Centrum-MIB

File: Centrum-MIB.mib (184821 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

enterprises IpAddress Counter
DisplayString OBJECT-TYPE TRAP-TYPE

Defined Types

PortEntry  
SEQUENCE    
  portIndex INTEGER
  portId INTEGER
  portSlot INTEGER
  portScriptIdx INTEGER
  portBaudrate INTEGER
  portParity INTEGER
  portStopBits INTEGER
  portDataBits INTEGER
  portCCSP INTEGER
  portPPPProbeInterval INTEGER
  portPPPMaxRcvPacketLength INTEGER
  portPPPAsyncCtrlChar INTEGER
  portPPPProtCompress INTEGER
  portPPPACCompress INTEGER
  portCRCErrors Counter
  portOversizes Counter
  portUndersizes Counter
  portCollisions Counter
  portInPackets Counter
  portOutPackets Counter
  portInBytes Counter
  portOutBytes Counter
  portResetPortCounters INTEGER
  portAsyncParityErrors Counter
  portAsyncCharFrameErrors Counter
  portAsyncOverrunErrors Counter
  portAsyncPktCksumErrors Counter
  portCTSState INTEGER
  portDCDState INTEGER
  portRIState INTEGER
  portSyncFcsErrors Counter
  portSyncMemoryErrors Counter
  portSyncOverrunErrors Counter
  portSyncUnderrunErrors Counter
  portIPCPState INTEGER
  portIPXCPState INTEGER
  portBNCPState INTEGER
  portDriverState INTEGER
  portSpeed INTEGER
  portTotalErrors Counter
  portTransmitDiscards Counter
  portReceiveCongestions Counter
  portUnknownProtocols Counter
  portAccessType INTEGER
  portDialHangUp INTEGER
  portPortDisabled INTEGER
  portArapCompress INTEGER
  portInterFace INTEGER
  portLEDLink INTEGER
  portLEDActivity INTEGER
  portLEDFault INTEGER
  portLinkType INTEGER
  portSwitchType INTEGER
  portSPID-1 DisplayString
  portSPID-2 DisplayString
  portDirectoryNo-1 DisplayString
  portDirectoryNo-2 DisplayString
  portLocalDialNo-1 DisplayString
  portLocalDialNo-2 DisplayString
  portLocalSubaddress-1 DisplayString
  portLocalSubaddress-2 DisplayString
  portProtocolMode INTEGER
  portPortReset INTEGER
  portIncomingCalls Counter
  portOutgoingCalls Counter
  portRemoteDialNo DisplayString
  portRemoteSubaddress DisplayString
  portISDNInterfaceType DisplayString
  portPathName DisplayString
  portILCCPState INTEGER
  portCurISDNBChannel INTEGER
  portLoginStatus INTEGER
  portLastConnectBChannel INTEGER
  portISDNPhyLineStatus INTEGER
  portTEIState INTEGER
  portLayer3Status INTEGER

PortSourceRouteEntry  
SEQUENCE    
  portSRMacAddress OCTET STRING Size(6)
  portSRState INTEGER
  portSRTimeToLive Counter
  portSRLargestFrame INTEGER
  portSRDirection INTEGER
  portSRRouteDescrpt DisplayString Size(0..70)

PrpaEntry  
SEQUENCE    
  prpaIndex INTEGER
  prpaName DisplayString Size(0..12)
  prpaType INTEGER
  prpaPortIdx INTEGER
  prpaAutoHangUp INTEGER
  prpaInPackets Counter
  prpaOutPackets Counter
  prpaInBytes Counter
  prpaOutBytes Counter
  prpaResetPrpaCounters INTEGER
  prpaLoginStatus INTEGER
  prpaLoginUserName DisplayString Size(0..10)
  prpaLoginTime DisplayString Size(0..8)
  prpaLoginDuration DisplayString Size(0..8)
  prpaLoginAttempts Counter
  prpaLoginInPackets Counter
  prpaLoginOutPackets Counter
  prpaLoginInBytes Counter
  prpaLoginOutBytes Counter
  prpaLoginParityErrors Counter
  prpaLoginFrameErrors Counter
  prpaLoginOverrunErrors Counter
  prpaLoginCksumErrors Counter
  prpaFilterAction INTEGER
  prpaFilterMap INTEGER
  prpaLoggerMap INTEGER
  prpaFilterCount Counter
  prpaLoggerCount Counter
  prpaDiscardedPackets Counter
  prpaForwardedPackets Counter
  prpaReceivedPackets Counter
  prpaSmartFiltering INTEGER
  prpaCurrentMacAddr OCTET STRING
  prpaIpEthernetII INTEGER
  prpaIpSnap INTEGER
  prpaRemotePcIpAddress IpAddress
  prpaIpxEn2WithNetBIOS INTEGER
  prpaIpx8023WithNetBIOS INTEGER
  prpaIpx8022WithNetBIOS INTEGER
  prpaIpxSnapWithNetBIOS INTEGER
  prpaXNS INTEGER
  prpaVinesEthernetII INTEGER
  prpaVinesSnap INTEGER
  prpaNetBIOS INTEGER
  prpaDECNet INTEGER
  prpaUnknowEthernetII INTEGER
  prpaUnknownSap INTEGER
  prpaUnknownSnap INTEGER
  prpaMulticastAddress OCTET STRING
  prpaXNSSap INTEGER
  prpaXNSSnap INTEGER
  prpaVinesSap INTEGER
  prpaIpxEn2 INTEGER
  prpaIpx8023 INTEGER
  prpaIpx8022 INTEGER
  prpaIpxSnap INTEGER
  prpaPortList DisplayString Size(0..48)
  prpaSpoofState INTEGER
  prpaCCPState INTEGER
  prpaIPCPState INTEGER
  prpaIPXCPState INTEGER
  prpaBNCPState INTEGER
  prpaARAPState INTEGER
  prpaLinkUtil INTEGER

PlocalEntry  
SEQUENCE    
  plocalIndex INTEGER
  plocalName DisplayString Size(0..12)
  plocalType INTEGER
  plocalPortIdx INTEGER
  plocalInPackets Counter
  plocalOutPackets Counter
  plocalInBytes Counter
  plocalOutBytes Counter
  plocalResetPlocalCounters INTEGER
  plocalFilterAction INTEGER
  plocalFilterMap INTEGER
  plocalLoggerMap INTEGER
  plocalFilterCount Counter
  plocalLoggerCount Counter
  plocalDiscardedPackets Counter
  plocalForwardedPackets Counter
  plocalReceivedPackets Counter

PrmtEntry  
SEQUENCE    
  prmtIndex INTEGER
  prmtName DisplayString Size(0..12)
  prmtType INTEGER
  prmtInitiator INTEGER
  prmtCongestThreshold INTEGER
  prmtScheduleType1 INTEGER
  prmtDaysScheduled1 INTEGER
  prmtStartTime1 OCTET STRING
  prmtHowLong1 OCTET STRING
  prmtScheduleType2 INTEGER
  prmtDaysScheduled2 INTEGER
  prmtStartTime2 OCTET STRING
  prmtHowLong2 OCTET STRING
  prmtInPackets Counter
  prmtOutPackets Counter
  prmtInBytes Counter
  prmtOutBytes Counter
  prmtResetPrmtCounters INTEGER
  prmtFilterAction INTEGER
  prmtFilterMap INTEGER
  prmtLoggerMap INTEGER
  prmtFilterCount Counter
  prmtLoggerCount Counter
  prmtDiscardedPackets Counter
  prmtForwardedPackets Counter
  prmtReceivedPackets Counter
  prmtSmartFiltering INTEGER
  prmtOutCongestions Counter
  prmtRmtRouterName DisplayString Size(0..32)
  prmtTypeSelection INTEGER
  prmtAsyncPortNo INTEGER
  prmtISDNPortNo INTEGER
  prmtISDNReqBaudRate INTEGER
  prmtSpoofState INTEGER
  prmtCCPState INTEGER
  prmtIPCPState INTEGER
  prmtIPXCPState INTEGER
  prmtBNCPState INTEGER
  prmtLinkUtil INTEGER
  prmtPMPortList DisplayString Size(0..48)
  prmtBUPortList DisplayString Size(0..48)
  prmtODPortList DisplayString Size(0..48)
  prmtSCPortList DisplayString Size(0..48)

PrmtPortEntry  
SEQUENCE    
  prmtPortPrmtIdx INTEGER
  prmtPortPortIdx INTEGER
  prmtPortType INTEGER
  prmtPortPhoneNumber OCTET STRING Size(0..15)
  prmtPortDirectoryNo OCTET STRING Size(0..20)

PrmtPhoneEntry  
SEQUENCE    
  prmtPhonePrmtIdx INTEGER
  prmtPhoneIdx INTEGER
  prmtPhoneType INTEGER
  prmtPhonePhoneNumber OCTET STRING Size(0..15)
  prmtPhoneDirectoryNo OCTET STRING Size(0..20)

IpRpaEntry  
SEQUENCE    
  ipRpaIndex INTEGER
  ipRpaCurrentClientIpAddress IpAddress
  ipRpaConfigClientIpAddress IpAddress
  ipRpaTcpHdrCompress INTEGER
  ipRpaType INTEGER

IpSRouteEntry  
SEQUENCE    
  ipSRouteIndex INTEGER
  ipSRouteName DisplayString Size(0..8)
  ipSRouteType INTEGER
  ipSRoutePathType INTEGER
  ipSRoutePathIdx INTEGER
  ipSRouteDestIpAddress IpAddress
  ipSRouteNextRouter IpAddress
  ipSRouteHopCount INTEGER

IpPLocalEntry  
SEQUENCE    
  ipPLocalIndex INTEGER
  ipPLocalIpAddress IpAddress
  ipPLocalNetMask IpAddress
  ipPLocalBcastAddr INTEGER

IpPRmtEntry  
SEQUENCE    
  ipPRmtIndex INTEGER
  ipPRmtIpAddress IpAddress
  ipPRmtNetMask IpAddress
  ipPRmtBcastAddr INTEGER
  ipPRmtRipUpdate INTEGER
  ipPRmtType INTEGER
  ipPRmtTcpHdrCompress INTEGER

IpxRpaEntry  
SEQUENCE    
  ipxRpaIndex INTEGER
  ipxRpaCurrHostAddr OCTET STRING Size(6)

IpxSRouteEntry  
SEQUENCE    
  ipxSRouteIndex INTEGER
  ipxSRouteName DisplayString Size(0..8)
  ipxSRouteType INTEGER
  ipxSRoutePathType INTEGER
  ipxSRoutePathIdx INTEGER
  ipxSRouteDestNetNumber OCTET STRING Size(4)
  ipxSRouteNextHostAddress OCTET STRING Size(6)
  ipxSRouteHopCount INTEGER

IpxPLocalEntry  
SEQUENCE    
  ipxPLocalIndex INTEGER
  ipxPLocalNetNumber OCTET STRING Size(4)
  ipxPLocalDataLinkType INTEGER

IpxPRmtEntry  
SEQUENCE    
  ipxPRmtIndex INTEGER
  ipxPRmtNetNumber OCTET STRING Size(4)
  ipxPRmtNripUpdate INTEGER
  ipxPRmtType INTEGER

IpxRtRipEntry  
SEQUENCE    
  ipxRtRipDestNetNumber OCTET STRING Size(4)
  ipxRtRipPathType INTEGER
  ipxRtRipPathIdx INTEGER
  ipxRtRipNextHostAddress OCTET STRING Size(6)
  ipxRtRipHopCount INTEGER
  ipxRtRipTicks INTEGER
  ipxRtRipRouteType INTEGER

IpxRtSapEntry  
SEQUENCE    
  ipxRtSapIndex INTEGER
  ipxRtSapServiceName OCTET STRING Size(48)
  ipxRtSapServiceType INTEGER
  ipxRtSapServerNetNumber OCTET STRING Size(4)
  ipxRtSapServerHostAddress OCTET STRING Size(6)

BrgFilterEntry  
SEQUENCE    
  brgFilterIndex INTEGER
  brgFilterName DisplayString Size(0..8)
  brgFilterType INTEGER
  brgFilterMask1Offset INTEGER
  brgFilterMask1Value INTEGER
  brgFilterMask1Type INTEGER
  brgFilterMask1Size INTEGER
  brgFilterMask2Offset INTEGER
  brgFilterMask2Value INTEGER
  brgFilterMask2Type INTEGER
  brgFilterMask2Size INTEGER
  brgFilterMask3Offset INTEGER
  brgFilterMask3Value INTEGER
  brgFilterMask3Type INTEGER
  brgFilterMask3Size INTEGER
  brgFilterMask4Offset INTEGER
  brgFilterMask4Value INTEGER
  brgFilterMask4Type INTEGER
  brgFilterMask4Size INTEGER
  brgFilterSkipRii INTEGER

BrgLoggerEntry  
SEQUENCE    
  brgLoggerIndex INTEGER
  brgLoggerName DisplayString Size(0..8)
  brgLoggerType INTEGER
  brgLoggerMask1Offset INTEGER
  brgLoggerMask1Value INTEGER
  brgLoggerMask1Type INTEGER
  brgLoggerMask1Size INTEGER
  brgLoggerMask2Offset INTEGER
  brgLoggerMask2Value INTEGER
  brgLoggerMask2Type INTEGER
  brgLoggerMask2Size INTEGER
  brgLoggerMask3Offset INTEGER
  brgLoggerMask3Value INTEGER
  brgLoggerMask3Type INTEGER
  brgLoggerMask3Size INTEGER
  brgLoggerMask4Offset INTEGER
  brgLoggerMask4Value INTEGER
  brgLoggerMask4Type INTEGER
  brgLoggerMask4Size INTEGER
  brgLoggerSkipRii INTEGER

