CISCO-WIRELESS-P2MP-PHY-MIB

File: CISCO-WIRELESS-P2MP-PHY-MIB.mib (56321 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB CISCO-WIRELESS-TC-MIB CISCO-TC
ENTITY-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
NOTIFICATION-TYPE DisplayString TruthValue
MODULE-COMPLIANCE OBJECT-GROUP ifIndex
CwrOscState CwrRfType CwrRfFreqRange
Unsigned32 entPhysicalIndex ciscoMgmt

Defined Types

P2mpRadioPhyEntry  
SEQUENCE    
  p2mpSelfTest TruthValue
  p2mpDiversityAntennaPresent TruthValue
  p2mpCableLoss Unsigned32
  p2mpCableLossDiversity Unsigned32
  p2mpClockRefExt TruthValue
  p2mpDenyService TruthValue
  p2mpCommonTrapEnable TruthValue
  p2mpLastPhyFailureType INTEGER
  p2mpLastPhyFailureReason DisplayString

P2mpRfEntry  
SEQUENCE    
  p2mpRfIndex Integer32
  p2mpRfType CwrRfType
  p2mpRfOpMode INTEGER
  p2mpTxFreqRangeMin CwrRfFreqRange
  p2mpTxFreqRangeMax CwrRfFreqRange
  p2mpRxFreqRangeMin CwrRfFreqRange
  p2mpRxFreqRangeMax CwrRfFreqRange
  p2mpMinTxPower Integer32
  p2mpMaxTxPower Integer32
  p2mpRfTemperature Integer32
  p2mpRfTxOscState CwrOscState
  p2mpRfRxOscState CwrOscState
  p2mpRfSupplyVoltageState INTEGER
  p2mpRfStatus INTEGER
  p2mpRfLoopbackSupported TruthValue

P2mpDuplexerEntry  
SEQUENCE    
  p2mpDuplexerIndex Integer32
  p2mpDuplexerRF CwrRfType
  p2mpDuplexerLoPassbandMinFreq CwrRfFreqRange
  p2mpDuplexerLoPassbandMaxFreq CwrRfFreqRange
  p2mpDuplexerHiPassbandMinFreq CwrRfFreqRange
  p2mpDuplexerHiPassbandMaxFreq CwrRfFreqRange
  p2mpDuplexerReceivePassband INTEGER
  p2mpDuplexerTxInsertionLoss Integer32
  p2mpDuplexerBurnDate DisplayString

P2mpAntennaEntry  
SEQUENCE    
  p2mpAntennaIndex Unsigned32
  p2mpRfResource CwrRfType
  p2mpAntennaXDim Unsigned32
  p2mpAntennaYDim Unsigned32
  p2mpAntennaType DisplayString
  p2mpAntennaDescr DisplayString
  p2mpAntennaGain Unsigned32
  p2mpAntennaPolarization INTEGER

P2mpLoopbackEntry  
SEQUENCE    
  p2mpLocalLoopbackMode INTEGER
  p2mpLocalLoopbackAntenna CwrRfType
  p2mpLocalLoopbackChannel Unsigned32

P2mpLedEntry  
SEQUENCE    
  p2mpLedIndex Integer32
  p2mpLedType INTEGER
  p2mpLedState INTEGER

P2mpSuRadioPhyEntry  
SEQUENCE    
  p2mpSuTxMuteEnable TruthValue
  p2mpSuTxMuteDuration Unsigned32

P2mpSuPowerScanEntry  
SEQUENCE    
  p2mpSuPowerScanIndex Integer32
  p2mpSuCenterFrequency CwrRfFreqRange
  p2mpSuMeasuredPower Integer32

P2mpHeAlcEntry  
SEQUENCE    
  p2mpHeAlcEnable TruthValue
  p2mpHeAlcInterval Unsigned32
  p2mpHeAlcNumMiniSlots Unsigned32

