.6.1.2.1.6.10
The total number of segments received, including those received in error. This count includes segments received on currently established connections.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpOutSegs 1.3.6.1.2.1.6.11
The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpRetransSegs 1.3.6.1.2.1.6.12
The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted octets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpConnTable 1.3.6.1.2.1.6.13
A table containing TCP connection-specific information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    TcpConnEntry

tcpConnEntry 1.3.6.1.2.1.6.13.1
Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TcpConnEntry  

tcpConnState 1.3.6.1.2.1.6.13.1.1
The state of this TCP connection. The only value which may be set by a management station is deleteTCB(12). Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(12), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection. As an implementation-specific option, a RST segment may be sent from the managed node to the other TCP endpoint (note however that RST segments are not sent reliably).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER closed(1), listen(2), synSent(3), synReceived(4), established(5), finWait1(6), finWait2(7), closeWait(8), lastAck(9), closing(10), timeWait(11), deleteTCB(12)  

tcpConnLocalAddress 1.3.6.1.2.1.6.13.1.2
The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

tcpConnLocalPort 1.3.6.1.2.1.6.13.1.3
The local port number for this TCP connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

tcpConnRemAddress 1.3.6.1.2.1.6.13.1.4
The remote IP address for this TCP connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

tcpConnRemPort 1.3.6.1.2.1.6.13.1.5
The remote port number for this TCP connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

tcpInErrs 1.3.6.1.2.1.6.14
The total number of segments received in error (e.g., bad TCP checksums).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpOutRsts 1.3.6.1.2.1.6.15
The number of TCP segments sent containing the RST flag.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

udpInDatagrams 1.3.6.1.2.1.7.1
The total number of UDP datagrams delivered to UDP users.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

udpNoPorts 1.3.6.1.2.1.7.2
The total number of received UDP datagrams for which there was no application at the destination port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

udpInErrors 1.3.6.1.2.1.7.3
The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

udpOutDatagrams 1.3.6.1.2.1.7.4
The total number of UDP datagrams sent from this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

udpTable 1.3.6.1.2.1.7.5
A table containing UDP listener information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    UdpEntry

udpEntry 1.3.6.1.2.1.7.5.1
Information about a particular current UDP listener.
Status: mandatory Access: read-only
OBJECT-TYPE    
  UdpEntry  

udpLocalAddress 1.3.6.1.2.1.7.5.1.1
The local IP address for this UDP listener. In the case of a UDP listener which is willing to accept datagrams for any IP interface associated with the node, the value 0.0.0.0 is used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

udpLocalPort 1.3.6.1.2.1.7.5.1.2
The local port number for this UDP listener.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

snmpInPkts 1.3.6.1.2.1.11.1
The total number of Messages delivered to the SNMP entity from the transport service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutPkts 1.3.6.1.2.1.11.2
The total number of SNMP Messages which were passed from the SNMP protocol entity to the transport service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInBadVersions 1.3.6.1.2.1.11.3
The total number of SNMP Messages which were delivered to the SNMP protocol entity and were for an unsupported SNMP version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInBadCommunityNames 1.3.6.1.2.1.11.4
The total number of SNMP Messages delivered to the SNMP protocol entity which used a SNMP community name not known to said entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInBadCommunityUses 1.3.6.1.2.1.11.5
The total number of SNMP Messages delivered to the SNMP protocol entity which represented an SNMP operation which was not allowed by the SNMP community named in the Message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInASNParseErrs 1.3.6.1.2.1.11.6
The total number of ASN.1 or BER errors encountered by the SNMP protocol entity when decoding received SNMP Messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInBadTypes 1.3.6.1.2.1.11.7
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInTooBigs 1.3.6.1.2.1.11.8
The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `tooBig'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInNoSuchNames 1.3.6.1.2.1.11.9
The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `noSuchName'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInBadValues 1.3.6.1.2.1.11.10
The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `badValue'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInReadOnlys 1.3.6.1.2.1.11.11
The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `readOnly'. It should be noted that it is a protocol error to generate an SNMP PDU which contains the value `readOnly' in the error-status field, as such this object is provided as a means of detecting incorrect implementations of the SNMP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInGenErrs 1.3.6.1.2.1.11.12
The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `genErr'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInTotalReqVars 1.3.6.1.2.1.11.13
The total number of MIB objects which have been retrieved successfully by the SNMP protocol entity as the result of receiving valid SNMP Get-Request and Get-Next PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInTotalSetVars 1.3.6.1.2.1.11.14
The total number of MIB objects which have been altered successfully by the SNMP protocol entity as the result of receiving valid SNMP Set-Request PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInGetRequests 1.3.6.1.2.1.11.15
The total number of SNMP Get-Request PDUs which have been accepted and processed by the SNMP protocol entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInGetNexts 1.3.6.1.2.1.11.16
The total number of SNMP Get-Next PDUs which have been accepted and processed by the SNMP protocol entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInSetRequests 1.3.6.1.2.1.11.17
The total number of SNMP Set-Request PDUs which have been accepted and processed by the SNMP protocol entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInGetResponses 1.3.6.1.2.1.11.18
The total number of SNMP Get-Response PDUs which have been accepted and processed by the SNMP protocol entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpInTraps 1.3.6.1.2.1.11.19
The total number of SNMP Trap PDUs which have been accepted and processed by the SNMP protocol entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutTooBigs 1.3.6.1.2.1.11.20
The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `tooBig.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutNoSuchNames 1.3.6.1.2.1.11.21
The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status is `noSuchName'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutBadValues 1.3.6.1.2.1.11.22
The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `badValue'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutReadOnlys 1.3.6.1.2.1.11.23
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutGenErrs 1.3.6.1.2.1.11.24
The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `genErr'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutGetRequests 1.3.6.1.2.1.11.25
The total number of SNMP Get-Request PDUs which have been generated by the SNMP protocol entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutGetNexts 1.3.6.1.2.1.11.26
The total number of SNMP Get-Next PDUs which have been generated by the SNMP protocol entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutSetRequests 1.3.6.1.2.1.11.27
The total number of SNMP Set-Request PDUs which have been generated by the SNMP protocol entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutGetResponses 1.3.6.1.2.1.11.28
The total number of SNMP Get-Response PDUs which have been generated by the SNMP protocol entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpOutTraps 1.3.6.1.2.1.11.29
The total number of SNMP Trap PDUs which have been generated by the SNMP protocol entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

snmpEnableAuthenTraps 1.3.6.1.2.1.11.30
Indicates whether the SNMP agent process is permitted to generate authentication-failure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authentication-failure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant between re-initializations of the network management system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

cpu1 1.3.6.1.4.1.3810.1.1.1
An estimate of the CPU current load based on the idle/busy state of processor. The measurement is done with a pre-calibrated loop, that means it's possible to have more than 100%.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

memDescr 1.3.6.1.4.1.3810.1.2.1.1
A textual string containing information about the type of memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

memMax 1.3.6.1.4.1.3810.1.2.1.2
Maximum amount of free memory of this type.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge  

memFree 1.3.6.1.4.1.3810.1.2.1.3
Amount of free memory of this type.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge  

memDescr 1.3.6.1.4.1.3810.1.2.2.1
A textual string containing information about the type of memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

memMax 1.3.6.1.4.1.3810.1.2.2.2
Maximum amount of free memory of this type.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge  

memFree 1.3.6.1.4.1.3810.1.2.2.3
Amount of free memory of this type.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge  

memDescr 1.3.6.1.4.1.3810.1.2.3.1
A textual string containing information about the type of memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

memMax 1.3.6.1.4.1.3810.1.2.3.2
Maximum amount of free memory of this type.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge  

memFree 1.3.6.1.4.1.3810.1.2.3.3
Amount of free memory of this type.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge  

comlog 1.3.6.1.4.1.3810.2.1
Communication log as displayed in numstat -j. Index 0 is the last log entry and maximum value of index depends of calls and log depth (see ).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

channelStatusTable 1.3.6.1.4.1.3810.3.1
A table containing all the possible shelves
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DisplayString

typesTable 1.3.6.1.4.1.3810.3.2
OBJECT IDENTIFIER    

type1 1.3.6.1.4.1.3810.3.2.1
OBJECT IDENTIFIER    

channelType1 1.3.6.1.4.1.3810.3.2.1.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber1 1.3.6.1.4.1.3810.3.2.1.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled1 1.3.6.1.4.1.3810.3.2.1.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type2 1.3.6.1.4.1.3810.3.2.2
OBJECT IDENTIFIER    

channelType2 1.3.6.1.4.1.3810.3.2.2.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber2 1.3.6.1.4.1.3810.3.2.2.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled2 1.3.6.1.4.1.3810.3.2.2.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type3 1.3.6.1.4.1.3810.3.2.3
OBJECT IDENTIFIER    

channelType3 1.3.6.1.4.1.3810.3.2.3.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber3 1.3.6.1.4.1.3810.3.2.3.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled3 1.3.6.1.4.1.3810.3.2.3.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type4 1.3.6.1.4.1.3810.3.2.4
OBJECT IDENTIFIER    