BrgPLocalEntry  
SEQUENCE    
  brgPLocalIndex INTEGER
  brgPLocalEnabled INTEGER
  brgStpPLocalPriority INTEGER
  brgStpPLocalCost INTEGER
  brgStpPLocalDesigRoot OCTET STRING Size(8)
  brgStpPLocalDesigCost INTEGER
  brgStpPLocalDesigBridge OCTET STRING Size(8)
  brgStpPLocalDesigPath INTEGER
  brgStpPLocalPathState INTEGER

BrgPRmtEntry  
SEQUENCE    
  brgPRmtIndex INTEGER
  brgPRmtEnabled INTEGER
  brgStpPRmtPriority INTEGER
  brgStpPRmtCost INTEGER
  brgStpPRmtDesigRoot OCTET STRING Size(8)
  brgStpPRmtDesigCost INTEGER
  brgStpPRmtDesigBridge OCTET STRING Size(8)
  brgStpPRmtDesigPath INTEGER
  brgStpPRmtPathState INTEGER

BrgLearnedEntry  
SEQUENCE    
  brgLearnedAddress OCTET STRING Size(6)
  brgLearnedPathType INTEGER
  brgLearnedPathIdx INTEGER
  brgLearnedAge INTEGER

AdminUserEntry  
SEQUENCE    
  adminUserIndex INTEGER
  adminUserName DisplayString Size(0..10)
  adminUserType INTEGER
  adminUserPassword OCTET STRING Size(0..8)
  adminUserCallBackPhone OCTET STRING Size(0..15)
  adminEncryptUserPassword OCTET STRING Size(0..16)
  adminEncryptCallBackPhone OCTET STRING Size(0..24)

AdminCommEntry  
SEQUENCE    
  adminCommIndex INTEGER
  adminCommName DisplayString Size(0..10)
  adminCommType INTEGER
  adminCommMgrIpAddress IpAddress
  adminCommMgrIpxNetNumber OCTET STRING Size(4)
  adminCommMgrMacAddress OCTET STRING Size(6)

AdminScriptEntry  
SEQUENCE    
  adminScriptIndex INTEGER
  adminScriptName DisplayString Size(0..16)
  adminScriptType INTEGER
  adminScript OCTET STRING Size(0..527)

AdminRpaLogEntry  
SEQUENCE    
  adminRpaLogIndex INTEGER
  adminRpaLogUserName DisplayString Size(0..10)
  adminRpaLogTime DisplayString Size(0..8)
  adminRpaLogDuration DisplayString Size(0..8)
  adminRpaLogAttempts Counter
  adminRpaLogInPackets Counter
  adminRpaLogOutPackets Counter
  adminRpaLogInBytes Counter
  adminRpaLogOutBytes Counter
  adminRpaLogParityErrors Counter
  adminRpaLogFrameErrors Counter
  adminRpaLogOverrunErrors Counter
  adminRpaLogCksumErrors Counter
  adminRpaLogDate DisplayString Size(0..8)
  adminRpaLogPortName DisplayString Size(0..40)
  adminRpaLogPathName DisplayString Size(0..12)

AdminMdSetupEntry  
SEQUENCE    
  adminMdSetupIndex INTEGER
  adminMdSetupType INTEGER
  adminMdSetupName DisplayString Size(0..16)
  adminMdSetupATCmd DisplayString Size(0..79)
  adminMdSetupARAP1-0ATCmd DisplayString Size(0..79)
  adminMdSetupIncomingCall INTEGER
  adminMdSetupConnIndication INTEGER
  adminMdSetupCallTimeOut INTEGER
  adminMdSetupCallDelay INTEGER

AdminCallerIDEntry  
SEQUENCE    
  adminCallerIDIndex INTEGER
  adminCallerIDName DisplayString Size(0..20)
  adminCallerIDType INTEGER
  adminCallerIDComment DisplayString Size(0..10)

AtRpaEntry  
SEQUENCE    
  atRpaIndex INTEGER
  atRpaNetworkAddress OCTET STRING Size(3)
  atRpaState INTEGER

AtPLocalEntry  
SEQUENCE    
  atPLocalIndex INTEGER
  atPLocalNetAddress OCTET STRING Size(3)
  atPLocalNetStart INTEGER
  atPLocalNetEnd INTEGER
  atPLocalDefaultRouter OCTET STRING Size(3)
  atPLocalLocalZone OCTET STRING Size(0..32)

AtAarpEntry  
SEQUENCE    
  atAarpIfIndex INTEGER
  atAarpPhysAddress OCTET STRING Size(6)
  atAarpNetAddress OCTET STRING Size(3)

AtBestRouterCacheEntry  
SEQUENCE    
  atBestRouterCacheIfIndex INTEGER
  atBestRouterCachePhysAddress OCTET STRING Size(6)
  atBestRouterCacheNetAddress OCTET STRING Size(3)

AtZoneFilterEntry  
SEQUENCE    
  atZoneFilterIndex INTEGER
  atZoneFilterName DisplayString Size(0..32)
  atZoneFilterType INTEGER

Defined Values

centrum 1.3.6.1.4.1.327
OBJECT IDENTIFIER    

mibDoc 1.3.6.1.4.1.327.1
OBJECT IDENTIFIER    

centrumRemote 1.3.6.1.4.1.327.1.1
OBJECT IDENTIFIER    

port 1.3.6.1.4.1.327.1.1.1
OBJECT IDENTIFIER    

path 1.3.6.1.4.1.327.1.1.2
OBJECT IDENTIFIER    

crip 1.3.6.1.4.1.327.1.1.3
OBJECT IDENTIFIER    

ipx 1.3.6.1.4.1.327.1.1.4
OBJECT IDENTIFIER    

brg 1.3.6.1.4.1.327.1.1.5
OBJECT IDENTIFIER    

admin 1.3.6.1.4.1.327.1.1.6
OBJECT IDENTIFIER    

crat 1.3.6.1.4.1.327.1.1.7
OBJECT IDENTIFIER    

portNumber 1.3.6.1.4.1.327.1.1.1.1
The number of communication ports (not including console port) on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portTable 1.3.6.1.4.1.327.1.1.1.2
Remote PC access path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortEntry

portEntry 1.3.6.1.4.1.327.1.1.1.2.1
A path to a remote PC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortEntry  

portIndex 1.3.6.1.4.1.327.1.1.1.2.1.1
A sequentially assigned index value for each communication port on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portId 1.3.6.1.4.1.327.1.1.1.2.1.2
The type of port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER msEthernet(1), s1Ethernet(2), s1Sync(3), s1Async1(4), s1Async2(5), s1Async3(6), s1Async4(7), s1Async5(8), s1Async6(9), s1Async7(10), s1Async8(11), s2Ethernet(12), s2Sync(13), s2Async1(14), s2Async2(15), s2Async3(16), s2Async4(17), s2Async5(18), s2Async6(19), s2Async7(20), s2Async8(21), msTokenRing(22), port1(30), port2(31), port3(32), port4(33), port5(34), port6(35), port7(36), port8(37), s1Br1B1(50), s1Br1B2(51), s1Br2B1(52), s1Br2B2(53), s1Br3B1(54), s1Br3B2(55), s1Br4B1(56), s1Br4B2(57), s2Br1B1(58), s2Br1B2(59), s2Br2B1(60), s2Br2B2(61), s2Br3B1(62), s2Br3B2(63), s2Br4B1(64), s2Br4B2(65)  

portSlot 1.3.6.1.4.1.327.1.1.1.2.1.3
The slot that this port is on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portScriptIdx 1.3.6.1.4.1.327.1.1.1.2.1.4
This index identifies the modem dial in/out script to be used by this async port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portBaudrate 1.3.6.1.4.1.327.1.1.1.2.1.5
Baudrate of this async/sync port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER baud-2400(24), baud-4800(48), baud-9600(96), baud-19200(192), baud-38400(384), baud-56000(560), baud-57600(576), baud-115200(1152)  

portParity 1.3.6.1.4.1.327.1.1.1.2.1.6
Parity of this async port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER odd(1), even(2), zero(3), one(4), none(5)  

portStopBits 1.3.6.1.4.1.327.1.1.1.2.1.7
Number of stop bits for this async port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER bit-1(1), bit-15(2), bits-2(3)  

portDataBits 1.3.6.1.4.1.327.1.1.1.2.1.8
Number of data bits for this async port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER bits-5(5), bits-6(6), bits-7(7), bits-8(8)  

portCCSP 1.3.6.1.4.1.327.1.1.1.2.1.9
Enable 3Com's proprietory data compression algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portPPPProbeInterval 1.3.6.1.4.1.327.1.1.1.2.1.10
Time duration in seconds in between two consecutive PPP probing packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portPPPMaxRcvPacketLength 1.3.6.1.4.1.327.1.1.1.2.1.11
Maximum data field length in bytes for PPP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portPPPAsyncCtrlChar 1.3.6.1.4.1.327.1.1.1.2.1.12
Async control character bit-map for PPP link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portPPPProtCompress 1.3.6.1.4.1.327.1.1.1.2.1.14
Enable protocol field compression for PPP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portPPPACCompress 1.3.6.1.4.1.327.1.1.1.2.1.15
Enable address and control field compression for PPP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

portCRCErrors 1.3.6.1.4.1.327.1.1.1.2.1.16
Ethernet packets received with CRC error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portOversizes 1.3.6.1.4.1.327.1.1.1.2.1.17
Ethernet packets received with size bigger than 1500 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portUndersizes 1.3.6.1.4.1.327.1.1.1.2.1.18
Ethernet packets received with size smaller than 64 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portCollisions 1.3.6.1.4.1.327.1.1.1.2.1.19
Ethernet packet transmit failures due to collision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portInPackets 1.3.6.1.4.1.327.1.1.1.2.1.20
Packets received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portOutPackets 1.3.6.1.4.1.327.1.1.1.2.1.21
Packets transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portInBytes 1.3.6.1.4.1.327.1.1.1.2.1.22
Bytes received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portOutBytes 1.3.6.1.4.1.327.1.1.1.2.1.23
Bytes transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portResetPortCounters 1.3.6.1.4.1.327.1.1.1.2.1.24
Writing any value to this variable will reset all port-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portAsyncParityErrors 1.3.6.1.4.1.327.1.1.1.2.1.25
Number of async parity errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portAsyncCharFrameErrors 1.3.6.1.4.1.327.1.1.1.2.1.26
Number of async character framing errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portAsyncOverrunErrors 1.3.6.1.4.1.327.1.1.1.2.1.27
Number of async receive overrun errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portAsyncPktCksumErrors 1.3.6.1.4.1.327.1.1.1.2.1.28
Number of async packet checksum errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portCTSState 1.3.6.1.4.1.327.1.1.1.2.1.29
Current state CTS signal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

portDCDState 1.3.6.1.4.1.327.1.1.1.2.1.30
Current state DCD signal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

portRIState 1.3.6.1.4.1.327.1.1.1.2.1.31
Current state RI signal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

portSyncFcsErrors 1.3.6.1.4.1.327.1.1.1.2.1.32
Number of sync packet FCS errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portSyncMemoryErrors 1.3.6.1.4.1.327.1.1.1.2.1.33
Number of sync memory errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portSyncOverrunErrors 1.3.6.1.4.1.327.1.1.1.2.1.34
Number of sync receive overrun errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portSyncUnderrunErrors 1.3.6.1.4.1.327.1.1.1.2.1.35
Number of sync transmit underrun errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portIPCPState 1.3.6.1.4.1.327.1.1.1.2.1.36
Current connection state of PPP IPCP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

portIPXCPState 1.3.6.1.4.1.327.1.1.1.2.1.37
Current connection state of PPP IPXCP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

portBNCPState 1.3.6.1.4.1.327.1.1.1.2.1.38
Current connection state of PPP BNCP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

portDriverState 1.3.6.1.4.1.327.1.1.1.2.1.39
Current Token Ring interface state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), reset(2), init(3), open(4), online(5)  

portSpeed 1.3.6.1.4.1.327.1.1.1.2.1.40
Current Token Ring speed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER megabyte-4(4), megabyte-16(16)  

portTotalErrors 1.3.6.1.4.1.327.1.1.1.2.1.41
Number of total interface errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portTransmitDiscards 1.3.6.1.4.1.327.1.1.1.2.1.42
Number of packets dropped due to lack of buffers during transmit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portReceiveCongestions 1.3.6.1.4.1.327.1.1.1.2.1.43
Number of packets dropped due to lack of buffers during receive.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portUnknownProtocols 1.3.6.1.4.1.327.1.1.1.2.1.44
Number of packets received with unknown DLC type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portAccessType 1.3.6.1.4.1.327.1.1.1.2.1.45
Access Type for the corresponding port: ui for normal login sequence, arap for AppleTalk, and ppp for ppp's authentication (PAP/CHAP)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), arap1-0(2), router(4)  

