CISCO-MGX82XX-RPM-CONN-MIB
File:
CISCO-MGX82XX-RPM-CONN-MIB.mib (19703 bytes)
Imported modules
Imported symbols
Defined Types
| RpmNsapAddress |
|
| ATM address used by the networking entity. The only
address type presently supported is NSAP (20 octets) |
| TEXTUAL-CONVENTION |
|
|
|
| |
OCTET STRING |
Size(20) |
|
| RpmChanGrpEntry |
|
| SEQUENCE |
|
|
|
| |
rpmChanSlotNum |
Integer32 |
|
| |
rpmChanInterface |
Integer32 |
|
| |
rpmChanNum |
Integer32 |
|
| |
rpmChanRowStatus |
INTEGER |
|
| |
rpmChanVcd |
Integer32 |
|
| |
rpmChanVpi |
Integer32 |
|
| |
rpmChanVci |
Integer32 |
|
| |
rpmChanSubInterface |
Integer32 |
|
| |
rpmChanLocalVpi |
Integer32 |
|
| |
rpmChanLocalVci |
Integer32 |
|
| |
rpmChanLocalNsap |
RpmNsapAddress |
|
| |
rpmChanRemoteVpi |
Integer32 |
|
| |
rpmChanRemoteVci |
Integer32 |
|
| |
rpmChanRemoteNsap |
RpmNsapAddress |
|
| |
rpmChanType |
INTEGER |
|
| |
rpmChanConnType |
INTEGER |
|
| |
rpmChanServiceType |
INTEGER |
|
| |
rpmChanMastership |
INTEGER |
|
| |
rpmChanRtePriority |
Integer32 |
|
| |
rpmChanMaxCost |
Integer32 |
|
| |
rpmChanRestrictTrkType |
INTEGER |
|
| |
rpmChanPCR |
Integer32 |
|
| |
rpmChanRemotePCR |
Integer32 |
|
| |
rpmChanMCR |
Integer32 |
|
| |
rpmChanRemoteMCR |
Integer32 |
|
| |
rpmChanPercentUtil |
Integer32 |
|
| |
rpmChanRemotePercentUtil |
Integer32 |
|
| |
rpmChanMidLow |
Integer32 |
|
| |
rpmChanMidHigh |
Integer32 |
|
| |
rpmChanBurstSize |
Integer32 |
|
| |
rpmChanEncapType |
INTEGER |
|
| |
rpmChanInArpFreq |
Integer32 |
|
| |
rpmChanOAMloopback |
Integer32 |
|
| |
rpmChanState |
INTEGER |
|
| |
rpmChanVirtualTemplate |
Integer32 |
|
| |
rpmChanAbrRDF |
Integer32 |
|
| |
rpmChanAbrRIF |
Integer32 |
|
Defined Values
| ciscoMgx82xxRpmConnMIB |
1.3.6.1.4.1.351.150.62 |
| The connection MIB module for RPM(Router Blade)
service module in MGX8250/MGX8230 products.
The 'channel' and 'connection' and 'connection endpoint'
mean same in this MIB. |
| MODULE-IDENTITY |
|
|
|
| rpmChanGrpTable |
1.3.6.1.4.1.351.110.5.2.10.1.1 |
| This table contains endpoint configuration
information for connections applicable to
RPM service module. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
RpmChanGrpEntry |
|
| rpmChanGrpEntry |
1.3.6.1.4.1.351.110.5.2.10.1.1.1 |
| An entry for logical channel. Each entry
corresponds to a connection endpoint identified
by Slot number and channel number. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
RpmChanGrpEntry |
|
|
| rpmChanSlotNum |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.1 |
| Specifies the slot number of the RPM card. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..30 |
|
| rpmChanInterface |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.2 |
| This is the RPM's backplane interface.
Currently there is only one interface. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| rpmChanNum |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.3 |
| This object identifies the channel number.
This is also called Logical Connection Number(LCN).
This is a unique number which identifies a
connection.
The LCN maps VPI and VCI.
For VCC, VCI range is 1..3825, and LCN range is 16..3840.
LCN = VCI + 16.
For VPC, VPI range is 1..255 and LCN range is 3841..4095.
LCN = VPI + 3840. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
16..4095 |
|
| rpmChanRowStatus |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.4 |
| This indicates the status of this channel.
add(1) : Channel is added.
del(2) : channel is deleted.
mod(3) : Set to this value before modifying objects
related to connection endpoints. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
add(1), del(2), mod(3) |
|
| rpmChanVcd |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.5 |
| Virtual Circuit Descriptor. A unique number
which identifies a connection. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..4095 |
|
| rpmChanVpi |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.6 |
| The VPI value for this channel.
For VPC, VPI range is 1..255 and
LCN range is 3841..4095.
LCN = VPI + 3840 |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..255 |
|
| rpmChanVci |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.7 |
| The VCI value for this channel.
For VCC, VCI range is 1..3825, and
LCN range is 16..3840.
LCN = VCI + 16. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..65535 |
|
| rpmChanSubInterface |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.8 |
| This is the RPM's backplane sub-interface. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..2147483647 |
|
| rpmChanLocalVpi |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.9 |
| This VPI together with the local VCI
and NSAP represents the local end point
in this connection. The VPI value is zero for
rpmChanConnType value of vcc(2). |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..255 |
|
| rpmChanLocalVci |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.10 |
| This VCI together with the local
VPI and NSAP represents the local
end point in this connection. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..65535 |
|
| rpmChanLocalNsap |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.11 |
| This object identifies the local NSAP address.
The bytes are mapped as follows:
prefix : 13 bytes
Cisco ID : 2 bytes
Reserved : 2 bytes
Slot/Port : 2 bytes[5 bit slot, 11 bits port]
Selector : 1 byte.
Of the 13 bytes for the node name, only the first
8 bytes are used. If the node name is n
(0 < n < 8) bytes long, the node name must be left
justified ( Bytes 1 to n contain the node name
and bytes (n+1) to 8 must be 0 ).
Bytes 9-13 must be always 0. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
RpmNsapAddress |
|
|
| rpmChanRemoteVpi |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.12 |
| This VPI together with the remote
VCI and NSAP represents the remote
end point in this connection. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..255 |
|
| rpmChanRemoteVci |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.13 |
| This VCI together with the remote
VPI and NSAP represents the remote
end point in this connection. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..65535 |
|
| rpmChanRemoteNsap |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.14 |
| This object identifies the remote NSAP address.
The bytes are mapped as follows:
prefix : 13 bytes
Cisco ID : 2 bytes
Reserved : 2 bytes
Slot/Port : 2 bytes[5 bit slot, 11 bits port]
Selector : 1 byte. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
RpmNsapAddress |
|
|
| rpmChanType |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.15 |
| This object identifies the channel type
svc(1) : Switched Virtual Connection
pvc(2) : Permanent Virtual Connection
spvc(3) : Soft PVC. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
svc(1), pvc(2), spvc(3) |
|
| rpmChanConnType |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.16 |
| This specifies the connection type
vpc(1) : Virtual Path Connection
vcc(1) : Virtual Channel Connection |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
vpc(1), vcc(2) |
|
| rpmChanServiceType |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.17 |
| This object identifies the connection service type.
cbr (1) : Constant Bit Rate
vbr (2) : Variable Bit Rate
ubr (4) : Unspecified Bit Rate
atfr (5) : ATM Frame Relay
abrstd (6) : Standard ABR
abrfst (7) : foresight ABR. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
cbr(1), vbr(2), ubr(4), atfr(5), abrstd(6), abrfst(7) |
|
| rpmChanMastership |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.18 |
| This specifies which end of the connection
is the master. This is used by PXM to determine
if this end point is master or slave. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
master(1), slave(2), unknown(3) |
|
| rpmChanRtePriority |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.19 |
| This is also known as class of service,
it is used by PXM to determine how important
this connection is when selecting connections
to route. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..15 |
|
| rpmChanMaxCost |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.20 |
| Maximum allowed cost. It is related to
Cost Based Routing. This is used by PXM so
that it won't choose a path with a cost
greater than this configured level. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..65535 |
|
| rpmChanRestrictTrkType |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.21 |
| Restricted trunk type for routing, used by PXM.
It specifies that the connection either cannot
be routed over satellite trunks or terrestrial
trunks, or it can be on any type of trunk. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
noRestriction(1), terrestrialTrunk(2), satelliteTrunk(3) |
|
| rpmChanPCR |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.22 |
| Peak cell rate.(in cells per sec.) |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..353208 |
|
| rpmChanRemotePCR |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.23 |
| Peak cell rate of the remote endpoint of
the connection. If not set, its value will
be same as the value of rpmChanPCR. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..353208 |
|
| rpmChanMCR |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.24 |
| Minimum cell rate.(in cells per sec.). |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..353208 |
|
| rpmChanRemoteMCR |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.25 |
| Minimum cell rate of the remote endpoint.
If this is not set, its value will be same
as value of rpmChanMCR. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..353208 |
|
| rpmChanPercentUtil |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.26 |
| This is the expected long-term utilization of the
channel by this end-point. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..100 |
|
| rpmChanRemotePercentUtil |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.27 |
| This is the expected long-term utilization of the
channel by the other end-point. If this is not
specified in the connection setup request,
it'll be set to be the same as the local end. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..100 |
|
| rpmChanEncapType |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.28 |
| This object identifies the ATM adaptation
layer (AAL) and Encapsulation type.
aal5snap - LLC/SNAP precedes the protocol datagram.
aal34smds - Encapsulation for SMDS network.
aal5nlpid - Encapsulation that allows ATM interfaces to
interoperate with HSSI.
qsaal - signaling type PVC used for setting up or
tearing down SVCs.
ilmi - used to set up communication with ILMI.
aal5mux[protocol] - a MUX-type Virtual circuit.
ppp - PPP over ATM.
The Encapsulation types aal34smds, qsaal and ilmi
are not supported. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
aal5snap(1), aal34smds(2), aal5nlpid(3), qsaal(4), ilmi(5), aal5muxXNS(6), aal5muxIP(7), aal5muxVINES(8), aal5muxDECNET(9), aal5muxNOVELL1(10), ppp(11), unknown(12) |
|
| rpmChanMidLow |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.29 |
| Starting Message Identifier Number for this PVC. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..1023 |
|
| rpmChanMidHigh |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.30 |
| Ending Message Identifier Number for this PVC. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..1023 |
|
| rpmChanBurstSize |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.31 |
| The Maximum number of ATM cells the
virtual circuit can transmit. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..65535 |
|
| rpmChanInArpFreq |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.32 |
| Specifies how often Inverse ARP datagrams
will be sent on this virtual circuit. The
value zero will disable the IN-ARP for this
channel. This object is supported only
for the value of rpmChanEncapType = aal5snap. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..60 |
|
| rpmChanOAMloopback |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.33 |
| This object specifies how often to generate
an OAM F5 loopback cell from this virtual circuit.
The value zero will disable generation of OAM F5
loopback cells. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
0..600 |
|
| rpmChanState |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.34 |
| This indicates the status of this channel.
1 ==> notConfigured
2 ==> active
3 ==> failed.
Currently 'failed' state is not supported.
When the channel is not added, the state is
notConfigured. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
notConfigured(1), active(2), failed(3) |
|
| rpmChanVirtualTemplate |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.35 |
| Specifies the Virtual Template used for CISCO PPP.
If it is not using Virtual Template then this value
is zero. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| rpmChanAbrRDF |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.36 |
| This is valid only for ABR Service Type.
Rate Decrease Factor: Controls the rate
decrease which occurs when backward RM-cells
with CI=1 are received. Larger values lead to
faster rate decrease. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| rpmChanAbrRIF |
1.3.6.1.4.1.351.110.5.2.10.1.1.1.37 |
| This is valid only for ABR Service Type.
Rate Increase Factor: Controls the rate
increase which occurs when a backward RM-cell
is received with CI=0 and NI=0. Larger values
lead to faster rate increase. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| cmrConnMIBCompliance |
1.3.6.1.4.1.351.150.62.2.1.1 |
| The compliance statement for the
Cisco MGX RPM connection management group. |
| Status: current |
Access: read-only |
| MODULE-COMPLIANCE |
|
|
|
| cmrConnConfGroup |
1.3.6.1.4.1.351.150.62.2.2.1 |
| The objects related to Connections on RPM
card. |
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|