CTRON-FDDI-FNB-MIB

File: CTRON-FDDI-FNB-MIB.mib (37675 bytes)

Imported modules

RFC1155-SMI CTRON-MIB-NAMES RFC1213-MIB
RFC-1212

Imported symbols

Counter ctFDDIFnb DisplayString
OBJECT-TYPE

Defined Types

CtFDDIResourceEntry  
SEQUENCE    
  ctFDDIResourceSlotID INTEGER
  ctFDDIResourceID INTEGER
  ctFDDIResourceType OBJECT IDENTIFIER
  ctFDDIResourceNumbInstance INTEGER

CtFDDINonMuxCapEntry  
SEQUENCE    
  ctFDDINMSlot INTEGER
  ctFDDINMConfigID INTEGER
  ctFDDINMConfig DisplayString
  ctFDDINMConfigDesc DisplayString

CtFDDINonMuxCapEnableEntry  
SEQUENCE    
  ctFDDINMEnableSlot INTEGER
  ctFDDINMCapEnable INTEGER

CtFDDINonMuxConnectionEntry  
SEQUENCE    
  ctFDDINMConnectionSlot INTEGER
  ctFDDINMConnectionID INTEGER
  ctFDDINMSMT INTEGER
  ctFDDINMMAC INTEGER
  ctFDDINMBytes INTEGER
  ctFDDINMFrames INTEGER

CtFDDINonMuxInterfaceEntry  
SEQUENCE    
  ctFDDINMInterSlot INTEGER
  ctFDDINMNumbInterfaces INTEGER

CtFDDIMuxCapEntry  
SEQUENCE    
  ctFDDIMuxSlot INTEGER
  ctFDDIMuxConfigID INTEGER
  ctFDDIMuxConfig DisplayString
  ctFDDIMuxConfigDesc DisplayString

CtFDDIMuxCapEnableEntry  
SEQUENCE    
  ctFDDIMuxEnableSlot INTEGER
  ctFDDIMuxCapEnable INTEGER
  ctFDDIMuxMasterPortAssignmentChange Counter

CtFDDIMuxOutEntry  
SEQUENCE    
  ctFDDIMuxOutSlot INTEGER
  ctFDDIMuxOutID INTEGER
  ctFDDIMuxOutMACIndex INTEGER
  ctFDDIMuxOutSMTIndex INTEGER
  ctFDDIMuxBytes INTEGER
  ctFDDIMuxFrames INTEGER

CtFDDIMuxMasterPortEntry  
SEQUENCE    
  ctFDDIMuxMasterPortSlotID INTEGER
  ctFDDIMuxMasterPortID INTEGER
  ctFDDIMuxMasterPortAssignment INTEGER
  ctFDDIMuxMasterPortIndex INTEGER

CtFDDISerialConfigEntry  
SEQUENCE    
  ctFDDISerialSlotID INTEGER
  ctFDDISerialAdminStatus INTEGER
  ctFDDISerialOperStatus INTEGER

CtFDDIModuleFPIMEntry  
SEQUENCE    
  ctFddiFPIMSlotID INTEGER
  ctFddiFPIM INTEGER
  ctFddiFPIMStatus INTEGER
  ctFddiFPIMType OBJECT IDENTIFIER

Defined Values

ctFDDIResource 1.3.6.1.4.1.52.4.1.2.5.1.1
OBJECT IDENTIFIER    

ctFDDINonMux 1.3.6.1.4.1.52.4.1.2.5.1.2
OBJECT IDENTIFIER    

ctFDDIMux 1.3.6.1.4.1.52.4.1.2.5.1.3
OBJECT IDENTIFIER    

ctFDDISerialConfig 1.3.6.1.4.1.52.4.1.2.5.1.4
OBJECT IDENTIFIER    

ctFDDIResourceTable 1.3.6.1.4.1.52.4.1.2.5.1.1.1
This table specifies the physical resources associated with the FNB and general FNB operation for a particular module in a particular slot.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDIResourceEntry

ctFDDIResourceEntry 1.3.6.1.4.1.52.4.1.2.5.1.1.1.1
Defines a specific physical resource entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDIResourceEntry  

