ATM-FORUM-M4-MIB

File: ATM-FORUM-M4-MIB.mib (178793 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB ATM-FORUM-TC-MIB ATM-MIB
ENTITY-MIB HOST-RESOURCES-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
OBJECT-IDENTITY Counter32 Integer32
IpAddress Unsigned32 TEXTUAL-CONVENTION
DisplayString AutonomousType RowStatus
TestAndIncr RowPointer TruthValue
TimeStamp DateAndTime TimeInterval
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
ifIndex OwnerString atmForum
atmVplEntry atmVclEntry atmVpCrossConnectEntry
atmVcCrossConnectEntry atmVplVpi atmVclVpi
atmVclVci atmVpCrossConnectIndex atmVpCrossConnectLowIfIndex
atmVpCrossConnectLowVpi atmVpCrossConnectHighIfIndex atmVpCrossConnectHighVpi
atmVcCrossConnectIndex atmVcCrossConnectLowIfIndex atmVcCrossConnectLowVpi
atmVcCrossConnectLowVci atmVcCrossConnectHighIfIndex atmVcCrossConnectHighVpi
atmVcCrossConnectHighVci entPhysicalIndex entPhysicalClass
entPhysicalContainedIn entPhysicalParentRelPos hrSWInstalledIndex
hrSWInstalledName

Defined Types

AtmfM4PhysPathTpEntry  
SEQUENCE    
  atmfM4PhysPathTpHwUnitIndex Integer32
  atmfM4PhysPathTpPortID Integer32
  atmfM4PhysPathTpAlarmSeverityIndex Integer32

AtmfM4TcAdaptorEntry  
SEQUENCE    
  atmfM4TcACellScrambling TruthValue
  atmfM4TcAlarmSeverityIndex Integer32

AtmfM4AtmLayerEntry  
SEQUENCE    
  atmfM4IfType INTEGER
  atmfM4IfLoopbackLocationCode Integer32
  atmfM4IfSubscriberAddress DisplayString
  atmfM4IfPreferredCarrier DisplayString
  atmfM4IfFarEndCarrierNetwork DisplayString

AtmfM4VplEntry  
SEQUENCE    
  atmfM4VplSegEndPt TruthValue

AtmfM4VclEntry  
SEQUENCE    
  atmfM4VclSegEndPt TruthValue

AtmfM4VpXConnEntry  
SEQUENCE    
  atmfM4VpXConnRecover TruthValue

AtmfM4VcXConnEntry  
SEQUENCE    
  atmfM4VcXConnRecover TruthValue

AtmfM4VpNextVpiEntry  
SEQUENCE    
  atmfM4VpNextVpiValue INTEGER

AtmfM4VcNextVciEntry  
SEQUENCE    
  atmfM4VcNextVciValue INTEGER

AtmfM4CellProtoCurrEntry  
SEQUENCE    
  atmfM4CellProtoCurrSuspect TruthValue
  atmfM4CellProtoCurrElapsedTime TimeInterval
  atmfM4CellProtoCurrSupprIntvls Counter32
  atmfM4CellProtoCurrProtoErrors Counter32
  atmfM4CellProtoCurrInOAMCells Counter32

AtmfM4CellProtoHistEntry  
SEQUENCE    
  atmfM4CellProtoHistIndex INTEGER
  atmfM4CellProtoHistSuspect TruthValue
  atmfM4CellProtoHistElapsedTime TimeInterval
  atmfM4CellProtoHistSupprIntvls Counter32
  atmfM4CellProtoHistProtoErrors Counter32
  atmfM4CellProtoHistInOAMCells Counter32

AtmfM4CellProtoErrorEntry  
SEQUENCE    
  atmfM4CellProtoErrorCode Integer32
  atmfM4CellProtoErrorTime TimeStamp
  atmfM4CellProtoErrorReason Integer32
  atmfM4CellProtoErrorVpi INTEGER
  atmfM4CellProtoErrorVci INTEGER

AtmfM4TcProtoCurrEntry  
SEQUENCE    
  atmfM4TcProtoCurrSuspect TruthValue
  atmfM4TcProtoCurrElapsedTime TimeInterval
  atmfM4TcProtoCurrSupprIntvls Counter32
  atmfM4TcProtoCurrDiscardHECViol Counter32

AtmfM4TcProtoHistEntry  
SEQUENCE    
  atmfM4TcProtoHistIndex INTEGER
  atmfM4TcProtoHistSuspect TruthValue
  atmfM4TcProtoHistElapsedTime TimeInterval
  atmfM4TcProtoHistSupprIntvls Unsigned32
  atmfM4TcProtoHistDiscardHECViol Unsigned32

AtmfM4VpUpcNpcCurrEntry  
SEQUENCE    
  atmfM4VpUpcNpcCurrSuspect TruthValue
  atmfM4VpUpcNpcCurrElapsedTime TimeInterval
  atmfM4VpUpcNpcCurrSupprIntvls Counter32
  atmfM4VpUpcNpcCurrDiscardedCells Counter32
  atmfM4VpUpcNpcCurrDiscardedClp0 Counter32
  atmfM4VpUpcNpcCurrPassedCells Counter32
  atmfM4VpUpcNpcCurrPassedClp0 Counter32

AtmfM4VpUpcNpcHistEntry  
SEQUENCE    
  atmfM4VpUpcNpcHistIndex INTEGER
  atmfM4VpUpcNpcHistSuspect TruthValue
  atmfM4VpUpcNpcHistElapsedTime TimeInterval
  atmfM4VpUpcNpcHistSupprIntvls Unsigned32
  atmfM4VpUpcNpcHistDiscardedCells Unsigned32
  atmfM4VpUpcNpcHistDiscardedClp0 Unsigned32
  atmfM4VpUpcNpcHistPassedCells Unsigned32
  atmfM4VpUpcNpcHistPassedClp0 Unsigned32

AtmfM4VcUpcNpcCurrEntry  
SEQUENCE    
  atmfM4VcUpcNpcCurrSuspect TruthValue
  atmfM4VcUpcNpcCurrElapsedTime TimeInterval
  atmfM4VcUpcNpcCurrSupprIntvls Counter32
  atmfM4VcUpcNpcCurrDiscardedCells Counter32
  atmfM4VcUpcNpcCurrDiscardedClp0 Counter32
  atmfM4VcUpcNpcCurrPassedCells Counter32
  atmfM4VcUpcNpcCurrPassedClp0 Counter32

AtmfM4VcUpcNpcHistEntry  
SEQUENCE    
  atmfM4VcUpcNpcHistIndex INTEGER
  atmfM4VcUpcNpcHistSuspect TruthValue
  atmfM4VcUpcNpcHistElapsedTime TimeInterval
  atmfM4VcUpcNpcHistSupprIntvls Unsigned32
  atmfM4VcUpcNpcHistDiscardedCells Unsigned32
  atmfM4VcUpcNpcHistDiscardedClp0 Unsigned32
  atmfM4VcUpcNpcHistPassedCells Unsigned32
  atmfM4VcUpcNpcHistPassedClp0 Unsigned32

AtmfM4VpTestEntry  
SEQUENCE    
  atmfM4VpTestObject INTEGER
  atmfM4VpTestId TestAndIncr
  atmfM4VpTestStatus INTEGER
  atmfM4VpTestType AutonomousType
  atmfM4VpTestResult INTEGER
  atmfM4VpTestCode OBJECT IDENTIFIER
  atmfM4VpTestOwner OwnerString

AtmfM4VcTestEntry  
SEQUENCE    
  atmfM4VcTestObject INTEGER
  atmfM4VcTestId TestAndIncr
  atmfM4VcTestStatus INTEGER
  atmfM4VcTestType AutonomousType
  atmfM4VcTestResult INTEGER
  atmfM4VcTestCode OBJECT IDENTIFIER
  atmfM4VcTestOwner OwnerString

AtmfM4EquipEntry  
SEQUENCE    
  atmfM4EquipAdminStatus INTEGER
  atmfM4EquipLocation DisplayString
  atmfM4EquipOperStatus INTEGER
  atmfM4EquipVendor DisplayString
  atmfM4EquipVersion AutonomousType
  atmfM4EquipUserLabel DisplayString
  atmfM4EquipAlarmSeverityIndex Integer32

AtmfM4EquipHolderEntry  
SEQUENCE    
  atmfM4EquipHolderType INTEGER
  atmfM4EquipHolderAcceptableTypes DisplayString
  atmfM4EquipHolderSlotStatus INTEGER
  atmfM4EquipHolderSwLoad INTEGER

AtmfM4PlugInUnitEntry  
SEQUENCE    
  atmfM4PlugInUnitAdminStatus INTEGER
  atmfM4PlugInUnitAvailStatus INTEGER
  atmfM4PlugInUnitOperStatus INTEGER
  atmfM4PlugInUnitVendor DisplayString
  atmfM4PlugInUnitVersion AutonomousType
  atmfM4PlugInUnitAlarmSeverityIndex Integer32

AtmfM4HwRunningSwEntry  
SEQUENCE    
  atmfM4HwRunningSwHwIndex INTEGER
  atmfM4HwRunningSwIndex INTEGER
  atmfM4HwRunningSwSwIndex INTEGER

AtmfM4HwInstalledSwEntry  
SEQUENCE    
  atmfM4HwInstalledSwHwIndex INTEGER
  atmfM4HwInstalledSwIndex INTEGER
  atmfM4HwInstalledSwSwIndex INTEGER
  atmfM4HwSwAlarmSeverityIndex Integer32

AtmfM4AlarmLogSeverity  
The value of this object identifies the severity of an alarm in the log, including 'cleared'.
TEXTUAL-CONVENTION    
  INTEGER cleared(-1), indeterminate(0), critical(1), major(2), minor(3), warning(4)  

AtmfM4AlarmSeverity  
The value of this object identifies the severity of an alarm that has occurred. (Note that there is no value corresponding to 'cleared'.)
TEXTUAL-CONVENTION    
  INTEGER indeterminate(0), critical(1), major(2), minor(3), warning(4)  

AtmfM4AlarmSevProfileEntry  
SEQUENCE    
  atmfM4AlarmSevProfileIndex Integer32
  atmfM4AlarmSevProfileRowStatus RowStatus

AtmfM4AlarmSevEntry  
SEQUENCE    
  atmfM4AlarmSevTrapId Integer32
  atmfM4AlarmSeverity AtmfM4AlarmSeverity

AtmfM4TrapForwardingEntry  
SEQUENCE    
  atmfM4TrapForwardingIndex Integer32
  atmfM4TrapForwardingDest IpAddress
  atmfM4ForwardedTrapId Integer32
  atmfM4ForwardedTrapObject RowPointer
  atmfM4TrapForwardingPort Integer32
  atmfM4LowestForwardedSeverity AtmfM4AlarmSeverity
  atmfM4ForwardedIndeterminate TruthValue
  atmfM4TrapForwardingRowStatus RowStatus

AtmfM4TrapLogEntry  
SEQUENCE    
  atmfM4TrapLogSrc IpAddress
  atmfM4TrapLogType INTEGER
  atmfM4TrapLogAdminStatus INTEGER
  atmfM4TrapLogOperStatus INTEGER
  atmfM4TrapLogFullAction INTEGER
  atmfM4TrapLogRowStatus RowStatus

AtmfM4LoggedTrapEntry  
SEQUENCE    
  atmfM4LoggedTrapIndex Unsigned32
  atmfM4LoggedTrapTime DateAndTime
  atmfM4LoggedTrapID Integer32
  atmfM4LoggedTrapObject RowPointer
  atmfM4LoggedTrapRowStatus RowStatus

AtmfM4LoggedAlarmEntry  
SEQUENCE    
  atmfM4LoggedAlarmSeverity AtmfM4AlarmLogSeverity
  atmfM4LoggedAlarmBackedUp TruthValue
  atmfM4LoggedAlarmBUObject RowPointer
  atmfM4LoggedAlarmSpecificProb DisplayString
  atmfM4LoggedAlarmRepairAct DisplayString

Defined Values

atmfM4MIB 1.3.6.1.4.1.353.100
This MIB module is the SNMP version of the ATM Forum's M4 interface (network element view).
MODULE-IDENTITY    

atmfM4MIBObjects 1.3.6.1.4.1.353.100.1
OBJECT IDENTIFIER    

atmfM4MIBTraps 1.3.6.1.4.1.353.100.2
OBJECT IDENTIFIER    

atmfM4MIBCompliance 1.3.6.1.4.1.353.100.3
OBJECT IDENTIFIER    

atmfM4NeVendor 1.3.6.1.4.1.353.100.1.1
The vendor of the ATM network element.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

atmfM4NeVersion 1.3.6.1.4.1.353.100.1.2
The version of the ATM network element.
Status: current Access: read-only
OBJECT-TYPE    
  AutonomousType  

atmfM4NeStartTime 1.3.6.1.4.1.353.100.1.3
The time at which the agent was last started; in other words, the time at which sysUpTime was zero.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

atmfM4NeAlarmSeverityIndex 1.3.6.1.4.1.353.100.1.4
An index into the alarm severity profile table, specifying the severity assignments for M4 alarms reported for the ATM network element.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

atmfM4NeSuppressZeroStats 1.3.6.1.4.1.353.100.1.5
When the value of this object is true, no entry will be created in any of the the historical statistics tables for intervals in which all counts are zero.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

atmfM4PhysPathTpTable 1.3.6.1.4.1.353.100.1.6
The ATM Forum M4 interface Configuration table extensions for the physical path termination point.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4PhysPathTpEntry

atmfM4PhysPathTpEntry 1.3.6.1.4.1.353.100.1.6.1
Columns conceptually added to the interface table entry for an ATM interface to model the physical path termination point. The row of the interface table modeling this object should also include columns for the TC Adaptor object and the ATM interface table defined in RFC 1695. The interface table entry for the physical path TP fields of an ATM interface are set up without management system control (or else that setup is outside the scope of M4).
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4PhysPathTpEntry  

atmfM4PhysPathTpHwUnitIndex 1.3.6.1.4.1.353.100.1.6.1.1
Specifies the index of the entry in the entPhysicalTable that represents the device (i.e., card) on which the physical path terminates.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

atmfM4PhysPathTpPortID 1.3.6.1.4.1.353.100.1.6.1.2
Identifies the port (within the card identified by the hardware unit index) on which the physical path terminates.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2147483647  

atmfM4PhysPathTpAlarmSeverityIndex 1.3.6.1.4.1.353.100.1.6.1.3
Specifies the index of the entry in the communications alarm severity profile table that should be used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

atmfM4TcAdaptorTable 1.3.6.1.4.1.353.100.1.7
The ATM Forum M4 interface Configuration table extensions for the TC Adaptor.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4TcAdaptorEntry

atmfM4TcAdaptorEntry 1.3.6.1.4.1.353.100.1.7.1
Columns conceptually added to the interface table entry for an ATM interface to model the TC Adaptor. The row of the interface table modeling this object should also include columns for the physical path TP and the ATM interface table defined in RFC 1695. The interface table entry for the TC Adaptor fields of an ATM interface are set up without management system control (or else that setup is outside the scope of M4).
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4TcAdaptorEntry  

atmfM4TcACellScrambling 1.3.6.1.4.1.353.100.1.7.1.1
This attribute is used by the management system to activate and deactivate the ATM cell scrambling function. When the value of this attribute is TRUE, cell scrambling on the interface is activated. This attribute shall be present only for interfaces that support the deactivation of cell scrambling. The ATM Forum UNI specification requires cell scrambling for ATM/SONET interfaces but allows cell scrambling to be controlled (i.e., turned on and off) for ATM/DS3 interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

atmfM4TcAlarmSeverityIndex 1.3.6.1.4.1.353.100.1.7.1.2
Specifies the index of the entry in the communications alarm severity profile table that should be used.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

atmfM4AtmLayerTable 1.3.6.1.4.1.353.100.1.8
The ATM Forum M4 interface Configuration table extensions for the ATM cell layer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4AtmLayerEntry

atmfM4AtmLayerEntry 1.3.6.1.4.1.353.100.1.8.1
Columns conceptually added to the interface table entry for an ATM interface to model the ATM cell layer. The row of the interface table modeling this object should also include columns for the physical path TP and TC Adaptor object, as well as the ATM interface table defined in RFC 1695. The default configuration of an entry in this table is used whenever the entries for the physical path TP, etc., are created. The management system configures a UNI, B-ICI, or B-ISSI on the interface by first modifying the atmfM4IfType column (this can be done in the same SNMP set-request that sets up the other necessary variables.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4AtmLayerEntry  

atmfM4IfType 1.3.6.1.4.1.353.100.1.8.1.1
Specifies the type of ATM cell-layer interface defined on the physical path termination point modeled by this entry in the interface table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), uni(1), bici(2), bissi(3)  

atmfM4IfLoopbackLocationCode 1.3.6.1.4.1.353.100.1.8.1.2
Specifies the code that shall exist in incoming OAM Loopback cells that are to be looped back at this interface. A value of zero shall indicate that the management system has not set any loopback location code for this interface. Therefore, zero should not be used as the actual loopback location code for any interface. This object shall be present only for table entries that represent an actual ATM cell layer interface (i.e., the atmM4IfType is not none(0)).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

atmfM4IfSubscriberAddress 1.3.6.1.4.1.353.100.1.8.1.3
Specifies the address or newline-delimited list of addresses assigned to the UNI. This object shall be present only for table entries that represent an UNI interface.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

atmfM4IfPreferredCarrier 1.3.6.1.4.1.353.100.1.8.1.4
Specifies the name of the default carrier to use when one is not explicitly identified in the call set-up message. This object shall be present only for table entries that represent an UNI interface and only when SVC services are supported.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

atmfM4IfFarEndCarrierNetwork 1.3.6.1.4.1.353.100.1.8.1.5
Specifies the adjacent carrier to which the B-ICI transmission path is connected. This object shall be present only for table entries that represent an B-ICI interface and only when SVC services are supported.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

atmfM4VplTable 1.3.6.1.4.1.353.100.1.9
The ATM Forum M4 VPL Termination Point Configuration table extensions. This table augments the VPL configuration table in RFC 1695.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VplEntry

atmfM4VplEntry 1.3.6.1.4.1.353.100.1.9.1
Additional columns for the VPL configuration table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VplEntry  

atmfM4VplSegEndPt 1.3.6.1.4.1.353.100.1.9.1.1
Specifies whether the VPL termination point is a segment end-point.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

atmfM4VclTable 1.3.6.1.4.1.353.100.1.10
The ATM Forum M4 VCL Termination Point Configuration table extensions. This table augments the VCL configuration table in RFC 1695.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VclEntry

atmfM4VclEntry 1.3.6.1.4.1.353.100.1.10.1
Additional columns for the VCL configuration table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VclEntry  

atmfM4VclSegEndPt 1.3.6.1.4.1.353.100.1.10.1.1
Specifies whether the VCL termination point is a segment end-point.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

atmfM4VpXConnTable 1.3.6.1.4.1.353.100.1.11
The ATM Forum M4 VP Cross-Connect Configuration table extensions. This table augments the VP Cross-Connect configuration table in RFC 1695.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VpXConnEntry

atmfM4VpXConnEntry 1.3.6.1.4.1.353.100.1.11.1
Additional columns for the VP Cross-Connect table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VpXConnEntry  

atmfM4VpXConnRecover 1.3.6.1.4.1.353.100.1.11.1.1
If FALSE, this cross-connection will be removed on failure.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

atmfM4VcXConnTable 1.3.6.1.4.1.353.100.1.12
The ATM Forum M4 VC Cross-Connect Configuration table extensions. This table augments the VC Cross-Connect configuration table in RFC 1695.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VcXConnEntry

atmfM4VcXConnEntry 1.3.6.1.4.1.353.100.1.12.1
Additional columns for the VC Cross-Connect table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VcXConnEntry  

atmfM4VcXConnRecover 1.3.6.1.4.1.353.100.1.12.1.1
If FALSE, this cross-connection will be removed on failure.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

atmfM4VpNextVpiTable 1.3.6.1.4.1.353.100.1.13
The ATM Forum M4 VP Next-VPI value table. This optional table supplied unused VPI values for use in creating entries in the atmVplTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VpNextVpiEntry

atmfM4VpNextVpiEntry 1.3.6.1.4.1.353.100.1.13.1
Each entry in this table represents the 'next' VPI value available for a given ATM interface. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VpNextVpiEntry  

atmfM4VpNextVpiValue 1.3.6.1.4.1.353.100.1.13.1.1
This object contains an appropriate value to be used for atmVplVpi when creating entries in the atmVplTable. The value -1 indicates that no unassigned entries are available. To obtain the atmVplVpi value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index (or -1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -1..4095  

atmfM4VcNextVciTable 1.3.6.1.4.1.353.100.1.14
The ATM Forum M4 VC Next-VCI value table. This optional table supplied unused VCI values for use in creating entries in the atmVclTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VcNextVciEntry

atmfM4VcNextVciEntry 1.3.6.1.4.1.353.100.1.14.1
Each entry in this table represents the 'next' VCI value available for a given ATM interface. Each VPL Termination Point automatically has an entry in this table associated with it.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VcNextVciEntry  

atmfM4VcNextVciValue 1.3.6.1.4.1.353.100.1.14.1.1
This object contains an appropriate value to be used for atmVclVci when creating entries in the atmVclTable. The value -1 indicates that no unassigned entries are available. To obtain the atmVclVci value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index (or -1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -1..65535  

atmfM4CellProtoCurrTable 1.3.6.1.4.1.353.100.1.15
The ATM Forum M4 Cell Protocol Monitoring Current Data table. This table maintains per-interface statistics for the fifteen-minute interval currently being collected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4CellProtoCurrEntry

atmfM4CellProtoCurrEntry 1.3.6.1.4.1.353.100.1.15.1
An entry in the ATM Forum M4 Cell Protocol Monitoring Current Data table. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4CellProtoCurrEntry  

atmfM4CellProtoCurrSuspect 1.3.6.1.4.1.353.100.1.15.1.1
If true, the statistics in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

atmfM4CellProtoCurrElapsedTime 1.3.6.1.4.1.353.100.1.15.1.2
Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

atmfM4CellProtoCurrSupprIntvls 1.3.6.1.4.1.353.100.1.15.1.3
This attribute is non-zero only if the ATM NE is suppressing ATM Cell Protocol Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4CellProtoCurrProtoErrors 1.3.6.1.4.1.353.100.1.15.1.4
The number of ATM cells dropped on this interface, due to an unrecognized field or set of fields in the ATM cell header, since the start of this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4CellProtoCurrInOAMCells 1.3.6.1.4.1.353.100.1.15.1.5
The number of OAM cells received at this interface since the start of this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4CellProtoHistTable 1.3.6.1.4.1.353.100.1.16
The ATM Forum M4 Cell Protocol Monitoring History Data table. This table maintains per-interface statistics for previous fifteen-minute intervals.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4CellProtoHistEntry

atmfM4CellProtoHistEntry 1.3.6.1.4.1.353.100.1.16.1
An entry in the ATM Forum M4 Cell Protocol Monitoring History Data table. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it for each fifteen- minute interval in which statistics are collected for it.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4CellProtoHistEntry  

atmfM4CellProtoHistIndex 1.3.6.1.4.1.353.100.1.16.1.1
A number between 1 and 96, which identifies the interval for which the set of statistics in this entry was collected. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..96  

atmfM4CellProtoHistSuspect 1.3.6.1.4.1.353.100.1.16.1.2
If true, the statistics in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

atmfM4CellProtoHistElapsedTime 1.3.6.1.4.1.353.100.1.16.1.3
Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

atmfM4CellProtoHistSupprIntvls 1.3.6.1.4.1.353.100.1.16.1.4
This attribute is non-zero only if the ATM NE is suppressing ATM Cell Protocol Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4CellProtoHistProtoErrors 1.3.6.1.4.1.353.100.1.16.1.5
The number of ATM cells dropped on this interface, due to an unrecognized field or set of fields in the ATM cell header, since the start of this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4CellProtoHistInOAMCells 1.3.6.1.4.1.353.100.1.16.1.6
The number of OAM cells received at this interface since the start of this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4CellProtoErrorTable 1.3.6.1.4.1.353.100.1.17
The ATM Forum M4 Cell Protocol Monitoring Error Log table. This table maintains a record of the last error of each type encountered on each interface, as a result of ATM Cell Protocol Monitoring.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4CellProtoErrorEntry

atmfM4CellProtoErrorEntry 1.3.6.1.4.1.353.100.1.17.1
An entry in the ATM Forum M4 Cell Protocol Monitoring Error Log table. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it for each error that has occurred since agent start-up.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4CellProtoErrorEntry  

atmfM4CellProtoErrorCode 1.3.6.1.4.1.353.100.1.17.1.1
Indicates the type of error for which this entry contains information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

atmfM4CellProtoErrorTime 1.3.6.1.4.1.353.100.1.17.1.2
Value of sysUpTime when the error occurred.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

atmfM4CellProtoErrorReason 1.3.6.1.4.1.353.100.1.17.1.3
The cell header abnormality type: the reason for discarding the ATM cell (i.e., unassigned VPI/VCI value or VPI/VCI value out of range.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

atmfM4CellProtoErrorVpi 1.3.6.1.4.1.353.100.1.17.1.4
The VPI value of the discarded cell.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..4096  

atmfM4CellProtoErrorVci 1.3.6.1.4.1.353.100.1.17.1.5
The VCI value of the discarded cell.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

atmfM4TcProtoCurrTable 1.3.6.1.4.1.353.100.1.18
The ATM Forum M4 TC Adaptor Protocol Monitoring Current Data table. This table maintains per-interface statistics for the fifteen-minute interval currently being collected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4TcProtoCurrEntry

atmfM4TcProtoCurrEntry 1.3.6.1.4.1.353.100.1.18.1
An entry in the ATM Forum M4 TC Adaptor Protocol Monitoring Current Data table. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4TcProtoCurrEntry  

atmfM4TcProtoCurrSuspect 1.3.6.1.4.1.353.100.1.18.1.1
If true, the statistics in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

atmfM4TcProtoCurrElapsedTime 1.3.6.1.4.1.353.100.1.18.1.2
Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

atmfM4TcProtoCurrSupprIntvls 1.3.6.1.4.1.353.100.1.18.1.3
This attribute is non-zero only if the ATM NE is suppressing ATM TC Adaptor Protocol Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4TcProtoCurrDiscardHECViol 1.3.6.1.4.1.353.100.1.18.1.4
The number of ATM cells discarded on this interface, due to an HEC violation, since the start of this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4TcProtoHistTable 1.3.6.1.4.1.353.100.1.19
The ATM Forum M4 TC Adaptor Protocol Monitoring History Data table. This table maintains per-interface statistics for previous fifteen-minute intervals.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4TcProtoHistEntry

atmfM4TcProtoHistEntry 1.3.6.1.4.1.353.100.1.19.1
An entry in the ATM Forum M4 TC Adaptor Protocol Monitoring History Data table. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it for each fifteen- minute interval in which statistics are collected for it.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4TcProtoHistEntry  

atmfM4TcProtoHistIndex 1.3.6.1.4.1.353.100.1.19.1.1
A number between 1 and 96, which identifies the interval for which the set of statistics in this entry was collected. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..96  

atmfM4TcProtoHistSuspect 1.3.6.1.4.1.353.100.1.19.1.2
If true, the statistics in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

atmfM4TcProtoHistElapsedTime 1.3.6.1.4.1.353.100.1.19.1.3
Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

atmfM4TcProtoHistSupprIntvls 1.3.6.1.4.1.353.100.1.19.1.4
This attribute is non-zero only if the ATM NE is suppressing ATM Cell Protocol Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4TcProtoHistDiscardHECViol 1.3.6.1.4.1.353.100.1.19.1.5
The number of ATM cells discarded on this interface, due to an HEC violation, since the start of this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4VpUpcNpcCurrTable 1.3.6.1.4.1.353.100.1.20
The ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VPL termination points. This table maintains per-TP statistics for the fifteen-minute interval currently being collected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VpUpcNpcCurrEntry

atmfM4VpUpcNpcCurrEntry 1.3.6.1.4.1.353.100.1.20.1
An entry in the ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VPL termination points. Each VPL Termination Point automatically has an entry in this table associated with it.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VpUpcNpcCurrEntry  

atmfM4VpUpcNpcCurrSuspect 1.3.6.1.4.1.353.100.1.20.1.1
If true, the statistics in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

atmfM4VpUpcNpcCurrElapsedTime 1.3.6.1.4.1.353.100.1.20.1.2
Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

atmfM4VpUpcNpcCurrSupprIntvls 1.3.6.1.4.1.353.100.1.20.1.3
This attribute is non-zero only if the ATM NE is suppressing UPC/NPC Disagreement Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4VpUpcNpcCurrDiscardedCells 1.3.6.1.4.1.353.100.1.20.1.4
The number of discarded cells due to combined CLP=0 and CLP=1 UPC/NPC policing.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4VpUpcNpcCurrDiscardedClp0 1.3.6.1.4.1.353.100.1.20.1.5
The number of discarded cells due to CLP=0 only UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4VpUpcNpcCurrPassedCells 1.3.6.1.4.1.353.100.1.20.1.6
The number of cells that have been successfully passed by the combined CLP=0 and CLP=1 UPC/NPC policing.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4VpUpcNpcCurrPassedClp0 1.3.6.1.4.1.353.100.1.20.1.7
The number of cells that have been successfully passed by the CLP=0 UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4VpUpcNpcHistTable 1.3.6.1.4.1.353.100.1.21
The ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VPL termination points. This table maintains per-interface statistics for previous fifteen-minute intervals.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VpUpcNpcHistEntry

atmfM4VpUpcNpcHistEntry 1.3.6.1.4.1.353.100.1.21.1
An entry in the ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VPL termination points. Each VPL Termination Point automatically has an entry in this table associated with it.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VpUpcNpcHistEntry  

atmfM4VpUpcNpcHistIndex 1.3.6.1.4.1.353.100.1.21.1.1
A number between 1 and 96, which identifies the interval for which the set of statistics in this entry was collected. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..96  

atmfM4VpUpcNpcHistSuspect 1.3.6.1.4.1.353.100.1.21.1.2
If true, the statistics in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

atmfM4VpUpcNpcHistElapsedTime 1.3.6.1.4.1.353.100.1.21.1.3
Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

atmfM4VpUpcNpcHistSupprIntvls 1.3.6.1.4.1.353.100.1.21.1.4
This attribute is non-zero only if the ATM NE is suppressing UPC/NPC Disagreement Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4VpUpcNpcHistDiscardedCells 1.3.6.1.4.1.353.100.1.21.1.5
The number of discarded cells due to combined CLP=0 and CLP=1 UPC/NPC policing.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4VpUpcNpcHistDiscardedClp0 1.3.6.1.4.1.353.100.1.21.1.6
The number of discarded cells due to CLP=0 only UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4VpUpcNpcHistPassedCells 1.3.6.1.4.1.353.100.1.21.1.7
The number of cells that have been successfully passed by the combined CLP=0 and CLP=1 UPC/NPC policing.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4VpUpcNpcHistPassedClp0 1.3.6.1.4.1.353.100.1.21.1.8
The number of cells that have been successfully passed by the CLP=0 UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4VcUpcNpcCurrTable 1.3.6.1.4.1.353.100.1.22
The ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VCL termination points. This table maintains per-TP statistics for the fifteen-minute interval currently being collected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VcUpcNpcCurrEntry

atmfM4VcUpcNpcCurrEntry 1.3.6.1.4.1.353.100.1.22.1
An entry in the ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VCL termination points. Each VCL Termination Point automatically has an entry in this table associated with it.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VcUpcNpcCurrEntry  

atmfM4VcUpcNpcCurrSuspect 1.3.6.1.4.1.353.100.1.22.1.1
If true, the statistics in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

atmfM4VcUpcNpcCurrElapsedTime 1.3.6.1.4.1.353.100.1.22.1.2
Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

atmfM4VcUpcNpcCurrSupprIntvls 1.3.6.1.4.1.353.100.1.22.1.3
This attribute is non-zero only if the ATM NE is suppressing UPC/NPC Disagreement Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4VcUpcNpcCurrDiscardedCells 1.3.6.1.4.1.353.100.1.22.1.4
The number of discarded cells due to combined CLP=0 and CLP=1 UPC/NPC policing.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4VcUpcNpcCurrDiscardedClp0 1.3.6.1.4.1.353.100.1.22.1.5
The number of discarded cells due to CLP=0 only UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4VcUpcNpcCurrPassedCells 1.3.6.1.4.1.353.100.1.22.1.6
The number of cells that have been successfully passed by the combined CLP=0 and CLP=1 UPC/NPC policing.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4VcUpcNpcCurrPassedClp0 1.3.6.1.4.1.353.100.1.22.1.7
The number of cells that have been successfully passed by the CLP=0 UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmfM4VcUpcNpcHistTable 1.3.6.1.4.1.353.100.1.23
The ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VCL termination points. This table maintains per-interface statistics for previous fifteen-minute intervals.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VcUpcNpcHistEntry

atmfM4VcUpcNpcHistEntry 1.3.6.1.4.1.353.100.1.23.1
An entry in the ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VCL termination points. Each VCL Termination Point automatically has an entry in this table associated with it.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VcUpcNpcHistEntry  

atmfM4VcUpcNpcHistIndex 1.3.6.1.4.1.353.100.1.23.1.1
A number between 1 and 96, which identifies the interval for which the set of statistics in this entry was collected. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..96  

atmfM4VcUpcNpcHistSuspect 1.3.6.1.4.1.353.100.1.23.1.2
If true, the statistics in this entry may be unreliable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

atmfM4VcUpcNpcHistElapsedTime 1.3.6.1.4.1.353.100.1.23.1.3
Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

atmfM4VcUpcNpcHistSupprIntvls 1.3.6.1.4.1.353.100.1.23.1.4
This attribute is non-zero only if the ATM NE is suppressing UPC/NPC Disagreement Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4VcUpcNpcHistDiscardedCells 1.3.6.1.4.1.353.100.1.23.1.5
The number of discarded cells due to combined CLP=0 and CLP=1 UPC/NPC policing.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4VcUpcNpcHistDiscardedClp0 1.3.6.1.4.1.353.100.1.23.1.6
The number of discarded cells due to CLP=0 only UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4VcUpcNpcHistPassedCells 1.3.6.1.4.1.353.100.1.23.1.7
The number of cells that have been successfully passed by the combined CLP=0 and CLP=1 UPC/NPC policing.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4VcUpcNpcHistPassedClp0 1.3.6.1.4.1.353.100.1.23.1.8
The number of cells that have been successfully passed by the CLP=0 UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

atmfM4TestTypes 1.3.6.1.4.1.353.100.1.24
OBJECT IDENTIFIER    

atmfM4TestOAMLoopbackSeg 1.3.6.1.4.1.353.100.1.24.1
This identifies an OAM Loopback Test on a VPL, VPC, VCL, or VCC termination point, using a segment OAM cell. The test type must have appended to it a code that uniquely identifies an intermediate point responsible for looping back the cell. If this is absent, the loopback is performed at the end of the segment or connection. E.g., the OID { atmfM4TestOAMLoopbackSeg 5 } identifies that the loopback should be performed at the intermediate point labeled 5.
Status: current Access: read-only
OBJECT-IDENTITY    

atmfM4TestOAMLoopbackE2E 1.3.6.1.4.1.353.100.1.24.2
This identifies an OAM Loopback Test on a VPL, VPC, VCL, or VCC termination point, using an end-to-end OAM cell.
Status: current Access: read-only
OBJECT-IDENTITY    

atmfM4VpTestTable 1.3.6.1.4.1.353.100.1.25
The ATM Forum M4 VP Termination Point Test table. This table allows tests to be run on VPL and VPC termination points. The operation of this table is entirely analogous to that of the ifTestTable in RFC 1573, except that the indexes into this table are different.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VpTestEntry

atmfM4VpTestEntry 1.3.6.1.4.1.353.100.1.25.1
An entry containing objects for invoking tests on a VPL or VPC termination point.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VpTestEntry  

atmfM4VpTestObject 1.3.6.1.4.1.353.100.1.25.1.1
Specifies whether the test applies to the VPL termination point with the specified VPI, or the VPC termination point.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER vplTp(1), vpcTp(2)  

atmfM4VpTestId 1.3.6.1.4.1.353.100.1.25.1.2
This object identifies the current invocation of the interface's test.
Status: current Access: read-write
OBJECT-TYPE    
  TestAndIncr  

atmfM4VpTestStatus 1.3.6.1.4.1.353.100.1.25.1.3
This object indicates whether or not some manager currently has the necessary 'ownership' required to invoke a test on this interface. A write to this object is only successful when it changes its value from 'notInUse(1)' to 'inUse(2)'. After completion of a test, the agent resets the value back to 'notInUse(1)'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notInUse(1), inUse(2)  

atmfM4VpTestType 1.3.6.1.4.1.353.100.1.25.1.4
A control variable used to start and stop operator- initiated interface tests. Most OBJECT IDENTIFIER values assigned to tests are defined elsewhere, in association with specific types of interface. However, this document assigns a value for a full- duplex loopback test, and defines the special meanings of the subject identifier: noTest OBJECT IDENTIFIER ::= { 0 0 } When the value noTest is written to this object, no action is taken unless a test is in progress, in which case the test is aborted. Writing any other value to this object is only valid when no test is currently in progress, in which case the indicated test is initiated. When read, this object always returns the most recent value that atmfM4VpTestType was set to. If it has not been set since the last initialization of the network management subsystem on the agent, a value of noTest is returned.
Status: current Access: read-write
OBJECT-TYPE    
  AutonomousType  

atmfM4VpTestResult 1.3.6.1.4.1.353.100.1.25.1.5
This object contains the result of the most recently requested test, or the value none(1) if no tests have been requested since the last reset. Note that this facility provides no provision for saving the results of one test when starting another, as could be required if used by multiple managers concurrently.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), success(2), inProgress(3), notSupported(4), unAbleToRun(5), aborted(6), failed(7)  

atmfM4VpTestCode 1.3.6.1.4.1.353.100.1.25.1.6
This object contains a code which contains more specific information on the test result, for example an error-code after a failed test. Error codes and other values this object may take are specific to the type of interface and/or test. The value may have the semantics of either the AutonomousType or RowPointer textual conventions as defined in RFC 1903 [15]. The identifier: testCodeUnknown OBJECT IDENTIFIER ::= { 0 0 } is defined for use if no additional result code is available.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

atmfM4VpTestOwner 1.3.6.1.4.1.353.100.1.25.1.7
The entity which currently has the 'ownership' required to invoke a test on this interface.
Status: current Access: read-write
OBJECT-TYPE    
  OwnerString  

atmfM4VcTestTable 1.3.6.1.4.1.353.100.1.26
The ATM Forum M4 VC Termination Point Test table. This table allows tests to be run on VCL and VCC termination points. The operation of this table is entirely analogous to that of the ifTestTable in RFC 1573, except that the indexes into this table are different.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4VcTestEntry

atmfM4VcTestEntry 1.3.6.1.4.1.353.100.1.26.1
An entry containing objects for invoking tests on a VCL or VCC termination point.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4VcTestEntry  

atmfM4VcTestObject 1.3.6.1.4.1.353.100.1.26.1.1
Specifies whether the test applies to the VCL termination point with the specified VPI and VCI values, or to the VCC termination point.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER vclTp(1), vccTp(2)  

atmfM4VcTestId 1.3.6.1.4.1.353.100.1.26.1.2
This object identifies the current invocation of the interface's test.
Status: current Access: read-write
OBJECT-TYPE    
  TestAndIncr  

atmfM4VcTestStatus 1.3.6.1.4.1.353.100.1.26.1.3
This object indicates whether or not some manager currently has the necessary 'ownership' required to invoke a test on this interface. A write to this object is only successful when it changes its value from 'notInUse(1)' to 'inUse(2)'. After completion of a test, the agent resets the value back to 'notInUse(1)'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notInUse(1), inUse(2)  

atmfM4VcTestType 1.3.6.1.4.1.353.100.1.26.1.4
A control variable used to start and stop operator- initiated interface tests. Most OBJECT IDENTIFIER values assigned to tests are defined elsewhere, in association with specific types of interface. However, this document assigns a value for a full- duplex loopback test, and defines the special meanings of the subject identifier: noTest OBJECT IDENTIFIER ::= { 0 0 } When the value noTest is written to this object, no action is taken unless a test is in progress, in which case the test is aborted. Writing any other value to this object is only valid when no test is currently in progress, in which case the indicated test is initiated. When read, this object always returns the most recent value that atmfM4VcTestType was set to. If it has not been set since the last initialization of the network management subsystem on the agent, a value of noTest is returned.
Status: current Access: read-write
OBJECT-TYPE    
  AutonomousType  

atmfM4VcTestResult 1.3.6.1.4.1.353.100.1.26.1.5
This object contains the result of the most recently requested test, or the value none(1) if no tests have been requested since the last reset. Note that this facility provides no provision for saving the results of one test when starting another, as could be required if used by multiple managers concurrently.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), success(2), inProgress(3), notSupported(4), unAbleToRun(5), aborted(6), failed(7)  

atmfM4VcTestCode 1.3.6.1.4.1.353.100.1.26.1.6
This object contains a code which contains more specific information on the test result, for example an error-code after a failed test. Error codes and other values this object may take are specific to the type of interface and/or test. The value may have the semantics of either the AutonomousType or RowPointer textual conventions as defined in RFC 1903 [15]. The identifier: testCodeUnknown OBJECT IDENTIFIER ::= { 0 0 } is defined for use if no additional result code is available.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

atmfM4VcTestOwner 1.3.6.1.4.1.353.100.1.26.1.7
The entity which currently has the 'ownership' required to invoke a test on this termination point.
Status: current Access: read-write
OBJECT-TYPE    
  OwnerString  

atmfM4EquipTable 1.3.6.1.4.1.353.100.1.28
The ATM Forum M4 Equipment table. This table augments the physical entity table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4EquipEntry

atmfM4EquipEntry 1.3.6.1.4.1.353.100.1.28.1
An entry in the ATM Forum M4 Equipment table. Each entry of this type represents a piece of equipment within the ATM NE that neither is nor accepts a replaceable plug- in unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4EquipEntry  

atmfM4EquipAdminStatus 1.3.6.1.4.1.353.100.1.28.1.1
Used by the adminstrator to lock and unlock the object.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmfM4EquipLocation 1.3.6.1.4.1.353.100.1.28.1.2
The specific or general location of the component.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

atmfM4EquipOperStatus 1.3.6.1.4.1.353.100.1.28.1.3
This attributes identifies whether or not the component is capable of performing its normal functions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), unknown(3)  

atmfM4EquipVendor 1.3.6.1.4.1.353.100.1.28.1.4
The vendor of the component.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

atmfM4EquipVersion 1.3.6.1.4.1.353.100.1.28.1.5
The version of the component.
Status: current Access: read-only
OBJECT-TYPE    
  AutonomousType  

atmfM4EquipUserLabel 1.3.6.1.4.1.353.100.1.28.1.6
A user-friendly name for the piece of equipment.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

atmfM4EquipAlarmSeverityIndex 1.3.6.1.4.1.353.100.1.28.1.7
An index into the alarm severity profile table, specifying the severity assignments for M4 alarms reported for this component.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

atmfM4EquipHolderTable 1.3.6.1.4.1.353.100.1.29
The ATM Forum M4 Equipment Holder table. This table augments the physical table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4EquipHolderEntry

atmfM4EquipHolderEntry 1.3.6.1.4.1.353.100.1.29.1
An entry in the ATM Forum M4 Equipment Holder table. Each entry of this type represents a component within the ATM NE that accepts a replaceable plug-in unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4EquipHolderEntry  

atmfM4EquipHolderType 1.3.6.1.4.1.353.100.1.29.1.1
The type of the component.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER rack(1), shelf(2), drawer(3), slot(4)  

atmfM4EquipHolderAcceptableTypes 1.3.6.1.4.1.353.100.1.29.1.2
The types of plug-in units that can be supported by the slot, separated by newline characters. This attribute shall be present only when the Equipment Holder represents a slot.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

atmfM4EquipHolderSlotStatus 1.3.6.1.4.1.353.100.1.29.1.3
This attributes identifies whether or not a plug-in unit is present in the slot. This attribute shall be present only when the Equipment Holder represents a slot.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER empty(1), full(2)  

atmfM4EquipHolderSwLoad 1.3.6.1.4.1.353.100.1.29.1.4
An index into the installed software table, specifying the software that is to be loaded into the plug-in unit whenever an automatic reload of software is needed. This attribute shall be present only when the Equipment Holder represents a slot.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

atmfM4PlugInUnitTable 1.3.6.1.4.1.353.100.1.30
The ATM Forum M4 Plug-In Unittable. This table augments the physical entity table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4PlugInUnitEntry

atmfM4PlugInUnitEntry 1.3.6.1.4.1.353.100.1.30.1
An entry in the ATM Forum M4 Plug-In Unit table. Each entry of this type represents a piece of equipment within the ATM NE that is inserted into and removed from an Equipment Holder.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4PlugInUnitEntry  

atmfM4PlugInUnitAdminStatus 1.3.6.1.4.1.353.100.1.30.1.1
Used by the adminstrator to lock and unlock the object.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmfM4PlugInUnitAvailStatus 1.3.6.1.4.1.353.100.1.30.1.2
Provides further information regarding the state of the component.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER available(1), inTest(2), failed(3), powerOff(4), notInstalled(5), offLine(6), dependency(7)  

atmfM4PlugInUnitOperStatus 1.3.6.1.4.1.353.100.1.30.1.3
This attributes identifies whether or not the component is capable of performing its normal functions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), unknown(3)  

atmfM4PlugInUnitVendor 1.3.6.1.4.1.353.100.1.30.1.4
The vendor of the component.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

atmfM4PlugInUnitVersion 1.3.6.1.4.1.353.100.1.30.1.5
The version of the component.
Status: current Access: read-only
OBJECT-TYPE    
  AutonomousType  

atmfM4PlugInUnitAlarmSeverityIndex 1.3.6.1.4.1.353.100.1.30.1.6
An index into the alarm severity profile table, specifying the severity assignments for M4 alarms reported for this component.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

atmfM4HwRunningSwTable 1.3.6.1.4.1.353.100.1.32
The ATM Forum M4 Hardware Unit/Running Software relationship. This table describes the software that is running on each hardware unit in the ATM NE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4HwRunningSwEntry

atmfM4HwRunningSwEntry 1.3.6.1.4.1.353.100.1.32.1
An entry in the ATM Forum M4 Hardware Unit/Running Software relationship table. Each entry of this type identifies an entry in the entPhysicalTable and one in the hrRunningSoftwareTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4HwRunningSwEntry  

atmfM4HwRunningSwHwIndex 1.3.6.1.4.1.353.100.1.32.1.1
The index, in the entPhysicalTable, of the containing hardware unit in this pair.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..2147483647  

atmfM4HwRunningSwIndex 1.3.6.1.4.1.353.100.1.32.1.2
A unique number within the context of the containing hardware unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..2147483647  

atmfM4HwRunningSwSwIndex 1.3.6.1.4.1.353.100.1.32.1.3
The index, in the hrRunningSwTable, of the software product represented by this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

atmfM4HwInstalledSwTable 1.3.6.1.4.1.353.100.1.33
The ATM Forum M4 Hardware Unit/Installed Software relationship. This table describes the software that is Installed on each hardware unit in the ATM NE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4HwInstalledSwEntry

atmfM4HwInstalledSwEntry 1.3.6.1.4.1.353.100.1.33.1
An entry in the ATM Forum M4 Hardware Unit/Installed Software relationship table. Each entry of this type identifies an entry in the physical entity table and one in the hrInstalledSoftwareTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4HwInstalledSwEntry  

atmfM4HwInstalledSwHwIndex 1.3.6.1.4.1.353.100.1.33.1.1
The index, in the entPhysical table, of the containing physical entity in this pair.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..2147483647  

atmfM4HwInstalledSwIndex 1.3.6.1.4.1.353.100.1.33.1.2
A unique number within the context of the containing hardware unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

atmfM4HwInstalledSwSwIndex 1.3.6.1.4.1.353.100.1.33.1.3
The index, in the hrInstalledSwTable, of the software product represented by this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

atmfM4HwSwAlarmSeverityIndex 1.3.6.1.4.1.353.100.1.33.1.4
An index into the alarm severity profile table, specifying the severity assignments for M4 alarms reported for this piece of software installed on the hardware unit.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

atmfM4AlarmSevDefault 1.3.6.1.4.1.353.100.1.34
The default severity value used for new profile index/trap ID pairs that have not yet been modified. This value is also used whenever an object's alarm severity profile index is set to 0.
Status: current Access: read-write
OBJECT-TYPE    
  AtmfM4AlarmSeverity  

atmfM4AlarmSevProfileIndexNext 1.3.6.1.4.1.353.100.1.35
This object contains an appropriate value to be used for atmfM4AlarmSevProfileIndex when creating entries in the atmfM4AlarmSevProfileTable. The value -1 indicates that no unassigned entries are available. To obtain the index value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index (or -1).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

atmfM4AlarmSevProfileTable 1.3.6.1.4.1.353.100.1.36
The ATM Forum M4 alarm severity profile table. This table specifies which profiles exist. Creating or deleting an entry in this table automatically creates or deletes the corresponding entries in the atmfM4AlarmSeverityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4AlarmSevProfileEntry

atmfM4AlarmSevProfileEntry 1.3.6.1.4.1.353.100.1.36.1
A group of severities, one for each alarm type in the communications alarm group.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4AlarmSevProfileEntry  

atmfM4AlarmSevProfileIndex 1.3.6.1.4.1.353.100.1.36.1.1
A number identifying this alarm severity profile.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

atmfM4AlarmSevProfileRowStatus 1.3.6.1.4.1.353.100.1.36.1.2
This object is used to create a new row or to delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

atmfM4AlarmSevTable 1.3.6.1.4.1.353.100.1.37
The ATM Forum M4 alarm severity table. This table associates profile index and trap ID pairs with severities to be used for M4 alarm traps that have occurred. (Note that this table does not apply to cleared alarms.)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4AlarmSevEntry

atmfM4AlarmSevEntry 1.3.6.1.4.1.353.100.1.37.1
An entry in this table associates an alarm severity profile index/trap ID pair with a severity. Deleting a particular profile's row in the alarm severity profile table deletes all rows in this table with the same profile index. Conceptually, rows corresponding to all possible trap ID's are created in this table when a new alarm severity profile is created, but the agent will return a default value except for those few traps for which values have been set.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4AlarmSevEntry  

atmfM4AlarmSevTrapId 1.3.6.1.4.1.353.100.1.37.1.1
The ID of the trap type to which this entry applies.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

atmfM4AlarmSeverity 1.3.6.1.4.1.353.100.1.37.1.2
The severity to be used for this trap type when the is selected. If no value for this object has ever been set since the corresponding profile was created, the agent should return the value of the object atmfM4AlarmSevDefault
Status: current Access: read-create
OBJECT-TYPE    
  AtmfM4AlarmSeverity  

atmfM4ForwardAllTraps 1.3.6.1.4.1.353.100.1.38
This is used as the value of the object atmfM4ForwardedTrapObject when traps from all objects are to be forwarded, or when there is only one object of the type that forwards the specified trap type.
Status: current Access: read-create
OBJECT-IDENTITY    

atmfM4TrapForwardingTable 1.3.6.1.4.1.353.100.1.39
The ATM Forum M4 Trap forwarding discriminator table. This table specifies which traps will be sent to which management system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4TrapForwardingEntry

atmfM4TrapForwardingEntry 1.3.6.1.4.1.353.100.1.39.1
Information about a group of traps to be sent to a particular IP address. A new entry must have values for all attributes that do not have default values before its RowStatus column can be set to active(1).
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4TrapForwardingEntry  

atmfM4TrapForwardingIndex 1.3.6.1.4.1.353.100.1.39.1.1
A unique number identifying the table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

atmfM4TrapForwardingDest 1.3.6.1.4.1.353.100.1.39.1.2
The IP address to which traps identified by this table entry should be sent.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

atmfM4ForwardedTrapId 1.3.6.1.4.1.353.100.1.39.1.3
The ID of the trap type to which this entry applies.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

atmfM4ForwardedTrapObject 1.3.6.1.4.1.353.100.1.39.1.4
The object to which this entry applies. By convention, this is the name of the first object in the row in the table referenced. The special value { 0 0 } indicates that traps of this type from all objects of the type that can generate it. It should also be used when traps from the ATM NE are to be specified.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

atmfM4TrapForwardingPort 1.3.6.1.4.1.353.100.1.39.1.5
The UDP port on the specified management system to which traps identified by this entry should be sent.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

atmfM4LowestForwardedSeverity 1.3.6.1.4.1.353.100.1.39.1.6
The lowest severity of traps of this type from the specified object that should be sent to this address. This object has significance only if the trap type specified has a severity associated with it
Status: current Access: read-create
OBJECT-TYPE    
  AtmfM4AlarmSeverity  

atmfM4ForwardedIndeterminate 1.3.6.1.4.1.353.100.1.39.1.7
When this object has the value TRUE, traps with indeterminate severity will be forwarded to the specified event. This object has significance only if the trap type specified has a severity associated with it
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

atmfM4TrapForwardingRowStatus 1.3.6.1.4.1.353.100.1.39.1.8
This object is used to create a new row or to delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

atmfM4TrapLogTable 1.3.6.1.4.1.353.100.1.40
The ATM Forum M4 Trap Agent log table. This table defines the trap logs currently maintained by the agent. The management system creates entries in this table to specify which types of traps, from which ATM network elements, should be logged. Deleting an entry in this table deletes all entries in the corresponding log.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4TrapLogEntry

atmfM4TrapLogEntry 1.3.6.1.4.1.353.100.1.40.1
Information about a single trap log.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4TrapLogEntry  

atmfM4TrapLogSrc 1.3.6.1.4.1.353.100.1.40.1.1
The IP address of the SNMP agent whose traps are stored in this log.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

atmfM4TrapLogType 1.3.6.1.4.1.353.100.1.40.1.2
The type of traps stored in this log.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER objectCreated(1), objectDeleted(2), configChange(3), stateChange(4), alarm(5)  

atmfM4TrapLogAdminStatus 1.3.6.1.4.1.353.100.1.40.1.3
The management system uses this object to stop and start the operations of this object.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmfM4TrapLogOperStatus 1.3.6.1.4.1.353.100.1.40.1.4
Indicates whether or not the log is capable of performing its normal operations.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), logFull(3)  

atmfM4TrapLogFullAction 1.3.6.1.4.1.353.100.1.40.1.5
Indicates the action that should be performed when no more log entries can be created due to a log-full condition. If the value of this object is wrap(2), each new log entry will cause the deletion of the oldest entry still in the log, for as long as the log is still full.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER halt(1), wrap(2)  

atmfM4TrapLogRowStatus 1.3.6.1.4.1.353.100.1.40.1.6
This object is used to create a new row or to delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

atmfM4LoggedTrapTable 1.3.6.1.4.1.353.100.1.41
The ATM Forum M4 Trap Agent logged trap table. This table is used to maintain the traps logged.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4LoggedTrapEntry

atmfM4LoggedTrapEntry 1.3.6.1.4.1.353.100.1.41.1
Information about a single trap in the log. Entries in this table are created automatically but can be deleted by the management system. Entries that represent 'alarm' log types are augmented by the atmfM4LoggedAlarmEntry table.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4LoggedTrapEntry  

atmfM4LoggedTrapIndex 1.3.6.1.4.1.353.100.1.41.1.1
A unique number identifying this entry in the log. When the maximum value for this object has been reached, it will wrap around to 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

atmfM4LoggedTrapTime 1.3.6.1.4.1.353.100.1.41.1.2
The time at which this trap was logged.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

atmfM4LoggedTrapID 1.3.6.1.4.1.353.100.1.41.1.3
The type of trap to which this entry applies. Together with the logged trap ID object, this object specifies the entity to which this logged trap referred.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

atmfM4LoggedTrapObject 1.3.6.1.4.1.353.100.1.41.1.4
The object to which this entry applies. By convention, this is the name of the first object in the row in the table referenced. Together with the logged trap ID object, this object specifies the entity to which this logged trap referred. The special value { 0 0 } indicates that the trap refers to the ATM NE entity itself.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

atmfM4LoggedTrapRowStatus 1.3.6.1.4.1.353.100.1.41.1.5
This object is used to delete an existing row in the table. Note that the only value to which a management system can set this object is destroy(6).
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

atmfM4LoggedAlarmTable 1.3.6.1.4.1.353.100.1.42
The ATM Forum M4 Trap Agent logged alarm trap table. This table is used to maintain extra information for logged traps that represent alarm types.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmfM4LoggedAlarmEntry

atmfM4LoggedAlarmEntry 1.3.6.1.4.1.353.100.1.42.1
Information about the alarm-specific attributes of a single trap in the log.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmfM4LoggedAlarmEntry  

atmfM4LoggedAlarmSeverity 1.3.6.1.4.1.353.100.1.42.1.1
The perceived severity of the alarm, as specified by the agent that generated it.
Status: current Access: read-only
OBJECT-TYPE    
  AtmfM4AlarmLogSeverity  

atmfM4LoggedAlarmBackedUp 1.3.6.1.4.1.353.100.1.42.1.2
If the value of this object is true, the agent reported in this trap that the failed object had been backed up. This object is only present if it was included in the alarm trap corresponding to this log entry.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

atmfM4LoggedAlarmBUObject 1.3.6.1.4.1.353.100.1.42.1.3
Indicates the object that provided back-up services to the failed object. This object is only present if it was included in the alarm trap corresponding to this log entry.
Status: current Access: read-only
OBJECT-TYPE    
  RowPointer  

atmfM4LoggedAlarmSpecificProb 1.3.6.1.4.1.353.100.1.42.1.4
Indicates further refinements to the problem identified by the alarm type. If more than one specific problem is described in this object, the problem descriptions are separated by newline characters. This object is only present if it was included in the alarm trap corresponding to this log entry.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

atmfM4LoggedAlarmRepairAct 1.3.6.1.4.1.353.100.1.42.1.5
Indicates proposed repair actions reported by the agent for the the problem identified by the alarm. If more than one action is described in this object, the problem descriptions are separated by newline characters. This object is only present if it was included in the alarm trap corresponding to this log entry.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

atmfM4TrapAlarmSeverity 1.3.6.1.4.1.353.100.1.43
The perceived severity of the alarm, as specified by the agent that generated it.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  AtmfM4AlarmLogSeverity  

atmfM4TrapAlarmBackedUp 1.3.6.1.4.1.353.100.1.44
If the value of this object is true, the failed object has been backed up.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TruthValue  

atmfM4TrapAlarmBUObject 1.3.6.1.4.1.353.100.1.45
Indicates the object that provided back-up services to the failed object.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  RowPointer  

atmfM4TrapAlarmSpecificProb 1.3.6.1.4.1.353.100.1.46
Indicates further refinements to the problem identified by the alarm type. If more than one specific problem is described in this object, the problem descriptions are separated by newline characters.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

atmfM4TrapAlarmRepairAct 1.3.6.1.4.1.353.100.1.47
Indicates proposed repair actions reported by the agent for the the problem identified by the alarm. If more than one action is described in this object, the problem descriptions are separated by newline characters.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

atmfM4IfAisAlarm 1.3.6.1.4.1.353.100.2.1
Indicates that an AIS alarm condition has occurred on the physical path TP associated with the specified interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4IfLcdAlarm 1.3.6.1.4.1.353.100.2.2
Indicates that an LCD (Loss of Cell Delineation) condition has occurred on the TC Adatpr associated with the specified interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4IfLofAlarm 1.3.6.1.4.1.353.100.2.3
Indicates that an LOF (Loss of Frame) condition has occurred on the physical path TP associated with the specified interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4IfLopAlarm 1.3.6.1.4.1.353.100.2.4
Indicates that an LOP (Loss of Pointer) condition has occurred on the physical path TP associated with the specified interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4IfLosAlarm 1.3.6.1.4.1.353.100.2.5
Indicates that an LOS (Loss of Signal) condition has occurred on the physical path TP associated with the specified interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4IfPayloadMismatchAlarm 1.3.6.1.4.1.353.100.2.6
Indicates that a payload type mismatch condition has occurred on the physical path TP associated with the specified interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4IfXmissionErrAlarm 1.3.6.1.4.1.353.100.2.7
Indicates that an transmission error condition has occurred on the physical path TP associated with the specified interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4IfPathTraceMismatchAlarm 1.3.6.1.4.1.353.100.2.8
Indicates that path trace mismatch condition has occurred on the physical path TP associated with the specified interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4IfRdiAlarm 1.3.6.1.4.1.353.100.2.9
Indicates that an RDI (Remote Defect Indication) condition has occurred on the physical path TP associated with the specified interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4IfSignalLabelMismatchAlarm 1.3.6.1.4.1.353.100.2.10
Indicates that a signal label mismatch has occurred on the physical path TP associated with the specified interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwLineCardAlarm 1.3.6.1.4.1.353.100.2.23
Indicates that a line-card problem condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwPowerAlarm 1.3.6.1.4.1.353.100.2.25
Indicates that a power problem alarm condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwPIUnitMissingAlarm 1.3.6.1.4.1.353.100.2.29
Indicates that a plug-in unit missing condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwPIUnitProbAlarm 1.3.6.1.4.1.353.100.2.30
Indicates that a plug-in unit problem condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwPIUnitMismatchAlarm 1.3.6.1.4.1.353.100.2.31
Indicates that a plug-in unit type mismatch condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwTimingProbAlarm 1.3.6.1.4.1.353.100.2.32
Indicates that a timing problem alarm condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwSwDownloadFailAlarm 1.3.6.1.4.1.353.100.2.39
Indicates that a software download failure has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwVersionMismatchAlarm 1.3.6.1.4.1.353.100.2.40
Indicates that a version mismatch condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwFanFailAlarm 1.3.6.1.4.1.353.100.2.41
Indicates that a cooling fan failure condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwHighTempAlarm 1.3.6.1.4.1.353.100.2.44
Indicates that a high temperature condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4SwVersionMismatchAlarm 1.3.6.1.4.1.353.100.2.45
Indicates that a version mismatch condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwUnitUp 1.3.6.1.4.1.353.100.2.54
Indicates that the operational state of the specified hardware unit has transitioned to 'up'.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwUnitDown 1.3.6.1.4.1.353.100.2.55
Indicates that the operational state of the specified hardware unit has transitioned to 'down'.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4AtmCellIfCreated 1.3.6.1.4.1.353.100.2.56
Indicates that an ATM cell layer interface has just been created on the interface.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4AtmCellIfDeleted 1.3.6.1.4.1.353.100.2.57
Indicates that the ATM cell layer interface has just been deleted.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwUnitCreated 1.3.6.1.4.1.353.100.2.66
Indicates that the specified hardware unit has been installed at the specified location.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4HwUnitDeleted 1.3.6.1.4.1.353.100.2.67
Indicates that the specified hardware unit has been removed or de-instaleld from the specified location.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4IfChanged 1.3.6.1.4.1.353.100.2.70
Indicates that the configuration of the interface has been changed.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

atmfM4Groups 1.3.6.1.4.1.353.100.3.1
OBJECT IDENTIFIER    

atmfM4Compliances 1.3.6.1.4.1.353.100.3.2
OBJECT IDENTIFIER    

atmfM4Compliance 1.3.6.1.4.1.353.100.3.2.1
The compliance statements are listed as a set up conformance units that correspond to each table. Support for all tables is mandatory.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

atmfM4General 1.3.6.1.4.1.353.100.3.1.1
NE high level objects
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4PhysPathTpGroup 1.3.6.1.4.1.353.100.3.1.2
The ATM Forum M4 interface Configuration table extensions for the physical path termination point
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4TcAdaptorGroup 1.3.6.1.4.1.353.100.3.1.3
The ATM Forum M4 interface Configuration table extensions for the TC Adaptor.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4AtmLayerGroup 1.3.6.1.4.1.353.100.3.1.4
The ATM Forum M4 interface Configuration table extensions for the ATM cell layer.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VplGroup 1.3.6.1.4.1.353.100.3.1.5
The ATM Forum M4 VPL Termination Point Configuration table extensions.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VclGroup 1.3.6.1.4.1.353.100.3.1.6
The ATM Forum M4 VCL Termination Point Configuration table extensions.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VpXConnGroup 1.3.6.1.4.1.353.100.3.1.7
The ATM Forum M4 VP Cross-Connect Configuration table extensions.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VcXConnGroup 1.3.6.1.4.1.353.100.3.1.8
The ATM Forum M4 VC Cross-Connect Configuration table extensions.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VpNextVpiGroup 1.3.6.1.4.1.353.100.3.1.9
The ATM Forum M4 VP Next-VPI value table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VcNextVciGroup 1.3.6.1.4.1.353.100.3.1.10
The ATM Forum M4 VC Next-VCI value table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4CellProtoCurrGroup 1.3.6.1.4.1.353.100.3.1.11
The ATM Forum M4 Cell Protocol Monitoring Current Data table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4CellProtoHistGroup 1.3.6.1.4.1.353.100.3.1.12
The ATM Forum M4 Cell Protocol Monitoring History Data table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4CellProtoErrorGroup 1.3.6.1.4.1.353.100.3.1.13
The ATM Forum M4 Cell Protocol Monitoring Error Log table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4TcProtoCurrGroup 1.3.6.1.4.1.353.100.3.1.14
The ATM Forum M4 TC Adaptor Protocol Monitoring Current Data table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4TcProtoHistGroup 1.3.6.1.4.1.353.100.3.1.15
The ATM Forum M4 TC Adaptor Protocol Monitoring History Data table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VpUpcNpcCurrGroup 1.3.6.1.4.1.353.100.3.1.16
The ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VPL termination points.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VpUpcNpcHistGroup 1.3.6.1.4.1.353.100.3.1.17
The ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VPL termination points.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VcUpcNpcCurrGroup 1.3.6.1.4.1.353.100.3.1.18
The ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VCL termination points
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VcUpcNpcHistGroup 1.3.6.1.4.1.353.100.3.1.19
The ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VCL termination points.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VpTestGroup 1.3.6.1.4.1.353.100.3.1.20
The ATM Forum M4 VP Termination Point Test table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4VcTestGroup 1.3.6.1.4.1.353.100.3.1.21
The ATM Forum M4 VC Termination Point Test table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4EquipGroup 1.3.6.1.4.1.353.100.3.1.22
The ATM Forum M4 Equipment table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4EquipHolderGroup 1.3.6.1.4.1.353.100.3.1.23
The ATM Forum M4 Equipment Holder table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4PlugInUnitGroup 1.3.6.1.4.1.353.100.3.1.24
The ATM Forum M4 Plug-In Unit table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4HwRunningSwGroup 1.3.6.1.4.1.353.100.3.1.25
The ATM Forum M4 Hardware Unit/Running Software table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4HwInstalledSwGroup 1.3.6.1.4.1.353.100.3.1.26
The ATM Forum M4 Hardware Unit/Installed Software table
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4AlarmSevGroup 1.3.6.1.4.1.353.100.3.1.27
Alarm handling objects
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4TrapForwardingGroup 1.3.6.1.4.1.353.100.3.1.28
Trap forwarding table
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4TrapLogGroup 1.3.6.1.4.1.353.100.3.1.29
The ATM Forum M4 Trap Agent log table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4LoggedTrapGroup 1.3.6.1.4.1.353.100.3.1.30
The ATM Forum M4 Trap Agent logged trap table.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

atmfM4LoggedAlarmGroup 1.3.6.1.4.1.353.100.3.1.31
The ATM Forum M4 Trap Agent logged alarm trap table.
Status: current Access: accessible-for-notify
OBJECT-GROUP