CTRON-REMOTE-ACCESS-MIB

File: CTRON-REMOTE-ACCESS-MIB.mib (141679 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212

Imported symbols

IpAddress Counter enterprises
DisplayString OBJECT-TYPE

Defined Types

Index  
INTEGER    

DLCI  
INTEGER    

CtRemPhysPortEntry  
SEQUENCE    
  ctRemConnectionIndex INTEGER
  ctRemPhysPortType INTEGER
  ctRemPhysPortSpecificMib OBJECT IDENTIFIER
  ctRemPhysPortProtMgrType INTEGER
  ctRemPhysPortProtMgrIfaceNum INTEGER
  ctRemPhysPortWanIfaceNum INTEGER
  ctRemPhysPortProtMgrMaxIfos INTEGER
  ctRemPhysPortProtMgrIfaceList DisplayString
  ctRemPhysAlarmTimeOut INTEGER
  ctRemPhysWpimType INTEGER

CtRemInterfaceEntry  
SEQUENCE    
  ctRemIntEntIfIndex INTEGER
  ctRemIntEntCompression INTEGER
  ctRemIntEntCompRatio DisplayString
  ctRemIntEntCompStatus INTEGER
  ctRemIntEntMTU INTEGER
  ctRemIntEntCongestion INTEGER
  ctRemIntEntMaxProfiles INTEGER
  ctRemIntEntTxIdleTimeout INTEGER
  ctRemIntEntRxIdleTimeout INTEGER
  ctRemIntEntCircuitName DisplayString
  ctRemIntEntEncryption INTEGER
  ctRemIntEntEncryptStatus INTEGER

CtRemPrimaryInterfaceEntry  
SEQUENCE    
  ctRemPriIntEntIfIndex INTEGER
  ctRemPriIntEntConnectRetryInterval INTEGER

CtRemBackupInterfaceEntry  
SEQUENCE    
  ctRemIntEntBackupIfIndex INTEGER
  ctRemIntEntBackupIfNum INTEGER
  ctRemIntEntBackupIfInUseCnt INTEGER
  ctRemIntEntBackupIfTimeToConnect INTEGER
  ctRemIntEntBackupIfTimeToDisconnect INTEGER
  ctRemIntEntBackupIfOverride INTEGER
  ctRemIntEntBackupConnectRetries INTEGER
  ctRemIntEntBackupConnectRetryInterval INTEGER

CtRemExtPhysPortEntry  
SEQUENCE    
  ctRemExtConnectionIndex INTEGER
  ctRemExtProtMgrIndex INTEGER
  ctRemExtPhysPortProtMgrType INTEGER
  ctRemExtPhysPortProtMgrEnable INTEGER
  ctRemExtPhysPortProtMgrIfaceNum INTEGER
  ctRemExtPhysPortProtMgrMaxIfos INTEGER
  ctRemExtPhysPortProtMgrIfaceList DisplayString
  ctRemExtPhysPortProtMgrChannelList DisplayString

CtDs1ExtensionsEntry  
SEQUENCE    
  ctDs1ExtensionsEntryIndex INTEGER
  ctDs1ExtensionsNumInterfaces INTEGER
  ctDs1ExtensionsToggleFracTable INTEGER
  ctDs1ExtensionsLineBuildOut INTEGER
  ctDs1ExtensionsCFADuration INTEGER
  ctDs1ExtensionsDIEnable INTEGER
  ctDs1ExtensionsTotalValidIntervals Counter
  wanDs1ExtensionsBertTestMode INTEGER
  wanDs1ExtensionsBertRun INTEGER
  wanDs1ExtensionsBertCurrentResults INTEGER
  wanDs1ExtensionsBertCumulativeResults INTEGER
  wanDs1ExtensionsBertPeakResults INTEGER
  wanDs1ExtensionsBertAverageResult INTEGER
  wanDs1ExtensionsBertTestPattern INTEGER
  wanDs1ExtensionsBertSamplePeriod INTEGER
  wanDs1ExtensionsBertNumPeriods Counter
  wanDs1ExtensionsBertTestTraps INTEGER
  wanDs1ExtensionsBertDataStatus INTEGER

CtDs1WanDriverEntry  
SEQUENCE    
  ctDs1WanDriverEntryIndex INTEGER
  ctDs1WanDriverChannelIndex INTEGER
  ctDs1WanDriverLineCode INTEGER
  ctDs1WanDriverCRCBits INTEGER

CtRs232ExtensionsEntry  
SEQUENCE    
  ctRs232ExtensionsEntryIndex INTEGER
  ctRs232ExtensionsCTSEnable INTEGER
  ctRs232ExtensionsDSREnable INTEGER
  ctRs232ExtensionsRTSEnable INTEGER
  ctRs232ExtensionsDTREnable INTEGER

FrDcpCircuitEntry  
SEQUENCE    
  frDcpCircuitIfIndex Index
  frDcpCircuitDlci DLCI
  frDcpCircuitEnable INTEGER
  frDcpCircuitStatus INTEGER
  frDcpCircuitRatio OCTET STRING

CtDDSConfigEntry  
SEQUENCE    
  ctDDSLineIndex INTEGER
  ctDDSIfIndex INTEGER
  ctDDSLineMode INTEGER
  ctDDSLineCoding INTEGER
  ctDDSLoopbackConfig INTEGER
  ctDDSLineStatus INTEGER
  ctDDSTxClockSource INTEGER
  ctDDSPortInSpeed INTEGER
  ctDDSPortOutSpeed INTEGER

CtPppCountersEntry  
SEQUENCE    
  ctPppCountersIfIndex INTEGER
  ctPppCountersMaxTerminate INTEGER
  ctPppCountersMaxConfigure INTEGER
  ctPppCountersMaxFailure INTEGER
  ctPppCountersRestartTimer INTEGER

CtPppLcpExtEntry  
SEQUENCE    
  ctPppLcpExtIfIndex INTEGER
  ctPppLcpExtAuthenticationProt INTEGER
  ctPppLcpExtQualityProt INTEGER
  ctPppLcpExtPFC INTEGER
  ctPppLcpExtACFC INTEGER
  ctPppLcpExtSelfDescribePadding INTEGER
  ctPppLcpExtCallback INTEGER
  ctPppLcpExtCompoundFrames INTEGER
  ctPppLcpExtMru INTEGER
  ctPppLcpExtAccm INTEGER
  ctPppLcpExtEchoRequest INTEGER
  ctPppLcpExtReplyCounter INTEGER
  ctPppLcpExtMpCapable INTEGER

CtPppBncpExtEntry  
SEQUENCE    
  ctPppBncpExtIfIndex INTEGER
  ctPppBncpExtCrcStatus INTEGER

CtPppMpExtEntry  
SEQUENCE    
  ctPppMpExtIfIndex INTEGER
  ctPppLcpExtMpLUT INTEGER
  ctPppLcpExtMpHistoryTime INTEGER
  ctPppLcpExtMpMoreBW INTEGER
  ctPppLcpExtMpLessBW INTEGER
  ctPppLcpExtMpMaxChannels INTEGER
  ctPppLcpExtMpChannelsToAdd INTEGER
  ctPppLcpExtMpChannelsToRemove INTEGER

CtPppEcpExtEntry  
SEQUENCE    
  ctPppEcpExtIfIndex INTEGER
  ctPppEcpKey DisplayString
  ctPppEcpIV DisplayString

CtWanalyzerEntry  
SEQUENCE    
  ctWanalyzerIfIndex INTEGER
  ctWanalyzerEnabled INTEGER
  ctWanalyzerMaxEntries INTEGER
  ctWanalyzerClearAll INTEGER
  ctWanalyzerClearInterface INTEGER
  ctWanalyzerDisplayInterface INTEGER
  ctWanalyzerCurrEntries INTEGER

WanalyzerEntry  
SEQUENCE    
  wanMessageIndex INTEGER
  wanMessageInterfaceIndex INTEGER
  wanMessageDate DisplayString
  wanMessageTime DisplayString
  wanMessageCode INTEGER

Ds1AlarmConfigEntry  
SEQUENCE    
  ds1PhysNum INTEGER
  ds1AlarmAdmin INTEGER
  ds1AlarmAutoRecovery INTEGER
  ds1AlarmTrapEnable INTEGER
  ds1AlarmESCount INTEGER
  ds1AlarmESInterval INTEGER
  ds1AlarmBPVErrorRate INTEGER
  ds1AlarmBPVInterval INTEGER
  ds1AlarmManualRecovery INTEGER