portDialHangUp 1.3.6.1.4.1.327.1.1.1.2.1.46
Hang up current connection
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portPortDisabled 1.3.6.1.4.1.327.1.1.1.2.1.47
The variable disables port for dialout function.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portArapCompress 1.3.6.1.4.1.327.1.1.1.2.1.48
The variable for arap compression.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER v42bis(1), off(2)  

portInterFace 1.3.6.1.4.1.327.1.1.1.2.1.49
The variable shows the port interface type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER async(1), sync(2)  


portLEDActivity 1.3.6.1.4.1.327.1.1.1.2.1.51
The variable shows the port activity LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER light(1), medium(2), heavy(3)  

portLEDFault 1.3.6.1.4.1.327.1.1.1.2.1.52
The variable shows the port fault LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

portLinkType 1.3.6.1.4.1.327.1.1.1.2.1.53
The variable shows the ISDN port link type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dial(0), permanent(1)  

portSwitchType 1.3.6.1.4.1.327.1.1.1.2.1.54
The variable shows the ISDN port country type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER att5ess(1), dms100(2), ni1(3), ins64(4), vn3(5), net3(6)  

portSPID-1 1.3.6.1.4.1.327.1.1.1.2.1.55
The variable shows the ISDN port SPID #1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

portSPID-2 1.3.6.1.4.1.327.1.1.1.2.1.56
The variable shows the ISDN port SPID #2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

portDirectoryNo-1 1.3.6.1.4.1.327.1.1.1.2.1.57
The variable shows the ISDN port DirectoryNo #1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

portDirectoryNo-2 1.3.6.1.4.1.327.1.1.1.2.1.58
The variable shows the ISDN port DirectoryNo #2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

portLocalDialNo-1 1.3.6.1.4.1.327.1.1.1.2.1.59
The variable shows the ISDN port LocalDialNo #1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

portLocalDialNo-2 1.3.6.1.4.1.327.1.1.1.2.1.60
The variable shows the ISDN port LocalDialNo #2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

portLocalSubaddress-1 1.3.6.1.4.1.327.1.1.1.2.1.61
The variable shows the ISDN port LocalSubaddress #1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..10)  

portLocalSubaddress-2 1.3.6.1.4.1.327.1.1.1.2.1.62
The variable shows the ISDN port LocalSubaddress #2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..10)  

portProtocolMode 1.3.6.1.4.1.327.1.1.1.2.1.63
The variable shows the ISDN port protocol mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER v-120(4), raw(5)  

portPortReset 1.3.6.1.4.1.327.1.1.1.2.1.64
The variable resets ISDN port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

portIncomingCalls 1.3.6.1.4.1.327.1.1.1.2.1.65
Number of ISDN incoming calls.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portOutgoingCalls 1.3.6.1.4.1.327.1.1.1.2.1.66
Number of ISDN outgoing calls.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portRemoteDialNo 1.3.6.1.4.1.327.1.1.1.2.1.67
The variable shows the ISDN port B channel remote dial no.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..20)  

portRemoteSubaddress 1.3.6.1.4.1.327.1.1.1.2.1.68
The variable shows the ISDN port B channel remote subaddress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

portISDNInterfaceType 1.3.6.1.4.1.327.1.1.1.2.1.69
The variable shows the interface type of the ISDN card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..3)  

portPathName 1.3.6.1.4.1.327.1.1.1.2.1.70
The variable shows the path name on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

portILCCPState 1.3.6.1.4.1.327.1.1.1.2.1.71
This parameter indicates the individual link CCP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

portCurISDNBChannel 1.3.6.1.4.1.327.1.1.1.2.1.72
This parameter indicates the physical binding channel number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER b-1(1), b-2(2)  

portLoginStatus 1.3.6.1.4.1.327.1.1.1.2.1.73
This parameter indicates the login status for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unused(1), dial-in(2), dial-out(3), disabled(4), router(5)  

portLastConnectBChannel 1.3.6.1.4.1.327.1.1.1.2.1.74
This parameter indicates last connect B channel for this ISDN line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-used(1), b-1(2), b-2(3)  

portISDNPhyLineStatus 1.3.6.1.4.1.327.1.1.1.2.1.75
This parameter indicates physical line status for this ISDN line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER deactivated(1), activated(2)  

portTEIState 1.3.6.1.4.1.327.1.1.1.2.1.76
This parameter indicates TEI state for this ISDN line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unassigned(1), assigned(2)  

portLayer3Status 1.3.6.1.4.1.327.1.1.1.2.1.77
This parameter indicates lay 3 status for this ISDN line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER uninitialized(1), initialized(2)  

portResetAllCounters 1.3.6.1.4.1.327.1.1.1.3
Writing any value to this variable will reset all port-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portSourceRouteTable 1.3.6.1.4.1.327.1.1.1.4
Source route information table for end stations.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortSourceRouteEntry

portSourceRouteEntry 1.3.6.1.4.1.327.1.1.1.4.1
A source route path to an end station.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortSourceRouteEntry  

portSRMacAddress 1.3.6.1.4.1.327.1.1.1.4.1.1
MAC address of the Source Route table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

portSRState 1.3.6.1.4.1.327.1.1.1.4.1.2
Source Route path state of the Source Route table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER empty(0), pending(1), new(2), old(3)  

portSRTimeToLive 1.3.6.1.4.1.327.1.1.1.4.1.3
Time to live information of the Source Route table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portSRLargestFrame 1.3.6.1.4.1.327.1.1.1.4.1.4
Largest frame information of the Source Route table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portSRDirection 1.3.6.1.4.1.327.1.1.1.4.1.5
Path direction of the Source Route table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER forward(0), backword(1)  

portSRRouteDescrpt 1.3.6.1.4.1.327.1.1.1.4.1.6
Path information of the Source Route table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..70)  

portAllLoginStatus 1.3.6.1.4.1.327.1.1.1.5
This parameter indicates the login status for all ports. The format is the sequence of portID and login status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

portTokenRingSpeed 1.3.6.1.4.1.327.1.1.1.6
Current Token Ring speed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER megabyte-4(4), megabyte-16(16)  

portAllLEDStatus 1.3.6.1.4.1.327.1.1.1.7
This parameter indicates the led status for all ports. The format is the sequence of portID, Link LED, Activity LED and Fault LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

prpaNumber 1.3.6.1.4.1.327.1.1.2.1
The number of remote PC access paths on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

prpaTable 1.3.6.1.4.1.327.1.1.2.2
Remote PC access path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrpaEntry

prpaEntry 1.3.6.1.4.1.327.1.1.2.2.1
A path to a remote PC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PrpaEntry  

prpaIndex 1.3.6.1.4.1.327.1.1.2.2.1.1
A unique value for each remote PC access path. The value for each path must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

prpaName 1.3.6.1.4.1.327.1.1.2.2.1.2
A unique user-recognizable name for each remote PC access path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

prpaType 1.3.6.1.4.1.327.1.1.2.2.1.3
The type of path. Invalid means this path no longer exists.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

prpaPortIdx 1.3.6.1.4.1.327.1.1.2.2.1.4
A number to uniquely identify a port for this remote PC access path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

prpaAutoHangUp 1.3.6.1.4.1.327.1.1.2.2.1.5
This flag indicates whether Auto-hangup feature is enabled. If enabled, the line will be disconnected if no traffic activity has been detected for default time interval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

prpaInPackets 1.3.6.1.4.1.327.1.1.2.2.1.6
Packets received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaOutPackets 1.3.6.1.4.1.327.1.1.2.2.1.7
Packets transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaInBytes 1.3.6.1.4.1.327.1.1.2.2.1.8
Bytes received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaOutBytes 1.3.6.1.4.1.327.1.1.2.2.1.9
Bytes transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaResetPrpaCounters 1.3.6.1.4.1.327.1.1.2.2.1.10
Writing any value to this variable will reset all prpa-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prpaLoginStatus 1.3.6.1.4.1.327.1.1.2.2.1.11
Login status of this RPA path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unused(0), dial-in(1), dial-out(2), disabled(3)  

prpaLoginUserName 1.3.6.1.4.1.327.1.1.2.2.1.12
The name of the currently logged-in user.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

prpaLoginTime 1.3.6.1.4.1.327.1.1.2.2.1.13
The start time (in HH:MM:SS) of current session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

prpaLoginDuration 1.3.6.1.4.1.327.1.1.2.2.1.14
The elapsed time (in HH:MM:SS) of current session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

prpaLoginAttempts 1.3.6.1.4.1.327.1.1.2.2.1.15
Number of unsuccessful login attempts in this authentication process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaLoginInPackets 1.3.6.1.4.1.327.1.1.2.2.1.16
Number of correctly received packets in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaLoginOutPackets 1.3.6.1.4.1.327.1.1.2.2.1.17
Number of correctly transmitted packets in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaLoginInBytes 1.3.6.1.4.1.327.1.1.2.2.1.18
Number of correctly received bytes in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaLoginOutBytes 1.3.6.1.4.1.327.1.1.2.2.1.19
Number of correctly transmitted bytes in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaLoginParityErrors 1.3.6.1.4.1.327.1.1.2.2.1.20
Number of characters received with parity error in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaLoginFrameErrors 1.3.6.1.4.1.327.1.1.2.2.1.21
Number of characters received with framing error in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaLoginOverrunErrors 1.3.6.1.4.1.327.1.1.2.2.1.22
Number of receive overrun errors in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaLoginCksumErrors 1.3.6.1.4.1.327.1.1.2.2.1.23
Number of incoming pakets with bad checksum in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaFilterAction 1.3.6.1.4.1.327.1.1.2.2.1.24
The action to be taken by the configured this path's filters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER discard(1), forward(2)  

prpaFilterMap 1.3.6.1.4.1.327.1.1.2.2.1.25
This is a 16 bit bitmap corresponds to the bridge filter table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prpaLoggerMap 1.3.6.1.4.1.327.1.1.2.2.1.26
This is a 16 bit bitmap corresponds to the bridge logger table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prpaFilterCount 1.3.6.1.4.1.327.1.1.2.2.1.27
The number of packets that have been filtered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaLoggerCount 1.3.6.1.4.1.327.1.1.2.2.1.28
The value gives the number of incoming packets that match this log description.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaDiscardedPackets 1.3.6.1.4.1.327.1.1.2.2.1.29
Packets discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaForwardedPackets 1.3.6.1.4.1.327.1.1.2.2.1.30
Packets forwarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaReceivedPackets 1.3.6.1.4.1.327.1.1.2.2.1.31
Packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prpaSmartFiltering 1.3.6.1.4.1.327.1.1.2.2.1.32
This enables/disables AccessBuilder's Smart Filtering feature.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

prpaCurrentMacAddr 1.3.6.1.4.1.327.1.1.2.2.1.33
This parameter displays the remote client's MAC address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

prpaIpEthernetII 1.3.6.1.4.1.327.1.1.2.2.1.34
This parameter indicates the protocol IP EthernetII running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaIpSnap 1.3.6.1.4.1.327.1.1.2.2.1.35
This parameter indicates the protocol IP Snap running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaRemotePcIpAddress 1.3.6.1.4.1.327.1.1.2.2.1.36
This parameter indicates the IP address running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

prpaIpxEn2WithNetBIOS 1.3.6.1.4.1.327.1.1.2.2.1.37
This parameter indicates the protocol IPX EthernetII with NetBIOS running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaIpx8023WithNetBIOS 1.3.6.1.4.1.327.1.1.2.2.1.38
This parameter indicates the protocol IPX 802.3 with NetBIOS running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaIpx8022WithNetBIOS 1.3.6.1.4.1.327.1.1.2.2.1.39
This parameter indicates the protocol IPX 802.2 with NetBIOS running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaIpxSnapWithNetBIOS 1.3.6.1.4.1.327.1.1.2.2.1.40
This parameter indicates the protocol IPX Snap with NetBIOS running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaXNS 1.3.6.1.4.1.327.1.1.2.2.1.41
This parameter indicates the protocol XNS running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaVinesEthernetII 1.3.6.1.4.1.327.1.1.2.2.1.42
This parameter indicates the protocol Vines EthernetII running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaVinesSnap 1.3.6.1.4.1.327.1.1.2.2.1.43
This parameter indicates the protocol Vines Snap running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaNetBIOS 1.3.6.1.4.1.327.1.1.2.2.1.44
This parameter indicates the protocol NetBIOS running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaDECNet 1.3.6.1.4.1.327.1.1.2.2.1.45
This parameter indicates the protocol DECNET running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaUnknowEthernetII 1.3.6.1.4.1.327.1.1.2.2.1.46
This parameter indicates the protocol Unknown EthernetII running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaUnknownSap 1.3.6.1.4.1.327.1.1.2.2.1.47
This parameter indicates the protocol Unknown Sap running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaUnknownSnap 1.3.6.1.4.1.327.1.1.2.2.1.48
This parameter indicates the protocol Unknown Snap running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaMulticastAddress 1.3.6.1.4.1.327.1.1.2.2.1.49
This parameter indicates the multicast address packets recongnized by the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