P2mpHeIntFreqEntry  
SEQUENCE    
  p2mpHeIfTxOscState CwrOscState
  p2mpHeIfRxOscState CwrOscState
  p2mpHeIfRefOscState CwrOscState
  p2mpHeIfInpFreq Unsigned32
  p2mpHeIfOutFreq Unsigned32
  p2mpHeTrapEnable TruthValue

Defined Values

ciscoWirelessPhyMIB 1.3.6.1.4.1.9.9.170
This is the MIB Module for the Cisco Wireless Radio Point to MultiPoint interface.
MODULE-IDENTITY    

p2mpRadioObjects 1.3.6.1.4.1.9.9.170.1
OBJECT IDENTIFIER    

p2mpRadioBaseObjects 1.3.6.1.4.1.9.9.170.1.1
OBJECT IDENTIFIER    

p2mpRadioSuObjects 1.3.6.1.4.1.9.9.170.1.2
OBJECT IDENTIFIER    

p2mpRadioHeObjects 1.3.6.1.4.1.9.9.170.1.3
OBJECT IDENTIFIER    

p2mpPhyConfigGroup 1.3.6.1.4.1.9.9.170.1.1.1
OBJECT IDENTIFIER    

p2mpFreqResourceGroup 1.3.6.1.4.1.9.9.170.1.1.2
OBJECT IDENTIFIER    

p2mpRadioTestGroup 1.3.6.1.4.1.9.9.170.1.1.3
OBJECT IDENTIFIER    

p2mpLedGroup 1.3.6.1.4.1.9.9.170.1.1.4
OBJECT IDENTIFIER    

p2mpRadioPhyTable 1.3.6.1.4.1.9.9.170.1.1.1.1
This table provides facilities to configure the physical layer characteristics of the radio link. The objects in this table are supported on the head end and at the subscriber unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    P2mpRadioPhyEntry

p2mpRadioPhyEntry 1.3.6.1.4.1.9.9.170.1.1.1.1.1
The entry of this table is created when the managed system detects a propDocsWirelessMaclayer interface. The entry is removed when the associated propDocsWirelessMaclayer interface is deleted from the ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  P2mpRadioPhyEntry  

p2mpSelfTest 1.3.6.1.4.1.9.9.170.1.1.1.1.1.1
This object is used to enable/disable self test. When set to true(1), the software tests the memory and hardware integrity shortly after the router powers up.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

p2mpDiversityAntennaPresent 1.3.6.1.4.1.9.9.170.1.1.1.1.1.2
When true(1), this object indicates that a diversity antenna is being used to receive the wireless transmissions. When false(2), the radio system is using a single antenna to transmit and receive.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

p2mpCableLoss 1.3.6.1.4.1.9.9.170.1.1.1.1.1.3
This object indicates the measured signal power loss in dB due to the cable connecting the radio to the main antenna. The hardware compensates for this cable loss by adjusting the receive and transmit gain appropriately. A value of 0 indicates no degradation in the signal due to the cable. The radio hardware can compensate for a cable loss of no more than 15 db. This cable loss applies to the main antenna only.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..15  

p2mpCableLossDiversity 1.3.6.1.4.1.9.9.170.1.1.1.1.1.4
This object indicates the measured signal power loss in dB due to the cable connecting the radio to the diversity antenna. The hardware compensates for this loss by adjusting the receive and transmit gain appropriately. A value of 0 indicates no degradation in the signal due to the cable. The radio hardware can compensate for a cable loss of no more than 15 dB. This cable loss applies to the diversity antenna only.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..15  

p2mpDenyService 1.3.6.1.4.1.9.9.170.1.1.1.1.1.5
Indicates if the service is disabled in the unit. For Head-end unit, if this object has the value of 'true', the link is in loopback mode; otherwise the link is enabled for transmitting / receiving data. For Subscriber unit, if this object has the value of 'true', the subscriber unit service is disabled; otherwise, the subscriber unit is enabled for transmitting / receiving data
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

p2mpClockRefExt 1.3.6.1.4.1.9.9.170.1.1.1.1.1.6
This object controls the use of external reference clock for IF module as follows: 'true(1)' - an external reference clock is used 'false(2)' - an internal reference clock is used.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

