AT-GS950-24-MIB

File: AT-GS950-24-MIB.mib (518494 bytes)

Imported modules

SNMPv2-TC RFC1155-SMI SNMPv2-SMI
INET-ADDRESS-MIB IF-MIB LLDP-MIB
LLDP-EXT-DOT1-MIB LLDP-EXT-DOT3-MIB RFC1213-MIB
SNMPv2-CONF Q-BRIDGE-MIB SNMP-FRAMEWORK-MIB
SNMP-TARGET-MIB RMON2-MIB

Imported symbols

AutonomousType Counter Counter32
Counter64 DisplayString enterprises
InetAddress InetAddressPrefixLength InetAddressType
Integer32 InterfaceIndex InterfaceIndexOrZero
IpAddress lldpLocPortId lldpLocPortNum
lldpRemChassisId lldpRemManAddr lldpRemPortId
lldpRemSysName lldpStatsRemTablesAgeouts lldpStatsRemTablesDeletes
lldpStatsRemTablesDrops lldpStatsRemTablesInserts lldpXdot1RemPortVlanId
lldpXdot1RemProtocolId lldpXdot1RemProtoVlanSupported lldpXdot1RemVlanName
lldpXdot3RemLinkAggStatus lldpXdot3RemMaxFrameSize lldpXdot3RemPortOperMauType
lldpXdot3RemPowerClass MacAddress mib-2
MODULE-COMPLIANCE MODULE-IDENTITY NOTIFICATION-TYPE
OBJECT-GROUP OBJECT-TYPE PhysAddress
PortList RowStatus SnmpAdminString
SnmpEngineID SnmpSecurityLevel SnmpSecurityModel
SnmpTagValue snmpTargetParamsName TAddress
TEXTUAL-CONVENTION TimeFilter TimeInterval
TimeStamp TimeTicks TruthValue
Unsigned32 ZeroBasedCounter32

Defined Types

L2snmpLevel  
Tok_String
TEXTUAL-CONVENTION    
  INTEGER v1(1), v2c(2), noAuthNoPriv(3), authNoPriv(4), authPriv(5)  

TabSnmpUserEntry  
SEQUENCE    
  sysSnmpUserName SnmpAdminString
  sysSnmpUserAuthProtocol AutonomousType
  sysSnmpUserPrivProtocol AutonomousType
  sysSnmpUserStatus RowStatus

TabSnmpGroupEntry  
SEQUENCE    
  sysSnmpSecurityModel SnmpSecurityModel
  sysSnmpSecurityName SnmpAdminString
  sysSnmpGroupName SnmpAdminString
  sysSnmpGroupStatus RowStatus

TabSnmpGroupAccessEntry  
SEQUENCE    
  sysSnmpaccessGroupIndex SnmpAdminString
  sysSnmpaccessSecurityModel SnmpSecurityModel
  sysSnmpaccessSecurityLevel SnmpSecurityLevel
  sysSnmpaccessReadViewName SnmpAdminString
  sysSnmpaccessWriteViewName SnmpAdminString
  sysSnmpaccessNotifyViewName SnmpAdminString
  sysSnmpaccessStatus RowStatus

TabSnmpViewTreeEntry  
SEQUENCE    
  sysSnmpviewTreeName SnmpAdminString
  sysSnmpviewTreeSubtree OBJECT IDENTIFIER
  sysSnmpviewTreeMask OCTET STRING
  sysSnmpviewTreeType INTEGER
  sysSnmpviewTreeStatus RowStatus

TabSnmpCommunityEntry  
SEQUENCE    
  sysSnmpsnmpCommunityIndex SnmpAdminString
  sysSnmpsnmpCommunityName SnmpAdminString
  sysSnmpsnmpCommunityPolicy SnmpAdminString
  sysSnmpsnmpCommunityStatus RowStatus

TabSnmpTrapManagerEntry  
SEQUENCE    
  sysSnmpsnmpTrapManagerName SnmpAdminString
  sysSnmpsnmpTrapManagerAddress TAddress
  sysSnmpsnmpTrapManagerSecurityLevel L2snmpLevel
  sysSnmpsnmpTrapManagerStatus RowStatus

TabRadiusExtServerEntry  
SEQUENCE    
  sysRadiusExtServerIndex InterfaceIndex
  sysRadiusExtServerAddress IpAddress
  sysRadiusExtServerSharedSecret DisplayString
  sysRadiusExtServerResponseTime INTEGER
  sysRadiusExtServerMaximumRetransmission INTEGER
  sysRadiusExtServerAuthPortNum INTEGER
  sysRadiusExtServerEntryStatus RowStatus
  sysRadiusExtServerAccPort INTEGER

TabIfMainEntry  
SEQUENCE    
  ifMainIndex InterfaceIndex
  ifMainType INTEGER
  ifMainMtu Integer32
  ifMainAdminStatus INTEGER
  ifMainOperStatus INTEGER
  ifMainEncapType INTEGER
  ifMainBrgPortType INTEGER
  ifMainRowStatus RowStatus

TabIfIpEntry  
SEQUENCE    
  ifIpAddrAllocMethod INTEGER
  ifIpAddr IpAddress
  ifIpSubnetMask IpAddress
  ifIpBroadcastAddr IpAddress
  ifIpForwardingEnable TruthValue
  ifIpAddrAllocProtocol INTEGER

TabIfIvrEntry  
SEQUENCE    
  ifIvrBridgedIface TruthValue

TabIfSecondaryIpAddressEntry  
SEQUENCE    
  ifSecondaryIpAddress IpAddress
  ifSecondaryIpSubnetMask IpAddress
  ifSecondaryIpBroadcastAddr IpAddress
  ifSecondaryIpRowStatus RowStatus

PortLaMode  
Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. manual(2) - force the port to enable channeling. disable(3) - channeling is disabled.
TEXTUAL-CONVENTION    
  INTEGER lacp(1), manual(2), disable(3)  

LacpKey  
The Actor or Partner Key value.
TEXTUAL-CONVENTION    
  Integer32 0..65535  

LacpState  
The Actor and Partner State values from the LACPDU.
TEXTUAL-CONVENTION    
  BITS lacpActivity(0), lacpTimeout(1), aggregation(2), synchronization(3), collecting(4), distributing(5), defaulted(6), expired(7)  

TabLaPortChannelEntry  
SEQUENCE    
  sysLaPortChannelIfIndex InterfaceIndex
  sysLaPortChannelGroup LacpKey
  sysLaPortChannelAdminMacAddress MacAddress
  sysLaPortChannelMacSelection INTEGER
  sysLaPortChannelMode PortLaMode
  sysLaPortChannelPortCount Integer32
  sysLaPortChannelActivePortCount Integer32
  sysLaPortChannelSelectionPolicy INTEGER
  sysLaPortChannelDefaultPortIndex InterfaceIndexOrZero

TabLaPortEntry  
SEQUENCE    
  sysLaPortIndex InterfaceIndex
  sysLaPortMode PortLaMode
  sysLaPortBundleState INTEGER
  sysLaPortActorResetAdminState LacpState
  sysLaPortAggregateWaitTime TimeTicks
  sysLaPortPartnerResetAdminState LacpState
  sysLaPortActorAdminPort Integer32
  sysLaPortRestoreMtu Integer32
  sysLaPortSelectAggregator INTEGER

PaeControlledPortStatus  
The status values of the Authenticator PAE controlled session.
TEXTUAL-CONVENTION    
  INTEGER authorized(1), unauthorized(2)  

AuthenticMethod  
The Authentication method is using Remote Authentication Server or Local Authentication Server.
TEXTUAL-CONVENTION    
  INTEGER remoteServer(1), localServer(2)  

PermissionType  
The permission values.
TEXTUAL-CONVENTION    
  INTEGER allow(1), deny(2)  

TabPnacPaePortEntry  
SEQUENCE    
  sysPnacPaePortNumber InterfaceIndex
  sysPnacPaePortStatus PaeControlledPortStatus
  sysPnacPaeMultiAuthEnable INTEGER
  sysPnacPaeProtocolMode Integer32
  sysPnacPaePiggybackMode INTEGER
  sysPnacPaeVlanAssignment INTEGER
  sysPnacPaeSecureVlan INTEGER

TabPnacASUserConfigEntry  
SEQUENCE    
  sysPnacASUserConfigUserName OCTET STRING
  sysPnacASUserConfigPassword DisplayString
  sysPnacASUserConfigAuthProtocol Unsigned32
  sysPnacASUserConfigAuthTimeout Unsigned32
  sysPnacASUserConfigPortList PortList
  sysPnacASUserConfigPermission PermissionType
  sysPnacASUserConfigDynamicVlanID Unsigned32
  sysPnacASUserConfigRowStatus RowStatus

TabPnacGuestVlanEntry  
SEQUENCE    
  sysPnacPaePortNo Integer32
  sysPnacGuestVlanId Integer32

TabConfigCtrlEntry  
SEQUENCE    
  sysConfigCtrlIndex Integer32
  sysConfigCtrlEgressStatus INTEGER
  sysConfigCtrlStatsCollection INTEGER
  sysConfigCtrlStatus INTEGER

TabPortCtrlEntry  
SEQUENCE    
  sysPortCtrlIndex Integer32
  sysPortCtrlMode INTEGER
  sysPortCtrlDuplex INTEGER
  sysPortCtrlSpeed INTEGER
  sysPortCtrlFlowControl INTEGER
  sysPortCtrlMDI INTEGER
  issJumboFramePerPortEnable INTEGER
  issJumboFramePerPortMtu Integer32
  sysPortCtrlEAPPassThrough INTEGER
  sysPortCtrlBPDUPassThrough INTEGER

TabMirrorCtrlEntry  
SEQUENCE    
  sysMirrorCtrlIndex Integer32
  sysMirrorCtrlIngressMirroring INTEGER
  sysMirrorCtrlEgressMirroring INTEGER
  sysMirrorCtrlStatus INTEGER

TabIpAuthMgrEntry  
SEQUENCE    
  sysIpAuthMgrIpAddr IpAddress
  sysIpAuthMgrIpMask IpAddress
  sysIpAuthMgrPortList PortList
  sysIpAuthMgrVlanList OCTET STRING
  sysIpAuthMgrAllowedServices Integer32
  sysIpAuthMgrRowStatus RowStatus

SysLBDCtrlEntry  
SEQUENCE    
  sysLBDCtrlIndex Integer32
  sysLBDPortStatus INTEGER
  sysLBDPortLoopStatus INTEGER

TabRateCtrlEntry  
SEQUENCE    
  sysRateCtrlIndex Integer32
  sysRateCtrlEgressLimitValue Integer32
  sysRateCtrlIngressLimitValue Integer32

TabStormCtrlEntry  
SEQUENCE    
  sysStormCtrlIndex Integer32
  sysDlfOnOff INTEGER
  sysBroadcastOnOff INTEGER
  sysMulticastOnOff INTEGER
  sysStormCtrlThreshold INTEGER
  sysStormCtrlRowStatus RowStatus

TabUserAuthMgrEntry  
SEQUENCE    
  sysUserAuthMgrId Integer32
  sysUserAuthMgrName OCTET STRING
  sysUserAuthMgrRowStatus RowStatus

IfDirection  
IfDirection specifies a direction of data travel on an interface. 'inbound' traffic is operated on during recsystion from the interface, while 'outbound' traffic is operated on prior to transmission on the interface.
TEXTUAL-CONVENTION    
  INTEGER outbound(1), inbound(2)  

DscpOrAny  
The IP header Differentiated Services Code-Point that may be used for discriminating among traffic streams. The value -1 is used to indicate a wild card i.e. any value.
TEXTUAL-CONVENTION    
  Unsigned32 0..63  

TabDscpMultiFieldClfrEntry  
SEQUENCE    
  sysDfsMultiFieldClfrId Integer32
  sysDfsMultiFieldClfrFilterId Unsigned32
  sysDfsMultiFieldClfrFilterType INTEGER
  sysDfsMultiFieldClfrStatus RowStatus

TabDscpClfrEntry  
SEQUENCE    
  sysDfsClfrId Integer32
  sysDfsClfrMFClfrId Integer32
  sysDfsClfrInProActionId Integer32
  sysDfsClfrOutProActionId Integer32
  sysDfsClfrStatus RowStatus

TabDscpInProfileActionEntry  
SEQUENCE    
  sysDfsInProfileActionId Integer32
  sysDfsInProfileActionFlag Unsigned32
  sysDfsInProfileActionNewPrio Unsigned32
  sysDfsInProfileActionDscp DscpOrAny
  sysDfsInProfileActionStatus RowStatus

TabDscpOutProfileActionEntry  
SEQUENCE    
  sysDfsOutProfileActionId Integer32
  sysDfsOutProfileActionFlag Unsigned32
  sysDfsOutProfileActionMID Integer32
  sysDfsOutProfileActionStatus RowStatus

TabDscpMeterEntry  
SEQUENCE    
  sysDfsMeterId Integer32
  sysDfsMeterRefreshCount Unsigned32
  sysDfsMeterStatus RowStatus

TabDscpCoSqAlgorithmEntry  
SEQUENCE    
  sysDfsPortId Integer32
  sysDfsCoSqAlgorithm INTEGER

InetAddressIPv4  
Represents an IPv4 network address: octets contents encoding 1-4 IP address network-byte order The corresponding InetAddressType value is ipv4(1).
TEXTUAL-CONVENTION    
  OCTET STRING Size(4)  

InetAddressIPv6  
Represents an IPv6 network address: octets contents encoding 1-16 IPv6 address network-byte order 17-20 scope identifier network-byte order The corresponding InetAddressType value is ipv6(2). The scope identifier (bytes 17-20) MUST NOT be present for global IPv6 addresses. For non-global IPv6 addresses (e.g. link-local or site-local addresses), the scope identifier MUST always be present. It contains a link identifier for link-local and a site identifier for site-local IPv6 addresses. The scope identifier MUST disambiguate identical address values. For link-local addresses, the scope identifier will typically be the interface index (ifIndex as defined in the IF-MIB, RFC 2233) of the interface on which the address is configured. The scope identifier may contain the special value 0 which refers to the default scope. The default scope may be used in cases where the valid scope identifier is not known (e.g., a management application needs to write a site-local InetAddressIPv6 address without knowing the site identifier value). The default scope SHOULD NOT be used as an easy way out in cases where the scope identifier for a non-global IPv6 is known.
TEXTUAL-CONVENTION    
  OCTET STRING Size(16|20)  

InetAddressDNS  
Represents a DNS domain name. The name SHOULD be fully qualified whenever possible. The corresponding InetAddressType is dns(16). The DESCRIPTION clause of InetAddress objects that may have InetAddressDNS values must fully describe how (and when) such names are to be resolved to IP addresses.
TEXTUAL-CONVENTION    
  OCTET STRING Size(1..255)  

TabSyslogConfigEntry  
SEQUENCE    
  sysSyslogConfigModule Integer32
  sysSyslogConfigLogLevel INTEGER

TabPortSecEntry  
SEQUENCE    
  sysPortSecurityIndex Integer32
  sysPortSecurityState INTEGER
  sysPortSecurityMLA Integer32

TabSnoopInstanceGlobalEntry  
SEQUENCE    
  sysSnoopInstanceGlobalInstId Integer32
  sysSnoopInstanceGlobalSystemControl INTEGER

TabSnoopInstanceConfigEntry  
SEQUENCE    
  sysSnoopInstanceConfigInstId Integer32
  sysSnoopInetAddressType InetAddressType
  sysSnoopStatus INTEGER
  sysSnoopRouterPortPurgeInterval Integer32
  sysSnoopPortPurgeInterval Integer32
  sysSnoopReportForwardInterval Integer32
  sysSnoopRetryCount Integer32
  sysSnoopGrpQueryInterval Integer32
  sysSnoopReportFwdOnAllPorts INTEGER
  sysSnoopOperStatus INTEGER
  sysSnoopSendQueryOnTopoChange INTEGER
  sysSnoopQuerierQueryInterval Integer32

TabSnoopVlanMcastMacFwdEntry  
SEQUENCE    
  sysSnoopVlanMcastMacFwdInstId Integer32
  sysSnoopVlanMcastMacFwdVlanId Integer32
  sysSnoopVlanMcastMacFwdInetAddressType InetAddressType
  sysSnoopVlanMcastMacFwdGroupAddress MacAddress
  sysSnoopVlanMcastMacFwdPortList PortList

TabSnoopVlanRouterEntry  
SEQUENCE    
  sysSnoopVlanRouterInstId Integer32
  sysSnoopVlanRouterVlanId Integer32
  sysSnoopVlanRouterInetAddressType InetAddressType
  sysSnoopVlanRouterPortList PortList

TabSnoopVlanFilterEntry  
SEQUENCE    
  sysSnoopVlanFilterInstId Integer32
  sysSnoopVlanFilterVlanId Integer32
  sysSnoopVlanFilterInetAddressType InetAddressType
  sysSnoopVlanSnoopStatus INTEGER
  sysSnoopVlanOperatingVersion INTEGER
  sysSnoopVlanFastLeave INTEGER
  sysSnoopVlanQuerier INTEGER
  sysSnoopVlanCfgQuerier INTEGER
  sysSnoopVlanQueryInterval Integer32
  sysSnoopVlanRtrPortList PortList
  sysSnoopVlanRowStatus RowStatus

TabSnoopStatsEntry  
SEQUENCE    
  sysSnoopStatsInstId Integer32
  sysSnoopStatsVlanId Integer32
  sysSnoopStatsInetAddressType InetAddressType
  sysSnoopStatsRxGenQueries Counter32
  sysSnoopStatsRxGrpQueries Counter32
  sysSnoopStatsRxAsmReports Counter32
  sysSnoopStatsRxAsmLeaves Counter32
  sysSnoopStatsTxGenQueries Counter32
  sysSnoopStatsTxGrpQueries Counter32
  sysSnoopStatsTxAsmReports Counter32
  sysSnoopStatsTxAsmLeaves Counter32
  sysSnoopStatsDroppedPkts Counter32

BridgeId  
The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to refer to a bridge in a unique fashion (typically, the numerically smallest MAC address of all ports on the bridge). Several objects in this MIB module represent values of timers used by the Spanning Tree Protocol. In this MIB, these timers have values in units of hundreths of a second (i.e. 1/100 secs). These timers, when stored in a Spanning Tree Protocol's BPDU, are in units of 1/256 seconds. Note, however, that 802.1D-1990 specifies a settable granularity of no more than 1 second for these timers. To avoid ambiguity, a data type is defined here as a textual convention and all representation of these timers in this MIB module are defined using this data type. An algorithm is also defined for converting between the different units, to ensure a timer's value is not distorted by multiple conversions.
TEXTUAL-CONVENTION    
  OCTET STRING Size(8)  

Timeout  
A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: floor = quotient [ignore remainder] n is the value in 1/100 second units b is the value in 1/256 second units To convert the value from 1/256 second units back to 1/100 seconds, the following algorithm should be used: n = ceiling( (b * 100) / 256) where: ceiling = quotient [if remainder is 0], or quotient + 1 [if remainder is non-zero] n is the value in 1/100 second units b is the value in 1/256 second units Note: it is important that the arithmetic operations are done in the order specified (i.e., multiply first, divide second).
TEXTUAL-CONVENTION    
  INTEGER  

TabDot1dBaseEntry  
SEQUENCE    
  dot1dBaseContextId Integer32
  dot1dBaseBridgeAddress MacAddress
  dot1dBaseNumPorts Integer32
  dot1dBaseType INTEGER

TabDot1dBasePortEntry  
SEQUENCE    
  dot1dBasePort Integer32
  dot1dBasePortIfIndex Integer32
  dot1dBasePortCircuit OBJECT IDENTIFIER
  dot1dBasePortDelayExceededDiscards Counter32
  dot1dBasePortMtuExceededDiscards Counter32

TabDot1dStpEntry  
SEQUENCE    
  dot1dStpContextId Integer32
  dot1dStpProtocolSpecification INTEGER
  dot1dStpPriority Integer32
  dot1dStpTimeSinceTopologyChange TimeTicks
  dot1dStpTopChanges Counter32
  dot1dStpDesignatedRoot BridgeId
  dot1dStpRootCost Integer32
  dot1dStpRootPort Integer32
  dot1dStpMaxAge Timeout
  dot1dStpHelloTime Timeout
  dot1dStpHoldTime Integer32
  dot1dStpForwardDelay Timeout
  dot1dStpBridgeMaxAge Timeout
  dot1dStpBridgeHelloTime Timeout
  dot1dStpBridgeForwardDelay Timeout

TabDot1dStpPortEntry  
SEQUENCE    
  dot1dStpPort Integer32
  dot1dStpPortPriority Integer32
  dot1dStpPortState INTEGER
  dot1dStpPortEnable INTEGER
  dot1dStpPortPathCost Integer32
  dot1dStpPortDesignatedRoot BridgeId
  dot1dStpPortDesignatedCost INTEGER
  dot1dStpPortDesignatedBridge BridgeId
  dot1dStpPortDesignatedPort OCTET STRING
  dot1dStpPortForwardTransitions Counter32

TabDot1dTpEntry  
SEQUENCE    
  dot1dTpLearnedEntryDiscards Counter32
  dot1dTpAgingTime INTEGER

TabDot1dTpFdbEntry  
SEQUENCE    
  dot1dTpFdbAddress MacAddress
  dot1dTpFdbPort Integer32
  dot1dTpFdbStatus INTEGER

TabDot1dTpPortEntry  
SEQUENCE    
  dot1dTpPort Integer32
  dot1dTpPortMaxInfo Integer32
  dot1dTpPortInFrames Counter32
  dot1dTpPortOutFrames Counter32
  dot1dTpPortInDiscards Counter32

TabDot1dStaticEntry  
SEQUENCE    
  dot1dStaticAddress MacAddress
  dot1dStaticReceivePort INTEGER
  dot1dStaticRowStatus RowStatus
  dot1dStaticStatus INTEGER

TabDot1dStaticAllowedToGoEntry  
SEQUENCE    
  dot1dStaticAllowedIsMember TruthValue

TabDot1dStpExtEntry  
SEQUENCE    
  dot1dStpVersion INTEGER
  dot1dStpTxHoldCount Integer32
  dot1dStpPathCostDefault INTEGER

TabDot1dStpExtPortEntry  
SEQUENCE    
  dot1dStpPortProtocolMigration TruthValue
  dot1dStpPortAdminEdgePort TruthValue
  dot1dStpPortOperEdgePort TruthValue
  dot1dStpPortAdminPointToPoint INTEGER
  dot1dStpPortOperPointToPoint TruthValue

EnabledStatus  
A simple status value for the object.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

TabDot1dExtBaseEntry  
SEQUENCE    
  dot1dBridgeContextId Integer32
  dot1dDeviceCapabilities BITS
  dot1dTrafficClassesEnabled TruthValue
  dot1dGmrpStatus EnabledStatus

TabDot1dPortCapabilitiesEntry  
SEQUENCE    
  dot1dPortCapabilities BITS

TabDot1dPortPriorityEntry  
SEQUENCE    
  dot1dPortDefaultUserPriority Integer32
  dot1dPortNumTrafficClasses Integer32

Dot1dUserPriorityRegenEntry  
SEQUENCE    
  dot1dUserPriority Integer32
  dot1dRegenUserPriority Integer32

TabDot1dTrafficClassEntry  
SEQUENCE    
  dot1dTrafficClassPriority Integer32
  dot1dTrafficClass Integer32

Dot1dPortOutboundAccessPriorityEntry  
SEQUENCE    
  dot1dPortOutboundAccessPriority Integer32

TabDot1dPortGarpEntry  
SEQUENCE    
  dot1dPortGarpJoinTime TimeInterval
  dot1dPortGarpLeaveTime TimeInterval
  dot1dPortGarpLeaveAllTime TimeInterval

TabDot1dTpHCPortEntry  
SEQUENCE    
  dot1dTpHCPortInFrames Counter64
  dot1dTpHCPortOutFrames Counter64
  dot1dTpHCPortInDiscards Counter64

TabDot1dTpPortOverflowEntry  
SEQUENCE    
  dot1dTpPortInOverflowFrames Counter32
  dot1dTpPortOutOverflowFrames Counter32
  dot1dTpPortInOverflowDiscards Counter32

VlanIndex  
A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095 then it represents a VLAN with scope local to the particular agent, i.e. one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q but it is convenient to be able to manage them in the same way using this MIB.
TEXTUAL-CONVENTION    
  Unsigned32  

VlanId  
A 12-bit VLAN ID used in the VLAN Tag header.
TEXTUAL-CONVENTION    
  Integer32 1..4094  

TabDot1qBaseEntry  
SEQUENCE    
  dot1qVlanContextId Integer32
  dot1qVlanVersionNumber INTEGER
  dot1qMaxVlanId VlanId
  dot1qMaxSupportedVlans Unsigned32
  dot1qNumVlans Unsigned32
  dot1qGvrpStatus INTEGER

TabDot1qFdbEntry  
SEQUENCE    
  dot1qFdbId Unsigned32
  dot1qFdbDynamicCount Counter32

TabDot1qTpFdbEntry  
SEQUENCE    
  dot1qTpFdbAddress MacAddress
  dot1qTpFdbPort Integer32
  dot1qTpFdbStatus INTEGER
  dot1qTpFdbPw Unsigned32

TabDot1qStaticUnicastEntry  
SEQUENCE    
  dot1qStaticUnicastAddress MacAddress
  dot1qStaticUnicastReceivePort Integer32
  dot1qStaticUnicastRowStatus RowStatus
  dot1qStaticUnicastStatus INTEGER

TabDot1qStaticAllowedToGoEntry  
SEQUENCE    
  dot1qStaticAllowedIsMember TruthValue
  dot1qTpPort Integer32

TabDot1qStaticMulticastEntry  
SEQUENCE    
  dot1qStaticMulticastAddress MacAddress
  dot1qStaticMulticastReceivePort Integer32
  dot1qStaticMulticastRowStatus RowStatus
  dot1qStaticMulticastStatus INTEGER

TabDot1qStaticMcastPortEntry  
SEQUENCE    
  dot1qStaticMcastPort INTEGER
  dot1qVlanIndex VlanIndex

TabDot1qVlanNumDeletesEntry  
SEQUENCE    
  dot1qVlanNumDeletes Counter32

TabDot1qVlanCurrentEntry  
SEQUENCE    
  dot1qVlanTimeMark TimeFilter
  dot1qVlanFdbId Unsigned32
  dot1qVlanStatus INTEGER
  dot1qVlanCreationTime TimeTicks

TabDot1qVlanEgressPortEntry  
SEQUENCE    
  dot1qVlanCurrentEgressPort INTEGER

TabDot1qVlanStaticEntry  
SEQUENCE    
  dot1qVlanStaticName SnmpAdminString
  dot1qVlanStaticRowStatus RowStatus

TabDot1qVlanStaticPortConfigEntry  
SEQUENCE    
  dot1qVlanStaticPort INTEGER

TabDot1qPortVlanEntry  
SEQUENCE    
  dot1qPvid VlanIndex
  dot1qPortAcceptableFrameTypes INTEGER
  dot1qPortIngressFiltering TruthValue
  dot1qPortGvrpStatus EnabledStatus
  dot1qPortGvrpFailedRegistrations Counter32
  dot1qPortGvrpLastPduOrigin MacAddress
  dot1qPortRestrictedVlanRegistration TruthValue

TabDot1sMstEntry  
SEQUENCE    
  dot1sMstContextId Integer32
  dot1sSystemControl INTEGER
  dot1sModuleStatus EnabledStatus
  dot1sMaxMstInstanceNumber Integer32
  dot1sNoOfMstiSupported Integer32
  dot1sMaxHopCount Integer32
  dot1sBrgAddress MacAddress
  dot1sCistRoot BridgeId
  dot1sCistRegionalRoot BridgeId
  dot1sCistRootCost Integer32
  dot1sCistRegionalRootCost Integer32
  dot1sCistRootPort Integer32
  dot1sCistBridgePriority Integer32
  dot1sCistBridgeMaxAge Timeout
  dot1sCistBridgeForwardDelay Timeout
  dot1sCistHoldTime Integer32
  dot1sCistMaxAge Timeout
  dot1sCistForwardDelay Timeout
  dot1sMstpUpCount Counter32
  dot1sMstpDownCount Counter32
  dot1sPathCostDefaultType INTEGER
  dot1sTrace Integer32
  dot1sDebug Integer32
  dot1sForceProtocolVersion INTEGER
  dot1sTxHoldCount Integer32
  dot1sMstiConfigIdSel Integer32
  dot1sMstiRegionName OCTET STRING
  dot1sMstiRegionVersion Integer32
  dot1sMstiConfigDigest OCTET STRING
  dot1sBufferOverFlowCount Counter32
  dot1sMemAllocFailureCount Counter32
  dot1sRegionConfigChangeCount Counter32
  dot1sCistBridgeRoleSelectionSemState INTEGER
  dot1sCistTimeSinceTopologyChange TimeTicks
  dot1sCistTopChanges Counter32
  dot1sCistNewRootBridgeCount Counter32
  dot1sCistHelloTime Timeout
  dot1sCistBridgeHelloTime Timeout
  dot1sCistDynamicPathcostCalculation TruthValue
  dot1sContextName DisplayString

TabDot1sMstiBridgeEntry  
SEQUENCE    
  dot1sMstiInstanceIndex Integer32
  dot1sMstiBridgeRegionalRoot BridgeId
  dot1sMstiBridgePriority Integer32
  dot1sMstiRootCost Integer32
  dot1sMstiRootPort Integer32
  dot1sMstiTimeSinceTopologyChange TimeTicks
  dot1sMstiTopChanges Counter32
  dot1sMstiNewRootBridgeCount Counter32
  dot1sMstiBridgeRoleSelectionSemState INTEGER
  dot1sInstanceUpCount Counter32
  dot1sInstanceDownCount Counter32
  dot1sOldDesignatedRoot BridgeId

TabDot1sVlanInstanceMappingEntry  
SEQUENCE    
  dot1sInstanceIndex Integer32
  dot1sMapVlanIndex VlanId
  dot1sUnMapVlanIndex VlanId
  dot1sSetVlanList OCTET STRING
  dot1sResetVlanList OCTET STRING
  dot1sInstanceVlanMapped OCTET STRING
  dot1sInstanceVlanMapped2k OCTET STRING
  dot1sInstanceVlanMapped3k OCTET STRING
  dot1sInstanceVlanMapped4k OCTET STRING

TabDot1sCistPortEntry  
SEQUENCE    
  dot1sCistPort Integer32
  dot1sCistPortPathCost Integer32
  dot1sCistPortPriority Integer32
  dot1sCistPortDesignatedRoot BridgeId
  dot1sCistPortDesignatedBridge BridgeId
  dot1sCistPortDesignatedPort OCTET STRING
  dot1sCistPortAdminP2P INTEGER
  dot1sCistPortOperP2P TruthValue
  dot1sCistPortAdminEdgeStatus TruthValue
  dot1sCistPortOperEdgeStatus TruthValue
  dot1sCistPortProtocolMigration TruthValue
  dot1sCistPortState INTEGER
  dot1sCistForcePortState INTEGER
  dot1sCistPortForwardTransitions Counter32
  dot1sCistPortRxMstBpduCount Counter32
  dot1sCistPortRxRstBpduCount Counter32
  dot1sCistPortRxConfigBpduCount Counter32
  dot1sCistPortRxTcnBpduCount Counter32
  dot1sCistPortTxMstBpduCount Counter32
  dot1sCistPortTxRstBpduCount Counter32
  dot1sCistPortTxConfigBpduCount Counter32
  dot1sCistPortTxTcnBpduCount Counter32
  dot1sCistPortInvalidMstBpduRxCount Counter32
  dot1sCistPortInvalidRstBpduRxCount Counter32
  dot1sCistPortInvalidConfigBpduRxCount Counter32
  dot1sCistPortInvalidTcnBpduRxCount Counter32
  dot1sCistPortTransmitSemState INTEGER
  dot1sCistPortReceiveSemState INTEGER
  dot1sCistPortProtMigrationSemState INTEGER
  dot1sCistProtocolMigrationCount Counter32
  dot1sCistPortDesignatedCost Integer32
  dot1sCistPortRegionalRoot BridgeId
  dot1sCistPortRegionalPathCost Integer32
  dot1sCistSelectedPortRole INTEGER
  dot1sCistCurrentPortRole INTEGER
  dot1sCistPortInfoSemState INTEGER
  dot1sCistPortRoleTransitionSemState INTEGER
  dot1sCistPortStateTransitionSemState INTEGER
  dot1sCistPortTopologyChangeSemState INTEGER
  dot1sCistPortHelloTime Timeout
  dot1sCistPortOperVersion INTEGER
  dot1sCistPortEffectivePortState TruthValue
  dot1sCistPortAutoEdgeStatus TruthValue
  dot1sCistPortRestrictedRole TruthValue
  dot1sCistPortRestrictedTCN TruthValue

TabDot1sMstiPortEntry  
SEQUENCE    
  dot1sMstiPort Integer32
  dot1sMstiPortPathCost Integer32
  dot1sMstiPortPriority Integer32
  dot1sMstiPortDesignatedRoot BridgeId
  dot1sMstiPortDesignatedBridge BridgeId
  dot1sMstiPortDesignatedPort OCTET STRING
  dot1sMstiPortState INTEGER
  dot1sMstiForcePortState INTEGER
  dot1sMstiPortForwardTransitions Counter32
  dot1sMstiPortReceivedBPDUs Counter32
  dot1sMstiPortTransmittedBPDUs Counter32
  dot1sMstiPortInvalidBPDUsRcvd Counter32
  dot1sMstiPortDesignatedCost Integer32
  dot1sMstiSelectedPortRole INTEGER
  dot1sMstiCurrentPortRole INTEGER
  dot1sMstiPortInfoSemState INTEGER
  dot1sMstiPortRoleTransitionSemState INTEGER
  dot1sMstiPortStateTransitionSemState INTEGER
  dot1sMstiPortTopologyChangeSemState INTEGER
  dot1sMstiPortEffectivePortState TruthValue

TabDot1sMstTrapsControlEntry  
SEQUENCE    
  dot1sSetTraps Integer32
  dot1sGenTrapType INTEGER

TabDot1sPortTrapNotificationEntry  
SEQUENCE    
  dot1sPortTrapIndex Integer32
  dot1sPortMigrationType INTEGER
  dot1sPktErrType INTEGER
  dot1sPktErrVal Integer32

TabDot1sPortRoleTrapNotificationEntry  
SEQUENCE    
  dot1sPortRoleType INTEGER
  dot1sOldRoleType INTEGER

TabDot1wRstEntry  
SEQUENCE    
  dot1wRstContextId Integer32
  dot1wSystemControl INTEGER
  dot1wModuleStatus EnabledStatus
  dot1wTraceOption Integer32
  dot1wDebugOption Integer32
  dot1wRstpUpCount Counter32
  dot1wRstpDownCount Counter32
  dot1wBufferFailureCount Counter32
  dot1wMemAllocFailureCount Counter32
  dot1wNewRootIdCount Counter32
  dot1wPortRoleSelSmState INTEGER
  dot1wOldDesignatedRoot BridgeId
  dot1wDynamicPathcostCalculation TruthValue
  dot1wContextName DisplayString

TabDot1wPortExtEntry  
SEQUENCE    
  dot1wPort Integer32
  dot1wPortRole INTEGER
  dot1wPortOperVersion INTEGER
  dot1wPortInfoSmState INTEGER
  dot1wPortMigSmState INTEGER
  dot1wPortRoleTransSmState INTEGER
  dot1wPortStateTransSmState INTEGER
  dot1wPortTopoChSmState INTEGER
  dot1wPortTxSmState INTEGER
  dot1wPortRxRstBpduCount Counter32
  dot1wPortRxConfigBpduCount Counter32
  dot1wPortRxTcnBpduCount Counter32
  dot1wPortTxRstBpduCount Counter32
  dot1wPortTxConfigBpduCount Counter32
  dot1wPortTxTcnBpduCount Counter32
  dot1wPortInvalidRstBpduRxCount Counter32
  dot1wPortInvalidConfigBpduRxCount Counter32
  dot1wPortInvalidTcnBpduRxCount Counter32
  dot1wPortProtocolMigrationCount Counter32
  dot1wPortEffectivePortState TruthValue
  dot1wPortAutoEdge TruthValue
  dot1wPortRestrictedRole TruthValue
  dot1wPortRestrictedTCN TruthValue

TabDot1wRstTrapsControlEntry  
SEQUENCE    
  dot1wSetTraps Integer32
  dot1wGenTrapType INTEGER

