CISCO-TN3270SERVER-MIB

File: CISCO-TN3270SERVER-MIB.mib (57243 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Gauge32 IpAddress TEXTUAL-CONVENTION
DisplayString MacAddress TimeStamp
TruthValue MODULE-COMPLIANCE OBJECT-GROUP
ciscoMgmt

Defined Types

Tn3270sUnsigned32  
Unsigned32 definition. To be replaced by Unsigned32 from SNMPv2-SMI when its implememted.
TEXTUAL-CONVENTION    
  INTEGER 0..4294967295  

Tn3270sTCPPort  
A range for tn3270 port addresses.
TEXTUAL-CONVENTION    
  INTEGER 0..65535  

Tn3270sPUIndex  
Address range for a PU.
TEXTUAL-CONVENTION    
  Tn3270sUnsigned32  

Tn3270sLUIndex  
Address range for a LU.
TEXTUAL-CONVENTION    
  Tn3270sUnsigned32  

Tn3270sCpuCard  
The identity of the board running the server. The values are as follows: 'CIP slot ' 'ECPA bay ' 'PCPA bay ' where number is a positive integer indicating the location on the platform the card is installed in.
TEXTUAL-CONVENTION    
  DisplayString Size(10..16)  

Tn3270sGlobalEntry  
SEQUENCE    
  tn3270sIndex Tn3270sUnsigned32
  tn3270sCpuCard Tn3270sCpuCard
  tn3270sMaxLus Tn3270sUnsigned32
  tn3270sLusInUse Gauge32
  tn3270sStartupTime TimeStamp
  tn3270sGlobalTcpPort Tn3270sTCPPort
  tn3270sGlobalIdleTimeout INTEGER
  tn3270sGlobalKeepAlive INTEGER
  tn3270sGlobalUnbindAction INTEGER
  tn3270sGlobalGenericPool INTEGER
  tn3270sTimingMarkSupported TruthValue
  tn3270sRunningTime Tn3270sUnsigned32

Tn3270sStatsEntry  
SEQUENCE    
  tn3270sStatsServerAddr IpAddress
  tn3270sStatsServerTcpPort Tn3270sTCPPort
  tn3270sStatsMaxSess Gauge32
  tn3270sStatsSpareSess Gauge32
  tn3270sStatsConnectsIn Counter32
  tn3270sStatsDisconnects Counter32
  tn3270sStatsTN3270ConnectsFailed Counter32
  tn3270sStatsInboundChains Counter32
  tn3270sStatsOutboundChains Counter32
  tn3270sStatsSampledHostResponses Counter32
  tn3270sStatsNetSampledHostResponseTime Tn3270sUnsigned32
  tn3270sStatsSampledClientResponses Counter32
  tn3270sStatsNetSampledClientResponseTime Tn3270sUnsigned32

Tn3270sPuEntry  
SEQUENCE    
  tn3270sPuIndex Tn3270sPUIndex
  tn3270sPuIpAddr IpAddress
  tn3270sPuTcpPort Tn3270sTCPPort
  tn3270sPuIdleTimeout INTEGER
  tn3270sPuKeepAlive INTEGER
  tn3270sPuUnbindAction INTEGER
  tn3270sPuGenericPool INTEGER
  tn3270sPuState INTEGER
  tn3270sPuType INTEGER
  tn3270sPuLuSeed DisplayString
  tn3270sLocalSapAddress INTEGER
  tn3270sRemoteSapAddress INTEGER
  tn3270sRemoteMacAddress MacAddress
  tn3270sPuIpPrecedenceScreen INTEGER
  tn3270sPuIpPrecedencePrinter INTEGER
  tn3270sPuIpTosScreen INTEGER
  tn3270sPuIpTosPrinter INTEGER

Tn3270sIpEntry  
SEQUENCE    
  tn3270sIpClientAddr IpAddress
  tn3270sIpClientTcpPort Tn3270sTCPPort
  tn3270sIpPuIndex Tn3270sPUIndex
  tn3270sIpLuIndex Tn3270sLUIndex

Tn3270sLuEntry  
SEQUENCE    
  tn3270sLuPuIndex Tn3270sPUIndex
  tn3270sLuIndex Tn3270sLUIndex
  tn3270sLuClientAddr IpAddress
  tn3270sLuClientTcpPort Tn3270sTCPPort
  tn3270sLuTelnetType INTEGER
  tn3270sLuTermModel DisplayString
  tn3270sLuState INTEGER
  tn3270sLuCurInbPacing INTEGER
  tn3270sLuCurInbQsize INTEGER
  tn3270sLuCurOutQsize INTEGER
  tn3270sLuIdleTime INTEGER
  tn3270sLuType INTEGER
  tn3270sLuAppnLinkIndex DisplayString
  tn3270sLuLfsid INTEGER
  tn3270sLuLastEvent TimeStamp
  tn3270sLuEvents OCTET STRING
  tn3270sLuNail TruthValue

Tn3270sPuNailEntry  
SEQUENCE    
  tn3270sPuNailClientIpAddr IpAddress
  tn3270sPuNailClientIpMask IpAddress
  tn3270sPuNailType INTEGER
  tn3270sPuNailLuFirst INTEGER
  tn3270sPuNailLuLast INTEGER

Tn3270sIpNailEntry  
SEQUENCE    
  tn3270sIpNailClientIpAddr IpAddress
  tn3270sIpNailClientIpMask IpAddress
  tn3270sIpNailType INTEGER
  tn3270sIpNailLuFirst INTEGER
  tn3270sIpNailLuLast INTEGER

Defined Values

ciscoTn3270ServerMIB 1.3.6.1.4.1.9.9.54
The MIB module for TN3270 Server. MIB description The PU and LU MIB are defined in RFC 1666. This MIB provides additional information on IP and LU mapping. The following entities are managed: 1) TN3270S Global 2) TN3270S Stats on Listen IP/Port basis 3) TN3270S PU 4) TN3270S IP to LU Mapping 5) TN3270S LU to IP Mapping
MODULE-IDENTITY    

tn3270sObjects 1.3.6.1.4.1.9.9.54.1
OBJECT IDENTIFIER    

tn3270sGlobal 1.3.6.1.4.1.9.9.54.1.1
OBJECT IDENTIFIER    

tn3270sStats 1.3.6.1.4.1.9.9.54.1.2
OBJECT IDENTIFIER    

tn3270sPu 1.3.6.1.4.1.9.9.54.1.3
OBJECT IDENTIFIER    

tn3270sIp 1.3.6.1.4.1.9.9.54.1.4
OBJECT IDENTIFIER    

tn3270sLu 1.3.6.1.4.1.9.9.54.1.5
OBJECT IDENTIFIER    

tn3270sPuNail 1.3.6.1.4.1.9.9.54.1.6
OBJECT IDENTIFIER    

tn3270sIpNail 1.3.6.1.4.1.9.9.54.1.7
OBJECT IDENTIFIER    

tn3270sGlobalTable 1.3.6.1.4.1.9.9.54.1.1.1
A list of TN3270 server and DLUR global information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270sGlobalEntry

tn3270sGlobalEntry 1.3.6.1.4.1.9.9.54.1.1.1.1
Parameters values for a group.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sGlobalEntry  

tn3270sIndex 1.3.6.1.4.1.9.9.54.1.1.1.1.1
Index used to uniquely identify each tn3270 server instance. This index value shall not be reused when the server is shut down and a new instance invoked.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sUnsigned32  

tn3270sCpuCard 1.3.6.1.4.1.9.9.54.1.1.1.1.2
The identity of the board running the server.
Status: current Access: read-only
OBJECT-TYPE    
  Tn3270sCpuCard  

tn3270sMaxLus 1.3.6.1.4.1.9.9.54.1.1.1.1.3
The maximum number of LUs supported by the server.
Status: current Access: read-only
OBJECT-TYPE    
  Tn3270sUnsigned32 1..65535  

tn3270sLusInUse 1.3.6.1.4.1.9.9.54.1.1.1.1.4
The number of LUs currently in use on the server.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..65535  

tn3270sStartupTime 1.3.6.1.4.1.9.9.54.1.1.1.1.5
The timestamp when the tn3270 server started.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tn3270sGlobalTcpPort 1.3.6.1.4.1.9.9.54.1.1.1.1.6
The default TCP port of this TN3270 Server, which is inherited by the PU if it doesn't have the TCP port explicitly defined in the router configuration for this PU.
Status: current Access: read-only
OBJECT-TYPE    
  Tn3270sTCPPort  

tn3270sGlobalIdleTimeout 1.3.6.1.4.1.9.9.54.1.1.1.1.7
The number of seconds of LU inactivity (from either host or client) before the TN3270 session is disconnected. Zero seconds means that LU sessions, by default, will not be disconnected when inactive, regardless of the amount of idle time spent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

tn3270sGlobalKeepAlive 1.3.6.1.4.1.9.9.54.1.1.1.1.8
The number of seconds of inactivity from client side which the TN3270 Server allows to elapse before sending DO-TIMING-MARK to the TN3270 client. If the client does not reply within thirty minutes of such a TIMING-MARK sending, the server disconnects the tn3270 session. Zero seconds indicates that no keepalives will be sent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65534  

tn3270sGlobalUnbindAction 1.3.6.1.4.1.9.9.54.1.1.1.1.9
This variable indicates whether or not a tn3270 session will be disconnected upon UNBIND. keep indicates that no automatic disconnect will be made by the server upon receipt of an UNBIND. disconnect indicates that the session will be disconnected upon receipt of an UNBIND.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER keep(1), disconnect(2)  

tn3270sGlobalGenericPool 1.3.6.1.4.1.9.9.54.1.1.1.1.10
This variable indicates whether or not leftover LUs will be made available to tn3270 sessions which do not request a specific LU or LU pool. A 'leftover' LU is defined as one for which all of the following conditions hold true: .the SSCP did not send an ACTLU during PU startup; and .the PU controlling the LU is capable of carrying PSID vectors on NMVT messages(thus allowing DDDLU operation for that LU). deny indicates that the leftover LUs should not be given to a generic pool (ie, the PU is not automatically fully populated with 255 LOCADDR definitions); permit indicates leftover LUs should be made available to tn3270 users wanting 'generic' sessions. All LUs in the generic pool are (by definition) Dynamic Definition of Dependant (DDDLU) capable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

tn3270sTimingMarkSupported 1.3.6.1.4.1.9.9.54.1.1.1.1.11
This variable indicates whether to send a timing mark to solicit a response before sending a response to the host. true indicates that a timing mark is sent, false indicates that it is not sent. By using timing mark, an application can determine the response time from the client. Some existing clients do not implement the timing mark correctly and will not work with this server if this parameter is set to true
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

tn3270sRunningTime 1.3.6.1.4.1.9.9.54.1.1.1.1.12
Total time elapsed since start of tn3270 server.
Status: current Access: read-only
OBJECT-TYPE    
  Tn3270sUnsigned32  

tn3270sStatsTable 1.3.6.1.4.1.9.9.54.1.2.1
A list of statistics for each TN3270 Server Listening IP/Port pair.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270sStatsEntry

tn3270sStatsEntry 1.3.6.1.4.1.9.9.54.1.2.1.1
The entry contains parameters which describe the statistics of the ip stacks.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sStatsEntry  

tn3270sStatsServerAddr 1.3.6.1.4.1.9.9.54.1.2.1.1.1
The ip address of this TN3270 Server Listen endpoint.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

tn3270sStatsServerTcpPort 1.3.6.1.4.1.9.9.54.1.2.1.1.2
The TCP port in this TN3270 Server Listen endpoint.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sTCPPort  

tn3270sStatsMaxSess 1.3.6.1.4.1.9.9.54.1.2.1.1.3
Number of Tn3270 sessions configured which are available to be used by tn3270 clients.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tn3270sStatsSpareSess 1.3.6.1.4.1.9.9.54.1.2.1.1.4
Spare number of TN3270 sessions available for connect at query time.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tn3270sStatsConnectsIn 1.3.6.1.4.1.9.9.54.1.2.1.1.5
Total number of TN3270 session connects-in received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tn3270sStatsDisconnects 1.3.6.1.4.1.9.9.54.1.2.1.1.6
Total number of TN3270 sessions disconnected.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tn3270sStatsTN3270ConnectsFailed 1.3.6.1.4.1.9.9.54.1.2.1.1.7
Total number of attempted sessions which failed to negotiate TN3270/E or were rejected by control point.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tn3270sStatsInboundChains 1.3.6.1.4.1.9.9.54.1.2.1.1.8
Total number of inbound(from client to host) RU chains (identified by end of record (EOR)) processed. Since every inbound RU chain is accompanied by client giving host the direction(CD), it is also a count of number of client transactions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tn3270sStatsOutboundChains 1.3.6.1.4.1.9.9.54.1.2.1.1.9
Total number of Outbound(from host to client) RU Chains (identified by EOR) processed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tn3270sStatsSampledHostResponses 1.3.6.1.4.1.9.9.54.1.2.1.1.10
Total number of Sampled Inbound Transactions (identified by EOR) on which response time is computed since restart of last listen on ServerAddress/TcpPort. Counters get reset at that point.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tn3270sStatsNetSampledHostResponseTime 1.3.6.1.4.1.9.9.54.1.2.1.1.11
Total response time for all sampled inbound transactions for which response time is computed. Response time is the time difference between receiving EOR from the client, and receiving the response from the host. Note that the average response time is given by this object divided by tn3270sStatsSampledHostResponses.
Status: current Access: read-only
OBJECT-TYPE    
  Tn3270sUnsigned32  

tn3270sStatsSampledClientResponses 1.3.6.1.4.1.9.9.54.1.2.1.1.12
Total number of sampled outbound timing marks on which response time computed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tn3270sStatsNetSampledClientResponseTime 1.3.6.1.4.1.9.9.54.1.2.1.1.13
Total response time for all sampled timing marks on which response time is computed. Response time is the time diference between sending the timeing mark to the client and receiving the response from the client. Note that this is only valid if timeing mark is configured. Note that the average outbound response time is given by this object divided by tn3270sStatsSampledClientResponses.
Status: current Access: read-only
OBJECT-TYPE    
  Tn3270sUnsigned32  

tn3270sPuTable 1.3.6.1.4.1.9.9.54.1.3.1
This table contains objects which describe the PU configuration parameters not defined in the NAU mib, APPN mib or DLUR mib
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270sPuEntry

tn3270sPuEntry 1.3.6.1.4.1.9.9.54.1.3.1.1
A list of TN3270 server PU parameters
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sPuEntry  

tn3270sPuIndex 1.3.6.1.4.1.9.9.54.1.3.1.1.1
Index used to uniquely identify each Node instance. This is the same as snaNodeAdminIndex in the NAU MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sPUIndex  

tn3270sPuIpAddr 1.3.6.1.4.1.9.9.54.1.3.1.1.2
The ip address of this TN3270 server.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

tn3270sPuTcpPort 1.3.6.1.4.1.9.9.54.1.3.1.1.3
The TCP port of this TN3270 server telnet session.
Status: current Access: read-only
OBJECT-TYPE    
  Tn3270sTCPPort  

tn3270sPuIdleTimeout 1.3.6.1.4.1.9.9.54.1.3.1.1.4
The number of seconds of LU inactivity (from either host or client) before the TN3270 session is disconnected. Zero seconds means that LU sessions, by default, will not be disconnected when inactive, regardless of the amount of idle time spent. 65535 (not valid in server context) indicates that the idletime value should be taken from the server context.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

tn3270sPuKeepAlive 1.3.6.1.4.1.9.9.54.1.3.1.1.5
The number of seconds of inactivity from client side which the TN3270 Server allows to elapse before sending DO-TIMING-MARK to the TN3270 client. If the client does not reply within thirty minutes of such a TIMING-MARK sending, the server disconnect the tn3270 session. Zero seconds indicates that no keepalives will be sent. 65535 (not valid in server context) indicates that the default keepalive value for an LU is taken from whatever value had been defined in the server context for this CIP card.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