ctFDDIResourceSlotID 1.3.6.1.4.1.52.4.1.2.5.1.1.1.1.1
A specific instance of a slot as defined by chSlotID as defined in the chassis MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

ctFDDIResourceID 1.3.6.1.4.1.52.4.1.2.5.1.1.1.1.2
A unique index that defines a specific physcial resource for which this relationship exists. The value of this is as defined by chResourceID in the chassis MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDIResourceType 1.3.6.1.4.1.52.4.1.2.5.1.1.1.1.3
Defines the type of resource. This is the same value as chResourceType in the chassis MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

ctFDDIResourceNumbInstance 1.3.6.1.4.1.52.4.1.2.5.1.1.1.1.4
This object defines the number of instances of a physical resource. Specific resource instances are physically located from top-to-bottom on a particular module. If there are multiple 'columns' of a resource from the top to the bottom, then the numbering will start from the left side and proceed top-to-bottom in each column. For instance, the first FNB ring will be instance 1 (top in the chassis) while the second FNB ring is instance 2 (below FNB 1 in the backplane).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDINonMuxCapTable 1.3.6.1.4.1.52.4.1.2.5.1.2.1
This table describes all possible capabilities/configurations for all non-muxed FDDI configurations within the chassis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDINonMuxCapEntry

ctFDDINonMuxCapEntry 1.3.6.1.4.1.52.4.1.2.5.1.2.1.1
Describes a particular capability/configuration entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDINonMuxCapEntry  

ctFDDINMSlot 1.3.6.1.4.1.52.4.1.2.5.1.2.1.1.1
The slot within the chassis for which this configuration information is defined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

ctFDDINMConfigID 1.3.6.1.4.1.52.4.1.2.5.1.2.1.1.2
The instance of a particular configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDINMConfig 1.3.6.1.4.1.52.4.1.2.5.1.2.1.1.3
This object defines a specific valid connection configuration. It will specify the connection state of all resource instances. If an instance of a resource is not specified, then it is disconnected. Each valid configuration is encoded in an ascii string, using a specified format for interpretation. The connection specifications are in groups of four where each group defines a specific connection configuration. The terms of a connection group is defined as follows: 1st - The resource ID as defined by ctFDDIResourceID. 2nd - A specific instance of the physical resource. This will be a value between 1 and ctFDDIResourceNumbInstance for the particular resource ID in the first term. If a resource ID has more than one specific resource instance, but the whole resource can be connected, then this term will have the value '0' to signify all instances of the resource. 3rd - The connection ID for this specific physical resource. This value is the same as ctFDDINMConnectionID, and through the ctFDDINonMuxConnectionTable maps to a specific instance of SMT and MAC. For example if the value of this object is '1.1.2.2.1.1', then it states that resource 1, instance 1 is connected to connection ID 2 and resource 2, instance 1 is connected to connection ID 1 and is inserted into its FDDI ring. If a valid configuration is no connections then this object will have a value of '0.0.0'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ctFDDINMConfigDesc 1.3.6.1.4.1.52.4.1.2.5.1.2.1.1.4
This object contains a textual description of a valid connection configuration. This is a more user-friendly representation of the configuration than the ctFDDINMConfig object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ctFDDINonMuxCapEnableTable 1.3.6.1.4.1.52.4.1.2.5.1.2.2
This table describes the currently enabled configuration for each module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDINonMuxCapEnableEntry

ctFDDINonMuxCapEnableEntry 1.3.6.1.4.1.52.4.1.2.5.1.2.2.1
Describes a specific configuration enable entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDINonMuxCapEnableEntry  

ctFDDINMEnableSlot 1.3.6.1.4.1.52.4.1.2.5.1.2.2.1.1
A specific slot for which this configuration enable pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDINMCapEnable 1.3.6.1.4.1.52.4.1.2.5.1.2.2.1.2
A specific configuration that is enabled. Enabling a configuration is done by writing the value of ctFDDINMConfigID for a specific configuration to this object. This object, when read, will return the value of ctFDDINMConfigID for the presently enabled configuration.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctFDDINonMuxConnectionTable 1.3.6.1.4.1.52.4.1.2.5.1.2.3
This table defines specific information for each defined FDDI/FNB connection. This maps the third sub identifier of ctFDDINMConfig to a particular SMT and MAC instance in the 1512 FDDI MIB.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDINonMuxConnectionEntry

ctFDDINonMuxConnectionEntry 1.3.6.1.4.1.52.4.1.2.5.1.2.3.1
Defines a specific configuration connection entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDINonMuxConnectionEntry  

ctFDDINMConnectionSlot 1.3.6.1.4.1.52.4.1.2.5.1.2.3.1.1
A specific slot for which this connection entry is defined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDINMConnectionID 1.3.6.1.4.1.52.4.1.2.5.1.2.3.1.2
Describes a specific connection identifier. Valid connection identifiers are defined by the third sub-identifier in ctFDDINMConfig as identified by ctFDDINMCapEnable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDINMSMT 1.3.6.1.4.1.52.4.1.2.5.1.2.3.1.3
A specific instance of SMT for which this entry pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDINMMAC 1.3.6.1.4.1.52.4.1.2.5.1.2.3.1.4
A specific MAC that this connection entry pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDINMBytes 1.3.6.1.4.1.52.4.1.2.5.1.2.3.1.5
The bandwidth utilization in bytes per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDINMFrames 1.3.6.1.4.1.52.4.1.2.5.1.2.3.1.6
The bandwidth utilization in frames per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDINonMuxInterfaceTable 1.3.6.1.4.1.52.4.1.2.5.1.2.4
This table describs the number of interfaces defined by each non multiplexing FDDI FNB module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDINonMuxInterfaceEntry

ctFDDINonMuxInterfaceEntry 1.3.6.1.4.1.52.4.1.2.5.1.2.4.1
A specfic non multiplexing module interface definition.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDINonMuxInterfaceEntry  

ctFDDINMInterSlot 1.3.6.1.4.1.52.4.1.2.5.1.2.4.1.1
A specific slot for which this inteface entry is defined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDINMNumbInterfaces 1.3.6.1.4.1.52.4.1.2.5.1.2.4.1.2
The number of interfaces defined on this particular module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDIMuxCapTable 1.3.6.1.4.1.52.4.1.2.5.1.3.1
This table describes all possible configuration/capabilities defined for a FDDI multiplexing module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDIMuxCapEntry

ctFDDIMuxCapEntry 1.3.6.1.4.1.52.4.1.2.5.1.3.1.1
Describes a specfic FDDI multiplexor capability/configuration entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDIMuxCapEntry  

ctFDDIMuxSlot 1.3.6.1.4.1.52.4.1.2.5.1.3.1.1.1
Defines the slot within the chassis for which this multiplexed capability/configuration entry pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

ctFDDIMuxConfigID 1.3.6.1.4.1.52.4.1.2.5.1.3.1.1.2
The instance of a particular configuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDIMuxConfig 1.3.6.1.4.1.52.4.1.2.5.1.3.1.1.3
This object defines a specific valid connection configuration. It will specify the connection state of all resource instances. If an instance of a resource is not specified, then it is disconnected. Each valid configuration is encoded in an ascii string, using a specified format for interpretation. The specific connections are in groups of four where each group defines a specific connection configuration. The terms of the connection group are defined as follows: 1st - Resource ID. The value is the same as ctFDDIResourceID for a specific resource entry. 2nd - Instance of the resource. This has a value in the range of 1 to ctFDDIResourceNumbInstance. 3rd - Path of the resource as input to the multiplexor. Paths are specified as 1 for the primary ring and 2 for the secondary. 4th - This is the multiplexor output channel that this resource comes out of the multiplexor. This value is the same as a value of ctFDDIMuxOutID. 5th - Ring Connectivity. This sub-identifier describes if the given mux-in resource (sub-identifiers 1-3) is inserted into the backplane FNB ring. Valid values are 0 for no 1 for yes. So for example a value of 1.1.1.1.0.2.2.2.2.1 is resource 1, instance 1 (primary) is on mux-out 1 and it's not inserted; resource 2, instance 2 (secondary) is on mux-out 2 and is inserted into the backplane. If a valid configuration is no connections then this object will have a value of '0.0.0.0.0'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ctFDDIMuxConfigDesc 1.3.6.1.4.1.52.4.1.2.5.1.3.1.1.4
This object contains a textual description of a valid connection configuration. This is a more user-friendly representation of the configuration than the ctFDDIMuxConfig object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ctFDDIMuxCapEnableTable 1.3.6.1.4.1.52.4.1.2.5.1.3.2
This table describes the currently enabled configuration for each module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDIMuxCapEnableEntry

ctFDDIMuxCapEnableEntry 1.3.6.1.4.1.52.4.1.2.5.1.3.2.1
Describes a specific configuration enable entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDIMuxCapEnableEntry  

ctFDDIMuxEnableSlot 1.3.6.1.4.1.52.4.1.2.5.1.3.2.1.1
A specific slot for which this configuration enable pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

ctFDDIMuxCapEnable 1.3.6.1.4.1.52.4.1.2.5.1.3.2.1.2
A specific instance of the configuration that is enabled. Setting this object with a specific value of ctFDDIMuxConfigID enabled that configuration. A request of the value of this object will return the value of ctFDDIMuxConfigID for the presently enabled configuration.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctFDDIMuxMasterPortAssignmentChange 1.3.6.1.4.1.52.4.1.2.5.1.3.2.1.3
Depicts the number of changes to the master port to multiplexor output mapping.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ctFDDIMuxOutTable 1.3.6.1.4.1.52.4.1.2.5.1.3.3
Describes the multiplexor outputs for each of the FNB multiplexor modules. This maps the multiplexor output to a specific instance of MAC and SMT in the FDDI MIB.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDIMuxOutEntry

ctFDDIMuxOutEntry 1.3.6.1.4.1.52.4.1.2.5.1.3.3.1
Describes a particular multiplexor output.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDIMuxOutEntry  

ctFDDIMuxOutSlot 1.3.6.1.4.1.52.4.1.2.5.1.3.3.1.1
The given slot for which this multiplexor output information pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

ctFDDIMuxOutID 1.3.6.1.4.1.52.4.1.2.5.1.3.3.1.2
The specific instance of the multiplexor output. Instances of this object are used by the values of ctFDDIMuxConfig.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDIMuxOutMACIndex 1.3.6.1.4.1.52.4.1.2.5.1.3.3.1.3
The MAC instance of this multiplexor output. If this this object has a value greater than 0, then this value is the same as fddimibMACIndex. If this object has the value of 0, the given mux-out does not have a MAC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ctFDDIMuxOutSMTIndex 1.3.6.1.4.1.52.4.1.2.5.1.3.3.1.4
Identifies the instance of SMT as defined within the FDDI MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ctFDDIMuxBytes 1.3.6.1.4.1.52.4.1.2.5.1.3.3.1.5
The bandwidth utilization in bytes per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDIMuxFrames 1.3.6.1.4.1.52.4.1.2.5.1.3.3.1.6
The bandwidth utilization in frames per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDIMuxMasterPortTable 1.3.6.1.4.1.52.4.1.2.5.1.3.4
A list of entries that define master ports as they are defined for the given multiplexed FDDI connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDIMuxMasterPortEntry

ctFDDIMuxMasterPortEntry 1.3.6.1.4.1.52.4.1.2.5.1.3.4.1
A specific FDDI-FNB multiplexed master port definition.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDIMuxMasterPortEntry  

ctFDDIMuxMasterPortSlotID 1.3.6.1.4.1.52.4.1.2.5.1.3.4.1.1
A specific instance of a slot as defined by chSlotID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

ctFDDIMuxMasterPortID 1.3.6.1.4.1.52.4.1.2.5.1.3.4.1.2
A unique identifier for this specific master port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ctFDDIMuxMasterPortAssignment 1.3.6.1.4.1.52.4.1.2.5.1.3.4.1.3
Provides the masterport to multiplexor output mapping. This is as defined by ctFDDIMuxOutMacAssignment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

ctFDDIMuxMasterPortIndex 1.3.6.1.4.1.52.4.1.2.5.1.3.4.1.4
Defines a specific port within the FDDI MIBs fddimibPORTTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ctFDDINumbModules 1.3.6.1.4.1.52.4.1.2.5.1.4.1
Describes the number of modules that are present configurable thru the serial control portion of this MIB. This directly reflects the number of rows found within the ctFDDISerialConfigTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..14  

ctFDDISerialConfigTable 1.3.6.1.4.1.52.4.1.2.5.1.4.2
This table describes the adminstrative control over each of the FNB serial control modules.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDISerialConfigEntry

ctFDDISerialConfigEntry 1.3.6.1.4.1.52.4.1.2.5.1.4.2.1
Describes the controls over a single FNB serial control entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDISerialConfigEntry  

ctFDDISerialSlotID 1.3.6.1.4.1.52.4.1.2.5.1.4.2.1.1
Defines the slot that this FNB serial control module is in. This is an instance of chSlotID as defined in the chassis MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFDDISerialAdminStatus 1.3.6.1.4.1.52.4.1.2.5.1.4.2.1.2
Describes the adminstrative desired state for this FNB serial control module. insertFNB1(1) - The serial controlled module should be inserted into FNB-1 and bypass FNB-2. insertFNB2(2) - The serial contolled module should be inserted into FNB-2 and bypass FNB-1. insertFNB1FNB2(3) - Insert the serial controlled module on both FNBs. bypass(4) - Bypass the connection to both FNBs. hwControlFNB1(5) - Use hardware settings for FNB-1. hwControlFNB2(6) - Use hardware settings for FNB-2. hwControl(7) - Use the hardware settings for both FNBs.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER insertFNB1(1), insertFNB2(2), insertFNB1FNB2(3), bypass(4), hwControlFNB1(5), hwControlFNB2(6), hwControl(7)  

ctFDDISerialOperStatus 1.3.6.1.4.1.52.4.1.2.5.1.4.2.1.3
Describes the operational status of this FDDI serial controlled module. insertFNB1(1) - The serial controlled module is inserted into FNB-1 and bypassed from FNB-2. insertFNB2(2) - The serial controlled module is bypassed from FNB-1 and inserted into FNB-2. insertFNB1FNB2(3) - The serial controlled module is inserted into both FNB-1 and FNB-2. bypass(4) - The serial controlled module is bypassed from both FNB-1 and FNB-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER insertFNB1(1), insertFNB2(2), insertFNB1FNB2(3), bypass(4)  

ctFDDIModuleFPIMTable 1.3.6.1.4.1.52.4.1.2.5.1.4.3
This table describes the FPIMs that are on the front panel of each FDDI serial control module, if that module supports FPIMs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtFDDIModuleFPIMEntry

ctFDDIModuleFPIMEntry 1.3.6.1.4.1.52.4.1.2.5.1.4.3.1
Describes a single FDDI FPIM on a module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtFDDIModuleFPIMEntry  

ctFddiFPIMSlotID 1.3.6.1.4.1.52.4.1.2.5.1.4.3.1.1
Defines the slot in which this module exists. This is an instance of chSlotID as found in the chassis MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFddiFPIM 1.3.6.1.4.1.52.4.1.2.5.1.4.3.1.2
Defines the instance of the port for which this definition is made. Ports are physically located from top-to-bottom on a particular module. If there are multiple 'columns' of ports from the top to the bottom, then the numbering will start from the left side and proceed top-to-bottom in each column.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ctFddiFPIMStatus 1.3.6.1.4.1.52.4.1.2.5.1.4.3.1.4
Describes the link status of the given FPIM. A value of link(1) states that a link is present. A value of noLink(2) states that no link is present. A value of notSupported(3) means that link status is not supported by this port and is unknown.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER link(1), noLink(2), notSupported(3)  

ctFddiFPIMType 1.3.6.1.4.1.52.4.1.2.5.1.4.3.1.5
Describes the type of FPIM as found in ctron-oids.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER