CISCO-ATM-CONN-MIB

File: CISCO-ATM-CONN-MIB.mib (97662 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	IF-MIB
ATM-MIB	CISCO-ATM-IF-MIB	CISCO-SMI
SNMPv2-CONF	CISCO-ATM-RM-MIB	SNMP-FRAMEWORK-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Counter32
Integer32	Gauge32	TEXTUAL-CONVENTION
TimeStamp	TruthValue	RowStatus
ifIndex	InterfaceIndexOrZero	atmVplVpi
atmVclVpi	atmVclVci	AtmTrafficDescrParamIndex
NsapAtmAddr	ciscoExperiment	MODULE-COMPLIANCE
OBJECT-GROUP	LsPerVcqThresholdGroup	SnmpAdminString

Defined Types

CastType
Specifies the type of the connection. It can be either a point to point connection or point to multipoint root or leaf.
TEXTUAL-CONVENTION
	INTEGER	pointToPoint(1), pointToMultiPointRoot(2), pointToMultiPointLeaf(3)

ConfigType
Specifies whether it's a permanent, switched, soft or soft passive config type.
TEXTUAL-CONVENTION
	INTEGER	other(1), permanent(2), switch(3), soft(4), softPassive(5)

SpanType
The SpanType textual convention is used to specify different connection span types. The connection span types are: - 'unknown', which indicates that the connection entry is not cross-connected. - 'transit', which indicates that the connection entry is cross-connected and is not a connection end point. - 'terminate', which indicates that the connection entry is cross-connected and is a connection end point. - 'both', which indicates that the connection is transit as well as terminating. This will be true only if the connection cast type is a pointToMultiPointRoot and has transit and terminating connection leaves. None of the above values may be specified in a management protocol set operation.
TEXTUAL-CONVENTION
	INTEGER	unknown(1), transit(2), terminate(3), both(4)

EnableStatus
Enable or Disable operation.
TEXTUAL-CONVENTION
	INTEGER	enable(1), disable(2)

UpcStatus
Define the Usage Parameter Control (UPC) operation as one of pass,tag or drop at this connection.
TEXTUAL-CONVENTION
	INTEGER	passing(1), tagging(2), dropping(3), localShaping(4)

ConnState
The ConnState textual convention is used to specify different connection states. The connections states are: - 'setup', which indicates that the connection entry is to be created and installed in the hardware and software connection tables. - 'release', which indicates that the connection entry is to be removed from the hardware and software connection tables. - 'notInstalled', which indicates connection entry is created only in the software connection tables. The connection entry is not installed in the hardware connection table. - 'down' which indicates that connection is down and is present in both software and hardware connection tables. - 'up' which indicates that connection is up and is present in both software and hardware connection tables. - 'setup' and 'release' are only two values may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notInstalled', 'down' or 'up'.
TEXTUAL-CONVENTION
	INTEGER	setup(1), release(2), notInstalled(3), down(4), up(5)

Location
Location of calling or called or unknown.
TEXTUAL-CONVENTION
	INTEGER	unknown(1), calling(2), called(3)

Direction
Calling or called side associated with address.
TEXTUAL-CONVENTION
	INTEGER	unknown(1), p2pCallingSide(2), p2pCalledSide(3), p2mpRoot(4), p2mpLeaf(5)

SnoopDirType
Direction of Snooped Traffic
TEXTUAL-CONVENTION
	INTEGER	transmit(1), receive(2)

CiscoAtmVplEntry
SEQUENCE
	ciscoAtmVplCastType	CastType
	ciscoAtmVplSpanType	SpanType
	ciscoAtmVplConfigType	ConfigType
	ciscoAtmVplRxUpcMode	UpcStatus
	ciscoAtmVplConnState	ConnState
	ciscoAtmVplOamLoopbkTxInterval	Integer32
	ciscoAtmVplOamSegmentLoopback	EnableStatus
	ciscoAtmVplOamEndLoopback	EnableStatus
	ciscoAtmVplOamAisEnable	EnableStatus
	ciscoAtmVplOamRdiEnable	EnableStatus
	ciscoAtmVplInstallTime	TimeStamp
	ciscoAtmVplInCells	Counter32
	ciscoAtmVplOutCells	Counter32
	ciscoAtmVplCrossIfIndex	InterfaceIndexOrZero
	ciscoAtmVplCrossVpi	Integer32
	ciscoAtmVplNextLeafIfIndex	InterfaceIndexOrZero
	ciscoAtmVplNextLeafVpi	Integer32
	ciscoAtmVplRemoteAddr	NsapAtmAddr
	ciscoAtmVplRemoteVpi	Integer32
	ciscoAtmVplLocation	Location
	ciscoAtmVplSlowRetryIntv	Integer32
	ciscoAtmVplNumAttempts	Counter32
	ciscoAtmVplLastReleaseCause	Integer32
	ciscoAtmVplLogicalPortDef	INTEGER
	ciscoAtmVplLogicalPortIndex	InterfaceIndexOrZero
	ciscoAtmVplUpcViolations	Counter32
	ciscoAtmVplEpdTpdCellDrops	Counter32
	ciscoAtmVplEpdTpdPacketDrops	Counter32
	ciscoAtmVplEpdTpdPacketsIn	Counter32
	ciscoAtmVplClp1Drops	Counter32
	ciscoAtmVplDefaultRxUpcTolerance	Integer32
	ciscoAtmVplDefaultRxUpcVbrCdvt	Integer32
	ciscoAtmVplLsPerVcqWrrWeight	INTEGER
	ciscoAtmVplLsPerVcqTunnelIsShaped	TruthValue
	ciscoAtmVplLsPerVcqXmtQueuedCells	Gauge32
	ciscoAtmVplLsPerVcQThreshGrp	LsPerVcqThresholdGroup
	ciscoAtmVplInClp0Cells	Counter32
	ciscoAtmVplInClp1Cells	Counter32
	ciscoAtmVplOutClp0Cells	Counter32
	ciscoAtmVplOutClp1Cells	Counter32
	ciscoAtmVplCellDrops	Counter32
	ciscoAtmVplClp0VcqFullCellDrops	Counter32
	ciscoAtmVplVcqClpThreshCellDrops	Counter32
	ciscoAtmVplLsPerVcqTunnelIsHierarchical	TruthValue
	ciscoAtmVplRxNegTraffDescrIndex	AtmTrafficDescrParamIndex
	ciscoAtmVplTxNegTraffDescrIndex	AtmTrafficDescrParamIndex
	ciscoAtmVplSwFabOutCells	Counter32
	ciscoAtmVplSwFabOutClp0Cells	Counter32
	ciscoAtmVplSwFabOutClp1Cells	Counter32
	ciscoAtmVplConnName	SnmpAdminString
	ciscoAtmVplConnType	INTEGER

CiscoAtmVclEntry
SEQUENCE
	ciscoAtmVclCastType	CastType
	ciscoAtmVclSpanType	SpanType
	ciscoAtmVclConfigType	ConfigType
	ciscoAtmVclRxUpcMode	UpcStatus
	ciscoAtmVclEpdEnable	INTEGER
	ciscoAtmVclConnState	ConnState
	ciscoAtmVclOamLoopbkTxInterval	Integer32
	ciscoAtmVclOamSegmentLoopback	EnableStatus
	ciscoAtmVclOamEndLoopback	EnableStatus
	ciscoAtmVclOamAisEnable	EnableStatus
	ciscoAtmVclOamRdiEnable	EnableStatus
	ciscoAtmVclInstallTime	TimeStamp
	ciscoAtmVclInCells	Counter32
	ciscoAtmVclOutCells	Counter32
	ciscoAtmVclCrossIfIndex	InterfaceIndexOrZero
	ciscoAtmVclCrossVpi	Integer32
	ciscoAtmVclCrossVci	Integer32
	ciscoAtmVclNextLeafIfIndex	InterfaceIndexOrZero
	ciscoAtmVclNextLeafVpi	Integer32
	ciscoAtmVclNextLeafVci	Integer32
	ciscoAtmVclAalEncapFlag	INTEGER
	ciscoAtmVclAalEncapProtocol	INTEGER
	ciscoAtmVclAalUserVcType	INTEGER
	ciscoAtmVclAtmInArpInterval	Integer32
	ciscoAtmVclRemoteAddr	NsapAtmAddr
	ciscoAtmVclRemoteVpi	Integer32
	ciscoAtmVclRemoteVci	Integer32
	ciscoAtmVclLocation	Location
	ciscoAtmVclSlowRetryIntv	Integer32
	ciscoAtmVclNumAttempts	Counter32
	ciscoAtmVclLastReleaseCause	Integer32
	ciscoAtmVclUpcViolations	Counter32
	ciscoAtmVclEpdTpdCellDrops	Counter32
	ciscoAtmVclEpdTpdPacketDrops	Counter32
	ciscoAtmVclEpdTpdPacketsIn	Counter32
	ciscoAtmVclClp1Drops	Counter32
	ciscoAtmVclDefaultRxUpcTolerance	Integer32
	ciscoAtmVclDefaultRxUpcVbrCdvt	Integer32
	ciscoAtmVclLsPerVcqWrrWeight	INTEGER
	ciscoAtmVclLsPerVcqXmtQueuedCells	Gauge32
	ciscoAtmVclLsPerVcQThreshGrp	LsPerVcqThresholdGroup
	ciscoAtmVclInClp0Cells	Counter32
	ciscoAtmVclInClp1Cells	Counter32
	ciscoAtmVclOutClp0Cells	Counter32
	ciscoAtmVclOutClp1Cells	Counter32
	ciscoAtmVclCellDrops	Counter32
	ciscoAtmVclClp0VcqFullCellDrops	Counter32
	ciscoAtmVclVcqClpThreshCellDrops	Counter32
	ciscoAtmVclRxNegTraffDescrIndex	AtmTrafficDescrParamIndex
	ciscoAtmVclTxNegTraffDescrIndex	AtmTrafficDescrParamIndex
	ciscoAtmVclSwFabOutCells	Counter32
	ciscoAtmVclSwFabOutClp0Cells	Counter32
	ciscoAtmVclSwFabOutClp1Cells	Counter32
	ciscoAtmVclConnName	SnmpAdminString
	ciscoAtmVclConnType	INTEGER

CiscoAtmSvpAddrEntry
SEQUENCE
	ciscoAtmSvpAddr	OCTET STRING
	ciscoAtmSvpVpi	INTEGER
	ciscoAtmSvpDirection	Direction

CiscoAtmSvcAddrEntry
SEQUENCE
	ciscoAtmSvcAddr	OCTET STRING
	ciscoAtmSvcVpi	Integer32
	ciscoAtmSvcVci	Integer32
	ciscoAtmSvcDirection	Direction

CiscoAtmSnoopVcEntry
SEQUENCE
	ciscoAtmSnoopVcSnoopedIfIndex	InterfaceIndexOrZero
	ciscoAtmSnoopVcSnoopedVpi	Integer32
	ciscoAtmSnoopVcSnoopedVci	Integer32
	ciscoAtmSnoopVcDir	SnoopDirType
	ciscoAtmSnoopVcState	ConnState
	ciscoAtmSnoopVcRowStatus	RowStatus

CiscoAtmSnoopVpEntry
SEQUENCE
	ciscoAtmSnoopVpSnoopedIfIndex	InterfaceIndexOrZero
	ciscoAtmSnoopVpSnoopedVpi	Integer32
	ciscoAtmSnoopVpDir	SnoopDirType
	ciscoAtmSnoopVpState	ConnState
	ciscoAtmSnoopVpRowStatus	RowStatus

Defined Values

ciscoAtmConnMIB		1.3.6.1.4.1.9.10.13
This MIB module is a cisco extension to VPL/VCL table defined in rfc1695 for ATM switch connection management.
MODULE-IDENTITY

ciscoAtmConnMIBObjects		1.3.6.1.4.1.9.10.13.1
OBJECT IDENTIFIER

ciscoAtmVpl		1.3.6.1.4.1.9.10.13.1.1
OBJECT IDENTIFIER

ciscoAtmVplTable		1.3.6.1.4.1.9.10.13.1.1.1
The Virtual Path Link extension Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CiscoAtmVplEntry

ciscoAtmVplEntry		1.3.6.1.4.1.9.10.13.1.1.1.1
An entry in the Vpl table.This entry is used to model a bi-directional Vpl. This table augments the atmVplTable defined in RFC 1695. However it uses ifIndex and atmVplVpi as an Index for historical reasons. The entries are created/deleted as a by-product of creating and deleting entries in the atmVplTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	CiscoAtmVplEntry

ciscoAtmVplCastType		1.3.6.1.4.1.9.10.13.1.1.1.1.1
Vpl type is either a point to point connection or point to multipoint root or leaf.
Status: current	Access: read-write
OBJECT-TYPE
	CastType

ciscoAtmVplSpanType		1.3.6.1.4.1.9.10.13.1.1.1.1.2
Vpl span is either a transit one or a terminating one.
Status: current	Access: read-only
OBJECT-TYPE
	SpanType

ciscoAtmVplConfigType		1.3.6.1.4.1.9.10.13.1.1.1.1.3
Vpl type is either a PVC, SVC, Soft PVC or Soft Passive half leg. The half leg can be set to Passive through user configuration only.
Status: current	Access: read-write
OBJECT-TYPE
	ConfigType

ciscoAtmVplRxUpcMode		1.3.6.1.4.1.9.10.13.1.1.1.1.4
Usage Parameter Control opeartion is pass,tag,drop or local shaping at this connection.
Status: current	Access: read-write
OBJECT-TYPE
	UpcStatus

ciscoAtmVplConnState		1.3.6.1.4.1.9.10.13.1.1.1.1.5
The connection state of this VPL.
Status: current	Access: read-write
OBJECT-TYPE
	ConnState

ciscoAtmVplOamLoopbkTxInterval		1.3.6.1.4.1.9.10.13.1.1.1.1.6
Frequency of OAM loopback cells generated.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	5..60

ciscoAtmVplOamSegmentLoopback		1.3.6.1.4.1.9.10.13.1.1.1.1.7
Enable segment loopback on this virtual path.
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatus

ciscoAtmVplOamEndLoopback		1.3.6.1.4.1.9.10.13.1.1.1.1.8
Enable end to end loopback on this virtual path.
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatus

ciscoAtmVplOamAisEnable		1.3.6.1.4.1.9.10.13.1.1.1.1.9
Enable Alarm Indication Signal OAM cell generation if the interafce goes down on a crossconnect virtual path.
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatus

ciscoAtmVplOamRdiEnable		1.3.6.1.4.1.9.10.13.1.1.1.1.10
Enable Remote Defect Indication OAM cell generation if an Alarm Indication Signal OAM cell is received.
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatus

ciscoAtmVplInstallTime		1.3.6.1.4.1.9.10.13.1.1.1.1.11
The time stamp derived from sysUpTime when this VPL gets created. The VPL entries are created/deleted as a by-product of creating and deleting entries in the atmVplTable defined in RFC1695.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

ciscoAtmVplInCells		1.3.6.1.4.1.9.10.13.1.1.1.1.12
The total number of cells received on this VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplOutCells		1.3.6.1.4.1.9.10.13.1.1.1.1.13
The total number of cells transmitted on this VPL.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplCrossIfIndex		1.3.6.1.4.1.9.10.13.1.1.1.1.14
For point to point, this is the cross-connected VPL's ifIndex of this VPL. For point to multi-point connection, this will be the root VPL's ifIndex for a leaf VPL entry in the multicast chain, or it's the 1st leaf for a root VPL entry. If it's zero, it means it's not cross-connected yet. Atomically set ciscoAtmVplConnState, ciscoAtmVplCrossIfIndex and ciscoAtmVplCrossVpi will create or delete a cross connection to crossed half leg of this ciscoAtmVplCrossIfindex and ciscoAtmVplCrossVpi for p2p PVP, or add or drop a multicast connection of this ciscoAtmVplCrossIfindex and ciscoAtmVplCrossVpi to/from the root on the multicast chain for p2mp PVP.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

ciscoAtmVplCrossVpi		1.3.6.1.4.1.9.10.13.1.1.1.1.15
This specifies the VPI value of the VPL to which this VPL is cross-connected. For point to multi-point connection, this is the root VPL's VPI for the leaf entry. Similarly it is the 1st leaf's VPI value for the root entry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..4095

ciscoAtmVplNextLeafIfIndex		1.3.6.1.4.1.9.10.13.1.1.1.1.16
For point to point, this is zero i.e. not used. For point to multi-point connection, this will be the next leaf VPL's ifIndex on the multicast chain. This will be 0 if this is the root VPL entry. If it's zero for a leaf VPL, it means this is the last leaf.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

ciscoAtmVplNextLeafVpi		1.3.6.1.4.1.9.10.13.1.1.1.1.17
For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VPL's VPI on the multicast chain.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4095

ciscoAtmVplRemoteAddr		1.3.6.1.4.1.9.10.13.1.1.1.1.18
Soft PVP target address if this is the calling side Soft PVP source address if this is called side. Atomically set ConnState, RemoteAddr and RemoteVpi will create or delete a soft PVP. Atomically set ConnState, RemoteAddr without RemoteVpi will also create or delete a soft PVP but let target switch assign the vpi.
Status: current	Access: read-write
OBJECT-TYPE
	NsapAtmAddr

ciscoAtmVplRemoteVpi		1.3.6.1.4.1.9.10.13.1.1.1.1.19
Soft PVP target VPI in calling side. 0 in called side.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..4095

ciscoAtmVplLocation		1.3.6.1.4.1.9.10.13.1.1.1.1.20
Indicate calling or called side of a soft PVP. If ciscoAtmVplConfigType is not soft then ciscoAtmVplLocation value should be ignored.
Status: current	Access: read-only
OBJECT-TYPE
	Location

ciscoAtmVplSlowRetryIntv		1.3.6.1.4.1.9.10.13.1.1.1.1.21
Soft PVP slow retry interval time in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ciscoAtmVplNumAttempts		1.3.6.1.4.1.9.10.13.1.1.1.1.22
Number of retries made to install this soft PVP connection. If ciscoAtmVplConfigType is not soft then ciscoAtmVplNumAttempts value should be ignored.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplLastReleaseCause		1.3.6.1.4.1.9.10.13.1.1.1.1.23
Value of the Cause field of the Cause Information Element in the last Release Signalling message received for this SPVP. Indicates the reason for the Release. ciscoAtmVplConfigType is not soft then ciscoAtmVplLastReleaseCause value should be ignored.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..127

ciscoAtmVplLogicalPortDef		1.3.6.1.4.1.9.10.13.1.1.1.1.24
Indicates whether the VPC at this VPL interface is an Atm Logical Port interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	notLogicalIf(1), isLogicalIf(2)

ciscoAtmVplLogicalPortIndex		1.3.6.1.4.1.9.10.13.1.1.1.1.25
The ifTable index of the Atm logical port interface associated with this VPL. Only valid if the value of atmVplLogicalPortDef is isLogicalIf, and the VPL row is active.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

ciscoAtmVplUpcViolations		1.3.6.1.4.1.9.10.13.1.1.1.1.26
The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this VPL. On LS1010 systems, this counter is valid only if equipped with the Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplEpdTpdCellDrops		1.3.6.1.4.1.9.10.13.1.1.1.1.27
Never implemented.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplEpdTpdPacketDrops		1.3.6.1.4.1.9.10.13.1.1.1.1.28
Never implemented.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplEpdTpdPacketsIn		1.3.6.1.4.1.9.10.13.1.1.1.1.29
Never implemented.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplClp1Drops		1.3.6.1.4.1.9.10.13.1.1.1.1.30
Never implemented.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplDefaultRxUpcTolerance		1.3.6.1.4.1.9.10.13.1.1.1.1.31
If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum Burst Size for VBR connectons) requested for Usage Parameter Control is not explicitly specified in VPL creation, this object contains the default that is used. If tolerance is explicitly specified in VPL creation, it can be found in the Traffic Table row specified by atmVplReceiveTrafficDescrIndex, and the value of this object is -1.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ciscoAtmVplDefaultRxUpcVbrCdvt		1.3.6.1.4.1.9.10.13.1.1.1.1.32
If the Cell Delay Variation Tolerance (CDVT) requested for Usage Parameter Control for a VBR connection is not explicitly specified in VPL creation, this object contains the default that is used. If CDVT is explicitly specified in VPL creation, it can be found in the Traffic Table row specified by atmVplReceiveTrafficDescrIndex, and the value of this object is -1.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ciscoAtmVplLsPerVcqWrrWeight		1.3.6.1.4.1.9.10.13.1.1.1.1.33
Configure the weighting specified for a VP half-leg within a service class to make the scheduling decision among other active VPLs in the service class. This is for transmit on the VPL on the interface. This parameter only applies to transit VPs. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..15

ciscoAtmVplLsPerVcqTunnelIsShaped		1.3.6.1.4.1.9.10.13.1.1.1.1.34
Determines whether this is to be a -shaped- VP, per the Lightstream per-VC queueing chipset. If the value specified is TRUE, the VP is to be a shaped VP Tunnel. Such a VP cannot be cross-connected. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

ciscoAtmVplLsPerVcqXmtQueuedCells		1.3.6.1.4.1.9.10.13.1.1.1.1.35
Number of cells received on this VPL and residing on the per-connection queue. Note that this value is not valid until the VPL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ciscoAtmVplLsPerVcQThreshGrp		1.3.6.1.4.1.9.10.13.1.1.1.1.36
The Threshold Group to which the cell-queue for cells received by this VP are queued. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
Status: current	Access: read-only
OBJECT-TYPE
	LsPerVcqThresholdGroup

ciscoAtmVplInClp0Cells		1.3.6.1.4.1.9.10.13.1.1.1.1.37
The total number of cells with the CLP bit clear received on this VPL. Note that these cells may subsequently be discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplInClp1Cells		1.3.6.1.4.1.9.10.13.1.1.1.1.38
The total number of cells with the CLP bit set received on this VPL. Note that these cells may subsequently be discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplOutClp0Cells		1.3.6.1.4.1.9.10.13.1.1.1.1.39
The total number of cells with the CLP bit clear transmitted on this VPL. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplOutClp1Cells		1.3.6.1.4.1.9.10.13.1.1.1.1.40
The total number of cells with the CLP bit set transmitted on this VPL. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplCellDrops		1.3.6.1.4.1.9.10.13.1.1.1.1.41
The total number of cells received on this VPL, but discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplClp0VcqFullCellDrops		1.3.6.1.4.1.9.10.13.1.1.1.1.43
The total number of cells received on this VPL with the CLP bit clear, discarded because the per-VC queue limit is exceeded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplVcqClpThreshCellDrops		1.3.6.1.4.1.9.10.13.1.1.1.1.44
The total number of cells received on this VPL, discarded because the discard threshold (as opposed to the queue-limit) is exceeded on the per-VC queue, and the CLP bit is set. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplLsPerVcqTunnelIsHierarchical		1.3.6.1.4.1.9.10.13.1.1.1.1.45
Determines whether this is to be a -Hierarchical- VP, per the Lightstream per-VC queueing chipset. If the value specified is TRUE, the VP is to be a Hierarchical VP Tunnel. Such a VP cannot be cross-connected. This object is defined on a LS1010 only when the switch is equipped with the Lightstream per-VC queueing chipset.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

ciscoAtmVplRxNegTraffDescrIndex		1.3.6.1.4.1.9.10.13.1.1.1.1.46
Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the receive direction of this VPL. This object is not instantiated if this VPL is not the calling side of a soft VP, or if there was no traffic negotiation.
Status: current	Access: read-only
OBJECT-TYPE
	AtmTrafficDescrParamIndex

ciscoAtmVplTxNegTraffDescrIndex		1.3.6.1.4.1.9.10.13.1.1.1.1.47
Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the transmit direction of this VPL. This object is not instantiated if this VPL is not the calling side of a soft VP, or if there was no traffic negotiation.
Status: current	Access: read-only
OBJECT-TYPE
	AtmTrafficDescrParamIndex

ciscoAtmVplSwFabOutCells		1.3.6.1.4.1.9.10.13.1.1.1.1.48
The total number of cells transmitted on this VPL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplSwFabOutClp0Cells		1.3.6.1.4.1.9.10.13.1.1.1.1.49
The total number of cells with the CLP bit clear transmitted on this VPL by the Switch Fabric. This object is not instantiated for a VPL that is a logical interface (VP Tunnel). This object is not instantiated on systems that do not have support for collecting such statistics.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplSwFabOutClp1Cells		1.3.6.1.4.1.9.10.13.1.1.1.1.50
The total number of cells with the CLP bit set transmitted on this VPL by the Switch Fabric. This object is not instantiated for a VPL that is a logical interface (VP Tunnel). This object is not instantiated on systems that do not have support for collecting such statistics.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVplConnName		1.3.6.1.4.1.9.10.13.1.1.1.1.51
A human readable string that identifies this connection. This object will return a zero-length string if value is not set.
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString

ciscoAtmVplConnType		1.3.6.1.4.1.9.10.13.1.1.1.1.52
This object represent the PVP Type for this connection. - local connection within the node - endToEnd across several nodes This object serves as an information object for a management system and has no functional meaning to the switch.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	local(1), endToEnd(2)

ciscoAtmVcl		1.3.6.1.4.1.9.10.13.1.2
OBJECT IDENTIFIER

ciscoAtmVclTable		1.3.6.1.4.1.9.10.13.1.2.1
The Virtual Channel Link extension Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CiscoAtmVclEntry

ciscoAtmVclEntry		1.3.6.1.4.1.9.10.13.1.2.1.1
An entry in the Vcl table.This entry is used to model a bi-directional Vcl. This table augments the atmVclTable defined in RFC 1695. However it uses ifIndex, atmVclVpi and atmVclVci as an Index for historical reasons. The entries are created/deleted as a by-product of creating and deleting entries in the atmVclTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	CiscoAtmVclEntry

ciscoAtmVclCastType		1.3.6.1.4.1.9.10.13.1.2.1.1.1
Vcl type is either a point to point connection or point to multipoint root or leaf.
Status: current	Access: read-write
OBJECT-TYPE
	CastType

ciscoAtmVclSpanType		1.3.6.1.4.1.9.10.13.1.2.1.1.2
Vcl span is either a transit one or a terminating one.
Status: current	Access: read-only
OBJECT-TYPE
	SpanType

ciscoAtmVclConfigType		1.3.6.1.4.1.9.10.13.1.2.1.1.3
Vcl type is either a PVC, SVC, Soft PVC or Soft Passive half leg. The half leg can be set to Passive through user configuration only.
Status: current	Access: read-write
OBJECT-TYPE
	ConfigType

ciscoAtmVclRxUpcMode		1.3.6.1.4.1.9.10.13.1.2.1.1.4
Usage Parameter Control opeartion is pass,tag,drop or local shaping at this connection.
Status: current	Access: read-write
OBJECT-TYPE
	UpcStatus

ciscoAtmVclEpdEnable		1.3.6.1.4.1.9.10.13.1.2.1.1.5
Early Packet Discard option used for this VCL. The use is as follows: enable(1) Packet-discard is enabled. disable(2) Packet-discard is disabled. useTrafficDescr(3) Packet-discard in the receive direction is as specified by the atmTrafficFrameDiscard value in row corresponding to atmVclReceiveTrafficDescrIndex. For VCLs of type spvcInitiator, the packet-discard in the reverse direction is as specified by the atmTrafficFrameDiscard value in row corresponding to atmVclTransmitTrafficDescrIndex.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2), useTrafficDescr(3)

ciscoAtmVclConnState		1.3.6.1.4.1.9.10.13.1.2.1.1.6
The connection state of this VCL.
Status: current	Access: read-write
OBJECT-TYPE
	ConnState

ciscoAtmVclOamLoopbkTxInterval		1.3.6.1.4.1.9.10.13.1.2.1.1.7
Frequency of OAM loopback cell are generated on this virtual channel.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	5..60

ciscoAtmVclOamSegmentLoopback		1.3.6.1.4.1.9.10.13.1.2.1.1.8
Enable segment loopback on this virtual channel.
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatus

ciscoAtmVclOamEndLoopback		1.3.6.1.4.1.9.10.13.1.2.1.1.9
Enable end to end loopback on this virtual channel.
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatus

ciscoAtmVclOamAisEnable		1.3.6.1.4.1.9.10.13.1.2.1.1.10
Enable Alarm Indication Signal OAM cell generation if the interafce goes down on a crossconnect virtual channel.
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatus

ciscoAtmVclOamRdiEnable		1.3.6.1.4.1.9.10.13.1.2.1.1.11
Enable Remote Defect Indication OAM cell generation if an Alarm Indication Signal OAM cell is received.
Status: current	Access: read-write
OBJECT-TYPE
	EnableStatus

ciscoAtmVclInstallTime		1.3.6.1.4.1.9.10.13.1.2.1.1.12
The time stamp derived from sysUpTime when this VCL gets created. The VCL entries are created/deleted as a by-product of creating and deleting entries in the atmVclTable defined in RFC1695.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

ciscoAtmVclInCells		1.3.6.1.4.1.9.10.13.1.2.1.1.13
The total number of cells received on this VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclOutCells		1.3.6.1.4.1.9.10.13.1.2.1.1.14
The total number of cells transmitted on this VCL.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclCrossIfIndex		1.3.6.1.4.1.9.10.13.1.2.1.1.15
For point to point, this is the cross-connected VCL's ifIndex of this VCL. For point to multi-point connection, this will be the root VCL's ifIndex for a leaf VCL entry in the multicast chain, or it's the 1st leaf VCL for a root VCL entry. If it's zero, it means it's not cross-connected yet. Atomically set ciscoAtmVclConnState, ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and ciscoAtmVclCrossVci will create or delete a cross connection to crossed half leg of this ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and ciscoAtmVclCrossVci for p2p PVC, or add or drop a multicast connection to/from the root of this ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and ciscoAtmVclCrossVci on the multicast chain for p2mp PVC.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

ciscoAtmVclCrossVpi		1.3.6.1.4.1.9.10.13.1.2.1.1.16
This specifies the VPI value of the VCL to which this VCL is cross-connected. For point to multi-point connection, this is the root VCL's VPI for the leaf entry. Similarly it is the 1st leaf's VPI value for the root entry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..4095

ciscoAtmVclCrossVci		1.3.6.1.4.1.9.10.13.1.2.1.1.17
This specifies the VCI value of the VCL to which this VCL is cross-connected. For point to multi-point connection, this is the root VCL's VCI for the leaf entry. Similarly it is the 1st leaf's VCI value for the root entry.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ciscoAtmVclNextLeafIfIndex		1.3.6.1.4.1.9.10.13.1.2.1.1.18
For point to point, this is zero i.e. not used. For point to multi-point connection, this will be the next leaf VCL's ifIndex on the multicast chain. This will be 0 if this is the root VCL entry. If it's zero for a leaf VCL, it means this is the last leaf.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

ciscoAtmVclNextLeafVpi		1.3.6.1.4.1.9.10.13.1.2.1.1.19
For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VCL's VPI on the multicast chain.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4095

ciscoAtmVclNextLeafVci		1.3.6.1.4.1.9.10.13.1.2.1.1.20
For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VCL's VCI on the multicast chain.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

ciscoAtmVclAalEncapFlag		1.3.6.1.4.1.9.10.13.1.2.1.1.21
Encapsulation type for terminating VC.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), aal5Snap(2), aal5Nlpid(3), aal5FrNlpid(4), aal5Mux(5), aal34Smds(6), aalQsAal(7), aal5Ilmi(8), aal5Lane(9), aal5Pnni(10)

ciscoAtmVclAalEncapProtocol		1.3.6.1.4.1.9.10.13.1.2.1.1.22
Protocol for terminating VC if EncapFlag is aal5Mux.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), ip(2), xns(3), appletalk(4), clns(5), decnet(6), novell(7), apollo(8), vines(9)

ciscoAtmVclAalUserVcType		1.3.6.1.4.1.9.10.13.1.2.1.1.23
Following is the list of user virtual circuit types in case aal5Lane encapusation on this virtual channel. boxConfigure -- The shared Server/Client end of a Configure VCC busForward -- The BUS end of the Data Forward VCC busSend -- The BUS end of the Data Send VCC clientConfigure -- The LE Client end of the Configure Direct VCC clientData -- One end of the Data Direct VCC clientDirect -- The LE Client end of the Control Direct VCC clientDistribute -- The LE Client end of the Control Distribute VCC clientForward -- The LE Client end of the Multicast Forward VCC clientSend -- The LE Client end of the Multicast Send VCC configure -- The Config Server end of any Configure VCC serverConfigure -- The LE Server end of the Configure VCC serverDirect -- The LE Server end of the Control Direct VCC.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), boxConfigure(2), busForward(3), busSend(4), clientConfigure(5), clientData(6), clientDirect(7), clientDistribute(8), clientForward(9), clientSend(10), configure(11), serverConfigure(12), serverDirect(13), serverDistribute(14)

ciscoAtmVclAtmInArpInterval		1.3.6.1.4.1.9.10.13.1.2.1.1.24
Time interval in minutes to send InArp on a PVC for IP over ATM. 0 will disable the InArp for this pvc.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..60

ciscoAtmVclRemoteAddr		1.3.6.1.4.1.9.10.13.1.2.1.1.25
Soft PVC target address if this is the calling side Soft PVC source address if this is called side. Atomically set ConnState, RemoteAddr, RemoteVpi and RemoteVci will create or delete a soft PVC. Atomically set ConnState, RemoteAddr without RemoteVpi, Remote Vci will also create or delete a soft PVC but let target switch assign the vpi and vci.
Status: current	Access: read-write
OBJECT-TYPE
	NsapAtmAddr

ciscoAtmVclRemoteVpi		1.3.6.1.4.1.9.10.13.1.2.1.1.26
Soft PVC target VPI in calling side. 0 in called side.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..4095

ciscoAtmVclRemoteVci		1.3.6.1.4.1.9.10.13.1.2.1.1.27
Soft PVC target VCI in calling side. 0 in called side.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ciscoAtmVclLocation		1.3.6.1.4.1.9.10.13.1.2.1.1.28
Indicate calling or called side of a soft PVC. If ciscoAtmVclConfigType is not soft then ciscoAtmVclLocation value should be ignored.
Status: current	Access: read-only
OBJECT-TYPE
	Location

ciscoAtmVclSlowRetryIntv		1.3.6.1.4.1.9.10.13.1.2.1.1.29
Soft PVC slow retry interval in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

ciscoAtmVclNumAttempts		1.3.6.1.4.1.9.10.13.1.2.1.1.30
Number of retries made to install this soft PVC connection. If ciscoAtmVclConfigType is not soft then ciscoAtmVclNumAttempts value should be ignored.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclLastReleaseCause		1.3.6.1.4.1.9.10.13.1.2.1.1.31
Value of the Cause field of the Cause Information Element in the last Release Signalling message received for this SPVC. Indicates the reason for the Release. ciscoAtmVclConfigType is not soft then ciscoAtmVclLastReleaseCause value should be ignored.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..127

ciscoAtmVclUpcViolations		1.3.6.1.4.1.9.10.13.1.2.1.1.32
The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this VCL. On LS1010 systems, this counter is valid only on those equipped with the Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclEpdTpdCellDrops		1.3.6.1.4.1.9.10.13.1.2.1.1.33
Never implemented.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclEpdTpdPacketDrops		1.3.6.1.4.1.9.10.13.1.2.1.1.34
The total number of EPD/TPD packet drops of packets received on this VCL. This counter is valid only: - if EPD is enabled on this VCL. - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclEpdTpdPacketsIn		1.3.6.1.4.1.9.10.13.1.2.1.1.35
The total number of packets received in their entirety on this VPL. This counter is valid only: - if EPD is enabled on this VCL. - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclClp1Drops		1.3.6.1.4.1.9.10.13.1.2.1.1.37
Never implemented.
Status: obsolete	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclDefaultRxUpcTolerance		1.3.6.1.4.1.9.10.13.1.2.1.1.38
If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum Burst Size for VBR connectons) requested for Usage Parameter Control is not explicitly specified in VCL creation, this object contains the default that is used.If tolerance is explicitly specified in VCL creation, it can be found in the Traffic Table row specified by atmVclReceiveTrafficDescrIndex, and the value of this object is -1.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ciscoAtmVclDefaultRxUpcVbrCdvt		1.3.6.1.4.1.9.10.13.1.2.1.1.39
If the Cell Delay Variation Tolerance (CDVT) requested for Usage Parameter Control for a VBR connection is not explicitly specified in VCL creation, this object contains the default that is used. If CDVT is explicitly specified in VCL creation, it can be found in the Traffic Table row specified by atmVclReceiveTrafficDescrIndex, and the value of this object is -1.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ciscoAtmVclLsPerVcqWrrWeight		1.3.6.1.4.1.9.10.13.1.2.1.1.40
Configure the weighting specified for a VC half-leg within a service class to make the scheduling decision among other active VCLs in the service class. This is for transmit on the VCL on the interface. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..15

ciscoAtmVclLsPerVcqXmtQueuedCells		1.3.6.1.4.1.9.10.13.1.2.1.1.41
Number of cells received on this VCL and residing on the per-connection queue. Note that this value is not valid until the VCL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

ciscoAtmVclLsPerVcQThreshGrp		1.3.6.1.4.1.9.10.13.1.2.1.1.42
The Threshold Group to which the cell-queue for cells received by this VC are queued. Note that this value is not valid until the VCL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
Status: current	Access: read-only
OBJECT-TYPE
	LsPerVcqThresholdGroup

ciscoAtmVclInClp0Cells		1.3.6.1.4.1.9.10.13.1.2.1.1.43
The total number of cells with the CLP bit clear received on this VCL. Note that these cells may subsequently be discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclInClp1Cells		1.3.6.1.4.1.9.10.13.1.2.1.1.44
The total number of cells with the CLP bit set received on this VCL. Note that these cells may subsequently be discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclOutClp0Cells		1.3.6.1.4.1.9.10.13.1.2.1.1.45
The total number of cells with the CLP bit clear transmitted on this VCL. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclOutClp1Cells		1.3.6.1.4.1.9.10.13.1.2.1.1.46
The total number of cells with the CLP bit set transmitted on this VCL. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclCellDrops		1.3.6.1.4.1.9.10.13.1.2.1.1.47
The total number of cells received on this VCL, but discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclClp0VcqFullCellDrops		1.3.6.1.4.1.9.10.13.1.2.1.1.48
The total number of cells received on this VCL with the CLP bit clear, discarded because the per-VC queue limit is exceeded. This counter is valid only: - if EPD is disabled on the VCL. - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclVcqClpThreshCellDrops		1.3.6.1.4.1.9.10.13.1.2.1.1.49
The total number of cells received on this VCL, discarded because the discard threshold (as opposed to the queue-limit) is exceeded on the per-VC queue, and the CLP bit is set. This counter is valid only: - if EPD is disabled on the VCL. - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclRxNegTraffDescrIndex		1.3.6.1.4.1.9.10.13.1.2.1.1.50
Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the receive direction of this VCL. This object is not instantiated if this VCL is not the calling side of a soft VC, or if there was no traffic negotiation.
Status: current	Access: read-only
OBJECT-TYPE
	AtmTrafficDescrParamIndex

ciscoAtmVclTxNegTraffDescrIndex		1.3.6.1.4.1.9.10.13.1.2.1.1.51
Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the transmit direction of this VCL. This object is not instantiated if this VCL is not the calling side of a soft VC, or if there was no traffic negotiation.
Status: current	Access: read-only
OBJECT-TYPE
	AtmTrafficDescrParamIndex

ciscoAtmVclSwFabOutCells		1.3.6.1.4.1.9.10.13.1.2.1.1.52
The total number of cells transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclSwFabOutClp0Cells		1.3.6.1.4.1.9.10.13.1.2.1.1.53
The total number of cells with the CLP bit clear transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclSwFabOutClp1Cells		1.3.6.1.4.1.9.10.13.1.2.1.1.54
The total number of cells with the CLP bit set transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

ciscoAtmVclConnName		1.3.6.1.4.1.9.10.13.1.2.1.1.55
A human readable string that identifies this connection. This object will return a zero-length string if value is not set.
Status: current	Access: read-write
OBJECT-TYPE
	SnmpAdminString

ciscoAtmVclConnType		1.3.6.1.4.1.9.10.13.1.2.1.1.56
This object represent the PVC Type for this connection. - local connection within the node - endToEnd across several nodes. This object serves as an information object for a management system and has no functional meaning to the switch.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	local(1), endToEnd(2)

ciscoAtmSvp		1.3.6.1.4.1.9.10.13.1.3
OBJECT IDENTIFIER

ciscoAtmSvpAddrTable		1.3.6.1.4.1.9.10.13.1.3.1
Switched virtual path link address table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CiscoAtmSvpAddrEntry

ciscoAtmSvpAddrEntry		1.3.6.1.4.1.9.10.13.1.3.1.1
An entry in the Switched Vrtual Path address table.
Status: current	Access: not-accessible
OBJECT-TYPE
	CiscoAtmSvpAddrEntry

ciscoAtmSvpAddr		1.3.6.1.4.1.9.10.13.1.3.1.1.1
It depends on the direction.This could be p2pCallingSide address on a called side VPL, or p2pCalledSide address on a calling side VPL or p2mpRoot address on a p2mp leaf side VPL or p2mpLeaf address on a p2mp root side VPL.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(20)

ciscoAtmSvpVpi		1.3.6.1.4.1.9.10.13.1.3.1.1.2
This SVP's VPI value on this interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..4095

ciscoAtmSvpDirection		1.3.6.1.4.1.9.10.13.1.3.1.1.3
Indicate whether this VPL is calling side, called side, root or leaf for this address.
Status: current	Access: read-only
OBJECT-TYPE
	Direction

ciscoAtmSvc		1.3.6.1.4.1.9.10.13.1.4
OBJECT IDENTIFIER

ciscoAtmSvcAddrTable		1.3.6.1.4.1.9.10.13.1.4.1
Switched virtual channel link address table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CiscoAtmSvcAddrEntry

ciscoAtmSvcAddrEntry		1.3.6.1.4.1.9.10.13.1.4.1.1
An entry in the SVC address table.
Status: current	Access: not-accessible
OBJECT-TYPE
	CiscoAtmSvcAddrEntry

ciscoAtmSvcAddr		1.3.6.1.4.1.9.10.13.1.4.1.1.1
It depends on the direction.This could be p2pCallingSide address on a called side VCL, or p2pCalledSide address on a calling side VCL or p2mpRoot address on a p2mp leaf side VCL or p2mpLeaf address on a p2mp root side VCL.
Status: current	Access: not-accessible
OBJECT-TYPE
	OCTET STRING	Size(20)

ciscoAtmSvcVpi		1.3.6.1.4.1.9.10.13.1.4.1.1.2
This SVC's VPI value on this interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..4095

ciscoAtmSvcVci		1.3.6.1.4.1.9.10.13.1.4.1.1.3
This SVC's VCI value on this interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..65535

ciscoAtmSvcDirection		1.3.6.1.4.1.9.10.13.1.4.1.1.4
Indicate whether this VCL is calling side, called side, root or leaf for this address.
Status: current	Access: read-only
OBJECT-TYPE
	Direction

ciscoAtmSnoopVc		1.3.6.1.4.1.9.10.13.1.5
OBJECT IDENTIFIER

ciscoAtmSnoopVcTable		1.3.6.1.4.1.9.10.13.1.5.1
Snooping VC Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CiscoAtmSnoopVcEntry

ciscoAtmSnoopVcEntry		1.3.6.1.4.1.9.10.13.1.5.1.1
An entry in the Snoop VC table. This entry models a VC snooping connection. The ifIndex indicates the snooping interface, the atmVclVpi and atmVclVci specifies the VPI and VCI value of the snooping connection. To create or destroy a snooping connection at an ATM interface, the following procedures are used: Configure VC Snooping A snooping connection is configured in one step by a set-request with all necessary snoop parameter values and set-request to the object ciscoAtmSnoopVcRowStatus to createAndGo(4). This may fail for the following reasons: - The selected snooping VPI/VCI values are unavailable, - The selected snooping VPI/VCI values are in use. - The selected snooping interface is CPU interface. - The selected snooped connection doesn't exist. - There is no traffic in the selected snoop direction. - Resource failure during configuration of snooping connection. De-Configure VC Snooping A snooping connection is deconfigured by a set-request to the object ciscoAtmSnoopVcRowStatus to destroy(6), and the agent releases all associated resources.
Status: current	Access: not-accessible
OBJECT-TYPE
	CiscoAtmSnoopVcEntry

ciscoAtmSnoopVcSnoopedIfIndex		1.3.6.1.4.1.9.10.13.1.5.1.1.1
This specifies the ifIndex of the snooped interface.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

ciscoAtmSnoopVcSnoopedVpi		1.3.6.1.4.1.9.10.13.1.5.1.1.2
This specifies the VPI value of the snooped connection endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4095

ciscoAtmSnoopVcSnoopedVci		1.3.6.1.4.1.9.10.13.1.5.1.1.3
This specifies the VCI value of the snooped connection endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..65535

ciscoAtmSnoopVcDir		1.3.6.1.4.1.9.10.13.1.5.1.1.4
This specifies the traffic direction at the snooped connection endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	SnoopDirType

ciscoAtmSnoopVcState		1.3.6.1.4.1.9.10.13.1.5.1.1.5
The connection state of this Snooping connetion.
Status: current	Access: read-only
OBJECT-TYPE
	ConnState

ciscoAtmSnoopVcRowStatus		1.3.6.1.4.1.9.10.13.1.5.1.1.6
This object is used to create a new row or delete an existing row in this table. This gives the way to configure one-shot per-vc snooping connection
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

ciscoAtmSnoopVp		1.3.6.1.4.1.9.10.13.1.6
OBJECT IDENTIFIER

ciscoAtmSnoopVpTable		1.3.6.1.4.1.9.10.13.1.6.1
Snooping VP Table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CiscoAtmSnoopVpEntry

ciscoAtmSnoopVpEntry		1.3.6.1.4.1.9.10.13.1.6.1.1
An entry in the Snoop VP table. This entry models a VP snooping connection. The ifIndex indicates the snooping interface, the atmVclVpi specifies the VPI value of the snooping connection. To create or destroy a snooping connection at an ATM interface, the following procedures are used: Configure VP Snooping A snooping connection is configured in one step by a set-request with all necessary snoop parameter values and set-request to the object ciscoAtmSnoopVpRowStatus to createAndGo(4). This may fail for the following reasons: - The selected snooping VPI values are unavailable, - The selected snooping VPI values are in use. - The selected snooping interface is CPU interface. - The selected snooped connection doesn't exist. - There is no traffic in the selected snoop direction. - Resource failure during configuration of snooping connection. De-Configure VP Snooping A snooping connection is deconfigured by a set-request to the object ciscoAtmSnoopVpRowStatus to destroy(6), and the agent releases all associated resources.
Status: current	Access: not-accessible
OBJECT-TYPE
	CiscoAtmSnoopVpEntry

ciscoAtmSnoopVpSnoopedIfIndex		1.3.6.1.4.1.9.10.13.1.6.1.1.1
This specifies the ifIndex of the snooped interface.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

ciscoAtmSnoopVpSnoopedVpi		1.3.6.1.4.1.9.10.13.1.6.1.1.2
This specifies the VPI value of the snooped connection endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4095

ciscoAtmSnoopVpDir		1.3.6.1.4.1.9.10.13.1.6.1.1.3
This specifies the traffic direction at the snooped connection endpoint.
Status: current	Access: read-create
OBJECT-TYPE
	SnoopDirType

ciscoAtmSnoopVpState		1.3.6.1.4.1.9.10.13.1.6.1.1.4
The connection state of this Snooping connection .
Status: current	Access: read-only
OBJECT-TYPE
	ConnState

ciscoAtmSnoopVpRowStatus		1.3.6.1.4.1.9.10.13.1.6.1.1.5
This object is used to create a new row or delete an existing row in this table. This gives the way to configure one-shot per-vp snooping connection
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

ciscoAtmSvcFrameDiscardUsesAal5Ie		1.3.6.1.4.1.9.10.13.1.4.2
Determines mechanism to use on interfaces to specify frame discard. Specifying a value of true causes the presence of the AAL5 IE to influence whether frame discard is used on an SVC. If AAL5 IE is present in a received SETUP, frame discard is used. Specifying a value of false results in no influence on presence of the frame discard by the AAL5 IE.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

ciscoAtmConnMIBConformance		1.3.6.1.4.1.9.10.13.3
OBJECT IDENTIFIER

ciscoAtmConnMIBCompliances		1.3.6.1.4.1.9.10.13.3.1
OBJECT IDENTIFIER

ciscoAtmConnMIBGroups		1.3.6.1.4.1.9.10.13.3.2
OBJECT IDENTIFIER

ciscoAtmConnMIBCompliance		1.3.6.1.4.1.9.10.13.3.1.1
The compliance statement for the Cisco ATM connection management group.
Status: obsolete	Access: read-write
MODULE-COMPLIANCE

ciscoAtmConnMIBCompliance2		1.3.6.1.4.1.9.10.13.3.1.2
The compliance statement for the Cisco ATM connection management group.
Status: obsolete	Access: read-write
MODULE-COMPLIANCE

ciscoAtmConnMIBCompliance3		1.3.6.1.4.1.9.10.13.3.1.3
The compliance statement for the Cisco ATM connection management group.
Status: obsolete	Access: read-write
MODULE-COMPLIANCE

ciscoAtmConnMIBCompliance4		1.3.6.1.4.1.9.10.13.3.1.4
The compliance statement for the Cisco ATM connection management group.
Status: obsolete	Access: read-write
MODULE-COMPLIANCE

ciscoAtmConnMIBCompliance5		1.3.6.1.4.1.9.10.13.3.1.5
The compliance statement for the Cisco ATM connection management group.
Status: deprecated	Access: read-write
MODULE-COMPLIANCE

ciscoAtmConnMIBCompliance6		1.3.6.1.4.1.9.10.13.3.1.6
The compliance statement for the Cisco ATM connection management group.
Status: deprecated	Access: read-write
MODULE-COMPLIANCE

ciscoAtmConnMIBCompliance7		1.3.6.1.4.1.9.10.13.3.1.7
The compliance statement for the Cisco ATM connection management group.
Status: deprecated	Access: read-write
MODULE-COMPLIANCE

ciscoAtmConnMIBCompliance8		1.3.6.1.4.1.9.10.13.3.1.8
The compliance statement for the Cisco ATM connection management group.
Status: current	Access: read-write
MODULE-COMPLIANCE

ciscoAtmConnMIBGroup		1.3.6.1.4.1.9.10.13.3.2.1
Tok_String
Status: deprecated	Access: read-write
OBJECT-GROUP

ciscoAtmConnMIBGroup2		1.3.6.1.4.1.9.10.13.3.2.2
Tok_String
Status: obsolete	Access: read-write
OBJECT-GROUP

ciscoAtmConnMIBGroup3		1.3.6.1.4.1.9.10.13.3.2.3
Tok_String
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmConnMIBlsPerVcqGroup		1.3.6.1.4.1.9.10.13.3.2.4
A collection of objects which are supported on platforms using the Lightstream per-VC queueing chipset.
Status: obsolete	Access: read-write
OBJECT-GROUP

ciscoAtmConnMIBlsFcPfqGroup		1.3.6.1.4.1.9.10.13.3.2.5
A collection of objects which are supported on LS1010 systems equipped with the FC-PFQ feature card.
Status: deprecated	Access: read-write
OBJECT-GROUP

ciscoAtmConnMIBlsPerVcqGroup2		1.3.6.1.4.1.9.10.13.3.2.6
A collection of objects which are supported on platforms using the Lightstream per-VC queueing chipset.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmConnMIBNegTraffGroup		1.3.6.1.4.1.9.10.13.3.2.7
A collection of objects to report negotiated traffic parameters on a Cisco ATM switch.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmConnMIBlsFcPfqGroup1		1.3.6.1.4.1.9.10.13.3.2.8
A collection of objects which are supported on LS1010 systems equipped with the FC-PFQ feature card.
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmConnMIBGroup1		1.3.6.1.4.1.9.10.13.3.2.9
Tok_String
Status: deprecated	Access: read-write
OBJECT-GROUP

ciscoAtmConnMIBGroup4		1.3.6.1.4.1.9.10.13.3.2.10
Tok_String
Status: current	Access: read-write
OBJECT-GROUP

ciscoAtmConnNmsGroup		1.3.6.1.4.1.9.10.13.3.2.11
A group of objects that provides additional information for a management system
Status: current	Access: read-write
OBJECT-GROUP