p2mpCommonTrapEnable 1.3.6.1.4.1.9.9.170.1.1.1.1.1.7
When set to true(1), the notifications common to the head end and subscriber unit are enabled. When set to false(2), these notifications are disabled. The notification controlled by this object are: - p2mpRadioPhyFailNotification - p2mpTrapRfSupplyVoltage - p2mpTrapRfRxOsc - p2mpTrapRfTxOsc - p2mpTrapRfTemp - p2mpTrapRfCommLinkError - p2mpTrapTxPower - p2mpTrapRfStatusChange
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

p2mpLastPhyFailureType 1.3.6.1.4.1.9.9.170.1.1.1.1.1.8
This object indicates the last physical link failure that resulted in a p2mpRadioPhyFailNotification trap. none(1) - no failure p2mpHwConfigUnsupported(2) - The radio subsystem has detected that the configuration requested is not supported by the hardware. The p2mpLastPhyFailureReason variable will indicate which configuration parameter is not supported. p2mpHwConfigMismatch(3) - The radio subsystem has detected that the combination of the configuration parameters requested is inconsistent and cannot be supported. The p2mpLastPhyFailReason variable will indicate the configuration parameter that causes the mismatch. p2mpHwInitFailure(4) - The radio subsystem has failed to initialize the hardware. This implies that there is a critical error condition in the associated hardware. The p2mpLastPhyFailReason specifies the reason why the init failed. p2mpHostIfCommLinkError(5) - The host could not communicate with the IF module. p2mpAutoCableCompFailure(6) - Failed to achieve automatic cable compensation due to loss of Tx signal.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), p2mpHwConfigUnsupported(2), p2mpHwConfigMismatch(3), p2mpHwInitFailure(4), p2mpHostIfCommLinkError(5), p2mpAutoCableCompFailure(6)  

p2mpLastPhyFailureReason 1.3.6.1.4.1.9.9.170.1.1.1.1.1.9
This is a text string that describes the last physical link failure identified by p2mpLastPhyFailureType.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

p2mpRfTable 1.3.6.1.4.1.9.9.170.1.1.2.1
This table contains information about the state of the radio frequency resources used by the radio system. Physically each RF resource may be realized by one antenna and its associated control hardware. A single antenna and its associated electronics may act as more than 1 RF resource. When an RF resource acts as both a transmit and receive resource, the transmit and receive frequency ranges may overlap.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    P2mpRfEntry

p2mpRfEntry 1.3.6.1.4.1.9.9.170.1.1.2.1.1
This represents one entry in the p2mpRfTable. An entry is created in this table when the managed system detects a RF resource. The entry is removed when the RF resource is removed from the wireless system.
Status: current Access: not-accessible
OBJECT-TYPE    
  P2mpRfEntry  

p2mpRfIndex 1.3.6.1.4.1.9.9.170.1.1.2.1.1.1
This object, along with the ifIndex of the MAC layer, represents the index of this entry in the p2mpRfTable. Each entry in the table provides details on the state of the RF resources available in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..100  

p2mpRfType 1.3.6.1.4.1.9.9.170.1.1.2.1.1.2
This object identifies the RF resource.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfType  

p2mpRfOpMode 1.3.6.1.4.1.9.9.170.1.1.2.1.1.3
This object specifies whether this RF resource can either transmit, receive, or do both.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER receiveOnly(1), transmitOnly(2), transmitAndReceive(3)  

p2mpTxFreqRangeMin 1.3.6.1.4.1.9.9.170.1.1.2.1.1.4
This object represents the minimum frequency at which this RF resource can transmit.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfFreqRange  

p2mpTxFreqRangeMax 1.3.6.1.4.1.9.9.170.1.1.2.1.1.5
This object represents the maximum frequency at which this RF resource can transmit.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfFreqRange  

p2mpRxFreqRangeMin 1.3.6.1.4.1.9.9.170.1.1.2.1.1.6
This object represents the lowest transmission frequency this RF resource can receive.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfFreqRange  

p2mpRxFreqRangeMax 1.3.6.1.4.1.9.9.170.1.1.2.1.1.7
This object represents the highest transmission frequency that this RF resource can receive.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfFreqRange  

p2mpMinTxPower 1.3.6.1.4.1.9.9.170.1.1.2.1.1.8
This object represents the minimum power that the RF subsystem can supply the antenna.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -80..50  

p2mpMaxTxPower 1.3.6.1.4.1.9.9.170.1.1.2.1.1.9
This object represents the maximum power that the RF subsystem can supply the antenna.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -80..50  

p2mpRfTemperature 1.3.6.1.4.1.9.9.170.1.1.2.1.1.10
This object represents the current temperature of the RF unit
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -40..100  

p2mpRfTxOscState 1.3.6.1.4.1.9.9.170.1.1.2.1.1.11
This object represents the state of the transmit oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.
Status: current Access: read-only
OBJECT-TYPE    
  CwrOscState  

p2mpRfRxOscState 1.3.6.1.4.1.9.9.170.1.1.2.1.1.12
This object represents the state of the receive oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.
Status: current Access: read-only
OBJECT-TYPE    
  CwrOscState  

p2mpRfSupplyVoltageState 1.3.6.1.4.1.9.9.170.1.1.2.1.1.13
This object specifies whether the voltage supply to the RF unit is within specifications or not. Voltage specifications are hardware dependent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER withinSpecification(1), outsideSpecification(2)  

p2mpRfStatus 1.3.6.1.4.1.9.9.170.1.1.2.1.1.14
This object specifies whether the RF resource is functioning properly. If it is functioning properly then it will be online(1), else offline(2). At the Subscriber Unit, this object will reflect offline(2) if p2mpTxMuteEnable in the p2mpSuRadioPhyTable is true(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER online(1), offline(2)  

p2mpRfLoopbackSupported 1.3.6.1.4.1.9.9.170.1.1.2.1.1.15
This object indicates if the RF unit supports loopback. When true(1), the user can configure loopback using the objects in p2mpLoopbackTable. When false(2), any attempt to configure RF loopback will fail.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

p2mpDuplexerTable 1.3.6.1.4.1.9.9.170.1.1.2.2
This table contains information about the Duplexers available for use on the system. A Duplexer is a mechanical device, that acts as a band pass filter when installed in an RF resource. Normally a RF resource is capable of operating over a wide frequency range. To operate at restricted frequencies, the user has to own that part of the frequency spectrum. Since the user may not own parts of the frequency spectrum over which the RF resource may operate, a duplexer is installed at the RF. This restricts the RF resource to operate in the passband defined by the duplexer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    P2mpDuplexerEntry

p2mpDuplexerEntry 1.3.6.1.4.1.9.9.170.1.1.2.2.1
This represents one entry in the p2mpDuplexerTable. Each entry contains information about the duplexers capabilities and the associated RF resource. An entry is created in this table when the managed system detects a RF resource. The entry is removed when the RF resource is removed from the wireless system.
Status: current Access: not-accessible
OBJECT-TYPE    
  P2mpDuplexerEntry  

p2mpDuplexerIndex 1.3.6.1.4.1.9.9.170.1.1.2.2.1.1
This object, along with ifIndex, uniquely identifies an entry in this table. Each entry contains information about the duplexer's capabilities and also identifies the associated RF resource.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..100  

p2mpDuplexerRF 1.3.6.1.4.1.9.9.170.1.1.2.2.1.2
This object identifies the RF resource associated with this duplexer.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfType  

p2mpDuplexerLoPassbandMinFreq 1.3.6.1.4.1.9.9.170.1.1.2.2.1.3
This object identifies the minimum frequency in the low passband that this duplexer will pass through without attenuation.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfFreqRange  

p2mpDuplexerLoPassbandMaxFreq 1.3.6.1.4.1.9.9.170.1.1.2.2.1.4
This object identifies the maximum frequency in the low passband that this duplexer will pass through without attenuation.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfFreqRange  

p2mpDuplexerHiPassbandMinFreq 1.3.6.1.4.1.9.9.170.1.1.2.2.1.5
This object identifies the minimum frequency in the high passband that this duplexer will pass through without attenuation.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfFreqRange  

p2mpDuplexerHiPassbandMaxFreq 1.3.6.1.4.1.9.9.170.1.1.2.2.1.6
This object identifies the maximum frequency in the high passband that this duplexer will pass through without attenuation.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfFreqRange  

p2mpDuplexerReceivePassband 1.3.6.1.4.1.9.9.170.1.1.2.2.1.7
This object indicates which of the two passbands are being used to receive transmissions. The RF Resource can receive on either of the duplexer passbands. loPassband(1) - The RF Resource is receiving on a frequency in the low passband. hiPassband(2) - The RF Resource is receiving on a frequency in the high passband.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER loPassband(1), hiPassband(2)  

p2mpDuplexerTxInsertionLoss 1.3.6.1.4.1.9.9.170.1.1.2.2.1.8
This object represents the loss in 'dB' that would result in the transmission path due to the duplexer.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

p2mpDuplexerBurnDate 1.3.6.1.4.1.9.9.170.1.1.2.2.1.9
This object indicates the date when the revision information was programmed into non-volatile memory.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

p2mpAntennaTable 1.3.6.1.4.1.9.9.170.1.1.2.3
This table contains information about the antennas available in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    P2mpAntennaEntry

p2mpAntennaEntry 1.3.6.1.4.1.9.9.170.1.1.2.3.1
An entry is created in this table when the managed system detects a RF resource. The entry is removed when the RF resource is removed from the wireless system.
Status: current Access: not-accessible
OBJECT-TYPE    
  P2mpAntennaEntry  

p2mpAntennaIndex 1.3.6.1.4.1.9.9.170.1.1.2.3.1.1
This object, along with ifIndex, represents the index of this entry in the p2mpAntennaTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

p2mpRfResource 1.3.6.1.4.1.9.9.170.1.1.2.3.1.2
This object identifies if the antenna is connected to the main or the diversity RF resource.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfType  

p2mpAntennaXDim 1.3.6.1.4.1.9.9.170.1.1.2.3.1.3
This object represents the dimension of the antenna in the X direction.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..96  

p2mpAntennaYDim 1.3.6.1.4.1.9.9.170.1.1.2.3.1.4
This object represents the dimension of the antenna in the Y direction.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..96  

p2mpAntennaType 1.3.6.1.4.1.9.9.170.1.1.2.3.1.5
This object represents the antenna type. For example, 'dish-antenna'.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

p2mpAntennaDescr 1.3.6.1.4.1.9.9.170.1.1.2.3.1.6
This object is used to describe the antenna. For example, it could be used to identify the manufacturer like in 'Manufactured by Watkins Johnson'.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

p2mpAntennaGain 1.3.6.1.4.1.9.9.170.1.1.2.3.1.7
This object represents the receive and transmit gain of this antenna.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..60  

p2mpAntennaPolarization 1.3.6.1.4.1.9.9.170.1.1.2.3.1.8
This object represents the polarization of the antanna.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER vertical(1), horizontal(2)  

p2mpLoopbackTable 1.3.6.1.4.1.9.9.170.1.1.3.1
This table provides facilities to establish loopback points to exercise various sections of the hardware.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    P2mpLoopbackEntry

p2mpLoopbackEntry 1.3.6.1.4.1.9.9.170.1.1.3.1.1
This represents one entry in the p2mpLoopbackTable. It is created when the managed system detects a propDocsWirelessMaclayer interface. The entry is removed when the associated propDocsWirelessMaclayer interface is deleted from the ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  P2mpLoopbackEntry  

p2mpLocalLoopbackMode 1.3.6.1.4.1.9.9.170.1.1.3.1.1.1
This object is used to configure the system in loopback mode prior to executing some system diagnostic tests. The user selects the point in the system where the data signal should be looped back. The diagnostic tests outlined in the user manual have to be manually executed to determine success or failure. Once all the tests are completed, normal operation is restored by setting this object to noLoopback(1). noLoopback(1) - no loopback fir(2) - loopback at the Finite Impulse Response (FIR) module. if(3) - loopback at the IF module. This exercises the FIR, and IF modules. rf(4) - loopback at the RF unit. This exercises the FIR, IF, and RF modules. This mode is supported only when p2mpRfLoopbackSupported is true(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noLoopback(1), fir(2), if(3), rf(4)  

p2mpLocalLoopbackAntenna 1.3.6.1.4.1.9.9.170.1.1.3.1.1.2
This object identifies the RF resource used for loopback testing. This object is not applicable for loopback testing when p2mpLocalLoopbackMode has a value of 'noLoopback(1)'.
Status: current Access: read-write
OBJECT-TYPE    
  CwrRfType  

p2mpLocalLoopbackChannel 1.3.6.1.4.1.9.9.170.1.1.3.1.1.3
This object identifies the channel being used to loopback the data. This object is not applicable for loopback testing when p2mpLocalLoopbackMode has a value of 'noLoopback(1)'.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..7  

p2mpLedTable 1.3.6.1.4.1.9.9.170.1.1.4.1
Entity (Light emitting diode) LED information. For each LED on the entity, an entry will exist in this table, describing the location and current status of that LED.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    P2mpLedEntry

p2mpLedEntry 1.3.6.1.4.1.9.9.170.1.1.4.1.1
An entry in the table, containing the LED information. The entPhysicalIndex identifies the entity on which the LED's are present.
Status: current Access: not-accessible
OBJECT-TYPE    
  P2mpLedEntry  

p2mpLedIndex 1.3.6.1.4.1.9.9.170.1.1.4.1.1.1
For a given entPhysicalIndex, this index value uniquely identifies an entry in the p2mpLedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..16  

p2mpLedType 1.3.6.1.4.1.9.9.170.1.1.4.1.1.2
Indicates the type or label of the LED.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER interfaceEnable(0), majorAlarm(1), minorAlarm(2), outOfService(3), carrier(4), transmitData(5), receiveData(6)  

p2mpLedState 1.3.6.1.4.1.9.9.170.1.1.4.1.1.3
Indicates the state of the LED.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER off(0), green(1), yellow(2)  

p2mpSuRadioPhyTable 1.3.6.1.4.1.9.9.170.1.2.1
This table contains information about the currently configured physical layer interfaces in the subscriber unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    P2mpSuRadioPhyEntry

p2mpSuRadioPhyEntry 1.3.6.1.4.1.9.9.170.1.2.1.1
An entry containing the radio configuration information of the propDocsWirelessMaclayer interface in the subscriber unit. The entry is created when a propDocsWirelessMaclayer interface is detected in the subscriber unit. The entry is deleted when the associated propDocsWirelessMaclayer interface is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  P2mpSuRadioPhyEntry  

p2mpSuTxMuteEnable 1.3.6.1.4.1.9.9.170.1.2.1.1.1
When true(1), this object indicates the subscriber unit transmission has been turned off for a duration indicated by p2mpSuTxMuteDuration. When false(2), this object indicates that the subscriber unit is transmitting.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

p2mpSuTxMuteDuration 1.3.6.1.4.1.9.9.170.1.2.1.1.2
This object indicates the duration of time (in minutes) for which the subscriber transmission will be turned off.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..65535  

p2mpSuPowerScanTable 1.3.6.1.4.1.9.9.170.1.2.2
This table contains information about the receive power measured at the different possible center frequencies.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    P2mpSuPowerScanEntry

p2mpSuPowerScanEntry 1.3.6.1.4.1.9.9.170.1.2.2.1
An entry containing the power related status information of the propDocsWirelessMaclayer interface in the subscriber unit. The entry is created when a propDocsWirelessMaclayer interface is detected in the subscriber unit. The entry is deleted after the associated propDocsWirelessMaylayer interface is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  P2mpSuPowerScanEntry  

p2mpSuPowerScanIndex 1.3.6.1.4.1.9.9.170.1.2.2.1.1
For a given ifIndex, this index value uniquely identifies an entry in the p2mpSuPowerScanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..20  

p2mpSuCenterFrequency 1.3.6.1.4.1.9.9.170.1.2.2.1.2
This object indicates the frequency at which the receive power at the subscriber unit was measured.
Status: current Access: read-only
OBJECT-TYPE    
  CwrRfFreqRange  

p2mpSuMeasuredPower 1.3.6.1.4.1.9.9.170.1.2.2.1.3
This object represents the power measured at the frequency indicated by p2mpSuCenterFrequency.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -127..50  

p2mpHeAlcTable 1.3.6.1.4.1.9.9.170.1.3.1
This table contains Automatic Line Control (ALC) configuration information. It is supported at the head end only.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    P2mpHeAlcEntry

p2mpHeAlcEntry 1.3.6.1.4.1.9.9.170.1.3.1.1
An entry containing the ALC configuration information the propDocsWirelessMaylayer interface at the head end. The entry is created when a propDocsWirelessMaclayer interface is detected in the head end unit. The entry is deleted after the associated propDocsWirelessMaclayer interface is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  P2mpHeAlcEntry  

p2mpHeAlcEnable 1.3.6.1.4.1.9.9.170.1.3.1.1.1
This object is used to enable/disable ALC at the Head End. A value of true(1), indicates that ALC is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

p2mpHeAlcInterval 1.3.6.1.4.1.9.9.170.1.3.1.1.2
This object represents the scheduling interval. It is the regular interval at which the ALC grant in Map is transmitted to the SU's
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 32..1024  

p2mpHeAlcNumMiniSlots 1.3.6.1.4.1.9.9.170.1.3.1.1.3
This indicates the number of minislots within each grant.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..4  

p2mpHeIntFreqTable 1.3.6.1.4.1.9.9.170.1.3.2
This table contains information about the state of the intermediate frequency subsystem in the radio system. This table is supported at the head end only.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    P2mpHeIntFreqEntry

p2mpHeIntFreqEntry 1.3.6.1.4.1.9.9.170.1.3.2.1
The entry of this table is created when the managed system detects a propDocsWirelessMaclayer interface in the head end unit. The entry is deleted when the associated propDocsWirelessMaclayer interface is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  P2mpHeIntFreqEntry  

p2mpHeIfTxOscState 1.3.6.1.4.1.9.9.170.1.3.2.1.1
This object indicates the state of the IF transmit oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.
Status: current Access: read-only
OBJECT-TYPE    
  CwrOscState  

p2mpHeIfRxOscState 1.3.6.1.4.1.9.9.170.1.3.2.1.2
This object indicates the state of the IF receive oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.
Status: current Access: read-only
OBJECT-TYPE    
  CwrOscState  

p2mpHeIfRefOscState 1.3.6.1.4.1.9.9.170.1.3.2.1.3
This object indicates the state of the IF reference oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.
Status: current Access: read-only
OBJECT-TYPE    
  CwrOscState  

p2mpHeIfInpFreq 1.3.6.1.4.1.9.9.170.1.3.2.1.4
This object represents the IF input frequency.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1000..500000  

p2mpHeIfOutFreq 1.3.6.1.4.1.9.9.170.1.3.2.1.5
This object represents the IF output frequency.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1000..500000  

p2mpHeTrapEnable 1.3.6.1.4.1.9.9.170.1.3.2.1.6
When set to true(1), this enables the notifications that are specific to the head end. When set to false(2), these notifications are disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

p2mpPhyMIBNotificationPrefix 1.3.6.1.4.1.9.9.170.2
OBJECT IDENTIFIER    

p2mpPhyMIBNotification 1.3.6.1.4.1.9.9.170.2.0
OBJECT IDENTIFIER    

p2mpRadioPhyFailNotification 1.3.6.1.4.1.9.9.170.2.0.1
A p2mpRadioPhyFailNotification is sent if the value of p2mpLastPhyFailureType changes due to the new failure being detected in the Radio interface.
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpTrapRfSupplyVoltage 1.3.6.1.4.1.9.9.170.2.0.2
The supply voltage to the RF resource has changed. The p2mpRfSupplyVoltageState specifies whether the supply voltage is in spec or not.
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpTrapRfRxOsc 1.3.6.1.4.1.9.9.170.2.0.3
The RF receive frequency oscillator has changed state. The p2mpRfRxOscState specifies the current state of the oscillator.
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpTrapRfTxOsc 1.3.6.1.4.1.9.9.170.2.0.4
The RF transmit frequency oscillator has changed state. The p2mpRfRxOscState specifies the state of the oscillator.
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpTrapRfTemp 1.3.6.1.4.1.9.9.170.2.0.5
The temperature of the RF module identified by p2mpRfIndex has exceeded a defined reference.
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpTrapRfCommLinkError 1.3.6.1.4.1.9.9.170.2.0.6
This trap indicates that the host and the IF module cannot communicate with the RF resource identified by p2mpRfType.
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpTrapTxPower 1.3.6.1.4.1.9.9.170.2.0.7
This trap indicates that the transmit power for the RF resource identified by p2mpRfType exceeded a predefined threshold.
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpTrapRfStatusChange 1.3.6.1.4.1.9.9.170.2.0.8
This trap indicates that the RF resource either came online(1) or went offline(2).
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpTrapHeIfRxOsc 1.3.6.1.4.1.9.9.170.2.0.9
The IF receive frequency oscillator has changed state.
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpTrapHeIfTxOsc 1.3.6.1.4.1.9.9.170.2.0.10
The IF transmit frequency oscillator has changed state.
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpTrapHeIfExtRefOsc 1.3.6.1.4.1.9.9.170.2.0.11
The IF Reference Frequency oscillator has changed state.
Status: current Access: read-write
NOTIFICATION-TYPE    

p2mpRadioPhyConformance 1.3.6.1.4.1.9.9.170.1.4
OBJECT IDENTIFIER    

p2mpRadioPhyCompliances 1.3.6.1.4.1.9.9.170.1.4.1
OBJECT IDENTIFIER    

p2mpRadioPhyGroups 1.3.6.1.4.1.9.9.170.1.4.2
OBJECT IDENTIFIER    

p2mpRadioPhyCompliance 1.3.6.1.4.1.9.9.170.1.4.1.1
The compliance statement for devices that implement Point to Multipoint wireless interfaces compliant with the Cisco Systems Inc. specification.
Status: current Access: read-write
MODULE-COMPLIANCE    

p2mpCommonRadioGroup 1.3.6.1.4.1.9.9.170.1.4.2.1
Mandatory group of objects implemented to configure a point to multipoint wireless radio.
Status: current Access: read-write
OBJECT-GROUP    

p2mpCommonRfGroup 1.3.6.1.4.1.9.9.170.1.4.2.2
Mandatory group of objects implemented to tune the phy quality in a point to multipoint wireless radio.
Status: current Access: read-write
OBJECT-GROUP    

p2mpCommonTestGroup 1.3.6.1.4.1.9.9.170.1.4.2.3
Mandatory group of objects implemented in the point to multi point wireless system for Testing the link.
Status: current Access: read-write
OBJECT-GROUP    

p2mpRadioSuGroup 1.3.6.1.4.1.9.9.170.1.4.2.5
Group of objects implemented at the Subscriber unit.
Status: current Access: read-write
OBJECT-GROUP    

p2mpRadioHeGroup 1.3.6.1.4.1.9.9.170.1.4.2.6
Group of objects implemented at the Head End.
Status: current Access: read-write
OBJECT-GROUP    

p2mpRadioAntennaGroup 1.3.6.1.4.1.9.9.170.1.4.2.8
Group of objects implemented in the point to multi point wireless system for managing the antennas available in the system.
Status: current Access: read-write
OBJECT-GROUP