IpPQAddressEntry  
SEQUENCE    
  ipPQAddressId INTEGER
  ipPQIPAddress IpAddress

CtDs3ExtensionsEntry  
SEQUENCE    
  ctDs3ExtensionsEntryIndex INTEGER
  ctDs3ExtensionsNumInterfaces INTEGER
  ctDs3ExtensionsLineBuildOut INTEGER

Defined Values

cabletron 1.3.6.1.4.1.52
OBJECT IDENTIFIER    

mibs 1.3.6.1.4.1.52.4
OBJECT IDENTIFIER    

ctron 1.3.6.1.4.1.52.4.1
OBJECT IDENTIFIER    


ctronWan 1.3.6.1.4.1.52.4.1.2.7
OBJECT IDENTIFIER    

ctRemoteAccess 1.3.6.1.4.1.52.4.1.2.7.2
OBJECT IDENTIFIER    

ctRemoteConnection 1.3.6.1.4.1.52.4.1.2.7.2.1
OBJECT IDENTIFIER    

ctDs1Ext 1.3.6.1.4.1.52.4.1.2.7.2.2
OBJECT IDENTIFIER    

ctRs232Ext 1.3.6.1.4.1.52.4.1.2.7.2.3
OBJECT IDENTIFIER    

ctFrDcp 1.3.6.1.4.1.52.4.1.2.7.2.4
OBJECT IDENTIFIER    

ctDDSExt 1.3.6.1.4.1.52.4.1.2.7.2.5
OBJECT IDENTIFIER    

ctPPPExt 1.3.6.1.4.1.52.4.1.2.7.2.6
OBJECT IDENTIFIER    

ctWanalyzer 1.3.6.1.4.1.52.4.1.2.7.2.7
OBJECT IDENTIFIER    

ctDs1Alarms 1.3.6.1.4.1.52.4.1.2.7.2.8
OBJECT IDENTIFIER    

ctIPPQFilters 1.3.6.1.4.1.52.4.1.2.7.2.9
OBJECT IDENTIFIER    

ctDs3Ext 1.3.6.1.4.1.52.4.1.2.7.2.10
OBJECT IDENTIFIER    

ctRemNumConnections 1.3.6.1.4.1.52.4.1.2.7.2.1.1
This object describes the number of physical remote access connections on the platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctRemPhysPortTable 1.3.6.1.4.1.52.4.1.2.7.2.1.2
A list of the descriptions of the physical remote access ports of this platform.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtRemPhysPortEntry

ctRemPhysPortEntry 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1
A physical port entry. It contains objects relating to a given physical remote access port
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtRemPhysPortEntry  

ctRemConnectionIndex 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.1
A value indicating the remote connection this entry is located on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctRemPhysPortType 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.2
The type of physical port that this entry describes. None indicates that the physical port has no connector.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), t1(2), e1(3), synchronous(4), dds(5), di(6), hdsl(7), isdnBRI(8), ds30(9), t1dds(10)  

ctRemPhysPortSpecificMib 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.3
This object identifies an instance of the index object in the first group of objects in the MIB specific to the physical port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

ctRemPhysPortProtMgrType 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.4
This object identifies an instance of the type of Protocol Manager residing on this physical port. Before a physical port may be used, the type of manager must be designated. For example, if the physical port was going to be used as an ISDN PRI interface, with dial up PPP links, then the manager type would be set to (4), ISDN-PRI-PPP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), pppNailedUp(2), isdnPriPpp(3), isdnBriPpp(4), frameRelayPvcRtr(5), frameRelayPvcSw(6), hdlc(7)  

ctRemPhysPortProtMgrIfaceNum 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.5
This object identifies the interface number that will be assigned to the Protocol Managers IFO
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemPhysPortWanIfaceNum 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.6
This object identifies the interface number that will be assigned to the Wanio's IFO
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctRemPhysPortProtMgrMaxIfos 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.7
This object identifies the maximum number of IFO's that can be created on this physical interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemPhysPortProtMgrIfaceList 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.8
This object identifies a list of interfaces that will be assigned to this Protocol Managers data IFO's
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ctRemPhysAlarmTimeOut 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.9
Whenever the physical port is configured for nailed-up PPP this object specifies the time the physical port must remain in a failed state as a condition to begin the backup procedure. The backup procedure is begun for any active interface(s) that were connected over the failed physical port and which have been configured for backup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemPhysWpimType 1.3.6.1.4.1.52.4.1.2.7.2.1.2.1.10
This Mib object determines the Mode of operation that the T1/DDS Wpim module will function as. Setting a value of 1 will set the mode to DDS, setting a value of 2 will set the mode to T1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemInterfaceTable 1.3.6.1.4.1.52.4.1.2.7.2.1.3
The interface table for Cabletron remote interfaces. It is a list of items that are pertinant to the interfaces that are part of remote physical ports. The number of entries is dependent upon the total number of remote interfaces configured.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtRemInterfaceEntry

ctRemInterfaceEntry 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1
A remote interface entry. It contains objects relating to an interface that is defined for remote Cabletron products.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtRemInterfaceEntry  

ctRemIntEntIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.1
The ifIndex of the interface. This is the index of this entry in the ifTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctRemIntEntCompression 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.2
This flag will indicate whether compression should take place on this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ctRemIntEntCompRatio 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.3
This string indicates the current compression ratio on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ctRemIntEntCompStatus 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.4
This flag will indicate whether compression has been nogotiated on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ctRemIntEntMTU 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.5
The MTU to be negotiated for this interface. This will not be updated with the actual MTU, which can be found in the ifTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemIntEntCongestion 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.6
This object identifies the Leaky Bucket algorithm flag for a Frame Relay circuit on this intertface. The option is supported when this flag is enabled, and not supported when this flag is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctRemIntEntMaxProfiles 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.7
This object specifies the maximum number of neighbor profiles. A neighbor profile describes a possible connection. The maximum should be set to account for support of PPP multilink. That is to say, if PPP multilink is being used then the number of profiles must at least accomodate the maximum possible number of additional more BW connections. As such, each neighbor profile would then describe a possible connection to the same remote end point.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemIntEntTxIdleTimeout 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.8
This object identifies the idle timeout value in which a packet needs to be transmitted before the interface is automatically disconnected. Allowed values are in increments of five seconds including zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemIntEntRxIdleTimeout 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.9
This object identifies the idle timeout in which a packet needs to be received before the interface is automatically disconnected. Allowed values are in increments of five seconds including zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemIntEntCircuitName 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.10
This object associates a circuit name with a specific interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

ctRemIntEntEncryption 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.11
This flag will indicate whether encryption should take place on this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ctRemIntEntEncryptStatus 1.3.6.1.4.1.52.4.1.2.7.2.1.3.1.12
This flag will indicate whether Encryption has been nogotiated on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

ctRemPrimaryInterfaceTable 1.3.6.1.4.1.52.4.1.2.7.2.1.4
The interface table for Cabletron remote interfaces. It is a list of items that are pertinant to the interfaces that are part of remote physical ports. The number of entries is dependent upon the total number of remote interfaces configured.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtRemPrimaryInterfaceEntry

ctRemPrimaryInterfaceEntry 1.3.6.1.4.1.52.4.1.2.7.2.1.4.1
A remote interface entry. It contains objects relating to an interface that is defined for remote Cabletron products.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtRemPrimaryInterfaceEntry  

ctRemPriIntEntIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.1.4.1.1
The ifIndex of the interface. This is the index of this entry in the ifTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctRemPriIntEntConnectRetryInterval 1.3.6.1.4.1.52.4.1.2.7.2.1.4.1.2
This object specifies the interval in seconds between retries for restoring the primary interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemBackupInterfaceTable 1.3.6.1.4.1.52.4.1.2.7.2.1.5
The interface table for Cabletron remote interfaces. It is a list of items that are pertinant to the interfaces that are part of remote physical ports. The number of entries is dependent upon the total number of remote interfaces configured.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtRemBackupInterfaceEntry

ctRemBackupInterfaceEntry 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1
A remote interface entry. It contains objects relating to an interface that is defined for remote Cabletron products.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtRemBackupInterfaceEntry  

ctRemIntEntBackupIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.1
The ifIndex of the interface. This is the index of this entry in the ifTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctRemIntEntBackupIfNum 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.2
This object identifies which ifIndex will backup this interface in the event of a communications failure.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemIntEntBackupIfInUseCnt 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.3
This object identifies how many other interfaces this interface will backup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctRemIntEntBackupIfTimeToConnect 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.4
This object identifies how long to wait in seconds before attempting to switchover to the backup interface. Allowed values are in increments of five seconds including zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemIntEntBackupIfTimeToDisconnect 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.5
This object identifies how long to wait in seconds before attempting to switchover to the primary interface. Allowed values are in increments of five seconds including zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemIntEntBackupIfOverride 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.6
This object identifies if the interface will switch back to the primary link after it has become active again. A force condition will not allow the interface to switch back.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctRemIntEntBackupConnectRetries 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.7
This object specifies the number of tries to bring-up the backup interface before giving up.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemIntEntBackupConnectRetryInterval 1.3.6.1.4.1.52.4.1.2.7.2.1.5.1.8
This object specifies the interval in seconds between retries for bringing up backup interface before giving up.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemExtPhysPortTable 1.3.6.1.4.1.52.4.1.2.7.2.1.6
A list of the descriptions of the physical remote access ports of this platform.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtRemExtPhysPortEntry

ctRemExtPhysPortEntry 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1
A physical port entry. It contains objects relating to a given physical remote access port
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtRemExtPhysPortEntry  

ctRemExtConnectionIndex 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.1
A value indicating the remote connection this entry is located on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctRemExtProtMgrIndex 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.2
A value indicating the protMgr number for this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctRemExtPhysPortProtMgrType 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.3
This object identifies an instance of the type of Protocol Manager residing on this physical port. Before a physical port may be used, the type of manager must be designated. For example, if the physical port was going to be used as an ISDN PRI interface, with dial up PPP links, then the manager type would be set to (4), ISDN-PRI-PPP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), pppNailedUp(2), isdnPriPpp(3), isdnBriPpp(4), frameRelayPvcRtr(5), frameRelayPvcSw(6), hdlc(7)  

ctRemExtPhysPortProtMgrEnable 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.4
This object identifies an instance of the the enable flag of Protocol Manager residing on this physical port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctRemExtPhysPortProtMgrIfaceNum 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.5
This object identifies the interface number that will be assigned to the Protocol Managers IFO
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemExtPhysPortProtMgrMaxIfos 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.6
This object identifies the maximum number of IFO's that can be created on this physical interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctRemExtPhysPortProtMgrIfaceList 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.7
This object identifies a list of interfaces that will be assigned to this Protocol Managers data IFO's
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ctRemExtPhysPortProtMgrChannelList 1.3.6.1.4.1.52.4.1.2.7.2.1.6.1.8
This object identifies a list of channles/timeslots that will be assigned to this Protocol Managers data IFO's
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ctDs1ExtensionsTable 1.3.6.1.4.1.52.4.1.2.7.2.2.1
This table is an extension to the standard ds1 configuration table. It is a list of items that are pertinant to ds1 ports on a platform. There is one entry per ds1 physical port on the platform.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtDs1ExtensionsEntry

ctDs1ExtensionsEntry 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1
A ds1 extensions entry containing objects relating to the particular ds1 physical port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtDs1ExtensionsEntry  

ctDs1ExtensionsEntryIndex 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.1
A unique value for each ds1 physical port on the platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctDs1ExtensionsNumInterfaces 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.2
The number of interfaces on this physical port. This number inidicates the number of entries this physical port uses in the ifTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctDs1ExtensionsToggleFracTable 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.3
Setting this object to 1 will cause the Ds1 Fractional Table to be updated with the new values, as entered. Setting this object to 2, will cause the Ds1 Fractional Table to view as the table being entered. Setting this object to 3, will cause the Ds1 Fractional Table to be the table that is currently in use, regardless of any changes being entered. Setting this object to 4, will cause any changes that have been made to the Ds1 Fractional Table since the last update-table to be deleted. For physical ports that are of type synch, or for Ds1 ports that do not support the Ds1 Fractional Table, this object will have no affect, and will always return a 1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER update-table(1), display-new(2), display-old(3), restore-old(4)  

ctDs1ExtensionsLineBuildOut 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.4
The line build out setting for this ds1 physical port. Unknown indicates that the setting is neither readable or writable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), zero(2), minus-7point5(3), minus-15(4), a133to266feet(5), a266to399feet(6), a399to533feet(7), a533to655feet(8)  

ctDs1ExtensionsCFADuration 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.5
The length of time (in seconds), that the ds1 port will remain in the Carrier Failure Alarm state after the alarm condition has cleared. For those Ds1 ports not supporting Carrier Failure Alarm duration, this object always returns 1, and setting the object has no effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

ctDs1ExtensionsDIEnable 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.6
Enables or disables Drop and Insert functionality on a D/I WPIM. If enabled, all zero assigned timeslots will designate D/I interface channels, if disabled all zero channels will designate dummy channels as on a T1 or E1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ctDs1ExtensionsTotalValidIntervals 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.7
The number of previous intervals for which valid data was collected for the DS1 mib, which is currently RFC1406. This counter is similar to RFC1406 dsx1ValidIntervals except that the count represents the total number of complete 15 minute intervals since the ds1 interface has been online, and does not stop at the 24 hour period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wanDs1ExtensionsBertTestMode 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.8
This object is used to request that a type of process be in control of the testing function. This is used to differentiate between automated test procedures and those manually controlled by a user. When read, this object reflects which type of process is actually in control of the testing function. The implementation is free to prioritize or deny requests in a proprietary manner.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), internal(2), manual(3)  

wanDs1ExtensionsBertRun 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.9
Controls the sending of test data over this physical port. The data is a pattern described by wanDs1ExtensionsBertTestPattern.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

wanDs1ExtensionsBertCurrentResults 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.10
Indicates the results of the testing for the last completed sampling period. A non-negative number is the error rate in bits per million bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsBertCumulativeResults 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.11
Indicates the total number of errors since the testing was enabled. It is not a rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsBertPeakResults 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.12
Indicates the highest value of wanDs1ExtensionsBertCurrentResults since the testing was enabled. A non-negative number is the error rate in bits per million bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsBertAverageResult 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.13
Indicates the average value of wanDs1ExtensionsBertCurrentResults since the testing was enabled. A non-negative number is the error rate in bits per million bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsBertTestPattern 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.14
This object is used to specify the pattern of the test data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER patternOther(1), pattern1s(2), pattern63(3), pattern511(4), pattern2047(5), pattern3in24(6), patternQRSS(7)  

wanDs1ExtensionsBertSamplePeriod 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.15
This object is the duration of time in seconds at which the current test results will be periodically written to wanDs1ExtensionsBertCurrentResults. The range is 1 to 3600, with a default value of 10.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wanDs1ExtensionsBertNumPeriods 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.16
The number of sampling periods that have elapsed during the current test run.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wanDs1ExtensionsBertTestTraps 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.17
This object is used to enable or disable the sending of a trap at the conclusion of the measurement period. The trap will contain the information described by ctDs1BertCurrentResults. The default value is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

wanDs1ExtensionsBertDataStatus 1.3.6.1.4.1.52.4.1.2.7.2.2.1.1.18
This object provides the operating status of the transmission of test data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(1), waitingForLink(2), waitingForLoopback(3), running(4)  

ctDs1WanDriverTable 1.3.6.1.4.1.52.4.1.2.7.2.2.2
This table is an extension to the standard ds1 configuration table. It is a list of items that are pertinant to the hdlc driver on a platform. There is one entry per ds1 physical port on the platform.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtDs1WanDriverEntry

ctDs1WanDriverEntry 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1
A ds1 wan driver entry containing objects relating to the particular ds1 physical port pertaining to a specific channel on the wan driver chip.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtDs1WanDriverEntry  

ctDs1WanDriverEntryIndex 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.1
A unique value for each ds1 physical port on the platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctDs1WanDriverChannelIndex 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.2
A unique value for each channel on a wan driver on the platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctDs1WanDriverLineCode 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.3
This object controls the individual channels line coding on a wan driver device on the platform.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), jBZS(2), invHDLC(3)  

ctDs1WanDriverCRCBits 1.3.6.1.4.1.52.4.1.2.7.2.2.2.1.4
This object controls the individual channels CRC bits generation on a wan driver device on the platform.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER crc16(1), crc32(2)  

ctRs232ExtensionsTable 1.3.6.1.4.1.52.4.1.2.7.2.3.1
This table is an extension to the standard rs232-like mib. It is a list of items that are pertinant to rs232-like ports on a platform. There is one entry per synchronous physical port on the platform.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtRs232ExtensionsEntry

ctRs232ExtensionsEntry 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1
A rs232-like extensions entry containing objects relating to the particular rs232-like physical port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtRs232ExtensionsEntry  

