BSUCLK-MIB
File:
BSUCLK-MIB.mib (4026 bytes)
Imported modules
Imported symbols
Defined Values
aniBsuClock |
1.3.6.1.4.1.4325.3.4 |
This module is used to configure the clock time on the BSU. BSUs
need to obtain and set their current clock time at boot up.
Sus will communicate with the BSU during their own boot up
and set their own clock time to that of BSU.
Time at the BSU can be set either through SNTP or manually.
It is recommended to use SNTP to obtain time.
|
MODULE-IDENTITY |
|
|
|
aniBsuClkSntpTimeZone |
1.3.6.1.4.1.4325.3.4.1 |
This is used to set the appropriate Time Zone offset from GMT.
The format of data should be +Hour:Min or -Hour:Min.
The valid Hour should be between -13 to +14
The valid Min should be 00,15,30 or 45
For example: +12:00 or +12:30 or -3:45
|
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..6) |
|
aniBsuClkSntpDstEnable |
1.3.6.1.4.1.4325.3.4.2 |
This shows whether Daylight Saving is enabled or not.
It gives user the option to incorporate Daylight Saving Time
in the configuration.
|
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
aniBsuClkSntpDstStart |
1.3.6.1.4.1.4325.3.4.3 |
Used to specify the start of Daylight Saving Time which should be
entered in the 'mmddhh' format where m - month, d - day and h - hour.
Can and must be set only if aniBsuClkSntpDstEnable is enabled.
|
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..6) |
|
aniBsuClkSntpDstEnd |
1.3.6.1.4.1.4325.3.4.4 |
Used to specify the end of Daylight Saving Time which should be
entered in the 'mmddhh' format where m - month, d - day and h - hour.
Can and must be set only if aniBsuClkSntpDstEnable is enabled.
|
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..6) |
|
aniBsuClkSntpEnable |
1.3.6.1.4.1.4325.3.4.5 |
This flag is used to enable(1) or disable(2) SNTP.
It is recommended to use SNTP rather than manually setting the time
to avoid errors in clock times simply due to manual entry across
various BSUs.
|
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
aniBsuClkManualTime |
1.3.6.1.4.1.4325.3.4.6 |
Used to specify the local clock time manually. It should be
entered in the 'mm/dd/yyyy hh:mm:ss' format that is,
month/day/year hour:minute:second.
When the user sends a set request on this parameter, the
aniBsuClkSntpEnable value is automatically set to disable(2), to set
this manual time entry on BSU.
|
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..19) |
|
aniBsuClkCurrentTime |
1.3.6.1.4.1.4325.3.4.7 |
The Current Time in 'mm/dd/yy hh:mm:ss' format, that is,
month/day/year hour:minute:second.
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..17) |
|