CM-FACILITY-MIB

File: CM-FACILITY-MIB.mib (782276 bytes)

Imported modules

SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
IPV6-TC IF-MIB ENTITY-MIB
CM-ENTITY-MIB ADVA-MIB CM-COMMON-MIB
F3-LAG-MIB F3-SYNC-MIB

Imported symbols

MODULE-COMPLIANCE OBJECT-GROUP MODULE-IDENTITY
OBJECT-TYPE Integer32 Unsigned32
IpAddress Counter64 DateAndTime
DisplayString TruthValue RowStatus
StorageType MacAddress VariablePointer
TEXTUAL-CONVENTION Ipv6Address InterfaceIndex
PhysicalIndex neIndex shelfIndex
slotIndex f3UsbHostIndex networkElementEntry
fsp150cm AdminState OperationalState
SecondaryState EthernetMediaType EthernetPortSpeed
TrafficDirection SfpConnectorValue SfpMediaType
VlanId VlanPriority VlanTagType
PriorityMapMode SignalDirectionType AfpTagControl
VlanEthertype CmTrafficAclFilterActionType IpVersion
CmTrafficACLPriorityType CmTrafficAclFilterType CmTrafficAclProtocolType
TDMFrequencySourceType F3DisplayString FlowSecState
f3LagIndex SSMQualityLevel SquelchControl
TimeSource

Defined Types

CmEthernetSvcPortMode  
Describes the Ethernet Service Port Mode Type.
TEXTUAL-CONVENTION    
  INTEGER connection-oriented(1), connection-less(2)  

CmEthernetSvcType  
Describes the Ethernet Service Type. epl - Ethernet Private Linei, Port-based, all-to-one bundling evpl - Ethernet Virtual Private Line, VLAN based, service multiplexed.
TEXTUAL-CONVENTION    
  INTEGER epl(1), evpl(2)  

CmEthernetTrafficSvcType  
Describes the Ethernet Service Type, including port-based and vlan-based.
TEXTUAL-CONVENTION    
  INTEGER all-to-one(1), service-multiplexing(2)  

CmAclConfiguration  
This object is defined to set traffic acl resource allocation. Supported actions are: all-bk-l2 (1) - all bank allocated to l2. all-bk-l2-ipv4(2) - all bank allocated to l2/ipv4. two-bk-l2-ipv4(3) - two thirds allocated to l2/ipv4, the left belongs to ipv6. one-bk-l2-ipv4(4) - one thirds allocated to l2/ipv4, the left belongs to ipv6. none-bk-l2-ipv4(5) - all bank allocated to ipv6.
TEXTUAL-CONVENTION    
  INTEGER all-bk-l2(1), all-bk-l2-ipv4(2), two-bk-l2-ipv4(3), one-bk-l2-ipv4(4), none-bk-l2-ipv4(5)  

CmAfpType  
Describes the Ethernet Acceptable Framing Policy Type.
TEXTUAL-CONVENTION    
  INTEGER tagged(1), untagged(2), all(3)  

CmEthernetDiagAction  
Describes the Ethernet Diagnosis Action. autoNeg - Auto negotiation capability, cable - Cable diagnostics, cable fault loopback- Terminal loopback with traffic injection and monitoring efm-oam-lpbk- EFM OAM loopback all - autoNeg, cable tests and loopback, not include efm-oam-lpbk.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), autoneg(1), cable(2), loopback(3), efm-oam-lpbk(4), all(5)  

CmDiagCableCondType  
Describes the Ethernet Diagnosis Cable Condition Result.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), cableshort(1), cableopen(2), cableimpedance(3), cablenotfound(4), cableok(5), cablefailed(6), cablenotrun(7)  

CmDiagAutoNegCondType  
Describes the Ethernet Diagnosis Auto Negotiation Condition Result.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), autonegok(1), autonegfailed(2), autonegnotrun(3)  

CmDiagLpbkCondType  
Describes the Ethernet Diagnosis Loopback Condition Result.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), lpbkok(1), lpbkfailed(2), lpbknotrun(3)  

CmDiagEfmOamLpbkCondType  
Describes the Ethernet Diagnosis EFM OAM Loopback Condition Result.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), efmlpbkok(1), efmlpbkfailed(2), efmlpbkfailednendNA(3), efmlpbkfailedfendNA(4), efmlpbknotrun(5)  

CmDiagTestStatus  
ECPA Test Status.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), initial(1), in-progress(2), stopped(3), completed(4), aborted(5)  

CmControlProtocolFilterType  
Describes the Control Protocol Filter Types.
TEXTUAL-CONVENTION    
  INTEGER efmoam(1), pause(2)  

CmLoopbackType  
Describes the Loopback Types.
TEXTUAL-CONVENTION    
  INTEGER lpbk-none(1), efm-oam-remote(2), efm-oam-remote-timed(3), facility-port(4), facility-port-timed(5), facility-vlan(6), terminal-port(7), terminal-port-timed(8), terminal-vlan(9), efm-oam-tailend(10), facility-payload(11), facility-payload-timed(12), remote-facility(13), remote-facility-payload(14), tailend-facility(15), tailend-facility-payload(16), terminal-itag(17), facility-itag(18), jdsu-terminal-port-tailend(19), jdsu-terminal-vlan-tailend(20), jdsu-facility-port-tailend(21), jdsu-facility-vlan-tailend(22), facility-och(23), facility-och-timed(24), terminal-och(25), terminal-och-timed(26)  

CmSwapSADAType  
Describes the SWAP SADA Types supported. no-swapSADA - No swapping of Source MAC and Destination MAC swapSADA - Do swapping of Source MAC and Destination MAC swapDAOverrideSA - Swap Destination MAC as Source MAC, override source MAC with local MAC swapSADAMacOnly - Not supported swapDAOverridesSAMacOnly - Not supported swapIP - Do swapping of Source MAC and Destination MAC, Source IP and Destination IP swapTCPUDP - Do swapping of Source MAC and Destination MAC, Source IP and Destination IP, Source TCP/UDP port and Destination TCP/UDP port.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), noswapSADA(1), swapSADA(2), swapDAOverrideSA(3), swapSADAMacOnly(4), swapDAOverridesSAMacOnly(5), swapIP(6), swapTCPUDP(7)  

CmControlProtocolDispType  
Describes the Protocol Disposition Type on an interface.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), discard(1), peer(2), pass-thru(3), use-group-setting(4), not-active(5), use-port-setting(6), pass-thru-l2pt(7), useMacSetting(8)  

CmLinkLossFwdSignalType  
Describes the Link Loss Forwarding Signal Types.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), llf-efm-signal(1), llf-link-down(2), llf-odu-ais(3), llf-odu-lck(4), llf-odu-tim(5), llf-odu-bdi(6), llf-opu-plm(7), llf-opu-csf(8), llf-eth-epc(9)  

CmLinkLossFwdTriggerTypes  
Describes the Link Loss Forwarding Trigger Types.
TEXTUAL-CONVENTION    
  BITS trig-efm-signal(1), trig-link-down(2), trig-odu-ais(3), trig-odu-lck(4), trig-odu-tim(5), trig-odu-bdi(6), trig-opu-plm(7), trig-opu-csf(8)  

CmLinkLossFwdTxActionType  
Describes the Link Loss Forwarding Tx Action Types.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), llf-tx-no-action(1), llf-tx-efm-signal(2), llf-tx-link-down(3), llf-odu-ais(4), llf-opu-csf(5), llf-otu-ais(6)  

CmRemoteLinkIds  
Remote Link Ids used to match for Link Loss Forwarding.
TEXTUAL-CONVENTION    
  BITS remoteLinkId1(1), remoteLinkId2(2), remoteLinkId3(3), remoteLinkId4(4), remoteLinkId5(5), remoteLinkId6(6), remoteLinkId7(7), remoteLinkId8(8), remoteLinkId9(9), remoteLinkId10(10), remoteLinkId11(11), remoteLinkId12(12), remoteLinkId13(13), remoteLinkId14(14), remoteLinkId15(15), remoteLinkId16(16)  

CmOamMode  
Describes the OAM Mode.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), active(1), passive(2)  

CmOamAdminState  
Describes the OAM Admin State.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), enabled(1), disabled(2)  

CmOamDiscoveryState  
Describes the OAM Discovery State.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), fault(1), activesendlocal(2), passivewait(3), sendlocalremote(4), sendlocalremoteok(5), sendany(6)  

CmFlowType  
Describes the Ethernet Flow Type. portbased - Port based Flow with full bandwidth of port; this Flow does not do VLAN/MAC based processing regular - Connection-oriented, VLAN based service default - Connection-oriented, service that matches all VLANs.
TEXTUAL-CONVENTION    
  INTEGER portbased(1), regular(2), default(3)  

CmEthernetMDIXType  
Describes the Ethernet MDIX Type. auto-mdix - Auto MDIX crossed - Crossed uncrossed - Uncrossed.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(1), auto-mdix(2), crossed(3), uncrossed(4), notAvailable(5)  

FlowTrafficType  
Describes the Flow Traffic Type. shaped-only, policed-shaped, policed-only.
TEXTUAL-CONVENTION    
  INTEGER shaped-only(1), policed-shaped(2), policed-only(3)  

FlowVlanActionType  
Describes the Ethernet Flow Action. Used for adding/removing VLAN members
TEXTUAL-CONVENTION    
  INTEGER no-action(1), add-vlan(2), remove-vlan(3)  

FlowTagControl  
Describes the Ethernet Flow Tag Control Type.
TEXTUAL-CONVENTION    
  INTEGER none(1), push(2), swapvid(3), pushvid(4), pop(5), pushisid(6)  

PrioMapControlType  
Describes the Priority Mapping Control Type.
TEXTUAL-CONVENTION    
  INTEGER none(1), swap(2)  

PolicerAlgorithmType  
Describes the Policer Algorithm Type.
TEXTUAL-CONVENTION    
  INTEGER srTCM(1), trTCM(2)  

PolicerColorMode  
Describes the Policer Color Mode.
TEXTUAL-CONVENTION    
  INTEGER color-aware(1), color-blind(2)  

BitsPortType  
Enumerations for BITS Port Type. bits-in, bits-out.
TEXTUAL-CONVENTION    
  INTEGER bits-in(1), bits-out(2)  

BitsPortLineType  
Enumerations for BITS Line Type. t1, e1, 2048kHz.
TEXTUAL-CONVENTION    
  INTEGER t1(1), e1(2), type-2048kHz(3)  

BitsPortLineCode  
Enumerations for BITS Line Code. none, t1-b8zs, t1-ami, e1-hdb3, e1-ami.
TEXTUAL-CONVENTION    
  INTEGER none(1), t1-b8zs(2), t1-ami(3), e1-hdb3(4), e1-ami(5)  

BitsFrameFormat  
Enumerations for Bits Frame Format. none, t1-sf, t1-esf, e1-unframed, e1-crc4, e1-dualframe.
TEXTUAL-CONVENTION    
  INTEGER none(1), t1-sf(2), t1-esf(3), e1-unframed(4), e1-crc4(5), e1-dualframe(6)  

SaBitDesignation  
Enumerations for SA Bit Desgination. none, bit4, bit5, bit6, bit7, bit8.
TEXTUAL-CONVENTION    
  INTEGER none(1), bit4(2), bit5(3), bit6(4), bit7(5), bit8(6)  

CmActiveControlProtocolsType  
Remote Link Ids used to match for Link Loss Forwarding.
TEXTUAL-CONVENTION    
  BITS ciscoGroup(1), isl(2), pagp(3), udld(4), cdp(5), vtp(6), dtp(7), pvstpplus(8), uplinkfast(9), vlanbridge(10), l2pt(11), bridgegroup(12), bpdu(13), pause(14), lacp(15), lacpmarker(16), efmoam(17), ssm(18), portauthen(19), bridgereserved(20), lanbridges(21), garpgroup(22), gmrp(23), gvrp(24), garp(25), lldp(26), elmi(27), mac00(28), mac01(29), mac02(30), mac03(31), mac04(32), mac05(33), mac06(34), mac07(35), mac08(36), mac09(37), mac0A(38), mac0B(39), mac0C(40), mac0D(41), mac0E(42), mac0F(43), nearestlldp(44), nontpmrlldp(45), customerlldp(46), ptpNonfwdUntagged(47), ptpNonfwdTagged(48)  

PcpDEEncType  
Enumerations for PCP Drop Eligibility Encode Type. enc-none, enc-7p1d, enc-6p2d, enc-5p3d, enc-custom.
TEXTUAL-CONVENTION    
  INTEGER enc-none(1), enc-7p1d(2), enc-6p2d(3), enc-5p3d(4), enc-custom(5)  

PcpDEPairsAction  
none, apply-pairs.
TEXTUAL-CONVENTION    
  INTEGER none(0), apply-pairs(1)  

LineBuildOut  
none, 0-133ft, 133-266ft, 266-399ft, 399-533ft, 533-655ft, 7dot5db, 15db, 22dot5db.
TEXTUAL-CONVENTION    
  INTEGER none(0), lbo-0-133ft(1), lbo-133-266ft(2), lbo-266-399ft(3), lbo-399-533ft(4), lbo-533-655ft(5), lbo-7dot5db(6), lbo-15db(7), lbo-22dot5db(8)  

BitsPortImpedanceMode  
Describes the impedance mode of the BITS-IN and BITS-OUT interfaces: 120OHM.
TEXTUAL-CONVENTION    
  INTEGER bits-120Ohm(1), bits-100Ohm(2)  

ShapingType  
port-based - traffic shaping at Port level flow-based - traffic shaping at Flow level llq - low latency queuing
TEXTUAL-CONVENTION    
  INTEGER port-based(1), flow-based(2), llq(3)  

XgePhyType  
Specifies the Ethernet 10G port PHY type. not-applicable - for non-10G ports lan - 10G LAN-PHY mode (10GBASE-R) operating at 10Gb/sec wan - 10G WAN-PHY mode (10GBASE-W) operating at 9.29Gb/sec
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), lan(1), wan(2), otn(3)  

F3Usb3GDCNPINCodeActionType  
Describes the 3G Dcn Pin Code Action Types.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), enable-pin(1), disable-pin(2), change-pin(3), authentication-pin(4), unlock-pin(5)  

F3Usb3GSimCardState  
Describes the 3G Usb Sim Card States.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), ok(1), notinserted(2), networkrejected(3), unknown(4)  

F3Usb3GNetworkConnectionState  
Describes the Connection State of the 3G Usb Modem.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), connecting(1), connected(2), disconnected(3)  

F3Usb3GRecvSignalStrengthInd  
Describes the Recived Signal Strength of the 3G Usb Modem.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), high(1), medium(2), low(3), none(4)  

TrailTraceFormat  
Describes the Trail Trace Format.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), onebytemode(1), sixteenbytemode(2), sixtyfourbytemode(3)  

MultiplexingStructure  
Describes the Multiplexing Structure.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), vt-sts1(1), sts1spe-sts1(2), sts3cspe-sts3c(3), vc12-vc4-aug(4), vc12-vc3-aug(5), vc3-aug(6), vc3-vc4-aug(7), vc4-aug(8), custom(9)  

EoTDMMode  
Describes the EoTDM Mode.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), eosdh(1), eopdh(2)  

BitErrRate  
.
TEXTUAL-CONVENTION    
  INTEGER none(0), ber-1e-1(1), ber-1e-2(2), ber-1e-3(3), ber-1e-4(4), ber-1e-5(5), ber-1e-6(6), ber-1e-7(7), ber-1e-8(8), ber-1e-9(9), ber-1e-10(10)  

GFPEncapsulationType  
Describes the GFP Encapsulation of the traffic port.
TEXTUAL-CONVENTION    
  INTEGER none(0), gfp(1), gfp-fcs(2), gfp-novcat(3), gfp-zerovcat(4), gfp-fcs-novcat(5), gfp-fcs-zerovcat(6), x86(7)  

PPSInputRate  
Describes the PPS Input Rate.
TEXTUAL-CONVENTION    
  INTEGER pulse-per-sec(1), pulse-per-2sec(2)  

PPSPhyInterfaceType  
Describes the PPS physical interface type.
TEXTUAL-CONVENTION    
  INTEGER none(0), pps(1), tod(2)  

OCNSTMPortType  
OCN/STM Port Type.
TEXTUAL-CONVENTION    
  INTEGER oc12(1), oc3(2), stm4(3), stm1(4)  

E1T1LineType  
Enumerations for E1/T1 Line Type. t1, e1
TEXTUAL-CONVENTION    
  INTEGER t1(1), e1(2)  

E1T1LineCode  
Enumerations for E1/T1 Line Code. none, t1-b8zs, t1-ami, e1-hdb3, e1-ami.
TEXTUAL-CONVENTION    
  INTEGER none(1), t1-b8zs(2), t1-ami(3), e1-hdb3(4), e1-ami(5)  

E1T1FrameFormat  
Enumerations for E1/T1 Frame Format. none, t1-sf, t1-esf, e1-unframed, e1-crc4, e1-dualframe, e1-basicframe.
TEXTUAL-CONVENTION    
  INTEGER none(1), t1-sf(2), t1-esf(3), e1-unframed(4), e1-crc4(5), e1-dualframe(6), t1-unframed(7), e1-basicframe(8)  

E1T1RcvSensitivity  
Enumerations for E1/T1 Receive Sensitivity high-range, low-range
TEXTUAL-CONVENTION    
  INTEGER high-range(1), low-range(2)  

E3T3FrameFormat  
Describes the Frame Format of E3/T3.
TEXTUAL-CONVENTION    
  INTEGER none(0), dsx3CbitParity(1), g832(2), e3Unframed(3), dsx3M23(4), g751(5), dsx3Unframed(6)  

TDMPathType  
Describes the path type.
TEXTUAL-CONVENTION    
  INTEGER none(0), t1(1), e1(2), t3(3), e3(4), vc12(5), vc3(6), vc4(7), vt15(8), sts1(9), sts3c(10)  

PPSGenCondition  
Enumerations for PPS Generation Condition tracked-1sat, tracked-3sat
TEXTUAL-CONVENTION    
  INTEGER tracked-1sat(1), tracked-3sat(2)  

GPSAntennaStatus  
Enumerations for GPS Antenna Status
TEXTUAL-CONVENTION    
  INTEGER open(1), short(2), normal(3), unavailable(4)  

PolicingControl  
Defines Policing Control options.
TEXTUAL-CONVENTION    
  INTEGER a2n(1), n2a(2), a2nN2a(3), n2n(4)  

FlowConfigType  
Defines types of Flow.
TEXTUAL-CONVENTION    
  INTEGER access(1), passThru(2)  

G3AuthStatus  
Disabled (PIN protection is disabled) OK (PIN protection is enabled and PIN code is correct) Input PIN (input PIN to unlock) Input PUK (PIN code is locked, input PUK to unlock) Locked (must contact with SIM provider).
TEXTUAL-CONVENTION    
  INTEGER disabled(1), ok(2), input-pin(3), input-puk(4), locked(5), none(6)  

PsePowerLevel  
Defines the power level for pse port. class1 (4.00 Watts) :0 class2 (7.00 Watts) :1 class0andclass 3 (15.4 Watts):2 class4 (30 Watts):3.
TEXTUAL-CONVENTION    
  INTEGER class1(1), class2(2), class0andclass3(3), class4(4)  

PSENonStandardPD  
Enumerations for NonStandardPD disabled:don't support non-standard PD, enabled:support non-standard PD
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

LearningAction  
Describes Action on ingress frames when the number of MAC Table entires has reached the maximum defined by tableSize
TEXTUAL-CONVENTION    
  INTEGER block(1), forward(2)  

SfpChannelIdentifier  
Describes Channel number of WDM tunable XFP setting.
TEXTUAL-CONVENTION    
  INTEGER not-applicable(0), none(1), frequency-19610(2), frequency-19595(3), frequency-19585(4), frequency-19575(5), frequency-19565(6), frequency-19555(7), frequency-19545(8), frequency-19535(9), frequency-19525(10), frequency-19515(11), frequency-19505(12), frequency-19495(13), frequency-19485(14), frequency-19475(15), frequency-19465(16), frequency-19455(17), frequency-19445(18), frequency-19435(19), frequency-19425(20), frequency-19415(21), frequency-19405(22), frequency-19395(23), frequency-19385(24), frequency-19375(25), frequency-19365(26), frequency-19355(27), frequency-19345(28), frequency-19335(29), frequency-19325(30), frequency-19315(31), frequency-19305(32), frequency-19295(33), frequency-19285(34), frequency-19275(35), frequency-19265(36), frequency-19255(37), frequency-19245(38), frequency-19235(39), frequency-19225(40), frequency-19215(41), frequency-19205(42), frequency-19600(43), frequency-19590(44), frequency-19580(45), frequency-19570(46), frequency-19560(47), frequency-19550(48), frequency-19540(49), frequency-19530(50), frequency-19520(51), frequency-19510(52), frequency-19500(53), frequency-19490(54), frequency-19480(55), frequency-19470(56), frequency-19460(57), frequency-19450(58), frequency-19440(59), frequency-19430(60), frequency-19420(61), frequency-19410(62), frequency-19400(63), frequency-19390(64), frequency-19380(65), frequency-19370(66), frequency-19360(67), frequency-19350(68), frequency-19340(69), frequency-19330(70), frequency-19320(71), frequency-19310(72), frequency-19300(73), frequency-19290(74), frequency-19280(75), frequency-19270(76), frequency-19260(77), frequency-19250(78), frequency-19240(79), frequency-19230(80), frequency-19220(81), frequency-19210(82), frequency-19200(83), frequency-19195(84), frequency-19190(85), frequency-19185(86), frequency-19180(87), frequency-19175(88), frequency-19170(89), frequency-19165(90), frequency-19160(91), frequency-19155(92), frequency-19150(93), frequency-19145(94), frequency-19140(95), frequency-19135(96), frequency-19130(97), frequency-19125(98)  

BandwidthProfileMode  
A Network Element level Frame Rate Bandwidth Profile Mode shall be supported which will indicate if the CIR/EIR is interpreted as Information Rate (IR) or Line Rate (LR). In IR mode BWP is enforced based on number of bytes beginning with DA and ending with FCS as it was received at a port which is called the Service Frame in MEF terminology. In LR mode the BWP is enforced based on the whole frame including IFG, Preamble and SFD.
TEXTUAL-CONVENTION    
  INTEGER lineRate(1), informationRate(2)  

LearningConfigAction  
Learning Action: noAction - No Action flushFwdTable - Removes all dynamic entries from the Forwarding table of a Flow. clearBlock - removes the secondary state of BLCKD and transitions the flow to a state where frames are not blocked resetAgingTimer - reset the aging timer
TEXTUAL-CONVENTION    
  INTEGER noAction(1), flushFwdTable(2), clearBlock(3), resetAgingTimer(4)  

TrafficPortDeleteEntitiesAction  
Learning Action: no-action - No Action delete-esa-entities - Removes all esa entities relate to this port. delete-cfm-entities - Removes all cfm entities relate to this port.
TEXTUAL-CONVENTION    
  INTEGER no-action(1), delete-esa-entities(2), delete-cfm-entities(3)  

UsbDCNMobileNetworkType  
Mobile network type: none secondGeneration - 2G. thirdGeneration - 3G, fourthGeneration - 4G, notApplicable.
TEXTUAL-CONVENTION    
  INTEGER none(1), secondGeneration(2), thirdGeneration(3), fourthGeneration(4), notApplicable(5)  

TxDeiAction  
Transmit DEI Action.
TEXTUAL-CONVENTION    
  INTEGER setToZero(1), markColor(2), noChange(3)  

RxDeiAction  
Receive DEI Action.
TEXTUAL-CONVENTION    
  INTEGER ignore(1), use(2)  

DeiOuterTagType  
DEI Outer Tag Type.
TEXTUAL-CONVENTION    
  INTEGER stag(1), ctagOrStag(2)  

ConstellationType  
Constellation Type of GPS Antenna
TEXTUAL-CONVENTION    
  INTEGER gps-only(1), glonass-only(2), gps-and-glonass(3)  

ConstellationTypesBitMap  
Indicates GNSS constellation types supported by a GNSS Receiver Port. The valid bits must be set in order for this attribute to contain valid information. The representation of each bit setting (0 or 1) is indicated below. Bit Field Flag Description --------- ------------------------------------ 0 1 = GPS is supported; 0 = GPS not supported 1 1 = GLONASS is supported; 0 = GLONASS is not supported 2 1 = BEIDOU is supported; 0 = BEIDOU is not supported 3 1 = GALILEO is supported; 0 = GALILEO is not supported 4 1 = SBAS is supported; 0 = SBAS is not supported
TEXTUAL-CONVENTION    
  BITS gps(0), glonass(1), beidou(2), galileo(3), sbas(4)  

InstallationType  
Installation Type of GPS Antenna
TEXTUAL-CONVENTION    
  INTEGER full-sky-view(1), limited-sky-view(2)  

WIFIEncryptionType  
Type of WIFI encryption
TEXTUAL-CONVENTION    
  INTEGER notApplicable(0), wpa-psk(1), wpa2-psk(2), wpa-wpa2-psk(3)  

DHCPType  
DHCP role type
TEXTUAL-CONVENTION    
  INTEGER client(1), server(2)  

CosMappingMode  
EoMpls Cos Mapping mode
TEXTUAL-CONVENTION    
  INTEGER ethernet(1), eompls(2), vxlan(3)  

EthernetPortTrafficModel  
Traffic Model for Ethernet Port.
TEXTUAL-CONVENTION    
  INTEGER accessFlow(1), flowpoint(2)  

CmEthernetAccPortEntry  
SEQUENCE    
  cmEthernetAccPortIndex Integer32
  cmEthernetAccPortIfIndex InterfaceIndex
  cmEthernetAccPortEntityIndex PhysicalIndex
  cmEthernetAccPortAdminState AdminState
  cmEthernetAccPortOperationalState OperationalState
  cmEthernetAccPortSecondaryState SecondaryState
  cmEthernetAccPortMTU Integer32
  cmEthernetAccPortMediaType EthernetMediaType
  cmEthernetAccPortConfigSpeed EthernetPortSpeed
  cmEthernetAccPortNegotiatedSpeed EthernetPortSpeed
  cmEthernetAccPortMDIXType CmEthernetMDIXType
  cmEthernetAccPortJumboFramesEnabled TruthValue
  cmEthernetAccPortSfpVendorName DisplayString
  cmEthernetAccPortSfpPartNumber DisplayString
  cmEthernetAccPortSfpSerialNumber DisplayString
  cmEthernetAccPortSfpDateOfManufacture DateAndTime
  cmEthernetAccPortSfpConnectorValue SfpConnectorValue
  cmEthernetAccPortInitiateDiag CmEthernetDiagAction
  cmEthernetAccPortDiagnosePair1Cond CmDiagCableCondType
  cmEthernetAccPortDiagnosePair2Cond CmDiagCableCondType
  cmEthernetAccPortDiagnosePair3Cond CmDiagCableCondType
  cmEthernetAccPortDiagnosePair4Cond CmDiagCableCondType
  cmEthernetAccPortDiagnoseAutoNegCond CmDiagAutoNegCondType
  cmEthernetAccPortDiagnoseLpbkCond CmDiagLpbkCondType
  cmEthernetAccPortDiagnoseEfmLpbkCond CmDiagEfmOamLpbkCondType
  cmEthernetAccPortDiagnoseResult DisplayString
  cmEthernetAccPortDiagnoseTestStatus CmDiagTestStatus
  cmEthernetAccPortDiagnoseTestTime DateAndTime
  cmEthernetAccPortLoopbackConfig CmLoopbackType
  cmEthernetAccPortLoopbackStatus CmLoopbackType
  cmEthernetAccPortLoopbackTime Integer32
  cmEthernetAccPortLoopbackSwapSADA CmSwapSADAType
  cmEthernetAccPortOuterVlanLoopbackMask INTEGER
  cmEthernetAccPortOuterVlanLoopback1 DisplayString
  cmEthernetAccPortOuterVlanLoopback2 DisplayString
  cmEthernetAccPortOuterVlanLoopback3 DisplayString
  cmEthernetAccPortInnerVlanLoopbackMask INTEGER
  cmEthernetAccPortInnerVlanLoopback1 DisplayString
  cmEthernetAccPortInnerVlanLoopback2 DisplayString
  cmEthernetAccPortInnerVlanLoopback3 DisplayString
  cmEthernetAccPortLinkLossFwdEnabled TruthValue
  cmEthernetAccPortLinkLossFwdSignalType CmLinkLossFwdSignalType
  cmEthernetAccPortLinkLossFwdTriggerTypes CmLinkLossFwdTriggerTypes
  cmEthernetAccPortLinkLossFwdDelay Integer32
  cmEthernetAccPortLinkLossFwdActive TruthValue
  cmEthernetAccPortLinkLossFwdPartnerEnabled TruthValue
  cmEthernetAccPortLinkLossFwdLocalLinkId Integer32
  cmEthernetAccPortLinkLossFwdRemoteLinkIds CmRemoteLinkIds
  cmEthernetAccPortOamId Integer32
  cmEthernetAccPortOamAdminDisposition CmControlProtocolDispType
  cmEthernetAccPortOamDiscoveryState CmOamDiscoveryState
  cmEthernetAccPortOamLocalVarRtrvsEnabled TruthValue
  cmEthernetAccPortOamLocalLinkEventsEnabled TruthValue
  cmEthernetAccPortOamLocalOamLoopbacksSupported TruthValue
  cmEthernetAccPortOamLocalUnidirSupportEnabled TruthValue
  cmEthernetAccPortOamLocalMaxPDUSize Integer32
  cmEthernetAccPortOamLocalMode CmOamMode
  cmEthernetAccPortOamRemoteMacAddress MacAddress
  cmEthernetAccPortOamRemoteVarRtrvsEnabled TruthValue
  cmEthernetAccPortOamRemoteLinkEventsEnabled TruthValue
  cmEthernetAccPortOamRemoteOamLoopbacksSupported TruthValue
  cmEthernetAccPortOamRemoteUnidirSupportEnabled TruthValue
  cmEthernetAccPortOamRemoteMaxPDUSize Integer32
  cmEthernetAccPortOamRemoteMode CmOamMode
  cmEthernetAccPortMode CmEthernetSvcPortMode
  cmEthernetAccPortSvcType CmEthernetSvcType
  cmEthernetAccPortRxPauseDisposition CmControlProtocolDispType
  cmEthernetAccPortTxPauseEnabled TruthValue
  cmEthernetAccPortAfpType CmAfpType
  cmEthernetAccPortMDIXStatus CmEthernetMDIXType
  cmEthernetAccPortSfpReach Integer32
  cmEthernetAccPortSfpLaserWaveLength Integer32
  cmEthernetAccPortSfpMediaType SfpMediaType
  cmEthernetAccPortOamEnabled TruthValue
  cmEthernetAccPortOamAdminState CmOamAdminState
  cmEthernetAccPortShapingEnabled TruthValue
  cmEthernetAccPortShapedSpeedLo Unsigned32
  cmEthernetAccPortShapedSpeedHi Unsigned32
  cmEthernetAccPortQinQEtherType Unsigned32
  cmEthernetAccPortRxPauseEnabled TruthValue
  cmEthernetAccPortAutoDiagEnabled TruthValue
  cmEthernetAccPortLinkLossFwdTxActionType CmLinkLossFwdTxActionType
  cmEthernetAccPortLinkLossFwdRxRLDLinkIds CmRemoteLinkIds
  cmEthernetAccPortN2AVlanTrunkingEnabled TruthValue
  cmEthernetAccPortA2NPushPVIDEnabled TruthValue
  cmEthernetAccPortN2APopPVIDEnabled TruthValue
  cmEthernetAccPortPortVlanId VlanId
  cmEthernetAccPortPortVlanPriority VlanPriority
  cmEthernetAccPortPrioMapMode PriorityMapMode
  cmEthernetAccPortSyncEEnabled TruthValue
  cmEthernetAccPortQLModeEnabled TruthValue
  cmEthernetAccPortExpectedQL SSMQualityLevel
  cmEthernetAccPortAssumedQL SSMQualityLevel
  cmEthernetAccPortReceivedQL SSMQualityLevel
  cmEthernetAccPortTransmitQL SSMQualityLevel
  cmEthernetAccPortDeiEnable TruthValue
  cmEthernetAccPortPcpDEEncType PcpDEEncType
  cmEthernetAccPortPcpDEPairsAction PcpDEPairsAction
  cmEthernetAccPortSSMRemoteMacAddress MacAddress
  cmEthernetAccPortXgePhyType XgePhyType
  cmEthernetAccPortLoopbackSourceMacControlEnabled TruthValue
  cmEthernetAccPortLoopbackDestMacControlEnabled TruthValue
  cmEthernetAccPortLoopbackSourceMacAddress MacAddress
  cmEthernetAccPortLoopbackDestMacAddress MacAddress
  cmEthernetAccPortLoopbackBlockingEnabled TruthValue
  cmEthernetAccPortRxDeiAction RxDeiAction
  cmEthernetAccPortTxDeiAction TxDeiAction
  cmEthernetAccPortRxDeiOuterTagType DeiOuterTagType
  cmEthernetAccPortTxDeiOuterTagType DeiOuterTagType
  cmEthernetAccPortLaserWDMChannel SfpChannelIdentifier
  cmEthernetAccPortLaserIsTunable TruthValue
  cmEthernetAccPortLaserFrequency Unsigned32
  cmEthernetAccPortMediaTypeAutoSelected EthernetMediaType
  cmEthernetAccPortLowLatencyQueuingEnabled TruthValue
  cmEthernetAccPortA2nSwapPriorityVIDEnabled TruthValue
  cmEthernetAccPortN2aSwapPriorityVIDEnabled TruthValue
  cmEthernetAccPortSwapPriorityVID VlanId
  cmEthernetAccPortDiagnosticMacAddress MacAddress
  cmEthernetAccPortIngressCOSPriority VlanTagType
  cmEthernetAccPortDefaultCOS Integer32
  cmEthernetAccPortTrafficModel EthernetPortTrafficModel

CmEthernetAccPortCpdEntry  
SEQUENCE    
  cmEthernetAccPortCpdIndex Integer32
  cmEthernetAccPortCpdFilterType CmControlProtocolFilterType
  cmEthernetAccPortCpdFilterDescr DisplayString
  cmEthernetAccPortCpdDispType CmControlProtocolDispType
  cmEthernetAccPortCpdMacAddressMatch MacAddress
  cmEthernetAccPortCpdMacAddressMask MacAddress
  cmEthernetAccPortCpdEthertype Integer32
  cmEthernetAccPortCpdEthertypeMask Integer32
  cmEthernetAccPortCpdSubtype Integer32
  cmEthernetAccPortCpdSubtypeMask Integer32

CmEthernetAccPortClbEntry  
SEQUENCE    
  cmEthernetAccPortClbIndex Integer32
  cmEthernetAccPortClbEnabled TruthValue
  cmEthernetAccPortClbLength DisplayString
  cmEthernetAccPortClbDescr DisplayString

CmFlowEntry  
SEQUENCE    
  cmFlowIndex Integer32
  cmFlowCircuitName DisplayString
  cmFlowAdminState AdminState
  cmFlowOperationalState OperationalState
  cmFlowSecondaryState SecondaryState
  cmFlowType CmFlowType
  cmFlowMultiCOS TruthValue
  cmFlowA2NCIR Unsigned32
  cmFlowA2NEIR Unsigned32
  cmFlowN2ARateLimitingEnabled TruthValue
  cmFlowN2ACIR Unsigned32
  cmFlowN2AEIR Unsigned32
  cmFlowStorageType StorageType
  cmFlowRowStatus RowStatus
  cmFlowTrafficType FlowTrafficType
  cmFlowCOS Integer32
  cmFlowVlanMemberList DisplayString
  cmFlowAction FlowVlanActionType
  cmFlowActionVlan DisplayString
  cmFlowUntaggedMemberEnabled TruthValue
  cmFlowA2NCIRHi Unsigned32
  cmFlowA2NEIRHi Unsigned32
  cmFlowN2ACIRHi Unsigned32
  cmFlowN2AEIRHi Unsigned32
  cmFlowHCOSMgmtEnabled TruthValue
  cmFlowGuaranteedA2NBandwidthLo Unsigned32
  cmFlowGuaranteedA2NBandwidthHi Unsigned32
  cmFlowMaximumA2NBandwidthLo Unsigned32
  cmFlowMaximumA2NBandwidthHi Unsigned32
  cmFlowCTagControl FlowTagControl
  cmFlowCTagVlanId VlanId
  cmFlowCTagVlanPriority VlanPriority
  cmFlowCTagMatchRxPrio TruthValue
  cmFlowSTagControl FlowTagControl
  cmFlowSTagVlanId VlanId
  cmFlowSTagVlanPriority VlanPriority
  cmFlowOuterTagPrioEnabled TruthValue
  cmFlowN2ACOSPriorityTagType VlanTagType
  cmFlowESFramesLossThreshold Integer32
  cmFlowSESFramesLossThresholdRatio Integer32
  cmFlowPolicingEnabled TruthValue
  cmFlowPreserveSTagProperties TruthValue
  cmFlowInnerTagPrioEnabled TruthValue
  cmFlowN2AOuterTagPrioEnabled TruthValue
  cmFlowA2NShapingType ShapingType
  cmFlowN2AShapingType ShapingType
  cmFlowSTagMatchRxPrio TruthValue
  cmFlowAutoBandwidthConfigEnabled TruthValue
  cmFlowPort1 VariablePointer
  cmFlowPort2 VariablePointer
  cmFlowPolicingControl PolicingControl
  cmFlowAutoCIRPercentage Integer32
  cmFlowLoopAvoidanceObject VariablePointer
  cmFlowConfigType FlowConfigType
  cmFlowN2NForwardingEnabled TruthValue
  cmFlowA2NMulticastRateLimitControl TruthValue
  cmFlowA2NMulticastRateLimitLo Unsigned32
  cmFlowA2NMulticastRateLimitHi Unsigned32
  cmFlowA2NBroadcastRateLimitControl TruthValue
  cmFlowA2NBroadcastRateLimitLo Unsigned32
  cmFlowA2NBroadcastRateLimitHi Unsigned32
  cmFlowA2NCombinedRateLimitControl TruthValue
  cmFlowA2NCombinedRateLimitLo Unsigned32
  cmFlowA2NCombinedRateLimitHi Unsigned32
  cmFlowRefPrioMapProfile VariablePointer
  cmFlowRefEoMplsPwObject VariablePointer
  cmFlowRefN2APrioMapProfile VariablePointer
  cmFlowSecureBlockingEnabled TruthValue
  cmFlowRefConnectGuardFlowList DisplayString
  cmFlowSecureStateList DisplayString

CmFlowCpdEntry  
SEQUENCE    
  cmFlowCpdIndex Integer32
  cmFlowCpdFilterType CmControlProtocolFilterType
  cmFlowCpdFilterDescr DisplayString
  cmFlowCpdDispType CmControlProtocolDispType
  cmFlowCpdMacAddressMatch MacAddress
  cmFlowCpdMacAddressMask MacAddress
  cmFlowCpdEthertype Integer32
  cmFlowCpdEthertypeMask Integer32
  cmFlowCpdSubtype Integer32
  cmFlowCpdSubtypeMask Integer32

CmQosShaperEntry  
SEQUENCE    
  cmQosShaperTypeIndex Integer32
  cmQosShaperIndex Integer32
  cmQosShaperDirection TrafficDirection
  cmQosShaperAdminState AdminState
  cmQosShaperOperationalState OperationalState
  cmQosShaperSecondaryState SecondaryState
  cmQosShaperCIR Unsigned32
  cmQosShaperCBS Unsigned32
  cmQosShaperEIR Unsigned32
  cmQosShaperEBS Unsigned32
  cmQosShaperBufferSize Unsigned32
  cmQosShaperStorageType StorageType
  cmQosShaperRowStatus RowStatus
  cmQosShaperCOS Integer32
  cmQosShaperCIRHi Unsigned32
  cmQosShaperEIRHi Unsigned32
  cmQosShaperSoamCIRLo Unsigned32
  cmQosShaperSoamCIRHi Unsigned32
  cmQosShaperSoamEIRLo Unsigned32
  cmQosShaperSoamEIRHi Unsigned32
  cmQosShaperWredGreenMinQueueThreshold Unsigned32
  cmQosShaperWredGreenMaxQueueThreshold Unsigned32
  cmQosShaperWredGreenDropProbability Unsigned32
  cmQosShaperWredYellowMinQueueThreshold Unsigned32
  cmQosShaperWredYellowMaxQueueThreshold Unsigned32
  cmQosShaperWredYellowDropProbability Unsigned32

CmEthernetNetPortEntry  
SEQUENCE    
  cmEthernetNetPortIndex Integer32
  cmEthernetNetPortIfIndex InterfaceIndex
  cmEthernetNetPortEntityIndex PhysicalIndex
  cmEthernetNetPortAdminState AdminState
  cmEthernetNetPortOperationalState OperationalState
  cmEthernetNetPortSecondaryState SecondaryState
  cmEthernetNetPortMTU Integer32
  cmEthernetNetPortMediaType EthernetMediaType
  cmEthernetNetPortConfigSpeed EthernetPortSpeed
  cmEthernetNetPortNegotiatedSpeed EthernetPortSpeed
  cmEthernetNetPortMDIXType CmEthernetMDIXType
  cmEthernetNetPortJumboFramesEnabled TruthValue
  cmEthernetNetPortSfpVendorName DisplayString
  cmEthernetNetPortSfpPartNumber DisplayString
  cmEthernetNetPortSfpSerialNumber DisplayString
  cmEthernetNetPortSfpDateOfManufacture DateAndTime
  cmEthernetNetPortSfpConnectorValue SfpConnectorValue
  cmEthernetNetPortInitiateDiag CmEthernetDiagAction
  cmEthernetNetPortDiagnosePair1Cond CmDiagCableCondType
  cmEthernetNetPortDiagnosePair2Cond CmDiagCableCondType
  cmEthernetNetPortDiagnosePair3Cond CmDiagCableCondType
  cmEthernetNetPortDiagnosePair4Cond CmDiagCableCondType
  cmEthernetNetPortDiagnoseAutoNegCond CmDiagAutoNegCondType
  cmEthernetNetPortDiagnoseLpbkCond CmDiagLpbkCondType
  cmEthernetNetPortDiagnoseEfmLpbkCond CmDiagEfmOamLpbkCondType
  cmEthernetNetPortDiagnoseResult DisplayString
  cmEthernetNetPortDiagnoseTestStatus CmDiagTestStatus
  cmEthernetNetPortDiagnoseTestTime DateAndTime
  cmEthernetNetPortLoopbackConfig CmLoopbackType
  cmEthernetNetPortLoopbackStatus CmLoopbackType
  cmEthernetNetPortLoopbackTime Integer32
  cmEthernetNetPortLoopbackSwapSADA CmSwapSADAType
  cmEthernetNetPortOuterVlanLoopbackMask INTEGER
  cmEthernetNetPortOuterVlanLoopback1 DisplayString
  cmEthernetNetPortOuterVlanLoopback2 DisplayString
  cmEthernetNetPortOuterVlanLoopback3 DisplayString
  cmEthernetNetPortInnerVlanLoopbackMask INTEGER
  cmEthernetNetPortInnerVlanLoopback1 DisplayString
  cmEthernetNetPortInnerVlanLoopback2 DisplayString
  cmEthernetNetPortInnerVlanLoopback3 DisplayString
  cmEthernetNetPortLinkLossFwdEnabled TruthValue
  cmEthernetNetPortLinkLossFwdSignalType CmLinkLossFwdSignalType
  cmEthernetNetPortLinkLossFwdTriggerTypes CmLinkLossFwdTriggerTypes
  cmEthernetNetPortLinkLossFwdDelay Integer32
  cmEthernetNetPortLinkLossFwdActive TruthValue
  cmEthernetNetPortLinkLossFwdPartnerEnabled TruthValue
  cmEthernetNetPortLinkLossFwdLocalLinkId Integer32
  cmEthernetNetPortLinkLossFwdRemoteLinkIds CmRemoteLinkIds
  cmEthernetNetPortOamId Integer32
  cmEthernetNetPortOamAdminDisposition CmControlProtocolDispType
  cmEthernetNetPortOamDiscoveryState CmOamDiscoveryState
  cmEthernetNetPortOamLocalVarRtrvsEnabled TruthValue
  cmEthernetNetPortOamLocalLinkEventsEnabled TruthValue
  cmEthernetNetPortOamLocalOamLoopbacksSupported TruthValue
  cmEthernetNetPortOamLocalUnidirSupportEnabled TruthValue
  cmEthernetNetPortOamLocalMaxPDUSize Integer32
  cmEthernetNetPortOamLocalMode CmOamMode
  cmEthernetNetPortOamRemoteMacAddress MacAddress
  cmEthernetNetPortOamRemoteVarRtrvsEnabled TruthValue
  cmEthernetNetPortOamRemoteLinkEventsEnabled TruthValue
  cmEthernetNetPortOamRemoteOamLoopbacksSupported TruthValue
  cmEthernetNetPortOamRemoteUnidirSupportEnabled TruthValue
  cmEthernetNetPortOamRemoteMaxPDUSize Integer32
  cmEthernetNetPortOamRemoteMode CmOamMode
  cmEthernetNetPortRxPauseDisposition CmControlProtocolDispType
  cmEthernetNetPortTxPauseEnabled TruthValue
  cmEthernetNetPortAfpType CmAfpType
  cmEthernetNetPortMDIXStatus CmEthernetMDIXType
  cmEthernetNetPortSfpReach Integer32
  cmEthernetNetPortSfpLaserWaveLength Integer32
  cmEthernetNetPortSfpMediaType SfpMediaType
  cmEthernetNetPortOamEnabled TruthValue
  cmEthernetNetPortOamAdminState CmOamAdminState
  cmEthernetNetPortShapingEnabled TruthValue
  cmEthernetNetPortShapedSpeedLo Unsigned32
  cmEthernetNetPortShapedSpeedHi Unsigned32
  cmEthernetNetPortQinQEtherType Unsigned32
  cmEthernetNetPortLinkLossFwdTxActionType CmLinkLossFwdTxActionType
  cmEthernetNetPortLinkLossFwdRxRLDLinkIds CmRemoteLinkIds
  cmEthernetNetPortAutoDiagEnabled TruthValue
  cmEthernetNetPortSyncEEnabled TruthValue
  cmEthernetNetPortQLModeEnabled TruthValue
  cmEthernetNetPortExpectedQL SSMQualityLevel
  cmEthernetNetPortAssumedQL SSMQualityLevel
  cmEthernetNetPortReceivedQL SSMQualityLevel
  cmEthernetNetPortTransmitQL SSMQualityLevel
  cmEthernetNetPortPrioMapMode PriorityMapMode
  cmEthernetNetPortDeiEnable TruthValue
  cmEthernetNetPortPcpDEEncType PcpDEEncType
  cmEthernetNetPortPcpDEPairsAction PcpDEPairsAction
  cmEthernetNetPortSSMRemoteMacAddress MacAddress
  cmEthernetNetPortXgePhyType XgePhyType
  cmEthernetNetPortLoopbackSourceMacControlEnabled TruthValue
  cmEthernetNetPortLoopbackDestMacControlEnabled TruthValue
  cmEthernetNetPortLoopbackSourceMacAddress MacAddress
  cmEthernetNetPortLoopbackDestMacAddress MacAddress
  cmEthernetNetPortLoopbackBlockingEnabled TruthValue
  cmEthernetNetPortRxDeiAction RxDeiAction
  cmEthernetNetPortTxDeiAction TxDeiAction
  cmEthernetNetPortRxDeiOuterTagType DeiOuterTagType
  cmEthernetNetPortTxDeiOuterTagType DeiOuterTagType
  cmEthernetNetPortLaserWDMChannel SfpChannelIdentifier
  cmEthernetNetPortLaserIsTunable TruthValue
  cmEthernetNetPortLaserFrequency Unsigned32
  cmEthernetNetPortMediaTypeAutoSelected EthernetMediaType
  cmEthernetNetPortLowLatencyQueuingEnabled TruthValue
  cmEthernetNetPortDiagnosticMacAddress MacAddress
  cmEthernetNetPortIngressCOSPriority VlanTagType
  cmEthernetNetPortDefaultCOS Integer32
  cmEthernetNetPortTrafficModel EthernetPortTrafficModel

CmEthernetNetPortCpdEntry  
SEQUENCE    
  cmEthernetNetPortCpdIndex Integer32
  cmEthernetNetPortCpdFilterType CmControlProtocolFilterType
  cmEthernetNetPortCpdFilterDescr DisplayString
  cmEthernetNetPortCpdDispType CmControlProtocolDispType
  cmEthernetNetPortCpdMacAddressMatch MacAddress
  cmEthernetNetPortCpdMacAddressMask MacAddress
  cmEthernetNetPortCpdEthertype Integer32
  cmEthernetNetPortCpdEthertypeMask Integer32
  cmEthernetNetPortCpdSubtype Integer32
  cmEthernetNetPortCpdSubtypeMask Integer32

CmEthernetMgmtPortEntry  
SEQUENCE    
  cmEthernetMgmtPortIndex Integer32
  cmEthernetMgmtPortEntityIndex PhysicalIndex
  cmEthernetMgmtPortAdminState AdminState
  cmEthernetMgmtPortOperationalState OperationalState
  cmEthernetMgmtPortSecondaryState SecondaryState
  cmEthernetMgmtPortMTU Integer32
  cmEthernetMgmtPortConfigSpeed EthernetPortSpeed
  cmEthernetMgmtPortNegotiatedSpeed EthernetPortSpeed
  cmEthernetMgmtPortMDIXType CmEthernetMDIXType
  cmEthernetMgmtPortMDIXStatus CmEthernetMDIXType
  cmEthernetMgmtPortMediaType EthernetMediaType

CmPrioMapEntry  
SEQUENCE    
  cmPrioMapIndex Integer32
  cmPrioMapInPriority Integer32
  cmPrioMapXTagControl PrioMapControlType
  cmPrioMapXTagPriority VlanPriority
  cmPrioMapCOS Integer32
  cmPrioMapOuterTagPriority VlanPriority
  cmPrioMapInnerTagPriority VlanPriority

CmQosFlowPolicerEntry  
SEQUENCE    
  cmQosFlowPolicerTypeIndex Integer32
  cmQosFlowPolicerIndex Integer32
  cmQosFlowPolicerDirection TrafficDirection
  cmQosFlowPolicerAdminState AdminState
  cmQosFlowPolicerOperationalState OperationalState
  cmQosFlowPolicerSecondaryState SecondaryState
  cmQosFlowPolicerCIRLo Unsigned32
  cmQosFlowPolicerCIRHi Unsigned32
  cmQosFlowPolicerEIRLo Unsigned32
  cmQosFlowPolicerEIRHi Unsigned32
  cmQosFlowPolicerCBS Integer32
  cmQosFlowPolicerEBS Integer32
  cmQosFlowPolicerAlgorithm PolicerAlgorithmType
  cmQosFlowPolicerColorMode PolicerColorMode
  cmQosFlowPolicerColorMarkingFlag TruthValue
  cmQosFlowPolicerCouplingFlag TruthValue
  cmQosFlowPolicerAssociatedShaper VariablePointer
  cmQosFlowPolicerStorageType StorageType
  cmQosFlowPolicerRowStatus RowStatus

CmAccPortQosShaperEntry  
SEQUENCE    
  cmAccPortQosShaperIndex Integer32
  cmAccPortQosShaperDirection TrafficDirection
  cmAccPortQosShaperAdminState AdminState
  cmAccPortQosShaperOperationalState OperationalState
  cmAccPortQosShaperSecondaryState SecondaryState
  cmAccPortQosShaperCIRLo Unsigned32
  cmAccPortQosShaperCIRHi Unsigned32
  cmAccPortQosShaperEIRLo Unsigned32
  cmAccPortQosShaperEIRHi Unsigned32
  cmAccPortQosShaperCBS Unsigned32
  cmAccPortQosShaperEBS Unsigned32
  cmAccPortQosShaperBufferSize Unsigned32
  cmAccPortQosShaperCOS Integer32
  cmAccPortQosShaperSoamCIRLo Unsigned32
  cmAccPortQosShaperSoamCIRHi Unsigned32
  cmAccPortQosShaperSoamEIRLo Unsigned32
  cmAccPortQosShaperSoamEIRHi Unsigned32
  cmAccPortQosShaperWredGreenMinQueueThreshold Unsigned32
  cmAccPortQosShaperWredGreenMaxQueueThreshold Unsigned32
  cmAccPortQosShaperWredGreenDropProbability Unsigned32
  cmAccPortQosShaperWredYellowMinQueueThreshold Unsigned32
  cmAccPortQosShaperWredYellowMaxQueueThreshold Unsigned32
  cmAccPortQosShaperWredYellowDropProbability Unsigned32

CmEthernetAccPortCpdV2Entry  
SEQUENCE    
  cmEthernetAccPortCpdV2Index Integer32
  cmEthernetAccPortCpdV2CiscoGroupDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2IslDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2PagpDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2UdldDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2CdpDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2VtpDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2DtpDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2PvstpPlusDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2UplinkFastDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2VlanBridgeDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2L2PTDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2BridgeGroupDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2BPDUDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2PauseDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2LACPDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2LACPMarkerDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2EfmOamDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2SSMDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2PortAuthenDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2BridgeReservedDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2LANBridgesDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2GARPGroupDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2GMRPDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2GVRPDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2GARPDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2LLDPDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2ELMIDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2L2PTTunnelMac MacAddress
  cmEthernetAccPortCpdV2Mac00DispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac01DispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac02DispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac03DispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac04DispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac05DispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac06DispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac07DispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac08DispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac09DispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac0ADispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac0BDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac0CDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac0DDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac0EDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2Mac0FDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2NearestLLDPDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2NonTpmrLLDPDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2CustomerLLDPDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2PtpUntaggedDispType CmControlProtocolDispType
  cmEthernetAccPortCpdV2PtpTaggedDispType CmControlProtocolDispType

CmFlowCpdV2Entry  
SEQUENCE    
  cmFlowCpdV2Index Integer32
  cmFlowCpdV2CiscoGroupDispType CmControlProtocolDispType
  cmFlowCpdV2IslDispType CmControlProtocolDispType
  cmFlowCpdV2PagpDispType CmControlProtocolDispType
  cmFlowCpdV2UdldDispType CmControlProtocolDispType
  cmFlowCpdV2CdpDispType CmControlProtocolDispType
  cmFlowCpdV2VtpDispType CmControlProtocolDispType
  cmFlowCpdV2DtpDispType CmControlProtocolDispType
  cmFlowCpdV2PvstpPlusDispType CmControlProtocolDispType
  cmFlowCpdV2UplinkFastDispType CmControlProtocolDispType
  cmFlowCpdV2VlanBridgeDispType CmControlProtocolDispType
  cmFlowCpdV2L2PTDispType CmControlProtocolDispType
  cmFlowCpdV2BridgeGroupDispType CmControlProtocolDispType
  cmFlowCpdV2BPDUDispType CmControlProtocolDispType
  cmFlowCpdV2PauseDispType CmControlProtocolDispType
  cmFlowCpdV2LACPDispType CmControlProtocolDispType
  cmFlowCpdV2LACPMarkerDispType CmControlProtocolDispType
  cmFlowCpdV2EfmOamDispType CmControlProtocolDispType
  cmFlowCpdV2SSMDispType CmControlProtocolDispType
  cmFlowCpdV2PortAuthenDispType CmControlProtocolDispType
  cmFlowCpdV2BridgeReservedDispType CmControlProtocolDispType
  cmFlowCpdV2LANBridgesDispType CmControlProtocolDispType
  cmFlowCpdV2GARPGroupDispType CmControlProtocolDispType
  cmFlowCpdV2GMRPDispType CmControlProtocolDispType
  cmFlowCpdV2GVRPDispType CmControlProtocolDispType
  cmFlowCpdV2GARPDispType CmControlProtocolDispType
  cmFlowCpdV2ActiveControlProtocols CmActiveControlProtocolsType
  cmFlowCpdV2LLDPDispType CmControlProtocolDispType
  cmFlowCpdV2ELMIDispType CmControlProtocolDispType
  cmFlowCpdV2Mac00DispType CmControlProtocolDispType
  cmFlowCpdV2Mac01DispType CmControlProtocolDispType
  cmFlowCpdV2Mac02DispType CmControlProtocolDispType
  cmFlowCpdV2Mac03DispType CmControlProtocolDispType
  cmFlowCpdV2Mac04DispType CmControlProtocolDispType
  cmFlowCpdV2Mac05DispType CmControlProtocolDispType
  cmFlowCpdV2Mac06DispType CmControlProtocolDispType
  cmFlowCpdV2Mac07DispType CmControlProtocolDispType
  cmFlowCpdV2Mac08DispType CmControlProtocolDispType
  cmFlowCpdV2Mac09DispType CmControlProtocolDispType
  cmFlowCpdV2Mac0ADispType CmControlProtocolDispType
  cmFlowCpdV2Mac0BDispType CmControlProtocolDispType
  cmFlowCpdV2Mac0CDispType CmControlProtocolDispType
  cmFlowCpdV2Mac0DDispType CmControlProtocolDispType
  cmFlowCpdV2Mac0EDispType CmControlProtocolDispType
  cmFlowCpdV2Mac0FDispType CmControlProtocolDispType
  cmFlowCpdV2NearestLLDPDispType CmControlProtocolDispType
  cmFlowCpdV2NonTpmrLLDPDispType CmControlProtocolDispType
  cmFlowCpdV2CustomerLLDPDispType CmControlProtocolDispType

CmEthernetNetPortCpdV2Entry  
SEQUENCE    
  cmEthernetNetPortCpdV2Index Integer32
  cmEthernetNetPortCpdV2CiscoGroupDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2IslDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2PagpDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2UdldDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2CdpDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2VtpDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2DtpDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2PvstpPlusDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2UplinkFastDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2VlanBridgeDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2L2PTDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2BridgeGroupDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2BPDUDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2PauseDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2LACPDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2LACPMarkerDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2EfmOamDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2SSMDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2PortAuthenDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2BridgeReservedDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2LANBridgesDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2GARPGroupDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2GMRPDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2GVRPDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2GARPDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2LLDPDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2ELMIDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2L2PTTunnelMac MacAddress
  cmEthernetNetPortCpdV2Mac00DispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac01DispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac02DispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac03DispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac04DispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac05DispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac06DispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac07DispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac08DispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac09DispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac0ADispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac0BDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac0CDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac0DDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac0EDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2Mac0FDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2NearestLLDPDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2NonTpmrLLDPDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2CustomerLLDPDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2PtpUntaggedDispType CmControlProtocolDispType
  cmEthernetNetPortCpdV2PtpTaggedDispType CmControlProtocolDispType

BitsPortEntry  
SEQUENCE    
  bitsPortTypeIndex Integer32
  bitsPortIndex Integer32
  bitsPortIfIndex InterfaceIndex
  bitsPortEntityIndex PhysicalIndex
  bitsPortAdminState AdminState
  bitsPortOperationalState OperationalState
  bitsPortSecondaryState SecondaryState
  bitsPortType BitsPortType
  bitsPortLineType BitsPortLineType
  bitsPortLineCode BitsPortLineCode
  bitsPortFrameFormat BitsFrameFormat
  bitsPortSaBitDesignation SaBitDesignation
  bitsPortQLModeEnabled TruthValue
  bitsPortExpectedQL SSMQualityLevel
  bitsPortAssumedQL SSMQualityLevel
  bitsPortReceivedQL SSMQualityLevel
  bitsPortTransmitQL SSMQualityLevel
  bitsPortSquelchQL SSMQualityLevel
  bitsPortLineBuildOut LineBuildOut
  bitsPortImpedance BitsPortImpedanceMode

IEEE1588EthernetPortEntry  
SEQUENCE    
  ieee1588EthernetPortIndex Integer32
  ieee1588EthernetPortIfIndex InterfaceIndex
  ieee1588EthernetPortEntityIndex PhysicalIndex
  ieee1588EthernetPortAdminState AdminState
  ieee1588EthernetPortOperationalState OperationalState
  ieee1588EthernetPortSecondaryState SecondaryState
  ieee1588EthernetPortMTU Integer32
  ieee1588EthernetPortMediaType EthernetMediaType
  ieee1588EthernetPortConfigSpeed EthernetPortSpeed
  ieee1588EthernetPortNegotiatedSpeed EthernetPortSpeed
  ieee1588EthernetPortMDIXType CmEthernetMDIXType

GPS10MHzPortEntry  
SEQUENCE    
  gps10MHzPortIndex Integer32
  gps10MHzPortIfIndex InterfaceIndex
  gps10MHzPortEntityIndex PhysicalIndex
  gps10MHzPortAdminState AdminState
  gps10MHzPortOperationalState OperationalState
  gps10MHzPortSecondaryState SecondaryState
  gps10MHzPortSignalDirection SignalDirectionType
  gps10MHzPortSquelchControl SquelchControl
  gps10MHzPortSquelchQL SSMQualityLevel
  gps10MHzPortFrequencySource VariablePointer
  gps10MHzPortClockClass Unsigned32
  gps10MHzPortClockAccuracy Unsigned32
  gps10MHzPortTimeSource TimeSource
  gps10MHzPortAssumedQL SSMQualityLevel
  gps10MHzPortAlias DisplayString

CmEthernetNetPortClbEntry  
SEQUENCE    
  cmEthernetNetPortClbIndex Integer32
  cmEthernetNetPortClbEnabled TruthValue
  cmEthernetNetPortClbLength DisplayString
  cmEthernetNetPortClbDescr DisplayString

CmNetPortPrioMapEntry  
SEQUENCE    
  cmNetPortPrioMapIndex Integer32
  cmNetPortPrioMapInPriority Integer32
  cmNetPortPrioMapCOS Integer32
  cmNetPortPrioMapOuterTagPriority VlanPriority

CmAccPortPcpDEEncEntry  
SEQUENCE    
  cmAccPortPcpDEEncIndex Integer32
  cmAccPortPcpDEEncInPriority VlanPriority
  cmAccPortPcpDEEncDropIneligiblePrio VlanPriority
  cmAccPortPcpDEEncDropEligiblePrio VlanPriority

CmAccPortPcpDEDecEntry  
SEQUENCE    
  cmAccPortPcpDEDecIndex Integer32
  cmAccPortPcpDEDecInPriority VlanPriority
  cmAccPortPcpDEDecOutPriority VlanPriority
  cmAccPortPcpDEDecDropEligible TruthValue

CmAccPortPcpDEPairEntry  
SEQUENCE    
  cmAccPortPcpDEPairIndex Integer32
  cmAccPortPcpDEDropIneligiblePrio VlanPriority
  cmAccPortPcpDEDropEligiblePrio VlanPriority

CmNetPortPcpDEEncEntry  
SEQUENCE    
  cmNetPortPcpDEEncIndex Integer32
  cmNetPortPcpDEEncInPriority VlanPriority
  cmNetPortPcpDEEncDropIneligiblePrio VlanPriority
  cmNetPortPcpDEEncDropEligiblePrio VlanPriority

CmNetPortPcpDEDecEntry  
SEQUENCE    
  cmNetPortPcpDEDecIndex Integer32
  cmNetPortPcpDEDecInPriority VlanPriority
  cmNetPortPcpDEDecOutPriority VlanPriority
  cmNetPortPcpDEDecDropEligible TruthValue

CmNetPortPcpDEPairEntry  
SEQUENCE    
  cmNetPortPcpDEPairIndex Integer32
  cmNetPortPcpDEDropIneligiblePrio VlanPriority
  cmNetPortPcpDEDropEligiblePrio VlanPriority

CmEthernetTrafficPortEntry  
SEQUENCE    
  cmEthernetTrafficPortIndex Integer32
  cmEthernetTrafficPortIfIndex InterfaceIndex
  cmEthernetTrafficPortEntityIndex PhysicalIndex
  cmEthernetTrafficPortAdminState AdminState
  cmEthernetTrafficPortOperationalState OperationalState
  cmEthernetTrafficPortSecondaryState SecondaryState
  cmEthernetTrafficPortMTU Integer32
  cmEthernetTrafficPortMediaType EthernetMediaType
  cmEthernetTrafficPortConfigSpeed EthernetPortSpeed
  cmEthernetTrafficPortNegotiatedSpeed EthernetPortSpeed
  cmEthernetTrafficPortMDIXType CmEthernetMDIXType
  cmEthernetTrafficPortMDIXStatus CmEthernetMDIXType
  cmEthernetTrafficPortSfpVendorName DisplayString
  cmEthernetTrafficPortSfpPartNumber DisplayString
  cmEthernetTrafficPortSfpSerialNumber DisplayString
  cmEthernetTrafficPortSfpDateOfManufacture DateAndTime
  cmEthernetTrafficPortSfpConnectorValue SfpConnectorValue
  cmEthernetTrafficPortSfpLinkLength Integer32
  cmEthernetTrafficPortSfpLaserWaveLength Integer32
  cmEthernetTrafficPortSfpMediaType SfpMediaType
  cmEthernetTrafficPortLoopbackConfig CmLoopbackType
  cmEthernetTrafficPortLoopbackStatus CmLoopbackType
  cmEthernetTrafficPortLoopbackTime Integer32
  cmEthernetTrafficPortLoopbackSwapSADA CmSwapSADAType
  cmEthernetTrafficPortOuterVlanLoopbackMask INTEGER
  cmEthernetTrafficPortOuterVlanLoopback1 DisplayString
  cmEthernetTrafficPortOuterVlanLoopback2 DisplayString
  cmEthernetTrafficPortOuterVlanLoopback3 DisplayString
  cmEthernetTrafficPortLinkLossFwdEnabled TruthValue
  cmEthernetTrafficPortLinkLossFwdSignalType CmLinkLossFwdSignalType
  cmEthernetTrafficPortLinkLossFwdTriggerTypes CmLinkLossFwdTriggerTypes
  cmEthernetTrafficPortLinkLossFwdDelay Integer32
  cmEthernetTrafficPortLinkLossFwdActive TruthValue
  cmEthernetTrafficPortLinkLossFwdPartnerEnabled TruthValue
  cmEthernetTrafficPortLinkLossFwdLocalLinkId Integer32
  cmEthernetTrafficPortLinkLossFwdRemoteLinkIds DisplayString
  cmEthernetTrafficPortLinkLossFwdTxActionType CmLinkLossFwdTxActionType
  cmEthernetTrafficPortLinkLossFwdRxRLDLinkIds DisplayString
  cmEthernetTrafficPortOamId Integer32
  cmEthernetTrafficPortOamDiscoveryState CmOamDiscoveryState
  cmEthernetTrafficPortOamLocalVarRtrvsEnabled TruthValue
  cmEthernetTrafficPortOamLocalLinkEventsEnabled TruthValue
  cmEthernetTrafficPortOamLocalOamLoopbacksSupported TruthValue
  cmEthernetTrafficPortOamLocalUnidirSupportEnabled TruthValue
  cmEthernetTrafficPortOamLocalMaxPDUSize Integer32
  cmEthernetTrafficPortOamLocalMode CmOamMode
  cmEthernetTrafficPortOamRemoteMacAddress MacAddress
  cmEthernetTrafficPortOamRemoteVarRtrvsEnabled TruthValue
  cmEthernetTrafficPortOamRemoteLinkEventsEnabled TruthValue
  cmEthernetTrafficPortOamRemoteOamLoopbacksSupported TruthValue
  cmEthernetTrafficPortOamRemoteUnidirSupportEnabled TruthValue
  cmEthernetTrafficPortOamRemoteMaxPDUSize Integer32
  cmEthernetTrafficPortOamRemoteMode CmOamMode
  cmEthernetTrafficPortOamEnabled TruthValue
  cmEthernetTrafficPortOamAdminState CmOamAdminState
  cmEthernetTrafficPortSvcType CmEthernetTrafficSvcType
  cmEthernetTrafficPortRxPauseEnabled TruthValue
  cmEthernetTrafficPortTxPauseEnabled TruthValue
  cmEthernetTrafficPortAfpType CmAfpType
  cmEthernetTrafficPortShapingEnabled TruthValue
  cmEthernetTrafficPortShapedSpeedLo Unsigned32
  cmEthernetTrafficPortShapedSpeedHi Unsigned32
  cmEthernetTrafficPortQinQEtherType Unsigned32
  cmEthernetTrafficPortTagFrameControl AfpTagControl
  cmEthernetTrafficPortEgressVlanTrunkingEnabled TruthValue
  cmEthernetTrafficPortIngressPushPVIDEnabled TruthValue
  cmEthernetTrafficPortEgressPopPVIDEnabled TruthValue
  cmEthernetTrafficPortEgressPopPriorityVidEnabled TruthValue
  cmEthernetTrafficPortPortVlanId VlanId
  cmEthernetTrafficPortPortVlanPriority VlanPriority
  cmEthernetTrafficPortPriorityVlanId VlanId
  cmEthernetTrafficPortIngressPrioMapMode PriorityMapMode
  cmEthernetTrafficPortIngressCOSPriority VlanTagType
  cmEthernetTrafficPortSyncEEnabled TruthValue
  cmEthernetTrafficPortQLModeEnabled TruthValue
  cmEthernetTrafficPortExpectedQL SSMQualityLevel
  cmEthernetTrafficPortAssumedQL SSMQualityLevel
  cmEthernetTrafficPortReceivedQL SSMQualityLevel
  cmEthernetTrafficPortTransmitQL SSMQualityLevel
  cmEthernetTrafficPortPhyType XgePhyType
  cmEthernetTrafficPortSfpLaserWaveLengthPicometer Unsigned32
  cmEthernetTrafficPortRowStatus RowStatus
  cmEthernetTrafficPortSSMRemoteMacAddress MacAddress
  cmEthernetTrafficPortInnerVlanLoopbackMask INTEGER
  cmEthernetTrafficPortInnerVlanLoopback1 DisplayString
  cmEthernetTrafficPortInnerVlanLoopback2 DisplayString
  cmEthernetTrafficPortInnerVlanLoopback3 DisplayString
  cmEthernetTrafficPortLaserWDMChannel SfpChannelIdentifier
  cmEthernetTrafficPortLaserIsTunable TruthValue
  cmEthernetTrafficPortLaserFrequency Unsigned32
  cmEthernetTrafficPortDeiEnable TruthValue
  cmEthernetTrafficPortPcpDEEncType PcpDEEncType
  cmEthernetTrafficPortPcpDEPairsAction PcpDEPairsAction
  cmEthernetTrafficPortInitiateDiag CmEthernetDiagAction
  cmEthernetTrafficPortDiagnosePair1Cond CmDiagCableCondType
  cmEthernetTrafficPortDiagnosePair2Cond CmDiagCableCondType
  cmEthernetTrafficPortDiagnosePair3Cond CmDiagCableCondType
  cmEthernetTrafficPortDiagnosePair4Cond CmDiagCableCondType
  cmEthernetTrafficPortDiagnoseAutoNegCond CmDiagAutoNegCondType
  cmEthernetTrafficPortDiagnoseLpbkCond CmDiagLpbkCondType
  cmEthernetTrafficPortDiagnoseEfmLpbkCond CmDiagEfmOamLpbkCondType
  cmEthernetTrafficPortDiagnoseResult DisplayString
  cmEthernetTrafficPortDiagnoseTestStatus CmDiagTestStatus
  cmEthernetTrafficPortDiagnoseTestTime DateAndTime
  cmEthernetTrafficPortAutoDiagEnabled TruthValue
  cmEthernetTrafficPortDeleteEntitiesAction TrafficPortDeleteEntitiesAction
  cmEthernetTrafficPortMaxMpFpNum Integer32
  cmEthernetTrafficPortJdsuLoopbackEnabled TruthValue
  cmEthernetTrafficPortJdsuLoopbackVlanId VlanId
  cmEthernetTrafficPortIngressPopPriorityVidEnabled TruthValue
  cmEthernetTrafficPortRxDeiAction RxDeiAction
  cmEthernetTrafficPortTxDeiAction TxDeiAction
  cmEthernetTrafficPortRxDeiOuterTagType DeiOuterTagType
  cmEthernetTrafficPortTxDeiOuterTagType DeiOuterTagType

CmElineFlowEntry  
SEQUENCE    
  cmElineFlowIndex Integer32
  cmElineFlowCircuitName DisplayString
  cmElineFlowAdminState AdminState
  cmElineFlowOperationalState OperationalState
  cmElineFlowSecondaryState SecondaryState
  cmElineFlowFP1 VariablePointer
  cmElineFlowFP2 VariablePointer
  cmElineFlowStorageType StorageType
  cmElineFlowRowStatus RowStatus

CmFlowPointEntry  
SEQUENCE    
  cmFlowPointIndex Integer32
  cmFlowPointCircuitName DisplayString
  cmFlowPointAdminState AdminState
  cmFlowPointOperationalState OperationalState
  cmFlowPointSecondaryState SecondaryState
  cmFlowPointAssociatedFlowId VariablePointer
  cmFlowPointIngressMultiCOS TruthValue
  cmFlowPointIngressCOS Integer32
  cmFlowPointIngressVlanMemberList DisplayString
  cmFlowPointVlanMemberAction FlowVlanActionType
  cmFlowPointVlanMemberActionVlan DisplayString
  cmFlowPointIngressUntaggedFrameEnabled TruthValue
  cmFlowPointCTagControl FlowTagControl
  cmFlowPointCTagVlanId VlanId
  cmFlowPointCTagVlanPriority VlanPriority
  cmFlowPointSTagControl FlowTagControl
  cmFlowPointSTagVlanId VlanId
  cmFlowPointSTagVlanPriority VlanPriority
  cmFlowPointEgressOuterTagPrioMapEnabled TruthValue
  cmFlowPointColorMarkingSupported TruthValue
  cmFlowPointAssociatedAclProfile VariablePointer
  cmFlowPointSESFramesLossThresholdRatio Integer32
  cmFlowPointStorageType StorageType
  cmFlowPointRowStatus RowStatus
  cmFlowPointDefaultMemberEnabled TruthValue
  cmFlowPointMcastRateLimitEnabled TruthValue
  cmFlowPointMcastRateLimitSpeedLo Unsigned32
  cmFlowPointMcastRateLimitSpeedHi Unsigned32
  cmFlowPointBcastRateLimitEnabled TruthValue
  cmFlowPointBcastRateLimitSpeedLo Unsigned32
  cmFlowPointBcastRateLimitSpeedHi Unsigned32
  cmFlowPointSplitHorizonGroupOID VariablePointer
  cmFlowPointLoopAvoidance VariablePointer
  cmFlowPointHierarchicalCosEnabled TruthValue
  cmFlowPointWfqQid Integer32
  cmFlowPointWfqOutPriority Integer32
  cmFlowPointMaximumBWLo Unsigned32
  cmFlowPointMaximumBWHi Unsigned32
  cmFlowPointGuaranteedBWLo Unsigned32
  cmFlowPointGuaranteedBWHi Unsigned32
  cmFlowPointRefPrioMapProfile VariablePointer
  cmFlowPointMcastAndBcastRateLimitEnabled TruthValue
  cmFlowPointMcastAndBcastRateLimitSpeedLo Unsigned32
  cmFlowPointMcastAndBcastRateLimitSpeedHi Unsigned32

CmOAMFlowPointEntry  
SEQUENCE    
  cmOAMFlowPointIndex Integer32
  cmOAMFlowPointCircuitName DisplayString
  cmOAMFlowPointAdminState AdminState
  cmOAMFlowPointOperationalState OperationalState
  cmOAMFlowPointSecondaryState SecondaryState
  cmOAMFlowPointIngressVlanMemberList DisplayString
  cmOAMFlowPointVlanMemberAction FlowVlanActionType
  cmOAMFlowPointVlanMemberActionVlan DisplayString
  cmOAMFlowPointIngressUntaggedFrameSupported TruthValue
  cmOAMFlowPointSESFramesLossThresholdRatio Integer32
  cmOAMFlowPointStorageType StorageType
  cmOAMFlowPointRowStatus RowStatus

CmIngressPrioMapEntry  
SEQUENCE    
  cmIngressPrioMapIndex Integer32
  cmIngressPrioMapInPriority Integer32
  cmIngressPrioMapCOS Integer32

CmEgressPrioMapEntry  
SEQUENCE    
  cmEgressCOSIndex Integer32
  cmEgressCOS Integer32
  cmEgressOuterTagCtrl PrioMapControlType
  cmEgressOuterTagPriority VlanPriority

CmPortCpdProfileEntry  
SEQUENCE    
  cmPortCpdProfileIndex Integer32
  cmPortCpdProfileName DisplayString
  cmPortCpdProfileCiscoGroupDispType CmControlProtocolDispType
  cmPortCpdProfileIslDispType CmControlProtocolDispType
  cmPortCpdProfilePagpDispType CmControlProtocolDispType
  cmPortCpdProfileUdldDispType CmControlProtocolDispType
  cmPortCpdProfileCdpDispType CmControlProtocolDispType
  cmPortCpdProfileVtpDispType CmControlProtocolDispType
  cmPortCpdProfileDtpDispType CmControlProtocolDispType
  cmPortCpdProfilePvstpPlusDispType CmControlProtocolDispType
  cmPortCpdProfileUplinkFastDispType CmControlProtocolDispType
  cmPortCpdProfileVlanBridgeDispType CmControlProtocolDispType
  cmPortCpdProfileL2PTDispType CmControlProtocolDispType
  cmPortCpdProfileBridgeGroupDispType CmControlProtocolDispType
  cmPortCpdProfileBPDUDispType CmControlProtocolDispType
  cmPortCpdProfilePauseDispType CmControlProtocolDispType
  cmPortCpdProfileLACPDispType CmControlProtocolDispType
  cmPortCpdProfileLACPMarkerDispType CmControlProtocolDispType
  cmPortCpdProfileEfmOamDispType CmControlProtocolDispType
  cmPortCpdProfileSSMDispType CmControlProtocolDispType
  cmPortCpdProfilePortAuthenDispType CmControlProtocolDispType
  cmPortCpdProfileBridgeReservedDispType CmControlProtocolDispType
  cmPortCpdProfileLANBridgesDispType CmControlProtocolDispType
  cmPortCpdProfileGARPGroupDispType CmControlProtocolDispType
  cmPortCpdProfileGMRPDispType CmControlProtocolDispType
  cmPortCpdProfileGVRPDispType CmControlProtocolDispType
  cmPortCpdProfileGARPDispType CmControlProtocolDispType
  cmPortCpdProfileLldpDispType CmControlProtocolDispType
  cmPortCpdProfileStorageType StorageType
  cmPortCpdProfileRowStatus RowStatus
  cmPortCpdProfileMac00DispType CmControlProtocolDispType
  cmPortCpdProfileMac01DispType CmControlProtocolDispType
  cmPortCpdProfileMac02DispType CmControlProtocolDispType
  cmPortCpdProfileMac03DispType CmControlProtocolDispType
  cmPortCpdProfileMac04DispType CmControlProtocolDispType
  cmPortCpdProfileMac05DispType CmControlProtocolDispType
  cmPortCpdProfileMac06DispType CmControlProtocolDispType
  cmPortCpdProfileMac07DispType CmControlProtocolDispType
  cmPortCpdProfileMac08DispType CmControlProtocolDispType
  cmPortCpdProfileMac09DispType CmControlProtocolDispType
  cmPortCpdProfileMac0ADispType CmControlProtocolDispType
  cmPortCpdProfileMac0BDispType CmControlProtocolDispType
  cmPortCpdProfileMac0CDispType CmControlProtocolDispType
  cmPortCpdProfileMac0DDispType CmControlProtocolDispType
  cmPortCpdProfileMac0EDispType CmControlProtocolDispType
  cmPortCpdProfileMac0FDispType CmControlProtocolDispType
  cmPortCpdProfileNearestLLDPDispType CmControlProtocolDispType
  cmPortCpdProfileNonTpmrLLDPDispType CmControlProtocolDispType
  cmPortCpdProfileCustomerLLDPDispType CmControlProtocolDispType
  cmPortCpdProfileELMIDispType CmControlProtocolDispType

CmFlowPointCpdProfileEntry  
SEQUENCE    
  cmFlowPointCpdProfileIndex Integer32
  cmFlowPointCpdProfileName DisplayString
  cmFlowPointCpdProfileCiscoGroupDispType CmControlProtocolDispType
  cmFlowPointCpdProfileIslDispType CmControlProtocolDispType
  cmFlowPointCpdProfilePagpDispType CmControlProtocolDispType
  cmFlowPointCpdProfileUdldDispType CmControlProtocolDispType
  cmFlowPointCpdProfileCdpDispType CmControlProtocolDispType
  cmFlowPointCpdProfileVtpDispType CmControlProtocolDispType
  cmFlowPointCpdProfileDtpDispType CmControlProtocolDispType
  cmFlowPointCpdProfilePvstpPlusDispType CmControlProtocolDispType
  cmFlowPointCpdProfileUplinkFastDispType CmControlProtocolDispType
  cmFlowPointCpdProfileVlanBridgeDispType CmControlProtocolDispType
  cmFlowPointCpdProfileL2PTDispType CmControlProtocolDispType
  cmFlowPointCpdProfileBridgeGroupDispType CmControlProtocolDispType
  cmFlowPointCpdProfileBPDUDispType CmControlProtocolDispType
  cmFlowPointCpdProfilePauseDispType CmControlProtocolDispType
  cmFlowPointCpdProfileLACPDispType CmControlProtocolDispType
  cmFlowPointCpdProfileLACPMarkerDispType CmControlProtocolDispType
  cmFlowPointCpdProfileEfmOamDispType CmControlProtocolDispType
  cmFlowPointCpdProfileSSMDispType CmControlProtocolDispType
  cmFlowPointCpdProfilePortAuthenDispType CmControlProtocolDispType
  cmFlowPointCpdProfileBridgeReservedDispType CmControlProtocolDispType
  cmFlowPointCpdProfileLANBridgesDispType CmControlProtocolDispType
  cmFlowPointCpdProfileGARPGroupDispType CmControlProtocolDispType
  cmFlowPointCpdProfileGMRPDispType CmControlProtocolDispType
  cmFlowPointCpdProfileGVRPDispType CmControlProtocolDispType
  cmFlowPointCpdProfileGARPDispType CmControlProtocolDispType
  cmFlowPointCpdProfileLldpDispType CmControlProtocolDispType
  cmFlowPointCpdProfileStorageType StorageType
  cmFlowPointCpdProfileRowStatus RowStatus
  cmFlowPointCpdProfileMac00DispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac01DispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac02DispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac03DispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac04DispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac05DispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac06DispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac07DispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac08DispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac09DispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac0ADispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac0BDispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac0CDispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac0DDispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac0EDispType CmControlProtocolDispType
  cmFlowPointCpdProfileMac0FDispType CmControlProtocolDispType
  cmFlowPointCpdProfileNearestLLDPDispType CmControlProtocolDispType
  cmFlowPointCpdProfileNonTpmrLLDPDispType CmControlProtocolDispType
  cmFlowPointCpdProfileCustomerLLDPDispType CmControlProtocolDispType
  cmFlowPointCpdProfileELMIDispType CmControlProtocolDispType

CmEthernetTrafficPortCpdEntry  
SEQUENCE    
  cmEthernetTrafficPortCpdIndex Integer32
  cmEthernetTrafficPortAssociatedCpdProfile VariablePointer

CmEthernetFlowPointCpdEntry  
SEQUENCE    
  cmEthernetFlowPointCpdIndex Integer32
  cmEthernetFlowPointAssociatedCpdProfile VariablePointer

CmTrafficAclProfileEntry  
SEQUENCE    
  cmTrafficAclProfileIndex Integer32
  cmTrafficAclProfileName DisplayString
  cmTrafficAclProfileStorageType StorageType
  cmTrafficAclProfileRowStatus RowStatus

CmTrafficAclRulesEntry  
SEQUENCE    
  cmTrafficAclRulesIndex Integer32
  cmTrafficAclFilterAction CmTrafficAclFilterActionType
  cmTrafficAclFilterType CmTrafficAclFilterType
  cmTrafficAclEnabled TruthValue
  cmTrafficAclSrcMacAddr MacAddress
  cmTrafficAclSrcMacAddrEnabled TruthValue
  cmTrafficAclDstMacAddr MacAddress
  cmTrafficAclDstMacAddrEnabled TruthValue
  cmTrafficAclSrcIpFilterEnabled TruthValue
  cmTrafficAclDstIpFilterEnabled TruthValue
  cmTrafficAclSrcIpV4Addr IpAddress
  cmTrafficAclSrcIpV4AddrMask IpAddress
  cmTrafficAclDstIpV4Addr IpAddress
  cmTrafficAclDstIpV4AddrMask IpAddress
  cmTrafficAclSrcIpV6Addr Ipv6Address
  cmTrafficAclSrcIpV6AddrMask Ipv6Address
  cmTrafficAclDstIpV6Addr Ipv6Address
  cmTrafficAclDstIpV6AddrMask Ipv6Address
  cmTrafficAclTcpUdpSrcPortNum Integer32
  cmTrafficAclTcpUdpSrcPortMask Integer32
  cmTrafficAclTcpUdpSrcPortEnabled TruthValue
  cmTrafficAclTcpUdpDstPortNum Integer32
  cmTrafficAclTcpUdpDstPortMask Integer32
  cmTrafficAclTcpUdpDstPortEnabled TruthValue
  cmTrafficAclIpQosType CmTrafficACLPriorityType
  cmTrafficAclIpQosValue Integer32
  cmTrafficAclIpQosTypeEnabled TruthValue
  cmTrafficAclVlanId VlanId
  cmTrafficAclVlanIdEnabled TruthValue
  cmTrafficAclVlanPriority Integer32
  cmTrafficAclVlanPriorityEnabled TruthValue
  cmTrafficAclProtocolType CmTrafficAclProtocolType
  cmTrafficAclProtocolTypeEnabled TruthValue
  cmTrafficAclStorageType StorageType
  cmTrafficAclRowStatus RowStatus

CmQosPolicerProfileEntry  
SEQUENCE    
  cmQosPolicerProfileIndex Integer32
  cmQosPolicerProfileName DisplayString
  cmQosPolicerProfileCIRLo Unsigned32
  cmQosPolicerProfileCIRHi Unsigned32
  cmQosPolicerProfileEIRLo Unsigned32
  cmQosPolicerProfileEIRHi Unsigned32
  cmQosPolicerProfileCBS Integer32
  cmQosPolicerProfileEBS Integer32
  cmQosPolicerProfileColorMode PolicerColorMode
  cmQosPolicerProfileCouplingFlag TruthValue
  cmQosPolicerProfileStorageType StorageType
  cmQosPolicerProfileRowStatus RowStatus

CmQosQueueProfileEntry  
SEQUENCE    
  cmQosQueueProfileIndex Integer32
  cmQosQueueProfileName DisplayString
  cmQosQueueProfileBufferSize Integer32
  cmQosQueueProfileREDEnabled TruthValue
  cmQosQueueProfileStorageType StorageType
  cmQosQueueProfileRowStatus RowStatus

CmQosPolicerV2Entry  
SEQUENCE    
  cmQosPolicerV2Index Integer32
  cmQosPolicerV2AdminState AdminState
  cmQosPolicerV2OperationalState OperationalState
  cmQosPolicerV2SecondaryState SecondaryState
  cmQosPolicerV2ColorMarkingEnabled TruthValue
  cmQosPolicerV2AssociatedProfile VariablePointer
  cmQosPolicerV2StorageType StorageType
  cmQosPolicerV2RowStatus RowStatus
  cmQosPolicerV2PolicingEnabled TruthValue

CmQosShaperV2Entry  
SEQUENCE    
  cmQosShaperV2Index Integer32
  cmQosShaperV2AdminState AdminState
  cmQosShaperV2OperationalState OperationalState
  cmQosShaperV2SecondaryState SecondaryState
  cmQosShaperV2AssociatedQueueProfile VariablePointer
  cmQosShaperV2CIRLo Unsigned32
  cmQosShaperV2CIRHi Unsigned32
  cmQosShaperV2EIRLo Unsigned32
  cmQosShaperV2EIRHi Unsigned32
  cmQosShaperV2IngressAverageFrameSize Integer32
  cmQosShaperV2StorageType StorageType
  cmQosShaperV2RowStatus RowStatus
  cmQosShaperV2AdditionalCIRLo Unsigned32
  cmQosShaperV2AdditionalCIRHi Unsigned32
  cmQosShaperV2WFQWeight Integer32
  cmQosShaperV2ActualCIR Counter64
  cmQosShaperV2ActualEIR Counter64
  cmQosShaperV2LowLatencyControl TruthValue

CmTrafficPortQosShaperEntry  
SEQUENCE    
  cmTrafficPortQosShaperIndex Integer32
  cmTrafficPortQosShaperAdminState AdminState
  cmTrafficPortQosShaperOperationalState OperationalState
  cmTrafficPortQosShaperSecondaryState SecondaryState
  cmTrafficPortQosShaperAssociatedQueueProfile VariablePointer
  cmTrafficPortQosShaperBufferSize Integer32
  cmTrafficPortQosShaperCIRLo Unsigned32
  cmTrafficPortQosShaperCIRHi Unsigned32
  cmTrafficPortQosShaperEIRLo Unsigned32
  cmTrafficPortQosShaperEIRHi Unsigned32
  cmTrafficPortQosShaperStorageType StorageType
  cmTrafficPortQosShaperRowStatus RowStatus
  cmTrafficPortQosShaperIngressAverageFrameSize Integer32
  cmTrafficPortQosShaperAdditionalCIRLo Unsigned32
  cmTrafficPortQosShaperAdditionalCIRHi Unsigned32

F3NetPortQosShaperEntry  
SEQUENCE    
  f3NetPortQosShaperIndex Integer32
  f3NetPortQosShaperDirection TrafficDirection
  f3NetPortQosShaperAdminState AdminState
  f3NetPortQosShaperOperationalState OperationalState
  f3NetPortQosShaperSecondaryState SecondaryState
  f3NetPortQosShaperCIRLo Unsigned32
  f3NetPortQosShaperCIRHi Unsigned32
  f3NetPortQosShaperEIRLo Unsigned32
  f3NetPortQosShaperEIRHi Unsigned32
  f3NetPortQosShaperCBS Unsigned32
  f3NetPortQosShaperEBS Unsigned32
  f3NetPortQosShaperBufferSize Unsigned32
  f3NetPortQosShaperCOS Integer32
  f3NetPortQosShaperSoamCIRLo Unsigned32
  f3NetPortQosShaperSoamCIRHi Unsigned32
  f3NetPortQosShaperSoamEIRLo Unsigned32
  f3NetPortQosShaperSoamEIRHi Unsigned32
  f3NetPortQosShaperWredGreenMinQueueThreshold Unsigned32
  f3NetPortQosShaperWredGreenMaxQueueThreshold Unsigned32
  f3NetPortQosShaperWredGreenDropProbability Unsigned32
  f3NetPortQosShaperWredYellowMinQueueThreshold Unsigned32
  f3NetPortQosShaperWredYellowMaxQueueThreshold Unsigned32
  f3NetPortQosShaperWredYellowDropProbability Unsigned32

F3Usb3GDCNPortEntry  
SEQUENCE    
  f3Usb3GDCNPortIndex Integer32
  f3Usb3GDCNPortIfIndex InterfaceIndex
  f3Usb3GDCNPortEntityIndex PhysicalIndex
  f3Usb3GDCNPortAdminState AdminState
  f3Usb3GDCNPortOperationalState OperationalState
  f3Usb3GDCNPortSecondaryState SecondaryState
  f3Usb3GDCNPortVendorName DisplayString
  f3Usb3GDCNPortModel DisplayString
  f3Usb3GDCNPortFSN DisplayString
  f3Usb3GDCNPortIMEI DisplayString
  f3Usb3GDCNPortHardwareVersion DisplayString
  f3Usb3GDCNPortFirmwareVersion DisplayString
  f3Usb3GDCNPortSIMStatus F3Usb3GSimCardState
  f3Usb3GDCNPortPINLeftChances Integer32
  f3Usb3GDCNPortPUKLeftChances Integer32
  f3Usb3GDCNPortConnectionStatus F3Usb3GNetworkConnectionState
  f3Usb3GDCNPortRSSI F3Usb3GRecvSignalStrengthInd
  f3Usb3GDCNPortSpeed Integer32
  f3Usb3GDCNPortMTU Integer32
  f3Usb3GDCNPortProviderName DisplayString
  f3Usb3GDCNPortDNS1 IpAddress
  f3Usb3GDCNPortDNS2 IpAddress
  f3Usb3GDCNPortAPN DisplayString
  f3Usb3GDCNPortUserName DisplayString
  f3Usb3GDCNPortPassword DisplayString
  f3Usb3GDCNPortDailNumber DisplayString
  f3Usb3GDCNPortRedialTimer Integer32
  f3Usb3GDCNPortCurrentPinCode DisplayString
  f3Usb3GDCNPortNewPinCode DisplayString
  f3Usb3GDCNPortConfirmPinCode DisplayString
  f3Usb3GDCNPortCurrentPukCode DisplayString
  f3Usb3GDCNPINCodeAction F3Usb3GDCNPINCodeActionType
  f3Usb3GDCNPortStorageType StorageType
  f3Usb3GDCNPortRowStatus RowStatus
  f3Usb3GDCNPortIMSI DisplayString
  f3Usb3GDCNPortPINStatus G3AuthStatus
  f3UsbDCNPortMobileNetworkType UsbDCNMobileNetworkType

OcnStmEntry  
SEQUENCE    
  ocnStmIndex Integer32
  ocnStmIfIndex InterfaceIndex
  ocnStmEntityIndex PhysicalIndex
  ocnStmAdminState AdminState
  ocnStmOperationalState OperationalState
  ocnStmSecondaryState SecondaryState
  ocnStmSfpVendorName DisplayString
  ocnStmSfpPartNumber DisplayString
  ocnStmSfpSerialNumber DisplayString
  ocnStmSfpDateOfManufacture DateAndTime
  ocnStmSfpConnectorValue SfpConnectorValue
  ocnStmSfpLinkLength Integer32
  ocnStmSfpLaserWaveLength Integer32
  ocnStmSfpLaserWaveLengthPicometer Unsigned32
  ocnStmSfpMediaType SfpMediaType
  ocnStmMultiplexingStructures MultiplexingStructure
  ocnStmEoTDMMode EoTDMMode
  ocnStmLoopbackConfig CmLoopbackType
  ocnStmLoopbackStatus CmLoopbackType
  ocnStmLoopbackTime Integer32
  ocnStmInsertingAIS TruthValue
  ocnStmBerExcThreshold BitErrRate
  ocnStmBerDegThreshold BitErrRate
  ocnStmRxTrailTrace DisplayString
  ocnStmTxTrailTrace DisplayString
  ocnStmExpectedTrailTrace DisplayString
  ocnStmTrailTraceFormat TrailTraceFormat
  ocnStmQLModeEnabled TruthValue
  ocnStmExpectedQL SSMQualityLevel
  ocnStmAssumedQL SSMQualityLevel
  ocnStmReceivedQL SSMQualityLevel
  ocnStmTransmitQL SSMQualityLevel
  ocnStmPortType OCNSTMPortType
  ocnStmFreqSourceType TDMFrequencySourceType
  ocnStmHighOrderPathType TDMPathType

StsVcPathEntry  
SEQUENCE    
  stsVcPathParentIfIndex InterfaceIndex
  stsVcPathIndex Unsigned32
  stsVcPathIfIndex InterfaceIndex
  stsVcPathAdminState AdminState
  stsVcPathOperationalState OperationalState
  stsVcPathSecondaryState SecondaryState
  stsVcPathLoopbackConfig CmLoopbackType
  stsVcPathLoopbackStatus CmLoopbackType
  stsVcPathLoopbackTime Integer32
  stsVcPathInsertingAIS TruthValue
  stsVcPathBerExcThreshold BitErrRate
  stsVcPathBerDegThreshold BitErrRate
  stsVcPathTrailTraceFormat TrailTraceFormat
  stsVcPathRxTrailTrace DisplayString
  stsVcPathTxTrailTrace DisplayString
  stsVcPathExpectedTrailTrace DisplayString
  stsVcPathRxSignalLabel Unsigned32
  stsVcPathTxSignalLabel Unsigned32
  stsVcPathExpectedSignalLabel Unsigned32
  stsVcPathRowStatus RowStatus
  stsVcPathLowOrderPathType TDMPathType

VtVcPathEntry  
SEQUENCE    
  vtVcPathParentIfIndex InterfaceIndex
  vtVcPathIndex Unsigned32
  vtVcPathIfIndex InterfaceIndex
  vtVcPathAdminState AdminState
  vtVcPathOperationalState OperationalState
  vtVcPathSecondaryState SecondaryState
  vtVcPathLoopbackConfig CmLoopbackType
  vtVcPathLoopbackStatus CmLoopbackType
  vtVcPathLoopbackTime Integer32
  vtVcPathInsertingAIS TruthValue
  vtVcPathBerExcThreshold BitErrRate
  vtVcPathBerDegThreshold BitErrRate
  vtVcPathTrailTraceFormat TrailTraceFormat
  vtVcPathRxTrailTrace DisplayString
  vtVcPathTxTrailTrace DisplayString
  vtVcPathExpectedTrailTrace DisplayString
  vtVcPathRxSignalLabel Unsigned32
  vtVcPathTxSignalLabel Unsigned32
  vtVcPathExpectedSignalLabel Unsigned32
  vtVcPathRowStatus RowStatus

E1T1Entry  
SEQUENCE    
  e1t1ParentIfIndex InterfaceIndex
  e1t1Index Unsigned32
  e1t1IfIndex InterfaceIndex
  e1t1EntityIndex PhysicalIndex
  e1t1AdminState AdminState
  e1t1OperationalState OperationalState
  e1t1SecondaryState SecondaryState
  e1t1LoopbackConfig CmLoopbackType
  e1t1LoopbackStatus CmLoopbackType
  e1t1LoopbackTime Integer32
  e1t1RemoteLoopbackRequest TruthValue
  e1t1InsertingAIS TruthValue
  e1t1RowStatus RowStatus
  e1t1LineType E1T1LineType
  e1t1LineCode E1T1LineCode
  e1t1FrameFormat E1T1FrameFormat
  e1t1LineBuildOut LineBuildOut
  e1t1TimingDomain VariablePointer
  e1t1RcvSensitivity E1T1RcvSensitivity
  e1t1IdlePatternProfile VariablePointer
  e1t1LoopbackProfile VariablePointer
  e1t1RelatedContainerId VariablePointer

E3T3Type  
Describes the type of the E3/T3.
TEXTUAL-CONVENTION    
  INTEGER none(0), e3(1), t3(2)  

E3T3Entry  
SEQUENCE    
  e3t3ParentIfIndex InterfaceIndex
  e3t3Index Unsigned32
  e3t3IfIndex InterfaceIndex
  e3t3EntityIndex PhysicalIndex
  e3t3AdminState AdminState
  e3t3OperationalState OperationalState
  e3t3SecondaryState SecondaryState
  e3t3LoopbackConfig CmLoopbackType
  e3t3LoopbackStatus CmLoopbackType
  e3t3LoopbackTime Integer32
  e3t3RemoteLoopbackRequest TruthValue
  e3t3InsertingAIS TruthValue
  e3t3CBitEnable TruthValue
  e3t3T3Channelized TruthValue
  e3t3RowStatus RowStatus
  e3t3FrameFormat E3T3FrameFormat
  e3t3RelatedContainerId VariablePointer

CmEthernetTrafficPortExtEntry  
SEQUENCE    
  cmEthernetTrafficPortTDMEncapsulation GFPEncapsulationType
  cmEthernetTrafficPortRelatedVCG VariablePointer

F3PulsePerSecondPortEntry  
SEQUENCE    
  f3PulsePerSecondPortIndex Integer32
  f3PulsePerSecondPortIfIndex InterfaceIndex
  f3PulsePerSecondPortEntityIndex PhysicalIndex
  f3PulsePerSecondPortAdminState AdminState
  f3PulsePerSecondPortOperationalState OperationalState
  f3PulsePerSecondPortSecondaryState SecondaryState
  f3PulsePerSecondPortSquelchControl SquelchControl
  f3PulsePerSecondPortSquelchQL SSMQualityLevel
  f3PulsePerSecondPortTODSource VariablePointer
  f3PulsePerSecondPortDirection SignalDirectionType
  f3PulsePerSecondPortInputRate PPSInputRate
  f3PulsePerSecondPortDelayCompensation Integer32
  f3PulsePerSecondPortClockClass Unsigned32
  f3PulsePerSecondPortClockAccuracy Unsigned32
  f3PulsePerSecondPortTimeSource TimeSource
  f3PulsePerSecondPortPhyInterfaceType PPSPhyInterfaceType

F3TimeOfDayPortEntry  
SEQUENCE    
  f3TimeOfDayPortIndex Integer32
  f3TimeOfDayPortIfIndex InterfaceIndex
  f3TimeOfDayPortEntityIndex PhysicalIndex
  f3TimeOfDayPortAdminState AdminState
  f3TimeOfDayPortOperationalState OperationalState
  f3TimeOfDayPortSecondaryState SecondaryState
  f3TimeOfDayPortSquelchControl SquelchControl
  f3TimeOfDayPortSquelchQL SSMQualityLevel
  f3TimeOfDayPortTODSource VariablePointer

CmEthernetNetPortExtEntry  
SEQUENCE    
  cmEthernetNetPortTDMEncapsulation GFPEncapsulationType
  cmEthernetNetPortAssociatedTdmEntity VariablePointer
  cmEthernetNetPortInsertingAIS TruthValue

F3GPSReceiverPortEntry  
SEQUENCE    
  f3GPSReceiverPortIndex Integer32
  f3GPSReceiverPortIfIndex InterfaceIndex
  f3GPSReceiverPortEntityIndex PhysicalIndex
  f3GPSReceiverPortAdminState AdminState
  f3GPSReceiverPortOperationalState OperationalState
  f3GPSReceiverPortSecondaryState SecondaryState
  f3GPSReceiverPortPPSGenCondition PPSGenCondition
  f3GPSReceiverPortAntennaCableLength Unsigned32
  f3GPSReceiverPortAntennaStatus GPSAntennaStatus
  f3GPSReceiverPortSatellitesUsableFlag TruthValue
  f3GPSReceiverPortNumTrackingSatellites Unsigned32
  f3GPSReceiverPortSelfSurveyProgress Unsigned32
  f3GPSReceiverPortPPSGeneratedFlag TruthValue
  f3GPSReceiverPortGnssSystem ConstellationType
  f3GPSReceiverPortInstallationType InstallationType
  f3GPSReceiverPortGnssTOD DateAndTime
  f3GPSReceiverPortGnssSystemsBitMap ConstellationTypesBitMap
  f3GPSReceiverPortAlias DisplayString

CmPethPsePortExtEntry  
SEQUENCE    
  cmPethPsePortExtGroupIndex Integer32
  cmPethPsePortExtIndex Integer32
  cmPethPsePortExtAssociatedPort VariablePointer
  pethPsePortExtPowerConsumption Unsigned32
  pethPsePortExtAvailablePowerLevel PsePowerLevel

PethMainPseEXTEntry  
SEQUENCE    
  pethMainPseExtGroupIndex Integer32
  pethMainPseExtNonStandardPD PSENonStandardPD

CmMPFlowEntry  
SEQUENCE    
  cmMPFlowIndex Integer32
  cmMPFlowCircuitName F3DisplayString
  cmMPFlowAdminState AdminState
  cmMPFlowOperationalState OperationalState
  cmMPFlowSecondaryState SecondaryState
  cmMPFlowLearningEnabled TruthValue
  cmMPFlowAgingTimer Integer32
  cmMPFlowFwdTableSizeProfileID VariablePointer
  cmMPFlowtableFullAction LearningAction
  cmMPFlowStorageType StorageType
  cmMPFlowRowStatus RowStatus
  cmMPFlowLearningConfigAction LearningConfigAction
  cmMPFlowFPList F3DisplayString

CmMPFlowMemberEntry  
SEQUENCE    
  cmMPFlowMemberFPIndex VariablePointer
  cmMPFlowPointRowStatus RowStatus

CmEthernetTrafficPortPcpDEEncEntry  
SEQUENCE    
  cmEthernetTrafficPortPcpDEEncIndex Integer32
  cmEthernetTrafficPortPcpDEEncInPriority VlanPriority
  cmEthernetTrafficPortPcpDEEncDropIneligiblePrio VlanPriority
  cmEthernetTrafficPortPcpDEEncDropEligiblePrio VlanPriority

CmEthernetTrafficPortPcpDEDecEntry  
SEQUENCE    
  cmEthernetTrafficPortPcpDEDecIndex Integer32
  cmEthernetTrafficPortPcpDEDecInPriority VlanPriority
  cmEthernetTrafficPortPcpDEDecOutPriority VlanPriority
  cmEthernetTrafficPortPcpDEDecDropEligible TruthValue

CmEthernetTrafficPortPcpDEPairEntry  
SEQUENCE    
  cmEthernetTrafficPortPcpDEPairIndex Integer32
  cmEthernetTrafficPortPcpDEDropIneligiblePrio VlanPriority
  cmEthernetTrafficPortPcpDEDropEligiblePrio VlanPriority

CmEthernetTrafficPortClbEntry  
SEQUENCE    
  cmEthernetTrafficPortClbIndex Integer32
  cmEthernetTrafficPortClbEnabled TruthValue
  cmEthernetTrafficPortClbLength DisplayString
  cmEthernetTrafficPortClbDescr DisplayString

NetworkElementTMParamsEntry  
SEQUENCE    
  neTMParamsBandwidthProfileMode BandwidthProfileMode
  neTMParamsAgingtime Integer32

CmEthernetAccPortJdsuExtEntry  
SEQUENCE    
  cmEthernetAccPortJDSUControlFramesSnoopingEnabled TruthValue
  cmEthernetAccPortJDSULoopbackVlan VlanId

CmEthernetNetPortJdsuExtEntry  
SEQUENCE    
  cmEthernetNetPortJDSUControlFramesSnoopingEnabled TruthValue
  cmEthernetNetPortJDSULoopbackVlan VlanId

CmEthernetTrafficPortLpbkEntry  
SEQUENCE    
  cmEthernetTrafficPortLpbkIndex Integer32
  cmEthernetTrafficPortLpbkInnerVlanEnabled TruthValue
  cmEthernetTrafficPortLpbkInnerVlanTag DisplayString
  cmEthernetTrafficPortLpbkOuterVlanEnabled TruthValue
  cmEthernetTrafficPortLpbkOuterVlanTag DisplayString
  cmEthernetTrafficPortLpbkTime Integer32
  cmEthernetTrafficPortLpbkStatus CmLoopbackType
  cmEthernetTrafficPortLpbkConfig CmLoopbackType

CmPrioMapV2ProfileEntry  
SEQUENCE    
  cmPrioMapV2ProfileIndex Integer32
  cmPrioMapV2ProfileAlias DisplayString
  cmPrioMapV2ProfileMapModeType PriorityMapMode
  cmPrioMapV2ProfileStorageType StorageType
  cmPrioMapV2ProfileRowStatus RowStatus
  cmPrioMapV2ProfileIngressCosPriority VlanTagType
  cmPrioMapV2ProfileCosMapModeType CosMappingMode
  cmPrioMapV2ProfileCosMapControl TruthValue
  cmPrioMapV2ProfileDefaultCos Unsigned32

CmPrioMapV2IngressPrioMappingEntry  
SEQUENCE    
  cmPrioMapV2IngressPrioMappingIndex Integer32
  cmPrioMapV2IngressPrioMappingInPriority Integer32
  cmPrioMapV2IngressPrioMappingCOS Integer32

CmPrioMapV2PrioMappingCOSEntry  
SEQUENCE    
  cmPrioMapV2PrioMappingCOSIndex Integer32
  cmPrioMapV2PrioMappingCOSValue Integer32
  cmPrioMapV2PrioMappingCOSOuterTagPri Integer32
  cmPrioMapV2PrioMappingCOSInnerTagPri Integer32
  cmPrioMapV2PrioMappingEncapOuterTagPriority Integer32
  cmPrioMapV2PrioMappingEncapInnerTagPriority Integer32
  cmPrioMapV2PrioMappingEncapOuterDscpValue Integer32
  cmPrioMapV2PrioMappingDscpValue Integer32

CmPrioMapV2PrioMappingPriEntry  
SEQUENCE    
  cmPrioMapV2PrioMappingPriIndex Integer32
  cmPrioMapV2PrioMappingPriInPrio Integer32
  cmPrioMapV2PrioMappingPriPrioControl PrioMapControlType
  cmPrioMapV2PrioMappingPriXTagPrio Integer32
  cmPrioMapV2PrioMappingPriCOS Integer32

CmPrioMapV2ProfileAppliedObjEntry  
SEQUENCE    
  cmPrioMapV2ProfileAppliedObj VariablePointer

CmAccPortExtEntry  
SEQUENCE    
  cmAccPortExtMcastRateLimitEnabled TruthValue
  cmAccPortExtMcastRateLimitSpeedLo Unsigned32
  cmAccPortExtMcastRateLimitSpeedHi Unsigned32
  cmAccPortExtBcastRateLimitEnabled TruthValue
  cmAccPortExtBcastRateLimitSpeedLo Unsigned32
  cmAccPortExtBcastRateLimitSpeedHi Unsigned32
  cmAccPortExtCombinedRateLimitEnabled TruthValue
  cmAccPortExtCombinedRateLimitSpeedLo Unsigned32
  cmAccPortExtCombinedRateLimitSpeedHi Unsigned32
  cmAccPortExtRefPrioMapProfile VariablePointer

CmNetPortExtEntry  
SEQUENCE    
  cmNetPortExtMcastRateLimitEnabled TruthValue
  cmNetPortExtMcastRateLimitSpeedLo Unsigned32
  cmNetPortExtMcastRateLimitSpeedHi Unsigned32
  cmNetPortExtBcastRateLimitEnabled TruthValue
  cmNetPortExtBcastRateLimitSpeedLo Unsigned32
  cmNetPortExtBcastRateLimitSpeedHi Unsigned32
  cmNetPortExtCombinedRateLimitEnabled TruthValue
  cmNetPortExtCombinedRateLimitSpeedLo Unsigned32
  cmNetPortExtCombinedRateLimitSpeedHi Unsigned32
  cmNetPortExtRefPrioMapProfile VariablePointer

F3UsbWIFIDonglePortEntry  
SEQUENCE    
  f3UsbWIFIDonglePortIndex Integer32
  f3UsbWIFIDonglePortIfIndex InterfaceIndex
  f3UsbWIFIDonglePortEntityIndex PhysicalIndex
  f3UsbWIFIDonglePortAdminState AdminState
  f3UsbWIFIDonglePortOperationalState OperationalState
  f3UsbWIFIDonglePortSecondaryState SecondaryState
  f3UsbWIFIDonglePortSSID DisplayString
  f3UsbWIFIDonglePortPassword DisplayString
  f3UsbWIFIDonglePortEncryption WIFIEncryptionType
  f3UsbWIFIDonglePortIPAddress IpAddress
  f3UsbWIFIDonglePortwWIFIIPNetMask IpAddress
  f3UsbWIFIDonglePortWIFIDHCPRole DHCPType
  f3UsbWIFIDonglePortWIFIAllocatedIPFrom IpAddress
  f3UsbWIFIDonglePortWIFIAllocatedIPEnd IpAddress
  f3UsbWIFIDonglePortStorageType StorageType
  f3UsbWIFIDonglePortRowStatus RowStatus
  f3UsbWIFIDonglePortAccessdUsers DisplayString

Defined Values

cmFacilityMIB 1.3.6.1.4.1.2544.1.12.4
This module defines the Facility MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA Optical Networking.
MODULE-IDENTITY    

cmFacilityObjects 1.3.6.1.4.1.2544.1.12.4.1
OBJECT IDENTIFIER    

cmFacilityConformance 1.3.6.1.4.1.2544.1.12.4.2
OBJECT IDENTIFIER    

cmEthernetAccPortTable 1.3.6.1.4.1.2544.1.12.4.1.1
A list of entries corresponding to Ethernet Access Port Facilities for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetAccPortEntry

cmEthernetAccPortEntry 1.3.6.1.4.1.2544.1.12.4.1.1.1
A conceptual row in the cmEthernetAccPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetAccPortEntry  

cmEthernetAccPortIndex 1.3.6.1.4.1.2544.1.12.4.1.1.1.1
An integer index value used to uniquely identify this Ethernet Access Port within a card. Note that each Ethernet Access Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, cmEthernetAccPortIndex. From release 5.6CC zero value becomes valid. The zero value is used in Network Element level objects which contain cmEthernetAccPortIndex in the index which is not-applicable for these objects e.g. Pass-thru Flows, Shapers or Policers.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0 | 1..65535  

cmEthernetAccPortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.1.1.2
This object has the same value as ifIndex for Ethernet Access Port. An integer index value used to uniquely identify this Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

cmEthernetAccPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.1.1.3
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

cmEthernetAccPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.1.1.4
This object represents the Administrative State of the Ethernet Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmEthernetAccPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.1.1.5
This object represents the Operational State of the Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmEthernetAccPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.1.1.6
This object represents the Secondary State of the Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmEthernetAccPortMTU 1.3.6.1.4.1.2544.1.12.4.1.1.1.7
This object provides the MTU on the Ethernet Access Port. The object is made read-write for FSP150CC devices.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortMediaType 1.3.6.1.4.1.2544.1.12.4.1.1.1.8
This object represents the type of Ethernet Media on the Ethernet Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetMediaType  

cmEthernetAccPortConfigSpeed 1.3.6.1.4.1.2544.1.12.4.1.1.1.9
This object allows to configure the speed of the Ethernet Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetPortSpeed  

cmEthernetAccPortNegotiatedSpeed 1.3.6.1.4.1.2544.1.12.4.1.1.1.10
This object provides the negotiated speed of the Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  EthernetPortSpeed  

cmEthernetAccPortMDIXType 1.3.6.1.4.1.2544.1.12.4.1.1.1.11
This object allows management of MDIX property on Ethernet Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetMDIXType  

cmEthernetAccPortJumboFramesEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.12
This object allows enabling/disabling jumbo frames support on the Ethernet Access Port. This object is only applicable for Ethernet Access Port on R3.1CM NTU Card.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortSfpVendorName 1.3.6.1.4.1.2544.1.12.4.1.1.1.13
This object provides the vendor name of the SFP. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

cmEthernetAccPortSfpPartNumber 1.3.6.1.4.1.2544.1.12.4.1.1.1.14
This object provides the part number of the SFP. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

cmEthernetAccPortSfpSerialNumber 1.3.6.1.4.1.2544.1.12.4.1.1.1.15
This object provides the serial number of the SFP. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

cmEthernetAccPortSfpDateOfManufacture 1.3.6.1.4.1.2544.1.12.4.1.1.1.16
This object provides the date of manufacture of the SFP. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

cmEthernetAccPortSfpConnectorValue 1.3.6.1.4.1.2544.1.12.4.1.1.1.17
This object provides the SFP connector value. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  SfpConnectorValue  

cmEthernetAccPortInitiateDiag 1.3.6.1.4.1.2544.1.12.4.1.1.1.18
This object allows to initiate Etherjack diagnosis on the Ethernet Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetDiagAction  

cmEthernetAccPortDiagnosePair1Cond 1.3.6.1.4.1.2544.1.12.4.1.1.1.19
This object provides diagnosis results for the cable Pair 1 on Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetAccPortDiagnosePair2Cond 1.3.6.1.4.1.2544.1.12.4.1.1.1.20
This object provides diagnosis results for the cable Pair 2 on Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetAccPortDiagnosePair3Cond 1.3.6.1.4.1.2544.1.12.4.1.1.1.21
This object provides diagnosis results for the cable Pair 3 on Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetAccPortDiagnosePair4Cond 1.3.6.1.4.1.2544.1.12.4.1.1.1.22
This object provides diagnosis results for the cable Pair 4 on Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetAccPortDiagnoseAutoNegCond 1.3.6.1.4.1.2544.1.12.4.1.1.1.23
This object provides auto negotiation results of the diagnosis test on Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagAutoNegCondType  

cmEthernetAccPortDiagnoseLpbkCond 1.3.6.1.4.1.2544.1.12.4.1.1.1.24
This object provides port loopback results of the diagnosis test on Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagLpbkCondType  

cmEthernetAccPortDiagnoseEfmLpbkCond 1.3.6.1.4.1.2544.1.12.4.1.1.1.25
This object provides remote EFM loopback results of the diagnosis test on Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagEfmOamLpbkCondType  

cmEthernetAccPortDiagnoseResult 1.3.6.1.4.1.2544.1.12.4.1.1.1.26
This object provides results of the diagnosis test in string form on Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

cmEthernetAccPortDiagnoseTestStatus 1.3.6.1.4.1.2544.1.12.4.1.1.1.27
This object provides the current status of the diagnosis test on Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagTestStatus  

cmEthernetAccPortDiagnoseTestTime 1.3.6.1.4.1.2544.1.12.4.1.1.1.28
This object provides the time when diagnosis test was last executed.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

cmEthernetAccPortLoopbackConfig 1.3.6.1.4.1.2544.1.12.4.1.1.1.29
This object allows to initiate loopbacks on on the Ethernet Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmLoopbackType  

cmEthernetAccPortLoopbackStatus 1.3.6.1.4.1.2544.1.12.4.1.1.1.30
This object provides status of the current loopback on the Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmLoopbackType  

cmEthernetAccPortLoopbackTime 1.3.6.1.4.1.2544.1.12.4.1.1.1.31
This object allows to specify time for timed-loopbacks on on the Ethernet Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..300  

cmEthernetAccPortLoopbackSwapSADA 1.3.6.1.4.1.2544.1.12.4.1.1.1.32
This object allows to specify whether or not the loopbacked frame will have the Source Address and Destination Address swapped.
Status: current Access: read-write
OBJECT-TYPE    
  CmSwapSADAType  

cmEthernetAccPortOuterVlanLoopbackMask 1.3.6.1.4.1.2544.1.12.4.1.1.1.33
This object allows specification of the outer VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Outer VLAN 1 Loopback Enabled 2 Outer VLAN 2 Loopback Enabled 4 Outer VLAN 3 Loopback Enabled Value of 0 means that no VLANs are enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

cmEthernetAccPortOuterVlanLoopback1 1.3.6.1.4.1.2544.1.12.4.1.1.1.34
This object allows specification of the outer VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetAccPortOuterVlanLoopback2 1.3.6.1.4.1.2544.1.12.4.1.1.1.35
This object allows specification of the outer VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetAccPortOuterVlanLoopback3 1.3.6.1.4.1.2544.1.12.4.1.1.1.36
This object allows specification of the outer VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetAccPortInnerVlanLoopbackMask 1.3.6.1.4.1.2544.1.12.4.1.1.1.37
This object allows specification of the inner VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Inner VLAN 1 Loopback Enabled 2 Inner VLAN 2 Loopback Enabled 4 Inner VLAN 3 Loopback Enabled Value of 0 means that no VLANs are enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

cmEthernetAccPortInnerVlanLoopback1 1.3.6.1.4.1.2544.1.12.4.1.1.1.38
This object allows specification of the inner VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetAccPortInnerVlanLoopback2 1.3.6.1.4.1.2544.1.12.4.1.1.1.39
This object allows specification of the inner VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetAccPortInnerVlanLoopback3 1.3.6.1.4.1.2544.1.12.4.1.1.1.40
This object allows specification of the inner VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetAccPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetAccPortLinkLossFwdEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.41
This object allows enabling/disabling link loss forwarding on the Ethernet Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortLinkLossFwdSignalType 1.3.6.1.4.1.2544.1.12.4.1.1.1.42
This object allows definition of the link loss forwarding signalling type. This is applicable only if cmEthernetAccPortLinkLossFwdEnabled is enabled. This object is applicable only for FSP150CM Release 3.1. This object is deprecated henceforth. Link Loss signalling will be supported using the object cmEthernetAccPortLinkLossFwdTxActionType.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmLinkLossFwdSignalType  

cmEthernetAccPortLinkLossFwdTriggerTypes 1.3.6.1.4.1.2544.1.12.4.1.1.1.43
This object allows definition of the link loss forwarding trigger types. This is applicable only if cmEthernetAccPortLinkLossFwdEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  CmLinkLossFwdTriggerTypes  

cmEthernetAccPortLinkLossFwdDelay 1.3.6.1.4.1.2544.1.12.4.1.1.1.44
This object allows specification of the delay between detection of link loss and signalling of link loss forwarding. Time specified is in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortLinkLossFwdActive 1.3.6.1.4.1.2544.1.12.4.1.1.1.45
This object provides the link loss forwarding status indicating if link loss forwarding is currently being signaled via the port.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortLinkLossFwdPartnerEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.46
This object provides the indication of a link partners ability to support link loss forwarding via EFM, i.e. from received organization specific OAMPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortLinkLossFwdLocalLinkId 1.3.6.1.4.1.2544.1.12.4.1.1.1.47
This object allows configuration of the Local Link Id on Ethernet access port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortLinkLossFwdRemoteLinkIds 1.3.6.1.4.1.2544.1.12.4.1.1.1.48
This object allows enabling/disabling Remote Link Ids on Ethernet access port. By setting the appropriate bit positions, the Ethernet access port is able to distinguish the remote side client ports from the Remote Link Down PDUs coming from remote end.
Status: current Access: read-write
OBJECT-TYPE    
  CmRemoteLinkIds  

cmEthernetAccPortOamId 1.3.6.1.4.1.2544.1.12.4.1.1.1.49
OAM Id. This is unique EFM OAM sublayer port id.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortOamAdminDisposition 1.3.6.1.4.1.2544.1.12.4.1.1.1.50
Ethernet Access Port's EFM OAM Disposition. This object is applicable only for FSP150CM Release 3.1. This object is deprecated henceforth. With FSP150CC Release 4.1, this property is managed using the Control Protocol Disposition tables.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortOamDiscoveryState 1.3.6.1.4.1.2544.1.12.4.1.1.1.51
Ethernet Access Port's OAM discovery state.
Status: current Access: read-only
OBJECT-TYPE    
  CmOamDiscoveryState  

cmEthernetAccPortOamLocalVarRtrvsEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.52
This object allows specification of whether the Ethernet Access Port supports sending variable response OAMPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortOamLocalLinkEventsEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.53
This object allows specification of whether the Ethernet Access Port supports interpreting Link Events.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortOamLocalOamLoopbacksSupported 1.3.6.1.4.1.2544.1.12.4.1.1.1.54
This object allows specification of whether the Ethernet Access Port is capable of OAM remote loopback mode.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortOamLocalUnidirSupportEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.55
This object allows specification of whether the Ethernet Access Port is capable of sending OAMPDUs when the receive path is non-operational.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortOamLocalMaxPDUSize 1.3.6.1.4.1.2544.1.12.4.1.1.1.56
This object represents the largest OAMPDU, in octets, supported by the Ethernet Access Port. This value is compared to the remote Maximum PDU Size and the smaller of the two is used.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortOamLocalMode 1.3.6.1.4.1.2544.1.12.4.1.1.1.57
This object allows to configure the OAM sublayer entity in either Active or Passive mode.
Status: current Access: read-write
OBJECT-TYPE    
  CmOamMode  

cmEthernetAccPortOamRemoteMacAddress 1.3.6.1.4.1.2544.1.12.4.1.1.1.58
This object allows retrieval of the Remote Mac Address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cmEthernetAccPortOamRemoteVarRtrvsEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.59
This object allows retrieval of whether the remote OAM entity supports sending variable response OAMPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortOamRemoteLinkEventsEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.60
This object allows retrieval of whether the remote OAM entity supports interpreting Link Events.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortOamRemoteOamLoopbacksSupported 1.3.6.1.4.1.2544.1.12.4.1.1.1.61
This object allows retrieval of whether the remote OAM entity supports OAM remote loopback mode.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortOamRemoteUnidirSupportEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.62
This object allows retrieval of whether the remote OAM entity is capable of sending OAMPDUs when the receive path is non-operational.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortOamRemoteMaxPDUSize 1.3.6.1.4.1.2544.1.12.4.1.1.1.63
This object allows retrieval of the remote OAM entity maximum OAMPDU size.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortOamRemoteMode 1.3.6.1.4.1.2544.1.12.4.1.1.1.64
This object allows to retrieve whether the remote OAM sublayer entity is either in Active or Passive mode.
Status: current Access: read-only
OBJECT-TYPE    
  CmOamMode  

cmEthernetAccPortMode 1.3.6.1.4.1.2544.1.12.4.1.1.1.65
This object allows specification of whether the Ethernet Access Port is in a connection-oriented (offering VLAN based services) mode or connection-less (offering MAC based services) mode.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetSvcPortMode  

cmEthernetAccPortSvcType 1.3.6.1.4.1.2544.1.12.4.1.1.1.66
This object allows specification of whether the Ethernet Access Port provides transparent port based services, or multi-flow VLAN based services.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetSvcType  

cmEthernetAccPortRxPauseDisposition 1.3.6.1.4.1.2544.1.12.4.1.1.1.67
This object allows management of RX pause frames on Ethernet Access port. This object is applicable only for FSP150CM Release 3.1. This object is deprecated henceforth. With FSP150CC Release 4.1, this property is managed using the Control Protocol Disposition tables.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortTxPauseEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.68
This object allows enabling/disabling transmit pause frames on Ethernet Access port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortAfpType 1.3.6.1.4.1.2544.1.12.4.1.1.1.69
This object allows specification of the Acceptable Frame Policy on Ethernet Access port. Users can specify whether the port supports only tagged frames, only untagged frames or both tagged and untagged frames.
Status: current Access: read-write
OBJECT-TYPE    
  CmAfpType  

cmEthernetAccPortMDIXStatus 1.3.6.1.4.1.2544.1.12.4.1.1.1.70
This object provides the current MDIX status of the Ethernet Access port.
Status: current Access: read-only
OBJECT-TYPE    
  CmEthernetMDIXType  

cmEthernetAccPortSfpReach 1.3.6.1.4.1.2544.1.12.4.1.1.1.71
This object provides the SFP Reach in meters. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortSfpLaserWaveLength 1.3.6.1.4.1.2544.1.12.4.1.1.1.72
This object provides the SFP Laser Wave Length in nano meters. This is applicable only when cmEthernetAccPortMediaType is fiber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortSfpMediaType 1.3.6.1.4.1.2544.1.12.4.1.1.1.73
This object provides the SFP Media Type. This is applicable when cmEthernetAccPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  SfpMediaType  

cmEthernetAccPortOamEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.74
This object allows to manage the EFM OAM on Ethernet Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortOamAdminState 1.3.6.1.4.1.2544.1.12.4.1.1.1.75
This object provides the EFM OAM Admin State.
Status: current Access: read-only
OBJECT-TYPE    
  CmOamAdminState  

cmEthernetAccPortShapingEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.76
This object allows to manage the Access Port Shaping. When enabled, values in cmEthernetAccPortShapedSpeedLo and cmEthernetAccPortShapedSpeedHi are applicable.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortShapedSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.1.1.77
This object allows to specify the lower 32 bits of the Access Port Shaped speed. This value is applicable when cmEthernetAccPortShapingEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmEthernetAccPortShapedSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.1.1.78
This object allows to specify the higher 32 bits of the Access Port Shaped speed. This value is applicable when cmEthernetAccPortShapingEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmEthernetAccPortQinQEtherType 1.3.6.1.4.1.2544.1.12.4.1.1.1.79
This object allows to specify the Q-in-Q Ether Type on the Access Port. Setting this value to 0 will disable the Q-in-Q override on the Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmEthernetAccPortRxPauseEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.80
This object allows to enable/disable the RX PAUSE on the Access Port. This object is not applicable for FSP150CM NTU Card. On NTU Card cmEthernetAccPortRxPauseDisposition object should be used to provision RxPause disposition.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortAutoDiagEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.81
This object allows to enable or disable the automatic Cable Diagnostic tests when the cable is removed from the port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortLinkLossFwdTxActionType 1.3.6.1.4.1.2544.1.12.4.1.1.1.82
This object allows to specify the Access Port's behavior when link loss forwarding trigger events occur on the Network Port. This provides ability to configure per access port LLF behavior.
Status: current Access: read-write
OBJECT-TYPE    
  CmLinkLossFwdTxActionType  

cmEthernetAccPortLinkLossFwdRxRLDLinkIds 1.3.6.1.4.1.2544.1.12.4.1.1.1.83
This object provides the received Remote Link IDs in EFM RLD messages on the Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmRemoteLinkIds  

cmEthernetAccPortN2AVlanTrunkingEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.84
This object allows to enable or disable the VLAN trunking on Ethernet Access port. Disabling VLAN trunking removes all VLAN tags before transmitting traffic out of the access port. This object is only applicable for connection-oriented, evpl service type.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortA2NPushPVIDEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.85
This object allows to specify whether cmEthernetAccPortPortVlanId value will be PUSHed on untagged frames or not in the Access to Network direction. This object is only applicable for connection-oriented, evpl service type.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortN2APopPVIDEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.86
This object allows to specify whether cmEthernetAccPortPortVlanId value will be POPed in the Network to Access direction. This object is only applicable for connection-oriented, evpl service type.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortPortVlanId 1.3.6.1.4.1.2544.1.12.4.1.1.1.87
This object allows to specify the Ethernet Access Port VLAN Id to PUSH on untagged frames in the Access to Network direction. This object is only applicable for connection-oriented, evpl service type, when cmEthernetAccPortA2NPushPVIDEnabled is set to true.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

cmEthernetAccPortPortVlanPriority 1.3.6.1.4.1.2544.1.12.4.1.1.1.88
This object allows to specify the Ethernet Access Port VLAN Priority for the PUSHed VLAN tag (specified by cmEthernetAccPortPortVlanId) on untagged frames in the Access to Network direction. This object is only applicable for connection-oriented, evpl service type, when cmEthernetAccPortA2NPushPVIDEnabled is set to true.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmEthernetAccPortPrioMapMode 1.3.6.1.4.1.2544.1.12.4.1.1.1.89
This object allows to specify the Ethernet Access Port Priority Mapping Mode used for classification of frames. This object is only applicable for connection-oriented, evpl service type.
Status: current Access: read-write
OBJECT-TYPE    
  PriorityMapMode  

cmEthernetAccPortSyncEEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.90
This object allows to specify whether the Ethernet Access Port can be enabled/disabled for Synchronous Ethernet. This object is only applicable for Synchronous Ethernet capable ports. When enabled, on receive side -port can extract the frequency of its input signal and pass the recovered clock to the system clock -port processes the ESMC(Ethernet Synchronization Messaging Channel) and extracts the QL (when also QL enabled) -port is eligible to be selected as a system clock reference When enabled, on transmit side -port's transmit clock is locked to the system clock -port generates an ESMC to generate a QL (when also QL enabled) When disabled, on receive side, -port does not pass the recovered clock to the system clock -port does not process the ESMC (if present) -port is not eligible to be selected as a system clock reference When disabled, on transmit side -port's output frequency may be synchronized to the system clock -port does not generate an ESMC.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortQLModeEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.91
This object allows to specify whether the Ethernet Access Port can be enabled/disabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetAccPortQLModeEnabled is set to true. When enabled, on receive side -port shall PEER the SSM (Sync Status Messages) slow protocol PDUs and take appropriate action When enabled, on transmit side -port shall periodically (once a second) transmit QL TLV information PDUs When disabled, on receive side, -port shall terminate and discard any SSM slow protocol PDUs When disabled, on transmit side -port shall not transmit any SSM slow protocol PDUs.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortExpectedQL 1.3.6.1.4.1.2544.1.12.4.1.1.1.92
This object allows to specify the expected QL when the Ethernet Access Port is enabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetAccPortQLModeEnabled is set to true. This object allows the user to set a minimum expected received Quality Level on the port. The valid values depend upon the SYNC entity's Network Clock Type. A value of None represents that a minimum Quality Level is not expected. The default value shall be None.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetAccPortAssumedQL 1.3.6.1.4.1.2544.1.12.4.1.1.1.93
This object allows to specify the assumed QL on the Ethernet Access Port. This object is only applicable for Synchronous Ethernet capable ports. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port's QL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetAccPortReceivedQL 1.3.6.1.4.1.2544.1.12.4.1.1.1.94
This object provides the Received QL value for the Ethernet port. If the Ethernet port's QL Mode is disabled, then the received QL value is not applicable.This object is only applicable for Synchronous Ethernet capable ports.
Status: current Access: read-only
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetAccPortTransmitQL 1.3.6.1.4.1.2544.1.12.4.1.1.1.95
This object provides the Transmitted QL value for the Ethernet port. If the Ethernet port's QL Mode is disabled, then the received QL value is not applicable. This object is only applicable for Synchronous Ethernet capable ports.
Status: current Access: read-only
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetAccPortDeiEnable 1.3.6.1.4.1.2544.1.12.4.1.1.1.96
This is a port level control to reset the DEI (Drop Eligibility Indicator) bit in the S-Tag, if the downstream equipment supports S-Tag TPID (EtherType) but cannot handle DEI bit set. In the receive direction, it uses the S-TAG DEI when enabled, else ignores it. The following comment is NOT relevant to OSA8.1.1, since this object is still supported by OSA8.1.1. The object has been deprecated. The respective configuration should be managed by following objects: cmEthernetAccPortRxDeiAction, cmEthernetAccPortTxDeiAction, cmEthernetAccPortRxDeiOuterTagType, cmEthernetAccPortTxDeiOuterTagType.
Status: deprecated Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortPcpDEEncType 1.3.6.1.4.1.2544.1.12.4.1.1.1.97
This is a port level control that specifies the mode of drop eligibility encoding in PCP bits of the VLAN tag.
Status: current Access: read-write
OBJECT-TYPE    
  PcpDEEncType  

cmEthernetAccPortPcpDEPairsAction 1.3.6.1.4.1.2544.1.12.4.1.1.1.98
This object allows the SNMP user to manage the Priority Code Point (PCP) Drop Eligibility Pairs. When the cmEthernetAccPortPcpDEEncType is of type 7p1d, 6p2d, 5p3d, the cmAccPortPcpDEPairTable can be used to specify alternate pairs of priorities to specify drop eligibility/ ineligibility.
Status: current Access: read-write
OBJECT-TYPE    
  PcpDEPairsAction  

cmEthernetAccPortSSMRemoteMacAddress 1.3.6.1.4.1.2544.1.12.4.1.1.1.99
This object allows retrieval of the Remote Mac Address, when the port is peering using SSM.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cmEthernetAccPortXgePhyType 1.3.6.1.4.1.2544.1.12.4.1.1.1.100
This object allows to specify the PHY type of 10G Ethernet Port. 10G ports can operate in LAN-PHY or WAN-PHY mode. The default mode is LAN-PHY and port rate in this mode is 10Gbps. In WAN-PHY mode the port rate is 9.29Gbps. This attribute is only applicable for ports configured to work at speed-10G-full. For other speeds the value of this object must be 'not-applicable' and cannot be changed.
Status: current Access: read-write
OBJECT-TYPE    
  XgePhyType  

cmEthernetAccPortLoopbackSourceMacControlEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.101
This object allows to Enable/Disable the Acc Port Source MAC Address frame matching criteria for all streams. Not applicable for: efm-oam-remote, efm-oam-remote-timed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortLoopbackDestMacControlEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.102
This object allows to Enable/Disable the Acc Port Destination MAC Address frame matching criteria for all streams. Not applicable for: efm-oam-remote, efm-oam-remote-timed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortLoopbackSourceMacAddress 1.3.6.1.4.1.2544.1.12.4.1.1.1.103
This object allows to set Acc Port Source MAC Address for frame matching when Acc Port Source MAC Control is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmEthernetAccPortLoopbackDestMacAddress 1.3.6.1.4.1.2544.1.12.4.1.1.1.104
This object allows to set Acc Port Destination MAC Address for frame matching when Acc Port Destination MAC Control is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmEthernetAccPortLoopbackBlockingEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.105
This object allows frame blocking when loopback is active. - True: Blocks frames in the non-loopback direction that match the PORT or VLAN received in the non-loopback direction. Discards frames in the loopback direction that match the PORT or VLAN, but do not match the MAC address criteria, - False: No blocking of frames.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortRxDeiAction 1.3.6.1.4.1.2544.1.12.4.1.1.1.106
This object allows to specify the Receive DEI Action.
Status: current Access: read-write
OBJECT-TYPE    
  RxDeiAction  

cmEthernetAccPortTxDeiAction 1.3.6.1.4.1.2544.1.12.4.1.1.1.107
This object allows to specify the Transmit DEI Action.
Status: current Access: read-write
OBJECT-TYPE    
  TxDeiAction  

cmEthernetAccPortRxDeiOuterTagType 1.3.6.1.4.1.2544.1.12.4.1.1.1.108
This object allows to specify the Receive DEI Outer Tag Type.
Status: current Access: read-write
OBJECT-TYPE    
  DeiOuterTagType  

cmEthernetAccPortTxDeiOuterTagType 1.3.6.1.4.1.2544.1.12.4.1.1.1.109
This object allows to specify the Transmit DEI Outer Tag Type.
Status: current Access: read-write
OBJECT-TYPE    
  DeiOuterTagType  

cmEthernetAccPortLaserWDMChannel 1.3.6.1.4.1.2544.1.12.4.1.1.1.110
Channel number of WDM tunable XFP setting.
Status: current Access: read-write
OBJECT-TYPE    
  SfpChannelIdentifier  

cmEthernetAccPortLaserIsTunable 1.3.6.1.4.1.2544.1.12.4.1.1.1.111
Channel number of WDM tunable XFP setting.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortLaserFrequency 1.3.6.1.4.1.2544.1.12.4.1.1.1.112
Channel number of WDM tunable XFP setting.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cmEthernetAccPortMediaTypeAutoSelected 1.3.6.1.4.1.2544.1.12.4.1.1.1.113
This object provides the auto selected Ethernet Media of the Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  EthernetMediaType  

cmEthernetAccPortLowLatencyQueuingEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.114
This object allows to Enable/Disable the Low Latency Queuing on the Ethernet Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortA2nSwapPriorityVIDEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.115
This object allows to Enable/Disable the Swapping of Priority Vlan Id in the A2N direction.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortN2aSwapPriorityVIDEnabled 1.3.6.1.4.1.2544.1.12.4.1.1.1.116
This object allows to Enable/Disable the Swapping of Priority Vlan Id in the N2A direction.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortSwapPriorityVID 1.3.6.1.4.1.2544.1.12.4.1.1.1.117
This object allows to specify the value of Vlan Id for the Swapping of Priority Vlan Id operation for both the A2N and N2A direction.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

cmEthernetAccPortDiagnosticMacAddress 1.3.6.1.4.1.2544.1.12.4.1.1.1.118
This object describes the diagnose mac address for SAT, ECPA, JDSU, Loopback with Override SA etc.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cmEthernetAccPortIngressCOSPriority 1.3.6.1.4.1.2544.1.12.4.1.1.1.119
Indicates which VLAN tag to use for PCP Priority to COS mapping when the port Priority Map Mode is 802.1p. Supported values are inner-vlantag and outer-vlantag. This attribute is only applicable on products when Flowpoint Model is supported. inner-vlantag: The inner VLAN tag PCP Priority of a frame is used for ingress COS mapping. A frame with no inner VLAN tag (untagged or single-tagged) will have a COS equal to the default COS of the port. outer-vlantag: The outer VLAN tag PCP Priority of a frame is used for ingress COS mapping. A frame with no outer VLAN tag (untagged) will have a COS equal to the default COS of the port. This attribute has been deprecated and is not supported. Now, the Priority Map Mode indicates whether it is inner or outer. Use priomap-8021p(4) for outer and priomap-8021p-inner(5) for inner.
Status: deprecated Access: read-write
OBJECT-TYPE    
  VlanTagType  

cmEthernetAccPortDefaultCOS 1.3.6.1.4.1.2544.1.12.4.1.1.1.120
The COS assigned to a frame that does not have a valid COS identifier for the Priority Map Mode of the port. This attribute is only applicable on products when Flowpoint Model is supported. This value is assigned to a frame received on a port when: - the cmEthernetAccPortPrioMapMode=priomap-8021p, ingressCOSPriority=inner-vlantag; and the frame is untagged - the cmEthernetAccPortPrioMapMode=priomap-8021p, ingressCOSPriority=inner-vlantag; and the frame has a single VLAN tag - the cmEthernetAccPortPrioMapMode=priomap-8021p, ingressCOSPriority=outer-vlantag; and the frame is untagged - the cmEthernetAccPortPrioMapMode=priomap-dscp; and the frame does not have an IP ethertype - the cmEthernetAccPortPrioMapMode=priomap-tos; and the frame does not have an IP ethertype. This attribute has been deprecated and is not supported. The Default COS is determined from the flowpoint's associated Priority Mapping Profle.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmEthernetAccPortTrafficModel 1.3.6.1.4.1.2544.1.12.4.1.1.1.121
The Traffic Management connection model available for the port. - accessFlow: NID Traffic Connection model. - flowpoint: Multipoint and Aggregation Traffic Connection model.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetPortTrafficModel  

cmEthernetAccPortCpdTable 1.3.6.1.4.1.2544.1.12.4.1.2
A list of entries corresponding to Ethernet Access Port Control Protocol Disposition. This table is only applicable for FSP150CM Hub Shelf Release 3.x.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetAccPortCpdEntry

cmEthernetAccPortCpdEntry 1.3.6.1.4.1.2544.1.12.4.1.2.1
A conceptual row in the cmEthernetAccPortCpdTable. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Access Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetAccPortCpdEntry  

cmEthernetAccPortCpdIndex 1.3.6.1.4.1.2544.1.12.4.1.2.1.1
An arbitrary integer index value used to uniquely identify this CPD Service Entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

cmEthernetAccPortCpdFilterType 1.3.6.1.4.1.2544.1.12.4.1.2.1.2
This enables specification of type of CPD Filter.
Status: current Access: read-only
OBJECT-TYPE    
  CmControlProtocolFilterType  

cmEthernetAccPortCpdFilterDescr 1.3.6.1.4.1.2544.1.12.4.1.2.1.3
This provides description of CPD Filter.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

cmEthernetAccPortCpdDispType 1.3.6.1.4.1.2544.1.12.4.1.2.1.4
This enables specification of disposion type of CPD Filter.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdMacAddressMatch 1.3.6.1.4.1.2544.1.12.4.1.2.1.5
This enables provides the Filter MAC Address to match.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmEthernetAccPortCpdMacAddressMask 1.3.6.1.4.1.2544.1.12.4.1.2.1.6
This enables provides the Filter MAC Address Mask to match.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmEthernetAccPortCpdEthertype 1.3.6.1.4.1.2544.1.12.4.1.2.1.7
This enables provides the Filter Ethertype to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cmEthernetAccPortCpdEthertypeMask 1.3.6.1.4.1.2544.1.12.4.1.2.1.8
This enables provides the Filter Ethertype Mask to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortCpdSubtype 1.3.6.1.4.1.2544.1.12.4.1.2.1.9
This enables provides the Filter Subtype to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortCpdSubtypeMask 1.3.6.1.4.1.2544.1.12.4.1.2.1.10
This enables provides the Filter Subtype Mask to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortClbTable 1.3.6.1.4.1.2544.1.12.4.1.3
A list of entries corresponding to Ethernet Access Port Cable Length Benchmark.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetAccPortClbEntry

cmEthernetAccPortClbEntry 1.3.6.1.4.1.2544.1.12.4.1.3.1
A conceptual row in the cmEthernetAccPortClbTable. These entries represent Cable Length Benchmarks on the Ethernet Access Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetAccPortClbEntry  

cmEthernetAccPortClbIndex 1.3.6.1.4.1.2544.1.12.4.1.3.1.1
An integer index value used to uniquely identify this Cable Length Benchmark Entry specification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..5  

cmEthernetAccPortClbEnabled 1.3.6.1.4.1.2544.1.12.4.1.3.1.2
This enables specification of Cable Length Benchmark entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortClbLength 1.3.6.1.4.1.2544.1.12.4.1.3.1.3
Cable length of Cable Points Entry. The cable length is of the form XXX[.YY] where XX can be any integer value and YY allows precision of 2 decimals after the floating point. Note that .YY is optional.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cmEthernetAccPortClbDescr 1.3.6.1.4.1.2544.1.12.4.1.3.1.4
A textual string containing description of cable span.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

cmFlowTable 1.3.6.1.4.1.2544.1.12.4.1.4
A list of entries corresponding to Ethernet Flows for configuration purposes. If the corresponding Ethernet Access Port's cmEthernetAccPortMode is connection-oriented and cmEthernetAccPortSvcType is epl, there exists a single Flow in this table. No Flow creation or deletion is allowed on this table for FSP150CM NTU based services. Since Fsp150 R5.6CC release this table is used to manage 2 types of Flows: - Access Port Flow as in the previous releases - Tranparent Flow (new in 5.6CC) A Transparent Flow is Flow between Network-1 and Network-2 ports used to convey pass-thru traffic in the ring topology e.g. ERP. Few of the existing attributes will have new semantix for Transperent Flow. Transparent Flow is a NE level object and hence has different indexing than the Access Port Flow. The valid indices are neIndex and cmFlowIndex. The remaining indices will have constant values as follows: shelfIndex = 1 slotIndex = 255 cmEthernetAccPortIndex = 0
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmFlowEntry

cmFlowEntry 1.3.6.1.4.1.2544.1.12.4.1.4.1
A conceptual row in the cmFlowTable. These entries represent an Ethernet Flow.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmFlowEntry  

cmFlowIndex 1.3.6.1.4.1.2544.1.12.4.1.4.1.1
The integer index value corresponding to an Ethernet Flow.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..400  

cmFlowCircuitName 1.3.6.1.4.1.2544.1.12.4.1.4.1.2
This object allows SNMP management entities to provide a circuit identifier with the Flow.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..256)  

cmFlowAdminState 1.3.6.1.4.1.2544.1.12.4.1.4.1.3
This object represents the Administrative State of the Flow.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmFlowOperationalState 1.3.6.1.4.1.2544.1.12.4.1.4.1.4
This object represents the Operational State of the Flow.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmFlowSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.4.1.5
This object represents the Secondary State of the Flow.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmFlowType 1.3.6.1.4.1.2544.1.12.4.1.4.1.6
This object represents the type of the Flow.
Status: current Access: read-create
OBJECT-TYPE    
  CmFlowType  

cmFlowMultiCOS 1.3.6.1.4.1.2544.1.12.4.1.4.1.7
This object allows specification of multiple COS (Class of Service) Flow.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowA2NCIR 1.3.6.1.4.1.2544.1.12.4.1.4.1.8
This object represents the Commited Information Rate(CIR) of an Flow in the Access to Network (A2N) direction. For a portbased Flow(FSP150CM NTU, CPMR), this object is not settable. This value represents the lower 32-bits of the CIR. For a Multi COS flow, this value is settable only at creation time. In case of Tranparent Flow this object represents N1 to N2 CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmFlowA2NEIR 1.3.6.1.4.1.2544.1.12.4.1.4.1.9
This object represents the Excess Information Rate(EIR) on an Flow in the Access to Network (A2N) direction. For a portbased Flow(FSP150CM NTU, CPMR), this object is not settable. This value represents the lower 32-bits of the CIR. For a Multi COS flow, this value is settable only at creation time. In case of Tranparent Flow this object represents N1 to N2 EIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmFlowN2ARateLimitingEnabled 1.3.6.1.4.1.2544.1.12.4.1.4.1.10
This object allows management of the N2A rate limiting, independent of A2N rate limiting. When not enabled, N2A specification is the same as A2N. This object is not applicable for Tranparent Flow; the value should be FALSE.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowN2ACIR 1.3.6.1.4.1.2544.1.12.4.1.4.1.11
This object represents the Commited Information Rate(CIR) of an Flow in the Network to Access (N2A) direction. For a portbased Flow, this object is not settable. This is only settable if cmFlowN2ARateLimitingEnabled is enabled. In case of Tranparent Flow this object represents N2 to N1 CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmFlowN2AEIR 1.3.6.1.4.1.2544.1.12.4.1.4.1.12
This object represents the Excess Information Rate(CIR) of an Flow in the Network to Access (N2A) direction. For a portbased Flow, this object is not settable. This is only settable if cmFlowN2ARateLimitingEnabled is enabled. In case of Tranparent Flow this object represents N2 to N1 EIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmFlowStorageType 1.3.6.1.4.1.2544.1.12.4.1.4.1.13
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmFlowRowStatus 1.3.6.1.4.1.2544.1.12.4.1.4.1.14
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmFlowRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmFlowRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmFlowRowStatus object may be modified if the associated instance of this object is equal to active(1). Note that flow creation and deletion is only supported with access port in connection-oriented evpl mode.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmFlowTrafficType 1.3.6.1.4.1.2544.1.12.4.1.4.1.15
This object provides information on the type of traffic flow supported by the system, i.e.'shaped-only' flows (support only shaping) or 'policed-shaped' (support policing and shaping) flows. 'shaped-only' flow exists for FSP150CM NTU and CPMR access ports. 'policed-shaped' flows are supported in FSP150CC devices. Please note that this object refers to how traffic profiles are managed on devices and is independent of the policing enabling/disabling feature.
Status: current Access: read-only
OBJECT-TYPE    
  FlowTrafficType  

cmFlowCOS 1.3.6.1.4.1.2544.1.12.4.1.4.1.16
This object allows specification of the COS (Class of Service) value for the Traffic Flow. This value is used at flow creation time to identify the COS level of the A2N and N2A shaper. In case of a multi-COS flow, this value is not applicable when multiple policers/shapers exist on the flow. This object is also applicable to specify the COS of a connection-oriented epl service.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

cmFlowVlanMemberList 1.3.6.1.4.1.2544.1.12.4.1.4.1.17
This object is applicable only when Port is in connection-oriented evpl mode. This attribute is mandatory if creation of connection-oriented evpl regular flow is desired. It allows specification of VLAN members of the Flow. VLAN members are comma separated, of the form X-Y where X is the VLAN Id and Y is the VLAN Priority. VLAN members can be of the form X-* or X (vlan X with all priorities), *-Y (all vlans with priority Y), and X1:X2 (range of vlans from X1 to X2, all priorities). Members with specific VLAN Id and specific VLAN Priority are not supported. Once the flow is created, this attribute can only be updated using cmFlowAction and cmFlowActionVlan objects.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..512)  

cmFlowAction 1.3.6.1.4.1.2544.1.12.4.1.4.1.18
This object is applicable only when Port is in connection-oriented evpl mode and the cmFlowType is regular. This object allows to add or remove the VLAN members specified by cmFlowActionVlan object. SNMP manager must first configure the VLAN member to be added/removed in the object cmFlowActionVlan and then should specify cmFlowAction on whether to add/remove the specified VLAN member.
Status: current Access: read-write
OBJECT-TYPE    
  FlowVlanActionType  

cmFlowActionVlan 1.3.6.1.4.1.2544.1.12.4.1.4.1.19
This object is applicable only when Port is in connection-oriented evpl mode. This object allows adding/removing VLAN members to a connection-oriented evpl regular flow. VLAN member is of the form X-Y where X is the VLAN Id and Y is the VLAN Priority. VLAN members can be of the form X-* (vlan X with all priorities), *-Y (all vlans with priority Y), and X1:X2 (range of vlans from X1 to X2, all priorities). Members with specific VLAN Id and specific VLAN Priority are not supported. In order to add/remove VLAN member to a flow, user must specify this object with appropriate VLAN and then invoke cmFlowAction.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..16)  

cmFlowUntaggedMemberEnabled 1.3.6.1.4.1.2544.1.12.4.1.4.1.20
This object is applicable only when Port is in connection-oriented evpl mode for a regular flow as well as default flow. This object allows to specify whether or not the flow supports untagged traffic.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowA2NCIRHi 1.3.6.1.4.1.2544.1.12.4.1.4.1.21
This object represents the Commited Information Rate(CIR) of an Flow in the Access to Network (A2N) direction. This value represents the upper 32 bits of CIR (lower is provided in cmFlowA2NCIR). For a Multi COS flow, this value is settable only at creation time. In case of Tranparent Flow this object represents N1 to N2 CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmFlowA2NEIRHi 1.3.6.1.4.1.2544.1.12.4.1.4.1.22
This object represents the Excess Information Rate(EIR) on an Flow in the Access to Network (A2N) direction. For a portbased Flow(FSP150CM NTU, CPMR), this object is not settable. This value represents the higher 32-bits of the CIR. For a Multi COS flow, this value is settable only at creation time. In case of Tranparent Flow this object represents N1 to N2 EIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmFlowN2ACIRHi 1.3.6.1.4.1.2544.1.12.4.1.4.1.23
This object represents the Commited Information Rate(CIR) of an Flow in the Network to Access (N2A) direction. This value represents the upper 32 bits of CIR (lower is provided in cmFlowN2ACIR). For a Multi COS flow, this value is settable only at creation time. This is only settable if cmFlowN2ARateLimitingEnabled is enabled. In case of Tranparent Flow this object represents N2 to N1 CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmFlowN2AEIRHi 1.3.6.1.4.1.2544.1.12.4.1.4.1.24
This object represents the Excess Information Rate(EIR) on an Flow in the Network to Access (N2A) direction. For a portbased Flow(FSP150CM NTU, CPMR), this object is not settable. This value represents the higher 32-bits of the CIR. For a Multi COS flow, this value is settable only at creation time. This is only settable if cmFlowN2ARateLimitingEnabled is enabled. In case of Tranparent Flow this object represents N2 to N1 EIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmFlowHCOSMgmtEnabled 1.3.6.1.4.1.2544.1.12.4.1.4.1.25
This object allows management of Hierarchical COS on the Flow.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowGuaranteedA2NBandwidthLo 1.3.6.1.4.1.2544.1.12.4.1.4.1.26
This object supports the Hierarchical Class of Service (HCOS) feature. It is only applicable for a flow with multiple class of services. This allows the provisioning of guaranteed bandwidth (lower 32 bits) of a flow. This value must be greater than or equal to the sum of all individual COS CIRs. In case of Tranparent Flow this object represents N1 to N2 and N2 to N1 guaranteed bandwidth.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowGuaranteedA2NBandwidthHi 1.3.6.1.4.1.2544.1.12.4.1.4.1.27
This object supports the Hierarchical Class of Service (HCOS) feature. It is only applicable for a flow with multiple class of services. This allows the provisioning of guaranteed bandwidth (upper 32 bits) of a flow. This value must be greater than or equal to the sum of all individual COS CIRs. In case of Tranparent Flow this object represents N1 to N2 and N2 to N1 guaranteed bandwidth.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowMaximumA2NBandwidthLo 1.3.6.1.4.1.2544.1.12.4.1.4.1.28
This object supports the Hierarchical Class of Service (HCOS) feature. It is only applicable for a flow with multiple class of services. This allows the provisioning of maximum bandwidth (lower 32 bits) of a flow. This is the peak limit of a flow. This value must be greater than or equal to the sum of all individual COS CIRs. In case of Tranparent Flow this object represents N1 to N2 and N2 to N1 maximum bandwidth.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowMaximumA2NBandwidthHi 1.3.6.1.4.1.2544.1.12.4.1.4.1.29
This object supports the Hierarchical Class of Service (HCOS) feature. It is only applicable for a flow with multiple class of services. This allows the provisioning of maximum bandwidth (upper 32 bits) of a flow. This is the peak limit of a flow. This value must be greater than or equal to the sum of all individual COS CIRs. In case of Tranparent Flow this object represents N1 to N2 and N2 to N1 maximum bandwidth.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowCTagControl 1.3.6.1.4.1.2544.1.12.4.1.4.1.30
This object allows specification of the tag management operation on the C-TAG. Supported types are 'push', 'pushvid', 'swapvid' and 'none'. If the type is 'push', the VLAN Id (cmFlowCTagVlanId) and priority (cmFlowCTagVlanPriority) are pushed onto the frame; if the type is 'pushvid', only the VLAN Id (12 bits) is pushed, the Priority is copied from incoming tag's priority; if the type is 'swapvid', only the VLAN Id (12 bits) are swapped with the specified cmFlowCTagVlanId; if the type is 'none', no C-TAG management is performed. This object is not applicable for Tranparent Flow; the value should be 'none'.
Status: current Access: read-create
OBJECT-TYPE    
  FlowTagControl  

cmFlowCTagVlanId 1.3.6.1.4.1.2544.1.12.4.1.4.1.31
This object allows specification of the VLAN Id to be pushed or swapped, based on the value of cmFlowCTagControl. It is applicable for 'push', 'swapvid' and 'pushvid' control types. This object is not applicable for Tranparent Flow; the value should be 0.
Status: current Access: read-create
OBJECT-TYPE    
  VlanId  

cmFlowCTagVlanPriority 1.3.6.1.4.1.2544.1.12.4.1.4.1.32
This object allows specification of the VLAN Priority to be pushed or swapped, based on the value of cmFlowCTagControl. It is applicable for 'push' control type. This object is not applicable for Tranparent Flow; the value should be 0.
Status: current Access: read-create
OBJECT-TYPE    
  VlanPriority  

cmFlowCTagMatchRxPrio 1.3.6.1.4.1.2544.1.12.4.1.4.1.33
This object is used to specify whether the C-TAG priority be used or ignored for traffic in the N2A direction. This is only applicable if cmFlowCTagControl is 'push'. This object is not applicable for Tranparent Flow; the value should be FALSE.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowSTagControl 1.3.6.1.4.1.2544.1.12.4.1.4.1.34
This object allows specification of the tag management operation on the S-TAG. Supported types are 'push', 'swapvid', and 'none'. If the type is 'push', the VLAN Id (cmFlowSTagVlanId) and priority (cmFlowSTagVlanPriority) are pushed onto the frame; if the type is 'swapvid', the VLAN Id(12 bits) is swapped with the specified cmFlowSTagVlanId; type is 'none', no S-TAG manament is performed. This object is not applicable for Tranparent Flow; the value should be 'none'.
Status: current Access: read-create
OBJECT-TYPE    
  FlowTagControl  

cmFlowSTagVlanId 1.3.6.1.4.1.2544.1.12.4.1.4.1.35
This object allows specification of the VLAN Id to be pushed, based on the value of cmFlowSTagControl. It is applicable for 'push' control type. This object is not applicable for Tranparent Flow; the value should be 0.
Status: current Access: read-create
OBJECT-TYPE    
  VlanId  

cmFlowSTagVlanPriority 1.3.6.1.4.1.2544.1.12.4.1.4.1.36
This object allows specification of the VLAN Priority to be pushed, based on the value of cmFlowSTagControl. It is applicable for 'push' control type. This object is not applicable for Tranparent Flow; the value should be 0.
Status: current Access: read-create
OBJECT-TYPE    
  VlanPriority  

cmFlowOuterTagPrioEnabled 1.3.6.1.4.1.2544.1.12.4.1.4.1.37
This object is used to specify whether the flow participates in outer-tag priority swap. The Priority Mapping Table cmPrioMapTable allows the A2N outer-tag priority to be specified based on incoming priority at Access Port (based on priority mapping mode - 802.1P, TOS, DSCP). This object is not applicable for Tranparent Flow; the value should be FALSE.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowN2ACOSPriorityTagType 1.3.6.1.4.1.2544.1.12.4.1.4.1.38
This object is used to specify whether the flow uses the inner-tag or the outer-tag in determining the COS (Class of Service) in the N2A direction. This object is applicable in the case of a Multi COS Flow. This object is not supported for Tranparent Flow;
Status: current Access: read-create
OBJECT-TYPE    
  VlanTagType  

cmFlowESFramesLossThreshold 1.3.6.1.4.1.2544.1.12.4.1.4.1.39
This object is used to specify the number of frames lost per flow that starts counting Errored Seconds (ES) on the flow. This functionality is applicable if the flow is monitored using the Y.1731 ESA functionality.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..2147483647  

cmFlowSESFramesLossThresholdRatio 1.3.6.1.4.1.2544.1.12.4.1.4.1.40
This object is used to specify the frame-loss ratio per flow that starts counting Severely Errored Seconds (SES) on the flow. This functionality is applicable if the flow is monitored using the Y.1731 ESA functionality.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..100  

cmFlowPolicingEnabled 1.3.6.1.4.1.2544.1.12.4.1.4.1.41
This object is applicable only when Port is in connection-oriented mode. This object is applicable to both epl and evpl mode flows. This object allows to enable/disable the policing function on the flow.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowPreserveSTagProperties 1.3.6.1.4.1.2544.1.12.4.1.4.1.42
This object is applicable only when Port is in connection-oriented mode. This object is applicable to evpl mode Regular flows, when S-TAG control is specified as SWAPVID. When enabled, this attribute preserves the EtherType (0x88a8) and DEI (Drop Eligibility Indicator) bit in the incoming S-TAG (both from Access and Network Port perspective) into the outgoing S-TAG. When not enabled, the incoming tag is considered as a Q-TAG (0x8100) and both EtherType and CFI (Canonical Form Indicator) bits are over-written by the S-TAG Ethertype (0x88a8) and DEI bit. This object is not applicable for Tranparent Flow; the value should be FALSE.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowInnerTagPrioEnabled 1.3.6.1.4.1.2544.1.12.4.1.4.1.43
This object is used to specify whether the flow participates in inner-tag (second) priority swap. The Priority Mapping Table cmPrioMapTable allows the A2N inner-tag priority to be specified based on incoming priority at Access Port (based on priority mapping mode - 802.1P, TOS, DSCP). This object is not applicable for Tranparent Flow; the value should FALSE.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowN2AOuterTagPrioEnabled 1.3.6.1.4.1.2544.1.12.4.1.4.1.44
This object is used to specify whether the flow participates in outer-tag priority swap in the A2N direction. The Priority Mapping Table cmNetPortPrioMapTable allows the N2A outer-tag priority to be specified based on incoming priority at Network Port (based on priority mapping mode - 802.1P, TOS, DSCP). This object is not applicable for Tranparent Flow; the value should be FALSE.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowA2NShapingType 1.3.6.1.4.1.2544.1.12.4.1.4.1.45
This object is used to specify whether the traffic in A2N direction passing through this flow is shaped by port-level or flow-level Shapers. In case of portbased flows the value of this attribute is flow-based and cannot be changed. In case of regular and default flows Fsp150 products may support both port-based and flow-based shaping.
Status: current Access: read-create
OBJECT-TYPE    
  ShapingType  

cmFlowN2AShapingType 1.3.6.1.4.1.2544.1.12.4.1.4.1.46
This object is used to specify whether the traffic in N2A direction passing through this flow is shaped by port-level or flow-level Shapers. In case of portbased flows the value of this attribute is flow-based and cannot be changed. In case of regular and default flows Fsp150 products may support both port-based and flow-based shaping.
Status: current Access: read-create
OBJECT-TYPE    
  ShapingType  

cmFlowSTagMatchRxPrio 1.3.6.1.4.1.2544.1.12.4.1.4.1.47
This object indicates whether the S-TAG priority is used or ignored for traffic in the N2A direction. This is only applicable if cmFlowSTagControl is 'push'. This object is not applicable for Tranparent Flow; the value should be FALSE.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowAutoBandwidthConfigEnabled 1.3.6.1.4.1.2544.1.12.4.1.4.1.48
This object is applicable for Flows on the PWE3 Ethernet Backplane Port. When set to TRUE bandwidth of this Flow will be automatically adjusted when PWE3 SATOPs are provisioned. The bandwidth will be adjusted based on the TDM entities of associated SATOPs. Flow on ports other than PWE3 Ethernet Backplane Port will always have this value set to FALSE and it is not configurable.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowPort1 1.3.6.1.4.1.2544.1.12.4.1.4.1.49
This object specifies a physical or logical port on the Access side of the Flow. This can be Access Port, Access LAG or Access Split Horizion Group. In case of Tranparent Flow this object specifies port1 of the Flow which is Network-1.
Status: current Access: read-create
OBJECT-TYPE    
  VariablePointer  

cmFlowPort2 1.3.6.1.4.1.2544.1.12.4.1.4.1.50
This object specifies a physical or logical port on the Network side of the Flow. This can be Network Port, Network LAG, Network Split Horizion Group ERP or Protection Group. In case of Tranparent Flow this object specifies port2 of the Flow which is Network-2.
Status: current Access: read-create
OBJECT-TYPE    
  VariablePointer  

cmFlowPolicingControl 1.3.6.1.4.1.2544.1.12.4.1.4.1.51
This object specifies the direction(s) in which Poling is enabled on traffic within this Flow when cmFlowPolicingEnabled is TRUE.
Status: current Access: read-create
OBJECT-TYPE    
  PolicingControl  

cmFlowAutoCIRPercentage 1.3.6.1.4.1.2544.1.12.4.1.4.1.52
This object specifies the percentage of available CIR on the Network ports assigned to this Flow when cmFlowAutoBandwidthConfigEnabled is TRUE. The flow guaranteedBW is set to available BW multiplied by this value. This object is only applicable to Tranparent Flow. The value of this object should be 0 for Access Flow.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..100  

cmFlowLoopAvoidanceObject 1.3.6.1.4.1.2544.1.12.4.1.4.1.53
This object specifies the Loop Avoidance instance to which this Flow belongs. This object is appicable only for Transparent Flow and should point to the ERP instance for which this Flows carries pass-thru traffic. In case of Access Flow the value of this object should be zeroDotZero.
Status: current Access: read-create
OBJECT-TYPE    
  VariablePointer  

cmFlowConfigType 1.3.6.1.4.1.2544.1.12.4.1.4.1.54
This object specifies if this Flow is an Access Flow or Pass-thru Flow.
Status: current Access: read-only
OBJECT-TYPE    
  FlowConfigType  

cmFlowN2NForwardingEnabled 1.3.6.1.4.1.2544.1.12.4.1.4.1.55
This object is used to specify whether n2n forwarding is enabled on particular Flow.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowA2NMulticastRateLimitControl 1.3.6.1.4.1.2544.1.12.4.1.4.1.56
Whether multicast frames are limited per Flow.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmFlowA2NMulticastRateLimitLo 1.3.6.1.4.1.2544.1.12.4.1.4.1.57
The rate limit for multicast packets per Flow. When cmFlowA2NMulticastRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the low-order 32-bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowA2NMulticastRateLimitHi 1.3.6.1.4.1.2544.1.12.4.1.4.1.58
The rate limit for multicast packets per Flow. When cmFlowA2NMulticastRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the high-order 32-bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowA2NBroadcastRateLimitControl 1.3.6.1.4.1.2544.1.12.4.1.4.1.59
Whether broadcast frames are limited per Flow.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmFlowA2NBroadcastRateLimitLo 1.3.6.1.4.1.2544.1.12.4.1.4.1.60
The rate limit for multicast packets per Flow. When cmFlowA2NBroadcastRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the low-order 32-bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowA2NBroadcastRateLimitHi 1.3.6.1.4.1.2544.1.12.4.1.4.1.61
The rate limit for multicast packets per Flow. When cmFlowA2NBroadcastRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the high-order 32-bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowA2NCombinedRateLimitControl 1.3.6.1.4.1.2544.1.12.4.1.4.1.62
Whether both multicast and broadcast frames are limited per Flow.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmFlowA2NCombinedRateLimitLo 1.3.6.1.4.1.2544.1.12.4.1.4.1.63
The rate limit for multicast packets per Flow. When cmFlowA2NCombinedRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the low-order 32-bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowA2NCombinedRateLimitHi 1.3.6.1.4.1.2544.1.12.4.1.4.1.64
The rate limit for multicast packets per Flow. When cmFlowA2NCombinedRateLimiteControl is set and value is 0, then all multicast frames are dropped. This object represents the high-order 32-bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowRefPrioMapProfile 1.3.6.1.4.1.2544.1.12.4.1.4.1.65
This object used to specify the flow's profile.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmFlowRefEoMplsPwObject 1.3.6.1.4.1.2544.1.12.4.1.4.1.66
This object specifies EoMpls Pw object OID.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmFlowRefN2APrioMapProfile 1.3.6.1.4.1.2544.1.12.4.1.4.1.67
This object used to specify the flow's N2A direction profile.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmFlowSecureBlockingEnabled 1.3.6.1.4.1.2544.1.12.4.1.4.1.68
This object can be used to enable/disable secure block.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmFlowRefConnectGuardFlowList 1.3.6.1.4.1.2544.1.12.4.1.4.1.69
This object specifies the secure flow list, it should be f3ConnectGuardFlowIndex value list split with comma.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cmFlowSecureStateList 1.3.6.1.4.1.2544.1.12.4.1.4.1.70
This object specifies the secure state list, it should be secure state value list and split with comma.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

cmFlowCpdTable 1.3.6.1.4.1.2544.1.12.4.1.5
A list of entries corresponding to Flow Control Protocol Disposition. This table is only applicable for FSP150CM Hub Shelf Release 3.x.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmFlowCpdEntry

cmFlowCpdEntry 1.3.6.1.4.1.2544.1.12.4.1.5.1
A conceptual row in the cmFlowCpdTable. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Network Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmFlowCpdEntry  

cmFlowCpdIndex 1.3.6.1.4.1.2544.1.12.4.1.5.1.1
An arbitrary integer index value used to uniquely identify this CPD Service Entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

cmFlowCpdFilterType 1.3.6.1.4.1.2544.1.12.4.1.5.1.2
This enables specification of type of CPD Filter.
Status: current Access: read-only
OBJECT-TYPE    
  CmControlProtocolFilterType  

cmFlowCpdFilterDescr 1.3.6.1.4.1.2544.1.12.4.1.5.1.3
This provides description of CPD Filter.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

cmFlowCpdDispType 1.3.6.1.4.1.2544.1.12.4.1.5.1.4
This enables specification of disposion type of CPD Filter.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdMacAddressMatch 1.3.6.1.4.1.2544.1.12.4.1.5.1.5
This enables provides the Filter MAC Address to match.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmFlowCpdMacAddressMask 1.3.6.1.4.1.2544.1.12.4.1.5.1.6
This enables provides the Filter MAC Address Mask to match.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmFlowCpdEthertype 1.3.6.1.4.1.2544.1.12.4.1.5.1.7
This enables provides the Filter Ethertype to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cmFlowCpdEthertypeMask 1.3.6.1.4.1.2544.1.12.4.1.5.1.8
This enables provides the Filter Ethertype Mask to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmFlowCpdSubtype 1.3.6.1.4.1.2544.1.12.4.1.5.1.9
This enables provides the Filter Subtype to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmFlowCpdSubtypeMask 1.3.6.1.4.1.2544.1.12.4.1.5.1.10
This enables provides the Filter Subtype Mask to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmQosShaperTable 1.3.6.1.4.1.2544.1.12.4.1.6
A list of entries corresponding to Ethernet Quality of Service Shaper for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmQosShaperEntry

cmQosShaperEntry 1.3.6.1.4.1.2544.1.12.4.1.6.1
A conceptual row in the cmQosShaperTable. These entries represent a Quality of Service Shaper.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmQosShaperEntry  

cmQosShaperTypeIndex 1.3.6.1.4.1.2544.1.12.4.1.6.1.1
The unique index value corresponding to a Quality of Service Shaper's direction. Values 1 and 2 are applicable to the Access Flow Shaper: - value of 1 stands for A2N direction, - value of 2 stands for N2A direction. Values 3 and 4 are applicable to Pass-thru Flow Shaper (new in 5.6CC release): - value of 3 stands for N1toN2 direction - value of 4 stands for N2toN1 direction
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..4  

cmQosShaperIndex 1.3.6.1.4.1.2544.1.12.4.1.6.1.2
The unique integer index value corresponding to a Quality of Service Shaper. In release 5.6CC the range is extended to 1..16 to support duplicate A2N shapers on a Flow. The duplicate shapers are created under a Flow if network interface of the Flow is ERP Group or Split Horizon Group. In case of multi-cos Flow indices 1..8 represent shapers of COS 0..7 going to Network 1 port; indices 9..16 represent shapers for COS 0..7 going to Network 2 port. In case of single-cos Flow index 1 represents shaper going to Network 1 port; index 9 represents shaper going to Network 2 port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..16  

cmQosShaperDirection 1.3.6.1.4.1.2544.1.12.4.1.6.1.3
The direction of the Quality of Service Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  TrafficDirection  

cmQosShaperAdminState 1.3.6.1.4.1.2544.1.12.4.1.6.1.4
This object represents the Administrative State of the QOS Shaper.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmQosShaperOperationalState 1.3.6.1.4.1.2544.1.12.4.1.6.1.5
This object represents the Operational State of the QOS Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmQosShaperSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.6.1.6
This object represents the Secondary State of the QOS Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmQosShaperCIR 1.3.6.1.4.1.2544.1.12.4.1.6.1.7
This object represents the Commited Information Rate(CIR) (Lower 32 bits)of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperCBS 1.3.6.1.4.1.2544.1.12.4.1.6.1.8
This object represents the Commited Burst Size (CBS) of the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperEIR 1.3.6.1.4.1.2544.1.12.4.1.6.1.9
This object represents the Excess Information Rate(EIR) (Lower 32 bits) of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperEBS 1.3.6.1.4.1.2544.1.12.4.1.6.1.10
This object represents the Excess Burst Size (EBS) of the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperBufferSize 1.3.6.1.4.1.2544.1.12.4.1.6.1.11
This object represents the Buffer Size of the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperStorageType 1.3.6.1.4.1.2544.1.12.4.1.6.1.12
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmQosShaperRowStatus 1.3.6.1.4.1.2544.1.12.4.1.6.1.13
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmQosShaperRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmQosShaperRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmQosShaperRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmQosShaperCOS 1.3.6.1.4.1.2544.1.12.4.1.6.1.14
This object provides the COS (Class of Service) value for the QOS Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

cmQosShaperCIRHi 1.3.6.1.4.1.2544.1.12.4.1.6.1.15
This object represents the Commited Information Rate(CIR) (Higher 32 bits) of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperEIRHi 1.3.6.1.4.1.2544.1.12.4.1.6.1.16
This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperSoamCIRLo 1.3.6.1.4.1.2544.1.12.4.1.6.1.17
This object represents the Soam Commited Information Rate(SOAM-CIR) (Lower 32 bits) of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperSoamCIRHi 1.3.6.1.4.1.2544.1.12.4.1.6.1.18
This object represents the Soam Commited Information Rate(SOAM-CIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperSoamEIRLo 1.3.6.1.4.1.2544.1.12.4.1.6.1.19
This object represents the Soam Excess Information Rate(SOAM-EIR) (Lower 32 bits) of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperSoamEIRHi 1.3.6.1.4.1.2544.1.12.4.1.6.1.20
This object represents the Soam Excess Information Rate(SOAM-EIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperWredGreenMinQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.6.1.21
This object represents the Wred green packet min queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperWredGreenMaxQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.6.1.22
This object represents the Wred green packet max queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperWredGreenDropProbability 1.3.6.1.4.1.2544.1.12.4.1.6.1.23
This object represents the Wred green packet drop probability.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperWredYellowMinQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.6.1.24
This object represents the Wred yellow packet min queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperWredYellowMaxQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.6.1.25
This object represents the Wred yellow packet max queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosShaperWredYellowDropProbability 1.3.6.1.4.1.2544.1.12.4.1.6.1.26
This object represents the Wred yellow packet drop probability.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmEthernetNetPortTable 1.3.6.1.4.1.2544.1.12.4.1.7
A list of entries corresponding to Ethernet Network Port Facilities for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetNetPortEntry

cmEthernetNetPortEntry 1.3.6.1.4.1.2544.1.12.4.1.7.1
A conceptual row in the cmEthernetNetPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetNetPortEntry  

cmEthernetNetPortIndex 1.3.6.1.4.1.2544.1.12.4.1.7.1.1
An integer index value used to uniquely identify this Ethernet Network Port within a card. Note that each Ethernet Network Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, cmEthernetNetPortIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

cmEthernetNetPortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.7.1.2
This object has the same value as ifIndex for Ethernet Network Port. An integer index value used to uniquely identify this Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

cmEthernetNetPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.7.1.3
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

cmEthernetNetPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.7.1.4
This object represents the Administrative State of the Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmEthernetNetPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.7.1.5
This object represents the Operational State of the Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmEthernetNetPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.7.1.6
This object represents the Secondary State of the Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmEthernetNetPortMTU 1.3.6.1.4.1.2544.1.12.4.1.7.1.7
This object provides the MTU on the Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortMediaType 1.3.6.1.4.1.2544.1.12.4.1.7.1.8
This object represents the type of Ethernet Media on the Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetMediaType  

cmEthernetNetPortConfigSpeed 1.3.6.1.4.1.2544.1.12.4.1.7.1.9
This object allows to configure the speed of the Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetPortSpeed  

cmEthernetNetPortNegotiatedSpeed 1.3.6.1.4.1.2544.1.12.4.1.7.1.10
This object provides the negotiated speed of the Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  EthernetPortSpeed  

cmEthernetNetPortMDIXType 1.3.6.1.4.1.2544.1.12.4.1.7.1.11
This object allows management of MDIX property on Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetMDIXType  

cmEthernetNetPortJumboFramesEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.12
This object allows enabling/disabling jumbo frames support on the Ethernet Network Port. This object is only applicable for Ethernet Network Port on R3.1CM NTU Card.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortSfpVendorName 1.3.6.1.4.1.2544.1.12.4.1.7.1.13
This object provides the vendor name of the SFP. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

cmEthernetNetPortSfpPartNumber 1.3.6.1.4.1.2544.1.12.4.1.7.1.14
This object provides the part number of the SFP. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

cmEthernetNetPortSfpSerialNumber 1.3.6.1.4.1.2544.1.12.4.1.7.1.15
This object provides the serial number of the SFP. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

cmEthernetNetPortSfpDateOfManufacture 1.3.6.1.4.1.2544.1.12.4.1.7.1.16
This object provides the date of manufacture of the SFP. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

cmEthernetNetPortSfpConnectorValue 1.3.6.1.4.1.2544.1.12.4.1.7.1.17
This object provides the SFP connector value. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  SfpConnectorValue  

cmEthernetNetPortInitiateDiag 1.3.6.1.4.1.2544.1.12.4.1.7.1.18
This object allows to initiate Etherjack diagnosis on the Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetDiagAction  

cmEthernetNetPortDiagnosePair1Cond 1.3.6.1.4.1.2544.1.12.4.1.7.1.19
This object provides diagnosis results for the cable Pair 1 on Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetNetPortDiagnosePair2Cond 1.3.6.1.4.1.2544.1.12.4.1.7.1.20
This object provides diagnosis results for the cable Pair 2 on Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetNetPortDiagnosePair3Cond 1.3.6.1.4.1.2544.1.12.4.1.7.1.21
This object provides diagnosis results for the cable Pair 3 on Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetNetPortDiagnosePair4Cond 1.3.6.1.4.1.2544.1.12.4.1.7.1.22
This object provides diagnosis results for the cable Pair 4 on Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetNetPortDiagnoseAutoNegCond 1.3.6.1.4.1.2544.1.12.4.1.7.1.23
This object provides auto negotiation results of the diagnosis test on Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagAutoNegCondType  

cmEthernetNetPortDiagnoseLpbkCond 1.3.6.1.4.1.2544.1.12.4.1.7.1.24
This object provides port loopback results of the diagnosis test on Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagLpbkCondType  

cmEthernetNetPortDiagnoseEfmLpbkCond 1.3.6.1.4.1.2544.1.12.4.1.7.1.25
This object provides remote EFM loopback results of the diagnosis test on Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagEfmOamLpbkCondType  

cmEthernetNetPortDiagnoseResult 1.3.6.1.4.1.2544.1.12.4.1.7.1.26
This object provides results of the diagnosis test in string form on Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

cmEthernetNetPortDiagnoseTestStatus 1.3.6.1.4.1.2544.1.12.4.1.7.1.27
This object provides the current status of the diagnosis test on Ethernet Access Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagTestStatus  

cmEthernetNetPortDiagnoseTestTime 1.3.6.1.4.1.2544.1.12.4.1.7.1.28
This object provides the time when diagnosis test was last executed.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

cmEthernetNetPortLoopbackConfig 1.3.6.1.4.1.2544.1.12.4.1.7.1.29
This object allows to initiate loopbacks on on the Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmLoopbackType  

cmEthernetNetPortLoopbackStatus 1.3.6.1.4.1.2544.1.12.4.1.7.1.30
This object provides status of the current loopback on the Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmLoopbackType  

cmEthernetNetPortLoopbackTime 1.3.6.1.4.1.2544.1.12.4.1.7.1.31
This object allows to specify time for timed-loopbacks on on the Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..300  

cmEthernetNetPortLoopbackSwapSADA 1.3.6.1.4.1.2544.1.12.4.1.7.1.32
This object allows to specify whether or not the loopbacked frame will have the Source Address and Destination Address swapped.
Status: current Access: read-write
OBJECT-TYPE    
  CmSwapSADAType  

cmEthernetNetPortOuterVlanLoopbackMask 1.3.6.1.4.1.2544.1.12.4.1.7.1.33
This object allows specification of the outer VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Outer VLAN 1 Loopback Enabled 2 Outer VLAN 2 Loopback Enabled 4 Outer VLAN 3 Loopback Enabled Value of 0 means that no VLANs are enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

cmEthernetNetPortOuterVlanLoopback1 1.3.6.1.4.1.2544.1.12.4.1.7.1.34
This object allows specification of the outer VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetNetPortOuterVlanLoopback2 1.3.6.1.4.1.2544.1.12.4.1.7.1.35
This object allows specification of the outer VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetNetPortOuterVlanLoopback3 1.3.6.1.4.1.2544.1.12.4.1.7.1.36
This object allows specification of the outer VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetNetPortInnerVlanLoopbackMask 1.3.6.1.4.1.2544.1.12.4.1.7.1.37
This object allows specification of the inner VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Inner VLAN 1 Loopback Enabled 2 Inner VLAN 2 Loopback Enabled 4 Inner VLAN 3 Loopback Enabled Value of 0 means that no VLANs are enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

cmEthernetNetPortInnerVlanLoopback1 1.3.6.1.4.1.2544.1.12.4.1.7.1.38
This object allows specification of the inner VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetNetPortInnerVlanLoopback2 1.3.6.1.4.1.2544.1.12.4.1.7.1.39
This object allows specification of the inner VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetNetPortInnerVlanLoopback3 1.3.6.1.4.1.2544.1.12.4.1.7.1.40
This object allows specification of the inner VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetNetPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetNetPortLinkLossFwdEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.41
This object allows enabling/disabling link loss forwarding on the Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortLinkLossFwdSignalType 1.3.6.1.4.1.2544.1.12.4.1.7.1.42
This object allows definition of the link loss forwarding signalling type. This is applicable only if cmEthernetNetPortLinkLossFwdEnabled is enabled. This object is only valid for FSP150CM Release 3.1. This object is deprecated henceforth. Link Loss signalling will be supported using the object cmEthernetAccPortLinkLossFwdTxActionType.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmLinkLossFwdSignalType  

cmEthernetNetPortLinkLossFwdTriggerTypes 1.3.6.1.4.1.2544.1.12.4.1.7.1.43
This object allows definition of the link loss forwarding trigger types. This is applicable only if cmEthernetAccPortLinkLossFwdEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  CmLinkLossFwdTriggerTypes  

cmEthernetNetPortLinkLossFwdDelay 1.3.6.1.4.1.2544.1.12.4.1.7.1.44
This object allows specification of the delay between detection of link loss and signalling of link loss forwarding. Time specified is in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortLinkLossFwdActive 1.3.6.1.4.1.2544.1.12.4.1.7.1.45
This object provides the link loss forwarding status indicating if link loss forwarding is currently being signaled via the port.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortLinkLossFwdPartnerEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.46
This object provides the indication of a link partners ability to support link loss forwarding via EFM, i.e. from received organization specific OAMPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortLinkLossFwdLocalLinkId 1.3.6.1.4.1.2544.1.12.4.1.7.1.47
This object allows configuration of the Local Link Id on Ethernet Network port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortLinkLossFwdRemoteLinkIds 1.3.6.1.4.1.2544.1.12.4.1.7.1.48
This object allows enabling/disabling Remote Link Ids on Ethernet Network port. By setting the appropriate bit positions, the Ethernet Network port is able to distinguish the remote side client ports from the Remote Link Down PDUs coming from remote end.
Status: current Access: read-write
OBJECT-TYPE    
  CmRemoteLinkIds  

cmEthernetNetPortOamId 1.3.6.1.4.1.2544.1.12.4.1.7.1.49
OAM Id. This is unique EFM OAM sublayer port id.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortOamAdminDisposition 1.3.6.1.4.1.2544.1.12.4.1.7.1.50
Ethernet Network Port's EFM OAM Administrative Disposition. This object is applicable only for FSP150CM Release 3.1. This object is deprecated henceforth. With FSP150CC Release 4.1, this property is managed using the Control Protocol Disposition tables.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortOamDiscoveryState 1.3.6.1.4.1.2544.1.12.4.1.7.1.51
Ethernet Network Port's OAM discovery state.
Status: current Access: read-only
OBJECT-TYPE    
  CmOamDiscoveryState  

cmEthernetNetPortOamLocalVarRtrvsEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.52
This object allows specification of whether the Ethernet Network Port supports sending variable response OAMPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortOamLocalLinkEventsEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.53
This object allows specification of whether the Ethernet Network Port supports interpreting Link Events.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortOamLocalOamLoopbacksSupported 1.3.6.1.4.1.2544.1.12.4.1.7.1.54
This object allows specification of whether the Ethernet Network Port is capable of OAM remote loopback mode.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortOamLocalUnidirSupportEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.55
This object allows specification of whether the Ethernet Network Port is capable of sending OAMPDUs when the receive path is non-operational.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortOamLocalMaxPDUSize 1.3.6.1.4.1.2544.1.12.4.1.7.1.56
This object represents the largest OAMPDU, in octets, supported by the Ethernet Network Port. This value is compared to the remote Maximum PDU Size and the smaller of the two is used.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortOamLocalMode 1.3.6.1.4.1.2544.1.12.4.1.7.1.57
This object allows to configure the OAM sublayer entity in either Active or Passive mode.
Status: current Access: read-write
OBJECT-TYPE    
  CmOamMode  

cmEthernetNetPortOamRemoteMacAddress 1.3.6.1.4.1.2544.1.12.4.1.7.1.58
This object allows retrieval of the Remote Mac Address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cmEthernetNetPortOamRemoteVarRtrvsEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.59
This object allows retrieval of whether the remote OAM entity supports sending variable response OAMPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortOamRemoteLinkEventsEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.60
This object allows retrieval of whether the remote OAM entity supports interpreting Link Events.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortOamRemoteOamLoopbacksSupported 1.3.6.1.4.1.2544.1.12.4.1.7.1.61
This object allows retrieval of whether the remote OAM entity supports OAM remote loopback mode.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortOamRemoteUnidirSupportEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.62
This object allows retrieval of whether the remote OAM entity is capable of sending OAMPDUs when the receive path is non-operational.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortOamRemoteMaxPDUSize 1.3.6.1.4.1.2544.1.12.4.1.7.1.63
This object allows retrieval of the remote OAM entity maximum OAMPDU size.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortOamRemoteMode 1.3.6.1.4.1.2544.1.12.4.1.7.1.64
This object allows to retrieve whether the remote OAM sublayer entity is either in Active or Passive mode.
Status: current Access: read-only
OBJECT-TYPE    
  CmOamMode  

cmEthernetNetPortRxPauseDisposition 1.3.6.1.4.1.2544.1.12.4.1.7.1.65
This object allows enabling/disabling receive pause frames on Ethernet Network port. This object is not applicable for FSP150CC Release 4.1 products.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortTxPauseEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.66
This object allows enabling/disabling transmit pause frames on Ethernet Network port. This object is not applicable for FSP150CC Release 4.1 products.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortAfpType 1.3.6.1.4.1.2544.1.12.4.1.7.1.67
This object allows specification of the Acceptable Frame Policy on Ethernet Network port. Users can specify whether the port supports only tagged frames, only untagged frames or both tagged and untagged frames. This object is not applicable for FSP150CC Release 4.1 products.
Status: current Access: read-write
OBJECT-TYPE    
  CmAfpType  

cmEthernetNetPortMDIXStatus 1.3.6.1.4.1.2544.1.12.4.1.7.1.68
This object provides the current MDIX status of the Ethernet Network port.
Status: current Access: read-only
OBJECT-TYPE    
  CmEthernetMDIXType  

cmEthernetNetPortSfpReach 1.3.6.1.4.1.2544.1.12.4.1.7.1.69
This object provides the SFP Reach in meters. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortSfpLaserWaveLength 1.3.6.1.4.1.2544.1.12.4.1.7.1.70
This object provides the SFP Laser Wave Length in nano meters. This is applicable only when cmEthernetNetPortMediaType is fiber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortSfpMediaType 1.3.6.1.4.1.2544.1.12.4.1.7.1.71
This object provides the SFP Media Type. This is applicable when cmEthernetNetPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  SfpMediaType  

cmEthernetNetPortOamEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.72
This object allows to manage the EFM OAM on Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortOamAdminState 1.3.6.1.4.1.2544.1.12.4.1.7.1.73
This object provides the EFM OAM Admin State.
Status: current Access: read-only
OBJECT-TYPE    
  CmOamAdminState  

cmEthernetNetPortShapingEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.74
This object allows to manage the Network Port Shaping. When enabled, values in cmEthernetNetPortShapedSpeedLo and cmEthernetNetPortShapedSpeedHi are applicable.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortShapedSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.7.1.75
This object allows to specify the lower 32 bits of the Network Port Shaped speed. This value is applicable when cmEthernetNetPortShapingEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmEthernetNetPortShapedSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.7.1.76
This object allows to specify the higher 32 bits of the Network Port Shaped speed. This value is applicable when cmEthernetNetPortShapingEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmEthernetNetPortQinQEtherType 1.3.6.1.4.1.2544.1.12.4.1.7.1.77
This object allows to specify the Q-in-Q Ether Type on the Network Port. Setting this value to 0 will disable the Q-in-Q override on the Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmEthernetNetPortLinkLossFwdTxActionType 1.3.6.1.4.1.2544.1.12.4.1.7.1.78
This object allows to specify the Network Port's behavior when link loss forwarding trigger events occur on the Access Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmLinkLossFwdTxActionType  

cmEthernetNetPortLinkLossFwdRxRLDLinkIds 1.3.6.1.4.1.2544.1.12.4.1.7.1.79
This object provides the received Remote Link IDs in EFM RLD messages on the Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmRemoteLinkIds  

cmEthernetNetPortAutoDiagEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.80
This object allows to enable or disable the automatic Cable Diagnostic tests when the cable is removed from the port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortSyncEEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.81
This object allows to specify whether the Ethernet Network Port can be enabled/disabled for Synchronous Ethernet. This object is only applicable for Synchronous Ethernet capable ports. When enabled, on receive side -port can extract the frequency of its input signal and pass the recovered clock to the system clock -port processes the ESMC(Ethernet Synchronization Messaging Channel) and extracts the QL (when also QL enabled) -port is eligible to be selected as a system clock reference When enabled, on transmit side -port's transmit clock is locked to the system clock -port generates an ESMC to generate a QL (when also QL enabled) When disabled, on receive side, -port does not pass the recovered clock to the system clock -port does not process the ESMC (if present) -port is not eligible to be selected as a system clock reference When disabled, on transmit side -port's output frequency may be synchronized to the system clock -port does not generate an ESMC.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortQLModeEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.82
This object allows to specify whether the Ethernet Network Port can be enabled/disabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetNetPortQLModeEnabled is set to true. When enabled, on receive side -port shall PEER the SSM (Sync Status Messages) slow protocol PDUs and take appropriate action When enabled, on transmit side -port shall periodically (once a second) transmit QL TLV information PDUs When disabled, on receive side, -port shall terminate and discard any SSM slow protocol PDUs When disabled, on transmit side -port shall not transmit any SSM slow protocol PDUs.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortExpectedQL 1.3.6.1.4.1.2544.1.12.4.1.7.1.83
This object allows to specify the expected QL when the Ethernet Network Port is enabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetNetPortQLModeEnabled is set to true. This object allows the user to set a minimum expected received Quality Level on the port. The valid values depend upon the SYNC entity's Network Clock Type. A value of None represents that a minimum Quality Level is not expected. The default value shall be None.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetNetPortAssumedQL 1.3.6.1.4.1.2544.1.12.4.1.7.1.84
This object allows to specify the assumed QL on the Ethernet Network Port. This object is only applicable for Synchronous Ethernet capable ports. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port's QL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetNetPortReceivedQL 1.3.6.1.4.1.2544.1.12.4.1.7.1.85
This object provides the Received QL value for the Ethernet port. If the Ethernet port's QL Mode is disabled, then the received QL value is not applicable.This object is only applicable for Synchronous Ethernet capable ports.
Status: current Access: read-only
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetNetPortTransmitQL 1.3.6.1.4.1.2544.1.12.4.1.7.1.86
This object provides the Transmitted QL value for the Ethernet port. If the Ethernet port's QL Mode is disabled, then the received QL value is not applicable. This object is only applicable for Synchronous Ethernet capable ports.
Status: current Access: read-only
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetNetPortPrioMapMode 1.3.6.1.4.1.2544.1.12.4.1.7.1.87
This object provides the Priority Mapping Mode used for classification of frames.
Status: current Access: read-only
OBJECT-TYPE    
  PriorityMapMode  

cmEthernetNetPortDeiEnable 1.3.6.1.4.1.2544.1.12.4.1.7.1.88
This is a port level control to reset the DEI (Drop Eligibility Indicator) bit in the S-Tag, if the downstream equipment supports S-Tag TPID (EtherType) but cannot handle DEI bit set. In the receive direction, it uses the S-TAG DEI when enabled, else ignores it. The following comment is NOT relevant to OSA8.1.1, since this object is still supported by OSA8.1.1. The object has been deprecated. The respective configuration should be managed by following objects: cmEthernetNetPortRxDeiAction, cmEthernetNetPortTxDeiAction, cmEthernetNetPortRxDeiOuterTagType, cmEthernetNetPortTxDeiOuterTagType.
Status: deprecated Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortPcpDEEncType 1.3.6.1.4.1.2544.1.12.4.1.7.1.89
This is a port level control that specifies the mode of drop eligibility encoding in PCP bits of the VLAN tag.
Status: current Access: read-write
OBJECT-TYPE    
  PcpDEEncType  

cmEthernetNetPortPcpDEPairsAction 1.3.6.1.4.1.2544.1.12.4.1.7.1.90
This object allows the SNMP user to manage the Priority Code Point (PCP) Drop Eligibility Pairs. When the cmEthernetNetPortPcpDEEncType is of type 7p1d, 6p2d, 5p3d, the cmNetPortPcpDEPairTable can be used to specify alternate pairs of priorities to specify drop eligibility/ ineligibility.
Status: current Access: read-write
OBJECT-TYPE    
  PcpDEPairsAction  

cmEthernetNetPortSSMRemoteMacAddress 1.3.6.1.4.1.2544.1.12.4.1.7.1.91
This object allows retrieval of the Remote Mac Address, when the port is peering using SSM.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cmEthernetNetPortXgePhyType 1.3.6.1.4.1.2544.1.12.4.1.7.1.92
This object allows to specify the PHY type of 10G Ethernet Port. 10G ports can operate in LAN-PHY or WAN-PHY mode. The default mode is LAN-PHY and port rate in this mode is 10Gbps. In WAN-PHY mode the port rate is 9.29Gbps. This attribute is only applicable for ports configured to work at speed-10G-full. For other speeds the value of this object must be 'not-applicable' and cannot be changed.
Status: current Access: read-write
OBJECT-TYPE    
  XgePhyType  

cmEthernetNetPortLoopbackSourceMacControlEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.93
This object allows to Enable/Disable the Net Port Source MAC Address frame matching criteria for all streams. Not applicable for: efm-oam-remote, efm-oam-remote-timed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortLoopbackDestMacControlEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.94
This object allows to Enable/Disable the Net Port Destination MAC Address frame matching criteria for all streams. Not applicable for: efm-oam-remote, efm-oam-remote-timed.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortLoopbackSourceMacAddress 1.3.6.1.4.1.2544.1.12.4.1.7.1.95
This object allows to set Net Port Source MAC Address for frame matching when Net Port Source MAC Control is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmEthernetNetPortLoopbackDestMacAddress 1.3.6.1.4.1.2544.1.12.4.1.7.1.96
This object allows to set Net Port Destination MAC Address for frame matching when Net Port Destination MAC Control is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmEthernetNetPortLoopbackBlockingEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.97
This object allows frame blocking when loopback is active. - True: Blocks frames in the non-loopback direction that match the PORT or VLAN received in the non-loopback direction. Discards frames in the loopback direction that match the PORT or VLAN, but do not match the MAC address criteria, - False: No blocking of frames.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortRxDeiAction 1.3.6.1.4.1.2544.1.12.4.1.7.1.98
This object allows to specify the Receive DEI Action.
Status: current Access: read-write
OBJECT-TYPE    
  RxDeiAction  

cmEthernetNetPortTxDeiAction 1.3.6.1.4.1.2544.1.12.4.1.7.1.99
This object allows to specify the Transmit DEI Action.
Status: current Access: read-write
OBJECT-TYPE    
  TxDeiAction  

cmEthernetNetPortRxDeiOuterTagType 1.3.6.1.4.1.2544.1.12.4.1.7.1.100
This object allows to specify the Receive DEI Outer Tag Type.
Status: current Access: read-write
OBJECT-TYPE    
  DeiOuterTagType  

cmEthernetNetPortTxDeiOuterTagType 1.3.6.1.4.1.2544.1.12.4.1.7.1.101
This object allows to specify the Transmit DEI Outer Tag Type.
Status: current Access: read-write
OBJECT-TYPE    
  DeiOuterTagType  

cmEthernetNetPortLaserWDMChannel 1.3.6.1.4.1.2544.1.12.4.1.7.1.102
Channel number of WDM tunable XFP setting.
Status: current Access: read-write
OBJECT-TYPE    
  SfpChannelIdentifier  

cmEthernetNetPortLaserIsTunable 1.3.6.1.4.1.2544.1.12.4.1.7.1.103
Channel number of WDM tunable XFP setting.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortLaserFrequency 1.3.6.1.4.1.2544.1.12.4.1.7.1.104
Channel number of WDM tunable XFP setting.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cmEthernetNetPortMediaTypeAutoSelected 1.3.6.1.4.1.2544.1.12.4.1.7.1.105
This object provides the auto selected Ethernet Media of the Ethernet Network Port.
Status: current Access: read-only
OBJECT-TYPE    
  EthernetMediaType  

cmEthernetNetPortLowLatencyQueuingEnabled 1.3.6.1.4.1.2544.1.12.4.1.7.1.106
This object allows to Enable/Disable the Low Latency Queuing on the Ethernet Network Port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortDiagnosticMacAddress 1.3.6.1.4.1.2544.1.12.4.1.7.1.107
This object describes the diagnose mac address for SAT, ECPA, JDSU, Loopback with Override SA etc.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cmEthernetNetPortIngressCOSPriority 1.3.6.1.4.1.2544.1.12.4.1.7.1.108
Indicates the VLAN tag to use for PCP Priority to COS mapping when the port Priority Map Mode is 802.1p. Supported values are inner-vlantag and outer-vlantag. This attribute is only applicable on products when Flowpoint Model is supported. inner-vlantag: The inner VLAN tag PCP Priority of a frame is used for ingress COS mapping. A frame with no inner VLAN tag (untagged or single-tagged) will have a COS equal to the default COS of the port. outer-vlantag: The outer VLAN tag PCP Priority of a frame is used for ingress COS mapping. A frame with no outer VLAN tag (untagged) will have a COS equal to the default COS of the port. This attribute has been deprecated and is not supported. Now, the Priority Map Mode indicates whether it is inner or outer. Use priomap-8021p(4) for outer and priomap-8021p-inner(5) for inner.
Status: deprecated Access: read-write
OBJECT-TYPE    
  VlanTagType  

cmEthernetNetPortDefaultCOS 1.3.6.1.4.1.2544.1.12.4.1.7.1.109
The COS assigned to a frame that does not have a valid COS identifier for the Priority Map Mode of the port. This attribute is only applicable on products when Flowpoint Model is supported. This value is assigned to a frame received on a port when: - the cmEthernetNetPortPrioMapMode=priomap-8021p, ingressCOSPriority=inner-vlantag; and the frame is untagged - the cmEthernetNetPortPrioMapMode=priomap-8021p, ingressCOSPriority=inner-vlantag; and the frame has a single VLAN tag - the cmEthernetNetPortPrioMapMode=priomap-8021p, ingressCOSPriority=outer-vlantag; and the frame is untagged - the cmEthernetNetPortPrioMapMode=priomap-dscp; and the frame does not have an IP ethertype - the cmEthernetNetPortPrioMapMode=priomap-tos; and the frame does not have an IP ethertype. This attribute has been deprecated and is not supported. The Default COS is determined from the flowpoint's associated Priority Mapping Profle.
Status: deprecated Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmEthernetNetPortTrafficModel 1.3.6.1.4.1.2544.1.12.4.1.7.1.110
The Traffic Management connection model available for the port. - accessFlow: NID Traffic Connection model. - flowpoint: Multipoint and Aggregation Traffic Connection model.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetPortTrafficModel  

cmEthernetNetPortCpdTable 1.3.6.1.4.1.2544.1.12.4.1.8
A list of entries corresponding to Ethernet Network Port Control Protocol Disposition. This table is only applicable for FSP150CM Hub Shelf Release 3.x.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetNetPortCpdEntry

cmEthernetNetPortCpdEntry 1.3.6.1.4.1.2544.1.12.4.1.8.1
A conceptual row in the cmEthernetNetPortCpdTable. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Network Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetNetPortCpdEntry  

cmEthernetNetPortCpdIndex 1.3.6.1.4.1.2544.1.12.4.1.8.1.1
An arbitrary integer index value used to uniquely identify this CPD Service Entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

cmEthernetNetPortCpdFilterType 1.3.6.1.4.1.2544.1.12.4.1.8.1.2
This enables specification of type of CPD Filter.
Status: current Access: read-only
OBJECT-TYPE    
  CmControlProtocolFilterType  

cmEthernetNetPortCpdFilterDescr 1.3.6.1.4.1.2544.1.12.4.1.8.1.3
This provides description of CPD Filter.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

cmEthernetNetPortCpdDispType 1.3.6.1.4.1.2544.1.12.4.1.8.1.4
This enables specification of disposion type of CPD Filter.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdMacAddressMatch 1.3.6.1.4.1.2544.1.12.4.1.8.1.5
This enables provides the Filter MAC Address to match.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmEthernetNetPortCpdMacAddressMask 1.3.6.1.4.1.2544.1.12.4.1.8.1.6
This enables provides the Filter MAC Address Mask to match.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmEthernetNetPortCpdEthertype 1.3.6.1.4.1.2544.1.12.4.1.8.1.7
This enables provides the Filter Ethertype to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cmEthernetNetPortCpdEthertypeMask 1.3.6.1.4.1.2544.1.12.4.1.8.1.8
This enables provides the Filter Ethertype Mask to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortCpdSubtype 1.3.6.1.4.1.2544.1.12.4.1.8.1.9
This enables provides the Filter Subtype to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortCpdSubtypeMask 1.3.6.1.4.1.2544.1.12.4.1.8.1.10
This enables provides the Filter Subtype Mask to match.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetMgmtPortTable 1.3.6.1.4.1.2544.1.12.4.1.9
A list of entries corresponding to Ethernet Management Port Facilities for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetMgmtPortEntry

cmEthernetMgmtPortEntry 1.3.6.1.4.1.2544.1.12.4.1.9.1
A conceptual row in the cmEthernetMgmtPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetMgmtPortEntry  

cmEthernetMgmtPortIndex 1.3.6.1.4.1.2544.1.12.4.1.9.1.1
An integer index value used to uniquely identify this Ethernet Management Port within a card. Note that each Ethernet Management Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, cmEthernetMgmtPortIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

cmEthernetMgmtPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.9.1.2
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

cmEthernetMgmtPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.9.1.3
This object represents the Administrative State of the Ethernet Management Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmEthernetMgmtPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.9.1.4
This object represents the Operational State of the Ethernet Management Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmEthernetMgmtPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.9.1.5
This object represents the Secondary State of the Ethernet Management Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmEthernetMgmtPortMTU 1.3.6.1.4.1.2544.1.12.4.1.9.1.6
This object provides the MTU on the Ethernet Management Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetMgmtPortConfigSpeed 1.3.6.1.4.1.2544.1.12.4.1.9.1.7
This object allows to configure the speed of the Ethernet Management Port.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetPortSpeed  

cmEthernetMgmtPortNegotiatedSpeed 1.3.6.1.4.1.2544.1.12.4.1.9.1.8
This object provides the negotiated speed of the Ethernet Management Port.
Status: current Access: read-only
OBJECT-TYPE    
  EthernetPortSpeed  

cmEthernetMgmtPortMDIXType 1.3.6.1.4.1.2544.1.12.4.1.9.1.9
This object allows management of MDIX property on Ethernet Management Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetMDIXType  

cmEthernetMgmtPortMDIXStatus 1.3.6.1.4.1.2544.1.12.4.1.9.1.10
This object provides the current MDIX status of the Ethernet Management port.
Status: current Access: read-only
OBJECT-TYPE    
  CmEthernetMDIXType  

cmEthernetMgmtPortMediaType 1.3.6.1.4.1.2544.1.12.4.1.9.1.11
This object represents the type of Ethernet Media on the Ethernet Management Port.
Status: current Access: read-only
OBJECT-TYPE    
  EthernetMediaType  

cmPrioMapTable 1.3.6.1.4.1.2544.1.12.4.1.10
A list of entries corresponding to Ethernet Priority Mappings in multi Class of Service (COS) mode. This table is applicable only when the Access Port is in connection-oriented evpl mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmPrioMapEntry

cmPrioMapEntry 1.3.6.1.4.1.2544.1.12.4.1.10.1
A conceptual row in the cmPrioMapTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmPrioMapEntry  

cmPrioMapIndex 1.3.6.1.4.1.2544.1.12.4.1.10.1.1
The integer index value corresponding to a priority value based on the cmEthernetAccPortPrioMapMode. In case of TOS and 8021P, valid indices are 1 to 8, in case of DSCP, valid indices are 1 to 64.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..64  

cmPrioMapInPriority 1.3.6.1.4.1.2544.1.12.4.1.10.1.2
The integer index value corresponding to a priority value based on the cmEthernetAccPortPrioMapMode. In case of TOS and 8021P, valid indices are 0 to 7, in case of DSCP, valid indices are 0 to 63.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..63  

cmPrioMapXTagControl 1.3.6.1.4.1.2544.1.12.4.1.10.1.3
This allows specification of whether the priority of incoming X-TAG should be swapped with cmPrioMapXTagPriority.
Status: current Access: read-write
OBJECT-TYPE    
  PrioMapControlType  

cmPrioMapXTagPriority 1.3.6.1.4.1.2544.1.12.4.1.10.1.4
This allows specification of the VLAN priority that will replace the incoming X-TAG's priority. This is applicable with cmPrioMapXTagControl as 'swap'.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmPrioMapCOS 1.3.6.1.4.1.2544.1.12.4.1.10.1.5
This allows specification of the COS Priority, i.e. this helps in determining the appropriate COS Policer for the Flow.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmPrioMapOuterTagPriority 1.3.6.1.4.1.2544.1.12.4.1.10.1.6
This allows specification of the VLAN priority that will replace the outgoing (A2N direction) outer-tag's priority. Note that, each flow participates or not in outer-tag priority mapping, using the object 'cmFlowOuterTagPrioEnabled'.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmPrioMapInnerTagPriority 1.3.6.1.4.1.2544.1.12.4.1.10.1.7
This allows specification of the VLAN priority that will replace the outgoing (A2N direction) inner-tag's (i.e. second tag) priority. Note that, each flow participates or not in inner-tag priority mapping, using the object 'cmFlowInnerTagPrioEnabled'.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmQosFlowPolicerTable 1.3.6.1.4.1.2544.1.12.4.1.11
A list of entries corresponding to Ethernet Quality of Service Policer for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmQosFlowPolicerEntry

cmQosFlowPolicerEntry 1.3.6.1.4.1.2544.1.12.4.1.11.1
A conceptual row in the cmQosFlowPolicerTable. These entries represent a Quality of Service Policer.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmQosFlowPolicerEntry  

cmQosFlowPolicerTypeIndex 1.3.6.1.4.1.2544.1.12.4.1.11.1.1
The unique index value corresponding to a Quality of Service Policer's direction. Values 1 and 2 are applicable to the Access Flow Policer - value of 1 stands for A2N direction, - value of 2 stands for N2A direction. Values 3 and 4 are applicable to Pass-thru Flow Policer (new in 5.6CC release): - value of 3 stands for N1toN2 direction - value of 4 stands for N2toN1 direction
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..4  

cmQosFlowPolicerIndex 1.3.6.1.4.1.2544.1.12.4.1.11.1.2
The Policer Index that represents the COS level. This is applicable in case of a Multi COS flow. Index 1 represents COS 0; Index 2 represents COS 1 and so on. In release 5.6CC the range is extended to 1..16 to support duplicate N2A policers on a Flow. The duplicate policers are created under a Flow if network interface of the Flow is ERP Group or Split Horizon Group. In case of multi-cos Flow indices 1..8 represent policers of COS 0..7 going from Network 1 port; indices 9..16 represent policers for COS 0..7 going from Network 2 port. In case of single-cos Flow index 1 represents policer going from Network 1 port; index 9 represents policer going from Network 2 port.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..16  

cmQosFlowPolicerDirection 1.3.6.1.4.1.2544.1.12.4.1.11.1.3
This object is allows specification of Policer direction as 'a2n' or 'n2a'.
Status: current Access: read-create
OBJECT-TYPE    
  TrafficDirection  

cmQosFlowPolicerAdminState 1.3.6.1.4.1.2544.1.12.4.1.11.1.4
This object represents the Administrative State of the QOS Flow Policer.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmQosFlowPolicerOperationalState 1.3.6.1.4.1.2544.1.12.4.1.11.1.5
This object represents the Operational State of the QOS Flow Policer.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmQosFlowPolicerSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.11.1.6
This object represents the Secondary State of the QOS Flow Policer.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmQosFlowPolicerCIRLo 1.3.6.1.4.1.2544.1.12.4.1.11.1.7
This object allows specification of the Commited Information Rate(CIR) on Policer. This represents the lower 32 bits of the CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosFlowPolicerCIRHi 1.3.6.1.4.1.2544.1.12.4.1.11.1.8
This object allows specification of the Commited Information Rate(CIR) on Policer. This represents the upper 32 bits of the CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosFlowPolicerEIRLo 1.3.6.1.4.1.2544.1.12.4.1.11.1.9
This object allows specification of the Excess Information Rate(EIR) on the Policer. This represents the lower 32 bits of the EIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosFlowPolicerEIRHi 1.3.6.1.4.1.2544.1.12.4.1.11.1.10
This object allows specification of the Excess Information Rate(EIR) on the Policer. This represents the upper 32 bits of the EIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosFlowPolicerCBS 1.3.6.1.4.1.2544.1.12.4.1.11.1.11
This object allows specification of the Commited Burst Size (CBS) on Policer.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cmQosFlowPolicerEBS 1.3.6.1.4.1.2544.1.12.4.1.11.1.12
This object allows specification of the Excess Burst Size (EBS) on the Policer.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cmQosFlowPolicerAlgorithm 1.3.6.1.4.1.2544.1.12.4.1.11.1.13
This object allows specification of Policer algorithm as 'srTCM' (Single Rate Triple Color Marking) or 'trTCM' (Two Rate Triple Color Marking).
Status: current Access: read-only
OBJECT-TYPE    
  PolicerAlgorithmType  

cmQosFlowPolicerColorMode 1.3.6.1.4.1.2544.1.12.4.1.11.1.14
This object allows specification of Policer Color Mode as 'color-aware' or 'color-blind'.
Status: current Access: read-create
OBJECT-TYPE    
  PolicerColorMode  

cmQosFlowPolicerColorMarkingFlag 1.3.6.1.4.1.2544.1.12.4.1.11.1.15
This object allows specification of Policer Color Marking Flag. The policer will set/clear the DEI (Drop Eligibility Indication) bit of the frame on an S-TAG if this flag is enabled. This object is not supported - setting any value will not have effect on the System.
Status: deprecated Access: read-create
OBJECT-TYPE    
  TruthValue  