TabDot1wPortTrapNotificationEntry  
SEQUENCE    
  dot1wPortTrapIndex Integer32
  dot1wPortMigrationType INTEGER
  dot1wPktErrType INTEGER
  dot1wPktErrVal Integer32
  dot1wPortRoleType INTEGER
  dot1wOldRoleType INTEGER

TabDot1qVlanGlobalsEntry  
SEQUENCE    
  dot1qVlanGlobalsContextId Integer32
  dot1qGarpShutdownStatus TruthValue
  dot1qVlanDebug Integer32
  dot1qVlanLearningMode INTEGER
  dot1qVlanOperStatus EnabledStatus
  dot1qGvrpOperStatus EnabledStatus

TabPortBaseVlanCurrentEntry  
SEQUENCE    
  portBaseVlanIndex Integer32
  portBaseVlanName OCTET STRING
  portBaseVlanCurrentEgressPorts PortList
  portBaseVlanStatus INTEGER
  portBaseVlanCreationTime TimeTicks
  portBaseVlanRowStatus RowStatus

TabPortBaseStaticUnicastEntry  
SEQUENCE    
  portBaseStaticUnicastIndex Integer32
  portBaseStaticUnicastVlanIndex Integer32
  portBaseStaticUnicastAddress MacAddress
  portBaseStaticUnicastAllowedToGoTo PortList
  portBaseStaticUnicastStatus INTEGER
  portBaseStaticUnicastRowStatus RowStatus

TabPortBaseStaticMulticastEntry  
SEQUENCE    
  portBaseStaticMulticastIndex Integer32
  portBaseStaticMulticastVlanIndex Integer32
  portBaseStaticMulticastAddress MacAddress
  portBaseStaticMulticastStaticEgressPorts PortList
  portBaseStaticMulticastStatus INTEGER
  portBaseStaticMulticastRowStatus RowStatus

FsLldpLocPortEntry  
SEQUENCE    
  fsLldpLocPortIdSubtype INTEGER
  fsLldpLocPortId OCTET STRING
  fsLldpPortConfigNotificationType INTEGER

VoiceVlanPortControlEntry  
SEQUENCE    
  voicevlanPortControlIndex InterfaceIndex
  voicevlanPortAutoDetection INTEGER
  voicevlanPortState INTEGER

VoicevlanOUIEntry  
SEQUENCE    
  voicevlanOUITelephonyOUI MacAddress
  voicevlanOUIDescription OCTET STRING
  voicevlanOUIMask MacAddress
  voicevlanOUIStatus RowStatus

TrafficSegEntry  
SEQUENCE    
  trafficSegIfIndex InterfaceIndex
  trafficSegMemberList PortList

AtiAclClassifierEntry  
SEQUENCE    
  atiAclClassifierIndex Integer32
  atiAclClassifierSrcMac MacAddress
  atiAclClassifierSrcMacMaskLen Integer32
  atiAclClassifierDstMac MacAddress
  atiAclClassifierDstMacMaskLen Integer32
  atiAclClassifierVlanId Integer32
  atiAclClassifierCos Integer32
  atiAclClassifierEtherType Integer32
  atiAclClassifierSrcIp IpAddress
  atiAclClassifierSrcIpMaskLen Integer32
  atiAclClassifierDstIp IpAddress
  atiAclClassifierDstIpMaskLen Integer32
  atiAclClassifierDscp Integer32
  atiAclClassifierProtocol Integer32
  atiAclClassifierSrcPort Integer32
  atiAclClassifierDstPort Integer32
  atiAclClassifierRowStatus RowStatus

AtiAclProfileActionEntry  
SEQUENCE    
  atiAclProfileActionIndex Integer32
  atiAclProfileActionCos Integer32
  atiAclProfileActionDscp Integer32
  atiAclProfileActionRowStatus RowStatus

AtiAclInProfileActionEntry  
SEQUENCE    
  atiAclInProfileActionIndex Integer32
  atiAclInProfileActionPermitDeny Integer32
  atiAclInProfileActionActionId Integer32
  atiAclInProfileActionRowStatus RowStatus

AtiAclOutProfileActionEntry  
SEQUENCE    
  atiAclOutProfileActionIndex Integer32
  atiAclOutProfileActionPermitDeny Integer32
  atiAclOutProfileActionCommittedRate Integer32
  atiAclOutProfileActionBurstSize Integer32
  atiAclOutProfileActionActionId Integer32
  atiAclOutProfileActionRowStatus RowStatus

AtiAclPortListEntry  
SEQUENCE    
  atiAclPortListIndex Integer32
  atiAclPortListString DisplayString
  atiAclPortListRowStatus RowStatus

AtiAclPolicyEntry  
SEQUENCE    
  atiAclPolicyIndex Integer32
  atiAclPolicyClassifierIndex Integer32
  atiAclPolicySequence Integer32
  atiAclPolicyInProfileIndex Integer32
  atiAclPolicyOutProfileIndex Integer32
  atiAclPolicyPortListIndex Integer32
  atiAclPolicyRowStatus RowStatus

AtiDstMacFilterEntry  
SEQUENCE    
  atiDstMacFilterIndex Integer32
  atiDstMacFilterAddress MacAddress
  atiDstMacFilterRowStatus RowStatus

TabDhcpSnoopVLANSettingEntry  
SEQUENCE    
  dhcpSnoopVLANSettingVID Unsigned32
  dhcpSnoopVLANSettingStatus INTEGER

TabDhcpSnoopPortSettingEntry  
SEQUENCE    
  dhcpSnoopPortSettingIndex Integer32
  dhcpSnoopPortSettingStatus INTEGER

TabDhcpSnoopBindindDatabaseEntry  
SEQUENCE    
  dhcpSnoopBindindDBMacAddress MacAddress
  dhcpSnoopBindindDBVLANID Unsigned32
  dhcpSnoopBindindDBIPAddress IpAddress
  dhcpSnoopBindindDBPortNumber Integer32
  dhcpSnoopBindindDBType INTEGER
  dhcpSnoopBindindDBLeaseTime Unsigned32
  dhcpSnoopBindindDBRowStatus RowStatus

Defined Values

at-GS95024v3 1.3.6.1.4.1.207.1.4.167
Private MIB for AT-GS950 Series Switches
MODULE-IDENTITY    

l2Snmp 1.3.6.1.4.1.207.1.4.167.1
OBJECT IDENTIFIER    

l2Radius 1.3.6.1.4.1.207.1.4.167.25
OBJECT IDENTIFIER    

l2Cfa 1.3.6.1.4.1.207.1.4.167.27
OBJECT IDENTIFIER    

l2Rmon 1.3.6.1.4.1.207.1.4.167.44
OBJECT IDENTIFIER    

l2La 1.3.6.1.4.1.207.1.4.167.63
OBJECT IDENTIFIER    

l2Pnac 1.3.6.1.4.1.207.1.4.167.64
OBJECT IDENTIFIER    

l2System 1.3.6.1.4.1.207.1.4.167.81
OBJECT IDENTIFIER    

l2Dfs 1.3.6.1.4.1.207.1.4.167.83
OBJECT IDENTIFIER    

l2Syslog 1.3.6.1.4.1.207.1.4.167.89
OBJECT IDENTIFIER    

l2Security 1.3.6.1.4.1.207.1.4.167.95
OBJECT IDENTIFIER    

l2Ssl 1.3.6.1.4.1.207.1.4.167.96
OBJECT IDENTIFIER    

l2Ssh 1.3.6.1.4.1.207.1.4.167.97
OBJECT IDENTIFIER    

l2Sntp 1.3.6.1.4.1.207.1.4.167.99
OBJECT IDENTIFIER    

l2Dscp 1.3.6.1.4.1.207.1.4.167.100
OBJECT IDENTIFIER    

l2Snoop 1.3.6.1.4.1.207.1.4.167.105
OBJECT IDENTIFIER    

l2Bridge 1.3.6.1.4.1.207.1.4.167.116
OBJECT IDENTIFIER    

l2Mst 1.3.6.1.4.1.207.1.4.167.118
OBJECT IDENTIFIER    

l2Rst 1.3.6.1.4.1.207.1.4.167.119
OBJECT IDENTIFIER    

l2Vlan 1.3.6.1.4.1.207.1.4.167.120
OBJECT IDENTIFIER    

fslldp 1.3.6.1.4.1.207.1.4.167.158
OBJECT IDENTIFIER    

l2VoiceVlan 1.3.6.1.4.1.207.1.4.167.163
OBJECT IDENTIFIER    

trafficSeg 1.3.6.1.4.1.207.1.4.167.165
OBJECT IDENTIFIER    

atiAclMib 1.3.6.1.4.1.207.1.4.167.166
OBJECT IDENTIFIER    

l2DhcpSnoop 1.3.6.1.4.1.207.1.4.167.181
OBJECT IDENTIFIER    

dot1dPBridge 1.3.6.1.4.1.207.1.4.167.116.6
OBJECT IDENTIFIER    

dot1qQBridge 1.3.6.1.4.1.207.1.4.167.116.7
OBJECT IDENTIFIER    

sysSnmpUser 1.3.6.1.4.1.207.1.4.167.1.1
OBJECT IDENTIFIER    

sysSnmpGroup 1.3.6.1.4.1.207.1.4.167.1.2
OBJECT IDENTIFIER    

sysSnmpGroupAccess 1.3.6.1.4.1.207.1.4.167.1.3
OBJECT IDENTIFIER    

sysSnmpViewTree 1.3.6.1.4.1.207.1.4.167.1.4
OBJECT IDENTIFIER    

sysSnmpCommunity 1.3.6.1.4.1.207.1.4.167.1.5
OBJECT IDENTIFIER    

sysSnmpTrapManager 1.3.6.1.4.1.207.1.4.167.1.6
OBJECT IDENTIFIER    

sysSnmpEngineID 1.3.6.1.4.1.207.1.4.167.1.7
An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the value of the snmpEngineID of a remote SNMP engine with which this user can communicate.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpEngineID  

snmpGlobalState 1.3.6.1.4.1.207.1.4.167.1.8
This object is for enabling or disabling SNMP Community function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysSnmpUserTable 1.3.6.1.4.1.207.1.4.167.1.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnmpUserEntry

sysSnmpUserEntry 1.3.6.1.4.1.207.1.4.167.1.1.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnmpUserEntry  

sysSnmpUserName 1.3.6.1.4.1.207.1.4.167.1.1.1.1.1
A human readable string rsysresenting the name of the user. This is the (User-based Security) Model dependent security ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sysSnmpUserAuthProtocol 1.3.6.1.4.1.207.1.4.167.1.1.1.1.2
An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same concsystual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of UserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoAuthProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoAuthProtocol, then an 'inconsistentValue' error must be returned. If a set operation tries to set the value to the NoAuthProtocol while the UserPrivProtocol value in the same row is not equal to NoPrivProtocol, then an 'inconsistentValue' error must be returned. That means that an SNMP command generator application must first ensure that the UserPrivProtocol is set to the NoPrivProtocol value before it can set the UserAuthProtocol value to NoAuthProtocol.
Status: current Access: read-create
OBJECT-TYPE    
  AutonomousType  

sysSnmpUserPrivProtocol 1.3.6.1.4.1.207.1.4.167.1.1.1.1.3
An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same concsystual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of usmUserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoPrivProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoPrivProtocol, then an 'inconsistentValue' error must be returned. Note that if any privacy protocol is used, then you must also use an authentication protocol. In other words, if usmUserPrivProtocol is set to anything else than NoPrivProtocol, then the corresponding instance of usmUserAuthProtocol cannot have a value of usmNoAuthProtocol. If it does, then an 'inconsistentValue' error must be returned.
Status: current Access: read-create
OBJECT-TYPE    
  AutonomousType  

sysSnmpUserStatus 1.3.6.1.4.1.207.1.4.167.1.1.1.1.4
The status of this concsystual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this concsystual row can be modified, excsyst for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysSnmpGroupTable 1.3.6.1.4.1.207.1.4.167.1.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnmpGroupEntry

sysSnmpGroupEntry 1.3.6.1.4.1.207.1.4.167.1.2.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnmpGroupEntry  

sysSnmpSecurityModel 1.3.6.1.4.1.207.1.4.167.1.2.1.1.1
A human readable string rsysresenting the name of the user. This is the (User-based Security) Model dsysendent security ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpSecurityModel  

sysSnmpSecurityName 1.3.6.1.4.1.207.1.4.167.1.2.1.1.2
A human readable string rsysresenting the name of the user. This is the (User-based Security) Model dsysendent security ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sysSnmpGroupName 1.3.6.1.4.1.207.1.4.167.1.2.1.1.3
The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sysSnmpGroupStatus 1.3.6.1.4.1.207.1.4.167.1.2.1.1.4
The status of this concsystual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this concsystual row can be modified, excsyst for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysSnmpGroupAccessTable 1.3.6.1.4.1.207.1.4.167.1.3.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnmpGroupAccessEntry

sysSnmpGroupAccessEntry 1.3.6.1.4.1.207.1.4.167.1.3.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnmpGroupAccessEntry  

sysSnmpaccessGroupIndex 1.3.6.1.4.1.207.1.4.167.1.3.1.1.1
The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sysSnmpaccessSecurityModel 1.3.6.1.4.1.207.1.4.167.1.3.1.1.2
In order to gain the access rights allowed by this concsystual row, this securityModel must be in use.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpSecurityModel  

sysSnmpaccessSecurityLevel 1.3.6.1.4.1.207.1.4.167.1.3.1.1.3
The minimum level of security required in order to gain the access rights allowed by this concsystual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If multiple entries are equally indexed excsyst for this vacmAccessSecurityLevel index, then the entry which has the highest value for vacmAccessSecurityLevel is selected.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpSecurityLevel  

sysSnmpaccessReadViewName 1.3.6.1.4.1.207.1.4.167.1.3.1.1.4
The value of an instance of this object identifies the MIB view of the SNMP context to which this concsystual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

sysSnmpaccessWriteViewName 1.3.6.1.4.1.207.1.4.167.1.3.1.1.5
The value of an instance of this object identifies the MIB view of the SNMP context to which this concsystual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

sysSnmpaccessNotifyViewName 1.3.6.1.4.1.207.1.4.167.1.3.1.1.6
The value of an instance of this object identifies the MIB view of the SNMP context to which this concsystual row authorizes access for notifications. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

sysSnmpaccessStatus 1.3.6.1.4.1.207.1.4.167.1.3.1.1.7
The status of this concsystual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this concsystual row can be modified.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysSnmpViewTreeTable 1.3.6.1.4.1.207.1.4.167.1.4.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnmpViewTreeEntry

sysSnmpViewTreeEntry 1.3.6.1.4.1.207.1.4.167.1.4.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnmpViewTreeEntry  

sysSnmpviewTreeName 1.3.6.1.4.1.207.1.4.167.1.4.1.1.1
The human readable name for a family of view subtrees.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sysSnmpviewTreeSubtree 1.3.6.1.4.1.207.1.4.167.1.4.1.1.2
The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees.
Status: current Access: not-accessible
OBJECT-TYPE    
  OBJECT IDENTIFIER  

sysSnmpviewTreeMask 1.3.6.1.4.1.207.1.4.167.1.4.1.1.3
The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub-identifier of vacmViewTreeFamilySubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if, for each sub-identifier of the value of vacmViewTreeFamilySubtree, either: the i-th bit of vacmViewTreeFamilyMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of vacmViewTreeFamilySubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of vacmViewTreeFamilySubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of vacmViewTreeFamilySubtree. Note that masks of length greater than zero length do not need to be supported. In this case this object is made read-only.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

sysSnmpviewTreeType 1.3.6.1.4.1.207.1.4.167.1.4.1.1.4
Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or excluded from the MIB view.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER included(1), excluded(2)  

sysSnmpviewTreeStatus 1.3.6.1.4.1.207.1.4.167.1.4.1.1.5
The status of this concsystual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this concsystual row can be modified.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysSnmpCommunityTable 1.3.6.1.4.1.207.1.4.167.1.5.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnmpCommunityEntry

sysSnmpCommunityEntry 1.3.6.1.4.1.207.1.4.167.1.5.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnmpCommunityEntry  

sysSnmpsnmpCommunityIndex 1.3.6.1.4.1.207.1.4.167.1.5.1.1.1
The unique index value of a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sysSnmpsnmpCommunityName 1.3.6.1.4.1.207.1.4.167.1.5.1.1.2
The unique index value of a row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sysSnmpsnmpCommunityPolicy 1.3.6.1.4.1.207.1.4.167.1.5.1.1.3
A human readable string rsysresenting the corresponding value of snmpCommunityName in a Security Model indsysendent format.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sysSnmpsnmpCommunityStatus 1.3.6.1.4.1.207.1.4.167.1.5.1.1.4
The status of this concsystual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpCommunityName and snmpCommunitySecurityName objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpCommunityStatus is active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysSnmpTrapManagerTable 1.3.6.1.4.1.207.1.4.167.1.6.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnmpTrapManagerEntry

sysSnmpTrapManagerEntry 1.3.6.1.4.1.207.1.4.167.1.6.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnmpTrapManagerEntry  

sysSnmpsnmpTrapManagerName 1.3.6.1.4.1.207.1.4.167.1.6.1.1.1
The locally arbitrary, but unique identifier associated with this snmpNotifyEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sysSnmpsnmpTrapManagerAddress 1.3.6.1.4.1.207.1.4.167.1.6.1.1.2
This object contains a transport address. The format of this address dsysends on the value of the snmpTargetAddrTDomain object.
Status: current Access: read-create
OBJECT-TYPE    
  TAddress  

sysSnmpsnmpTrapManagerSecurityLevel 1.3.6.1.4.1.207.1.4.167.1.6.1.1.3
The Level of Security to be used when generating SNMP messages using this entry.
Status: current Access: read-create
OBJECT-TYPE    
  L2snmpLevel  

sysSnmpsnmpTrapManagerStatus 1.3.6.1.4.1.207.1.4.167.1.6.1.1.4
The status of this concsystual row in the SnmpTrapManagerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpTrapManagerName, snmpTrapManagerAddress and snmpTrapManagerSecurityLevel objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpTrapManagerStatus is active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysRadiusExtClient 1.3.6.1.4.1.207.1.4.167.25.1
OBJECT IDENTIFIER    

sysRadiusExtServerTable 1.3.6.1.4.1.207.1.4.167.25.1.3
The (concsystual) table listing the RADIUS servers with which the client shares a secret.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabRadiusExtServerEntry

sysRadiusExtServerEntry 1.3.6.1.4.1.207.1.4.167.25.1.3.1
An entry (concsystual row) rsysresenting a RADIUS server with which the client shares a secret.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabRadiusExtServerEntry  

sysRadiusExtServerIndex 1.3.6.1.4.1.207.1.4.167.25.1.3.1.1
The RADIUS server with whom the client interacts.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

sysRadiusExtServerAddress 1.3.6.1.4.1.207.1.4.167.25.1.3.1.2
The IP address of the RADIUS server referred to in this table entry.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysRadiusExtServerSharedSecret 1.3.6.1.4.1.207.1.4.167.25.1.3.1.4
The secret string which is shared between Server and Client
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

sysRadiusExtServerResponseTime 1.3.6.1.4.1.207.1.4.167.25.1.3.1.6
The maximum time within which the server has to respond for a request from the client
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..120  

sysRadiusExtServerMaximumRetransmission 1.3.6.1.4.1.207.1.4.167.25.1.3.1.7
The allowed maximum no. of trials to be tried by a client to get response from the server for a request
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..254  

sysRadiusExtServerAuthPortNum 1.3.6.1.4.1.207.1.4.167.25.1.3.1.8
The UDP port the client is using to send authentication requests to this server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

sysRadiusExtServerEntryStatus 1.3.6.1.4.1.207.1.4.167.25.1.3.1.9
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysRadiusExtServerAccPort 1.3.6.1.4.1.207.1.4.167.25.1.3.1.10
The UDP port the client is using to send accounting requests to this server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

if 1.3.6.1.4.1.207.1.4.167.27.1
OBJECT IDENTIFIER    

traps 1.3.6.1.4.1.207.1.4.167.27.4
OBJECT IDENTIFIER    

ifMaxInterfaces 1.3.6.1.4.1.207.1.4.167.27.1.1
Specifies the maximum number of interfaces that can be present in the system.
Status: deprecated Access: read-write
OBJECT-TYPE    
  InterfaceIndex  

ifMaxPhysInterfaces 1.3.6.1.4.1.207.1.4.167.27.1.2
Specifies the maximum number of physical interfaces that can be present in the system.
Status: deprecated Access: read-write
OBJECT-TYPE    
  InterfaceIndex  

ifAvailableIndex 1.3.6.1.4.1.207.1.4.167.27.1.3
Shows an ifIndex which is available for creation of any new virtual (non-physical) interface in the system. This ifIndex value can be used for creation of interfaces in the ifMainTable or any media-specif MIB. For creation of physical interfaces, any free ifIndex between 1 and ifMaxPhysInterfaces can be used.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

ifMainTable 1.3.6.1.4.1.207.1.4.167.27.1.4
A list of all the interface entries in the system. This table contains objects which are applicable to all types of interfaces in the system. This table is a proprietary extension to the standard ifTable and ifXTable. The index to this table has the semantics of the MIB-2 ifIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabIfMainEntry

ifMainEntry 1.3.6.1.4.1.207.1.4.167.27.1.4.1
An entry containing management information applicable to a particular interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabIfMainEntry  

ifMainIndex 1.3.6.1.4.1.207.1.4.167.27.1.4.1.1
A unique value, greater than zero, for each interface. This object is identical to the ifIndex of the standard MIB-2 ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

ifMainType 1.3.6.1.4.1.207.1.4.167.27.1.4.1.2
The type/protocol of interface. Specification of the object is mandatory for all interfaces. This value should be specified after the row creation in the ifMainTable and before setting any other object in this table. Once the type is specified, it cannot be changed - the interface should be deleted for changing the type of the interface. The ethernetCsmacd(6), iso88025TokenRing(9), aal5(49), async(84) and hdlc(118) are physical interfaces while all other types are virtual or logical interfaces. For creation of physical interface types, it is mandatory to specify the handle to the device driver using the ifAlias object of the standard ifXTable before specifying the type. This handle could be something like eth1 or /dev/abcd.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER rfc877x25(5), ethernetCsmacd(6), iso88025TokenRing(9), ppp(23), softwareLoopback(24), frameRelay(32), miox25(38), aal5(49), async(84), frameRelayMPI(92), pppMultilinkBundle(108), ipOverAtm(114), hdlc(118), tunnel(131), atmSubInterface(134), l2macvlan(135), l3ipvlan(136), mplsTunnel(150), ieee8023ad(161), mpls(166)  

ifMainMtu 1.3.6.1.4.1.207.1.4.167.27.1.4.1.3
The MTU for the interface as shown to the higher interface sub-layer (this value should not include the encapsulation or header added by the interface). If IP is operating over the interface, then this value indicates the IP MTU over this interface. For changing the MTU of any interface, the interface must be brought down first - changing MTU while the interface is administratively up is not permitted. If not specified during interface creation, a default value is assigned based on the ifMainType given to the particular interface. While configuring for logical VLAN interfaces, care should be taken to, configure this value as the lowest of the MTU values of the member ports.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

ifMainAdminStatus 1.3.6.1.4.1.207.1.4.167.27.1.4.1.4
The desired state of the interface. This object can be set only when the ifMainRowStatus of the interface is active. This object has the semantics of the ifAdminStatus of the standard ifTable. The testing(3) state indicates that no operational packets can be passed - this state is not currently supported. When a managed system initializes, all interfaces start with ifMainAdminStatus in the down(2) state, it's a default state also. As a result of either explicit management action or per configuration information retained by the managed system, ifMainAdminStatus is then changed to the up (1) state (or remains in the down(2) state).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

ifMainOperStatus 1.3.6.1.4.1.207.1.4.167.27.1.4.1.5
The current operational state of the interface. The testing (3) state indicates that no operational packets can be passed - this state is not supported currently. If ifMainAdminStatus is down (2) then ifMainOperStatus would be down (2). If ifMainAdminStatus is changed to up (1) then ifMainOperStatus should change to up (1) if the interface is ready to transmit and receive work traffic; it should change to dormant (5) the interface is waiting for external actions (such as a serial line waiting for an incoming connection); it should change to lowerLayerDown(7) state if it cannot be made up as the interface sub-layer below it is down; it should remain in the down (2) state if and only if there is a fault that prevents it from going to the up (1) state; it should remain in the notPresent (6) state if the interface has missing (typically, hardware) components. The status unknown(4) is shown when it is not possible to determine the exact status of the interface - e.g. the interface sub-layer is performing negotiations - during this period the interface is not up but at the same time, it is not a fault condition and hence it cannot be shown as down - in such periods the status is shown as unknown. This object has the semantics of the ifOperStatus of the standard ifTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3), unknown(4), dormant(5), notPresent(6), lowerLayerDown(7)  

ifMainEncapType 1.3.6.1.4.1.207.1.4.167.27.1.4.1.6
The encapsulation type to be used over the interface. For Ethernet interfaces, the default encapsulation type is ethernetV2(8). The other possible encapsulation is llcSnap(6). If other(1) is specified then an automatic encapsulation type learning method is used in ARP for determining the encapsulation for unicast destinations while the multicast and broadcast destinations use ethernetV2(8). For PPP and MLPPP interfaces, the encapsulation type can only be other(1) and this is the default value. For FR VCs, the value can be nlpid(2) (for carrying protocols which have NLPID) or nlpidSnap(3) (for other protocols). The default is nlpid(2) and the types of protocols supported are inferred from the stack-layering implemented over the interface. For X.25 VCs, the value can be nlpid(2) or nlpidSnap(3) (where the VC can carry multiplexed protocol traffic with each data packet containing the NLPID or SNAP header) or cudNlpid(4) or cudNlpidSnap(5) (where the CUD specifies the NLPID of the protocol or SNAP and the data packets do not contain these headers - for dedicated VCs). The default is cudNlpid(4). For ATM VCs, the default is llcSnap(6) but the vcMultiplexed(7) encapsulation is also supported. This object is not applicable to other interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), nlpid(2), nlpidSnap(3), cudNlpid(4), cudNlpidSnap(5), llcSnap(6), vcMultiplexed(7), ethernetV2(8)  

ifMainBrgPortType 1.3.6.1.4.1.207.1.4.167.27.1.4.1.7
The Bridge port type of this specified externally accessible port. Bridge Port type can be specified only for switch ports and not for router ports. providerNetworkPort - Port Connected to a single Provider. SVLAN Classification is based on only the PVID configured for the port for untagged packets. customerNetworkPortPortBased - Port in the S-VLAN component that can transmit or received frames for single customer. All packets received on this port, are mapped to one single service instance identified by the PVID of that Port. Accsystable Port Type will be always Admit only Untagged or Priority Tagged Frames on this port. customerNetworkPortStagged - Port in the S-VLAN component that can transmit or received frames for single customer. VLAN classification on this interface will be based on the S-tag received or on the PVID of the port. Ingress Filtering will be always enabled on this port. customerEdgePort - Port in a Provider Edge Bridge connected to a single customer. Multiple services can be provide on this port. The Packets received on this interface will be first classified to a CVLAN. CVLAN classification can be based on the Vid in the C-Tag present in the packet (if it C-tagged packet) or from the pvid of the port. Service instance selection (S-VLAN selection) for a frame is done based on the entry present in the C-VID registration table for the pair (C-VID, recsystion Port). CustomerEdgePort configuration is allowed only in Provider Edge Bridges. propCustomerEdgePort - Port connected to a single customer, where multiple services can be provided based on only Proprietary SVLAN classification tables. S-VLAN classification will not happen based on C-VID registration table on this port. propCustomerEdgePort configuration is allowed only in Provider Edge Bridges. propCustomerNetworkPort - Port connected to a single customer, where multiple service can be provided based on CVLANs by assigning one of the Proprietary SVLAN classification tables to this port. The services can also be assigned using other proprietary SVLAN classification tables where CVLAN is not the index of the table. propProviderNetworkPort - Port connected to a Q-in-Q Bridge located inside Provider Network. This port is part of S-VLAN component. If packets to be tagged and sent out of this port will have 0x8100 as the ether type. Similarly pakcets with standard Q tag (ether type as 0x8100) received will be considered as S-Tagged packets. customerBridgePort - Type of the port to be used in customer bridges as well in Provider(Q-in-Q) bridges. This type is not valid in Provider Core bridges as well as Provider Edge bridge. In Customer bridges and in Provider Bridges only customerPort option is allowed. Bridge Port Type cannot be set for a port-channel port, if some physical ports are aggregated in it. Also Bridge Port type cannot be set for a port, if part of a port-channel. Whenever the Bridge port type changes, the previous configuration associated with the port will be flushed. For example. whenever CNP(STagged) and PNP port types are changed to any other port type, - The unicast entries learnt on this port and - The VID translation table entries associated with the port will be flushed. Whenever CEP port type is changed to any other port type, - The unicast entries learnt on this port - The C-VID registration table entries associated with the port - The PEP configuration table entries - The service priority regeneration table entries will be flushed. Even the vlan membership of the port will be removed when the Pbport type is changed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER providerNetworkPort(1), customerNetworkPortPortBased(2), customerNetworkPortStagged(3), customerEdgePort(4), propCustomerEdgePort(5), propCustomerNetworkPort(6), propProviderNetworkPort(7), customerBridgePort(8)  

ifMainRowStatus 1.3.6.1.4.1.207.1.4.167.27.1.4.1.8
A RowStatus variable for addition, deletion and in-activation of the interfaces. Specification of the object is mandatory for all interfaces. When the status is active, the interface is created and ready to use in the respective protocol modules. When the status is notInService, the interface has not been registered with the respective protocol modules and as such those modules are not aware of the existence of the interface - creation is hence, incomplete. Setting an active interface to notInService results in de-registration/deletion of the interface from the respective protocol modules and all the configurations associated with that interface in those modules may be lost. Deletion of an interface, may affect the status of other interfaces which are layered above or below it in the Interface Stack (ifStackTable) and may result in other interfaces being made notReady or notInService.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ifIpTable 1.3.6.1.4.1.207.1.4.167.27.1.5
A list of all the interface entries in the system which are registered with IP. This table contains objects which are applicable for the management of IP over the network interfaces in the system. This table is a extension to the ifMainTable. The index to this table has the semantics of the ifMainIndex of the ifMainTable. Entries are created automatically in this table for any interface sub-layer which is layer below IP using the ifStackTable. Similarly, entries are deleted from this table when the interface's layering below IP is removed.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabIfIpEntry

ifIpEntry 1.3.6.1.4.1.207.1.4.167.27.1.5.1
An entry containing management information applicable to a particular interface over which IP is operating.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabIfIpEntry  

ifIpAddrAllocMethod 1.3.6.1.4.1.207.1.4.167.27.1.5.1.1
The mechanism to be used for allocation of IP address for this interface. The value negotiation can be used only for PPP and MLPPP interfaces which support obtaining of IP addresses through negotiation. The dynamic(3) option takes an IP address dynamically from the available server (dhcp/bootp/rarp) according to the protocol specified in ifIpAddrAllocProtocol. If the method specified is manual and the IP address is not provided (then the interface would be treated as a un-numbered interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER manual(1), negotiation(2), dynamic(3), none(4)  

ifIpAddr 1.3.6.1.4.1.207.1.4.167.27.1.5.1.2
Specifies the IP address given to this interface. The specification of this object is mandatory for all network interfaces (Ethernet, FR VC, IPoA interface, PPP link - not under MP, MP interface and X.25 VC). If the interface is not a network interface then the default value of 0.0.0.0 is assigned and the interface is treated as a un-numbered interface by IP.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ifIpSubnetMask 1.3.6.1.4.1.207.1.4.167.27.1.5.1.3
Specifies the IP Subnet Mask for this interface. The value should be specified only for network interfaces and any valid VLSM is accsysted. If not specified, this object takes the default subnet mask value based on the class of the IP address configured for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ifIpBroadcastAddr 1.3.6.1.4.1.207.1.4.167.27.1.5.1.4
Specifies the IP broadcast address for this interface. The value should be specified only for network interfaces and any valid broadcast address based on a valid VLSM is accsysted. If not specified, this object takes the default value based on the class of the IP address configured for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ifIpForwardingEnable 1.3.6.1.4.1.207.1.4.167.27.1.5.1.5
Specifies whether IP forwarding is enable on this interface. Disabling IP forwarding on an interface will result in packets which are to be forwarded on that interface being dropped and ICMP error messages being generated for the packets.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ifIpAddrAllocProtocol 1.3.6.1.4.1.207.1.4.167.27.1.5.1.6
Specifies the protocol to be used to obtain IP address for this interface. This object is valid only when ifIpAddrAllocMethod is set to dynamic (3). Currently rarp (1) option is not supported. The assigned value will be effective only when the interface admin status changes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), rarp(1), dhcp(2), bootp(3)  

ifIvrTable 1.3.6.1.4.1.207.1.4.167.27.1.8
A list of all the interfaces in the system with IVR related configurations. This table is an extension to the ifMainTable. The index to this table has the semantics of the ifMainIndex of the ifMainTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabIfIvrEntry

ifIvrEntry 1.3.6.1.4.1.207.1.4.167.27.1.8.1
An entry containing IVR-related information applicable to a interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabIfIvrEntry  

ifIvrBridgedIface 1.3.6.1.4.1.207.1.4.167.27.1.8.1.1
Indicates if this interface is a Bridged interface or not. A value of 'TRUE' indicates that this interface is a Bridged interface and is capable of performing bridging of packets through this interface. A value of 'FALSE' indicates that this interface is a Routed interface and is capable of performing routing of packets through this interface.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ifSetMgmtVlanList 1.3.6.1.4.1.207.1.4.167.27.1.9
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanId values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanId value in that octet. This is the set of vlans configured by management to associate with the management interface.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

ifResetMgmtVlanList 1.3.6.1.4.1.207.1.4.167.27.1.10
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanId values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanId value in that octet. This is the set of vlans configured by management to dis-associate from the management interface. Get operation is not allowed for this object.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

ifSecondaryIpAddressTable 1.3.6.1.4.1.207.1.4.167.27.1.11
A list of secondary IP addresses configured over the interfaces registered with IP. This table is a extension to the ifMainTable. The index to this table has the semantics of the ifMainIndex of the ifMainTable. Secondary IpAddress configuration should not override the primary ip address configured for any of the interface Updation of entries in this table are not allowd when RowStatus is active
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabIfSecondaryIpAddressEntry

ifSecondaryIpAddressEntry 1.3.6.1.4.1.207.1.4.167.27.1.11.1
An entry contains the information associated with the secondary(additional) ip address configured to a particular interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabIfSecondaryIpAddressEntry  

ifSecondaryIpAddress 1.3.6.1.4.1.207.1.4.167.27.1.11.1.1
Specifies the Secondary IP address associated with the interface
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

ifSecondaryIpSubnetMask 1.3.6.1.4.1.207.1.4.167.27.1.11.1.2
Specifies the IP Subnet Mask associted with the secondary ip address configuration. The value should be specified only for network interfaces and any valid VLSM is accsysted. If not specified, this object takes the default subnet mask value based on the class of the IP address configured for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ifSecondaryIpBroadcastAddr 1.3.6.1.4.1.207.1.4.167.27.1.11.1.3
Specifies the IP broadcast address associated with the configured secondary IP address. The value should be specified only for network interfaces and any valid broadcast address based on a valid VLSM is accsysted. If not specified, this object takes the default value based on the class of the IP address configured for the interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

ifSecondaryIpRowStatus 1.3.6.1.4.1.207.1.4.167.27.1.11.1.4
This object is used to manage creation and deletion of rows in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysRmonEnableStatus 1.3.6.1.4.1.207.1.4.167.44.2
This object defines the sysRmonenable flag for sysRmon
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER sysRmonenabled(1), sysRmondisabled(2)  

sysRmonHwStatsSupp 1.3.6.1.4.1.207.1.4.167.44.3
This object defines the flag for whether HW supports Etherstatistics or not
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notsupported(0), supported(1)  

sysRmonHwHistorySupp 1.3.6.1.4.1.207.1.4.167.44.4
This object defines the enabled HWhistorysupp flag for sysRmon
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notsupported(0), supported(1)  

sysRmonHwAlarmSupp 1.3.6.1.4.1.207.1.4.167.44.5
This object defines the enabled HWAlarmsupp flag for sysRmon
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notsupported(0), supported(1)  

sysRmonHwEventSupp 1.3.6.1.4.1.207.1.4.167.44.9
This object defines the enabled HWEvent flag for sysRmon
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notsupported(0), supported(1)  

sysLaSystem 1.3.6.1.4.1.207.1.4.167.63.1
OBJECT IDENTIFIER    

sysLaPortChannel 1.3.6.1.4.1.207.1.4.167.63.2
OBJECT IDENTIFIER    

sysLaPort 1.3.6.1.4.1.207.1.4.167.63.3
OBJECT IDENTIFIER    

sysLaSystemControl 1.3.6.1.4.1.207.1.4.167.63.1.1
Start or shutdown Link Aggregation Module in the system When set as 'start',resources required by Link aggregation module are allocated & Link aggregation module starts running. When shutdown, all resources used by Link aggregation module will be released to the system
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER start(1), shutdown(2)  

sysLaStatus 1.3.6.1.4.1.207.1.4.167.63.1.2
Sets the Link Aggregation Module administrative status as enabled or disabled. The module can be enabled only when this object is set to 'enabled'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysLaTraceOption 1.3.6.1.4.1.207.1.4.167.63.1.3
This object is used to enable Trace Statements in Link Aggregation Module. A FOUR BYTE integer is used for enabling the level of tracing. Each BIT in the four byte integer, rsysresents a particular level of Trace. The mapping between the bit positions & the level of trace is as follows: 0 - Init and Shutdown Traces 1 - Management Traces 2 - Data Path Traces 3 - Control Plane Traces 4 - Packet Dump Traces 5 - Traces related to All Resources excsyst Buffers 6 - All Failure Traces 7 - Buffer Traces The remaining bits are unused. Combination of levels are also allowed. For example if the bits 0 and 1 are set, then the Trace statements related to Init-Shutdown and management will be printed. The user has to enter the corresponding INTEGER VALUE for the bits set. For example if bits 0 and 1 are set then user has to set the value 3.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysLaMaxPortsPerPortChannel 1.3.6.1.4.1.207.1.4.167.63.1.4
This Object specifies the maximun number of ports that can attach to a port-channel
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sysLaMaxPortChannels 1.3.6.1.4.1.207.1.4.167.63.1.5
This Object specifies the maximum number of Port-channels Present in the system
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sysLaOperStatus 1.3.6.1.4.1.207.1.4.167.63.1.6
This read only objects gives actual status of the Link Aggregation Module (Operational status of module). When Module is enabled Link Aggregation protocol starts functioning. When the module is disabled all the dynamically allocated memory will be freed and Link Aggregation protocol stops functioning.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysLaActorSystemID 1.3.6.1.4.1.207.1.4.167.63.1.7
A 6-octet read-write MAC address value used as a unique identifier for the System.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

sysLaPortChannelTable 1.3.6.1.4.1.207.1.4.167.63.2.1
A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabLaPortChannelEntry

sysLaPortChannelEntry 1.3.6.1.4.1.207.1.4.167.63.2.1.1
There is one entry in this table for each created port-channel port
Status: current Access: not-accessible
OBJECT-TYPE    
  TabLaPortChannelEntry  

sysLaPortChannelIfIndex 1.3.6.1.4.1.207.1.4.167.63.2.1.1.1
The ifIndex of the port-channel(Aggregator's interface index).
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

sysLaPortChannelGroup 1.3.6.1.4.1.207.1.4.167.63.2.1.1.2
An index that uniquely identifies an entry in this table.
Status: current Access: read-only
OBJECT-TYPE    
  LacpKey  

sysLaPortChannelAdminMacAddress 1.3.6.1.4.1.207.1.4.167.63.2.1.1.3
This object is used for configuring MacAddress that is to be used by the port-channel when sysLaPortChannelMacSelection is force. WARNING:The value configured should not conflict with the MAC address of system ports that are not configured to select this port-channel.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

sysLaPortChannelMacSelection 1.3.6.1.4.1.207.1.4.167.63.2.1.1.4
Indicates the MAC address selection method for for the port-channel. Dynamic - Port-channel MAC address is chosen as MAC address of an active port in the PortChannel. Force - Port-channel MAC address configured through sysLaPortChannelAdminMacAddress is used. The value can be changed to Force only after configuring a valid MAC address in sysLaPortChannelAdminMacAddress.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dynamic(1), force(2)  

sysLaPortChannelMode 1.3.6.1.4.1.207.1.4.167.63.2.1.1.5
Current Operating Channel Mode of the port Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  PortLaMode  

sysLaPortChannelPortCount 1.3.6.1.4.1.207.1.4.167.63.2.1.1.6
The number of ports actually configured to the port-channel
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sysLaPortChannelActivePortCount 1.3.6.1.4.1.207.1.4.167.63.2.1.1.7
This object will give the number of ports that are attached to the port-channel and actively carrying data traffic on the link.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sysLaPortChannelSelectionPolicy 1.3.6.1.4.1.207.1.4.167.63.2.1.1.8
Link selection policy to be used by the port-channel. The selection policies based on the IP address can be set if and only if hardware is present and supported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER macSrc(1), macDst(2), macSrcDst(3), ipSrc(4), ipDst(5), ipSrcDst(6), vlanId(7)  

sysLaPortChannelDefaultPortIndex 1.3.6.1.4.1.207.1.4.167.63.2.1.1.9
The ifIndex of the default port that gets attached to the aggregator. A value of 0 means there is no default port for this port-channel. If this object is set to 0, it will remove the current default port from the aggregator. To change the default port of an aggregator, first reset the object to 0 and then set the new ifIndex as default port.
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndexOrZero  

sysLaPortTable 1.3.6.1.4.1.207.1.4.167.63.3.1
A table that contains objects to set the port lacp mode of dot3adAggPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabLaPortEntry

sysLaPortEntry 1.3.6.1.4.1.207.1.4.167.63.3.1.1
Each entry in this table is for each physical port that participates in Link Aggregation which can be either aggregatable or individual. This table is indexed by the PortIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabLaPortEntry  

sysLaPortIndex 1.3.6.1.4.1.207.1.4.167.63.3.1.1.1
The ifIndex of the port
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

sysLaPortMode 1.3.6.1.4.1.207.1.4.167.63.3.1.1.2
This object is used to enable LACP, disable LACP or manually aggregate a port
Status: current Access: read-write
OBJECT-TYPE    
  PortLaMode  

sysLaPortBundleState 1.3.6.1.4.1.207.1.4.167.63.3.1.1.3
This read-only object is used to display the port state in aggregation upInBndl(0) - The port is operationally up and actively takes part in aggregation. standby(1) - The port is capable of joining in aggregation group, when any of the ports in aggregation group goes down. down(2) - The port is operationally down in lower layers. or the port is operational in lower layers but temporarily not able to participate in aggregation because of different partner information in the same group. upIndividual(3) - The port is operating individually and is not taking part in aggregation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER upInBndl(0), standby(1), down(2), upIndividual(3)  

sysLaPortActorResetAdminState 1.3.6.1.4.1.207.1.4.167.63.3.1.1.4
A string of 8 bits,corresponding to the administrative values of Actor_State as transmitted by the Actor in LACPDUs. The first bit corresponds to bit 0 of Actor_State (LACP_Activity), the second bit corresponds to bit 1 (LACP_Timeout),the third bit corresponds to bit 2 (Aggregation),the fourth bit corresponds to bit 3 (Synchronization),the fifth bit corresponds to bit 4 (Collecting),the sixth bit corresponds to bit 5 (Distributing), the seventh bit corresponds to bit 6 (Defaulted),and the eighth bit corresponds to bit 7 (Expired). This object allows the RESET of the values of Actor LACP_Activity, LACP_Timeout and Aggregation. Get operation on this object returns the current Port State of the Actor
Status: current Access: read-write
OBJECT-TYPE    
  LacpState  

sysLaPortAggregateWaitTime 1.3.6.1.4.1.207.1.4.167.63.3.1.1.5
Duration of the port to attach to the PortChannel.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

sysLaPortPartnerResetAdminState 1.3.6.1.4.1.207.1.4.167.63.3.1.1.6
A string of 8 bits,corresponding to the administrative values of Partner_State.The first bit corresponds to bit 0 of Partner_State (LACP_Activity),the second bit corresponds to bit 1 (LACP_Timeout), the third bit corresponds to bit 2 (Aggregation),the fourth bit corresponds to bit 3 (Synchronization),the fifth bit corresponds to bit 4 (Collecting),the sixth bit corresponds to bit 5 (Distributing), the seventh bit corresponds to bit 6 (Defaulted),and the eighth bit corresponds to bit 7 (Expired). This object allows the RESET of the values of Partner LACP_Activity, LACP_Timeout and Aggregation. Get operation on this object returns zeros for the Partner administrative values
Status: current Access: read-write
OBJECT-TYPE    
  LacpState  

sysLaPortActorAdminPort 1.3.6.1.4.1.207.1.4.167.63.3.1.1.7
The port number used as dot3adAggPortActorPort and is communicated in LACPDUs as the Actor_Port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sysLaPortRestoreMtu 1.3.6.1.4.1.207.1.4.167.63.3.1.1.8
The Restore mtu stores the original MTU of the port before getting aggregated to port channel. A SET on the MIB object is not allowed for SNMP users. This operation is allowed only during config-save-restore operation , during system initialization.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysLaPortSelectAggregator 1.3.6.1.4.1.207.1.4.167.63.3.1.1.9
This read-only object is used to display whether the port participates in dynamic aggregator selection. The default will be static aggregation selection. static(0) - The port is involved only in static aggregation. i.e. the port can be a member of only the aggregation to which it is configured. dynamic(1) - The port participates in dynamic aggregation selection. i.e. the port will be a part of best aggregation selected based on System id and Admin key. This object is set to 'dynamic' once the port is configured as a default port of a port channel.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER static(0), dynamic(1)  

sysPnacPaeSystem 1.3.6.1.4.1.207.1.4.167.64.1
OBJECT IDENTIFIER    

sysPnacAuthServer 1.3.6.1.4.1.207.1.4.167.64.3
OBJECT IDENTIFIER    

sysGuestVlan 1.3.6.1.4.1.207.1.4.167.64.4
OBJECT IDENTIFIER    

sysPnacSystemControl 1.3.6.1.4.1.207.1.4.167.64.1.1
Starts or shutdowns PNAC Module in the system. When set as 'start',resources required by PNAC module are allocated & PNAC module starts running. When shutdown, all resources used by PNAC module will be released to the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER start(1), shutdown(2)  

sysPnacAuthenticServer 1.3.6.1.4.1.207.1.4.167.64.1.3
This object is used to configure for the choice of local or remote Authentication Server to be used by the Authenticator for its authentication services.
Status: current Access: read-write
OBJECT-TYPE    
  AuthenticMethod  

sysPnacNasId 1.3.6.1.4.1.207.1.4.167.64.1.4
This object is the Network Access Server Identifier to be presented before the remote Authentication Server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

sysPnacPaePortTable 1.3.6.1.4.1.207.1.4.167.64.1.5
A table of system level information for each port supported by the EnterprisePNAC. An entry appears in this table for each port of this system. This table is an extension of dot1xPaePortTable of IEEE 802.1x MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabPnacPaePortEntry

sysPnacPaePortEntry 1.3.6.1.4.1.207.1.4.167.64.1.5.1
Configuration as port based or MAC based authentication and Supplicant count on a port. Index to this table is same as that of the dot1xPaePortTable, which is the InterfaceIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabPnacPaePortEntry  

sysPnacPaePortNumber 1.3.6.1.4.1.207.1.4.167.64.1.5.1.1
The port number associated with this port.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

sysPnacPaePortStatus 1.3.6.1.4.1.207.1.4.167.64.1.5.1.6
The value of the combined Port status.
Status: current Access: read-only
OBJECT-TYPE    
  PaeControlledPortStatus  

sysPnacPaeMultiAuthEnable 1.3.6.1.4.1.207.1.4.167.64.1.5.1.7
This object indicates dot1x multi hsot is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysPnacPaeProtocolMode 1.3.6.1.4.1.207.1.4.167.64.1.5.1.8
This object indicates mode is 802.1x or mac based.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysPnacPaePiggybackMode 1.3.6.1.4.1.207.1.4.167.64.1.5.1.9
This object indicates piggyback mode is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysPnacPaeVlanAssignment 1.3.6.1.4.1.207.1.4.167.64.1.5.1.10
This object indicates vlan assignment is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysPnacPaeSecureVlan 1.3.6.1.4.1.207.1.4.167.64.1.5.1.11
This object indicates Secure vlan is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysPnacModuleOperStatus 1.3.6.1.4.1.207.1.4.167.64.1.6
This read only objects gives actual status of the PNAC Module (Operational status of module). When Module is enabled PNAC protocol starts functioning. When the module is disabled all the dynamically allocated memory will be freed and PNAC protocol stops functioning.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysPnacASUserConfigTable 1.3.6.1.4.1.207.1.4.167.64.3.1
This table contains authentication related User configuration information maintained by PNAC local Authentication Server.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabPnacASUserConfigEntry

sysPnacASUserConfigEntry 1.3.6.1.4.1.207.1.4.167.64.3.1.1
Each entry contains User name, Password, Authentication protocol used, Authenticated session timeout and Access ports list of the User seeking authentication.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabPnacASUserConfigEntry  

sysPnacASUserConfigUserName 1.3.6.1.4.1.207.1.4.167.64.3.1.1.1
Identity of the User seeking authentication. A string of not more than 20 printable characters.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(0..115)  

sysPnacASUserConfigPassword 1.3.6.1.4.1.207.1.4.167.64.3.1.1.2
The secret Password of the User. A string of not more than 20 printable characters. When read, this always returns a String of length zero.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

sysPnacASUserConfigAuthProtocol 1.3.6.1.4.1.207.1.4.167.64.3.1.1.3
The Authentication protocol supported for the User.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sysPnacASUserConfigAuthTimeout 1.3.6.1.4.1.207.1.4.167.64.3.1.1.4
The time in seconds after which the Authentication offerred to the User ceases. Maximum value of the object can be 7200 seconds. When the object value is 0, the ReAuthPeriod of the Authenticator port is used by Authenticator.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

sysPnacASUserConfigPortList 1.3.6.1.4.1.207.1.4.167.64.3.1.1.5
The complete set of ports of Authenticator to which the User is allowed or denied access, on the basis of setting of 'sysPnacASUserConfigPermission' object.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

sysPnacASUserConfigPermission 1.3.6.1.4.1.207.1.4.167.64.3.1.1.6
For the set of ports indicated by 'sysPnacASUserConfigPortList' object, the User is allowed access when this object is set 'allow' and is denied access when this object is set 'deny'.
Status: current Access: read-write
OBJECT-TYPE    
  PermissionType  

sysPnacASUserConfigDynamicVlanID 1.3.6.1.4.1.207.1.4.167.64.3.1.1.7
Dynamic Vlan ID is assigned by Switch in local mode
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

sysPnacASUserConfigRowStatus 1.3.6.1.4.1.207.1.4.167.64.3.1.1.8
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysPnacGuestVlanTable 1.3.6.1.4.1.207.1.4.167.64.4.1
This table contains authentication session information associated with each Guest vlan while Authenticator operates in port based authentication mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabPnacGuestVlanEntry

sysPnacGuestVlanEntry 1.3.6.1.4.1.207.1.4.167.64.4.1.1
Guest Vlan ID assign with each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabPnacGuestVlanEntry  

sysPnacPaePortNo 1.3.6.1.4.1.207.1.4.167.64.4.1.1.1
The port number associated with this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

sysPnacGuestVlanId 1.3.6.1.4.1.207.1.4.167.64.4.1.1.2
specify the guest vlan tag.0 for non exiting
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSystemInfo 1.3.6.1.4.1.207.1.4.167.81.1
OBJECT IDENTIFIER    

sysConfigControl 1.3.6.1.4.1.207.1.4.167.81.2
OBJECT IDENTIFIER    

sysMirror 1.3.6.1.4.1.207.1.4.167.81.3
OBJECT IDENTIFIER    

sysIpAuthMgr 1.3.6.1.4.1.207.1.4.167.81.7
OBJECT IDENTIFIER    

sysLBDdetect 1.3.6.1.4.1.207.1.4.167.81.22
OBJECT IDENTIFIER    

sysSwitchName 1.3.6.1.4.1.207.1.4.167.81.1.1
System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) A!V + _ = .
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..15)  

sysHardwareVersion 1.3.6.1.4.1.207.1.4.167.81.1.2
Version number of the Hardware.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..15)  

sysFirmwareVersion 1.3.6.1.4.1.207.1.4.167.81.1.3
Version number of the Firmware.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..15)  

sysDefaultIpAddrCfgMode 1.3.6.1.4.1.207.1.4.167.81.1.4
Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER manual(1), dynamic(2)  

sysDefaultIpAddr 1.3.6.1.4.1.207.1.4.167.81.1.5
Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysDefaultIpSubnetMask 1.3.6.1.4.1.207.1.4.167.81.1.6
IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysRestart 1.3.6.1.4.1.207.1.4.167.81.1.9
This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sysConfigSaveOption 1.3.6.1.4.1.207.1.4.167.81.1.10
Specifies whether the configurations of the switch has to be saved or not. The value 'noSave' specifies that the configurations need not be saved. The value 'flashSave' specifies that the configurations need to be saved in flash in the specified file name sysConfigSaveFileName. The value 'remoteSave' specifies that the configurations need to be saved in specified remote system. The value 'startupConfig' specifies that the configurations need to be saved in flash in the 'Startup Configuration File'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noSave(1), flashSave(2), remoteSave(3), startupConfig(4)  

sysConfigSaveIpAddr 1.3.6.1.4.1.207.1.4.167.81.1.11
IP Address of the remote system to which the switch configurations have to be saved. This object is valid only if 'sysConfigSaveOption' is chosen to be 'remoteSave'.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysConfigSaveFileName 1.3.6.1.4.1.207.1.4.167.81.1.12
Name of the file in which the switch configurations are to be saved. This object is valid only if 'sysConfigSaveOption' is chosen to be 'flashSave' or 'remoteSave'.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..128)  

sysInitiateConfigSave 1.3.6.1.4.1.207.1.4.167.81.1.13
When set as 'true' switch configurations save operation is initiated. As soon as the configuration save operation is completed, the value of this object reverts back to 'false'. All the configurations made via the three interfaces viz. -> commandline interface -> Web Interface -> SNMP interface are saved either in 'Startup Configuration File' in the flash or in the specified 'sysConfigSaveFileName' in the flash or in the chosen remote system, dsysending upon 'ConfigSaveOption'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sysConfigSaveStatus 1.3.6.1.4.1.207.1.4.167.81.1.14
Status of configuration save operation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER saveInProgress(1), saveSuccessful(2), saveFailed(3), notInitiated(4)  

sysConfigRestoreOption 1.3.6.1.4.1.207.1.4.167.81.1.15
Specifies whether the switch configurations have to be restored or not. The value 'noRestore' specifies that the switch configurations need not be restored when the system is restarted. The value 'restore' specifies that the configurations need to be restored from the 'Startup Configuration File' in the flash when the system is restarted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noRestore(1), restore(2)  

sysRemoteConfigRestoreIpAddr 1.3.6.1.4.1.207.1.4.167.81.1.16
IP Address of the remote system from where the switch configurations have to be downloaded to the 'Startup Configuration File' in the flash.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysConfigRestoreFileName 1.3.6.1.4.1.207.1.4.167.81.1.17
The configuration file name in the remote system which has to be downloaded to the 'Startup Configuration File' and set this name to 'Startup Configuration Restire File Name' in the flash.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..128)  

sysInitiateRemoteConfigRestore 1.3.6.1.4.1.207.1.4.167.81.1.18
When set as 'true', the switch configurations will be downloaded from the specified remote system to the 'Startup Configuration File' in the flash. As soon as the configuration download operation is completed, the value of this object reverts back to 'false'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sysConfigRestoreStatus 1.3.6.1.4.1.207.1.4.167.81.1.19
The status of the switch configuration restore operation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER restoreInprogress(1), restoreSuccessful(2), restoreFailed(3), notInitiated(4)  

sysDlFirmwareFromIp 1.3.6.1.4.1.207.1.4.167.81.1.20
The Ip Address of machine from where the firmware has to be downloaded.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysDlFirmwareName 1.3.6.1.4.1.207.1.4.167.81.1.21
The firmware name which is to be downloaded to the switch.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..128)  

sysInitiateDlFirmware 1.3.6.1.4.1.207.1.4.167.81.1.22
Initiates the firmware Download operation.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sysLoggingOption 1.3.6.1.4.1.207.1.4.167.81.1.23
The option specifies whether the debug logging messages is to be sent to console or to a file(system buffer) in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER console(1), file(2)  

sysUploadLogFileToIp 1.3.6.1.4.1.207.1.4.167.81.1.24
The Ip address of TFTP server to which the log file is to be uploaded.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysLogFileName 1.3.6.1.4.1.207.1.4.167.81.1.25
The file name to be used for uploading the logs to the remote system.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..128)  

sysInitiateUlLogFile 1.3.6.1.4.1.207.1.4.167.81.1.26
Initiates uploading of log file to the specified IP address in 'sysUploadLogFileToIp'. The logs will be uploaded and saved in a file using the file name which was specified in 'sysLogFileName'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sysSysContact 1.3.6.1.4.1.207.1.4.167.81.1.29
The textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is known, the value is the zero-length string.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..50)  

sysSysLocation 1.3.6.1.4.1.207.1.4.167.81.1.30
The physical location of this node (e.g., `telsyshone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..50)  

sysLoginAuthentication 1.3.6.1.4.1.207.1.4.167.81.1.31
The mechanism by which the user login to access the GUI for configuration has to be authenticated. Authentication is done either locally or in the remote side through a RADIUS Server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER local(1), remoteRadius(2), remoteTacacs(3)  

sysSwitchBaseMacAddress 1.3.6.1.4.1.207.1.4.167.81.1.32
Ethernet address (base address) of the Switch. This base Mac Address, if modified, will take effect only when the Switch is restarted.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

sysSwitchDate 1.3.6.1.4.1.207.1.4.167.81.1.34
The date is display in the switch in the format, Hours:Minutes:Seconds Day Month Year e.g 19:10:31 11 08 2005 01-12 Month - beginning from January to December The railway time 00 to 24 hours can be displayed. The Display of the date is in the format , WeekDay Month Day Hours:Minutes:Seconds Year e.g 04 09 21 18:11:30 2005 01-07 WeekDay - beginning from Sunday to Saturday 01-12 Month - beginning from January to December
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(40)  

sysHttpPort 1.3.6.1.4.1.207.1.4.167.81.1.37
The port to be used by the hosts/PC to configure ISS using the Web Interface The HTTP server must be disabled before this configuration is done
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

sysHttpStatus 1.3.6.1.4.1.207.1.4.167.81.1.38
This object is for enabling or disabling HTTP in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysDefaultVlanId 1.3.6.1.4.1.207.1.4.167.81.1.41
The Default VLAN Identifier to be used at system startup. The VLAN Module creates this vlan as the default vlan. The Default VLAN Identifier, if modified, will take effect only when the switch is restarted
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..4094  

sysWebAutoTimeoutInterval 1.3.6.1.4.1.207.1.4.167.81.1.42
This time interval to be used at counting time seconds to logout web interface automatically.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 180..3600  

sysCliAutoTimeoutInterval 1.3.6.1.4.1.207.1.4.167.81.1.43
This time interval to be used at counting time seconds to logout command interface automatically.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..18000  

sysCpuPolicerStatus 1.3.6.1.4.1.207.1.4.167.81.1.44
This object is for enabling or disabling cpu policer in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysLedEcoModeStatus 1.3.6.1.4.1.207.1.4.167.81.1.45
This object is for enabling or disabling LED ECO mode in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysPowerSavingEnable 1.3.6.1.4.1.207.1.4.167.81.1.62
This object is for enabling or disabling powersaving in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysDhcpAutoConfiguration 1.3.6.1.4.1.207.1.4.167.81.1.63
This object is for enabling or disabling DHCP auto configuration in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysAsyVLANEnable 1.3.6.1.4.1.207.1.4.167.81.1.64
This object is for set asyvlan to ivl or svl in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

issCosEnable 1.3.6.1.4.1.207.1.4.167.81.1.65
This object is for enabling or disabling COS in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysTrapEnable 1.3.6.1.4.1.207.1.4.167.81.1.66
This object is for enabling or disabling Trap in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysFDResetStateEnable 1.3.6.1.4.1.207.1.4.167.81.1.67
Enable/Disable Factory Default Reset function. The Factory Default Reset function is used to enable or disable the push button and reset function on the device. When the user wants to disable reset function that must be configure a password to lock it. Once want to recovery the reset function, the password was needed to verify authorize.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysFDRInputPw 1.3.6.1.4.1.207.1.4.167.81.1.68
Input a password first and then the sysFDResetStateEnable can work correctly.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..12)  

sysConfigCtrlTable 1.3.6.1.4.1.207.1.4.167.81.2.1
A table to control device features like egress traffic control, stats collection, etc. either for the entire switch or for each interface in the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabConfigCtrlEntry

sysConfigCtrlEntry 1.3.6.1.4.1.207.1.4.167.81.2.1.1
An entry appears in this table for each interface in the system. In addition to that an entry with index '0' is created in this table by default. If 'sysConfigCtrlStatus' of the entry '0' is made 'valid', then global control is chosen and the values against entry '0' is applicable for all the interfaces of the switch. If 'sysConfigCtrlStatus' of the entry '0' is made 'invalid', then interface-wise control is chosen & the values against each interface index is applicable for that interface. At a particular point of time, either global control will be applicable or interface-wise control is applicable. Both will not be considered together. Index to the table is the interface index of the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabConfigCtrlEntry  

sysConfigCtrlIndex 1.3.6.1.4.1.207.1.4.167.81.2.1.1.1
Interface index of the port for which the configuration in this entry applies. If any configuration is made in this table for the index '0', that configuration will be considered as global configuration and is applicable for all the interfaces of the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

sysConfigCtrlEgressStatus 1.3.6.1.4.1.207.1.4.167.81.2.1.1.2
Controls the transmission of egress traffic over this interface. This value for entry '0' controls the egress traffic over all interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysConfigCtrlStatsCollection 1.3.6.1.4.1.207.1.4.167.81.2.1.1.3
Enables or disables statistics collection for this interface. This value for entry '0' controls the stats collection for all interfaces.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysConfigCtrlStatus 1.3.6.1.4.1.207.1.4.167.81.2.1.1.4
Speficies the validity of the entry. If the 'Config Control Status' for entry '0' is made 'valid', then global control is chosen in the system. It signifies that the values against entry '0' is applicable for all the interfaces of the switch. If the 'Config Control Status' for entry '0' is made 'invalid', then interface-wise control is chosen. Then the values against each interface index is applicable for that interface. By default, 'sysConfigCtrlStatus' will be 'invalid' for entry '0' and 'valid' for all other entries. (ie) by default, interface-wise configuration is enabled in the system. The status of entries other than the zeroth(0th) entry can not be made 'invalid'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

sysPortCtrlTable 1.3.6.1.4.1.207.1.4.167.81.2.2
A table to control the port specific parameters of the device like speed, duplex mode, etc.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabPortCtrlEntry

sysPortCtrlEntry 1.3.6.1.4.1.207.1.4.167.81.2.2.1
An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabPortCtrlEntry  

sysPortCtrlIndex 1.3.6.1.4.1.207.1.4.167.81.2.2.1.1
Interface index of the port for which the configuration in this entry applies.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

sysPortCtrlMode 1.3.6.1.4.1.207.1.4.167.81.2.2.1.2
Speficies the mode in which the speed, duplex modes and flow control of the interface is determined. If set as 'auto', the hardware senses speed and negotiates with the port on the other end of the link for data transfer operation as 'full-duplex' or 'half-duplex' and about flow contol. If set as 'nonegotiation', the configured values for interface speed, duplex mode and flow control will be effective.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), noNegotiation(2)  

sysPortCtrlDuplex 1.3.6.1.4.1.207.1.4.167.81.2.2.1.3
Configures interface data transfer mode as full-duplex or half-duplex. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negotiating with its peer
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER full(1), half(2)  

sysPortCtrlSpeed 1.3.6.1.4.1.207.1.4.167.81.2.2.1.4
Configures interface speed. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negotiating with its peer
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tenMBPS(1), hundredMBPS(2), oneGB(3), tenGB(4)  

sysPortCtrlFlowControl 1.3.6.1.4.1.207.1.4.167.81.2.2.1.5
Enables / disables flow control for the interface. This object be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negotiating with its peer
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysPortCtrlMDI 1.3.6.1.4.1.207.1.4.167.81.2.2.1.10
Sets the auto/mdi/mdix of the copper interface. Fiber media is not support.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), mdi(2), mdix(3)  

issJumboFramePerPortEnable 1.3.6.1.4.1.207.1.4.167.81.2.2.1.11
Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1522 bytes) of up to 10,000 bytes (tagged). Default jumbo frame is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

issJumboFramePerPortMtu 1.3.6.1.4.1.207.1.4.167.81.2.2.1.12
Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1522 bytes) of up to 10,000 bytes (tagged). Default jumbo frame MTU is 10000.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1522..10000  

sysPortCtrlEAPPassThrough 1.3.6.1.4.1.207.1.4.167.81.2.2.1.13
Enables / disables dot1x EAP packet pass through for the interface. This object be configured only if the dot1x is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysPortCtrlBPDUPassThrough 1.3.6.1.4.1.207.1.4.167.81.2.2.1.14
Enables / disables STP BPDU passthrough for the interface. This object be configured only if the RSTP/MSTP is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysMirrorStatus 1.3.6.1.4.1.207.1.4.167.81.3.1
Provides control over the mirroring feature in the switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysMirrorToPort 1.3.6.1.4.1.207.1.4.167.81.3.2
Specifies the port to which the mirrored traffic in the system is to be copied.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysMirrorCtrlTable 1.3.6.1.4.1.207.1.4.167.81.3.3
A table to control mirroring features either for the entire switch or for each interface in the switch. Parameters in this table are valid only when the 'sysMirrorStatus' for the switch is not 'disabled'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabMirrorCtrlEntry

sysMirrorCtrlEntry 1.3.6.1.4.1.207.1.4.167.81.3.3.1
An entry appears in this table for each interface in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabMirrorCtrlEntry  

sysMirrorCtrlIndex 1.3.6.1.4.1.207.1.4.167.81.3.3.1.1
The interface index of the port for which the configuration in this entry applies.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

sysMirrorCtrlIngressMirroring 1.3.6.1.4.1.207.1.4.167.81.3.3.1.2
Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysMirrorCtrlEgressMirroring 1.3.6.1.4.1.207.1.4.167.81.3.3.1.3
Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysMirrorCtrlStatus 1.3.6.1.4.1.207.1.4.167.81.3.3.1.4
Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysIpAuthMgrStatus 1.3.6.1.4.1.207.1.4.167.81.7.1
Provides control over the Ip authentication management feature in the switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysIpAuthMgrTable 1.3.6.1.4.1.207.1.4.167.81.7.2
A table to configure IP authorized managers in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabIpAuthMgrEntry

sysIpAuthMgrEntry 1.3.6.1.4.1.207.1.4.167.81.7.2.1
Each entry in this table rsysresents rules for particular IP authorized manager.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabIpAuthMgrEntry  

sysIpAuthMgrIpAddr 1.3.6.1.4.1.207.1.4.167.81.7.2.1.1
Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

sysIpAuthMgrIpMask 1.3.6.1.4.1.207.1.4.167.81.7.2.1.2
Specifies the IP address mask to be applied on sysIpAuthMgrIpAddr. Value 0.0.0.0 indicates mask for 'Any Manager'.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

sysIpAuthMgrPortList 1.3.6.1.4.1.207.1.4.167.81.7.2.1.3
Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

sysIpAuthMgrVlanList 1.3.6.1.4.1.207.1.4.167.81.7.2.1.4
Specifies the Vlan's in which the IP authorized manager can reside. By default the manager is allowed to reside in any vlan. If a set of vlans are configured in the 'VlanList', the manager can reside only in the configured vlan set. Access to the switch will be denied from any other vlan.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sysIpAuthMgrAllowedServices 1.3.6.1.4.1.207.1.4.167.81.7.2.1.6
Specifies the allowed services through which the authorized manager can access the switch. This object takes bit mask values. The services rsysresented by each bit position is as given below: With bit 0 being the Least Significant Bit, Bit0 --> snmp Bit1 --> telnet Bit2 --> http Bit3 --> https Bit4 --> ssh If the particular bit is set to 1,corresponding service is allowed for the configured manager. By default all services are allowed for the configured manager.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysIpAuthMgrRowStatus 1.3.6.1.4.1.207.1.4.167.81.7.2.1.7
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysLBDStateEnable 1.3.6.1.4.1.207.1.4.167.81.22.1
Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged switchs.The Switch will automatically shutdown the port and sends a log to the administrator.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysLBDInterval 1.3.6.1.4.1.207.1.4.167.81.22.2
Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP packet automatically.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..32767  

sysLBDRecoverTime 1.3.6.1.4.1.207.1.4.167.81.22.3
This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop Detection Recover Time. The default is 60 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0 | 60..1000000  

sysLBDCtrlTable 1.3.6.1.4.1.207.1.4.167.81.22.4
A table to control Loopback detection features either for the entire switch or for each interface in the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SysLBDCtrlEntry

sysLBDCtrlEntry 1.3.6.1.4.1.207.1.4.167.81.22.4.1
An entry appears in this table for each interface in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SysLBDCtrlEntry  

sysLBDCtrlIndex 1.3.6.1.4.1.207.1.4.167.81.22.4.1.1
The interface index of the port for which the configuration in this entry applies.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

sysLBDPortStatus 1.3.6.1.4.1.207.1.4.167.81.22.4.1.2
Provides control to per port enable or disable the loopback detection function. Default is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysLBDPortLoopStatus 1.3.6.1.4.1.207.1.4.167.81.22.4.1.3
The loop status for this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), disabled(2)  

sysRateControl 1.3.6.1.4.1.207.1.4.167.81.4
OBJECT IDENTIFIER    

sysStormControl 1.3.6.1.4.1.207.1.4.167.81.12
OBJECT IDENTIFIER    

sysRateCtrlTable 1.3.6.1.4.1.207.1.4.167.81.4.1
A table to control the rate limiting parameters either for the entire switch or for each interface in the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabRateCtrlEntry

sysRateCtrlEntry 1.3.6.1.4.1.207.1.4.167.81.4.1.1
An entry appears in this table for each physical interface in the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabRateCtrlEntry  

sysRateCtrlIndex 1.3.6.1.4.1.207.1.4.167.81.4.1.1.1
The interface index for which the configuration in this entry applies.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

sysRateCtrlEgressLimitValue 1.3.6.1.4.1.207.1.4.167.81.4.1.1.5
Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~100000(Kbits per second) in FE port, 64~1000000 (Kbits per second) in GE port. (Note: The multiple of 1850 Kbits/sec will be set automatically because the resolution of Giga-port Tx bandwidth control is 1850 Kbits/sec.)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1000000  

sysRateCtrlIngressLimitValue 1.3.6.1.4.1.207.1.4.167.81.4.1.1.7
Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~100000(Kbits per second) in FE port, 64~1000000(Kbits per second) in GE port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1000000  

sysStormCtrlTable 1.3.6.1.4.1.207.1.4.167.81.12.1
A table to control the rate limiting parameters either for the entire switch or for each interface in the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabStormCtrlEntry

sysStormCtrlEntry 1.3.6.1.4.1.207.1.4.167.81.12.1.1
An entry appears in this table for each physical interface in the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabStormCtrlEntry  

sysStormCtrlIndex 1.3.6.1.4.1.207.1.4.167.81.12.1.1.1
The interface index for which the configuration in this entry applies.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

sysDlfOnOff 1.3.6.1.4.1.207.1.4.167.81.12.1.1.2
This object indicates unknown unicast storm control function is enabled or disabled for device. When you enable unknown unicast storm control function, it will allowed you to limit the number of unknown unicast packets per second going through device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysBroadcastOnOff 1.3.6.1.4.1.207.1.4.167.81.12.1.1.3
This object indicates broadcast storm control function is enabled or disabled for device. When you enable broadcast storm control function, it will allowed you to limit the number of broadcast packets per second going through device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysMulticastOnOff 1.3.6.1.4.1.207.1.4.167.81.12.1.1.4
This object indicates multicast storm control function is enabled or disabled for device. When you enable multicast storm control function, it will allowed you to limit the number of multicast packets per second going through device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysStormCtrlThreshold 1.3.6.1.4.1.207.1.4.167.81.12.1.1.5
Allows to configure the limiting value for the maximum number of packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting on this interface. The value that can be set for this object is limited by the underlying hardware. The limit value must be low, medium, or high. (Notice : if the limit value is 0, it means unlimited.)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), low(1), medium(2), high(3)  

sysStormCtrlRowStatus 1.3.6.1.4.1.207.1.4.167.81.12.1.1.6
*This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysUserAuthMgr 1.3.6.1.4.1.207.1.4.167.81.30
OBJECT IDENTIFIER    

sysUserAuthMgrTable 1.3.6.1.4.1.207.1.4.167.81.30.1
A table to configure user authorized managers in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabUserAuthMgrEntry

sysUserAuthMgrEntry 1.3.6.1.4.1.207.1.4.167.81.30.1.1
User tabale entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabUserAuthMgrEntry  

sysUserAuthMgrId 1.3.6.1.4.1.207.1.4.167.81.30.1.1.1
User ID used for administration of this device.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

sysUserAuthMgrName 1.3.6.1.4.1.207.1.4.167.81.30.1.1.2
User Name used for administration of this device.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..20)  

sysUserAuthMgrRowStatus 1.3.6.1.4.1.207.1.4.167.81.30.1.1.3
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysDfsMIBObjects 1.3.6.1.4.1.207.1.4.167.83.1
OBJECT IDENTIFIER    

sysDfsMFClassifier 1.3.6.1.4.1.207.1.4.167.83.1.2
OBJECT IDENTIFIER    

sysDfsClassifier 1.3.6.1.4.1.207.1.4.167.83.1.3
OBJECT IDENTIFIER    

sysDfsInProfileAction 1.3.6.1.4.1.207.1.4.167.83.1.4
OBJECT IDENTIFIER    

sysDfsOutProfileAction 1.3.6.1.4.1.207.1.4.167.83.1.5
OBJECT IDENTIFIER    

sysDfsMeter 1.3.6.1.4.1.207.1.4.167.83.1.6
OBJECT IDENTIFIER    

sysDfsEnterpriseCoSqAlgorithm 1.3.6.1.4.1.207.1.4.167.83.1.8
OBJECT IDENTIFIER    

sysDfsMultiFieldClfrTable 1.3.6.1.4.1.207.1.4.167.83.1.2.1
This table contains the Multifield Classifier details. (In WEB, it means Class Map)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDscpMultiFieldClfrEntry

sysDfsMultiFieldClfrEntry 1.3.6.1.4.1.207.1.4.167.83.1.2.1.1
An IP Multi-field Classifier entry describes a single MF Classifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDscpMultiFieldClfrEntry  

sysDfsMultiFieldClfrId 1.3.6.1.4.1.207.1.4.167.83.1.2.1.1.1
An index that enumerates the MultiField Classifier filter.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

sysDfsMultiFieldClfrFilterId 1.3.6.1.4.1.207.1.4.167.83.1.2.1.1.2
This Object specifies the ID of the filter the details of which should be matched against the incoming packet
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

sysDfsMultiFieldClfrFilterType 1.3.6.1.4.1.207.1.4.167.83.1.2.1.1.3
This Object specifies the type of the filter
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER macfilter(1), ipfilter(2)  

sysDfsMultiFieldClfrStatus 1.3.6.1.4.1.207.1.4.167.83.1.2.1.1.4
The status of this concsystual row. All writable objects in this row may be modified only when the row status is not active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysDfsClfrTable 1.3.6.1.4.1.207.1.4.167.83.1.3.1
This table contains the Multifield filter details. (In WEB, it means Policy Map)
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDscpClfrEntry

sysDfsClfrEntry 1.3.6.1.4.1.207.1.4.167.83.1.3.1.1
An entry in the classifier table describes a single classifier. All classifier elements belonging to the same classifier use the classifier's sysDfsClfrId as part of their index.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDscpClfrEntry  

sysDfsClfrId 1.3.6.1.4.1.207.1.4.167.83.1.3.1.1.1
An index that enumerates the classifier entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

sysDfsClfrMFClfrId 1.3.6.1.4.1.207.1.4.167.83.1.3.1.1.2
The Object refers to a MultiField Classifier Id which is the index for the MF Classifier table. A Valid value of this object is not mandatory for the creation of an entry in this table. Need to map a Class ID (sysDfsMultiFieldClfrId)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysDfsClfrInProActionId 1.3.6.1.4.1.207.1.4.167.83.1.3.1.1.3
The Object refers to a In Profile Action Id which is the index for the InProfile Action Table. A Valid value of this object is not mandatory for the creation of an entry in this table. Must the same with sysDfsClfrId.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysDfsClfrOutProActionId 1.3.6.1.4.1.207.1.4.167.83.1.3.1.1.4
The Object refers to a Out Profile Action Id which is the index for the OutProfile Action Table. A Valid value of this object is not mandatory for the creation of an entry in this table. Must the same with sysDfsClfrId.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysDfsClfrStatus 1.3.6.1.4.1.207.1.4.167.83.1.3.1.1.5
The status of this concsystual row. The objects sysDfsClfrInProActionId and sysDfsClfrOutProActionId can be modified at any time. But the other Objects can not be modified when the RowStatus is 'active'for the particular entry. when the Row Status is set to 'destroy'for any of the entries only the entry is removed from the table. As the Object in this table are indexed to various other tables they stand unmodified by setting the RowStatus to 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysDfsInProfileActionTable 1.3.6.1.4.1.207.1.4.167.83.1.4.1
The Action Table enumerates actions that can be performed to a stream of traffic which is inprofile.For example, traffic exiting from a meter may be counted, marked, and potentially dropped before entering a queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDscpInProfileActionEntry

sysDfsInProfileActionEntry 1.3.6.1.4.1.207.1.4.167.83.1.4.1.1
Each entry in the action table allows description of one of action to be applied to traffic dsysending upon the treatment selected by sysDfsInProfileActionFlag.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDscpInProfileActionEntry  

sysDfsInProfileActionId 1.3.6.1.4.1.207.1.4.167.83.1.4.1.1.1
An index that enumerates the In Profile Action entries. Must be match the Policy ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

sysDfsInProfileActionFlag 1.3.6.1.4.1.207.1.4.167.83.1.4.1.1.2
This Object defines the action to be performed on the packet, when the packets are found to be In profile. Default Priority = 1 (0x0001), TOS = 4 (0x0004), DSCP = 1024 (0x0400)
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

sysDfsInProfileActionNewPrio 1.3.6.1.4.1.207.1.4.167.83.1.4.1.1.3
This Object kesyss the new priority value in case the action selected by sysDfsInProfileActionFlag is to assign a new priority/COS value.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

sysDfsInProfileActionDscp 1.3.6.1.4.1.207.1.4.167.83.1.4.1.1.6
This Object kesyss the new DSCP value in case the action selected by sysDfsInProfileActionFlag is to assign a new DSCP value.
Status: current Access: read-write
OBJECT-TYPE    
  DscpOrAny  

sysDfsInProfileActionStatus 1.3.6.1.4.1.207.1.4.167.83.1.4.1.1.7
The status of this concsystual row. All writable objects in this row may be modified only when the row status is not active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysDfsOutProfileActionTable 1.3.6.1.4.1.207.1.4.167.83.1.5.1
The Action Table enumerates actions that can be performed to a stream of traffic which is out of profile.For example, traffic exiting from a meter may be counted, marked, and potentially dropped before entering a queue.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDscpOutProfileActionEntry

sysDfsOutProfileActionEntry 1.3.6.1.4.1.207.1.4.167.83.1.5.1.1
Each entry in the action table allows description of one of action to be applied to traffic dsysending upon the treatment selected by sysDfsOutProfileActionFlag.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDscpOutProfileActionEntry  

sysDfsOutProfileActionId 1.3.6.1.4.1.207.1.4.167.83.1.5.1.1.1
An index that enumerates the Out Profile Action entries. Must the same with sysDfsClfrId.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

sysDfsOutProfileActionFlag 1.3.6.1.4.1.207.1.4.167.83.1.5.1.1.2
This Object defines the action to be performed on the packet when the packets are found to be out of profile. Drop = 2 (0x0002) DSCP = 4 (0x0004)
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

sysDfsOutProfileActionMID 1.3.6.1.4.1.207.1.4.167.83.1.5.1.1.4
This Object kesyss the Meter Id to be added to the DataPath to which this particular OutProfileAction is applicable. Must the same with sysDfsClfrId.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysDfsOutProfileActionStatus 1.3.6.1.4.1.207.1.4.167.83.1.5.1.1.5
The status of this concsystual row. All writable objects in this row may be modified only when the row status is not active. The row comprises of an Meter Id which is an index to the Meter Table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysDfsMeterTable 1.3.6.1.4.1.207.1.4.167.83.1.6.1
The Meter Table has the number of token with it and refreshCount value for associated with the meter.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDscpMeterEntry

sysDfsMeterEntry 1.3.6.1.4.1.207.1.4.167.83.1.6.1.1
An entry in the Meter Table describing a single instance of a Metering Unit.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDscpMeterEntry  

sysDfsMeterId 1.3.6.1.4.1.207.1.4.167.83.1.6.1.1.1
An index that enumerates the Meter entries. Must the same with sysDfsClfrId.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

sysDfsMeterRefreshCount 1.3.6.1.4.1.207.1.4.167.83.1.6.1.1.3
This values specifies the number of tokens to be added to the meter bucket after each 8 usec. (Threshold kbps)
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

sysDfsMeterStatus 1.3.6.1.4.1.207.1.4.167.83.1.6.1.1.4
The status of this concsystual row. All writable objects in this row may be modified only when this rowstatus in not active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysDfsCoSqAlgorithmTable 1.3.6.1.4.1.207.1.4.167.83.1.8.1
A table containing the scheduling algorithm applied to a particular port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDscpCoSqAlgorithmEntry

sysDfsCoSqAlgorithmEntry 1.3.6.1.4.1.207.1.4.167.83.1.8.1.1
An entry in this table gives mapping of a Port to user defined scheduled algorithm.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDscpCoSqAlgorithmEntry  

sysDfsPortId 1.3.6.1.4.1.207.1.4.167.83.1.8.1.1.1
Port identifier to which scheduling algorightm is set.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..24  

sysDfsCoSqAlgorithm 1.3.6.1.4.1.207.1.4.167.83.1.8.1.1.2
Sets the packet scheduling algorithm for the port The default is strictPriority(1).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER strictPriority(1), weightedRoundRobin(3)  

sysSyslogGeneralGroup 1.3.6.1.4.1.207.1.4.167.89.1
OBJECT IDENTIFIER    

sysSyslogLogs 1.3.6.1.4.1.207.1.4.167.89.2
OBJECT IDENTIFIER    

sysSyslogLogging 1.3.6.1.4.1.207.1.4.167.89.1.1
This object is for enabling or disabling syslog alert features in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysSyslogTimeStamp 1.3.6.1.4.1.207.1.4.167.89.1.2
This object is for enabling or disabling timestamp option. When enabled, the messages (log alert messages) will hold the time stamp information. When disabled, the time stamp information will not be carried with the messages sent to the log servers.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysSyslogSysBuffers 1.3.6.1.4.1.207.1.4.167.89.1.4
Number of log buffers to be allocated in the system
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..200  

sysSyslogClearLog 1.3.6.1.4.1.207.1.4.167.89.1.5
Clears the buffered logs. This object is set to 'false' by default. When set to 'True', the buffered logs will be cleared and the value of this object will become 'false' again.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sysSyslogConfigTable 1.3.6.1.4.1.207.1.4.167.89.1.6
A table for configuring module specific log levels.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSyslogConfigEntry

sysSyslogConfigEntry 1.3.6.1.4.1.207.1.4.167.89.1.6.1
An entry containing logging level options for a particular module.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSyslogConfigEntry  

sysSyslogConfigModule 1.3.6.1.4.1.207.1.4.167.89.1.6.1.1
Specifies the module for which the log level option has to be configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

sysSyslogConfigLogLevel 1.3.6.1.4.1.207.1.4.167.89.1.6.1.2
Specifies the log level option to be set for a specific module.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), info(6), debug(7)  

sysSyslogFacility 1.3.6.1.4.1.207.1.4.167.89.1.7
The Syslog standard facilities. The facility to be used when sending Syslog messages to this server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER local0(128), local1(136), local2(144), local3(152), local4(160), local5(168), local6(176), local7(184)  

sysSyslogLogSrvAddr 1.3.6.1.4.1.207.1.4.167.89.2.1
Specifies the syslog server IP to be used for remote logging. When configured, a new socket will be opened for this address. When the address is changed, the socket opened for the previous address will be closed and a new socket will be opened for this address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysPortSecurity 1.3.6.1.4.1.207.1.4.167.95.1
OBJECT IDENTIFIER    

sysPortSecurityTable 1.3.6.1.4.1.207.1.4.167.95.1.1
A list of port default priority Entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabPortSecEntry

sysPortSecurityEntry 1.3.6.1.4.1.207.1.4.167.95.1.1.1
A list of port default priority priorities.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabPortSecEntry  

sysPortSecurityIndex 1.3.6.1.4.1.207.1.4.167.95.1.1.1.1
The interface index for which the configuration in this entry applies.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

sysPortSecurityState 1.3.6.1.4.1.207.1.4.167.95.1.1.1.2
The security state on specific port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysPortSecurityMLA 1.3.6.1.4.1.207.1.4.167.95.1.1.1.3
The max. learning number of MAC entries on specific port
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSslGeneralGroup 1.3.6.1.4.1.207.1.4.167.96.1
OBJECT IDENTIFIER    

sysSslCiphers 1.3.6.1.4.1.207.1.4.167.96.2
OBJECT IDENTIFIER    

sysSslSecureHttpStatus 1.3.6.1.4.1.207.1.4.167.96.1.2
This object is for enabling or disabling secure HTTP in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysSslPort 1.3.6.1.4.1.207.1.4.167.96.1.3
This object is to configure the SSL port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sysSslTrace 1.3.6.1.4.1.207.1.4.167.96.1.4
Set the trace level for SSL. BIT 0 - Initialisation and Shutdown Trace. BIT 1 - Management trace. BIT 2 - Data path trace. BIT 3 - Control Plane trace. BIT 4 - Packet Dump. BIT 5 - OS Resource trace. BIT 6 - All Failure trace (All failures including Packet Validation) BIT 7 - Buffer Trace. Note:BIT 0 - Least significant bit BIT 7 - Most significant bit For example,setting the trace level to the value -0001 0101, will enable Init-Shutdown, data path and packet dump trace levels. Setting all the bits will enable all the trace levels and resetting them will disable all the trace levels.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSslCipherList 1.3.6.1.4.1.207.1.4.167.96.2.1
This object is to configure the cipher-suites list. This field is a bit mask, setting a bit indicates that the corresponding cipher-list will be involved in the server authentication. BIT 0 - RSA-NULL-MD5 BIT 1 - RSA-NULL-SHA1 BIT 2 - RSA-DES-SHA1 BIT 3 - RSA-3DES-SHA1 BIT 4 - DH-RSA-DES-SHA1 BIT 5 - DH-RSA-3DES-SHA1 BIT 6 - RSA-EXP1024-DES-SHA1 Note:BIT 0 - Least significant bit BIT 6 - Most significant bit For example,setting the cipher list to the value - 001 0101, will include RSA-NULL-MD5, RSA-DES-SHA1 and DH-RSA-DES-SHA1 as cipher-list for authentication.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSslDefaultCipherList 1.3.6.1.4.1.207.1.4.167.96.2.2
This object is to set the default cipher-suites list in 'sysSslCipherList'. Setting DefaultCipherList to TRUE would set the following cipher-list for authentication: - RSA_3DES_SHA1 - RSA_DES_SHA1 - RSA_EXP1024_DES_SHA1 The value of this object reverts back to FALSE once the default cipher list is set.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sysSshGeneralGroup 1.3.6.1.4.1.207.1.4.167.97.1
OBJECT IDENTIFIER    

sysSshVersionCompatibility 1.3.6.1.4.1.207.1.4.167.97.1.1
This object is to configure the SSH version compatibility mode. When set to TRUE, both SSH version-1 and SSH Version-2 will be supported. When set to FALSE, SSH version-2 only will be supported. By default SSH version-2 is supported.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sysSshCipherList 1.3.6.1.4.1.207.1.4.167.97.1.2
This object is to configure the cipher-suites list. This object takes values as bit mask. Setting a bit indicates that the corresponding cipher-list will be used for Encryption. The value of each bit position is as given below with bit 0 being the least significant bit: BIT 1 - DES-CBC BIT 0 - 3DES-CBC
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3  

sysSshMacList 1.3.6.1.4.1.207.1.4.167.97.1.3
This object is to configure the MAC-list. This object takes values as bit mask. Setting a bit indicates that the corresponding MAC-list will be used for authentication. The value of each bit position is as given below with bit 0 being the least significant bit: BIT 1 - HMAC-MD5 BIT 0 - HMAC-SHA1
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3  

sysSshTrace 1.3.6.1.4.1.207.1.4.167.97.1.4
Set the trace level for SSH. BIT 0 - Initialisation and Shutdown Trace. BIT 1 - Management trace. BIT 2 - Data path trace. BIT 3 - Control Plane trace. BIT 4 - Packet Dump. BIT 5 - OS Resource trace. BIT 6 - All Failure trace (All failures including Packet Validation) BIT 7 - Buffer Trace. Note:BIT 0 - Least significant bit BIT 7 - Most significant bit For example,setting the trace level to the value -0001 0101, will enable Init-Shutdown, data path and packet dump trace levels. Setting all the bits will enable all the trace levels and resetting them will disable all the trace levels.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSshStatus 1.3.6.1.4.1.207.1.4.167.97.1.5
This object is for enabling or disabling ssh in the system.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

sysSntpGeneralGroup 1.3.6.1.4.1.207.1.4.167.99.1
OBJECT IDENTIFIER    

sysSntpTzGroup 1.3.6.1.4.1.207.1.4.167.99.2
OBJECT IDENTIFIER    

sysSntpStatus 1.3.6.1.4.1.207.1.4.167.99.1.1
This object is for enabling or disabling SNTP Client feature in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysSntpPollInterval 1.3.6.1.4.1.207.1.4.167.99.1.2
The SNTP server polling interval in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTimeSeconds 1.3.6.1.4.1.207.1.4.167.99.1.3
This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 1970).
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpPrimarySrvAddr 1.3.6.1.4.1.207.1.4.167.99.1.4
Specifies the primary SNTP server IP to be used for network time syncronization. When configured, a new socket will be opened for this address. When the address is changed, the socket opened for the previous address will be closed and a new socket will be opened for this address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysSntpSecondSrvAddr 1.3.6.1.4.1.207.1.4.167.99.1.5
Specifies the secondary SNTP server IP to be used for network time syncronization. If the primary SNTP server fail, the system will try secondary SNTP server. When configured, a new socket will be opened for this address. When the address is changed, the socket opened for the previous address will be closed and a new socket will be opened for this address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysSntpTimeZoneMappingIndex 1.3.6.1.4.1.207.1.4.167.99.1.6
This object is used for distinguishing areas in the same time zone.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTzDSTStatus 1.3.6.1.4.1.207.1.4.167.99.2.1
This object is for enabling or disabling Time Zone Daylight Saving Time feature in the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysSntpTzMinutesWest 1.3.6.1.4.1.207.1.4.167.99.2.2
Specifies the Time Zone Offset from GMT in +/- Minutes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTzDSTStartMon 1.3.6.1.4.1.207.1.4.167.99.2.3
The start month of Daylight Saving Time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTzDSTStartDay 1.3.6.1.4.1.207.1.4.167.99.2.4
The start day of Daylight Saving Time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTzDSTStartHour 1.3.6.1.4.1.207.1.4.167.99.2.5
The start hour of Daylight Saving Time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTzDSTStartMinute 1.3.6.1.4.1.207.1.4.167.99.2.6
The start minutes of Daylight Saving Time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTzDSTEndMon 1.3.6.1.4.1.207.1.4.167.99.2.7
The end month of Daylight Saving Time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTzDSTEndDay 1.3.6.1.4.1.207.1.4.167.99.2.8
The end day of Daylight Saving Time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTzDSTEndHour 1.3.6.1.4.1.207.1.4.167.99.2.9
The end hour of Daylight Saving Time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTzDSTEndMinute 1.3.6.1.4.1.207.1.4.167.99.2.10
The end minutes of Daylight Saving Time.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sysSntpTzDSTForwardOffset 1.3.6.1.4.1.207.1.4.167.99.2.11
The adjusted time of Daylight Saving Time.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER halfHour(30), oneHour(60)  

sysDscpMIBObjects 1.3.6.1.4.1.207.1.4.167.100.1
OBJECT IDENTIFIER    

sysDscpTypeGroup 1.3.6.1.4.1.207.1.4.167.100.1.2
OBJECT IDENTIFIER    

sysDscpEnable 1.3.6.1.4.1.207.1.4.167.100.1.1
Enable / Disable DiffServ function
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysDscpType01 1.3.6.1.4.1.207.1.4.167.100.1.2.1
DiffServ Type 01 : IP ToS value = 0
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType02 1.3.6.1.4.1.207.1.4.167.100.1.2.2
DiffServ Type 02 : IP ToS value = 4
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType03 1.3.6.1.4.1.207.1.4.167.100.1.2.3
DiffServ Type 03 : IP ToS value = 8
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType04 1.3.6.1.4.1.207.1.4.167.100.1.2.4
DiffServ Type 04 : IP ToS value = 12
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType05 1.3.6.1.4.1.207.1.4.167.100.1.2.5
DiffServ Type 05 : IP ToS value = 16
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType06 1.3.6.1.4.1.207.1.4.167.100.1.2.6
DiffServ Type 06 : IP ToS value = 20
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType07 1.3.6.1.4.1.207.1.4.167.100.1.2.7
DiffServ Type 07 : IP ToS value = 24
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType08 1.3.6.1.4.1.207.1.4.167.100.1.2.8
DiffServ Type 08 : IP ToS value = 28
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType09 1.3.6.1.4.1.207.1.4.167.100.1.2.9
DiffServ Type 09 : IP ToS value = 32
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType10 1.3.6.1.4.1.207.1.4.167.100.1.2.10
DiffServ Type 10 : IP ToS value = 36
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType11 1.3.6.1.4.1.207.1.4.167.100.1.2.11
DiffServ Type 11 : IP ToS value = 40
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType12 1.3.6.1.4.1.207.1.4.167.100.1.2.12
DiffServ Type 12 : IP ToS value = 44
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType13 1.3.6.1.4.1.207.1.4.167.100.1.2.13
DiffServ Type 13 : IP ToS value = 48
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType14 1.3.6.1.4.1.207.1.4.167.100.1.2.14
DiffServ Type 14 : IP ToS value = 52
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType15 1.3.6.1.4.1.207.1.4.167.100.1.2.15
DiffServ Type 15 : IP ToS value = 56
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType16 1.3.6.1.4.1.207.1.4.167.100.1.2.16
DiffServ Type 16 : IP ToS value = 60
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType17 1.3.6.1.4.1.207.1.4.167.100.1.2.17
DiffServ Type 17 : IP ToS value = 64
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType18 1.3.6.1.4.1.207.1.4.167.100.1.2.18
DiffServ Type 18 : IP ToS value = 68
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType19 1.3.6.1.4.1.207.1.4.167.100.1.2.19
DiffServ Type 19 : IP ToS value = 72
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType20 1.3.6.1.4.1.207.1.4.167.100.1.2.20
DiffServ Type 20 : IP ToS value = 76
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType21 1.3.6.1.4.1.207.1.4.167.100.1.2.21
DiffServ Type 21 : IP ToS value = 80
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType22 1.3.6.1.4.1.207.1.4.167.100.1.2.22
DiffServ Type 22 : IP ToS value = 84
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType23 1.3.6.1.4.1.207.1.4.167.100.1.2.23
DiffServ Type 23 : IP ToS value = 88
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType24 1.3.6.1.4.1.207.1.4.167.100.1.2.24
DiffServ Type 24 : IP ToS value = 92
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType25 1.3.6.1.4.1.207.1.4.167.100.1.2.25
DiffServ Type 25 : IP ToS value = 96
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType26 1.3.6.1.4.1.207.1.4.167.100.1.2.26
DiffServ Type 26 : IP ToS value = 100
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType27 1.3.6.1.4.1.207.1.4.167.100.1.2.27
DiffServ Type 27 : IP ToS value = 104
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType28 1.3.6.1.4.1.207.1.4.167.100.1.2.28
DiffServ Type 28 : IP ToS value = 108
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType29 1.3.6.1.4.1.207.1.4.167.100.1.2.29
DiffServ Type 29 : IP ToS value = 112
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType30 1.3.6.1.4.1.207.1.4.167.100.1.2.30
DiffServ Type 30 : IP ToS value = 116
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType31 1.3.6.1.4.1.207.1.4.167.100.1.2.31
DiffServ Type 31 : IP ToS value = 120
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType32 1.3.6.1.4.1.207.1.4.167.100.1.2.32
DiffServ Type 32 : IP ToS value = 124
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType33 1.3.6.1.4.1.207.1.4.167.100.1.2.33
DiffServ Type 33 : IP ToS value = 128
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType34 1.3.6.1.4.1.207.1.4.167.100.1.2.34
DiffServ Type 34 : IP ToS value = 132
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType35 1.3.6.1.4.1.207.1.4.167.100.1.2.35
DiffServ Type 35 : IP ToS value = 136
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType36 1.3.6.1.4.1.207.1.4.167.100.1.2.36
DiffServ Type 36 : IP ToS value = 140
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType37 1.3.6.1.4.1.207.1.4.167.100.1.2.37
DiffServ Type 37 : IP ToS value = 144
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType38 1.3.6.1.4.1.207.1.4.167.100.1.2.38
DiffServ Type 38 : IP ToS value = 148
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType39 1.3.6.1.4.1.207.1.4.167.100.1.2.39
DiffServ Type 39 : IP ToS value = 152
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType40 1.3.6.1.4.1.207.1.4.167.100.1.2.40
DiffServ Type 40 : IP ToS value = 156
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType41 1.3.6.1.4.1.207.1.4.167.100.1.2.41
DiffServ Type 41 : IP ToS value = 160
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType42 1.3.6.1.4.1.207.1.4.167.100.1.2.42
DiffServ Type 42 : IP ToS value = 164
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType43 1.3.6.1.4.1.207.1.4.167.100.1.2.43
DiffServ Type 43 : IP ToS value = 168
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType44 1.3.6.1.4.1.207.1.4.167.100.1.2.44
DiffServ Type 44 : IP ToS value = 172
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType45 1.3.6.1.4.1.207.1.4.167.100.1.2.45
DiffServ Type 45 : IP ToS value = 176
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType46 1.3.6.1.4.1.207.1.4.167.100.1.2.46
DiffServ Type 46 : IP ToS value = 180
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType47 1.3.6.1.4.1.207.1.4.167.100.1.2.47
DiffServ Type 47 : IP ToS value = 184
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType48 1.3.6.1.4.1.207.1.4.167.100.1.2.48
DiffServ Type 48 : IP ToS value = 188
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType49 1.3.6.1.4.1.207.1.4.167.100.1.2.49
DiffServ Type 49 : IP ToS value = 192
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType50 1.3.6.1.4.1.207.1.4.167.100.1.2.50
DiffServ Type 50 : IP ToS value = 196
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType51 1.3.6.1.4.1.207.1.4.167.100.1.2.51
DiffServ Type 51 : IP ToS value = 200
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType52 1.3.6.1.4.1.207.1.4.167.100.1.2.52
DiffServ Type 52 : IP ToS value = 204
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType53 1.3.6.1.4.1.207.1.4.167.100.1.2.53
DiffServ Type 53 : IP ToS value = 208
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType54 1.3.6.1.4.1.207.1.4.167.100.1.2.54
DiffServ Type 54 : IP ToS value = 212
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType55 1.3.6.1.4.1.207.1.4.167.100.1.2.55
DiffServ Type 55 : IP ToS value = 216
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType56 1.3.6.1.4.1.207.1.4.167.100.1.2.56
DiffServ Type 56 : IP ToS value = 220
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType57 1.3.6.1.4.1.207.1.4.167.100.1.2.57
DiffServ Type 57 : IP ToS value = 224
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType58 1.3.6.1.4.1.207.1.4.167.100.1.2.58
DiffServ Type 58 : IP ToS value = 228
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType59 1.3.6.1.4.1.207.1.4.167.100.1.2.59
DiffServ Type 59 : IP ToS value = 232
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType60 1.3.6.1.4.1.207.1.4.167.100.1.2.60
DiffServ Type 60 : IP ToS value = 236
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType61 1.3.6.1.4.1.207.1.4.167.100.1.2.61
DiffServ Type 61 : IP ToS value = 240
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType62 1.3.6.1.4.1.207.1.4.167.100.1.2.62
DiffServ Type 62 : IP ToS value = 244
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType63 1.3.6.1.4.1.207.1.4.167.100.1.2.63
DiffServ Type 63 : IP ToS value = 248
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysDscpType64 1.3.6.1.4.1.207.1.4.167.100.1.2.64
DiffServ Type 64 : IP ToS value = 252
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER class0(0), class1(1), class2(2), class3(3)  

sysSnoopInst 1.3.6.1.4.1.207.1.4.167.105.2
OBJECT IDENTIFIER    

sysSnoopVlan 1.3.6.1.4.1.207.1.4.167.105.3
OBJECT IDENTIFIER    

sysSnoopStats 1.3.6.1.4.1.207.1.4.167.105.4
OBJECT IDENTIFIER    

sysSnoopInstanceGlobalTable 1.3.6.1.4.1.207.1.4.167.105.2.1
This table contains multicast forwarding mode configuration for each instance running in the snooping switch
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnoopInstanceGlobalEntry

sysSnoopInstanceGlobalEntry 1.3.6.1.4.1.207.1.4.167.105.2.1.1
This table contains instance number and the multicast forwarding mode configuration for the particular instance
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnoopInstanceGlobalEntry  

sysSnoopInstanceGlobalInstId 1.3.6.1.4.1.207.1.4.167.105.2.1.1.1
Instance ID pertaining to the global configuration entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

sysSnoopInstanceGlobalSystemControl 1.3.6.1.4.1.207.1.4.167.105.2.1.1.3
Snooping module is shutdown or started through this object. When set to 'start', resources required by the Enterprise SNOOP module is allocated and the module starts running. When set to 'shutdown', all the resources are released back to the system and the module stops running.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER start(1), shutdown(2)  

sysSnoopInstanceConfigTable 1.3.6.1.4.1.207.1.4.167.105.2.2
This table contains global configuration of snooping for each instance running in switch
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnoopInstanceConfigEntry

sysSnoopInstanceConfigEntry 1.3.6.1.4.1.207.1.4.167.105.2.2.1
This table contains instance number, address type and the list of global configuration for the particular instance and address type
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnoopInstanceConfigEntry  

sysSnoopInstanceConfigInstId 1.3.6.1.4.1.207.1.4.167.105.2.2.1.1
Instance ID pertaining to the global configuration entry. Currently only one instance is supported so it is always 1
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

sysSnoopInetAddressType 1.3.6.1.4.1.207.1.4.167.105.2.2.1.2
Inet Address Type corresponding to the global configuration entry. This indicates whether the row is for IGMP/MLD Snooping
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

sysSnoopStatus 1.3.6.1.4.1.207.1.4.167.105.2.2.1.3
Enables or disables IGMP/MLD snooping in the system. When set to 'enabled', the Enterprise IGS/MLDS module starts protocol operations. When set to 'disabled', the IGS/MLDS module stops performing protocol operations.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysSnoopRouterPortPurgeInterval 1.3.6.1.4.1.207.1.4.167.105.2.2.1.5
This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..600  

sysSnoopPortPurgeInterval 1.3.6.1.4.1.207.1.4.167.105.2.2.1.6
This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which rsysort has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a rsysort message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 130..1225  

sysSnoopReportForwardInterval 1.3.6.1.4.1.207.1.4.167.105.2.2.1.7
This timer is used when proxy-reporting is disabled,the switch then has to suppress multiple IGMPv2/ MLDv1 report messages for the same group from being forwarded to the router. This is the interval (in seconds) within which report messages for the same multicast group will not be forwarded. The 'ReportForwardTimer' is per multicast group. This timer is started as soon as a report message for that group is forwarded out. Within this 'ReportForwardInterval' if another report for the same group arrives, that report will not be forwarded.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..25  

sysSnoopRetryCount 1.3.6.1.4.1.207.1.4.167.105.2.2.1.8
When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'sysSnoopRetryCount', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..5  

sysSnoopGrpQueryInterval 1.3.6.1.4.1.207.1.4.167.105.2.2.1.9
The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there are any intersted receivers. The switch will send 'sysSnoopRetryCount' queries before removing the port from the group membership information in the forwarding database.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..5  

sysSnoopReportFwdOnAllPorts 1.3.6.1.4.1.207.1.4.167.105.2.2.1.10
Snooping module will forward reports only on router ports by default, to enable forwarding on all other ports this object to provide a administrative control to forward the reports on all the member ports of the VLAN
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allports(1), rtrports(2)  

sysSnoopOperStatus 1.3.6.1.4.1.207.1.4.167.105.2.2.1.12
The operational status of the IGS/MLDS protocol. The value enabled(1) indicates the IGS/MLDS module is currently enabled in the system. The value disable(1) indicates the IGS/MLDS module is currently disabled in the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysSnoopSendQueryOnTopoChange 1.3.6.1.4.1.207.1.4.167.105.2.2.1.13
The Snooping Switch can be configured to send IGMP/MLD General queries on all non router ports when spanning tree topology change occurs in a network. If the spanning tree mode is RSTP, IGMP/MLD general queries will be sent on all the non router ports present in the switch.If the spanning tree mode is MSTP, IGMP/MLD general queries will be sent on all the non router ports of the VLAN mapped for the MSTP instance.When this object is set to 'enabled' ,the switch will generate general query messages
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysSnoopQuerierQueryInterval 1.3.6.1.4.1.207.1.4.167.105.2.2.1.16
This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier. A switch should be configured as a querier for a VLAN only when there are no queriers in the network.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..600  

sysSnoopVlanMcastMacFwdTable 1.3.6.1.4.1.207.1.4.167.105.3.1
This table contains MAC based multicast forwarding information. This information is applicable only if the 'sysSnoopMcastForwardingMode' is set to 'macbased'
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnoopVlanMcastMacFwdEntry

sysSnoopVlanMcastMacFwdEntry 1.3.6.1.4.1.207.1.4.167.105.3.1.1
This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnoopVlanMcastMacFwdEntry  

sysSnoopVlanMcastMacFwdInstId 1.3.6.1.4.1.207.1.4.167.105.3.1.1.1
Instance ID pertaining to the Multicast forwarding entry. Currently only one instance is supported so it is always 1
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

sysSnoopVlanMcastMacFwdVlanId 1.3.6.1.4.1.207.1.4.167.105.3.1.1.2
VLAN ID pertaining to the Multicast forwarding entry
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4094  

sysSnoopVlanMcastMacFwdInetAddressType 1.3.6.1.4.1.207.1.4.167.105.3.1.1.3
InetAddressType pertaining to the Multicast forwarding entry
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

sysSnoopVlanMcastMacFwdGroupAddress 1.3.6.1.4.1.207.1.4.167.105.3.1.1.4
Multicast group MAC address.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

sysSnoopVlanMcastMacFwdPortList 1.3.6.1.4.1.207.1.4.167.105.3.1.1.5
List of ports onto which the multicast data packets destined for this group will be forwarded.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

sysSnoopVlanRouterTable 1.3.6.1.4.1.207.1.4.167.105.3.3
This table contains the list of ports through which a router, in a particular VLAN is reachable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnoopVlanRouterEntry

sysSnoopVlanRouterEntry 1.3.6.1.4.1.207.1.4.167.105.3.3.1
Contains the VLAN ID and list of ports on which routers are present in the VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnoopVlanRouterEntry  

sysSnoopVlanRouterInstId 1.3.6.1.4.1.207.1.4.167.105.3.3.1.1
Instance ID pertaining to the router port entry. Currently only one instance is supported so it is always 1
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

sysSnoopVlanRouterVlanId 1.3.6.1.4.1.207.1.4.167.105.3.3.1.2
VLAN ID of the ports through which router is reachable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4094  

sysSnoopVlanRouterInetAddressType 1.3.6.1.4.1.207.1.4.167.105.3.3.1.3
It indicates whether the row belongs to IGMP / MLD snooping.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

sysSnoopVlanRouterPortList 1.3.6.1.4.1.207.1.4.167.105.3.3.1.4
List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

sysSnoopVlanFilterTable 1.3.6.1.4.1.207.1.4.167.105.3.4
This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnoopVlanFilterEntry

sysSnoopVlanFilterEntry 1.3.6.1.4.1.207.1.4.167.105.3.4.1
Contains snooping status , version and fast leave configuration for a specific VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnoopVlanFilterEntry  

sysSnoopVlanFilterInstId 1.3.6.1.4.1.207.1.4.167.105.3.4.1.1
Instance ID pertaining to VLAN filter table entry. Currently only one instance is supported so it is always 1
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

sysSnoopVlanFilterVlanId 1.3.6.1.4.1.207.1.4.167.105.3.4.1.2
VLAN ID for which snooping configuration is to be done.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4094  

sysSnoopVlanFilterInetAddressType 1.3.6.1.4.1.207.1.4.167.105.3.4.1.3
Indicates whether the row belongs to IGS/MLD snooping
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

sysSnoopVlanSnoopStatus 1.3.6.1.4.1.207.1.4.167.105.3.4.1.4
Enables or disables IGS/MLDS on that specific VLAN
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysSnoopVlanOperatingVersion 1.3.6.1.4.1.207.1.4.167.105.3.4.1.5
Indicates the operating version of the IGS/MLDS switch for a specific VLAN. The default operating mode on a specific VLAN is IGMP version 2 i.e, V2(2) or MLD version 1 i.e, V1(1)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER v1(1), v2(2)  

sysSnoopVlanFastLeave 1.3.6.1.4.1.207.1.4.167.105.3.4.1.7
Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysSnoopVlanQuerier 1.3.6.1.4.1.207.1.4.167.105.3.4.1.8
Indicates whether the switch is configured as a querier in the VLAN
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysSnoopVlanCfgQuerier 1.3.6.1.4.1.207.1.4.167.105.3.4.1.9
The snooping switch can be configured to send IGMP/MLD queries when IGMP/MLD routers are not present in the VLAN. When set to 'enabled' the switch will generate general query messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysSnoopVlanQueryInterval 1.3.6.1.4.1.207.1.4.167.105.3.4.1.10
This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there are no queriers in the network.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 60..600  

sysSnoopVlanRtrPortList 1.3.6.1.4.1.207.1.4.167.105.3.4.1.11
List of ports which are configured statically as router ports
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

sysSnoopVlanRowStatus 1.3.6.1.4.1.207.1.4.167.105.3.4.1.12
The status of a row in the VLAN filter table. By 'sysSnoopVlanRowStatus' new entries can be created in the VLAN filter table and the existing entries can be removed from the VLAN filter table
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sysSnoopStatsTable 1.3.6.1.4.1.207.1.4.167.105.4.1
This table contains snooping statistics maintained by the switch. The statistics are maintained on a per VLAN basis.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabSnoopStatsEntry

sysSnoopStatsEntry 1.3.6.1.4.1.207.1.4.167.105.4.1.1
Contains snooping statistics for a particular VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabSnoopStatsEntry  

sysSnoopStatsInstId 1.3.6.1.4.1.207.1.4.167.105.4.1.1.1
Instance ID pertaining for the statistics entry. Currently only one instance is supported so it is always 1
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

sysSnoopStatsVlanId 1.3.6.1.4.1.207.1.4.167.105.4.1.1.2
VLAN ID for which snooping statistics are displayed
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4094  

sysSnoopStatsInetAddressType 1.3.6.1.4.1.207.1.4.167.105.4.1.1.3
Indicates whether the statistics are for IGS/MLDS
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

sysSnoopStatsRxGenQueries 1.3.6.1.4.1.207.1.4.167.105.4.1.1.4
Provides the statistics of General Queries received by the snooping switch.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sysSnoopStatsRxGrpQueries 1.3.6.1.4.1.207.1.4.167.105.4.1.1.5
Provides the statistics of Group Specific Queries received by the snooping switch.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sysSnoopStatsRxAsmReports 1.3.6.1.4.1.207.1.4.167.105.4.1.1.7
Provides the statistics of IGMPv1/IGMPv2 Membership reports received by the snooping switch. In case of MLDS, it provides the statistics of MLDv1 membership reports.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sysSnoopStatsRxAsmLeaves 1.3.6.1.4.1.207.1.4.167.105.4.1.1.15
Provides the statistics of IGMPv2/MLDv1 Leave messages received by the snooping switch.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sysSnoopStatsTxGenQueries 1.3.6.1.4.1.207.1.4.167.105.4.1.1.16
Provides the statistics of General Queries transmitted by the snooping switch when it is act as a querier.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sysSnoopStatsTxGrpQueries 1.3.6.1.4.1.207.1.4.167.105.4.1.1.17
Provides the statistics of Group Specific Queries transmitted by the snooping switch.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sysSnoopStatsTxAsmReports 1.3.6.1.4.1.207.1.4.167.105.4.1.1.18
Provides the statistics of IGMPv1/IGMPv2 Membership reports transmitted by the snooping switch.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sysSnoopStatsTxAsmLeaves 1.3.6.1.4.1.207.1.4.167.105.4.1.1.20
Provides the statistics of IGMPv2/MLDv1 Leave messages transmitted by the snooping switch.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sysSnoopStatsDroppedPkts 1.3.6.1.4.1.207.1.4.167.105.4.1.1.21
Provides the number of erroneous IGMP/MLD packets dropped by the snooping switch due to failure in checksum calculation.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dNotifications 1.3.6.1.4.1.207.1.4.167.116.0
OBJECT IDENTIFIER    

dot1dBase 1.3.6.1.4.1.207.1.4.167.116.1
OBJECT IDENTIFIER    

l2Dot1dStp 1.3.6.1.4.1.207.1.4.167.116.2
OBJECT IDENTIFIER    

dot1dSr 1.3.6.1.4.1.207.1.4.167.116.3
OBJECT IDENTIFIER    

dot1dTp 1.3.6.1.4.1.207.1.4.167.116.4
OBJECT IDENTIFIER    

dot1dStatic 1.3.6.1.4.1.207.1.4.167.116.5
OBJECT IDENTIFIER    

dot1dBaseTable 1.3.6.1.4.1.207.1.4.167.116.1.1
List of per Virtual Bridge Module Parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dBaseEntry

dot1dBaseEntry 1.3.6.1.4.1.207.1.4.167.116.1.1.1
Virtual Bridge Rst Module Parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dBaseEntry  

dot1dBaseContextId 1.3.6.1.4.1.207.1.4.167.116.1.1.1.1
Virtual Bridge number
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

dot1dBaseBridgeAddress 1.3.6.1.4.1.207.1.4.167.116.1.1.1.2
The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1dStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

dot1dBaseNumPorts 1.3.6.1.4.1.207.1.4.167.116.1.1.1.3
The number of ports controlled by this bridging entity.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1dBaseType 1.3.6.1.4.1.207.1.4.167.116.1.1.1.4
Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), transparentonly(2), sourcerouteonly(3), srt(4)  

dot1dBasePortTable 1.3.6.1.4.1.207.1.4.167.116.1.2
A table that contains generic information about every port that is associated with this bridge. Transparent, source-route, and srt ports are included.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dBasePortEntry

dot1dBasePortEntry 1.3.6.1.4.1.207.1.4.167.116.1.2.1
A list of information for each port of the bridge.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dBasePortEntry  

dot1dBasePort 1.3.6.1.4.1.207.1.4.167.116.1.2.1.1
The port number of the port for which this entry contains bridge management information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

dot1dBasePortIfIndex 1.3.6.1.4.1.207.1.4.167.116.1.2.1.2
The value of the instance of the ifIndex object, defined in MIB-II, for the interface corresponding to this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1dBasePortCircuit 1.3.6.1.4.1.207.1.4.167.116.1.2.1.3
For a port which (potentially) has the same value of dot1dBasePortIfIndex as another port on the same bridge, this object contains the name of an object instance unique to this port. For example, in the case where multiple ports correspond one- to-one with multiple X.25 virtual circuits, this value might identify an (e.g., the first) object instance associated with the X.25 virtual circuit corresponding to this port. For a port which has a unique value of dot1dBasePortIfIndex, this object can have the value { 0 0 }.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

dot1dBasePortDelayExceededDiscards 1.3.6.1.4.1.207.1.4.167.116.1.2.1.4
The number of frames discarded by this port due to excessive transit delay through the bridge. It is incremented by both transparent and source route bridges.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dBasePortMtuExceededDiscards 1.3.6.1.4.1.207.1.4.167.116.1.2.1.5
The number of frames discarded by this port due to an excessive size. It is incremented by both transparent and source route bridges.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dStpTable 1.3.6.1.4.1.207.1.4.167.116.2.1
Table of StpScalars per virtual bridge
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dStpEntry

dot1dStpEntry 1.3.6.1.4.1.207.1.4.167.116.2.1.1
Per bridge StpScalars
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dStpEntry  

dot1dStpContextId 1.3.6.1.4.1.207.1.4.167.116.2.1.1.1
Virtual Bridge number
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

dot1dStpProtocolSpecification 1.3.6.1.4.1.207.1.4.167.116.2.1.1.2
An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If enterprise versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), decLb100(2), ieee8021d(3)  

dot1dStpPriority 1.3.6.1.4.1.207.1.4.167.116.2.1.1.3
The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of dot1dBaseBridgeAddress.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

dot1dStpTimeSinceTopologyChange 1.3.6.1.4.1.207.1.4.167.116.2.1.1.4
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

dot1dStpTopChanges 1.3.6.1.4.1.207.1.4.167.116.2.1.1.5
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dStpDesignatedRoot 1.3.6.1.4.1.207.1.4.167.116.2.1.1.6
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1dStpRootCost 1.3.6.1.4.1.207.1.4.167.116.2.1.1.7
The cost of the path to the root as seen from this bridge.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1dStpRootPort 1.3.6.1.4.1.207.1.4.167.116.2.1.1.8
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1dStpMaxAge 1.3.6.1.4.1.207.1.4.167.116.2.1.1.9
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

dot1dStpHelloTime 1.3.6.1.4.1.207.1.4.167.116.2.1.1.10
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

dot1dStpHoldTime 1.3.6.1.4.1.207.1.4.167.116.2.1.1.11
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1dStpForwardDelay 1.3.6.1.4.1.207.1.4.167.116.2.1.1.12
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

dot1dStpBridgeMaxAge 1.3.6.1.4.1.207.1.4.167.116.2.1.1.13
The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Timeout 600..4000  

dot1dStpBridgeHelloTime 1.3.6.1.4.1.207.1.4.167.116.2.1.1.14
The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Timeout 100..200  

dot1dStpBridgeForwardDelay 1.3.6.1.4.1.207.1.4.167.116.2.1.1.15
The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Timeout 400..3000  

dot1dStpPortTable 1.3.6.1.4.1.207.1.4.167.116.2.2
A table that contains port-specific information for the Spanning Tree Protocol.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dStpPortEntry

dot1dStpPortEntry 1.3.6.1.4.1.207.1.4.167.116.2.2.1
A list of information maintained by every port about the Spanning Tree Protocol state for that port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dStpPortEntry  

dot1dStpPort 1.3.6.1.4.1.207.1.4.167.116.2.2.1.1
The port number of the port for which this entry contains Spanning Tree Protocol management information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

dot1dStpPortPriority 1.3.6.1.4.1.207.1.4.167.116.2.2.1.2
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of dot1dStpPort.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

dot1dStpPortState 1.3.6.1.4.1.207.1.4.167.116.2.2.1.3
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpPortEnable), this object will have a value of disabled(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)  

dot1dStpPortEnable 1.3.6.1.4.1.207.1.4.167.116.2.2.1.4
The enabled/disabled status of the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dot1dStpPortPathCost 1.3.6.1.4.1.207.1.4.167.116.2.2.1.5
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

dot1dStpPortDesignatedRoot 1.3.6.1.4.1.207.1.4.167.116.2.2.1.6
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1dStpPortDesignatedCost 1.3.6.1.4.1.207.1.4.167.116.2.2.1.7
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dot1dStpPortDesignatedBridge 1.3.6.1.4.1.207.1.4.167.116.2.2.1.8
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1dStpPortDesignatedPort 1.3.6.1.4.1.207.1.4.167.116.2.2.1.9
The Port Identifier of the port on the Designated Bridge for this port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

dot1dStpPortForwardTransitions 1.3.6.1.4.1.207.1.4.167.116.2.2.1.10
The number of times this port has transitioned from the Learning state to the Forwarding state.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dTpTable 1.3.6.1.4.1.207.1.4.167.116.4.1
Table of Tp per virtual bridge
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dTpEntry

dot1dTpEntry 1.3.6.1.4.1.207.1.4.167.116.4.1.1
Per bridge TpScalars
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dTpEntry  

dot1dTpLearnedEntryDiscards 1.3.6.1.4.1.207.1.4.167.116.4.1.1.1
The total number of Forwarding Database entries, which have been or would have been learned, but have been discarded due to a lack of space to store them in the Forwarding Database. If this counter is increasing, it indicates that the Forwarding Database is regularly becoming full (a condition which has unpleasant performance effects on the subnetwork). If this counter has a significant value but is not presently increasing, it indicates that the problem has been occurring but is not persistent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dTpAgingTime 1.3.6.1.4.1.207.1.4.167.116.4.1.1.2
The timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..600  

dot1dTpFdbTable 1.3.6.1.4.1.207.1.4.167.116.4.2
A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame. This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dTpFdbEntry

dot1dTpFdbEntry 1.3.6.1.4.1.207.1.4.167.116.4.2.1
Information about a specific unicast MAC address for which the bridge has some forwarding and/or filtering information.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dTpFdbEntry  

dot1dTpFdbAddress 1.3.6.1.4.1.207.1.4.167.116.4.2.1.1
A unicast MAC address for which the bridge has forwarding and/or filtering information.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

dot1dTpFdbPort 1.3.6.1.4.1.207.1.4.167.116.4.2.1.2
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of dot1dTpFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address (e.g. in the dot1dStaticTable). Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of dot1dTpFdbStatus is not learned(3).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1dTpFdbStatus 1.3.6.1.4.1.207.1.4.167.116.4.2.1.3
The status of this entry. The meanings of the values are: other(1) : none of the following. This would include the case where some other MIB object (not the corresponding instance of dot1dTpFdbPort, nor an entry in the dot1dStaticTable) is being used to determine if and how frames addressed to the value of the corresponding instance of dot1dTpFdbAddress are being forwarded. invalid(2) : this entry is not longer valid (e.g., it was learned but has since aged-out), but has not yet been flushed from the table. learned(3) : the value of the corresponding instance of dot1dTpFdbPort was learned, and is being used. self(4) : the value of the corresponding instance of dot1dTpFdbAddress represents one of the bridge's addresses. The corresponding instance of dot1dTpFdbPort indicates which of the bridge's ports has this address. mgmt(5) : the value of the corresponding instance of dot1dTpFdbAddress is also the value of an existing instance of dot1dStaticAddress.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), learned(3), self(4), mgmt(5)  

dot1dTpPortTable 1.3.6.1.4.1.207.1.4.167.116.4.3
A table that contains information about every port that is associated with this transparent bridge.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dTpPortEntry

dot1dTpPortEntry 1.3.6.1.4.1.207.1.4.167.116.4.3.1
A list of information for each port of a transparent bridge.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dTpPortEntry  

dot1dTpPort 1.3.6.1.4.1.207.1.4.167.116.4.3.1.1
The port number of the port for which this entry contains Transparent bridging management information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

dot1dTpPortMaxInfo 1.3.6.1.4.1.207.1.4.167.116.4.3.1.2
The maximum size of the INFO (non-MAC) field that this port will receive or transmit.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1dTpPortInFrames 1.3.6.1.4.1.207.1.4.167.116.4.3.1.3
The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dTpPortOutFrames 1.3.6.1.4.1.207.1.4.167.116.4.3.1.4
The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dTpPortInDiscards 1.3.6.1.4.1.207.1.4.167.116.4.3.1.5
Count of valid frames received which were discarded (i.e., filtered) by the Forwarding Process.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dStaticTable 1.3.6.1.4.1.207.1.4.167.116.5.1
A table containing filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific destination addresses are allowed to be forwarded. The value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for unicast and for group/broadcast addresses.This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dStaticEntry

dot1dStaticEntry 1.3.6.1.4.1.207.1.4.167.116.5.1.1
Filtering information configured into the bridge by (local or network) management specifying the set of ports to which frames received from a specific port and containing a specific destination address are allowed to be forwarded.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dStaticEntry  

dot1dStaticAddress 1.3.6.1.4.1.207.1.4.167.116.5.1.1.1
The destination MAC address in a frame to which this entry's filtering information applies. This object can take the value of a unicast address, a group address or the broadcast address.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

dot1dStaticReceivePort 1.3.6.1.4.1.207.1.4.167.116.5.1.1.2
Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the bridge for which there is no other applicable entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..65535  

dot1dStaticRowStatus 1.3.6.1.4.1.207.1.4.167.116.5.1.1.3
This object indicates the status of the AllowedToGoTo PortList to which a frame with a specific unicast address will be flooded in the event that it has not been learned. To fill the AllowedToGoTo portlist, we have to set the rowstatus as 'NOT_IN_SERVICE' and set the appropriate port in the dot1dStaticAllowedToGoTable and set the rowstatus as 'ACTIVE' to make the portlist available.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dot1dStaticStatus 1.3.6.1.4.1.207.1.4.167.116.5.1.1.4
This object indicates the status of this entry. The default value is permanent(3). other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5)  

dot1dStaticAllowedToGoTable 1.3.6.1.4.1.207.1.4.167.116.5.2
A table containing the information of AllowedToGoTo ports for each static unicast entry. This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dStaticAllowedToGoEntry

dot1dStaticAllowedToGoEntry 1.3.6.1.4.1.207.1.4.167.116.5.2.1
Information about a port, Whether it is an AllowedToGoTo member or not.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dStaticAllowedToGoEntry  

dot1dStaticAllowedIsMember 1.3.6.1.4.1.207.1.4.167.116.5.2.1.1
Indicates whether the port is an allowedToGoTo member.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

newRoot 1.3.6.1.4.1.207.1.4.167.116.0.1
The newRoot trap indicates that the sending agent has become the new root of the Spanning Tree; the trap is sent by a bridge soon after its election as the new root, e.g., upon expiration of the Topology Change Timer immediately subsequent to its election. Implementation of this trap is optional.
Status: current Access: read-write
NOTIFICATION-TYPE    

topologyChange 1.3.6.1.4.1.207.1.4.167.116.0.2
A topologyChange trap is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. The trap is not sent if a newRoot trap is sent for the same transition. Implementation of this trap is optional.
Status: current Access: read-write
NOTIFICATION-TYPE    

dot1dStpExtTable 1.3.6.1.4.1.207.1.4.167.116.2.3
Table of ExtStpScalars per Virtual Context.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dStpExtEntry

dot1dStpExtEntry 1.3.6.1.4.1.207.1.4.167.116.2.3.1
Per Virtual Context Stp Scalars
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dStpExtEntry  

dot1dStpVersion 1.3.6.1.4.1.207.1.4.167.116.2.3.1.1
The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w. New value may be defined as future versions of the protocol become available.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stpCompatible(0), rstp(2)  

dot1dStpTxHoldCount 1.3.6.1.4.1.207.1.4.167.116.2.3.1.2
The value used by the Port Transmit state machine to limit the maximum transmission rate.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

dot1dStpPathCostDefault 1.3.6.1.4.1.207.1.4.167.116.2.3.1.3
The version of the Spanning Tree default Path Costs that are to be used by this Bridge. A value of 8021d1998(1) uses the 16-bit default Path Costs from IEEE Std. 802.1D-1998. A value of stp8021t2001(2) uses the 32-bit default Path Costs from IEEE Std. 802.1t.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stp8021d1998(1), stp8021t2001(2)  

dot1dStpExtPortTable 1.3.6.1.4.1.207.1.4.167.116.2.4
A table that contains port-specific Rapid Spanning Tree information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dStpExtPortEntry

dot1dStpExtPortEntry 1.3.6.1.4.1.207.1.4.167.116.2.4.1
A list of Rapid Spanning Tree information maintained by each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dStpExtPortEntry  

dot1dStpPortProtocolMigration 1.3.6.1.4.1.207.1.4.167.116.2.4.1.1
When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1dStpPortAdminEdgePort 1.3.6.1.4.1.207.1.4.167.116.2.4.1.2
The administrative value of the Edge Port parameter. A value of TRUE(1) indicates that this port should be assumed as an edge-port and a value of FALSE(2) indicates that this port should be assumed as a non-edge-port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1dStpPortOperEdgePort 1.3.6.1.4.1.207.1.4.167.116.2.4.1.3
The operational value of the Edge Port parameter. The object is initialized to the value of dot1dStpPortAdminEdgePort and is set FALSE on reception of a BPDU.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

dot1dStpPortAdminPointToPoint 1.3.6.1.4.1.207.1.4.167.116.2.4.1.4
The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forceTrue(0), forceFalse(1), auto(2)  

dot1dStpPortOperPointToPoint 1.3.6.1.4.1.207.1.4.167.116.2.4.1.5
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the dot1dStpPortAdminPointToPoint object.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

dot1dMIBObjects 1.3.6.1.4.1.207.1.4.167.116.6.1
OBJECT IDENTIFIER    

dot1dExtBase 1.3.6.1.4.1.207.1.4.167.116.6.1.1
OBJECT IDENTIFIER    

dot1dPriority 1.3.6.1.4.1.207.1.4.167.116.6.1.2
OBJECT IDENTIFIER    

dot1dGarp 1.3.6.1.4.1.207.1.4.167.116.6.1.3
OBJECT IDENTIFIER    

dot1dConformance 1.3.6.1.4.1.207.1.4.167.116.6.2
OBJECT IDENTIFIER    

dot1dGroups 1.3.6.1.4.1.207.1.4.167.116.6.2.1
OBJECT IDENTIFIER    

dot1dCompliances 1.3.6.1.4.1.207.1.4.167.116.6.2.2
OBJECT IDENTIFIER    

dot1dExtBaseTable 1.3.6.1.4.1.207.1.4.167.116.6.1.1.1
List of dot1dExtBase group objects that can be configured per virtual context in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dExtBaseEntry

dot1dExtBaseEntry 1.3.6.1.4.1.207.1.4.167.116.6.1.1.1.1
dot1dExtBase group objects per virtual context.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dExtBaseEntry  

dot1dBridgeContextId 1.3.6.1.4.1.207.1.4.167.116.6.1.1.1.1.1
Identifies the virtual context.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

dot1dDeviceCapabilities 1.3.6.1.4.1.207.1.4.167.116.6.1.1.1.1.2
Indicates the optional parts of IEEE 802.1D and 802.1Q that are implemented by this device and are manageable through this MIB. Capabilities that are allowed on a per-port basis are indicated in dot1dPortCapabilities.
Status: current Access: read-only
OBJECT-TYPE    
  BITS dot1dExtendedFilteringServices(0), dot1dTrafficClasses(1), dot1qStaticEntryIndividualPort(2), dot1qIVLCapable(3), dot1qSVLCapable(4), dot1qHybridCapable(5), dot1qConfigurablePvidTagging(6), dot1dLocalVlanCapable(7)  

dot1dTrafficClassesEnabled 1.3.6.1.4.1.207.1.4.167.116.6.1.1.1.1.3
The value true(1) indicates that Traffic Classes are enabled on this bridge. When false(2), the bridge operates with a single priority level for all traffic.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1dGmrpStatus 1.3.6.1.4.1.207.1.4.167.116.6.1.1.1.1.4
The administrative status requested by management for GMRP. The value enabled(1) indicates that GMRP should be enabled on this device, in all VLANs, on all ports for which it has not been specifically disabled. When disabled(2), GMRP is disabled, in all VLANs and on all ports, and all GMRP packets will be forwarded transparently. This object affects both Applicant and Registrar state machines. A transition from disabled(2) to enabled(1) will cause a reset of all GMRP state machines on all ports. The value of this object MUST be retained across reinitializations of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dot1dPortCapabilitiesTable 1.3.6.1.4.1.207.1.4.167.116.6.1.1.2
A table that contains capabilities information about every port that is associated with this bridge.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dPortCapabilitiesEntry

dot1dPortCapabilitiesEntry 1.3.6.1.4.1.207.1.4.167.116.6.1.1.2.1
A set of capabilities information about this port indexed by dot1dBasePort.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dPortCapabilitiesEntry  

dot1dPortCapabilities 1.3.6.1.4.1.207.1.4.167.116.6.1.1.2.1.1
Indicates the parts of IEEE 802.1D and 802.1Q that are optional on a per-port basis that are implemented by this device and are manageable through this MIB.
Status: current Access: read-only
OBJECT-TYPE    
  BITS dot1qDot1qTagging(0), dot1qConfigurableAcceptableFrameTypes(1), dot1qIngressFiltering(2)  

dot1dPortPriorityTable 1.3.6.1.4.1.207.1.4.167.116.6.1.2.1
A table that contains information about every port that is associated with this transparent bridge.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dPortPriorityEntry

dot1dPortPriorityEntry 1.3.6.1.4.1.207.1.4.167.116.6.1.2.1.1
A list of Default User Priorities for each port of a transparent bridge. This is indexed by dot1dBasePort.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dPortPriorityEntry  

dot1dPortDefaultUserPriority 1.3.6.1.4.1.207.1.4.167.116.6.1.2.1.1.1
The default ingress User Priority for this port. This only has effect on media, such as Ethernet, that do not support native User Priority.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

dot1dPortNumTrafficClasses 1.3.6.1.4.1.207.1.4.167.116.6.1.2.1.1.2
The number of egress traffic classes supported on this port. This object may optionally be read-only. The value of this object MUST be retained across reinitializations of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..8  

dot1dUserPriorityRegenTable 1.3.6.1.4.1.207.1.4.167.116.6.1.2.2
A list of Regenerated User Priorities for each received User Priority on each port of a bridge. The Regenerated User Priority value may be used to index the Traffic Class Table for each input port. This only has effect on media that support native User Priority. The default values for Regenerated User Priorities are the same as the User Priorities.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1dUserPriorityRegenEntry

dot1dUserPriorityRegenEntry 1.3.6.1.4.1.207.1.4.167.116.6.1.2.2.1
A mapping of incoming User Priority to a Regenerated User Priority.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dot1dUserPriorityRegenEntry  

dot1dUserPriority 1.3.6.1.4.1.207.1.4.167.116.6.1.2.2.1.1
The User Priority for a frame received on this port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7  

dot1dRegenUserPriority 1.3.6.1.4.1.207.1.4.167.116.6.1.2.2.1.2
The Regenerated User Priority that the incoming User Priority is mapped to for this port. The value of this object MUST be retained across reinitializations of the management system.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

dot1dTrafficClassTable 1.3.6.1.4.1.207.1.4.167.116.6.1.2.3
A table mapping evaluated User Priority to Traffic Class, for forwarding by the bridge. Traffic class is a number in the range (0..(dot1dPortNumTrafficClasses-1)).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dTrafficClassEntry

dot1dTrafficClassEntry 1.3.6.1.4.1.207.1.4.167.116.6.1.2.3.1
User Priority to Traffic Class mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dTrafficClassEntry  

dot1dTrafficClassPriority 1.3.6.1.4.1.207.1.4.167.116.6.1.2.3.1.1
The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type. For untagged frames received from Ethernet media, this value is equal to the dot1dPortDefaultUserPriority value for the ingress port. For untagged frames received from non-Ethernet media, this value is equal to the dot1dRegenUserPriority value for the ingress port and media-specific user priority.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..7  

dot1dTrafficClass 1.3.6.1.4.1.207.1.4.167.116.6.1.2.3.1.2
The Traffic Class the received frame is mapped to.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

dot1dPortOutboundAccessPriorityTable 1.3.6.1.4.1.207.1.4.167.116.6.1.2.4
A table mapping Regenerated User Priority to Outbound Access Priority. This is a fixed mapping for all port types, with two options for 802.5 Token Ring.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1dPortOutboundAccessPriorityEntry

dot1dPortOutboundAccessPriorityEntry 1.3.6.1.4.1.207.1.4.167.116.6.1.2.4.1
Regenerated User Priority to Outbound Access Priority mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dot1dPortOutboundAccessPriorityEntry  

dot1dPortOutboundAccessPriority 1.3.6.1.4.1.207.1.4.167.116.6.1.2.4.1.1
The Outbound Access Priority the received frame is mapped to.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..7  

dot1dPortGarpTable 1.3.6.1.4.1.207.1.4.167.116.6.1.3.1
A table of GARP control information about every bridge port. This is indexed by dot1dBasePort.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dPortGarpEntry

dot1dPortGarpEntry 1.3.6.1.4.1.207.1.4.167.116.6.1.3.1.1
GARP control information for a bridge port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dPortGarpEntry  

dot1dPortGarpJoinTime 1.3.6.1.4.1.207.1.4.167.116.6.1.3.1.1.1
The GARP Join time, in centiseconds.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

dot1dPortGarpLeaveTime 1.3.6.1.4.1.207.1.4.167.116.6.1.3.1.1.2
The GARP Leave time, in centiseconds.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

dot1dPortGarpLeaveAllTime 1.3.6.1.4.1.207.1.4.167.116.6.1.3.1.1.3
The GARP LeaveAll time, in centiseconds.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

dot1dTpHCPortTable 1.3.6.1.4.1.207.1.4.167.116.4.5
A table that contains information about every high capacity port that is associated with this transparent bridge.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dTpHCPortEntry

dot1dTpHCPortEntry 1.3.6.1.4.1.207.1.4.167.116.4.5.1
Statistics information for each high capacity port of a transparent bridge.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dTpHCPortEntry  

dot1dTpHCPortInFrames 1.3.6.1.4.1.207.1.4.167.116.4.5.1.1
The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dot1dTpHCPortOutFrames 1.3.6.1.4.1.207.1.4.167.116.4.5.1.2
The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dot1dTpHCPortInDiscards 1.3.6.1.4.1.207.1.4.167.116.4.5.1.3
Count of valid frames that have been received by this port from its segment which were discarded (i.e., filtered) by the Forwarding Process.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dot1dTpPortOverflowTable 1.3.6.1.4.1.207.1.4.167.116.4.6
A table that contains the most-significant bits of statistics counters for ports that are associated with this transparent bridge that are on high capacity interfaces, as defined in the conformance clauses for this table. This table is provided as a way to read 64-bit counters for agents which support only SNMPv1. Note that the reporting of most-significant and least-significant counter bits separately runs the risk of missing an overflow of the lower bits in the interval between sampling. The manager must be aware of this possibility, even within the same varbindlist, when interpreting the results of a request or asynchronous notification.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1dTpPortOverflowEntry

dot1dTpPortOverflowEntry 1.3.6.1.4.1.207.1.4.167.116.4.6.1
The most significant bits of statistics counters for a high capacity interface of a transparent bridge. Each object is associated with a corresponding object in dot1dTpPortTable which indicates the least significant bits of the counter.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1dTpPortOverflowEntry  

dot1dTpPortInOverflowFrames 1.3.6.1.4.1.207.1.4.167.116.4.6.1.1
The number of times the associated dot1dTpPortInFrames counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dTpPortOutOverflowFrames 1.3.6.1.4.1.207.1.4.167.116.4.6.1.2
The number of times the associated dot1dTpPortOutFrames counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dTpPortInOverflowDiscards 1.3.6.1.4.1.207.1.4.167.116.4.6.1.3
The number of times the associated dot1dTpPortInDiscards counter has overflowed.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1dExtCapGroup 1.3.6.1.4.1.207.1.4.167.116.6.2.1.1
A collection of objects indicating the optional capabilities of the device.
Status: current Access: read-only
OBJECT-GROUP    

dot1dDeviceGmrpGroup 1.3.6.1.4.1.207.1.4.167.116.6.2.1.2
A collection of objects providing device-level control for the Multicast Filtering extended bridge services.
Status: current Access: read-only
OBJECT-GROUP    

dot1dDevicePriorityGroup 1.3.6.1.4.1.207.1.4.167.116.6.2.1.3
A collection of objects providing device-level control for the Priority services.
Status: current Access: read-only
OBJECT-GROUP    

dot1dDefaultPriorityGroup 1.3.6.1.4.1.207.1.4.167.116.6.2.1.4
A collection of objects defining the User Priority applicable to each port for media which do not support native User Priority.
Status: current Access: read-only
OBJECT-GROUP    

dot1dRegenPriorityGroup 1.3.6.1.4.1.207.1.4.167.116.6.2.1.5
A collection of objects defining the User Priorities applicable to each port for media which support native User Priority.
Status: current Access: read-only
OBJECT-GROUP    

dot1dPriorityGroup 1.3.6.1.4.1.207.1.4.167.116.6.2.1.6
A collection of objects defining the traffic classes within a bridge for each evaluated User Priority.
Status: current Access: read-only
OBJECT-GROUP    

dot1dAccessPriorityGroup 1.3.6.1.4.1.207.1.4.167.116.6.2.1.7
A collection of objects defining the media dependent outbound access level for each priority.
Status: current Access: read-only
OBJECT-GROUP    

dot1dPortGarpGroup 1.3.6.1.4.1.207.1.4.167.116.6.2.1.8
A collection of objects providing port level control and status information for GARP operation.
Status: current Access: read-only
OBJECT-GROUP    

dot1dHCPortGroup 1.3.6.1.4.1.207.1.4.167.116.6.2.1.10
A collection of objects providing 64-bit statistics counters for high capacity bridge ports.
Status: current Access: read-only
OBJECT-GROUP    

dot1dPortOverflowGroup 1.3.6.1.4.1.207.1.4.167.116.6.2.1.11
A collection of objects providing overflow statistics counters for high capacity bridge ports.
Status: current Access: read-only
OBJECT-GROUP    

dot1dCompliance 1.3.6.1.4.1.207.1.4.167.116.6.2.2.1
The compliance statement for device support of Priority and Multicast Filtering extended bridging services.
Status: current Access: read-only
MODULE-COMPLIANCE    

dot1qMIBObjects 1.3.6.1.4.1.207.1.4.167.116.7.1
OBJECT IDENTIFIER    

dot1qBase 1.3.6.1.4.1.207.1.4.167.116.7.1.1
OBJECT IDENTIFIER    

dot1qTp 1.3.6.1.4.1.207.1.4.167.116.7.1.2
OBJECT IDENTIFIER    

dot1qStatic 1.3.6.1.4.1.207.1.4.167.116.7.1.3
OBJECT IDENTIFIER    

dot1qVlan 1.3.6.1.4.1.207.1.4.167.116.7.1.4
OBJECT IDENTIFIER    

dot1qBaseTable 1.3.6.1.4.1.207.1.4.167.116.7.1.1.1
List of dot1qBase objects that can be configured per virtual context in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qBaseEntry

dot1qBaseEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.1.1.1
Virtual context dot1qBase objects.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qBaseEntry  

dot1qVlanContextId 1.3.6.1.4.1.207.1.4.167.116.7.1.1.1.1.1
Identifies a virtual context.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

dot1qVlanVersionNumber 1.3.6.1.4.1.207.1.4.167.116.7.1.1.1.1.2
The version number of IEEE 802.1Q that this device supports.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER version1(1)  

dot1qMaxVlanId 1.3.6.1.4.1.207.1.4.167.116.7.1.1.1.1.3
The maximum IEEE 802.1Q VLAN ID that this device supports.
Status: current Access: read-only
OBJECT-TYPE    
  VlanId  

dot1qMaxSupportedVlans 1.3.6.1.4.1.207.1.4.167.116.7.1.1.1.1.4
The maximum number of IEEE 802.1Q VLANs that this device supports.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

dot1qNumVlans 1.3.6.1.4.1.207.1.4.167.116.7.1.1.1.1.5
The current number of IEEE 802.1Q VLANs that are configured in this device.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

dot1qGvrpStatus 1.3.6.1.4.1.207.1.4.167.116.7.1.1.1.1.6
The administrative status requested by management for GVRP. The value enabled(1) indicates that GVRP should be enabled on this device, on all ports for which it has not been specifically disabled. When disabled(2), GVRP is disabled on all ports and all GVRP packets will be forwarded transparently. This object affects all GVRP Applicant and Registrar state machines. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on all ports.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

dot1qFdbTable 1.3.6.1.4.1.207.1.4.167.116.7.1.2.1
A table that contains configuration and control information for each Filtering Database currently operating on this device. Entries in this table appear automatically when VLANs are assigned FDB IDs in the dot1qVlanCurrentTable. This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qFdbEntry

dot1qFdbEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.2.1.1
Information about a specific Filtering Database.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qFdbEntry  

dot1qFdbId 1.3.6.1.4.1.207.1.4.167.116.7.1.2.1.1.1
The identity of this Filtering Database.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

dot1qFdbDynamicCount 1.3.6.1.4.1.207.1.4.167.116.7.1.2.1.1.2
The current number of dynamic entries in this Filtering Database.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1qTpFdbTable 1.3.6.1.4.1.207.1.4.167.116.7.1.2.2
A table that contains information about unicast entries for which the device has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame. This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qTpFdbEntry

dot1qTpFdbEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.2.2.1
Information about a specific unicast MAC address for which the device has some forwarding and/or filtering information.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qTpFdbEntry  

dot1qTpFdbAddress 1.3.6.1.4.1.207.1.4.167.116.7.1.2.2.1.1
A unicast MAC address for which the device has forwarding and/or filtering information.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

dot1qTpFdbPort 1.3.6.1.4.1.207.1.4.167.116.7.1.2.2.1.2
Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance of dot1qTpFdbAddress has been seen. A value of '0' indicates that the port number has not been learned but that the device does have some forwarding/filtering information about this address (e.g. in the dot1qStaticUnicastTable). Implementors are encouraged to assign the port value to this object whenever it is learned even for addresses for which the corresponding value of dot1qTpFdbStatus is not learned(3).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

dot1qTpFdbStatus 1.3.6.1.4.1.207.1.4.167.116.7.1.2.2.1.3
The status of this entry. The meanings of the values are: other(1) - none of the following. This may include the case where some other MIB object (not the corresponding instance of dot1qTpFdbPort, nor an entry in the dot1qStaticUnicastTable) is being used to determine if and how frames addressed to the value of the corresponding instance of dot1qTpFdbAddress are being forwarded. invalid(2) - this entry is no longer valid (e.g., it was learned but has since aged out), but has not yet been flushed from the table. learned(3) - the value of the corresponding instance of dot1qTpFdbPort was learned and is being used. self(4) - the value of the corresponding instance of dot1qTpFdbAddress represents one of the device's addresses. The corresponding instance of dot1qTpFdbPort indicates which of the device's ports has this address. mgmt(5) - the value of the corresponding instance of dot1qTpFdbAddress is also the value of an existing instance of dot1qStaticAddress.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), learned(3), self(4), mgmt(5)  

dot1qTpFdbPw 1.3.6.1.4.1.207.1.4.167.116.7.1.2.2.1.4
Either the value '0', or the pseudowire number on which a frame having a source address equal to the value of the corresponding instance of dot1qTpFdbAddress has been seen. A value of '0' indicates that the entry was learned via the layer2 port. Non-zero value indicates that this value must be used for forwading irrespective of dot1qTpFdbPort
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

dot1qStaticUnicastTable 1.3.6.1.4.1.207.1.4.167.116.7.1.3.1
A table containing filtering information for Unicast MAC addresses for each Filtering Database, configured into the device by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific unicast destination addresses are allowed to be forwarded. A value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for unicast addresses only. This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qStaticUnicastEntry

dot1qStaticUnicastEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.3.1.1
Filtering information configured into the device by (local or network) management specifying the set of ports to which frames received from a specific port and containing a specific unicast destination address are allowed to be forwarded.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qStaticUnicastEntry  

dot1qStaticUnicastAddress 1.3.6.1.4.1.207.1.4.167.116.7.1.3.1.1.1
The destination MAC address in a frame to which this entry's filtering information applies. This object must take the value of a unicast address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

dot1qStaticUnicastReceivePort 1.3.6.1.4.1.207.1.4.167.116.7.1.3.1.1.2
Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the device for which there is no other applicable entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

dot1qStaticUnicastRowStatus 1.3.6.1.4.1.207.1.4.167.116.7.1.3.1.1.3
This object indicates the status of the AllowedToGoTo PortList to which a frame with a specific unicast address will be flooded in the event that it has not been learned. To fill the AllowedToGoTo portlist, we have to set the rowstatus as 'NOT_IN_SERVICE' and set the appropriate port in the dot1qStaticAllowedToGoTable and set the rowstatus as 'ACTIVE' to make the portlist available.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dot1qStaticUnicastStatus 1.3.6.1.4.1.207.1.4.167.116.7.1.3.1.1.4
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5)  

dot1qStaticAllowedToGoTable 1.3.6.1.4.1.207.1.4.167.116.7.1.3.2
A table containing the information of AllowedToGoTo ports for each static unicast entry. This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qStaticAllowedToGoEntry

dot1qStaticAllowedToGoEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.3.2.1
Information about a port, Whether it is an AllowedToGoTo member or not.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qStaticAllowedToGoEntry  

dot1qStaticAllowedIsMember 1.3.6.1.4.1.207.1.4.167.116.7.1.3.2.1.1
Indicates whether the port is an allowedToGoTo member.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1qTpPort 1.3.6.1.4.1.207.1.4.167.116.7.1.3.2.1.2
The port number of the port for which this entry applies.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

dot1qStaticMulticastTable 1.3.6.1.4.1.207.1.4.167.116.7.1.3.3
A table containing filtering information for Multicast and Broadcast MAC addresses for each VLAN, configured into the device by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific Multicast and Broadcast destination addresses are allowed to be forwarded. A value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for Multicast and Broadcast addresses only. This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qStaticMulticastEntry

dot1qStaticMulticastEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.3.3.1
Filtering information configured into the device by (local or network) management specifying the set of ports to which frames received from this specific port for this VLAN and containing this Multicast or Broadcast destination address are allowed to be forwarded.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qStaticMulticastEntry  

dot1qStaticMulticastAddress 1.3.6.1.4.1.207.1.4.167.116.7.1.3.3.1.1
The destination MAC address in a frame to which this entry's filtering information applies. This object must take the value of a Multicast or Broadcast address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

dot1qStaticMulticastReceivePort 1.3.6.1.4.1.207.1.4.167.116.7.1.3.3.1.2
Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of zero indicates that this entry applies on all ports of the device for which there is no other applicable entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

dot1qStaticMulticastRowStatus 1.3.6.1.4.1.207.1.4.167.116.7.1.3.3.1.3
This object indicates the status of the PortLists (Eggress, Forbidden) used in the static multicast table. To fill the eggress and forbidden portlist, we have to set the rowstatus as 'NOT_IN_SERVICE' and set the appropriate port in the dot1qForwardUnregPortConfigTable and set the rowstatus as 'ACTIVE' to make the portlist available.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dot1qStaticMulticastStatus 1.3.6.1.4.1.207.1.4.167.116.7.1.3.3.1.4
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5)  

dot1qStaticMcastPortTable 1.3.6.1.4.1.207.1.4.167.116.7.1.3.4
A table containing egress and forbidden ports for static multicast entry. This table maintains context ID as one more index to support Multiple Instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qStaticMcastPortEntry

dot1qStaticMcastPortEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.3.4.1
Information about a port, Whether it is a member or a forbidden member.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qStaticMcastPortEntry  

dot1qStaticMcastPort 1.3.6.1.4.1.207.1.4.167.116.7.1.3.4.1.1
Indicates whether the port is a member or a forbidden member in the static multicast entry. 'addMember' - to add the port in the egress member-list. 'addForbidden' - to add the port in the forbidden member-list. 'delMember' - to remove the port from the egress member-list. 'delForbidden' - to remove the port from the forbidden member-list.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER addMember(1), addForbidden(2), delMember(3), delForbidden(4)  

dot1qVlanIndex 1.3.6.1.4.1.207.1.4.167.116.7.1.3.4.1.2
The VLAN-ID or other identifier referring to this VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanIndex  

dot1qVlanNumDeletesTable 1.3.6.1.4.1.207.1.4.167.116.7.1.4.1
Table containing number of VLAN deletions in the VLAN current database. This table maintains context ID as index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qVlanNumDeletesEntry

dot1qVlanNumDeletesEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.4.1.1
Entry for a virtual context.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qVlanNumDeletesEntry  

dot1qVlanNumDeletes 1.3.6.1.4.1.207.1.4.167.116.7.1.4.1.1.1
The number of times a VLAN entry has been deleted from the dot1qVlanCurrentTable (for any reason). If an entry is deleted, then inserted, and then deleted, this counter will be incremented by 2.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1qVlanCurrentTable 1.3.6.1.4.1.207.1.4.167.116.7.1.4.2
A table containing current configuration information for each VLAN currently configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received. This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qVlanCurrentEntry

dot1qVlanCurrentEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.4.2.1
Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qVlanCurrentEntry  

dot1qVlanTimeMark 1.3.6.1.4.1.207.1.4.167.116.7.1.4.2.1.1
A TimeFilter for this entry. See the TimeFilter textual convention to see how this works.
Status: current Access: not-accessible
OBJECT-TYPE    
  TimeFilter  

dot1qVlanFdbId 1.3.6.1.4.1.207.1.4.167.116.7.1.4.2.1.2
The Filtering Database used by this VLAN. This is one of the dot1qFdbId values in the dot1qFdbTable. This value is allocated automatically by the device whenever the VLAN is created: either dynamically by GVRP, or by management, in dot1qVlanStaticTable. Allocation of this value follows the learning constraints defined for this VLAN in dot1qLearningConstraintsTable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

dot1qVlanStatus 1.3.6.1.4.1.207.1.4.167.116.7.1.4.2.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. permanent(2) - this entry, corresponding to an entry in dot1qVlanStaticTable, is currently in use and will remain so after the next reset of the device. The port lists for this entry include ports from the equivalent dot1qVlanStaticTable entry and ports learnt dynamically. dynamicGvrp(3) - this entry is currently in use and will remain so until removed by GVRP. There is no static entry for this VLAN and it will be removed when the last port leaves the VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), permanent(2), dynamicGvrp(3)  

dot1qVlanCreationTime 1.3.6.1.4.1.207.1.4.167.116.7.1.4.2.1.4
The value of sysUpTime when this VLAN was created.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

dot1qVlanEgressPortTable 1.3.6.1.4.1.207.1.4.167.116.7.1.4.3
A table containing the information of egress ports for each VLAN. This table maintains context ID as one more index to support Multiple Instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qVlanEgressPortEntry

dot1qVlanEgressPortEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.4.3.1
Information about a port, Whether it is a tagged or an untagged member.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qVlanEgressPortEntry  

dot1qVlanCurrentEgressPort 1.3.6.1.4.1.207.1.4.167.116.7.1.4.3.1.1
Indicates whether the port is a tagged or a untagged member in the VLAN. 'tagged' - to add the port in the tagged portlist. 'untagged' - to add the port in the untagged portlist.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER tagged(1), untagged(2)  

dot1qVlanStaticTable 1.3.6.1.4.1.207.1.4.167.116.7.1.4.4
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset. This table maintains context ID as one more index to support Multiple Instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qVlanStaticEntry

dot1qVlanStaticEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.4.4.1
Static information for a VLAN configured into the device by (local or network) management.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qVlanStaticEntry  

dot1qVlanStaticName 1.3.6.1.4.1.207.1.4.167.116.7.1.4.4.1.1
An administratively assigned string, which may be used to identify the VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

dot1qVlanStaticRowStatus 1.3.6.1.4.1.207.1.4.167.116.7.1.4.4.1.2
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dot1qVlanStaticPortConfigTable 1.3.6.1.4.1.207.1.4.167.116.7.1.4.5
A table containing the information of tagged, untagged and forbidden ports for each VLAN. This table maintains context ID as one more index to support Multiple Instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qVlanStaticPortConfigEntry

dot1qVlanStaticPortConfigEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.4.5.1
Forwarding information about a port, Whether it is a member or a forbidden member.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qVlanStaticPortConfigEntry  

dot1qVlanStaticPort 1.3.6.1.4.1.207.1.4.167.116.7.1.4.5.1.1
Indicates whether the port is a member or a forbidden member in the forwarding information for this VLAN. 'addTagged' - to add the port in the tagged portlist. 'addUntagged' - to add the port in the untagged portlist. 'addForbidden' - to add the port in the forbidden portlist. 'delTagged' - to delete the port from the tagged portlist. 'delUntagged' - to delete the port from the untagged portlist. 'delForbidden' - to delete the port from the forbidden portlist.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER addTagged(1), addUntagged(2), addForbidden(3), delTagged(4), delUntagged(5), delForbidden(6)  

dot1qPortVlanTable 1.3.6.1.4.1.207.1.4.167.116.7.1.4.7
A table containing per port control and status information for VLAN configuration in the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qPortVlanEntry

dot1qPortVlanEntry 1.3.6.1.4.1.207.1.4.167.116.7.1.4.7.1
Information controlling VLAN configuration for a port on the device. This is indexed by dot1dBasePort.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qPortVlanEntry  

dot1qPvid 1.3.6.1.4.1.207.1.4.167.116.7.1.4.7.1.1
The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

dot1qPortAcceptableFrameTypes 1.3.6.1.4.1.207.1.4.167.116.7.1.4.7.1.2
When this is admitOnlyVlanTagged(2) the device will discard untagged frames or Priority-Tagged frames received on this port. When admitAll(1), untagged frames or Priority-Tagged frames received on this port will be accepted and assigned to the PVID for this port. When this is admitOnlyUntaggedAndPriorityTagged the device will recieve only untagged and priority tagged frames on this port. This control does not affect VLAN independent BPDU frames, such as GVRP and STP. It does affect VLAN dependent BPDU frames, such as GMRP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER admitAll(1), admitOnlyVlanTagged(2), admitOnlyUntaggedAndPriorityTagged(3)  

dot1qPortIngressFiltering 1.3.6.1.4.1.207.1.4.167.116.7.1.4.7.1.3
When this is true(1) the device will discard incoming frames for VLANs which do not include this Port in its Member set. When false(2), the port will accept all incoming frames. This control does not affect VLAN independent BPDU frames, such as GVRP and STP. It does affect VLAN dependent BPDU frames, such as GMRP.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1qPortGvrpStatus 1.3.6.1.4.1.207.1.4.167.116.7.1.4.7.1.4
The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dot1qPortGvrpFailedRegistrations 1.3.6.1.4.1.207.1.4.167.116.7.1.4.7.1.5
The total number of failed GVRP registrations, for any reason, on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1qPortGvrpLastPduOrigin 1.3.6.1.4.1.207.1.4.167.116.7.1.4.7.1.6
The Source MAC Address of the last GVRP message received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

dot1qPortRestrictedVlanRegistration 1.3.6.1.4.1.207.1.4.167.116.7.1.4.7.1.7
The state of Restricted VLAN Registration on this port. If the value of this control is true(1), then creation of a new dynamic VLAN entry is permitted only if there is a Static VLAN Registration Entry for the VLAN concerned, in which the Registrar Administrative Control value for this port is Normal Registration.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1sMst 1.3.6.1.4.1.207.1.4.167.118.1
OBJECT IDENTIFIER    

dot1sMstTrapsControl 1.3.6.1.4.1.207.1.4.167.118.2
OBJECT IDENTIFIER    

dot1sMstTraps 1.3.6.1.4.1.207.1.4.167.118.3
OBJECT IDENTIFIER    

dot1sMstTable 1.3.6.1.4.1.207.1.4.167.118.1.3
List of per Virtual Context Mst Module Parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1sMstEntry

dot1sMstEntry 1.3.6.1.4.1.207.1.4.167.118.1.3.1
Virtual Context Mst Module Parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1sMstEntry  

dot1sMstContextId 1.3.6.1.4.1.207.1.4.167.118.1.3.1.1
Identifies the Virtual Context.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

dot1sSystemControl 1.3.6.1.4.1.207.1.4.167.118.1.3.1.2
The administrative shutdown status requested by management for the MST feature. The value start (1) indicates that MST should be active in the device on all ports. The value shutdown (2) indicates that MST should be shutdown in the device on all ports. All memory should be released on all ports.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER start(1), shutdown(2)  

dot1sModuleStatus 1.3.6.1.4.1.207.1.4.167.118.1.3.1.3
The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, dot1sSystemControl set to start.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dot1sMaxMstInstanceNumber 1.3.6.1.4.1.207.1.4.167.118.1.3.1.4
The Maximun number of spanning trees to be allowed. A User may limit the Number of Spanning Tree instance to be allowed in the Bridge.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..64  

dot1sNoOfMstiSupported 1.3.6.1.4.1.207.1.4.167.118.1.3.1.5
Indicates Maximum number of spanning tree Instances supported.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sMaxHopCount 1.3.6.1.4.1.207.1.4.167.118.1.3.1.6
Indicates the Maximum Hop Count value. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 600..4000  

dot1sBrgAddress 1.3.6.1.4.1.207.1.4.167.118.1.3.1.7
The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1sCistBridgePriority or dot1sMstiBridgePriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

dot1sCistRoot 1.3.6.1.4.1.207.1.4.167.118.1.3.1.8
The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1sCistRegionalRoot 1.3.6.1.4.1.207.1.4.167.118.1.3.1.9
The bridge identifier of the Root of the Multiple spanning tree region as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Regional Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1sCistRootCost 1.3.6.1.4.1.207.1.4.167.118.1.3.1.10
The Cost of the path to the CIST Root as seen from this bridge.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sCistRegionalRootCost 1.3.6.1.4.1.207.1.4.167.118.1.3.1.11
The Cost of the path to the CIST Regional Root as seen from this bridge.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sCistRootPort 1.3.6.1.4.1.207.1.4.167.118.1.3.1.12
The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sCistBridgePriority 1.3.6.1.4.1.207.1.4.167.118.1.3.1.13
The Value of the writable portion of the Bridge Identifier comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..61440  

dot1sCistBridgeMaxAge 1.3.6.1.4.1.207.1.4.167.118.1.3.1.14
The value that all bridges use for MaxAge when this bridge is acting as the root. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Timeout 600..4000  

dot1sCistBridgeForwardDelay 1.3.6.1.4.1.207.1.4.167.118.1.3.1.15
The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D specifies that the range for this parameter is related to the value of BridgeMaxAge. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Timeout 400..3000  

dot1sCistHoldTime 1.3.6.1.4.1.207.1.4.167.118.1.3.1.16
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sCistMaxAge 1.3.6.1.4.1.207.1.4.167.118.1.3.1.17
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

dot1sCistForwardDelay 1.3.6.1.4.1.207.1.4.167.118.1.3.1.18
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in a particular state before moving to the next state.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

dot1sMstpUpCount 1.3.6.1.4.1.207.1.4.167.118.1.3.1.19
The number of times MSTP Module has been enabled.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sMstpDownCount 1.3.6.1.4.1.207.1.4.167.118.1.3.1.20
The number of times MSTP Module has been disabled.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sPathCostDefaultType 1.3.6.1.4.1.207.1.4.167.118.1.3.1.21
The version of the Spanning Tree default Path Costs that are to be used by this Bridge. A value of 8021d1998(1) uses the 16-bit default Path Costs from IEEE Std. 802.1D-1998. A value of stp8021t2001(2) uses the 32-bit default Path Costs from IEEE Std. 802.1t.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stp8021d1998(1), stp8021t2001(2)  

dot1sTrace 1.3.6.1.4.1.207.1.4.167.118.1.3.1.22
This object is used to enable Trace Statements in the MSTP Module. A FOUR BYTE integer is used for enabling the level of tracing. Each BIT in the four byte integer, represents a particular level of Trace. The mapping between the bit positions & the level of trace is as follows: 0 - Init and Shutdown Traces 1 - Management Traces 2 - Data Path Traces 3 - Control Plane Traces 4 - Packet Dump Traces 5 - Traces related to All Resources except Buffers 6 - All Failure Traces 7 - Buffer Traces The remaining bits are unused. Combination of trace levels are also allowed. For example if the bits 0 and 1 are set, then the Trace statements related to Init-Shutdown and management will be printed. The user has to enter the corresponding INTEGER VALUE for the bits set. For example if bits 0 and 1 are to be set then user has to give the value for this object as 3. Setting the Trace Option to any value will cause the Debug Option to be set to 0 (i.e.) the Trace Option and Debug Option are mutually exclusive.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

dot1sDebug 1.3.6.1.4.1.207.1.4.167.118.1.3.1.23
This object is used to enable Debug Statements in the MSTP Module. A FOUR BYTE integer is used for enabling the level of debugging. Each BIT in the four byte integer, represents a particular level of Debug. The mapping between the bit positions & the level of debug is as follows: 0 - Init and Shutdown Debug statements 1 - Management Debug statements 2 - Memory related Debug statements 3 - BPDU related Debug statements 4 - Event Handling Debug statements 5 - Timer Module Debug statements 6 - Port Information SEM Debug statements 7 - Port Receive SEM Debug statements (valid in the case of MSTP alone) 8 - Role Selection SEM Debug statements 9 - Role Transition SEM Debug statements 10 - State Transition SEM Debug statements 11 - Protocol Migration SEM Debug statements 12 - Topology Change SEM Debug statements 13 - Port Transmit SEM Debug statements 14 - Bridge Detection SEM Debug statements 15 - All Failure Debug statements 16 - Redundancy code flow Debug statements The remaining bits are unused. Combination of debug levels are also allowed. For example if the bits 0 and 1 are set, then the Debug statements related to Init-Shutdown and management will be printed. The user has to enter the corresponding INTEGER VALUE for the bits set. For example if bits 0 and 1 are to be set then user has to give the value for this object as 3. Setting the Debug Option to any value will cause the Trace Option to be set to 0 (i.e.) the Trace Option and Debug Option are mutually exclusive.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..131071  

dot1sForceProtocolVersion 1.3.6.1.4.1.207.1.4.167.118.1.3.1.24
The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w and 'mstp(3)' indicates the Multiple Spanning Tree Protocol Specified in IEEE 802.1s.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stpCompatible(0), rstp(2), mstp(3)  

dot1sTxHoldCount 1.3.6.1.4.1.207.1.4.167.118.1.3.1.25
The value used by the Port Transmit state machine to limit the maximum transmission rate.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

dot1sMstiConfigIdSel 1.3.6.1.4.1.207.1.4.167.118.1.3.1.26
The Configuration Identifier Format Selector used by the Bridge. This has a fixed value of 0 to indicate RegionName, RegionVersion are specified as in Standard.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

dot1sMstiRegionName 1.3.6.1.4.1.207.1.4.167.118.1.3.1.27
The Name for the Region's configuration. By Default Region Name will be equal to the Bridge Mac Address.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

dot1sMstiRegionVersion 1.3.6.1.4.1.207.1.4.167.118.1.3.1.28
Version of the MST Region.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

dot1sMstiConfigDigest 1.3.6.1.4.1.207.1.4.167.118.1.3.1.29
The Configuration Digest value for this Region.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

dot1sBufferOverFlowCount 1.3.6.1.4.1.207.1.4.167.118.1.3.1.30
The number of times Buffer overflows/failures have occured. A Trap is generated on the occurence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sMemAllocFailureCount 1.3.6.1.4.1.207.1.4.167.118.1.3.1.31
The number of times memory allocation failures have occured. A Trap is generated on the occurence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sRegionConfigChangeCount 1.3.6.1.4.1.207.1.4.167.118.1.3.1.32
The number of times a Region Configuration Identifier Change was detected. A Trap is generated on the occurence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistBridgeRoleSelectionSemState 1.3.6.1.4.1.207.1.4.167.118.1.3.1.33
Current state of the Port Role Selection State Machine of this bridge in Common Spanning Tree context
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initbridge(0), roleselection(1)  

dot1sCistTimeSinceTopologyChange 1.3.6.1.4.1.207.1.4.167.118.1.3.1.34
The time (in hundredths of a second) since the TcWhile Timer for any port in this Bridge was non-zero for Common Spanning Tree context.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

dot1sCistTopChanges 1.3.6.1.4.1.207.1.4.167.118.1.3.1.35
The number of times that there have been atleast one non-zero TcWhile Timer on this Bridge for Common Spanning Tree context.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistNewRootBridgeCount 1.3.6.1.4.1.207.1.4.167.118.1.3.1.36
The number of times this Bridge has detected a Root Bridge change for Common Spanning Tree context. A Trap is generated on the occurence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistHelloTime 1.3.6.1.4.1.207.1.4.167.118.1.3.1.37
This time value, measured in units of hundredths of a second, specifies the amount of time between the transmission of configuration BPDUs by this node on any port when it is the root of the spanning tree or trying to become so.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

dot1sCistBridgeHelloTime 1.3.6.1.4.1.207.1.4.167.118.1.3.1.38
The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.
Status: current Access: read-write
OBJECT-TYPE    
  Timeout 100..200  

dot1sCistDynamicPathcostCalculation 1.3.6.1.4.1.207.1.4.167.118.1.3.1.39
This object is used to determine whether dynamic pathcost calculation is allowed or not.The value is determined by management. If set to true, pathcost is calculated dynamically from port speed, otherwise the link speed at the time of port creation is used for calculating the path cost. In both cases if the user has configured a pathcost for the port that will be used. By default dynamic pathcost calculation is set to false.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1sContextName 1.3.6.1.4.1.207.1.4.167.118.1.3.1.40
This object is used to identity the context-name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

dot1sMstiBridgeTable 1.3.6.1.4.1.207.1.4.167.118.1.4
Table containing Bridge Information specific to Spanning Tree Instance. This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1sMstiBridgeEntry

dot1sMstiBridgeEntry 1.3.6.1.4.1.207.1.4.167.118.1.4.1
Entry indicating the Bridge Information.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1sMstiBridgeEntry  

dot1sMstiInstanceIndex 1.3.6.1.4.1.207.1.4.167.118.1.4.1.1
Spanning Tree Instance to which the information belongs.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..64  

dot1sMstiBridgeRegionalRoot 1.3.6.1.4.1.207.1.4.167.118.1.4.1.2
MSTI Regional Root Identifier value for the Instance. This value is used as the MSTI Regional Root Identifier parameter in all Configuration Bridge PDUs originated by this node
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1sMstiBridgePriority 1.3.6.1.4.1.207.1.4.167.118.1.4.1.3
The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..61440  

dot1sMstiRootCost 1.3.6.1.4.1.207.1.4.167.118.1.4.1.4
The Cost of the path to the MSTI Regional Root as seen by this bridge.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sMstiRootPort 1.3.6.1.4.1.207.1.4.167.118.1.4.1.5
The Port Number of the Port which offers the lowest path cost from this bridge to the MSTI Region Root Bridge.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sMstiTimeSinceTopologyChange 1.3.6.1.4.1.207.1.4.167.118.1.4.1.6
The time (in hundredths of a second) since the TcWhile Timer for any port in this Bridge was non-zero for this spanning tree instance.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

dot1sMstiTopChanges 1.3.6.1.4.1.207.1.4.167.118.1.4.1.7
The number of times that there have been atleast one non-zero TcWhile Timer on this Bridge for this spanning tree instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sMstiNewRootBridgeCount 1.3.6.1.4.1.207.1.4.167.118.1.4.1.8
The number of times this Bridge has detected a Root Bridge change for this spanning tree instance. A Trap is generated on the occurence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sMstiBridgeRoleSelectionSemState 1.3.6.1.4.1.207.1.4.167.118.1.4.1.9
Current state of the Port Role Selection State Machine for this spanning tree instance for this bridge.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initbridge(0), roleselection(1)  

dot1sInstanceUpCount 1.3.6.1.4.1.207.1.4.167.118.1.4.1.10
The number of times a new spanning tree instance has been created. A Trap is generated on the occurence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sInstanceDownCount 1.3.6.1.4.1.207.1.4.167.118.1.4.1.11
The number of times a spanning tree instance has been deleted. A Trap is generated on the occurence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sOldDesignatedRoot 1.3.6.1.4.1.207.1.4.167.118.1.4.1.12
The bridge identifier of the old root of the spanning tree instance as determined by the Spanning Tree Protocol as executed by this node.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1sVlanInstanceMappingTable 1.3.6.1.4.1.207.1.4.167.118.1.5
This table contains one entry for each instance of MSTP. This table maintains context ID as one more index to support Multiple Instances.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1sVlanInstanceMappingEntry

dot1sVlanInstanceMappingEntry 1.3.6.1.4.1.207.1.4.167.118.1.5.1
A conceptual row containing the status of the MSTP instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1sVlanInstanceMappingEntry  

dot1sInstanceIndex 1.3.6.1.4.1.207.1.4.167.118.1.5.1.1
An arbitrary integer within the range from 1 to the value of Max Instance Number that uniquely identifies an instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..64  

dot1sMapVlanIndex 1.3.6.1.4.1.207.1.4.167.118.1.5.1.2
The VlanId will get mapped to the spanning tree instance specified. All the Instance Specific information for the Member ports of the Vlan will be created.This object is used only for SET operation.GET Operation returns null values. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

dot1sUnMapVlanIndex 1.3.6.1.4.1.207.1.4.167.118.1.5.1.3
The VlanId will get unmapped from spanning tree instance to which it it mapped. All the Instance Specific information for the Member ports of the Vlan will get released.This object is used only for SET operation.GET Operation returns null values.
Status: current Access: read-write
OBJECT-TYPE    
  VlanId  

dot1sSetVlanList 1.3.6.1.4.1.207.1.4.167.118.1.5.1.4
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

dot1sResetVlanList 1.3.6.1.4.1.207.1.4.167.118.1.5.1.5
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to unmap from this Instance. A vlan may not be unmapped from this instance if it is not already mapped to this Instance. This object is used only for SET operation.GET Operation returns null values.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

dot1sInstanceVlanMapped 1.3.6.1.4.1.207.1.4.167.118.1.5.1.6
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

dot1sInstanceVlanMapped2k 1.3.6.1.4.1.207.1.4.167.118.1.5.1.7
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

dot1sInstanceVlanMapped3k 1.3.6.1.4.1.207.1.4.167.118.1.5.1.8
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

dot1sInstanceVlanMapped4k 1.3.6.1.4.1.207.1.4.167.118.1.5.1.9
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

dot1sCistPortTable 1.3.6.1.4.1.207.1.4.167.118.1.6
This table contains Common Spanning Tree Port Information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1sCistPortEntry

dot1sCistPortEntry 1.3.6.1.4.1.207.1.4.167.118.1.6.1
A list of information maintained by every port for Common Spanning tree.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1sCistPortEntry  

dot1sCistPort 1.3.6.1.4.1.207.1.4.167.118.1.6.1.1
The Port number of the port for which this entry contains spanning tree information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

dot1sCistPortPathCost 1.3.6.1.4.1.207.1.4.167.118.1.6.1.2
The contribution of this port to the path cost of paths towards the CIST Root which include this port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..200000000  

dot1sCistPortPriority 1.3.6.1.4.1.207.1.4.167.118.1.6.1.3
The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting the CistPortPriority value. The values that are set for Port Priority must be in steps of 16.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..240  

dot1sCistPortDesignatedRoot 1.3.6.1.4.1.207.1.4.167.118.1.6.1.4
The unique Bridge Identifier of the bridge recorded as the CIST Root in the configuration BPDUs transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1sCistPortDesignatedBridge 1.3.6.1.4.1.207.1.4.167.118.1.6.1.5
The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1sCistPortDesignatedPort 1.3.6.1.4.1.207.1.4.167.118.1.6.1.6
The Port identifier of the port on the Designated Bridge for this port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

dot1sCistPortAdminP2P 1.3.6.1.4.1.207.1.4.167.118.1.6.1.7
The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forceTrue(0), forceFalse(1), auto(2)  

dot1sCistPortOperP2P 1.3.6.1.4.1.207.1.4.167.118.1.6.1.8
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the dot1sCistPortAdminP2P object.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

dot1sCistPortAdminEdgeStatus 1.3.6.1.4.1.207.1.4.167.118.1.6.1.9
The administrative value of the Edge Port parameter. A value of TRUE(1) indicates that this port should be assumed as an edge-port and a value of FALSE(2) indicates that this port should be assumed as a non-edge-port.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1sCistPortOperEdgeStatus 1.3.6.1.4.1.207.1.4.167.118.1.6.1.10
The operational value of the Edge Port parameter. The object is initialized to the value of dot1sCistPortAdminEdgeStatus and is set FALSE on reception of a BPDU.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

dot1sCistPortProtocolMigration 1.3.6.1.4.1.207.1.4.167.118.1.6.1.11
Indicates the Protocol migration state of this Port. When operating in RSTP/MSTP (version >= 2) mode, writing TRUE(1) to this object forces this port to transmit MSTP BPDUs without instance information. Any other operation on this object has no effect and it always returns FALSE(2) when read.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1sCistPortState 1.3.6.1.4.1.207.1.4.167.118.1.6.1.12
Current state of the Port as defined by the Common spanning tree protocol.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), discarding(2), learning(4), forwarding(5)  

dot1sCistForcePortState 1.3.6.1.4.1.207.1.4.167.118.1.6.1.13
Current state of the Port which can be changed to either Disabled or Enabled for ALL spanning tree instances. Setting this object will override the port's status in any of the MSTI contexts
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dot1sCistPortForwardTransitions 1.3.6.1.4.1.207.1.4.167.118.1.6.1.14
Number of times this port has transitioned to the Forwarding State.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortRxMstBpduCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.15
Number of MST BPDUs received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortRxRstBpduCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.16
Number of RST BPDUs received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortRxConfigBpduCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.17
Number of Configuration BPDUs received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortRxTcnBpduCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.18
Number of TCN BPDUs received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortTxMstBpduCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.19
Number of MST BPDUs Transmitted from this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortTxRstBpduCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.20
Number of RST BPDUs Transmitted from this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortTxConfigBpduCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.21
Number of Configuration BPDUs Transmitted from this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortTxTcnBpduCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.22
Number of TCN BPDUs Transmitted from this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortInvalidMstBpduRxCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.23
Number of Invalid MST BPDUs Received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortInvalidRstBpduRxCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.24
Number of Invalid RST BPDUs Received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortInvalidConfigBpduRxCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.25
Number of Invalid Configuration BPDUs Received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortInvalidTcnBpduRxCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.26
Number of Invalid TCN BPDUs Received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortTransmitSemState 1.3.6.1.4.1.207.1.4.167.118.1.6.1.27
Indicates current State of the Port Transmit state machine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER transmitinit(0), transmitperiodic(1), transmitconfig(2), transmittcn(3), transmitrstp(4), idle(5)  

dot1sCistPortReceiveSemState 1.3.6.1.4.1.207.1.4.167.118.1.6.1.28
Indicates current State of the Port Receive state machine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discard(0), receive(1)  

dot1sCistPortProtMigrationSemState 1.3.6.1.4.1.207.1.4.167.118.1.6.1.29
Indicates current State of the Port Protocol Migration State machine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER init(0), sendrstp(1), sendingrstp(2), sendstp(3), sendingstp(4)  

dot1sCistProtocolMigrationCount 1.3.6.1.4.1.207.1.4.167.118.1.6.1.30
The number of times this Port has migrated from one STP protocol version to another. The relevant protocols are STP-COMPATIBLE and RSTP/MSTP. A Trap is generated on the occurence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sCistPortDesignatedCost 1.3.6.1.4.1.207.1.4.167.118.1.6.1.31
The path cost of the Designated Port of the segment connected to this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sCistPortRegionalRoot 1.3.6.1.4.1.207.1.4.167.118.1.6.1.32
The unique Bridge Identifier of the bridge recorded as the CIST Regional Root Identifier in the configuration BPDUs transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1sCistPortRegionalPathCost 1.3.6.1.4.1.207.1.4.167.118.1.6.1.33
The contribution of this port to the path cost of paths towards the CIST Regional Root which include this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sCistSelectedPortRole 1.3.6.1.4.1.207.1.4.167.118.1.6.1.34
Selected Port Role of the port for this spanning tree instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), alternate(1), backup(2), root(3), designated(4)  

dot1sCistCurrentPortRole 1.3.6.1.4.1.207.1.4.167.118.1.6.1.35
Current Port Role of the port for this spanning tree instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), alternate(1), backup(2), root(3), designated(4)  

dot1sCistPortInfoSemState 1.3.6.1.4.1.207.1.4.167.118.1.6.1.36
Current state of the Port Information State Machine for this port in this spanning tree context.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), aged(1), update(2), superiordesg(3), repeatdesg(4), inferiordesg(5), notdesg(6), current(7), receive(8), other(9)  

dot1sCistPortRoleTransitionSemState 1.3.6.1.4.1.207.1.4.167.118.1.6.1.37
Current state of the Port Role Transition State Machine for this port in this spanning tree context.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER init(0), disableport(1), disabledport(2), rootport(3), designatedport(4), alternateport(5), masterport(6)  

dot1sCistPortStateTransitionSemState 1.3.6.1.4.1.207.1.4.167.118.1.6.1.38
Current state of the Port State Transition State Machine for this port in this spanning tree context.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discarding(0), learning(1), forwarding(2)  

dot1sCistPortTopologyChangeSemState 1.3.6.1.4.1.207.1.4.167.118.1.6.1.39
Current state of the Topology Change State Machine for this port in this spanning tree context.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), learning(1), detected(2), active(3), notifiedtcn(4), notifiedtc(5), propagating(6), acknowledged(7)  

dot1sCistPortHelloTime 1.3.6.1.4.1.207.1.4.167.118.1.6.1.40
The amount of time between the transmission of Configuration bridge PDUs by this node on this port in units of hundredths of a second.
Status: current Access: read-write
OBJECT-TYPE    
  Timeout 100..200  

dot1sCistPortOperVersion 1.3.6.1.4.1.207.1.4.167.118.1.6.1.41
This indicates whether the Port is operationally in the Mstp mode, Rstp mode or the Stp-compatible mode i.e., whether the Port is transmitting MST BPDUs, RST BPDUs or Config/TCN BPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER stpCompatible(0), rstp(2), mstp(3)  

dot1sCistPortEffectivePortState 1.3.6.1.4.1.207.1.4.167.118.1.6.1.42
The effective operational state of the port for CIST. This will TRUE only when the port is operationally up in the Interface level and Protocol level for CIST. This is will be set to False for all other times.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

dot1sCistPortAutoEdgeStatus 1.3.6.1.4.1.207.1.4.167.118.1.6.1.43
This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1sCistPortRestrictedRole 1.3.6.1.4.1.207.1.4.167.118.1.6.1.44
A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1sCistPortRestrictedTCN 1.3.6.1.4.1.207.1.4.167.118.1.6.1.45
A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC_Operational for the attached LANs transitions frequently.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1sMstiPortTable 1.3.6.1.4.1.207.1.4.167.118.1.7
This table contains Spanning Tree Instance Specific Port Information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1sMstiPortEntry

dot1sMstiPortEntry 1.3.6.1.4.1.207.1.4.167.118.1.7.1
A list of information maintained by every port for each and every spanning tree instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1sMstiPortEntry  

dot1sMstiPort 1.3.6.1.4.1.207.1.4.167.118.1.7.1.1
The Port number of the port for which this entry contains spanning tree information.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..65535  

dot1sMstiPortPathCost 1.3.6.1.4.1.207.1.4.167.118.1.7.1.2
The contribution of this port to the path cost of paths towards the MSTI Root which include this port.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..200000000  

dot1sMstiPortPriority 1.3.6.1.4.1.207.1.4.167.118.1.7.1.3
The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..240  

dot1sMstiPortDesignatedRoot 1.3.6.1.4.1.207.1.4.167.118.1.7.1.4
The unique Bridge Identifier of the bridge recorded as the MSTI Regional Root in the configuration BPDUs transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1sMstiPortDesignatedBridge 1.3.6.1.4.1.207.1.4.167.118.1.7.1.5
The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1sMstiPortDesignatedPort 1.3.6.1.4.1.207.1.4.167.118.1.7.1.6
The Port identifier of the port on the Designated Bridge for this port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

dot1sMstiPortState 1.3.6.1.4.1.207.1.4.167.118.1.7.1.7
Current state of the Port as defined by the Multiple spanning tree protocol. Port which is Forwarding state in one instance can be in Discarding (Blocking) state in another instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), discarding(2), learning(4), forwarding(5)  

dot1sMstiForcePortState 1.3.6.1.4.1.207.1.4.167.118.1.7.1.8
Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'dot1sCistForcePortState' is set to 'enabled' for this port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dot1sMstiPortForwardTransitions 1.3.6.1.4.1.207.1.4.167.118.1.7.1.9
Number of times this port has transitioned to the Forwarding State for specific instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sMstiPortReceivedBPDUs 1.3.6.1.4.1.207.1.4.167.118.1.7.1.10
Number of BPDUs received by this port for this spanning tree instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sMstiPortTransmittedBPDUs 1.3.6.1.4.1.207.1.4.167.118.1.7.1.11
Number of BPDUs transmitted on this port for this spanning tree instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sMstiPortInvalidBPDUsRcvd 1.3.6.1.4.1.207.1.4.167.118.1.7.1.12
Number of Invalid BPDUs received on this Port for this spanning tree instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1sMstiPortDesignatedCost 1.3.6.1.4.1.207.1.4.167.118.1.7.1.13
The path cost of the Designated Port of the segment connected to this port.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sMstiSelectedPortRole 1.3.6.1.4.1.207.1.4.167.118.1.7.1.14
Selected Port Role of the port for this spanning tree instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), alternate(1), backup(2), root(3), designated(4), master(5)  

dot1sMstiCurrentPortRole 1.3.6.1.4.1.207.1.4.167.118.1.7.1.15
Current Port Role of the port for this spanning tree instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), alternate(1), backup(2), root(3), designated(4), master(5)  

dot1sMstiPortInfoSemState 1.3.6.1.4.1.207.1.4.167.118.1.7.1.16
Current state of the Port Information State Machine for this port in this spanning tree context.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), aged(1), update(2), superiordesg(3), repeatdesg(4), inferiordesg(5), notdesg(6), current(7), receive(8), other(9)  

dot1sMstiPortRoleTransitionSemState 1.3.6.1.4.1.207.1.4.167.118.1.7.1.17
Current state of the Port Role Transition State Machine for this port in this spanning tree context.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER init(0), disableport(1), disabledport(2), rootport(3), designatedport(4), alternateport(5), masterport(6)  

dot1sMstiPortStateTransitionSemState 1.3.6.1.4.1.207.1.4.167.118.1.7.1.18
Current state of the Port State Transition State Machine for this port in this spanning tree context.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discarding(0), learning(1), forwarding(2)  

dot1sMstiPortTopologyChangeSemState 1.3.6.1.4.1.207.1.4.167.118.1.7.1.19
Current state of the Topology Change State Machine for this port in this spanning tree context.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), learning(1), detected(2), active(3), notifiedtcn(4), notifiedtc(5), propagating(6), acknowledged(7)  

dot1sMstiPortEffectivePortState 1.3.6.1.4.1.207.1.4.167.118.1.7.1.20
The effective operational stae of the port for specific instance. This is will be TRUE only when the port is operationally up in the interface level and Protocol level for the specific instance. This is will be set to false at all other times.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

dot1sMstSetGlobalTrapOption 1.3.6.1.4.1.207.1.4.167.118.2.1
This object is used to enable and disable MSTP traps for memory failure or buffer failure irrespective of the context in which the failure occurs. 0 - Traps are not enabled. 1 - Memory and buffer failure traps enabled
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1  

dot1sGlobalErrTrapType 1.3.6.1.4.1.207.1.4.167.118.2.2
Used within the Trap Notification PDU. It returns the following values none - none of the below values memfail - memory allocation failure bufffail - buffer allocation failure
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), memfail(1), bufffail(2)  

dot1sMstTrapsControlTable 1.3.6.1.4.1.207.1.4.167.118.2.3
List of per virtual bridge Trap Control Info.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1sMstTrapsControlEntry

dot1sMstTrapsControlEntry 1.3.6.1.4.1.207.1.4.167.118.2.3.1
Virtual bridge TrapsControl information.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1sMstTrapsControlEntry  

dot1sSetTraps 1.3.6.1.4.1.207.1.4.167.118.2.3.1.1
This object is used to enable and disable context-specific MSTP traps. Currently the following are defined 0 - Traps are not enabled. 1 - General Traps like protocol up or down 2 - Exception Traps like port protocol migration or invalid packet rcvd in port 3 - All the above Traps
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..3  

dot1sGenTrapType 1.3.6.1.4.1.207.1.4.167.118.2.3.1.2
Used within the Trap Notification PDU. It denotes general events like none - none of the below values up - protocol UP, down - protocol DOWN
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), up(1), down(2)  

dot1sPortTrapNotificationTable 1.3.6.1.4.1.207.1.4.167.118.2.4
This table is used to store the notification information occured in each of the port for protocol migration and invalid packet received. This table is maintained per virtual context in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1sPortTrapNotificationEntry

dot1sPortTrapNotificationEntry 1.3.6.1.4.1.207.1.4.167.118.2.4.1
This entry is used to store the notification information
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1sPortTrapNotificationEntry  

dot1sPortTrapIndex 1.3.6.1.4.1.207.1.4.167.118.2.4.1.1
A unique value, greater than zero, indicating the Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4096  

dot1sPortMigrationType 1.3.6.1.4.1.207.1.4.167.118.2.4.1.2
Port Protocol migration type occured in the port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sendstp(0), sendrstp(1)  

dot1sPktErrType 1.3.6.1.4.1.207.1.4.167.118.2.4.1.3
Type of invalid packet received in each of the port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER protocolIdErr(0), invalidBpdu(1), configLengthErr(2), tcnLengthErr(3), rstpLengthErr(4), maxAgeErr(5), fwdDelayErr(6), helloTimeErr(7), mstpLengthErr(8)  

dot1sPktErrVal 1.3.6.1.4.1.207.1.4.167.118.2.4.1.4
Packet error value corresponding to the above type
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1sPortRoleTrapNotificationTable 1.3.6.1.4.1.207.1.4.167.118.2.5
This table is used to store the notification information occured in each of the port for its role change. This table is maintained per virtual context in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1sPortRoleTrapNotificationEntry

dot1sPortRoleTrapNotificationEntry 1.3.6.1.4.1.207.1.4.167.118.2.5.1
This entry is used to store the notification information
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1sPortRoleTrapNotificationEntry  

dot1sPortRoleType 1.3.6.1.4.1.207.1.4.167.118.2.5.1.1
Particular Role Selected for the Port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabledPort(0), alternatePort(1), backupPort(2), rootPort(3), designatedPort(4), masterport(5)  

dot1sOldRoleType 1.3.6.1.4.1.207.1.4.167.118.2.5.1.2
Particular Role which is existing for the Port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabledPort(0), alternatePort(1), backupPort(2), rootPort(3), designatedPort(4), masterport(5)  

dot1sTraps 1.3.6.1.4.1.207.1.4.167.118.3.0
OBJECT IDENTIFIER    

dot1sGlobalErrTrap 1.3.6.1.4.1.207.1.4.167.118.3.0.1
Generated when any of the error events like memory failure or buffer failure or protocol migration or new root or topology change occurs
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1sGenTrap 1.3.6.1.4.1.207.1.4.167.118.3.0.2
Generated when any of the general events like protocol up or protocol down occurs
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1sNewRootTrap 1.3.6.1.4.1.207.1.4.167.118.3.0.3
Generated whenever a new root bridge is selected in the topology
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1sTopologyChgTrap 1.3.6.1.4.1.207.1.4.167.118.3.0.4
Generated when topology change is detected
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1sProtocolMigrationTrap 1.3.6.1.4.1.207.1.4.167.118.3.0.5
Generated when port protocol migration happens in the port
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1sInvalidBpduRxdTrap 1.3.6.1.4.1.207.1.4.167.118.3.0.6
Generated when the invalid packet is received for bpdu/stp/rstp/maximum age/forward delay/hello time
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1sRegionConfigChangeTrap 1.3.6.1.4.1.207.1.4.167.118.3.0.7
Generated when the MST region's configuration identifier changes.
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1sNewPortRoleTrap 1.3.6.1.4.1.207.1.4.167.118.3.0.8
Generated whenever a new role is selected for the port
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1wRst 1.3.6.1.4.1.207.1.4.167.119.1
OBJECT IDENTIFIER    

dot1wRstTrapsControl 1.3.6.1.4.1.207.1.4.167.119.2
OBJECT IDENTIFIER    

dot1wRstTraps 1.3.6.1.4.1.207.1.4.167.119.3
OBJECT IDENTIFIER    

dot1wRstTable 1.3.6.1.4.1.207.1.4.167.119.1.3
List of per virtual context RstModule Parameters
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1wRstEntry

dot1wRstEntry 1.3.6.1.4.1.207.1.4.167.119.1.3.1
Virtual Bridge RstModule Parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1wRstEntry  

dot1wRstContextId 1.3.6.1.4.1.207.1.4.167.119.1.3.1.1
Identifies the Virtual Bridge Context.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

dot1wSystemControl 1.3.6.1.4.1.207.1.4.167.119.1.3.1.2
The administrative system control status requested by management for the RSTP feature. The value 'start'(1) indicates that all resources required by RSTP should be allocated and RSTP should be supported in the device on all ports. The value shutdown(2) indicates that RSTP should be shutdown in the device on all ports and all allocated memory must be released.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER start(1), shutdown(2)  

dot1wModuleStatus 1.3.6.1.4.1.207.1.4.167.119.1.3.1.3
The administrative module status requested by management for the RSTP Module. This enables or disables RSTP in the system. A value of 'enabled' (1) indicates that RSTP must be enabled in the device on all the ports. A value of 'disabled'(2) indicates that RSTP must be disabled in the device on all the ports. This object can be set only after the object dot1wSystemControl has been set.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

dot1wTraceOption 1.3.6.1.4.1.207.1.4.167.119.1.3.1.4
This object is used to enable Trace Statements in the RSTP Module. A FOUR BYTE integer is used for enabling the level of tracing. Each BIT in the four byte integer, represents a particular level of Trace. The mapping between the bit positions & the level of trace is as follows: 0 - Init and Shutdown Traces 1 - Management Traces 2 - Data Path Traces 3 - Control Plane Traces 4 - Packet Dump Traces 5 - Traces related to All Resources except Buffers 6 - All Failure Traces 7 - Buffer Traces The remaining bits are unused. Combination of trace levels are also allowed. For example if the bits 0 and 1 are set, then the Trace statements related to Init-Shutdown and management will be printed. The user has to enter the corresponding INTEGER VALUE for the bits set. For example if bits 0 and 1 are to be set then user has to give the value for this object as 3. Setting the Trace Option to any value will cause the Debug Option to be set to 0 (i.e.) the Trace Option and Debug Option are mutually exclusive.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..255  

dot1wDebugOption 1.3.6.1.4.1.207.1.4.167.119.1.3.1.5
This object is used to enable Debug Statements in the RSTP Module. A FOUR BYTE integer is used for enabling the level of debugging. Each BIT in the four byte integer, represents a particular level of Debug. The mapping between the bit positions & the level of debug is as follows: 0 - Init and Shutdown Debug statements 1 - Management Debug statements 2 - Memory related Debug statements 3 - BPDU related Debug statements 4 - Event Handling Debug statements 5 - Timer Module Debug statements 6 - Port Information SEM Debug statements 7 - Port Receive SEM Debug statements 8 - Role Selection SEM Debug statements 9 - Role Transition SEM Debug statements 10 - State Transition SEM Debug statements 11 - Protocol Migration SEM Debug statements 12 - Topology Change SEM Debug statements 13 - Port Transmit SEM Debug statements 14 - Bridge Detection SEM Debug statements 15 - All Failure Debug statements 16 - Redundancy code flow Debug statements 17 - State Machine variable changes debug statements The remaining bits are unused. Combination of debug levels are also allowed. For example if the bits 0 and 1 are set, then the Debug statements related to Init-Shutdown and management will be printed. The user has to enter the corresponding INTEGER VALUE for the bits set. For example if bits 0 and 1 are to be set then user has to give the value for this object as 3. Setting the Debug Option to any value will cause the Trace Option to be set to 0 (i.e.) the Trace Option and Debug Option are mutually exclusive.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..262143  

dot1wRstpUpCount 1.3.6.1.4.1.207.1.4.167.119.1.3.1.6
The number of times RSTP Module has been enabled.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wRstpDownCount 1.3.6.1.4.1.207.1.4.167.119.1.3.1.7
The number of times RSTP Module has been disabled.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wBufferFailureCount 1.3.6.1.4.1.207.1.4.167.119.1.3.1.8
The number of times buffer overflows/failures have occurred. A Trap is generated on the occurrence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wMemAllocFailureCount 1.3.6.1.4.1.207.1.4.167.119.1.3.1.9
The number of times memory allocation failures have occurred. A Trap is generated on the occurrence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wNewRootIdCount 1.3.6.1.4.1.207.1.4.167.119.1.3.1.10
The number of times this Bridge has detected a new Root in the topology. A Trap is generated on the occurrence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortRoleSelSmState 1.3.6.1.4.1.207.1.4.167.119.1.3.1.11
This indicates the current state of the Port Role Selection State Machine. This object will hold the value 'initbridge' when the Port Role Selection state machine is in the INIT_BRIDGE state and the value of 'roleselection' when the state machine is in the ROLE_SELECTION state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initbridge(0), roleselection(1)  

dot1wOldDesignatedRoot 1.3.6.1.4.1.207.1.4.167.119.1.3.1.12
The bridge identifier of the old root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

dot1wDynamicPathcostCalculation 1.3.6.1.4.1.207.1.4.167.119.1.3.1.13
This object is used to determine whether dynamic pathcost calculation is allowed or not.The value is determined by management. If set to true, pathcost is calculated dynamically from port speed, otherwise the link speed at the time of port creation is used for calculating the path cost. In both cases if the user has configured a pathcost for the port that will be used. By default dynamic pathcost calculation is set to false.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1wContextName 1.3.6.1.4.1.207.1.4.167.119.1.3.1.14
This object is used to identity the context-name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

dot1wPortExtTable 1.3.6.1.4.1.207.1.4.167.119.1.4
This is a table that is an extension to the dot1dStpExtPortTable. This contains object(s) that are Port-based.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1wPortExtEntry

dot1wPortExtEntry 1.3.6.1.4.1.207.1.4.167.119.1.4.1
Each entry in this table is for each port present in the system. This table is indexed by the dot1wPort.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1wPortExtEntry  

dot1wPort 1.3.6.1.4.1.207.1.4.167.119.1.4.1.1
A unique value, greater than zero, indicating the Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4096  

dot1wPortRole 1.3.6.1.4.1.207.1.4.167.119.1.4.1.2
This indicates the current Port Role assumed by this Port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabledPort(0), alternatePort(1), backupPort(2), rootPort(3), designatedPort(4)  

dot1wPortOperVersion 1.3.6.1.4.1.207.1.4.167.119.1.4.1.3
This indicates whether the Port is operationally in the Rstp mode or the Stp-compatible mode i.e., whether the Port is transmitting RST BPDUs or Config/TCN BPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER stpCompatible(0), rstp(2)  

dot1wPortInfoSmState 1.3.6.1.4.1.207.1.4.167.119.1.4.1.4
This indicates the current state of the Port Information state machine. This object will hold the value 'disabled' when the Port Information state machine is in the DISABLED state, the value 'aged' when the state machine is in the AGED state, the value 'update' when the state machine is in the UPDATE state, the value 'superior' when the state machine is in the SUPERIOR state, the value 'repeat' when the state machine is in the REPEAT state, the value 'notdesignated' when the state machine is in the NOT_DESIGNATED state, the value 'present' when the state machine is in the CURRENT state and the value 'receive' when the state machine is in the RECEIVE state and the value 'inferiordesignated' when the state machine is in the INFERIOR_DESIGNATED state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), aged(1), update(2), superior(3), repeat(4), notdesignated(5), present(6), receive(7), inferiordesignated(8)  

dot1wPortMigSmState 1.3.6.1.4.1.207.1.4.167.119.1.4.1.5
This indicates the current state of the Port Protocol Migration state machine. This object will hold the value 'checkingrstp' when the Protocol Migration state machine is in the CHECKING_RSTP state, the value 'selectingstp' when the state machine is in the SELECTING_STP state, the value 'sensing' when the state machine is in the SENSING state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER checkingrstp(0), selectingstp(1), sensing(2)  

dot1wPortRoleTransSmState 1.3.6.1.4.1.207.1.4.167.119.1.4.1.6
This indicates the current state of the Port Role Transition state machine. This object will hold the value 'init' when the Port Role Transition state machine is in the INIT state, the value 'disableport' when the state machine is in the DISABLE_PORT state, the value 'disabledport' when the state machine is in the DISABLED_PORT state, the value 'rootport' when the state machine is in the ROOT_PORT state, the value 'desgport' when the state machine is in the DESIGNATED_PORT state, the value 'backupport' when the state machine is in BACKUP_PORT state, the value 'rootproposed' when the state machine is in the ROOT_PROPOSED state, the value 'rootagreed' when the state machine is in the ROOT_AGREED state, the value 'reroot' when the state machine is in the REROOT state, the value 'rootforward' when the state machine is in the ROOT_FORWARD state, the value 'rootlearn' when the state machine is in the ROOT_LEARN state, the value 'rerooted' when the state machine is in the REROOTED state, the value 'designatedpropose' when the state machine is in the DESIGNATED_PROPOSE state, the value 'designatedsynced' when the state machine is in the DESIGNATED_SYNCED state, the value 'designatedretired' when the state machine is in the DESIGNATED_RETIRED state, the value 'designatedforward' when the state machine is in the DESIGNATED_FORWARD state, the value 'designatedlearn' when the state machine is in the DESIGNATED_LEARN state and the value 'designatedlisten' when the state machine is in the DESIGNATED_LISTEN state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER init(0), disableport(1), disabledport(2), rootport(3), designatedport(4), backupport(5), rootproposed(6), rootagreed(7), reroot(8), rootforward(9), rootlearn(10), rerooted(11), designatedpropose(12), designatedsynced(13), designatedretired(14), designatedforward(15), designatedlearn(16), designatedlisten(17)  

dot1wPortStateTransSmState 1.3.6.1.4.1.207.1.4.167.119.1.4.1.7
This indicates the current state of the Port State Transition state machine. This object will hold the value 'discarding' when the Port State Transition state machine is in the DISCARDING state, the value 'learning' when the state machine is in the LEARNING state and the value 'forwarding' when the state machine is in the FORWARDING state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discarding(0), learning(1), forwarding(2)  

dot1wPortTopoChSmState 1.3.6.1.4.1.207.1.4.167.119.1.4.1.8
This indicates the current state of the Topology Change state machine. This object will hold the value 'inactive' when the Topology Change state machine is in the INACTIVE state, the value 'learning' when the state machine is in the LEARNING state, the value 'active' when the state machine is in the ACTIVE state, the value 'detected' when the state machine is in the DETECTED state, the value 'notifiedtcn' when the state machine is in the NOTIFIED_TCN state, the value 'notifiedtc' when the state machine is in the NOTIFIED_TC state, the value 'propagating' state when the state machine is in the PROPAGATING state and the value 'acknowledged' when the state machine is in the ACKNOWLEDGED state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(0), learning(1), detected(2), active(3), notifiedtcn(4), notifiedtc(5), propagating(6), acknowledged(7)  

dot1wPortTxSmState 1.3.6.1.4.1.207.1.4.167.119.1.4.1.9
This indicates the current state of the Port Transmit state machine. This object will hold the value 'transmitinit' when the Port Transmit state machine is in the TRANSMIT_INIT state, the value 'transmitperiodic' when the state machine is in the TRANSMIT_PERIODIC state, the value 'transmitconfig' when the state machine is in the TRANSMIT_CONFIG state, the value 'transmittcn', when the state machine is in the TRANSMIT_TCN state, the value 'transmitrstp', when the state machine is in the TRANSMIT_RSTP state and the value 'idle' when the state machine is in the IDLE state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER transmitinit(0), transmitperiodic(1), transmitconfig(2), transmittcn(3), transmitrstp(4), idle(5)  

dot1wPortRxRstBpduCount 1.3.6.1.4.1.207.1.4.167.119.1.4.1.10
The number of RST BPDUs that have been received on this Port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortRxConfigBpduCount 1.3.6.1.4.1.207.1.4.167.119.1.4.1.11
The number of Config BPDUs that have been received on this Port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortRxTcnBpduCount 1.3.6.1.4.1.207.1.4.167.119.1.4.1.12
The number of TCN BPDUs that have been received on this Port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortTxRstBpduCount 1.3.6.1.4.1.207.1.4.167.119.1.4.1.13
The number of RST BPDUs that have been transmitted by this Port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortTxConfigBpduCount 1.3.6.1.4.1.207.1.4.167.119.1.4.1.14
The number of Config BPDUs that have been transmitted by this Port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortTxTcnBpduCount 1.3.6.1.4.1.207.1.4.167.119.1.4.1.15
The number of TCN BPDUs that have been transmitted by this Port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortInvalidRstBpduRxCount 1.3.6.1.4.1.207.1.4.167.119.1.4.1.16
The number of invalid RSTP BPDUs that have been received on this Port. A Trap is generated on the occurrence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortInvalidConfigBpduRxCount 1.3.6.1.4.1.207.1.4.167.119.1.4.1.17
The number of invalid Configuration BPDUs that have been received on this Port. A Trap is generated on the occurrence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortInvalidTcnBpduRxCount 1.3.6.1.4.1.207.1.4.167.119.1.4.1.18
The number of invalid TCN BPDUs that have been received on this Port. A Trap is generated on the occurrence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortProtocolMigrationCount 1.3.6.1.4.1.207.1.4.167.119.1.4.1.19
The number of times this Port has migrated from one STP protocol version to another. The relevant protocols are STP-COMPATIBLE and RSTP. A Trap is generated on the occurrence of this event.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dot1wPortEffectivePortState 1.3.6.1.4.1.207.1.4.167.119.1.4.1.20
The effective Operational state of the port. This object will be set to TRUE only when the port is operationally up in the interface manager and the force Port State for this port and specified port state is enabled. Otherwise this object is set to FALSE.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

dot1wPortAutoEdge 1.3.6.1.4.1.207.1.4.167.119.1.4.1.21
This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1wPortRestrictedRole 1.3.6.1.4.1.207.1.4.167.119.1.4.1.22
A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1wPortRestrictedTCN 1.3.6.1.4.1.207.1.4.167.119.1.4.1.23
A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC_Operational for the attached LANs transitions frequently.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1wSetGlobalTraps 1.3.6.1.4.1.207.1.4.167.119.2.1
This object is used to enable and disable RSTP traps for memory failure or buffer failure irrespective of the context in which the failure occurs. 0 - Traps are not enabled. 1 - Memory and buffer failure traps enabled
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1  

dot1wGlobalErrTrapType 1.3.6.1.4.1.207.1.4.167.119.2.2
Used within the Trap Notification PDU. It returns the following values none - none of the below values memfail - memory allocation failure bufffail - buffer allocation failure
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), memfail(1), bufffail(2)  

dot1wRstTrapsControlTable 1.3.6.1.4.1.207.1.4.167.119.2.3
List of per virtual bridge TrapsControl Info.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1wRstTrapsControlEntry

dot1wRstTrapsControlEntry 1.3.6.1.4.1.207.1.4.167.119.2.3.1
Virtual bridge TrapsControl information.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1wRstTrapsControlEntry  

dot1wSetTraps 1.3.6.1.4.1.207.1.4.167.119.2.3.1.1
This object is used to enable and disable context-specific RSTP traps. Currently the following are defined 0 - Traps are not enabled. 1 - Protocol up or down traps. 2 - Exception Traps like port protocol migration or invalid packet rcvd in port 3 - All the above Traps
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..3  

dot1wGenTrapType 1.3.6.1.4.1.207.1.4.167.119.2.3.1.2
Used within the Trap Notification PDU. It denotes general events like none - none of the below values up - protocol UP, down - protocol DOWN
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), up(1), down(2)  

dot1wPortTrapNotificationTable 1.3.6.1.4.1.207.1.4.167.119.2.4
This table is used to store the notification information occurred in each of the port for protocol migration and invalid packet received
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1wPortTrapNotificationEntry

dot1wPortTrapNotificationEntry 1.3.6.1.4.1.207.1.4.167.119.2.4.1
This entry is used to store the notification information
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1wPortTrapNotificationEntry  

dot1wPortTrapIndex 1.3.6.1.4.1.207.1.4.167.119.2.4.1.1
A unique value, greater than zero, indicating the Port number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..4096  

dot1wPortMigrationType 1.3.6.1.4.1.207.1.4.167.119.2.4.1.2
Port Protocol migration type occurred in the port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER sendstp(0), sendrstp(1)  

dot1wPktErrType 1.3.6.1.4.1.207.1.4.167.119.2.4.1.3
Type of invalid packet received in each of the port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER protocolIdErr(0), invalidBpdu(1), configLengthErr(2), tcnLengthErr(3), rstpLengthErr(4), maxAgeErr(5), fwdDelayErr(6), helloTimeErr(7)  

dot1wPktErrVal 1.3.6.1.4.1.207.1.4.167.119.2.4.1.4
Packet error value corresponding to the above type
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

dot1wPortRoleType 1.3.6.1.4.1.207.1.4.167.119.2.4.1.5
Particular Role Selected for the Port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabledPort(0), alternatePort(1), backupPort(2), rootPort(3), designatedPort(4)  

dot1wOldRoleType 1.3.6.1.4.1.207.1.4.167.119.2.4.1.6
Particular Role which is existing for the Port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabledPort(0), alternatePort(1), backupPort(2), rootPort(3), designatedPort(4)  

dot1wTraps 1.3.6.1.4.1.207.1.4.167.119.3.0
OBJECT IDENTIFIER    

dot1wGlobalErrTrap 1.3.6.1.4.1.207.1.4.167.119.3.0.1
Generated when any of the error events like memory failure or buffer failure or protocol migration or new root or topology change occurrs
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1wGenTrap 1.3.6.1.4.1.207.1.4.167.119.3.0.2
Generated when any of the general events like protocol up or protocol down occurrs
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1wNewRootTrap 1.3.6.1.4.1.207.1.4.167.119.3.0.3
Generated whenever a new root bridge is selected in the topology
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1wTopologyChgTrap 1.3.6.1.4.1.207.1.4.167.119.3.0.4
Generated when topology change is detected
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1wProtocolMigrationTrap 1.3.6.1.4.1.207.1.4.167.119.3.0.5
Generated when port protocol migration happens in the port
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1wInvalidBpduRxdTrap 1.3.6.1.4.1.207.1.4.167.119.3.0.6
Generated when the invalid packet is received for bpdu/stp/rstp/maximum age/forward delay/hello time
Status: current Access: read-only
NOTIFICATION-TYPE    

dot1wNewPortRoleTrap 1.3.6.1.4.1.207.1.4.167.119.3.0.7
Generated whenever a new role is selected for the port
Status: current Access: read-only
NOTIFICATION-TYPE    

l2Dot1qVlan 1.3.6.1.4.1.207.1.4.167.120.1
OBJECT IDENTIFIER    

portBaseVlan 1.3.6.1.4.1.207.1.4.167.120.3
OBJECT IDENTIFIER    

portBaseStatic 1.3.6.1.4.1.207.1.4.167.120.4
OBJECT IDENTIFIER    

dot1qVlanGlobalTrace 1.3.6.1.4.1.207.1.4.167.120.1.1
Enable/Disable the global trace in VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1qVlanGlobalsTable 1.3.6.1.4.1.207.1.4.167.120.1.2
List of per virtual context Vlan Module Parameters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDot1qVlanGlobalsEntry

dot1qVlanGlobalsEntry 1.3.6.1.4.1.207.1.4.167.120.1.2.1
Per virtual context Vlan module parmaters.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDot1qVlanGlobalsEntry  

dot1qVlanGlobalsContextId 1.3.6.1.4.1.207.1.4.167.120.1.2.1.1
Identifies the virtual context in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

dot1qGarpShutdownStatus 1.3.6.1.4.1.207.1.4.167.120.1.2.1.6
The administrative status requested by management for GARP The value true(1) indicates that GARP should be shutdown in the device on all ports. All memory will be released. The value false(2) indicates that GARP should be active in the device on all ports. This object can be set to true only when none of the Garp applications (GVRP, GMRP) are enabled. Whenever Garp is enabled after shutdown, Gvrp and Gmrp must be enabled explicitly.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

dot1qVlanDebug 1.3.6.1.4.1.207.1.4.167.120.1.2.1.7
Enables the tracing in the selected submodule in VLAN. A 32 bit integer is used to store the Tracing level in the specified module. Different Tracing Levels - BIT 0 - Initialisation and Shutdown Trace. BIT 1 - Management trace. BIT 2 - Data path trace. BIT 3 - Control Plane trace. BIT 4 - Packet Dump. BIT 5 - OS Resource trace. BIT 6 - All Failure trace (All failures including Packet Validation) BIT 7 - Buffer Trace. Different submodule Tracing - BIT 16 - Tracing in VLAN module. BIT 17 - Tracing in VLAN Priority module. BIT 18 - Tracing in VLAN Redundancy module. The remaining bits are reserved. The combination of levels and submodules are allowed i.e. Tracing can be allowed at all failure and data path level in All submodules by setting the BIT appropriately. For Example, setting the debug value to the following bit stream, 00000000000000010000000000000100 will enable data path trace prints in VLAN module. Multiple submodules and multiple levels can be combined by setting the corresponding bits. For Example, setting the debug value to the following bit stream, 00000000000000110000000000001100 will enable data path and control plane trace prints in VLAN and VLAN Priority modules. Note : BIT0 is the least significant bit and BIT31 is the most significant bit.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..524287  

dot1qVlanLearningMode 1.3.6.1.4.1.207.1.4.167.120.1.2.1.8
The type of VLAN learning mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ivl(1), svl(2)  

dot1qVlanOperStatus 1.3.6.1.4.1.207.1.4.167.120.1.2.1.10
The operational status of the Vlan module. The value enabled(1) indicates that Vlan module is currently enabled in the device. The value disabled(2) indicates that Vlan module is currently disabled in the device.
Status: current Access: read-only
OBJECT-TYPE    
  EnabledStatus  

dot1qGvrpOperStatus 1.3.6.1.4.1.207.1.4.167.120.1.2.1.11
The operational status of the GVRP module. The value enabled(1) indicates that GVRP module is currently enabled in the device. The value disabled(2) indicates that GVRP module is currently disabled in the device.
Status: current Access: read-only
OBJECT-TYPE    
  EnabledStatus  

portBaseVlanEnablePerPort 1.3.6.1.4.1.207.1.4.167.120.3.1
The set of ports which are in port-based VLAN mode.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

portBaseVlanCurrentTable 1.3.6.1.4.1.207.1.4.167.120.3.2
A table containing current configuration information for each VLAN currently configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabPortBaseVlanCurrentEntry

tabPortBaseVlanCurrentEntry 1.3.6.1.4.1.207.1.4.167.120.3.2.1
Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabPortBaseVlanCurrentEntry  

portBaseVlanIndex 1.3.6.1.4.1.207.1.4.167.120.3.2.1.1
The VLAN-ID or other identifier referring to this VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

portBaseVlanName 1.3.6.1.4.1.207.1.4.167.120.3.2.1.2
The VLAN-Name referring to this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

portBaseVlanCurrentEgressPorts 1.3.6.1.4.1.207.1.4.167.120.3.2.1.3
The set of ports which are transmitting traffic for this VLAN as either tagged or untagged frames.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

portBaseVlanStatus 1.3.6.1.4.1.207.1.4.167.120.3.2.1.4
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. permanent(2) - this entry, corresponding to an entry in portBaseVlanStaticTable, is currently in use and will remain so after the next reset of the device. The port lists for this entry include ports from the equivalent portBaseVlanStaticTable entry and ports learnt dynamically. dynamicGvrp(3) - this entry is currently in use and will remain so until removed by GVRP. There is no static entry for this VLAN and it will be removed when the last port leaves the VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), permanent(2), dynamicGvrp(3)  

portBaseVlanCreationTime 1.3.6.1.4.1.207.1.4.167.120.3.2.1.5
The value of sysUpTime when this VLAN was created.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

portBaseVlanRowStatus 1.3.6.1.4.1.207.1.4.167.120.3.2.1.6
The status of this concsystual row. All writable objects in this row may be modified only when the row status is not active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

portBaseStaticUnicastTable 1.3.6.1.4.1.207.1.4.167.120.4.1
A table containing filtering information for Unicast MAC addresses for each Filtering Database, configured into the device by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific unicast destination addresses are allowed to be forwarded. A value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for unicast addresses only.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabPortBaseStaticUnicastEntry

tabPortBaseStaticUnicastEntry 1.3.6.1.4.1.207.1.4.167.120.4.1.1
Filtering information configured into the device by (local or network) management specifying the set of ports to which frames received from a specific port and containing a specific unicast destination address are allowed to be forwarded.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabPortBaseStaticUnicastEntry  

portBaseStaticUnicastIndex 1.3.6.1.4.1.207.1.4.167.120.4.1.1.1
The index of entries int this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

portBaseStaticUnicastVlanIndex 1.3.6.1.4.1.207.1.4.167.120.4.1.1.2
The VLAN-ID or other identifier referring to this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

portBaseStaticUnicastAddress 1.3.6.1.4.1.207.1.4.167.120.4.1.1.3
The destination MAC address in a frame to which this entry's filtering information applies. This object must take the value of a unicast address.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

portBaseStaticUnicastAllowedToGoTo 1.3.6.1.4.1.207.1.4.167.120.4.1.1.4
The set of ports for which a frame with a specific unicast address will be flooded in the event that it has not been learned. It also specifies the set of ports a specific unicast address may be dynamically learnt on. The portBaseTpFdbTable will have an equivalent entry with a portBaseTpFdbPort value of '0' until this address has been learnt, when it will be updated with the port the address has been seen on. This only applies to ports that are members of the VLAN, defined by portBaseVlanCurrentEgressPorts. The default value of this object is a string of ones of appropriate length.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

portBaseStaticUnicastStatus 1.3.6.1.4.1.207.1.4.167.120.4.1.1.5
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5)  

portBaseStaticUnicastRowStatus 1.3.6.1.4.1.207.1.4.167.120.4.1.1.6
The status of this concsystual row. All writable objects in this row may be modified only when the row status is not active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

portBaseStaticMulticastTable 1.3.6.1.4.1.207.1.4.167.120.4.2
A table containing filtering information for Multicast and Broadcast MAC addresses for each VLAN, configured into the device by (local or network) management specifying the set of ports to which frames received from specific ports and containing specific Multicast and Broadcast destination addresses are allowed to be forwarded. A value of zero in this table as the port number from which frames with a specific destination address are received, is used to specify all ports for which there is no specific entry in this table for that particular destination address. Entries are valid for Multicast and Broadcast addresses only.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabPortBaseStaticMulticastEntry

tabPortBaseStaticMulticastEntry 1.3.6.1.4.1.207.1.4.167.120.4.2.1
Filtering information configured into the device by (local or network) management specifying the set of ports to which frames received from this specific port for this VLAN and containing this Multicast or Broadcast destination address are allowed to be forwarded.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabPortBaseStaticMulticastEntry  

portBaseStaticMulticastIndex 1.3.6.1.4.1.207.1.4.167.120.4.2.1.1
The index of entries int this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..65535  

portBaseStaticMulticastVlanIndex 1.3.6.1.4.1.207.1.4.167.120.4.2.1.2
The VLAN-ID or other identifier referring to this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

portBaseStaticMulticastAddress 1.3.6.1.4.1.207.1.4.167.120.4.2.1.3
The destination MAC address in a frame to which this entry's filtering information applies. This object must take the value of a Multicast or Broadcast address.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

portBaseStaticMulticastStaticEgressPorts 1.3.6.1.4.1.207.1.4.167.120.4.2.1.4
The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in portBaseStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

portBaseStaticMulticastStatus 1.3.6.1.4.1.207.1.4.167.120.4.2.1.5
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. invalid(2) - writing this value to the object removes the corresponding entry. permanent(3) - this entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - this entry is currently in use and will remain so until the next reset of the bridge. deleteOnTimeout(5) - this entry is currently in use and will remain so until it is aged out.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), permanent(3), deleteOnReset(4), deleteOnTimeout(5)  

portBaseStaticMulticastRowStatus 1.3.6.1.4.1.207.1.4.167.120.4.2.1.6
The status of this concsystual row. All writable objects in this row may be modified only when the row status is not active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

fsLldpSystem 1.3.6.1.4.1.207.1.4.167.158.1
OBJECT IDENTIFIER    

fsLldpTLV 1.3.6.1.4.1.207.1.4.167.158.2
OBJECT IDENTIFIER    

fsLldpStatistics 1.3.6.1.4.1.207.1.4.167.158.3
OBJECT IDENTIFIER    

fsLldpNotification 1.3.6.1.4.1.207.1.4.167.158.4
OBJECT IDENTIFIER    

fsLldpSystemControl 1.3.6.1.4.1.207.1.4.167.158.1.1
The administrative system control status of LLDP module. The value 'start' (1) indicates that all resources required by LLDP module should be allocated and LLDP should be supported in the device on all ports. The value 'shutdown' (3) indicates that LLDP should be shutdown in the device on all ports and all allocated memory must be released. Here, start and shutdown are configurable values. shutdownInProgress can only be read and cannot be wriiten. When 'shutdown' (3)is configured, the value is changed to 'shutdownInProgress' (2). This is because shutdownInProgress is used to indicate that shutdown process has been initiated by setting the object as shutdown but the process is not comitted. The value should be changed to shutdown once LLDP is shut on all ports and memory is released.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER start(1), shutdownInProgress(2), shutdown(3)  

fsLldpModuleStatus 1.3.6.1.4.1.207.1.4.167.158.1.2
The administrative module status of LLDP module. This enables or disables LLDP in the system. A value of 'enabled' (1) indicates that LLDP is enabled in the device and can be enabled port-wise. A value of 'disabled' (2) indicates that LLDP is disabled in the device and also disabled on all ports. When LLLDP module status is changed from enabled to disabled, a global timer (instead of port specific timers) is started to ensure the successful transmission of shutdown frame on all ports. Module status change from disabled to enabled is not allowed when the global timer is running (i.e., when disable is in progress).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

fsLldpTraceInput 1.3.6.1.4.1.207.1.4.167.158.1.3
This object stores the trace option string input given by the user. To enable particular trace the user has to enter the corresponding string(given below) assigned for that. And for enabling more than once traces the user has to enter the corresponding strings with SPACE delimiter between each string. For example, to enable - Init and Shutdown traces - Management traces - Neighbor delete traces - LLDP Port-descr TLV traces and - LLDP Power-via-mdi TLV traces The input string is, enable init-shut mgmt neigh-del port-descr pwr-mdi For example to disable - Init and Shutdown traces - Management traces - Neighbor delete traces - LLDP Port-descr TLV traces and - LLDP Power-via-mdi TLV traces The input string is, disable init-shut mgmt neigh-del port-descr pwr-mdi first value should be either enable or disable. The entered input string is parsed to get the trace options. And the corresponding bits of the trace options are set in fsLldpTraceOption object. enable - Enables the corresponding option. disable - Disables the corresponding option. init-shut - Init and Shutdown traces mgmt - Management traces data - Data Path traces ctrl - Control Plane traces pkt-dump - Packet Dump traces resource - Traces related to all resources except buffers all-fail - All Failure traces buf - Buffer allocation/ release traces neigh-add - Neighbor add traces neigh-del - Neighbor delete traces neigh-updt - Neighbor update traces neigh-drop - Neighbor drop traces neigh-ageout - Neighbor ageout traces critical - LLDP Critical traces all-tlv - LLDP All TLV traces chassis-id - LLDP Chassis-id TLV traces port-id - LLDP Port-id TLV trace ttl - LLDP Ttl TLV trace port-descr - LLDP Port-descr TLV traces sys-name - LLDP Sys-name TLV traces sys-descr - LLDP Sys-descr TLV traces sys-capab - LLDP Sys-capab TLV traces mgmt-addr - LLDP Mgmt-addr TLV traces port-vlan - LLDP Port-vlan TLV traces ppvlan - LLDP Port-proto-vlan TLV traces vlan-name - LLDP Vlan-name TLV traces proto-id - LLDP Proto-id TLV traces mac-phy - LLDP Mac-phy TLV traces pwr-mdi - LLDP Power-via-mdi TLV traces lagg - LLDP Link-agg TLV traces max-frame - LLDP Max-frame-size TLV traces - - Reserved By default critical trace is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..280)  

fsLldpTraceOption 1.3.6.1.4.1.207.1.4.167.158.1.4
This object is used to store the trace options that are enabled by the user. The bit positions of the traces is shown below Bit 0 - init-shut Bit 1 - mgmt Bit 2 - data Bit 3 - ctrl Bit 4 - pkt-dump Bit 5 - resource Bit 6 - all-fail Bit 7 - buf Bit 8 - neigh-add Bit 9 - neigh-del Bit 10 - neigh-updt Bit 11 - neigh-drop Bit 12 - neigh-ageout Bit 13 - critical Bit 14 - all-tlv Bit 15 - chassis-id Bit 16 - port-id Bit 17 - ttl Bit 18 - port-descr Bit 19 - sys-name Bit 20 - sys-descr Bit 21 - sys-capab Bit 22 - mgmt-addr Bit 23 - port-vlan Bit 24 - ppvlan Bit 25 - vlan-name Bit 26 - proto-id Bit 27 - mac-phy Bit 28 - pwr-mdi Bit 29 - lagg Bit 30 - max-frame Bit 31 - - By default critical trace(Bit 13) is set.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

fsLldpLocChassisIdSubtype 1.3.6.1.4.1.207.1.4.167.158.2.1
The type of encoding used to identify the chassis component associated with the local system. When chassis id subtype is configured as chassiscomp/portcomp/local it is mandatory to configure the fsLldpLocChassisId object. If fsLldpLocChassisId object is not configured then current value of fsLldpLocChassisId is advertised. When chassis id subtype is configured as ifalias/macaddr/nwaddr/ ifname it is not required to configure fsLldpLocChassisId object. System specific values are used for setting fsLldpLocChassisId object.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER chassiscomp(1), ifalias(2), portcomp(3), macaddr(4), nwaddr(5), ifname(6), local(7)  

fsLldpLocChassisId 1.3.6.1.4.1.207.1.4.167.158.2.2
The string value used to identify the chassis component associated with the local system. Write operation to this object is allowed only when the chassis id subtype is configured as chassiscomp/portcomp/local. When chassis id subtype is configured as ifalias/macaddr/nwaddr/ifname system specific values are used and hence write operation to this object is not allowed.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..255)  

fsLldpLocPortTable 1.3.6.1.4.1.207.1.4.167.158.2.3
This table contains one or more rows per port information associated with the local system known to this agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FsLldpLocPortEntry

fsLldpLocPortEntry 1.3.6.1.4.1.207.1.4.167.158.2.3.1
Information about a particular port component. Entries may be created and deleted in this table by the agent.
Status: current Access: not-accessible
OBJECT-TYPE    
  FsLldpLocPortEntry  

fsLldpLocPortIdSubtype 1.3.6.1.4.1.207.1.4.167.158.2.3.1.1
The type of port identifier encoding used to identify the port component associated with the local port. When port id subtype is configured as portcomp/local it is mandatory to configure the fsLldpLocPortId object. If fsLldpLocPortId object is not configured then current value of fsLldpLocPortId is advertised. When chassis id subtype is configured as ifalias/macaddr/nwaddr/ ifname/agentcircuitid it is not required to configure fsLldpLocPortId object. System specific values are used for setting fsLldpLocPortId object.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ifalias(1), portcomp(2), macaddr(3), nwaddr(4), ifname(5), agentcircuitid(6), local(7)  

fsLldpLocPortId 1.3.6.1.4.1.207.1.4.167.158.2.3.1.2
TThe string value used to identify the port component associated with the local port. Write operation to this object is allowed only when the chassis id subtype is configured as chassiscomp/portcomp/local. When chassis id subtype is configured as ifalias/macaddr/nwaddr/ifname system specific values are used and hence write operation to this object is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..255)  

fsLldpPortConfigNotificationType 1.3.6.1.4.1.207.1.4.167.158.2.3.1.3
This object is used to set the notification type. If the associated fsLldpNotificationType object has a value of remTabChg (1),then LLDP agent sends trap notification to NMS whenever remote table change occurs. If the associated fsLldpNotificationType object has a value of misCfg (1),then LLDP agent sends trap notification to NMS whenever mis-configuration is identified. If the associated fsLldpNotificationType object has a value of remTabChgAndMisCfg(3),then LLDP agent sends trap notification to NMS whenever remote table change occurs or/and whenever mis-configuration is identified. LLDP agent send the trap messages only when MIB Object lldpPortConfigNotificationEnable is true.So fsLldpNotificationType Object is valid when lldpPortConfigNotificationEnable Object is true.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER remTabChg(1), misCfg(2), remTabChgAndMisCfg(3)  

fsLldpMemAllocFailure 1.3.6.1.4.1.207.1.4.167.158.3.1
This object gives the count of total memory allocation failures
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

fsLldpInputQOverFlows 1.3.6.1.4.1.207.1.4.167.158.3.2
This object gives the count of total input queue overflows
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

fsLldpStatsRemTablesUpdates 1.3.6.1.4.1.207.1.4.167.158.3.3
The number of times any information advertised by a particular MSAP is updated in tables contained in lldpRemoteSystemsData and lldpExtensions objects.
Status: current Access: read-only
OBJECT-TYPE    
  ZeroBasedCounter32  

fsLldpTraps 1.3.6.1.4.1.207.1.4.167.158.4.0
OBJECT IDENTIFIER    

fsLldpRemTablesChange 1.3.6.1.4.1.207.1.4.167.158.4.0.1
A fsLldpRemTablesChange notification is sent when the value of lldpStatsRemTableLastChangeTime changes. It can be utilized by an NMS to trigger LLDP remote systems table maintenance polls. Note that transmission of fsLldpRemTablesChange notifications are throttled by the agent, as specified by the 'lldpNotificationInterval' object. The first four objects are already mentioned in the standard LLDP mib. As the Table Updation notification is also sent in the same notification PDU these objects are moved to proprietary mib.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpExceedsMaxFrameSize 1.3.6.1.4.1.207.1.4.167.158.4.0.2
A fsLldpExceedsMaxFrameSize notification is sent if the size of LLDP frame to be transmitted exceeds the maximum frame size (1522 bytes). This can occur if many number of TLVs need to be included in a single frame . It notifies the NMS that the information obtained about this system from its neighbor is not complete.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpDupChasisId 1.3.6.1.4.1.207.1.4.167.158.4.0.3
A fsLldpDupChasisId notification sent if the configured chasisId and Received chasisId from the neighbor is same. It notifies the NMS that the information obtained from its neighbor is Duplicate.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpDupSystemName 1.3.6.1.4.1.207.1.4.167.158.4.0.4
A fsLldpDupSystemName notification sent if the configured system name and Received system name from the neighbor is same. It notifies the NMS that the information obtained from its neighbor is Duplicate.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpDupManagmentAddress 1.3.6.1.4.1.207.1.4.167.158.4.0.5
A fsLldpDupManagementAddress notification sent if the configured management address and Received management address from the neighbor is same. It notifies the NMS that the information obtained from its neighbor is Duplicate.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpMisConfigPortVlanID 1.3.6.1.4.1.207.1.4.167.158.4.0.6
A fsLldpMisConfigPortVlanID notification sent if the Port VlanId of two systems connected to the same link is different. It notifies the NMS that the information obtained from its neighbor is mis-configured.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpMisConfigPortProtoVlanID 1.3.6.1.4.1.207.1.4.167.158.4.0.7
A fsLldpMisConfigPortProtoVlanID notification sent if the Port and protocol VlanId of two systems connected to the same link is different. lldpRemPortId and lldpRemChassisId information sent to identify the remote system. lldpXdot1RemProtoVlanId is not accesiable since it is the index, so sending the lldpXdot1RemProtoVlanSupported information, to know which Port and Protocol VlanId is MisConfigured. PPVID will be sent along with the OID. It notifies the NMS that the information obtained from its neighbor is mis-configured.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpMisConfigVlanName 1.3.6.1.4.1.207.1.4.167.158.4.0.8
A fsLldpMisConfigVlanName notification sent if the vlan name of two systems connected to the same link is different. It notifies the NMS that the information obtained from its neighbor is mis-configured.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpMisConfigProtocolIdentity 1.3.6.1.4.1.207.1.4.167.158.4.0.9
A fsLldpMisConfigProtocolIdentity notification sent if the protocol identity information (example spanning Tree protocol, the Link Aggregation protocol and proprietary protocol) of two systems connected to the same link is different. It notifies the NMS that the information obtained from its neighbor is mis-configured.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpMisConfigLinkAggStatus 1.3.6.1.4.1.207.1.4.167.158.4.0.10
A fsLldpMisConfigLinkAggStatus notification sent if the Link aggregation configuration of two systems connected to the same link is different. It is possible that if one system formed a link aggregation with a remote port while the other system is unaware of the aggregation. This type of configuration may cause network loops or unpredictable communication. It notifies the NMS that the information obtained from its neighbor is mis-configured.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpMisConfigPowerMDI 1.3.6.1.4.1.207.1.4.167.158.4.0.11
A fsLldpMisConfigPowerMDI notification sent if the power class configuration of two systems connected to the same link is different. It notifies the NMS that the information obtained from its neighbor is mis-configured.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpMisConfigMaxFrameSize 1.3.6.1.4.1.207.1.4.167.158.4.0.12
A fsLldpMisConfigMaxFrameSize notification sent if the maximum frame size configuration of two systems connected to the same link is different. Difference in maximum frame size can result in loss of frames if the sending station advertised maximum frame size is larger than the receiveing station. It notifies the NMS that the information obtained from its neighbor is mis-configured.
Status: current Access: read-only
NOTIFICATION-TYPE    

fsLldpMisConfigOperMauType 1.3.6.1.4.1.207.1.4.167.158.4.0.13
A fsLldpMisConfigOperMauType notification sent if the Operational MauType of the two systems connected to the same link is different. It notifies the NMS that the information obtained from its neighbor is mis-configured.
Status: current Access: read-only
NOTIFICATION-TYPE    

voicevlanSystem 1.3.6.1.4.1.207.1.4.167.163.1
OBJECT IDENTIFIER    

voicevlanOUI 1.3.6.1.4.1.207.1.4.167.163.2
OBJECT IDENTIFIER    

voiceVlanMode 1.3.6.1.4.1.207.1.4.167.163.1.2
Voice VLAN is a feature that allows you to automatically place the voice traffic from IP phone to an assigned VLAN to enhance the VoIP service. This object is for enabling or disabling Voice Vlan function in the system. If the Vlan mode is in Asymmetric VLAN mode, Voice VLAN can not be enabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

voiceVlanId 1.3.6.1.4.1.207.1.4.167.163.1.3
The ID of VLAN that you want the voice traffic to be in. It must be a exist vlan id.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

voiceVlanTimeout 1.3.6.1.4.1.207.1.4.167.163.1.4
A period of time in hour to remove a port from voice VLAN if the port is an automatic VLAN member. The Timeout range is 1~120 hours. Default aging time is 1 hour.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

voiceVlanPriority 1.3.6.1.4.1.207.1.4.167.163.1.5
The 802.1p priority levels of the traffic in the Voice VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER highest(0), high(1), medium(2), low(3)  

voicevlanPortControlTable 1.3.6.1.4.1.207.1.4.167.163.1.6
A table that contains Voice Vlan Port Control configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoiceVlanPortControlEntry

voicevlanPortControlEntry 1.3.6.1.4.1.207.1.4.167.163.1.6.1
A list of Voice Vlan Control configuration parameters for each Port on this device.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoiceVlanPortControlEntry  

voicevlanPortControlIndex 1.3.6.1.4.1.207.1.4.167.163.1.6.1.1
The voice vlan port index.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

voicevlanPortAutoDetection 1.3.6.1.4.1.207.1.4.167.163.1.6.1.2
This object is for enabling or disabling Voice Vlan Auto Detection in the port. If the auto detection is enable, switch will add this port to the voice VLAN automatically if it detects the device OUI matches the Telephony OUI. If the port is a static member of voice vlan or a LA member, it can not enable voice vlan auto detection.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

voicevlanPortState 1.3.6.1.4.1.207.1.4.167.163.1.6.1.3
This object indicates Voice vlan state to this Port. manual - this port is a static member of voice vlan. dynamic - this port is a dynamic member of voice vlan. none - this port is not a member of voice vlan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER manual(1), dynamic(2), none(3)  

voicevlanOUITable 1.3.6.1.4.1.207.1.4.167.163.2.1
A voice vlan OUI entry containing the description and mac.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoicevlanOUIEntry

voicevlanOUIEntry 1.3.6.1.4.1.207.1.4.167.163.2.1.1
A voice vlan OUI entry containing the description and mac.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoicevlanOUIEntry  

voicevlanOUITelephonyOUI 1.3.6.1.4.1.207.1.4.167.163.2.1.1.1
An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the voice traffic's OUI that user created.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

voicevlanOUIDescription 1.3.6.1.4.1.207.1.4.167.163.2.1.1.2
The Description for the OUI.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

voicevlanOUIMask 1.3.6.1.4.1.207.1.4.167.163.2.1.1.3
Voice vlan OUI Mask. Always be FF:FF:FF:00:00:00.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

voicevlanOUIStatus 1.3.6.1.4.1.207.1.4.167.163.2.1.1.4
This object indicates the status of this entry. To create a new entry, you must set the voicevlanOUIStatus to be CreateAndGo, then this entry will turn to be Active.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

trafficSegTable 1.3.6.1.4.1.207.1.4.167.165.1
A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TrafficSegEntry

trafficSegEntry 1.3.6.1.4.1.207.1.4.167.165.1.1
There is one entry in this table for each created port-channel port
Status: current Access: not-accessible
OBJECT-TYPE    
  TrafficSegEntry  

trafficSegIfIndex 1.3.6.1.4.1.207.1.4.167.165.1.1.1
The ifIndex of the port-channel(Aggregator's interface index).
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

trafficSegMemberList 1.3.6.1.4.1.207.1.4.167.165.1.1.2
List of the member port of the port-channel.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

atiAcl 1.3.6.1.4.1.207.1.4.167.166.1
OBJECT IDENTIFIER    

atiMacFilter 1.3.6.1.4.1.207.1.4.167.166.2
OBJECT IDENTIFIER    

atiAclClassifierTable 1.3.6.1.4.1.207.1.4.167.166.1.1
ACL Classifier entry table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtiAclClassifierEntry

atiAclClassifierEntry 1.3.6.1.4.1.207.1.4.167.166.1.1.1
Classifier is used to specify a packet type for Policies.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtiAclClassifierEntry  

atiAclClassifierIndex 1.3.6.1.4.1.207.1.4.167.166.1.1.1.1
The index of the Classifier entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

atiAclClassifierSrcMac 1.3.6.1.4.1.207.1.4.167.166.1.1.1.2
Source MAC address.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

atiAclClassifierSrcMacMaskLen 1.3.6.1.4.1.207.1.4.167.166.1.1.1.3
Source MAC mask length. 1-48: length in bits 0: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..48  

atiAclClassifierDstMac 1.3.6.1.4.1.207.1.4.167.166.1.1.1.4
Destination MAC address.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

atiAclClassifierDstMacMaskLen 1.3.6.1.4.1.207.1.4.167.166.1.1.1.5
Destination MAC mask length. 1-48: length in bits 0: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..48  

atiAclClassifierVlanId 1.3.6.1.4.1.207.1.4.167.166.1.1.1.6
802.1Q Vlan Id. 1-4000: Vlan Id -1: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1..4000  

atiAclClassifierCos 1.3.6.1.4.1.207.1.4.167.166.1.1.1.7
802.1p priority. 0-7: 802.1p priority value -1: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1..7  

atiAclClassifierEtherType 1.3.6.1.4.1.207.1.4.167.166.1.1.1.8
EtherType. 0-65535: EtherType number -1: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1..65535  

atiAclClassifierSrcIp 1.3.6.1.4.1.207.1.4.167.166.1.1.1.10
Source IP address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

atiAclClassifierSrcIpMaskLen 1.3.6.1.4.1.207.1.4.167.166.1.1.1.11
Source IP mask length. 1-32: length in bits 0: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..32  

atiAclClassifierDstIp 1.3.6.1.4.1.207.1.4.167.166.1.1.1.12
Destination IP address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

atiAclClassifierDstIpMaskLen 1.3.6.1.4.1.207.1.4.167.166.1.1.1.13
Destination IP mask length. 1-32: length in bits 0: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..32  

atiAclClassifierDscp 1.3.6.1.4.1.207.1.4.167.166.1.1.1.14
Differentiated Services Code Point. 0-63: DSCP value -1: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1..63  

atiAclClassifierProtocol 1.3.6.1.4.1.207.1.4.167.166.1.1.1.15
Layer 4 protocol type. 0-255: Layer 4 protocol number -1: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1..255  

atiAclClassifierSrcPort 1.3.6.1.4.1.207.1.4.167.166.1.1.1.20
TCP/UDP Source port. 0-65535: port number -1: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1..65535  

atiAclClassifierDstPort 1.3.6.1.4.1.207.1.4.167.166.1.1.1.21
TCP/UDP Destination port. 0-65535: port number -1: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1..65535  

atiAclClassifierRowStatus 1.3.6.1.4.1.207.1.4.167.166.1.1.1.30
The row status of the entry. 1: write - enable the entry read - entry is enabled 2: write - disable the entry read - entry is disabled 3: read - entry is not ready 5: write - create the entry 6: write - delete the entry
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

atiAclProfileActionTable 1.3.6.1.4.1.207.1.4.167.166.1.2
ACL Profile Action entry table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtiAclProfileActionEntry

atiAclProfileActionEntry 1.3.6.1.4.1.207.1.4.167.166.1.2.1
Profile Action is used to manipulate the DSCP or CoS values in a packet.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtiAclProfileActionEntry  

atiAclProfileActionIndex 1.3.6.1.4.1.207.1.4.167.166.1.2.1.1
The index of the Action entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..72  

atiAclProfileActionCos 1.3.6.1.4.1.207.1.4.167.166.1.2.1.2
Policied-Cos. 0-7: 802.1p priority value -1: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1..7  

atiAclProfileActionDscp 1.3.6.1.4.1.207.1.4.167.166.1.2.1.3
Policied-DSCP. 0-63: DSCP value -1: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1..63  

atiAclProfileActionRowStatus 1.3.6.1.4.1.207.1.4.167.166.1.2.1.4
The row status of the entry. 1: write - enable the entry read - entry is enabled 2: write - disable the entry read - entry is disabled 3: read - entry is not ready 5: write - create the entry 6: write - delete the entry
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

atiAclInProfileActionTable 1.3.6.1.4.1.207.1.4.167.166.1.3
ACL In-Profile Action entry table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtiAclInProfileActionEntry

atiAclInProfileActionEntry 1.3.6.1.4.1.207.1.4.167.166.1.3.1
In-Profile Action is used to assign an action to a policy.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtiAclInProfileActionEntry  

atiAclInProfileActionIndex 1.3.6.1.4.1.207.1.4.167.166.1.3.1.1
The index of the In-Profile Action entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

atiAclInProfileActionPermitDeny 1.3.6.1.4.1.207.1.4.167.166.1.3.1.2
Permit/Deny action. 0: Permit 1: Deny
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1  

atiAclInProfileActionActionId 1.3.6.1.4.1.207.1.4.167.166.1.3.1.3
The index of Action entry used by this In-Profile entry. 1-72: Action entry index 0: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..72  

atiAclInProfileActionRowStatus 1.3.6.1.4.1.207.1.4.167.166.1.3.1.4
The row status of the entry. 1: write - enable the entry read - entry is enabled 2: write - disable the entry read - entry is disabled 3: read - entry is not ready 5: write - create the entry 6: write - delete the entry
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

atiAclOutProfileActionTable 1.3.6.1.4.1.207.1.4.167.166.1.4
ACL Out-Profile Action entry table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtiAclOutProfileActionEntry

atiAclOutProfileActionEntry 1.3.6.1.4.1.207.1.4.167.166.1.4.1
Out-Profile Action is used to assign a classifier index to a profile action ID as well as a committed rate and a burst size
Status: current Access: not-accessible
OBJECT-TYPE    
  AtiAclOutProfileActionEntry  

atiAclOutProfileActionIndex 1.3.6.1.4.1.207.1.4.167.166.1.4.1.1
The index of the Out-Profile Action entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

atiAclOutProfileActionPermitDeny 1.3.6.1.4.1.207.1.4.167.166.1.4.1.2
Permit/Deny action. 0: Permit 1: Deny
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1  

atiAclOutProfileActionCommittedRate 1.3.6.1.4.1.207.1.4.167.166.1.4.1.3
Committed rate in Kbps.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 64..1000000  

atiAclOutProfileActionBurstSize 1.3.6.1.4.1.207.1.4.167.166.1.4.1.4
Max burst size which is the maximum amount of data in KB.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 16..64  

atiAclOutProfileActionActionId 1.3.6.1.4.1.207.1.4.167.166.1.4.1.5
The index of Action entry used by this Out-Profile entry. 1-72: Action entry index 0: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..72  

atiAclOutProfileActionRowStatus 1.3.6.1.4.1.207.1.4.167.166.1.4.1.6
The row status of the entry. 1: write - enable the entry read - entry is enabled 2: write - disable the entry read - entry is disabled 3: read - entry is not ready 5: write - create the entry 6: write - delete the entry
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

atiAclPortListTable 1.3.6.1.4.1.207.1.4.167.166.1.5
ACL Port-List entry table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtiAclPortListEntry

atiAclPortListEntry 1.3.6.1.4.1.207.1.4.167.166.1.5.1
Port-List is used to specify a list of ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtiAclPortListEntry  

atiAclPortListIndex 1.3.6.1.4.1.207.1.4.167.166.1.5.1.1
The index of the Port-List entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

atiAclPortListString 1.3.6.1.4.1.207.1.4.167.166.1.5.1.2
Port-list string. e.g. 1,3,5-8
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..63)  

atiAclPortListRowStatus 1.3.6.1.4.1.207.1.4.167.166.1.5.1.3
The row status of the entry. 1: write - enable the entry read - entry is enabled 2: write - disable the entry read - entry is disabled 3: read - entry is not ready 5: write - create the entry 6: write - delete the entry
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

atiAclPolicyTable 1.3.6.1.4.1.207.1.4.167.166.1.6
ACL Policy entry table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtiAclPolicyEntry

atiAclPolicyEntry 1.3.6.1.4.1.207.1.4.167.166.1.6.1
Policy controls the ingress traffic on a port. It defines a category of traffic and the action of the port when it receives packets of the category.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtiAclPolicyEntry  

atiAclPolicyIndex 1.3.6.1.4.1.207.1.4.167.166.1.6.1.1
The index of the Policy entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

atiAclPolicyClassifierIndex 1.3.6.1.4.1.207.1.4.167.166.1.6.1.2
The index of Classifier entry used by this Policy entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

atiAclPolicySequence 1.3.6.1.4.1.207.1.4.167.166.1.6.1.3
The sequence of the Policy entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..64  

atiAclPolicyInProfileIndex 1.3.6.1.4.1.207.1.4.167.166.1.6.1.4
The index of In-Profile entry used by this Policy entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

atiAclPolicyOutProfileIndex 1.3.6.1.4.1.207.1.4.167.166.1.6.1.5
The index of Out-Profile entry used by this Policy entry. 0: Ignored
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

atiAclPolicyPortListIndex 1.3.6.1.4.1.207.1.4.167.166.1.6.1.6
The index of Port-List entry used by this Policy entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

atiAclPolicyRowStatus 1.3.6.1.4.1.207.1.4.167.166.1.6.1.7
The row status of the entry. 1: write - enable the entry read - entry is enabled 2: write - disable the entry read - entry is disabled 3: read - entry is not ready 5: write - create the entry 6: write - delete the entry
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

atiDstMacFilterTable 1.3.6.1.4.1.207.1.4.167.166.2.1
DstMacFilter entry table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtiDstMacFilterEntry

atiDstMacFilterEntry 1.3.6.1.4.1.207.1.4.167.166.2.1.1
DstMacFilter is used to filter the packets by the specific Destination MAC.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtiDstMacFilterEntry  

atiDstMacFilterIndex 1.3.6.1.4.1.207.1.4.167.166.2.1.1.1
The index of the DstMacFilter entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..40  

atiDstMacFilterAddress 1.3.6.1.4.1.207.1.4.167.166.2.1.1.2
Destnation MAC address
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

atiDstMacFilterRowStatus 1.3.6.1.4.1.207.1.4.167.166.2.1.1.3
The row status of the entry. 1: write - enable the entry read - entry is enabled 2: write - disable the entry read - entry is disabled 3: read - entry is not ready 5: write - create the entry 6: write - delete the entry
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dhcpSnoopSystemStatus 1.3.6.1.4.1.207.1.4.167.181.1
Enable/Disable DHCP Snooping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpSnoopOption82Insertion 1.3.6.1.4.1.207.1.4.167.181.2
Determine if to insert DHCP option 82 into packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpSnoopPassThroughOption82 1.3.6.1.4.1.207.1.4.167.181.3
Determine if to pass through DHCP packets with option 82.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpSnoopVerifyMACAddress 1.3.6.1.4.1.207.1.4.167.181.4
Determine if to verify MAC address for incoming DHCP packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpSnoopBackupDatabase 1.3.6.1.4.1.207.1.4.167.181.5
Determine if to backup database to flash memory.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpSnoopBackupDatabaseInterval 1.3.6.1.4.1.207.1.4.167.181.6
Determine the period to backup database.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 600..86400  

dhcpSnoopVLANSettingTable 1.3.6.1.4.1.207.1.4.167.181.7
A table of DHCP snooping VLAN settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDhcpSnoopVLANSettingEntry

dhcpSnoopVLANSettingEntry 1.3.6.1.4.1.207.1.4.167.181.7.1
The entry of DHCP snooping VLAN setting table.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDhcpSnoopVLANSettingEntry  

dhcpSnoopVLANSettingVID 1.3.6.1.4.1.207.1.4.167.181.7.1.1
The VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4094  

dhcpSnoopVLANSettingStatus 1.3.6.1.4.1.207.1.4.167.181.7.1.2
The VLAN status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dhcpSnoopPortSettingTable 1.3.6.1.4.1.207.1.4.167.181.8
A table of DHCP snooping port settings.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDhcpSnoopPortSettingEntry

dhcpSnoopPortSettingEntry 1.3.6.1.4.1.207.1.4.167.181.8.1
The entry of DHCP snooping port setting table.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDhcpSnoopPortSettingEntry  

dhcpSnoopPortSettingIndex 1.3.6.1.4.1.207.1.4.167.181.8.1.1
The port number.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

dhcpSnoopPortSettingStatus 1.3.6.1.4.1.207.1.4.167.181.8.1.2
The port status.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER untrusted(0), trusted(1)  

dhcpSnoopBindindDatabaseTable 1.3.6.1.4.1.207.1.4.167.181.9
A table of DHCP snooping bindind database.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TabDhcpSnoopBindindDatabaseEntry

dhcpSnoopBindindDatabaseEntry 1.3.6.1.4.1.207.1.4.167.181.9.1
The entry of DHCP snooping bindind database table.
Status: current Access: not-accessible
OBJECT-TYPE    
  TabDhcpSnoopBindindDatabaseEntry  

dhcpSnoopBindindDBMacAddress 1.3.6.1.4.1.207.1.4.167.181.9.1.1
The MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

dhcpSnoopBindindDBVLANID 1.3.6.1.4.1.207.1.4.167.181.9.1.2
The VLAN ID.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..4094  

dhcpSnoopBindindDBIPAddress 1.3.6.1.4.1.207.1.4.167.181.9.1.3
The IP address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dhcpSnoopBindindDBPortNumber 1.3.6.1.4.1.207.1.4.167.181.9.1.4
The port number.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

dhcpSnoopBindindDBType 1.3.6.1.4.1.207.1.4.167.181.9.1.5
The entry type.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dynamic(0), static(1)  

dhcpSnoopBindindDBLeaseTime 1.3.6.1.4.1.207.1.4.167.181.9.1.6
The DHCP lease time.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

dhcpSnoopBindindDBRowStatus 1.3.6.1.4.1.207.1.4.167.181.9.1.7
The entry row status.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus