CISCO-OPTICAL-MIB

File: CISCO-OPTICAL-MIB.mib (100468 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Integer32 Unsigned32 TEXTUAL-CONVENTION
TruthValue DisplayString MacAddress
TimeStamp MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP ifIndex ifName
ciscoMgmt

Defined Types

CoiOpticalPower  
This value indicates the optical receive or transmit power.
TEXTUAL-CONVENTION    
  Integer32 -4000..3000  

CoiOpticalWavelength  
This value represents the wavelength of optical signals, in an optical interface. It is represented in units of nanometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under the frequency grid defined in ITU-T G.694.1
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1528770..1604030  

CoiIntervalType  
This value indicates the time period over which performance monitoring data has been collected. Valid values are - fifteenMin(1) - values for the 15 min interval. oneDay(2) - values for the 1 Day interval. thirtySecond(3)- values for the 30 Sec interval.
TEXTUAL-CONVENTION    
  INTEGER fifteenMin(1), oneDay(2), thirtySecond(3)  

CoiPortType  
This value indicates the port type of the optical interface. Valid values are - clientPort(1) - denotes client port. trunkPort(2) - denotes trunk port.
TEXTUAL-CONVENTION    
  INTEGER clientPort(1), trunkPort(2)  

CoiOptAlarmType  
This value indicates the alarm type. alarmUnknown(1) - denotes unknown alarm type. equipmentFailure(2) - denotes equipment fail alarm type.
TEXTUAL-CONVENTION    
  INTEGER alarmUnknown(1), equipmentFailure(2)  

CoiOptAlarmSeverity  
This will indicate the severity of the notification being sent out. Valid values are - notReported(1) - alarm not reported. notAlarmed(2) - alarm not raised. minor(3) - minor alarm. major(4) - major alarm. critical(5) - critical alarm.
TEXTUAL-CONVENTION    
  INTEGER notReported(1), notAlarmed(2), minor(3), major(4), critical(5)  

CoiOptAlarmStatus  
This will indicate the status of the alarm. Valid values are - raised(1) - alarm in raised state. cleared(2) - alarm in cleared state. transient(3)- alarm in transient state.
TEXTUAL-CONVENTION    
  INTEGER raised(1), cleared(2), transient(3)  

CoiOptAlarmServiceAffecting  
This will indicate the sevice-affecting state of the alarm. Valid values are - Service affecting(1) - alarm affects service. Non-Service affecting(2)- alarm does not affect service.
TEXTUAL-CONVENTION    
  INTEGER serviceAffecting(1), nonServiceAffecting(2)  

CoiOpticalControllerEntry  
SEQUENCE    
  coiOpticalControllerWavelength CoiOpticalWavelength
  coiOpticalControllerLaserStatus INTEGER
  coiOpticalControllerFrequency Unsigned32
  coiOpticalControllerChannelNumber Unsigned32
  coiOpticalControllerTransmitPower CoiOpticalPower
  coiOpticalControllerOpticsType DisplayString
  coiOpticalControllerRXLowThreshold CoiOpticalPower
  coiOpticalControllerTXLowThreshold CoiOpticalPower
  coiOpticalControllerRXHighThreshold CoiOpticalPower
  coiOpticalControllerTXHighThreshold CoiOpticalPower
  coiOpticalControllerLBCHighThreshold Integer32
  coiOpticalControllerStatus BITS
  coiOpticalControllerPortType CoiPortType
  coiOpticalControllerTotalRXPower CoiOpticalPower
  coiOpticalControllerTotalTXPower CoiOpticalPower

CoiOpticalControllerPerLaneEntry  
SEQUENCE    
  coiOpticalControllerLane Integer32
  coiOpticalControllerPerLaneRXPower CoiOpticalPower
  coiOpticalControllerPerLaneTXPower CoiOpticalPower
  coiOpticalControllerPerLaneLBC Integer32
  coiOpticalControllerPerLaneOSNR Integer32
  coiOpticalControllerPerLaneChromaticDispersion Integer32
  coiOpticalControllerPerLaneDifferentialGroupDelay Integer32
  coiOpticalControllerPerLaneSecondOrderPMD Integer32
  coiOpticalControllerPerLanePolarizationDependentLoss Integer32
  coiOpticalControllerPerLanePolarizationChangeRate Integer32
  coiOpticalControllerPerLanePhaseNoise Integer32

CoiOpticalClientInfoEntry  
SEQUENCE    
  coiOpticalClientEthernetNeighbourMAC MacAddress

CoiOpticalThresholdEntry  
SEQUENCE    
  coiOptThreshIntervalType CoiIntervalType
  coiOptThreshTXPowerMin CoiOpticalPower
  coiOptThreshRXPowerMin CoiOpticalPower
  coiOptThreshOSNRMin Integer32
  coiOptThreshChromaticDispersionMin Integer32
  coiOptThreshDifferentialGroupDelayMin Integer32
  coiOptThreshSecondOrderPMDMin Integer32
  coiOptThreshPolarizationDependentLossMin Integer32
  coiOptThreshPolarizationChangeRateMin Integer32
  coiOptThreshPhaseNoiseMin Integer32
  coiOptThreshLBCMin Integer32
  coiOptThreshTXPowerMax CoiOpticalPower
  coiOptThreshRXPowerMax CoiOpticalPower
  coiOptThreshOSNRMax Integer32
  coiOptThreshChromaticDispersionMax Integer32
  coiOptThreshDifferentialGroupDelayMax Integer32
  coiOptThreshSecondOrderPMDMax Integer32
  coiOptThreshPolarizationDependentLossMax Integer32
  coiOptThreshPolarizationChangeRateMax Integer32
  coiOptThreshPhaseNoiseMax Integer32
  coiOptThreshLBCMax Integer32
  coiOptThreshTXPowerEnableMin TruthValue
  coiOptThreshRXPowerEnableMin TruthValue
  coiOptThreshOSNREnableMin TruthValue
  coiOptThreshChromaticDispersionEnableMin TruthValue
  coiOptThreshDifferentialGroupDelayEnableMin TruthValue
  coiOptThreshSecondOrderPMDEnableMin TruthValue
  coiOptThreshPolarizationDependentLossEnableMin TruthValue
  coiOptThreshPolarizationChangeRateEnableMin TruthValue
  coiOptThreshPhaseNoiseEnableMin TruthValue
  coiOptThreshLBCEnableMin TruthValue
  coiOptThreshTXPowerEnableMax TruthValue
  coiOptThreshRXPowerEnableMax TruthValue
  coiOptThreshOSNREnableMax TruthValue
  coiOptThreshChromaticDispersionEnableMax TruthValue
  coiOptThreshDifferentialGroupDelayEnableMax TruthValue
  coiOptThreshSecondOrderPMDEnableMax TruthValue
  coiOptThreshPolarizationDependentLossEnableMax TruthValue
  coiOptThreshPolarizationChangeRateEnableMax TruthValue
  coiOptThreshPhaseNoiseEnableMax TruthValue
  coiOptThreshLBCEnableMax TruthValue

CoiOpticalCurrentEntry  
SEQUENCE    
  coiOptCurrentLane Integer32
  coiOptCurrentIntervalType CoiIntervalType
  coiOptCurrentTXPowerMax CoiOpticalPower
  coiOptCurrentRXPowerMax CoiOpticalPower
  coiOptCurrentOSNRMax Integer32
  coiOptCurrentChromaticDispersionMax Integer32
  coiOptCurrentDifferentialGroupDelayMax Integer32
  coiOptCurrentSecondOrderPMDMax Integer32
  coiOptCurrentPolarizationDependentLossMax Integer32
  coiOptCurrentPolarizationChangeRateMax Integer32
  coiOptCurrentPhaseNoiseMax Integer32
  coiOptCurrentLBCMax Integer32
  coiOptCurrentTXPowerMin CoiOpticalPower
  coiOptCurrentRXPowerMin CoiOpticalPower
  coiOptCurrentOSNRMin Integer32
  coiOptCurrentChromaticDispersionMin Integer32
  coiOptCurrentDifferentialGroupDelayMin Integer32
  coiOptCurrentSecondOrderPMDMin Integer32
  coiOptCurrentPolarizationDependentLossMin Integer32
  coiOptCurrentPolarizationChangeRateMin Integer32
  coiOptCurrentPhaseNoiseMin Integer32
  coiOptCurrentLBCMin Integer32
  coiOptCurrentTXPowerAvg CoiOpticalPower
  coiOptCurrentRXPowerAvg CoiOpticalPower
  coiOptCurrentOSNRAvg Integer32
  coiOptCurrentChromaticDispersionAvg Integer32
  coiOptCurrentDifferentialGroupDelayAvg Integer32
  coiOptCurrentSecondOrderPMDAvg Integer32
  coiOptCurrentPolarizationDependentLossAvg Integer32
  coiOptCurrentPolarizationChangeRateAvg Integer32
  coiOptCurrentPhaseNoiseAvg Integer32
  coiOptCurrentLBCAvg Integer32
  coiOptCurrentTimestamp OCTET STRING

CoiOpticalIntervalEntry  
SEQUENCE    
  coiOptIntervalLane Integer32
  coiOptIntervalIntervalType CoiIntervalType
  coiOptIntervalNum Integer32
  coiOptIntervalTXPowerMax CoiOpticalPower
  coiOptIntervalRXPowerMax CoiOpticalPower
  coiOptIntervalOSNRMax Integer32
  coiOptIntervalChromaticDispersionMax Integer32
  coiOptIntervalDifferentialGroupDelayMax Integer32
  coiOptIntervalSecondOrderPMDMax Integer32
  coiOptIntervalPolarizationDependentLossMax Integer32
  coiOptIntervalPolarizationChangeRateMax Integer32
  coiOptIntervalPhaseNoiseMax Integer32
  coiOptIntervalLBCMax Integer32
  coiOptIntervalTXPowerMin CoiOpticalPower
  coiOptIntervalRXPowerMin CoiOpticalPower
  coiOptIntervalOSNRMin Integer32
  coiOptIntervalChromaticDispersionMin Integer32
  coiOptIntervalDifferentialGroupDelayMin Integer32
  coiOptIntervalSecondOrderPMDMin Integer32
  coiOptIntervalPolarizationDependentLossMin Integer32
  coiOptIntervalPolarizationChangeRateMin Integer32
  coiOptIntervalPhaseNoiseMin Integer32
  coiOptIntervalLBCMin Integer32
  coiOptIntervalTXPowerAvg CoiOpticalPower
  coiOptIntervalRXPowerAvg CoiOpticalPower
  coiOptIntervalOSNRAvg Integer32
  coiOptIntervalChromaticDispersionAvg Integer32
  coiOptIntervalDifferentialGroupDelayAvg Integer32
  coiOptIntervalSecondOrderPMDAvg Integer32
  coiOptIntervalPolarizationDependentLossAvg Integer32
  coiOptIntervalPolarizationChangeRateAvg Integer32
  coiOptIntervalPhaseNoiseAvg Integer32
  coiOptIntervalLBCAvg Integer32
  coiOptIntervalTimestamp OCTET STRING

Defined Values

ciscoOpticalMIB 1.3.6.1.4.1.9.9.828
This MIB module defines the managed objects for physical layer characteristics of optical interfaces and performance statistics objects for protocol specific counters in optical devices. Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. Glossary: LBC : Laser Bias Current TX : Transmit RX : Receive PMD : Polarization Mode Dispersion OSNR : Optical Signal to Noise Ratio DGD : Differential Group Delay CD : Chromatic Dispersion rad/s : radian per second dB : decibel dBm : decibel-milliwatt ps : picosecond nm : nanometer.
MODULE-IDENTITY    

ciscoOpticalMIBNotifs 1.3.6.1.4.1.9.9.828.0
OBJECT IDENTIFIER    

ciscoOpticalMIBObjects 1.3.6.1.4.1.9.9.828.1
OBJECT IDENTIFIER    

coiOpticsStatusChange 1.3.6.1.4.1.9.9.828.0.1
This notification is generated whenever the defect status of Optics on an interface changes. Varbind 'ifIndex' indicates the interface whose defect status of the Optics layer has just changed. Varbind 'ifName' indicates the interface Name whose defect status of the Optics layer has just changed. Varbind 'coiOpticalControllerPortType' indicates the port type of the interface whose defect status of the Optics layer has just changed. Varbind 'coiOpticalControllerStatus' indicates the current defect status of the Optics layer on the interface.
Status: current Access: read-only
NOTIFICATION-TYPE    

coiOpticalEquipmentAlarm 1.3.6.1.4.1.9.9.828.0.2
This notification is generated whenever the optical equipment alarm is generated. Varbind 'coiOpticalAlarmLocation' indicates the location on which equipment failed alarm has generated. Varbind 'coiOpticalAlarmType' indicates the type of alarm. Varbind 'coiOpticalAlarmTimeStamp' indicates the timestamp when alarm is generated. Varbind 'coiOpticalAlarmName' indicates the alarm object. Varbind 'coiOpticalAlarmAdditionalInfo' indicates additional info related to the alarm. Varbind 'coiOpticalAlarmSeverity' indicates the severity of the alarm. Varbind 'coiOpticalAlarmStatus' indicates status of the alarm. Varbind 'coiOpticalAlarmServiceAffecting' indicates the service affected state when alarm is generated.
Status: current Access: read-only
NOTIFICATION-TYPE    

coiOpticalController 1.3.6.1.4.1.9.9.828.1.1
OBJECT IDENTIFIER    

coiOpticalPerformanceMonitoring 1.3.6.1.4.1.9.9.828.1.2
OBJECT IDENTIFIER    

coiOpticalNotifEnabled 1.3.6.1.4.1.9.9.828.1.1.1
This object controls the generation of coiOpticsStatusChange notification. If the value of this object is 'true', then the generation of coiOpticsStatusChange notification is enabled. If the value of this object is 'false', then the generation of coiOpticsStatusChange notification is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOpticalControllerTable 1.3.6.1.4.1.9.9.828.1.1.2
This table provides management information for optical layer related attributes of interfaces with an ifType of opticalChannel(195).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOpticalControllerEntry

coiOpticalControllerEntry 1.3.6.1.4.1.9.9.828.1.1.2.1
An entry containing management information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CoiOpticalControllerEntry  

coiOpticalControllerWavelength 1.3.6.1.4.1.9.9.828.1.1.2.1.1
This object is used to configure the wavelength on optical channel interfaces in 1/100 nm.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalWavelength  

coiOpticalControllerLaserStatus 1.3.6.1.4.1.9.9.828.1.1.2.1.2
This object gives the current operational state of the Laser. Valid values are - 'up' - The laser is operational. 'down' - The laser is not operational.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

coiOpticalControllerFrequency 1.3.6.1.4.1.9.9.828.1.1.2.1.3
This object is used to configure the frequency on optical channel interfaces in 100 MHz.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

coiOpticalControllerChannelNumber 1.3.6.1.4.1.9.9.828.1.1.2.1.4
This object is used to configure the channel number on optical channel interfaces. Channel Number is set to 0 if not 50GHz grid.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

coiOpticalControllerTransmitPower 1.3.6.1.4.1.9.9.828.1.1.2.1.5
This object is used to configure the Transmit Power in 1/100 dBm on optical channel interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOpticalControllerOpticsType 1.3.6.1.4.1.9.9.828.1.1.2.1.6
This object gives the description of optics present on optical channel interfaces.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

coiOpticalControllerRXLowThreshold 1.3.6.1.4.1.9.9.828.1.1.2.1.7
This object is used to configure the Receive Low Threshold in 1/100 dBm on optical channel interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOpticalControllerTXLowThreshold 1.3.6.1.4.1.9.9.828.1.1.2.1.8
This object is used to configure the Transmit Low Threshold in 1/100 dBm on optical channel interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOpticalControllerRXHighThreshold 1.3.6.1.4.1.9.9.828.1.1.2.1.9
This object is used to configure the Receive High Threshold in 1/100 dBm on optical channel interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOpticalControllerTXHighThreshold 1.3.6.1.4.1.9.9.828.1.1.2.1.10
This object is used to configure the Transmit High Threshold in 1/100 dBm on optical channel interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOpticalControllerLBCHighThreshold 1.3.6.1.4.1.9.9.828.1.1.2.1.11
This object is used to configure the Laser Bias Current High Threshold in 1/10% on optical channel interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1000  

coiOpticalControllerStatus 1.3.6.1.4.1.9.9.828.1.1.2.1.12
This object indicates the current defect status of the Optics layer. noDefect(0): No Defect. This bit is set high when no defect is detected on the optics. improprmvl(1): Improper Removal. This will be set when a physical pluggable is absent on a service (hw-module) provisioned port. mea(2): This bit will be set when Port Pluggable Module Mismatches With Pre-Provisoned PPM. provMismatch(3): Provision Mismatch. This bit is set when Provisioned wavelength is Not supported By Pluggable. highRXPwr(4): High Receive Power. This bit is set when the measured optical power of the received signal exceeds the threshold high value, which is user-provisionable. highTXPwr(5): High Transmit Power. This bit is set when Pluggable measured optical power of the transmitted signal falls over the threshold. lowRXPwr(6): Low Receive Power. This bit is set when the measured optical power of the received signal falls below the low threshold value, which is user-provisionable. lowTXPwr(7): Low Transmit Power. This bit is set when Pluggable measured optical power of the transmitted signal falls below the low threshold. highLBC(8): High Laser Bias. This bit is set when the Physical Pluggable Port laser reads laser bias value beyond configured high threshold. highDGD(9): High DGD. This bit is set when the pluggable port Module reads the Differential Group delay value that exceeds the configured high threshold. outOfRangeCD(10): Out of Range Chromatic Dispersion. This bit is set when the Chromatic dispersion value read by the associated HW is out of range with the configured threshold. lowOSNR(11): Low Optical Signal to Noise Ratio. This bit is set when the HW read Optical Signal to Noise ratio falls below the configured low threshold. wvlOutOfLock(12): Wavelength Out of Lock. This bit is set when Trunk Port optics detects that optical input frequency is out of range. highLaserTemp(13): High LaserTemp.This bit is set when the internally measured transceiver temperature exceeds the card setting by 35.6 degrees F or 2 degrees C. A laser temperature change affects the transmitted wavelength. lowLaserTemp(14): Low LaserTemp. This bit is set when the internally measured transceiver temperature falls below the card setting by 35.6 degrees F or 2 degrees C. A laser temperature change affects the transmitted wavelength. (This temperature is equivalent to about 200 picometers of wavelength. ppmFail(15): Pluggable Equipment Fail. This bit is set when Pluggable Equipment is not operational or manageable. This object is sent out as a notification to the agent.
Status: current Access: read-only
OBJECT-TYPE    
  BITS noDefect(0), improprmvl(1), mea(2), provMismatch(3), highRXPwr(4), highTXPwr(5), lowRXPwr(6), lowTXPwr(7), highLBC(8), highDGD(9), outOfRangeCD(10), lowOSNR(11), wvlOutOfLock(12), highLaserTemp(13), lowLaserTemp(14), ppmFail(15)  

coiOpticalControllerPortType 1.3.6.1.4.1.9.9.828.1.1.2.1.13
This object gives the port type of the optical interface.
Status: current Access: read-only
OBJECT-TYPE    
  CoiPortType  

coiOpticalControllerTotalRXPower 1.3.6.1.4.1.9.9.828.1.1.2.1.14
This object is used to configure the total receive power in 1/100 dBm on optical channel interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOpticalControllerTotalTXPower 1.3.6.1.4.1.9.9.828.1.1.2.1.15
This object is used to configure the total transmit power in 1/100 dBm on optical channel interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOpticalControllerPerLaneTable 1.3.6.1.4.1.9.9.828.1.1.3
This table provides the management information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) and lane number as coiOpticalControllerLane.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOpticalControllerPerLaneEntry

coiOpticalControllerPerLaneEntry 1.3.6.1.4.1.9.9.828.1.1.3.1
An entry containing management information on optical layer related attributes of interfaces with an ifType opticalChannel(195) and lane number as coiOpticalControllerLane. Entries are created by the feature when a new interface is added to the ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CoiOpticalControllerPerLaneEntry  

coiOpticalControllerLane 1.3.6.1.4.1.9.9.828.1.1.3.1.1
This object specifies the lane number for the optical controller. Each optical controller is divided into data lanes, with each lane operating at some data rate, giving an aggregated bandwidth of the controller, as a whole. Lane is applicable for breakout mode of operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

coiOpticalControllerPerLaneRXPower 1.3.6.1.4.1.9.9.828.1.1.3.1.2
This object specifies the Receive power in 1/100 dBm.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOpticalControllerPerLaneTXPower 1.3.6.1.4.1.9.9.828.1.1.3.1.3
This object specifies the Transmit power in 1/100 dBm.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOpticalControllerPerLaneLBC 1.3.6.1.4.1.9.9.828.1.1.3.1.4
This object specifies the Laser Bias Current in 1/10%.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1000  

coiOpticalControllerPerLaneOSNR 1.3.6.1.4.1.9.9.828.1.1.3.1.5
This object specifies the Optical Signal to Noise Ratio in 1/100 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOpticalControllerPerLaneChromaticDispersion 1.3.6.1.4.1.9.9.828.1.1.3.1.6
This object specifies the measure of spread of light pulse in ps/nm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOpticalControllerPerLaneDifferentialGroupDelay 1.3.6.1.4.1.9.9.828.1.1.3.1.7
This object specifies the propagation time difference between eigenmodes X and Y in 1/100 ps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOpticalControllerPerLaneSecondOrderPMD 1.3.6.1.4.1.9.9.828.1.1.3.1.8
This object specifies the threshold Second Order Polarization Mode Dispersion in 1/100 ps^2.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOpticalControllerPerLanePolarizationDependentLoss 1.3.6.1.4.1.9.9.828.1.1.3.1.9
This object specifies the threshold Polarization Dependent Loss in 1/100 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOpticalControllerPerLanePolarizationChangeRate 1.3.6.1.4.1.9.9.828.1.1.3.1.10
This object specifies the Polarization Change Rate in 1/100 rad/s.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOpticalControllerPerLanePhaseNoise 1.3.6.1.4.1.9.9.828.1.1.3.1.11
This object specifies the Fluctuations in the Phase of a Waveform in 1/1000 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOpticalClientInfoTable 1.3.6.1.4.1.9.9.828.1.3
This table provides management information for optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6).This parameter is applicable only for client interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOpticalClientInfoEntry

coiOpticalClientInfoEntry 1.3.6.1.4.1.9.9.828.1.3.1
An entry containing information for optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6). Entries are created by the feature when the interface discovers the neighbour's ethernet MAC Address.
Status: current Access: not-accessible
OBJECT-TYPE    
  CoiOpticalClientInfoEntry  

coiOpticalClientEthernetNeighbourMAC 1.3.6.1.4.1.9.9.828.1.3.1.1
This object gives the neighbour MAC Address to which the interface is connected.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

coiOpticalThresholdTable 1.3.6.1.4.1.9.9.828.1.2.1
This table provides threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) and Interval type as coiOptThreshIntervalType.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOpticalThresholdEntry

coiOpticalThresholdEntry 1.3.6.1.4.1.9.9.828.1.2.1.1
An entry containing threshold information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CoiOpticalThresholdEntry  

coiOptThreshIntervalType 1.3.6.1.4.1.9.9.828.1.2.1.1.1
This object gives the interval type during which the performance statistics are accumulated for the interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  CoiIntervalType  

coiOptThreshTXPowerMin 1.3.6.1.4.1.9.9.828.1.2.1.1.2
This object is used to configure the threshold of minimum Transmit power for the interface in 1/100 dBm.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOptThreshRXPowerMin 1.3.6.1.4.1.9.9.828.1.2.1.1.3
This object is used to configure the threshold of minimum Receive power for the interface in 1/100 dBm.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOptThreshOSNRMin 1.3.6.1.4.1.9.9.828.1.2.1.1.4
This object is used to configure the threshold of minimum Optical Signal to Noise Ratio for the interface in 1/100 dB.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshChromaticDispersionMin 1.3.6.1.4.1.9.9.828.1.2.1.1.5
This object is used to configure the threshold of minimum measure of spread of light pulse for the interface in ps/nm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshDifferentialGroupDelayMin 1.3.6.1.4.1.9.9.828.1.2.1.1.6
This object is used to configure the threshold of minimum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshSecondOrderPMDMin 1.3.6.1.4.1.9.9.828.1.2.1.1.7
This object is used to configure the threshold of minimum Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshPolarizationDependentLossMin 1.3.6.1.4.1.9.9.828.1.2.1.1.8
This object is used to configure the threshold of minimum Polarization Dependent Loss for the interface in 1/100 dB.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshPolarizationChangeRateMin 1.3.6.1.4.1.9.9.828.1.2.1.1.9
This object is used to configure the threshold of minimum Polarization Change Rate for the interface in 1/100 rad/s.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshPhaseNoiseMin 1.3.6.1.4.1.9.9.828.1.2.1.1.10
This object is used to configure the threshold of minimum Fluctuations in the Phase of a Waveform for the interface in 1/1000 dB.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshLBCMin 1.3.6.1.4.1.9.9.828.1.2.1.1.11
This object is used to configure the threshold of minumum Laser Bias Current in 1/10%.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1000  

coiOptThreshTXPowerMax 1.3.6.1.4.1.9.9.828.1.2.1.1.12
This object is used to configure the threshold of maximum Transmit power for the interface in 1/100 dBm.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOptThreshRXPowerMax 1.3.6.1.4.1.9.9.828.1.2.1.1.13
This object is used to configure the threshold of maximum Receive power for the interface in 1/100 dBm.
Status: current Access: read-write
OBJECT-TYPE    
  CoiOpticalPower  

coiOptThreshOSNRMax 1.3.6.1.4.1.9.9.828.1.2.1.1.14
This object is used to configure the threshold of maximum Optical Signal to Noise Ratio for the interface in 1/100 dB.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshChromaticDispersionMax 1.3.6.1.4.1.9.9.828.1.2.1.1.15
This object is used to configure the threshold of maximum measure of spread of light pulse for the interface in ps/nm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshDifferentialGroupDelayMax 1.3.6.1.4.1.9.9.828.1.2.1.1.16
This object is used to configure the threshold of maximum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshSecondOrderPMDMax 1.3.6.1.4.1.9.9.828.1.2.1.1.17
This object is used to configure the threshold of maximum Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshPolarizationDependentLossMax 1.3.6.1.4.1.9.9.828.1.2.1.1.18
This object is used to configure the threshold of maximum Polarization Dependent Loss for the interface in 1/100 dB.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshPolarizationChangeRateMax 1.3.6.1.4.1.9.9.828.1.2.1.1.19
This object is used to configure the threshold of maximum Polarization Change Rate in 1/100 rad/s for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshPhaseNoiseMax 1.3.6.1.4.1.9.9.828.1.2.1.1.20
This object is used to configure the threshold of maximum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

coiOptThreshLBCMax 1.3.6.1.4.1.9.9.828.1.2.1.1.21
This object is used to configure the threshold of maximum Laser Bias Current in 1/10 % for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1000  

coiOptThreshTXPowerEnableMin 1.3.6.1.4.1.9.9.828.1.2.1.1.22
This object is used to configure the enablement of threshold min Transmit power for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshRXPowerEnableMin 1.3.6.1.4.1.9.9.828.1.2.1.1.23
This object is used to configure the enablement of the threshold min Receive power for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshOSNREnableMin 1.3.6.1.4.1.9.9.828.1.2.1.1.24
This object is used to configure the enablement of the threshold min Optical Signal to Noise Ratio for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshChromaticDispersionEnableMin 1.3.6.1.4.1.9.9.828.1.2.1.1.25
This object is used to configure the enablement of the threshold min measure of spread of light pulse for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshDifferentialGroupDelayEnableMin 1.3.6.1.4.1.9.9.828.1.2.1.1.26
This object is used to configure the enablement of the threshold min propagation time difference between eigenmodes X and Y for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshSecondOrderPMDEnableMin 1.3.6.1.4.1.9.9.828.1.2.1.1.27
This object is used to configure the enablement of the threshold min Second Order Polarization Mode Dispersion for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshPolarizationDependentLossEnableMin 1.3.6.1.4.1.9.9.828.1.2.1.1.28
This object is used to configure the enablement of the threshold min Polarization Dependent Loss for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshPolarizationChangeRateEnableMin 1.3.6.1.4.1.9.9.828.1.2.1.1.29
This object is used to configure the enablement of the threshold min Polarization Change Rate for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshPhaseNoiseEnableMin 1.3.6.1.4.1.9.9.828.1.2.1.1.30
This object is used to configure the enablement of the threshold min Fluctuations in the Phase of a Waveform for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshLBCEnableMin 1.3.6.1.4.1.9.9.828.1.2.1.1.31
This object is used to configure the enablement of the threshold min Laser Bias Current for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshTXPowerEnableMax 1.3.6.1.4.1.9.9.828.1.2.1.1.32
This object is used to configure the enablement of the threshold max Transmit power for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshRXPowerEnableMax 1.3.6.1.4.1.9.9.828.1.2.1.1.33
This object is used to configure the enablement of the threshold max Receive power for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshOSNREnableMax 1.3.6.1.4.1.9.9.828.1.2.1.1.34
This object is used to configure the enablement of the threshold max Optical Signal to Noise Ratio for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshChromaticDispersionEnableMax 1.3.6.1.4.1.9.9.828.1.2.1.1.35
This object is used to configure the enablement of the threshold max measure of spread of light pulse for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshDifferentialGroupDelayEnableMax 1.3.6.1.4.1.9.9.828.1.2.1.1.36
This object is used to configure the enablement of the threshold max propagation time difference between eigenmodes X and Y for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshSecondOrderPMDEnableMax 1.3.6.1.4.1.9.9.828.1.2.1.1.37
This object is used to configure the enablement of the threshold max Second Order Polarization Mode Dispersion for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshPolarizationDependentLossEnableMax 1.3.6.1.4.1.9.9.828.1.2.1.1.38
This object is used to configure the enablement of the threshold max Polarization Dependent Loss for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshPolarizationChangeRateEnableMax 1.3.6.1.4.1.9.9.828.1.2.1.1.39
This object is used to configure the enablement of the threshold max Polarization Change Rate for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshPhaseNoiseEnableMax 1.3.6.1.4.1.9.9.828.1.2.1.1.40
This object is used to configure the enablement of the threshold max Fluctuations in the Phase of a Waveform for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOptThreshLBCEnableMax 1.3.6.1.4.1.9.9.828.1.2.1.1.41
This object is used to configure the enablement of the threshold max Laser Bias Current for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

coiOpticalCurrentTable 1.3.6.1.4.1.9.9.828.1.2.2
This table provides current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195), Lane as coiOptCurrentLane and Interval as coiOptCurrentIntervalType.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOpticalCurrentEntry

coiOpticalCurrentEntry 1.3.6.1.4.1.9.9.828.1.2.2.1
An entry containing current information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CoiOpticalCurrentEntry  

coiOptCurrentLane 1.3.6.1.4.1.9.9.828.1.2.2.1.1
This object specifies the lane number for the optical interface. Each optical controller is divided into data lanes with each lane operating at some data rate, giving an aggregated bandwidth of the controller as a whole. Lane is applicable for breakout mode of operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

coiOptCurrentIntervalType 1.3.6.1.4.1.9.9.828.1.2.2.1.2
This object gives the interval type during which the current performance statistics are accumulated.
Status: current Access: not-accessible
OBJECT-TYPE    
  CoiIntervalType  

coiOptCurrentTXPowerMax 1.3.6.1.4.1.9.9.828.1.2.2.1.3
This object specifies the current max Transmit power for the interface in 1/100 dBm.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptCurrentRXPowerMax 1.3.6.1.4.1.9.9.828.1.2.2.1.4
This object specifies the current max Receive power for the interface in 1/100 dBm.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptCurrentOSNRMax 1.3.6.1.4.1.9.9.828.1.2.2.1.5
This object specifies the current max Optical Signal to Noise Ratio for the interface in 1/100 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentChromaticDispersionMax 1.3.6.1.4.1.9.9.828.1.2.2.1.6
This object specifies the current max measure of spread of light pulse for the interface in ps/nm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentDifferentialGroupDelayMax 1.3.6.1.4.1.9.9.828.1.2.2.1.7
This object specifies the current max propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentSecondOrderPMDMax 1.3.6.1.4.1.9.9.828.1.2.2.1.8
This object specifies the current max Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentPolarizationDependentLossMax 1.3.6.1.4.1.9.9.828.1.2.2.1.9
This object specifies the current max Polarization Dependent Loss for the interface in 1/100 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentPolarizationChangeRateMax 1.3.6.1.4.1.9.9.828.1.2.2.1.10
This object specifies the current max Polarization Change Rate for the interface in 1/100 rad/s.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentPhaseNoiseMax 1.3.6.1.4.1.9.9.828.1.2.2.1.11
This object specifies the current max Fluctuations in the Phase of a Waveform for the interface in 1/1000 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentLBCMax 1.3.6.1.4.1.9.9.828.1.2.2.1.12
This object specifies the current max Laser Bias Current in 1/10% for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1000  

coiOptCurrentTXPowerMin 1.3.6.1.4.1.9.9.828.1.2.2.1.13
This object specifies the current min Transmit power for the interface in 1/100 dBm.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptCurrentRXPowerMin 1.3.6.1.4.1.9.9.828.1.2.2.1.14
This object specifies the current min Receive power for the interface in 1/100 dBm.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptCurrentOSNRMin 1.3.6.1.4.1.9.9.828.1.2.2.1.15
This object specifies the current min Optical Signal to Noise Ratio for the interface in 1/100 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentChromaticDispersionMin 1.3.6.1.4.1.9.9.828.1.2.2.1.16
This object specifies the current min measure of spread of light pulse for the interface in ps/nm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentDifferentialGroupDelayMin 1.3.6.1.4.1.9.9.828.1.2.2.1.17
This object specifies the current min propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentSecondOrderPMDMin 1.3.6.1.4.1.9.9.828.1.2.2.1.18
This object specifies the current min Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentPolarizationDependentLossMin 1.3.6.1.4.1.9.9.828.1.2.2.1.19
This object specifies the current min Polarization Dependent Loss for the interface in 1/100 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentPolarizationChangeRateMin 1.3.6.1.4.1.9.9.828.1.2.2.1.20
This object specifies the current min Polarization Change Rate for the interface in 1/100 rad/s.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentPhaseNoiseMin 1.3.6.1.4.1.9.9.828.1.2.2.1.21
This object specifies the current min Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentLBCMin 1.3.6.1.4.1.9.9.828.1.2.2.1.22
This object specifies the current min Laser Bias Current in 1/10% for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1000  

coiOptCurrentTXPowerAvg 1.3.6.1.4.1.9.9.828.1.2.2.1.23
This object specifies the current average Transmit power for the interface in 1/100 dBm.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptCurrentRXPowerAvg 1.3.6.1.4.1.9.9.828.1.2.2.1.24
This object specifies the current average Receive power for the interface in 1/100 dBm.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptCurrentOSNRAvg 1.3.6.1.4.1.9.9.828.1.2.2.1.25
This object specifies the current average Optical Signal to Noise Ratio for the interface in 1/100 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentChromaticDispersionAvg 1.3.6.1.4.1.9.9.828.1.2.2.1.26
This object specifies the current average measure of spread of light pulse for the interface in ps/nm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentDifferentialGroupDelayAvg 1.3.6.1.4.1.9.9.828.1.2.2.1.27
This object specifies the current average propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentSecondOrderPMDAvg 1.3.6.1.4.1.9.9.828.1.2.2.1.28
This object specifies the current average Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentPolarizationDependentLossAvg 1.3.6.1.4.1.9.9.828.1.2.2.1.29
This object specifies the current average Polarization Dependent Loss for the interface in 1/100 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentPolarizationChangeRateAvg 1.3.6.1.4.1.9.9.828.1.2.2.1.30
This object specifies the current average Polarization Change Rate for the interface in 1/100 rad/s.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentPhaseNoiseAvg 1.3.6.1.4.1.9.9.828.1.2.2.1.31
This object specifies the current average Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptCurrentLBCAvg 1.3.6.1.4.1.9.9.828.1.2.2.1.32
This object specifies the current average Laser Bias Current in 1/10% for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..1000  

coiOptCurrentTimestamp 1.3.6.1.4.1.9.9.828.1.2.2.1.33
This object specifies the timestamp for the current bucket for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

coiOpticalIntervalTable 1.3.6.1.4.1.9.9.828.1.2.3
This table provides interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195), lane as coiOptIntervalLane, Interval as coiOptIntervalIntervalType and history bucket as coiOptIntervalIntervalType.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CoiOpticalIntervalEntry

coiOpticalIntervalEntry 1.3.6.1.4.1.9.9.828.1.2.3.1
An entry containing interval information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CoiOpticalIntervalEntry  

coiOptIntervalLane 1.3.6.1.4.1.9.9.828.1.2.3.1.1
This object specifies the lane number for the optical interface. Each optical controller is divided into data lanes with each lane operating at some data rate, giving an aggregated bandwidth of the controller as a whole.Lane is applicable for breakout mode of operation.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..12  

coiOptIntervalIntervalType 1.3.6.1.4.1.9.9.828.1.2.3.1.2
This object gives the interval type during which the performance statistics are accumulated.
Status: current Access: not-accessible
OBJECT-TYPE    
  CoiIntervalType  

coiOptIntervalNum 1.3.6.1.4.1.9.9.828.1.2.3.1.3
This object identifies the interval for which the set of interval performance values is available. The interval identified by 1 is the most recent 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..32  

coiOptIntervalTXPowerMax 1.3.6.1.4.1.9.9.828.1.2.3.1.4
This object specifies the interval maximum Transmit power in 1/100 dBm for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptIntervalRXPowerMax 1.3.6.1.4.1.9.9.828.1.2.3.1.5
This object specifies the interval maximum Receive power in 1/100 dBm for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptIntervalOSNRMax 1.3.6.1.4.1.9.9.828.1.2.3.1.6
This object specifies the interval maximum Optical Signal to Noise Ratio in 1/100 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalChromaticDispersionMax 1.3.6.1.4.1.9.9.828.1.2.3.1.7
This object specifies the interval maximum measure of spread of light pulse for the interface in ps/nm.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalDifferentialGroupDelayMax 1.3.6.1.4.1.9.9.828.1.2.3.1.8
This object specifies the interval maximum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalSecondOrderPMDMax 1.3.6.1.4.1.9.9.828.1.2.3.1.9
This object specifies the interval maximum Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalPolarizationDependentLossMax 1.3.6.1.4.1.9.9.828.1.2.3.1.10
This object specifies the interval maximum Polarization Dependent Loss in 1/100 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalPolarizationChangeRateMax 1.3.6.1.4.1.9.9.828.1.2.3.1.11
This object specifies the interval maximum Polarization Change Rate in 1/100 rad/s for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalPhaseNoiseMax 1.3.6.1.4.1.9.9.828.1.2.3.1.12
This object specifies the interval maximum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalLBCMax 1.3.6.1.4.1.9.9.828.1.2.3.1.13
This object specifies the interval maximum Laser Bias Current in 1/10% for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalTXPowerMin 1.3.6.1.4.1.9.9.828.1.2.3.1.14
This object specifies the interval minimum Transmit power in 1/100 dBm for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptIntervalRXPowerMin 1.3.6.1.4.1.9.9.828.1.2.3.1.15
This object specifies the interval minimum Receive power in 1/100 dBm for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptIntervalOSNRMin 1.3.6.1.4.1.9.9.828.1.2.3.1.16
This object specifies the interval minimum Optical Signal to Noise Ratio in 1/100 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalChromaticDispersionMin 1.3.6.1.4.1.9.9.828.1.2.3.1.17
This object specifies the interval minimum measure of spread of light pulse in ps/nm for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalDifferentialGroupDelayMin 1.3.6.1.4.1.9.9.828.1.2.3.1.18
This object specifies the interval minimum propagation time difference between eigenmodes X and Y in 1/100 ps for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalSecondOrderPMDMin 1.3.6.1.4.1.9.9.828.1.2.3.1.19
This object specifies the interval minimum Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalPolarizationDependentLossMin 1.3.6.1.4.1.9.9.828.1.2.3.1.20
This object specifies the interval minimum Polarization Dependent Loss in 1/100 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalPolarizationChangeRateMin 1.3.6.1.4.1.9.9.828.1.2.3.1.21
This object specifies the interval minimum Polarization Change Rate in 1/100 rad/s for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalPhaseNoiseMin 1.3.6.1.4.1.9.9.828.1.2.3.1.22
This object specifies the interval minimum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalLBCMin 1.3.6.1.4.1.9.9.828.1.2.3.1.23
This object specifies the interval minimum Laser Bias Current in 1/10% for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalTXPowerAvg 1.3.6.1.4.1.9.9.828.1.2.3.1.24
This object specifies the interval average Transmit power in 1/100 dBm for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptIntervalRXPowerAvg 1.3.6.1.4.1.9.9.828.1.2.3.1.25
This object specifies the interval average Receive power in 1/100 dBm for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  CoiOpticalPower  

coiOptIntervalOSNRAvg 1.3.6.1.4.1.9.9.828.1.2.3.1.26
This object specifies the interval average Optical Signal to Noise Ratio in 1/100 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalChromaticDispersionAvg 1.3.6.1.4.1.9.9.828.1.2.3.1.27
This object specifies the interval average measure of spread of light pulse in ps/nm for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalDifferentialGroupDelayAvg 1.3.6.1.4.1.9.9.828.1.2.3.1.28
This object specifies the interval average propagation time difference between eigenmodes X and Y in 1/100 ps for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalSecondOrderPMDAvg 1.3.6.1.4.1.9.9.828.1.2.3.1.29
This object specifies the interval average Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalPolarizationDependentLossAvg 1.3.6.1.4.1.9.9.828.1.2.3.1.30
This object specifies the interval average Polarization Dependent Loss in 1/100 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalPolarizationChangeRateAvg 1.3.6.1.4.1.9.9.828.1.2.3.1.31
This object specifies the interval average Polarization Change Rate in 1/100 rad/s for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalPhaseNoiseAvg 1.3.6.1.4.1.9.9.828.1.2.3.1.32
This object specifies the interval average Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalLBCAvg 1.3.6.1.4.1.9.9.828.1.2.3.1.33
This object specifies the interval average Laser Bias Current in 1/10 % for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

coiOptIntervalTimestamp 1.3.6.1.4.1.9.9.828.1.2.3.1.34
This object specifies the timestamp, for the bucket specified by 'coiOptIntervalNum', for the interface.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

coiOpticalEquipmentAlarmGroup 1.3.6.1.4.1.9.9.828.1.4
OBJECT IDENTIFIER    

coiOpticalAlarmLocation 1.3.6.1.4.1.9.9.828.1.4.1
This object indicates the location of the component that raised alarm, within the device.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

coiOpticalAlarmType 1.3.6.1.4.1.9.9.828.1.4.2
This object indicates the type of alarm that is raised.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CoiOptAlarmType  

coiOpticalAlarmTimeStamp 1.3.6.1.4.1.9.9.828.1.4.3
This object gives the time when an event occurred. This is accurate only upto a second.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TimeStamp  

coiOpticalAlarmName 1.3.6.1.4.1.9.9.828.1.4.4
This variable gives the user-visible name, which uniquely identifies the alarm in the system.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

coiOpticalAlarmAdditionalInfo 1.3.6.1.4.1.9.9.828.1.4.5
This variable provides additional info about the alarm. This object would be a null string if no additional information is specified.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

coiOpticalAlarmSeverity 1.3.6.1.4.1.9.9.828.1.4.6
This variable specifies alarm severity.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CoiOptAlarmSeverity  

coiOpticalAlarmStatus 1.3.6.1.4.1.9.9.828.1.4.7
This variable specifies alarm status.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CoiOptAlarmStatus  

coiOpticalAlarmServiceAffecting 1.3.6.1.4.1.9.9.828.1.4.8
This variable specifies the service affecting state of the alarm.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  CoiOptAlarmServiceAffecting  

ciscoOpticalMIBConformance 1.3.6.1.4.1.9.9.828.2
OBJECT IDENTIFIER    

ciscoOpticalMIBCompliances 1.3.6.1.4.1.9.9.828.2.1
OBJECT IDENTIFIER    

ciscoOpticalMIBGroups 1.3.6.1.4.1.9.9.828.2.2
OBJECT IDENTIFIER    

ciscoOpticalMIBCompliance 1.3.6.1.4.1.9.9.828.2.1.1
The compliance statement for platforms that monitor the parameters for the optical interfaces.
Status: deprecated Access: accessible-for-notify
MODULE-COMPLIANCE    

ciscoOpticalMIBComplianceRev1 1.3.6.1.4.1.9.9.828.2.1.2
The compliance statement for platforms that monitor the parameters for the optical interfaces.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

coiOpticalGroup 1.3.6.1.4.1.9.9.828.2.2.1
The collection of objects to give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

coiOpticalControllerGroup 1.3.6.1.4.1.9.9.828.2.2.2
The collection of objects to allow configurations and give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

coiOpticalControllerPerLaneGroup 1.3.6.1.4.1.9.9.828.2.2.3
The collection of objects to give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195) and lane number as coiOpticalControllerLane.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

coiOpticalClientInfoGroup 1.3.6.1.4.1.9.9.828.2.2.4
The collection of objects to give information related to optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

coiOpticalThresholdGroup 1.3.6.1.4.1.9.9.828.2.2.5
The collection of objects used for monitoring the threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195).
Status: current Access: accessible-for-notify
OBJECT-GROUP    

coiOpticalCurrentGroup 1.3.6.1.4.1.9.9.828.2.2.6
The collection of objects used for monitoring the current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) in a current interval.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

coiOpticalIntervalGroup 1.3.6.1.4.1.9.9.828.2.2.7
The collection of objects used for monitoring the interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) in a given interval.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

coiOpticalNotifEnableGroup 1.3.6.1.4.1.9.9.828.2.2.8
The collection of objects to enable the notification generations upon an interface's defect status change on optics layer.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

coiOpticalNotifStatusObjectGroup 1.3.6.1.4.1.9.9.828.2.2.9
The object to be included in an Optical interface's defect status change notification.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

coiOpticalNotifGroup 1.3.6.1.4.1.9.9.828.2.2.10
The optical status change notifications whenever the defect status of optical layer on an interface changes.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

coiOpticalEquipmentAlarmInfoGroup 1.3.6.1.4.1.9.9.828.2.2.11
The optical equipment notifications whenever the alarm is generated.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

coiOpticalPowerGroup 1.3.6.1.4.1.9.9.828.2.2.12
The collection of objects used for monitoring the total power information for optical layer related attributes of interfaces with an ifType of opticalChannel(195).
Status: current Access: accessible-for-notify
OBJECT-GROUP