prpaXNSSap 1.3.6.1.4.1.327.1.1.2.2.1.50
This parameter indicates the protocol XNS Sap running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaXNSSnap 1.3.6.1.4.1.327.1.1.2.2.1.51
This parameter indicates the protocol XNS Snap running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaVinesSap 1.3.6.1.4.1.327.1.1.2.2.1.52
This parameter indicates the protocol Vines Sap running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaIpxEn2 1.3.6.1.4.1.327.1.1.2.2.1.53
This parameter indicates the protocol IPX EthernetII running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaIpx8023 1.3.6.1.4.1.327.1.1.2.2.1.54
This parameter indicates the protocol IPX 802.3 running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaIpx8022 1.3.6.1.4.1.327.1.1.2.2.1.55
This parameter indicates the protocol IPX 802.2 running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaIpxSnap 1.3.6.1.4.1.327.1.1.2.2.1.56
This parameter indicates the protocol IPX Snap running in the remotepc client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

prpaPortList 1.3.6.1.4.1.327.1.1.2.2.1.57
This parameter indicates the port-id list for the binding ports on this RPA path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..48)  

prpaSpoofState 1.3.6.1.4.1.327.1.1.2.2.1.58
This parameter indicates the spoofing state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), connect(2), spoofing(3), disabled(4)  

prpaCCPState 1.3.6.1.4.1.327.1.1.2.2.1.59
This parameter indicates the CCP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

prpaIPCPState 1.3.6.1.4.1.327.1.1.2.2.1.60
This parameter indicates the IPCP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

prpaIPXCPState 1.3.6.1.4.1.327.1.1.2.2.1.61
This parameter indicates the IPXCP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

prpaBNCPState 1.3.6.1.4.1.327.1.1.2.2.1.62
This parameter indicates the BNCP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

prpaARAPState 1.3.6.1.4.1.327.1.1.2.2.1.63
This parameter indicates the ARAP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

prpaLinkUtil 1.3.6.1.4.1.327.1.1.2.2.1.64
This parameter indicates the link utilization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

plocalNumber 1.3.6.1.4.1.327.1.1.2.3
The number of local route paths on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

plocalTable 1.3.6.1.4.1.327.1.1.2.4
Local route path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PlocalEntry

plocalEntry 1.3.6.1.4.1.327.1.1.2.4.1
A list of information for a local route path.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PlocalEntry  

plocalIndex 1.3.6.1.4.1.327.1.1.2.4.1.1
A unique value for each network route path. The value for each path must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

plocalName 1.3.6.1.4.1.327.1.1.2.4.1.2
A unique user-recognizable name for each local route path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

plocalType 1.3.6.1.4.1.327.1.1.2.4.1.3
The variable indicates whether this local route path entry is currently effective.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

plocalPortIdx 1.3.6.1.4.1.327.1.1.2.4.1.4
A number to uniquely identify a port for this local route path. The port that is identified by this index is the as the port identified by PortIndex in portTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

plocalInPackets 1.3.6.1.4.1.327.1.1.2.4.1.5
Packets received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

plocalOutPackets 1.3.6.1.4.1.327.1.1.2.4.1.6
Packets transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

plocalInBytes 1.3.6.1.4.1.327.1.1.2.4.1.7
Bytes received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

plocalOutBytes 1.3.6.1.4.1.327.1.1.2.4.1.8
Bytes transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

plocalResetPlocalCounters 1.3.6.1.4.1.327.1.1.2.4.1.9
Writing any value to this variable will reset all plocal-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

plocalFilterAction 1.3.6.1.4.1.327.1.1.2.4.1.10
The action to be taken by the configured this path's filters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER discard(1), forward(2)  

plocalFilterMap 1.3.6.1.4.1.327.1.1.2.4.1.11
This is a 16 bit bitmap corresponds to the bridge filetr table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

plocalLoggerMap 1.3.6.1.4.1.327.1.1.2.4.1.12
This is a 16 bit bitmap corresponds to the bridge logger table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

plocalFilterCount 1.3.6.1.4.1.327.1.1.2.4.1.13
The number of packets that have been filtered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

plocalLoggerCount 1.3.6.1.4.1.327.1.1.2.4.1.14
The value gives the number of incoming packets that match this log description.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

plocalDiscardedPackets 1.3.6.1.4.1.327.1.1.2.4.1.15
Packets discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

plocalForwardedPackets 1.3.6.1.4.1.327.1.1.2.4.1.16
Packets forwarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

plocalReceivedPackets 1.3.6.1.4.1.327.1.1.2.4.1.17
Packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtNumber 1.3.6.1.4.1.327.1.1.2.5
The number of route paths on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

prmtTable 1.3.6.1.4.1.327.1.1.2.6
Route path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrmtEntry

prmtEntry 1.3.6.1.4.1.327.1.1.2.6.1
A list of information for a route path.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PrmtEntry  

prmtIndex 1.3.6.1.4.1.327.1.1.2.6.1.1
A unique value for each network route path. The value for each path must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

prmtName 1.3.6.1.4.1.327.1.1.2.6.1.2
A unique user-recognizable name for each remote PC access path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..12)  

prmtType 1.3.6.1.4.1.327.1.1.2.6.1.3
The variable indicates whether this remote route path entry is currently effective.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

prmtInitiator 1.3.6.1.4.1.327.1.1.2.6.1.4
Used on remote path only. This flag tells whether this side should initiate the connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), passive(2)  

prmtCongestThreshold 1.3.6.1.4.1.327.1.1.2.6.1.5
Used on remote paths with on-demand ports only. It is used to determine when a on-demand port be started.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prmtScheduleType1 1.3.6.1.4.1.327.1.1.2.6.1.6
The variable is meaningful only on paths with schedule port. It described the port's schedule type - daily, weekly or monthly.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), daily(2), weekly(3), monthly(4)  

prmtDaysScheduled1 1.3.6.1.4.1.327.1.1.2.6.1.7
The variable is meaningful only on paths with schedule port. A bit map of days on which each '1' bit represents a day that the port will be scheduled. The least significant bit indicates the 1st day in a period (for week, it's Monday; for month, it's the first day in a month.)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prmtStartTime1 1.3.6.1.4.1.327.1.1.2.6.1.8
The variable is meaningful only on paths with schedule port. This describes the scheduled port connection period in StartHour:StartMinute format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

prmtHowLong1 1.3.6.1.4.1.327.1.1.2.6.1.9
The variable is meaningful only on paths with schedule port. This describes the scheduled port connection period in DurationHour:DurationMinute format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

prmtScheduleType2 1.3.6.1.4.1.327.1.1.2.6.1.10
The variable is meaningful only on paths with schedule port. It described the port's schedule type - daily, weekly or monthly.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), daily(2), weekly(3), monthly(4)  

prmtDaysScheduled2 1.3.6.1.4.1.327.1.1.2.6.1.11
The variable is meaningful only on paths with schedule port. A bit map of days on which each '1' bit represents a day that the port will be scheduled. The least significant bit indicates the 1st day in a period (for week, it's Monday; for month, it's the first day in a month.)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prmtStartTime2 1.3.6.1.4.1.327.1.1.2.6.1.12
The variable is meaningful only on paths with schedule port. This describes the scheduled port connection period in StartHour:StartMinute format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

prmtHowLong2 1.3.6.1.4.1.327.1.1.2.6.1.13
The variable is meaningful only on paths with schedule port. This describes the scheduled port connection period in DurationHour:DurationMinute format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

prmtInPackets 1.3.6.1.4.1.327.1.1.2.6.1.14
Packets received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtOutPackets 1.3.6.1.4.1.327.1.1.2.6.1.15
Packets transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtInBytes 1.3.6.1.4.1.327.1.1.2.6.1.16
Bytes received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtOutBytes 1.3.6.1.4.1.327.1.1.2.6.1.17
Bytes transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtResetPrmtCounters 1.3.6.1.4.1.327.1.1.2.6.1.18
Writing any value to this variable will reset all prmt-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prmtFilterAction 1.3.6.1.4.1.327.1.1.2.6.1.19
The action to be taken by the configured this path's filters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER discard(1), forward(2)  

prmtFilterMap 1.3.6.1.4.1.327.1.1.2.6.1.20
This is a 16 bit bitmap corresponds to the bridge filetr table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prmtLoggerMap 1.3.6.1.4.1.327.1.1.2.6.1.21
This is a 16 bit bitmap corresponds to the bridge logger table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prmtFilterCount 1.3.6.1.4.1.327.1.1.2.6.1.22
The number of packets that have been filtered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtLoggerCount 1.3.6.1.4.1.327.1.1.2.6.1.23
The value gives the number of incoming packets that match this log description.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtDiscardedPackets 1.3.6.1.4.1.327.1.1.2.6.1.24
Packets discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtForwardedPackets 1.3.6.1.4.1.327.1.1.2.6.1.25
Packets forwarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtReceivedPackets 1.3.6.1.4.1.327.1.1.2.6.1.26
Packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtSmartFiltering 1.3.6.1.4.1.327.1.1.2.6.1.27
This enables/disables AccessBuilder's Smart Filtering feature.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

prmtOutCongestions 1.3.6.1.4.1.327.1.1.2.6.1.28
Number of packet transmit congestions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

prmtRmtRouterName 1.3.6.1.4.1.327.1.1.2.6.1.29
Remote router name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

prmtTypeSelection 1.3.6.1.4.1.327.1.1.2.6.1.30
Path type selection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER permanent-only(1), permanent-with-backup(2), on-demand-only(3), schedule-only(4)  

prmtAsyncPortNo 1.3.6.1.4.1.327.1.1.2.6.1.31
Number of async ports for Backup, On-demand and Schedule type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prmtISDNPortNo 1.3.6.1.4.1.327.1.1.2.6.1.32
Number of ISDN ports for Backup, On-demand and Schedule type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prmtISDNReqBaudRate 1.3.6.1.4.1.327.1.1.2.6.1.33
ISDN required baudrate for satisfying all cases.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER br-56000(1), br-64000(2), auto(3)  

prmtSpoofState 1.3.6.1.4.1.327.1.1.2.6.1.34
This parameter indicates the spoofing state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), connect(2), spoofing(3), disabled(4)  

prmtCCPState 1.3.6.1.4.1.327.1.1.2.6.1.35
This parameter indicates the CCP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

prmtIPCPState 1.3.6.1.4.1.327.1.1.2.6.1.36
This parameter indicates the IPCP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

prmtIPXCPState 1.3.6.1.4.1.327.1.1.2.6.1.37
This parameter indicates the IPXCP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

prmtBNCPState 1.3.6.1.4.1.327.1.1.2.6.1.38
This parameter indicates the BNCP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

prmtLinkUtil 1.3.6.1.4.1.327.1.1.2.6.1.39
This parameter indicates the link utilization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

prmtPMPortList 1.3.6.1.4.1.327.1.1.2.6.1.40
This parameter indicates the port-id list for the binding permenant ports on this Remote path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..48)  

prmtBUPortList 1.3.6.1.4.1.327.1.1.2.6.1.41
This parameter indicates the port-id list for the binding backup ports on this Remote path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..48)  

prmtODPortList 1.3.6.1.4.1.327.1.1.2.6.1.42
This parameter indicates the port-id list for the binding on-demand ports on this Remote path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..48)  

prmtSCPortList 1.3.6.1.4.1.327.1.1.2.6.1.43
This parameter indicates the port-id list for the binding schedule ports on this Remote path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..48)  

prmtPortTable 1.3.6.1.4.1.327.1.1.2.7
Route path port table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrmtPortEntry

prmtPortEntry 1.3.6.1.4.1.327.1.1.2.7.1
A list of information for each port associated with a route path.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PrmtPortEntry  

prmtPortPrmtIdx 1.3.6.1.4.1.327.1.1.2.7.1.1
The route path on which this entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of prmtIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

prmtPortPortIdx 1.3.6.1.4.1.327.1.1.2.7.1.2
The port on which the entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of portIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

prmtPortType 1.3.6.1.4.1.327.1.1.2.7.1.3
Used on remote path only. This vaiable tells the type of port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), on-demand(2), permanent(3), backup(4), scheduled(5)  

prmtPortPhoneNumber 1.3.6.1.4.1.327.1.1.2.7.1.4
Used on remote path only. The phone number to be used by this type of port in the path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..15)  

prmtPortDirectoryNo 1.3.6.1.4.1.327.1.1.2.7.1.5
Used on remote path only. The directory number to be used by this type of port in the path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..20)  

pathResetAllCounters 1.3.6.1.4.1.327.1.1.2.8
Writing any value to this variable will reset all path-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

prmtPhoneTable 1.3.6.1.4.1.327.1.1.2.9
Router path phone table for Backup, On-demand and Schedule type.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PrmtPhoneEntry

prmtPhoneEntry 1.3.6.1.4.1.327.1.1.2.9.1
A list of phone data for each port associated with a route path.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PrmtPhoneEntry  

prmtPhonePrmtIdx 1.3.6.1.4.1.327.1.1.2.9.1.1
Path index for phone table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

prmtPhoneIdx 1.3.6.1.4.1.327.1.1.2.9.1.2
Phone table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

prmtPhoneType 1.3.6.1.4.1.327.1.1.2.9.1.3
Phone type for remote path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), on-demand-isdn(2), on-demand-async(3), backup-isdn(4), backup-async(5), scheduled-isdn(6), scheduled-async(7)  

prmtPhonePhoneNumber 1.3.6.1.4.1.327.1.1.2.9.1.4
Phone number in the phone table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..15)  

prmtPhoneDirectoryNo 1.3.6.1.4.1.327.1.1.2.9.1.5
Directory number in the phone table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..20)  

ipRpa 1.3.6.1.4.1.327.1.1.3.1
OBJECT IDENTIFIER    

ipRt 1.3.6.1.4.1.327.1.1.3.2
OBJECT IDENTIFIER    

ipRpaNumber 1.3.6.1.4.1.327.1.1.3.1.1
The number of IP remote PC paths on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipRpaTable 1.3.6.1.4.1.327.1.1.3.1.2
Remote PC access path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpRpaEntry

ipRpaEntry 1.3.6.1.4.1.327.1.1.3.1.2.1
A path to a remote PC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpRpaEntry  

ipRpaIndex 1.3.6.1.4.1.327.1.1.3.1.2.1.1
The RPA path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same RPA path as identified by the same value of prpaIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipRpaCurrentClientIpAddress 1.3.6.1.4.1.327.1.1.3.1.2.1.2
The current or last logged-in SLIP remote PC's IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipRpaConfigClientIpAddress 1.3.6.1.4.1.327.1.1.3.1.2.1.3
The administrator-assigned PPP remote PC's IP address. This is the IP address to be used by any PPP remote PC dial in to this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipRpaTcpHdrCompress 1.3.6.1.4.1.327.1.1.3.1.2.1.4
The VJ Compression (RFC 1144 TCP/IP Header Compression) of the PPP
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipRpaType 1.3.6.1.4.1.327.1.1.3.1.2.1.5
The type of iprpath. Invalid means this path no longer exists.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ipRpaBootpEnabled 1.3.6.1.4.1.327.1.1.3.1.3
The variable enables BootP server on the AccessBuilder.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipRpaRarpEnabled 1.3.6.1.4.1.327.1.1.3.1.4
The variable enables Reverse ARP server on the AccessBuilder.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipRpaBootpOrRarpRequired 1.3.6.1.4.1.327.1.1.3.1.5
The variable forces remote clients to run BootP or Reverse ARP protocol before accessing IP hosts on the network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipRpaBootpInPackets 1.3.6.1.4.1.327.1.1.3.1.6
BootP packets received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipRpaBootpOutPackets 1.3.6.1.4.1.327.1.1.3.1.7
BootP packets sent with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipRpaRarpInPackets 1.3.6.1.4.1.327.1.1.3.1.8
Reverse ARP packets received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipRpaRarpOutPackets 1.3.6.1.4.1.327.1.1.3.1.9
Reverse ARP packets sent with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipRpaResetAllRasCounters 1.3.6.1.4.1.327.1.1.3.1.10
Writing any value to this variable will reset all Bootp and Reverse ARP counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipRpaPRPAIpHdrCompress 1.3.6.1.4.1.327.1.1.3.1.11
Turn on/off IP header compression for remote access path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipSRouteNumber 1.3.6.1.4.1.327.1.1.3.2.1
The number of IP static routes on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipSRouteTable 1.3.6.1.4.1.327.1.1.3.2.2
IP static route table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpSRouteEntry

ipSRouteEntry 1.3.6.1.4.1.327.1.1.3.2.2.1
A list of information for each static route.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpSRouteEntry  

ipSRouteIndex 1.3.6.1.4.1.327.1.1.3.2.2.1.1
A statics route number of the static route for which the entry contains the route's information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipSRouteName 1.3.6.1.4.1.327.1.1.3.2.2.1.2
An user-defined name for the static route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

ipSRouteType 1.3.6.1.4.1.327.1.1.3.2.2.1.3
The variable indicates whether this static route entry is currently effective.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ipSRoutePathType 1.3.6.1.4.1.327.1.1.3.2.2.1.4
The variable indicates which route path table (local or remote) this route uses.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

ipSRoutePathIdx 1.3.6.1.4.1.327.1.1.3.2.2.1.5
The route path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of plocalIndex or prmtIndex depending on path type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipSRouteDestIpAddress 1.3.6.1.4.1.327.1.1.3.2.2.1.6
The destination network's IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipSRouteNextRouter 1.3.6.1.4.1.327.1.1.3.2.2.1.7
The next router's IP address in this route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipSRouteHopCount 1.3.6.1.4.1.327.1.1.3.2.2.1.8
Number of hop needed to get to the destination network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipPLocalNumber 1.3.6.1.4.1.327.1.1.3.2.3
The number of IP dynamic routes on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipPLocalTable 1.3.6.1.4.1.327.1.1.3.2.4
IP dynamic route table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpPLocalEntry

ipPLocalEntry 1.3.6.1.4.1.327.1.1.3.2.4.1
A list of information for a IP dynamic route.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpPLocalEntry  

ipPLocalIndex 1.3.6.1.4.1.327.1.1.3.2.4.1.1
The route path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of plocalIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipPLocalIpAddress 1.3.6.1.4.1.327.1.1.3.2.4.1.2
This path's IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipPLocalNetMask 1.3.6.1.4.1.327.1.1.3.2.4.1.3
The netmask of the network that is attached to the path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipPLocalBcastAddr 1.3.6.1.4.1.327.1.1.3.2.4.1.4
The least significant bit of the IP broadcast address to network that is attached to the path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER zero-based(0), one-based(1)  

ipPRmtNumber 1.3.6.1.4.1.327.1.1.3.2.5
The number of IP dynamic routes on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipPRmtTable 1.3.6.1.4.1.327.1.1.3.2.6
IP dynamic route table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpPRmtEntry

ipPRmtEntry 1.3.6.1.4.1.327.1.1.3.2.6.1
A list of information for a IP dynamic route.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpPRmtEntry  

ipPRmtIndex 1.3.6.1.4.1.327.1.1.3.2.6.1.1
The route path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of prmtIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipPRmtIpAddress 1.3.6.1.4.1.327.1.1.3.2.6.1.2
This path's IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipPRmtNetMask 1.3.6.1.4.1.327.1.1.3.2.6.1.3
The netmask of the network that is attached to the path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipPRmtBcastAddr 1.3.6.1.4.1.327.1.1.3.2.6.1.4
The least significant bit of the IP broadcast address to network that is attached to the path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER zero-based(0), one-based(1)  

ipPRmtRipUpdate 1.3.6.1.4.1.327.1.1.3.2.6.1.5
The method of sending IP RIP packets and updating routing database for this path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), trigger-update(2), periodic-update(3)  

ipPRmtType 1.3.6.1.4.1.327.1.1.3.2.6.1.6
Indication of validity of this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ipPRmtTcpHdrCompress 1.3.6.1.4.1.327.1.1.3.2.6.1.7
The VJ Compression (TCP/IP Header Compression) of the PPP
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipRtUpdateTime 1.3.6.1.4.1.327.1.1.3.2.7
The time interval (in seconds) at which the routing information is being updated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipRtRipEnabled 1.3.6.1.4.1.327.1.1.3.2.8
RIP protocol enable/disable flag.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipRtEnabled 1.3.6.1.4.1.327.1.1.3.2.9
Router function enable/disable flag.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipRtDefaultTTL 1.3.6.1.4.1.327.1.1.3.2.10
The default time-to-live value for IP messages.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipRtPoisonReverse 1.3.6.1.4.1.327.1.1.3.2.11
This flag tells whether to enable Poison-Reverse feature in RIP protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ipRtResetAllCounters 1.3.6.1.4.1.327.1.1.3.2.12
Writing any value to this variable will reset all port-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipRtInPackets 1.3.6.1.4.1.327.1.1.3.2.13
IP packets received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipRtOutPackets 1.3.6.1.4.1.327.1.1.3.2.14
IP packets transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipRtDefaultRouterAddress 1.3.6.1.4.1.327.1.1.3.2.15
The default router's IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipRtDefaultRouterPathType 1.3.6.1.4.1.327.1.1.3.2.16
The variable indicates which route path table (local or remote) this route uses.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

ipRtDefaultRouterPathIdx 1.3.6.1.4.1.327.1.1.3.2.17
The variable indicates the index to the path table (local or remote) this route uses.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipRtDiscardNBBcastPkts 1.3.6.1.4.1.327.1.1.3.2.18
The variable indicates to discard or forward the NETBIOS broadcast packets to remote dial-in ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxRpa 1.3.6.1.4.1.327.1.1.4.1
OBJECT IDENTIFIER    

ipxRt 1.3.6.1.4.1.327.1.1.4.2
OBJECT IDENTIFIER    

ipxRpaNetNumber 1.3.6.1.4.1.327.1.1.4.1.1
The IPX network address for all RPA paths.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(4)  

ipxRpaNumber 1.3.6.1.4.1.327.1.1.4.1.2
The number of IPX remote PC paths on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxRpaTable 1.3.6.1.4.1.327.1.1.4.1.3
IPX Remote PC access path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpxRpaEntry

ipxRpaEntry 1.3.6.1.4.1.327.1.1.4.1.3.1
A path to a IPX remote PC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpxRpaEntry  

ipxRpaIndex 1.3.6.1.4.1.327.1.1.4.1.3.1.1
The RPA path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same RPA path as identified by the same value of prpaIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxRpaCurrHostAddr 1.3.6.1.4.1.327.1.1.4.1.3.1.2
Current IPX Host Address
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

ipxSRouteNumber 1.3.6.1.4.1.327.1.1.4.2.1
The number of IPX static routes on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxSRouteTable 1.3.6.1.4.1.327.1.1.4.2.2
IPX static route table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpxSRouteEntry

ipxSRouteEntry 1.3.6.1.4.1.327.1.1.4.2.2.1
A list of information for a IPX static route.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpxSRouteEntry  

ipxSRouteIndex 1.3.6.1.4.1.327.1.1.4.2.2.1.1
A statics route number of the IPX static route for which the entry contains the route's information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxSRouteName 1.3.6.1.4.1.327.1.1.4.2.2.1.2
An user-defined name for the static route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

ipxSRouteType 1.3.6.1.4.1.327.1.1.4.2.2.1.3
The variable indicates whether this static route entry is currently effective.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ipxSRoutePathType 1.3.6.1.4.1.327.1.1.4.2.2.1.4
The variable indicates which route path table (local or remote) this route uses.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

ipxSRoutePathIdx 1.3.6.1.4.1.327.1.1.4.2.2.1.5
The route path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of plocalIndex or prmtIndex depending on path type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipxSRouteDestNetNumber 1.3.6.1.4.1.327.1.1.4.2.2.1.6
The destination network's IPX network address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(4)  

ipxSRouteNextHostAddress 1.3.6.1.4.1.327.1.1.4.2.2.1.8
The host address of next IPX router in this route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(6)  

ipxSRouteHopCount 1.3.6.1.4.1.327.1.1.4.2.2.1.9
Number of hop needed to get to the destination network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipxPLocalNumber 1.3.6.1.4.1.327.1.1.4.2.3
The number of IPX dynamic routes on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxPLocalTable 1.3.6.1.4.1.327.1.1.4.2.4
IPX dynamic routes table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpxPLocalEntry

ipxPLocalEntry 1.3.6.1.4.1.327.1.1.4.2.4.1
A list of information for an IPX dynamic route.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpxPLocalEntry  

ipxPLocalIndex 1.3.6.1.4.1.327.1.1.4.2.4.1.1
The route path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of plocalIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxPLocalNetNumber 1.3.6.1.4.1.327.1.1.4.2.4.1.2
The network address of the network that is attached to the path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(4)  

ipxPLocalDataLinkType 1.3.6.1.4.1.327.1.1.4.2.4.1.3
For local path only. The type data link header used in this path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ieee8023(1), ethernet(2), snap(3), ieee8022(4), autolearn(5), trsnap(6), trsap(7)  

ipxPRmtNumber 1.3.6.1.4.1.327.1.1.4.2.5
The number of IPX dynamic routes on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxPRmtTable 1.3.6.1.4.1.327.1.1.4.2.6
IPX dynamic routes table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpxPRmtEntry

ipxPRmtEntry 1.3.6.1.4.1.327.1.1.4.2.6.1
A list of information for an IPX dynamic route.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpxPRmtEntry  

ipxPRmtIndex 1.3.6.1.4.1.327.1.1.4.2.6.1.1
The route path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of prmtIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxPRmtNetNumber 1.3.6.1.4.1.327.1.1.4.2.6.1.2
The network address of the network that is attached to the path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(4)  

ipxPRmtNripUpdate 1.3.6.1.4.1.327.1.1.4.2.6.1.3
The method of sending NetWare RIP packets and updating routing database for this path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), trigger-update(2), periodic-update(3)  

ipxPRmtType 1.3.6.1.4.1.327.1.1.4.2.6.1.4
Indication of validity of this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

ipxRtUpdateTime 1.3.6.1.4.1.327.1.1.4.2.7
The time interval (in seconds) at which the routing information is being updated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipxRtEnabled 1.3.6.1.4.1.327.1.1.4.2.8
IPX router function enable/disable flag.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxRtRipEnabled 1.3.6.1.4.1.327.1.1.4.2.9
IPX RIP protocol enable/disable flag.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ipxRtResetAllCounters 1.3.6.1.4.1.327.1.1.4.2.11
Writing any value to this variable will reset all port-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipxRtInPackets 1.3.6.1.4.1.327.1.1.4.2.12
IPX packets received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipxRtOutPackets 1.3.6.1.4.1.327.1.1.4.2.13
IPX packets transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipxRtRipNumber 1.3.6.1.4.1.327.1.1.4.2.14
The number of RIP entries on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxRtRipTable 1.3.6.1.4.1.327.1.1.4.2.15
This table contains IPX RIP information. Each entry corresponds to a route description.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpxRtRipEntry

ipxRtRipEntry 1.3.6.1.4.1.327.1.1.4.2.15.1
A list of information for an IPX RIP entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpxRtRipEntry  

ipxRtRipDestNetNumber 1.3.6.1.4.1.327.1.1.4.2.15.1.1
The destination network's IPX network address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

ipxRtRipPathType 1.3.6.1.4.1.327.1.1.4.2.15.1.2
The variable indicates which route path table (local or remote) this route uses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), remote(2), proxy(3)  

ipxRtRipPathIdx 1.3.6.1.4.1.327.1.1.4.2.15.1.3
The route path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of plocalIndex or prmtIndex depending on path type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxRtRipNextHostAddress 1.3.6.1.4.1.327.1.1.4.2.15.1.4
The host address of next IPX router in this route.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

ipxRtRipHopCount 1.3.6.1.4.1.327.1.1.4.2.15.1.5
Number of hop needed to get to the destination network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxRtRipTicks 1.3.6.1.4.1.327.1.1.4.2.15.1.6
Number of ticks needed to get to the destination network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxRtRipRouteType 1.3.6.1.4.1.327.1.1.4.2.15.1.7
Indication of how the route is entered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER permanent(1), dynamic(2), static(3)  

ipxRtSapNumber 1.3.6.1.4.1.327.1.1.4.2.16
The number of SAP entries on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxRtSapTable 1.3.6.1.4.1.327.1.1.4.2.17
This table contains IPX SAP information. Each entry corresponds to a route description.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpxRtSapEntry

ipxRtSapEntry 1.3.6.1.4.1.327.1.1.4.2.17.1
A list of information for an IPX SAP entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpxRtSapEntry  

ipxRtSapIndex 1.3.6.1.4.1.327.1.1.4.2.17.1.1
A sequentially assigned index value for each entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxRtSapServiceName 1.3.6.1.4.1.327.1.1.4.2.17.1.2
The name of the service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(48)  

ipxRtSapServiceType 1.3.6.1.4.1.327.1.1.4.2.17.1.3
The variable indicates which type of service this is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipxRtSapServerNetNumber 1.3.6.1.4.1.327.1.1.4.2.17.1.4
The network address of next IPX router in this route.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

ipxRtSapServerHostAddress 1.3.6.1.4.1.327.1.1.4.2.17.1.5
The host address of next IPX router in this route.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

ipxSpoofingTime 1.3.6.1.4.1.327.1.1.4.2.18
The time which centrum remote server acts as proxy
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ipxRtDoNBPropagation 1.3.6.1.4.1.327.1.1.4.2.19
The variable indicates to flood the NETBIOS IPX propagation packets (type 20) to LAN and remote router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

brgFilterNumber 1.3.6.1.4.1.327.1.1.5.1
The number of bridge filters on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgFilterTable 1.3.6.1.4.1.327.1.1.5.2
This table contains bridge filter information. Each entry corresponds to a filter description. Each filter description can consist of up to four conditions. When a incoming packet matches all the conditions, the packet is filtered.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BrgFilterEntry

brgFilterEntry 1.3.6.1.4.1.327.1.1.5.2.1
A list of information for a bridge filter.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BrgFilterEntry  

brgFilterIndex 1.3.6.1.4.1.327.1.1.5.2.1.1
A sequentally assigned index value for each entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgFilterName 1.3.6.1.4.1.327.1.1.5.2.1.2
A unique user-recognizable name for each remote bridge filter defined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

brgFilterType 1.3.6.1.4.1.327.1.1.5.2.1.3
The indicates whether this filter is defined or not.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

brgFilterMask1Offset 1.3.6.1.4.1.327.1.1.5.2.1.4
The byte offset of the first mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

brgFilterMask1Value 1.3.6.1.4.1.327.1.1.5.2.1.5
The value of the first mask of this filter. This can be a byte, word or long value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgFilterMask1Type 1.3.6.1.4.1.327.1.1.5.2.1.6
The type of the 1st mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), equal(2), or(3), and(4), not(5)  

brgFilterMask1Size 1.3.6.1.4.1.327.1.1.5.2.1.7
The size (number of bytes covered by this mask) of the 1st mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER byte(1), half-word(2), word(3)  

brgFilterMask2Offset 1.3.6.1.4.1.327.1.1.5.2.1.8
The byte offset of the 2nd mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

brgFilterMask2Value 1.3.6.1.4.1.327.1.1.5.2.1.9
The value of the 2nd mask of this filter. This can be a byte, word or long value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgFilterMask2Type 1.3.6.1.4.1.327.1.1.5.2.1.10
The type of the 2nd mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), equal(2), or(3), and(4), not(5)  

brgFilterMask2Size 1.3.6.1.4.1.327.1.1.5.2.1.11
The size (number of bytes covered by this mask) of the 2nd mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER byte(1), half-word(2), word(3)  

brgFilterMask3Offset 1.3.6.1.4.1.327.1.1.5.2.1.12
The byte offset of the 3rd mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

brgFilterMask3Value 1.3.6.1.4.1.327.1.1.5.2.1.13
The value of the 3rd mask of this filter. This can be a byte, word or long value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgFilterMask3Type 1.3.6.1.4.1.327.1.1.5.2.1.14
The type of the 3rd mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), equal(2), or(3), and(4), not(5)  

brgFilterMask3Size 1.3.6.1.4.1.327.1.1.5.2.1.15
The size (number of bytes covered by this mask) of the 3rd mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER byte(1), half-word(2), word(3)  

brgFilterMask4Offset 1.3.6.1.4.1.327.1.1.5.2.1.16
The byte offset of the 4th mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

brgFilterMask4Value 1.3.6.1.4.1.327.1.1.5.2.1.17
The value of the 4th mask of this filter. This can be a byte, word or long value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgFilterMask4Type 1.3.6.1.4.1.327.1.1.5.2.1.18
The type of the 4th mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), equal(2), or(3), and(4), not(5)  

brgFilterMask4Size 1.3.6.1.4.1.327.1.1.5.2.1.19
The size (number of bytes covered by this mask) of the 4th mask of this filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER byte(1), half-word(2), word(3)  

brgFilterSkipRii 1.3.6.1.4.1.327.1.1.5.2.1.20
Specifying if source route field should be skipped for fitler offset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

brgLoggerNumber 1.3.6.1.4.1.327.1.1.5.3
The number of bridge logger on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgLoggerTable 1.3.6.1.4.1.327.1.1.5.4
This table contains bridge logger information. Each entry corresponds to a logging description. Each logging description can consist of up to four conditions. When a incoming packet matches all the conditions, the event is logged.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BrgLoggerEntry

brgLoggerEntry 1.3.6.1.4.1.327.1.1.5.4.1
A description of bridge logger.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BrgLoggerEntry  

brgLoggerIndex 1.3.6.1.4.1.327.1.1.5.4.1.1
A sequentally assigned index value for each entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgLoggerName 1.3.6.1.4.1.327.1.1.5.4.1.2
A unique user-recognizable name for each remote bridge logger defined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

brgLoggerType 1.3.6.1.4.1.327.1.1.5.4.1.3
The validity of this logger entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

brgLoggerMask1Offset 1.3.6.1.4.1.327.1.1.5.4.1.4
The byte offset of the 4th mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

brgLoggerMask1Value 1.3.6.1.4.1.327.1.1.5.4.1.5
The value of the 4th mask of this logger. This can be a byte, word or long value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgLoggerMask1Type 1.3.6.1.4.1.327.1.1.5.4.1.6
The type of the 4th mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), equal(2), or(3), and(4), not(5)  

brgLoggerMask1Size 1.3.6.1.4.1.327.1.1.5.4.1.7
The size (number of bytes covered by this mask) of the 1st mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER byte(1), half-word(2), word(3)  

brgLoggerMask2Offset 1.3.6.1.4.1.327.1.1.5.4.1.8
The byte offset of the 4th mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

brgLoggerMask2Value 1.3.6.1.4.1.327.1.1.5.4.1.9
The value of the 4th mask of this logger. This can be a byte, word or long value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgLoggerMask2Type 1.3.6.1.4.1.327.1.1.5.4.1.10
The type of the 4th mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), equal(2), or(3), and(4), not(5)  

brgLoggerMask2Size 1.3.6.1.4.1.327.1.1.5.4.1.11
The size (number of bytes covered by this mask) of the 2nd mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER byte(1), half-word(2), word(3)  

brgLoggerMask3Offset 1.3.6.1.4.1.327.1.1.5.4.1.12
The byte offset of the 4th mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

brgLoggerMask3Value 1.3.6.1.4.1.327.1.1.5.4.1.13
The value of the 4th mask of this logger. This can be a byte, word or long value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgLoggerMask3Type 1.3.6.1.4.1.327.1.1.5.4.1.14
The type of the 4th mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), equal(2), or(3), and(4), not(5)  

brgLoggerMask3Size 1.3.6.1.4.1.327.1.1.5.4.1.15
The size (number of bytes covered by this mask) of the 3rd mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER byte(1), half-word(2), word(3)  

brgLoggerMask4Offset 1.3.6.1.4.1.327.1.1.5.4.1.16
The byte offset of the 4th mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

brgLoggerMask4Value 1.3.6.1.4.1.327.1.1.5.4.1.17
The value of the 4th mask of this logger. This can be a byte, word or long value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgLoggerMask4Type 1.3.6.1.4.1.327.1.1.5.4.1.18
The type of the 4th mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), equal(2), or(3), and(4), not(5)  

brgLoggerMask4Size 1.3.6.1.4.1.327.1.1.5.4.1.19
The size (number of bytes covered by this mask) of the 4th mask of this logger.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER byte(1), half-word(2), word(3)  

brgLoggerSkipRii 1.3.6.1.4.1.327.1.1.5.4.1.20
Specifying if source route field should be skipped for logger offset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

brgPLocalNumber 1.3.6.1.4.1.327.1.1.5.5
The number of local bridge path on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgPLocalTable 1.3.6.1.4.1.327.1.1.5.6
This table contains bridge path (equivalent to port in 802.1d specification) information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BrgPLocalEntry

brgPLocalEntry 1.3.6.1.4.1.327.1.1.5.6.1
A description of bridge path entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BrgPLocalEntry  

brgPLocalIndex 1.3.6.1.4.1.327.1.1.5.6.1.1
The path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same path as identified by the same value of plocalIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgPLocalEnabled 1.3.6.1.4.1.327.1.1.5.6.1.2
Enable this path as one of the bridge port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

brgStpPLocalPriority 1.3.6.1.4.1.327.1.1.5.6.1.3
The value of the priority field which is contained in the first octet of the Port ID. The other octet of the Port ID is given by the value of brgPLocalIndex.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgStpPLocalCost 1.3.6.1.4.1.327.1.1.5.6.1.4
The contribution of this port to the path cost of paths towards the spanning tree root which include this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgStpPLocalDesigRoot 1.3.6.1.4.1.327.1.1.5.6.1.5
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

brgStpPLocalDesigCost 1.3.6.1.4.1.327.1.1.5.6.1.6
The path cost of the Designated Port of the segment connected to the port. This value is compared to the Root Path Cost field in received bridge PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgStpPLocalDesigBridge 1.3.6.1.4.1.327.1.1.5.6.1.7
The Bridge ID of the bridge which this port considers to be the Designated Bridge for this port's segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

brgStpPLocalDesigPath 1.3.6.1.4.1.327.1.1.5.6.1.8
The Port ID of the port on the Designated Bridge for this port's segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgStpPLocalPathState 1.3.6.1.4.1.327.1.1.5.6.1.9
The Spanning Tree state of the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER listening(1), blocking(2), learning(3), forwarding(4), disabled(255)  

brgPRmtNumber 1.3.6.1.4.1.327.1.1.5.7
The number of remote bridge path on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgPRmtTable 1.3.6.1.4.1.327.1.1.5.8
This table contains bridge path (equivalent to port in 802.1d specification) information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BrgPRmtEntry

brgPRmtEntry 1.3.6.1.4.1.327.1.1.5.8.1
A description of bridge path entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BrgPRmtEntry  

brgPRmtIndex 1.3.6.1.4.1.327.1.1.5.8.1.1
The path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same path as identified by the same value of prmtIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgPRmtEnabled 1.3.6.1.4.1.327.1.1.5.8.1.2
Enable this path as one of the bridge port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

brgStpPRmtPriority 1.3.6.1.4.1.327.1.1.5.8.1.3
The value of the priority field which is contained in the first octet of the Port ID. The other octet of the Port ID is given by the value of brgPRmtIndex.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgStpPRmtCost 1.3.6.1.4.1.327.1.1.5.8.1.4
The contribution of this port to the path cost of paths towards the spanning tree root which include this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgStpPRmtDesigRoot 1.3.6.1.4.1.327.1.1.5.8.1.5
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

brgStpPRmtDesigCost 1.3.6.1.4.1.327.1.1.5.8.1.6
The path cost of the Designated Port of the segment connected to the port. This value is compared to the Poot Path Cost field in received bridge PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgStpPRmtDesigBridge 1.3.6.1.4.1.327.1.1.5.8.1.7
The Bridge ID of the bridge which this port considers to be the Designated Bridge for this port's segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

brgStpPRmtDesigPath 1.3.6.1.4.1.327.1.1.5.8.1.8
The Port ID of the port on the Designated Bridge for this port's segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgStpPRmtPathState 1.3.6.1.4.1.327.1.1.5.8.1.9
The Spanning Tree state of the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER listening(1), blocking(2), learning(3), forwarding(4), disabled(255)  

brgMisc 1.3.6.1.4.1.327.1.1.5.9
OBJECT IDENTIFIER    

brgSpanningTreeProtocol 1.3.6.1.4.1.327.1.1.5.9.1
This flag controls whether Spanning Tree protocol feature be enabled in this node.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enable(2)  

brgResetAllCounters 1.3.6.1.4.1.327.1.1.5.9.2
Writing any value to this variable will reset all brg-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgAutoFtrEnabled 1.3.6.1.4.1.327.1.1.5.9.3
This flag controls whether auto filter feature is enabled in this node.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enable(2)  

brgPRPASmartFiltering 1.3.6.1.4.1.327.1.1.5.9.4
This enables/disables AccessBuilder's Smart Filtering feature.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

brgPRPAFilterAction 1.3.6.1.4.1.327.1.1.5.9.5
The action to be taken for all remote access path's filters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER discard(1), forward(2)  

brgPRPAFilterMap 1.3.6.1.4.1.327.1.1.5.9.6
This is a 16 bit bitmap corresponds to the bridge filter table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

brgPRPALoggerMap 1.3.6.1.4.1.327.1.1.5.9.7
This is a 16 bit bitmap corresponds to the bridge logger table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

brgMacHdrComp 1.3.6.1.4.1.327.1.1.5.9.8
Turn on/off bridge MAC header compression.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

brgLearnedTable 1.3.6.1.4.1.327.1.1.5.10
Spanning tree bridge port table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BrgLearnedEntry

brgLearnedEntry 1.3.6.1.4.1.327.1.1.5.10.1
A list of information for a learned address entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BrgLearnedEntry  

brgLearnedAddress 1.3.6.1.4.1.327.1.1.5.10.1.1
A MAC address for the bridge has learned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

brgLearnedPathType 1.3.6.1.4.1.327.1.1.5.10.1.2
The variable indicates from which path table (local or remote) this address is leaned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local(1), remote(2), permanent(3)  

brgLearnedPathIdx 1.3.6.1.4.1.327.1.1.5.10.1.3
The path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of plocalIndex or prmtIndex depending on path type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brgLearnedAge 1.3.6.1.4.1.327.1.1.5.10.1.4
The relative newness of the learned address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER young(1), middle(2), old(3), permanent(4)  

brgTokenRing 1.3.6.1.4.1.327.1.1.5.11
OBJECT IDENTIFIER    

brgLocalRingNumber 1.3.6.1.4.1.327.1.1.5.11.1
The ring number on LAN side interface of the AccessBuilder.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgProxyRingNumber 1.3.6.1.4.1.327.1.1.5.11.2
The ring number on WAN side interface of the AccessBuilder.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brgBridgeNumber 1.3.6.1.4.1.327.1.1.5.11.3
The bridge number assigned to AccessBuilder.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminUserNumber 1.3.6.1.4.1.327.1.1.6.1
The number of users registered on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminUserTable 1.3.6.1.4.1.327.1.1.6.2
User table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdminUserEntry

adminUserEntry 1.3.6.1.4.1.327.1.1.6.2.1
A list of information for a user.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdminUserEntry  

adminUserIndex 1.3.6.1.4.1.327.1.1.6.2.1.1
A sequentally assigned index value for each entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminUserName 1.3.6.1.4.1.327.1.1.6.2.1.2
The user login name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..10)  

adminUserType 1.3.6.1.4.1.327.1.1.6.2.1.3
This value controls whether the user be given superuser, administrator or regular user priviledge while in User Interface session.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), user(2), admin(3), su(4)  

adminUserPassword 1.3.6.1.4.1.327.1.1.6.2.1.4
The user login password.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

adminUserCallBackPhone 1.3.6.1.4.1.327.1.1.6.2.1.5
This string controls whether the system should disconnect the line and call back to the user for security reason. If this is a NULL string, the system does not call back. Otherwise, the system calls back with number given by this string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..15)  

adminEncryptUserPassword 1.3.6.1.4.1.327.1.1.6.2.1.6
The encrypted user password is for configurator to change user password by a authentication algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

adminEncryptCallBackPhone 1.3.6.1.4.1.327.1.1.6.2.1.7
The encrypted call back phone no. is for configurator to change user password by a authentication algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..24)  

adminCommNumber 1.3.6.1.4.1.327.1.1.6.3
The number of SNMP communities defined on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminCommTable 1.3.6.1.4.1.327.1.1.6.4
SNMP community table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdminCommEntry

adminCommEntry 1.3.6.1.4.1.327.1.1.6.4.1
A list of information for a SNMP community.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdminCommEntry  

adminCommIndex 1.3.6.1.4.1.327.1.1.6.4.1.1
A sequentally assigned index value for each entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminCommName 1.3.6.1.4.1.327.1.1.6.4.1.2
The community name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..10)  

adminCommType 1.3.6.1.4.1.327.1.1.6.4.1.3
The community's access type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), readOnly(2), readWrite(3)  

adminCommMgrIpAddress 1.3.6.1.4.1.327.1.1.6.4.1.4
The community network manager's IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

adminCommMgrIpxNetNumber 1.3.6.1.4.1.327.1.1.6.4.1.5
The community network manager's IPX network ID.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(4)  

adminCommMgrMacAddress 1.3.6.1.4.1.327.1.1.6.4.1.6
The community network manager's MAC address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(6)  

adminScriptNumber 1.3.6.1.4.1.327.1.1.6.5
The number of dialing scripts on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminScriptTable 1.3.6.1.4.1.327.1.1.6.6
Dialing script table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdminScriptEntry

adminScriptEntry 1.3.6.1.4.1.327.1.1.6.6.1
A list of dialing script information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdminScriptEntry  

adminScriptIndex 1.3.6.1.4.1.327.1.1.6.6.1.1
A sequentally assigned index value for each entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminScriptName 1.3.6.1.4.1.327.1.1.6.6.1.2
The name of the script.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

adminScriptType 1.3.6.1.4.1.327.1.1.6.6.1.3
The script's type. A built-in script's type can not be changed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), built-in(2), user-defined(3)  

adminScript 1.3.6.1.4.1.327.1.1.6.6.1.4
The connection control string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..527)  

adminRpaLogNumber 1.3.6.1.4.1.327.1.1.6.7
The number of remote PC access session log entries in this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminRpaLogTable 1.3.6.1.4.1.327.1.1.6.8
Remote PC access session log table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdminRpaLogEntry

adminRpaLogEntry 1.3.6.1.4.1.327.1.1.6.8.1
A list of logged remote PC access session information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdminRpaLogEntry  

adminRpaLogIndex 1.3.6.1.4.1.327.1.1.6.8.1.1
A sequentally assigned index value for each entry. Index 32 always points to the most-recently completed remote PC access session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminRpaLogUserName 1.3.6.1.4.1.327.1.1.6.8.1.2
The name of the logged-in user.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

adminRpaLogTime 1.3.6.1.4.1.327.1.1.6.8.1.3
The start time (in HH:MM:SS) of this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

adminRpaLogDuration 1.3.6.1.4.1.327.1.1.6.8.1.4
The elapsed time (in HH:MM:SS) of this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

adminRpaLogAttempts 1.3.6.1.4.1.327.1.1.6.8.1.5
Number of unsuccessful login attempts in this authentication process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adminRpaLogInPackets 1.3.6.1.4.1.327.1.1.6.8.1.6
Number of correctly received packets in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adminRpaLogOutPackets 1.3.6.1.4.1.327.1.1.6.8.1.7
Number of correctly transmitted packets in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adminRpaLogInBytes 1.3.6.1.4.1.327.1.1.6.8.1.8
Number of correctly received bytes in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adminRpaLogOutBytes 1.3.6.1.4.1.327.1.1.6.8.1.9
Number of correctly transmitted bytes in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adminRpaLogParityErrors 1.3.6.1.4.1.327.1.1.6.8.1.10
Number of characters received with parity error in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adminRpaLogFrameErrors 1.3.6.1.4.1.327.1.1.6.8.1.11
Number of characters received with framing error in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adminRpaLogOverrunErrors 1.3.6.1.4.1.327.1.1.6.8.1.12
Number of receive overrun errors in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adminRpaLogCksumErrors 1.3.6.1.4.1.327.1.1.6.8.1.13
Number of receive checksum errors in this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adminRpaLogDate 1.3.6.1.4.1.327.1.1.6.8.1.14
The start date (in MM/DD/YY) of this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

adminRpaLogPortName 1.3.6.1.4.1.327.1.1.6.8.1.15
The binding portname of this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..40)  

adminRpaLogPathName 1.3.6.1.4.1.327.1.1.6.8.1.16
The binding pathname of this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..12)  

adminMisc 1.3.6.1.4.1.327.1.1.6.9
OBJECT IDENTIFIER    

adminSysDescr 1.3.6.1.4.1.327.1.1.6.9.1
Same as sysDescr in MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

adminNodeName 1.3.6.1.4.1.327.1.1.6.9.2
The login ID that is transmitted by this node to a remote router at connection establishing time. If the string is not what the remote router expects, the connection will be rejected.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..10)  

adminNodePassword 1.3.6.1.4.1.327.1.1.6.9.3
The password that is transmitted by this node to a remote router after login ID at connection establishing time. If the string is not what the remote router expects, the connection will be rejected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

adminDate 1.3.6.1.4.1.327.1.1.6.9.4
Current date in mm/dd/yy format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

adminTime 1.3.6.1.4.1.327.1.1.6.9.5
Current time in hh:mm:ss format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

adminGreeting 1.3.6.1.4.1.327.1.1.6.9.6
A user-defined text that is displayed when a user logs into User Interface process.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

adminPrompt 1.3.6.1.4.1.327.1.1.6.9.7
An user-defined prompt string for this node's User Interface process. Note: This one is obsoleted after version 3.1 or later
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..10)  

adminSNMPGetFrom 1.3.6.1.4.1.327.1.1.6.9.8
The value controls the type value returned to an SNMP GET command. Setting this to '1' requests that the current operational value of this variable is returned. Setting it to '2' requests that the configured value (which will take effect after a re-boot) is returned. The default is '1'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER current-value(1), config-value(2)  

adminDoIntegrity 1.3.6.1.4.1.327.1.1.6.9.9
A write to this variable (value don't care) cause an integrity check on all the configuration parameters. The result is given through a GET of this variable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER integrity-check-OK(1), integrity-check-failed(2)  

adminDoFileload 1.3.6.1.4.1.327.1.1.6.9.10
A write to this variable (value don't care) cause a fileload (upload or download depending on LoadFileName) operation to start. The result is given through a GET of this variable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER fileload-OK(1), fileload-failed(2)  

adminLoadfileName 1.3.6.1.4.1.327.1.1.6.9.11
The name of the file upon which the file-load operation is to be operated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..12)  

adminLastTrap 1.3.6.1.4.1.327.1.1.6.9.13
The last trap message contents.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

adminResetAllUserCounters 1.3.6.1.4.1.327.1.1.6.9.14
Writing any value to this variable will reset all User-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminEraseConfig 1.3.6.1.4.1.327.1.1.6.9.15
Erase all configuration data in EEPROM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminUIMsgLevel 1.3.6.1.4.1.327.1.1.6.9.16
This variable controls type of system messages to be displayed on system console. Messages of priority equals or higher than the specified level are displayed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER panic-level(1), error-level(2), warning-level(3), status-level(4)  

adminSNMPMsgLevel 1.3.6.1.4.1.327.1.1.6.9.17
This variable controls type of system messages to be sent to SNMP management stations. Messages of priority equals or higher than the specified level are sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), error-level(2), warning-level(3), status-level(4)  

adminLoginOption 1.3.6.1.4.1.327.1.1.6.9.18
This variable enable the login sequence on async ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), nologin(2), nopassword(3)  

adminReboot 1.3.6.1.4.1.327.1.1.6.9.19
Reboot the AccessBuilder server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminMajorVersion 1.3.6.1.4.1.327.1.1.6.9.20
AccessBuilder software Major version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminMinorVersion 1.3.6.1.4.1.327.1.1.6.9.21
AccessBuilder software Minor version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminMIBVersion 1.3.6.1.4.1.327.1.1.6.9.22
This MIB version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminTimeZone 1.3.6.1.4.1.327.1.1.6.9.23
Time difference between local time zone and Greenwich time (in minutes).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..4)  

adminSecurityServerType 1.3.6.1.4.1.327.1.1.6.9.24
Enables authentication through security helpers instead of local user database.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER internal(1), ab-nameserver(2), dce-server(3), ace-server(4), nw-bindery(5), nw-nds(6), generic(7), nt(8)  

adminSecPassword 1.3.6.1.4.1.327.1.1.6.9.25
The password is used to set up a session with security helpers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

adminScrtyClntIpAddr 1.3.6.1.4.1.327.1.1.6.9.26
The primary security helper's IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

adminSecondScrtyClntIpAddr 1.3.6.1.4.1.327.1.1.6.9.27
The secondary security helper's IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

adminUdpPort 1.3.6.1.4.1.327.1.1.6.9.28
This is the UDP port for the security helper protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminTelnetAdminPort 1.3.6.1.4.1.327.1.1.6.9.29
This is the telnet administration port for dialout function.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminTelnetDialOutAuth 1.3.6.1.4.1.327.1.1.6.9.30
Enables authentication for dialout function.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

adminDialOutEnabled 1.3.6.1.4.1.327.1.1.6.9.31
Enables dialout function.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

adminEncryptNodePassword 1.3.6.1.4.1.327.1.1.6.9.32
The encrypted node password is for configurator to change node password by a authentication algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

adminEncryptSecurityServerType 1.3.6.1.4.1.327.1.1.6.9.33
The encrypted security server type is for configurator to change security server type by a authentication algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

adminEncryptSecPassword 1.3.6.1.4.1.327.1.1.6.9.34
The encrypted security password is for configurator to change security password by a authentication algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

adminEncryptScrtyClntIpAddr 1.3.6.1.4.1.327.1.1.6.9.35
The encrypted helper IP address is for configurator to change helper IP address by a authentication algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

adminEncryptSecondScrtyClntIpAddr 1.3.6.1.4.1.327.1.1.6.9.36
The encrypted secondary helper IP address is for configurator to change secondary helper IP address by a authentication algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

adminEncryptUdpPort 1.3.6.1.4.1.327.1.1.6.9.37
The encrypted helper UDP port is for configurator to change helper UDP port by a authentication algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

adminEPromSize 1.3.6.1.4.1.327.1.1.6.9.38
This is the EProm size on the mother board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminNVRamSize 1.3.6.1.4.1.327.1.1.6.9.39
This is the Non-Volatile Ram (EEProm) size on the mother board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminFlashRomSize 1.3.6.1.4.1.327.1.1.6.9.40
This is the Flash Rom size on the mother board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminLocalDRamSize 1.3.6.1.4.1.327.1.1.6.9.41
This is the Local DRam size on the mother board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminSharedDRamSize 1.3.6.1.4.1.327.1.1.6.9.42
This is the Shared DRam size on the mother board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminHWRev 1.3.6.1.4.1.327.1.1.6.9.43
This is the hardware revision on mother board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminEncryptSuperUserPassword 1.3.6.1.4.1.327.1.1.6.9.44
The encrypted superuser password is for configurator to get the superuser password.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

adminNewGreeting 1.3.6.1.4.1.327.1.1.6.9.45
A user-defined text that is displayed when a user logs into User Interface process.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

adminTFTPServerIpAddr 1.3.6.1.4.1.327.1.1.6.9.46
The TFTP server's IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

adminSaveConfig 1.3.6.1.4.1.327.1.1.6.9.47
A write to this variable (value don't care) cause a save configuration operation to start. The result is given through a GET of this variable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER save-OK(1), save-failed(2)  

adminMaintenanceVersion 1.3.6.1.4.1.327.1.1.6.9.48
AccessBuilder software Maintenance version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminCheckConsoleModem 1.3.6.1.4.1.327.1.1.6.9.49
Check the status of console modem.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminConsoleImageDownload 1.3.6.1.4.1.327.1.1.6.9.50
Download image by console port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminConsoleConfigUpload 1.3.6.1.4.1.327.1.1.6.9.51
Upload configuration by console port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminConsoleConfigDownload 1.3.6.1.4.1.327.1.1.6.9.52
Download configuration by console port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminRasIdleTime 1.3.6.1.4.1.327.1.1.6.9.53
The idle time to start spoofing for ras port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminRouterIdleTime 1.3.6.1.4.1.327.1.1.6.9.54
The idle time to start spoofing for router port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminRasSpoofTime 1.3.6.1.4.1.327.1.1.6.9.55
The time to spoof for ras port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminRouterSpoofTime 1.3.6.1.4.1.327.1.1.6.9.56
The time to spoof for router port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminLnkUtilHighThld 1.3.6.1.4.1.327.1.1.6.9.57
Link utilization high threshold.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminLnkUtilLowThld 1.3.6.1.4.1.327.1.1.6.9.58
Link utilization low threshold.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminCallerIdCheck 1.3.6.1.4.1.327.1.1.6.9.59
Indicate to check caller id or not.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

adminISDNRequiredBaudrate 1.3.6.1.4.1.327.1.1.6.9.60
For baudrate adaption of ISDN call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER br-56000(1), br-64000(2), auto(3)  

adminRouterCCPEnabled 1.3.6.1.4.1.327.1.1.6.9.61
Turn on/off CCP for remotepath.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

adminSuggestFlag 1.3.6.1.4.1.327.1.1.6.9.62
Turn on/off for ignoring some trivial error message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), on(2)  

adminEEVersionNo 1.3.6.1.4.1.327.1.1.6.9.63
The EE version number, format is Major, Miror, Maintence and Patch
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

adminMdSetupNumber 1.3.6.1.4.1.327.1.1.6.10
The number of dialing Modem Setups on this system; this table serves as a template to create 'real' modem script.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminMdSetupTable 1.3.6.1.4.1.327.1.1.6.11
Dialing Modem Setup table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdminMdSetupEntry

adminMdSetupEntry 1.3.6.1.4.1.327.1.1.6.11.1
A list of dialing Modem Setup information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdminMdSetupEntry  

adminMdSetupIndex 1.3.6.1.4.1.327.1.1.6.11.1.1
A sequentally assigned index value for each entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminMdSetupType 1.3.6.1.4.1.327.1.1.6.11.1.2
The Modem Setup's type. A built-in Modem Setup's type can not be changed. This type has to be set to user-defined before set the following entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), built-in(2), user-defined(3)  

adminMdSetupName 1.3.6.1.4.1.327.1.1.6.11.1.3
The name of the Modem Setup. Once congifured, this name can not be changed
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

adminMdSetupATCmd 1.3.6.1.4.1.327.1.1.6.11.1.4
The AT config command string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..79)  

adminMdSetupARAP1-0ATCmd 1.3.6.1.4.1.327.1.1.6.11.1.5
The AT config command string for ARAP1.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..79)  

adminMdSetupIncomingCall 1.3.6.1.4.1.327.1.1.6.11.1.6
The In Coming call Indication: ri signal or 'ring' text
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ri(1), ring(2)  

adminMdSetupConnIndication 1.3.6.1.4.1.327.1.1.6.11.1.7
The In Connect Indication: DCD signal or 'connect' text
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER connect(1), dcd(2)  

adminMdSetupCallTimeOut 1.3.6.1.4.1.327.1.1.6.11.1.8
The Call Time Out interval: 0 - 255 sec
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminMdSetupCallDelay 1.3.6.1.4.1.327.1.1.6.11.1.9
The Call Setup Delay interval: 0 - 120000 msec
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adminCallerIDNumber 1.3.6.1.4.1.327.1.1.6.12
Caller Id Number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminCallerIDTable 1.3.6.1.4.1.327.1.1.6.13
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdminCallerIDEntry

adminCallerIDEntry 1.3.6.1.4.1.327.1.1.6.13.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdminCallerIDEntry  

adminCallerIDIndex 1.3.6.1.4.1.327.1.1.6.13.1.1
A sequentally assigned index value for each entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adminCallerIDName 1.3.6.1.4.1.327.1.1.6.13.1.2
Tok_String
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

adminCallerIDType 1.3.6.1.4.1.327.1.1.6.13.1.3
Tok_String
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

adminCallerIDComment 1.3.6.1.4.1.327.1.1.6.13.1.4
Tok_String
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..10)  

atRpa 1.3.6.1.4.1.327.1.1.7.1
OBJECT IDENTIFIER    

atRt 1.3.6.1.4.1.327.1.1.7.2
OBJECT IDENTIFIER    

atRpaNumber 1.3.6.1.4.1.327.1.1.7.1.1
The number of AppleTalk (AT) remote PC paths on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atRpaTable 1.3.6.1.4.1.327.1.1.7.1.2
Remote PC access path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtRpaEntry

atRpaEntry 1.3.6.1.4.1.327.1.1.7.1.2.1
A path to a remote PC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AtRpaEntry  

atRpaIndex 1.3.6.1.4.1.327.1.1.7.1.2.1.1
The RPA path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same RPA path as identified by the same value of prpaIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atRpaNetworkAddress 1.3.6.1.4.1.327.1.1.7.1.2.1.2
The current or last logged-in remote PC's AT address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(3)  

atRpaState 1.3.6.1.4.1.327.1.1.7.1.2.1.3
The state of ARA connection
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atRpaDialInZone 1.3.6.1.4.1.327.1.1.7.1.3
The name of specific zone for the remote Mac Users; Note: reboot to take effect
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

atRpaMaxConnTime 1.3.6.1.4.1.327.1.1.7.1.4
The time interval of a seesion is allowed after login, in minutes; 1 to 65,535; 0 = no limit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

atRpaNoNbpMulticast 1.3.6.1.4.1.327.1.1.7.1.5
Whether to discard NBP multicast packets
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

atPLocalNumber 1.3.6.1.4.1.327.1.1.7.2.1
The number of AT dynamic routes on this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atPLocalTable 1.3.6.1.4.1.327.1.1.7.2.2
AT dynamic route table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtPLocalEntry

atPLocalEntry 1.3.6.1.4.1.327.1.1.7.2.2.1
A list of information for a AT dynamic route.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AtPLocalEntry  

atPLocalIndex 1.3.6.1.4.1.327.1.1.7.2.2.1.1
The route path on which the entry's equivalence is effective. The path identified by a particular value of this index is the same route path as identified by the same value of plocalIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atPLocalNetAddress 1.3.6.1.4.1.327.1.1.7.2.2.1.2
The current or last logged-in remote PC's AT address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(3)  

atPLocalNetStart 1.3.6.1.4.1.327.1.1.7.2.2.1.3
The current or last logged-in remote PC's AT address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atPLocalNetEnd 1.3.6.1.4.1.327.1.1.7.2.2.1.4
The current or last logged-in remote PC's AT address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atPLocalDefaultRouter 1.3.6.1.4.1.327.1.1.7.2.2.1.5
The current or last logged-in remote PC's AT address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(3)  

atPLocalLocalZone 1.3.6.1.4.1.327.1.1.7.2.2.1.6
The current or last logged-in remote PC's AT address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

atAarpTable 1.3.6.1.4.1.327.1.1.7.2.3
The AT Address Translation table used for mapping from AT addresses to physical addresses.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtAarpEntry

atAarpEntry 1.3.6.1.4.1.327.1.1.7.2.3.1
Each entry contains one AT Address to `physical' address equivalence.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AtAarpEntry  

atAarpIfIndex 1.3.6.1.4.1.327.1.1.7.2.3.1.1
The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atAarpPhysAddress 1.3.6.1.4.1.327.1.1.7.2.3.1.2
The media-dependent `physical' address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

atAarpNetAddress 1.3.6.1.4.1.327.1.1.7.2.3.1.3
The AtAddress corresponding to the media- dependent `physical' address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(3)  

atBestRouterCacheTable 1.3.6.1.4.1.327.1.1.7.2.4
The table for efficiently forwarding AT packets to remote networks.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtBestRouterCacheEntry

atBestRouterCacheEntry 1.3.6.1.4.1.327.1.1.7.2.4.1
Each entry contains one AT Address and router physical address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AtBestRouterCacheEntry  

atBestRouterCacheIfIndex 1.3.6.1.4.1.327.1.1.7.2.4.1.1
The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atBestRouterCachePhysAddress 1.3.6.1.4.1.327.1.1.7.2.4.1.2
The host address of the next router a packet should go through to reach the specified AppleTalk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

atBestRouterCacheNetAddress 1.3.6.1.4.1.327.1.1.7.2.4.1.3
The At Address for recently learned routers on the same network segment as the AccessBuilder.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(3)  

atRtProtocolEnabled 1.3.6.1.4.1.327.1.1.7.2.5
ARAP protocol enable/disable flag.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

atRtInPackets 1.3.6.1.4.1.327.1.1.7.2.6
AT packets received with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atRtOutPackets 1.3.6.1.4.1.327.1.1.7.2.7
AT packets transmitted with no error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atRtResetAllCounters 1.3.6.1.4.1.327.1.1.7.2.8
Writing any value to this variable will reset all port-related counters to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

atRtZoneFilterAction 1.3.6.1.4.1.327.1.1.7.2.9
This variable indicate the operation of zone filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER discard(1), forward(2)  

atZoneFilterTable 1.3.6.1.4.1.327.1.1.7.2.10
Zone Filter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtZoneFilterEntry

atZoneFilterEntry 1.3.6.1.4.1.327.1.1.7.2.10.1
A list of information for a zone filter.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AtZoneFilterEntry  

atZoneFilterIndex 1.3.6.1.4.1.327.1.1.7.2.10.1.1
A sequentally assigned index value for each entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atZoneFilterName 1.3.6.1.4.1.327.1.1.7.2.10.1.2
The zone filter name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

atZoneFilterType 1.3.6.1.4.1.327.1.1.7.2.10.1.3
This value controls whether the zone filter name is valid or invalid. It will be set valid while adding and set invalid while deleting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

userLogInTrap 16
This trap is sent after the user logged in the AccessBuilder.
TRAP-TYPE    

userLogOutTrap 17
This trap is sent after the user logged out the AccessBuilder.
TRAP-TYPE    

userSessionTimeOutTrap 18
This trap is sent after the user logged out due to idle time expired.
TRAP-TYPE