CISCO-ALPS-MIB

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
IF-MIB	CISCO-SMI	RFC1382-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Counter32
Gauge32	Integer32	IpAddress
TimeTicks	NOTIFICATION-TYPE	MODULE-COMPLIANCE
OBJECT-GROUP	NOTIFICATION-GROUP	DisplayString
TEXTUAL-CONVENTION	TruthValue	RowStatus
TimeStamp	TimeInterval	ifIndex
InterfaceIndex	ciscoMgmt	X121Address

Defined Types

AlpsCktName
Specifies the ALPS Circuit Name. It is configured from the parser and is adminstratively assigned. This is globally unique.
TEXTUAL-CONVENTION
	OCTET STRING	Size(1..12)

AlpsAscuA1A2Value
Specifies A1 or A2 value of an ASCU. The A1 & A2 values together specify an ASCU within an ALPS circuit.
TEXTUAL-CONVENTION
	Integer32	0..255

AlpsRemPeerEntry
SEQUENCE
	alpsRemPeerIpAddr	IpAddress
	alpsRemPeerConnType	INTEGER
	alpsRemPeerLocalPort	Integer32
	alpsRemPeerRemotePort	Integer32
	alpsRemPeerState	INTEGER
	alpsRemPeerUptime	TimeTicks
	alpsRemPeerNumActiveCkts	Gauge32
	alpsRemPeerIdleTimer	TimeInterval
	alpsRemPeerAlarmsEnabled	TruthValue
	alpsRemPeerTCPQlen	Integer32
	alpsRemPeerOutPackets	Counter32
	alpsRemPeerOutOctets	Counter32
	alpsRemPeerInPackets	Counter32
	alpsRemPeerInOctets	Counter32
	alpsRemPeerDropsGiant	Counter32
	alpsRemPeerDropsQFull	Counter32
	alpsRemPeerDropsPeerUnreach	Counter32
	alpsRemPeerRowStatus	RowStatus

AlpsRemPeerCfgEntry
SEQUENCE
	alpsRemPeerCfgIpAddr	IpAddress
	alpsRemPeerCfgProtocol	INTEGER
	alpsRemPeerCfgActivation	INTEGER
	alpsRemPeerCfgTCPQLen	Integer32
	alpsRemPeerCfgIdleTimer	TimeInterval
	alpsRemPeerCfgNoCircTimer	TimeInterval
	alpsRemPeerCfgAlarmsOn	TruthValue
	alpsRemPeerCfgStatIntvl	TimeInterval
	alpsRemPeerCfgStatRetry	Integer32
	alpsRemPeerCfgRowStatus	RowStatus

AlpsRemPeerConnEntry
SEQUENCE
	alpsRemPeerConnIpAddr	IpAddress
	alpsRemPeerConnIdString	DisplayString
	alpsRemPeerConnLocalPort	Integer32
	alpsRemPeerConnForeignPort	Integer32
	alpsRemPeerConnState	INTEGER
	alpsRemPeerConnProtocol	INTEGER
	alpsRemPeerConnCreation	INTEGER
	alpsRemPeerConnActivation	INTEGER
	alpsRemPeerConnUptime	TimeTicks
	alpsRemPeerConnNumActCirc	Integer32
	alpsRemPeerConnLastTxRx	TimeStamp
	alpsRemPeerConnLastRxAny	TimeStamp
	alpsRemPeerConnIdleTimer	TimeInterval
	alpsRemPeerConnNoCircTimer	TimeInterval
	alpsRemPeerConnTCPQLen	Integer32
	alpsRemPeerConnAlarmsOn	TruthValue
	alpsRemPeerConnStatIntvl	Integer32
	alpsRemPeerConnStatRetry	Integer32
	alpsRemPeerConnDownReason	INTEGER
	alpsRemPeerConnOutPackets	Counter32
	alpsRemPeerConnOutOctets	Counter32
	alpsRemPeerConnInPackets	Counter32
	alpsRemPeerConnInOctets	Counter32
	alpsRemPeerConnDropsGiant	Counter32
	alpsRemPeerConnDropsQFull	Counter32
	alpsRemPeerConnDropsUnreach	Counter32
	alpsRemPeerConnDropsVersion	Counter32

AlpsCktBaseEntry
SEQUENCE
	alpsCktBaseName	AlpsCktName
	alpsCktBaseDlcType	INTEGER
	alpsCktBasePriPeerAddr	IpAddress
	alpsCktBaseAlarmsEnabled	TruthValue
	alpsCktBaseConnType	INTEGER
	alpsCktBaseState	INTEGER
	alpsCktBaseNumActiveAscus	Integer32
	alpsCktBaseCurrentPeer	IpAddress
	alpsCktBaseLifeTimeTimer	TimeInterval
	alpsCktBaseHostLinkNumber	Integer32
	alpsCktBaseHostLinkType	INTEGER
	alpsCktBaseRemHld	Integer32
	alpsCktBaseLocalHld	Integer32
	alpsCktBaseDownReason	INTEGER
	alpsCktBaseOutPackets	Counter32
	alpsCktBaseOutOctets	Counter32
	alpsCktBaseInPackets	Counter32
	alpsCktBaseInOctets	Counter32
	alpsCktBaseDropsCktDisabled	Counter32
	alpsCktBaseDropsQOverflow	Counter32
	alpsCktBaseDropsLifeTimeExpd	Counter32
	alpsCktBaseEnabled	TruthValue
	alpsCktBaseRowStatus	RowStatus
	alpsCktBaseCurrPeerConnId	DisplayString

AlpsCktX25Entry
SEQUENCE
	alpsCktX25DlcType	INTEGER
	alpsCktX25IfIndex	InterfaceIndex
	alpsCktX25LCN	Integer32
	alpsCktX25HostX121	X121Address
	alpsCktX25RemoteX121	X121Address
	alpsCktX25DropsVcReset	Counter32

AlpsCktP1024Entry
SEQUENCE
	alpsCktP1024DlcType	INTEGER
	alpsCktP1024BackupPeerAddr	IpAddress
	alpsCktP1024RetryTimer	TimeInterval
	alpsCktP1024IdleTimer	TimeInterval
	alpsCktP1024EmtoxX121	X121Address
	alpsCktP1024Ax25LCN	Integer32
	alpsCktP1024WinOut	Integer32
	alpsCktP1024WinIn	Integer32
	alpsCktP1024OutPktSize	Integer32
	alpsCktP1024InPktSize	Integer32
	alpsCktP1024SvcMsgList	Integer32
	alpsCktP1024SvcMsgIntvl	TimeTicks
	alpsCktP1024DropsUnkAscu	Counter32
	alpsCktP1024RowStatus	RowStatus
	alpsCktP1024MatipCloseDelay	TimeInterval

AlpsCktAscuEntry
SEQUENCE
	alpsCktAscuCktName	AlpsCktName
	alpsCktAscuCktDlcType	INTEGER
	alpsCktAscuA1	AlpsAscuA1A2Value
	alpsCktAscuA2	AlpsAscuA1A2Value
	alpsCktAscuIfIndex	InterfaceIndex
	alpsCktAscuId	Integer32
	alpsCktAscuStatus	INTEGER

AlpsIfP1024Entry
SEQUENCE
	alpsIfP1024EncapType	INTEGER
	alpsIfP1024PollRespTimeout	TimeInterval
	alpsIfP1024GATimeout	TimeInterval
	alpsIfP1024PollPauseTimeout	TimeInterval
	alpsIfP1024MaxErrCnt	Integer32
	alpsIfP1024MaxRetrans	Integer32
	alpsIfP1024CurrErrCnt	Integer32
	alpsIfP1024MinGoodPollResp	Integer32
	alpsIfP1024PollingRatio	Integer32
	alpsIfP1024NumAscus	Gauge32
	alpsIfP1024ServMsgFormat	INTEGER
	alpsIfP1024ServMsgStatusChange	TruthValue
	alpsIfP1024ServMsgDropTermAddr	INTEGER