cmQosFlowPolicerCouplingFlag 1.3.6.1.4.1.2544.1.12.4.1.11.1.16
This object allows specification of Policer Coupling Flag. When coupling is enabled, tokens that would normally be added to the C-bucket are passed to the E-bucket only once the CIR bucket has reached its CBS level. Therefore under this condition the E-bucket is being filled at the rate of CIR + EIR. Normally the long term average of frames declared yellow is bounded by the EIR. Coupling is a function to allow the long term average of frames declared yellow to be bounded by CIR + EIR. This allows a higher volume of yellow frames to be delivered/received if the arrival of green marked frames is low. Tokens from the E-bucket do NOT get passed to the C-bucket once the EBS level has been reached. Enabling coupling in combination with a provisioned EIR of 0 allows for a single rate three color marking (srTCM) algorithm to be established. In this situation the E-bucket is filled at the CIR rate in the case the C-bucket is filled to its CBS level.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmQosFlowPolicerAssociatedShaper 1.3.6.1.4.1.2544.1.12.4.1.11.1.17
This object allows specification of the QOS Shaper associated with this Policer. Multiple Policers can map to single Shaper. The corresponding row with the specified QOS value must exist in cmQosShaperTable when this value is specified.
Status: current Access: read-create
OBJECT-TYPE    
  VariablePointer  

cmQosFlowPolicerStorageType 1.3.6.1.4.1.2544.1.12.4.1.11.1.18
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmQosFlowPolicerRowStatus 1.3.6.1.4.1.2544.1.12.4.1.11.1.19
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmQosFlowPolicerRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmQosFlowPolicerRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmQosFlowPolicerRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmAccPortQosShaperTable 1.3.6.1.4.1.2544.1.12.4.1.12
A list of entries corresponding to Ethernet Access Port Quality of Service Shaper for configuration purposes. These shapers can be managed when the Access Port is in evpl mode and are relevant for traffic in the network to access direction.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmAccPortQosShaperEntry

cmAccPortQosShaperEntry 1.3.6.1.4.1.2544.1.12.4.1.12.1
A conceptual row in the cmAccPortQosShaperTable. These entries represent a Quality of Service Shaper.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmAccPortQosShaperEntry  

cmAccPortQosShaperIndex 1.3.6.1.4.1.2544.1.12.4.1.12.1.1
The unique integer index value corresponding to a Quality of Service Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..8  

cmAccPortQosShaperDirection 1.3.6.1.4.1.2544.1.12.4.1.12.1.2
The direction of the Quality of Service Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  TrafficDirection  

cmAccPortQosShaperAdminState 1.3.6.1.4.1.2544.1.12.4.1.12.1.3
This object represents the Administrative State of the QOS Shaper.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmAccPortQosShaperOperationalState 1.3.6.1.4.1.2544.1.12.4.1.12.1.4
This object represents the Operational State of the QOS Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmAccPortQosShaperSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.12.1.5
This object represents the Secondary State of the QOS Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmAccPortQosShaperCIRLo 1.3.6.1.4.1.2544.1.12.4.1.12.1.6
This object represents the Commited Information Rate(CIR) (Lower 32 bits)of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperCIRHi 1.3.6.1.4.1.2544.1.12.4.1.12.1.7
This object represents the Commited Information Rate(CIR) (Higher 32 bits) of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperEIRLo 1.3.6.1.4.1.2544.1.12.4.1.12.1.8
This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperEIRHi 1.3.6.1.4.1.2544.1.12.4.1.12.1.9
This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperCBS 1.3.6.1.4.1.2544.1.12.4.1.12.1.10
This object represents the Commited Burst Size (CBS) of the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperEBS 1.3.6.1.4.1.2544.1.12.4.1.12.1.11
This object represents the Excess Burst Size (EBS) of the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperBufferSize 1.3.6.1.4.1.2544.1.12.4.1.12.1.12
This object represents the Buffer Size of the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperCOS 1.3.6.1.4.1.2544.1.12.4.1.12.1.13
This object provides the COS (Class of Service) value for the QOS Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

cmAccPortQosShaperSoamCIRLo 1.3.6.1.4.1.2544.1.12.4.1.12.1.14
This object represents the Soam Commited Information Rate(SOAM-CIR) (Lower 32 bits)of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperSoamCIRHi 1.3.6.1.4.1.2544.1.12.4.1.12.1.15
This object represents the Soam Commited Information Rate(SOAM-CIR) (Higher 32 bits) of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperSoamEIRLo 1.3.6.1.4.1.2544.1.12.4.1.12.1.16
This object represents the Soam Excess Information Rate(SOAM-EIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperSoamEIRHi 1.3.6.1.4.1.2544.1.12.4.1.12.1.17
This object represents the Soam Excess Information Rate(SOAM-EIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperWredGreenMinQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.12.1.18
This object represents the Wred green packet min queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperWredGreenMaxQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.12.1.19
This object represents the Wred green packet max queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperWredGreenDropProbability 1.3.6.1.4.1.2544.1.12.4.1.12.1.20
This object represents the Wred green packet drop probability.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperWredYellowMinQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.12.1.21
This object represents the Wred yellow packet min queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperWredYellowMaxQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.12.1.22
This object represents the Wred yellow packet max queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmAccPortQosShaperWredYellowDropProbability 1.3.6.1.4.1.2544.1.12.4.1.12.1.23
This object represents the Wred yellow packet drop probability.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmEthernetAccPortCpdV2Table 1.3.6.1.4.1.2544.1.12.4.1.13
A list of entries corresponding to Ethernet Access Port Control Protocol Disposition (CPD) V2. This support of CPD is provided on the GE206/GE201 device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetAccPortCpdV2Entry

cmEthernetAccPortCpdV2Entry 1.3.6.1.4.1.2544.1.12.4.1.13.1
A conceptual row in the cmEthernetAccPortCpdV2Table. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Access Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetAccPortCpdV2Entry  

cmEthernetAccPortCpdV2Index 1.3.6.1.4.1.2544.1.12.4.1.13.1.1
Unique Index value to access the CPD row.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortCpdV2CiscoGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.2
Deprecated - each Cisco protocol has its own disposition. Control Protocol Disposition for Cisco Group. This includes ISL, PAGP, UDLD, CDP, VTP, DTP, PSVTP+, UplinkFast, VLAN Bridge, L2PT. Note that a specific protocol filter overrides the group setting.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2IslDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.3
Control Protocol Disposition for ISL (Inter Switch Link). MAC Address (01:00:0C:00:00:00).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2PagpDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.4
Control Protocol Disposition for PAGP (Port Aggregation Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x104).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2UdldDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.5
Control Protocol Disposition for UDLD (Unidirectional Link Detection). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x111).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2CdpDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.6
Control Protocol Disposition for CDP (Cisco Discovery Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2000).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2VtpDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.7
Control Protocol Disposition for VTP (VLAN Trunking Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2003).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2DtpDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.8
Control Protocol Disposition for DTP (Dynamic Trunking). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2004).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2PvstpPlusDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.9
Control Protocol Disposition for Spanning Tree PVSTP+. MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x10B).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2UplinkFastDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.10
Control Protocol Disposition for STP UplinkFast. MAC Address (01:00:0C:CD:CD:CD), Ethertype(0x200A).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2VlanBridgeDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.11
Control Protocol Disposition for VLAN Bridge. MAC Address (01:00:0C:CD:CD:CE), Ethertype(0x10C).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2L2PTDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.12
Control Protocol Disposition for Layer 2 Protocol Tunnelling(L2PT). MAC Address (01:00:0C:CD:CD:D0).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2BridgeGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.13
Deprecated - individual dispositions available for each MAC. Bridge Group Control Protocol Disposition Type. This includes BPDU, PAUSE (IEEE 802.3x Flow Control), LACP (Link Aggregation), LACP Marker (Marker), EFM OAM (IEEE 802.3 ah) and IEEE 802.1x Port Authentication, besides reserved MAC addresses from 01:80:C2:00:00:04 thru 01:80:C2:00:00:0F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2BPDUDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.14
Control Protocol Disposition for IEEE Spanning Tree(STP), MSTP (Multiple Spanning Tree) and RSTP (Rapid Reconfiguration of Spanning Tree). MAC Address (01:80:C2:00:00:00).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2PauseDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.15
Control Protocol Disposition for IEEE 802.3x Flow Control (PAUSE frames).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2LACPDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.16
Control Protocol Disposition for 802.3ad Link Aggregation Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(01).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2LACPMarkerDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.17
Control Protocol Disposition for IEEE 802.3ad Marker Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(02).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2EfmOamDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.18
Control Protocol Disposition for IEEE 802.3ah EFM OAM. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(03).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2SSMDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.19
Control Protocol Disposition for Sync Status Messages. MAC Address (01:80:C2:00:00:02), Ethertype (0x19A7), Subtype(0A).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2PortAuthenDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.20
Control Protocol Disposition for IEEE 802.1x Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x888E).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2BridgeReservedDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.21
Deprecated - individual dispositions available for each MAC. Control Protocol Disposition for Range of MAC Addresses from 01:80:C2:00:00:04 to 01:80:C2:00:00:0F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2LANBridgesDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.22
Control Protocol Disposition for IEEE 802.1d LAN Bridge Managment. MAC Address (01:80:C2:00:00:10).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2GARPGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.23
Deprecated - each GARP Group protocol has its own disposition. Group Disposition type which includes GMRP, GVRP and MAC Address from range 01:80:C2:00:00:20 to 01:80:C2:00:00:2F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2GMRPDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.24
Control Protocol Disposition for GARP Multicast Registration Protocol. MAC Address (01:80:C2:00:00:20).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2GVRPDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.25
Control Protocol Disposition for GARP VLAN Registration Protocol. MAC Address (01:80:C2:00:00:21).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2GARPDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.26
Group Disposition type which includes GARP Reserved MAC Address from range 01:80:C2:00:00:22 to 01:80:C2:00:00:2F.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2LLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.27
Deprecated - each LLDP MAC protocol has its own disposition. LLDP (Link Layer Discovery Protocol) Disposition type. MAC Address 01:80:C2:00:00:0e, 01:80:C2:00:00:03, or 01:80:C2:00:00:00.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2ELMIDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.28
ELMI (Ethernet Local Management Interface) Disposition type. MAC Address 01:80:C2:00:00:07 and EtherType of 0x88EE.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2L2PTTunnelMac 1.3.6.1.4.1.2544.1.12.4.1.13.1.29
Configurable Layer 2 Protocol Tunneling MAC Address. For protocols STP, CDP and VTP, with control protocol disposition as pass-thru-l2pt, this configured MAC address replaces the DA, upon encapsulation. For decapsulation, protocol signature and this configured MAC address are matched and the MAC address is replaced with the protocol's inferred MAC address.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmEthernetAccPortCpdV2Mac00DispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.30
MAC Address 01:80:C2:00:00:00 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac01DispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.31
MAC Address 01:80:C2:00:00:01 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac02DispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.32
MAC Address 01:80:C2:00:00:02 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac03DispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.33
MAC Address 01:80:C2:00:00:03 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac04DispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.34
MAC Address 01:80:C2:00:00:04 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac05DispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.35
MAC Address 01:80:C2:00:00:05 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac06DispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.36
MAC Address 01:80:C2:00:00:06 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac07DispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.37
MAC Address 01:80:C2:00:00:07 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac08DispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.38
MAC Address 01:80:C2:00:00:08 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac09DispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.39
MAC Address 01:80:C2:00:00:09 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac0ADispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.40
MAC Address 01:80:C2:00:00:0A Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac0BDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.41
MAC Address 01:80:C2:00:00:0B Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac0CDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.42
MAC Address 01:80:C2:00:00:0C Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac0DDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.43
MAC Address 01:80:C2:00:00:0D Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac0EDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.44
MAC Address 01:80:C2:00:00:0E Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2Mac0FDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.45
MAC Address 01:80:C2:00:00:0F Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2NearestLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.46
LLDP (Link Layer Discovery Protocol) Nearest Bridge Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2NonTpmrLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.47
LLDP (Link Layer Discovery Protocol) Non-TPMR Bridge Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2CustomerLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.48
LLDP (Link Layer Discovery Protocol) Customer Bridge Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2PtpUntaggedDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.49
PTP untagged frame Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetAccPortCpdV2PtpTaggedDispType 1.3.6.1.4.1.2544.1.12.4.1.13.1.50
PTP tagged frame Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Table 1.3.6.1.4.1.2544.1.12.4.1.14
A list of entries corresponding to Ethernet Flow Control Protocol Disposition V2. This table is supported for the GE206/GE201 devices.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmFlowCpdV2Entry

cmFlowCpdV2Entry 1.3.6.1.4.1.2544.1.12.4.1.14.1
A conceptual row in the cmFlowCpdV2Table. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Flow.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmFlowCpdV2Entry  

cmFlowCpdV2Index 1.3.6.1.4.1.2544.1.12.4.1.14.1.1
Unique Index value to access the CPD row.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmFlowCpdV2CiscoGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.2
Deprecated - each Cisco protocol has its own disposition. Control Protocol Disposition for Cisco Group. This includes ISL, PAGP, UDLD, CDP, VTP, DTP, PSVTP+, UplinkFast, VLAN Bridge, L2PT. Note that a specific protocol filter overrides the group setting.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2IslDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.3
Control Protocol Disposition for ISL (Inter Switch Link). MAC Address (01:00:0C:00:00:00).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2PagpDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.4
Control Protocol Disposition for PAGP (Port Aggregation Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x104).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2UdldDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.5
Control Protocol Disposition for UDLD (Unidirectional Link Detection). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x111).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2CdpDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.6
Control Protocol Disposition for CDP (Cisco Discovery Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2000).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2VtpDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.7
Control Protocol Disposition for VTP (VLAN Trunking Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2003).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2DtpDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.8
Control Protocol Disposition for DTP (Dynamic Trunking). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2004).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2PvstpPlusDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.9
Control Protocol Disposition for Spanning Tree PVSTP+. MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x10B).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2UplinkFastDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.10
Control Protocol Disposition for STP UplinkFast. MAC Address (01:00:0C:CD:CD:CD), Ethertype(0x200A).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2VlanBridgeDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.11
Control Protocol Disposition for VLAN Bridge. MAC Address (01:00:0C:CD:CD:CE), Ethertype(0x10C).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2L2PTDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.12
Control Protocol Disposition for Layer 2 Protocol Tunnelling(L2PT). MAC Address (01:00:0C:CD:CD:D0).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2BridgeGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.13
Deprecated - individual dispositions available for each MAC. Bridge Group Control Protocol Disposition Type. This includes BPDU, PAUSE (IEEE 802.3x Flow Control), LACP (Link Aggregation), LACP Marker (Marker), EFM OAM (IEEE 802.3 ah) and IEEE 802.1x Port Authentication, besides reserved MAC addresses from 01:80:C2:00:00:04 thru 01:80:C2:00:00:0F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2BPDUDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.14
Control Protocol Disposition for IEEE Spanning Tree(STP), MSTP (Multiple Spanning Tree) and RSTP (Rapid Reconfiguration of Spanning Tree). MAC Address (01:80:C2:00:00:00).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2PauseDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.15
Control Protocol Disposition for IEEE 802.3x Flow Control (PAUSE frames).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2LACPDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.16
Control Protocol Disposition for 802.3ad Link Aggregation Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(01).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2LACPMarkerDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.17
Control Protocol Disposition for IEEE 802.3ad Marker Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(02).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2EfmOamDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.18
Control Protocol Disposition for IEEE 802.3ah EFM OAM. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(03).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2SSMDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.19
Control Protocol Disposition for Sync Status Messages. MAC Address (01:80:C2:00:00:02), Ethertype (0x19A7), Subtype(0A).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2PortAuthenDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.20
Control Protocol Disposition for IEEE 802.1x Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x888E).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2BridgeReservedDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.21
Deprecated - individual dispositions available for each MAC. Control Protocol Disposition for Range of MAC Addresses from 01:80:C2:00:00:04 to 01:80:C2:00:00:0F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2LANBridgesDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.22
Control Protocol Disposition for IEEE 802.1d LAN Bridge Managment. MAC Address (01:80:C2:00:00:10).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2GARPGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.23
Deprecated - each GARP Group protocol has its own disposition. Group Disposition type which includes GMRP, GVRP and MAC Address from range 01:80:C2:00:00:20 to 01:80:C2:00:00:2F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2GMRPDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.24
Control Protocol Disposition for GARP Multicast Registration Protocol. MAC Address (01:80:C2:00:00:20).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2GVRPDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.25
Control Protocol Disposition for GARP VLAN Registration Protocol. MAC Address (01:80:C2:00:00:21).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2GARPDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.26
Group Disposition type which includes GARP Reserved MAC Address from range 01:80:C2:00:00:22 to 01:80:C2:00:00:2F.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2ActiveControlProtocols 1.3.6.1.4.1.2544.1.12.4.1.14.1.27
List of Active Control Protocol Dispositions. Note that if the Port Level Disposition control is set to PEER or DISCARD, the flow level disposition is no longer active. This object provides information on all the active dispositions.
Status: current Access: read-only
OBJECT-TYPE    
  CmActiveControlProtocolsType  

cmFlowCpdV2LLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.28
Deprecated - each LLDP MAC protocol has its own disposition. LLDP (Link Layer Discovery Protocol) Disposition type. MAC Address 01:80:C2:00:00:0e, 01:80:C2:00:00:03, or 01:80:C2:00:00:00.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2ELMIDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.29
ELMI (Ethernet Local Management Interface) Disposition type. MAC Address 01:80:C2:00:00:07 and EtherType of 0x88EE.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac00DispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.30
MAC Address 01:80:C2:00:00:00 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac01DispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.31
MAC Address 01:80:C2:00:00:01 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac02DispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.32
MAC Address 01:80:C2:00:00:02 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac03DispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.33
MAC Address 01:80:C2:00:00:03 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac04DispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.34
MAC Address 01:80:C2:00:00:04 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac05DispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.35
MAC Address 01:80:C2:00:00:05 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac06DispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.36
MAC Address 01:80:C2:00:00:06 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac07DispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.37
MAC Address 01:80:C2:00:00:07 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac08DispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.38
MAC Address 01:80:C2:00:00:08 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac09DispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.39
MAC Address 01:80:C2:00:00:09 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac0ADispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.40
MAC Address 01:80:C2:00:00:0A Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac0BDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.41
MAC Address 01:80:C2:00:00:0B Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac0CDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.42
MAC Address 01:80:C2:00:00:0C Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac0DDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.43
MAC Address 01:80:C2:00:00:0D Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac0EDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.44
MAC Address 01:80:C2:00:00:0E Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2Mac0FDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.45
MAC Address 01:80:C2:00:00:0F Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2NearestLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.46
LLDP (Link Layer Discovery Protocol) Nearest Bridge Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2NonTpmrLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.47
LLDP (Link Layer Discovery Protocol) Non-TPMR Bridge Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowCpdV2CustomerLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.14.1.48
LLDP (Link Layer Discovery Protocol) Customer Bridge Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Table 1.3.6.1.4.1.2544.1.12.4.1.15
A list of entries corresponding to Ethernet Network Port Control Protocol Disposition V2. This table is supported for the GE206/GE201 devices.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetNetPortCpdV2Entry

cmEthernetNetPortCpdV2Entry 1.3.6.1.4.1.2544.1.12.4.1.15.1
A conceptual row in the cmEthernetNetPortCpdV2Table. These entries represent a Control Protocol Disposition filtering criteria on the Ethernet Network Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetNetPortCpdV2Entry  

cmEthernetNetPortCpdV2Index 1.3.6.1.4.1.2544.1.12.4.1.15.1.1
Unique Index value to access the CPD row.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetNetPortCpdV2CiscoGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.2
Deprecated - each Cisco protocol has its own disposition. Control Protocol Disposition for Cisco Group. This includes ISL, PAGP, UDLD, CDP, VTP, DTP, PSVTP+, UplinkFast, VLAN Bridge, L2PT. Note that a specific protocol filter overrides the group setting.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2IslDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.3
Control Protocol Disposition for ISL (Inter Switch Link). MAC Address (01:00:0C:00:00:00).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2PagpDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.4
Control Protocol Disposition for PAGP (Port Aggregation Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x104).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2UdldDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.5
Control Protocol Disposition for UDLD (Unidirectional Link Detection). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x111).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2CdpDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.6
Control Protocol Disposition for CDP (Cisco Discovery Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2000).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2VtpDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.7
Control Protocol Disposition for VTP (VLAN Trunking Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2003).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2DtpDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.8
Control Protocol Disposition for DTP (Dynamic Trunking). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2004).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2PvstpPlusDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.9
Control Protocol Disposition for Spanning Tree PVSTP+. MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x10B).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2UplinkFastDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.10
Control Protocol Disposition for STP UplinkFast. MAC Address (01:00:0C:CD:CD:CD), Ethertype(0x200A).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2VlanBridgeDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.11
Control Protocol Disposition for VLAN Bridge. MAC Address (01:00:0C:CD:CD:CE), Ethertype(0x10C).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2L2PTDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.12
Control Protocol Disposition for Layer 2 Protocol Tunnelling(L2PT). MAC Address (01:00:0C:CD:CD:D0).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2BridgeGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.13
Deprecated - individual dispositions available for each MAC. Bridge Group Control Protocol Disposition Type. This includes BPDU, PAUSE (IEEE 802.3x Flow Control), LACP (Link Aggregation), LACP Marker (Marker), EFM OAM (IEEE 802.3 ah) and IEEE 802.1x Port Authentication, besides reserved MAC addresses from 01:80:C2:00:00:04 thru 01:80:C2:00:00:0F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2BPDUDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.14
Control Protocol Disposition for IEEE Spanning Tree(STP), MSTP (Multiple Spanning Tree) and RSTP (Rapid Reconfiguration of Spanning Tree). MAC Address (01:80:C2:00:00:00).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2PauseDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.15
Control Protocol Disposition for IEEE 802.3x Flow Control (PAUSE frames).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2LACPDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.16
Control Protocol Disposition for 802.3ad Link Aggregation Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(01).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2LACPMarkerDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.17
Control Protocol Disposition for IEEE 802.3ad Marker Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(02).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2EfmOamDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.18
Control Protocol Disposition for IEEE 802.3ah EFM OAM. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(03).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2SSMDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.19
Control Protocol Disposition for Sync Status Messages. MAC Address (01:80:C2:00:00:02), Ethertype (0x19A7), Subtype(0A).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2PortAuthenDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.20
Control Protocol Disposition for IEEE 802.1x Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x888E).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2BridgeReservedDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.21
Deprecated - individual dispositions available for each MAC. Control Protocol Disposition for Range of MAC Addresses from 01:80:C2:00:00:04 to 01:80:C2:00:00:0F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2LANBridgesDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.22
Control Protocol Disposition for IEEE 802.1d LAN Bridge Managment. MAC Address (01:80:C2:00:00:10).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2GARPGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.23
Deprecated - each GARP Group protocol has its own disposition. Group Disposition type which includes GMRP, GVRP and MAC Address from range 01:80:C2:00:00:20 to 01:80:C2:00:00:2F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2GMRPDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.24
Control Protocol Disposition for GARP Multicast Registration Protocol. MAC Address (01:80:C2:00:00:20).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2GVRPDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.25
Control Protocol Disposition for GARP VLAN Registration Protocol. MAC Address (01:80:C2:00:00:21).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2GARPDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.26
Group Disposition type which includes GARP Reserved MAC Address from range 01:80:C2:00:00:22 to 01:80:C2:00:00:2F.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2LLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.27
Deprecated - each LLDP MAC protocol has its own disposition. LLDP (Link Layer Discovery Protocol) Disposition type. MAC Address 01:80:C2:00:00:0e, 01:80:C2:00:00:03, or 01:80:C2:00:00:00.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2ELMIDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.28
ELMI (Ethernet Local Management Interface) Disposition type. MAC Address 01:80:C2:00:00:07 and EtherType of 0x88EE.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2L2PTTunnelMac 1.3.6.1.4.1.2544.1.12.4.1.15.1.29
Configurable Layer 2 Protocol Tunneling MAC Address. For protocols STP, CDP and VTP, with control protocol disposition as pass-thru-l2pt, this configured MAC address replaces the DA, upon encapsulation. For decapsulation, protocol signature and this configured MAC address are matched and the MAC address is replaced with the protocol's inferred MAC address.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmEthernetNetPortCpdV2Mac00DispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.30
MAC Address 01:80:C2:00:00:00 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac01DispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.31
MAC Address 01:80:C2:00:00:01 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac02DispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.32
MAC Address 01:80:C2:00:00:02 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac03DispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.33
MAC Address 01:80:C2:00:00:03 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac04DispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.34
MAC Address 01:80:C2:00:00:04 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac05DispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.35
MAC Address 01:80:C2:00:00:05 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac06DispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.36
MAC Address 01:80:C2:00:00:06 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac07DispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.37
MAC Address 01:80:C2:00:00:07 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac08DispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.38
MAC Address 01:80:C2:00:00:08 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac09DispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.39
MAC Address 01:80:C2:00:00:09 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac0ADispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.40
MAC Address 01:80:C2:00:00:0A Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac0BDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.41
MAC Address 01:80:C2:00:00:0B Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac0CDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.42
MAC Address 01:80:C2:00:00:0C Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac0DDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.43
MAC Address 01:80:C2:00:00:0D Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac0EDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.44
MAC Address 01:80:C2:00:00:0E Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2Mac0FDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.45
MAC Address 01:80:C2:00:00:0F Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2NearestLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.46
LLDP (Link Layer Discovery Protocol) Nearest Bridge Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2NonTpmrLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.47
LLDP (Link Layer Discovery Protocol) Non-TPMR Bridge Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2CustomerLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.48
LLDP (Link Layer Discovery Protocol) Customer Bridge Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2PtpUntaggedDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.49
PTP non forwarding untagged frame Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetNetPortCpdV2PtpTaggedDispType 1.3.6.1.4.1.2544.1.12.4.1.15.1.50
PTP tagged frame Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

bitsPortTable 1.3.6.1.4.1.2544.1.12.4.1.16
A list of entries corresponding to BITS Port Facilities for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BitsPortEntry

bitsPortEntry 1.3.6.1.4.1.2544.1.12.4.1.16.1
A conceptual row in the bitsPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BitsPortEntry  

bitsPortTypeIndex 1.3.6.1.4.1.2544.1.12.4.1.16.1.1
An integer index value used to uniquely identify this BITS Port within the card. Value 1 stands for BITS-IN, 2 for BITS-OUT.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

bitsPortIndex 1.3.6.1.4.1.2544.1.12.4.1.16.1.2
An integer index value used to uniquely identify this BITS Port within the card. Note that each BITs Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, bitsPortIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

bitsPortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.16.1.3
This object has the same value as ifIndex for Bits Port. An integer index value used to uniquely identify this Bits Port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

bitsPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.16.1.4
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

bitsPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.16.1.5
This object represents the Administrative State of the BITS Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

bitsPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.16.1.6
This object represents the Operational State of the BITS Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

bitsPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.16.1.7
This object represents the Secondary State of the BITS Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

bitsPortType 1.3.6.1.4.1.2544.1.12.4.1.16.1.8
This object represents the BITS Port Type.
Status: current Access: read-only
OBJECT-TYPE    
  BitsPortType  

bitsPortLineType 1.3.6.1.4.1.2544.1.12.4.1.16.1.9
This object represents the BITS Port Line Type. Determines whether the T1/E1 BITS port operates in T1, E1, or 2048kHz mode.
Status: current Access: read-write
OBJECT-TYPE    
  BitsPortLineType  

bitsPortLineCode 1.3.6.1.4.1.2544.1.12.4.1.16.1.10
This object represents the BITS Port Line Code. When the port is configured for a Line Type of T1, the valid values are t1-b8zs and t1-ami and the default value is t1-b8zs. When the port is configured for a Line Type of E1, the valid values are e1-hdb3 and e1-ami and the default value is e1-hdb3. When the port is configured for a Line Type of 2048kHz, the value is none.
Status: current Access: read-write
OBJECT-TYPE    
  BitsPortLineCode  

bitsPortFrameFormat 1.3.6.1.4.1.2544.1.12.4.1.16.1.11
This object represents the BITS Port Frame Format. When the port is configured for a Line Type of T1, the valid values are t1-sf and t1-esf and the default value is t1-esf. When the port is configured for a Line Type of E1, the valid values are e1-unframed, e1-crc4, and e1-dualFrame and the default value is e1-crc4. When the port is configured for a Line Type of 2048kHz, the value is none. R4.1CC and R4.3CC do not support e1-unframed.
Status: current Access: read-write
OBJECT-TYPE    
  BitsFrameFormat  

bitsPortSaBitDesignation 1.3.6.1.4.1.2544.1.12.4.1.16.1.12
This object represents the BITS Port Sa Bit Designation. Determines which E1 Sa Bit is used to transmit/receive the SSM. For T1 and 2048khz Line Types, the only allowed value is None. For E1 Line Type, the default value is bit4 and it can only have a value of None if QL Mode is disabled, otherwise, None is an invalid value.
Status: current Access: read-write
OBJECT-TYPE    
  SaBitDesignation  

bitsPortQLModeEnabled 1.3.6.1.4.1.2544.1.12.4.1.16.1.13
This object allows to specify whether the BITS Port can be enabled/disabled for QL Mode. When enabled, on receive side -port shall PEER the SSM (Sync Status Messages) slow protocol PDUs and take appropriate action When enabled, on transmit side -port shall periodically (once a second) transmit QL TLV information PDUs When disabled, on receive side, -port shall terminate and discard any SSM slow protocol PDUs When disabled, on transmit side -port shall not transmit any SSM slow protocol PDUs.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

bitsPortExpectedQL 1.3.6.1.4.1.2544.1.12.4.1.16.1.14
This object allows to specify the expected QL when the BITS Port is enabled for QL Mode. This object allows the user to set a minimum expected received Quality Level on the port. The default value shall be None.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

bitsPortAssumedQL 1.3.6.1.4.1.2544.1.12.4.1.16.1.15
This object allows to specify the assumed QL on the BITS Port. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port's QL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

bitsPortReceivedQL 1.3.6.1.4.1.2544.1.12.4.1.16.1.16
This object provides the Received QL value for the BITS port. If the BITS port's QL Mode is disabled, then the received QL value is not applicable.
Status: current Access: read-only
OBJECT-TYPE    
  SSMQualityLevel  

bitsPortTransmitQL 1.3.6.1.4.1.2544.1.12.4.1.16.1.17
This object provides the Transmitted QL value for the BITS port. If the BITS port's QL Mode is disabled, then the received QL value is not applicable.
Status: current Access: read-only
OBJECT-TYPE    
  SSMQualityLevel  

bitsPortSquelchQL 1.3.6.1.4.1.2544.1.12.4.1.16.1.18
This object allows to set the Squelch QL for the BITS-OUT port. The Squelch QL is only meaningful if the QL Mode is Enabled. The Squelch QL is used to determine whether or not to squelch the output of the BITS-OUT port. If the system's QL is lower than the Squelch QL, the output is squelched. If the BITS port's QL Mode is disabled, then the received QL value is not applicable.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

bitsPortLineBuildOut 1.3.6.1.4.1.2544.1.12.4.1.16.1.19
This object allows to manage the line build out on the BITS-OUT port when the Line Type is T1.
Status: current Access: read-write
OBJECT-TYPE    
  LineBuildOut  

bitsPortImpedance 1.3.6.1.4.1.2544.1.12.4.1.16.1.20
This object provides the impedance mode for the BITS-OUT port.
Status: current Access: read-only
OBJECT-TYPE    
  BitsPortImpedanceMode  

ieee1588EthernetPortTable 1.3.6.1.4.1.2544.1.12.4.1.17
A list of entries corresponding to IEEE Ethernet Port Facilities for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IEEE1588EthernetPortEntry

ieee1588EthernetPortEntry 1.3.6.1.4.1.2544.1.12.4.1.17.1
A conceptual row in the IEEE Ethernet Port Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IEEE1588EthernetPortEntry  

ieee1588EthernetPortIndex 1.3.6.1.4.1.2544.1.12.4.1.17.1.1
An integer index value used to uniquely identify the IEEE Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ieee1588EthernetPortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.17.1.2
This object has the same value as ifIndex for the IEEE Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

ieee1588EthernetPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.17.1.3
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

ieee1588EthernetPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.17.1.4
This object represents the Administrative State of the Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

ieee1588EthernetPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.17.1.5
This object represents the Operational State of the Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

ieee1588EthernetPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.17.1.6
This object represents the Secondary State of the Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

ieee1588EthernetPortMTU 1.3.6.1.4.1.2544.1.12.4.1.17.1.7
This object provides the MTU on the Port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

ieee1588EthernetPortMediaType 1.3.6.1.4.1.2544.1.12.4.1.17.1.8
This object represents the type of Media.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetMediaType  

ieee1588EthernetPortConfigSpeed 1.3.6.1.4.1.2544.1.12.4.1.17.1.9
This object allows to configure the speed of the Port.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetPortSpeed  

ieee1588EthernetPortNegotiatedSpeed 1.3.6.1.4.1.2544.1.12.4.1.17.1.10
This object provides the negotiated speed of the Port.
Status: current Access: read-only
OBJECT-TYPE    
  EthernetPortSpeed  

ieee1588EthernetPortMDIXType 1.3.6.1.4.1.2544.1.12.4.1.17.1.11
This object allows management of MDIX property on Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetMDIXType  

gps10MHzPortTable 1.3.6.1.4.1.2544.1.12.4.1.18
A list of entries corresponding to GPS 10MHz Facilities for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GPS10MHzPortEntry

gps10MHzPortEntry 1.3.6.1.4.1.2544.1.12.4.1.18.1
A conceptual row in the GPS 10MHz Port Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  GPS10MHzPortEntry  

gps10MHzPortIndex 1.3.6.1.4.1.2544.1.12.4.1.18.1.1
An integer index value used to uniquely identify the IEEE Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

gps10MHzPortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.18.1.2
This object has the same value as ifIndex for the IEEE Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

gps10MHzPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.18.1.3
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

gps10MHzPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.18.1.4
This object represents the Administrative State of the Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

gps10MHzPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.18.1.5
This object represents the Operational State of the Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

gps10MHzPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.18.1.6
This object represents the Secondary State of the Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

gps10MHzPortSignalDirection 1.3.6.1.4.1.2544.1.12.4.1.18.1.7
This object allows specification of the signal type (i.e. input or output).
Status: current Access: read-write
OBJECT-TYPE    
  SignalDirectionType  

gps10MHzPortSquelchControl 1.3.6.1.4.1.2544.1.12.4.1.18.1.8
This object allows to set the Squelch Control for the 10MHz port. The Squelch Control is used to determine the type of squelch control used to squelch the output of the TOD port. Only option supported is squelch-ql.
Status: current Access: read-write
OBJECT-TYPE    
  SquelchControl  

gps10MHzPortSquelchQL 1.3.6.1.4.1.2544.1.12.4.1.18.1.9
This object allows to set the Squelch QL for the 10MHz port. This value is used when f310MHzClockPortSquelchControl is squelch-ql. The Squelch QL is used to determine whether or not to squelch the output of the TOD port. If the system's QL is lower than the Squelch QL, the output is squelched.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

gps10MHzPortFrequencySource 1.3.6.1.4.1.2544.1.12.4.1.18.1.10
This object allows to set the Frequency Source for the Port.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

gps10MHzPortClockClass 1.3.6.1.4.1.2544.1.12.4.1.18.1.11
This object specify GPS port clock class.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Unsigned32  

gps10MHzPortClockAccuracy 1.3.6.1.4.1.2544.1.12.4.1.18.1.12
This object specify GPS port clock accuracy.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Unsigned32  

gps10MHzPortTimeSource 1.3.6.1.4.1.2544.1.12.4.1.18.1.13
This object specify GPS port time source.
Status: deprecated Access: read-only
OBJECT-TYPE    
  TimeSource  

gps10MHzPortAssumedQL 1.3.6.1.4.1.2544.1.12.4.1.18.1.14
This object allows to specify the assumed QL on the GPS Port. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port's QL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

gps10MHzPortAlias 1.3.6.1.4.1.2544.1.12.4.1.18.1.15
This object allows SNMP management entities to provide an alias to the gps 10MHz Port entity.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

cmEthernetNetPortClbTable 1.3.6.1.4.1.2544.1.12.4.1.19
A list of entries corresponding to Ethernet Network Port Cable Length Benchmark.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetNetPortClbEntry

cmEthernetNetPortClbEntry 1.3.6.1.4.1.2544.1.12.4.1.19.1
A conceptual row in the cmEthernetNetPortClbTable. These entries represent Cable Length Benchmarks on the Ethernet Network Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetNetPortClbEntry  

cmEthernetNetPortClbIndex 1.3.6.1.4.1.2544.1.12.4.1.19.1.1
An integer index value used to uniquely identify this Cable Length Benchmark Entry specification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..5  

cmEthernetNetPortClbEnabled 1.3.6.1.4.1.2544.1.12.4.1.19.1.2
This enables specification of Cable Length Benchmark entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortClbLength 1.3.6.1.4.1.2544.1.12.4.1.19.1.3
Cable length of Cable Points Entry. The cable length is of the form XXX[.YY] where XX can be any integer value and YY allows precision of 2 decimals after the floating point. Note that .YY is optional.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cmEthernetNetPortClbDescr 1.3.6.1.4.1.2544.1.12.4.1.19.1.4
A textual string containing description of cable span.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

cmNetPortPrioMapTable 1.3.6.1.4.1.2544.1.12.4.1.20
A list of entries corresponding to Ethernet Network Port Priority Mappings in multi Class of Service (COS) mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmNetPortPrioMapEntry

cmNetPortPrioMapEntry 1.3.6.1.4.1.2544.1.12.4.1.20.1
A conceptual row in the cmNetPortPrioMapTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmNetPortPrioMapEntry  

cmNetPortPrioMapIndex 1.3.6.1.4.1.2544.1.12.4.1.20.1.1
The integer index value corresponding to a priority value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

cmNetPortPrioMapInPriority 1.3.6.1.4.1.2544.1.12.4.1.20.1.2
The integer index value corresponding to a priority value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmNetPortPrioMapCOS 1.3.6.1.4.1.2544.1.12.4.1.20.1.3
This allows specification of the COS Priority, i.e. this helps in determining the appropriate COS Policer for the Flow.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmNetPortPrioMapOuterTagPriority 1.3.6.1.4.1.2544.1.12.4.1.20.1.4
This allows specification of the VLAN priority that will replace the outgoing (N2A direction) outer-tag's priority. Note that, each flow participates or not in outer-tag priority mapping, using the object 'cmFlowN2AOuterTagPrioEnabled'.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmAccPortPcpDEEncTable 1.3.6.1.4.1.2544.1.12.4.1.21
Ethernet Access Port PCP drop eligibility encoding table. This is applied to a frame that is egressing at the Access port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmAccPortPcpDEEncEntry

cmAccPortPcpDEEncEntry 1.3.6.1.4.1.2544.1.12.4.1.21.1
A conceptual row in the ethernetPBPcpDEEncPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmAccPortPcpDEEncEntry  

cmAccPortPcpDEEncIndex 1.3.6.1.4.1.2544.1.12.4.1.21.1.1
An integer index value used to uniquely identify a row in the PCP drop eligible encoding table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

cmAccPortPcpDEEncInPriority 1.3.6.1.4.1.2544.1.12.4.1.21.1.2
This object is the input priority that is translated to a drop eligibility priority or a drop ineligibility priority.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmAccPortPcpDEEncDropIneligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.21.1.3
This object is the PCP value that has a priority value with implicit drop ineligibility encoded into it.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmAccPortPcpDEEncDropEligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.21.1.4
This object is the PCP value that has a priority value with implicit drop eligibility encoded into it.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmAccPortPcpDEDecTable 1.3.6.1.4.1.2544.1.12.4.1.22
Ethernet Access Port PCP drop eligibility decoding table. This is applied to a frame that is ingressing at a port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmAccPortPcpDEDecEntry

cmAccPortPcpDEDecEntry 1.3.6.1.4.1.2544.1.12.4.1.22.1
A conceptual row in the ethernetPBPcpDEDecPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmAccPortPcpDEDecEntry  

cmAccPortPcpDEDecIndex 1.3.6.1.4.1.2544.1.12.4.1.22.1.1
An integer index value used to uniquely identify a row in the PCP drop eligible decoding table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

cmAccPortPcpDEDecInPriority 1.3.6.1.4.1.2544.1.12.4.1.22.1.2
This object is the input priority that is decoded to get priority and the drop eligibility of a frame.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmAccPortPcpDEDecOutPriority 1.3.6.1.4.1.2544.1.12.4.1.22.1.3
This object is the priority value decoded from a incoming PCP value.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmAccPortPcpDEDecDropEligible 1.3.6.1.4.1.2544.1.12.4.1.22.1.4
This object is the drop eligibility decoded from a incoming PCP value.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmAccPortPcpDEPairTable 1.3.6.1.4.1.2544.1.12.4.1.23
Ethernet Access Port PCP drop eligibility priority pair table. The priority pair is encoded to same drop eligibility and drop ineligibility priority. Depending on the PCP DE Enc/Dec mode there can be upto 3 pairs in the table. There will one pair for 7P1D, two pairs for 6P2D and three pairs for 5P3D.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmAccPortPcpDEPairEntry

cmAccPortPcpDEPairEntry 1.3.6.1.4.1.2544.1.12.4.1.23.1
A conceptual row in the cmAccPortPcpDEPairEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmAccPortPcpDEPairEntry  

cmAccPortPcpDEPairIndex 1.3.6.1.4.1.2544.1.12.4.1.23.1.1
An integer index value used to uniquely identify a row in the PCP drop eligible priority pair table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..3  

cmAccPortPcpDEDropIneligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.23.1.2
This object is the drop ineligible priority.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmAccPortPcpDEDropEligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.23.1.3
This object is the drop eligible priority.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmNetPortPcpDEEncTable 1.3.6.1.4.1.2544.1.12.4.1.24
Ethernet Network Port PCP drop eligibility encoding table. This is applied to a frame that is egressing at the Network port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmNetPortPcpDEEncEntry

cmNetPortPcpDEEncEntry 1.3.6.1.4.1.2544.1.12.4.1.24.1
A conceptual row in the ethernetPBPcpDEEncPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmNetPortPcpDEEncEntry  

cmNetPortPcpDEEncIndex 1.3.6.1.4.1.2544.1.12.4.1.24.1.1
An integer index value used to uniquely identify a row in the PCP drop eligible encoding table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

cmNetPortPcpDEEncInPriority 1.3.6.1.4.1.2544.1.12.4.1.24.1.2
This object is the input priority that is translated to a drop eligibility priority or a drop ineligibility priority.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmNetPortPcpDEEncDropIneligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.24.1.3
This object is the PCP value that has a priority value with implicit drop ineligibility encoded into it.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmNetPortPcpDEEncDropEligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.24.1.4
This object is the PCP value that has a priority value with implicit drop eligibility encoded into it.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmNetPortPcpDEDecTable 1.3.6.1.4.1.2544.1.12.4.1.25
Ethernet Network Port PCP drop eligibility decoding table. This is applied to a frame that is ingressing at a port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmNetPortPcpDEDecEntry

cmNetPortPcpDEDecEntry 1.3.6.1.4.1.2544.1.12.4.1.25.1
A conceptual row in the ethernetPBPcpDEDecPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmNetPortPcpDEDecEntry  

cmNetPortPcpDEDecIndex 1.3.6.1.4.1.2544.1.12.4.1.25.1.1
An integer index value used to uniquely identify a row in the PCP drop eligible decoding table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

cmNetPortPcpDEDecInPriority 1.3.6.1.4.1.2544.1.12.4.1.25.1.2
This object is the input priority that is decoded to get priority and the drop eligibility of a frame.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmNetPortPcpDEDecOutPriority 1.3.6.1.4.1.2544.1.12.4.1.25.1.3
This object is the priority value decoded from a incoming PCP value.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmNetPortPcpDEDecDropEligible 1.3.6.1.4.1.2544.1.12.4.1.25.1.4
This object is the drop eligibility decoded from a incoming PCP value.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmNetPortPcpDEPairTable 1.3.6.1.4.1.2544.1.12.4.1.26
Ethernet Network Port PCP drop eligibility priority pair table. The priority pair is encoded to same drop eligibility and drop ineligibility priority. Depending on the PCP DE Enc/Dec mode there can be upto 3 pairs in the table. There will one pair for 7P1D, two pairs for 6P2D and three pairs for 5P3D.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmNetPortPcpDEPairEntry

cmNetPortPcpDEPairEntry 1.3.6.1.4.1.2544.1.12.4.1.26.1
A conceptual row in the cmNetPortPcpDEPairEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmNetPortPcpDEPairEntry  

cmNetPortPcpDEPairIndex 1.3.6.1.4.1.2544.1.12.4.1.26.1.1
An integer index value used to uniquely identify a row in the PCP drop eligible priority pair table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..3  

cmNetPortPcpDEDropIneligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.26.1.2
This object is the drop ineligible priority.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmNetPortPcpDEDropEligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.26.1.3
This object is the drop eligible priority.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmEthernetTrafficPortTable 1.3.6.1.4.1.2544.1.12.4.1.27
A list of entries corresponding to Ethernet Facilities for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetTrafficPortEntry

cmEthernetTrafficPortEntry 1.3.6.1.4.1.2544.1.12.4.1.27.1
A conceptual row in the cmEthernetTrafficPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetTrafficPortEntry  

cmEthernetTrafficPortIndex 1.3.6.1.4.1.2544.1.12.4.1.27.1.1
An integer index value used to uniquely identify this Ethernet Port within a card. Note that each Ethernet Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, cmEthernetTrafficPortIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

cmEthernetTrafficPortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.27.1.2
This object has the same value as ifIndex for Ethernet Port. An integer index value used to uniquely identify this Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

cmEthernetTrafficPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.27.1.3
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

cmEthernetTrafficPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.27.1.4
This object represents the Administrative State of the Ethernet Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmEthernetTrafficPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.27.1.5
This object represents the Operational State of the Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmEthernetTrafficPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.27.1.6
This object represents the Secondary State of the Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmEthernetTrafficPortMTU 1.3.6.1.4.1.2544.1.12.4.1.27.1.7
This object provides the MTU on the Ethernet Port. The object is made read-write for FSP150CC devices.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortMediaType 1.3.6.1.4.1.2544.1.12.4.1.27.1.8
This object represents the type of Ethernet Media on the Ethernet Port. The media type includes, copper (1) fiber (2) coppersfp (3) CM Aggregation Product doesn't support copper.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetMediaType  

cmEthernetTrafficPortConfigSpeed 1.3.6.1.4.1.2544.1.12.4.1.27.1.9
This object allows to configure the speed of the Ethernet Port.
Status: current Access: read-write
OBJECT-TYPE    
  EthernetPortSpeed  

cmEthernetTrafficPortNegotiatedSpeed 1.3.6.1.4.1.2544.1.12.4.1.27.1.10
This object provides the negotiated speed of the Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  EthernetPortSpeed  

cmEthernetTrafficPortMDIXType 1.3.6.1.4.1.2544.1.12.4.1.27.1.11
This object allows management of MDIX property on Ethernet Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetMDIXType  

cmEthernetTrafficPortMDIXStatus 1.3.6.1.4.1.2544.1.12.4.1.27.1.12
This object provides the current MDIX status of the Ethernet port.
Status: current Access: read-only
OBJECT-TYPE    
  CmEthernetMDIXType  

cmEthernetTrafficPortSfpVendorName 1.3.6.1.4.1.2544.1.12.4.1.27.1.13
This object provides the vendor name of the SFP. This is applicable when cmEthernetTrafficPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

cmEthernetTrafficPortSfpPartNumber 1.3.6.1.4.1.2544.1.12.4.1.27.1.14
This object provides the part number of the SFP. This is applicable when cmEthernetTrafficPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

cmEthernetTrafficPortSfpSerialNumber 1.3.6.1.4.1.2544.1.12.4.1.27.1.15
This object provides the serial number of the SFP. This is shown only when cmEthernetTrafficPortMediaType is fiber.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

cmEthernetTrafficPortSfpDateOfManufacture 1.3.6.1.4.1.2544.1.12.4.1.27.1.16
This object provides the date of manufacture of the SFP. This is applicable when cmEthernetTrafficPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

cmEthernetTrafficPortSfpConnectorValue 1.3.6.1.4.1.2544.1.12.4.1.27.1.17
This object provides the SFP connector value. This is applicable when cmEthernetTrafficPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  SfpConnectorValue  

cmEthernetTrafficPortSfpLinkLength 1.3.6.1.4.1.2544.1.12.4.1.27.1.18
This object provides the SFP Link Length. This is applicable only when cmEthernetTrafficPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortSfpLaserWaveLength 1.3.6.1.4.1.2544.1.12.4.1.27.1.19
This object provides the SFP Laser Wave Length in nano meters. This is applicable only when cmEthernetTrafficPortMediaType is fiber.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortSfpMediaType 1.3.6.1.4.1.2544.1.12.4.1.27.1.20
This object provides the SFP Media Type. This is applicable only when cmEthernetTrafficPortMediaType is fiber or coppersfp.
Status: current Access: read-only
OBJECT-TYPE    
  SfpMediaType  

cmEthernetTrafficPortLoopbackConfig 1.3.6.1.4.1.2544.1.12.4.1.27.1.21
This object allows to initiate loopbacks on on the Ethernet Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmLoopbackType  

cmEthernetTrafficPortLoopbackStatus 1.3.6.1.4.1.2544.1.12.4.1.27.1.22
This object provides status of the current loopback on the Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmLoopbackType  

cmEthernetTrafficPortLoopbackTime 1.3.6.1.4.1.2544.1.12.4.1.27.1.23
This object allows to specify time for timed-loopbacks on on the Ethernet Port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..300  

cmEthernetTrafficPortLoopbackSwapSADA 1.3.6.1.4.1.2544.1.12.4.1.27.1.24
This object allows to specify whether or not the loopbacked frame will have the Source Address and Destination Address swapped.
Status: current Access: read-write
OBJECT-TYPE    
  CmSwapSADAType  

cmEthernetTrafficPortOuterVlanLoopbackMask 1.3.6.1.4.1.2544.1.12.4.1.27.1.25
This object allows specification of the outer VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Outer VLAN 1 Loopback Enabled 2 Outer VLAN 2 Loopback Enabled 4 Outer VLAN 3 Loopback Enabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

cmEthernetTrafficPortOuterVlanLoopback1 1.3.6.1.4.1.2544.1.12.4.1.27.1.26
This object allows specification of the outer VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetTrafficPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetTrafficPortOuterVlanLoopback2 1.3.6.1.4.1.2544.1.12.4.1.27.1.27
This object allows specification of the outer VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetTrafficPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetTrafficPortOuterVlanLoopback3 1.3.6.1.4.1.2544.1.12.4.1.27.1.28
This object allows specification of the outer VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetTrafficPortOuterVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetTrafficPortLinkLossFwdEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.29
This object allows enabling/disabling link loss forwarding on the Ethernet Port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortLinkLossFwdSignalType 1.3.6.1.4.1.2544.1.12.4.1.27.1.30
This object allows definition of the link loss forwarding signalling type. This is applicable only if cmEthernetTrafficPortLinkLossFwdEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  CmLinkLossFwdSignalType  

cmEthernetTrafficPortLinkLossFwdTriggerTypes 1.3.6.1.4.1.2544.1.12.4.1.27.1.31
This object allows definition of the link loss forwarding trigger types. This is applicable only if cmEthernetTrafficPortLinkLossFwdEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  CmLinkLossFwdTriggerTypes  

cmEthernetTrafficPortLinkLossFwdDelay 1.3.6.1.4.1.2544.1.12.4.1.27.1.32
This object allows specification of the delay between detection of link loss and signalling of link loss forwarding. Time specified is in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortLinkLossFwdActive 1.3.6.1.4.1.2544.1.12.4.1.27.1.33
This object provides the link loss forwarding status indicating if link loss forwarding is currently being signaled via the port.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortLinkLossFwdPartnerEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.34
This object provides the indication of a link partners ability to support link loss forwarding via EFM, i.e. from received organization specific OAMPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortLinkLossFwdLocalLinkId 1.3.6.1.4.1.2544.1.12.4.1.27.1.35
This object allows configuration of the Local Link Id on Ethernet port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortLinkLossFwdRemoteLinkIds 1.3.6.1.4.1.2544.1.12.4.1.27.1.36
This object allows enabling/disabling Remote Link Ids on Ethernet port. the Ethernet port is able to distinguish the remote side client ports from the Remote Link Down PDUs coming from remote end. The cmEthernetTrafficPortLinkLossFwdLocalLinkId must be set before set cmEthernetTrafficPortLinkLossFwdRemoteLinkIds, By setting the Remote Link Ids seperated by the comma, e.g. 1,2,3,10,20..., up to 10 remote ID numbers can be added, number ranger is from 1 to 256(for EGX8.1, max value is 554). By setting nothing or '' to disable the Remote Link Ids.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..512)  

cmEthernetTrafficPortLinkLossFwdTxActionType 1.3.6.1.4.1.2544.1.12.4.1.27.1.37
This object allows to specify the Ethernet Port's behavior when link loss forwarding trigger events occur on the Port. This provides ability to configure per Ethernet port LLF behavior.
Status: current Access: read-write
OBJECT-TYPE    
  CmLinkLossFwdTxActionType  

cmEthernetTrafficPortLinkLossFwdRxRLDLinkIds 1.3.6.1.4.1.2544.1.12.4.1.27.1.38
This object provides the received Remote Link IDs in EFM RLD messages on the Ethernet Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..512)  

cmEthernetTrafficPortOamId 1.3.6.1.4.1.2544.1.12.4.1.27.1.39
OAM Id. This is unique EFM OAM sublayer port id.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortOamDiscoveryState 1.3.6.1.4.1.2544.1.12.4.1.27.1.40
Ethernet Port's OAM discovery state.
Status: current Access: read-only
OBJECT-TYPE    
  CmOamDiscoveryState  

cmEthernetTrafficPortOamLocalVarRtrvsEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.41
This object allows specification of whether the Ethernet Port supports sending variable response OAMPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortOamLocalLinkEventsEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.42
This object allows specification of whether the Ethernet Port supports interpreting Link Events.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortOamLocalOamLoopbacksSupported 1.3.6.1.4.1.2544.1.12.4.1.27.1.43
This object allows specification of whether the Ethernet Port is capable of OAM remote loopback mode.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortOamLocalUnidirSupportEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.44
This object allows specification of whether the Ethernet Port is capable of sending OAMPDUs when the receive path is non-operational.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortOamLocalMaxPDUSize 1.3.6.1.4.1.2544.1.12.4.1.27.1.45
This object represents the largest OAMPDU, in octets, supported by the Ethernet Port. This value is compared to the remote Maximum PDU Size and the smaller of the two is used.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortOamLocalMode 1.3.6.1.4.1.2544.1.12.4.1.27.1.46
This object allows to configure the OAM sublayer entity in either Active or Passive mode.
Status: current Access: read-write
OBJECT-TYPE    
  CmOamMode  

cmEthernetTrafficPortOamRemoteMacAddress 1.3.6.1.4.1.2544.1.12.4.1.27.1.47
This object allows retrieval of the Remote Mac Address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cmEthernetTrafficPortOamRemoteVarRtrvsEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.48
This object allows retrieval of whether the remote OAM entity supports sending variable response OAMPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortOamRemoteLinkEventsEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.49
This object allows retrieval of whether the remote OAM entity supports interpreting Link Events.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortOamRemoteOamLoopbacksSupported 1.3.6.1.4.1.2544.1.12.4.1.27.1.50
This object allows retrieval of whether the remote OAM entity supports OAM remote loopback mode.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortOamRemoteUnidirSupportEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.51
This object allows retrieval of whether the remote OAM entity is capable of sending OAMPDUs when the receive path is non-operational.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortOamRemoteMaxPDUSize 1.3.6.1.4.1.2544.1.12.4.1.27.1.52
This object allows retrieval of the remote OAM entity maximum OAMPDU size.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortOamRemoteMode 1.3.6.1.4.1.2544.1.12.4.1.27.1.53
This object allows to retrieve whether the remote OAM sublayer entity is either in Active or Passive mode.
Status: current Access: read-only
OBJECT-TYPE    
  CmOamMode  

cmEthernetTrafficPortOamEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.54
This object allows to manage the EFM OAM on Ethernet Traffic Port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortOamAdminState 1.3.6.1.4.1.2544.1.12.4.1.27.1.55
This object provides the EFM OAM Admin State.
Status: current Access: read-only
OBJECT-TYPE    
  CmOamAdminState  

cmEthernetTrafficPortSvcType 1.3.6.1.4.1.2544.1.12.4.1.27.1.56
This object allows specification of whether the Ethernet Port is port based or vlan based.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetTrafficSvcType  

cmEthernetTrafficPortRxPauseEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.57
This object defines the RxPause enable or disable of the port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortTxPauseEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.58
This object allows enabling/disabling transmit pause frames on Ethernet port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortAfpType 1.3.6.1.4.1.2544.1.12.4.1.27.1.59
This object allows specification of the Acceptable Frame Policy on Ethernet port. Users can specify whether the port supports only tagged frames, only untagged frames or both tagged and untagged frames.
Status: current Access: read-write
OBJECT-TYPE    
  CmAfpType  

cmEthernetTrafficPortShapingEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.60
This object allows to manage the Ethernet Port Shaping. When enabled, values in cmEthernetTrafficPortShapedSpeedLo and cmEthernetTrafficPortShapedSpeedHi are applicable.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortShapedSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.27.1.61
This object allows to specify the lower 32 bits of the Ethernet Port Shaped speed. This value is applicable when cmEthernetTrafficPortShapingEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmEthernetTrafficPortShapedSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.27.1.62
This object allows to specify the higher 32 bits of the Port Shaped speed. This value is applicable when cmEthernetTrafficPortShapingEnabled is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmEthernetTrafficPortQinQEtherType 1.3.6.1.4.1.2544.1.12.4.1.27.1.63
This object allows to specify the Q-in-Q Ether Type on the Port.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmEthernetTrafficPortTagFrameControl 1.3.6.1.4.1.2544.1.12.4.1.27.1.64
This object defines if c-tag/s-tag frame is allowed to pass through, available only when AFP is set to Tagged.
Status: current Access: read-write
OBJECT-TYPE    
  AfpTagControl  

cmEthernetTrafficPortEgressVlanTrunkingEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.65
This object allows to enable or disable the VLAN trunking on Ethernet port. Disabling VLAN trunking removes all VLAN tags before transmitting traffic out of the port. This object is only applicable for connection-oriented, evpl service type.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortIngressPushPVIDEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.66
This object allows to specify whether cmEthernetTrafficPortPortVlanId value will be PUSHed on untagged frames or not in the ingress direction. This object is only applicable for connection-oriented, evpl service type.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortEgressPopPVIDEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.67
This object allows to specify whether cmEthernetTrafficPortPortVlanId value will be POPed in the egress direction. This object is only applicable for connection-oriented, evpl service type.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortEgressPopPriorityVidEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.68
This object defines the egress PopPriorityVid enable or disable of the port. If it is enabled, the outgoing packets with VID=Priority VLAN ID will be swapped back to VID=0.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortPortVlanId 1.3.6.1.4.1.2544.1.12.4.1.27.1.69
This object allows to specify the Ethernet Port VLAN Id to PUSH on untagged frames in the to Network direction. This object is only applicable for connection-oriented, evpl service type, when cmEthernetTrafficPortIngressPushPVIDEnabled is set to true.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

cmEthernetTrafficPortPortVlanPriority 1.3.6.1.4.1.2544.1.12.4.1.27.1.70
This object allows to specify the Ethernet Port VLAN Priority for the PUSHed VLAN tag (specified by cmEthernetTrafficPortPortVlanId) on untagged frames in the ingress direction. This object is only applicable for connection-oriented, evpl service type, when cmEthernetTrafficPortIngressPushPVIDEnabled is set to true.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmEthernetTrafficPortPriorityVlanId 1.3.6.1.4.1.2544.1.12.4.1.27.1.71
This object allows to specify the Ethernet Priority VLAN Id to replace the null-tagged or priority tagged frames in the to ingress direction. This object is only applicable for connection-oriented, evpl service type.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

cmEthernetTrafficPortIngressPrioMapMode 1.3.6.1.4.1.2544.1.12.4.1.27.1.72
This object allows to specify the Ethernet Port Priority Mapping Mode used for classification of frames. This object is only applicable for connection-oriented, evpl service type.
Status: current Access: read-write
OBJECT-TYPE    
  PriorityMapMode  

cmEthernetTrafficPortIngressCOSPriority 1.3.6.1.4.1.2544.1.12.4.1.27.1.73
This object is used to specify whether the EthernetTrafficPort uses the inner-tag or the outer-tag in determining the COS (Class of Service).
Status: current Access: read-create
OBJECT-TYPE    
  VlanTagType  

cmEthernetTrafficPortSyncEEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.74
This object allows to specify whether the Ethernet Port can be enabled/disabled for Synchronous Ethernet. This object is only applicable for Synchronous Ethernet capable ports. When enabled, on receive side -port can extract the frequency of its input signal and pass the recovered clock to the system clock -port processes the ESMC(Ethernet Synchronization Messaging Channel) and extracts the QL (when also QL enabled) -port is eligible to be selected as a system clock reference When enabled, on transmit side -port's transmit clock is locked to the system clock -port generates an ESMC to generate a QL (when also QL enabled) When disabled, on receive side, -port does not pass the recovered clock to the system clock -port does not process the ESMC (if present) -port is not eligible to be selected as a system clock reference When disabled, on transmit side -port's output frequency may be synchronized to the system clock -port does not generate an ESMC.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortQLModeEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.75
This object allows to specify whether the Ethernet Port can be enabled/disabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetTrafficPortQLModeEnabled is set to true. When enabled, on receive side -port shall PEER the SSM (Sync Status Messages) slow protocol PDUs and take appropriate action When enabled, on transmit side -port shall periodically (once a second) transmit QL TLV information PDUs When disabled, on receive side, -port shall terminate and discard any SSM slow protocol PDUs When disabled, on transmit side -port shall not transmit any SSM slow protocol PDUs.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortExpectedQL 1.3.6.1.4.1.2544.1.12.4.1.27.1.76
This object allows to specify the expected QL when the Ethernet Port is enabled for QL Mode. This object is only applicable for Synchronous Ethernet capable ports, when cmEthernetTrafficPortQLModeEnabled is set to true. This object allows the user to set a minimum expected received Quality Level on the port. The valid values depend upon the SYNC entity Network Clock Type. A value of None represents that a minimum Quality Level is not expected. The default value shall be None.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetTrafficPortAssumedQL 1.3.6.1.4.1.2544.1.12.4.1.27.1.77
This object allows to specify the assumed QL on the Ethernet Port. This object is only applicable for Synchronous Ethernet capable ports. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port TransmitQL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetTrafficPortReceivedQL 1.3.6.1.4.1.2544.1.12.4.1.27.1.78
This object provides the Received QL value for the Ethernet port. If the Ethernet port TransmitQL Mode is disabled, then the received QL value is not applicable.This object is only applicable for Synchronous Ethernet capable ports.
Status: current Access: read-only
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetTrafficPortTransmitQL 1.3.6.1.4.1.2544.1.12.4.1.27.1.79
This object provides the Transmitted QL value for the Ethernet port. If the Ethernet port TransmitQL Mode is disabled, then the received QL value is not applicable. This object is only applicable for Synchronous Ethernet capable ports.
Status: current Access: read-only
OBJECT-TYPE    
  SSMQualityLevel  

cmEthernetTrafficPortPhyType 1.3.6.1.4.1.2544.1.12.4.1.27.1.80
This object is valid only to XGE card. And the value should be LAN or WAN when it is XGE card.
Status: current Access: read-write
OBJECT-TYPE    
  XgePhyType  

cmEthernetTrafficPortSfpLaserWaveLengthPicometer 1.3.6.1.4.1.2544.1.12.4.1.27.1.81
This object provide laser wavelength pico value. For example, laser wavelength is 1510.01, then cmEthernetTrafficPortSfpLaserWaveLength=1510 and cmTrafficPortSfpLaserWaveLengthPicometer=10.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cmEthernetTrafficPortRowStatus 1.3.6.1.4.1.2544.1.12.4.1.27.1.82
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmEthernetTrafficPortRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with neRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmEthernetTrafficPortRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmEthernetTrafficPortSSMRemoteMacAddress 1.3.6.1.4.1.2544.1.12.4.1.27.1.83
This object allows retrieval of the Remote Mac Address, when the port is peering using SSM.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cmEthernetTrafficPortInnerVlanLoopbackMask 1.3.6.1.4.1.2544.1.12.4.1.27.1.84
This object allows specification of the inner VLANs to be looped back when port is in vlan(terminal/facility) loopback configuration. Only 3 VLANs can be specified for vlan loopback. The various bit positions are: 1 Inner VLAN 1 Loopback Enabled 2 Inner VLAN 2 Loopback Enabled 4 Inner VLAN 3 Loopback Enabled
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

cmEthernetTrafficPortInnerVlanLoopback1 1.3.6.1.4.1.2544.1.12.4.1.27.1.85
This object allows specification of the inner VLAN 1 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetTrafficPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetTrafficPortInnerVlanLoopback2 1.3.6.1.4.1.2544.1.12.4.1.27.1.86
This object allows specification of the inner VLAN 2 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetTrafficPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetTrafficPortInnerVlanLoopback3 1.3.6.1.4.1.2544.1.12.4.1.27.1.87
This object allows specification of the inner VLAN 3 to be looped back when port is in vlan(terminal/facility) loopback configuration. This is valid only if the corresponding bit in cmEthernetTrafficPortInnerVlanLoopbackMask is set. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..6)  

cmEthernetTrafficPortLaserWDMChannel 1.3.6.1.4.1.2544.1.12.4.1.27.1.88
Channel number of WDM tunable XFP setting.
Status: current Access: read-write
OBJECT-TYPE    
  SfpChannelIdentifier  

cmEthernetTrafficPortLaserIsTunable 1.3.6.1.4.1.2544.1.12.4.1.27.1.89
This object means this module whether tunnable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortLaserFrequency 1.3.6.1.4.1.2544.1.12.4.1.27.1.90
This object describes this module's frequency, and the step is 1GHZ.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cmEthernetTrafficPortDeiEnable 1.3.6.1.4.1.2544.1.12.4.1.27.1.91
This object describes whether use DEI bit in S-tag to recognize Drop Eligibility Parameter for ingress S-tag packets or Set DEI bit for egress S-tag Packets. This object is still supported by OSA8.1.1
Status: deprecated Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortPcpDEEncType 1.3.6.1.4.1.2544.1.12.4.1.27.1.92
This object describes the PCP encoding mode for egress packets and the PCP decoding mode for ingress packets on this port.
Status: current Access: read-write
OBJECT-TYPE    
  PcpDEEncType  

cmEthernetTrafficPortPcpDEPairsAction 1.3.6.1.4.1.2544.1.12.4.1.27.1.93
This object describes this port pcp de pairs action.
Status: current Access: read-write
OBJECT-TYPE    
  PcpDEPairsAction  

cmEthernetTrafficPortInitiateDiag 1.3.6.1.4.1.2544.1.12.4.1.27.1.94
This object allows to initiate Etherjack diagnosis on the Ethernet Traffic Port.
Status: current Access: read-write
OBJECT-TYPE    
  CmEthernetDiagAction  

cmEthernetTrafficPortDiagnosePair1Cond 1.3.6.1.4.1.2544.1.12.4.1.27.1.95
This object provides diagnosis results for the cable Pair 1 on Ethernet Traffic Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetTrafficPortDiagnosePair2Cond 1.3.6.1.4.1.2544.1.12.4.1.27.1.96
This object provides diagnosis results for the cable Pair 2 on Ethernet Traffic Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetTrafficPortDiagnosePair3Cond 1.3.6.1.4.1.2544.1.12.4.1.27.1.97
This object provides diagnosis results for the cable Pair 3 on Ethernet Traffic Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetTrafficPortDiagnosePair4Cond 1.3.6.1.4.1.2544.1.12.4.1.27.1.98
This object provides diagnosis results for the cable Pair 4 on Ethernet Traffic Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagCableCondType  

cmEthernetTrafficPortDiagnoseAutoNegCond 1.3.6.1.4.1.2544.1.12.4.1.27.1.99
This object provides auto negotiation results of the diagnosis test on Ethernet Traffic Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagAutoNegCondType  

cmEthernetTrafficPortDiagnoseLpbkCond 1.3.6.1.4.1.2544.1.12.4.1.27.1.100
This object provides port loopback results of the diagnosis test on Ethernet Traffic Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagLpbkCondType  

cmEthernetTrafficPortDiagnoseEfmLpbkCond 1.3.6.1.4.1.2544.1.12.4.1.27.1.101
This object provides remote EFM loopback results of the diagnosis test on Ethernet Traffic Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagEfmOamLpbkCondType  

cmEthernetTrafficPortDiagnoseResult 1.3.6.1.4.1.2544.1.12.4.1.27.1.102
This object provides results of the diagnosis test in string form on Ethernet Traffic Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

cmEthernetTrafficPortDiagnoseTestStatus 1.3.6.1.4.1.2544.1.12.4.1.27.1.103
This object provides the current status of the diagnosis test on Ethernet Traffic Port.
Status: current Access: read-only
OBJECT-TYPE    
  CmDiagTestStatus  

cmEthernetTrafficPortDiagnoseTestTime 1.3.6.1.4.1.2544.1.12.4.1.27.1.104
This object provides the time when diagnosis test was last executed.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

cmEthernetTrafficPortAutoDiagEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.105
This object allows to enable or disable the automatic Cable Diagnostic tests when the cable is removed from the port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortDeleteEntitiesAction 1.3.6.1.4.1.2544.1.12.4.1.27.1.106
This object allows to delete esa entities relate this port and Cfm entities relate this port.
Status: current Access: read-write
OBJECT-TYPE    
  TrafficPortDeleteEntitiesAction  

cmEthernetTrafficPortMaxMpFpNum 1.3.6.1.4.1.2544.1.12.4.1.27.1.107
This object allows to set the mpflow max fp number, and now only the ports on ethernet10x1GCard, ethernet1x10GCard, ethernet1x10GHighPerCard, ethernet10x1GHighPerCard support this attribute. for others, cann't be set and will return 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortJdsuLoopbackEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.108
This object allows to enable or disable jdsu loopback on this port. Note: This object is deprecated.
Status: deprecated Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortJdsuLoopbackVlanId 1.3.6.1.4.1.2544.1.12.4.1.27.1.109
This object allows to set the jdsu loopback vlan. if status is jdsu-terminal-port-tailend(19) or jdsu-facility-port-tailend(21), then VID is 0 means not applicable. Note: This object is deprecated.
Status: deprecated Access: read-only
OBJECT-TYPE    
  VlanId  

cmEthernetTrafficPortIngressPopPriorityVidEnabled 1.3.6.1.4.1.2544.1.12.4.1.27.1.110
This object defines the Ingress PopPriorityVid enable or disable of the port. If it is enabled, then incoming priority tagged packet's VID is swapped to Priority VLAN ID.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortRxDeiAction 1.3.6.1.4.1.2544.1.12.4.1.27.1.111
This object allows to specify the Receive DEI Action.
Status: current Access: read-write
OBJECT-TYPE    
  RxDeiAction  

cmEthernetTrafficPortTxDeiAction 1.3.6.1.4.1.2544.1.12.4.1.27.1.112
This object allows to specify the Transmit DEI Action.
Status: current Access: read-write
OBJECT-TYPE    
  TxDeiAction  

cmEthernetTrafficPortRxDeiOuterTagType 1.3.6.1.4.1.2544.1.12.4.1.27.1.113
This object allows to specify the Receive DEI Outer Tag Type.
Status: current Access: read-write
OBJECT-TYPE    
  DeiOuterTagType  

cmEthernetTrafficPortTxDeiOuterTagType 1.3.6.1.4.1.2544.1.12.4.1.27.1.114
This object allows to specify the Transmit DEI Outer Tag Type.
Status: current Access: read-write
OBJECT-TYPE    
  DeiOuterTagType  

cmElineFlowTable 1.3.6.1.4.1.2544.1.12.4.1.28
A list of entries corresponding to Flows for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmElineFlowEntry

cmElineFlowEntry 1.3.6.1.4.1.2544.1.12.4.1.28.1
A conceptual row in the cmElineFlowTable. These entries represent an Flow.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmElineFlowEntry  

cmElineFlowIndex 1.3.6.1.4.1.2544.1.12.4.1.28.1.1
The integer index value corresponding to an Flow.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

cmElineFlowCircuitName 1.3.6.1.4.1.2544.1.12.4.1.28.1.2
This object allows SNMP management entities to provide a circuit identifier with the Flow.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..256)  

cmElineFlowAdminState 1.3.6.1.4.1.2544.1.12.4.1.28.1.3
This object represents the Administrative State of the Flow.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmElineFlowOperationalState 1.3.6.1.4.1.2544.1.12.4.1.28.1.4
This object represents the Operational State of the Flow.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmElineFlowSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.28.1.5
This object represents the Secondary State of the Flow.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmElineFlowFP1 1.3.6.1.4.1.2544.1.12.4.1.28.1.6
This object allows SNMP management entities to provide a flowpoint with the Flow.
Status: current Access: read-create
OBJECT-TYPE    
  VariablePointer  

cmElineFlowFP2 1.3.6.1.4.1.2544.1.12.4.1.28.1.7
This object allows SNMP management entities to provide another flowpoint with the Flow.
Status: current Access: read-create
OBJECT-TYPE    
  VariablePointer  

cmElineFlowStorageType 1.3.6.1.4.1.2544.1.12.4.1.28.1.8
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmElineFlowRowStatus 1.3.6.1.4.1.2544.1.12.4.1.28.1.9
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmElineFlowRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmElineFlowRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmElineFlowRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmFlowPointTable 1.3.6.1.4.1.2544.1.12.4.1.29
A list of entries corresponding to FlowPoint for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmFlowPointEntry

cmFlowPointEntry 1.3.6.1.4.1.2544.1.12.4.1.29.1
A conceptual row in the cmFlowPointTable. These entries represent an FlowPoint. If the flowpoint attached to a lag, the slotIndex should be 255(255 is used to identify the flowpoint belongs to lag), and the cmEthernetTrafficPortIndex should be the f3LagIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmFlowPointEntry  

cmFlowPointIndex 1.3.6.1.4.1.2544.1.12.4.1.29.1.1
The integer index value corresponding to an FlowPoint.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

cmFlowPointCircuitName 1.3.6.1.4.1.2544.1.12.4.1.29.1.2
This object allows SNMP management entities to provide a circuit identifier with the FlowPoint.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..256)  

cmFlowPointAdminState 1.3.6.1.4.1.2544.1.12.4.1.29.1.3
This object represents the Administrative State of the FlowPoint.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmFlowPointOperationalState 1.3.6.1.4.1.2544.1.12.4.1.29.1.4
This object represents the Operational State of the FlowPoint.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmFlowPointSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.29.1.5
This object represents the Secondary State of the FlowPoint.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmFlowPointAssociatedFlowId 1.3.6.1.4.1.2544.1.12.4.1.29.1.6
This object provides the association of an Flow with an FlowPoint.
Status: current Access: read-only
OBJECT-TYPE    
  VariablePointer  

cmFlowPointIngressMultiCOS 1.3.6.1.4.1.2544.1.12.4.1.29.1.7
This object allows specification of ingress multiple COS (Class of Service) FlowPoint.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowPointIngressCOS 1.3.6.1.4.1.2544.1.12.4.1.29.1.8
This object allows specification of ingress COS (Class of Service) FlowPoint.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cmFlowPointIngressVlanMemberList 1.3.6.1.4.1.2544.1.12.4.1.29.1.9
It allows specification of VLAN members of the FlowPoint. VLAN members are comma separated, of the form X-Y where X is the VLAN Id and Y is the VLAN Priority. VLAN members can be of the form X-* or X (vlan X with all priorities), *-Y (all vlans with priority Y), and X1:X2 (range of vlans from X1 to X2, all priorities). Members with specific VLAN Id and specific VLAN Priority are not supported. Once the flowpoint is created, this attribute can only be updated using cmFlowPointVlanMemberAction and cmFlowPointVlanMemberActionVlan objects.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..512)  

cmFlowPointVlanMemberAction 1.3.6.1.4.1.2544.1.12.4.1.29.1.10
This object allows to add or remove the VLAN members specified by cmFlowPointVlanMemberActionVlan object. SNMP manager must first configure the VLAN member to be added/removed in the object cmFlowPointVlanMemberActionVlan and then should specify cmFlowPointVlanMemberAction on whether to add/remove the specified VLAN member.
Status: current Access: read-write
OBJECT-TYPE    
  FlowVlanActionType  

cmFlowPointVlanMemberActionVlan 1.3.6.1.4.1.2544.1.12.4.1.29.1.11
This object allows adding/removing VLAN members to a flowpoint. VLAN member is of the form X-Y where X is the VLAN Id and Y is the VLAN Priority. VLAN members can be of the form X-* (vlan X with all priorities), *-Y (all vlans with priority Y), and X1:X2 (range of vlans from X1 to X2, all priorities). Members with specific VLAN Id and specific VLAN Priority are not supported. In order to add/remove VLAN member to a flow, user must specify this object with appropriate VLAN and then invoke cmFlowPointVlanMemberAction.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..16)  

cmFlowPointIngressUntaggedFrameEnabled 1.3.6.1.4.1.2544.1.12.4.1.29.1.12
This object allows to specify whether or not the flowpoint supports untagged frame.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowPointCTagControl 1.3.6.1.4.1.2544.1.12.4.1.29.1.13
This object allows specification of the tag management operation on the C-TAG. Supported types are 'push', 'pushvid', 'swaptag', 'swapvid' and 'none'. If the type is 'push', the VLAN Id (cmFlowPointCTagVlanId) and priority (cmFlowPointCTagVlanPriority) are pushed onto the frame; if the type is 'pushvid', only the VLAN Id (12 bits) is pushed, the Priority is copied from incoming tag's priority; if the type is 'swaptag', both VLAN Id and Priority (15 bits) are swapped with the specified cmFlowPointCTagVlanId and cmFlowPointCTagVlanPriority; if the type is 'swapvid', only the VLAN Id (12 bits) are swapped with the specified cmFlowPointCTagVlanId; if the type is 'none', no C-TAG management is performed.
Status: current Access: read-create
OBJECT-TYPE    
  FlowTagControl  

cmFlowPointCTagVlanId 1.3.6.1.4.1.2544.1.12.4.1.29.1.14
This object allows specification of the VLAN Id to be pushed or swapped, based on the value of cmFlowPointIngressCTagControl. It is applicable for 'push', 'swaptag', 'swapvid' and 'pushvid' control types.
Status: current Access: read-create
OBJECT-TYPE    
  VlanId  

cmFlowPointCTagVlanPriority 1.3.6.1.4.1.2544.1.12.4.1.29.1.15
This object allows specification of the VLAN Priority to be pushed or swapped, based on the value of cmFlowPointIngressCTagControl. It is applicable for 'push' and 'swaptag' control types.
Status: current Access: read-create
OBJECT-TYPE    
  VlanPriority  

cmFlowPointSTagControl 1.3.6.1.4.1.2544.1.12.4.1.29.1.16
This object allows specification of the tag management operation on the S-TAG. Supported types are 'push', 'pushvid', 'swaptag', 'swapvid' and 'none'. If the type is 'push', the VLAN Id (cmFlowPointSTagVlanId) and priority (cmFlowPointSTagVlanPriority) are pushed onto the frame; if the type is 'pushvid', only the VLAN Id (12 bits) is pushed, the Priority is copied from incoming tag's priority; if the type is 'swaptag', both VLAN Id and Priority (15 bits) are swapped with the specified cmFlowPointSTagVlanId and cmFlowPointSTagVlanPriority; if the type is 'swapvid', only the VLAN Id (12 bits) are swapped with the specified cmFlowPointSTagVlanId; if the type is 'none', no S-TAG management is performed.
Status: current Access: read-create
OBJECT-TYPE    
  FlowTagControl  

cmFlowPointSTagVlanId 1.3.6.1.4.1.2544.1.12.4.1.29.1.17
This object allows specification of the VLAN Id to be pushed or swapped, based on the value of cmFlowPointIngressSTagControl. It is applicable for 'push', 'swaptag', 'swapvid' and 'pushvid' control types.
Status: current Access: read-create
OBJECT-TYPE    
  VlanId  

cmFlowPointSTagVlanPriority 1.3.6.1.4.1.2544.1.12.4.1.29.1.18
This object allows specification of the VLAN Priority to be pushed or swapped, based on the value of cmFlowPointIngressSTagControl. It is applicable for 'push' and 'swaptag' control types.
Status: current Access: read-create
OBJECT-TYPE    
  VlanPriority  

cmFlowPointEgressOuterTagPrioMapEnabled 1.3.6.1.4.1.2544.1.12.4.1.29.1.19
This object defines whether to use the Egress Prio Mapping to swap the priority of outer tag. When Enabled,it indicates that the operation specified in the EgressPrioMapTable would be applied to Flow for specified COS. When Disabled,the EgressPrioMapTable operations are ignored for specified Flow COS.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowPointColorMarkingSupported 1.3.6.1.4.1.2544.1.12.4.1.29.1.20
This object defines the egress color marking. If set to Enabled, the DEI bit of S-tag pushed will be remarked according the meter result. If set to Disabled, the DEI bit is forced to 0.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmFlowPointAssociatedAclProfile 1.3.6.1.4.1.2544.1.12.4.1.29.1.21
This object provides the association of an Flow with an ACL profile.
Status: current Access: read-create
OBJECT-TYPE    
  VariablePointer  

cmFlowPointSESFramesLossThresholdRatio 1.3.6.1.4.1.2544.1.12.4.1.29.1.22
This object is used to specify the frame-loss ratio per flow that starts counting Severely Errored Seconds (SES) on the flowpoint. This functionality is applicable if the flowpoint is monitored using the Y.1731 ESA functionality.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

cmFlowPointStorageType 1.3.6.1.4.1.2544.1.12.4.1.29.1.23
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmFlowPointRowStatus 1.3.6.1.4.1.2544.1.12.4.1.29.1.24
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmFlowPointRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmFlowPointRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmFlowPointRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmFlowPointDefaultMemberEnabled 1.3.6.1.4.1.2544.1.12.4.1.29.1.25
defaultMemberEnabled with enabled means that on this FP, the membership is all the tag packets without match any other membership associated to the port. Untagged means untagged flow. Default only care tagged flow.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmFlowPointMcastRateLimitEnabled 1.3.6.1.4.1.2544.1.12.4.1.29.1.26
Whether multicast packets need be limited per FP.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmFlowPointMcastRateLimitSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.29.1.27
The rate limiting for multicast packets per FP When cmFlowPointMcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowPointMcastRateLimitSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.29.1.28
The rate limiting for multicast packets per FP When cmFlowPointMcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowPointBcastRateLimitEnabled 1.3.6.1.4.1.2544.1.12.4.1.29.1.29
Whether broadcast packets need be limited per FP.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmFlowPointBcastRateLimitSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.29.1.30
The rate limiting for broadcast packets per FP When cmFlowPointBcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowPointBcastRateLimitSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.29.1.31
The rate limiting for broadcast packets per FP When cmFlowPointBcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowPointSplitHorizonGroupOID 1.3.6.1.4.1.2544.1.12.4.1.29.1.32
Specifies the Split-Horizon Group EID. If there is no SHG, the value is none.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmFlowPointLoopAvoidance 1.3.6.1.4.1.2544.1.12.4.1.29.1.33
EID of this associated Loop Avoidance protocol entity. A value of NONE indicates there is no loop avoidance protocol. Currently ERP EID is filled when ELAN service is created.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmFlowPointHierarchicalCosEnabled 1.3.6.1.4.1.2544.1.12.4.1.29.1.34
Enable or Disable Hierarchical COS shaping (flow shaping).
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmFlowPointWfqQid 1.3.6.1.4.1.2544.1.12.4.1.29.1.35
This attribute description the WFQ Qid.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmFlowPointWfqOutPriority 1.3.6.1.4.1.2544.1.12.4.1.29.1.36
This attribute description the WFQ out priority.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmFlowPointMaximumBWLo 1.3.6.1.4.1.2544.1.12.4.1.29.1.37
This attribute description the flow point maximum bandwidth. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowPointMaximumBWHi 1.3.6.1.4.1.2544.1.12.4.1.29.1.38
This attribute description the flow point maximum bandwidth. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowPointGuaranteedBWLo 1.3.6.1.4.1.2544.1.12.4.1.29.1.39
This attribute description the flow point guaranteed bandwidth. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowPointGuaranteedBWHi 1.3.6.1.4.1.2544.1.12.4.1.29.1.40
This attribute description the flow point guaranteed bandwidth. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowPointRefPrioMapProfile 1.3.6.1.4.1.2544.1.12.4.1.29.1.41
This object allows to set priority map profile.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmFlowPointMcastAndBcastRateLimitEnabled 1.3.6.1.4.1.2544.1.12.4.1.29.1.42
Whether multicast packets and broadcast packets need be limited per FP.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmFlowPointMcastAndBcastRateLimitSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.29.1.43
The rate limiting for multicast packets and broadcast packets per FP When cmFlowPointMcastAndBcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmFlowPointMcastAndBcastRateLimitSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.29.1.44
The rate limiting for multicast packets and broadcast packets per FP When cmFlowPointMcastAndBcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmOAMFlowPointTable 1.3.6.1.4.1.2544.1.12.4.1.30
A list of entries corresponding to OAMFlowPoint for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmOAMFlowPointEntry

cmOAMFlowPointEntry 1.3.6.1.4.1.2544.1.12.4.1.30.1
A conceptual row in the cmOAMFlowPointTable. These entries represent an FlowPoint. If the oam flowpoint attached to a lag, the slotIndex should be 255(255 is used to identify the oam flowpoint belongs to lag), and the cmEthernetTrafficPortIndex should be the f3LagIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmOAMFlowPointEntry  

cmOAMFlowPointIndex 1.3.6.1.4.1.2544.1.12.4.1.30.1.1
The integer index value corresponding to an OAMFlowPoint.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

cmOAMFlowPointCircuitName 1.3.6.1.4.1.2544.1.12.4.1.30.1.2
This object allows SNMP management entities to provide a circuit identifier with the OAMFlowPoint.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

cmOAMFlowPointAdminState 1.3.6.1.4.1.2544.1.12.4.1.30.1.3
This object represents the Administrative State of the OAMFlowPoint.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmOAMFlowPointOperationalState 1.3.6.1.4.1.2544.1.12.4.1.30.1.4
This object represents the Operational State of the OAMFlowPoint.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmOAMFlowPointSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.30.1.5
This object represents the Secondary State of the OAMFlowPoint.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmOAMFlowPointIngressVlanMemberList 1.3.6.1.4.1.2544.1.12.4.1.30.1.6
It allows specification of VLAN members of the OAMFlowPoint. VLAN members are comma separated, of the form X-Y where X is the VLAN Id and Y is the VLAN Priority. VLAN members can be of the form X-* or X (vlan X with all priorities), *-Y (all vlans with priority Y), and X1:X2 (range of vlans from X1 to X2, all priorities). Members with specific VLAN Id and specific VLAN Priority are not supported. Once the flowpoint is created, this attribute can only be updated using cmOAMFlowPointVlanMemberAction and cmOAMFlowPointVlanMemberActionVlan objects.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..512)  

cmOAMFlowPointVlanMemberAction 1.3.6.1.4.1.2544.1.12.4.1.30.1.7
This object allows to add or remove the VLAN members specified by cmOAMFlowPointVlanMemberActionVlan object. SNMP manager must first configure the VLAN member to be added/removed in the object cmOAMFlowPointVlanMemberActionVlan and then should specify cmOAMFlowPointVlanMemberAction on whether to add/remove the specified VLAN member.
Status: current Access: read-write
OBJECT-TYPE    
  FlowVlanActionType  

cmOAMFlowPointVlanMemberActionVlan 1.3.6.1.4.1.2544.1.12.4.1.30.1.8
This object allows adding/removing VLAN members to a oam flowpoint. VLAN member is of the form X-Y where X is the VLAN Id and Y is the VLAN Priority. VLAN members can be of the form X-* (vlan X with all priorities), *-Y (all vlans with priority Y), and X1:X2 (range of vlans from X1 to X2, all priorities). Members with specific VLAN Id and specific VLAN Priority are not supported. In order to add/remove VLAN member to a flow, user must specify this object with appropriate VLAN and then invoke cmOAMFlowPointVlanMemberAction.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..16)  

cmOAMFlowPointIngressUntaggedFrameSupported 1.3.6.1.4.1.2544.1.12.4.1.30.1.9
This object allows to specify whether or not the OAMFlowPoint supports untagged frame.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmOAMFlowPointSESFramesLossThresholdRatio 1.3.6.1.4.1.2544.1.12.4.1.30.1.10
This object is used to specify the frame-loss ratio per flow that starts counting Severely Errored Seconds (SES) on the oam flowpoint. This functionality is applicable if the oam flowpoint is monitored using the Y.1731 ESA functionality.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..100  

cmOAMFlowPointStorageType 1.3.6.1.4.1.2544.1.12.4.1.30.1.11
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmOAMFlowPointRowStatus 1.3.6.1.4.1.2544.1.12.4.1.30.1.12
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmOAMFlowPointRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmOAMFlowPointRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmOAMFlowPointRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmIngressPrioMapTable 1.3.6.1.4.1.2544.1.12.4.1.31
A list of entries corresponding to Ingress Priority Mapping for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmIngressPrioMapEntry

cmIngressPrioMapEntry 1.3.6.1.4.1.2544.1.12.4.1.31.1
A conceptual row in the cmIngressPrioMapTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmIngressPrioMapEntry  

cmIngressPrioMapIndex 1.3.6.1.4.1.2544.1.12.4.1.31.1.1
The integer index value corresponding to a priority value based on the cmEthernetTrafficPortPrioMapMode. In case of TOS and 8021P, valid indices are 1 to 8, in case of DSCP, valid indices are 1 to 64.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..64  

cmIngressPrioMapInPriority 1.3.6.1.4.1.2544.1.12.4.1.31.1.2
The integer index value corresponding to a priority value based on the cmEthernetTrafficPortIngressPrioMapMode. In case of TOS and 8021P, valid indices are 0 to 7, in case of DSCP, valid indices are 0 to 63.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..63  

cmIngressPrioMapCOS 1.3.6.1.4.1.2544.1.12.4.1.31.1.3
This allows specification of the COS Priority, i.e. this helps in determining the appropriate COS Policer for the Flow.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmEgressPrioMapTable 1.3.6.1.4.1.2544.1.12.4.1.32
A list of entries corresponding to Egress Priority Mapping for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEgressPrioMapEntry

cmEgressPrioMapEntry 1.3.6.1.4.1.2544.1.12.4.1.32.1
A conceptual row in the cmEgressPrioMapTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEgressPrioMapEntry  

cmEgressCOSIndex 1.3.6.1.4.1.2544.1.12.4.1.32.1.1
The integer index used to uniquely identify this Egress Priority Map Entry
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

cmEgressCOS 1.3.6.1.4.1.2544.1.12.4.1.32.1.2
This allows specification of the COS Priority, i.e. this helps in determining the appropriate COS Policer for the Flow.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmEgressOuterTagCtrl 1.3.6.1.4.1.2544.1.12.4.1.32.1.3
This object defines the behavior of the Priority portion of the frame transmit out. If NONE is selected, the outgoing priority bits are left unchanged. If SWAP is selected, the priority bits are changed by the value specified in the Outer-Tag Priority parameter.
Status: current Access: read-write
OBJECT-TYPE    
  PrioMapControlType  

cmEgressOuterTagPriority 1.3.6.1.4.1.2544.1.12.4.1.32.1.4
This object defines the new priority bits to be used, it is available only if Outer-Tag PRIOCTL is set to SWAP.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmPortCpdProfileTable 1.3.6.1.4.1.2544.1.12.4.1.33
A list of entries corresponding to System Control Protocol Disposition V3 profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmPortCpdProfileEntry

cmPortCpdProfileEntry 1.3.6.1.4.1.2544.1.12.4.1.33.1
A conceptual row in the cmPortCpdProfileTable. These entries represent a Control Protocol Disposition of a port filtering criteria of the System.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmPortCpdProfileEntry  

cmPortCpdProfileIndex 1.3.6.1.4.1.2544.1.12.4.1.33.1.1
Unique Index value to access the CPD profile row.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

cmPortCpdProfileName 1.3.6.1.4.1.2544.1.12.4.1.33.1.2
This object describes the alias of the cpd V3 profile entry.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

cmPortCpdProfileCiscoGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.3
Deprecated - each Cisco protocol has its own disposition. Control Protocol Disposition for Cisco Group. This includes ISL, PAGP, UDLD, CDP, VTP, DTP, PSVTP+, UplinkFast, VLAN Bridge, L2PT. Note that a specific protocol filter overrides the group setting.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileIslDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.4
Control Protocol Disposition for ISL (Inter Switch Link). MAC Address (01:00:0C:00:00:00).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfilePagpDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.5
Control Protocol Disposition for PAGP (Port Aggregation Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x104).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileUdldDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.6
Control Protocol Disposition for UDLD (Unidirectional Link Detection). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x111).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileCdpDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.7
Control Protocol Disposition for CDP (Cisco Discovery Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2000).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileVtpDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.8
Control Protocol Disposition for VTP (VLAN Trunking Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2003).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileDtpDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.9
Control Protocol Disposition for DTP (Dynamic Trunking). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2004).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfilePvstpPlusDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.10
Control Protocol Disposition for Spanning Tree PVSTP+. MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x10B).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileUplinkFastDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.11
Control Protocol Disposition for STP UplinkFast. MAC Address (01:00:0C:CD:CD:CD), Ethertype(0x200A).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileVlanBridgeDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.12
Control Protocol Disposition for VLAN Bridge. MAC Address (01:00:0C:CD:CD:CE), Ethertype(0x10C).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileL2PTDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.13
Control Protocol Disposition for Layer 2 Protocol Tunnelling(L2PT). MAC Address (01:00:0C:CD:CD:D0).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileBridgeGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.14
Deprecated - individual dispositions available for each MAC. Bridge Group Control Protocol Disposition Type. This includes BPDU, PAUSE (IEEE 802.3x Flow Control), LACP (Link Aggregation), LACP Marker (Marker), EFM OAM (IEEE 802.3 ah) and IEEE 802.1x Port Authentication, besides reserved MAC addresses from 01:80:C2:00:00:04 thru 01:80:C2:00:00:0F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileBPDUDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.15
Control Protocol Disposition for IEEE Spanning Tree(STP), MSTP (Multiple Spanning Tree) and RSTP (Rapid Reconfiguration of Spanning Tree). MAC Address (01:80:C2:00:00:00).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfilePauseDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.16
Control Protocol Disposition for IEEE 802.3x Flow Control (PAUSE frames).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileLACPDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.17
Control Protocol Disposition for 802.3ad Link Aggregation Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(01).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileLACPMarkerDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.18
Control Protocol Disposition for IEEE 802.3ad Marker Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(02).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileEfmOamDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.19
Control Protocol Disposition for IEEE 802.3ah EFM OAM. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(03).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileSSMDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.20
Control Protocol Disposition for Sync Status Messages. MAC Address (01:80:C2:00:00:02), Ethertype (0x19A7), Subtype(0A).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfilePortAuthenDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.21
Control Protocol Disposition for IEEE 802.1x Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x888E).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileBridgeReservedDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.22
Deprecated - individual dispositions available for each MAC. Control Protocol Disposition for Range of MAC Addresses from 01:80:C2:00:00:04 to 01:80:C2:00:00:0F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileLANBridgesDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.23
Control Protocol Disposition for IEEE 802.1d LAN Bridge Managment. MAC Address (01:80:C2:00:00:10).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileGARPGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.24
Deprecated - each GARP Group protocol has its own disposition. Group Disposition type which includes GMRP, GVRP and MAC Address from range 01:80:C2:00:00:22 to 01:80:C2:00:00:2F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileGMRPDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.25
Control Protocol Disposition for GARP Multicast Registration Protocol. MAC Address (01:80:C2:00:00:20).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileGVRPDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.26
Control Protocol Disposition for GARP VLAN Registration Protocol. MAC Address (01:80:C2:00:00:22).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileGARPDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.27
Group Disposition type which includes GMRP, GVRP and MAC Address from range 01:80:C2:00:00:20 to 01:80:C2:00:00:2F.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileLldpDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.28
Deprecated - each LLDP MAC protocol has its own disposition. Control Protocol Disposition for LLDP.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileStorageType 1.3.6.1.4.1.2544.1.12.4.1.33.1.29
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmPortCpdProfileRowStatus 1.3.6.1.4.1.2544.1.12.4.1.33.1.30
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmCpdProfileRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmCpdProfileRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmCpdProfileRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmPortCpdProfileMac00DispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.31
MAC Address 01:80:C2:00:00:00 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac01DispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.32
MAC Address 01:80:C2:00:00:01 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac02DispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.33
MAC Address 01:80:C2:00:00:02 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac03DispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.34
MAC Address 01:80:C2:00:00:03 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac04DispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.35
MAC Address 01:80:C2:00:00:04 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac05DispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.36
MAC Address 01:80:C2:00:00:05 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac06DispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.37
MAC Address 01:80:C2:00:00:06 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac07DispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.38
MAC Address 01:80:C2:00:00:07 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac08DispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.39
MAC Address 01:80:C2:00:00:08 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac09DispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.40
MAC Address 01:80:C2:00:00:09 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac0ADispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.41
MAC Address 01:80:C2:00:00:0A Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac0BDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.42
MAC Address 01:80:C2:00:00:0B Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac0CDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.43
MAC Address 01:80:C2:00:00:0C Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac0DDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.44
MAC Address 01:80:C2:00:00:0D Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac0EDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.45
MAC Address 01:80:C2:00:00:0E Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileMac0FDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.46
MAC Address 01:80:C2:00:00:0F Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileNearestLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.47
The nearest lldp Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileNonTpmrLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.48
The non tp mr lldp Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileCustomerLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.49
The customer lldp Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmPortCpdProfileELMIDispType 1.3.6.1.4.1.2544.1.12.4.1.33.1.50
The ELMI Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileTable 1.3.6.1.4.1.2544.1.12.4.1.34
A list of entries corresponding to System Control Protocol Disposition V3 profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmFlowPointCpdProfileEntry

cmFlowPointCpdProfileEntry 1.3.6.1.4.1.2544.1.12.4.1.34.1
A conceptual row in the cmFlowPointCpdProfileTable. These entries represent a Control Protocol Disposition of a flow point filtering criteria of the System.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmFlowPointCpdProfileEntry  

cmFlowPointCpdProfileIndex 1.3.6.1.4.1.2544.1.12.4.1.34.1.1
Unique Index value to access the CPD profile row.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

cmFlowPointCpdProfileName 1.3.6.1.4.1.2544.1.12.4.1.34.1.2
This object describes the alias of the cpd V3 profile entry.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

cmFlowPointCpdProfileCiscoGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.3
Deprecated - each Cisco protocol has its own disposition. Control Protocol Disposition for Cisco Group. This includes ISL, PAGP, UDLD, CDP, VTP, DTP, PSVTP+, UplinkFast, VLAN Bridge, L2PT. Note that a specific protocol filter overrides the group setting.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileIslDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.4
Control Protocol Disposition for ISL (Inter Switch Link). MAC Address (01:00:0C:00:00:00).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfilePagpDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.5
Control Protocol Disposition for PAGP (Port Aggregation Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x104).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileUdldDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.6
Control Protocol Disposition for UDLD (Unidirectional Link Detection). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x111).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileCdpDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.7
Control Protocol Disposition for CDP (Cisco Discovery Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2000).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileVtpDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.8
Control Protocol Disposition for VTP (VLAN Trunking Protocol). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2003).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileDtpDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.9
Control Protocol Disposition for DTP (Dynamic Trunking). MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x2004).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfilePvstpPlusDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.10
Control Protocol Disposition for Spanning Tree PVSTP+. MAC Address (01:00:0C:CC:CC:CC), Ethertype(0x10B).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileUplinkFastDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.11
Control Protocol Disposition for STP UplinkFast. MAC Address (01:00:0C:CD:CD:CD), Ethertype(0x200A).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileVlanBridgeDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.12
Control Protocol Disposition for VLAN Bridge. MAC Address (01:00:0C:CD:CD:CE), Ethertype(0x10C).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileL2PTDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.13
Control Protocol Disposition for Layer 2 Protocol Tunnelling(L2PT). MAC Address (01:00:0C:CD:CD:D0).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileBridgeGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.14
Deprecated - individual dispositions available for each MAC. Bridge Group Control Protocol Disposition Type. This includes BPDU, PAUSE (IEEE 802.3x Flow Control), LACP (Link Aggregation), LACP Marker (Marker), EFM OAM (IEEE 802.3 ah) and IEEE 802.1x Port Authentication, besides reserved MAC addresses from 01:80:C2:00:00:04 thru 01:80:C2:00:00:0F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileBPDUDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.15
Control Protocol Disposition for IEEE Spanning Tree(STP), MSTP (Multiple Spanning Tree) and RSTP (Rapid Reconfiguration of Spanning Tree). MAC Address (01:80:C2:00:00:00).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfilePauseDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.16
Control Protocol Disposition for IEEE 802.3x Flow Control (PAUSE frames).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileLACPDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.17
Control Protocol Disposition for 802.3ad Link Aggregation Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(01).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileLACPMarkerDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.18
Control Protocol Disposition for IEEE 802.3ad Marker Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(02).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileEfmOamDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.19
Control Protocol Disposition for IEEE 802.3ah EFM OAM. MAC Address (01:80:C2:00:00:03), Ethertype (0x8809), Subtype(03).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileSSMDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.20
Control Protocol Disposition for Sync Status Messages. MAC Address (01:80:C2:00:00:02), Ethertype (0x19A7), Subtype(0A).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfilePortAuthenDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.21
Control Protocol Disposition for IEEE 802.1x Protocol. MAC Address (01:80:C2:00:00:03), Ethertype (0x888E).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileBridgeReservedDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.22
Deprecated - individual dispositions available for each MAC. Control Protocol Disposition for Range of MAC Addresses from 01:80:C2:00:00:04 to 01:80:C2:00:00:0F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileLANBridgesDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.23
Control Protocol Disposition for IEEE 802.1d LAN Bridge Managment. MAC Address (01:80:C2:00:00:10).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileGARPGroupDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.24
Deprecated - each GARP Group protocol has its own disposition. Group Disposition type which includes GMRP, GVRP and MAC Address from range 01:80:C2:00:00:22 to 01:80:C2:00:00:2F.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileGMRPDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.25
Control Protocol Disposition for GARP Multicast Registration Protocol. MAC Address (01:80:C2:00:00:20).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileGVRPDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.26
Control Protocol Disposition for GARP VLAN Registration Protocol. MAC Address (01:80:C2:00:00:22).
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileGARPDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.27
Group Disposition type which includes GMRP, GVRP and MAC Address from range 01:80:C2:00:00:20 to 01:80:C2:00:00:2F.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileLldpDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.28
Deprecated - each LLDP MAC protocol has its own disposition. Control Protocol Disposition for LLDP.
Status: deprecated Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileStorageType 1.3.6.1.4.1.2544.1.12.4.1.34.1.29
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmFlowPointCpdProfileRowStatus 1.3.6.1.4.1.2544.1.12.4.1.34.1.30
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmCpdProfileRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmCpdProfileRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmCpdProfileRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmFlowPointCpdProfileMac00DispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.31
MAC Address 01:80:C2:00:00:00 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac01DispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.32
MAC Address 01:80:C2:00:00:01 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac02DispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.33
MAC Address 01:80:C2:00:00:02 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac03DispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.34
MAC Address 01:80:C2:00:00:03 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac04DispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.35
MAC Address 01:80:C2:00:00:04 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac05DispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.36
MAC Address 01:80:C2:00:00:05 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac06DispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.37
MAC Address 01:80:C2:00:00:06 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac07DispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.38
MAC Address 01:80:C2:00:00:07 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac08DispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.39
MAC Address 01:80:C2:00:00:08 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac09DispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.40
MAC Address 01:80:C2:00:00:09 Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac0ADispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.41
MAC Address 01:80:C2:00:00:0A Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac0BDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.42
MAC Address 01:80:C2:00:00:0B Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac0CDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.43
MAC Address 01:80:C2:00:00:0C Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac0DDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.44
MAC Address 01:80:C2:00:00:0D Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac0EDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.45
MAC Address 01:80:C2:00:00:0E Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileMac0FDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.46
MAC Address 01:80:C2:00:00:0F Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileNearestLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.47
The nearest lldp Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileNonTpmrLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.48
The non tp mr lldp Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileCustomerLLDPDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.49
The customer lldp Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmFlowPointCpdProfileELMIDispType 1.3.6.1.4.1.2544.1.12.4.1.34.1.50
The ELMI Disposition type.
Status: current Access: read-write
OBJECT-TYPE    
  CmControlProtocolDispType  

cmEthernetTrafficPortCpdTable 1.3.6.1.4.1.2544.1.12.4.1.35
A list of entries corresponding to Ethernet Port CPD for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetTrafficPortCpdEntry

cmEthernetTrafficPortCpdEntry 1.3.6.1.4.1.2544.1.12.4.1.35.1
A conceptual row in the cmEthernetTrafficPortCpdTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetTrafficPortCpdEntry  

cmEthernetTrafficPortCpdIndex 1.3.6.1.4.1.2544.1.12.4.1.35.1.1
An arbitrary integer index value used to uniquely identify this CPD Service Entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

cmEthernetTrafficPortAssociatedCpdProfile 1.3.6.1.4.1.2544.1.12.4.1.35.1.2
An integer index value used to apply cmCpdProfile configure, corresponding to cmCpdProfileIndex.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmEthernetFlowPointCpdTable 1.3.6.1.4.1.2544.1.12.4.1.36
A list of entries corresponding to Ethernet Flow Point CPD for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetFlowPointCpdEntry

cmEthernetFlowPointCpdEntry 1.3.6.1.4.1.2544.1.12.4.1.36.1
A conceptual row in the cmEthernetFlowPointCpdTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetFlowPointCpdEntry  

cmEthernetFlowPointCpdIndex 1.3.6.1.4.1.2544.1.12.4.1.36.1.1
An arbitrary integer index value used to uniquely identify this CPD Service Entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

cmEthernetFlowPointAssociatedCpdProfile 1.3.6.1.4.1.2544.1.12.4.1.36.1.2
An integer index value used to apply cmCpdProfile configure, corresponding to cmCpdProfileIndex.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmTrafficAclProfileTable 1.3.6.1.4.1.2544.1.12.4.1.37
A list of entries corresponding to the Traffic Profile Rules Entry. It provides upto 4000 Traffic ACL Rules to be configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmTrafficAclProfileEntry

cmTrafficAclProfileEntry 1.3.6.1.4.1.2544.1.12.4.1.37.1
An entry containing information applicable to a system ACL Profile that can be configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmTrafficAclProfileEntry  

cmTrafficAclProfileIndex 1.3.6.1.4.1.2544.1.12.4.1.37.1.1
An arbitrary integer index value used to uniquely identify Traffic ACL profile entry.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

cmTrafficAclProfileName 1.3.6.1.4.1.2544.1.12.4.1.37.1.2
This object describes the alias of the Acl profile entry.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

cmTrafficAclProfileStorageType 1.3.6.1.4.1.2544.1.12.4.1.37.1.3
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmTrafficAclProfileRowStatus 1.3.6.1.4.1.2544.1.12.4.1.37.1.4
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmTrafficAclProfileRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmTrafficAclProfileRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmTrafficAclProfileRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmTrafficAclRulesTable 1.3.6.1.4.1.2544.1.12.4.1.38
A list of entries corresponding to the Traffic ACL Rules Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmTrafficAclRulesEntry

cmTrafficAclRulesEntry 1.3.6.1.4.1.2544.1.12.4.1.38.1
An entry containing information applicable to a system ACL Rules that can be configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmTrafficAclRulesEntry  

cmTrafficAclRulesIndex 1.3.6.1.4.1.2544.1.12.4.1.38.1.1
An arbitrary integer index value used to uniquely identify Traffic ACL profile entry. The manager may not assume any particular semantics or meaning to this index, except that it identifies a logical row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

cmTrafficAclFilterAction 1.3.6.1.4.1.2544.1.12.4.1.38.1.2
Currently, 'permit' and 'deny' are supported.
Status: current Access: read-write
OBJECT-TYPE    
  CmTrafficAclFilterActionType  

cmTrafficAclFilterType 1.3.6.1.4.1.2544.1.12.4.1.38.1.3
This object describes the Acl filter type.
Status: current Access: read-write
OBJECT-TYPE    
  CmTrafficAclFilterType  

cmTrafficAclEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.4
This object enables/disables the Acl entity.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclSrcMacAddr 1.3.6.1.4.1.2544.1.12.4.1.38.1.5
The source mac address of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmTrafficAclSrcMacAddrEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.6
This object enables/disables source MAC address of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclDstMacAddr 1.3.6.1.4.1.2544.1.12.4.1.38.1.7
The destination MAC address of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

cmTrafficAclDstMacAddrEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.8
This object enables/disables destination MAC address of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclSrcIpFilterEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.9
This object enable/disable Source IPV4 or IPV6 address filter criteria.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclDstIpFilterEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.10
This object enable/disable Destination IPV4 or IPV6 address filter criteria.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclSrcIpV4Addr 1.3.6.1.4.1.2544.1.12.4.1.38.1.11
The source IP address of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

cmTrafficAclSrcIpV4AddrMask 1.3.6.1.4.1.2544.1.12.4.1.38.1.12
The source IP mask of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

cmTrafficAclDstIpV4Addr 1.3.6.1.4.1.2544.1.12.4.1.38.1.13
The destination IP address of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

cmTrafficAclDstIpV4AddrMask 1.3.6.1.4.1.2544.1.12.4.1.38.1.14
The destination IP mask of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

cmTrafficAclSrcIpV6Addr 1.3.6.1.4.1.2544.1.12.4.1.38.1.15
The source IPV6 address of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  Ipv6Address  

cmTrafficAclSrcIpV6AddrMask 1.3.6.1.4.1.2544.1.12.4.1.38.1.16
The source IPV6 mask of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  Ipv6Address  

cmTrafficAclDstIpV6Addr 1.3.6.1.4.1.2544.1.12.4.1.38.1.17
The destination IPV6 address of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  Ipv6Address  

cmTrafficAclDstIpV6AddrMask 1.3.6.1.4.1.2544.1.12.4.1.38.1.18
The destination IPV6 mask of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  Ipv6Address  

cmTrafficAclTcpUdpSrcPortNum 1.3.6.1.4.1.2544.1.12.4.1.38.1.19
This object describes TCP/UDP minimum source port number of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cmTrafficAclTcpUdpSrcPortMask 1.3.6.1.4.1.2544.1.12.4.1.38.1.20
This object describes TCP/UDP maximum source port number of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cmTrafficAclTcpUdpSrcPortEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.21
This object enables/disables TCP/UDP source port of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclTcpUdpDstPortNum 1.3.6.1.4.1.2544.1.12.4.1.38.1.22
This object describes TCP/UDP minimum destination port number of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cmTrafficAclTcpUdpDstPortMask 1.3.6.1.4.1.2544.1.12.4.1.38.1.23
This object describes TCP/UDP maximum destination port number of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

cmTrafficAclTcpUdpDstPortEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.24
This object enables/disables TCP/UDP destination port of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclIpQosType 1.3.6.1.4.1.2544.1.12.4.1.38.1.25
This object describes QosType Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  CmTrafficACLPriorityType  

cmTrafficAclIpQosValue 1.3.6.1.4.1.2544.1.12.4.1.38.1.26
This object describes QOS value of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmTrafficAclIpQosTypeEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.27
This object enables/disables qos type of acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclVlanId 1.3.6.1.4.1.2544.1.12.4.1.38.1.28
This object describes the vlan Id of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

cmTrafficAclVlanIdEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.29
This object enables/disables Vlan Id of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclVlanPriority 1.3.6.1.4.1.2544.1.12.4.1.38.1.30
This object describes the Vlan Priority of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmTrafficAclVlanPriorityEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.31
This object enables/disables Vlan Priority of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclProtocolType 1.3.6.1.4.1.2544.1.12.4.1.38.1.32
This object describes protocol type of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  CmTrafficAclProtocolType  

cmTrafficAclProtocolTypeEnabled 1.3.6.1.4.1.2544.1.12.4.1.38.1.33
This object enables/disables protocol type of Acl entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficAclStorageType 1.3.6.1.4.1.2544.1.12.4.1.38.1.34
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmTrafficAclRowStatus 1.3.6.1.4.1.2544.1.12.4.1.38.1.35
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmTrafficAclRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmTrafficAclRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmTrafficAclRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmQosPolicerProfileTable 1.3.6.1.4.1.2544.1.12.4.1.39
A list of entries corresponding to Quality of Service Policer for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmQosPolicerProfileEntry

cmQosPolicerProfileEntry 1.3.6.1.4.1.2544.1.12.4.1.39.1
A conceptual row in the cmQosPolicerProfileTable. These entries represent a Quality of Service Policer.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmQosPolicerProfileEntry  

cmQosPolicerProfileIndex 1.3.6.1.4.1.2544.1.12.4.1.39.1.1
This object defines the Policer profile ID. Up to 1000 profiles can be specified per system.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..65535  

cmQosPolicerProfileName 1.3.6.1.4.1.2544.1.12.4.1.39.1.2
This object defines the alias for this profile
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

cmQosPolicerProfileCIRLo 1.3.6.1.4.1.2544.1.12.4.1.39.1.3
This object allows specification of the Commited Information Rate(CIR) on Policer Profile. This represents the lower 32 bits of the CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosPolicerProfileCIRHi 1.3.6.1.4.1.2544.1.12.4.1.39.1.4
This object allows specification of the Commited Information Rate(CIR) on Policer Profile. This represents the upper 32 bits of the CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosPolicerProfileEIRLo 1.3.6.1.4.1.2544.1.12.4.1.39.1.5
This object allows specification of the Excess Information Rate(EIR) on the Policer Profile. This represents the lower 32 bits of the EIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosPolicerProfileEIRHi 1.3.6.1.4.1.2544.1.12.4.1.39.1.6
This object allows specification of the Excess Information Rate(EIR) on the Policer Profile. This represents the upper 32 bits of the EIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmQosPolicerProfileCBS 1.3.6.1.4.1.2544.1.12.4.1.39.1.7
This object allows specification of the Commited Burst Size (CBS) on Policer Profile.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cmQosPolicerProfileEBS 1.3.6.1.4.1.2544.1.12.4.1.39.1.8
This object allows specification of the Excess Burst Size (EBS) on the Policer Profile.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cmQosPolicerProfileColorMode 1.3.6.1.4.1.2544.1.12.4.1.39.1.9
This object allows specification of Policer Color Mode as 'color-aware' or 'color-blind'.
Status: current Access: read-create
OBJECT-TYPE    
  PolicerColorMode  

cmQosPolicerProfileCouplingFlag 1.3.6.1.4.1.2544.1.12.4.1.39.1.10
This object allows specification of Policer Coupling Flag. When coupling is enabled, tokens that would normally be added to the C-bucket are passed to the E-bucket only once the CIR bucket has reached its CBS level. Therefore under this condition the E-bucket is being filled at the rate of CIR + EIR. Normally the long term average of frames declared yellow, which is bounded by the EIR. Coupling is a function to allow the long term average of frames declared yellow to be bounded by CIR + EIR. This allows a higher volume of yellow frames to be delivered/received if the arrival of green marked frames is low. Tokens from the E-bucket do NOT get passed to the C-bucket once the EBS level has been reached. Enabling coupling in combination with a provisioned EIR of 0 allows for a single rate three color marking (srTCM) algorithm to be established. In this situation the E-bucket is filled at the CIR rate in the case the C-bucket is filled to its CBS level.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmQosPolicerProfileStorageType 1.3.6.1.4.1.2544.1.12.4.1.39.1.11
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmQosPolicerProfileRowStatus 1.3.6.1.4.1.2544.1.12.4.1.39.1.12
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmQosPolicerProfileRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmQosPolicerProfileRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmQosPolicerProfileRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmQosQueueProfileTable 1.3.6.1.4.1.2544.1.12.4.1.40
A list of entries corresponding to Quality of Service Queue for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmQosQueueProfileEntry

cmQosQueueProfileEntry 1.3.6.1.4.1.2544.1.12.4.1.40.1
A conceptual row in the cmQosQueueProfileTable. These entries represent a Quality of Service Queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmQosQueueProfileEntry  

cmQosQueueProfileIndex 1.3.6.1.4.1.2544.1.12.4.1.40.1.1
This object defines the Queue profile ID. Up to 64 profiles can be specified per system.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..64  

cmQosQueueProfileName 1.3.6.1.4.1.2544.1.12.4.1.40.1.2
This object defines the alias for this profile
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

cmQosQueueProfileBufferSize 1.3.6.1.4.1.2544.1.12.4.1.40.1.3
This object defines the buffer size of the selected queues.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cmQosQueueProfileREDEnabled 1.3.6.1.4.1.2544.1.12.4.1.40.1.4
This object defines whether the WRED is enabled as congestion algorithm or not. If disabled, then the following RED parameters (cmQueueProfileWREDDp0MinTh, cmQueueProfileWREDDp0MaxTh and cmQueueProfileWREDDp0MaxProb) must not be specified.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmQosQueueProfileStorageType 1.3.6.1.4.1.2544.1.12.4.1.40.1.5
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmQosQueueProfileRowStatus 1.3.6.1.4.1.2544.1.12.4.1.40.1.6
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmQosQueueProfileRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmQosQueueProfileRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmQosQueueProfileRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmQosPolicerV2Table 1.3.6.1.4.1.2544.1.12.4.1.41
A list of entries corresponding to Quality of Service Policer for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmQosPolicerV2Entry

cmQosPolicerV2Entry 1.3.6.1.4.1.2544.1.12.4.1.41.1
A conceptual row in the cmQosPolicerV2Table. These entries represent a Quality of Service Policer.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmQosPolicerV2Entry  

cmQosPolicerV2Index 1.3.6.1.4.1.2544.1.12.4.1.41.1.1
The Policer Index that represents the COS level. Index 1 represents COS 0; Index 2 represents COS 1 and so on.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..8  

cmQosPolicerV2AdminState 1.3.6.1.4.1.2544.1.12.4.1.41.1.2
This object represents the Administrative State of the QOS Policer.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmQosPolicerV2OperationalState 1.3.6.1.4.1.2544.1.12.4.1.41.1.3
This object represents the Operational State of the QOS Policer.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmQosPolicerV2SecondaryState 1.3.6.1.4.1.2544.1.12.4.1.41.1.4
This object represents the Secondary State of the QOS Policer.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmQosPolicerV2ColorMarkingEnabled 1.3.6.1.4.1.2544.1.12.4.1.41.1.5
This object indicates the colorMarking state of the QOS Policer.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmQosPolicerV2AssociatedProfile 1.3.6.1.4.1.2544.1.12.4.1.41.1.6
This object define the queue profile ID to be used, it is associated with the cmQosPolicerProfileIndex.
Status: current Access: read-create
OBJECT-TYPE    
  VariablePointer  

cmQosPolicerV2StorageType 1.3.6.1.4.1.2544.1.12.4.1.41.1.7
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmQosPolicerV2RowStatus 1.3.6.1.4.1.2544.1.12.4.1.41.1.8
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmQosPolicerV2RowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmQosPolicerV2RowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmQosPolicerV2RowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmQosPolicerV2PolicingEnabled 1.3.6.1.4.1.2544.1.12.4.1.41.1.9
Whether enable or disable the functionality of policing for this COS.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmQosShaperV2Table 1.3.6.1.4.1.2544.1.12.4.1.42
A list of entries corresponding to Quality of Service ShaperV2 for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmQosShaperV2Entry

cmQosShaperV2Entry 1.3.6.1.4.1.2544.1.12.4.1.42.1
A conceptual row in the cmQosShaperV2Table. These entries represent a Quality of Service Shaper.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmQosShaperV2Entry  

cmQosShaperV2Index 1.3.6.1.4.1.2544.1.12.4.1.42.1.1
The ShaperV2 Index that represents the COS level. Index 1 represents COS 0; Index 2 represents COS 1 and so on.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..8  

cmQosShaperV2AdminState 1.3.6.1.4.1.2544.1.12.4.1.42.1.2
This object represents the Administrative State of the QOS Shaper.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmQosShaperV2OperationalState 1.3.6.1.4.1.2544.1.12.4.1.42.1.3
This object represents the Operational State of the QOS ShaperV2.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmQosShaperV2SecondaryState 1.3.6.1.4.1.2544.1.12.4.1.42.1.4
This object represents the Secondary State of the QOS QosShaperV2.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmQosShaperV2AssociatedQueueProfile 1.3.6.1.4.1.2544.1.12.4.1.42.1.5
This object defines the queue profile ID to be used, it is associated with the cmQosQueueProfileIndex.
Status: current Access: read-create
OBJECT-TYPE    
  VariablePointer  

cmQosShaperV2CIRLo 1.3.6.1.4.1.2544.1.12.4.1.42.1.6
This object specifies the Lower 32 bits of CIR.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmQosShaperV2CIRHi 1.3.6.1.4.1.2544.1.12.4.1.42.1.7
This object specifies the Higher 32 bits of CIR.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmQosShaperV2EIRLo 1.3.6.1.4.1.2544.1.12.4.1.42.1.8
This object specifies the Lower 32 bits of EIR.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmQosShaperV2EIRHi 1.3.6.1.4.1.2544.1.12.4.1.42.1.9
This object specifies the Higher 32 bits of EIR.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmQosShaperV2IngressAverageFrameSize 1.3.6.1.4.1.2544.1.12.4.1.42.1.10
This object defines the average frame size for accounting for Meter/Shaping.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 64..9600  

cmQosShaperV2StorageType 1.3.6.1.4.1.2544.1.12.4.1.42.1.11
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmQosShaperV2RowStatus 1.3.6.1.4.1.2544.1.12.4.1.42.1.12
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmQosShaperV2RowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmQosShaperV2RowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmQosShaperV2RowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmQosShaperV2AdditionalCIRLo 1.3.6.1.4.1.2544.1.12.4.1.42.1.13
This object specifies the Lower 32 bits of additional CIR.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmQosShaperV2AdditionalCIRHi 1.3.6.1.4.1.2544.1.12.4.1.42.1.14
This object specifies the Higher 32 bits of additional CIR.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmQosShaperV2WFQWeight 1.3.6.1.4.1.2544.1.12.4.1.42.1.15
Weight of queue to be scheduled by WFQ mechanism.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..64  

cmQosShaperV2ActualCIR 1.3.6.1.4.1.2544.1.12.4.1.42.1.16
This object specifies the actual CIR.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

cmQosShaperV2ActualEIR 1.3.6.1.4.1.2544.1.12.4.1.42.1.17
This object specifies the actual EIR.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

cmQosShaperV2LowLatencyControl 1.3.6.1.4.1.2544.1.12.4.1.42.1.18
This object specifies low latency control whether enabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmTrafficPortQosShaperTable 1.3.6.1.4.1.2544.1.12.4.1.43
A list of entries corresponding to Quality of Service Shaper for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmTrafficPortQosShaperEntry

cmTrafficPortQosShaperEntry 1.3.6.1.4.1.2544.1.12.4.1.43.1
A conceptual row in the cmTrafficPortQosShaperTable. These entries represent a Quality of Service Shaper.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmTrafficPortQosShaperEntry  

cmTrafficPortQosShaperIndex 1.3.6.1.4.1.2544.1.12.4.1.43.1.1
The ShaperV2 Index that represents the COS level. Index 1 represents COS 0; Index 2 represents COS 1 and so on.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..8  

cmTrafficPortQosShaperAdminState 1.3.6.1.4.1.2544.1.12.4.1.43.1.2
This object represents the Administrative State of the QOS Shaper.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmTrafficPortQosShaperOperationalState 1.3.6.1.4.1.2544.1.12.4.1.43.1.3
This object represents the Operational State of the QOS ShaperV2.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmTrafficPortQosShaperSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.43.1.4
This object represents the Secondary State of the QOS LagQosShaper.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmTrafficPortQosShaperAssociatedQueueProfile 1.3.6.1.4.1.2544.1.12.4.1.43.1.5
This object defines the queue profile ID to be used, it is associated with the cmQosQueueProfileIndex.
Status: current Access: read-create
OBJECT-TYPE    
  VariablePointer  

cmTrafficPortQosShaperBufferSize 1.3.6.1.4.1.2544.1.12.4.1.43.1.6
This object defines the buffer size of Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cmTrafficPortQosShaperCIRLo 1.3.6.1.4.1.2544.1.12.4.1.43.1.7
This object specifies the Lower 32 bits of CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmTrafficPortQosShaperCIRHi 1.3.6.1.4.1.2544.1.12.4.1.43.1.8
This object specifies the Higher 32 bits of CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmTrafficPortQosShaperEIRLo 1.3.6.1.4.1.2544.1.12.4.1.43.1.9
This object specifies the Lower 32 bits of EIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmTrafficPortQosShaperEIRHi 1.3.6.1.4.1.2544.1.12.4.1.43.1.10
This object specifies the Higher 32 bits of EIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmTrafficPortQosShaperStorageType 1.3.6.1.4.1.2544.1.12.4.1.43.1.11
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmTrafficPortQosShaperRowStatus 1.3.6.1.4.1.2544.1.12.4.1.43.1.12
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmTrafficPortQosShaperRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmTrafficPortQosShaperRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmTrafficPortQosShaperRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmTrafficPortQosShaperIngressAverageFrameSize 1.3.6.1.4.1.2544.1.12.4.1.43.1.13
This object defines the average frame size for accounting for Meter/Shaping.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 64..9600  

cmTrafficPortQosShaperAdditionalCIRLo 1.3.6.1.4.1.2544.1.12.4.1.43.1.14
This object specifies the Lower 32 bits of additional CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmTrafficPortQosShaperAdditionalCIRHi 1.3.6.1.4.1.2544.1.12.4.1.43.1.15
This object specifies the Higher 32 bits of additional CIR.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cmTrafficAclRscAllocation 1.3.6.1.4.1.2544.1.12.4.1.44
This object is defined to set traffic acl resource allocation. Supported actions are: all-bk-l2(1) - all bank allocated to l2. all-bk-l2-ipv4(2) - all bank allocated to l2/ipv4. two-bk-l2-ipv4(3) - two thirds allocated to l2/ipv4, the left belongs to ipv6. one-bk-l2-ipv4(4) - one thirds allocated to l2/ipv4, the left belongs to ipv6. none-bk-l2-ipv4(5) - all bank allocated to ipv6.
Status: current Access: read-write
OBJECT-TYPE    
  CmAclConfiguration  

f3NetPortQosShaperTable 1.3.6.1.4.1.2544.1.12.4.1.45
A list of entries corresponding to Ethernet Network Port Quality of Service Shaper for configuration purposes. These shapers can be managed when the Network Port is in evpl mode and are relevant for traffic in the access to network direction.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    F3NetPortQosShaperEntry

f3NetPortQosShaperEntry 1.3.6.1.4.1.2544.1.12.4.1.45.1
A conceptual row in the f3NetPortQosShaperTable. These entries represent a Quality of Service Shaper.
Status: current Access: not-accessible
OBJECT-TYPE    
  F3NetPortQosShaperEntry  

f3NetPortQosShaperIndex 1.3.6.1.4.1.2544.1.12.4.1.45.1.1
The unique integer index value corresponding to a Quality of Service Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..8  

f3NetPortQosShaperDirection 1.3.6.1.4.1.2544.1.12.4.1.45.1.2
The direction of the Quality of Service Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  TrafficDirection  

f3NetPortQosShaperAdminState 1.3.6.1.4.1.2544.1.12.4.1.45.1.3
This object represents the Administrative State of the QOS Shaper.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

f3NetPortQosShaperOperationalState 1.3.6.1.4.1.2544.1.12.4.1.45.1.4
This object represents the Operational State of the QOS Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

f3NetPortQosShaperSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.45.1.5
This object represents the Secondary State of the QOS Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

f3NetPortQosShaperCIRLo 1.3.6.1.4.1.2544.1.12.4.1.45.1.6
This object represents the Commited Information Rate(CIR) (Lower 32 bits)of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperCIRHi 1.3.6.1.4.1.2544.1.12.4.1.45.1.7
This object represents the Commited Information Rate(CIR) (Higher 32 bits) of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperEIRLo 1.3.6.1.4.1.2544.1.12.4.1.45.1.8
This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperEIRHi 1.3.6.1.4.1.2544.1.12.4.1.45.1.9
This object represents the Excess Information Rate(EIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperCBS 1.3.6.1.4.1.2544.1.12.4.1.45.1.10
This object represents the Commited Burst Size (CBS) of the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperEBS 1.3.6.1.4.1.2544.1.12.4.1.45.1.11
This object represents the Excess Burst Size (EBS) of the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperBufferSize 1.3.6.1.4.1.2544.1.12.4.1.45.1.12
This object represents the Buffer Size of the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperCOS 1.3.6.1.4.1.2544.1.12.4.1.45.1.13
This object provides the COS (Class of Service) value for the QOS Shaper.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

f3NetPortQosShaperSoamCIRLo 1.3.6.1.4.1.2544.1.12.4.1.45.1.14
This object represents the Soam Commited Information Rate(SOAM-CIR) (Lower 32 bits)of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperSoamCIRHi 1.3.6.1.4.1.2544.1.12.4.1.45.1.15
This object represents the Soam Commited Information Rate(SOAM-CIR) (Higher 32 bits) of a Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperSoamEIRLo 1.3.6.1.4.1.2544.1.12.4.1.45.1.16
This object represents the Soam Excess Information Rate(SOAM-EIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperSoamEIRHi 1.3.6.1.4.1.2544.1.12.4.1.45.1.17
This object represents the Soam Excess Information Rate(SOAM-EIR) (Higher 32 bits) on the Shaper.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperWredGreenMinQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.45.1.18
This object represents the Wred green packet min queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperWredGreenMaxQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.45.1.19
This object represents the Wred green packet max queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperWredGreenDropProbability 1.3.6.1.4.1.2544.1.12.4.1.45.1.20
This object represents the Wred green packet drop probability.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperWredYellowMinQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.45.1.21
This object represents the Wred yellow packet min queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperWredYellowMaxQueueThreshold 1.3.6.1.4.1.2544.1.12.4.1.45.1.22
This object represents the Wred yellow packet max queue threshold value.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3NetPortQosShaperWredYellowDropProbability 1.3.6.1.4.1.2544.1.12.4.1.45.1.23
This object represents the Wred yellow packet drop probability.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

f3Usb3GDCNPortTable 1.3.6.1.4.1.2544.1.12.4.1.46
3G DCN Port table. The table contains parameters of 3G USB modem.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    F3Usb3GDCNPortEntry

f3Usb3GDCNPortEntry 1.3.6.1.4.1.2544.1.12.4.1.46.1
A conceptual row in the f3Usb3GDCNPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  F3Usb3GDCNPortEntry  

f3Usb3GDCNPortIndex 1.3.6.1.4.1.2544.1.12.4.1.46.1.1
An integer index value used to uniquely identify this Ethernet Access Port within a card. Note that each Ethernet Access Port is uniquely identified by the indices neIndex, shelfIndex, slotIndex, f3Usb3GDCNPortIndex
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

f3Usb3GDCNPortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.46.1.2
This object has the same value as ifIndex for G3 DCN Port. An integer index value used to uniquely identify this G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

f3Usb3GDCNPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.46.1.3
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

f3Usb3GDCNPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.46.1.4
This object represents the Administrative State of the G3 DCN Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

f3Usb3GDCNPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.46.1.5
This object represents the Operational State of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

f3Usb3GDCNPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.46.1.6
This object represents the Secondary State of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

f3Usb3GDCNPortVendorName 1.3.6.1.4.1.2544.1.12.4.1.46.1.7
This object provides the Vendor Name of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

f3Usb3GDCNPortModel 1.3.6.1.4.1.2544.1.12.4.1.46.1.8
This object provides the Model of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

f3Usb3GDCNPortFSN 1.3.6.1.4.1.2544.1.12.4.1.46.1.9
This object provides the Factory Serial Number of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

f3Usb3GDCNPortIMEI 1.3.6.1.4.1.2544.1.12.4.1.46.1.10
This object provides the International Mobile Equipment Identity of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

f3Usb3GDCNPortHardwareVersion 1.3.6.1.4.1.2544.1.12.4.1.46.1.11
This object provides the Hardware Version of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

f3Usb3GDCNPortFirmwareVersion 1.3.6.1.4.1.2544.1.12.4.1.46.1.12
This object provides the Firmware Version of the G3 DCN Port..
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

f3Usb3GDCNPortSIMStatus 1.3.6.1.4.1.2544.1.12.4.1.46.1.13
This object provides the SIM card Status of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  F3Usb3GSimCardState  

f3Usb3GDCNPortPINLeftChances 1.3.6.1.4.1.2544.1.12.4.1.46.1.14
This object provides the Left Chances for PIN input of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

f3Usb3GDCNPortPUKLeftChances 1.3.6.1.4.1.2544.1.12.4.1.46.1.15
This object provides the Left Chances for PUK input of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

f3Usb3GDCNPortConnectionStatus 1.3.6.1.4.1.2544.1.12.4.1.46.1.16
This object provides the Wirless Connection Status of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  F3Usb3GNetworkConnectionState  

f3Usb3GDCNPortRSSI 1.3.6.1.4.1.2544.1.12.4.1.46.1.17
This object provides the Received Signal Strength Indication of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  F3Usb3GRecvSignalStrengthInd  

f3Usb3GDCNPortSpeed 1.3.6.1.4.1.2544.1.12.4.1.46.1.18
This object provides the Connection Speed of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

f3Usb3GDCNPortMTU 1.3.6.1.4.1.2544.1.12.4.1.46.1.19
This object provides the MTU of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

f3Usb3GDCNPortProviderName 1.3.6.1.4.1.2544.1.12.4.1.46.1.20
This object provides the Wireless Service Provider Name of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

f3Usb3GDCNPortDNS1 1.3.6.1.4.1.2544.1.12.4.1.46.1.21
This first DNS of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

f3Usb3GDCNPortDNS2 1.3.6.1.4.1.2544.1.12.4.1.46.1.22
This second DNS of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

f3Usb3GDCNPortAPN 1.3.6.1.4.1.2544.1.12.4.1.46.1.23
This object allows configure the Access Point Name of the G3 DCN Port.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

f3Usb3GDCNPortUserName 1.3.6.1.4.1.2544.1.12.4.1.46.1.24
This object allows configure the User Name of the G3 DCN Port.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

f3Usb3GDCNPortPassword 1.3.6.1.4.1.2544.1.12.4.1.46.1.25
This object allows configure the Password of the G3 DCN Port.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

f3Usb3GDCNPortDailNumber 1.3.6.1.4.1.2544.1.12.4.1.46.1.26
This object allows configure the Dail Number of the G3 DCN Port.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

f3Usb3GDCNPortRedialTimer 1.3.6.1.4.1.2544.1.12.4.1.46.1.27
This object allows configure the Retail Timer of the G3 DCN Port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

f3Usb3GDCNPortCurrentPinCode 1.3.6.1.4.1.2544.1.12.4.1.46.1.28
This object is the Current Pin Code.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

f3Usb3GDCNPortNewPinCode 1.3.6.1.4.1.2544.1.12.4.1.46.1.29
This object is the New Pin code.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

f3Usb3GDCNPortConfirmPinCode 1.3.6.1.4.1.2544.1.12.4.1.46.1.30
This object is the Confirm Pin Code.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

f3Usb3GDCNPortCurrentPukCode 1.3.6.1.4.1.2544.1.12.4.1.46.1.31
This object is the Current Puk Code.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

f3Usb3GDCNPINCodeAction 1.3.6.1.4.1.2544.1.12.4.1.46.1.32
This Action is for PIN code operation.
Status: current Access: read-create
OBJECT-TYPE    
  F3Usb3GDCNPINCodeActionType  

f3Usb3GDCNPortStorageType 1.3.6.1.4.1.2544.1.12.4.1.46.1.33
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

f3Usb3GDCNPortRowStatus 1.3.6.1.4.1.2544.1.12.4.1.46.1.34
The status of this row. The f3Usb3GDCNPortRowStatus object may be modified if the associated instance of this object is equal to active(1), notInService(2), or notReady(3).
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

f3Usb3GDCNPortIMSI 1.3.6.1.4.1.2544.1.12.4.1.46.1.35
This object provides the International Mobile Subscriber Identity of the G3 DCN Port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

f3Usb3GDCNPortPINStatus 1.3.6.1.4.1.2544.1.12.4.1.46.1.36
This status of PIN/PUK
Status: current Access: read-only
OBJECT-TYPE    
  G3AuthStatus  

f3UsbDCNPortMobileNetworkType 1.3.6.1.4.1.2544.1.12.4.1.46.1.37
This object describe the mobile network type.
Status: current Access: read-only
OBJECT-TYPE    
  UsbDCNMobileNetworkType  

ocnStmTable 1.3.6.1.4.1.2544.1.12.4.1.47
A list of entries corresponding to OCn/STM interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OcnStmEntry

ocnStmEntry 1.3.6.1.4.1.2544.1.12.4.1.47.1
A conceptual row in the ocnStmTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  OcnStmEntry  

ocnStmIndex 1.3.6.1.4.1.2544.1.12.4.1.47.1.1
Unique index value associated with the OCn/STM interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

ocnStmIfIndex 1.3.6.1.4.1.2544.1.12.4.1.47.1.2
This object has the same value as ifIndex for OCn/STM interface. An integer index value used to uniquely identify this OCn/STM interface.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

ocnStmEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.47.1.3
Entity Index from ENTITY-MIB for this OCn/STM interface.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

ocnStmAdminState 1.3.6.1.4.1.2544.1.12.4.1.47.1.4
This object represents the Administrative State of the OCn/STM interface.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

ocnStmOperationalState 1.3.6.1.4.1.2544.1.12.4.1.47.1.5
This object represents the Operational State of the OCn/STM interface.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

ocnStmSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.47.1.6
This object represents the Secondary State of the OCn/STM interface.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

ocnStmSfpVendorName 1.3.6.1.4.1.2544.1.12.4.1.47.1.7
This object provides the vendor name of the SFP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

ocnStmSfpPartNumber 1.3.6.1.4.1.2544.1.12.4.1.47.1.8
This object provides the part number of the SFP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

ocnStmSfpSerialNumber 1.3.6.1.4.1.2544.1.12.4.1.47.1.9
This object provides the serial number of the SFP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

ocnStmSfpDateOfManufacture 1.3.6.1.4.1.2544.1.12.4.1.47.1.10
This object provides the date of manufacture of the SFP.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

ocnStmSfpConnectorValue 1.3.6.1.4.1.2544.1.12.4.1.47.1.11
This object provides the SFP connector value.
Status: current Access: read-only
OBJECT-TYPE    
  SfpConnectorValue  

ocnStmSfpLinkLength 1.3.6.1.4.1.2544.1.12.4.1.47.1.12
This object provides the SFP Link Length.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocnStmSfpLaserWaveLength 1.3.6.1.4.1.2544.1.12.4.1.47.1.13
This object provides the SFP Laser Wave Length in nano meters.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

ocnStmSfpLaserWaveLengthPicometer 1.3.6.1.4.1.2544.1.12.4.1.47.1.14
This object provide laser wavelength pico value. For example, laser wavelength is 1510.01, then ocnStmSfpLaserWaveLength=1510 and ocnStmSfpLaserWaveLengthPicometer=10.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ocnStmSfpMediaType 1.3.6.1.4.1.2544.1.12.4.1.47.1.15
This object provides the SFP Media Type.
Status: current Access: read-only
OBJECT-TYPE    
  SfpMediaType  

ocnStmMultiplexingStructures 1.3.6.1.4.1.2544.1.12.4.1.47.1.16
This object provides the TDM Multiplexing Structure base on OCn/STM interface.
Status: current Access: read-write
OBJECT-TYPE    
  MultiplexingStructure  

ocnStmEoTDMMode 1.3.6.1.4.1.2544.1.12.4.1.47.1.17
This object provides the TDM Mode base on OCn/STM interface. EoPDH means VCG container is PDH; EoTDM means VCG container is VC of SDH/SONET
Status: current Access: read-write
OBJECT-TYPE    
  EoTDMMode  

ocnStmLoopbackConfig 1.3.6.1.4.1.2544.1.12.4.1.47.1.18
This object allows to initiate loopbacks on on the OCn/STM interface.
Status: current Access: read-write
OBJECT-TYPE    
  CmLoopbackType  

ocnStmLoopbackStatus 1.3.6.1.4.1.2544.1.12.4.1.47.1.19
This object provides status of the current loopback on the OCn/STM interface.
Status: current Access: read-only
OBJECT-TYPE    
  CmLoopbackType  

ocnStmLoopbackTime 1.3.6.1.4.1.2544.1.12.4.1.47.1.20
This object allows to specify time for timed-loopbacks on on the OCn/STM interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..300  

ocnStmInsertingAIS 1.3.6.1.4.1.2544.1.12.4.1.47.1.21
This object allows to insert AIS-L out from OCn/STM interface when it is in maintenance state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ocnStmBerExcThreshold 1.3.6.1.4.1.2544.1.12.4.1.47.1.22
This object provide the threshold of B2EXC.
Status: current Access: read-write
OBJECT-TYPE    
  BitErrRate  

ocnStmBerDegThreshold 1.3.6.1.4.1.2544.1.12.4.1.47.1.23
This object provides the threshold of B2DEG.
Status: current Access: read-write
OBJECT-TYPE    
  BitErrRate  

ocnStmRxTrailTrace 1.3.6.1.4.1.2544.1.12.4.1.47.1.24
This object provides the recevied J0 on the OCn/STM interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

ocnStmTxTrailTrace 1.3.6.1.4.1.2544.1.12.4.1.47.1.25
This object provides the transmit J0 on the OCn/STM interface.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

ocnStmExpectedTrailTrace 1.3.6.1.4.1.2544.1.12.4.1.47.1.26
This object provides the expected J0 on the OCn/STM interface.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

ocnStmTrailTraceFormat 1.3.6.1.4.1.2544.1.12.4.1.47.1.27
This object provides the J0 length mode on the OCn/STM interface.
Status: current Access: read-write
OBJECT-TYPE    
  TrailTraceFormat  

ocnStmQLModeEnabled 1.3.6.1.4.1.2544.1.12.4.1.47.1.28
This object allows to specify whether the OCn/STM interface can be enabled/disabled for QL Mode. This object is only applicable for Synchronous OCn/STM interface, when ocnStmQLModeEnabled is set to true. When enabled, on receive side -port shall PEER the SSM (Sync Status Messages) slow protocol PDUs and take appropriate action When enabled, on transmit side -port shall periodically (once a second) transmit QL TLV information PDUs When disabled, on receive side, -port shall terminate and discard any SSM slow protocol PDUs When disabled, on transmit side -port shall not transmit any SSM slow protocol PDUs.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ocnStmExpectedQL 1.3.6.1.4.1.2544.1.12.4.1.47.1.29
This object allows to specify the expected QL when the OCn/STM interface is enabled for QL Mode. This object is only applicable for Synchronous OCn/STM interface, when ocnStmQLModeEnabled is set to true. This object allows the user to set a minimum expected received Quality Level on the port. The valid values depend upon the SYNC entity Network Clock Type. A value of None represents that a minimum Quality Level is not expected. The default value shall be None.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

ocnStmAssumedQL 1.3.6.1.4.1.2544.1.12.4.1.47.1.30
This object allows to specify the assumed QL on the OCn/STM interface. This object is only applicable for Synchronous OCn/STM interface. The Assumed QL is only meaningful if the Network Clock Type (see fsp150cm-sync.mib) is option1 and the port TransmitQL Mode is disabled and the port is being used as an input reference source. Under these conditions, the specified QL value is assumed to be the Quality Level of the non-failed reference.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

ocnStmReceivedQL 1.3.6.1.4.1.2544.1.12.4.1.47.1.31
This object provides the Received QL value for the OCn/STM interface. If the OCn/STM interface TransmitQL Mode is disabled, then the received QL value is not applicable.This object is only applicable for Synchronous OCn/STM interface.
Status: current Access: read-only
OBJECT-TYPE    
  SSMQualityLevel  

ocnStmTransmitQL 1.3.6.1.4.1.2544.1.12.4.1.47.1.32
This object provides the Transmitted QL value for the OCn/STM interface. If the OCn/STM interface TransmitQL Mode is disabled, then the received QL value is not applicable. This object is only applicable for Synchronous OCn/STM interface.
Status: current Access: read-only
OBJECT-TYPE    
  SSMQualityLevel  

ocnStmPortType 1.3.6.1.4.1.2544.1.12.4.1.47.1.33
This object represents the OCN/STM Port Type. Determines whether the OCN/STM port operates in OC or STM mode.
Status: current Access: read-only
OBJECT-TYPE    
  OCNSTMPortType  

ocnStmFreqSourceType 1.3.6.1.4.1.2544.1.12.4.1.47.1.34
This object represents the TDM Frequency source of OCN/STM port.
Status: current Access: read-write
OBJECT-TYPE    
  TDMFrequencySourceType  

ocnStmHighOrderPathType 1.3.6.1.4.1.2544.1.12.4.1.47.1.35
This object provides the High Order Path Type of the OCn/STM interface.
Status: current Access: read-write
OBJECT-TYPE    
  TDMPathType  

stsVcPathTable 1.3.6.1.4.1.2544.1.12.4.1.48
A list of entries corresponding to OCn Path.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    StsVcPathEntry

stsVcPathEntry 1.3.6.1.4.1.2544.1.12.4.1.48.1
A conceptual row in the stsVcPathTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  StsVcPathEntry  

stsVcPathParentIfIndex 1.3.6.1.4.1.2544.1.12.4.1.48.1.1
This object is its parent's ifindex. Based on the Multiplexing hierarchy, this object points to the container's interface index.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

stsVcPathIndex 1.3.6.1.4.1.2544.1.12.4.1.48.1.2
This object is his index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

stsVcPathIfIndex 1.3.6.1.4.1.2544.1.12.4.1.48.1.3
This object has the same value as ifIndex for OCn Path. An integer index value used to uniquely identify this OCn Path interface.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

stsVcPathAdminState 1.3.6.1.4.1.2544.1.12.4.1.48.1.4
This object represents the Administrative State of the OCn Path.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

stsVcPathOperationalState 1.3.6.1.4.1.2544.1.12.4.1.48.1.5
This object represents the Operational State of the OCn Path.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

stsVcPathSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.48.1.6
This object represents the Secondary State of the OCn Path.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

stsVcPathLoopbackConfig 1.3.6.1.4.1.2544.1.12.4.1.48.1.7
This object allows to initiate loopbacks on on the OCn Path.
Status: current Access: read-write
OBJECT-TYPE    
  CmLoopbackType  

stsVcPathLoopbackStatus 1.3.6.1.4.1.2544.1.12.4.1.48.1.8
This object provides status of the current loopback on the OCn Path.
Status: current Access: read-only
OBJECT-TYPE    
  CmLoopbackType  

stsVcPathLoopbackTime 1.3.6.1.4.1.2544.1.12.4.1.48.1.9
This object allows to specify time for timed-loopbacks on on the OCn Path.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..300  

stsVcPathInsertingAIS 1.3.6.1.4.1.2544.1.12.4.1.48.1.10
This object allows to insert AIS-P out from OCn Path when it is in maintenance state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

stsVcPathBerExcThreshold 1.3.6.1.4.1.2544.1.12.4.1.48.1.11
This object provide the threshold of B3EXC.
Status: current Access: read-write
OBJECT-TYPE    
  BitErrRate  

stsVcPathBerDegThreshold 1.3.6.1.4.1.2544.1.12.4.1.48.1.12
This object provides the threshold of B3DEG.
Status: current Access: read-write
OBJECT-TYPE    
  BitErrRate  

stsVcPathTrailTraceFormat 1.3.6.1.4.1.2544.1.12.4.1.48.1.13
This object provides the J1 length mode on the OCn Path.
Status: current Access: read-write
OBJECT-TYPE    
  TrailTraceFormat  

stsVcPathRxTrailTrace 1.3.6.1.4.1.2544.1.12.4.1.48.1.14
This object provides the recevied J1 on the OCn Path.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

stsVcPathTxTrailTrace 1.3.6.1.4.1.2544.1.12.4.1.48.1.15
This object provides the transmit J1 on the OCn Path.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

stsVcPathExpectedTrailTrace 1.3.6.1.4.1.2544.1.12.4.1.48.1.16
This object provides the expected J1 on the OCn Path.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

stsVcPathRxSignalLabel 1.3.6.1.4.1.2544.1.12.4.1.48.1.17
This object provides the recevied C2 on the OCn Path.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

stsVcPathTxSignalLabel 1.3.6.1.4.1.2544.1.12.4.1.48.1.18
This object provides the transmit C2 on the OCn Path.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

stsVcPathExpectedSignalLabel 1.3.6.1.4.1.2544.1.12.4.1.48.1.19
This object provides the expected C2 on the OCn Path.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

stsVcPathRowStatus 1.3.6.1.4.1.2544.1.12.4.1.48.1.20
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of stsVcPathRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with stsVcPathRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The stsVcPathRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

stsVcPathLowOrderPathType 1.3.6.1.4.1.2544.1.12.4.1.48.1.21
This object provides the low Order Path Type of the sts vc interface.
Status: current Access: read-write
OBJECT-TYPE    
  TDMPathType  

vtVcPathTable 1.3.6.1.4.1.2544.1.12.4.1.49
A list of entries corresponding to VT1.5/VC12. These represent the lower order path (LOP) entities.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VtVcPathEntry

vtVcPathEntry 1.3.6.1.4.1.2544.1.12.4.1.49.1
A conceptual row in the vtVcPathTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VtVcPathEntry  

vtVcPathParentIfIndex 1.3.6.1.4.1.2544.1.12.4.1.49.1.1
This object is its parent's ifindex.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

vtVcPathIndex 1.3.6.1.4.1.2544.1.12.4.1.49.1.2
This object represents the unique number of the Path within the parent container represented by vtvcPathParentIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vtVcPathIfIndex 1.3.6.1.4.1.2544.1.12.4.1.49.1.3
This object has the same value as ifIndex for OCn VT1.5/VC12. An integer index value used to uniquely identify this OCn VT1.5/VC12 interface.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

vtVcPathAdminState 1.3.6.1.4.1.2544.1.12.4.1.49.1.4
This object represents the Administrative State of the OCn VT1.5/VC12.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

vtVcPathOperationalState 1.3.6.1.4.1.2544.1.12.4.1.49.1.5
This object represents the Operational State of the OCn VT1.5/VC12.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

vtVcPathSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.49.1.6
This object represents the Secondary State of the OCn VT1.5/VC12.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

vtVcPathLoopbackConfig 1.3.6.1.4.1.2544.1.12.4.1.49.1.7
This object allows to initiate loopbacks on on the OCn VT1.5/VC12.
Status: current Access: read-write
OBJECT-TYPE    
  CmLoopbackType  

vtVcPathLoopbackStatus 1.3.6.1.4.1.2544.1.12.4.1.49.1.8
This object provides status of the current loopback on the OCn VT1.5/VC12.
Status: current Access: read-only
OBJECT-TYPE    
  CmLoopbackType  

vtVcPathLoopbackTime 1.3.6.1.4.1.2544.1.12.4.1.49.1.9
This object allows to specify time for timed-loopbacks on on the OCn VT1.5/VC12.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..300  

vtVcPathInsertingAIS 1.3.6.1.4.1.2544.1.12.4.1.49.1.10
This object allows to insert AIS-P out from OCn VT1.5/VC12 when it is in maintenance state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

vtVcPathBerExcThreshold 1.3.6.1.4.1.2544.1.12.4.1.49.1.11
This object provide the threshold of BEREXC.
Status: current Access: read-write
OBJECT-TYPE    
  BitErrRate  

vtVcPathBerDegThreshold 1.3.6.1.4.1.2544.1.12.4.1.49.1.12
This object provides the threshold of BERDEG.
Status: current Access: read-write
OBJECT-TYPE    
  BitErrRate  

vtVcPathTrailTraceFormat 1.3.6.1.4.1.2544.1.12.4.1.49.1.13
This object provides the J2 length mode on the OCn VT1.5/VC12.
Status: current Access: read-only
OBJECT-TYPE    
  TrailTraceFormat  

vtVcPathRxTrailTrace 1.3.6.1.4.1.2544.1.12.4.1.49.1.14
This object provides the recevied J2 on the OCn VT1.5/VC12.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

vtVcPathTxTrailTrace 1.3.6.1.4.1.2544.1.12.4.1.49.1.15
This object provides the transmit J2 on the OCn VT1.5/VC12.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

vtVcPathExpectedTrailTrace 1.3.6.1.4.1.2544.1.12.4.1.49.1.16
This object provides the expected J2 on the OCn VT1.5/VC12.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

vtVcPathRxSignalLabel 1.3.6.1.4.1.2544.1.12.4.1.49.1.17
This object provides the recevied V5 byte(b5-b7) on the OCn VT1.5/VC12.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..7  

vtVcPathTxSignalLabel 1.3.6.1.4.1.2544.1.12.4.1.49.1.18
This object provides the transmit V5 byte(b5-b7) on the OCn VT1.5/VC12.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..7  

vtVcPathExpectedSignalLabel 1.3.6.1.4.1.2544.1.12.4.1.49.1.19
This object provides the expected V5 byte(b5-b7) on the OCn VT1.5/VC12.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..7  

vtVcPathRowStatus 1.3.6.1.4.1.2544.1.12.4.1.49.1.20
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of vtVcPathRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with vtVcPathRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The vtVcPathRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

e1t1Table 1.3.6.1.4.1.2544.1.12.4.1.50
A list of entries corresponding to E1/T1.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    E1T1Entry

e1t1Entry 1.3.6.1.4.1.2544.1.12.4.1.50.1
A conceptual row in the e1t1Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  E1T1Entry  

e1t1ParentIfIndex 1.3.6.1.4.1.2544.1.12.4.1.50.1.1
This object represents the parent (container) object's interface index. In the case when parent of E1T1Entry does not have a InterfaceIndex then the e1t1ParentIfIndex shall have the value of 2147483647, e.g. if parent of E1T1Entry is a card represented in pseudoWireE1T1CardTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

e1t1Index 1.3.6.1.4.1.2544.1.12.4.1.50.1.2
Index value used to uniquely identify this E1/T1 interface, within the parent container specified by e1t1ParentIfIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

e1t1IfIndex 1.3.6.1.4.1.2544.1.12.4.1.50.1.3
This object has the same value as ifIndex for E1/T1. An integer index value used to uniquely identify this E1/T1 interface.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

e1t1EntityIndex 1.3.6.1.4.1.2544.1.12.4.1.50.1.4
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

e1t1AdminState 1.3.6.1.4.1.2544.1.12.4.1.50.1.5
This object represents the Administrative State of the E1/T1.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

e1t1OperationalState 1.3.6.1.4.1.2544.1.12.4.1.50.1.6
This object represents the Operational State of the E1/T1.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

e1t1SecondaryState 1.3.6.1.4.1.2544.1.12.4.1.50.1.7
This object represents the Secondary State of the E1/T1.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

e1t1LoopbackConfig 1.3.6.1.4.1.2544.1.12.4.1.50.1.8
This object allows to initiate loopbacks on on the E1/T1.
Status: current Access: read-write
OBJECT-TYPE    
  CmLoopbackType  

e1t1LoopbackStatus 1.3.6.1.4.1.2544.1.12.4.1.50.1.9
This object provides status of the current loopback on the E1/T1.
Status: current Access: read-only
OBJECT-TYPE    
  CmLoopbackType  

e1t1LoopbackTime 1.3.6.1.4.1.2544.1.12.4.1.50.1.10
This object allows to specify time for timed-loopbacks on on the E1/T1.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..300  

e1t1RemoteLoopbackRequest 1.3.6.1.4.1.2544.1.12.4.1.50.1.11
This object allows to specify to repond the remote loopback request or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

e1t1InsertingAIS 1.3.6.1.4.1.2544.1.12.4.1.50.1.12
This object allows to insert AIS out from E1/T1 when it is in maintenance state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

e1t1RowStatus 1.3.6.1.4.1.2544.1.12.4.1.50.1.13
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of e1t1RowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with e1t1RowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The e1t1RowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

e1t1LineType 1.3.6.1.4.1.2544.1.12.4.1.50.1.14
This object represents the E1/T1 Line Type. Determines whether the E1/T1 interface operates in T1 or E1 mode.
Status: current Access: read-only
OBJECT-TYPE    
  E1T1LineType  

e1t1LineCode 1.3.6.1.4.1.2544.1.12.4.1.50.1.15
This object represents the E1/T1 Port Line Code. When the port is configured for a Line Type of T1, the valid values are t1-b8zs and t1-ami and the default value is t1-b8zs. When the port is configured for a Line Type of E1, the valid values are e1-hdb3 and e1-ami and the default value is e1-hdb3.
Status: current Access: read-write
OBJECT-TYPE    
  E1T1LineCode  

e1t1FrameFormat 1.3.6.1.4.1.2544.1.12.4.1.50.1.16
This object represents the E1/T1 Port Frame Format. When the port is configured for a Line Type of T1, the valid values are t1-sf, t1-esf and t1-unframed and the default value is t1-unframed. When the port is configured for a Line Type of E1, the valid values are e1-unframed, e1-crc4, and e1-dualFrame and the default value is e1-crc4. R5.4CC supports only t1-unframed for T1 Line type.
Status: current Access: read-write
OBJECT-TYPE    
  E1T1FrameFormat  

e1t1LineBuildOut 1.3.6.1.4.1.2544.1.12.4.1.50.1.17
This object represents Line Build Out on E1/T1 port.
Status: current Access: read-write
OBJECT-TYPE    
  LineBuildOut  

e1t1TimingDomain 1.3.6.1.4.1.2544.1.12.4.1.50.1.18
This object represents Timing Domain that the E1/T1 interface uses as timing source. The Timing Domain is a Synchronization Entity represented by an object in the f3SyncTable
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

e1t1RcvSensitivity 1.3.6.1.4.1.2544.1.12.4.1.50.1.19
This object allows configuring the reciever sensitivity based on expected signal strength
Status: current Access: read-write
OBJECT-TYPE    
  E1T1RcvSensitivity  

e1t1IdlePatternProfile 1.3.6.1.4.1.2544.1.12.4.1.50.1.20
This object allows selecting Idle Pattern Profile for the E1/T1 interface. Idle Patter Profile is represented by an object in the f3Pwe3IdlePatternProfileTable
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

e1t1LoopbackProfile 1.3.6.1.4.1.2544.1.12.4.1.50.1.21
This object allows selecting Loopback Profile for the E1/T1 interface. Loopback Profile is represented by an object in the f3Pwe3LoopbackProfileTable
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

e1t1RelatedContainerId 1.3.6.1.4.1.2544.1.12.4.1.50.1.22
This object describes the related container VCG.
Status: current Access: read-only
OBJECT-TYPE    
  VariablePointer  

e3t3Table 1.3.6.1.4.1.2544.1.12.4.1.51
A list of entries corresponding to E3/T3.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    E3T3Entry

e3t3Entry 1.3.6.1.4.1.2544.1.12.4.1.51.1
A conceptual row in the e3t3Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  E3T3Entry  

e3t3ParentIfIndex 1.3.6.1.4.1.2544.1.12.4.1.51.1.1
This object is its parent's ifindex.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

e3t3Index 1.3.6.1.4.1.2544.1.12.4.1.51.1.2
This object is his index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

e3t3IfIndex 1.3.6.1.4.1.2544.1.12.4.1.51.1.3
This object has the same value as ifIndex for E3/T3. An integer index value used to uniquely identify this E3/T3 interface.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

e3t3EntityIndex 1.3.6.1.4.1.2544.1.12.4.1.51.1.4
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

