CISCO-MEGACO-EXT-MIB

File: CISCO-MEGACO-EXT-MIB.mib (154768 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
INET-ADDRESS-MIB SNMP-FRAMEWORK-MIB CISCO-TC
CISCO-SMI CISCO-MGC-MIB CISCO-VOICE-COMMON-DIAL-CONTROL-MIB
CISCO-MEDIA-GATEWAY-MIB CISCO-ATM-TRUNK-MIB CISCO-IETF-MEGACO-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
TimeTicks Integer32 Gauge32
Counter32 TEXTUAL-CONVENTION TruthValue
RowStatus TimeStamp MODULE-COMPLIANCE
OBJECT-GROUP InetAddress InetAddressType
SnmpAdminString CiscoPort ciscoExperiment
CMgcGroupIndex CvcSpeechCoderRate CCallControlProfileIndex
CCallControlProfileIndexOrZero Counter32SinceReset cmedGatewayId
cmedGatewayLinkId cmedTerminationsEntry cmedGatewayConfigEntry
cmedGatewayStatsEntry

Defined Types

CH248Packages  
This textual convention defines all possible packages in H.248 protocol.
TEXTUAL-CONVENTION    
  BITS pkgG(0), pkgRoot(1), pkgToneGen(2), pkgToneDet(3), pkgDG(4), pkgDD(5), pkgCG(6), pkgCD(7), pkgCT(8), pkgNT(9), pkgRTP(10), pkgTDMC(11), pkgAN(12), pkgBCG(13), pkgXCG(14), pkgSrvTn(15), pkgXsrvTn(16), pkgChp(17), pkgIT(18), pkgLLTR(19), pkgBCAS(20), pkgRBS(21), pkgOSES(22), pkgAMET(23), pkgBCASAddr(24), pkgCASBlock(25), pkgGRI(26), rtcpxr(27), xrbm(28), qac(29), pkgDS(30), pkgETerm(31), pkgXnq(32), pkgCTYP(33), pkgIPFAX(34)  

CMedxCotTones  
This textual convention defines the tones to be used between originating gateway and terminating gateway in the COT (Continuity Test). co1 (1) - CO1 is either 2000Hz or 2010Hz depending on the region/country regulation. co2 (2) - CO2 is always 1780Hz.
TEXTUAL-CONVENTION    
  INTEGER co1(1), co2(2)  

CmedxGatewayConfigEntry  
SEQUENCE    
  cmedxGatewayMgcGroupIndex CMgcGroupIndex
  cmedxGatewayIpAddressIndex Unsigned32
  cmedxGatewayAssociationId Unsigned32
  cmedxGatewayMaxContexts Unsigned32
  cmedxGatewayMaxTermsInContext Unsigned32
  cmedxGatewayMgExecTime Unsigned32
  cmedxGatewayMgcExecTime Unsigned32
  cmedxGatewayProvisionRespTime Unsigned32
  cmedxGatewayNumConnRetries Unsigned32
  cmedxGatewayMaxWaitingDelay Unsigned32
  cmedxGatewayRestartDelay Unsigned32
  cmedxGatewayRespRetentionTime Unsigned32
  cmedxGatewayInitialRtt Unsigned32
  cmedxGatewayInactivityTime Unsigned32
  cmedxGatewayHeaderAddrType InetAddressType
  cmedxGatewayDownServiceDelay Integer32
  cmedxGatewayActiveMgcAddress InetAddress
  cmedxGatewayActiveMgcDomain SnmpAdminString
  cmedxGatewayActiveMgcPortNum CiscoPort
  cmedxGatewayStateChangeReason INTEGER
  cmedxGatewayStateChangeMethod INTEGER
  cmedxGatewayAdminAction INTEGER
  cmedxGatewayServiceState INTEGER
  cmedxGatewayDynamicTpktVersion TruthValue
  cmedxGatewayMaxCommandMsgSize Unsigned32
  cmedxGatewayMaxReplyMsgSize Unsigned32
  cmedxGatewaySctpAssocId Unsigned32
  cmedxGatewaySrvChgProfile SnmpAdminString
  cmedxGatewaySrvChgProfileVer Unsigned32
  cmedxGatewayMsgTokenType INTEGER
  cmedxGatewayMgProvisionRspTime Unsigned32
  cmedxGatewayMgcProvisionRspTime Unsigned32
  cmedxGatewayMgOrigPendLimit Unsigned32
  cmedxGatewayMgcOrigPendLimit Unsigned32
  cmedxGatewayDomainName SnmpAdminString
  cmedxGatewayCmbDnAndPortInMID TruthValue

CmedxTerminationTypeEntry  
SEQUENCE    
  cmedxTermTypeId Unsigned32
  cmedxTermType INTEGER
  cmedxTermTypeProfileId CCallControlProfileIndexOrZero
  cmedxTermTypePkgIds CH248Packages
  cmedxTermTypeRowStatus RowStatus

CmedxProfileEntry  
SEQUENCE    
  cmedxProfileIndex CCallControlProfileIndex
  cmedxProfilePlayCpToneInterDur Unsigned32
  cmedxProfileDtmfDigitOnDur Unsigned32
  cmedxProfileDtmfPauseDur Unsigned32
  cmedxProfileCot1Frequency Unsigned32
  cmedxProfileCot2Frequency Unsigned32
  cmedxProfileInitiateCotDur Unsigned32
  cmedxProfileRespCotMethod INTEGER
  cmedxProfileDetectLongCpToneDur Unsigned32
  cmedxProfileDetectLongDigitDur Unsigned32
  cmedxProfileEchoCancelEnabled TruthValue
  cmedxProfileEchoCancelTail INTEGER
  cmedxProfileInGainControl Integer32
  cmedxProfileOutAttnControl Unsigned32
  cmedxProfileVoIpVadEnabled TruthValue
  cmedxProfileVoIpVadTimer Unsigned32
  cmedxProfileVoAal2VadTimer Unsigned32
  cmedxProfileAtmBearerType INTEGER
  cmedxProfileAtmAalPartialFill Unsigned32
  cmedxProfileAtmAalType INTEGER
  cmedxProfileSuppressBearerDigit TruthValue
  cmedxProfileRowStatus RowStatus
  cmedxProfileOriginatingCotTx CMedxCotTones
  cmedxProfileOriginatingCotRx CMedxCotTones
  cmedxProfileTerminatingCotTx CMedxCotTones
  cmedxProfileTerminatingCotRx CMedxCotTones
  cmedxProfileComfortNoiseGenerate INTEGER

CmedxCallReduceControlEntry  
SEQUENCE    
  cmedxCallCongEnabled TruthValue
  cmedxCallRenotifInterval Unsigned32
  cmedxCRRNumOfLevel Unsigned32
  cmedxCurrentCRR Unsigned32
  cmedxCrrNotifyState TruthValue
  cmedxCrrNotifyEnabled OCTET STRING
  cmedxCurrentCallState INTEGER

CmedxCallReduceLevelEntry  
SEQUENCE    
  cmedxCallReduceLevelNum Unsigned32
  cmedxCallReduceRate Unsigned32

CmedxOverloadControlEntry  
SEQUENCE    
  cmedxOverloadControlEnabled TruthValue
  cmedxOverloadNotifyState TruthValue
  cmedxOverloadNotifyEnabled OCTET STRING

CmedxCodecNegotiationEntry  
SEQUENCE    
  cmedxCodecNegotiationCodec CvcSpeechCoderRate
  cmedxCodecNegotiationPreference Unsigned32

CmedxGatewayStatsEntry  
SEQUENCE    
  cmedxGatewayLastEvent Unsigned32

CmedxCommandStatsEntry  
SEQUENCE    
  cmedxCmdNumAddFails Counter32
  cmedxCmdNumAddSucceeds Counter32
  cmedxCmdNumSubtractFails Counter32
  cmedxCmdNumSubtractSucceeds Counter32
  cmedxCmdNumMoveFails Counter32
  cmedxCmdNumMoveSucceeds Counter32
  cmedxCmdNumModifyFails Counter32
  cmedxCmdNumModifySucceeds Counter32
  cmedxCmdNumAuditValFails Counter32
  cmedxCmdNumAuditValSucceeds Counter32
  cmedxCmdNumAuditCapFails Counter32
  cmedxCmdNumAuditCapSucceeds Counter32
  cmedxCmdNumNotifyFails Counter32
  cmedxCmdNumNotifySucceeds Counter32
  cmedxCmdNumSrvChgFromMgcFails Counter32
  cmedxCmdNumSrvChgFromMgcSucceeds Counter32
  cmedxCmdNumSrvChgFromMgFails Counter32
  cmedxCmdNumSrvChgFromMgSucceeds Counter32
  cmedxCmdTotalFails Counter32
  cmedxCmdTotalSucceeds Counter32
  cmedxCmdTotal Counter32
  cmedxCmdNumAddPendings Counter32
  cmedxCmdNumSubtractPendings Counter32
  cmedxCmdNumMovePendings Counter32
  cmedxCmdNumModifyPendings Counter32
  cmedxCmdNumAuditValPendings Counter32
  cmedxCmdNumAuditCapPendings Counter32
  cmedxCmdNumNotifyPendings Counter32
  cmedxCmdNumSrvChgFromMgcPendings Counter32
  cmedxCmdNumSrvChgFromMgPendings Counter32
  cmedxCmdTotalPendings Counter32

CmedxContextStatsEntry  
SEQUENCE    
  cmedxCntxNumActiveContexts Gauge32
  cmedxCntxPeakNumActiveContexts Gauge32
  cmedxCntxNumContextAllocated Counter32
  cmedxCntxNumContextFreed Counter32
  cmedxCntxShortestContextLife TimeTicks
  cmedxCntxAverageContextLife TimeTicks
  cmedxCntxLongestContextLife TimeTicks
  cmedxCntxNumCntxMoreThan2Terms Gauge32

CmedxPhysicalTermStatsEntry  
SEQUENCE    
  cmedxPhyTermStatsNumAdds Counter32
  cmedxPhyTermStatsNumFailures Counter32
  cmedxPhyTermStatsOosFromMgcs Counter32
  cmedxPhyTermStatsOosFromOams Counter32

CmedxEphemeralTermStatsEntry  
SEQUENCE    
  cmedxEphTermStatsType INTEGER
  cmedxEphTermStatsNumAdds Counter32
  cmedxEphTermStatsNumFailures Counter32

CmedxCommandProcStatsEntry  
SEQUENCE    
  cmedxCmdPhyTermAddRespTimeMin Gauge32
  cmedxCmdPhyTermAddRespTimeMax Gauge32
  cmedxCmdPhyTermAddRespTimeAvg Gauge32
  cmedxCmdPhyTermAddRespTimeCount Gauge32
  cmedxCmdPhyTermModRespTimeMin Gauge32
  cmedxCmdPhyTermModRespTimeMax Gauge32
  cmedxCmdPhyTermModRespTimeAvg Gauge32
  cmedxCmdPhyTermModRespTimeCount Gauge32
  cmedxCmdPhyTermSubRespTimeMin Gauge32
  cmedxCmdPhyTermSubRespTimeMax Gauge32
  cmedxCmdPhyTermSubRespTimeAvg Gauge32
  cmedxCmdPhyTermSubRespTimeCount Gauge32
  cmedxCmdEphTermAddRespTimeMin Gauge32
  cmedxCmdEphTermAddRespTimeMax Gauge32
  cmedxCmdEphTermAddRespTimeAvg Gauge32
  cmedxCmdEphTermAddRespTimeCount Gauge32
  cmedxCmdEphTermModRespTimeMin Gauge32
  cmedxCmdEphTermModRespTimeMax Gauge32
  cmedxCmdEphTermModRespTimeAvg Gauge32
  cmedxCmdEphTermModRespTimeCount Gauge32
  cmedxCmdEphTermSubRespTimeMin Gauge32
  cmedxCmdEphTermSubRespTimeMax Gauge32
  cmedxCmdEphTermSubRespTimeAvg Gauge32
  cmedxCmdEphTermSubRespTimeCount Gauge32
  cmedxCmdNumInProgCmds Gauge32
  cmedxCmdMaxInProgCmds Gauge32
  cmedxCmdSinceLastReset Unsigned32

CmedxOverloadStatsEntry  
SEQUENCE    
  cmedxOverloadEnterCounts Counter32SinceReset
  cmedxOverloadExitCounts Counter32SinceReset
  cmedxOverloadCurrentState INTEGER
  cmedxOverloadLastResetTime TimeStamp
  cmedxOverloadCountersClear TruthValue

CmedxOverloadResourceStatsEntry  
SEQUENCE    
  cmedxOverloadRsResourceIndex Unsigned32
  cmedxOverloadRsHighCounts Counter32SinceReset
  cmedxOverloadRsMedCounts Counter32SinceReset
  cmedxOverloadRsLowCounts Counter32SinceReset
  cmedxOverloadContributorCounts Counter32SinceReset
  cmedxOverloadRsLastResetTime TimeStamp
  cmedxOverloadRsCountersClear TruthValue

CmedxEphemeralTermStatsInfoEntry  
SEQUENCE    
  cmedxEphTermInfoStatsIndex Unsigned32
  cmedxEphTermInfoStatsIndexType INTEGER
  cmedxEphTermInfoNumTerm Counter32SinceReset
  cmedxEphTermInfoNumInUsed Gauge32
  cmedxEphTermInfoMaxNumInUsed Gauge32
  cmedxEphTermInfoMinDuration Gauge32
  cmedxEphTermInfoMaxDuration Gauge32
  cmedxEphTermInfoAvgDuration Gauge32
  cmedxEphTermInfoCounterClear TruthValue
  cmedxEphTermInfoSinceLastClear Unsigned32
  cmedxEphTermInfoSinceLastReset Unsigned32
  cmedxEphTermIndexInfo Unsigned32
  cmedxEphTermInfoNumFreed Unsigned32

Defined Values

ciscoMegacoExtMIB 1.3.6.1.4.1.9.10.104
The MIB module is an extension of CISCO-IETF-MEGACO-MIB. It defines the attributes of ITU H.248 protocol.
MODULE-IDENTITY    

ciscoMegacoExtMIBNotifications 1.3.6.1.4.1.9.10.104.0
OBJECT IDENTIFIER    

ciscoMegacoExtMIBObjects 1.3.6.1.4.1.9.10.104.1
OBJECT IDENTIFIER    

cmedxConfig 1.3.6.1.4.1.9.10.104.1.1
OBJECT IDENTIFIER    

cmedxStats 1.3.6.1.4.1.9.10.104.1.2
OBJECT IDENTIFIER    

cmedxGatewayConfigTable 1.3.6.1.4.1.9.10.104.1.1.1
The Cisco media gateway configuration extended table defines the parameters related to the configuration of the media gateway in H.248 protocol. Each entry represents an instance of an H.248 Gateway Link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxGatewayConfigEntry

cmedxGatewayConfigEntry 1.3.6.1.4.1.9.10.104.1.1.1.1
An entry containing additional H.248 protocol related configuration applicable to a media gateway. The following objects must be provided when the entry is created, and they can not be modified after the entry becomes active: cmedxGatewayMgcGroupIndex, cmedxGatewayIpAddressIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxGatewayConfigEntry  

cmedxGatewayMgcGroupIndex 1.3.6.1.4.1.9.10.104.1.1.1.1.1
This object specifies the MGC group parameters associated with MGC group index. Those parameters are for the communication between this media gateway and the MGCs in the group. The value of this object is the same as cMgcGrpIndex of cMgcGrpParamTable.
Status: current Access: read-create
OBJECT-TYPE    
  CMgcGroupIndex  

cmedxGatewayIpAddressIndex 1.3.6.1.4.1.9.10.104.1.1.1.1.2
This object specifies the media gateway IP address. It is the index of the entry in cMediaGwIpConfigTable which defines the media gateway address over control type PVC.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..64  

cmedxGatewayAssociationId 1.3.6.1.4.1.9.10.104.1.1.1.1.3
This object indicates the unique identification of the H.248 association assigned by the H.248 Stack.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..65535  

cmedxGatewayMaxContexts 1.3.6.1.4.1.9.10.104.1.1.1.1.4
Maximum number of contexts is allowed in this media gateway link.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..4294967295  

cmedxGatewayMaxTermsInContext 1.3.6.1.4.1.9.10.104.1.1.1.1.5
Maximum number of terminations per context in this media gateway link.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..100  

cmedxGatewayMgExecTime 1.3.6.1.4.1.9.10.104.1.1.1.1.6
This object specifies the interval within which the MGC expects a response to any transaction from the MG (exclusive of network delay specified by the object cmedxGatewayInitialRtt).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cmedxGatewayMgcExecTime 1.3.6.1.4.1.9.10.104.1.1.1.1.7
This object specifies the interval within which the MG should expects a response to any transaction from the MGC (exclusive of network delay specified by the object cmedxGatewayInitalRtt).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cmedxGatewayProvisionRespTime 1.3.6.1.4.1.9.10.104.1.1.1.1.8
This object specifies the time within which to expect a Pending Response if a transaction cannot be completed in the media gateway and in the MGCs of the media gateway link. The value of this object should be less than the value of cmedxGatewayMgExecTime and the value of cmedxGatewayMgcExecTime. This object is depricated due to the object name, default value and description are wrong. This object is replaced by 'cmedxGatewayMgProvisionRspTime'.
Status: deprecated Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cmedxGatewayNumConnRetries 1.3.6.1.4.1.9.10.104.1.1.1.1.9
The number of times the media gateway retries to connect to MGC before it sends out disconnect command.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

cmedxGatewayMaxWaitingDelay 1.3.6.1.4.1.9.10.104.1.1.1.1.10
When a media gateway is powered on, it should initiate a restart timer to a random value, uniformly distributed between 0 and the value specified in this object (the maximum waiting delay, MWD). After restart timer timeout, the media gateway can initiate the ServiceChange transaction. This is a way to prevent the MGC is swamped by many gateways powered up at the same time.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..600000  

cmedxGatewayRestartDelay 1.3.6.1.4.1.9.10.104.1.1.1.1.11
This object specifies The time delay before the media gateway accept any call from MGC after it sends the command 'ServiceChange' with a 'Restart'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..600  

cmedxGatewayRespRetentionTime 1.3.6.1.4.1.9.10.104.1.1.1.1.12
This object specifies the time till which the responses should be retained before they are sent if they receive a repetition of a transaction that is still being executed.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cmedxGatewayInitialRtt 1.3.6.1.4.1.9.10.104.1.1.1.1.13
Initial round-trip time for the H.248 transaction to be responded. It reflects the network delay time.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cmedxGatewayInactivityTime 1.3.6.1.4.1.9.10.104.1.1.1.1.14
This object specifies the the period of silence between messages from MGC. If the period of silence exceeds the value of this object, then a Notify command with inactive MGC event is generated from the media gateway. The value of 0 is to disable the inactivity detection on the media gateway.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cmedxGatewayHeaderAddrType 1.3.6.1.4.1.9.10.104.1.1.1.1.15
The address type in the H.248 message header.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

cmedxGatewayDownServiceDelay 1.3.6.1.4.1.9.10.104.1.1.1.1.16
This object specifies the grace period before the media gateway link to be taken out of service. The value of 0 means to take the media gateway link out of service forcefully without any delay. The value of -1 means not to take the media gateway link out of service until all currently active contexts have been cleared.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -1..65535  

cmedxGatewayActiveMgcAddress 1.3.6.1.4.1.9.10.104.1.1.1.1.17
The address of the currently active MGC in this media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cmedxGatewayActiveMgcDomain 1.3.6.1.4.1.9.10.104.1.1.1.1.18
The domain name of the currently active MGC in this media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cmedxGatewayActiveMgcPortNum 1.3.6.1.4.1.9.10.104.1.1.1.1.19
The transport layer port number of the currently active MGC in this media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  CiscoPort  

cmedxGatewayStateChangeReason 1.3.6.1.4.1.9.10.104.1.1.1.1.20
This object indicates the reason for the operational state change (cmedGatewayOperStatus) in the media gateway link. mgcDirected (1) - The state change is directed from MGC. mgDirected (2) - The state change is directed from MG. mgcNotReachable (3) - The transport address of MGC is not reachable. numRetriesExpired (4) - The number of retires for connecting MGC has exhausted (cmedxGatewayNumConnRetries).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER mgcDirected(1), mgDirected(2), mgcNotReachable(3), numRetriesExpired(4)  

cmedxGatewayStateChangeMethod 1.3.6.1.4.1.9.10.104.1.1.1.1.21
This object indicates the method for the operational state change (cmedGatewayOperStatus) in the media gateway link. other (1) - None of the methods listed below. graceful (2) - The state change to 'down(2)' is by the way of graceful out of service. forced (3) - The state change to 'down(2)' is by the way of forced out of service. handoff (4) - The state change is by the way that the MGC hands off to another MGC. failover (5) - The state change is by the way that MG reconnects to current MGC because of the failure of previous MGC. restart (6) - The state change is by the way that MG or MGC restarts. disconnect (7) - The state change is by the way that MG brings down the service because of the MG port has been modified, the number of retries has exhausted, or the inactivity timer has expired. cancelGraceful (8) - After issuing graceful out of service with a delay (cmedxGatewayDownServiceDelay>0), MG then sends an in-service command before the delay has been expired.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), graceful(2), forced(3), handoff(4), failover(5), restart(6), disconnect(7), cancelGraceful(8)  

cmedxGatewayAdminAction 1.3.6.1.4.1.9.10.104.1.1.1.1.22
This object specifies the action that users used to change the service state of the media gateway link. This object can be modified while the entry is active. up (1) - Bring the service state up. The value of cmedxGatewayDownServiceDelay will be ignored. downForceful (2) - Bring the service state down without any delay. All current active calls will be torn down forcefully. The value of cmedxGatewayDownServiceDelay must be 0. downGraceful (3) - Bring the service state down but wait until currently active calls are terminated by users. The value of cmedxGatewayDownServiceDelay must be greater than 0. cancelGraceful(4) - While waiting for all currently active calls to be terminated by users during the downGraceful action, this value can be used to cancel the previous action 'downGraceful(3)'. The value of cmedxGatewayDownServiceDelay will be ignored.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), downForceful(2), downGraceful(3), cancelGraceful(4)  

cmedxGatewayServiceState 1.3.6.1.4.1.9.10.104.1.1.1.1.23
This object indicates current operation status of the media gateway link. inService (1) - The media gateway link is in-service. pendingIs (2) - The media gateway link is in the process of establishing the service between MG and MGC. outOfService (3) - The service of the media gateway link is completely down due to the action of setting cmedxGAtewayAdminAction to 'downForceful(2)' or to 'downGraceful(3)'. pendingFoos (4) - The media gateway link is in the process of bringing down the service in response to the action of setting object cmedxGAtewayAdminAction to 'downForceful(2)'. pendingGoos (5) - The media gateway link is in the process of bringing down the service in response to the action of setting object cmedxGAtewayAdminAction to 'downGraceful(3)'. mgcDirectOos (6) - The media gateway link is out-of-service due to MGC disable the link. This state should occur very rarely, the way to recover from this state is to set cmedxGAtewayAdminAction to 'up(1)' or 'downForceful(2)'
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inService(1), pendingIs(2), outOfService(3), pendingFoos(4), pendingGoos(5), mgcDirectOos(6)  

cmedxGatewayDynamicTpktVersion 1.3.6.1.4.1.9.10.104.1.1.1.1.24
This object specifies the TPKT header version that is dynamically assigned based on the size of the packet presented to TCP layer. The TPKT header version is set to 3 when the size of packet is represented by 2 octets of packet length field for the message (TPDU) sizes less than or equal to 65531 octets. If this object is set to 'true': - The TPKT header version is set to 4 when the size of packet is represented by 4 octets of packet length field for the message (TPDU) sizes greater than 65531 octets. If this object is set to 'false': - An error in message is sent to MGC if the TPDU size exceeds 65531 octets indicating that response size exceeded maximum PDU size.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmedxGatewayMaxCommandMsgSize 1.3.6.1.4.1.9.10.104.1.1.1.1.25
This object specifies the maximum message size on this gateway link for a H248 transaction containing the media gateway initiated commands. For example, this object would limit the size of a H248 transaction containing the media gateway initiated ServiceChange command message. The value of the object cannot be modified if the entry is active.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..4096  

cmedxGatewayMaxReplyMsgSize 1.3.6.1.4.1.9.10.104.1.1.1.1.26
This object specifies the maximum message size on this gateway link for a H248 transaction containing the media gateway reply messages to MGC. For example, this object would limit the size of a H248 transaction containing the media gateway reply message to the MGC initiated AuditValue command. The value of the object cannot be modified if the entry is active.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..4096  

cmedxGatewaySctpAssocId 1.3.6.1.4.1.9.10.104.1.1.1.1.27
This object specifies the SCTP association ID associated with the H.248 association. This SCTP association ID is the index (cSctpAssocId) of the entry in cSctpAssocTable. If the SCTP ID value is 0, it indicates no SCTP association.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

cmedxGatewaySrvChgProfile 1.3.6.1.4.1.9.10.104.1.1.1.1.28
This object specifies the profile name used in the profile parameter of ServiceChange message to specify the attributes and behaviors of the media gateway.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..16)  

cmedxGatewaySrvChgProfileVer 1.3.6.1.4.1.9.10.104.1.1.1.1.29
This object specifies the version of the profile indicated in cmedxGatewaySrvChgProfile.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..99  

cmedxGatewayMsgTokenType 1.3.6.1.4.1.9.10.104.1.1.1.1.30
This object specifies the H248 message is in short formatted PDU or long formatted PDU.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER shortFormat(1), longFormat(2)  

cmedxGatewayMgProvisionRspTime 1.3.6.1.4.1.9.10.104.1.1.1.1.31
This object specifies the time within which to expect a Pending Response if a transaction cannot be completed in the media gateway and in the MGCs of the media gateway link. The value of this object should be greater than the value of cmedxGatewayMgExecTime.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cmedxGatewayMgcProvisionRspTime 1.3.6.1.4.1.9.10.104.1.1.1.1.32
This object specifies the time within which to expect a Pending Response from the MGC if a transaction cannot be completed. The value of this object should be greater than the value of cmedxGatewayMgcExecTime.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cmedxGatewayMgOrigPendLimit 1.3.6.1.4.1.9.10.104.1.1.1.1.33
This object specifies the number of TransactionPendings that MG will send. Once this limit is exceeded, MG will send a TransactionReply with Error 506.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cmedxGatewayMgcOrigPendLimit 1.3.6.1.4.1.9.10.104.1.1.1.1.34
This object specifies the number of TransactionPendings that MG expects to receive. Once this limit is exceeded, MG will assume a TransactionReply with Error 506.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

cmedxGatewayDomainName 1.3.6.1.4.1.9.10.104.1.1.1.1.35
This object specifies the unique domain name to be used for each gateway link. This object is relevant only if cmedxGatewayHeaderAddrType is set to 'dns'. The agent won't allow any attempt to set this value for other address types. This domain name is expected to be resolved to a valid IP address through the use of a DNS located in the network. The default value of this object is NULL string.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

cmedxGatewayCmbDnAndPortInMID 1.3.6.1.4.1.9.10.104.1.1.1.1.36
This object specifies whether the MID should be a combination of the transport port number and the domain name represented by cmedGatewayPort and cmedxGatewayDomainName respectively, when cmedxGatewayHeaderAddrType is 'dns' . A value of 'true' indicates that the MID will be a combination of the domain name and the transport port number. A value of 'false' indicates that MID will contain only the domain name and not the port number. The agent won't allow any attempt to set this object for other address types.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmedxTerminationTypeTable 1.3.6.1.4.1.9.10.104.1.1.2
This table defines the attributes of a termination type for a group of ephemeral terminations.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxTerminationTypeEntry

cmedxTerminationTypeEntry 1.3.6.1.4.1.9.10.104.1.1.2.1
Each entry represents one termination type for a group of ephemeral terminations in H.248. When creating an entry, the object cmedxTermType have to be provided.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxTerminationTypeEntry  

cmedxTermTypeId 1.3.6.1.4.1.9.10.104.1.1.2.1.1
An unique identification number that is assigned to the termination type by the manager
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..65535  

cmedxTermType 1.3.6.1.4.1.9.10.104.1.1.2.1.2
This object specifies the type of a group of ephemeral terminations. unknown (1) - none of the types listed below. scn (2) - SCN/DS terminations pdnRtp (3) - PDN terminations of RTP type. pdnAtmAal1 (4) - PDN terminations of ATM type with AAL1 adaptation layer. pdnAtmAal2 (5) - PDN terminations of ATM type with AAL2 adaptation layer. If the value of this object is set to scn(2) or pdnRtp(3), the value of cmedxProfileAtmAalType for the profile of this termination type should be other(1). If the value of this object is set to pdnAtmAal1(4), the value of cmedxProfileAtmAalType for the profile of this termination type should be aal1(2), aal1Sdt(3), or aal1Udt(4). If the value of this object is set to pdnAtmAal2(5), the value of cmedxProfileAtmAalType for the profile of this termination type should be aal2(5).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER unknown(1), scn(2), pdnRtp(3), pdnAtmAal1(4), pdnAtmAal2(5)  

cmedxTermTypeProfileId 1.3.6.1.4.1.9.10.104.1.1.2.1.3
The property profile identifier with which the terminations within this termination type will be associated.
Status: current Access: read-create
OBJECT-TYPE    
  CCallControlProfileIndexOrZero  

cmedxTermTypePkgIds 1.3.6.1.4.1.9.10.104.1.1.2.1.4
The H.248 packages applied to this termination type.
Status: current Access: read-create
OBJECT-TYPE    
  CH248Packages  

cmedxTermTypeRowStatus 1.3.6.1.4.1.9.10.104.1.1.2.1.5
This object is used to create new rows, modify existing rows and to delete existing rows.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmedxProfileTable 1.3.6.1.4.1.9.10.104.1.1.3
This table contains a list of the configurable properties in the H.248 profile supported in a media gateway. A property profile can be applied to a termination, a group of termination, or a termination type.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxProfileEntry

cmedxProfileEntry 1.3.6.1.4.1.9.10.104.1.1.3.1
Each entry represents all possible configurable properties supported by Cisco media gateway in an H.248 profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxProfileEntry  

cmedxProfileIndex 1.3.6.1.4.1.9.10.104.1.1.3.1.1
This object uniquely identifies the H.248 profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  CCallControlProfileIndex  

cmedxProfilePlayCpToneInterDur 1.3.6.1.4.1.9.10.104.1.1.3.1.2
This object specifies the duration for playing a list of call progressing tones between two call progressing signals. The value of 0 indicates there is no wait between two call progressing signals.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cmedxProfileDtmfDigitOnDur 1.3.6.1.4.1.9.10.104.1.1.3.1.3
This object specifies the duration of the active DTMF digit during DTMF playout from the gateway. A complete DTMF digit is characterized by DTMF on with duration specified by this object followed by a pause (signal off) duration specified by the object cmedxProfileDtmfPauseDuration.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 40..4294967295  

cmedxProfileDtmfPauseDur 1.3.6.1.4.1.9.10.104.1.1.3.1.4
This object specifies the duration of the pause after an active DTMF digit during DTMF playout from the gateway. For playout of multiple DTMF digits, the sum of the digit-on and pause (signaling velocity) should not be shorter than the time specified in Q.23, Q.24 and EIA/TIA-464. For example, 93ms/digit for AT&T, 120ms/digit for NTT, 100ms/digit for Danish Administration.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 40..4294967295  

cmedxProfileCot1Frequency 1.3.6.1.4.1.9.10.104.1.1.3.1.5
This object specifies the tone frequency to be transmit between gateways in the continuity test.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..4000  

cmedxProfileCot2Frequency 1.3.6.1.4.1.9.10.104.1.1.3.1.6
This object specifies the tone frequency to be received between gateways in the continuity test.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..4000  

cmedxProfileInitiateCotDur 1.3.6.1.4.1.9.10.104.1.1.3.1.7
This object specifies the duration for the continuity test tone to be played when the gateway initiates a COT. The value of 0 indicates that the tone will be played infinitely unless interrupted.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cmedxProfileRespCotMethod 1.3.6.1.4.1.9.10.104.1.1.3.1.8
This object specifies the method for responding to COT (Continuity Test Tone) when the gateway detects a the continuity test signal. loopback (1) - The gateway loops back the received continuity test signal. transponder (2) - The gateway responds with another continuity test signal upon detecting a continuity test signal. When this object is set to loopback(1), the originating gateway transmits the frequency specified in the value of cmedxProfileCot1Frequency, the terminating gateway loops back whatever it receives. When this object is set to transponder(2), the originating gateway transmit the frequency specified in the value of cmedxProfileCot1Frequency, and the terminating gateway responds the frequency specified in the value of cmedxProfileCot2Frequency.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER loopback(1), transponder(2)  

cmedxProfileDetectLongCpToneDur 1.3.6.1.4.1.9.10.104.1.1.3.1.9
This object specifies the duration for detecting a long call progressing tone.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cmedxProfileDetectLongDigitDur 1.3.6.1.4.1.9.10.104.1.1.3.1.10
This object specifies the duration for detecting a long digit tone signal.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cmedxProfileEchoCancelEnabled 1.3.6.1.4.1.9.10.104.1.1.3.1.11
This object specifies whether or not the Echo Cancellation is enabled or not.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmedxProfileEchoCancelTail 1.3.6.1.4.1.9.10.104.1.1.3.1.12
This object specifies the Echo Canceler coverage. This object is valid if the cmedxProfileEchoCancelEnabled object is 'true'. echoCanceller8ms - 8 ms echo canceler coverage. echoCanceller16ms - 16 ms echo canceler coverage. echoCanceller24ms - 24 ms echo canceler coverage. echoCanceller32ms - 32 ms echo canceler coverage. echoCanceller64ms - 64 ms echo canceler coverage. echoCanceller128ms- 128 ms echo canceler coverage.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER echoCanceller8ms(1), echoCanceller16ms(2), echoCanceller24ms(3), echoCanceller32ms(4), echoCanceller64ms(5), echoCanceller128ms(6)  

cmedxProfileInGainControl 1.3.6.1.4.1.9.10.104.1.1.3.1.13
This object contains the amount of gain inserted at the receiver side of the interface. The input gain settings only define a gain/loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -6..14  

cmedxProfileOutAttnControl 1.3.6.1.4.1.9.10.104.1.1.3.1.14
This object contains the amount of attenuation inserted at the transmit side of the interface. The output attenuation settings only define a loss relative to the 0 dB setting. The absolute loss at the 0 dB setting could be implementation dependent based on the desired network loss plan.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..14  

cmedxProfileVoIpVadEnabled 1.3.6.1.4.1.9.10.104.1.1.3.1.15
This object specifies VAD (Voice Activity Detection) is enabled for the compression DSPs of this interface when the application is VoIP.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmedxProfileVoIpVadTimer 1.3.6.1.4.1.9.10.104.1.1.3.1.16
This object specifies the hangover time for VAD in the VoIP application. Once the voice inactivity is detected, the media gateway waits for the duration of this value before activating silence suppression. This object is not applicable if cmedxProfileVoIpVadEnabled is set to 'false'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cmedxProfileVoAal2VadTimer 1.3.6.1.4.1.9.10.104.1.1.3.1.17
This object specifies the hangover time for VAD in the VoATM over AAL2 application. Once the voice inactivity is detected, the media gateway waits for the duration of this value before activating silence suppression. This object is not applicable if cvapAal2ProfVad is set to 'vadOff'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cmedxProfileAtmBearerType 1.3.6.1.4.1.9.10.104.1.1.3.1.18
This object specifies ATM bearer type. bearerSvc (1) - the ATM bearer type is SVC (Switched Virtual Circuit). bearerPvc (1) - the ATM bearer type is PVC (Permanent Virtual Circuit).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER bearerSvc(1), bearerPvc(2)  

cmedxProfileAtmAalPartialFill 1.3.6.1.4.1.9.10.104.1.1.3.1.19
This object specifies the fill level of cells in case of AAL adaptation . The value of this object will be used if the MGC does not specify partial fill in the commands. ATM cell size is 53 bytes, 5 bytes for header, 48 bytes for data. If the data are not enough to fill 48 bytes of one ATM cell, the system can fill in the value of this object to the padding bytes.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..48  

cmedxProfileAtmAalType 1.3.6.1.4.1.9.10.104.1.1.3.1.20
This object specifies the adaptation layer of ATM. other (1) - None of the types listed below. aal1 (2) - ATM AAL1 adaptation layer aal1Sdt (3) - ATM AAL1 with SDT (Structured Data Transfer) aal1Udt (4) - ATM AAL1 with UDT (Unstructured Data Transfer). aal2 (5) - ATM AAL2 adaptation layer.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER other(1), aal1(2), aal1Sdt(3), aal1Udt(4), aal2(5)  

cmedxProfileSuppressBearerDigit 1.3.6.1.4.1.9.10.104.1.1.3.1.21
This object controls if the digits should be suppressed from voice media stream. When MGC has requested digits, if this object is set to 'true', the digits will be reported to MGC only, the digits will not be sent as regular voice or peer-to-peer packets in the bearer. When MGC has requested digits, if this object is set to 'false', the digits will be reported to MGC as well as be sent in the bearer according to the value of cvapCodecConfigDtmfRelay in cvapCodecConfigTable. When MGC has not requested digits, this object will be ignored. The digits will be sent in the bearer according to the value of cvapCodecConfigDtmfRelay in cvapCodecConfigTable.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cmedxProfileRowStatus 1.3.6.1.4.1.9.10.104.1.1.3.1.22
When an entry is created, at least one of the objects in the entry has to be provided and the default value will be assigned to the rest of the objects.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cmedxProfileOriginatingCotTx 1.3.6.1.4.1.9.10.104.1.1.3.1.23
This object specifies the COT tone to be transmitted from originating gateway in the continuity test.
Status: current Access: read-create
OBJECT-TYPE    
  CMedxCotTones  

cmedxProfileOriginatingCotRx 1.3.6.1.4.1.9.10.104.1.1.3.1.24
This object specifies the COT tone to be received in originating gateway in the continuity test.
Status: current Access: read-create
OBJECT-TYPE    
  CMedxCotTones  

cmedxProfileTerminatingCotTx 1.3.6.1.4.1.9.10.104.1.1.3.1.25
This object specifies the COT tone to be transmitted from terminating gateway in the continuity test.
Status: current Access: read-create
OBJECT-TYPE    
  CMedxCotTones  

cmedxProfileTerminatingCotRx 1.3.6.1.4.1.9.10.104.1.1.3.1.26
This object specifies the COT tone to be received in terminating gateway in the continuity test.
Status: current Access: read-create
OBJECT-TYPE    
  CMedxCotTones  

cmedxProfileComfortNoiseGenerate 1.3.6.1.4.1.9.10.104.1.1.3.1.27
This object specifies the type of comfort noise generation: (1) none: No comfort noise generation applied (2) simple: Cisco Proprietary comfort noise generation (3) g711A2: ITU G.711 Appendix II compliant
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), simple(2), g711A2(3)  

cmedxCallReduceControlTable 1.3.6.1.4.1.9.10.104.1.1.4
The MIB objects in this table are used to control the rate at which call attempts are made by Media gateway controller on this Media Gateway.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxCallReduceControlEntry

cmedxCallReduceControlEntry 1.3.6.1.4.1.9.10.104.1.1.4.1
An entry in this table contains the control parameters that indicate the frequency and number of notifications sent to MGC in the event congestion is detected on MG.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxCallReduceControlEntry  

cmedxCallCongEnabled 1.3.6.1.4.1.9.10.104.1.1.4.1.1
This object controls if the H.248 congestion package (H.248.10) and its associated features should be enabled for the media gateway. If this object is set to 'false', then the following MIB objects and MIB table will be ignored: cmedxCallRenotifInterval cmedxCRRNumOfLevel cmedxCurrentCRR cmedxCrrNotifyState cmedxCrrNotifyEnabled cmedxCallReduceLevelTable.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmedxCallRenotifInterval 1.3.6.1.4.1.9.10.104.1.1.4.1.2
This object specifies the interval of the congestion renotification from the media gateway to the MGC. In the event of congestion on the Media Gateway, gateway generates an event towards MGC. Using this message, MG requests percentage reduction in the rate of calls that MGC is attempting towards MG. After sending this indication, MG starts a timer based on 'cmedxCallRenotifInterval'. At this timer expires, MG will re-send the message to MGC indicating that it is still in congested state. If MGC does not receive another notification, MGC will resume to the original call rate. If MGC requires re-notifications, it is user's responsibility to set the value of this MIB object on MG appropriately. The value of this object should be set such that it factors into the network delay and re-notification timer (similar to this MIB object) configured on MGC. The zero means MGC does not require re-notifications, MGC will keep CallReduceRate until receive another notification from the Media Gateway.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

cmedxCRRNumOfLevel 1.3.6.1.4.1.9.10.104.1.1.4.1.3
This objects specifies the number of level corresponding to which a different call reduction rate notification is generated towards MGC. Each level has a different call reduction rate, the CRR information is stored on cmedxCallReduceLevelTabl. And The table size equals to the value of 'cmedxCRRNumOfLevel'.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..16  

cmedxCurrentCRR 1.3.6.1.4.1.9.10.104.1.1.4.1.4
This object indicates the current percentage reduction in the rate of calls that MGC is attempting towards MG.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100  

cmedxCrrNotifyState 1.3.6.1.4.1.9.10.104.1.1.4.1.5
This object indicates the current gateway congestion notification state. The value of 'true' means the gateway will notify MGC when the gateway is congested. The value of 'false' means the gateway won't notify MGC when the gateway is congested. This object is 'true' when cmedxCallCongEnabled is set to 'true' and at least one of MGCs enabled the CRR notification (cmedxCrrNotifyEnabled is not 0).
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmedxCrrNotifyEnabled 1.3.6.1.4.1.9.10.104.1.1.4.1.6
This object indicates the bit map of the H248 association index (cmedGatewayLinkId) in which the gateway congestion notification is enabled. The MSB (most significant bit) is the association index 1. A 1-bit indicates the gateway congestion notification is enabled in this H248 association. A 0-bit indicates it is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

cmedxCurrentCallState 1.3.6.1.4.1.9.10.104.1.1.4.1.7
This object indicates the state of the gateway in accepting the incoming new call. acceptCall - the incoming new call will be processed. dropCall - the incoming new call will be droped due to the resources congested.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER acceptCall(1), dropCall(2)  

cmedxCallReduceLevelTable 1.3.6.1.4.1.9.10.104.1.1.5
The table presents mapping between a level and corresponding call reduction rate.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxCallReduceLevelEntry

cmedxCallReduceLevelEntry 1.3.6.1.4.1.9.10.104.1.1.5.1
The number of entry on this table is determined by the MIB object 'cmedxCRRNumOfLevel'.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxCallReduceLevelEntry  

cmedxCallReduceLevelNum 1.3.6.1.4.1.9.10.104.1.1.5.1.1
The index starts from 1, and the maximum index equals to 'cmedxCRRNumOfLevel'.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..16  

cmedxCallReduceRate 1.3.6.1.4.1.9.10.104.1.1.5.1.2
This object indicates call reduction rate (CRR) for a given call reduce rate level. The default value of this object is based on the formula: level 1: 100 other level: 100 - ((80/(nol - 1)) * (level - 1)) Here: nol : number of level(cmedxCRRNumOfLevel) level: specific level (cmedxCallReduceLevelNum) User can configure this object, the rule is: level x > level x+1
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..100  

cmedxOverloadControlTable 1.3.6.1.4.1.9.10.104.1.1.7
This table is used to configure the media gateway overload control parameters specified in H.248.11 package.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxOverloadControlEntry

cmedxOverloadControlEntry 1.3.6.1.4.1.9.10.104.1.1.7.1
An entry in this table contains the overload control parameters of the media gateway.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxOverloadControlEntry  

cmedxOverloadControlEnabled 1.3.6.1.4.1.9.10.104.1.1.7.1.1
This object controls if the H.248 overload package (H.248.11) and its associated features should be enabled for the media gateway. If this object is set to 'false', then the following MIB objects and MIB table will be ignored: cmedxOverloadNotifyState cmedxOverloadNotifyEnabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmedxOverloadNotifyState 1.3.6.1.4.1.9.10.104.1.1.7.1.2
This object indicates the current gateway overload notification state. The value of 'true' means the gateway will notify MGC when the gateway is overloaded. The value of 'false' means the gateway won't notify MGC when the gateway is overloaded. This object is 'true' when cmedxOverloadControlEnabled is set to 'true' and at least one of MGCs enabled gateway overload notification (cmedxOverloadNotifyEnabled is not 0).
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

cmedxOverloadNotifyEnabled 1.3.6.1.4.1.9.10.104.1.1.7.1.3
This object indicates the bit map of the H248 association index (cmedGatewayLinkId) in which the gateway overload notification is enabled. The MSB (most significant bit) is the association index 1. A 1-bit indicates the gateway overload notification is enabled in this H248 association. A 0-bit indicates it is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

cmedxCodecNegotiationTable 1.3.6.1.4.1.9.10.104.1.1.6
This table contains configuration information for different type of CODEC negotiation of calls which include voice call over adaptation layer AAL1 and AAL5. If the value lclLcoRcd(5), lclRcdLco(6) of cvapCodecNegotiationOption is used as CODEC negotiation option, the CODEC list configuration information in this table will be used for CODEC negotiation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxCodecNegotiationEntry

cmedxCodecNegotiationEntry 1.3.6.1.4.1.9.10.104.1.1.6.1
An entry represents a CODEC rate supported for VoIP or VoATM with AAL1 or AAL5 application in the media gateway. A list of entries for all CODEC types supported in the media gateway are created by the agent when a cmedxProfileEntry is created.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxCodecNegotiationEntry  

cmedxCodecNegotiationCodec 1.3.6.1.4.1.9.10.104.1.1.6.1.1
This object specifies the CODEC to be used in this profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  CvcSpeechCoderRate  

cmedxCodecNegotiationPreference 1.3.6.1.4.1.9.10.104.1.1.6.1.2
This object specified the preference configured by the user for each CODEC. Lower the number, higher the preference of the CODEC. If this object is set to 0, the corresponding CODEC will not be used in coded negotiation procedure. Initially, if the value of cmedxCodecNegotiationCodec is g711u, this object is set to 1, else this object is set to 0. For CODECs having the same preference, the entry with the lower index has higher precedence.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..255  

cmedxGatewayStatsTable 1.3.6.1.4.1.9.10.104.1.2.1
This table is extended from cmedGatewayStatsTable which contains additional control protocol related statistics of the media gateway link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxGatewayStatsEntry

cmedxGatewayStatsEntry 1.3.6.1.4.1.9.10.104.1.2.1.1
Entry holding statistics about a group of media Gateway/signaling link pair
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxGatewayStatsEntry  

cmedxGatewayLastEvent 1.3.6.1.4.1.9.10.104.1.2.1.1.1
The event code of the last event occurred on the link.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..1000  

cmedxCommandStatsTable 1.3.6.1.4.1.9.10.104.1.2.2
This table provides the H.248 Command related statistics for the media gateway link. The H.248 protocol provides commands for manipulating the logical entities of the protocol connection model, Contexts and Terminations. For example, Commands exist to add Terminations to a Context, modify Terminations, subtract Terminations from a Context, and audit properties of Contexts or Terminations. Most commands are for the specific use of the Media Gateway Controller (MGC) as command initiator in controlling Media Gateways (MG) as command responders. The exceptions are the Notify and ServiceChange commands: Notify is sent from Media Gateway to Media Gateway Controller, and ServiceChange may be sent by either entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxCommandStatsEntry

cmedxCommandStatsEntry 1.3.6.1.4.1.9.10.104.1.2.2.1
The system creates one entry for each media gateway link when it is created.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxCommandStatsEntry  

cmedxCmdNumAddFails 1.3.6.1.4.1.9.10.104.1.2.2.1.1
Total number of cumulative ADD commands failed in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumAddSucceeds 1.3.6.1.4.1.9.10.104.1.2.2.1.2
Total number of cumulative ADD command succeeded in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumSubtractFails 1.3.6.1.4.1.9.10.104.1.2.2.1.3
Total number of cumulative SUBTRACT commands failed in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumSubtractSucceeds 1.3.6.1.4.1.9.10.104.1.2.2.1.4
Total number of cumulative SUBTRACT commands succeeded in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumMoveFails 1.3.6.1.4.1.9.10.104.1.2.2.1.5
Total number of cumulative MOVE commands failed in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumMoveSucceeds 1.3.6.1.4.1.9.10.104.1.2.2.1.6
Total number of cumulative MOVE commands succeeded in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumModifyFails 1.3.6.1.4.1.9.10.104.1.2.2.1.7
Total number of cumulative MODIFY commands failed in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumModifySucceeds 1.3.6.1.4.1.9.10.104.1.2.2.1.8
Total number of cumulative MODIFY commands succeeded in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumAuditValFails 1.3.6.1.4.1.9.10.104.1.2.2.1.9
Total number of cumulative AUDIT VALUE commands failed in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumAuditValSucceeds 1.3.6.1.4.1.9.10.104.1.2.2.1.10
Total number of cumulative AUDIT VALUE commands succeeded in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumAuditCapFails 1.3.6.1.4.1.9.10.104.1.2.2.1.11
Total number of cumulative AUDIT CAPABILITY commands failed in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumAuditCapSucceeds 1.3.6.1.4.1.9.10.104.1.2.2.1.12
Total number of cumulative AUDIT CAPABILITY commands succeeded in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumNotifyFails 1.3.6.1.4.1.9.10.104.1.2.2.1.13
Total number of cumulative NOTIFY commands failed to respond from MGC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumNotifySucceeds 1.3.6.1.4.1.9.10.104.1.2.2.1.14
Total number of cumulative NOTIFY commands successfully responded from the MGC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumSrvChgFromMgcFails 1.3.6.1.4.1.9.10.104.1.2.2.1.15
Total number of cumulative ServiceChange commands from MGC to MG failed in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumSrvChgFromMgcSucceeds 1.3.6.1.4.1.9.10.104.1.2.2.1.16
Total number of cumulative ServiceChange commands from MGC to MG succeeded in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumSrvChgFromMgFails 1.3.6.1.4.1.9.10.104.1.2.2.1.17
Total number of cumulative ServiceChange commands from MG to MGC failed in MGC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumSrvChgFromMgSucceeds 1.3.6.1.4.1.9.10.104.1.2.2.1.18
Total number of cumulative ServiceChange commands from MG to MGC succeeded in MGC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdTotalFails 1.3.6.1.4.1.9.10.104.1.2.2.1.19
Total number of commands failed in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdTotalSucceeds 1.3.6.1.4.1.9.10.104.1.2.2.1.20
Total number of commands succeeded in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdTotal 1.3.6.1.4.1.9.10.104.1.2.2.1.21
Total number of failed and successful commands in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumAddPendings 1.3.6.1.4.1.9.10.104.1.2.2.1.22
Total number of cumulative ADD commands remain pending in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumSubtractPendings 1.3.6.1.4.1.9.10.104.1.2.2.1.23
Total number of cumulative SUBTRACT commands remain pending in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumMovePendings 1.3.6.1.4.1.9.10.104.1.2.2.1.24
Total number of cumulative MOVE commands remain pending in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumModifyPendings 1.3.6.1.4.1.9.10.104.1.2.2.1.25
Total number of cumulative MODIFY commands remain pending in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumAuditValPendings 1.3.6.1.4.1.9.10.104.1.2.2.1.26
Total number of cumulative AUDIT VALUE commands remain pending in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumAuditCapPendings 1.3.6.1.4.1.9.10.104.1.2.2.1.27
Total number of cumulative AUDIT CAPABILITY commands remain pending in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumNotifyPendings 1.3.6.1.4.1.9.10.104.1.2.2.1.28
Total number of cumulative NOTIFY commands remain pending in response from MGC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumSrvChgFromMgcPendings 1.3.6.1.4.1.9.10.104.1.2.2.1.29
Total number of cumulative ServiceChange commands from MGC to MG remain pending in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdNumSrvChgFromMgPendings 1.3.6.1.4.1.9.10.104.1.2.2.1.30
Total number of cumulative ServiceChange commands from MG to MGC remain pending in MGC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCmdTotalPendings 1.3.6.1.4.1.9.10.104.1.2.2.1.31
Total number of commands remain pending in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxContextStatsTable 1.3.6.1.4.1.9.10.104.1.2.3
This table provides the H.248 Context related statistics for the media gateway link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxContextStatsEntry

cmedxContextStatsEntry 1.3.6.1.4.1.9.10.104.1.2.3.1
The system creates one entry for each media gateway link when it is created.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxContextStatsEntry  

cmedxCntxNumActiveContexts 1.3.6.1.4.1.9.10.104.1.2.3.1.1
The current number of active contexts in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCntxPeakNumActiveContexts 1.3.6.1.4.1.9.10.104.1.2.3.1.2
Peak number of active contexts in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCntxNumContextAllocated 1.3.6.1.4.1.9.10.104.1.2.3.1.3
Total number of contexts has been allocated in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCntxNumContextFreed 1.3.6.1.4.1.9.10.104.1.2.3.1.4
Total number of contexts has been freed in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCntxShortestContextLife 1.3.6.1.4.1.9.10.104.1.2.3.1.5
The shortest life span for the contexts in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

cmedxCntxAverageContextLife 1.3.6.1.4.1.9.10.104.1.2.3.1.6
The average life span for the contexts in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

cmedxCntxLongestContextLife 1.3.6.1.4.1.9.10.104.1.2.3.1.7
The longest life span for the contexts in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

cmedxCntxNumCntxMoreThan2Terms 1.3.6.1.4.1.9.10.104.1.2.3.1.8
The number of contexts having more than 2 terminations in the media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxPhysicalTermStatsTable 1.3.6.1.4.1.9.10.104.1.2.4
This table contains statistics related to physical terminations in a media gateway.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxPhysicalTermStatsEntry

cmedxPhysicalTermStatsEntry 1.3.6.1.4.1.9.10.104.1.2.4.1
Each entry contains the statistics for a physical termination in the media gateway.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxPhysicalTermStatsEntry  

cmedxPhyTermStatsNumAdds 1.3.6.1.4.1.9.10.104.1.2.4.1.1
Number of total ADD commands on this physical termination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxPhyTermStatsNumFailures 1.3.6.1.4.1.9.10.104.1.2.4.1.2
Number of total command failures on this physical termination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxPhyTermStatsOosFromMgcs 1.3.6.1.4.1.9.10.104.1.2.4.1.3
Number of total out of service initiated from MGC on this physical termination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxPhyTermStatsOosFromOams 1.3.6.1.4.1.9.10.104.1.2.4.1.4
Number of total out of service initiated from OAM (Operation Administration Management, either MG or NMS) on this physical termination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxEphemeralTermStatsTable 1.3.6.1.4.1.9.10.104.1.2.5
This table contains statistics related to ephemeral terminations.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxEphemeralTermStatsEntry

cmedxEphemeralTermStatsEntry 1.3.6.1.4.1.9.10.104.1.2.5.1
Each entry contains the statistics of all ephemeral terminations for the termination type.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxEphemeralTermStatsEntry  

cmedxEphTermStatsType 1.3.6.1.4.1.9.10.104.1.2.5.1.1
This object specifies the statistics of the termination type to be retrieved. all (1) - Statistics for all ephemeral termination types. scn (2) - Statistics for SCN/DS terminations pdnRtp (3) - Statistics for PDN terminations of RTP type. pdnAtmAal1 (4) - Statistics for PDN terminations of ATM type with AAL1 adaptation layer. pdnAtmAal2 (5) - Statistics for PDN terminations of ATM type with AAL2 adaptation layer.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER all(1), scn(2), pdnRtp(3), pdnAtmAal1(4), pdnAtmAal2(5)  

cmedxEphTermStatsNumAdds 1.3.6.1.4.1.9.10.104.1.2.5.1.2
Number of total ADD commands has been initiated on this termination type.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxEphTermStatsNumFailures 1.3.6.1.4.1.9.10.104.1.2.5.1.3
Number of total command failures on this termination type.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cmedxCommandProcStatsTable 1.3.6.1.4.1.9.10.104.1.2.6
This table provides the statistics related to H.248 command processing on a media gateway link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxCommandProcStatsEntry

cmedxCommandProcStatsEntry 1.3.6.1.4.1.9.10.104.1.2.6.1
The information in each entry is for a media gateway link.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxCommandProcStatsEntry  

cmedxCmdPhyTermAddRespTimeMin 1.3.6.1.4.1.9.10.104.1.2.6.1.1
The minimum add response time (ms) for physical terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermAddRespTimeMax 1.3.6.1.4.1.9.10.104.1.2.6.1.2
The maximum add response time (ms) for physical terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermAddRespTimeAvg 1.3.6.1.4.1.9.10.104.1.2.6.1.3
The average add response time (ms) for physical terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermAddRespTimeCount 1.3.6.1.4.1.9.10.104.1.2.6.1.4
The number of add responses for physical terminations which have been sent during the statistics interval on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermModRespTimeMin 1.3.6.1.4.1.9.10.104.1.2.6.1.5
The minimum modify response time (ms) for physical terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermModRespTimeMax 1.3.6.1.4.1.9.10.104.1.2.6.1.6
The maximum modify response time (ms) for physical terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermModRespTimeAvg 1.3.6.1.4.1.9.10.104.1.2.6.1.7
The average modify response time (ms) for physical terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermModRespTimeCount 1.3.6.1.4.1.9.10.104.1.2.6.1.8
The number of modify responses for physical terminations which have been sent during the statistics interval on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermSubRespTimeMin 1.3.6.1.4.1.9.10.104.1.2.6.1.9
The minimum subtract response time (ms) for physical terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermSubRespTimeMax 1.3.6.1.4.1.9.10.104.1.2.6.1.10
The maximum subtract response time (ms) for physical terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermSubRespTimeAvg 1.3.6.1.4.1.9.10.104.1.2.6.1.11
The average subtract response time (ms) for physical terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdPhyTermSubRespTimeCount 1.3.6.1.4.1.9.10.104.1.2.6.1.12
The number of subtract responses for physical terminations which have been sent during the statistics interval on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermAddRespTimeMin 1.3.6.1.4.1.9.10.104.1.2.6.1.13
The minimum add response time (ms) for ephemeral terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermAddRespTimeMax 1.3.6.1.4.1.9.10.104.1.2.6.1.14
The maximum add response time (ms) for ephemeral terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermAddRespTimeAvg 1.3.6.1.4.1.9.10.104.1.2.6.1.15
The average add response time (ms) for ephemeral terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermAddRespTimeCount 1.3.6.1.4.1.9.10.104.1.2.6.1.16
The number of add responses for ephemeral terminations which have been sent during the statistics interval on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermModRespTimeMin 1.3.6.1.4.1.9.10.104.1.2.6.1.17
The minimum modify response time (ms) for ephemeral terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermModRespTimeMax 1.3.6.1.4.1.9.10.104.1.2.6.1.18
The maximum modify response time (ms) for ephemeral terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermModRespTimeAvg 1.3.6.1.4.1.9.10.104.1.2.6.1.19
The average modify response time (ms) for ephemeral terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermModRespTimeCount 1.3.6.1.4.1.9.10.104.1.2.6.1.20
The number of modify responses for ephemeral terminations which have been sent during the statistics interval on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermSubRespTimeMin 1.3.6.1.4.1.9.10.104.1.2.6.1.21
The minimum subtract response time (ms) for ephemeral terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermSubRespTimeMax 1.3.6.1.4.1.9.10.104.1.2.6.1.22
The maximum subtract response time (ms) for ephemeral terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermSubRespTimeAvg 1.3.6.1.4.1.9.10.104.1.2.6.1.23
The average subtract response time (ms) for ephemeral terminations on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdEphTermSubRespTimeCount 1.3.6.1.4.1.9.10.104.1.2.6.1.24
The number of subtract responses for ephemeral terminations which have been sent during the statistics interval on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdNumInProgCmds 1.3.6.1.4.1.9.10.104.1.2.6.1.25
The number of in-progress commands on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdMaxInProgCmds 1.3.6.1.4.1.9.10.104.1.2.6.1.26
The maximum number of in-progress commands on a media gateway link.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxCmdSinceLastReset 1.3.6.1.4.1.9.10.104.1.2.6.1.27
The elapsed time (in seconds) from the last periodic reset. All (non-accumulator) statistic objects were zeroed on the last reset.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cmedxOverloadStatsTable 1.3.6.1.4.1.9.10.104.1.2.7
This table contains statistics related to gateway overload control (H.248.11).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxOverloadStatsEntry

cmedxOverloadStatsEntry 1.3.6.1.4.1.9.10.104.1.2.7.1
Each entry contains the statistics of gateway overload control.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxOverloadStatsEntry  

cmedxOverloadEnterCounts 1.3.6.1.4.1.9.10.104.1.2.7.1.1
The number of times that the gateway enters the overload condition because of any of CAC monitoring resources has exceeded the medium threshold specified by the value of ccacSysRpMedThreshold since the last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32SinceReset  

cmedxOverloadExitCounts 1.3.6.1.4.1.9.10.104.1.2.7.1.2
The number of times that the gateway exits the overload condition when all of CAC monitoring resources have fallen below the low threshold specified by the value of ccacSysRpLowThreshold since the last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32SinceReset  

cmedxOverloadCurrentState 1.3.6.1.4.1.9.10.104.1.2.7.1.3
This object indicates the current overload state of the gateway. normal - In normal condition. overload - In overload condition.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), overload(2)  

cmedxOverloadLastResetTime 1.3.6.1.4.1.9.10.104.1.2.7.1.4
This object contains the value of sysUpTime when the last counter reset occurred by setting cmedxOverloadCountersClear to 'true'. If no counter reset has occurred since the last time the media gateway reboot, this object will contain value of zero.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cmedxOverloadCountersClear 1.3.6.1.4.1.9.10.104.1.2.7.1.5
When this object is to set value of true(1), all statistics counters in the table cmedxOverloadStatsTable will be reset to zero. Setting this object to a value of false(2) has no implication. This object will always return 'false' upon any SNMP get operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmedxOverloadResourceStatsTable 1.3.6.1.4.1.9.10.104.1.2.8
This table contains the statistics of the resource utilization when the gateway enters overload condition.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxOverloadResourceStatsEntry

cmedxOverloadResourceStatsEntry 1.3.6.1.4.1.9.10.104.1.2.8.1
Each entry contains the utilization statistics of the resource when the gateway is overloaded.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxOverloadResourceStatsEntry  

cmedxOverloadRsResourceIndex 1.3.6.1.4.1.9.10.104.1.2.8.1.1
This object uniquely identifies the utilization of the resource is monitored for the gateway overload. The value of 0 is to sum the individual statistical counter for all the monitored resources.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..1000  

cmedxOverloadRsHighCounts 1.3.6.1.4.1.9.10.104.1.2.8.1.2
The accumulated number of times that the utilization of the resource is above the high threshold specified by ccacSysRpHighThreshold when the gateway enters the overload condition since the last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32SinceReset  

cmedxOverloadRsMedCounts 1.3.6.1.4.1.9.10.104.1.2.8.1.3
The accumulated number of times that the utilization of the resource is above the medium threshold specified by ccacSysRpMedThreshold when the gateway enters the overload condition since the last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32SinceReset  

cmedxOverloadRsLowCounts 1.3.6.1.4.1.9.10.104.1.2.8.1.4
The accumulated number of times that the utilization of the resource is above the low threshold specified by ccacSysRpLowThreshold when the gateway enters the overload condition since the last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32SinceReset  

cmedxOverloadContributorCounts 1.3.6.1.4.1.9.10.104.1.2.8.1.5
The accumulated number of times the CAC monitoring resource causes the gateway entering the overload condition since the last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32SinceReset  

cmedxOverloadRsLastResetTime 1.3.6.1.4.1.9.10.104.1.2.8.1.6
This object contains the value of sysUpTime when the last counter reset occurred by setting cmedxOverloadRsCountersClear to 'true'. If no counter reset has occurred since the last time the media gateway reboot, this object will contain value of zero.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

cmedxOverloadRsCountersClear 1.3.6.1.4.1.9.10.104.1.2.8.1.7
When this object is to set value of true(1), all statistics counters in the table cmedxOverloadResourceStatsTable will be reset to zero. Setting this object to a value of false(2) has no implication. This object will always return 'false' upon any SNMP get operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmedxEphemeralTermStatsInfoTable 1.3.6.1.4.1.9.10.104.1.2.9
This table contains statistics information related to ephemeral terminations.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CmedxEphemeralTermStatsInfoEntry

cmedxEphemeralTermStatsInfoEntry 1.3.6.1.4.1.9.10.104.1.2.9.1
Each entry contains the ephemeral termination statistics inforamtion for a specific level.
Status: current Access: not-accessible
OBJECT-TYPE    
  CmedxEphemeralTermStatsInfoEntry  

cmedxEphTermInfoStatsIndex 1.3.6.1.4.1.9.10.104.1.2.9.1.1
This object uniquely identifies the entry to store ephemeral termination statistics information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..2147483647  

cmedxEphTermInfoStatsIndexType 1.3.6.1.4.1.9.10.104.1.2.9.1.2
This object is used to indicate index ('cmedxEphTermInfoStatsIndex') type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER bpvc(1), gw(2), vgw(3)  

cmedxEphTermInfoNumTerm 1.3.6.1.4.1.9.10.104.1.2.9.1.3
The accumulated number of ephemeral termination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32SinceReset  

cmedxEphTermInfoNumInUsed 1.3.6.1.4.1.9.10.104.1.2.9.1.4
The number of ephemeral termination currently in use.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxEphTermInfoMaxNumInUsed 1.3.6.1.4.1.9.10.104.1.2.9.1.5
The high watermark of number of ephemeral termination in use.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxEphTermInfoMinDuration 1.3.6.1.4.1.9.10.104.1.2.9.1.6
The minimum duration of ephemeral termination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxEphTermInfoMaxDuration 1.3.6.1.4.1.9.10.104.1.2.9.1.7
The maximum duration of ephemeral termination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxEphTermInfoAvgDuration 1.3.6.1.4.1.9.10.104.1.2.9.1.8
The average duration of ephemeral termination.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

cmedxEphTermInfoCounterClear 1.3.6.1.4.1.9.10.104.1.2.9.1.9
When this object is set to value of true(1), all statistics counters with type of Counter32SinceReset in this table will be reset to zero. Setting this object to a value of false(2) has no implication. This object will always return 'false' upon any SNMP get operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cmedxEphTermInfoSinceLastClear 1.3.6.1.4.1.9.10.104.1.2.9.1.10
The elapsed time from the last counter clear. The following objects are set to zero on the last counter clear: 'cmedxEphTermInfoNumTerm'
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cmedxEphTermInfoSinceLastReset 1.3.6.1.4.1.9.10.104.1.2.9.1.11
The elapsed time from the last reset. The following objects are set to zero on the last reset: 'cmedxEphTermInfoNumInUsed' 'cmedxEphTermInfoMaxNumInUsed' 'cmedxEphTermInfoMinDuration' 'cmedxEphTermInfoMaxDuration' 'cmedxEphTermInfoNumFreed'
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cmedxEphTermIndexInfo 1.3.6.1.4.1.9.10.104.1.2.9.1.12
This object is used to store the index ('cmedxEphTermInfoStatsIndex') related information. Example: for bpvc ('cmedxEphTermInfoStatsIndexType'), the vpi and vci are stored in this object. The value zero means this object should be ignored.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..2147483647  

cmedxEphTermInfoNumFreed 1.3.6.1.4.1.9.10.104.1.2.9.1.13
Total number of ephemeral terminations that have been freed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ciscoMegacoExtConformance 1.3.6.1.4.1.9.10.104.2
OBJECT IDENTIFIER    

cmedxCompliances 1.3.6.1.4.1.9.10.104.2.1
OBJECT IDENTIFIER    

cmedxGroups 1.3.6.1.4.1.9.10.104.2.2
OBJECT IDENTIFIER    

cmedxCompliance 1.3.6.1.4.1.9.10.104.2.1.1
Compliance statement for entities which implement the CiSCO-MEGACO-EXT-MIB. This has been replaced by cmedxComplianceRev1
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

cmedxComplianceRev1 1.3.6.1.4.1.9.10.104.2.1.2
Compliance statement for entities which implement the CiSCO-MEGACO-EXT-MIB. This has been replaced by cmedxComplianceRev2.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

cmedxComplianceRev2 1.3.6.1.4.1.9.10.104.2.1.3
Compliance statement for entities which implement the CiSCO-MEGACO-EXT-MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

cmedxComplianceRev3 1.3.6.1.4.1.9.10.104.2.1.4
Compliance statement for entities which implement the CiSCO-MEGACO-EXT-MIB.
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

cmedxComplianceRev4 1.3.6.1.4.1.9.10.104.2.1.5
Compliance statement for entities which implement the CiSCO-MEGACO-EXT-MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

cmedxConfigGroup 1.3.6.1.4.1.9.10.104.2.2.1
This group contains of all the configuration extended information for a media gateway.
Status: deprecated Access: read-only
OBJECT-GROUP    

cmedxStatsGroup 1.3.6.1.4.1.9.10.104.2.2.2
This group contains of all the statistics information for the statistics in a media gateway.
Status: deprecated Access: read-only
OBJECT-GROUP    

cmedxCallReduceRateGroup 1.3.6.1.4.1.9.10.104.2.2.3
This group contains objects used to manage and/or monitor the rate at which call attempts are made by Media gateway controller on this Media Gateway.
Status: current Access: read-only
OBJECT-GROUP    

cmedxCodecNegotiationGroup 1.3.6.1.4.1.9.10.104.2.2.4
This group contains objects used for CODEC negotiation between MG and MGC.
Status: current Access: read-only
OBJECT-GROUP    

cmedxConfigExtGroup 1.3.6.1.4.1.9.10.104.2.2.5
This group contains of the objects related to Megaco message size provisioning and BellCore standard COT a media gateway.
Status: current Access: read-only
OBJECT-GROUP    

cmedxServiceStateGroup 1.3.6.1.4.1.9.10.104.2.2.6
This group contains of the objects to change the service state of a media gateway.
Status: current Access: read-only
OBJECT-GROUP    

cmedxConfigGroupRev1 1.3.6.1.4.1.9.10.104.2.2.7
This group contains of all the configuration extended information for a media gateway.
Status: deprecated Access: read-only
OBJECT-GROUP    

cmedxCallReduceRateNotifyGroup 1.3.6.1.4.1.9.10.104.2.2.8
This group contains objects used for H.248.10 congestion control notification.
Status: current Access: read-only
OBJECT-GROUP    

cmedxOverloadControlGroup 1.3.6.1.4.1.9.10.104.2.2.9
This group contains objects used for H.248.11 overload control package.
Status: current Access: read-only
OBJECT-GROUP    

cmedxOverloadStatsGroup 1.3.6.1.4.1.9.10.104.2.2.10
This group contains objects used for the statistics of H.248.11 overload control.
Status: current Access: read-only
OBJECT-GROUP    

cmedxStatsExtGroup 1.3.6.1.4.1.9.10.104.2.2.11
This group contains objects related to the extended statistics of H.248.
Status: current Access: read-only
OBJECT-GROUP    

cmedxEphemeralTermStatsGroup 1.3.6.1.4.1.9.10.104.2.2.12
This group contains objects related to ephemeral termination statistics of H.248.
Status: current Access: read-only
OBJECT-GROUP    

cmedxConfigGroupRev2 1.3.6.1.4.1.9.10.104.2.2.13
This group contains of all the configuration extended information for a media gateway.
Status: current Access: read-only
OBJECT-GROUP    

cmedxStatsGroupRev1 1.3.6.1.4.1.9.10.104.2.2.14
This group contains of all the statistics information for the statistics in a media gateway.
Status: current Access: read-only
OBJECT-GROUP    

cmedxConfigDomainInfoGroup 1.3.6.1.4.1.9.10.104.2.2.15
This group specifies the domain name and port configuration for a media gateway.
Status: current Access: read-only
OBJECT-GROUP