AlpsIfHLinkEntry
SEQUENCE
	alpsIfHLinkHostHld	Integer32
	alpsIfHLinkNumber	Integer32
	alpsIfHLinkX25ProtocolType	INTEGER
	alpsIfHLinkAx25PvcDamp	TimeInterval
	alpsIfHLinkEmtoxHostX121	X121Address
	alpsIfHLinkActiveCkts	Integer32

AlpsAscuEntry
SEQUENCE
	alpsAscuId	Integer32
	alpsAscuA1	AlpsAscuA1A2Value
	alpsAscuA2	AlpsAscuA1A2Value
	alpsAscuCktName	AlpsCktName
	alpsAscuAlarmsEnabled	TruthValue
	alpsAscuRetryOption	INTEGER
	alpsAscuMaxMsgLength	Integer32
	alpsAscuFwdStatusOption	TruthValue
	alpsAscuState	INTEGER
	alpsAscuDownReason	INTEGER
	alpsAscuOutPackets	Counter32
	alpsAscuOutOctets	Counter32
	alpsAscuInPackets	Counter32
	alpsAscuInOctets	Counter32
	alpsAscuDropsGarbledPkts	Counter32
	alpsAscuDropsAscuDown	Counter32
	alpsAscuDropsAscuDisabled	Counter32
	alpsAscuEnabled	TruthValue
	alpsAscuRowStatus	RowStatus
	alpsAscuAutoReset	TruthValue

AlpsSvcMsgEntry
SEQUENCE
	alpsSvcMsgListNum	Integer32
	alpsSvcMsgNum	Integer32
	alpsSvcMsg	DisplayString
	alpsSvcMsgRowStatus	RowStatus

AlpsX121ToIpTransEntry
SEQUENCE
	alpsX121	X121Address
	alpsIpAddress	IpAddress
	alpsX121ToIpTransRowStatus	RowStatus

Defined Values

ciscoAlpsMIB		1.3.6.1.4.1.9.9.95
The MIB module for Airline Protocol Support. ************************************************************** * Acronym Definitions * * * * ALPS : AirLine Protocol Support * * AX.25 : Airline X.25 * * EMTOX : Exchange of Mixed Traffic over X.25 * * ASCU : Agent Set Control Unit * * * ************************************************************** Overview of ALPS (AirLine Protocol Support) MIB ============================================== MIB description Document to refer: 'Configuring ALPS' section in Cisco IOS Command Reference & Configuration Guide. The ALPS MIB provides configuration and operational information for Cisco's Airline protocol support for IBM-P1024B(ALC) and Unisys-P1024C(UTS) protocols encapsulation over TCP/IP. The following entities are managed: 1. Peers 2. ALPS Circuits 3. ASCUs (Agent Set Control Units) 4. ALC interface 5. ALPS Host link interface to the host HOST(Emtox/Ax.25) <----> Central <---> IP Network <---> Remote <----> ASCU router router The router connected to the Host is called the Central router and the router connected to the ASCU is called the Remote router. We anticipate one Central router connecting to a large number of Remote routers. Each router has a local peer, which connects to its counterpart on the other router (referred to as the remote peer) via a TCP connection. ALPS circuits are set up over this TCP connection either on a permanent or on-demand basis. A logical grouping of ASCUs are connected via a single circuit - this has no connection to the physical interfaces that the ASCUs are connected to. The only restriction is that all the ASCUs should be directly connected to the same router. Multiple ASCUs can connect to a single serial interface and several terminals connect to an ASCU. However, terminals are not visible to the ALPS feature - the router talks only to the ASCUs. An ASCU can be identified by * the interface it is on and its Interface Address (IA) or * the circuit it is on, and its A1 and A2 values, which identify it within the circuit. Thus there are two ways of identifying an ASCU - or Circuit names are globally unique. The connection to the host is via one of two flavors of X.25 - either AX.25 (for PVCs) or EMTOX (for SVCs). Each X.25 VC corresponds to one ALPS circuit. There are several hostlinks between a host and the Central router and load balancing is done across these. EMTOX allows the host to dial out to a terminal. This requires the use of an X.121 to IP address translation table to connect to the appropriate remote peer.
MODULE-IDENTITY

ciscoAlpsMIBObjects		1.3.6.1.4.1.9.9.95.1
OBJECT IDENTIFIER

alpsGroups		1.3.6.1.4.1.9.9.95.1.1
OBJECT IDENTIFIER

alpsPeerObjects		1.3.6.1.4.1.9.9.95.1.2
OBJECT IDENTIFIER

alpsCktObjects		1.3.6.1.4.1.9.9.95.1.3
OBJECT IDENTIFIER

alpsIfObjects		1.3.6.1.4.1.9.9.95.1.4
OBJECT IDENTIFIER

alpsAscuObjects		1.3.6.1.4.1.9.9.95.1.5
OBJECT IDENTIFIER

alpsGlobalObjects		1.3.6.1.4.1.9.9.95.1.6
OBJECT IDENTIFIER

alpsPeer		1.3.6.1.4.1.9.9.95.1.2.1
OBJECT IDENTIFIER

alpsPeerLocalIpAddr		1.3.6.1.4.1.9.9.95.1.2.1.1
The configured IP address used by the ALPS component in this router.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

alpsPeerLocalAtpPort		1.3.6.1.4.1.9.9.95.1.2.1.2
The port number used locally by the ALPS peer at this router. This is a static value but the port number used can change in later versions. This is not a configured value but is embedded into the source code. This has been provided mainly to aid in debugging so that the operator knows which TCP port to look at. ATP is the ALPS Tunnelling Protocol, a Cisco proprietary way to tunnel ALPS data across a TCP link
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

alpsPeerKeepaliveTimeout		1.3.6.1.4.1.9.9.95.1.2.1.3
The TCP keep alive timeout value for Local ALPS Peer. Keepalives are sent out periodically at this interval to the remote peer.
Status: current	Access: read-write
OBJECT-TYPE
	TimeInterval

alpsPeerKeepaliveMaxRetries		1.3.6.1.4.1.9.9.95.1.2.1.4
The number of keepalives sent with acknowledgement before declaring the remote peer dead. 0 implies that keepalives are turned off.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..10

alpsPeerInCallsAcceptFlag		1.3.6.1.4.1.9.9.95.1.2.1.5
If this is true, calls are accepted from any peer. If this is false, calls are accepted only from those routers which have been explicitly configured using alps remote-peer commands.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

alpsRemPeerTable		1.3.6.1.4.1.9.9.95.1.2.2
A list of Remote peers that the local ALPS peer can communicate with.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsRemPeerEntry

alpsRemPeerEntry		1.3.6.1.4.1.9.9.95.1.2.2.1
Each entry represents an Remote ALPS Peer.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	AlpsRemPeerEntry

alpsRemPeerIpAddr		1.3.6.1.4.1.9.9.95.1.2.2.1.1
The remote IP address for the TCP Connection.
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	IpAddress

alpsRemPeerConnType		1.3.6.1.4.1.9.9.95.1.2.2.1.2
Type of ALPS circuit established. Dynamic circuits are established only when there is data traffic that needs to be sent across and are closed when the alpsRemPeerIdleTimer expires. Permanent circuits stay up regardless of whether there is traffic across them or not.
Status: deprecated	Access: read-create
OBJECT-TYPE
	INTEGER	permanent(1), dynamic(2)

alpsRemPeerLocalPort		1.3.6.1.4.1.9.9.95.1.2.2.1.3
The port number used locally by the tcp connection for the circuit. the initiator of a connection will dynamically assign a port number. the other end of the connection will have a well-known port number applicable to the encapsulation used by the connection - e.g. the value of alpsPeerLocalAtpPort for ATP connections.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

alpsRemPeerRemotePort		1.3.6.1.4.1.9.9.95.1.2.2.1.4
The port number used by the remote end of the tcp connection for the circuit. the initiator of a connection will dynamically assign a port number. the other end of the connection will have a well-known port number applicable to the encapsulation used by the connection - e.g. the value of alpsPeerLocalAtpPort for ATP connections. If this connection was initiated by the local router, a port number will be dynamically selected. Otherwise the value of alpsPeerLocalAtpPort will be used (for ATP connections)
Status: deprecated	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

alpsRemPeerState		1.3.6.1.4.1.9.9.95.1.2.2.1.5
TCP Peer State. Initially the connection is in the closed state. For permanent connections, it starts opening the TCP connection immediately, but for dynamic ones, it waits till there is traffic addressed to the remote peer. It then progresses via opening into the opened state.
Status: deprecated	Access: read-only
OBJECT-TYPE
	INTEGER	closed(1), opening(2), opened(3)

alpsRemPeerUptime		1.3.6.1.4.1.9.9.95.1.2.2.1.6
Time elapsed since TCP connection was established.
Status: deprecated	Access: read-only
OBJECT-TYPE
	TimeTicks

alpsRemPeerNumActiveCkts		1.3.6.1.4.1.9.9.95.1.2.2.1.7
Number of active ALPS circuits in this TCP session.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Gauge32

alpsRemPeerIdleTimer		1.3.6.1.4.1.9.9.95.1.2.2.1.8
The TCP session with the peer will be closed if there is no activity for alpsInactiveTimer seconds. This is valid only for dynamic circuits
Status: deprecated	Access: read-create
OBJECT-TYPE
	TimeInterval

alpsRemPeerAlarmsEnabled		1.3.6.1.4.1.9.9.95.1.2.2.1.9
Specifies whether alarms are generated for this remote Peer
Status: deprecated	Access: read-create
OBJECT-TYPE
	TruthValue

alpsRemPeerTCPQlen		1.3.6.1.4.1.9.9.95.1.2.2.1.10
Maximum TCP Queue size allowed for this TCP session.
Status: deprecated	Access: read-create
OBJECT-TYPE
	Integer32	1..200

alpsRemPeerOutPackets		1.3.6.1.4.1.9.9.95.1.2.2.1.11
Number of packets transmitted to the remote peer.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerOutOctets		1.3.6.1.4.1.9.9.95.1.2.2.1.12
Number of octets transmitted to the remote peer.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerInPackets		1.3.6.1.4.1.9.9.95.1.2.2.1.13
Number of packets received from the remote peer.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerInOctets		1.3.6.1.4.1.9.9.95.1.2.2.1.14
Number of octets received from the remote peer.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerDropsGiant		1.3.6.1.4.1.9.9.95.1.2.2.1.15
Number of Packets dropped because they were larger than the maximum allowed packet size of 3840 bytes.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerDropsQFull		1.3.6.1.4.1.9.9.95.1.2.2.1.16
Number of packets dropped because the TCP queue (of size alpsRemPeerTCPQlen) was full.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerDropsPeerUnreach		1.3.6.1.4.1.9.9.95.1.2.2.1.17
Number of packets dropped because remote peer was unreachable.
Status: deprecated	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerRowStatus		1.3.6.1.4.1.9.9.95.1.2.2.1.18
This object is used to create a new row or modify or delete an existing row in this table.
Status: deprecated	Access: read-create
OBJECT-TYPE
	RowStatus

alpsRemPeerCfgTable		1.3.6.1.4.1.9.9.95.1.2.3
Table listing of all administered ALPS remote peer configuration entries on this node. Entries in this table can be created via a CLI command or via alpsRemPeerCfgRowStatus.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsRemPeerCfgEntry

alpsRemPeerCfgEntry		1.3.6.1.4.1.9.9.95.1.2.3.1
Each entry represents an ALPS remote peer configuration entry on this node.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsRemPeerCfgEntry

alpsRemPeerCfgIpAddr		1.3.6.1.4.1.9.9.95.1.2.3.1.1
The configured IP address of an ALPS remote peer.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

alpsRemPeerCfgProtocol		1.3.6.1.4.1.9.9.95.1.2.3.1.2
The configured ALPS protocol encapsulation. This protocol encapsulation is at the layer above TCP.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	atp(1), matipTypeA(2)

alpsRemPeerCfgActivation		1.3.6.1.4.1.9.9.95.1.2.3.1.3
The configured type of ALPS peer activation.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	permanent(1), dynamic(2)

alpsRemPeerCfgTCPQLen		1.3.6.1.4.1.9.9.95.1.2.3.1.4
The configured maximum TCP Queue size.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..100

alpsRemPeerCfgIdleTimer		1.3.6.1.4.1.9.9.95.1.2.3.1.5
The configured idle timer for a dynamic activation peer.
Status: current	Access: read-create
OBJECT-TYPE
	TimeInterval

alpsRemPeerCfgNoCircTimer		1.3.6.1.4.1.9.9.95.1.2.3.1.6
The configured no-circuit timer for a dynamic activation peer.
Status: current	Access: read-create
OBJECT-TYPE
	TimeInterval

alpsRemPeerCfgAlarmsOn		1.3.6.1.4.1.9.9.95.1.2.3.1.7
The configured parameter which specifies whether alarms are generated for remote peer connections to the IP address in alpsRemPeerCfgIpAddr.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alpsRemPeerCfgStatIntvl		1.3.6.1.4.1.9.9.95.1.2.3.1.8
The configured status interval timer.
Status: current	Access: read-create
OBJECT-TYPE
	TimeInterval

alpsRemPeerCfgStatRetry		1.3.6.1.4.1.9.9.95.1.2.3.1.9
The configured number of status retries.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..100

alpsRemPeerCfgRowStatus		1.3.6.1.4.1.9.9.95.1.2.3.1.10
This object is used to create a new row or modify or delete an existing row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alpsRemPeerConnTable		1.3.6.1.4.1.9.9.95.1.2.4
Table listing of all ALPS remote peer connections on this node.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsRemPeerConnEntry

alpsRemPeerConnEntry		1.3.6.1.4.1.9.9.95.1.2.4.1
Each entry represents an ALPS remote peer connection on this node.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsRemPeerConnEntry

alpsRemPeerConnIpAddr		1.3.6.1.4.1.9.9.95.1.2.4.1.1
The IP address of the ALPS remote peer.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

alpsRemPeerConnIdString		1.3.6.1.4.1.9.9.95.1.2.4.1.2
A descriptive ASCII string that is used to distinguish among different peer connections to the same ALPS remote peer IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString	Size(1..20)

alpsRemPeerConnLocalPort		1.3.6.1.4.1.9.9.95.1.2.4.1.3
The local TCP port number used by the underlying TCP connection to an ALPS remote peer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

alpsRemPeerConnForeignPort		1.3.6.1.4.1.9.9.95.1.2.4.1.4
The foreign (remote) TCP port number used by the underlying TCP connection to an ALPS remote peer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

alpsRemPeerConnState		1.3.6.1.4.1.9.9.95.1.2.4.1.5
The state of the connection to an ALPS remote peer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	closed(1), opening(2), opened(3), busy(4)

alpsRemPeerConnProtocol		1.3.6.1.4.1.9.9.95.1.2.4.1.6
The ALPS protocol encapsulation used on the connection to the ALPS remote peer. This protocol encapsulation is a layer above TCP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	atp(1), matipTypeA(2)

alpsRemPeerConnCreation		1.3.6.1.4.1.9.9.95.1.2.4.1.7
The stimulus for creating the peer connection object. The peer connection object may be created solely due to configuration (admin) or due to a combination of configuration and protocol events (learned).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	admin(1), learned(2)

alpsRemPeerConnActivation		1.3.6.1.4.1.9.9.95.1.2.4.1.8
Basis for activation a peer connection. A permanent activation peer connection will attempt to open immediately and stay open, regardless of the usage of the peer connection. A dynamic activation peer connection only opens when there is data to send and the peer connection will close if there are no data messages sent or received across the peer for the duration of the idle timer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	permanent(1), dynamic(2)

alpsRemPeerConnUptime		1.3.6.1.4.1.9.9.95.1.2.4.1.9
Elapsed time since the ALPS peer connection was successfully established.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

alpsRemPeerConnNumActCirc		1.3.6.1.4.1.9.9.95.1.2.4.1.10
The number of ALPS virtual circuits using the connection to this ALPS remote peer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

alpsRemPeerConnLastTxRx		1.3.6.1.4.1.9.9.95.1.2.4.1.11
The value of sysUpTime when a peer data message was last transmitted or received across this ALPS remote peer connection. This timestamp is not update if the peer message is a peer status inquiry/response message.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

alpsRemPeerConnLastRxAny		1.3.6.1.4.1.9.9.95.1.2.4.1.12
The value of sysUpTime when a peer data or status message is last received across the ALPS remote peer connection.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

alpsRemPeerConnIdleTimer		1.3.6.1.4.1.9.9.95.1.2.4.1.13
A dynamic activation ALPS peer connection will be closed if zero peer data messages are sent or received for a length of time greater than or equal to this timer.
Status: current	Access: read-only
OBJECT-TYPE
	TimeInterval

alpsRemPeerConnNoCircTimer		1.3.6.1.4.1.9.9.95.1.2.4.1.14
A dynamic activation ALPS peer connection will be closed if zero ALPS circuits are active or attempt to activate for a length of time greater than or equal to this timer.
Status: current	Access: read-only
OBJECT-TYPE
	TimeInterval

alpsRemPeerConnTCPQLen		1.3.6.1.4.1.9.9.95.1.2.4.1.15
The maximum number of ALPS peer messages that can be queued in a single TCP session.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..100

alpsRemPeerConnAlarmsOn		1.3.6.1.4.1.9.9.95.1.2.4.1.16
This parameter specifies whether ALPS alarms are generated for this ALPS remote peer connection.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

alpsRemPeerConnStatIntvl		1.3.6.1.4.1.9.9.95.1.2.4.1.17
The time interval (in seconds) between transmission of consecutive ALPS Peer Status messages. These messages are only transmitted if zero messages are received on the peer connection for a length of time greater than or equal to this timer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..300

alpsRemPeerConnStatRetry		1.3.6.1.4.1.9.9.95.1.2.4.1.18
The number of consecutive unanswered ALPS Peer Status messages transmitted before closing the conenction to the ALPS remote peer.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..100

alpsRemPeerConnDownReason		1.3.6.1.4.1.9.9.95.1.2.4.1.19
Reason that an ALPS Peer connection failed to open sauccessfully.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), idle(2), noCircuits(3), destUnreachable(4), foreignReset(5), localReset(6), noMemory(7), openingTimeout(8)

alpsRemPeerConnOutPackets		1.3.6.1.4.1.9.9.95.1.2.4.1.20
Number of packets transmitted on this ALPS remote peer connection.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerConnOutOctets		1.3.6.1.4.1.9.9.95.1.2.4.1.21
Number of octets transmitted on this ALPS remote peer connection.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerConnInPackets		1.3.6.1.4.1.9.9.95.1.2.4.1.22
Number of packets received on this ALPS remote peer connection.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerConnInOctets		1.3.6.1.4.1.9.9.95.1.2.4.1.23
Number of octets received on this ALPS remote peer connection.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerConnDropsGiant		1.3.6.1.4.1.9.9.95.1.2.4.1.24
Number of ALPS peer packets dropped due to exceeding the maximum allowed packet size of 3840 bytes.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerConnDropsQFull		1.3.6.1.4.1.9.9.95.1.2.4.1.25
Number of ALPS peer packets dropped because the TCP output queue is full.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerConnDropsUnreach		1.3.6.1.4.1.9.9.95.1.2.4.1.26
Number of ALPS peer packets dropped because the ALPS remote peer is unreachable.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsRemPeerConnDropsVersion		1.3.6.1.4.1.9.9.95.1.2.4.1.27
Number of ALPS peer packets dropped because of a version mismatch in the ALPS encapsulation.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsCktBaseTable		1.3.6.1.4.1.9.9.95.1.3.1
A list of ALPS circuits. This table contains variables common to central & remote routers.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsCktBaseEntry

alpsCktBaseEntry		1.3.6.1.4.1.9.9.95.1.3.1.1
Details of ALPS Circuits.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsCktBaseEntry

alpsCktBaseName		1.3.6.1.4.1.9.9.95.1.3.1.1.1
Specifies the ALPS Circuit Name. This is unique within the network.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsCktName

alpsCktBaseDlcType		1.3.6.1.4.1.9.9.95.1.3.1.1.2
Specifies what type of circuit this is. The X25 circuit is set up with the same name as the P1024 circuit so we need this variable to distinguish between the two, in case local switching is done.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	emtox(1), ax25(2), alc(3), uts(4)

alpsCktBasePriPeerAddr		1.3.6.1.4.1.9.9.95.1.3.1.1.3
This is the IP address of the Primary Central peer. It is mandatory to configure a primary peer, but the backup peer is optional.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

alpsCktBaseAlarmsEnabled		1.3.6.1.4.1.9.9.95.1.3.1.1.4
Specifies whether alarms are generated for this ALPS circuit. Alarms can be syslog messages or SNMP traps - both are controlled using the same flags.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alpsCktBaseConnType		1.3.6.1.4.1.9.9.95.1.3.1.1.5
Specifies the ALPS Circuit Connection Type.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	permanent(1), dynamic(2)

alpsCktBaseState		1.3.6.1.4.1.9.9.95.1.3.1.1.6
Indicates the state of ALPS Circuit.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), inoperable(2), opening(3), opened(4), cktBusy(5), peerBusy(6), updating(7)

alpsCktBaseNumActiveAscus		1.3.6.1.4.1.9.9.95.1.3.1.1.7
Reports the number of enabled ASCUs that are attached to this ALPS Circuit. Attachment of an ASCU to an ALPS circuit may occur due to configuration or due to information passed in a protocol message.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..64

alpsCktBaseCurrentPeer		1.3.6.1.4.1.9.9.95.1.3.1.1.8
Reports the IP address of the peer that this ALPS circuit is currently connected to.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

alpsCktBaseLifeTimeTimer		1.3.6.1.4.1.9.9.95.1.3.1.1.9
A data message that has been queued within the router for longer than this interval will be dropped.
Status: current	Access: read-create
OBJECT-TYPE
	TimeInterval

alpsCktBaseHostLinkNumber		1.3.6.1.4.1.9.9.95.1.3.1.1.10
Specifies host link number (on Central router) for this ALPS Circuit. The host link number is used to provide a degree of transparency to the remote router. A single host link may correspond to multiple physical links between the central router and the host, which can then load-balance VCs across them.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..255

alpsCktBaseHostLinkType		1.3.6.1.4.1.9.9.95.1.3.1.1.11
Specifies host link type(on Central router) for this ALPS Circuit.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ax25(1), emtox(2)

alpsCktBaseRemHld		1.3.6.1.4.1.9.9.95.1.3.1.1.12
Specifies the HLD (High-level descriptor) of the AX.25/EMTOX host for this ALPS Circuit. This serves as an identifier for the host
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..32639

alpsCktBaseLocalHld		1.3.6.1.4.1.9.9.95.1.3.1.1.13
Specifies the local HLD for this ALPS Circuit. HLDs are required at the host for both ends of the connection.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..32639

alpsCktBaseDownReason		1.3.6.1.4.1.9.9.95.1.3.1.1.14
Reports the reason why this ALPS Circuit is down, if it is down.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), noReason(2), hostLinkDown(3), cktDisabled(4), hostLinkDisabled(5), noHostLinkMatched(6), noHldMatched(7), cktNameInUse(8), pvcLcnOutOfRange(9), x25ParamInvalid(10), cktOpeningTimeout(11), x25ClearDteNoReason(12), configMismatch(13), noResourcesAvail(14), incompatibleA1A2(15), cktIdle(16), peerDown(17), noAscusConfigured(18), x25ClearHostUnknown(19), x25ClearHostDown(20), x25ClearHostDisabled(21), x25ClearHostSaturated(22), x25ClearCallerUnknown(23), x25ClearCallerUnauth(24), x25ClearConfigRejected(25), x25ClearConfigFallback(26), x25ClearConfigIncompat(27), x25ClearHLDUnknown(28), x25ClearPIDUnknown(29), x25ClearFacilRejected(30), x25ClearNetNoReason(31), pvcLcnInUse(32), noSvcLcnAvail(33), peerIdle(34), presUnknown(35), presMismatch(36), openMsgTooShort(37), mpxUnknown(38), mpxHdrMismatch(39), trafTypeMismatch(40), codingMismatch(41), ascuInSession(42)

alpsCktBaseOutPackets		1.3.6.1.4.1.9.9.95.1.3.1.1.15
Number of packets transmitted to remote peer over this circuit.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsCktBaseOutOctets		1.3.6.1.4.1.9.9.95.1.3.1.1.16
Number of octets transmitted to remote peer over this circuit.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsCktBaseInPackets		1.3.6.1.4.1.9.9.95.1.3.1.1.17
Number of packets received from remote peer over this circuit.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsCktBaseInOctets		1.3.6.1.4.1.9.9.95.1.3.1.1.18
Number of octets received from remote peer over this circuit.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsCktBaseDropsCktDisabled		1.3.6.1.4.1.9.9.95.1.3.1.1.19
Number of packets dropped because the circuit was disabled. This would typically be packets that were queueued before the circuit was disabled which are now left in the queue.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsCktBaseDropsQOverflow		1.3.6.1.4.1.9.9.95.1.3.1.1.20
Number of packets dropped due to TCP Congestion.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsCktBaseDropsLifeTimeExpd		1.3.6.1.4.1.9.9.95.1.3.1.1.21
Number of packets which were queued within the router for longer than alpsCktBaseLifeTimeTimer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsCktBaseEnabled		1.3.6.1.4.1.9.9.95.1.3.1.1.22
This specifies if the circuit has been enabled. After a circuit has been configured, it must be explicitly enabled in order for the circuit to be set up.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alpsCktBaseRowStatus		1.3.6.1.4.1.9.9.95.1.3.1.1.23
This object is used to create a new row or modify or delete an existing row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alpsCktBaseCurrPeerConnId		1.3.6.1.4.1.9.9.95.1.3.1.1.24
A descriptive ASCII string that is used to distinguish among different peer connections to the same ALPS remote peer IP address.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..20)

alpsCktX25Table		1.3.6.1.4.1.9.9.95.1.3.2
A list of ALPS X.25 circuits. These entries exist only for X.25 circuits. hence this table would probably be empty at the remote router
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsCktX25Entry

alpsCktX25Entry		1.3.6.1.4.1.9.9.95.1.3.2.1
Details of ALPS Circuits.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsCktX25Entry

alpsCktX25DlcType		1.3.6.1.4.1.9.9.95.1.3.2.1.1
Specifies what type of circuit this is.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	emtox(1), ax25(2)

alpsCktX25IfIndex		1.3.6.1.4.1.9.9.95.1.3.2.1.2
Reports the interface the circuit is on. This is the interface which is connected to the host
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

alpsCktX25LCN		1.3.6.1.4.1.9.9.95.1.3.2.1.3
The Logical Channel Number being used on the X.25 VC for this ALPS Circuit.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4096

alpsCktX25HostX121		1.3.6.1.4.1.9.9.95.1.3.2.1.4
The X.121 address on the host side which the central router uses to connect to the host
Status: current	Access: read-only
OBJECT-TYPE
	X121Address

alpsCktX25RemoteX121		1.3.6.1.4.1.9.9.95.1.3.2.1.5
X.121 address of the remote side. Remote here refers to the side that the ASCUS are connected to and is also referred to as the remote router.
Status: current	Access: read-only
OBJECT-TYPE
	X121Address

alpsCktX25DropsVcReset		1.3.6.1.4.1.9.9.95.1.3.2.1.6
Number of packets dropped due to the VC being reset. These are packets that were queued up for transmission on that VC when it was reset
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsCktP1024Table		1.3.6.1.4.1.9.9.95.1.3.3
A list of ALC or UTS Alps circuits.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsCktP1024Entry

alpsCktP1024Entry		1.3.6.1.4.1.9.9.95.1.3.3.1
Details of ALPS Circuits.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsCktP1024Entry

alpsCktP1024DlcType		1.3.6.1.4.1.9.9.95.1.3.3.1.1
Specifies what type of circuit this is.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	alc(3), uts(4)

alpsCktP1024BackupPeerAddr		1.3.6.1.4.1.9.9.95.1.3.3.1.2
This is the IP address of the backup remote peer. This is optional and hence may not always exist.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

alpsCktP1024RetryTimer		1.3.6.1.4.1.9.9.95.1.3.3.1.3
Specifies the interval at which a permanent ALPS circuit will attempt to reestablish the circuit in case it wasn't able to come up.
Status: current	Access: read-create
OBJECT-TYPE
	TimeInterval

alpsCktP1024IdleTimer		1.3.6.1.4.1.9.9.95.1.3.3.1.4
If there is no traffic on a dynamic ALPS circuit for this interval, it will be cleared.
Status: current	Access: read-create
OBJECT-TYPE
	TimeInterval

alpsCktP1024EmtoxX121		1.3.6.1.4.1.9.9.95.1.3.3.1.5
Specifies the X.121 address of the SVC established with EMTOX host. This field should be set to length zero in the case of PVCs (AX.25 host).
Status: current	Access: read-create
OBJECT-TYPE
	X121Address

alpsCktP1024Ax25LCN		1.3.6.1.4.1.9.9.95.1.3.3.1.6
Specifies the Logical Channel Number being used on the PVC established with AX.25 host. This field should be set to zero in the case of SVCs (EMTOX host).
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..4096

alpsCktP1024WinOut		1.3.6.1.4.1.9.9.95.1.3.3.1.7
Specifies X.25 transmit Window size on the Logical Channel Number of this ALPS Circuit.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..7

alpsCktP1024WinIn		1.3.6.1.4.1.9.9.95.1.3.3.1.8
Specifies the X.25 receive Window size on the Logical Channel Number of this ALPS Circuit.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..7

alpsCktP1024OutPktSize		1.3.6.1.4.1.9.9.95.1.3.3.1.9
Specifies the X.25 maxiumum output Packet size on the Logical Channel Number of this ALPS Circuit. The default output Packet size for AX.25 is 240 bytes and 128 bytes for EMTOX.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	128..4096

alpsCktP1024InPktSize		1.3.6.1.4.1.9.9.95.1.3.3.1.10
Specifies X.25 maximum input Packet size on the Logical Channel Number of this ALPS Circuit. The default input Packet size for AX.25 is 240 bytes and 128 bytes for EMTOX.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	128..4096

alpsCktP1024SvcMsgList		1.3.6.1.4.1.9.9.95.1.3.3.1.11
Specifies the Service Message List Number to use on this ALPS Circuit. This allows custom service messages to be sent for ASCUs on a particular circuit. Service messages are sent out by the router to the ASCU when abnormal conditions occur, and are displayed on the terminal. There is a default set of service messages, usually referred to as List 0. However, it is possible to configure custom sets of service messages for display, selectable on a per-circuit basis.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	0..8

alpsCktP1024SvcMsgIntvl		1.3.6.1.4.1.9.9.95.1.3.3.1.12
Specifies Service Message Time Interval for the Service messages to be sent this ALPS Circuit. This controls how frequently the messages are repeated when an error condition (e.g. network being down) persists.
Status: current	Access: read-create
OBJECT-TYPE
	TimeTicks

alpsCktP1024DropsUnkAscu		1.3.6.1.4.1.9.9.95.1.3.3.1.13
Number of packets that were found to be from an Unknown ASCU (i.e. an ASCU that had not been configured) and hence were dropped.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsCktP1024RowStatus		1.3.6.1.4.1.9.9.95.1.3.3.1.14
This object is used to create a new row or modify or delete an existing row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alpsCktP1024MatipCloseDelay		1.3.6.1.4.1.9.9.95.1.3.3.1.15
Specifies the minumum delay between transmission of a MATIP Close and the transmission of a MATIP Session Open for this ALPS circuit.
Status: current	Access: read-create
OBJECT-TYPE
	TimeInterval

alpsCktAscuTable		1.3.6.1.4.1.9.9.95.1.3.4
A list of ASCUs for each ALPS Circuit. This may not include all ASCUs which have this circuit configured as alpsAscuCktName because some ASCUs may be rejected by the host while setting up the circuit.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsCktAscuEntry

alpsCktAscuEntry		1.3.6.1.4.1.9.9.95.1.3.4.1
Details of ASCUs on ASCU Circuits.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsCktAscuEntry

alpsCktAscuCktName		1.3.6.1.4.1.9.9.95.1.3.4.1.1
The name of the ALPS circuit which this ASCU is on. The circuit may be always up (for permanent circuits) or get set up (dynamic circuits) when there is traffic on one of the ASCUs which are set up for that circuit.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsCktName

alpsCktAscuCktDlcType		1.3.6.1.4.1.9.9.95.1.3.4.1.2
Specifies what type of circuit this is. The X.25 circuit is set up with the same name as the ALC circuit so we need this variable to distinguish between the two.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	emtox(1), ax25(2), alc(3), uts(4)

alpsCktAscuA1		1.3.6.1.4.1.9.9.95.1.3.4.1.3
A1 value. This is used along with the alpsCktAscuA2 value to identify the ASCU within the circuit.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsAscuA1A2Value

alpsCktAscuA2		1.3.6.1.4.1.9.9.95.1.3.4.1.4
A2 value. This is used along with the alpsCktAscuA1 value to identify the ASCU within the circuit.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsAscuA1A2Value

alpsCktAscuIfIndex		1.3.6.1.4.1.9.9.95.1.3.4.1.5
Reports the interface the ASCU is on. This field, along with alpsCktAscuId is provided so that it is possible to correlate this information with the configured ASCU information in alpsAscuTable
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndex

alpsCktAscuId		1.3.6.1.4.1.9.9.95.1.3.4.1.6
Reports the ASCU Identifier which uniquely identifies an ASCU on a given interface. This value is the Interface Address (IA) for ALC and the Remote Identifier (RID) for UTS. A value of 0 indicates that the ASCU id is either unavailable or not applicable.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..127

alpsCktAscuStatus		1.3.6.1.4.1.9.9.95.1.3.4.1.7
Reports the ASCU status - ASCUs configured on the circuit can be rejected at the host and would then be marked REJECT. Also, ASCUs configured after the circuit has been established are not added dynamically to the circuit but are marked NEW and get added when the circuit gets established the next time. ASCUs waiting for an accept or reject response from the host are marked as PENDING. ASCUs that were accepted by the host are marked OK.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), ok(2), reject(3), new(4), pending(5)

alpsIfP1024Table		1.3.6.1.4.1.9.9.95.1.4.1
A list of interfaces running the P1024B or P1024C protocols
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsIfP1024Entry

alpsIfP1024Entry		1.3.6.1.4.1.9.9.95.1.4.1.1
Interface Details
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsIfP1024Entry

alpsIfP1024EncapType		1.3.6.1.4.1.9.9.95.1.4.1.1.1
Reports the encapsulation type for this Serial Interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	alc(1), uts(2)

alpsIfP1024PollRespTimeout		1.3.6.1.4.1.9.9.95.1.4.1.1.2
Specifies the Poll Response Time out value.
Status: current	Access: read-write
OBJECT-TYPE
	TimeInterval

alpsIfP1024GATimeout		1.3.6.1.4.1.9.9.95.1.4.1.1.3
Specifies the time-out delay between receipt of first character of an input sequence solicited by a poll and receipt of GA sequence.
Status: current	Access: read-write
OBJECT-TYPE
	TimeInterval

alpsIfP1024PollPauseTimeout		1.3.6.1.4.1.9.9.95.1.4.1.1.4
Specifies the minimum delay between two poll cycles. Thus the poll pause interval is counted from the instant when the first ASCU in the poll list is polled. Note that this is the delay between two traversals of the entire poll list rather than the interval between two consecutive polls. The actual delay will probably be more than the value of this variable.
Status: current	Access: read-write
OBJECT-TYPE
	TimeInterval

alpsIfP1024MaxErrCnt		1.3.6.1.4.1.9.9.95.1.4.1.1.5
Specifies a maximum error count for this interface. After an ASCU link comes up, if it experiences this number of errors the ASCU link will be shutdown. The default value of 0 results in the ASCU link never being shutdown.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..30

alpsIfP1024MaxRetrans		1.3.6.1.4.1.9.9.95.1.4.1.1.6
Specifies the maximum number of times an output message will be retransmitted before it is discarded. This is relevant only for P1024C (UTS). For ALC, a value of 0 will be returned. Note that legal values for UTS are 1-10
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..10

alpsIfP1024CurrErrCnt		1.3.6.1.4.1.9.9.95.1.4.1.1.7
Reports the number of errors currently existing for this ASCU link. When this equals alpsIfP1024MaxErrCnt then the ASCU link will be shut down, unless alpsIfP1024MaxErrCnt equals 0 in which case the ascu link is never shut down due to error thresholds being exceeded
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..30

alpsIfP1024MinGoodPollResp		1.3.6.1.4.1.9.9.95.1.4.1.1.8
Specifies the number of good Poll Responses to be received from an ASCU before it can be declared up.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..30

alpsIfP1024PollingRatio		1.3.6.1.4.1.9.9.95.1.4.1.1.9
Specifies how many times ASCUs in UP state are polled before an ASCU in DOWN state is polled again.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..30

alpsIfP1024NumAscus		1.3.6.1.4.1.9.9.95.1.4.1.1.10
Reports the number of ASCUs configured on this Serial Port.
Status: current	Access: read-only
OBJECT-TYPE
	Gauge32

alpsIfP1024ServMsgFormat		1.3.6.1.4.1.9.9.95.1.4.1.1.11
Specifies the format of the service message sent to an ASCU on this interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	sita(1), apollo(2)

alpsIfP1024ServMsgStatusChange		1.3.6.1.4.1.9.9.95.1.4.1.1.12
Specifies whether service messages generated due to an ALPS circuit status change or an ASCU status change, will be forwarded to the ASCU.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

alpsIfP1024ServMsgDropTermAddr		1.3.6.1.4.1.9.9.95.1.4.1.1.13
Specifies whether the service message will be sent to the same terminal address of the dropped message or the configured value.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	msgterm(1), configterm(2)

alpsIfHLinkTable		1.3.6.1.4.1.9.9.95.1.4.2
A list of interfaces running AX.25/EMTOX host link protocols. These are on the central router
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsIfHLinkEntry

alpsIfHLinkEntry		1.3.6.1.4.1.9.9.95.1.4.2.1
Details of AX.25/EMTOX host link protocols on an Interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsIfHLinkEntry

alpsIfHLinkHostHld		1.3.6.1.4.1.9.9.95.1.4.2.1.1
Specifies the HLD of the AX.25/EMTOX host connected on this Interface. The HLD(High-level descriptor) serves as an identifier along with the hostlink number and helps correlate the ALPS circuit to a host link. The hex range is 0x1 to 0xFFFF which corresponds to 1 ... 65535 in decimal.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

alpsIfHLinkNumber		1.3.6.1.4.1.9.9.95.1.4.2.1.2
Specifies the configured Host Link Number on this Serial Interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..255

alpsIfHLinkX25ProtocolType		1.3.6.1.4.1.9.9.95.1.4.2.1.3
Reports the encapsulation type for this Serial Interface - AX.25 or EMTOX.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ax25(1), emtox(2)

alpsIfHLinkAx25PvcDamp		1.3.6.1.4.1.9.9.95.1.4.2.1.4
The purpose of this object is to handle the link-damping for an AX.25 host. If the PVC goes inactive (i.e. link goes down, etc...) for PVCDampValue seconds, then PVC will be destroyed as well as the associated ALPS circuit.
Status: current	Access: read-only
OBJECT-TYPE
	TimeInterval

alpsIfHLinkEmtoxHostX121		1.3.6.1.4.1.9.9.95.1.4.2.1.5
Specfies the X.121 address of this EMTOX host.
Status: current	Access: read-only
OBJECT-TYPE
	X121Address

alpsIfHLinkActiveCkts		1.3.6.1.4.1.9.9.95.1.4.2.1.6
Reports the number of ALPS Ckts established with this host.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..4096

alpsAscuTable		1.3.6.1.4.1.9.9.95.1.5.1
A list of ALPS ASCUs on an interface. This is defined only at the remote router.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsAscuEntry

alpsAscuEntry		1.3.6.1.4.1.9.9.95.1.5.1.1
Details of ASCU.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsAscuEntry

alpsAscuId		1.3.6.1.4.1.9.9.95.1.5.1.1.1
Specifies the ASCU Identifier and uniquely identifies an ASCU on a given interface. This value is the Interface Address (IA) for ALC and the Remote Identifier (RID) for UTS. This uniquely identifies an ASCU on a given interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..127

alpsAscuA1		1.3.6.1.4.1.9.9.95.1.5.1.1.2
A1 value of the ASCU.
Status: current	Access: read-create
OBJECT-TYPE
	AlpsAscuA1A2Value

alpsAscuA2		1.3.6.1.4.1.9.9.95.1.5.1.1.3
A2 value of the ASCU.
Status: current	Access: read-create
OBJECT-TYPE
	AlpsAscuA1A2Value

alpsAscuCktName		1.3.6.1.4.1.9.9.95.1.5.1.1.4
Specifies the ALPS Circuit Name for the circuit that is to be used for this ASCU's data. Note that all ASCUs on a physical interface may not use the same ALPS circuit to connect to the central router
Status: current	Access: read-create
OBJECT-TYPE
	AlpsCktName

alpsAscuAlarmsEnabled		1.3.6.1.4.1.9.9.95.1.5.1.1.5
Specifies whether alarms (syslog messages or SNMP traps) will be generated for this ASCU.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alpsAscuRetryOption		1.3.6.1.4.1.9.9.95.1.5.1.1.6
Specifies the retry option for this ASCU. This specifies the error message to be sent to the terminal when a message is dropped at the router. The terminal has three choices - either retransmit the last message (if the terminal can buffer it), re-enter the last message sent or do nothing. Based on the terminal's capabilities, one of these three is configured for the ASCU. Note that this option is the same for all terminals connected to an ASCU because the ALPS feature does not handle individual terminals
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	resend(1), reenter(2), none(3)

alpsAscuMaxMsgLength		1.3.6.1.4.1.9.9.95.1.5.1.1.7
Specifies Maximum length of Input Message that can be received from this ASCU.
Status: current	Access: read-create
OBJECT-TYPE
	Integer32	1..3840

alpsAscuFwdStatusOption		1.3.6.1.4.1.9.9.95.1.5.1.1.8
If this flag is set, status messages received from the ASCU are forwarded to the host. Otherwise they are discarded. Note that these are relevant only for P1024C (UTS). For ALC, a value of FALSE will be returned.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alpsAscuState		1.3.6.1.4.1.9.9.95.1.5.1.1.9
Reports the current ASCU Status. ASCUs are initially in disabled state. They are enabled from the parser if the operator wants to. This takes them to an UP state from which they go to a DOWN state if there are too many errors.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), unknown(2), down(3), up(4)

alpsAscuDownReason		1.3.6.1.4.1.9.9.95.1.5.1.1.10
Reports the Down reason for this ASCU if it is down.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), noReason(2), notDown(3), ascuDisabled(4), errorThresholdExceeded(5)

alpsAscuOutPackets		1.3.6.1.4.1.9.9.95.1.5.1.1.11
Number of packets transmitted to this ASCU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsAscuOutOctets		1.3.6.1.4.1.9.9.95.1.5.1.1.12
Number of octets transmitted to this ASCU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsAscuInPackets		1.3.6.1.4.1.9.9.95.1.5.1.1.13
Number of packets received from this ASCU
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsAscuInOctets		1.3.6.1.4.1.9.9.95.1.5.1.1.14
Number of octets received from this ASCU.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsAscuDropsGarbledPkts		1.3.6.1.4.1.9.9.95.1.5.1.1.15
The number of packets dropped due to the inability to properly decode them. Examples of garbled packets include packets with bad CRCs or bad header information
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsAscuDropsAscuDown		1.3.6.1.4.1.9.9.95.1.5.1.1.16
The number of packets dropped because the ASCU had previously been declared DOWN due to error thresholds being exceeded.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsAscuDropsAscuDisabled		1.3.6.1.4.1.9.9.95.1.5.1.1.17
The number of packets dropped because the ASCU had previously been declared to be in disabled state.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

alpsAscuEnabled		1.3.6.1.4.1.9.9.95.1.5.1.1.18
Specifies whether the ASCU has been enabled or not. After the ASCU has been configured, it must be explicitly enabled to allow it to be polled.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alpsAscuRowStatus		1.3.6.1.4.1.9.9.95.1.5.1.1.19
This object is used to create a new row or modify or delete an existing row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alpsAscuAutoReset		1.3.6.1.4.1.9.9.95.1.5.1.1.20
Specifies whether a reset command will be automatically issued to any non-responsive ALC ASCUs.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

alpsSvcMsgTable		1.3.6.1.4.1.9.9.95.1.6.1
A list of service messages and its associated number. There is a default list of service messages (list 0) as well as user-configurable service messages. On a per-circuit basis, the service message list to use can be selected. The user-configured service message lists are defined in this table. Note that the default service messages are not part of this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsSvcMsgEntry

alpsSvcMsgEntry		1.3.6.1.4.1.9.9.95.1.6.1.1
Service Messages configured along with its List number and Service Message Number in that list.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsSvcMsgEntry

alpsSvcMsgListNum		1.3.6.1.4.1.9.9.95.1.6.1.1.1
Specifies the Service Msg Number of this Service Msg. A maximum of 8 Service Message lists can be configured not including the one for Default/System (when alpsSvcMsgListNum = 0) Service messages.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..8

alpsSvcMsgNum		1.3.6.1.4.1.9.9.95.1.6.1.1.2
Specifies the Service Msg Number of this Service Msg. A Maximum of 8 messages can be present.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..8

alpsSvcMsg		1.3.6.1.4.1.9.9.95.1.6.1.1.3
Specifies the Service Message string .
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..50)

alpsSvcMsgRowStatus		1.3.6.1.4.1.9.9.95.1.6.1.1.4
This object is used to create a new row or modify or delete an existing row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

alpsX121ToIpTransTable		1.3.6.1.4.1.9.9.95.1.6.2
A Translation table between X.121 address and IP address. This is intended to allow a connection to be established to the appropriate remote router. The X121 address in the call packet is used to look up the IP address of the remote peer
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AlpsX121ToIpTransEntry

alpsX121ToIpTransEntry		1.3.6.1.4.1.9.9.95.1.6.2.1
A mapping table between X.121 address and IP address.
Status: current	Access: not-accessible
OBJECT-TYPE
	AlpsX121ToIpTransEntry

alpsX121		1.3.6.1.4.1.9.9.95.1.6.2.1.1
Specfies the X.121 address of the VC established with EMTOX host.
Status: current	Access: not-accessible
OBJECT-TYPE
	X121Address

alpsIpAddress		1.3.6.1.4.1.9.9.95.1.6.2.1.2
This is the IP address of the remote peer which maps onto the X.121 address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

alpsX121ToIpTransRowStatus		1.3.6.1.4.1.9.9.95.1.6.2.1.3
This object is used to create a new row or modify or delete an existing row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

ciscoAlpsMIBNotificationPrefix		1.3.6.1.4.1.9.9.95.2
OBJECT IDENTIFIER

ciscoAlpsMIBNotifications		1.3.6.1.4.1.9.9.95.2.0
OBJECT IDENTIFIER

alpsPeerStatusChange		1.3.6.1.4.1.9.9.95.2.0.1
This Notification is generated when there is a change in state for the peer connection, provided alarms are enabled for that peer.
Status: deprecated	Access: read-create
NOTIFICATION-TYPE

alpsCktStatusChange		1.3.6.1.4.1.9.9.95.2.0.2
This Notification has to be generated whenever there is a state change for the ALPS circuit, provided alarms are enabled for that circuit
Status: current	Access: read-create
NOTIFICATION-TYPE

alpsAscuStatusChange		1.3.6.1.4.1.9.9.95.2.0.3
This Notification has to be generated whenever there is a change in ASCU status, provided alarms are enabled for that ASCU
Status: current	Access: read-create
NOTIFICATION-TYPE

alpsPeerConnStatusChange		1.3.6.1.4.1.9.9.95.2.0.4
This Notification is generated when there is a change in state for an ALPS peer connection, provided alarms are enabled for that peer connection.
Status: current	Access: read-create
NOTIFICATION-TYPE

alpsCktOpenFailure		1.3.6.1.4.1.9.9.95.2.0.5
This Notification is generated whenever there is an open failure for the ALPS circuit, provided alarms are enabled for that circuit
Status: current	Access: read-create
NOTIFICATION-TYPE

alpsCktPartialReject		1.3.6.1.4.1.9.9.95.2.0.6
This Notification is generated whenever there is an open confirmation that contains a list of rejected ASCUs for the ALPS circuit, provided alarms are enabled for that circuit
Status: current	Access: read-create
NOTIFICATION-TYPE

alpsMibConformance		1.3.6.1.4.1.9.9.95.3
OBJECT IDENTIFIER

alpsMibCompliances		1.3.6.1.4.1.9.9.95.3.1
OBJECT IDENTIFIER

alpsMibGroups		1.3.6.1.4.1.9.9.95.3.2
OBJECT IDENTIFIER

alpsMibCompliance		1.3.6.1.4.1.9.9.95.3.1.1
The compliance statement for ALPS.
Status: deprecated	Access: read-create
MODULE-COMPLIANCE

alpsMibComplianceRev1		1.3.6.1.4.1.9.9.95.3.1.2
The compliance statement for ALPS.
Status: deprecated	Access: read-create
MODULE-COMPLIANCE

alpsMibComplianceRev2		1.3.6.1.4.1.9.9.95.3.1.3
The compliance statement for ALPS.
Status: current	Access: read-create
MODULE-COMPLIANCE

alpsPeerGroup		1.3.6.1.4.1.9.9.95.3.2.1
A collection of objects providing Peer information
Status: deprecated	Access: read-create
OBJECT-GROUP

alpsCktGroup		1.3.6.1.4.1.9.9.95.3.2.2
A collection of objects providing Circuit information
Status: current	Access: read-create
OBJECT-GROUP

alpsIfP1024Group		1.3.6.1.4.1.9.9.95.3.2.3
A collection of objects providing ALC interface information
Status: deprecated	Access: read-create
OBJECT-GROUP

alpsIfHostlinkGroup		1.3.6.1.4.1.9.9.95.3.2.4
A collection of objects providing Hostlink information
Status: current	Access: read-create
OBJECT-GROUP

alpsAscuGroup		1.3.6.1.4.1.9.9.95.3.2.5
A collection of objects providing ASCU information
Status: deprecated	Access: read-create
OBJECT-GROUP

alpsSvcMsgGroup		1.3.6.1.4.1.9.9.95.3.2.6
A collection of objects providing Service Message information
Status: current	Access: read-create
OBJECT-GROUP

alpsAddrTransGroup		1.3.6.1.4.1.9.9.95.3.2.7
A collection of objects providing Address Translation information.
Status: current	Access: read-create
OBJECT-GROUP

alpsPeerGroupRev1		1.3.6.1.4.1.9.9.95.3.2.9
A collection of objects providing peer information.
Status: current	Access: read-create
OBJECT-GROUP

alpsIfP1024GroupRev1		1.3.6.1.4.1.9.9.95.3.2.11
A collection of objects providing ALC interface information
Status: current	Access: read-create
OBJECT-GROUP

alpsAscuGroupRev1		1.3.6.1.4.1.9.9.95.3.2.12
A collection of objects providing ASCU information
Status: current	Access: read-create
OBJECT-GROUP

alpsNotificationGroup		1.3.6.1.4.1.9.9.95.3.2.8
A collection of notifications.
Status: obsolete	Access: read-create
NOTIFICATION-GROUP

alpsNotificationGroupRev1		1.3.6.1.4.1.9.9.95.3.2.10
A collection of notifications.
Status: deprecated	Access: read-create
NOTIFICATION-GROUP

alpsNotificationGroupRev2		1.3.6.1.4.1.9.9.95.3.2.13
A collection of notifications.
Status: current	Access: read-create
NOTIFICATION-GROUP