channelType4 1.3.6.1.4.1.3810.3.2.4.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber4 1.3.6.1.4.1.3810.3.2.4.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled4 1.3.6.1.4.1.3810.3.2.4.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type5 1.3.6.1.4.1.3810.3.2.5
OBJECT IDENTIFIER    

channelType5 1.3.6.1.4.1.3810.3.2.5.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber5 1.3.6.1.4.1.3810.3.2.5.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled5 1.3.6.1.4.1.3810.3.2.5.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type6 1.3.6.1.4.1.3810.3.2.6
OBJECT IDENTIFIER    

channelType6 1.3.6.1.4.1.3810.3.2.6.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber6 1.3.6.1.4.1.3810.3.2.6.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled6 1.3.6.1.4.1.3810.3.2.6.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type7 1.3.6.1.4.1.3810.3.2.7
OBJECT IDENTIFIER    

channelType7 1.3.6.1.4.1.3810.3.2.7.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber7 1.3.6.1.4.1.3810.3.2.7.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled7 1.3.6.1.4.1.3810.3.2.7.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type8 1.3.6.1.4.1.3810.3.2.8
OBJECT IDENTIFIER    

channelType8 1.3.6.1.4.1.3810.3.2.8.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber8 1.3.6.1.4.1.3810.3.2.8.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled8 1.3.6.1.4.1.3810.3.2.8.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type9 1.3.6.1.4.1.3810.3.2.9
OBJECT IDENTIFIER    

channelType9 1.3.6.1.4.1.3810.3.2.9.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber9 1.3.6.1.4.1.3810.3.2.9.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled9 1.3.6.1.4.1.3810.3.2.9.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type10 1.3.6.1.4.1.3810.3.2.10
OBJECT IDENTIFIER    

channelType10 1.3.6.1.4.1.3810.3.2.10.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber10 1.3.6.1.4.1.3810.3.2.10.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled10 1.3.6.1.4.1.3810.3.2.10.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type11 1.3.6.1.4.1.3810.3.2.11
OBJECT IDENTIFIER    

channelType11 1.3.6.1.4.1.3810.3.2.11.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber11 1.3.6.1.4.1.3810.3.2.11.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled11 1.3.6.1.4.1.3810.3.2.11.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type12 1.3.6.1.4.1.3810.3.2.12
OBJECT IDENTIFIER    

channelType12 1.3.6.1.4.1.3810.3.2.12.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber12 1.3.6.1.4.1.3810.3.2.12.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled12 1.3.6.1.4.1.3810.3.2.12.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type13 1.3.6.1.4.1.3810.3.2.13
OBJECT IDENTIFIER    

channelType13 1.3.6.1.4.1.3810.3.2.13.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber13 1.3.6.1.4.1.3810.3.2.13.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled13 1.3.6.1.4.1.3810.3.2.13.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

type14 1.3.6.1.4.1.3810.3.2.14
OBJECT IDENTIFIER    

channelType14 1.3.6.1.4.1.3810.3.2.14.1
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

channelMaxNumber14 1.3.6.1.4.1.3810.3.2.14.2
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

channelMaxInstalled14 1.3.6.1.4.1.3810.3.2.14.3
Reference Shelf Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

coldStart 0
A coldStart trap signifies that the sending protocol entity is reinitializing itself such that the agent's configuration or the rotocol entity implementation may be altered.
TRAP-TYPE    

linkDown 2
A linkDown trap signifies that the sending protocol entity recognizes a failure in one of the communication links represented in the agent's configuration.
TRAP-TYPE    

linkUp 3
A linkUp trap signifies that the sending protocol entity recognizes that one of the communication links represented in the agent's configuration has come up.
TRAP-TYPE    

authenticationFailure 4
An authenticationFailure trap signifies that the sending protocol entity is the addressee of a protocol message that is not properly authenticated. While implementations of the SNMP must be capable of generating this trap, they must also be capable of suppressing the emission of such traps via an implementation- specific mechanism.
TRAP-TYPE    

comStart 200
This trap is generated when communication request is sended to AT. Channel number is given in trap.
TRAP-TYPE    

comStop 201
This trap is generated when communication is ended. Channel number is given in trap.
TRAP-TYPE    

comRefused 202
This trap is generated when communication is not accepted because remote number is not registered. Channel number and ISDN number are given in trap.
TRAP-TYPE    

comIPDenied 203
This trap is generated when IP communication is denied because of filtration on IP address. IP address is given in trap.
TRAP-TYPE    

comSockDenied 204
This trap is generated when IP communication is denied because of filtration on IP socket address and number. IP addresses are given in trap.
TRAP-TYPE    

comIPXDenied 205
This trap is generated when IPX communication is denied because of filtration on IPX address. IPX address are given in trap.
TRAP-TYPE