tn3270sPuUnbindAction 1.3.6.1.4.1.9.9.54.1.3.1.1.6
This variable indicates whether or not a tn3270 session will be disconnected upon UNBIND. keep indicates that no automatic disconnect will be made by the server upon receipt of an UNBIND. disconnect indicates that the session will be disconnected upon receipt of an UNBIND. inherit indicates that the default keepalive value of an LU is taken from whatever value had been defined in the server context for this CIP card.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER keep(1), disconnect(2), inherit(3)  

tn3270sPuGenericPool 1.3.6.1.4.1.9.9.54.1.3.1.1.7
This variable indicates whether or not leftover LUs will be made available to tn3270 sessions which do not request a specific LU or LU pool. A 'leftover' LU is defined as one for which all of the following conditions hold true: .the SSCP did not send an ACTLU during PU startup; and .the PU controlling the LU is capable of carrying PSID vectors on NMVT messages (thus allowing DDDLU operation for that LU). inherit indicates that the value of tn3270sPuGenericPool is to be the same as tn3270sGlobalGenericPool. deny indicates that the leftover LUs should not be given to a generic pool (ie, the PU is not automatically fully populated with 255 LOCADDR definitions); permit indicates leftover LUs should be made available to tn3270 users wanting 'generic' sessions. All LUs in the generic pool are (by definition) DDDLU capable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER permit(1), deny(2), inherit(3)  

tn3270sPuState 1.3.6.1.4.1.9.9.54.1.3.1.1.8
The value identifies the current PU state. This has a different meaning for direct or DLUR PU before the link station is established. For DLUR PU, the PU is in reset state, for direct PU, this will be either sending a TEST or XID shut (1) - The PU is configured but in shut state reset (2) - The link station of this PU is not active. inactive (3) - The PU is not activated and the link-station or DLUR state is unknown. test (4) - PU is sending a TEST to establish link. xid (5) - TEST is responded, XID is sent. pActpu (6) - The link station is up but no ACTPU is received. active (7) - ACTPU is received and acknowledged positively. actBusy (8) - Awaiting host to acknowledge the SSCP-PU data.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER shut(1), reset(2), inactive(3), test(4), xid(5), pActpu(6), active(7), actBusy(8)  

tn3270sPuType 1.3.6.1.4.1.9.9.54.1.3.1.1.9
This defines whether the connection to the host is via DLUR or direct link. If DLUR, LuSeed, lmac/sap, and rmac/sap in this table are undefined.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dlur(1), direct(2)  

tn3270sPuLuSeed 1.3.6.1.4.1.9.9.54.1.3.1.1.10
For Direct PU this defines the LU name prefix (LU seed) which is concatinated with the locaddr to form a unique name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..6)  

tn3270sLocalSapAddress 1.3.6.1.4.1.9.9.54.1.3.1.1.11
SAP address of the local direct node.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..254  

tn3270sRemoteSapAddress 1.3.6.1.4.1.9.9.54.1.3.1.1.12
SAP address of the remote node; valid for direct PU only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..254  

tn3270sRemoteMacAddress 1.3.6.1.4.1.9.9.54.1.3.1.1.13
MAC address of the remote node; valid for direct PU only.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

tn3270sPuIpPrecedenceScreen 1.3.6.1.4.1.9.9.54.1.3.1.1.14
The value of the PRECEDENCE field in the Type of Service octet in the IP header set by the TN3270 server for outbound IP packets destined to the TN3270 client screen. That is from the router to the TN3270 client screen.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

tn3270sPuIpPrecedencePrinter 1.3.6.1.4.1.9.9.54.1.3.1.1.15
The value of the PRECEDENCE field in the Type of Service octet in the IP header set by the TN3270 server for outbound IP packets destined to the TN3270 client printer. That is from the router to the TN3270 client printer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

tn3270sPuIpTosScreen 1.3.6.1.4.1.9.9.54.1.3.1.1.16
The value of the TOS field in the Type of Service octet in the IP header set by the TN3270 server for outbound IP packets destined to the TN3270 client screen. That is from the router to the TN3270 client screen.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..15  

tn3270sPuIpTosPrinter 1.3.6.1.4.1.9.9.54.1.3.1.1.17
The value of the TOS field in the Type of Service octet in the IP header set by the TN3270 server for outbound IP packets destined to the TN3270 client printer. That is from the router to the TN3270 client printer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..15  

tn3270sIpTable 1.3.6.1.4.1.9.9.54.1.4.1
A list of IP to LU mapping entries
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270sIpEntry

tn3270sIpEntry 1.3.6.1.4.1.9.9.54.1.4.1.1
A list of entries to relate a client IP address to the LU
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sIpEntry  

tn3270sIpClientAddr 1.3.6.1.4.1.9.9.54.1.4.1.1.1
The ip address of the TN3270 client.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

tn3270sIpClientTcpPort 1.3.6.1.4.1.9.9.54.1.4.1.1.2
The TCP port of the TN3270 client.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sTCPPort  

tn3270sIpPuIndex 1.3.6.1.4.1.9.9.54.1.4.1.1.3
The PU index associated with NAU and PU objects
Status: current Access: read-only
OBJECT-TYPE    
  Tn3270sPUIndex  

tn3270sIpLuIndex 1.3.6.1.4.1.9.9.54.1.4.1.1.4
The LU index associated with NAU and LU objects.
Status: current Access: read-only
OBJECT-TYPE    
  Tn3270sLUIndex  

tn3270sLuTable 1.3.6.1.4.1.9.9.54.1.5.1
This helps map LU to client ip/port. Also it provides other useful parameters not available elsewhere.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270sLuEntry

tn3270sLuEntry 1.3.6.1.4.1.9.9.54.1.5.1.1
Parameters values for a group.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sLuEntry  

tn3270sLuPuIndex 1.3.6.1.4.1.9.9.54.1.5.1.1.1
Index used to uniquely identify each PU instance. This is the same as snaNodeAdminIndex in the NAU MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sPUIndex  

tn3270sLuIndex 1.3.6.1.4.1.9.9.54.1.5.1.1.2
Index used to uniquely identify the LU instance within a PU. It is the locaddr. This is the same as snaLuAdminLuIndex in the NAU MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sLUIndex  

tn3270sLuClientAddr 1.3.6.1.4.1.9.9.54.1.5.1.1.3
The ip address of the TN3270 client connected to this LU.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

tn3270sLuClientTcpPort 1.3.6.1.4.1.9.9.54.1.5.1.1.4
The TCP port of the TN3270 client connected to this LU.
Status: current Access: read-only
OBJECT-TYPE    
  Tn3270sTCPPort  

tn3270sLuTelnetType 1.3.6.1.4.1.9.9.54.1.5.1.1.5
This indicates whether the negotiated TN3270 session. TN3270, TN3270E or never connected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER tn3270(1), tn3270e(2), neverConnect(3)  

tn3270sLuTermModel 1.3.6.1.4.1.9.9.54.1.5.1.1.6
Terminal type or model number of the incoming TN3270 client.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..17)  

tn3270sLuState 1.3.6.1.4.1.9.9.54.1.5.1.1.7
The value identifies the current LU state. inactive (1) - LU didn't receive ACTLU. active (2) - LU received ACTLU and acknowledged positively. pSdt (3) - LU is bound but there is no SDT yet. act/session (4) - LU is bound and in session. pActlu (5) - telnet connects in and is awating for ACTLU. pNotifyAv (6) - awaiting host notify-available response. pNotifyUa (7) - awaiting host notify-unavailable response. pReset (8) - awaiting for a buffer to send DACTLU response. pPsid (9) - awaiting for NMVT Reply psid response. pBind (10) - awaiting for host to send bind. pUnbind (11) - awaiting host unbind response. unbindWt (12) - awaiting for client to acknowledge disconnection. sdtWt (13) - awaiting for client to acknowledge SDT
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), active(2), pSdt(3), actSession(4), pActlu(5), pNotifyAv(6), pNotifyUa(7), pReset(8), pPsid(9), pBind(10), pUnbind(11), unbindWt(12), sdtWt(13)  

tn3270sLuCurInbPacing 1.3.6.1.4.1.9.9.54.1.5.1.1.8
The number of inbound frames allowed to be sent to the host without receiving a pacing response from the host.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..63  

tn3270sLuCurInbQsize 1.3.6.1.4.1.9.9.54.1.5.1.1.9
After inbound pacing credit is exhausted, the inbound data is queued. This is the number of inbound frames queued waiting for host pacing response.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..63  

tn3270sLuCurOutQsize 1.3.6.1.4.1.9.9.54.1.5.1.1.10
The number of TCP packets in the server queued for transmission to the client
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..63  

tn3270sLuIdleTime 1.3.6.1.4.1.9.9.54.1.5.1.1.11
Time since last activity was recorded on this LU.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

tn3270sLuType 1.3.6.1.4.1.9.9.54.1.5.1.1.12
This indicates whether LU is dynamic or static. dynamic (1) - LU is configured as DDDLU. static (2) - LU is configured as specific. Host will send ACTLU as soon as PU is active.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dynamic(1), static(2)  

tn3270sLuAppnLinkIndex 1.3.6.1.4.1.9.9.54.1.5.1.1.13
This is the link index into APPN mib for link on which bind flowed; only valid for DLUR LU.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

tn3270sLuLfsid 1.3.6.1.4.1.9.9.54.1.5.1.1.14
This is the session identifier on a PU 2.1 link.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

tn3270sLuLastEvent 1.3.6.1.4.1.9.9.54.1.5.1.1.15
Time at which the last data was logged for this LU.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TimeStamp  

tn3270sLuEvents 1.3.6.1.4.1.9.9.54.1.5.1.1.16
An array of octets indicating the latest events which happened in this LU. Octet 1 is the most recent event, octet 2 the next most recent and so on. Although the maximum number of events kept is 16, the actual number of events kept may be lower than that. When more events are generated than are kept, the oldest ones are discarded. Events are encoded as: 1 inactivity timer expired. 2 dynamic timer expired, 3 actlu from host 4 bind from host 5 clear from host 6 dactlu from host 7 hierarchical reset from PU (warn actpu) 8 sdt from host 9 unbind from host 10 notify response from host 11 Reply psid negative response from host 12 Reply psid pos response from host 13 unbind response from host 14 hierarchical reset from pu 15 connect from client 16 disconnect from client 17 timing-mark response from client 18 flow control timer expired 19 negative response to host 20 negative response from host 21 data contention happened 22 no buffer to send response 23 receive a sna response while inbound
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

tn3270sLuNail 1.3.6.1.4.1.9.9.54.1.5.1.1.17
This variable indicates whether this LU has been configured (Nailed) for a specific TN3270 client. TRUE -> LU is nailed to the client IP address FALSE -> LU is not nailed to the client IP address
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

tn3270sPuNailTable 1.3.6.1.4.1.9.9.54.1.6.1
A list of reserved LUs and their associated IP addresses is represented here for the containing PU. Each LU is configured for a specific client IP address. This association between the LU and the client IP Address is called nailing. The client is said to be nailed to its LU and visa-versa. If the client IP address is known but the PU index is not known, a more efficient way to access this info is via tn3270sIpNailTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270sPuNailEntry

tn3270sPuNailEntry 1.3.6.1.4.1.9.9.54.1.6.1.1
A list of entries to relate a PU to nailed clients.This table contains the same info as tn3270sIpNailTable. The indices are ordered to facilitate access to the information when the PU index is known but not the client IP address. This is necessitated due to the potentially large number of rows in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sPuNailEntry  

tn3270sPuNailClientIpAddr 1.3.6.1.4.1.9.9.54.1.6.1.1.1
The IP address of the nailed TN3270 client.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

tn3270sPuNailClientIpMask 1.3.6.1.4.1.9.9.54.1.6.1.1.2
The subnet mask of the nailed TN3270 client.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

tn3270sPuNailType 1.3.6.1.4.1.9.9.54.1.6.1.1.3
The nailing type configured for the range of LUs within this PU is either screen or printer. screen - The range of LUs will only be connected to TN3270 clients with a device type which is not 328*. If an LU is statically configured at the host, then it should be configured with a screen DLOGMOD definition. printer - The range of LUs will only be connected to TN3270 clients with device type which is 328*. If an LU is statically configured at the host, then it should be configured with a printer DLOGMOD definition.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER screen(1), printer(2)  