e3t3AdminState 1.3.6.1.4.1.2544.1.12.4.1.51.1.5
This object represents the Administrative State of the E3/T3.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

e3t3OperationalState 1.3.6.1.4.1.2544.1.12.4.1.51.1.6
This object represents the Operational State of the E3/T3.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

e3t3SecondaryState 1.3.6.1.4.1.2544.1.12.4.1.51.1.7
This object represents the Secondary State of the E3/T3.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

e3t3LoopbackConfig 1.3.6.1.4.1.2544.1.12.4.1.51.1.8
This object allows to initiate loopbacks on on the E3/T3.
Status: current Access: read-write
OBJECT-TYPE    
  CmLoopbackType  

e3t3LoopbackStatus 1.3.6.1.4.1.2544.1.12.4.1.51.1.9
This object provides status of the current loopback on the E3/T3.
Status: current Access: read-only
OBJECT-TYPE    
  CmLoopbackType  

e3t3LoopbackTime 1.3.6.1.4.1.2544.1.12.4.1.51.1.10
This object allows to specify time for timed-loopbacks on on the E3/T3.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..300  

e3t3RemoteLoopbackRequest 1.3.6.1.4.1.2544.1.12.4.1.51.1.11
This object allows to specify to repond the remote loopback request or not.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

e3t3InsertingAIS 1.3.6.1.4.1.2544.1.12.4.1.51.1.12
This object allows to insert AIS out from E3/T3 when it is in maintenance state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

e3t3CBitEnable 1.3.6.1.4.1.2544.1.12.4.1.51.1.13
The object provides whether C-Bit Parity is enabled/disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

e3t3T3Channelized 1.3.6.1.4.1.2544.1.12.4.1.51.1.14
The object provides whether the T3 tunnel is channlized with T1.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

e3t3RowStatus 1.3.6.1.4.1.2544.1.12.4.1.51.1.15
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of e3t3RowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with e3t3RowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The e3t3RowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

e3t3FrameFormat 1.3.6.1.4.1.2544.1.12.4.1.51.1.16
This object represents the Frame Format of the E3/T3.
Status: current Access: read-write
OBJECT-TYPE    
  E3T3FrameFormat  

e3t3RelatedContainerId 1.3.6.1.4.1.2544.1.12.4.1.51.1.17
This object describe the related contained VCG.
Status: current Access: read-only
OBJECT-TYPE    
  VariablePointer  

cmEthernetTrafficPortExtTable 1.3.6.1.4.1.2544.1.12.4.1.52
A list of entries corresponding to Ethernet Facilities for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetTrafficPortExtEntry

cmEthernetTrafficPortExtEntry 1.3.6.1.4.1.2544.1.12.4.1.52.1
A conceptual row in the cmEthernetTrafficPortExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetTrafficPortExtEntry  

cmEthernetTrafficPortTDMEncapsulation 1.3.6.1.4.1.2544.1.12.4.1.52.1.1
This object describes the GFP Encapsulation type of the traffic port.
Status: current Access: read-write
OBJECT-TYPE    
  GFPEncapsulationType  

cmEthernetTrafficPortRelatedVCG 1.3.6.1.4.1.2544.1.12.4.1.52.1.2
This object describes the related VCG of the traffic port.
Status: current Access: read-only
OBJECT-TYPE    
  VariablePointer  

f3PulsePerSecondPortTable 1.3.6.1.4.1.2544.1.12.4.1.53
A list of entries corresponding to Pulse Per Second Port Facilities.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    F3PulsePerSecondPortEntry

f3PulsePerSecondPortEntry 1.3.6.1.4.1.2544.1.12.4.1.53.1
A conceptual row in the f3PulsePerSecondPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  F3PulsePerSecondPortEntry  

f3PulsePerSecondPortIndex 1.3.6.1.4.1.2544.1.12.4.1.53.1.1
An integer index value used to uniquely identify this Pulse Per Second Port within the card.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

f3PulsePerSecondPortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.53.1.2
This object has the same value as ifIndex for Pulse Per Second Port. An integer index value used to uniquely identify this Pulse Per Second Port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

f3PulsePerSecondPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.53.1.3
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

f3PulsePerSecondPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.53.1.4
This object represents the Administrative State of the Pulse Per Second Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

f3PulsePerSecondPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.53.1.5
This object represents the Operational State of the Pulse Per Second Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

f3PulsePerSecondPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.53.1.6
This object represents the Secondary State of the Pulse Per Second Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

f3PulsePerSecondPortSquelchControl 1.3.6.1.4.1.2544.1.12.4.1.53.1.7
This object allows to set the Squelch Control for the Pulse Per Second port. The Squelch Control is used to determine the type of squelch control used to squelch the output of the TOD port.
Status: current Access: read-write
OBJECT-TYPE    
  SquelchControl  

f3PulsePerSecondPortSquelchQL 1.3.6.1.4.1.2544.1.12.4.1.53.1.8
This object allows to set the Squelch QL for the Pulse Per Second port. This value is used when f3PulsePerSecondPortSquelchControl is squelch-ql. The Squelch QL is used to determine whether or not to squelch the output of the TOD port. If the system's QL is lower than the Squelch QL, the output is squelched.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

f3PulsePerSecondPortTODSource 1.3.6.1.4.1.2544.1.12.4.1.53.1.9
This object allows to set the Pulse Per Second Source for the Port.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

f3PulsePerSecondPortDirection 1.3.6.1.4.1.2544.1.12.4.1.53.1.10
This object allows specification of the signal type (i.e. input or output).
Status: current Access: read-write
OBJECT-TYPE    
  SignalDirectionType  

f3PulsePerSecondPortInputRate 1.3.6.1.4.1.2544.1.12.4.1.53.1.11
This object allows specification of the PPS Input Rate.
Status: current Access: read-write
OBJECT-TYPE    
  PPSInputRate  

f3PulsePerSecondPortDelayCompensation 1.3.6.1.4.1.2544.1.12.4.1.53.1.12
This object allows specification of the PPS external Delay Compensation in nanoseconds. The valid values are 0 to 96 in 8 nanoseconds steps. Values which are not multiple of 8 will be automatically rounded up to the next multiple of 8.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..90  

f3PulsePerSecondPortClockClass 1.3.6.1.4.1.2544.1.12.4.1.53.1.13
This object specify PPS port clock class.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Unsigned32  

f3PulsePerSecondPortClockAccuracy 1.3.6.1.4.1.2544.1.12.4.1.53.1.14
This object specify PPS port clock accuracy.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Unsigned32  

f3PulsePerSecondPortTimeSource 1.3.6.1.4.1.2544.1.12.4.1.53.1.15
This object specify PPS port time source.
Status: deprecated Access: read-only
OBJECT-TYPE    
  TimeSource  

f3PulsePerSecondPortPhyInterfaceType 1.3.6.1.4.1.2544.1.12.4.1.53.1.16
This object specify PPS physical interface type.
Status: current Access: read-write
OBJECT-TYPE    
  PPSPhyInterfaceType  

f3TimeOfDayPortTable 1.3.6.1.4.1.2544.1.12.4.1.55
A list of entries corresponding to Time Of Day Port Facilities.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    F3TimeOfDayPortEntry

f3TimeOfDayPortEntry 1.3.6.1.4.1.2544.1.12.4.1.55.1
A conceptual row in the f3TimeOfDayPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  F3TimeOfDayPortEntry  

f3TimeOfDayPortIndex 1.3.6.1.4.1.2544.1.12.4.1.55.1.1
An integer index value used to uniquely identify this Time Of Day Port within the card.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

f3TimeOfDayPortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.55.1.2
This object has the same value as ifIndex for Time Of Day Port. An integer index value used to uniquely identify this Time Of Day Port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

f3TimeOfDayPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.55.1.3
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

f3TimeOfDayPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.55.1.4
This object represents the Administrative State of the Time Of Day Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

f3TimeOfDayPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.55.1.5
This object represents the Operational State of the Time Of Day Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

f3TimeOfDayPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.55.1.6
This object represents the Secondary State of the Time Of Day Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

f3TimeOfDayPortSquelchControl 1.3.6.1.4.1.2544.1.12.4.1.55.1.7
This object allows to set the Squelch Control for the Time Of Day port. The Squelch Control is used to determine the type of squelch control used to squelch the output of the TOD port.
Status: current Access: read-write
OBJECT-TYPE    
  SquelchControl  

f3TimeOfDayPortSquelchQL 1.3.6.1.4.1.2544.1.12.4.1.55.1.8
This object allows to set the Squelch QL for the Time Of Day port. This value is used when f3TimeOfDayPortSquelchControl is squelch-ql. The Squelch QL is used to determine whether or not to squelch the output of the TOD port. If the system's QL is lower than the Squelch QL, the output is squelched.
Status: current Access: read-write
OBJECT-TYPE    
  SSMQualityLevel  

f3TimeOfDayPortTODSource 1.3.6.1.4.1.2544.1.12.4.1.55.1.9
This object allows to set the Time Of Day Source for the Port.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmEthernetNetPortExtTable 1.3.6.1.4.1.2544.1.12.4.1.56
A list of entries corresponding to Ethernet Network Port Facilities for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetNetPortExtEntry

cmEthernetNetPortExtEntry 1.3.6.1.4.1.2544.1.12.4.1.56.1
A conceptual row in the cmEthernetNetPortExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetNetPortExtEntry  

cmEthernetNetPortTDMEncapsulation 1.3.6.1.4.1.2544.1.12.4.1.56.1.1
This object describes the GFP Encapsulation type of the TDM network port.
Status: current Access: read-write
OBJECT-TYPE    
  GFPEncapsulationType  

cmEthernetNetPortAssociatedTdmEntity 1.3.6.1.4.1.2544.1.12.4.1.56.1.2
This object describes the associated working path of TDM network port.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmEthernetNetPortInsertingAIS 1.3.6.1.4.1.2544.1.12.4.1.56.1.3
This object allows to insert AIS out from TDM network port when it is in maintenance state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

f3GPSReceiverPortTable 1.3.6.1.4.1.2544.1.12.4.1.57
A list of entries corresponding to the GPS Receiver Port Facilities.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    F3GPSReceiverPortEntry

f3GPSReceiverPortEntry 1.3.6.1.4.1.2544.1.12.4.1.57.1
A conceptual row in the f3GPSReceiverPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  F3GPSReceiverPortEntry  

f3GPSReceiverPortIndex 1.3.6.1.4.1.2544.1.12.4.1.57.1.1
An integer index value used to uniquely identify this GPS Receiver Port within the card.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

f3GPSReceiverPortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.57.1.2
This object has the same value as ifIndex for Time Of Day Port. An integer index value used to uniquely identify this GPS Receiver Port.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

f3GPSReceiverPortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.57.1.3
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

f3GPSReceiverPortAdminState 1.3.6.1.4.1.2544.1.12.4.1.57.1.4
This object represents the Administrative State of the GPS Receiver Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

f3GPSReceiverPortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.57.1.5
This object represents the Operational State of the GPS Receiver Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

f3GPSReceiverPortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.57.1.6
This object represents the Secondary State of the GPS Receiver Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

f3GPSReceiverPortPPSGenCondition 1.3.6.1.4.1.2544.1.12.4.1.57.1.7
This object allows for configuration of the PPS generation condition. PPS is generated when at least one satellite is tracked or when at least three satellites are tracked.
Status: current Access: read-write
OBJECT-TYPE    
  PPSGenCondition  

f3GPSReceiverPortAntennaCableLength 1.3.6.1.4.1.2544.1.12.4.1.57.1.8
This object allows for configuration of the GPS Antenna cable length in meters.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

f3GPSReceiverPortAntennaStatus 1.3.6.1.4.1.2544.1.12.4.1.57.1.9
This object provides the GPS Receiver Port Antenna status.
Status: current Access: read-only
OBJECT-TYPE    
  GPSAntennaStatus  

f3GPSReceiverPortSatellitesUsableFlag 1.3.6.1.4.1.2544.1.12.4.1.57.1.10
This object provides information on whether the satellites are usable. It is set to TRUE, when ephemeris and health data for at least one satellite is available.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

f3GPSReceiverPortNumTrackingSatellites 1.3.6.1.4.1.2544.1.12.4.1.57.1.11
This object provides information on the number of tracking satellites.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

f3GPSReceiverPortSelfSurveyProgress 1.3.6.1.4.1.2544.1.12.4.1.57.1.12
This object provides information on the percentage of fixes collected so far.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

f3GPSReceiverPortPPSGeneratedFlag 1.3.6.1.4.1.2544.1.12.4.1.57.1.13
This object indicates whether there are enough usable satellites to provide accurate PPS output.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

f3GPSReceiverPortGnssSystem 1.3.6.1.4.1.2544.1.12.4.1.57.1.14
This object configure Constellation Type of the GPS Antenna.
Status: current Access: read-write
OBJECT-TYPE    
  ConstellationType  

f3GPSReceiverPortInstallationType 1.3.6.1.4.1.2544.1.12.4.1.57.1.15
This object configure Installation Type of the GPS Antenna.
Status: current Access: read-write
OBJECT-TYPE    
  InstallationType  

f3GPSReceiverPortGnssTOD 1.3.6.1.4.1.2544.1.12.4.1.57.1.16
This object provides the last time was executed.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

f3GPSReceiverPortGnssSystemsBitMap 1.3.6.1.4.1.2544.1.12.4.1.57.1.17
this object configures GNSS constellation types supported by a GNSS Receiver Port
Status: current Access: read-write
OBJECT-TYPE    
  ConstellationTypesBitMap  

f3GPSReceiverPortAlias 1.3.6.1.4.1.2544.1.12.4.1.57.1.18
This object provides an alias to the GPS port
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..64)  

cmPethPsePortExtTable 1.3.6.1.4.1.2544.1.12.4.1.58
A list of entries corresponding to PsePortExtEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmPethPsePortExtEntry

cmPethPsePortExtEntry 1.3.6.1.4.1.2544.1.12.4.1.58.1
A conceptual row in the cmPethPsePortExtEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmPethPsePortExtEntry  

cmPethPsePortExtGroupIndex 1.3.6.1.4.1.2544.1.12.4.1.58.1.1
This object has the same value with the group index in pethPsePortTalbe.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

cmPethPsePortExtIndex 1.3.6.1.4.1.2544.1.12.4.1.58.1.2
This object has the same value with the port index in pethPsePortTalbe.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

cmPethPsePortExtAssociatedPort 1.3.6.1.4.1.2544.1.12.4.1.58.1.3
This object means the oid of associated physical port.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

pethPsePortExtPowerConsumption 1.3.6.1.4.1.2544.1.12.4.1.58.1.4
This object means the power consumption of each port in mWatts.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

pethPsePortExtAvailablePowerLevel 1.3.6.1.4.1.2544.1.12.4.1.58.1.5
This object means the pse port available power level.
Status: current Access: read-write
OBJECT-TYPE    
  PsePowerLevel  

pethMainPseEXTTable 1.3.6.1.4.1.2544.1.12.4.1.59
A list of entries corresponding to PethMainPseEXTEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PethMainPseEXTEntry

pethMainPseEXTEntry 1.3.6.1.4.1.2544.1.12.4.1.59.1
A conceptual row in the pethMainPseEXTEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  PethMainPseEXTEntry  

pethMainPseExtGroupIndex 1.3.6.1.4.1.2544.1.12.4.1.59.1.1
This object has the same value with the group index in pethMainPseEXTTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

pethMainPseExtNonStandardPD 1.3.6.1.4.1.2544.1.12.4.1.59.1.2
disabled: don't support non-standard PD, enabled: support non-standard PD
Status: current Access: read-write
OBJECT-TYPE    
  PSENonStandardPD  

cmMPFlowTable 1.3.6.1.4.1.2544.1.12.4.1.60
A list of entries corresponding to MPFlow.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmMPFlowEntry

cmMPFlowEntry 1.3.6.1.4.1.2544.1.12.4.1.60.1
A conceptual row in the cmMPFlowTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmMPFlowEntry  

cmMPFlowIndex 1.3.6.1.4.1.2544.1.12.4.1.60.1.1
An integer index value used to uniquely identify this MultiPointFlow.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

cmMPFlowCircuitName 1.3.6.1.4.1.2544.1.12.4.1.60.1.2
This object allows SNMP management entities to provide a circuit identifier with the MPFlow.
Status: current Access: read-write
OBJECT-TYPE    
  F3DisplayString  

cmMPFlowAdminState 1.3.6.1.4.1.2544.1.12.4.1.60.1.3
This object represents the Administrative State of the Flow.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

cmMPFlowOperationalState 1.3.6.1.4.1.2544.1.12.4.1.60.1.4
This object represents the Operational State of the Flow.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

cmMPFlowSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.60.1.5
This object represents the Secondary State of the Flow.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

cmMPFlowLearningEnabled 1.3.6.1.4.1.2544.1.12.4.1.60.1.6
DISABLED: The forwarding function of the Flow does not dynamically learn MAC address to flowpoint mapping. ENABLED: The forwarding function of the Flow dynamically learns MAC address to flowpoint mapping based on ingress flowpoing and source MAC address.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmMPFlowAgingTimer 1.3.6.1.4.1.2544.1.12.4.1.60.1.7
MAC Table Entry will be removed from the forwarding table after an inactivity time represented by this entry. Not used in EG-X.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmMPFlowFwdTableSizeProfileID 1.3.6.1.4.1.2544.1.12.4.1.60.1.8
Profile ID for Maximum number of MAC Table Entries for the flow
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmMPFlowtableFullAction 1.3.6.1.4.1.2544.1.12.4.1.60.1.9
Action on ingress frames when the number of MAC Table entires has reached the maximum defined by tableSize. BLOCK: A frame with a Source MAC address not in the MAC Table will be discarded. FORWARD: A frame with a Source MAC address not in the MAC table will not be learned and will be flooded to other flowpoints.
Status: current Access: read-write
OBJECT-TYPE    
  LearningAction  

cmMPFlowStorageType 1.3.6.1.4.1.2544.1.12.4.1.60.1.10
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmMPFlowRowStatus 1.3.6.1.4.1.2544.1.12.4.1.60.1.11
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmMPFlowRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmFlowRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmMPFlowRowStatus object may be modified if the associated instance of this object is equal to active(1). Note that flow creation and deletion is only supported with access port in connection-oriented evpl mode.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmMPFlowLearningConfigAction 1.3.6.1.4.1.2544.1.12.4.1.60.1.12
This objects allows performing user action on Learning Table.
Status: current Access: read-write
OBJECT-TYPE    
  LearningConfigAction  

cmMPFlowFPList 1.3.6.1.4.1.2544.1.12.4.1.60.1.13
This object only used to display trap and Flow point list. Fp will be add in the cmMPFlowMemberTable.
Status: current Access: read-write
OBJECT-TYPE    
  F3DisplayString  

cmMPFlowMemberTable 1.3.6.1.4.1.2544.1.12.4.1.61
A list of entries corresponding to MPFlowMember.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmMPFlowMemberEntry

cmMPFlowMemberEntry 1.3.6.1.4.1.2544.1.12.4.1.61.1
A conceptual row in the cmMPFlowMemberTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmMPFlowMemberEntry  

cmMPFlowMemberFPIndex 1.3.6.1.4.1.2544.1.12.4.1.61.1.1
This object describes the relate Flow point.
Status: current Access: not-accessible
OBJECT-TYPE    
  VariablePointer  

cmMPFlowPointRowStatus 1.3.6.1.4.1.2544.1.12.4.1.61.1.2
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmMPFlowPointRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmFlowRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmMPFlowPointRowStatus object may be modified if the associated instance of this object is equal to active(1). Note that flow creation and deletion is only supported with access port in connection-oriented evpl mode.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmEthernetTrafficPortPcpDEEncTable 1.3.6.1.4.1.2544.1.12.4.1.62
EthernetTraffic Port PCP drop eligibility encoding table. This is applied to a frame that is egressing at the EthernetTraffic port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetTrafficPortPcpDEEncEntry

cmEthernetTrafficPortPcpDEEncEntry 1.3.6.1.4.1.2544.1.12.4.1.62.1
A conceptual row in the ethernetPBPcpDEEncPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetTrafficPortPcpDEEncEntry  

cmEthernetTrafficPortPcpDEEncIndex 1.3.6.1.4.1.2544.1.12.4.1.62.1.1
An integer index value used to uniquely identify a row in the PCP drop eligible encoding table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

cmEthernetTrafficPortPcpDEEncInPriority 1.3.6.1.4.1.2544.1.12.4.1.62.1.2
This object is the input priority that is translated to a drop eligibility priority or a drop ineligibility priority.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmEthernetTrafficPortPcpDEEncDropIneligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.62.1.3
This object is the PCP value that has a priority value with implicit drop ineligibility encoded into it.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmEthernetTrafficPortPcpDEEncDropEligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.62.1.4
This object is the PCP value that has a priority value with implicit drop eligibility encoded into it.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmEthernetTrafficPortPcpDEDecTable 1.3.6.1.4.1.2544.1.12.4.1.63
EthernetTraffic Port PCP drop eligibility decoding table. This is applied to a frame that is ingressing at a port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetTrafficPortPcpDEDecEntry

cmEthernetTrafficPortPcpDEDecEntry 1.3.6.1.4.1.2544.1.12.4.1.63.1
A conceptual row in the ethernetPBPcpDEDecPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetTrafficPortPcpDEDecEntry  

cmEthernetTrafficPortPcpDEDecIndex 1.3.6.1.4.1.2544.1.12.4.1.63.1.1
An integer index value used to uniquely identify a row in the PCP drop eligible decoding table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..8  

cmEthernetTrafficPortPcpDEDecInPriority 1.3.6.1.4.1.2544.1.12.4.1.63.1.2
This object is the input priority that is decoded to get priority and the drop eligibility of a frame.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmEthernetTrafficPortPcpDEDecOutPriority 1.3.6.1.4.1.2544.1.12.4.1.63.1.3
This object is the priority value decoded from a incoming PCP value.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmEthernetTrafficPortPcpDEDecDropEligible 1.3.6.1.4.1.2544.1.12.4.1.63.1.4
This object is the drop eligibility decoded from a incoming PCP value.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortPcpDEPairTable 1.3.6.1.4.1.2544.1.12.4.1.64
EthernetTraffic Port PCP drop eligibility priority pair table. The priority pair is encoded to same drop eligibility and drop ineligibility priority. Depending on the PCP DE Enc/Dec mode there can be upto 3 pairs in the table. There will one pair for 7P1D, two pairs for 6P2D and three pairs for 5P3D.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetTrafficPortPcpDEPairEntry

cmEthernetTrafficPortPcpDEPairEntry 1.3.6.1.4.1.2544.1.12.4.1.64.1
A conceptual row in the cmAccPortPcpDEPairEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetTrafficPortPcpDEPairEntry  

cmEthernetTrafficPortPcpDEPairIndex 1.3.6.1.4.1.2544.1.12.4.1.64.1.1
An integer index value used to uniquely identify a row in the PCP drop eligible priority pair table.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..3  

cmEthernetTrafficPortPcpDEDropIneligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.64.1.2
This object is the drop ineligible priority.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmEthernetTrafficPortPcpDEDropEligiblePrio 1.3.6.1.4.1.2544.1.12.4.1.64.1.3
This object is the drop eligible priority.
Status: current Access: read-write
OBJECT-TYPE    
  VlanPriority  

cmEthernetTrafficPortClbTable 1.3.6.1.4.1.2544.1.12.4.1.65
A list of entries corresponding to Ethernet Traffic Port Cable Length Benchmark.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetTrafficPortClbEntry

cmEthernetTrafficPortClbEntry 1.3.6.1.4.1.2544.1.12.4.1.65.1
A conceptual row in the cmEthernetTrafficPortClbTable. These entries represent Cable Length Benchmarks on the Ethernet Traffic Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetTrafficPortClbEntry  

cmEthernetTrafficPortClbIndex 1.3.6.1.4.1.2544.1.12.4.1.65.1.1
An integer index value used to uniquely identify this Cable Length Benchmark Entry specification.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..5  

cmEthernetTrafficPortClbEnabled 1.3.6.1.4.1.2544.1.12.4.1.65.1.2
This enables specification of Cable Length Benchmark entry.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortClbLength 1.3.6.1.4.1.2544.1.12.4.1.65.1.3
Cable length of Cable Points Entry. The cable length is of the form XXX[.YY] where XX can be any integer value and YY allows precision of 2 decimals after the floating point. Note that .YY is optional.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cmEthernetTrafficPortClbDescr 1.3.6.1.4.1.2544.1.12.4.1.65.1.4
A textual string containing description of cable span.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..256)  

networkElementTMParamsTable 1.3.6.1.4.1.2544.1.12.4.1.66
Entries may be auto discovered, or can be explicitly created by SNMP Manager. Each remotely discovered shelf is represented as a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetworkElementTMParamsEntry

networkElementTMParamsEntry 1.3.6.1.4.1.2544.1.12.4.1.66.1
A conceptual row in the networkElementTMParamsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  NetworkElementTMParamsEntry  

neTMParamsBandwidthProfileMode 1.3.6.1.4.1.2544.1.12.4.1.66.1.1
A Network Element level Bandwidth Profile Mode shall be supported which will indicate if the CIR/EIR is interpreted as Information Rate (IR) or Line Rate (LR). In IR mode BWP is enforced based on number of bytes beginning with DA and ending with FCS as it was received at a port which is called the Service Frame in MEF terminology. In LR mode the BWP is enforced based on the whole frame including IFG, Preamble and SFD.
Status: current Access: read-create
OBJECT-TYPE    
  BandwidthProfileMode  

neTMParamsAgingtime 1.3.6.1.4.1.2544.1.12.4.1.66.1.2
The object describe the system aging time.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cmEthernetAccPortJdsuExtTable 1.3.6.1.4.1.2544.1.12.4.1.67
A list of entries corresponding to Ethernet Access Port Facilities for JDSU configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetAccPortJdsuExtEntry

cmEthernetAccPortJdsuExtEntry 1.3.6.1.4.1.2544.1.12.4.1.67.1
A conceptual row in the cmEthernetAccPortJdsuExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetAccPortJdsuExtEntry  

cmEthernetAccPortJDSUControlFramesSnoopingEnabled 1.3.6.1.4.1.2544.1.12.4.1.67.1.1
Enabled: reaction/response to JDSU in-band loopback requests and hallo requests. Disabled: Not reaction/response to JDSU in-band loopback requests and hallo requests. FPGA shall not filter the JDSU control frames to processor. From enabled to disabled, if there is already a JDSU loopback on the port, release current loopback. JDSU loopback doesn't need port in maintenance state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetAccPortJDSULoopbackVlan 1.3.6.1.4.1.2544.1.12.4.1.67.1.2
Applicable when port in JDSU VLAN loopback.
Status: current Access: read-only
OBJECT-TYPE    
  VlanId  

cmEthernetNetPortJdsuExtTable 1.3.6.1.4.1.2544.1.12.4.1.68
A list of entries corresponding to Ethernet Network Port Facilities for JDSU configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetNetPortJdsuExtEntry

cmEthernetNetPortJdsuExtEntry 1.3.6.1.4.1.2544.1.12.4.1.68.1
A conceptual row in the cmEthernetNetPortJdsuExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetNetPortJdsuExtEntry  

cmEthernetNetPortJDSUControlFramesSnoopingEnabled 1.3.6.1.4.1.2544.1.12.4.1.68.1.1
Enabled: reaction/response to JDSU in-band loopback requests and hallo requests. Disabled: Not reaction/response to JDSU in-band loopback requests and hallo requests. FPGA shall not filter the JDSU control frames to processor. From enabled to disabled, if there is already a JDSU loopback on the port, release current loopback. JDSU loopback doesn't need port in maintenance state.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetNetPortJDSULoopbackVlan 1.3.6.1.4.1.2544.1.12.4.1.68.1.2
Applicable when port in JDSU VLAN loopback.
Status: current Access: read-only
OBJECT-TYPE    
  VlanId  

cmEthernetTrafficPortLpbkTable 1.3.6.1.4.1.2544.1.12.4.1.69
A list of entries corresponding to Vlan loopback on Ethernet Traffic Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmEthernetTrafficPortLpbkEntry

cmEthernetTrafficPortLpbkEntry 1.3.6.1.4.1.2544.1.12.4.1.69.1
A conceptual row in the cmEthernetTrafficPortLpbkTable. These entries represent Vlan loopback on the Ethernet Traffic Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmEthernetTrafficPortLpbkEntry  

cmEthernetTrafficPortLpbkIndex 1.3.6.1.4.1.2544.1.12.4.1.69.1.1
An integer index value used to uniquely identify this vlan loopback entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortLpbkInnerVlanEnabled 1.3.6.1.4.1.2544.1.12.4.1.69.1.2
This object represent the inner vlan whether enabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortLpbkInnerVlanTag 1.3.6.1.4.1.2544.1.12.4.1.69.1.3
This object represent the inner vlanid value and priority value. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cmEthernetTrafficPortLpbkOuterVlanEnabled 1.3.6.1.4.1.2544.1.12.4.1.69.1.4
This object represent the outter vlan whether enabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmEthernetTrafficPortLpbkOuterVlanTag 1.3.6.1.4.1.2544.1.12.4.1.69.1.5
This object represent the outter vlanid value and priority value. The value to be specified should be in the form X-Y where X is the VLAN Id and Y is the VLAN Priority. If Y is specified as a *, all Priorities (0 to 7) are looped back.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cmEthernetTrafficPortLpbkTime 1.3.6.1.4.1.2544.1.12.4.1.69.1.6
This object represent the vlan loopback time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmEthernetTrafficPortLpbkStatus 1.3.6.1.4.1.2544.1.12.4.1.69.1.7
This object represent the vlan loopback status.
Status: current Access: read-only
OBJECT-TYPE    
  CmLoopbackType  

cmEthernetTrafficPortLpbkConfig 1.3.6.1.4.1.2544.1.12.4.1.69.1.8
This object represent the vlan loopback action.
Status: current Access: read-write
OBJECT-TYPE    
  CmLoopbackType  

cmPrioMapV2ProfileTable 1.3.6.1.4.1.2544.1.12.4.1.70
A list of entries corresponding to Ethernet Priority Mappings V2 Profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmPrioMapV2ProfileEntry

cmPrioMapV2ProfileEntry 1.3.6.1.4.1.2544.1.12.4.1.70.1
A conceptual row in the cmPrioMapV2ProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmPrioMapV2ProfileEntry  

cmPrioMapV2ProfileIndex 1.3.6.1.4.1.2544.1.12.4.1.70.1.1
The integer index value describes the profile index.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

cmPrioMapV2ProfileAlias 1.3.6.1.4.1.2544.1.12.4.1.70.1.2
The integer index value describes the profile alias.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

cmPrioMapV2ProfileMapModeType 1.3.6.1.4.1.2544.1.12.4.1.70.1.3
The integer index value describes the profile PriorityMapMode.
Status: current Access: read-write
OBJECT-TYPE    
  PriorityMapMode  

cmPrioMapV2ProfileStorageType 1.3.6.1.4.1.2544.1.12.4.1.70.1.4
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cmPrioMapV2ProfileRowStatus 1.3.6.1.4.1.2544.1.12.4.1.70.1.5
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of cmPrioMapV2ProfileStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with cmPrioMapV2ProfileRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The cmPrioMapV2ProfileRowStatus object may be modified if the associated instance of this object is equal to active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmPrioMapV2ProfileIngressCosPriority 1.3.6.1.4.1.2544.1.12.4.1.70.1.6
This object is used to specify whether the profile uses the inner-tag or the outer-tag in determining the COS (Class of Service).
Status: deprecated Access: read-create
OBJECT-TYPE    
  VlanTagType  

cmPrioMapV2ProfileCosMapModeType 1.3.6.1.4.1.2544.1.12.4.1.70.1.7
This object is used to specify Cos mapping mode type.
Status: current Access: read-write
OBJECT-TYPE    
  CosMappingMode  

cmPrioMapV2ProfileCosMapControl 1.3.6.1.4.1.2544.1.12.4.1.70.1.8
This object is used to control whether has cmPrioMapV2PrioMappingCOSTable in profile.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmPrioMapV2ProfileDefaultCos 1.3.6.1.4.1.2544.1.12.4.1.70.1.9
This object is used to specify the Default COS to be used when the Ingress Priority Mapping function does not match.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmPrioMapV2IngressPrioMappingTable 1.3.6.1.4.1.2544.1.12.4.1.71
A list of entries corresponding to Ethernet Priority Mappings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmPrioMapV2IngressPrioMappingEntry

cmPrioMapV2IngressPrioMappingEntry 1.3.6.1.4.1.2544.1.12.4.1.71.1
A conceptual row in the cmPrioMapV2IngressPrioMappingTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmPrioMapV2IngressPrioMappingEntry  

cmPrioMapV2IngressPrioMappingIndex 1.3.6.1.4.1.2544.1.12.4.1.71.1.1
The integer index value corresponding to a priority value based on the cmPrioMapV2ProfileMode. In case of TOS and 8021P, valid indices are 1 to 8, in case of DSCP, valid indices are 1 to 64.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

cmPrioMapV2IngressPrioMappingInPriority 1.3.6.1.4.1.2544.1.12.4.1.71.1.2
The integer index value corresponding to a priority value based on the cmPrioMapV2ProfileMode. In case of TOS and 8021P, valid indices are 0 to 7, in case of DSCP, valid indices are 0 to 63.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..63  

cmPrioMapV2IngressPrioMappingCOS 1.3.6.1.4.1.2544.1.12.4.1.71.1.3
This allows specification of the COS Priority, i.e. this helps in determining the appropriate COS Policer for the Flow.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmPrioMapV2PrioMappingCOSTable 1.3.6.1.4.1.2544.1.12.4.1.72
A list of entries corresponding to Ethernet Priority Mappings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmPrioMapV2PrioMappingCOSEntry

cmPrioMapV2PrioMappingCOSEntry 1.3.6.1.4.1.2544.1.12.4.1.72.1
A conceptual row in the cmPrioMapV2PrioMappingCOSTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmPrioMapV2PrioMappingCOSEntry  

cmPrioMapV2PrioMappingCOSIndex 1.3.6.1.4.1.2544.1.12.4.1.72.1.1
The index of this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

cmPrioMapV2PrioMappingCOSValue 1.3.6.1.4.1.2544.1.12.4.1.72.1.2
This allows specification of the COS Value, i.e. this helps in determining the appropriate COS Policer for the Flow.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

cmPrioMapV2PrioMappingCOSOuterTagPri 1.3.6.1.4.1.2544.1.12.4.1.72.1.3
This allows specification of the VLAN priority that will replace the outgoing (A2N direction) outer-tag's priority.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmPrioMapV2PrioMappingCOSInnerTagPri 1.3.6.1.4.1.2544.1.12.4.1.72.1.4
This allows specification of the VLAN priority that will replace the outgoing (A2N direction) inner-tag's (i.e. second tag) priority.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmPrioMapV2PrioMappingEncapOuterTagPriority 1.3.6.1.4.1.2544.1.12.4.1.72.1.5
This object allows configuring encapsulation outer tag priority value of ingress cos mapping.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmPrioMapV2PrioMappingEncapInnerTagPriority 1.3.6.1.4.1.2544.1.12.4.1.72.1.6
This object allows configuring encapsulation inner tag priority value of ingress cos mapping.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

cmPrioMapV2PrioMappingEncapOuterDscpValue 1.3.6.1.4.1.2544.1.12.4.1.72.1.7
This object allows configuring encapsulation outer DSCP value of ingress cos mapping.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..63  

cmPrioMapV2PrioMappingDscpValue 1.3.6.1.4.1.2544.1.12.4.1.72.1.8
This object allows configuring DSCP value of ingress cos mapping.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..63  

cmPrioMapV2PrioMappingPriTable 1.3.6.1.4.1.2544.1.12.4.1.73
A list of entries corresponding to Ethernet Priority Mappings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmPrioMapV2PrioMappingPriEntry

cmPrioMapV2PrioMappingPriEntry 1.3.6.1.4.1.2544.1.12.4.1.73.1
A conceptual row in the cmPrioMapV2PrioMappingPriTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmPrioMapV2PrioMappingPriEntry  

cmPrioMapV2PrioMappingPriIndex 1.3.6.1.4.1.2544.1.12.4.1.73.1.1
The integer index value corresponding to a priority value based on the cmPrioMapV2ProfileMode. In case of TOS and 8021P, valid indices are 1 to 8, in case of DSCP, valid indices are 1 to 64.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

cmPrioMapV2PrioMappingPriInPrio 1.3.6.1.4.1.2544.1.12.4.1.73.1.2
The integer index value corresponding to a priority value based on the cmPrioMapV2ProfileMode. In case of TOS and 8021P, valid indices are 0 to 7, in case of DSCP, valid indices are 0 to 63.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmPrioMapV2PrioMappingPriPrioControl 1.3.6.1.4.1.2544.1.12.4.1.73.1.3
This allows specification of whether the priority of incoming X-TAG should be swapped with cmPrioMapV2XTagPriority.
Status: current Access: read-write
OBJECT-TYPE    
  PrioMapControlType  

cmPrioMapV2PrioMappingPriXTagPrio 1.3.6.1.4.1.2544.1.12.4.1.73.1.4
This allows specification of the VLAN priority that will replace the incoming X-TAG's priority. This is applicable with cmPrioMapV2XTagControl as 'swap'.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmPrioMapV2PrioMappingPriCOS 1.3.6.1.4.1.2544.1.12.4.1.73.1.5
This allows specification of the COS Priority, i.e. this helps in determining the appropriate COS Policer for the Flow.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

cmPrioMapV2ProfileAppliedObjTable 1.3.6.1.4.1.2544.1.12.4.1.74
A list of entries corresponding to Ethernet Priority Mappings V2 Profile AppliedObj.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmPrioMapV2ProfileAppliedObjEntry

cmPrioMapV2ProfileAppliedObjEntry 1.3.6.1.4.1.2544.1.12.4.1.74.1
A conceptual row in the cmPrioMapV2ProfileAppliedObjTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmPrioMapV2ProfileAppliedObjEntry  

cmPrioMapV2ProfileAppliedObj 1.3.6.1.4.1.2544.1.12.4.1.74.1.1
The object describe the profile Applied to. It maybe the access port or network port or flow etc.
Status: current Access: read-only
OBJECT-TYPE    
  VariablePointer  

cmAccPortExtTable 1.3.6.1.4.1.2544.1.12.4.1.75
A list of entries corresponding to Access Port for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmAccPortExtEntry

cmAccPortExtEntry 1.3.6.1.4.1.2544.1.12.4.1.75.1
A conceptual row in the cmAccPortExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmAccPortExtEntry  

cmAccPortExtMcastRateLimitEnabled 1.3.6.1.4.1.2544.1.12.4.1.75.1.1
Whether multicast packets need be limited on this port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmAccPortExtMcastRateLimitSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.75.1.2
The rate limiting for multicast packets per port When cmAccPortExtMcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmAccPortExtMcastRateLimitSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.75.1.3
The rate limiting for multicast packets per port When cmAccPortExtMcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmAccPortExtBcastRateLimitEnabled 1.3.6.1.4.1.2544.1.12.4.1.75.1.4
Whether broadcast packets need be limited per port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmAccPortExtBcastRateLimitSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.75.1.5
The rate limiting for broadcast packets per port When cmAccPortExtBcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmAccPortExtBcastRateLimitSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.75.1.6
The rate limiting for broadcast packets per port When cmAccPortExtBcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmAccPortExtCombinedRateLimitEnabled 1.3.6.1.4.1.2544.1.12.4.1.75.1.7
Whether multicast and broadcast packets need be limited per port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmAccPortExtCombinedRateLimitSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.75.1.8
The rate limiting for multicast and broadcast packets per port. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmAccPortExtCombinedRateLimitSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.75.1.9
The rate limiting for multicast and broadcast packets per port. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmAccPortExtRefPrioMapProfile 1.3.6.1.4.1.2544.1.12.4.1.75.1.10
This object allows to set priority map profile.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

cmNetPortExtTable 1.3.6.1.4.1.2544.1.12.4.1.76
A list of entries corresponding to Network Port for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmNetPortExtEntry

cmNetPortExtEntry 1.3.6.1.4.1.2544.1.12.4.1.76.1
A conceptual row in the cmNetPortExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmNetPortExtEntry  

cmNetPortExtMcastRateLimitEnabled 1.3.6.1.4.1.2544.1.12.4.1.76.1.1
Whether multicast packets need be limited on this port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmNetPortExtMcastRateLimitSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.76.1.2
The rate limiting for multicast packets per port When cmNetPortExtMcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmNetPortExtMcastRateLimitSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.76.1.3
The rate limiting for multicast packets per port When cmNetPortExtMcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmNetPortExtBcastRateLimitEnabled 1.3.6.1.4.1.2544.1.12.4.1.76.1.4
Whether broadcast packets need be limited per port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmNetPortExtBcastRateLimitSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.76.1.5
The rate limiting for broadcast packets per port When cmNetPortExtBcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmNetPortExtBcastRateLimitSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.76.1.6
The rate limiting for broadcast packets per port When cmNetPortExtBcastRateLimitEnabled and the value is 0, it means all multicast frame are dropped. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmNetPortExtCombinedRateLimitEnabled 1.3.6.1.4.1.2544.1.12.4.1.76.1.7
Whether multicast and broadcast packets need be limited per port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmNetPortExtCombinedRateLimitSpeedLo 1.3.6.1.4.1.2544.1.12.4.1.76.1.8
The rate limiting for multicast and broadcast packets per port. This objects only represents low 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmNetPortExtCombinedRateLimitSpeedHi 1.3.6.1.4.1.2544.1.12.4.1.76.1.9
The rate limiting for multicast and broadcast packets per port. This objects only represents high 32 bits.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cmNetPortExtRefPrioMapProfile 1.3.6.1.4.1.2544.1.12.4.1.76.1.10
This object allows to set priority map profile.
Status: current Access: read-write
OBJECT-TYPE    
  VariablePointer  

f3UsbWIFIDonglePortTable 1.3.6.1.4.1.2544.1.12.4.1.77
A list of entries corresponding to wifi dongle Port for configuration purposes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    F3UsbWIFIDonglePortEntry

f3UsbWIFIDonglePortEntry 1.3.6.1.4.1.2544.1.12.4.1.77.1
A conceptual row in the f3UsbWIFIDonglePortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  F3UsbWIFIDonglePortEntry  

f3UsbWIFIDonglePortIndex 1.3.6.1.4.1.2544.1.12.4.1.77.1.1
An integer index value used to uniquely identify WIFI dongle port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

f3UsbWIFIDonglePortIfIndex 1.3.6.1.4.1.2544.1.12.4.1.77.1.2
This object has the same value as ifIndex for WIFI dongle Port. An integer index value used to uniquely identify this Port
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

f3UsbWIFIDonglePortEntityIndex 1.3.6.1.4.1.2544.1.12.4.1.77.1.3
Entity Index from ENTITY-MIB for this port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndex  

f3UsbWIFIDonglePortAdminState 1.3.6.1.4.1.2544.1.12.4.1.77.1.4
This object represents the Administrative State of this Port.
Status: current Access: read-write
OBJECT-TYPE    
  AdminState  

f3UsbWIFIDonglePortOperationalState 1.3.6.1.4.1.2544.1.12.4.1.77.1.5
This object represents the Operational State of this Port.
Status: current Access: read-only
OBJECT-TYPE    
  OperationalState  

f3UsbWIFIDonglePortSecondaryState 1.3.6.1.4.1.2544.1.12.4.1.77.1.6
This object represents the Secondary State of this Port.
Status: current Access: read-only
OBJECT-TYPE    
  SecondaryState  

f3UsbWIFIDonglePortSSID 1.3.6.1.4.1.2544.1.12.4.1.77.1.7
This object represents the SSID value of this port.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

f3UsbWIFIDonglePortPassword 1.3.6.1.4.1.2544.1.12.4.1.77.1.8
This object represents the password value of this SSID.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

f3UsbWIFIDonglePortEncryption 1.3.6.1.4.1.2544.1.12.4.1.77.1.9
The encryption type of this port.
Status: current Access: read-write
OBJECT-TYPE    
  WIFIEncryptionType  

f3UsbWIFIDonglePortIPAddress 1.3.6.1.4.1.2544.1.12.4.1.77.1.10
The IP address of this port.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

f3UsbWIFIDonglePortwWIFIIPNetMask 1.3.6.1.4.1.2544.1.12.4.1.77.1.11
The IP address mask of this port.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

f3UsbWIFIDonglePortWIFIDHCPRole 1.3.6.1.4.1.2544.1.12.4.1.77.1.12
The DHCP role type of this port.
Status: current Access: read-only
OBJECT-TYPE    
  DHCPType  

f3UsbWIFIDonglePortWIFIAllocatedIPFrom 1.3.6.1.4.1.2544.1.12.4.1.77.1.13
The start IP address could be allocated.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

f3UsbWIFIDonglePortWIFIAllocatedIPEnd 1.3.6.1.4.1.2544.1.12.4.1.77.1.14
The last IP address could be allocated.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

f3UsbWIFIDonglePortStorageType 1.3.6.1.4.1.2544.1.12.4.1.77.1.15
The type of storage configured for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

f3UsbWIFIDonglePortRowStatus 1.3.6.1.4.1.2544.1.12.4.1.77.1.16
The status of this row. An entry MUST NOT exist in the active state unless all objects in the entry have an appropriate value, as described in the description clause for each writable object. The values of f3UsbWIFIDonglePortRowStatus supported are createAndGo(4) and destroy(6). All mandatory attributes must be specified in a single SNMP SET request with f3UsbWIFIDonglePortRowStatus value as createAndGo(4). Upon successful row creation, this object has a value of active(1). The f3UsbWIFIDonglePortRowStatus object may be modified if the associated instance of this object is equal to active(1). Note that flow creation and deletion is only supported with access port in connection-oriented evpl mode.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

f3UsbWIFIDonglePortAccessdUsers 1.3.6.1.4.1.2544.1.12.4.1.77.1.17
The users list of accessed via WIFI dongle port.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

cmFacilityCompliances 1.3.6.1.4.1.2544.1.12.4.2.1
OBJECT IDENTIFIER    

cmFacilityGroups 1.3.6.1.4.1.2544.1.12.4.2.2
OBJECT IDENTIFIER    

cmFacilityCompliance 1.3.6.1.4.1.2544.1.12.4.2.1.1
Describes the requirements for conformance to the CM Facility group.
Status: current Access: read-only
MODULE-COMPLIANCE    

cmFacilityObjectGroup 1.3.6.1.4.1.2544.1.12.4.2.2.1
*********************THIS GROUP IS NOW DEPRECATED ********************* A collection of objects used to manage the CM Facility group.
Status: deprecated Access: read-only
OBJECT-GROUP    

ethernetAccessPortGroup 1.3.6.1.4.1.2544.1.12.4.2.2.2
A collection of objects used to manage the F3 Ethernet Access Port function.
Status: current Access: read-only
OBJECT-GROUP    

ethernetNetworkPortGroup 1.3.6.1.4.1.2544.1.12.4.2.2.3
A collection of objects used to manage the F3 Ethernet Network Port function.
Status: current Access: read-only
OBJECT-GROUP    

ethernetMgmtPortGroup 1.3.6.1.4.1.2544.1.12.4.2.2.4
A collection of objects used to manage the F3 Ethernet Management Port function.
Status: current Access: read-only
OBJECT-GROUP    

bitsPortGroup 1.3.6.1.4.1.2544.1.12.4.2.2.5
A collection of objects used to manage the F3 Bits Port function.
Status: current Access: read-only
OBJECT-GROUP    

trafficGroup 1.3.6.1.4.1.2544.1.12.4.2.2.6
A collection of objects used to manage the F3 traffic path, consists of Flows, Policers and Shapers.
Status: current Access: read-only
OBJECT-GROUP    

prioMapGroup 1.3.6.1.4.1.2544.1.12.4.2.2.7
A collection of objects used to manage the F3 Priority Mapping function.
Status: current Access: read-only
OBJECT-GROUP    

pcpEncodeGroup 1.3.6.1.4.1.2544.1.12.4.2.2.8
A collection of objects used to manage the F3 Priority Mapping function.
Status: current Access: read-only
OBJECT-GROUP    

cpdV2Group 1.3.6.1.4.1.2544.1.12.4.2.2.9
A collection of objects used to manage the Control Protocol Disposition version 2 function.
Status: current Access: read-only
OBJECT-GROUP    

trafficGroupCmHub 1.3.6.1.4.1.2544.1.12.4.2.2.10
A collection of objects used to manage the F3 traffic path, consists of Flows, Policers and Shapers.
Status: current Access: read-only
OBJECT-GROUP    

ocnStmGroup 1.3.6.1.4.1.2544.1.12.4.2.2.11
A collection of objects used to manage the OCN/STM Line.
Status: current Access: read-only
OBJECT-GROUP    

stsVcPathGroup 1.3.6.1.4.1.2544.1.12.4.2.2.12
A collection of objects used to manage the STS/VC Higher Order Path.
Status: current Access: read-only
OBJECT-GROUP    

vtVcPathGroup 1.3.6.1.4.1.2544.1.12.4.2.2.13
A collection of objects used to manage the VT/VC Lower Order Path.
Status: current Access: read-only
OBJECT-GROUP    

e1t1InterfaceGroup 1.3.6.1.4.1.2544.1.12.4.2.2.14
A collection of objects used to manage the E1/T1 Interface Group.
Status: current Access: read-only
OBJECT-GROUP    

e3t3InterfaceGroup 1.3.6.1.4.1.2544.1.12.4.2.2.15
A collection of objects used to manage the E3/T3 Interface Group.
Status: current Access: read-only
OBJECT-GROUP    

f3PulsePerSecondPortGroup 1.3.6.1.4.1.2544.1.12.4.2.2.16
A collection of objects used to manage the F3 Pulse Per Second Group.
Status: current Access: read-only
OBJECT-GROUP    

f3TimeOfDayPortGroup 1.3.6.1.4.1.2544.1.12.4.2.2.17
A collection of objects used to manage the F3 Time of Day Port Group.
Status: current Access: read-only
OBJECT-GROUP    

f3Gps10MhzPortGroup 1.3.6.1.4.1.2544.1.12.4.2.2.18
A collection of objects used to manage the F3 GPS 10 Mhz Port Group.
Status: current Access: read-only
OBJECT-GROUP    

ethernetNetworkPortExtGroup 1.3.6.1.4.1.2544.1.12.4.2.2.19
A collection of objects used to manage the F3 Ethernet Network Port extense function.
Status: current Access: read-only
OBJECT-GROUP    

f3GPSReceiverPortGroup 1.3.6.1.4.1.2544.1.12.4.2.2.20
A collection of objects used to manage the F3 GPS Receiver Port Group.
Status: current Access: read-only
OBJECT-GROUP    

cmPsePortGroup 1.3.6.1.4.1.2544.1.12.4.2.2.21
A collection of objects used to manage the pse port ext entry Group.
Status: current Access: read-only
OBJECT-GROUP    

cmPseEXTGroup 1.3.6.1.4.1.2544.1.12.4.2.2.22
A collection of objects used to manage the pse group ext entry Group.
Status: current Access: read-only
OBJECT-GROUP    

cmMPFlowGroup 1.3.6.1.4.1.2544.1.12.4.2.2.23
A collection of objects used to manage the MP flow entry Group.
Status: current Access: read-only
OBJECT-GROUP    

cmMPFlowMemberGroup 1.3.6.1.4.1.2544.1.12.4.2.2.24
A collection of objects used to manage the MP flow Member entry Group.
Status: current Access: read-only
OBJECT-GROUP    

cmEthernetTrafficPortPcpGroup 1.3.6.1.4.1.2544.1.12.4.2.2.25
A collection of objects used to manage the traffic port pcp Group.
Status: current Access: read-only
OBJECT-GROUP    

neTMParamsGroup 1.3.6.1.4.1.2544.1.12.4.2.2.26
A collection of objects used to manage the ne facility entry Group.
Status: current Access: read-only
OBJECT-GROUP    

cmEthernetTrafficPortGroup 1.3.6.1.4.1.2544.1.12.4.2.2.27
A collection of objects used to manage the traffic port entry Group.
Status: current Access: read-only
OBJECT-GROUP    

cmFlowPointGroup 1.3.6.1.4.1.2544.1.12.4.2.2.28
A collection of objects used to manage the flow point entry Group.
Status: current Access: read-only
OBJECT-GROUP    

ethernetAccessPortJdsuExtGroup 1.3.6.1.4.1.2544.1.12.4.2.2.29
A collection of objects used to manage the F3 Ethernet Access Port JDSU extense function.
Status: current Access: read-only
OBJECT-GROUP    

ethernetNetworkPortJdsuExtGroup 1.3.6.1.4.1.2544.1.12.4.2.2.30
A collection of objects used to manage the F3 Ethernet Network Port JDSU extense function.
Status: current Access: read-only
OBJECT-GROUP    

cmTrafficPortLpbkGroup 1.3.6.1.4.1.2544.1.12.4.2.2.31
A collection of objects used to manage the traffic port lpbk group.
Status: current Access: read-only
OBJECT-GROUP    

cmPrioMapV2ProfileGroup 1.3.6.1.4.1.2544.1.12.4.2.2.32
A collection of objects used to manage the priority map profile group.
Status: current Access: read-only
OBJECT-GROUP    

cmPrioMapV2IngressPrioMappingGroup 1.3.6.1.4.1.2544.1.12.4.2.2.33
A collection of objects used to manage the priority map group.
Status: current Access: read-only
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor