ATM-DXI-MIB
File:
ATM-DXI-MIB.mib (7229 bytes)
Imported modules
Imported symbols
Defined Types
AtmDxiConfEntry |
|
SEQUENCE |
|
|
|
|
atmDxiConfIfIndex |
INTEGER |
|
|
atmDxiConfMode |
INTEGER |
|
AtmDxiDFAConfEntry |
|
SEQUENCE |
|
|
|
|
atmDxiDFAConfIfIndex |
INTEGER |
|
|
atmDxiDFAConfDfaIndex |
Dfa |
|
|
atmDxiDFAConfAALType |
INTEGER |
|
Defined Values
atmForum |
1.3.6.1.4.1.353 |
OBJECT IDENTIFIER |
|
|
|
atmUniDxi |
1.3.6.1.4.1.353.3 |
OBJECT IDENTIFIER |
|
|
|
atmDxi |
1.3.6.1.4.1.353.3.2 |
OBJECT IDENTIFIER |
|
|
|
atmDxiConfTable |
1.3.6.1.4.1.353.3.2.2 |
This table contains
ATM DXI configuration information
including information on the mode supported
across the DXI. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AtmDxiConfEntry |
|
atmDxiConfEntry |
1.3.6.1.4.1.353.3.2.2.1 |
This list contains ATM DXI configuration information. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AtmDxiConfEntry |
|
|
atmDxiConfIfIndex |
1.3.6.1.4.1.353.3.2.2.1.2 |
The value of this object identifies, for SNMP, the ATM DXI
interface for which this entry contains management information.
This is the same value as used to identify the IfEntry describing
the DCE interface. Management uses and expects this value. In
the proxy mode of operation, the DCE always treats this as 0, but
preserves it in its response to the DTE. 0, the DXI value, means
the interface over which the DXI LMI request was received. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
atmDxiConfMode |
1.3.6.1.4.1.353.3.2.2.1.3 |
This object identifies the dxi mode being
used at the atm dxi port. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
mode1a(1), mode1b(2), mode2(3) |
|
atmDxiDFAConfTable |
1.3.6.1.4.1.353.3.2.3 |
This table contains configuration information about
a particular DFA. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
AtmDxiDFAConfEntry |
|
atmDxiDFAConfEntry |
1.3.6.1.4.1.353.3.2.3.1 |
This list contains ATM DXI DFA configuration
information. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
AtmDxiDFAConfEntry |
|
|
atmDxiDFAConfIfIndex |
1.3.6.1.4.1.353.3.2.3.1.1 |
The value of this object identifies, for SNMP, the ATM DXI
interface for which this entry contains management information.
This is the same value as used to identify the IfEntry describing
the DCE interface. Management uses and expects this value. In
the proxy mode of operation, the DCE always treats this as 0, but
preserves it in its response to the DTE. 0, the DXI value, means
the interface over which the DXI LMI request was received. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
atmDxiDFAConfDfaIndex |
1.3.6.1.4.1.353.3.2.3.1.2 |
This object identifies the DFA instance on the DXI
identified by atmDxiDFAConfIfIndex. |
Status: mandatory |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Dfa |
|
|
atmDxiDFAConfAALType |
1.3.6.1.4.1.353.3.2.3.1.3 |
This object identifies the AAL type supported at this DFA.
Note, if mode 2 is supported on the DXI identified by the
corresponding instance of atmDxiDFAConfIfIndex and that
instance of atmDxiDFAConfIfIndex identifies the DCE side
of the DXI, then this object contains the AAL Type being
run on the corresponding VPI/VCI on the corresponding ATM UNI
interface. |
Status: mandatory |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
unknown(1), none(2), aal34(3), aal5(4) |
|
atmDxiEnterprise |
1.3.6.1.4.1.353.3.2.4 |
This object is included as the first ID-Value pair
in a Trap PDU for which the Generic Trap Type field
has the value 'enterpriseSpecific'. The value of the
object identifies the enterprise under whose authority
the value of the Enterprise Trap Type field is defined. |
Status: mandatory |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
OBJECT IDENTIFIER |
|
|