CAMBIUM-PTP500-MIB

File: CAMBIUM-PTP500-MIB.mib (91758 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Integer32 IpAddress enterprises
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
DisplayString

Defined Types

DfsTableEntry  
SEQUENCE    
  dfsTableIndex INTEGER
  dfsMeans Integer32
  dfsNineNinePointNinePercentiles Integer32
  dfsPeaks Integer32

VLANPriorityTableEntry  
SEQUENCE    
  vLANPriorityQueueMapping INTEGER
  vLANPriorityTableIndex INTEGER

SNMPTrapTableEntry  
SEQUENCE    
  sNMPTrapTableIndex INTEGER
  sNMPTrapIPAddress IpAddress
  sNMPTrapPortNumber INTEGER

UserTableEntry  
SEQUENCE    
  userTableIndex INTEGER
  userName OCTET STRING
  userRole INTEGER
  userEnabled INTEGER
  userPassword OCTET STRING

Defined Values

cambium 1.3.6.1.4.1.17713
MIB for 105Mbps non-line-of-sight (NLOS) wireless ethernet bridge.
MODULE-IDENTITY    

ptp 1.3.6.1.4.1.17713.1
OBJECT IDENTIFIER    

ptmp 1.3.6.1.4.1.17713.2
OBJECT IDENTIFIER    

ptp500 1.3.6.1.4.1.17713.5
OBJECT IDENTIFIER    

dfs 1.3.6.1.4.1.17713.5.3
OBJECT IDENTIFIER    

configuration 1.3.6.1.4.1.17713.5.5
OBJECT IDENTIFIER    

ethernet 1.3.6.1.4.1.17713.5.6
OBJECT IDENTIFIER    

telecom 1.3.6.1.4.1.17713.5.7
OBJECT IDENTIFIER    

licence 1.3.6.1.4.1.17713.5.8
OBJECT IDENTIFIER    

management 1.3.6.1.4.1.17713.5.9
OBJECT IDENTIFIER    

phyControl 1.3.6.1.4.1.17713.5.10
OBJECT IDENTIFIER    

phyStatus 1.3.6.1.4.1.17713.5.12
OBJECT IDENTIFIER    

alarms 1.3.6.1.4.1.17713.5.13
OBJECT IDENTIFIER    

smtp 1.3.6.1.4.1.17713.5.15
OBJECT IDENTIFIER    

snmpControl 1.3.6.1.4.1.17713.5.16
OBJECT IDENTIFIER    

sntp 1.3.6.1.4.1.17713.5.17
OBJECT IDENTIFIER    

reset 1.3.6.1.4.1.17713.5.18
OBJECT IDENTIFIER    

versions 1.3.6.1.4.1.17713.5.19
OBJECT IDENTIFIER    

pubStats 1.3.6.1.4.1.17713.5.20
OBJECT IDENTIFIER    

encryption 1.3.6.1.4.1.17713.5.22
OBJECT IDENTIFIER    

tDDControl 1.3.6.1.4.1.17713.5.23
OBJECT IDENTIFIER    

aAAControl 1.3.6.1.4.1.17713.5.25
OBJECT IDENTIFIER    

syslogControl 1.3.6.1.4.1.17713.5.24
OBJECT IDENTIFIER    

supplementary 1.3.6.1.4.1.17713.5.96
OBJECT IDENTIFIER    

ptpGroups 1.3.6.1.4.1.17713.5.98
OBJECT IDENTIFIER    

ptpTraps 1.3.6.1.4.1.17713.5.99
OBJECT IDENTIFIER    

ptpTrapPrefix 1.3.6.1.4.1.17713.5.99.0
OBJECT IDENTIFIER    

ptpCompliance 1.3.6.1.4.1.17713.5.97
The compliance statement for the Cambium PTP MIB
Status: current Access: read-only
MODULE-COMPLIANCE    

dfsGroup 1.3.6.1.4.1.17713.5.98.3
The dfs object group.
Status: current Access: read-only
OBJECT-GROUP    

configurationGroup 1.3.6.1.4.1.17713.5.98.5
The configuration object group.
Status: current Access: read-only
OBJECT-GROUP    

ethernetGroup 1.3.6.1.4.1.17713.5.98.6
The ethernet object group.
Status: current Access: read-only
OBJECT-GROUP    

telecomGroup 1.3.6.1.4.1.17713.5.98.7
The telecom object group.
Status: current Access: read-only
OBJECT-GROUP    

licenceGroup 1.3.6.1.4.1.17713.5.98.8
The licence object group.
Status: current Access: read-only
OBJECT-GROUP    

managementGroup 1.3.6.1.4.1.17713.5.98.9
The management object group.
Status: current Access: read-only
OBJECT-GROUP    

phyControlGroup 1.3.6.1.4.1.17713.5.98.10
The phyControl object group.
Status: current Access: read-only
OBJECT-GROUP    

phyStatusGroup 1.3.6.1.4.1.17713.5.98.12
The phyStatus object group.
Status: current Access: read-only
OBJECT-GROUP    

alarmsGroup 1.3.6.1.4.1.17713.5.98.13
The alarms object group.
Status: current Access: read-only
OBJECT-GROUP    

smtpGroup 1.3.6.1.4.1.17713.5.98.15
The smtp object group.
Status: current Access: read-only
OBJECT-GROUP    

snmpControlGroup 1.3.6.1.4.1.17713.5.98.16
The snmpControl object group.
Status: current Access: read-only
OBJECT-GROUP    

sntpGroup 1.3.6.1.4.1.17713.5.98.17
The sntp object group.
Status: current Access: read-only
OBJECT-GROUP    

resetGroup 1.3.6.1.4.1.17713.5.98.18
The reset object group.
Status: current Access: read-only
OBJECT-GROUP    

versionsGroup 1.3.6.1.4.1.17713.5.98.19
The versions object group.
Status: current Access: read-only
OBJECT-GROUP    

pubStatsGroup 1.3.6.1.4.1.17713.5.98.20
The pubStats object group.
Status: current Access: read-only
OBJECT-GROUP    

encryptionGroup 1.3.6.1.4.1.17713.5.98.22
The encryption object group.
Status: current Access: read-only
OBJECT-GROUP    

tDDControlGroup 1.3.6.1.4.1.17713.5.98.23
The tDDControl object group.
Status: current Access: read-only
OBJECT-GROUP    

aAAControlGroup 1.3.6.1.4.1.17713.5.98.25
The aAAControl object group.
Status: current Access: read-only
OBJECT-GROUP    

syslogControlGroup 1.3.6.1.4.1.17713.5.98.24
The syslogControl object group.
Status: current Access: read-only
OBJECT-GROUP    

supplementaryGroup 1.3.6.1.4.1.17713.5.98.96
The supplementary object group.
Status: current Access: read-only
OBJECT-GROUP    

notificationsGroup 1.3.6.1.4.1.17713.5.98.99
The notifications group.
Status: current Access: read-only
NOTIFICATION-GROUP    

dfsTable 1.3.6.1.4.1.17713.5.3.2
A table storing a snapshot of various DFS measurements for each channel
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DfsTableEntry

dfsTableEntry 1.3.6.1.4.1.17713.5.3.2.1
Table DfsTable
Status: current Access: not-accessible
OBJECT-TYPE    
  DfsTableEntry  

vLANPriorityTable 1.3.6.1.4.1.17713.5.6.15
A priority queue mapping table. This is a list of packet queues indexed by VLAN priority.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VLANPriorityTableEntry

vLANPriorityTableEntry 1.3.6.1.4.1.17713.5.6.15.1
Table VLANPriorityTable
Status: current Access: not-accessible
OBJECT-TYPE    
  VLANPriorityTableEntry  

sNMPTrapTable 1.3.6.1.4.1.17713.5.16.4
SNMP trap configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SNMPTrapTableEntry

sNMPTrapTableEntry 1.3.6.1.4.1.17713.5.16.4.1
Table SNMPTrapTable
Status: current Access: not-accessible
OBJECT-TYPE    
  SNMPTrapTableEntry  

userTable 1.3.6.1.4.1.17713.5.25.2
The User Table Control group contains objects specifically for user account management.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UserTableEntry

userTableEntry 1.3.6.1.4.1.17713.5.25.2.1
Table UserTable
Status: current Access: not-accessible
OBJECT-TYPE    
  UserTableEntry  

dfsTableNumber 1.3.6.1.4.1.17713.5.3.1
Number of entries in the dfsTable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..63  

dfsTableIndex 1.3.6.1.4.1.17713.5.3.2.1.1
used to index values in the dfsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..63  

dfsMeans 1.3.6.1.4.1.17713.5.3.2.1.2
Snapshot of DFS means
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dfsNineNinePointNinePercentiles 1.3.6.1.4.1.17713.5.3.2.1.3
Snapshot of DFS 99.9 percentiles
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dfsPeaks 1.3.6.1.4.1.17713.5.3.2.1.4
Snapshot of DFS peaks
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

iPAddress 1.3.6.1.4.1.17713.5.5.1
Internet protocol (IP) address. This address is used by the family of Internet protocols to uniquely identify the unit on a network. NB: A system reboot is required to activate changes to this attribute.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

subnetMask 1.3.6.1.4.1.17713.5.5.2
A subnet allows the flow of network traffic between hosts to be segregated based on a network configuration. By organizing hosts into logical groups, subnetting can improve network security and performance. NB: A system reboot is required to activate changes to this attribute
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

gatewayIPAddress 1.3.6.1.4.1.17713.5.5.3
The IP address of a computer on the current network that is currently acting as a network gateway. A gateway acts as an entrance / exit to packets from / to other networks. NB: A system reboot is required to activate changes to this attribute
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

targetMACAddress 1.3.6.1.4.1.17713.5.5.4
MAC address of the PTP wireless unit forming the other end of the PTP link
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

masterSlaveMode 1.3.6.1.4.1.17713.5.5.5
The PTP wireless link operates using a master and slave relationship
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER master(0), slave(1)  

maximumTransmitPower 1.3.6.1.4.1.17713.5.5.6
Maximum transmit power the wireless unit is permitted to use when establishing and maintaining the wireless link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -100..27  

antennaGain 1.3.6.1.4.1.17713.5.5.7
Antenna Gain. Expressed in 10ths of dBi. NB: This attribute is ignored for variants with an integral antenna.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..610  

cableLoss 1.3.6.1.4.1.17713.5.5.8
Loss in the cable between the ODU and the antenna. Expressed in 10ths of dB. NB: This attribute is ignored for variants with an integral antenna.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

eIRP 1.3.6.1.4.1.17713.5.5.9
Effective Isotropic Radiated Power (EIRP) describes the strength of the radio signal leaving the wireless unit. Expressed in 10ths of dBm
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

channelBandwidth 1.3.6.1.4.1.17713.5.5.11
This control sets the bandwidth of the transmit and receive radio channels
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER bw30MHz(0), bw15MHz(1), bw10MHz(2), bw5MHz(3), bw20MHz(4)  

remoteIPAddress 1.3.6.1.4.1.17713.5.5.12
IP Address of the peer wireless unit
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

linkName 1.3.6.1.4.1.17713.5.5.14
Name of the PTP link allocated by the System Administrator. Used to establish a connection with the correct PTP wireless unit at the other end of the link. NOTE: The link name MUST be the same at both ends of the PTP link.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

siteName 1.3.6.1.4.1.17713.5.5.15
This field contains a user-provided description of the site name together with any additional notes
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

accessMethod 1.3.6.1.4.1.17713.5.5.16
This controls whether the link can be established between pre-paired Master-Slave using MAC addresses (Link Access) or by using link name (Link Name Access)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER linkAccess(0), linkNameAccess(1), groupAccess(2)  

groupID 1.3.6.1.4.1.17713.5.5.17
When Access Method is set to Group Access, the Group ID identifies all the units belonging to the same group. Group Access is only supported on some platforms
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

dataPortAutoNegotiation 1.3.6.1.4.1.17713.5.6.1
This controls whether the local Ethernet interface configuration is automatically negotiated or forced. Do not use a forced setting together with auto negotiation at the Ethernet link partner. If you want to run your Ethernet link at a fixed speed and duplex then you would normally leave auto negotiation enabled and only enable the single Auto Neg Advertisement option that you want the link to run in - FORCING ETHERNET CONFIGURATION IS A LAST RESORT WHICH SHOULD ONLY BE PERFORMED IF YOU ARE HAVING PROBLEMS WITH AUTO NEGOTIATION - AND YOU MUST ENSURE THAT YOU CONFIGURE BOTH THIS UNIT AND THE ETHERNET LINK PARTNER TO WHICH IT IS CONNECTED IDENTICALLY (THE LINK PARTNER MUST NOT HAVE AUTO NEGOTIATION ENABLED EITHER, OTHERWISE A DUPLEX MISMATCH WILL OCCUR). NB: The new setting will only take effect after a system reboot.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dataPortAutoNegAdvertisement 1.3.6.1.4.1.17713.5.6.2
This sets the different Ethernet configurations that will be advertised during auto negotiation. NB: The new setting will only take effect after a system reboot. WARNING: Duplex mismatch may result if both ends of the Ethernet link do not have the same settings. Do not auto negotiation together with a fixed setting at the Ethernet link partner. WARNING: Make sure that you select option(s) that you know your connected equipment can cater for!
Status: current Access: read-write
OBJECT-TYPE    
  BITS negInvalid(2), neg10MbpsHalfDuplex(3), neg10MbpsFullDuplex(4), neg100MbpsHalfDuplex(5), neg100MbpsFullDuplex(6), negUnknown1(7)  

dataPortAutoMdix 1.3.6.1.4.1.17713.5.6.3
This enables/disables the Auto MDI/MDIX capability. NB: The new setting will only take effect after a system reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dataPortStatus 1.3.6.1.4.1.17713.5.6.4
Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(0), copperLinkUp(1), fiberLinkUp(2)  

dataPortSpeedAndDuplex 1.3.6.1.4.1.17713.5.6.5
The current speed and duplex of the Ethernet link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER speed1000MbpsFullDuplex(0), speed100MbpsFullDuplex(1), speed100MbpsHalfDuplex(2), speed10MbpsFullDuplex(3), speed10MbpsHalfDuplex(4), speedUnknown6(5)  

dataPortWirelessDownAlert 1.3.6.1.4.1.17713.5.6.6
When enabled, this causes the Ethernet link to be dropped briefly when the wireless link drops. This is so that spanning tree algorithms can quickly detect that there is a problem.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

useVLANForManagementInterfaces 1.3.6.1.4.1.17713.5.6.7
This controls whether the management interfaces (WWW/SNMP/SMTP/SNTP) use VLAN tags or not. NB: The new setting will only take effect after a system reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noVLANTagging(0), iEEE8021QTaggedCTagType8100(1), iEEE8021adTaggedSTagorBTagType88a8(2)  

vLANManagementPriority 1.3.6.1.4.1.17713.5.6.8
This VLAN Priority (0-7) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

vLANManagementVID 1.3.6.1.4.1.17713.5.6.11
This VLAN VID (0-4094) will be included in packets generated by the management interfaces. NB: The new setting will only take effect after a system reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4094  

vLANPriorityTableNumber 1.3.6.1.4.1.17713.5.6.14
Number of entries in the vLANPriorityTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 9  

vLANPriorityQueueMapping 1.3.6.1.4.1.17713.5.6.15.1.1
Mapping of VLAN priority flag to packet queue. The higher the queue number the greater its priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER q0(0), q1(1), q2(2), q3(3), q4(4), q5(5), q6(6), q7(7)  

vLANPriorityTableIndex 1.3.6.1.4.1.17713.5.6.15.1.2
VLAN priority flag, used to index values in the vLANPriorityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER p0(1), p1(2), p2(3), p3(4), p4(5), p5(6), p6(7), p7(8), untagged(9)  

telecomsInterface 1.3.6.1.4.1.17713.5.7.1
The line interface type. If this is set to 'None' then the telecoms interfaces are disabled, and the telecom group attributes will be ignored.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), e1(1), t1(2)  

telecomsChannelStatus 1.3.6.1.4.1.17713.5.7.2
Current status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), noSignalLocal(1), noSignalRemote(2), noSignalLocalandRemote(3), up(4), remoteTiming(5), noSignalLocalandRemoteTiming(6)  

telecomsLineCode 1.3.6.1.4.1.17713.5.7.4
The line code setting of the telecoms interface. This must match the setting of the device connected to this interface
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER aMI(0), b8ZSHDB3(1)  

telecomsCableLength 1.3.6.1.4.1.17713.5.7.6
The length of the cable connected to the telecoms interface, measured in feet
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER feet133(0), feet266(1), feet399(2), feet533(3), feet655(4)  

telecomsLoopback 1.3.6.1.4.1.17713.5.7.8
The loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. When applying a wireless loopback, please ensure that the other end of the link has a loopback setting of 'None'. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), copper(1), wireless(2)  

regionCode 1.3.6.1.4.1.17713.5.8.1
The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER regionCodeInvalid(0), regionCode1(1), regionCode2(2), regionCode3(3), regionCode4(4), regionCode5(5), regionCode6(6), regionCode7(7), regionCode8(8), regionCode9(9), regionCode10(10), regionCode11(11), regionCode12(12), regionCode13(13), regionCode14(14), regionCode15(15), regionCode16(16), regionCode17(17), regionCode18(18), regionCode19(19), regionCode20(20), regionCode21(21), regionCode22(22), regionCode23(23), regionCode24(24), regionCode25(25), regionCode26(26), regionCode27(27), regionCode28(28), regionCode29(29), regionCode30(30), regionCode31(31)  

productVariant 1.3.6.1.4.1.17713.5.8.2
The product variant
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER pTPxx400Full(0), pTPxx400Deprecated1(1), pTPxx400Deprecated2(2), pTPxx400Lite(3), spare1(4), pTPxx300(5), spare2(6), spare3(7), pTPxx500FullDeprecated(8), pTPxx500LiteDeprecated(9), pTPxx500(10), pTPxx600Lite(11), pTPxx600Full(12), spare5(13), spare6(14), pTP800(15)  

productName 1.3.6.1.4.1.17713.5.8.3
Name of the product variant
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

ethernetFiberSupport 1.3.6.1.4.1.17713.5.8.4
Ethernet fiber support availability on this wireless unit
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

frequencyVariant 1.3.6.1.4.1.17713.5.8.5
Frequency variant of the wireless unit
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER freq5800MHz(0), freq5400MHz(1), freq4900MHz(2), freq2500MHz(3), freq5800MHz2(4), freq5400MHz2(5), freq4500MHz(6), freq5900MHz(7), freq5200MHz(8), freq5100MHz(9), freq4800MHz(10)  

bandwidthVariant 1.3.6.1.4.1.17713.5.8.6
Bandwidth variant of the wireless unit
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER bw30MHz(0), bw15MHz(1), bw10MHz(2), bw5MHz(3), bw20MHz(4)  

constantPowerSpectralDensity 1.3.6.1.4.1.17713.5.8.7
Constant power spectral density mode control
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER constant(0), fullPower(1)  

sNMPv3Enable 1.3.6.1.4.1.17713.5.8.9
SNMPv3 availability control
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

licensedCapacity 1.3.6.1.4.1.17713.5.8.11
Maximum allowable data rate for ethernet frames permitted by the licence key. The actual data rate depends upon the prevailing wireless conditions
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER capacity25Mbps(0), capacity52Mbps(1), capacity105Mbps(2)  

installStatus 1.3.6.1.4.1.17713.5.9.3
A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), wrongPeer(1)  

installArmState 1.3.6.1.4.1.17713.5.9.4
Indicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disarmed(0), armed(1)  

tFTPServerIPAddress 1.3.6.1.4.1.17713.5.9.5
IP address of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

tFTPServerPortNumber 1.3.6.1.4.1.17713.5.9.6
The port number of the TFTP Server from which the TFTP Software Upgrade File Name will be retrieved
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

tFTPSoftwareUpgradeFileName 1.3.6.1.4.1.17713.5.9.7
Filename of the Software Upgrade to be loaded from the TFTP Server
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

tFTPStartSoftwareUpgrade 1.3.6.1.4.1.17713.5.9.8
Write '1' to this attribute to start the TFTP software upgrade process. The attribute will be reset to 0 when the upgrade process has finished
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

tFTPSoftwareUpgradeStatus 1.3.6.1.4.1.17713.5.9.9
The current status of the TFTP Software upgrade process
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), uploadinprogress(1), uploadsuccessfulprogrammingFLASH(2), upgradesuccessfulreboottorunthenewsoftwareimage(3), upgradefailed(4)  

tFTPSoftwareUpgradeStatusText 1.3.6.1.4.1.17713.5.9.10
Descriptive text describing the status of the TFTP Software upgrade process, including any error details
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

tFTPSoftwareUpgradeStatusAdditionalText 1.3.6.1.4.1.17713.5.9.11
Any additional text describing the status of the TFTP Software upgrade process, including any error details
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

hTTPAccessEnabled 1.3.6.1.4.1.17713.5.9.12
This controls whether or not HTTP access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTP port. Remote management via HTTPS is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

telnetAccessEnabled 1.3.6.1.4.1.17713.5.9.13
This controls whether or not Telnet access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the TELNET port. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Disabled)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

hTTPPortNumber 1.3.6.1.4.1.17713.5.9.14
This controls the port number for HTTP access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 80)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

hTTPSPortNumber 1.3.6.1.4.1.17713.5.9.15
This controls the port number for HTTPS access. A value of zero will use the default port number. Availability of HTTPS is controlled via the Licence Key. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 443)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

telnetPortNumber 1.3.6.1.4.1.17713.5.9.16
This controls the port number for TELNET access. A value of zero will use the default port number. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = 23)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

hTTPSAccessEnabled 1.3.6.1.4.1.17713.5.9.17
This controls whether or not HTTPS access is enabled, i.e. if this is disabled (0) then the unit will not respond to any requests on the HTTPS port. Remote management via HTTP is not affected by this setting. Any change in this setting will not take effect until the unit has been rebooted. (Factory default = Enabled)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

linkSymmetry 1.3.6.1.4.1.17713.5.10.1
In fixed asymmetric mode (3 to 1) the transmit time is three times as long as the receive time. In fixed symmetric mode (1 to 1) the unit spends an equal amount of time transmitting and receiving. In fixed asymmetric mode (1 to 3) the receive time is three times as long as the transmit time. In adaptive mode the transmit and receive periods adjust with applied load. NB: only applicable for master nodes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER symmetryAdaptive(0), symmetry3to1(1), symmetry1to1(2), symmetry1to3(3)  

linkModeOptimisation 1.3.6.1.4.1.17713.5.10.2
Optimises the wireless link behavior for the type of traffic to be carried. In 'IP Traffic' mode, the wireless link will minimise transmission errors by automatically adapting the modulation mode. In 'TDM Traffic' mode, the wireless link will minimise transmission latency and preserve throughput by maintaining a higher modulation mode in the presence of a limited number of errors. The 'TDM Traffic' mode is recommended for E1/T1 applications and connectionless protocols.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER iPTraffic(0), tDMTraffic(1)  

userConfiguredMaxModulationMode 1.3.6.1.4.1.17713.5.10.3
The maximum receive modulation mode controls the MAX mode used for adaptive modulation. NOTE: This attribute is automatically disabled when the installation agent is armed. To disarm the installation agent use the installation wizard
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER modBpsk50percent(0), modQpsk50percent(1), modQpsk75percent(2), mod16qam50percent(3), mod16qam75percent(4), mod64qam67percent(5), mod64qam83percent(6)  

remoteMaximumTransmitPower 1.3.6.1.4.1.17713.5.10.4
Maximum transmit power the remote wireless unit is permitted to use when establishing and maintaining the wireless link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -100..27  

receivePower 1.3.6.1.4.1.17713.5.12.1
Receive power expressed in tenths of a dBm
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vectorError 1.3.6.1.4.1.17713.5.12.2
The vector error measurement compares the received signal's IQ modulation characteristics to an ideal signal to determine the composite error vector magnitude. The value represented by this attribute is the average vector error over the previous second expressed in tenths of a dB
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

transmitPower 1.3.6.1.4.1.17713.5.12.3
Transmit power expressed in tenths of a dBm
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

range 1.3.6.1.4.1.17713.5.12.4
Distance between the two peer wireless units expressed in tenths of a kilometer
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

linkLoss 1.3.6.1.4.1.17713.5.12.5
The wireless link loss expressed in tenths of a dB
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -500..500  

receiveChannel 1.3.6.1.4.1.17713.5.12.6
Current active receive channel
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..63  

transmitChannel 1.3.6.1.4.1.17713.5.12.7
Current active transmit channel
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..63  

receiveModulationMode 1.3.6.1.4.1.17713.5.12.8
Current active receive modulation mode
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER modAcquisition(0), modBpsk50percent(1), modQpsk50percentSingle(2), modQpsk75percentSingle(3), mod16qam50percentSingle(4), mod16qam75percentSingle(5), mod64qam67percentSingle(6), mod64qam83percentSingle(7), modReserved1(8), modQpsk50percentDual(9), modQpsk75percentDual(10), mod16qam50percentDual(11), mod16qam75percentDual(12), mod64qam67percentDual(13), mod64qam83percentDual(14), modReserved2(15)  

transmitModulationMode 1.3.6.1.4.1.17713.5.12.9
Current active transmit modulation mode
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER modAcquisition(0), modBpsk50percent(1), modQpsk50percentSingle(2), modQpsk75percentSingle(3), mod16qam50percentSingle(4), mod16qam75percentSingle(5), mod64qam67percentSingle(6), mod64qam83percentSingle(7), modReserved1(8), modQpsk50percentDual(9), modQpsk75percentDual(10), mod16qam50percentDual(11), mod16qam75percentDual(12), mod64qam67percentDual(13), mod64qam83percentDual(14), modReserved2(15)  

receiveFreqMHz 1.3.6.1.4.1.17713.5.12.11
Current receive frequency expressed in integer MHz
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..5925  

transmitFreqMHz 1.3.6.1.4.1.17713.5.12.12
Current transmit frequency expressed in integer MHz
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..5925  

signalStrengthRatio 1.3.6.1.4.1.17713.5.12.13
Signal strength ratio (Vertical / Horizontal) : the number of dB larger the Vertical antenna input is than the Horizontal antenna input expressed in tenths of a dB
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

receiveFreqKHz 1.3.6.1.4.1.17713.5.12.14
Current receive frequency expressed as KHz
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..5925000  

transmitFreqKHz 1.3.6.1.4.1.17713.5.12.15
Current transmit frequency expressed as KHz
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..5925000  

searchState 1.3.6.1.4.1.17713.5.12.16
Search status of the wireless modem. 'Registering' means that the modem has locked to an OFDM signal, and the wireless link is up. 'Searching' means that no wireless signal has been detected. 'Acquiring' means that a wireless signal has been detected, but the modem has not locked to an OFDM signal.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER registering(0), searching(1), acquiring(2), registeringAcquiring2(3)  

unitOutOfCalibration 1.3.6.1.4.1.17713.5.13.1
The unit is out of calibration
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER calibrated(0), partialCalibration(1), invalidCalibration(2), bandwidthvariantunsupportedPAsShutdown(3), outOfCalibrationPAsShutdown(4)  

incompatibleRegionCodes 1.3.6.1.4.1.17713.5.13.4
The master and slave units have incompatible region codes. NB: Both units must have compatible licence keys
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), incompatibleLicenceKeys(1)  

noWirelessChannelAvailable 1.3.6.1.4.1.17713.5.13.5
Spectrum Management was unable to locate a suitable wireless channel to operate on
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), noWirelessChannelAvailable(1)  

wirelessLinkDisabledWarning 1.3.6.1.4.1.17713.5.13.6
The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), disabledBySNMPifAdminStatus(1)  

dataPortDisabledWarning 1.3.6.1.4.1.17713.5.13.7
The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), disabledBySNMPifAdminStatus(1)  

dataPortConfigurationMismatch 1.3.6.1.4.1.17713.5.13.9
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(0), mismatchDetected(1)  

incompatibleMasterAndSlave 1.3.6.1.4.1.17713.5.13.10
A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), incompatibleProductVariants(1), differentSoftwareVersionsRunning(2)  

tDDSynchronizationStatus 1.3.6.1.4.1.17713.5.13.11
An alarm value (displayed in red) indicates that one of the following conditions has not been met (i) An external timing system is connected or internal timing has been configured. (ii) The timing system is providing a useable reference. (iii) The ODU is locked to this reference.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER locked(0), holdover(1), holdoverNotConnected(2), acquiringLock(3), noTimingReference(4), timingSystemNotConnected(5), initialising(6), clusterTimingMaster(7), tDDSyncNotActive(8)  

tDDSynchronizationAlarm 1.3.6.1.4.1.17713.5.13.13
Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), notSynchronized(1), timingSystemFailure(2)  

linkModeOptimizationMismatch 1.3.6.1.4.1.17713.5.13.14
The remote node of this link has been configured with a different link mode optimization
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), linkModeOptimizationMismatch(1)  

capacityLicenseMismatch 1.3.6.1.4.1.17713.5.13.16
The local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating at the capacity of the lowest capacity unit
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), mismatchDetected(1)  

sMTPEmailAlert 1.3.6.1.4.1.17713.5.15.1
Simple Mail Transfer Protocol is used to send equipment alerts via email to a specified email address. This utility can only be configured by the system administrator
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

sMTPServerIPAddress 1.3.6.1.4.1.17713.5.15.2
IP address of the SMTP server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sMTPServerPortNumber 1.3.6.1.4.1.17713.5.15.3
Port number of the SMTP server
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

sMTPSourceEmailAddress 1.3.6.1.4.1.17713.5.15.4
The 'from' email address used when constructing the automatically generated e-mail message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

sMTPDestinationEmailAddress 1.3.6.1.4.1.17713.5.15.5
The 'to' email address used when constructing the automatically generated e-mail message
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

sMTPEnabledMessages 1.3.6.1.4.1.17713.5.15.6
This controls which SMTP messages the unit will send
Status: current Access: read-write
OBJECT-TYPE    
  BITS telecomsChannelUpDown(1), unknown6(2), dataPortUpDown(3), enabledDiagnosticAlarms(4), dFSImpulseInterference(5), channelChange(6), wirelessLinkUpDown(7)  

sNMPPortNumber 1.3.6.1.4.1.17713.5.16.1
The IP port number used to access the SNMP MIB (i.e. Gets and Sets) (default = 161). NB: A system reboot is required to activate changes to this attribute
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

sNMPCommunityString 1.3.6.1.4.1.17713.5.16.2
The SNMP community string. NB: A system reboot is required to activate changes to this attribute
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

sNMPTrapTableNumber 1.3.6.1.4.1.17713.5.16.3
Number of entries in the sNMPTrapTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 2  

sNMPTrapVersion 1.3.6.1.4.1.17713.5.16.5
The SNMP protocol version to use for SNMP Traps. NB: A system reboot is required to activate changes to this attribute
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER v1(0), v2c(1)  

sNMPEnabledTraps 1.3.6.1.4.1.17713.5.16.6
This controls which SNMP Traps the unit will send
Status: current Access: read-write
OBJECT-TYPE    
  BITS unknown8(0), dataPortUpDown(1), authenticationFailure(2), enabledDiagnosticAlarms(3), dFSImpulseInterference(4), channelChange(5), wirelessLinkUpDown(6), coldStart(7), telecomsChannelUpDown(15)  

enabledDiagnosticAlarms 1.3.6.1.4.1.17713.5.16.7
Controls which individual diagnostic alarms are enabled. The unit may be configured to generate SNMP traps and/or SMTP email alerts for these enabled alarms by selecting 'Enabled Diagnostic Alarms' on the 'SNMP Enabled Traps' and/or 'SMTP Enabled Messages' attributes
Status: current Access: read-write
OBJECT-TYPE    
  BITS incompatibleMasterAndSlave(0), incompatibleRegionCodes(1), unknown6(2), unknown5(3), unitOutOfCalibration(4), installArmState(5), installStatus(6), regionCode(7), telecomsChannelStatus(8), unknown15(9), dataPortStatus(10), dataPortDisabledWarning(11), wirelessLinkDisabledWarning(12), sNTPSynchronizationFailed(13), noWirelessChannelAvailable(14), dataPortConfigurationMismatch(15), syslogClientDisabledWarning(16), licensedCapacityMismatch(17), syslogLocalWrapped(18), syslogLocalNearlyFull(19), syslogLocalEnableDisable(20), linkModeOptimizationMismatch(21), tDDSynchronizationAlarm(22), telecomsChannelLoopback(23)  

sNMPSendAllTrapsAtStartup 1.3.6.1.4.1.17713.5.16.8
Controls whether cleared traps are reported at start-up as well as raised traps. Only enabled traps will be reported. NB: Traps corresponding to transient events (i.e. not associated with an alarm or status value) are only sent when required and not at start-up.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

sNMPTrapTableIndex 1.3.6.1.4.1.17713.5.16.4.1.1
SNMP trap value, used to index the SNMPTrapTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..2  

sNMPTrapIPAddress 1.3.6.1.4.1.17713.5.16.4.1.2
The IP address to which all SNMP Traps are sent. An IP Address of 0.0.0.0 disables all TRAP generation. NB: A system reboot is required to activate changes to this attribute.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sNMPTrapPortNumber 1.3.6.1.4.1.17713.5.16.4.1.3
Destination port for SNMP Traps (default=162). A value of 0 will disable the trap receiver. NB: A system reboot is required to activate changes to this attribute.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

sNTPState 1.3.6.1.4.1.17713.5.17.1
SNTP control state
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

sNTPServerIPAddress 1.3.6.1.4.1.17713.5.17.2
The IP address of a valid SNTP server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sNTPServerPortNumber 1.3.6.1.4.1.17713.5.17.3
The IP port number of the SNTP server. Defaults to port 123.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

sNTPPollInterval 1.3.6.1.4.1.17713.5.17.4
The SNTP server polling interval
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 60..43200  

sNTPSync 1.3.6.1.4.1.17713.5.17.5
If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noSync(0), inSync(1)  

sNTPLastSync 1.3.6.1.4.1.17713.5.17.6
Last SNTP sync time
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

systemClock 1.3.6.1.4.1.17713.5.17.7
System clock presented as local time
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

timeZone 1.3.6.1.4.1.17713.5.17.8
Time zone offsets from Greenwich Mean Time (GMT)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER gmtMinus1200(0), gmtMinus1130(1), gmtMinus1100(2), gmtMinus1030(3), gmtMinus1000(4), gmtMinus0930(5), gmtMinus0900(6), gmtMinus0830(7), gmtMinus0800(8), gmtMinus0730(9), gmtMinus0700(10), gmtMinus0630(11), gmtMinus0600(12), gmtMinus0530(13), gmtMinus0500(14), gmtMinus0430(15), gmtMinus0400(16), gmtMinus0330(17), gmtMinus0300(18), gmtMinus0230(19), gmtMinus0200(20), gmtMinus0130(21), gmtMinus0100(22), gmtMinus0030(23), gmtZero(24), gmtPlus0030(25), gmtPlus0100(26), gmtPlus0130(27), gmtPlus0200(28), gmtPlus0230(29), gmtPlus0300(30), gmtPlus0330(31), gmtPlus0400(32), gmtPlus0430(33), gmtPlus0500(34), gmtPlus0530(35), gmtPlus0600(36), gmtPlus0630(37), gmtPlus0700(38), gmtPlus0730(39), gmtPlus0800(40), gmtPlus0830(41), gmtPlus0900(42), gmtPlus0930(43), gmtPlus1000(44), gmtPlus1030(45), gmtPlus1100(46), gmtPlus1130(47), gmtPlus1200(48), gmtPlus1230(49), gmtPlus1300(50)  

daylightSaving 1.3.6.1.4.1.17713.5.17.9
Daylight Saving Time
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

systemReset 1.3.6.1.4.1.17713.5.18.1
Setting this attribute to '1' will cause a system reboot. NB: a system reboot will apply any pending new settings held in memory
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER running(0), consoleReboot(1)  

softwareVersion 1.3.6.1.4.1.17713.5.19.1
Current software version
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

hardwareVersion 1.3.6.1.4.1.17713.5.19.2
Hardware platform version
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

secondarySoftwareVersion 1.3.6.1.4.1.17713.5.19.3
Secondary software version, used when the primary software image is invalid or erased
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

bootVersion 1.3.6.1.4.1.17713.5.19.4
Boot code software version
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

receiveDataRate 1.3.6.1.4.1.17713.5.20.1
Average data rate over the last one second interval (kbps)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

transmitDataRate 1.3.6.1.4.1.17713.5.20.2
Average data rate over the last one second interval (kbps)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

aggregateDataRate 1.3.6.1.4.1.17713.5.20.3
Average data rate over the last one second interval (kbps)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wirelessLinkAvailability 1.3.6.1.4.1.17713.5.20.4
Link availability calculated since the last reset of the system counters, as a percentage multiplied by 10000 to give four decimal places of precision
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000000  

wirelessLinkStatus 1.3.6.1.4.1.17713.5.20.5
Current status of the wireless link
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(0), registering(1), acquiring(2), searching(3), radarCAC(4), initialising(5)  

byteErrorRatio 1.3.6.1.4.1.17713.5.20.6
Reciprocal of the byte error ratio calculated since the last reset of the system counters
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

receiveModulationModeDetail 1.3.6.1.4.1.17713.5.20.7
The reason for the current receive modulation mode
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER runningAtMaximumReceiveMode(0), runningAtUserConfiguredMaxModulationMode(1), restrictedBecauseInstallationIsArmed(2), restrictedBecauseOfByteErrorsOnTheWirelessLink(3), restrictedBecauseTheLinkParametersAreUpdating(4), restrictedBecauseChannelChangeIsInProgress(5), restrictedDueToTheLowEthernetLinkSpeed(6), runningAtMaximumReceiveModeForChannelBandwidth(7), limitedByTheWirelessConditions(8)  

encryptionAlgorithm 1.3.6.1.4.1.17713.5.22.1
The Encryption Algorithm used by the wireless link. NB: A system reboot is required to activate changes to this attribute. NB: The same Encryption Algorithm must be configured at BOTH ends of the link for it to function correctly
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), aESRijndael(1), aES256bitRijndael(2)  

tDDSynchronizationMode 1.3.6.1.4.1.17713.5.23.1
TDD Synchronization Mode selection
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

userTableNumber 1.3.6.1.4.1.17713.5.25.1
Number of entries in the userTable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

userTableIndex 1.3.6.1.4.1.17713.5.25.2.1.1
used to index values in the userTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..10  

userName 1.3.6.1.4.1.17713.5.25.2.1.2
User name which must be entered, along with the appropriate password, in order to gain access to the system.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

userRole 1.3.6.1.4.1.17713.5.25.2.1.3
Role of the selected user. A Security Officer has access to and can modify all settings. A System Administrator has access to and can modify all non-security settings. A Read Only user can view settings, but cannot make any changes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER readOnly(0), systemAdministrator(1), securityOfficer(2)  

userEnabled 1.3.6.1.4.1.17713.5.25.2.1.4
Enable / Disable the selected user
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

userPassword 1.3.6.1.4.1.17713.5.25.2.1.5
User password, which must be entered in order to gain access to the system.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

syslogClient 1.3.6.1.4.1.17713.5.24.1
Enable or disable the syslog client
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

syslogState 1.3.6.1.4.1.17713.5.24.2
The syslog service has been enabled or disabled
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

longitude 1.3.6.1.4.1.17713.5.96.1
The longitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..19)  

latitude 1.3.6.1.4.1.17713.5.96.2
The latitude of the unit, measured in decimal degrees. This object is set by the SNMP manager and has no internal function.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..19)  

altitude 1.3.6.1.4.1.17713.5.96.3
The altitude of the unit, measured in metres. This object is set by the SNMP manager and has no internal function.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

channelChangeTrap 1.3.6.1.4.1.17713.5.99.0.1
The PTP radio has changed wireless channel. This has been caused by either i) mandatory radar avoidance, a DFS impulsive interference event will also be detected, or ii) Dynamic Spectrum Optimization, (DSO) DSO improves link performance by selecting the most appropriate transmit and receive channels with the lowest level of interference.
Status: current Access: read-write
NOTIFICATION-TYPE    

dfsImpulsiveInterferenceTrap 1.3.6.1.4.1.17713.5.99.0.2
DFS impulsive interference detected event
Status: current Access: read-write
NOTIFICATION-TYPE    

dataPortStatusTrap 1.3.6.1.4.1.17713.5.99.0.3
Current status of the Ethernet link. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

telecomsChannelStatusTrap 1.3.6.1.4.1.17713.5.99.0.4
Current status of telecoms channel. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

telecomsLoopbackTrap 1.3.6.1.4.1.17713.5.99.0.6
The loopback status of telecoms channel. This is intended for installation testing and should be set to 'None' for normal operation. The wire connections to a unit can be tested by applying a 'Copper' loopback to the local unit. The wireless connection to the remote unit can be tested by applying a 'Wireless' loopback to the remote unit with no loopback on the local unit. When applying a wireless loopback, please ensure that the other end of the link has a loopback setting of 'None'. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

regionCodeTrap 1.3.6.1.4.1.17713.5.99.0.8
The region code prohibits the wireless unit from operating outside the regulated limits. An invalid region code indicates a corrupted licence key. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

installStatusTrap 1.3.6.1.4.1.17713.5.99.0.9
A non-zero value indicates that signalling was received with the wrong MAC address or a mismatched link name. NB: It is very unusual to detect this, because units with mis-configured Target MAC Address will normally fail to establish a wireless link. However, rare circumstances may establish a partial wireless link and detect this situation. NB: A non-zero value on start-up, or a change of value during operation, may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

installArmStateTrap 1.3.6.1.4.1.17713.5.99.0.10
Indicates if the unit is being installed. NB: a value other than 'disarmed' on startup, or a change of state during operation may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

unitOutOfCalibrationTrap 1.3.6.1.4.1.17713.5.99.0.11
The unit is out of calibration
Status: current Access: read-write
NOTIFICATION-TYPE    

incompatibleRegionCodesTrap 1.3.6.1.4.1.17713.5.99.0.14
The master and slave units have incompatible region codes. NB: Both units must have compatible licence keys
Status: current Access: read-write
NOTIFICATION-TYPE    

noWirelessChannelAvailableTrap 1.3.6.1.4.1.17713.5.99.0.15
Spectrum Management was unable to locate a suitable wireless channel to operate on
Status: current Access: read-write
NOTIFICATION-TYPE    

wirelessLinkDisabledWarningTrap 1.3.6.1.4.1.17713.5.99.0.16
The SNMP ifAdminStatus of the wireless interface has disabled wireless traffic
Status: current Access: read-write
NOTIFICATION-TYPE    

dataPortDisabledWarningTrap 1.3.6.1.4.1.17713.5.99.0.17
The SNMP ifAdminStatus of the Ethernet interface has disabled Ethernet traffic
Status: current Access: read-write
NOTIFICATION-TYPE    

dataPortConfigurationMismatchTrap 1.3.6.1.4.1.17713.5.99.0.19
The detection of Ethernet fragments (runt packets) when the link is in full duplex is an indication of an auto-negotiation or forced configuration mismatch
Status: current Access: read-write
NOTIFICATION-TYPE    

incompatibleMasterAndSlaveTrap 1.3.6.1.4.1.17713.5.99.0.20
A non-zero value indicates that the master and slave ends of a link are different hardware products, or have different software versions. NB: It is very unusual to detect this, because incompatible units will normally fail to establish a wireless link. However, some combinations may establish a partial wireless link and detect this situation. NB: A non-zero value may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

sNTPSyncTrap 1.3.6.1.4.1.17713.5.99.0.21
If SNTP Sync fails then check the server settings in the Remote Management page, or disable SNTP. NB: a change of state may generate an SNMP trap and/or SMTP email alert
Status: current Access: read-write
NOTIFICATION-TYPE    

tDDSynchronizationAlarmTrap 1.3.6.1.4.1.17713.5.99.0.22
Not Synchronized indicates failure of the external timing system for a period greater than the holdover timer. TDD frame timing will have drifted, and this link may cause interference with other links in a synchronized network. Timing System Failure is an early warning, indicating that 80% of the holdover period has expired.
Status: current Access: read-write
NOTIFICATION-TYPE    

linkModeOptimizationMismatchTrap 1.3.6.1.4.1.17713.5.99.0.25
The remote node of this link has been configured with a different link mode optimization
Status: current Access: read-write
NOTIFICATION-TYPE    

capacityLicenseMismatchTrap 1.3.6.1.4.1.17713.5.99.0.27
The local and remote units have different licensed capacity and/or the full capacity trial has been activated at only one unit. The wireless link is operating at the capacity of the lowest capacity unit
Status: current Access: read-write
NOTIFICATION-TYPE    

syslogStateTrap 1.3.6.1.4.1.17713.5.99.0.30
The syslog service has been enabled or disabled
Status: current Access: read-write
NOTIFICATION-TYPE    

syslogLocalNearlyFullTrap 1.3.6.1.4.1.17713.5.99.0.31
The syslog local log is nearly full (90%)
Status: current Access: read-write
NOTIFICATION-TYPE    

syslogLocalWrappedTrap 1.3.6.1.4.1.17713.5.99.0.32
The syslog local log has wrapped
Status: current Access: read-write
NOTIFICATION-TYPE    

syslogClientTrap 1.3.6.1.4.1.17713.5.99.0.33
Enable or disable the syslog client
Status: current Access: read-write
NOTIFICATION-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor