ATM-FORUM-AUTO-CONFIG

File: ATM-FORUM-AUTO-CONFIG.mib (59258 bytes)

Imported modules

SNMPv2-TC	SNMPv2-SMI	ATM-FORUM-TC-MIB
RFC-1215

Imported symbols

DisplayString	RowPointer	OBJECT-TYPE
atmForum	atmForumUni	TRAP-TYPE

Defined Types

AtmfAtmServiceTypeEntry
SEQUENCE
	atmfAtmServiceTypeIndex	INTEGER
	atmfAtmServiceProviderName	DisplayString
	atmfAtmServiceName	DisplayString
	atmfAtmServiceSubName	DisplayString
	atmfAtmServiceClient	DisplayString
	atmfAtmServiceTMCategory	INTEGER
	atmfAtmServiceTMConformanceDef	INTEGER

AtmfAtmServiceConnInfoEntry
SEQUENCE
	atmfAtmServicePortIndex	INTEGER
	atmfAtmServiceVpi	INTEGER
	atmfAtmServiceVci	INTEGER
	atmfAtmServiceSignalId	INTEGER
	atmfAtmServiceConnServiceIndex	INTEGER
	atmfAtmServiceConnName	DisplayString
	atmfAtmServiceConnAALType	INTEGER
	atmfAtmServiceConnAALIndex	INTEGER

AtmfAAL1ProfileEntry
SEQUENCE
	atmfAAL1ProfileIndex	INTEGER
	atmfAAL1Subtype	INTEGER
	atmfAAL1CBRRate	INTEGER
	atmfAAL1ClkRecoveryType	INTEGER
	atmfAAL1FEC	INTEGER
	atmfAAL1SDT	INTEGER
	atmfAAL1PartiallyFilledCells	INTEGER
	atmfAAL1CellLossIntegrPeriod	INTEGER

AtmfAAL34ProfileEntry
SEQUENCE
	atmfAAL34ProfileIndex	INTEGER
	atmfAAL34MaxCpcsSduSizeForward	INTEGER
	atmfAAL34MaxCpcsSduSizeBackward	INTEGER
	atmfAAL34MIDRangeLow	INTEGER
	atmfAAL34MIDRangeHigh	INTEGER
	atmfAAL34AALMode	INTEGER
	atmfAAL34SscsType	INTEGER

AtmfAAL5ProfileEntry
SEQUENCE
	atmfAAL5ProfileIndex	INTEGER
	atmfAAL5MaxCpcsSduSizeForward	INTEGER
	atmfAAL5MaxCpcsSduSizeBackward	INTEGER
	atmfAAL5AALMode	INTEGER
	atmfAAL5SscsType	INTEGER

AtmfAAL2CommonProfileEntry
SEQUENCE
	atmfAAL2ProfileIndex	INTEGER
	atmfAAL2ApplicationIdentifier	INTEGER
	atmfAAL2ConfigResponsibility	INTEGER
	atmfAAL2CpsMaxMultiplexedChannels	INTEGER
	atmfAAL2CpsMaxSduLength	INTEGER
	atmfAAL2SscsMaxSssarSduLength	INTEGER
	atmfAAL2SscsSstedStatus	INTEGER
	atmfAAL2SscsSsadtStatus	INTEGER
	atmfAAL2SscsServiceCategory	INTEGER
	atmfAAL2SscsAudioServiceTransport	INTEGER
	atmfAAL2SscsProfileSource	INTEGER
	atmfAAL2SscsIeeeOui	INTEGER
	atmfAAL2SscsPredefinedProfileIdentifier	INTEGER
	atmfAAL2SscsPcmEncoding	INTEGER
	atmfAAL2SscsFaxDemodulationTransport	INTEGER
	atmfAAL2SscsCasSignalingTransport	INTEGER
	atmfAAL2SscsDtmfDigitPacketTransport	INTEGER
	atmfAAL2SscsMfR1DigitPacketTransport	INTEGER
	atmfAAL2SscsMfR2DigitPacketTransport	INTEGER
	atmfAAL2SscsCircuitModeDataTransport	INTEGER
	atmfAAL2SscsCircuitModeDataNumChannels	INTEGER
	atmfAAL2SscsFrameModeDataTransport	INTEGER
	atmfAAL2SscsFrameModeDataMaxLength	INTEGER
	atmfAAL2SscopSduLength	INTEGER
	atmfAAL2SscopUuFieldLength	INTEGER

AtmfAAL2TrunkingProfileEntry
SEQUENCE
	atmfAAL2Vcci	INTEGER
	atmfAAL2SignalingVcci	INTEGER

AtmfAAL2LESProfileEntry
SEQUENCE
	atmfAAL2CpsCIDLowerLimit	INTEGER
	atmfAAL2CpsCIDUpperLimit	INTEGER
	atmfAAL2CpsOptimisation	INTEGER

AtmfAtmServiceConnInfoExtensionEntry
SEQUENCE
	atmfAtmServicePhyMacIdentifier	INTEGER

AtmfAtmServiceTypeExtensionEntry
SEQUENCE
	atmfAtmServiceLayer2ProtocolId	OCTET STRING
	atmfAtmServiceLayer3ProtocolId	OCTET STRING

AtmfAAL5ProfileExtensionEntry
SEQUENCE
	atmfAAL5Vcci	INTEGER

Defined Values

atmfAutoConfigGroup		1.3.6.1.4.1.353.2.12
OBJECT IDENTIFIER

atmfAtmServiceTypeTable		1.3.6.1.4.1.353.2.12.1
The ATM Forum ILMI Auto Configuration Extension ATM Service Type Information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAtmServiceTypeEntry

atmfAtmServiceTypeEntry		1.3.6.1.4.1.353.2.12.1.1
An entry in the service type table describes the reference information about a service that may be associated with individual ATM connections for the purpose of auto- configuration. This information describe the name and sub- name of the service, the client layer protocol using the ATM service, the TM 4.0 service category, and the TM 4.0 conformance definition.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAtmServiceTypeEntry

atmfAtmServiceTypeIndex		1.3.6.1.4.1.353.2.12.1.1.1
A number between which identifies the entry in the Service Type Table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2147483647

atmfAtmServiceProviderName		1.3.6.1.4.1.353.2.12.1.1.2
This string identifies the name of the service provider for the service described in this profile. The value of this attribute should not set to NULL.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

atmfAtmServiceName		1.3.6.1.4.1.353.2.12.1.1.3
This string identifies the name of the service described in this profile. The value of this attribute should not be set to NULL.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

atmfAtmServiceSubName		1.3.6.1.4.1.353.2.12.1.1.4
This string identifies the sub-name of the service described in this profile. A Service may have zero or more sub-names, each with its own service type profile.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

atmfAtmServiceClient		1.3.6.1.4.1.353.2.12.1.1.5
This string identifies the client protocol of the service described in this profile. A Service (sub-service) may have zero or more described client, each with its own service type profile.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

atmfAtmServiceTMCategory		1.3.6.1.4.1.353.2.12.1.1.6
The TM 4.0 Service category used for this service type. Indicates CBR, rt-VBR, nrt-VBR, ABR, UBR, (or GFR)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), cbr(2), rtVbr(3), nrtVbr(4), abr(5), ubr(6), gfr(7)

atmfAtmServiceTMConformanceDef		1.3.6.1.4.1.353.2.12.1.1.7
The TM 4.1 conformance definition used for this service type. Indicates CBR.1, VBR.1, VBR.2, VBR.3, UBR.1, UBR.2, ABR, GFR.1, or GFR.2.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), other(1), cbr1(2), vbr1(3), vbr2(4), vbr3(5), ubr1(6), ubr2(7), abr(8), gfr1(9), gfr2(10)

atmfAtmServiceConnInfoTable		1.3.6.1.4.1.353.2.12.2
The ATM Forum ILMI Auto Configuration Extension ATM Service Connection Information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAtmServiceConnInfoEntry

atmfAtmServiceConnInfoEntry		1.3.6.1.4.1.353.2.12.2.1
An entry in the service connection information table describes the ATM connection that provides a service across an ATM interface. The connection is identified by port and VPI/VCI value. Information about the connection includes the connection type (VP or VC, SVC or PVC), and the association of the connection with a service type. Specific connection information, such as traffic descriptors, should be accessed in the atmfVpc and atmfVcc tables defined in ILMI.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAtmServiceConnInfoEntry

atmfAtmServicePortIndex		1.3.6.1.4.1.353.2.12.2.1.1
The value of 0 (zero)has the special meaning of identifying the ATM Interface over which this ILMI message was received.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..2147483647

atmfAtmServiceVpi		1.3.6.1.4.1.353.2.12.2.1.2
The VPI value of the ATM service connection at the local ATM interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..255

atmfAtmServiceVci		1.3.6.1.4.1.353.2.12.2.1.3
The VCI value of the ATM service connection at the local ATM interface. If the atmfAtmServiceSignalId indicates that the connection is a VP connection, the value of this attribute shall be set to 0 (zero) and any meaning of this attribute ignored.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

atmfAtmServiceSignalId		1.3.6.1.4.1.353.2.12.2.1.4
This attribute represents the characteristic information of the layer network domain. It may be set to either VC characteristic information (vcCI) or VP characteristic information (vpCI).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	vcCI(0), vpCI(1)

atmfAtmServiceConnServiceIndex		1.3.6.1.4.1.353.2.12.2.1.5
The value of this object identifies the row in the atmfAtmServiceTypeTable. This entry represents the association between an ATM service connection and an ATM service type profile that describes it.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAtmServiceConnName		1.3.6.1.4.1.353.2.12.2.1.6
This string identifies the name of the service connection. The value of this attribute may be set to NULL.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

atmfAtmServiceConnAALType		1.3.6.1.4.1.353.2.12.2.1.7
Describes the AAL Type of the ATM service connection. A value of none indicates that no AAL is used. The AAL types include AAL1, AAL 3/4, and AAL 5. The value other may be a user-defined AAL type. The unknown type indicates that the AAL type cannot be determined.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), aal1(1), aal34(2), aal5(3), other(4), unknown(5), aal2(6)

atmfAtmServiceConnAALIndex		1.3.6.1.4.1.353.2.12.2.1.8
The value of this object identifies the row in the atmfAAL1ProfileTable for AAL 1 connection, the atmfAAL34ProfileTable for AAL3/4 connection, and the atmfAAL5ProfileTable for AAL 5 connections. This entry represents the association between an ATM service connection and an ATM Adaptation Layer profile that describes it.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAAL1ProfileTable		1.3.6.1.4.1.353.2.12.3
The ATM Forum ILMI Auto Configuration Extension AAL1 Profile Information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAAL1ProfileEntry

atmfAAL1ProfileEntry		1.3.6.1.4.1.353.2.12.3.1
An entry in the AAL1 Profile table provides data that describes the AAL1 processing function.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAAL1ProfileEntry

atmfAAL1ProfileIndex		1.3.6.1.4.1.353.2.12.3.1.1
A number between which identifies the entry in the AAL1 Profile Table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2147483647

atmfAAL1Subtype		1.3.6.1.4.1.353.2.12.3.1.2
This attribute describes AAL type 1 subtype used by the CBR service application (e.g. 64 KBPS voice band signal transport, circuit transport).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	null(0), voiceBand(1), circuitEmulationSynchronous(2), circuitEmulationAsynchronous(3), highQualityAuto(4), video(5)

atmfAAL1CBRRate		1.3.6.1.4.1.353.2.12.3.1.3
This attribute describes the rate of the CBR service supported by the AAL.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAAL1ClkRecoveryType		1.3.6.1.4.1.353.2.12.3.1.4
This attribute indicates whether the clock recovery type is synchronous, asynchronous-SRTS(Synchronous Residual Time Stamp), or asynchronous-Adaptive Clock Recovery.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	synchronous(0), srts(1), adaptive(2)

atmfAAL1FEC		1.3.6.1.4.1.353.2.12.3.1.5
This attribute indicates the FEC method: no FEC, FEC for Loss Sensitive Signal Transport, or FEC for Delay Sensitive Signal Transport.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noFEC(0), lossSensitiveSignalFEC(1), delaySensitiveSignalFEC(2)

atmfAAL1SDT		1.3.6.1.4.1.353.2.12.3.1.6
This attribute indicates whether Structured Data Transfer (SDT) has been configured at the AAL. A value of TRUE means SDT has been selected. This attribute value can be set to TRUE only when the Forward Error Correction Type attribute equals noFEC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	false(0), true(1)

atmfAAL1PartiallyFilledCells		1.3.6.1.4.1.353.2.12.3.1.7
This attribute identifies the number of leading octets in use.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAAL1CellLossIntegrPeriod		1.3.6.1.4.1.353.2.12.3.1.8
This attribute represents the time in milliseconds for the cell loss integration period. If cells are lost for this period of time, the Interworking VCC Termination Point entity will generate a cell starvation alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAAL34ProfileTable		1.3.6.1.4.1.353.2.12.4
The ATM Forum ILMI Auto Configuration Extension AAL3/4 Profile Information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAAL34ProfileEntry

atmfAAL34ProfileEntry		1.3.6.1.4.1.353.2.12.4.1
An entry in the AAL34 Profile table provides data that describes the AAL3/4 processing function.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAAL34ProfileEntry

atmfAAL34ProfileIndex		1.3.6.1.4.1.353.2.12.4.1.1
A number between which identifies the entry in the AAL3/4 Profile Table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2147483647

atmfAAL34MaxCpcsSduSizeForward		1.3.6.1.4.1.353.2.12.4.1.2
This attribute represents the maximum CPCS_PDU size that will be transmitted over the connection in both the incoming (forward) direction of transmission.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atmfAAL34MaxCpcsSduSizeBackward		1.3.6.1.4.1.353.2.12.4.1.3
This attribute represents the maximum CPCS_PDU size that will be transmitted over the connection in both the outgoing (backward) direction of transmission.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atmfAAL34MIDRangeLow		1.3.6.1.4.1.353.2.12.4.1.4
This attribute represents the low value of MID supported at the AAL for the supporting VCC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..66536

atmfAAL34MIDRangeHigh		1.3.6.1.4.1.353.2.12.4.1.5
This attribute represents the high value of MID supported at the AAL for the supporting VCC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..66536

atmfAAL34AALMode		1.3.6.1.4.1.353.2.12.4.1.6
This attribute indicates whether the AAL for the supporting VCC is operating in message mode or streaming mode, assured or unassured.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	messageAssured(0), messageUnassured(1), streamingAssured(2), streamingUnassured(3)

atmfAAL34SscsType		1.3.6.1.4.1.353.2.12.4.1.7
This attribute identifies the SSCS type for the AAL. Valid values are NULL, Data SSCS based on SSCOP (assured operation), Data SSCS based on SSCOP (non-assured operation), or Frame Relay SSCS
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	null(0), dataAssured(1), dataNonAssured(2), frameRelay(3)

atmfAAL5ProfileTable		1.3.6.1.4.1.353.2.12.5
The ATM Forum ILMI Auto Configuration Extension AAL5 Profile Information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAAL5ProfileEntry

atmfAAL5ProfileEntry		1.3.6.1.4.1.353.2.12.5.1
An entry in the AAL5 Profile table provides data that describes the AAL5 processing function.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAAL5ProfileEntry

atmfAAL5ProfileIndex		1.3.6.1.4.1.353.2.12.5.1.1
A number between which identifies the entry in the AAL5 Profile Table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..2147483647

atmfAAL5MaxCpcsSduSizeForward		1.3.6.1.4.1.353.2.12.5.1.2
This attribute represents the maximum CPCS_PDU size that will be transmitted over the connection in both the incoming (forward) direction of transmission.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atmfAAL5MaxCpcsSduSizeBackward		1.3.6.1.4.1.353.2.12.5.1.3
This attribute represents the maximum CPCS_PDU size that will be transmitted over the connection in both the outgoing (backward) direction of transmission.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atmfAAL5AALMode		1.3.6.1.4.1.353.2.12.5.1.4
This attribute indicates whether the AAL for the supporting VCC is operating in message mode or streaming mode, assured or unassured.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	messageAssured(0), messageUnassured(1), streamingAssured(2), streamingUnassured(3)

atmfAAL5SscsType		1.3.6.1.4.1.353.2.12.5.1.5
This attribute identifies the SSCS type for the AAL. Valid values are NULL, Data SSCS based on SSCOP (assured operation), Data SSCS based on SSCOP (non-assured operation), or Frame Relay SSCS
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	null(0), dataAssured(1), dataNonAssured(2), frameRelay(3)

atmfAAL2CommonProfileTable		1.3.6.1.4.1.353.2.12.6
The ATM Forum ILMI Auto Configuration Extension AAL2 Profile Information. This table contains AAL2 parameters that are common to all AAL2 applications. These parameters are taken from I.363.2, I.366.1 and I.366.2
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAAL2CommonProfileEntry

atmfAAL2CommonProfileEntry		1.3.6.1.4.1.353.2.12.6.1
An atmfAAL2CommonProfileEntry provides AAL2 common parameters of operation that are to be used by the PVC associated with this entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAAL2CommonProfileEntry

atmfAAL2ProfileIndex		1.3.6.1.4.1.353.2.12.6.1.1
A number which uniquely identifies the entry in the AAL2 Profile Table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAAL2ApplicationIdentifier		1.3.6.1.4.1.353.2.12.6.1.2
The application identifier specifies which AAL2 application is using the PVC. In addition it specifies protocol combinations to be used on AAL2 channels between IWFs, i.e. it implicitly configures the use of I.366.1 or I.366.2 for bearer and signalling AAL2 channels. The value of this object should be one of those values given in the administered list of AppIds for AAL2 Applications in section 5 of the ATM Forum document of well-known addresses and assigned codes which can be located at vhttp://www.atmforum.com/atmforum/specs/public_assigned_codes.pdf.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAAL2ConfigResponsibility		1.3.6.1.4.1.353.2.12.6.1.3
This object identifies which management channel is responsible for AAL2 provisioning and auto-configuration. The user-side IME must check the value of this parameter first before configuring the AAL2 for the PVC to determine whether or not this responsibility lies with ILMI. ilmi - if this is selected then the user-side IME must use the AAL2 Profile defined in this entry and associated AAL2 Profile extension table entry to auto-configure the AAL2 for the PVC. lesEoc - if this is selected then the user-side IME must not auto-configure the AAL2 using ILMI. The AAL2 Profile parameters do not need to be provisioned by the network- side IME and with the exception of this object the AAL2 profile parameters in the ILMI MIB are not applicable. The Loop Emulation Service Embedded Operations Channel (LES EOC) shall be used to provision the AAL2 for the PVC. The start-up AAL2 parameters for this PVC must assume the default values specified in the af-vmoa-0145.000 MIB such that the LES EOC is operational. other - if this is selected then the user-side IME must not auto-configure the AAL2 using ILMI. The AAL2 Profile parameters do not need to be provisioned by the network- side IME and with the exception of this object the AAL2 profile parameters in the ILMI MIB are not applicable. Another mechanism will be used to provision the AAL2 at the ATU-R for the PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ilmi(1), lesEoc(2), other(3)

atmfAAL2CpsMaxMultiplexedChannels		1.3.6.1.4.1.353.2.12.6.1.4
Maximum number of multiplexed channels.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..255

atmfAAL2CpsMaxSduLength		1.3.6.1.4.1.353.2.12.6.1.5
Maximum CPS-SDU size given in octets. This parameter is bidirectional, i.e. its value applies to both directions of the AAL2 connection.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	45 \| 64

atmfAAL2SscsMaxSssarSduLength		1.3.6.1.4.1.353.2.12.6.1.6
This is the maximum size and SSSAR-SDU can take as defined in I.366.1. This parameter only applies to those AAL2 channels using I.366.1 SSSAR. This parameter is bidirectional, i.e its value applies to both directions of the AAL2 connection. Note that if the appID indicates Loop Emulation Service as the AAL2 application then the minimum allowable value of this parameter is 493.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65568

atmfAAL2SscsSstedStatus		1.3.6.1.4.1.353.2.12.6.1.7
This specifies whether the SSTED service is used or not. If the value of this object is 'selected' then I.366.1 SSSAR must be supported by the AAL2. This parameter only applies to those AAL2 channels using I.366.1 SSSAR.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	selected(1), notSelected(2)

atmfAAL2SscsSsadtStatus		1.3.6.1.4.1.353.2.12.6.1.8
This specifies whether SSADT service is used or not. Note that if the value of this object is 'selected' then I.366.1 SSSAR must be supported and by implication the SSTED service must also be 'selected'. This parameter only applies to those AAL2 channels using I.366.1 SSSAR.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	selected(1), notSelected(2)

atmfAAL2SscsServiceCategory		1.3.6.1.4.1.353.2.12.6.1.9
This object describes the type of service category supported by this AAL2 PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	audio(1), multirate(2), audioAndMultiRate(3)

atmfAAL2SscsAudioServiceTransport		1.3.6.1.4.1.353.2.12.6.1.10
This object describes whether the Audio Service that is used for transporting voice and voiceband data is enabled or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmfAAL2SscsProfileSource		1.3.6.1.4.1.353.2.12.6.1.11
This attribute describes the source of the profile.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	itut(1), other(2)

atmfAAL2SscsIeeeOui		1.3.6.1.4.1.353.2.12.6.1.12
This attribute contains the IEEE Organizationally Unique Identifier (OUI) of the organisation that specified the profile being used, if other than ITU-T. For example, if the source is the ATM Forum, the value of this object is 00A03E. This attribute is only meaningful if atmfAAL2SccsProfileSource has the value 'other'.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAAL2SscsPredefinedProfileIdentifier		1.3.6.1.4.1.353.2.12.6.1.13
This object describes the predefined profile identifier.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAAL2SscsPcmEncoding		1.3.6.1.4.1.353.2.12.6.1.14
This object describes the type of PCM encoding used.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	aLaw(1), ulaw(2)

atmfAAL2SscsFaxDemodulationTransport		1.3.6.1.4.1.353.2.12.6.1.15
This object describes whether transport of demodulated facsimile data is enabled or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmfAAL2SscsCasSignalingTransport		1.3.6.1.4.1.353.2.12.6.1.16
This attribute describes whether transport of CAS signaling bits is enabled or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmfAAL2SscsDtmfDigitPacketTransport		1.3.6.1.4.1.353.2.12.6.1.17
This attribute describes whether transport of DTMF dialled digits is enabled or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmfAAL2SscsMfR1DigitPacketTransport		1.3.6.1.4.1.353.2.12.6.1.18
This object describes whether transport of MF-R1 dialled digits is enabled or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmfAAL2SscsMfR2DigitPacketTransport		1.3.6.1.4.1.353.2.12.6.1.19
This object describes whether transport of MF-R2 dialled digits is enabled or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmfAAL2SscsCircuitModeDataTransport		1.3.6.1.4.1.353.2.12.6.1.20
This object describes whether transport of circuit mode data is enabled or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmfAAL2SscsCircuitModeDataNumChannels		1.3.6.1.4.1.353.2.12.6.1.21
This object describes the multiplier N in N*64kbit/s circuit mode data. It is only applicable if the value of atmfAAL2SscsCircuitModeDataTransport is 'enabled'.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..31

atmfAAL2SscsFrameModeDataTransport		1.3.6.1.4.1.353.2.12.6.1.22
This object describes whether the I.366.2 frame mode data service is enabled or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

atmfAAL2SscsFrameModeDataMaxLength		1.3.6.1.4.1.353.2.12.6.1.23
This object specifies the maximum length of I.366.2 frame mode data. It is only applicable if the value of atmfAAL2FrameModeDataTransport is 'enabled'.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

atmfAAL2SscopSduLength		1.3.6.1.4.1.353.2.12.6.1.24
The Maximum SSCOP-SDU length. This object is only required is the value of atmfAAL2SscsSsadtStatus is selected else it is not applicable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65524

atmfAAL2SscopUuFieldLength		1.3.6.1.4.1.353.2.12.6.1.25
The Maximum SSCOP-UU field length. This object is only required is the value of atmfAAL2SscsSsadtStatus is selected else it is not applicable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65524

atmfAAL2TrunkingProfileTable		1.3.6.1.4.1.353.2.12.7
The ATM Forum ILMI Auto Configuration Extension AAL2 Profile Information. This table contains AAL2 parameters that are specific to the ATM Trunking AAL 2 application. These parameters are taken from af-vtoa-0113.000
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAAL2TrunkingProfileEntry

atmfAAL2TrunkingProfileEntry		1.3.6.1.4.1.353.2.12.7.1
An atmfAAL2TrunkingProfileEntry provides AAL2 parameters of operation for ATM Trunking applications to be used in addition to those provided in the Common AAL2 Profile Table. These together provide complete configuration of AAL2 for PVCs that support ATM Trunking using AAl2 as defined in af-vtoa-0113.000.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAAL2TrunkingProfileEntry

atmfAAL2Vcci		1.3.6.1.4.1.353.2.12.7.1.1
This object uniquely identifies a PVC between IWFs.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAAL2SignalingVcci		1.3.6.1.4.1.353.2.12.7.1.2
This object specifies the VCCI of the PVC that is used to carry the CCS for this PVC.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAAL2LESProfileTable		1.3.6.1.4.1.353.2.12.8
The ATM Forum ILMI Auto Configuration Extension AAL2 Profile Information. This table contains AAL2 parameters that are specific to the ATM LES AAL 2 application. These parameters are taken from af-vmna-0145.000
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAAL2LESProfileEntry

atmfAAL2LESProfileEntry		1.3.6.1.4.1.353.2.12.8.1
An atmfAAL2LESProfileEntry provides AAL2 parameters of operation for LES applications to be used in addition to those provided in the Common AAL2 Profile Table. These together provide complete configuration of AAL2 for PVCs that support LES using AAl2 as defined in af-vmoa-0145.000.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAAL2LESProfileEntry

atmfAAL2CpsCIDLowerLimit		1.3.6.1.4.1.353.2.12.8.1.1
The minimum value the CID can take for AAL2 bearer channels and ISDN-D channels.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	16..223

atmfAAL2CpsCIDUpperLimit		1.3.6.1.4.1.353.2.12.8.1.2
The maximum value the CID can take for AAL2 bearer channels and ISDN-D channels.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	16..223

atmfAAL2CpsOptimisation		1.3.6.1.4.1.353.2.12.8.1.3
This object refers to the mode of operation of the CPS on the CP-IWF The value of this object imposes a restriction on the CPS-SDU length and hence must override the value of atmfAAl2CpsMaxSDULength. singleCpsPacketPerCpsPduNoOverlap -A single CPS Packet is contained within a CPS-PDU and no overlap can occur into the next CPS-PDU. If this option is selected, then Timer_CU is not applicable. Also Max CPS-SDU size must be less than or equal to 44. multipleCpsPacketsPerCpsPduWithOverlap - Multiple CPS Packets are contained within a CPS-PDU and overlap can occur into the next CPS-PDU. If this option is selected, then Timer_CU is applicable. Also Max CPS-SDU size must be less than or equal to 64.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	singleCpsPacketPerCpsPduNoOverlap(1), multipleCpsPacketsPerCpsPduWithOverlap(2)

atmfAtmServiceConnInfoExtensionTable		1.3.6.1.4.1.353.2.12.9
The ATM Forum ILMI Auto Configuration Extension ATM Service Connection Information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAtmServiceConnInfoExtensionEntry

atmfAtmServiceConnInfoExtensionEntry		1.3.6.1.4.1.353.2.12.9.1
An entry in the service connection information extension table provides additional elements that help describe the ATM connection that provides a service across an ATM interface. The connection is identified by port and VPI/VCI value.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAtmServiceConnInfoExtensionEntry

atmfAtmServicePhyMacIdentifier		1.3.6.1.4.1.353.2.12.9.1.1
When the physical and/or MAC layer has more than one PHY-connection or MAC-connection, this object is used to select the PHY- or MAC-connection to be bound to the PVC. The semantics of the value of this object is PHY and/or MAC specific. This semantics generally shall be specified with the PHY or MAC. However, the semantics for the two PHY/MAC specifications which have been identified as having multiple connections is provided here for convenience: When the physical layer is dual latency ADSL, the PhyMacIdentifier selects the latency path to be bound to each direction of transmission for the PVC. The value of the PhyMacIdentifier shall be as follows: default = 0 upstream and downstream both interleaved path = 1 upstream and downstream both fast path = 2 upstream interleaved path, downstream fast path = 3 upstream fast path, downstream interleaved path = 4 The 'default' value shall be used for single latency ADSL PHYs. When the physical and MAC layers are IEEE 802.14, the PhyMacIdentifier specifies the 802.14 Local Identifier for the PVC
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAtmServiceTypeExtensionTable		1.3.6.1.4.1.353.2.12.10
The ATM Forum ILMI Auto Configuration Extension ATM Service Type Extension Information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAtmServiceTypeExtensionEntry

atmfAtmServiceTypeExtensionEntry		1.3.6.1.4.1.353.2.12.10.1
An entry in the service type extension table describes additional information about a service that may be associated with individual ATM connections for the purpose of auto-configuration. This information describes the Client Protocol ID's associated with a particular service.
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAtmServiceTypeExtensionEntry

atmfAtmServiceLayer2ProtocolId		1.3.6.1.4.1.353.2.12.10.1.1
This object shall be used to select the user plane layer 2 protocol (if any) to be used above the AAL. The first octet of this object shall be encoded as follows. Bits 5-7 (i.e. the three most significant bits) shall be set to 0; any other values shall be ignored. Bits 0-4 (i.e. the five least significant bits) shall be encoded as shown in the entry for 'User information layer 2 protocol (octet 6)' in Table 4-10/Q.2931. However, if no user plane layer 2 protocol is present above the AAL, then the first (and only) octet shall be encoded as '0b00000000'. If the encoding of the first octet requires subsequent octets, then bit 7 (i.e., the most significant bit) of each of these octets shall be set to 0; however, if it is set to 1, it shall be ignored. Bits 0-6 shall be encoded according to table 4-10/Q.2931. If more than one subsequent octet is needed, then octets shall appear in the order shown in figure 4-16/Q.2931.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

atmfAtmServiceLayer3ProtocolId		1.3.6.1.4.1.353.2.12.10.1.2
This object shall be used to select a user plane layer 3 protocol (or user plane layer 2 bridging). The first octet of this object shall be encoded as follows. Bits 5-7 (i.e., the three most significant bits) shall be set to 0; any other values shall be ignored. Bits 0-4 (i.e., the five least significant bits) shall be encoded as shown in the entry for 'User information layer 3 protocol (octet 7)' in Table 4-10/Q.2931. However, if no user plane layer 3 protocol is specified, then the first (and only) octet shall be encoded as '0b00000000'. a) If ISO TR9577 network layer protocol identification is to be used, then the first octet shall be encoded to indicate 'ISO/IEC TR9577'. In this case, either: i) the user plane layer 3 protocol is to be selected in the management plane. The second octet of this object shall contain the ISO/IEC TR9577 Initial Protocol Identifier (IPI). - For layer 3 protocols for which ISO/IEC has assigned a Network Layer Protocol Identifier (NLPID), then this NLPID shall be used as the IPI, and the length of the octet string shall be 2. - For layer 3 protocols for which ISO/IEC has not assigned an NLPID, the IPI shall be encoded to indicate 'IEEE 802.1a SNAP identifier' (see Annex D of ISO/IEC 9577). The following five octets (octets 3 through 7) of this object shall then contain a SNAP identifier, which consists of a 3-octet organization unique identifier (OUI) and a 2-octet protocol identifier (PID). This SNAP coding shall be used only if ISO/IEC has not assigned a Network Layer Protocol Identifier for the layer 3 or layer 2 protocol. The octet string shall thus be 7 octets long. - If an IME wishes to indicate that bridged LAN frames are to be carried in the user plane then the IPI shall be encoded to indicate 'IEEE 802.1a SNAP identifier'. The following five octets of this object shall contain a SNAP identifier, which indicates the bridged protocol. For consistency with SIG 4.0, use of the ISO/IEC subsequent protocol identifier (SPI) is not recommended but not explicitly prohibited as one can envision scenarios where it has utility. or ii) the user plane layer 3 protocol is to be selected using network layer protocol identification in the user plane. The octet-string shall be one octet long. The first octet(s) of each layer 3 protocol data unit shall contain layer 3 protocol identification according to ISO/IEC TR9577. b)If bits 0-4 of the first octet of the octet string are set to any value other than 'ISO/IEC TR9577', then any subsequent octets shall be encoded as follows. Bit 7 (i.e., the most significant bit) of each of these octets shall be set to 0; however, if it is set to 1, it shall be ignored. Bits 0-6 shall be encoded according to the codings for octet 7a, octet 7b and octet 7c specified in table 4- 10/Q.2931. If more than one subsequent octet is needed, then octets shall appear in the order shown in figure 4-16/Q.2931.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

atmfAAL5ProfileExtensionTable		1.3.6.1.4.1.353.2.12.11
Additional parameters for the AAL5 Profile are stored in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AtmfAAL5ProfileExtensionEntry

atmfAAL5ProfileExtensionEntry		1.3.6.1.4.1.353.2.12.11.1
An entry in this table augments an entry in the atmfAAL5ProfileTable
Status: current	Access: not-accessible
OBJECT-TYPE
	AtmfAAL5ProfileExtensionEntry

atmfAAL5Vcci		1.3.6.1.4.1.353.2.12.11.1.1
This object's value is only applicable if the AAL5 VCC is carrying CCS for AAL2 narrowband calls.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

atmfAtmServiceConfFail		3
The user-side IME will send this trap whenever it is unable to configure itself based on the information provided in the ILMI auto-configuration MIB. The variables included in the trap identify the reason for the failure and the row in the MIB table that caused the failure.
TRAP-TYPE

atmfAtmServiceConfFailReason		1.3.6.1.4.1.353.2.12.12
The reason for the failure to configure the PVC at the ATU-R
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unsupportedClientProtocol(1), unsupportedServiceCategory(2), unsupportedAAL(3), invalidVPIVCIValue(4), tooManyPVCs(5), incompleteConfigurationInformation(6), inconsistentConfigurationInformation(7)

atmfAtmServiceConfFailOID		1.3.6.1.4.1.353.2.12.13
This object holds a pointer to a row in the appropriate table depending on the value of the atmfAtmServiceFailReason object. This will allow the network side to determine MIB information that caused the auto-configuration failure. The value of this object should be as follows: If atmfAtmServiceConfFailReason = 1 or 2, then this object's value points to the row in the atmfAtmServiceTypeTable that is the cause of the problem. If atmfAtmServiceConfFailReason = 3, then this object's value points to the row in the atmfAALxProfileTable, where x is 1, 2, 34, or 5 depending on the AAL that can't be supported. If atmfAtmServiceConfFailReason = 4, then this object's value points to the row in the atmfAtmServiceConnInfoTable that is the cause of the problem. For any other value of atmfAtmServiceConfFailReason, this object's value should be ignored.
Status: current	Access: read-only
OBJECT-TYPE
	RowPointer