CISCO-WAN-CELL-EXT-MIB

File: CISCO-WAN-CELL-EXT-MIB.mib (48875 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF ENTITY-MIB
IF-MIB SNMPv2-TC SNMP-FRAMEWORK-MIB
INET-ADDRESS-MIB CISCO-WAN-3G-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Integer32 Unsigned32 Counter64
MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP
entPhysicalIndex entPhysicalName ifIndex
RowStatus StorageType TEXTUAL-CONVENTION
SnmpAdminString InetAddressType InetAddress
C3gServiceCapability ciscoMgmt

Defined Types

CiscoWanCellExtProtocolType  
Generic PDN type.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), ipv4(2), ppp(3), ipv6(4), ipv4V6(5)  

CiscoWanCellExtRsrp  
Reference signal received power (RSRP) is defined as the linear average over the power contributions and measured in dBm. The reporting range of RSRP is defined per LTE standard with 1 dBm resolution.
TEXTUAL-CONVENTION    
  Integer32  

CiscoWanCellExtRsrq  
Reference Signal Received Quality (RSRQ) is defined as the ratio NxRSRP over (E-UTRAN carrier RSSI) and measured in dB. The reporting range of RSRQ is defined per LTE standard with 0.5 dB resolution.
TEXTUAL-CONVENTION    
  Integer32  

CiscoWanCellExtCqiIndex  
Channel Quality indicator reported to eNodeB which directly translates to Modulation Coding Scheme selected.
TEXTUAL-CONVENTION    
  Unsigned32  

CiscoWanCellExtSNR  
Signal-to-Noise power Ratio (SNR) is defined as the ratio of signal power to the noise power, measured in dB. It determines the downlink throughput for the UE.
TEXTUAL-CONVENTION    
  Integer32  

CiscoWanCellExtSINR  
Signal to Interference plus Noise Ratio is the power at the receiver due to the required signal, divided by the power due to noise and interference measured in dB. It is used as a measure of signal quality.
TEXTUAL-CONVENTION    
  Integer32  

CwceLteRadioEntry  
SEQUENCE    
  cwceLteCurrRsrp CiscoWanCellExtRsrp
  cwceLteCurrRsrq CiscoWanCellExtRsrq
  cwceLteCurrSnr CiscoWanCellExtSNR
  cwceLteCurrSinr CiscoWanCellExtSINR
  cwceLteCurrCqiIndex CiscoWanCellExtCqiIndex
  cwceLteCurrOperatingBand Unsigned32
  cwceLteNotifRsrp CiscoWanCellExtRsrp
  cwceLteNotifRsrq CiscoWanCellExtRsrq
  cwceLteRsrpOnsetNotifThreshold CiscoWanCellExtRsrp
  cwceLteRsrpAbateNotifThreshold CiscoWanCellExtRsrp
  cwceLteRsrqOnsetNotifThreshold CiscoWanCellExtRsrq
  cwceLteRsrqAbateNotifThreshold CiscoWanCellExtRsrq
  cwceLteRsrpOnsetNotifFlag C3gServiceCapability
  cwceLteRsrpAbateNotifFlag C3gServiceCapability
  cwceLteRsrqOnsetNotifFlag C3gServiceCapability
  cwceLteRsrqAbateNotifFlag C3gServiceCapability

CwceLteRadioHistoryRsrpEntry  
SEQUENCE    
  cwceLteRadioHistoryRsrpPerSecond OCTET STRING
  cwceLteRadioHistoryRsrpPerMinute OCTET STRING
  cwceLteRadioHistoryRsrpPerHour OCTET STRING

CwceLteRadioHistoryRsrqEntry  
SEQUENCE    
  cwceLteRadioHistoryRsrqPerSecond OCTET STRING
  cwceLteRadioHistoryRsrqPerMinute OCTET STRING
  cwceLteRadioHistoryRsrqPerHour OCTET STRING

CwceLteProfileEntry  
SEQUENCE    
  cwceLteProfileIndex Unsigned32
  cwceLteProfileType CiscoWanCellExtProtocolType
  cwceLteProfileIPv4Addr InetAddress
  cwceLteProfileIPv6Addr InetAddress
  cwceLteProfileApn SnmpAdminString
  cwceLteProfileApnAmbr Unsigned32
  cwceLteProfileStorage StorageType
  cwceLteProfileRowStatus RowStatus

CwceLtePdnEntry  
SEQUENCE    
  cwceLtePdnProfileUsed Unsigned32
  cwceLtePdnConnStatus INTEGER
  cwceLtePdnType CiscoWanCellExtProtocolType
  cwceLtePdnIpv4Addr InetAddress
  cwceLtePdnIpv6Addr InetAddress
  cwceLtePdnPriDnsIpv4Addr InetAddress
  cwceLtePdnSecDnsIpv4Addr InetAddress
  cwceLtePdnPriDnsIpv6Addr InetAddress
  cwceLtePdnSecDnsIpv6Addr InetAddress

CwceLteEpsBearerQosEntry  
SEQUENCE    
  cwceLteEpsBearerId Unsigned32
  cwceLteEpsBearerType INTEGER
  cwceLteEpsQCI Unsigned32
  cwceLteEpsArp Unsigned32
  cwceLteEpsBearerResType INTEGER
  cwceLteEpsGbr Unsigned32
  cwceLteEpsMbr Unsigned32
  cwceLteEpsAmbr Unsigned32
  cwceLteEpsTotalBytesTx Counter64
  cwceLteEpsTotalBytesRx Counter64
  cwceLteEpsPacketsTx Counter64
  cwceLteEpsPacketsRx Counter64

Defined Values

ciscoWanCellExtMIB 1.3.6.1.4.1.9.9.817
This MIB module is an extension of CISCO-WAN-3G-MIB.my, and it provides network management support for Cisco cellular WAN 4G/LTE products. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** AMBR - Aggregate Maximum Bit Rate APN - Access Point Name ARP - Allocation and Retention Priority CQI - Channel Quality Indicator eNodeB - Evolved Node B EPS - Evolved Packet System E-UTRAN - Evolved Universal Terrestrial Radio Access GBR - Guaranteed Bit Rate LTE - Long Term Evolution MBR - Maximum Bit Rate PCRF - Policy and Charging Rules Function PDN - Packet Data Network QCI - QoS Class Identifier QOS - Quality of Service RF - Radio Frequency RSRP - Reference Signal Receive Power RSRQ - Reference Signal Receive Quality SINR - Signal-to-Interference plus Noise Ratio SNR - Signal-to-Noise Ratio UE - User Equipment
MODULE-IDENTITY    

ciscoWanCellExtMIBNotifs 1.3.6.1.4.1.9.9.817.0
OBJECT IDENTIFIER    

ciscoWanCellExtMIBObjects 1.3.6.1.4.1.9.9.817.1
OBJECT IDENTIFIER    

ciscoWanCellExtMIBConform 1.3.6.1.4.1.9.9.817.2
OBJECT IDENTIFIER    

ciscoWanCellExtLte 1.3.6.1.4.1.9.9.817.1.1
OBJECT IDENTIFIER    

cwceLteRadio 1.3.6.1.4.1.9.9.817.1.1.1
OBJECT IDENTIFIER    

cwceLteProfile 1.3.6.1.4.1.9.9.817.1.1.2
OBJECT IDENTIFIER    

cwceLteRadioTable 1.3.6.1.4.1.9.9.817.1.1.1.1
This table contains entPhysicalTable entries which are capable of providing operational Cellular 4G/LTE Radio signal parameters and administrative notification information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwceLteRadioEntry

cwceLteRadioEntry 1.3.6.1.4.1.9.9.817.1.1.1.1.1
An entry contains management information of Cellular 4G/LTE Radio signal parameters and notification information. An entry of this table is created if an entity capable of providing operational Cellular 4G/LTE Radio signal parameters and administrative notification information is detected by the agent. An entry of this table is deleted by the agent if the corresponding entry in entPhysicalTable is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  CwceLteRadioEntry  

cwceLteCurrRsrp 1.3.6.1.4.1.9.9.817.1.1.1.1.1.1
This object indicates the LTE RSRP value reported by the modem.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoWanCellExtRsrp  

cwceLteCurrRsrq 1.3.6.1.4.1.9.9.817.1.1.1.1.1.2
This object indicates the LTE RSRQ value reported by the modem.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoWanCellExtRsrq  

cwceLteCurrSnr 1.3.6.1.4.1.9.9.817.1.1.1.1.1.3
This object indicates the LTE SNR value reported by the modem.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoWanCellExtSNR  

cwceLteCurrSinr 1.3.6.1.4.1.9.9.817.1.1.1.1.1.4
This object indicates the LTE SINR value measured in decibels (dB) reported by the modem.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoWanCellExtSINR  

cwceLteCurrCqiIndex 1.3.6.1.4.1.9.9.817.1.1.1.1.1.5
This object indicates he LTE CQI Index reported by the modem.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoWanCellExtCqiIndex  

cwceLteCurrOperatingBand 1.3.6.1.4.1.9.9.817.1.1.1.1.1.6
This object indicates the E-UTRAN Operating Band reported by the modem.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cwceLteNotifRsrp 1.3.6.1.4.1.9.9.817.1.1.1.1.1.7
This object indicates the LTE RSRP value reported by the modem which triggered the most recent cwceLteRsrpOnsetNotif or cwceLteRsrpAbateNotif notification.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoWanCellExtRsrp  

cwceLteNotifRsrq 1.3.6.1.4.1.9.9.817.1.1.1.1.1.8
This object indicates the LTE RSRP value reported by the modem which triggered the most recent cwceLteRsrqOnsetNotif or cwceLteRsrqAbateNotif notification.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoWanCellExtRsrq  

cwceLteRsrpOnsetNotifThreshold 1.3.6.1.4.1.9.9.817.1.1.1.1.1.9
This object specifies the RSRP onset threshold value. If the value of cwceLteCurrRsrp goes below the threshold and the service bit in cwceLteRsrpOnsetNotifFlag is set, the cwceLteRsrqOnsetNotif notification for that service will be sent. The absolute value of cwceLteRsrpAbateNotifThreshold should be less than or equal to the absolute value of cwceLteRsrpOnsetNotifThreshold (|cwceLteRsrpAbateNotifThreshold| <= |cwceLteRsrpOnsetNotifThreshold|).
Status: current Access: read-write
OBJECT-TYPE    
  CiscoWanCellExtRsrp  

cwceLteRsrpAbateNotifThreshold 1.3.6.1.4.1.9.9.817.1.1.1.1.1.10
This object specifies the RSRP abate threshold value. If the value of cwceLteCurrRsrp goes above the threshold and the service bit in cwceLteRsrpOnsetNotifFlag is set, the cwceLteRsrpAbateNotif notification for that service will be sent. The absolute value of cwceLteRsrpAbateNotifThreshold should be less than or equal to the absolute value of cwceLteRsrpOnsetNotifThreshold (|cwceLteRsrpAbateNotifThreshold| <= |cwceLteRsrpOnsetNotifThreshold|).
Status: current Access: read-write
OBJECT-TYPE    
  CiscoWanCellExtRsrp  

cwceLteRsrqOnsetNotifThreshold 1.3.6.1.4.1.9.9.817.1.1.1.1.1.11
This object specifies the RSRQ onset threshold value. If the value of cwceLteCurrRsrq goes below the threshold and the service bit in cwceLteRsrqOnsetNotifFlag is set, the cwceLteRsrqOnsetNotif notification for that service will be sent. The absolute value of cwceLteRsrqAbateNotifThreshold should be less than or equal to the absolute value of cwceLteRsrqOnsetNotifThreshold (|cwceLteRsrqAbateNotifThreshold| <= |cwceLteRsrqOnsetNotifThreshold|).
Status: current Access: read-write
OBJECT-TYPE    
  CiscoWanCellExtRsrq  

cwceLteRsrqAbateNotifThreshold 1.3.6.1.4.1.9.9.817.1.1.1.1.1.12
This object specifies the RSRQ abate threshold value. If the value of cwceLteCurrRsrq goes above the threshold and the service bit in cwceLteRsrqOnsetNotifFlag is set, the cwceLteRsrqAbateNotif notification for that service will be sent. The absolute value of cwceLteRsrqAbateNotifThreshold should be less than or equal to the absolute value of cwceLteRsrqOnsetNotifThreshold (|cwceLteRsrqAbateNotifThreshold| <= |cwceLteRsrqOnsetNotifThreshold|).
Status: current Access: read-write
OBJECT-TYPE    
  CiscoWanCellExtRsrq  

cwceLteRsrpOnsetNotifFlag 1.3.6.1.4.1.9.9.817.1.1.1.1.1.13
This object specifies the flag bitmap to control the generation of notification cwceLteRsrpOnsetNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification cwceLteRsrpOnsetNotif for that service. The default value of this object is all bits are 0. Notifications are not generated in technology modes where RSRP is not relevant.
Status: current Access: read-write
OBJECT-TYPE    
  C3gServiceCapability  

cwceLteRsrpAbateNotifFlag 1.3.6.1.4.1.9.9.817.1.1.1.1.1.14
This object specifies the flag bitmap to control the generation of notification cwceLteRsrpAbateNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification cwceLteRsrpAbateNotif for that service. The default value of this object is all bits are 0. Notifications are not generated in technology modes where RSRP is not relevant.
Status: current Access: read-write
OBJECT-TYPE    
  C3gServiceCapability  

cwceLteRsrqOnsetNotifFlag 1.3.6.1.4.1.9.9.817.1.1.1.1.1.15
This object specifies the flag bitmap to control the generation of notification cwceLteRsrqOnsetNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification cwceLteRsrqOnsetNotif for that service. The default value of this object is all bits are 0. Notifications are not generated in technology modes where RSRQ is not relevant.
Status: current Access: read-write
OBJECT-TYPE    
  C3gServiceCapability  

cwceLteRsrqAbateNotifFlag 1.3.6.1.4.1.9.9.817.1.1.1.1.1.16
This object specifies the flag bitmap to control the generation of notification cwceLteRsrqAbateNotif. Each bit represents a service as defined in C3gServiceCapability, set the bit value to 1 to enable (and 0 to disable) the generation of notification cwceLteRsrqAbateNotif for that service. The default value of this object is all bits are 0. Notifications are not generated in technology modes where RSRQ is not relevant.
Status: current Access: read-write
OBJECT-TYPE    
  C3gServiceCapability  

cwceLteRadioHistory 1.3.6.1.4.1.9.9.817.1.1.1.2
OBJECT IDENTIFIER    

cwceLteRadioHistoryRsrpTable 1.3.6.1.4.1.9.9.817.1.1.1.2.1
This table contains Cellular 4G/LTE RSRP history. The history of RSRP are carried in an octet of string. Each octet in the octet string has a value from 40 to 140 and the 150 value is reserved to indicate an uninitialized (Invalid) value. The format of the octet string with n octets is as following: [ octet 0 is latest, octet 1 is latest-1, . . octet n-2 is oldest-1, octet n-1 is oldest ] To convert the provided value into dBm the following formula should be used: dBm = (-1)*value
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwceLteRadioHistoryRsrpEntry

cwceLteRadioHistoryRsrpEntry 1.3.6.1.4.1.9.9.817.1.1.1.2.1.1
An entry contains management information of Cellular 4G/LTE RSRP Radio history parameters. An entry of this table is created if an entity capable of providing operational Cellular 4G/LTE RSRP Radio history is detected by the agent. An entry of this table is deleted by the agent if the corresponding entry in entPhysicalTable is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  CwceLteRadioHistoryRsrpEntry  

cwceLteRadioHistoryRsrpPerSecond 1.3.6.1.4.1.9.9.817.1.1.1.2.1.1.1
This object indicates per-second RSRP history. It contains a per-second history of RSRP values for the last 60 seconds.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(60)  

cwceLteRadioHistoryRsrpPerMinute 1.3.6.1.4.1.9.9.817.1.1.1.2.1.1.2
This object indicates per-minute weakest RSRP value history. It contains a per-minute history of weakest RSRP values for the last 60 minutes. The octet in the string is the weakest RSRP value measured in a minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(60)  

cwceLteRadioHistoryRsrpPerHour 1.3.6.1.4.1.9.9.817.1.1.1.2.1.1.3
This object indicates per-hour weakest RSRP value history. It contains a per-hour history of weakest RSRP values for the last 72 hours. The octet in the string is the weakest RSRP value measured in an hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(72)  

cwceLteRadioHistoryRsrqTable 1.3.6.1.4.1.9.9.817.1.1.1.2.2
This table contains Cellular 4G/LTE RSRQ history. The history of RSRQ are carried in an octet of string. Each octet in the octet string has a value from 3 to 20 and the 25 value is reserved to indicate an uninitialized (Invalid) value. The format of the octet string with n octets is as following: [ octet 0 is latest, octet 1 is latest-1, . . octet n-2 is oldest-1, octet n-1 is oldest ] To convert the provided value into dB the following formula should be used: dB = (-1)*value
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwceLteRadioHistoryRsrqEntry

cwceLteRadioHistoryRsrqEntry 1.3.6.1.4.1.9.9.817.1.1.1.2.2.1
An entry contains management information of Cellular 4G/LTE RSRQ Radio history parameters. An entry of this table is created if an entity capable of providing operational Cellular 4G/LTE RSRQ Radio history is detected by the agent. An entry of this table is deleted by the agent if the corresponding entry in entPhysicalTable is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  CwceLteRadioHistoryRsrqEntry  

cwceLteRadioHistoryRsrqPerSecond 1.3.6.1.4.1.9.9.817.1.1.1.2.2.1.1
This object indicates per-second RSRQ history. It contains a per-second history of RSRQ values for the last 60 seconds.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(60)  

cwceLteRadioHistoryRsrqPerMinute 1.3.6.1.4.1.9.9.817.1.1.1.2.2.1.2
This object indicates per-minute weakest RSRQ value history. It contains a per-minute history of weakest RSRQ values for the last 60 minutes. The octet in the string is the weakest RSRQ value measured in a minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(60)  

cwceLteRadioHistoryRsrqPerHour 1.3.6.1.4.1.9.9.817.1.1.1.2.2.1.3
This object indicates per-hour weakest RSRQ value history. It contains a per-hour history of weakest RSRQ values for the last 72 hours. The octet in the string is the weakest RSRQ value measured in an hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(72)  

cwceLteIpv4AddrType 1.3.6.1.4.1.9.9.817.1.1.2.1
The object indicates the type of Internet address for IPv4 addresses used by profiles and PDNs. The valid value for this object is ipv4(1).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

cwceLteIpv6AddrType 1.3.6.1.4.1.9.9.817.1.1.2.2
The object indicates the type of Internet address for IPv6 addresses used by profiles and PDNs. The valid value for this object is ipv6(2).
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

cwceLteProfileTable 1.3.6.1.4.1.9.9.817.1.1.2.3
This table contains Cellular LTE PDN profiles. Cellular device contains multiple profile entries which can be used to establish cellular data connections (PDN contexts). Users can choose any of available PDN profiles to establish data connections. Data connections are described in cwcePacketLteSessionTable. This table is valid only in 4G/LTE Technology mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwceLteProfileEntry

cwceLteProfileEntry 1.3.6.1.4.1.9.9.817.1.1.2.3.1
An entry contains management information of Cellular 4G/LTE profile parameters. Entries in this table can be created or deleted using cwceLteProfileRowStatus object. An entry of this table is deleted by the agent if the corresponding entry in entPhysicalTable is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  CwceLteProfileEntry  

cwceLteProfileIndex 1.3.6.1.4.1.9.9.817.1.1.2.3.1.1
This object specifies profile index, combined with entPhysicalIndex to access profile table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cwceLteProfileType 1.3.6.1.4.1.9.9.817.1.1.2.3.1.2
This object specifies the configured EPS Bearer type.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoWanCellExtProtocolType  

cwceLteProfileIPv4Addr 1.3.6.1.4.1.9.9.817.1.1.2.3.1.3
This object specifies the configured EPS Bearer IPv4 address. The type of this address is determined by the value of the cwceLteIpv4AddrType object. This object is valid only if the corresponding instance value of cwceLteProfileType is either 'ipv4' or 'ipv4V6'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

cwceLteProfileIPv6Addr 1.3.6.1.4.1.9.9.817.1.1.2.3.1.4
This object specifies the configured EPS Bearer IPv6 address. The type of this address is determined by the value of the cwceLteIpv6AddrType object. This object is valid only if the corresponding instance value of cwceLteProfileType is either 'ipv6' or 'ipv4V6'.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

cwceLteProfileApn 1.3.6.1.4.1.9.9.817.1.1.2.3.1.5
This object specifies configured profile of Access Point Name (APN). The value of this object should be provided by the APN service provider.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cwceLteProfileApnAmbr 1.3.6.1.4.1.9.9.817.1.1.2.3.1.6
This object specifies the profile APN-AMBR. APN-AMBR is aggregate bit rate across all Non-GBR bearers and across all PDN connections of the same APN. The value APN-AMBR is a parameter which is defined as part of a user's subscription, but may be overridden by the PCRF.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cwceLteProfileStorage 1.3.6.1.4.1.9.9.817.1.1.2.3.1.7
This object specifies the storage type for this conceptual row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cwceLteProfileRowStatus 1.3.6.1.4.1.9.9.817.1.1.2.3.1.8
This object specifies the status of the conceptual row. It's used to manage creation, modification and deletion of rows in this table. When a row is active, user cannot modify the value of the objects in that row. All objects in this row need to have valid value before the row can be active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cwceLtePdnTable 1.3.6.1.4.1.9.9.817.1.1.2.4
This table contains Cellular 4G/LTE Packet Data Network(PDN) information of all the PDN capable interfaces in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwceLtePdnEntry

cwceLtePdnEntry 1.3.6.1.4.1.9.9.817.1.1.2.4.1
An entry contains management information of Cellular 4G/LTE PDN parameters. An entry of this table is created if an interface capable of providing operational Cellular 4G/LTE PDN parameters is detected by the agent. An entry of this table is deleted by the agent if the corresponding entry in ifTable is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  CwceLtePdnEntry  

cwceLtePdnProfileUsed 1.3.6.1.4.1.9.9.817.1.1.2.4.1.2
This object indicates the cwceLteProfileIndex of the profile used by current EPS bearer to establish data connection.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cwceLtePdnConnStatus 1.3.6.1.4.1.9.9.817.1.1.2.4.1.3
This object indicates PDN session status of the profile. This is active when the call is established and PDN context has become active.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), active(2), inactive(3)  

cwceLtePdnType 1.3.6.1.4.1.9.9.817.1.1.2.4.1.4
This object indicates current session PDN type.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoWanCellExtProtocolType  

cwceLtePdnIpv4Addr 1.3.6.1.4.1.9.9.817.1.1.2.4.1.5
This object indicates current session EPS Bearer IPv4 address. The type of this address is determined by the value of the cwceLteIpv4AddrType object.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cwceLtePdnIpv6Addr 1.3.6.1.4.1.9.9.817.1.1.2.4.1.6
This object indicates current session EPS Bearer IPv6 address. The type of this address is determined by the value of the cwceLteIpv6AddrType object.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cwceLtePdnPriDnsIpv4Addr 1.3.6.1.4.1.9.9.817.1.1.2.4.1.7
This object indicates current session EPS Bearer Primary DNS IPv4 address. The type of this address is determined by the value of the cwceLteIpv4AddrType object.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cwceLtePdnSecDnsIpv4Addr 1.3.6.1.4.1.9.9.817.1.1.2.4.1.8
This object indicates current session EPS Bearer Secondary DNS IPv4 address. The type of this address is determined by the value of the cwceLteIpv4AddrType object.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cwceLtePdnPriDnsIpv6Addr 1.3.6.1.4.1.9.9.817.1.1.2.4.1.9
This object indicates current session EPS Bearer Primary DNS IPv6 address. The type of this address is determined by the value of the cwceLteIpv6AddrType object.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cwceLtePdnSecDnsIpv6Addr 1.3.6.1.4.1.9.9.817.1.1.2.4.1.10
This object indicates current session EPS Bearer Secondary DNS IPv6 address. The type of this address is determined by the value of the cwceLteIpv6AddrType object.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cwceLteEpsBearerQosTable 1.3.6.1.4.1.9.9.817.1.1.2.5
This table contains 4G/LTE QoS parameters requested by modem to the cellular network via PDN Context Activation Request message.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CwceLteEpsBearerQosEntry

cwceLteEpsBearerQosEntry 1.3.6.1.4.1.9.9.817.1.1.2.5.1
An entry contains management information of Cellular 4G/LTE QoS parameters. An entry of this table is created if an interface capable of providing operational Cellular 4G/LTE QoS parameters is detected by the agent. An entry of this table is deleted by the agent if the corresponding entry in ifTable is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  CwceLteEpsBearerQosEntry  

cwceLteEpsBearerId 1.3.6.1.4.1.9.9.817.1.1.2.5.1.1
This object indicates the EPS Bearer Identity which is allocated by the Mobility Management Entity (MME).
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cwceLteEpsBearerType 1.3.6.1.4.1.9.9.817.1.1.2.5.1.2
This object indicates the type of bearers. gbr - Guaranteed Bit Rate(GBR). GBR bearer has a minimum amount of bandwidth that is reserved by the network, and these resources are always consumed in a radio base station regardless of whether it is used or not. nonGbr - non-Guaranteed Bit Rate(Non-GBR). Non-GBR bearers are for best-effort services and do not consume any network resources. unknown - the type of bearers is unknown.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER gbr(1), nonGbr(2), unknown(3)  

cwceLteEpsQCI 1.3.6.1.4.1.9.9.817.1.1.2.5.1.3
This object indicates the QoS Class Identifier(QCI). The QCI along with the ARP characterizes the QoS of the bearer.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cwceLteEpsArp 1.3.6.1.4.1.9.9.817.1.1.2.5.1.4
This object indicates the Allocation and Retention Priority(ARP). ARP is a QoS parameter designed to facilitate decisions as to whether a bearer establishment/modification request can be accepted.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cwceLteEpsBearerResType 1.3.6.1.4.1.9.9.817.1.1.2.5.1.5
This object indicates the Bearer resource type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER defaultBearer(1), dedicatedBearer(2), unknown(3)  

cwceLteEpsGbr 1.3.6.1.4.1.9.9.817.1.1.2.5.1.6
This object indicates the Guaranteed Bit Rate(GBR) which determines the resource reservation to guarantee a given data rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cwceLteEpsMbr 1.3.6.1.4.1.9.9.817.1.1.2.5.1.7
This object indicates the Maximum Bit Rate(MBR) which is used for policing the user traffic.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cwceLteEpsAmbr 1.3.6.1.4.1.9.9.817.1.1.2.5.1.8
This object indicates the Aggregated Maximum Bit Rate. This object is valid only if the value of the corresponding cwceLteEpsBearerResType is 'defaultBearer'.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cwceLteEpsTotalBytesTx 1.3.6.1.4.1.9.9.817.1.1.2.5.1.9
This object indicates the total data bytes transmitted by this bearer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

cwceLteEpsTotalBytesRx 1.3.6.1.4.1.9.9.817.1.1.2.5.1.10
This object indicates the total data bytes received by this bearer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

cwceLteEpsPacketsTx 1.3.6.1.4.1.9.9.817.1.1.2.5.1.11
This object indicates the number of packets transmitted by this bearer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

cwceLteEpsPacketsRx 1.3.6.1.4.1.9.9.817.1.1.2.5.1.12
This object indicates the number of packets received by this bearer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

cwceLteRsrqOnsetNotif 1.3.6.1.4.1.9.9.817.0.1
If RSRQ goes below cwceLteRsrqOnsetNotifThreshold and the service bit in cwceLteRsrqOnsetNotifFlag is set, this notification will be generated. Object cwceLteRsrqOnsetNotifFlag will indicate which service generates this notification and the associated RSRQ will be reported in cwceLteNotifRsrq. Please note that cwceLteNotifRsrq is used to indicate the RSRQ value that triggers the notification, user should go to the corresponding radio table to get the current RSRQ value.
Status: current Access: read-only
NOTIFICATION-TYPE    

cwceLteRsrqAbateNotif 1.3.6.1.4.1.9.9.817.0.2
If RSRQ goes above cwceLteRsrqAbateNotifThreshold and the service bit in cwceLteRsrqOnsetNotifFlag is set, this notification will be generated. Object cwceLteRsrqAbateNotifFlag will indicate which service generates this notification and the associated RSRQ will be reported in cwceLteNotifRsrq. Please note that cwceLteNotifRsrq is used to indicate the RSRQ value that triggers the notification, user should go to the corresponding radio table to get the current RSRQ value.
Status: current Access: read-only
NOTIFICATION-TYPE    

cwceLteRsrpOnsetNotif 1.3.6.1.4.1.9.9.817.0.3
If RSRP goes below cwceLteRsrpOnsetNotifThreshold and the service bit in cwceLteRsrpOnsetNotifFlag is set, this notification will be generated. Object cwceLteRsrpOnsetNotifFlag will indicate which service generates this notification and the associated RSRP will be reported in cwceLteNotifRsrp. Please note that cwceLteNotifRsrp is used to indicate the RSRP value that triggers the notification, user should go to the corresponding radio table to get the current RSRP value.
Status: current Access: read-only
NOTIFICATION-TYPE    

cwceLteRsrpAbateNotif 1.3.6.1.4.1.9.9.817.0.4
If RSRP goes above cwceLteRsrqAbateNotifThreshold and the service bit in cwceLteRsrpOnsetNotifFlag is set, this notification will be generated. Object cwceLteRsrpAbateNotifFlag will indicate which service generates this notification and the associated RSRP will be reported in cwceLteNotifRsrp. Please note that cwceLteNotifRsrp is used to indicate the RSRP value that triggers the notification, user should go to the corresponding radio table to get the current RSRP value.
Status: current Access: read-only
NOTIFICATION-TYPE    

ciscoWanCellExtMIBCompliances 1.3.6.1.4.1.9.9.817.2.1
OBJECT IDENTIFIER    

ciscoWanCellExtMIBGroups 1.3.6.1.4.1.9.9.817.2.2
OBJECT IDENTIFIER    

ciscoWanCellExtMIBCompliance 1.3.6.1.4.1.9.9.817.2.1.1
The compliance statement for the CISCO-WAN-CELL-EXT-MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

ciscoWanCellExtMIBLteObjectGroup 1.3.6.1.4.1.9.9.817.2.2.1
A collection of objects for Cellular 4G/LTE.
Status: current Access: read-only
OBJECT-GROUP    

ciscoWanCellExtMIBNotificationGroup 1.3.6.1.4.1.9.9.817.2.2.2
A collection of objects for Cellular WAN notifications.
Status: current Access: read-only
NOTIFICATION-GROUP