CISCO-LWAPP-RF-MIB

File: CISCO-LWAPP-RF-MIB.mib (41667 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB CISCO-LWAPP-TC-MIB CISCO-LWAPP-WLAN-MIB
CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Integer32 MODULE-COMPLIANCE OBJECT-GROUP
TEXTUAL-CONVENTION RowStatus TruthValue
StorageType SnmpAdminString CLApIfType
cLAPGroupName ciscoMgmt

Defined Types

CiscoLwappRFApDataRates  
This field indicates the data rates supported by an AP 'disabled' The rate is not supported by the AP 'supported' The rate is supported by the AP 'mandatoryRate' The rate is required by the AP 'notApplicable' The rate is notApplicable.
TEXTUAL-CONVENTION    
  INTEGER disabled(0), supported(1), mandatoryRate(2), notApplicable(3)  

CLAPGroupsRFProfileEntry  
SEQUENCE    
  cLAPGroups802dot11bgRFProfileName SnmpAdminString
  cLAPGroups802dot11aRFProfileName SnmpAdminString

CLRFProfileEntry  
SEQUENCE    
  cLRFProfileName SnmpAdminString
  cLRFProfileDescr SnmpAdminString
  cLRFProfileTransmitPowerMin Integer32
  cLRFProfileTransmitPowerMax Integer32
  cLRFProfileTransmitPowerThresholdV1 Integer32
  cLRFProfileTransmitPowerThresholdV2 Integer32
  cLRFProfileDataRate1Mbps CiscoLwappRFApDataRates
  cLRFProfileDataRate2Mbps CiscoLwappRFApDataRates
  cLRFProfileDataRate5AndHalfMbps CiscoLwappRFApDataRates
  cLRFProfileDataRate11Mbps CiscoLwappRFApDataRates
  cLRFProfileDataRate6Mbps CiscoLwappRFApDataRates
  cLRFProfileDataRate9Mbps CiscoLwappRFApDataRates
  cLRFProfileDataRate12Mbps CiscoLwappRFApDataRates
  cLRFProfileDataRate18Mbps CiscoLwappRFApDataRates
  cLRFProfileDataRate24Mbps CiscoLwappRFApDataRates
  cLRFProfileDataRate36Mbps CiscoLwappRFApDataRates
  cLRFProfileDataRate48Mbps CiscoLwappRFApDataRates
  cLRFProfileDataRate54Mbps CiscoLwappRFApDataRates
  cLRFProfileRadioType CLApIfType
  cLRFProfileStorageType StorageType
  cLRFProfileRowStatus RowStatus
  cLRFProfileHighDensityMaxRadioClients Unsigned32
  cLRFProfileBandSelectProbeResponse TruthValue
  cLRFProfileBandSelectCycleCount Unsigned32
  cLRFProfileBandSelectCycleThreshold Unsigned32
  cLRFProfileBandSelectExpireSuppression Unsigned32
  cLRFProfileBandSelectExpireDualBand Unsigned32
  cLRFProfileBandSelectClientRSSI Integer32
  cLRFProfileLoadBalancingWindowSize Unsigned32
  cLRFProfileLoadBalancingDenialCount Unsigned32
  cLRFProfileCHDDataRSSIThreshold Integer32
  cLRFProfileCHDVoiceRSSIThreshold Integer32
  cLRFProfileCHDClientExceptionLevel Unsigned32
  cLRFProfileCHDCoverageExceptionLevel Unsigned32
  cLRFProfileMulticastDataRate Unsigned32
  cLRFProfileHDClientTrapThreshold Unsigned32
  cLRFProfileInterferenceThreshold Unsigned32
  cLRFProfileNoiseThreshold Integer32
  cLRFProfileUtilizationThreshold Unsigned32
  cLRFProfile11nOnly TruthValue
  cLRFProfileDCAForeignContribution TruthValue
  cLRFProfileDCAChannelWidth INTEGER
  cLRFProfileDCAChannelList SnmpAdminString
  cLRFProfileRxSopThreshold INTEGER

CLRFProfileMcsDataRateEntry  
SEQUENCE    
  cLRFProfileMcsName SnmpAdminString
  cLRFProfileMcsRate Unsigned32
  cLRFProfileMcsRateSupport TruthValue

Defined Values

ciscoLwappRFMIB 1.3.6.1.4.1.9.9.778
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. This MIB helps to manage the Radio Frequency (RF) parameters on the controller. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected to. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the controllers. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. 802.1x The IEEE ratified standard for enforcing port based access control. This was originally intended for use on wired LANs and later extended for use in 802.11 WLAN environments. This defines an architecture with three main parts - a supplicant (Ex. an 802.11 wireless client), an authenticator (the AP) and an authentication server(a Radius server). The authenticator passes messages back and forth between the supplicant and the authentication server to enable the supplicant get authenticated to the network. Radio Frequency ( RF ) Radio frequency (RF) is a rate of oscillation in the range of about 3 kHz to 300 GHz, which corresponds to the frequency of radio waves, and the alternating currents which carry radio signals. Received Signal Strength Indicator ( RSSI ) A measure of the strength of the signal as observed by the entity that received it, expressed in 'dbm'. Coverage Hole Detection ( CHD ) If clients on an Access Point are detected at low RSSI levels, it is considered a coverage hole by the Access Points. This indicates the existence of an area where clients are continually getting poor signal coverage, without having a viable location to roam to. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol [3] IEEE 802.11 - The original 1 Mbit/s and 2 Mbit/s, 2.4 GHz RF and IR standard.
MODULE-IDENTITY    

ciscoLwappRFMIBNotifs 1.3.6.1.4.1.9.9.778.0
OBJECT IDENTIFIER    

ciscoLwappRFMIBObjects 1.3.6.1.4.1.9.9.778.1
OBJECT IDENTIFIER    

ciscoLwappRFMIBConform 1.3.6.1.4.1.9.9.778.2
OBJECT IDENTIFIER    

ciscoLwappRFConfig 1.3.6.1.4.1.9.9.778.1.1
OBJECT IDENTIFIER    

ciscoLwappRFGlobalObjects 1.3.6.1.4.1.9.9.778.1.2
OBJECT IDENTIFIER    

cLAPGroupsRFProfileTable 1.3.6.1.4.1.9.9.778.1.1.1
This table lists the mapping between an RF profile and an AP group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLAPGroupsRFProfileEntry

cLAPGroupsRFProfileEntry 1.3.6.1.4.1.9.9.778.1.1.1.1
An entry containing the configuration attributes that affect the operation of the APs within a group. Entries can be added/deleted by explicit management action from NMS/EMS through the 'bsnAPGroupsVlanRowStatus' object in bsnAPGroupsVlanTable as defined by the AIRESPACE-WIRELESS-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLAPGroupsRFProfileEntry  

cLAPGroups802dot11bgRFProfileName 1.3.6.1.4.1.9.9.778.1.1.1.1.1
This object specifies the RF profile name assigned to this site on the 802.11bg radio. This profile being assigned should exist in the 'cLRFProfileTable'. To disassociate a profile with this site a string of zero length should be set.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLAPGroups802dot11aRFProfileName 1.3.6.1.4.1.9.9.778.1.1.1.1.2
This object specifies the RF profile name assigned to this site on the 802.11a radio. This profile being assigned should exist in the 'cLRFProfileTable'. To disassociate a profile with this site a string of zero length should be set.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLRFProfileTable 1.3.6.1.4.1.9.9.778.1.1.2
This table lists the configuration for each RF profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLRFProfileEntry

cLRFProfileEntry 1.3.6.1.4.1.9.9.778.1.1.2.1
An entry containing the configuration attributes that affect the operation of 802.11 RF domain. Entries can be added/deleted by explicit management action from NMS/EMS or through user console.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLRFProfileEntry  

cLRFProfileName 1.3.6.1.4.1.9.9.778.1.1.2.1.1
This object uniquely identifies a RF Profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..64)  

cLRFProfileDescr 1.3.6.1.4.1.9.9.778.1.1.2.1.2
This object specifies a human-readable description of the profile.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

cLRFProfileTransmitPowerMin 1.3.6.1.4.1.9.9.778.1.1.2.1.3
This object specifies the lower bound of transmit power value supported by an AP.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -10..30  

cLRFProfileTransmitPowerMax 1.3.6.1.4.1.9.9.778.1.1.2.1.4
This object specifies the uppoer bound of transmit power value supported by an AP.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -10..30  

cLRFProfileTransmitPowerThresholdV1 1.3.6.1.4.1.9.9.778.1.1.2.1.5
This object specifies the transmit power control version 1 threshold for the radio resource management algorithm.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -80..-50  

cLRFProfileTransmitPowerThresholdV2 1.3.6.1.4.1.9.9.778.1.1.2.1.6
This object specifies the transmit power control version 2 threshold for the radio resource management algorithm.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 -80..-50  

cLRFProfileDataRate1Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.7
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate2Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.8
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate5AndHalfMbps 1.3.6.1.4.1.9.9.778.1.1.2.1.9
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate11Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.10
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate6Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.11
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate9Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.12
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate12Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.13
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate18Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.14
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate24Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.15
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate36Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.16
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate48Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.17
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileDataRate54Mbps 1.3.6.1.4.1.9.9.778.1.1.2.1.18
This object specifies the configuration for this data rate.
Status: current Access: read-create
OBJECT-TYPE    
  CiscoLwappRFApDataRates  

cLRFProfileRadioType 1.3.6.1.4.1.9.9.778.1.1.2.1.19
This object is used to configure the radio type for this profile.
Status: current Access: read-create
OBJECT-TYPE    
  CLApIfType  

cLRFProfileStorageType 1.3.6.1.4.1.9.9.778.1.1.2.1.20
This object represents the storage type for this conceptual row.
Status: current Access: read-create
OBJECT-TYPE    
  StorageType  

cLRFProfileRowStatus 1.3.6.1.4.1.9.9.778.1.1.2.1.21
This is the status column for this row and used to create and delete specific instances of rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLRFProfileHighDensityMaxRadioClients 1.3.6.1.4.1.9.9.778.1.1.2.1.22
This object specifies the maximum number of clients per AP radio.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfileBandSelectProbeResponse 1.3.6.1.4.1.9.9.778.1.1.2.1.23
This object specifies the AP's probe response with clients to verify whether client can associate on both 2.4 GHz and 5Ghz spectrum. When set to true, AP suppresses probe response to new clients for all SSIDs that are not being Band Select disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLRFProfileBandSelectCycleCount 1.3.6.1.4.1.9.9.778.1.1.2.1.24
This object specifies the maximum number of cycles not responding.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfileBandSelectCycleThreshold 1.3.6.1.4.1.9.9.778.1.1.2.1.25
This object specifies the cycle threshold for band select.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfileBandSelectExpireSuppression 1.3.6.1.4.1.9.9.778.1.1.2.1.26
This object specifies the expire of suppression.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfileBandSelectExpireDualBand 1.3.6.1.4.1.9.9.778.1.1.2.1.27
This object specifies the expire of dual band.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfileBandSelectClientRSSI 1.3.6.1.4.1.9.9.778.1.1.2.1.28
This object specifies the minimum dBM of a client RSSI to respond to probe.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cLRFProfileLoadBalancingWindowSize 1.3.6.1.4.1.9.9.778.1.1.2.1.29
This object specifies the number of clients associated between APs.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfileLoadBalancingDenialCount 1.3.6.1.4.1.9.9.778.1.1.2.1.30
This object specifies number of clients denial with respect to AP.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfileCHDDataRSSIThreshold 1.3.6.1.4.1.9.9.778.1.1.2.1.31
This object specifies the RSSI threshold value for data packets.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cLRFProfileCHDVoiceRSSIThreshold 1.3.6.1.4.1.9.9.778.1.1.2.1.32
This object specifies RSSI threshold value for voice packets.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cLRFProfileCHDClientExceptionLevel 1.3.6.1.4.1.9.9.778.1.1.2.1.33
This object specifies the client minimum exception level.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfileCHDCoverageExceptionLevel 1.3.6.1.4.1.9.9.778.1.1.2.1.34
This object specifies the coverage exception level.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfileMulticastDataRate 1.3.6.1.4.1.9.9.778.1.1.2.1.35
This object specifies the minimum multicast data rate. A value 0 indicates that AP will automatically adjust data rates.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfile11nOnly 1.3.6.1.4.1.9.9.778.1.1.2.1.36
This object specifies if 11n-client-only mode is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

cLRFProfileHDClientTrapThreshold 1.3.6.1.4.1.9.9.778.1.1.2.1.37
This object specifies the threshold number of clients per AP radio to trigger a trap. The trap ciscoLwappApClientThresholdNotify will be triggered once the count of clients on the AP radio reaches this limit. A value of zero indicates that the trap is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

cLRFProfileInterferenceThreshold 1.3.6.1.4.1.9.9.778.1.1.2.1.38
This object specifies the threshold number of interference between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

cLRFProfileNoiseThreshold 1.3.6.1.4.1.9.9.778.1.1.2.1.39
This object specifies the threshold number of noise threshold between -127 and 0 dBm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -127..0  

cLRFProfileUtilizationThreshold 1.3.6.1.4.1.9.9.778.1.1.2.1.40
This object specifies the threshold number of utlization threshold between 0 and 100 percent.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..100  

cLRFProfileDCAForeignContribution 1.3.6.1.4.1.9.9.778.1.1.2.1.41
This object specifies whether foreign interference is taken into account for the DCA metrics.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLRFProfileDCAChannelWidth 1.3.6.1.4.1.9.9.778.1.1.2.1.42
This object specifies how the system performs DCA channel width selection for the RFProfile min - Min channel width(20Mhz) the radio supports medium - Medium channel width(40Mhz) supported by this radio. max - Max channel width(80Mhz) supported by this radio.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER min(1), medium(2), max(3)  

cLRFProfileDCAChannelList 1.3.6.1.4.1.9.9.778.1.1.2.1.43
This object specifies the 802.11 channels available to the RF Profile. A comma separated list of integers.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(1..500)  

cLRFProfileRxSopThreshold 1.3.6.1.4.1.9.9.778.1.1.2.1.44
Configures the receiver start of packet threshold for the rf profile.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(0), low(1), medium(2), high(3)  

cLRFProfileOutOfBoxAPConfig 1.3.6.1.4.1.9.9.778.1.2.1
This object specifies the out of box AP group.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

cLRFProfileMcsDataRateTable 1.3.6.1.4.1.9.9.778.1.1.3
This object specifies the 11n MCS rates supported by the RF profile, indexed by the MCS rate, ranging from 1 to 24, corresponding to rate MCS-0, MCS-1, ... MCS-23.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLRFProfileMcsDataRateEntry

cLRFProfileMcsDataRateEntry 1.3.6.1.4.1.9.9.778.1.1.3.1
An entry containing MCS date rate information applicable to a particular profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLRFProfileMcsDataRateEntry  

cLRFProfileMcsName 1.3.6.1.4.1.9.9.778.1.1.3.1.1
This object uniquely identifies a RF Profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..64)  

cLRFProfileMcsRate 1.3.6.1.4.1.9.9.778.1.1.3.1.2
This object uniquely identifies the MCS data rate for a particular profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

cLRFProfileMcsRateSupport 1.3.6.1.4.1.9.9.778.1.1.3.1.3
This object is used to enable or disable the data rate. When this object is set to 'true' the MCS support is enabled. When this object is set to 'false' the MCS support is disabled..
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ciscoLwappRFMIBCompliances 1.3.6.1.4.1.9.9.778.2.1
OBJECT IDENTIFIER    

ciscoLwappRFMIBGroups 1.3.6.1.4.1.9.9.778.2.2
OBJECT IDENTIFIER    

ciscoLwappRFMIBCompliance 1.3.6.1.4.1.9.9.778.2.1.1
The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. This compliance is deprecated and replaced by ciscoLwappRFMIBComplianceVer1 .
Status: deprecated Access: read-write
MODULE-COMPLIANCE    

ciscoLwappRFMIBComplianceVer1 1.3.6.1.4.1.9.9.778.2.1.2
The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module.
Status: current Access: read-write
MODULE-COMPLIANCE    

ciscoLwappRFMIBComplianceVer2 1.3.6.1.4.1.9.9.778.2.1.3
The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. Added ciscoLwappRFConfigGroup2 to add object to raise trap when client count exceeds threshold and ciscoLwappRFConfigGroup3 to address DCA settings
Status: current Access: read-write
MODULE-COMPLIANCE    

ciscoLwappRFConfigGroup 1.3.6.1.4.1.9.9.778.2.2.1
This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.This config group ciscoLwappRFConfigGroup is deprecated and replaced by ciscoLwappRFConfigGroupVer1
Status: deprecated Access: read-write
OBJECT-GROUP    

ciscoLwappRFConfigGroupVer1 1.3.6.1.4.1.9.9.778.2.2.2
This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.
Status: current Access: read-write
OBJECT-GROUP    

ciscoLwappRFConfigGroup1 1.3.6.1.4.1.9.9.778.2.2.5
This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.
Status: current Access: read-write
OBJECT-GROUP    

ciscoLwappRFGlobalConfigGroup 1.3.6.1.4.1.9.9.778.2.2.3
This is the RF global config parameter.
Status: current Access: read-write
OBJECT-GROUP    

ciscoLwappRFConfigGroup2 1.3.6.1.4.1.9.9.778.2.2.4
This object specifies the configuration of Trap threshold to be configured on the interface of an LWAPP AP.
Status: current Access: read-write
OBJECT-GROUP    

ciscoLwappRFConfigGroup3 1.3.6.1.4.1.9.9.778.2.2.6
This object specifies the configuration DCA for RF Profiles.
Status: current Access: read-write
OBJECT-GROUP    

ciscoLwappRFConfigGroup4 1.3.6.1.4.1.9.9.778.2.2.7
This object specifies the receiver start of packet threshold for RF Profiles.
Status: current Access: read-write
OBJECT-GROUP