CISCO-WAN-FR-X21-MIB

File: CISCO-WAN-FR-X21-MIB.mib (28303 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	BASIS-MIB
CISCOWAN-SMI

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Integer32
MODULE-COMPLIANCE	OBJECT-GROUP	x21
frPortCnfX21PortGrp	ciscoWan

Defined Types

X21CnfGrpEntry
SEQUENCE
	x21LineNum	Integer32
	x21LineEnable	INTEGER
	x21LineType	INTEGER
	x21LineRate	INTEGER
	x21LineLoopbackCommand	INTEGER
	x21LineSendCode	INTEGER
	x21LineLoopbackCodeDetection	INTEGER
	x21ConnectorType	INTEGER
	x21InvertClock	INTEGER
	x21LineInterfaceType	INTEGER
	x21ClkFrequencyThreshold	Integer32
	serialLineRate	Integer32
	serialLineRateVariation	Integer32

FrPortCnfX21PortGrpEntry
SEQUENCE
	x21portNum	Integer32
	x21portLineNum	Integer32
	x21portRowStatus	INTEGER
	x21portFlagsBetweenFrames	Integer32
	x21portEqueueServiceRatio	Integer32
	x21portSpeed	Integer32
	x21portAdmin	INTEGER
	x21portType	INTEGER
	x21portSvcStatus	INTEGER
	x21portSvcInUse	INTEGER
	x21portSvcShareLcn	INTEGER
	x21portSvcLcnLow	Integer32
	x21portSvcLcnHigh	Integer32
	x21portSvcDlciLow	Integer32
	x21portSvcDlciHigh	Integer32
	x21portDeleteSvcs	INTEGER
	x21portIngrSvcBandW	Integer32
	x21portEgrSvcBandW	Integer32

X21AlmCnfGrpEntry
SEQUENCE
	x21AlmCnfLineNum	Integer32
	x21Severity	INTEGER

X21AlmGrpEntry
SEQUENCE
	x21AlmLineNum	Integer32
	x21LineAlarmState	Integer32
	x21LineEIAStatus	Integer32
	x21AlarmClrButton	INTEGER

Defined Values

ciscoWanFrX21MIB		1.3.6.1.4.1.351.150.49
The MIB module to configure X.21/HSSI physical and logical interfaces. This MIB module also contains alarm configuration of X.21 interfaces. Terminologies Used: HSSI : High Speed Serial Interface. The HSSI defines both electrical and physical interfaces on DTE and DCE devices. It operates at the physical layer of the OSI reference model. This provides high-speed data communication over WAN and LAN links.
MODULE-IDENTITY

x21CnfGrp		2.1
OBJECT IDENTIFIER

x21AlmCnfGrp		2.2
OBJECT IDENTIFIER

x21AlmGrp		2.3
OBJECT IDENTIFIER

x21CnfGrpTable		2.1.1
The X21 Configuration table. The table size is given by the value of x21LineNumofValidEntries.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		X21CnfGrpEntry

x21CnfGrpEntry		2.1.1.1
An entry in the X21 Configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	X21CnfGrpEntry

x21LineNum		2.1.1.1.1
This object is the identifier of a X.21 interface. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2. FRSM-HS2B-12IN1 supports a range from 1 to 8.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

x21LineEnable		2.1.1.1.2
This variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify Default is enable.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2), modify(3)

x21LineType		2.1.1.1.3
This variable indicates the type X21 line type. The line-type affects the clock -- the DCE device always provides the clock and DTE accepts it. dteST is only applicable to V.35 interfaces Default is DTE.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dte(1), dce(2), dteST(3)

