ATT-CNM-DS1-MIB
File:
ATT-CNM-DS1-MIB.mib (12768 bytes)
Imported modules
Imported symbols
Defined Types
AttCNMds1ConfigEntry |
|
SEQUENCE |
|
|
|
|
attCNMds1ConfigIndex |
INTEGER |
|
|
attCNMds1LineType |
INTEGER |
|
|
attCNMds1ZeroCoding |
INTEGER |
|
|
attCNMds1ErrorsMaxIntervals |
INTEGER |
|
|
attCNMds1ErrorsIntervalLen |
INTEGER |
|
AttCNMds1StatusEntry |
|
SEQUENCE |
|
|
|
|
attCNMds1StatusIndex |
INTEGER |
|
|
attCNMds1LineStatus |
INTEGER |
|
AttCNMds1ErrorsEntry |
|
SEQUENCE |
|
|
|
|
attCNMds1ErrorsIndex |
INTEGER |
|
|
attCNMds1ErrorsInterval |
INTEGER |
|
|
attCNMds1ErrorsTimeStamp |
INTEGER |
|
|
attCNMds1ErrorsLocalTime |
DisplayString |
|
|
attCNMds1LCVs |
Gauge |
|
|
attCNMds1LESs |
Gauge |
|
|
attCNMds1LSESs |
Gauge |
|
|
attCNMds1CVs |
Gauge |
|
|
attCNMds1ESs |
Gauge |
|
|
attCNMds1SESs |
Gauge |
|
|
attCNMds1SEFSs |
Gauge |
|
|
attCNMds1UASs |
Gauge |
|
Defined Values
att-2 |
1.3.6.1.4.1.74 |
OBJECT IDENTIFIER |
|
|
|
att-mgmt |
1.3.6.1.4.1.74.2 |
OBJECT IDENTIFIER |
|
|
|
att-cnm |
1.3.6.1.4.1.74.2.15 |
OBJECT IDENTIFIER |
|
|
|
attCNMds1ConfigTable |
1.3.6.1.4.1.74.2.15.3.1 |
A list of entries containing configuration
information for all DS1 interfaces managed by
this system. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AttCNMds1ConfigEntry |
|
attCNMds1ConfigEntry |
1.3.6.1.4.1.74.2.15.3.1.1 |
An entry containing configuration information
for a particular DS1 interface. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AttCNMds1ConfigEntry |
|
|
attCNMds1ConfigIndex |
1.3.6.1.4.1.74.2.15.3.1.1.1 |
A unique value for each DS1 interface. The interface
identified by a particular value of this index is
the same interface as identified by the same value
of an attCNMifConfigIndex object instance. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds1LineType |
1.3.6.1.4.1.74.2.15.3.1.1.2 |
This variable indicates the variety of DS1 frame
format supported by this interface.
For SMDS, this variable will have the value
ds1ANSI-ESF, denoting that this interface
supports the DS1 Extended Super Frame format
as specified by ANSI. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
other(1), ds1ESF(2), ds1D4(3), ds1ANSI-ESF(4), ds1G704(5), ds1G704-CRC(6) |
|
attCNMds1ZeroCoding |
1.3.6.1.4.1.74.2.15.3.1.1.3 |
This variable describes the variety of zero
code suppression/substitution used on the DS1
interface. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
ds1JammedBit(1), ds1B8ZS(2), ds1InvertedHDLC(3), ds1HDB3(4), ds1ZBTSI(5) |
|
attCNMds1ErrorsMaxIntervals |
1.3.6.1.4.1.74.2.15.3.1.1.4 |
This variable identifies the maximum number
of measurement intervals supported for the
error counts maintained by this DS1 interface
in the attCNMds1ErrorsTable. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds1ErrorsIntervalLen |
1.3.6.1.4.1.74.2.15.3.1.1.5 |
This variable identifies the number of seconds
that make up one complete measurement interval for
the error counts maintained by this DS1 interface
in the attCNMds1ErrorsTable. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds1StatusTable |
1.3.6.1.4.1.74.2.15.3.2 |
A list of entries containing status information
for all DS1 interfaces managed by this system. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AttCNMds1StatusEntry |
|
attCNMds1StatusEntry |
1.3.6.1.4.1.74.2.15.3.2.1 |
An entry containing status information for a
particular DS1 interface. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AttCNMds1StatusEntry |
|
|
attCNMds1StatusIndex |
1.3.6.1.4.1.74.2.15.3.2.1.1 |
A unique value for each DS1 interface. The interface
identified by a particular value of this index is
the same interface as identified by the same value
of an attCNMifConfigIndex object instance. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds1LineStatus |
1.3.6.1.4.1.74.2.15.3.2.1.2 |
This variable indicates the most Line Status
of this interface. This object is a bit map
represented as a sum, therefore, it can represent
multiple failures (alarms) simultaneously. The
various bit positions are:
1 No Alarm Present
2 Yellow Alarm
4 Near End Alarm-Indication-Signal (AIS)
8 Near End Loss-Of-Frame (LOF)
16 Near End Loss-Of-Signal (LOS)
For example, for an interface that has LOF and
LOS outstanding, this object will have a value
of 24. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds1ErrorsTable |
1.3.6.1.4.1.74.2.15.3.3 |
A list of entries containing protocol error counts,
maintained during the specified measurement interval,
for all DS1 interfaces managed by this system. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AttCNMds1ErrorsEntry |
|
attCNMds1ErrorsEntry |
1.3.6.1.4.1.74.2.15.3.3.1 |
An entry containing protocol error counts,
maintained during the specified measurement interval,
for a particular DS1 interface. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AttCNMds1ErrorsEntry |
|
|
attCNMds1ErrorsIndex |
1.3.6.1.4.1.74.2.15.3.3.1.1 |
A unique value for each DS1 interface. The interface
identified by a particular value of this index is
the same interface as identified by the same value
of an attCNMifConfigIndex object instance. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds1ErrorsInterval |
1.3.6.1.4.1.74.2.15.3.3.1.2 |
This variable identifies the measurement interval
number for which the measurement is provided. It is
a number between 1 and XX, where 1 identifies the
most recently completed measurement interval and XX
is the least recently completed measurement interval.
The value of XX is specified by the
attCNMds1ErrorsMaxIntervals object given in the
attCNMds1ConfigTable.
The maximum length of each measurement interval is
specified by the attCNMds1ErrorsIntervalLen object
given in the attCNMds1ConfigTable. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds1ErrorsTimeStamp |
1.3.6.1.4.1.74.2.15.3.3.1.3 |
The time stamp corresponding to the end of the
specified measurement interval, as measured in
seconds from 00:00:00 UTC (Coordinated Universal
Time) January 1, 1970. Any fraction is rounded up. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
attCNMds1ErrorsLocalTime |
1.3.6.1.4.1.74.2.15.3.3.1.4 |
The time stamp corresponding to the end of the
specified measurement interval. Any fraction is
rounded up. It is given as a printable ASCII string
showing the local time at the end of the interval. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
Size(0..255) |
|
attCNMds1LCVs |
1.3.6.1.4.1.74.2.15.3.3.1.5 |
The counter associated with the number of Line
Code Violations encountered by a DS1 interface
during the specified measurement interval.
A Line Code Violation is the occurrence of a
received Bipolar Violation that is not part of a
zero-substitution code.
The Bipolar Violation Rate is generally viewed as
approximating the Bit Error Rate. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds1LESs |
1.3.6.1.4.1.74.2.15.3.3.1.6 |
The counter associated with the number of Line
Errored Seconds encountered by a DS1 interface
during the specified measurement interval.
A Line Errored Second is any second with at least
one Line Code Violation. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds1LSESs |
1.3.6.1.4.1.74.2.15.3.3.1.7 |
The counter associated with the number of Line
Severely Errored Seconds encountered by a DS1
interface during the specified measurement interval.
A Line Severely Errored Second is any second with
16 or more Lince Code Violations monitored at the
DS1 rate. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds1CVs |
1.3.6.1.4.1.74.2.15.3.3.1.8 |
The counter associated with the number of Code
Violations encountered by a DS1 interface during
the specified measurement interval.
A Code Violation is the occurrence of a received
CRC-6 code that is not identical to the corresponding
locally-calculated code. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds1ESs |
1.3.6.1.4.1.74.2.15.3.3.1.9 |
The counter associated with the number of Errored
Seconds encountered by a DS1 interface during the
specified measurement interval.
An Errored Second is any second with at least one
Code Violation. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds1SESs |
1.3.6.1.4.1.74.2.15.3.3.1.10 |
The counter associated with the number of Severely
Errored Seconds encountered by a DS1 interface
during the specified measurement interval.
A Severely Errored Second is any second with 15 or
more Code Violations monitored at the DS1 rate. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds1SEFSs |
1.3.6.1.4.1.74.2.15.3.3.1.11 |
The counter associated with the number of Severely
Errored Framing Seconds encountered by a DS1
interface during the specified measurement interval.
A Severely Errored Framing Second is any second
during which one or more Severely Errored Framing
(SEF) events occurred. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|
attCNMds1UASs |
1.3.6.1.4.1.74.2.15.3.3.1.12 |
The counter associated with the number of
Unavailable Seconds encountered by a DS1
interface during the specified measurement interval.
An Unavailable Second is any second during which
the DS1 interface was unavailable to offer service. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Gauge |
|
|