CISCO-LWAPP-PMIP-MIB

File: CISCO-LWAPP-PMIP-MIB.mib (28858 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB INET-ADDRESS-MIB CISCO-LWAPP-WLAN-MIB
CISCO-LWAPP-DOT11-CLIENT-MIB CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Unsigned32 Counter32 TimeTicks
Gauge32 Integer32 MODULE-COMPLIANCE
NOTIFICATION-GROUP OBJECT-GROUP DisplayString
TruthValue MacAddress TimeInterval
RowStatus TimeStamp SnmpAdminString
InetAddressType InetAddress InetPortNumber
cLWlanIndex cldcClientMacAddress ciscoMgmt

Defined Types

CLPmipLmaEntry  
SEQUENCE    
  cLPmipLmaName SnmpAdminString
  cLPmipLmaIPAddrType InetAddressType
  cLPmipLmaIPAddr InetAddress
  cLPmipLmaRowStatus RowStatus

CLPmipLmaStatsEntry  
SEQUENCE    
  cLPmipLmaTotalBindings Counter32
  cLPmipLmaPbuSent Counter32
  cLPmipLmaPbaReceived Counter32
  cLPmipLmaPbriSent Counter32
  cLPmipLmaPbriReceived Counter32
  cLPmipLmaPbraSent Counter32
  cLPmipLmaPbraReceived Counter32
  cLPmipLmaNoOfHandoff Counter32
  cLPmipLmaPbuDropped Counter32

CLPmipProfileEntry  
SEQUENCE    
  cLPmipProfileName SnmpAdminString

CLPmipProfileNaiEntry  
SEQUENCE    
  cLPmipProfileNai SnmpAdminString
  cLPmipProfileApn SnmpAdminString
  cLPmipProfileLmaName SnmpAdminString
  cLPmipProfileNaiRowStatus RowStatus

CLPmipWlanEntry  
SEQUENCE    
  cLPmipWlanProfileName SnmpAdminString
  cLPmipWlanMobilityType INTEGER
  cLPmipWlanDefaultRealm SnmpAdminString

CLPmipClientInfoEntry  
SEQUENCE    
  cLPmipClientNai SnmpAdminString
  cLPmipClientState SnmpAdminString
  cLPmipClientInterface SnmpAdminString
  cLPmipClientHomeAddressType InetAddressType
  cLPmipClientHomeAddress InetAddress
  cLPmipClientAtt INTEGER
  cLPmipClientLocalLinkId MacAddress
  cLPmipClientLmaName SnmpAdminString
  cLPmipClientLifeTime TimeTicks
  cLPmipClientDomainName SnmpAdminString
  cLPmipClientUpKey Unsigned32
  cLPmipClientDownKey Unsigned32

Defined Values

ciscoLwappPmipMIB 1.3.6.1.4.1.9.9.888
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information about local mobility anchor to which the controller has the joined. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + LMA + + LMA + + LMA + + LMA + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + WLC + + WLC + + WLC + + WLC + + WLC + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
MODULE-IDENTITY    

ciscoLwappPmipMIBObjects 1.3.6.1.4.1.9.9.888.0
OBJECT IDENTIFIER    

ciscoLwappPmipGlobal 1.3.6.1.4.1.9.9.888.0.1
OBJECT IDENTIFIER    

ciscoLwappPmipConfig 1.3.6.1.4.1.9.9.888.0.2
OBJECT IDENTIFIER    

ciscoLwappPmipStatistics 1.3.6.1.4.1.9.9.888.0.3
OBJECT IDENTIFIER    

cLPmipDomainName 1.3.6.1.4.1.9.9.888.0.1.1
This object specifies the domain name to which the controller belongs.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

cLPmipMAGInterface 1.3.6.1.4.1.9.9.888.0.1.2
This object specifies the interface to which the LMAs communicate.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

cLPmipMaxBindings 1.3.6.1.4.1.9.9.888.0.1.3
This object indicates the number of binding updates sent by the controller.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLPmipBindingLifeTime 1.3.6.1.4.1.9.9.888.0.1.4
This object indicates the lifetime of the binding entries maintained by the controller.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

cLPmipBindingRefreshTime 1.3.6.1.4.1.9.9.888.0.1.5
This object indicates the refresh time for the binding entries maintained by the controller.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

cLPmipBindingInitRetxTime 1.3.6.1.4.1.9.9.888.0.1.6
This object indicates the initial timeout between proxy binding updates if the proxy binding ack does not arrive at the controller.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

cLPmipBindingMaxRetxTime 1.3.6.1.4.1.9.9.888.0.1.7
This object indicates the maximum timeout between proxy binding updates if the proxy binding ack does not arrive at the controller.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

cLPmipReplayProtectionTimestamp 1.3.6.1.4.1.9.9.888.0.1.8
This object specifies the maximum amount of time difference between the timestamp in the received proxy binding ack and the current time of the day.
Status: current Access: read-write
OBJECT-TYPE    
  TimeStamp  

cLPmipBriMinDelayTime 1.3.6.1.4.1.9.9.888.0.1.9
This object specifies the minimum amount of time the controller should wait before retransmitting the BRI message.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

cLPmipBriMaxDelayTime 1.3.6.1.4.1.9.9.888.0.1.10
This object specifies the maximum amount of time the controller should wait before retransmitting the BRI message.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

cLPmipBriRetries 1.3.6.1.4.1.9.9.888.0.1.11
This object specifies the maximum number of times the controller retransmits the BRI message before receiving the BRA message.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

cLPmipMagApnName 1.3.6.1.4.1.9.9.888.0.1.12
This object specifies the MAG APN name for PMIPv6 MAG on AP.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

cLPmipLmaTable 1.3.6.1.4.1.9.9.888.0.2.1
This table represents the information about the details of local mobility anchors connected to the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLPmipLmaEntry

cLPmipLmaEntry 1.3.6.1.4.1.9.9.888.0.2.1.1
An entry in this table represents the details of local mobility anchors connected to the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLPmipLmaEntry  

cLPmipLmaName 1.3.6.1.4.1.9.9.888.0.2.1.1.1
This object indicates the name of the LMA connected to the controller.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

cLPmipLmaIPAddrType 1.3.6.1.4.1.9.9.888.0.2.1.1.2
This object indicates the LMA's IP address type, made available through cLPmipLmaIPAddr.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

cLPmipLmaIPAddr 1.3.6.1.4.1.9.9.888.0.2.1.1.3
This object indicates the LMA's IP address.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

cLPmipLmaRowStatus 1.3.6.1.4.1.9.9.888.0.2.1.1.4
This object is used to add or delete an entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLPmipLmaStatsTable 1.3.6.1.4.1.9.9.888.0.3.1
This table represents the information about the LMAs that are connected to the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLPmipLmaStatsEntry

cLPmipLmaStatsEntry 1.3.6.1.4.1.9.9.888.0.3.1.1
Each entry in this table provides statistical information about the Local Mobility Anchors that are connected to the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLPmipLmaStatsEntry  

cLPmipLmaTotalBindings 1.3.6.1.4.1.9.9.888.0.3.1.1.1
This object represents total number of bindings sent to the LMA by the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLPmipLmaPbuSent 1.3.6.1.4.1.9.9.888.0.3.1.1.2
This object represents total number of proxy binding units sent to the LMA by the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLPmipLmaPbaReceived 1.3.6.1.4.1.9.9.888.0.3.1.1.3
This object represents total number of proxy binding acks received for this LMA by the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLPmipLmaPbriSent 1.3.6.1.4.1.9.9.888.0.3.1.1.4
This object represents total number of pbri sent by the controller to the LMA
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLPmipLmaPbriReceived 1.3.6.1.4.1.9.9.888.0.3.1.1.5
This object represents total number of pbri received from the LMA by the controller.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLPmipLmaPbraSent 1.3.6.1.4.1.9.9.888.0.3.1.1.6
This object represents total number of pbra sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLPmipLmaPbraReceived 1.3.6.1.4.1.9.9.888.0.3.1.1.7
This object represents total number of pbra received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLPmipLmaNoOfHandoff 1.3.6.1.4.1.9.9.888.0.3.1.1.8
This object represents number of hand offs between the controller and the LMA.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLPmipLmaPbuDropped 1.3.6.1.4.1.9.9.888.0.3.1.1.9
This object represents number of pbus dropped between the controller and the LMA.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

cLPmipProfileTable 1.3.6.1.4.1.9.9.888.0.2.2
This table represents the information about the details of PMIP profiles created on the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLPmipProfileEntry

cLPmipProfileEntry 1.3.6.1.4.1.9.9.888.0.2.2.1
An entry in this table represents the details of PMIP profiles created on the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLPmipProfileEntry  

cLPmipProfileName 1.3.6.1.4.1.9.9.888.0.2.2.1.1
This object indicates the name of the profile.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cLPmipProfileNaiTable 1.3.6.1.4.1.9.9.888.0.2.3
This table represents the information about the details of PMIP profiles created in the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLPmipProfileNaiEntry

cLPmipProfileNaiEntry 1.3.6.1.4.1.9.9.888.0.2.3.1
An entry in this table represents the details of PMIP profiles created in the controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLPmipProfileNaiEntry  

cLPmipProfileNai 1.3.6.1.4.1.9.9.888.0.2.3.1.1
This object indicates the name of the nai string assocaited with this profile.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

cLPmipProfileApn 1.3.6.1.4.1.9.9.888.0.2.3.1.2
This object indicates the name of the access point node connected to the controller.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

cLPmipProfileLmaName 1.3.6.1.4.1.9.9.888.0.2.3.1.3
This object indicates the name of the LMA to which the profile is associated to.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

cLPmipProfileNaiRowStatus 1.3.6.1.4.1.9.9.888.0.2.3.1.4
This object is used to add or delete an entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cLPmipWlanTable 1.3.6.1.4.1.9.9.888.0.2.4
This table represents the generic PMIP configuration for a particular WLAN in a controller. This table has a one-to-one relationship with cLWlanConfigTable. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLPmipWlanEntry

cLPmipWlanEntry 1.3.6.1.4.1.9.9.888.0.2.4.1
Each entry in this table represents the generic PMIP configuration for a WLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLPmipWlanEntry  

cLPmipWlanProfileName 1.3.6.1.4.1.9.9.888.0.2.4.1.1
This object indicates the name of the profile associated to this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

cLPmipWlanMobilityType 1.3.6.1.4.1.9.9.888.0.2.4.1.2
This object specifies the mobility type of the clients associated to this particular WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), pmipv6(2)  

cLPmipWlanDefaultRealm 1.3.6.1.4.1.9.9.888.0.2.4.1.3
This object indicates the name of the default realm associated to this WLAN.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

cLPmipClientInfoTable 1.3.6.1.4.1.9.9.888.0.3.2
This table represents the PMIP information of the clients associated to this controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CLPmipClientInfoEntry

cLPmipClientInfoEntry 1.3.6.1.4.1.9.9.888.0.3.2.1
Each entry in this table represents the generic PMIP information for a client.
Status: current Access: not-accessible
OBJECT-TYPE    
  CLPmipClientInfoEntry  

cLPmipClientNai 1.3.6.1.4.1.9.9.888.0.3.2.1.1
This object indicates the name of the profile, the client is associated to.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cLPmipClientState 1.3.6.1.4.1.9.9.888.0.3.2.1.2
This object indicates the state of the PMIP client: null: binding doesn't exist init: binding created, Retx timer running for PBU, binding not yet accepted from LMA, Tunnel/route is not yet setup active: binding accepted by LMA, refresh timer running, Tunnel/route setup complete. refreshPending: Refresh timer expired and Retx timer running. PBU refresh sent, PBA not yet received from LMA, (Tunnel/route is already setup). disconnectingSt: Dereg reply is expected. Retx timer is running, tunnel/route is still setup.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cLPmipClientInterface 1.3.6.1.4.1.9.9.888.0.3.2.1.3
This object indicates the interface to which the client is associated.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

cLPmipClientHomeAddressType 1.3.6.1.4.1.9.9.888.0.3.2.1.4
This object indicates the type of the Client's Home address made available through cLPmipClientHomeAddress.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

cLPmipClientHomeAddress 1.3.6.1.4.1.9.9.888.0.3.2.1.5
This object indicates the Home Address of the client.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

cLPmipClientAtt 1.3.6.1.4.1.9.9.888.0.3.2.1.6
This object indicates the access technology type by which the client is currently attached.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reserved(0), logicalNetworkInterface(1), pointToPointInterface(2), ethernet(3), wirelessLan(4), wimax(5), threeGPPGERAN(6), threeGPPUTRAN(7), threeGPPETRAN(8), threeGPP2eHRPD(9), threeGPP2HRPD(10), threeGPP21xRTT(11), threeGPP2UMB(12)  

cLPmipClientLocalLinkId 1.3.6.1.4.1.9.9.888.0.3.2.1.7
This object indicates the local link identifier of the client.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

cLPmipClientLmaName 1.3.6.1.4.1.9.9.888.0.3.2.1.8
This object indicates the LMA to which the client is connected.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cLPmipClientLifeTime 1.3.6.1.4.1.9.9.888.0.3.2.1.9
This object indicates the duration of the PMIP client association.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

cLPmipClientDomainName 1.3.6.1.4.1.9.9.888.0.3.2.1.10
This object indicates the domain to which the PMIP client is associated.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

cLPmipClientUpKey 1.3.6.1.4.1.9.9.888.0.3.2.1.11
This object indicates the upstream key of the PMIP client.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cLPmipClientDownKey 1.3.6.1.4.1.9.9.888.0.3.2.1.12
This object indicates the downstream key of the PMIP client.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32