x21LineRate		2.1.1.1.4
This variable configures the X.21/HSSI/V.35 line-rate. Note that enumerations 51 through 108 are supported only by FRSM-HS2/HS2B card. default is r48Kbps on FRSM-HS2B-12IN1 default is r52Mbps on FRSM-HS2/HS2B-HSSI
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	r48Kbps(1), r56Kbps(2), r64Kbps(3), r112Kbps(4), r128Kbps(5), r168Kbps(6), r192Kbps(7), r224Kbps(8), r256Kbps(9), r280Kbps(10), r320Kbps(11), r336Kbps(12), r384Kbps(13), r392Kbps(14), r448Kbps(15), r512Kbps(16), r768Kbps(17), r1024Kbps(18), r1536Kbps(19), r1544Kbps(20), r1792Kbps(21), r1920Kbps(22), r1984Kbps(23), r2048Kbps(24), r3097Kbps(25), r3157Kbps(26), r4096Kbps(27), r4645Kbps(28), r4736Kbps(29), r6195Kbps(30), r6315Kbps(31), r7744Kbps(32), r7899Kbps(33), r8192Kbps(34), r9289Kbps(35), r9472Kbps(36), r10240Kbps(37), r10890Kbps(38), r11060Kbps(39), r12390Kbps(40), r12630Kbps(41), r13900Kbps(42), r14220Kbps(43), r14340Kbps(44), r15490Kbps(45), r15800Kbps(46), r16380Kbps(47), r20030Kbps(48), r24990Kbps(49), r52Mbps(50), r17370Kbps(51), r18950Kbps(52), r20530Kbps(53), r22100Kbps(54), r23680Kbps(55), r3088Kbps(56), r4632Kbps(57), r6176Kbps(58), r7720Kbps(59), r9264Kbps(60), r10808Kbps(61), r12352Kbps(62), r13896Kbps(63), r15440Kbps(64), r16984Kbps(65), r18528Kbps(66), r20072Kbps(67), r21616Kbps(68), r23160Kbps(69), r24704Kbps(70), r26248Kbps(71), r27792Kbps(72), r29336Kbps(73), r30880Kbps(74), r32424Kbps(75), r33968Kbps(76), r35512Kbps(77), r37056Kbps(78), r38600Kbps(79), r40144Kbps(80), r41688Kbps(81), r43232Kbps(82), r44776Kbps(83), r46320Kbps(84), r47864Kbps(85), r49408Kbps(86), r50952Kbps(87), r6144Kbps(88), r12288Kbps(89), r14336Kbps(90), r16384Kbps(91), r18432Kbps(92), r20480Kbps(93), r22528Kbps(94), r24576Kbps(95), r26624Kbps(96), r28672Kbps(97), r30720Kbps(98), r32768Kbps(99), r34816Kbps(100), r36864Kbps(101), r38912Kbps(102), r40960Kbps(103), r43008Kbps(104), r45056Kbps(105), r47104Kbps(106), r49152Kbps(107), r51200Kbps(108)

x21LineLoopbackCommand		2.1.1.1.5
This variable represents the loopback state x21NoLoop Not in the loopback state. Normal traffic can be sent x21DiagnosticMetallicLoop Loopbacks the line on the back-card towards the Network. x21DiagnosticFrontcardLoop Loopbacks the line on the frontcard toward the Network. x21RemoteLoop The remote NTU is in the loop back mode. In this state, the FRSM-HS1 is sending the loopback code to remote NTU. Default is x21NoLoop. Note: Before going into one of the loopbacks the state should be x21NoLoop.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	x21NoLoop(1), x21DiagnosticMetallicLoop(2), x21DiagnosticFrontcardLoop(3), x21RemoteLoop(4), v35MetallicLoop(5)

x21LineSendCode		2.1.1.1.6
This variable indicates what type of code is being sent across the X.21/HSSI interface by the device. The values mean: x21NoCode: No loopback. x21SendLoopACode: Start sending Loop A code. Valid only if the backcard is HSSI and the line-type is DTE. This command loops the line module of the remote device. x21SendLoopBCode: Start sending Loop B code. Valid only if the backcard is HSSI and the line-type is DTE. This command loops the digital section of the remote device. x21SendLocalLoopCode: Start sending CCITT X.21 Loopback Type 3 code. This is valid only if the backcard is X.21 type. x21SendRemoteLoopCode: Start sending CCITT X.21 Loopback Type 2 code. This is valid only if the backcard is X.21 type. x21SendUnLoopCode: Sending a loopback termination request. Valid for both HSSI and X.21 lines. To execute any of the loop-codes the x21LineLoopbackCommand should be set to x21RemoteLoop. Once the x21SendUnLoopCode succeeds the x21LineLoopbackCommand would transition back to x21NoLoop state. Default is x21NoCode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	x21NoCode(1), x21SendLoopACode(2), x21SendLoopBCode(3), x21SendLocalLoopCode(4), x21SendRemoteLoopCode(5), x21SendUnLoopCode(6)

x21LineLoopbackCodeDetection		2.1.1.1.7
Enable detection of line Loopback Codes. The loopback detection is implemented only in HSSI DCE mode. Default is codeDetectDisabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	codeDetectDisabled(1), codeDetectEnabled(2)

x21ConnectorType		2.1.1.1.8
back card type This object is not used by FRSM-HS2/HS2B
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	x21Backcard(1), hssiBackcard(2), v35Backcard(3)

x21InvertClock		2.1.1.1.9
This object configures two options: a) To invert the clock sent by HS1/HS2B with the TX data or not. b) If DCE,to expect the receive clock looped back from DTE or not. If DTE,to loop back the receive clock from DCE or not. nonInvertedAndNotLooped(1)- a)=dont invert, b)=dont expect rcv clock/ dont loop rcv clock invertedAndNotLooped(2) - a)=invert, b)=dont expect rcv clock/ dont loop rcv clock nonInvertedAndLooped(3) - a)=dont invert, b)=expect rcv clock/ loop rcv clock invertedAndLooped(4) - a)=invert, b)=expect rcv clock/ loop rcv clock Enums 1 and 2 are applicable for X.21/HSSI/V.35 interfaces. Enums 3 and 4 are applicable only for V.35. Default for X.21/HSSI is nonInvertedAndNotLooped(1) Default for V.35 is nonInvertedAndLooped(3) This object is not used by FRSM-HS2/FRSM-HS2B-HSSI This object is used by FRSM-HS2B-12IN1 and default values are nonInvertedAndNotLooped(1) for X.21, nonInvertedAndLooped(3) for V.35.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nonInvertedAndNotLooped(1), invertedAndNotLooped(2), nonInvertedAndLooped(3), invertedAndLooped(4)

x21LineInterfaceType		2.1.1.1.10
This object indicates serial interface type. Default is hssi(1). This object is not is configurable in FRSM-HS2 and FRSM-HS2B-HSSI. It will be set to hssi(1) by default for these cards This object is configurable in FRSM-H2B-12IN1. Default is v35(3).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	hssi(1), x21(2), v35(3)

x21ClkFrequencyThreshold		2.1.1.1.11
This object indicates user configurable percentage of clock frequency, which is used by DTE clock monitoring to declare clock rate out of bound alarm. This object is valid only for X.21/v.35/HSSI DTE interfaces. This object is supported by FRSM-HS2 and FRSM-HS2/B
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..5

serialLineRate		2.1.1.1.12
Line rate for X.21/HSSI/V.35 interfaces in bps. This object is supported only by FRSM-HS2/B card, only multiples of 1000 are accepted. Default is 48Kbps for X.21/V.35 interfaces and 51840Kbps for HSSI interface.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	48000..51840000

serialLineRateVariation		2.1.1.1.13
This object indicates line rate variation of HSSI/X.21/V.35 DCE interfaces in ppm (parts per million). i.e. clock generated from DCE hardware interface = (serialLineRate +/- (serialLineRateVariation * 10^6)/ serialLineRate) This object is supported only by FRSM-HS2/B card
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

x21LineNumofValidEntries		2.1.2
The number of X.21/HSSI configuration entries (regardless of their current configuration) in the x21ConfigTable table.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

frPortCnfX21PortGrpTable		1.3.6.1.4.1.351.110.5.1.1.1.3.1
The config table is for X.21/HSSI logical port interface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		FrPortCnfX21PortGrpEntry

frPortCnfX21PortGrpEntry		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1
An entry for logical port.
Status: current	Access: not-accessible
OBJECT-TYPE
	FrPortCnfX21PortGrpEntry

x21portNum		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.1
This is logical port number. The HSSI backcard can support upto 3 ports. The X.21 back card can support 4 logical ports.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4

x21portLineNum		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.2
This represents the line number. On FRSM-HS1 the HSSI can support 3 lines and X.21 4 lines.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4

x21portRowStatus		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.3
This variable adds, deletes, or modifies the port 1- add 2 - delete 3 - modify Default is add.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	add(1), del(2), mod(3)

x21portFlagsBetweenFrames		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.4
Number of flags transmitted between two consecutive HDLC frames. Default is 1 flag.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10

x21portEqueueServiceRatio		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.5
Number of times queue 1 is serviced for every time queue 2 is serviced. Default is 1.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..15

x21portSpeed		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.6
Port speed in kbps. At present it is same as line speed.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

x21portAdmin		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.7
This object is used for administratively changing the status of the port. Up/down used to up and down the port. Default is the up state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	up(1), down(2), write-Only(3)

x21portType		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.8
This represents port type. The processing of the frames depends on the type of the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	frame-relay(1), frFUNI(2), frame-forward(3)

x21portSvcStatus		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.9
This represents SVC status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

x21portSvcInUse		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.10
This represents port SVC in use.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	not-use(1), in-use(2)

x21portSvcShareLcn		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.11
This represents port type.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	port-based(1), card-based(2)

x21portSvcLcnLow		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.12
This represents low end of reserved LCN for SVC.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	16..271

x21portSvcLcnHigh		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.13
This represents high end of reserved LCN for SVC.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	16..271

x21portSvcDlciLow		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.14
This represents low end of reserved DLCI for SVC.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1023

x21portSvcDlciHigh		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.15
This represents high end of reserved DLCI for SVC.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1023

x21portDeleteSvcs		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.16
Setting this object to 1 indicates that all the SVC connections on the given port has to be deleted.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	delete(1), other(2)

x21portIngrSvcBandW		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.17
This represents Ingress Bandwidth reserve for SVC.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

x21portEgrSvcBandW		1.3.6.1.4.1.351.110.5.1.1.1.3.1.1.18
This represents Egress Bandwidth reserve for SVC.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2147483647

x21AlmCnfGrpTable		2.2.1
The FRSM-HS1/HS2 interface alarm configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		X21AlmCnfGrpEntry

x21AlmCnfGrpEntry		2.2.1.1
An entry in the X.21/HSSI Alarm Configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	X21AlmCnfGrpEntry

x21AlmCnfLineNum		2.2.1.1.1
X.21/HSSI line number. FRSM-HS2/HS2B-HSSI supports a range from 1 to 2. FRSM-HS2B-12IN1 supports a range from 1 to 8.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8

x21Severity		2.2.1.1.2
This variable is used to setup the severity of LOS(Loss of Signal) or clock mismatch alarm. Whenever the above condition arises, the FRSM-HS1/HS2/HS2B will send the alarm with appropriate status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	minor(1), major(2), dontcare(3)

x21AlmGrpTable		2.3.1
The X.21/HSSI interface alarm configuration table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		X21AlmGrpEntry

x21AlmGrpEntry		2.3.1.1
An entry in the X21 Alarm table
Status: current	Access: not-accessible
OBJECT-TYPE
	X21AlmGrpEntry

x21AlmLineNum		2.3.1.1.1
This object is the identifier (line number) of a X.21/HSSI interface. The value for this object must be same as the value of x21LineNum.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

x21LineAlarmState		2.3.1.1.2
This variable is a bitmap of the X21 Line ALarms on the FRSM-HS1. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm ----------- ----- 0 C/I signal is OFF (also used to indicate LOS) 1 Clock rate mismatch (used in DTE mode) 2 Internal Loopback (diagnostic loopback) 3 HSSI Local LoopA (line is in loopback) 4 HSSI Local LoopB (line is in loopback) 5 Remote Loopback (line is transmitting loopcodes) 6 For V35 DTE mode, DCD and CTS both are inactive 7 For V35 DCE mode, RTS is inactive 8 No cable attached to V35 backcard 9 Wrong cable attached to V35 backcard If all the bit-states are 0s: - line is not in alarm, or - line not in loopback, or - line is transmitting any loopback codes.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1023

x21LineEIAStatus		2.3.1.1.3
Indicates the status of X.21/HSSI lines: 0x01 -- c-lead high 0x02 -- i-lead high 0x04 -- LC-lead high (valid only for HSSI DCE mode).
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..10

x21AlarmClrButton		2.3.1.1.4
This variable is used to clear all the alarms for the line. 1 = No action 2 = Clear alarm.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noaction(1), clear(2)

cwfX21MIBConformance		1.3.6.1.4.1.351.150.49.2
OBJECT IDENTIFIER

cwfX21MIBGroups		1.3.6.1.4.1.351.150.49.2.1
OBJECT IDENTIFIER

cwfX21MIBCompliances		1.3.6.1.4.1.351.150.49.2.2
OBJECT IDENTIFIER

cwfX21Compliance		1.3.6.1.4.1.351.150.49.2.2.1
The compliance statement for objects related to Frame Relay Ports.
Status: current	Access: read-write
MODULE-COMPLIANCE

ciscoWanFrX21PortGroup		1.3.6.1.4.1.351.150.49.2.1.1
The collection of objects which are applicable for X21 ports in frame relay.
Status: current	Access: read-write
OBJECT-GROUP

ciscoWanFrX21LineGroup		1.3.6.1.4.1.351.150.49.2.1.2
The collection of objects which are related to x21 lines.
Status: current	Access: read-write
OBJECT-GROUP

ciscoWanFrX21AlarmConfGroup		1.3.6.1.4.1.351.150.49.2.1.3
The collection of objects which are related to x21 lines.
Status: current	Access: read-write
OBJECT-GROUP

ciscoWanFrX21AlarmGroup		1.3.6.1.4.1.351.150.49.2.1.4
The collection of objects which are related to x21 lines.
Status: current	Access: read-write
OBJECT-GROUP