tn3270sPuNailLuFirst 1.3.6.1.4.1.9.9.54.1.6.1.1.4
The first LU in this range nailed to this client ip address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

tn3270sPuNailLuLast 1.3.6.1.4.1.9.9.54.1.6.1.1.5
The last LU in this range nailed to this client ip address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

tn3270sIpNailTable 1.3.6.1.4.1.9.9.54.1.7.1
A list of reserved LUs and their associated IP addresses is represented here for the containing PU. Each LU is configured for a specific client IP address. This association between the LU and the client IP Address is called nailing. The client is said to be nailed to its LU and visa-versa. If the PU index is known but the client IP address is not known, a more efficient way to access this info is via tn3270sPuNailTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Tn3270sIpNailEntry

tn3270sIpNailEntry 1.3.6.1.4.1.9.9.54.1.7.1.1
A list of entries to relate a PU to nailed clients. This table contains the same info as tn3270sPuNailTable. The indices are ordered to facilitate access to the info when the client IP address is known but not the PU index. This is necessitated due to the potentially large number of rows in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Tn3270sIpNailEntry  

tn3270sIpNailClientIpAddr 1.3.6.1.4.1.9.9.54.1.7.1.1.1
The IP address of the nailed TN3270 client.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

tn3270sIpNailClientIpMask 1.3.6.1.4.1.9.9.54.1.7.1.1.2
The subnet mask of the nailed TN3270 client.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

tn3270sIpNailType 1.3.6.1.4.1.9.9.54.1.7.1.1.3
The nailing type configured for the range of LUs within this PU is either screen or printer. screen - The range of LUs will only be connected to TN3270 clients with a device type which is not 328*. If an LU is statically configured at the host, then it should be configured with a screen DLOGMOD definition. printer - The range of LUs will only be connected to TN3270 clients with device type which is 328*. If an LU is statically configured at the host, then it should be configured with a printer DLOGMOD definition.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER screen(1), printer(2)  

tn3270sIpNailLuFirst 1.3.6.1.4.1.9.9.54.1.7.1.1.4
The first LU in this range nailed to this client ip address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

tn3270sIpNailLuLast 1.3.6.1.4.1.9.9.54.1.7.1.1.5
The last LU in this range nailed to this client ip address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

ciscoTn3270ServerMIBNotificationPrefix 1.3.6.1.4.1.9.9.54.2
OBJECT IDENTIFIER    

ciscoTn3270ServerMIBConformance 1.3.6.1.4.1.9.9.54.3
OBJECT IDENTIFIER    

ciscoTn3270ServerMIBCompliances 1.3.6.1.4.1.9.9.54.3.1
OBJECT IDENTIFIER    

ciscoTn3270ServerMIBGroups 1.3.6.1.4.1.9.9.54.3.2
OBJECT IDENTIFIER    

ciscoTn3270ServerMIBCompliance 1.3.6.1.4.1.9.9.54.3.1.1
The compliance statement for entities which implement the Cisco Tn3270s MIB
Status: current Access: read-only
MODULE-COMPLIANCE    

ciscoTn3270ServerMIBGroup 1.3.6.1.4.1.9.9.54.3.2.1
A collection of objects providing Tn3270 ability to a Cisco agent.
Status: current Access: read-only
OBJECT-GROUP    

ciscoTn3270ServerMIBComplianceObsolete 1.3.6.1.4.1.9.9.54.3.1.2
The compliance statement for obsolete entities.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

ciscoTn3270ServerMIBGroupObsolete 1.3.6.1.4.1.9.9.54.3.2.2
A collection of objects providing Tn3270 ability to a Cisco agent.
Status: obsolete Access: read-only
OBJECT-GROUP    

ciscoTn3270ServerMIBComplianceRev1 1.3.6.1.4.1.9.9.54.3.1.3
The compliance statement for the TN3270 Server.
Status: current Access: read-only
MODULE-COMPLIANCE    

ciscoTn3270ServerMIBGroupRev1 1.3.6.1.4.1.9.9.54.3.2.3
A collection of objects providing LU nailing and IP precedence features.
Status: current Access: read-only
OBJECT-GROUP