ctRs232ExtensionsEntryIndex 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.1
A unique value for each rs232-like physical port on the platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctRs232ExtensionsCTSEnable 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.2
This object indicates whether the platform should generate CTS. When disabled the platform will not generate CTS, when enabled, the platform will generate CTS. The actual state of the CTS line is available in the rs-232 like mib.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ctRs232ExtensionsDSREnable 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.3
This object indicates whether the platform should generate DSR. When disabled the platform will not generate DSR, when enabled, the platform will generate DSR. The actual state of the DSR line is available in the rs-232 like mib.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ctRs232ExtensionsRTSEnable 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.4
This object indicates whether the platform should generate RTS. When disabled the platform will not generate RTS, when enabled, the platform will generate RTS. The actual state of the RTS line is available in the rs-232 like mib.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ctRs232ExtensionsDTREnable 1.3.6.1.4.1.52.4.1.2.7.2.3.1.1.5
This object indicates whether the platform should generate DTR. When disabled the platform will not generate DSR, when enabled, the platform will generate DTR. The actual state of the DTR line is available in the rs-232 like mib.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

frDcpCircuitTable 1.3.6.1.4.1.52.4.1.2.7.2.4.1
A table containing data compression information about specific Data Link Connection Identifiers and corresponding virtual circuit. This information is used to support the frCircuitTable following RFC-1315.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDcpCircuitEntry

frDcpCircuitEntry 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1
The data compression information regarding a single Data Link Connection Identifier.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDcpCircuitEntry  

frDcpCircuitIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.1
The ifIndex value of ifEntry that this DCP virtual circuit object is layered onto.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Index  

frDcpCircuitDlci 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.2
The Data Link Connection Identifier for this DCP virtual circuit object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DLCI  

frDcpCircuitEnable 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.3
Indicates whether data compression should take place on this particular end side virtual circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

frDcpCircuitStatus 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.4
On indicates that the compression has been successfully negotiated and is operating. Off indicates that the compression negotiation has failed and compression is not operating at this time, or compression has been terminated by either peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

frDcpCircuitRatio 1.3.6.1.4.1.52.4.1.2.7.2.4.1.1.5
The ratio of uncompressed to compressed transmitted data. If the data compression status is off, 1:1 will be displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(5)  

ctDDSConfigTable 1.3.6.1.4.1.52.4.1.2.7.2.5.1
The DDS Configuration Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtDDSConfigEntry

ctDDSConfigEntry 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1
An Entry in the DDS Configuration Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtDDSConfigEntry  

ctDDSLineIndex 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.1
A unique value for each ds1 physical port on the platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ctDDSIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.2
Index associated with this dds physical port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

ctDDSLineMode 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.3
DDS-PRI is full duplex 56k link, No framing in loop data so loop speed is also 56k. Data stream: --d1 d2 d3 d4 d5 d6 d7-- DDS-SC is also full duplex 56k link, requires framing bits to distinguish between primary and secondary channels. --d1 d2 d3 d4 d5 d6 d7 F C/S-- where F is framing bit and C/S for secondary channel as well as used for control bit. With these two extra bits the loop speed is increased to 72k. primary channel rate is 56k. DDS-CC is full duplex 64k link. Does not require framing bit but uses a same format as SC, nineth bit position is lumped with primary channel and not used for control. Loop speed is 72k, Primary channel rate is 64k. --d1 d2 d3 d4 d5 d6 d7 F d8--
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ddsPri(1), ddsSc(2), ddsCc(3)  

ctDDSLineCoding 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.4
This object describes the variety of Zero Code suppression on this interface. JBZS refers to Jammed Bit Zero suppresion, which forces a 1 bit every 8 bit periods. None refers to a mode in which some other means is used to insure pulse density requirements.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ddsNone(1), ddsJBZS(2), otherLineCode(3)  

ctDDSLoopbackConfig 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.5
This variable represents the loopback configuration of the DDS interface. ddsNoLoop means the interface is not in loopback state, ddsLocalLoop means the signal is transmitted and looped back to the same interface, ddsLineLoop means the received signal at this interface does not go through the device but is looped back out, and ddsOtherLoop represents a loop not defined here.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ddsNoLoop(1), ddsLocalLoop(2), ddsLineLoop(3), ddsOtherLoop(4)  

ctDDSLineStatus 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.6
This variable describes the current operational status of DDS line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ddsNoAlarm(1), ddsLossOfSignal(2), ddsOutOfService(3), ddsOutOfFrame(4)  

ctDDSTxClockSource 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.7
The source of Transmit clock. 'ddsLoopTiming' indicates that the recovered receive clock is used as transmit clock. 'ddsLocalTiming' indicates that a local clock source is used. 'ddsThroughTiming' indicates that recovered receive clock from another interface is used as transmit clock.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ddsLoopTiming(1), ddsLocalTiming(2), ddsThroughTiming(3)  

ctDDSPortInSpeed 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.8
This variable describes the current operational receive speed of DDS line. It is a read only value based entirely on DDS type (CC or PRI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctDDSPortOutSpeed 1.3.6.1.4.1.52.4.1.2.7.2.5.1.1.9
This variable describes the current operational transmit speed of DDS line. It is a read only value based entirely on DDS type CC or PRI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctPppCountersTable 1.3.6.1.4.1.52.4.1.2.7.2.6.1
Table containing the parameters for the local PPP entity related to the counters and timers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtPppCountersEntry

ctPppCountersEntry 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1
PPP counter/timer information for a particular PPP link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtPppCountersEntry  

ctPppCountersIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.1
The ifIndex of the interface. This is the index of this entry in the ifTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

ctPppCountersMaxTerminate 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.2
MaxTerminate indicates the number of Terminate- Request packets sent without receiving a Terminate-Ack before assuming that the peer in unable to respond.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

ctPppCountersMaxConfigure 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.3
MaxConfigure indicates the number of Configure- Request packets sent without receiving a Configure-Ack, Configre-Nak or Configure-Reject before assuming that the peer in unable to respond.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

ctPppCountersMaxFailure 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.4
MaxFailure indicates the number of Configure-Nak packets sent without sending a Configure-Ack before assuming that the configuration is not converging. Any further Configure-Reject packets for peer requested options are converted to Configure-Reject packets, and locally desires options are no longer appended.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

ctPppCountersRestartTimer 1.3.6.1.4.1.52.4.1.2.7.2.6.1.1.5
The Restart timer is used to time transmissions of Configure-Request and Terminate-Request packets. Expiration of the Restart-Timer causes a Timeout event, and retransmission of the corresponding Configure-Request or Terminate-Request packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

ctPppLcpExtTable 1.3.6.1.4.1.52.4.1.2.7.2.6.2
Table containing the parameters for the local PPP entity related to the counters and timers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtPppLcpExtEntry

ctPppLcpExtEntry 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1
PPP LCP configurationinformation for a particular PPP link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtPppLcpExtEntry  

ctPppLcpExtIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.1
The ifIndex of the interface. This is the index of this entry in the ifTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

ctPppLcpExtAuthenticationProt 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.2
Enables a particular authentication protocol on this PPP link(now modified for read-only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), pap(2), chap(3)  

ctPppLcpExtQualityProt 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.3
Enables a particular link-quality protocol on this PPP link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), lqr(2)  

ctPppLcpExtPFC 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.4
Enables protocol field compression on this PPP link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctPppLcpExtACFC 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.5
Enables address and control field compression on this PPP link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctPppLcpExtSelfDescribePadding 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.6
This Configuration Option provides a method for an implementation to indicate to the peer that it understands self-describing pads when padding is added at the end of the PPP Information field.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..256  

ctPppLcpExtCallback 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.7
This Configuration Option provides a method for an implementation to request a dial-up peer to call back.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..6  

ctPppLcpExtCompoundFrames 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.8
This Configuration Option provides a method for an implementation to send multiple PPP encapsulated packets within the same frame.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctPppLcpExtMru 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.9
Enables and disables Mru status.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctPppLcpExtAccm 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.10
Enables and disables Accm status.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctPppLcpExtEchoRequest 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.11
A zero indicated no Echo Request and any other value provides an interval to send Echo-Requests to the Peer. The Echo-Request provides a Data Link Layer loopback mechanism for use in exercising both directions of the link. This is useful in debugging, link quality determination. LCP MUST be in the OPENED state for an Echo-Request to occur.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

ctPppLcpExtReplyCounter 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.12
Increments a counter if the Local Device correctly received an Echo-Reply from the Peer. LCP MUST be in the OPENED state for an Echo-Reply to occur.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

ctPppLcpExtMpCapable 1.3.6.1.4.1.52.4.1.2.7.2.6.2.1.13
Multilink Protocol (MP) option selector. Set to a value of one when MP support is desired otherwise set to a value of two. The default value is two. When set to two the attempt is made to negotiate MP support. MP support is symmetrical.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctPppBncpExtTable 1.3.6.1.4.1.52.4.1.2.7.2.6.3
Table containing the parameters for the local PPP entity related to the counters and timers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtPppBncpExtEntry

ctPppBncpExtEntry 1.3.6.1.4.1.52.4.1.2.7.2.6.3.1
PPP LCP configuration information for a particular PPP link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtPppBncpExtEntry  

ctPppBncpExtIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.6.3.1.1
The ifIndex of the interface. This is the index of this entry in the ifTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

ctPppBncpExtCrcStatus 1.3.6.1.4.1.52.4.1.2.7.2.6.3.1.2
Enables and disables CRC status. First our platform must support CRC. If the platform does, then setting to disabled will not send CRC. The default is enabled, which sends CRC.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctPppMpExtTable 1.3.6.1.4.1.52.4.1.2.7.2.6.4
Table containing the parameters for the local PPP entity related to the counters and timers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtPppMpExtEntry

ctPppMpExtEntry 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1
PPP LCP configurationinformation for a particular PPP link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtPppMpExtEntry  

ctPppMpExtIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.1
The ifIndex of the interface. This is the index of this entry in the ifTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

ctPppLcpExtMpLUT 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.2
Used to set the Line Utilization Threshold (LUT) % value to compare against the linear weighted percentage by which to determine when more/less bandwidth is to be added/removed. Linear weighting is averaged over the period of time specified by ctPppLcpExtMpHistoryTime.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

ctPppLcpExtMpHistoryTime 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.3
Used to set the history time value in seconds for the number of line utilization reading(s) desired to compute the average line utilization. That is to say, it specifies the window size over which to compute the average line utilization.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

ctPppLcpExtMpMoreBW 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.4
Used to set the number of consecutive line utilization average readings that must exceed ctPppLcpExtMpLUT as a condition of when to increase the bandwidth if more BW is permitted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

ctPppLcpExtMpLessBW 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.5
Used to set the number of consecutive line utilization average readings that must fall below ctPppLcpExtMpLUT as a condition of when to remove possible previously added bandwidth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

ctPppLcpExtMpMaxChannels 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.6
Used to set the maxium number of channels an MP capable connection is allowed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

ctPppLcpExtMpChannelsToAdd 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.7
Used to set the number of additional channel(s) to increment by whenever the need for more bandwidth is determined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

ctPppLcpExtMpChannelsToRemove 1.3.6.1.4.1.52.4.1.2.7.2.6.4.1.8
Used to set the number of channel(s) to decrement by whenever the need for possible previously added bandwidth is determined to no longer be needed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

ctPppEcpExtTable 1.3.6.1.4.1.52.4.1.2.7.2.6.5
Table containing the parameters for the local PPP entity related to the encrpytion control protocol.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtPppEcpExtEntry

ctPppEcpExtEntry 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1
PPP ECP configuration information for a particular PPP link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtPppEcpExtEntry  

ctPppEcpExtIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1.1
The ifIndex of the interface. This is the index of this entry in the ifTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..1024  

ctPppEcpKey 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1.2
A 56-bit key (14 hex characters) used for the DES encryption.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(14)  

ctPppEcpIV 1.3.6.1.4.1.52.4.1.2.7.2.6.5.1.3
A 64-bit initialization vector (16 hex characters) used for the DES encryption in CBC mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(16)  

ctWanalyzerTable 1.3.6.1.4.1.52.4.1.2.7.2.7.1
Table containing the parameters for the local Wanalyzer entity related to the configured Protocol.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtWanalyzerEntry

ctWanalyzerEntry 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1
Information for a particular interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtWanalyzerEntry  

ctWanalyzerIfIndex 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.1
The ifIndex of the interface. This is the index of this entry in the ifTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

ctWanalyzerEnabled 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.2
This Persistent Object is a flag which indicates whether or not the WANalyzer is enabled or disabled. Upon system initialization this flag defaults to disabled unless a value for this object is found in NVRAM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ctWanalyzerMaxEntries 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.3
This Persistent Object is an integer greater than 1 which specifies the maximum total number of entries which the table will handle. When the WANalyzer is enabled this value defaults to a value dependent on the implementation unless a value is found in NVRAM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctWanalyzerClearAll 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.4
When set to 2, the entire table of entries is cleared. Upon clearing of the table, this value is reset to 1. This object is not present if the WANalyzer is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctWanalyzerClearInterface 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.5
When set to 2, all entries for this MIB-II interface index will be removed from the table. Upon complete removal of those entries, this value is reset to 1. This object is not present if the WANalyzer is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctWanalyzerDisplayInterface 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.6
When set to a valid MIB-II interface number, the table displays only those entries in the table which were received from that MIB-II interface. This value is set to -1 upon initialization and indicates that entries from all interfaces will be displayed. This object is not present if the WANalyzer is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctWanalyzerCurrEntries 1.3.6.1.4.1.52.4.1.2.7.2.7.1.1.7
A non-negative integer indicating the current number of entries in the table. This object is not present if the WANalyzer is disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanalyzerMessageTable 1.3.6.1.4.1.52.4.1.2.7.2.7.2
A table containing all of the message entries for this device. If the WANalyzer is disabled, this table will not be present.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WanalyzerEntry

wanalyzerEntry 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1
A message entry in the WANalyzer table corresponding to a particular interface in a particular instance.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WanalyzerEntry  

wanMessageIndex 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.1
An integer between 1 and wanalyzerMaxEntries which indicates the overall position this entry has in the WANalyzer table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanMessageInterfaceIndex 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.2
The MIB-II interface index representing the interface which sent this message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wanMessageDate 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.3
The date when this message was received by the WANalyzer in the standard MMDDYY format.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(8)  

wanMessageTime 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.4
The time of day when this message was received by the WANalyzer in the standard HHMMSS format.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(6)  

wanMessageCode 1.3.6.1.4.1.52.4.1.2.7.2.7.2.1.5
An enumerated value representing the nature of the debug message sent by the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER wanalyzerLastMessageRepeated(1), pppAuthentication(2), pppBncpThisLayerStart(3), pppBncpThisLayerFinished(4), pppBncpThisLayerUp(5), pppBncpThisLayerDown(6), pppBncpInitializeRestartCount(7), pppBncpZeroRestartCount(8), pppBncpRcvConfReqGood(9), pppBncpRcvConfReqBad(10), pppBncpReceiveConfigureAck(11), pppBncpReceiveConfigureNak(12), pppBncpReceiveConfigureReject(13), pppBncpReceiveTerminateRequest(14), pppBncpReceiveTerminateAck(15), pppBncpReceiveCodeRejectPermitted(16), pppBncpReceiveCodeRejectCatastrophic(17), pppBncpReceiveProtocolRejectPermitted(18), pppBncpReceiveEchoRequest(19), pppBncpReceiveEchoReply(20), pppBncpReceiveDiscardRequest(21), pppBncpReceiveUnknownCode(22), pppBncpIllegalAction(23), pppBncpSendConfigureRequest(24), pppBncpSendConfigureAck(25), pppBncpSendConfigureNak(26), pppBncpSendConfigureReject(27), pppBncpSendTerminateRequest(28), pppBncpSendTerminateAck(29), pppBncpSendCodeReject(30), pppBncpSendProtocolReject(31), pppBncpSendEchoReply(32), pppBncpInitialState(33), pppBncpStartingState(34), pppBncpClosedState(35), pppBncpStoppedState(36), pppBncpClosingState(37), pppBncpStoppingState(38), pppBncpReqSentState(39), pppBncpAckRcvdState(40), pppBncpAckSentState(41), pppBncpOpenedState(42), pppBncpEthernetMacType(43), pppBncpTokenRingMacType(44), pppBncpFddiMacType(45), pppBncpBridgeIdRcvReq(46), pppBncpBridgeIdRcvNak(47), pppBncpBridgeIdRcvRej(48), pppBncpBridgeIdXmitReq(49), pppBncpMacSelectRcvReq(50), pppBncpMacSelectRcvNak(51), pppBncpMacSelectRcvRej(52), pppBncpMacSelectXmitReq(53), pppBncpTinygramRcvReq(54), pppBncpTinygramRcvNak(55), pppBncpTinygramRcvRej(56), pppBncpTinygramXmitReq(57), pppBncpLanIdRcvReq(58), pppBncpLanIdRcvNak(59), pppBncpLanIdRcvRej(60), pppBncpLanIdXmitReq(61), pppCcpThisLayerStart(62), pppCcpThisLayerFinished(63), pppCcpThisLayerUp(64), pppCcpThisLayerDown(65), pppCcpInitializeRestartCount(66), pppCcpZeroRestartCount(67), pppCcpRcvConfReqGood(68), pppCcpRcvConfReqBad(69), pppCcpReceiveConfigureAck(70), pppCcpReceiveConfigureNak(71), pppCcpReceiveConfigureReject(72), pppCcpReceiveTerminateRequest(73), pppCcpReceiveTerminateAck(74), pppCcpReceiveCodeRejectPermitted(75), pppCcpReceiveCodeRejectCatastrophic(76), pppCcpReceiveProtocolRejectPermitted(77), pppCcpReceiveEchoRequest(78), pppCcpReceiveEchoReply(79), pppCcpReceiveDiscardRequest(80), pppCcpReceiveUnknownCode(81), pppCcpIllegalAction(82), pppCcpSendConfigureRequest(83), pppCcpSendConfigureAck(84), pppCcpSendConfigureNak(85), pppCcpSendConfigureReject(86), pppCcpSendTerminateRequest(87), pppCcpSendTerminateAck(88), pppCcpSendCodeReject(89), pppCcpSendProtocolReject(90), pppCcpSendEchoReply(91), pppCcpInitialState(92), pppCcpStartingState(93), pppCcpClosedState(94), pppCcpStoppedState(95), pppCcpClosingState(96), pppCcpStoppingState(97), pppCcpReqSentState(98), pppCcpAckRcvdState(99), pppCcpAckSentState(100), pppCcpOpenedState(101), pppCcpProprietaryCompRcvReq(102), pppCcpProprietaryCompRcvNak(103), pppCcpProprietaryCompRcvRej(104), pppCcpProprietaryCompXmitReq(105), pppCcpPredictorType1RcvReq(106), pppCcpPredictorType1RcvNak(107), pppCcpPredictorType1RcvRej(108), pppCcpPredictorType1XmitReq(109), pppCcpPredictorType2RcvReq(110), pppCcpPredictorType2RcvNak(111), pppCcpPredictorType2RcvRej(112), pppCcpPredictorType2XmitReq(113), pppCcpPuddleJumperRcvReq(114), pppCcpPuddleJumperRcvNak(115), pppCcpPuddleJumperRcvRej(116), pppCcpPuddleJumperXmitReq(117), pppCcpHpPpcRcvReq(118), pppCcpHpPpcRcvNak(119), pppCcpHpPpcRcvRej(120), pppCcpHpPpcXmitReq(121), pppCcpStacLzsRcvReq(122), pppCcpStacLzsRcvNak(123), pppCcpStacLzsRcvRej(124), pppCcpStacLzsXmitReq(125), pppCcpMsPpcRcvReq(126), pppCcpMsPpcRcvNak(127), pppCcpMsPpcRcvRej(128), pppCcpMsPpcXmitReq(129), pppCcpGandalfFzaRcvReq(130), pppCcpGandalfFzaRcvNak(131), pppCcpGandalfFzaRcvRej(132), pppCcpGandalfFzaXmitReq(133), pppCcpV42bisRcvReq(134), pppCcpV42bisRcvNak(135), pppCcpV42bisRcvRej(136), pppCcpV42bisXmitReq(137), pppCcpBsdLzwRcvReq(138), pppCcpBsdLzwRcvNak(139), pppCcpBsdLzwRcvRej(140), pppCcpBsdLzwXmitReq(141), pppCcpStackDcpRcvReq(142), pppCcpStackDcpRcvNak(143), pppCcpStackDcpRcvRej(144), pppCcpStackDcpXmitReq(145), pppChapChallengeReceived(146), pppChapResponseReceived(147), pppChapSuccessReceived(148), pppChapFailureReceived(149), pppChapSuccessSent(150), pppChapFailureSent(151), pppChapChallengeSent(152), pppChapResponseSent(153), pppIpcpThisLayerStart(154), pppIpcpThisLayerFinished(155), pppIpcpThisLayerUp(156), pppIpcpThisLayerDown(157), pppIpcpInitializeRestartCount(158), pppIpcpZeroRestartCount(159), pppIpcpRcvConfReqGood(160), pppIpcpRcvConfReqBad(161), pppIpcpReceiveConfigureAck(162), pppIpcpReceiveConfigureNak(163), pppIpcpReceiveConfigureReject(164), pppIpcpReceiveTerminateRequest(165), pppIpcpReceiveTerminateAck(166), pppIpcpReceiveCodeRejectPermitted(167), pppIpcpReceiveCodeRejectCatastrophic(168), pppIpcpReceiveProtocolRejectPermitted(169), pppIpcpReceiveEchoRequest(170), pppIpcpReceiveEchoReply(171), pppIpcpReceiveDiscardRequest(172), pppIpcpReceiveUnknownCode(173), pppIpcpIllegalAction(174), pppIpcpSendConfigureRequest(175), pppIpcpSendConfigureAck(176), pppIpcpSendConfigureNak(177), pppIpcpSendConfigureReject(178), pppIpcpSendTerminateRequest(179), pppIpcpSendTerminateAck(180), pppIpcpSendCodeReject(181), pppIpcpSendProtocolReject(182), pppIpcpSendEchoReply(183), pppIpcpInitialState(184), pppIpcpStartingState(185), pppIpcpClosedState(186), pppIpcpStoppedState(187), pppIpcpClosingState(188), pppIpcpStoppingState(189), pppIpcpReqSentState(190), pppIpcpAckRcvdState(191), pppIpcpAckSentState(192), pppIpcpOpenedState(193), pppIpcpIpAddressRcvReq(194), pppIpcpIpAddressRcvNak(195), pppIpcpIpAddressRcvRej(196), pppIpcpIpAddressXmitReq(197), pppIpcpCompressionTypeRcvReq(198), pppIpcpCompressionTypeRcvRej(199), pppIpcpCompressionTypeRcvNak(200), pppIpcpCompressionTypeXmitReq(201), pppIpxcpThisLayerStart(202), pppIpxcpThisLayerFinished(203), pppIpxcpThisLayerUp(204), pppIpxcpThisLayerDown(205), pppIpxcpInitializeRestartCount(206), pppIpxcpZeroRestartCount(207), pppIpxcpRcvConfReqGood(208), pppIpxcpRcvConfReqBad(209), pppIpxcpReceiveConfigureAck(210), pppIpxcpReceiveConfigureNak(211), pppIpxcpReceiveConfigureReject(212), pppIpxcpReceiveTerminateAck(214), pppIpxcpReceiveCodeRejectPermitted(215), pppIpxcpReceiveCodeRejectCatastrophic(216), pppIpxcpReceiveProtocolRejectPermitted(217), pppIpxcpReceiveEchoRequest(218), pppIpxcpReceiveEchoReply(219), pppIpxcpReceiveDiscardRequest(220), pppIpxcpReceiveUnknownCode(221), pppIpxcpIllegalAction(222), pppIpxcpSendConfigureRequest(223), pppIpxcpSendConfigureAck(224), pppIpxcpSendConfigureNak(225), pppIpxcpSendConfigureReject(226), pppIpxcpSendTerminateRequest(227), pppIpxcpSendTerminateAck(228), pppIpxcpSendCodeReject(229), pppIpxcpSendProtocolReject(230), pppIpxcpSendEchoReply(231), pppIpxcpInitialState(232), pppIpxcpStartingState(233), pppIpxcpClosedState(234), pppIpxcpStoppedState(235), pppIpxcpClosingState(236), pppIpxcpStoppingState(237), pppIpxcpReqSentState(238), pppIpxcpAckRcvdState(239), pppIpxcpAckSentState(240), pppIpxcpOpenedState(241), pppIpxcpCompressionProtocolRcvReq(242), pppIpxcpCompressionProtocolRcvNak(243), pppIpxcpCompressionProtocolRcvRej(244), pppIpxcpCompressionProtocolXmitReq(245), pppIpxcpNetworkNumberRcvReq(246), pppIpxcpNetworkNumberRcvNak(247), pppIpxcpNetworkNumberRcvRej(248), pppIpxcpNetworkNumberXmitReq(249), pppIpxcpNodeNumberRcvReq(250), pppIpxcpNodeNumberRcvNak(251), pppIpxcpNodeNumberRcvRej(252), pppIpxcpNodeNumberXmitReq(253), pppIpxcpRoutingProtocolRcvReq(254), pppIpxcpRoutingProtocolRcvNak(255), pppIpxcpRoutingProtocolRcvRej(256), pppIpxcpRoutingProtocolXmitReq(257), pppIpxcpRouterNameRcvReq(258), pppIpxcpRouterNameRcvNak(259), pppIpxcpRouterNameRcvRej(260), pppIpxcpRouterNameXmitReq(261), pppIpxcpConfigurationCompleteRcvReq(262), pppIpxcpConfigurationCompleteRcvNak(263), pppIpxcpConfigurationCompleteRcvRej(264), pppIpxcpConfigurationCompleteXmitReq(265), pppLcpThisLayerStart(266), pppLcpThisLayerFinished(267), pppLcpThisLayerUp(268), pppLcpThisLayerDown(269), pppLcpInitializeRestartCount(270), pppLcpZeroRestartCount(271), pppLcpRcvConfReqGood(272), pppLcpRcvConfReqBad(273), pppLcpReceiveConfigureAck(274), pppLcpReceiveConfigureNak(275), pppLcpReceiveConfigureReject(276), pppLcpReceiveTerminateRequest(277), pppLcpReceiveTerminateAck(278), pppLcpReceiveCodeRejectPermitted(279), pppLcpReceiveCodeRejectCatastrophic(280), pppLcpReceiveProtocolReject(281), pppLcpReceiveEchoRequest(282), pppLcpReceiveEchoReply(283), pppLcpReceiveDiscardRequest(284), pppLcpReceiveUnknownCode(285), pppLcpIllegalAction(286), pppLcpSendConfigureRequest(287), pppLcpSendConfigureAck(288), pppLcpSendConfigureNak(289), pppLcpSendConfigureReject(290), pppLcpSendTerminateRequest(291), pppLcpSendTerminateAck(292), pppLcpSendCodeReject(293), pppLcpSendProtocolReject(294), pppLcpSendEchoReply(295), pppLcpInitialState(296), pppLcpStartingState(297), pppLcpClosedState(298), pppLcpStoppedState(299), pppLcpClosingState(300), pppLcpStoppingState(301), pppLcpReqSentState(302), pppLcpAckRcvdState(303), pppLcpAckSentState(304), pppLcpOpenedState(305), pppLcpMruRcvReq(306), pppLcpMruRcvNak(307), pppLcpMruRcvRej(308), pppLcpMruXmitReq(309), pppLcpAsyncCharMapRcvReq(310), pppLcpAsyncCharMapRcvNak(311), pppLcpAsyncCharMapRcvRej(312), pppLcpAsyncCharMapXmitReq(313), pppLcpAuthenticationRcvReq(314), pppLcpAuthenticationRcvNak(315), pppLcpAuthenticationRcvRej(316), pppLcpAuthenticationXmitReq(317), pppLcpMagicNumberRcvReq(318), pppLcpMagicNumberRcvNak(319), pppLcpMagicNumberRcvRej(320), pppLcpMagicNumberXmitReq(321), pppLcpLinkQualityRcvReq(322), pppLcpLinkQualityRcvNak(323), pppLcpLinkQualityRcvRej(324), pppLcpLinkQualityXmitReq(325), pppLcpProtCompRcvReq(326), pppLcpProtCompRcvNak(327), pppLcpProtCompRcvRej(328), pppLcpProtCompXmitReq(329), pppLcpAddrCompRcvReq(330), pppLcpAddrCompRcvNak(331), pppLcpAddrCompRcvRej(332), pppLcpAddrCompXmitReq(333), pppLcpFcs32BitRcvReq(334), pppLcpFcs32BitRcvNak(335), pppLcpFcs32BitRcvRej(336), pppLcpFcs32BitXmitReq(337), pppLcpSelfDescPaddingRcvReq(338), pppLcpSelfDescPaddingRcvNak(339), pppLcpSelfDescPaddingRcvRej(340), pppLcpSelfDescPaddingXmitReq(341), pppLcpCompoundFramesRcvReq(342), pppLcpCompoundFramesRcvNak(343), pppLcpCompoundFramesRcvRej(344), pppLcpCompoundFramesXmitReq(345), pppLcpCallbackRcvReq(346), pppLcpCallbackRcvNak(347), pppLcpCallbackRcvRej(348), pppLcpCallbackXmitReq(349), pppLexThisLayerStart(350), pppLexThisLayerFinished(351), pppLexThisLayerUp(352), pppLexThisLayerDown(353), pppLexInitializeRestartCount(354), pppLexZeroRestartCount(355), pppLexRcvConfReqGood(356), pppLexRcvConfReqBad(357), pppLexReceiveConfigureAck(358), pppLexReceiveConfigureNak(359), pppLexReceiveConfigureReject(360), pppLexReceiveTerminateRequest(361), pppLexReceiveTerminateAck(362), pppLexReceiveCodeRejectPermitted(363), pppLexReceiveCodeRejectCatastrophic(364), pppLexReceiveProtocolRejectPermitted(365), pppLexReceiveEchoRequest(366), pppLexReceiveEchoReply(367), pppLexReceiveDiscardRequest(368), pppLexReceiveUnknownCode(369), pppLexIllegalAction(370), pppLexSendConfigureRequest(371), pppLexSendConfigureAck(372), pppLexSendConfigureNak(373), pppLexSendConfigureReject(374), pppLexSendTerminateRequest(375), pppLexSendTerminateAck(376), pppLexSendCodeReject(377), pppLexSendProtocolReject(378), pppLexSendEchoReply(379), pppLexInitialState(380), pppLexStartingState(381), pppLexClosedState(382), pppLexStoppedState(383), pppLexClosingState(384), pppLexStoppingState(385), pppLexReqSentState(386), pppLexAckRcvdState(387), pppLexAckSentState(388), pppLexOpenedState(389), pppLexMacTypeSelectRcvReq(390), pppLexMacTypeSelectRcvNak(391), pppLexMacTypeSelectRcvRej(392), pppLexMacTypeSelectXmitReq(393), pppLexTinygramCompressRcvReq(394), pppLexTinygramCompressRcvNak(395), pppLexTinygramCompressRcvRej(396), pppLexTinygramCompressXmitReq(397), pppLexMacAddressRcvReq(398), pppLexMacAddressRcvNak(399), pppLexMacAddressRcvRej(400), pppLexMacAddressXmitReq(401), pppLexMacRelayRcvReq(402), pppLexMacRelayRcvNak(403), pppLexMacRelayRcvRej(404), pppLexMacRelayXmitReq(405), pppLexStatisticsRequestRcvReq(406), pppLqrSent(407), pppLqrReceived(408), pppLinkDead(409), pppLinkEstablishment(410), pppLinkTermination(411), pppNetworkLayerPhase(412), pppPapAuthenticateReqReceived(413), pppPapAuthenticateAckReceived(414), pppPapAuthenticateNakReceived(415), pppPapAuthenticateReqSent(416), pppPapAuthenticateAckSent(417), pppPapAuthenticateNakSent(418), frGotLmiPacket(500), frGotBadQ922Header(501), frGotCllmPacket(502), frInactiveReceivedPacket(503), frReceivedNlpidIpPacket(504), frSentXidPacket(505), frSentXidResponse(506), frReceivedXidPacket(507), frXidTimerExpired(508), frGotBadUi(509), frGotBadSnapPacket(510), frLinkUp(511), frLinkDown(512), frLmiStarted(513), frLmiStopped(514), frLmiSentFullStatusEnquiry(515), frLmiSentKeepAliveMessage(516), frLmiStatusResponseReceived(517), frLmiGotAnsiReportType(518), frLmiGotFullStatusReport(519), frLmiGotKeepAliveMessage(520), frLmiUnsolicitedKeepAlive(521), frLmiAsynchronousStatus(522), frLmiGotQ933AReportType(523), frLmiBadPvcStatusLength(524), frLmiT391TimeoutFs(525), frLmiT391TimeoutSe(526), frLmiT391PollFailed(527), frLmiT391PollSucceeded(528), frLmiStatusEnquiryReceived(529), frDcpMode1Initializing(530), frDcpMode1Disabled(531), frDcpMode1ControlPacketReceived(532), frDcpMode1DataPacketReceived(533), frDcpMode1RequestSent(534), frDcpMode1RequestReceived(535), frDcpMode1ResponseSent(536), frDcpMode1ResponseReceived(537), frDcpMode1Operational(538), frDcpMode1TimerExpired(539), frDcpMode2ControlPacketReceived(540), frDcpResetPacketSent(541), frDcpResetTimerExpired(542), frDcpResetAckSent(543), frDcpDictionaryQuotaExceeded(544), isdnRemoteConnectionUp(1000), isdnRemoteConnectionDown(1001), isdnActivateConnection(1002), isdnDeactivateConnection(1003), multilinkMpLinkUp(1500), multilinkMpAddBW(1501), multilinkMpRemoveBW(1502), multilinkMpSentBeginningFragment(1503), multilinkMpSentMiddleFragment(1504), multilinkMpSentEndFragment(1505), multilinkMpSentCompleteMessage(1506), multilinkMpReceivedBeginningFragment(1507), multilinkMpReceivedMiddleFragment(1508), multilinkMpReceivedEndFragment(1509), multilinkMpReceivedCompleteMessage(1510)  

ds1AlarmsGlobalConfigGroup 1.3.6.1.4.1.52.4.1.2.7.2.8.1
OBJECT IDENTIFIER    

ds1AlarmGlobalAdmin 1.3.6.1.4.1.52.4.1.2.7.2.8.1.1
Used to enable and disable the DS1 Alarm Monitoring Application for all DS1 circuits on the device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmGlobalAutoRecovery 1.3.6.1.4.1.52.4.1.2.7.2.8.1.2
Used to enable and disable the DS1 Alarm Automatic Recovery feature for all DS1 circuits on the device. For those devices that support ds1 alarm monitoring, but do not support the automatic recovery feature, this object always returns disabled, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmGlobalTrapEnable 1.3.6.1.4.1.52.4.1.2.7.2.8.1.3
Used to enable and disable the DS1 Alarm SNMP Trap generation feature for all DS1 circuits on the device. This object operates in conjunction with configuration of objects in the ctron-trap-mib.txt
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmGlobalESCount 1.3.6.1.4.1.52.4.1.2.7.2.8.1.4
Used in conjuction with ctDs1AlarmESInterval to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..300  

ds1AlarmGlobalESInterval 1.3.6.1.4.1.52.4.1.2.7.2.8.1.5
Used in conjuction with ds1AlarmGlobalESCount to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

ds1AlarmGlobalBPVErrorRate 1.3.6.1.4.1.52.4.1.2.7.2.8.1.6
Used to specify the negative exponent of 10, used in monitoring Bipolar Violations (Code Violations for E1) over intervals defined by ds1AlarmGlobalBPVInterval. For example, for a ds1AlarmGlobalBPVErrorRate value of 6 used with a ds1AlarmGlobalBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..9  

ds1AlarmGlobalBPVInterval 1.3.6.1.4.1.52.4.1.2.7.2.8.1.7
Used to specify the interval, used in monitoring Bipolar Violations (Code Violations for E1) with thresholds defined by ds1AlarmGlobalBPVErrorRate. For example, for a ds1AlarmGlobalBPVErrorRate value of 6 used with a ds1AlarmGlobalBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not detect bipolar violations, this object always returns the default, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

ds1AlarmGlobalManualRecovery 1.3.6.1.4.1.52.4.1.2.7.2.8.1.8
To cause a manual recovery to occur on all Ds1 circuits, this object is set to a 1. It is always read as a 1. The recovery will occur only when automatic recovery is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER recover(1)  

ds1AlarmConfigTable 1.3.6.1.4.1.52.4.1.2.7.2.8.2
Table containing objects used to configure DS1 alarm functionality on a per DS1 basis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Ds1AlarmConfigEntry

ds1AlarmConfigEntry 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1
A description of a single entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Ds1AlarmConfigEntry  

ds1PhysNum 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.1
The value for this object is equal to the value of a unique physical connection identifier associated with this DS1 which is clearly labeled on the device. For those products that do not have a DS1 identifier labeled on the device, the value for this object is the same as rfc1406 dsx1LineIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ds1AlarmAdmin 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.2
Used to enable and disable the DS1 Alarm Monitoring Application for this DS1 circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmAutoRecovery 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.3
Used to enable and disable the DS1 Alarm Automatic Recovery feature for this DS1 circuit. For those devices that support ds1 alarm monitoring, but do not support the automatic recovery feature, this object always returns disabled, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmTrapEnable 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.4
Used to enable and disable the DS1 Alarm SNMP Trap generation feature for this DS1 circuit. This object operates in conjunction with configuration of objects in the ctron-trap-mib.txt
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ds1AlarmESCount 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.5
Used in conjuction with ctDs1AlarmESInterval to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..300  

ds1AlarmESInterval 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.6
Used in conjuction with ctDs1AlarmESCount to set the threshold for alarm generation when the number of Errored Seconds for a specified time interval, measured in minutes, is exceeded. The default Errored Seconds alarm condition is 100 errored seconds over a 6 minute time interval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

ds1AlarmBPVErrorRate 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.7
Used to specify the negative exponent of 10, used in monitoring Bipolar Violations (Code Violations for E1) over intervals defined by ds1AlarmBPVInterval. For example, for a ds1AlarmBPVErrorRate value of 6 used with a ds1AlarmBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..9  

ds1AlarmBPVInterval 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.8
Used to specify the interval, used in monitoring Bipolar Violations (Code Violations for E1) with thresholds defined by ds1AlarmBPVErrorRate. For example, for a ds1AlarmBPVErrorRate value of 6 used with a ds1AlarmBPVInterval of 15, an alarm is generated when a 15 minute period has an average error rate which exceeds 1 Bipolar Violation (Code Violation for E1) per million bits. For those devices that support ds1 alarm monitoring but who's hardware does not support detect bipolar violations, this object always returns the default, and performs no action when written.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

ds1AlarmManualRecovery 1.3.6.1.4.1.52.4.1.2.7.2.8.2.1.9
To cause a manual recovery to occur, this object is set to a 1. It is always read as a 1. The recovery will occur only when automatic recovery is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER recover(1)  

ipPQConfigGroup 1.3.6.1.4.1.52.4.1.2.7.2.9.1
OBJECT IDENTIFIER    

ipPQAdmin 1.3.6.1.4.1.52.4.1.2.7.2.9.1.1
Used to enable and disable the IP Priority Queue Forwarding Application.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

iPPQMaxEntries 1.3.6.1.4.1.52.4.1.2.7.2.9.1.2
Returns the maximum number of IP address entries supported by the IP Priority Queue application on this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

iPPQNumEntries 1.3.6.1.4.1.52.4.1.2.7.2.9.1.3
Get the number of IP address entries currently programmed in the ipPQAddressTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

iPPQAddAddress 1.3.6.1.4.1.52.4.1.2.7.2.9.1.4
Add an IP address to the ipPQAddressTable. Always read as a 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

iPPQDelAddress 1.3.6.1.4.1.52.4.1.2.7.2.9.1.5
Delete an IP address from the ipPQAddressTable. Always read as a 0.0.0.0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipPQAddressTable 1.3.6.1.4.1.52.4.1.2.7.2.9.2
Table containing IP addresses, used in an IP Priority Queue Forwarding function.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpPQAddressEntry

ipPQAddressEntry 1.3.6.1.4.1.52.4.1.2.7.2.9.2.1
A description of a single entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpPQAddressEntry  

ipPQAddressId 1.3.6.1.4.1.52.4.1.2.7.2.9.2.1.1
A unique value identifying an element in a sequence of IP PQ address entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ipPQIPAddress 1.3.6.1.4.1.52.4.1.2.7.2.9.2.1.2
Returns an IP address associated with a specific entry in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ctDs3ExtensionsTable 1.3.6.1.4.1.52.4.1.2.7.2.10.1
This table is an extension to the standard ds3 configuration table. It is a list of items that are pertinant to ds3 ports on a platform. There is one entry per ds3 physical port on the platform.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtDs3ExtensionsEntry

ctDs3ExtensionsEntry 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1
A ds3 extensions entry containing objects relating to the particular ds3 physical port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtDs3ExtensionsEntry  

ctDs3ExtensionsEntryIndex 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1.1
A unique value for each ds3 physical port on the platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctDs3ExtensionsNumInterfaces 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1.2
The number of interfaces on this physical port. This number inidicates the number of entries this physical port uses in the ifTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctDs3ExtensionsLineBuildOut 1.3.6.1.4.1.52.4.1.2.7.2.10.1.1.3
The line build out setting for this ds3 physical port. Unknown indicates that the setting is neither readable or writable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), zeroto255feet(2), a255to450feet(3)