BAS-ALIAS-CABLE-DEVICE-MIB

File: BAS-ALIAS-CABLE-DEVICE-MIB.mib (56251 bytes)

Imported modules

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	IpAddress
Unsigned32	Integer32	Counter32
DisplayString	RowStatus	DateAndTime
TruthValue	TEXTUAL-CONVENTION	basAliasDocsCd
BasChassisId	BasSlotId	BasInterfaceId
BasLogicalPortId

Defined Types

InterfaceIndexOrZero
This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced.
TEXTUAL-CONVENTION
	Integer32	0..2147483647

BasDocsDevBaseEntry
SEQUENCE
	basDocsDevRole	INTEGER
	basDocsDevDateTime	DateAndTime
	basDocsDevResetNow	TruthValue
	basDocsDevSerialNumber	DisplayString
	basDocsDevSTPControl	INTEGER
	basDocsDevChassis	BasChassisId
	basDocsDevSlot	BasSlotId
	basDocsDevIf	BasInterfaceId
	basDocsDevLPort	BasLogicalPortId

BasDocsDevNmAccessEntry
SEQUENCE
	basDocsDevNmAccessIndex	INTEGER
	basDocsDevNmAccessIp	IpAddress
	basDocsDevNmAccessIpMask	IpAddress
	basDocsDevNmAccessCommunity	DisplayString
	basDocsDevNmAccessControl	INTEGER
	basDocsDevNmAccessInterfaces	OCTET STRING
	basDocsDevNmAccessStatus	RowStatus
	basDocsDevNmAccessChassis	BasChassisId
	basDocsDevNmAccessSlot	BasSlotId
	basDocsDevNmAccessIf	BasInterfaceId
	basDocsDevNmAccessLPort	BasLogicalPortId

BasDocsDevSwEntry
SEQUENCE
	basDocsDevSwServer	IpAddress
	basDocsDevSwFilename	DisplayString
	basDocsDevSwAdminStatus	INTEGER
	basDocsDevSwOperStatus	INTEGER
	basDocsDevSwChassis	BasChassisId
	basDocsDevSwSlot	BasSlotId
	basDocsDevSwIf	BasInterfaceId
	basDocsDevSwLPort	BasLogicalPortId

BasDocsDevServerEntry
SEQUENCE
	basDocsDevServerBootState	INTEGER
	basDocsDevServerDhcp	IpAddress
	basDocsDevServerTime	IpAddress
	basDocsDevServerTftp	IpAddress
	basDocsDevServerConfigFile	DisplayString
	basDocsDevServerChassis	BasChassisId
	basDocsDevServerSlot	BasSlotId
	basDocsDevServerIf	BasInterfaceId
	basDocsDevServerLPort	BasLogicalPortId

BasDocsDevEvEntry
SEQUENCE
	basDocsDevEvControl	INTEGER
	basDocsDevEvSyslog	IpAddress
	basDocsDevEvThrottleAdminStatus	INTEGER
	basDocsDevEvThrottleInhibited	TruthValue
	basDocsDevEvThrottleThreshold	Unsigned32
	basDocsDevEvThrottleInterval	INTEGER
	basDocsDevEvChassis	BasChassisId
	basDocsDevEvSlot	BasSlotId
	basDocsDevEvIf	BasInterfaceId
	basDocsDevEvLPort	BasLogicalPortId

BasDocsDevEvControlEntry
SEQUENCE
	basDocsDevEvPriority	INTEGER
	basDocsDevEvReporting	BITS
	basDocsDevEvControlChassis	BasChassisId
	basDocsDevEvControlSlot	BasSlotId
	basDocsDevEvControlIf	BasInterfaceId
	basDocsDevEvControlLPort	BasLogicalPortId

BasDocsDevEventEntry
SEQUENCE
	basDocsDevEvIndex	INTEGER
	basDocsDevEvFirstTime	DateAndTime
	basDocsDevEvLastTime	DateAndTime
	basDocsDevEvCount	Counter32
	basDocsDevEvLevel	INTEGER
	basDocsDevEvId	Unsigned32
	basDocsDevEvText	DisplayString
	basDocsDevEvEventChassis	BasChassisId
	basDocsDevEvEventSlot	BasSlotId
	basDocsDevEvEventIf	BasInterfaceId
	basDocsDevEvEventLPort	BasLogicalPortId

BasDocsDevFilterEntry
SEQUENCE
	basDocsDevFilterLLCDefault	INTEGER
	basDocsDevFilterChassis	BasChassisId
	basDocsDevFilterSlot	BasSlotId
	basDocsDevFilterIf	BasInterfaceId
	basDocsDevFilterLPort	BasLogicalPortId

BasDocsDevFilterLLCEntry
SEQUENCE
	basDocsDevFilterLLCIndex	INTEGER
	basDocsDevFilterLLCStatus	RowStatus
	basDocsDevFilterLLCIfIndex	InterfaceIndexOrZero
	basDocsDevFilterLLCProtocolType	INTEGER
	basDocsDevFilterLLCProtocol	INTEGER
	basDocsDevFilterLLCMatches	Counter32
	basDocsDevFilterLLCChassis	BasChassisId
	basDocsDevFilterLLCSlot	BasSlotId
	basDocsDevFilterLLCIf	BasInterfaceId
	basDocsDevFilterLLCLPort	BasLogicalPortId

BasDocsDevFilterIpDefEntry
SEQUENCE
	basDocsDevFilterIpDefault	INTEGER
	basDocsDevFilterIpDefChassis	BasChassisId
	basDocsDevFilterIpDefSlot	BasSlotId
	basDocsDevFilterIpDefIf	BasInterfaceId
	basDocsDevFilterIpDefLPort	BasLogicalPortId

BasDocsDevFilterIpEntry
SEQUENCE
	basDocsDevFilterIpIndex	INTEGER
	basDocsDevFilterIpStatus	RowStatus
	basDocsDevFilterIpControl	INTEGER
	basDocsDevFilterIpIfIndex	InterfaceIndexOrZero
	basDocsDevFilterIpDirection	INTEGER
	basDocsDevFilterIpBroadcast	TruthValue
	basDocsDevFilterIpSaddr	IpAddress
	basDocsDevFilterIpSmask	IpAddress
	basDocsDevFilterIpDaddr	IpAddress
	basDocsDevFilterIpDmask	IpAddress
	basDocsDevFilterIpProtocol	INTEGER
	basDocsDevFilterIpSourcePortLow	INTEGER
	basDocsDevFilterIpSourcePortHigh	INTEGER
	basDocsDevFilterIpDestPortLow	INTEGER
	basDocsDevFilterIpDestPortHigh	INTEGER
	basDocsDevFilterIpMatches	Counter32
	basDocsDevFilterIpChassis	BasChassisId
	basDocsDevFilterIpSlot	BasSlotId
	basDocsDevFilterIpIf	BasInterfaceId
	basDocsDevFilterIpLPort	BasLogicalPortId

Defined Values

basAliasDocsCdMib		1.3.6.1.4.1.3493.2.7.9.1
This MIB module defines the Alias DocsCd MIB objects for a Broadband Access System Cluster.
MODULE-IDENTITY

basDocsDevMIBObjects		1.3.6.1.4.1.3493.2.7.9.1.1
OBJECT IDENTIFIER

basDocsDevBase		1.3.6.1.4.1.3493.2.7.9.1.1.1
OBJECT IDENTIFIER

basDocsDevBaseTable		1.3.6.1.4.1.3493.2.7.9.1.1.1.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevBaseEntry

basDocsDevBaseEntry		1.3.6.1.4.1.3493.2.7.9.1.1.1.1.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevBaseEntry

basDocsDevRole		1.3.6.1.4.1.3493.2.7.9.1.1.1.1.1.1
Defines the current role of this device.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	cm(1), cmtsActive(2), cmtsBackup(3)

basDocsDevDateTime		1.3.6.1.4.1.3493.2.7.9.1.1.1.1.1.2
The date and time, with optional timezone information.
Status: current	Access: read-write
OBJECT-TYPE
	DateAndTime

basDocsDevResetNow		1.3.6.1.4.1.3493.2.7.9.1.1.1.1.1.3
Setting this object to true(1) causes the device to reset. Reading this object always returns false(2).
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

basDocsDevSerialNumber		1.3.6.1.4.1.3493.2.7.9.1.1.1.1.1.4
The manufacturer's serial number for this device.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

basDocsDevSTPControl		1.3.6.1.4.1.3493.2.7.9.1.1.1.1.1.5
This object controls operation of the spanning tree protocol (as distinguished from transparent bridging). If set to stEnabled(1) then the spanning tree protocol is enabled, subject to bridging constraints. If noStFilterBpdu(2), then spanning tree is not active, and Bridge PDUs received are discarded. If noStPassBpdu(3) then spanning tree is not active and Bridge PDUs are transparently forwarded. Note that a device need not implement all of these options, but that noStFilterBpdu(2) is required.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	stEnabled(1), noStFilterBpdu(2), noStPassBpdu(3)

basDocsDevChassis		1.3.6.1.4.1.3493.2.7.9.1.1.1.1.1.6
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevSlot		1.3.6.1.4.1.3493.2.7.9.1.1.1.1.1.7
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevIf		1.3.6.1.4.1.3493.2.7.9.1.1.1.1.1.8
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevLPort		1.3.6.1.4.1.3493.2.7.9.1.1.1.1.1.9
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId

basDocsDevNmAccessTable		1.3.6.1.4.1.3493.2.7.9.1.1.2
This table controls access to SNMP objects by network management stations. If the table is empty, access to SNMP objects is unrestricted.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevNmAccessEntry

basDocsDevNmAccessEntry		1.3.6.1.4.1.3493.2.7.9.1.1.2.1
Controls access to SNMP objects by a particular network management station. For each entry in this table, the contents are not readable unless the management station has read-write permission.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevNmAccessEntry

basDocsDevNmAccessIndex		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.1
Index used to order the application of access entries.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..2147483647

basDocsDevNmAccessIp		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.2
The IP address (or subnet) of the network management station. The address 255.255.255.255 is defined to mean any NMS. If traps are enabled for this entry, then the value must be the address of a specific device.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

basDocsDevNmAccessIpMask		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.3
The IP subnet mask of the network management stations. If traps are enabled for this entry, then the value must be 255.255.255.255.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

basDocsDevNmAccessCommunity		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.4
The community string to be matched for access by this entry. If set to the null string then any community string will match.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

basDocsDevNmAccessControl		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.5
Specifies the type of access allowed to this NMS. Setting this object to none(1) causes the table entry to be destroyed. Read(2) allows access by 'get' and 'get-next' PDUs. ReadWrite(3) allows access by 'set' as well. RoWithtraps(4), rwWithTraps(5), and trapsOnly(6) control distribution of Trap PDUs transmitted by this device.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	none(1), read(2), readWrite(3), roWithTraps(4), rwWithTraps(5), trapsOnly(6)

basDocsDevNmAccessInterfaces		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.6
Specifies the set of interfaces from which requests from this NMS will be accepted. Each octet within the value of this object specifies a set of eight interfaces, with the first octet specifying ports 1 through 8, the second octet specifying interfaces 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered interface, and the least significant bit represents the highest numbered interface. Thus, each interface is represented by a single bit within the value of this object. If that bit has a value of '1' then that interface is included in the set. Note that entries in this table apply only to link-layer interfaces (e.g., Ethernet and CATV MAC). Upstream and downstream channel interfaces must not be specified.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

basDocsDevNmAccessStatus		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.7
Controls and reflects the status of rows in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

basDocsDevNmAccessChassis		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.8
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevNmAccessSlot		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.9
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevNmAccessIf		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.10
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevNmAccessLPort		1.3.6.1.4.1.3493.2.7.9.1.1.2.1.11
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId

basDocsDevSoftware		1.3.6.1.4.1.3493.2.7.9.1.1.3
OBJECT IDENTIFIER

basDocsDevSwTable		1.3.6.1.4.1.3493.2.7.9.1.1.3.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevSwEntry

basDocsDevSwEntry		1.3.6.1.4.1.3493.2.7.9.1.1.3.1.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevSwEntry

basDocsDevSwServer		1.3.6.1.4.1.3493.2.7.9.1.1.3.1.1.1
The address of the TFTP server used for software upgrades.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

basDocsDevSwFilename		1.3.6.1.4.1.3493.2.7.9.1.1.3.1.1.2
The file name of the software image to be loaded into this device. Unless set via SNMP, this is the file name specified by the provisioning server that corresponds to the software version that is desired for this device. If unknown, the string '(unknown)' is returned.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..64)

basDocsDevSwAdminStatus		1.3.6.1.4.1.3493.2.7.9.1.1.3.1.1.3
If set to upgradeFromMgt(1), the device will initiate a TFTP software image download using docsDevSwFilename. After successfully receiving an image, the device will set its state to ignoreProvisioningUpgrade(3) and reboot. If the download process is interrupted by a reset or power failure, the device will load the previous image and, after re-initialization, continue to attempt loading the image specified in docsDevSwFilename. If set to allowProvisioningUpgrade(2), the device will use the software version information supplied by the provisioning server when next rebooting (this does not cause a reboot). When set to ignoreProvisioningUpgrade(3), the device will disregard software image upgrade information from the provisioning server. Note that reading this object can return upgradeFromMgt(1). This indicates that a software download is currently in progress, and that the device will reboot after successfully receiving an image.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	upgradeFromMgt(1), allowProvisioningUpgrade(2), ignoreProvisioningUpgrade(3)

basDocsDevSwOperStatus		1.3.6.1.4.1.3493.2.7.9.1.1.3.1.1.4
InProgress(1) indicates that a TFTP download is underway, either as a result of a version mismatch at provisioning or as a result of a upgradeFromMgt request. CompleteFromProvisioning(2) indicates that the last software upgrade was a result of version mismatch at provisioning. CompleteFromMgt(3) indicates that the last software upgrade was a result of setting docsDevSwAdminStatus to upgradeFromMgt. Failed(4) indicates that the last attempted download failed, ordinarily due to TFTP timeout.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inProgress(1), completeFromProvisioning(2), completeFromMgt(3), failed(4), other(5)

basDocsDevSwChassis		1.3.6.1.4.1.3493.2.7.9.1.1.3.1.1.5
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevSwSlot		1.3.6.1.4.1.3493.2.7.9.1.1.3.1.1.6
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevSwIf		1.3.6.1.4.1.3493.2.7.9.1.1.3.1.1.7
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevSwLPort		1.3.6.1.4.1.3493.2.7.9.1.1.3.1.1.8
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId

basDocsDevServer		1.3.6.1.4.1.3493.2.7.9.1.1.4
OBJECT IDENTIFIER

basDocsDevServerTable		1.3.6.1.4.1.3493.2.7.9.1.1.4.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevServerEntry

basDocsDevServerEntry		1.3.6.1.4.1.3493.2.7.9.1.1.4.1.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevServerEntry

basDocsDevServerBootState		1.3.6.1.4.1.3493.2.7.9.1.1.4.1.1.1
If operational(1), the device has completed loading and processing of configuration parameters and the CMTS has completed the Registration exchange. If disabled(2) then the device was administratively disabled, possibly by being refused network access in the configuration file. If waitingForDhcpOffer(3) then a DHCP Discover has been transmitted and no offer has yet been received. If waitingForDhcpResponse(4) then a DHCP Request has been transmitted and no response has yet been received. If waitingForTimeServer(5) then a Time Request has been transmitted and no response has yet been received. If waitingForTftp(6) then a request to the TFTP parameter server has been made and no response received. If refusedByCmts(7) then the Registration Request/Response exchange with the CMTS failed. If forwardingDenied(8) then the registration process completed, but the network access option in the received configuration file prohibits forwarding.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	operational(1), disabled(2), waitingForDhcpOffer(3), waitingForDhcpResponse(4), waitingForTimeServer(5), waitingForTftp(6), refusedByCmts(7), forwardingDenied(8), other(9), unknown(10)

basDocsDevServerDhcp		1.3.6.1.4.1.3493.2.7.9.1.1.4.1.1.2
The IP address of the DHCP server that assigned an IP address to this device. Returns 0.0.0.0 if DHCP was not used for IP address assignment.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

basDocsDevServerTime		1.3.6.1.4.1.3493.2.7.9.1.1.4.1.1.3
The IP address of the Time server (RFC-868).
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

basDocsDevServerTftp		1.3.6.1.4.1.3493.2.7.9.1.1.4.1.1.4
The IP address of the TFTP server responsible for downloading provisioning and configuration parameters to this device.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

basDocsDevServerConfigFile		1.3.6.1.4.1.3493.2.7.9.1.1.4.1.1.5
The name of the device configuration file read from the TFTP server.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

basDocsDevServerChassis		1.3.6.1.4.1.3493.2.7.9.1.1.4.1.1.6
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevServerSlot		1.3.6.1.4.1.3493.2.7.9.1.1.4.1.1.7
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevServerIf		1.3.6.1.4.1.3493.2.7.9.1.1.4.1.1.8
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevServerLPort		1.3.6.1.4.1.3493.2.7.9.1.1.4.1.1.9
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId

basDocsDevEvent		1.3.6.1.4.1.3493.2.7.9.1.1.5
OBJECT IDENTIFIER

basDocsDevEvTable		1.3.6.1.4.1.3493.2.7.9.1.1.5.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevEvEntry

basDocsDevEvEntry		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevEvEntry

basDocsDevEvControl		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1.1
Setting this object to resetLog(1) empties the event log. All data is deleted. Setting it to useDefaultReporting(2) returns all event priorities to their factory-default reporting. Reading this object always returns useDefaultReporting(2).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	resetLog(1), useDefaultReporting(2)

basDocsDevEvSyslog		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1.2
The IP address of the Syslog server. If 0.0.0.0, syslog transmission is inhibited.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

basDocsDevEvThrottleAdminStatus		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1.3
Controls the transmission of traps and syslog messages with respect to the trap pacing threshold. unconstrained(1) causes traps and syslog messages to be transmitted without regard to the threshold settings. maintainBelowThreshold(2) causes trap transmission and syslog messages to be suppressed if the number of traps would otherwise exceed the threshold. stopAtThreshold(3) causes trap transmission to cease at the threshold, and not resume until directed to do so. inhibited(4) causes all trap transmission and syslog messages to be suppressed. A single event is always treated as a single event for threshold counting. That is, an event causing both a trap and a syslog message is still treated as a single event. Writing to this object resets the thresholding state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unconstrained(1), maintainBelowThreshold(2), stopAtThreshold(3), inhibited(4)

basDocsDevEvThrottleInhibited		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1.4
If true(1), trap and syslog transmission is currently inhibited due to thresholds and/or the current setting of docsDevEvThrottleAdminStatus.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

basDocsDevEvThrottleThreshold		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1.5
Number of trap/syslog events per docsDevEvThrottleInterval to be transmitted before throttling. A single event is always treated as a single event for threshold counting. That is, an event causing both a trap and a syslog message is still treated as a single event.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

basDocsDevEvThrottleInterval		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1.6
The interval over which the trap threshold applies.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..2147483647

basDocsDevEvChassis		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1.7
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevEvSlot		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1.8
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevEvIf		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1.9
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevEvLPort		1.3.6.1.4.1.3493.2.7.9.1.1.5.1.1.10
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId

basDocsDevEvControlTable		1.3.6.1.4.1.3493.2.7.9.1.1.5.7
Allows control of the reporting of event classes.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevEvControlEntry

basDocsDevEvControlEntry		1.3.6.1.4.1.3493.2.7.9.1.1.5.7.1
Allows configuration of the reporting mechanisms for a particular event priority.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevEvControlEntry

basDocsDevEvPriority		1.3.6.1.4.1.3493.2.7.9.1.1.5.7.1.1
The priority level that is controlled by this entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	emergency(1), alert(2), critical(3), error(4), warning(5), notice(6), information(7), debug(8)

basDocsDevEvReporting		1.3.6.1.4.1.3493.2.7.9.1.1.5.7.1.2
Defines the action to be taken on occurrence of this event class. Implementations may not necessarily support all options for all event classes, but at minimum must allow traps and syslogging to be disabled.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	local(0), traps(1), syslog(2)

basDocsDevEvControlChassis		1.3.6.1.4.1.3493.2.7.9.1.1.5.7.1.3
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevEvControlSlot		1.3.6.1.4.1.3493.2.7.9.1.1.5.7.1.4
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevEvControlIf		1.3.6.1.4.1.3493.2.7.9.1.1.5.7.1.5
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevEvControlLPort		1.3.6.1.4.1.3493.2.7.9.1.1.5.7.1.6
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId

basDocsDevEventTable		1.3.6.1.4.1.3493.2.7.9.1.1.5.8
Contains a log of network and device events that may be of interest in fault isolation and troubleshooting.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevEventEntry

basDocsDevEventEntry		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1
Describes a network or device event that may be of interest in fault isolation and troubleshooting.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevEventEntry

basDocsDevEvIndex		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.1
Provides relative ordering of the objects in the event log. This object will always increase except when (a) the log is reset via docsDevEvControl, (b) the device reboots and does not implement nonvolatile storage for this log, or (c) it reaches the value 2^31. The next entry for all the above cases is 1.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..2147483647

basDocsDevEvFirstTime		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.2
The time that this entry was created.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

basDocsDevEvLastTime		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.3
If multiple events are reported via the same entry, the time that the last event for this entry occurred.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

basDocsDevEvCount		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.4
The number of consecutive event instances reported by this entry.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

basDocsDevEvLevel		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.5
The priority level of this event.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	emergency(1), alert(2), critical(3), error(4), warning(5), notice(6), information(7), debug(8)

basDocsDevEvId		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.6
For this product, uniquely identifies the type of event that is reported by this entry.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

basDocsDevEvText		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.7
Provides a human-readable description of the event, including all relevant context (interface numbers, etc.).
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

basDocsDevEvEventChassis		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.8
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevEvEventSlot		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.9
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevEvEventIf		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.10
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevEvEventLPort		1.3.6.1.4.1.3493.2.7.9.1.1.5.8.1.11
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId

basDocsDevFilter		1.3.6.1.4.1.3493.2.7.9.1.1.6
OBJECT IDENTIFIER

basDocsDevFilterTable		1.3.6.1.4.1.3493.2.7.9.1.1.6.1
Contains a log of network and device events that may be of interest in fault isolation and troubleshooting.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevFilterEntry

basDocsDevFilterEntry		1.3.6.1.4.1.3493.2.7.9.1.1.6.1.1
Describes a network or device event that may be of interest in fault isolation and troubleshooting.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevFilterEntry

basDocsDevFilterLLCDefault		1.3.6.1.4.1.3493.2.7.9.1.1.6.1.1.1
If set to discard(1), all packets not matching an LLC filter will be discarded. If set to accept(2), all packets not matching an LLC filter will be accepted for further processing (e.g., bridging).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	discard(1), accept(2)

basDocsDevFilterChassis		1.3.6.1.4.1.3493.2.7.9.1.1.6.1.1.2
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevFilterSlot		1.3.6.1.4.1.3493.2.7.9.1.1.6.1.1.3
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevFilterIf		1.3.6.1.4.1.3493.2.7.9.1.1.6.1.1.4
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevFilterLPort		1.3.6.1.4.1.3493.2.7.9.1.1.6.1.1.5
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId

basDocsDevFilterLLCTable		1.3.6.1.4.1.3493.2.7.9.1.1.6.2
A list of filters to apply to (bridged) LLC traffic, which forwards or drops packets on the basis of the layer three protocol type.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevFilterLLCEntry

basDocsDevFilterLLCEntry		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1
Describes a single filter to apply to (bridged) LLC traffic received on a specified interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevFilterLLCEntry

basDocsDevFilterLLCIndex		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1.1
Index used for the identification of filters (note that LLC filter order is irrelevant).
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..2147483647

basDocsDevFilterLLCStatus		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1.2
Controls and reflects the status of rows in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

basDocsDevFilterLLCIfIndex		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1.3
The entry interface to which this filter applies. The value corresponds to ifIndex for either a CATV MAC or another network interface. If the value is zero, the filter applies to all interfaces. In Cable Modems, the default value is the customer side interface. In Cable Modem Termination Systems, this object has to be specified to create a row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

basDocsDevFilterLLCProtocolType		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1.4
The format of the value in docsDevFilterLLCProtocol: either a two-byte Ethernet Ethertype, or a one-byte 802.2 SAP value. EtherType(1) also applies to SNAP- encapsulated frames.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ethertype(1), dsap(2)

basDocsDevFilterLLCProtocol		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1.5
The layer three protocol for which this filter applies. The protocol value format depends on docsDevFilterLLCProtocolType. Note that for SNAP frames, etherType filtering is performed rather than DSAP=0xAA.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

basDocsDevFilterLLCMatches		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1.6
Counts the number of times this filter was matched.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

basDocsDevFilterLLCChassis		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1.7
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevFilterLLCSlot		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1.8
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevFilterLLCIf		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1.9
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevFilterLLCLPort		1.3.6.1.4.1.3493.2.7.9.1.1.6.2.1.10
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId

basDocsDevFilterIpDefTable		1.3.6.1.4.1.3493.2.7.9.1.1.6.3
Contains a log of network and device events that may be of interest in fault isolation and troubleshooting.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevFilterIpDefEntry

basDocsDevFilterIpDefEntry		1.3.6.1.4.1.3493.2.7.9.1.1.6.3.1
Describes a network or device event that may be of interest in fault isolation and troubleshooting.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevFilterIpDefEntry

basDocsDevFilterIpDefault		1.3.6.1.4.1.3493.2.7.9.1.1.6.3.1.1
If set to discard(1), all packets not matching an IP filter will be discarded. If set to accept(2), all packets not matching an IP filter will be accepted for further processing (e.g., bridging).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	discard(1), accept(2)

basDocsDevFilterIpDefChassis		1.3.6.1.4.1.3493.2.7.9.1.1.6.3.1.2
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevFilterIpDefSlot		1.3.6.1.4.1.3493.2.7.9.1.1.6.3.1.3
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevFilterIpDefIf		1.3.6.1.4.1.3493.2.7.9.1.1.6.3.1.4
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevFilterIpDefLPort		1.3.6.1.4.1.3493.2.7.9.1.1.6.3.1.5
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId

basDocsDevFilterIpTable		1.3.6.1.4.1.3493.2.7.9.1.1.6.4
An ordered list of filters to apply to IP traffic. Filter application is ordered by the filter index, rather than by a best match algorithm. Packets which match no filters are discarded or forwarded according to the setting of docsDevFilterIpDefault.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BasDocsDevFilterIpEntry

basDocsDevFilterIpEntry		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1
Describes a filter to apply to IP traffic received on a specified interface. Both source and destination addresses must match for the filter to apply.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasDocsDevFilterIpEntry

basDocsDevFilterIpIndex		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.1
Index used to order the application of filters. The filter with the lowest index is always applied first.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	1..2147483647

basDocsDevFilterIpStatus		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.2
Controls and reflects the status of rows in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

basDocsDevFilterIpControl		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.3
If set to discard(1), all packets matching this filter will be discarded and scanning of the remainder of the filter list will be aborted. If set to accept(2), all packets matching this filter will be accepted for further processing (e.g., bridging) and scanning of the remainder of the filter list will be aborted.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	discard(1), accept(2)

basDocsDevFilterIpIfIndex		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.4
The entry interface to which this filter applies. The value corresponds to ifIndex for either a CATV MAC or another network interface. If the value is zero, the filter applies to all interfaces. Default value in Cable Modems is the customer-side interface. In Cable Modem Termination Systems, this object has to be specified to create a row in this table.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

basDocsDevFilterIpDirection		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.5
Determines whether the filter is applied to inbound(1) traffic, outbound(2) traffic, or traffic in both(3) directions.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	inbound(1), outbound(2), both(3)

basDocsDevFilterIpBroadcast		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.6
If set to true(1), the filter only applies to multicast and broadcast traffic. If set to false(2), the filter applies to all traffic.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

basDocsDevFilterIpSaddr		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.7
The source IP address, or portion thereof, that is to be matched for this filter.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

basDocsDevFilterIpSmask		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.8
A bit mask that is to be applied to the source address prior to matching. This mask is not necessarily the same as a subnet mask, but 1's bits must be leftmost and contiguous.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

basDocsDevFilterIpDaddr		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.9
The destination IP address, or portion thereof, that is to be matched for this filter
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

basDocsDevFilterIpDmask		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.10
A bit mask that is to be applied to the destination address prior to matching. This mask is not necessarily the same as a subnet mask, but 1's bits must be leftmost and contiguous
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

basDocsDevFilterIpProtocol		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.11
The IP protocol value that is to be matched.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	icmp(1), tcp(6), udp(17), any(256)

basDocsDevFilterIpSourcePortLow		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.12
If docsDevFilterIpProtocol is udp or tcp, this is the inclusive lower bound of the transport-layer source port range that is to be matched.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

basDocsDevFilterIpSourcePortHigh		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.13
If docsDevFilterIpProtocol is udp or tcp, this is the inclusive upper bound of the transport-layer source port range that is to be matched.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

basDocsDevFilterIpDestPortLow		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.14
If docsDevFilterIpProtocol is udp or tcp, this is the inclusive lower bound of the transport-layer destination port range that is to be matched.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

basDocsDevFilterIpDestPortHigh		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.15
If docsDevFilterIpProtocol is udp or tcp, this is the inclusive upper bound of the transport-layer destination port range that is to be matched.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

basDocsDevFilterIpMatches		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.16
Counts the number of times this filter was matched.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

basDocsDevFilterIpChassis		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.17
The BAS Chassis ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasChassisId

basDocsDevFilterIpSlot		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.18
The BAS Slot ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasSlotId

basDocsDevFilterIpIf		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.19
The BAS interface ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasInterfaceId

basDocsDevFilterIpLPort		1.3.6.1.4.1.3493.2.7.9.1.1.6.4.1.20
The BAS logical port ID of this card.
Status: current	Access: not-accessible
OBJECT-TYPE
	BasLogicalPortId