ASANTE-AH1012-MIB

File: ASANTE-AH1012-MIB.mib (126433 bytes)

Imported modules

RFC1155-SMI RFC-1212 SNMPv2-SMI
RFC-1215

Imported symbols

private NetworkAddress IpAddress
Counter Gauge TimeTicks
OBJECT-TYPE enterprises TRAP-TYPE

Defined Types

DisplayString  
OCTET STRING    

PhysAddress  
OCTET STRING    

IpagentTrapRcvrEntry  
SEQUENCE    
  ipagentTrapRcvrIpAddr IpAddress
  ipagentTrapRcvrStatus INTEGER
  ipagentTrapRcvrComm OCTET STRING

ConcChassisPsEntry  
SEQUENCE    
  concChassisPsIndex INTEGER
  concChassisPsModuleType INTEGER
  concChassisPsStatus INTEGER

ConcChassisGrpEntry  
SEQUENCE    
  concChassisGrpIndex INTEGER
  concChassisGrpNumberPort INTEGER
  concChassisGrpType INTEGER
  concChassisGrpDescr DisplayString
  concChassisGrpHwRev INTEGER

EnetGrpStatisticsEntry  
SEQUENCE    
  eGrpStatIndex INTEGER
  eGrpStatReadableFrames Counter
  eGrpStatMcastFrames Counter
  eGrpStatBcastFrames Counter
  eGrpStatFrameTooLongs Counter
  eGrpStatRunts Counter
  eGrpStatAlignmentErrors Counter
  eGrpStatFragmentErrors Counter
  eGrpStatFCSErrors Counter
  eGrpStatIFGErrors Counter
  eGrpStatDataRateMismatchs Counter
  eGrpStatShortEvents Counter
  eGrpStatCollisions Counter
  eGrpStatLateCollisions Counter
  eGrpStatMJLPs Counter
  eGrpStatAutoPartitions Counter
  eGrpStatSFDMissings Counter
  eGrpStatBadFrames Counter

EnetPortStatisticsEntry  
SEQUENCE    
  ePortGrpIndex INTEGER
  ePortIndex INTEGER
  ePortStatReadableFrames Counter
  ePortStatMcastFrames Counter
  ePortStatBcastFrames Counter
  ePortStatFrameTooLongs Counter
  ePortStatRunts Counter
  ePortStatAlignmentErrors Counter
  ePortStatFragmentErrors Counter
  ePortStatFCSErrors Counter
  ePortStatIFGErrors Counter
  ePortStatDataRateMismatchs Counter
  ePortStatShortEvents Counter
  ePortStatCollisions Counter
  ePortStatLateCollisions Counter
  ePortStatMJLPs Counter
  ePortStatAutoPartitions Counter
  ePortStatSFDMissings Counter
  ePortStatBadFrames Counter

EnetTrafficMatrixEntry  
SEQUENCE    
  eTrafficMatrixLength INTEGER
  eTrafficMatrixRange INTEGER
  eTrafficMatrixFramesCounts Counter

EnetPortRateEntry  
SEQUENCE    
  ePortRateGrpIndex INTEGER
  ePortRatePortIndex INTEGER
  ePortRateReadableFrames INTEGER
  ePortRateMcastFrames INTEGER
  ePortRateBcastFrames INTEGER
  ePortRateFrameTooLongs INTEGER
  ePortRateRunts INTEGER
  ePortRateAlignmentErrors INTEGER
  ePortRateFragmentErrors INTEGER
  ePortRateFCSErrors INTEGER
  ePortRateIFGErrors INTEGER
  ePortRateDataRateMismatch INTEGER
  ePortRateShortEvents INTEGER
  ePortRateCollisions INTEGER
  ePortRateLateCollisions INTEGER
  ePortRateMJLPs INTEGER
  ePortRateAutoPartitions INTEGER
  ePortRateSFDMissings INTEGER
  ePortRateBadFrames INTEGER

EPortStateCtrlEntry  
SEQUENCE    
  ePortStateGrpIndex INTEGER
  ePortStatePortIndex INTEGER
  ePortStateType INTEGER
  ePortStateLinkStatus INTEGER
  ePortStateLinkIntegTest INTEGER
  ePortStateAutoPartStatus INTEGER
  ePortStateJabberStatus INTEGER
  ePortStateJabberState INTEGER
  ePortStateAdminState INTEGER
  ePortStateRDTState INTEGER
  ePortStatePolarityStatus INTEGER
  ePortStatePolarityState INTEGER

NodeSummaryEntry  
SEQUENCE    
  nodeSummaryGrpIndex INTEGER
  nodeSummaryPortIndex INTEGER
  nodeSummarySrcMacAddr PhysAddress
  nodeSummaryDestMacAddr PhysAddress
  nodeSummaryEtherType INTEGER
  nodeSummaryIpAddrPair OCTET STRING
  nodeSummaryTimeStamp TimeTicks

NodeSecuLev1Entry  
SEQUENCE    
  nodeSecuLev1GrpIndex INTEGER
  nodeSecuLev1PortIndex INTEGER
  nodeSecuLev1Status INTEGER
  nodeSecuLev1AllowedAddr PhysAddress
  nodeSecuLev1Action INTEGER

ThresholdLev1Entry  
SEQUENCE    
  thresholdLev1Index INTEGER
  thresholdLev1Status INTEGER
  thresholdLev1Target INTEGER
  thresholdLev1GroupIndex INTEGER
  thresholdLev1PortIndex INTEGER
  thresholdLev1Subject INTEGER
  thresholdLev1SampleType INTEGER
  thresholdLev1StartupAlarm INTEGER
  thresholdLev1WaterMark INTEGER
  thresholdLev1DetectedValue INTEGER
  thresholdLev1RisingEvent INTEGER
  thresholdLev1FallingEvent INTEGER
  thresholdLev1Interval INTEGER
  thresholdLev1OwnerString OCTET STRING

Defined Values

asante 1.3.6.1.4.1.298
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.298.1
OBJECT IDENTIFIER    

productId 1.3.6.1.4.1.298.2
OBJECT IDENTIFIER    

snmpAgent 1.3.6.1.4.1.298.1.1
OBJECT IDENTIFIER    

adaptCard 1.3.6.1.4.1.298.1.2
OBJECT IDENTIFIER    

concentrator 1.3.6.1.4.1.298.1.3
OBJECT IDENTIFIER    

agentSw 1.3.6.1.4.1.298.1.1.1
OBJECT IDENTIFIER    

agentFw 1.3.6.1.4.1.298.1.1.2
OBJECT IDENTIFIER    

agentHw 1.3.6.1.4.1.298.1.1.3
OBJECT IDENTIFIER    

agentNetProtocol 1.3.6.1.4.1.298.1.1.5
OBJECT IDENTIFIER    

ipagentProtocol 1.3.6.1.4.1.298.1.1.5.1
OBJECT IDENTIFIER    

concChassis 1.3.6.1.4.1.298.1.3.1
OBJECT IDENTIFIER    

concConfiguration 1.3.6.1.4.1.298.1.3.2
OBJECT IDENTIFIER    

concStatistics 1.3.6.1.4.1.298.1.3.3
OBJECT IDENTIFIER    

concStateCtrl 1.3.6.1.4.1.298.1.3.4
OBJECT IDENTIFIER    

concNodeMgt 1.3.6.1.4.1.298.1.3.5
OBJECT IDENTIFIER    

concAlarmMgt 1.3.6.1.4.1.298.1.3.6
OBJECT IDENTIFIER    

concBasicGrp 1.3.6.1.4.1.298.1.3.1.1
OBJECT IDENTIFIER    

eSmartHubConfig 1.3.6.1.4.1.298.1.3.2.1
OBJECT IDENTIFIER    

eStatistics 1.3.6.1.4.1.298.1.3.3.1
OBJECT IDENTIFIER    

eStateCtrl 1.3.6.1.4.1.298.1.3.4.1
OBJECT IDENTIFIER    

eGlobalStatistics 1.3.6.1.4.1.298.1.3.3.1.1
OBJECT IDENTIFIER    

agentNetProtoStkCapMap 1.3.6.1.4.1.298.1.1.4
This octet string represents the current protocol stack configuration supported by the agent, encoded as a bit string. Each protocol stack is represented by a single bit. When the value of a bit = 1, it indicates that the protocol stack on the agent represented by that bit is supported; when zero, the protocol stack is not supported. The number of octets in the string is always integer multiple of the octet. The first protocol stack will encode in the least significant bit of the first octet. Current, only IP Stack(bit 0) and IPX Stack(bit 1) were defined, all other bits should be zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..4)  

agentRunTimeImageMajorVer 1.3.6.1.4.1.298.1.1.1.1
The major software version number of the agent run time image.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

agentRunTimeImageMinorVer 1.3.6.1.4.1.298.1.1.1.2
The minor software version number of the agent run time image.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

agentImageLoadMode 1.3.6.1.4.1.298.1.1.1.3
Tells hub whether the software image is to be loaded from the FLASH EPROM or from over the network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), localBoot(2), netBoot(3)  

agentRemoteBootInfo 1.3.6.1.4.1.298.1.1.1.4
The method for getting boot parameter information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), eepromBootInfo(2)  

agentRemoteBootProtocol 1.3.6.1.4.1.298.1.1.1.5
The netboot protocol that used to load the agent software.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), bootp-tftp(2), tftp-only(3)  

agentRemoteBootFile 1.3.6.1.4.1.298.1.1.1.6
The boot file name that is sent to the boot file server by agent boot code during boot time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

agentOutBandDialString 1.3.6.1.4.1.298.1.1.1.7
This is the initialization string used by the Network Management station to establish the out-of-band connection for modem only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

agentOutBandBaudRate 1.3.6.1.4.1.298.1.1.1.8
The baud rate setting for the out-of-band port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), b1200(2), b2400(3), b4800(4), b9600(5)  

agentReset 1.3.6.1.4.1.298.1.1.1.9
The object to allow software to perform 'push_button' system reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), reset(2), not-reset(3)  

agentHwReVer 1.3.6.1.4.1.298.1.1.3.1
The hardware reversion number of the network management module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

agentHwVer 1.3.6.1.4.1.298.1.1.3.2
The hardware model number of the network management module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

agentFwMajorVer 1.3.6.1.4.1.298.1.1.2.1
The major firmware version number of the agent prom code.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

agentFwMinorVer 1.3.6.1.4.1.298.1.1.2.2
The minor firmware version number of the agent prom code.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipagentIpAddr 1.3.6.1.4.1.298.1.1.5.1.1
The ipagent's administrative IP address. The current operational IP address can be obtained from the ipAdEntAddr in the ipAddrTable. This parameter will take effect only after reset hub. This parameter will always be updated in the EEPROM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipagentIpNetMask 1.3.6.1.4.1.298.1.1.5.1.2
The ipagent's administrative IP subnet mask. The current operational IP subnet mask can be obtained from the ipAdEntMask in the ipAddrTable. This parameter will take effect only after reset hub. This parameter will always be updated in the EEPROM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipagentDefaultGateway 1.3.6.1.4.1.298.1.1.5.1.3
The ipagent's administrative default gateway IP address. The current operational IP default gateway IP address can be obtained from the ipRouteDest in the ipRouteTable. This parameter will take effect only after reset hub. This parameter will always be updated in the EEPROM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipagentBootServerAddr 1.3.6.1.4.1.298.1.1.5.1.4
The IP address of the boot server that was used for booting this ipagent. This parameter will always be updated in the EEPROM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ipagentUnAuthIP 1.3.6.1.4.1.298.1.1.5.1.5
The IP address of the last station that tried to access this ipagent with an invalid community string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipagentUnAuthComm 1.3.6.1.4.1.298.1.1.5.1.6
The community string of the last station that tried to access this ipagent with an invalid community string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ipagentTrapRcvrTable 1.3.6.1.4.1.298.1.1.5.2
Table consisting of the list of Network Management Stations that are to receive traps generated by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpagentTrapRcvrEntry

ipagentTrapRcvrEntry 1.3.6.1.4.1.298.1.1.5.2.1
Destination IP address and community string for a particular trap server.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpagentTrapRcvrEntry  

ipagentTrapRcvrIpAddr 1.3.6.1.4.1.298.1.1.5.2.1.1
IP address for trap server receiving trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipagentTrapRcvrStatus 1.3.6.1.4.1.298.1.1.5.2.1.2
Validation of individual trap receiver. If value of this object is set to invalid(3), then that particular entry is deemed invalid, meaning that the address for that entry is no longer valid because the entry has been removed from the table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), invalid(3)  

ipagentTrapRcvrComm 1.3.6.1.4.1.298.1.1.5.2.1.3
Community string for traps sent to this trap receiver.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

concChassisType 1.3.6.1.4.1.298.1.3.1.1.1
The concentrator's chassis type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), aH1012(2)  

concChassisBkplType 1.3.6.1.4.1.298.1.3.1.1.2
The concentrator's chassis backplane type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), no-backplane(2)  

concChassisBkplRev 1.3.6.1.4.1.298.1.3.1.1.3
The concentrator's chassis backplane revision number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

concChassisPsTable 1.3.6.1.4.1.298.1.3.1.1.4
This table contains concentrator's power supply information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ConcChassisPsEntry

concChassisPsEntry 1.3.6.1.4.1.298.1.3.1.1.4.1
The entry in the table containing the information about a single power supply.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ConcChassisPsEntry  

concChassisPsIndex 1.3.6.1.4.1.298.1.3.1.1.4.1.1
The value of this object identifies the power supply table for which this entry contains power supply type and status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

concChassisPsModuleType 1.3.6.1.4.1.298.1.3.1.1.4.1.2
The value of this object identifies the power supply module type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1)  

concChassisPsStatus 1.3.6.1.4.1.298.1.3.1.1.4.1.3
The value of this object identifies the power supply module status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), good(2), bad(3)  

concChassisFanStatus 1.3.6.1.4.1.298.1.3.1.1.5
The value of this object identifies the fan status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), no-fan(2), good(3), bad(4)  

concChassisGroupCapacity 1.3.6.1.4.1.298.1.3.1.1.6
The number of groups that can be contained within the concentrator.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

concChassisGroupMap 1.3.6.1.4.1.298.1.3.1.1.7
This octet string represents the current configuration of groups, encoded as a bit string, each group is represented by a single bit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

concChassisGrpTable 1.3.6.1.4.1.298.1.3.1.1.8
A table that contains information about the group/slot in this chassis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ConcChassisGrpEntry

concChassisGrpEntry 1.3.6.1.4.1.298.1.3.1.1.8.1
A list of information for each slot in this chassis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ConcChassisGrpEntry  

concChassisGrpIndex 1.3.6.1.4.1.298.1.3.1.1.8.1.1
The value of this object identifies the chassis group table for which this entry contains group related information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

concChassisGrpNumberPort 1.3.6.1.4.1.298.1.3.1.1.8.1.2
The number of port is available for up/down link within this group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

concChassisGrpType 1.3.6.1.4.1.298.1.3.1.1.8.1.3
The value represents the function of this group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

concChassisGrpDescr 1.3.6.1.4.1.298.1.3.1.1.8.1.4
A description of this group device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

concChassisGrpHwRev 1.3.6.1.4.1.298.1.3.1.1.8.1.5
The hardware revision number of this particular group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

eSmartHubId 1.3.6.1.4.1.298.1.3.2.1.1
Hub MAC address (octet string) found from prom chip in hub.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

eSmartHubAssignedId 1.3.6.1.4.1.298.1.3.2.1.2
Assigned hub ID for Out-of-Band.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

eSmartHubTerSwitch 1.3.6.1.4.1.298.1.3.2.1.3
Status of position of PC/terminal switch located on rear panel of hub. Switches between serial and parallel communications for modem/PC or terminal connection to RS-232 Port. Up (off) for PC, down (on) for terminal. If position of switch is changed, there will be no change in this status until hub is reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), terminal(2), pc-modem(3)  

eSmartHubHwLoadPatStatus 1.3.6.1.4.1.298.1.3.2.1.4
Which logic configuration pattern is loaded into the Programmable Logic Device PLD.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

eSmartHubHwLoadPatCapacity 1.3.6.1.4.1.298.1.3.2.1.5
What kind of function the PLD can perform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

eSmartHubNodeAgeTimer 1.3.6.1.4.1.298.1.3.2.1.6
How long to keep node entry in node summary table, measured in sec. The maximum is 11 hours.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

eSmartHub3in1LnConStatus 1.3.6.1.4.1.298.1.3.2.1.7
Status of 3In1 Uplink which is located on rear panel of hub. Describes the physical link type or types currently connected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), uTP(2), aUI(3), uTP-and-AUI(4)  

eSmartHub3in1StateCtrl 1.3.6.1.4.1.298.1.3.2.1.8
Whether using Auto-sense or manually selected a particular media type for the uplink connection. If using Auto-sense it first tries AUI. If AUI is not present then 10T. If neither AUI nor 10T is present, then it defaults to BNC.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), uTP(2), bNC(3), aUI(4), auto(5)  

eGlobalHubReadableFrames 1.3.6.1.4.1.298.1.3.3.1.1.1
Global counter of good or readable frames for this hub. Frame is between 64 and 1518 bytes in length and has SFD and good FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubMcastFrames 1.3.6.1.4.1.298.1.3.3.1.1.2
Global counter of number of multicast frames for this hub. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubBcastFrames 1.3.6.1.4.1.298.1.3.3.1.1.3
Global counter of number of broadcast frames for his hub. All 1s in network destination address. Multicast packets are not included.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubFrameTooLongs 1.3.6.1.4.1.298.1.3.3.1.1.4
Global counter, for this hub, of data frames longer than 1518 bytes, with a SFD and good FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubRunts 1.3.6.1.4.1.298.1.3.3.1.1.5
Global counter, for this hub, of data frames with size less than 64 bytes, with no CRC or alignment errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubAlignmentErrors 1.3.6.1.4.1.298.1.3.3.1.1.6
Global counter, for this hub, of frames which are not integer multiples of 1 byte.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubFragmentErrors 1.3.6.1.4.1.298.1.3.3.1.1.7
Global counter, for this hub, of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubFCSErrors 1.3.6.1.4.1.298.1.3.3.1.1.8
Global counter, for this hub, of frames that failed Cyclic Redundancy Check (CRC).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubIFGErrors 1.3.6.1.4.1.298.1.3.3.1.1.9
Global counter, for this hub, of occurrences of Interframe Gap Errors where time period between data frames is less than 5.5 micro seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubDataRateMismatchs 1.3.6.1.4.1.298.1.3.3.1.1.10
Global counter, for this hub, of errors where incoming data rate is not with in the tolerance level of 10MHZ + or - 0.01%.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubShortEvents 1.3.6.1.4.1.298.1.3.3.1.1.11
Global counter, for this hub, of data burst where data is less than 10 bytes in length, with no SFD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubCollisions 1.3.6.1.4.1.298.1.3.3.1.1.12
Global counter of collision flags, for this hub.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubLateCollisions 1.3.6.1.4.1.298.1.3.3.1.1.13
Global counter, for this hub, of collisions occurring after the 64 byte collision window.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubMJLPs 1.3.6.1.4.1.298.1.3.3.1.1.14
Global counter of MAU jabber lockup protection where hub repeater chip goes into lockup state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubAutoPartitions 1.3.6.1.4.1.298.1.3.3.1.1.15
Global counter, for this hub, of all ports including 3in1 port being partitioned from network in response to 31 or more continuous collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubSFDMissings 1.3.6.1.4.1.298.1.3.3.1.1.16
Global counter, for this hub, of a burst of data greater than or equal to 10 bytes in length with no SFD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGlobalHubBadFrames 1.3.6.1.4.1.298.1.3.3.1.1.17
Global counter, for this hub, of total errored frame including toolong, runts, misaligned, or bad FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatisticsTable 1.3.6.1.4.1.298.1.3.3.1.3
Table of statistical information for each group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetGrpStatisticsEntry

eGrpStatisticsEntry 1.3.6.1.4.1.298.1.3.3.1.3.1
Entry for individual group in table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnetGrpStatisticsEntry  

eGrpStatIndex 1.3.6.1.4.1.298.1.3.3.1.3.1.1
The value of this object identifies the group for which this entry contains group statistical information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

eGrpStatReadableFrames 1.3.6.1.4.1.298.1.3.3.1.3.1.2
Group counter of 'good' or readable frames. Frame is between 64 and 1518 bytes in length and has SFD and good FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatMcastFrames 1.3.6.1.4.1.298.1.3.3.1.3.1.3
Group counter of number of muliticast frames. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatBcastFrames 1.3.6.1.4.1.298.1.3.3.1.3.1.4
Group counter of number of broadcast frames. All 1s in network destination address. Multicast packets are not included.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatFrameTooLongs 1.3.6.1.4.1.298.1.3.3.1.3.1.5
Group counter for data frames longer than 1518 bytes, with a SFD and good FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatRunts 1.3.6.1.4.1.298.1.3.3.1.3.1.6
Group counter for data frames with size less than 64 bytes, with no CRC or alignment errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatAlignmentErrors 1.3.6.1.4.1.298.1.3.3.1.3.1.7
Group counter of frames which are not integer multiples of 1 byte .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatFragmentErrors 1.3.6.1.4.1.298.1.3.3.1.3.1.8
Group counter of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatFCSErrors 1.3.6.1.4.1.298.1.3.3.1.3.1.9
Group counter frames that failed Cyclic Redundancy Check (CRC).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatIFGErrors 1.3.6.1.4.1.298.1.3.3.1.3.1.10
Group counter of Interframe Gap Errors where time period between data frames is less than 5.5 micro seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatDataRateMismatchs 1.3.6.1.4.1.298.1.3.3.1.3.1.11
Group counter of errors where incoming data rate is not with in the tolerance level of 10 MHZ + or - 0.01%.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatShortEvents 1.3.6.1.4.1.298.1.3.3.1.3.1.12
Group counter of data burst where data is less than 10 bytes in length, with no SFD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatCollisions 1.3.6.1.4.1.298.1.3.3.1.3.1.13
Group counter of collision flags.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatLateCollisions 1.3.6.1.4.1.298.1.3.3.1.3.1.14
Group counter of collisions occurring after the 64 byte collision window.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatMJLPs 1.3.6.1.4.1.298.1.3.3.1.3.1.15
Group counter of MAU jabber lockup protection where hub repeater chip goes into lockup state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatAutoPartitions 1.3.6.1.4.1.298.1.3.3.1.3.1.16
Group counter of ports in group autopartitioned in response to 31 or more continuous collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatSFDMissings 1.3.6.1.4.1.298.1.3.3.1.3.1.17
Group counter of a burst of data greater than or equal to 10 bytes in length with no SFD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eGrpStatBadFrames 1.3.6.1.4.1.298.1.3.3.1.3.1.18
Group counter of total errored frames including toolong, runts, misaligned, or bad FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatisticsTable 1.3.6.1.4.1.298.1.3.3.1.4
Table for port specific network statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetPortStatisticsEntry

ePortStatisticsEntry 1.3.6.1.4.1.298.1.3.3.1.4.1
Entry for individual port in table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnetPortStatisticsEntry  

ePortGrpIndex 1.3.6.1.4.1.298.1.3.3.1.4.1.1
The value of this object identifies the group for which this entry contains port statistical information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortIndex 1.3.6.1.4.1.298.1.3.3.1.4.1.2
The value of this object identifies the port for which this entry contains port statistical information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortStatReadableFrames 1.3.6.1.4.1.298.1.3.3.1.4.1.3
Port counter of good or readable frames. Frame is between 64 and 1518 bytes in length and has SFD and good FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatMcastFrames 1.3.6.1.4.1.298.1.3.3.1.4.1.4
Port counter of number of muliticast frames. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatBcastFrames 1.3.6.1.4.1.298.1.3.3.1.4.1.5
Port counter of number of broadcast frames. All 1s in network destination address. Multicast packets are not included.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatFrameTooLongs 1.3.6.1.4.1.298.1.3.3.1.4.1.6
Port counter for data frames longer than 1518 bytes, with a SFD and good FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatRunts 1.3.6.1.4.1.298.1.3.3.1.4.1.7
Port counter for data frames with size less than 64 bytes, with no CRC or alignment errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatAlignmentErrors 1.3.6.1.4.1.298.1.3.3.1.4.1.8
Port counter of frames which are not integer multiples of 1 byte.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatFragmentErrors 1.3.6.1.4.1.298.1.3.3.1.4.1.9
Port counter of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatFCSErrors 1.3.6.1.4.1.298.1.3.3.1.4.1.10
Port counter of frames that failed Cyclic Redundancy Check (CRC).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatIFGErrors 1.3.6.1.4.1.298.1.3.3.1.4.1.11
Port counter of Interframe Gap Errors where time period between data frames is less than 5.5 micro seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatDataRateMismatchs 1.3.6.1.4.1.298.1.3.3.1.4.1.12
Port counter of errors where incoming data rate is not with in the tolerance level of 10 MHZ + or - 0.01%.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatShortEvents 1.3.6.1.4.1.298.1.3.3.1.4.1.13
Port counter of data burst where data is less than 10 bytes in length, with no SFD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatCollisions 1.3.6.1.4.1.298.1.3.3.1.4.1.14
Port counter of collision flags.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatLateCollisions 1.3.6.1.4.1.298.1.3.3.1.4.1.15
Port counter of collisions occurring after the 64 byte collision window.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatMJLPs 1.3.6.1.4.1.298.1.3.3.1.4.1.16
Port counter of MAU jabber lockup protection where hub repeater chip goes into lockup state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatAutoPartitions 1.3.6.1.4.1.298.1.3.3.1.4.1.17
Port counter of number of times port was autopartitioned in response to 31 or more continuous collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatSFDMissings 1.3.6.1.4.1.298.1.3.3.1.4.1.18
Port counter of a burst of data greater than or equal to 10 bytes in length with no SFD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ePortStatBadFrames 1.3.6.1.4.1.298.1.3.3.1.4.1.19
Port counter of total errored frames including toolong, runts, misaligned, or bad FCS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eTrafficMatrixTable 1.3.6.1.4.1.298.1.3.3.1.5
Table to analyze the number of packets received through network traffic by the size of each packet.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetTrafficMatrixEntry

eTrafficMatrixEntry 1.3.6.1.4.1.298.1.3.3.1.5.1
Individual entry in matrix of packet lengths table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnetTrafficMatrixEntry  

eTrafficMatrixLength 1.3.6.1.4.1.298.1.3.3.1.5.1.1
Starting length for each range in table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

eTrafficMatrixRange 1.3.6.1.4.1.298.1.3.3.1.5.1.2
Range of packet sizes to be scanned for in network traffic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), from-1-to-63-bytes(2), from-64-to-127-bytes(3), from-128-to-255-bytes(4), from-256-to-511-bytes(5), from-512-to-767-bytes(6), from-768-to-1023-bytes(7), from-1024-to-1518-bytes(8), from-512-to-1023-bytes(9), from-65-to-511-bytes(10), exact-64-bytes(11), over-1518-bytes(12)  

eTrafficMatrixFramesCounts 1.3.6.1.4.1.298.1.3.3.1.5.1.3
Counter for number of frames received for particular range specified by the MatrixRange.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

eSpecific 1.3.6.1.4.1.298.1.3.3.1.6
OBJECT IDENTIFIER    

eSmartHubSpec 1.3.6.1.4.1.298.1.3.3.1.6.1
OBJECT IDENTIFIER    

eColGraphBar 1.3.6.1.4.1.298.1.3.3.1.6.1.1
Information on hardware LED collision graph bar.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

eUtilGraphBar 1.3.6.1.4.1.298.1.3.3.1.6.1.2
Information on hardware LED for utilization graph bar.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateTable 1.3.6.1.4.1.298.1.3.3.1.6.1.6
Network statistics for individual ports measured in Rate/Second.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetPortRateEntry

ePortRateEntry 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1
Individual entry in port rate table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  EnetPortRateEntry  

ePortRateGrpIndex 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.1
The value of this object identifies the group for which this entry contains port statistical information.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRatePortIndex 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.2
This value identifies the port for which this entry contains port statistical information.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateReadableFrames 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.3
Rate of occurrence of good or readable frames.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateMcastFrames 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.4
Rate of occurrence of number of muliticast frames. 1st bit in highest ordered bytes of destination address is set to 1. Broadcast packets are not included.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateBcastFrames 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.5
Rate of occurrence of number of broadcast frames. All 1s in network destination address. Multicast packets are not included.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateFrameTooLongs 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.6
Rate of occurrence of data frames longer than 1518 bytes, with a SFD and good FCS.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateRunts 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.7
Rate of occurrence of data frames with size less than 64 bytes, with no CRC or alignment errors.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateAlignmentErrors 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.8
Rate of occurrence of frames which are not integer multiples of 1 byte.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateFragmentErrors 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.9
Rate of occurrence of frames greater than 2 bytes and less than 64 bytes, with SFD and bad FCS (CRC error).
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateFCSErrors 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.10
Rate of occurrence of frames that failed Cyclic Redundancy Check (CRC).
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateIFGErrors 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.11
Rate of occurrence of interframe Gap Errors where time period between data frames is less than 5.5 micro seconds.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateDataRateMismatch 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.12
Rate of occurrence of errors where incoming data rate is not with in the tolerance level of 10 MHz + or - 0.01%.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateShortEvents 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.13
Rate of occurrence of data burst where data is less than 10 bytes in length, with no SFD.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateCollisions 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.14
Rate of occurrence of collision flags.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateLateCollisions 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.15
Rate of occurrence of collisions occurring after the 64 byte collision window.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateMJLPs 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.16
Rate of occurrence of MAU jabber lockup protection where hub repeater chip goes into lockup state.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateAutoPartitions 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.17
Rate of occurrence of times port was autopartitioned in response to 31 or more continuous collisions.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateSFDMissings 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.18
Rate of occurrence of a burst of data greater than or equal to 10 bytes in length with no SFD.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortRateBadFrames 1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.19
Rate of occurrence of total errored frames including toolong, runts, misaligned, or bad FCS.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortStateCtrlTable 1.3.6.1.4.1.298.1.3.4.1.1
Table for port control parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EPortStateCtrlEntry

ePortStateCtrlEntry 1.3.6.1.4.1.298.1.3.4.1.1.1
Individual entry of port control in table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EPortStateCtrlEntry  

ePortStateGrpIndex 1.3.6.1.4.1.298.1.3.4.1.1.1.1
The value of this object identifies the group for which this entry contains port control information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortStatePortIndex 1.3.6.1.4.1.298.1.3.4.1.1.1.2
This value identifies the port for which this entry contains port control information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ePortStateType 1.3.6.1.4.1.298.1.3.4.1.1.1.3
Type of cabling physically connected to port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), bNC(2), aUI(3), rJ45(4), foil(5), three-in-one(6)  

ePortStateLinkStatus 1.3.6.1.4.1.298.1.3.4.1.1.1.4
Link status for particular port. On=physical link if link test enabled. Off=no physical link exists or link test is disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER others(1), linkon(2), linkoff(3)  

ePortStateLinkIntegTest 1.3.6.1.4.1.298.1.3.4.1.1.1.5
Set can enable or disabled link integrity test. Get will say if link integrity test is enabled (2) or disabled (3).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER others(1), linkTestEnable(2), linkTestDisable(3)  

ePortStateAutoPartStatus 1.3.6.1.4.1.298.1.3.4.1.1.1.6
Whether port has been autopartitioned (2) or not autopartitioned (3).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER others(1), autopartitioned(2), notautopartitioned(3)  

ePortStateJabberStatus 1.3.6.1.4.1.298.1.3.4.1.1.1.7
Jabber detection for port. If On(2), then jabber occurred on this port. Off(3), then no jabber occurred or jabber detection has been manually disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER others(1), on(2), off(3)  

ePortStateJabberState 1.3.6.1.4.1.298.1.3.4.1.1.1.8
Set can enable or disable jabber detection test. Get will say if jabber detection test is enabled (2) or disabled (3).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER others(1), enabled(2), disabled(3)  

ePortStateAdminState 1.3.6.1.4.1.298.1.3.4.1.1.1.9
Set will manually enable or disable any port. Get will say if port has been enabled (2) or disabled (3).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER others(1), enabled(2), disabled(3)  

ePortStateRDTState 1.3.6.1.4.1.298.1.3.4.1.1.1.10
Whether RecvThreshold has been enabled or disabled. Can use this to lower noise threshold (tolerance) so that longer twisted pair links can be used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER others(1), unreduce(2), reduce(3)  

ePortStatePolarityStatus 1.3.6.1.4.1.298.1.3.4.1.1.1.11
Polarity is correct (2) or not for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER others(1), normal(2), reversed(3)  

ePortStatePolarityState 1.3.6.1.4.1.298.1.3.4.1.1.1.12
Autopolarity correction enabled or disabled. Allows hub to make electrical corrections automatically if cable does not reverse polarity within wire pairs. If do not want this correction to take place, autocorrection can be disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER others(1), enabled(2), disabled(3)  

nodeSummaryTable 1.3.6.1.4.1.298.1.3.5.1
Node summary of all traffic through hub.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NodeSummaryEntry

nodeSummaryEntry 1.3.6.1.4.1.298.1.3.5.1.1
Individual entry in node summary table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NodeSummaryEntry  

nodeSummaryGrpIndex 1.3.6.1.4.1.298.1.3.5.1.1.1
Group Id for identifying the group where node activity is detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nodeSummaryPortIndex 1.3.6.1.4.1.298.1.3.5.1.1.2
Port Id for identifying the port where node activity is detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nodeSummarySrcMacAddr 1.3.6.1.4.1.298.1.3.5.1.1.3
The source MAC address of the node that is transmitting frames received by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

nodeSummaryDestMacAddr 1.3.6.1.4.1.298.1.3.5.1.1.4
The destination MAC address of the node to which frames are being received by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

nodeSummaryEtherType 1.3.6.1.4.1.298.1.3.5.1.1.5
The 2 bytes after the source (src) address in packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nodeSummaryIpAddrPair 1.3.6.1.4.1.298.1.3.5.1.1.6
Destination and source IP address if packet is an Ethernet IP packet. It the packet is not an Ethernet IP packet, then the information may not be accurate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

nodeSummaryTimeStamp 1.3.6.1.4.1.298.1.3.5.1.1.7
nodeSummary entry time stamp (in hundredths of a second) since the network management portion of the system was last re-initialized.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

nodeSecurity 1.3.6.1.4.1.298.1.3.5.2
OBJECT IDENTIFIER    

nodeSecuLev1Table 1.3.6.1.4.1.298.1.3.5.2.1
Table of nodes which have access to particular ports. Nodes are identified by MAC address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NodeSecuLev1Entry

nodeSecuLev1Entry 1.3.6.1.4.1.298.1.3.5.2.1.1
Individual entry for node security table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NodeSecuLev1Entry  

nodeSecuLev1GrpIndex 1.3.6.1.4.1.298.1.3.5.2.1.1.1
Group ID for port which verifying node access.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nodeSecuLev1PortIndex 1.3.6.1.4.1.298.1.3.5.2.1.1.2
Specific port for which verifying node access.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nodeSecuLev1Status 1.3.6.1.4.1.298.1.3.5.2.1.1.3
Address is valid or invalid.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), invalid(3)  

nodeSecuLev1AllowedAddr 1.3.6.1.4.1.298.1.3.5.2.1.1.4
MAC address of nodes allowed for particular port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

nodeSecuLev1Action 1.3.6.1.4.1.298.1.3.5.2.1.1.5
Set action for node intrusion violation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), partition-port(2), send-trap(3), partition-port-and-send-trap(4), send-trap-and-request-page(5), partition-port-and-send-trap-and-request-page(6)  

thresholdAlarm 1.3.6.1.4.1.298.1.3.6.1
OBJECT IDENTIFIER    

thresholdLev1Table 1.3.6.1.4.1.298.1.3.6.1.1
Threshold/trap table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ThresholdLev1Entry

thresholdLev1Entry 1.3.6.1.4.1.298.1.3.6.1.1.1
Individual entry in threshold trap table.
Status: optional Access: not-accessible
OBJECT-TYPE    
  ThresholdLev1Entry  

thresholdLev1Index 1.3.6.1.4.1.298.1.3.6.1.1.1.1
An index that uniquely identifies an entry in the alarm table.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

thresholdLev1Status 1.3.6.1.4.1.298.1.3.6.1.1.1.2
Status of entry in threshold/trap table.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER other(1), valid(2), invalid(3)  

thresholdLev1Target 1.3.6.1.4.1.298.1.3.6.1.1.1.3
Set target for threshold definition. Either whole hub(2) or particular port (3).
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER other(1), hub(2), port(3)  

thresholdLev1GroupIndex 1.3.6.1.4.1.298.1.3.6.1.1.1.4
Group ID for trap set. One note--if the target is selected as hub, the group index will be ignored.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER  

thresholdLev1PortIndex 1.3.6.1.4.1.298.1.3.6.1.1.1.5
Port number for trap set. One note--if the target is selected as hub, the port index will be ignored.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER  

thresholdLev1Subject 1.3.6.1.4.1.298.1.3.6.1.1.1.6
Variable checking for in trap. These are the type of frames that a trap will be verified against.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER other(1), readable-frames(2), mcast-frames(3), bcast-frames(4), frame-too-longs(5), runts(6), alignment-errors(7), fragment-errors(8), fCS-errors(9), iFG-errors(10), data-rate-mismatch(11), short-events(12), collisions(13), late-collisions(14), auto-partitions(15), sfd-missing(16), bad-frames(17)  

thresholdLev1SampleType 1.3.6.1.4.1.298.1.3.6.1.1.1.7
The method of sampling the selected variable and calculating the value to be compared against the threshold.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER other(1), event-per-second(2)  

thresholdLev1StartupAlarm 1.3.6.1.4.1.298.1.3.6.1.1.1.8
When the trap is triggered in relation to value set. When goes above (2), below (3), or changes at all from (4).
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER other(1), rising(2), falling(3), rising-or-falling(4)  

thresholdLev1WaterMark 1.3.6.1.4.1.298.1.3.6.1.1.1.9
Counter of threshold.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER  

thresholdLev1DetectedValue 1.3.6.1.4.1.298.1.3.6.1.1.1.10
The value of the statistic for the last sampling period.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER  

thresholdLev1RisingEvent 1.3.6.1.4.1.298.1.3.6.1.1.1.11
How to respond to a triggered event for a rising event.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER other(1), partition-port(2), send-trap(3), partition-port-and-send-trap(4), send-trap-and-request-page(5), partition-port-and-send-trap-and-request-page(6)  

thresholdLev1FallingEvent 1.3.6.1.4.1.298.1.3.6.1.1.1.12
How to respond to a triggered event for a falling event.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER other(1), partition-port(2), send-trap(3), partition-port-and-send-trap(4), send-trap-and-request-page(5), partition-port-and-send-trap-and-request-page(6)  

thresholdLev1Interval 1.3.6.1.4.1.298.1.3.6.1.1.1.13
The interval in seconds over which the data is sampled.
Status: optional Access: read-write
OBJECT-TYPE    
  INTEGER  

thresholdLev1OwnerString 1.3.6.1.4.1.298.1.3.6.1.1.1.14
8-byte octet reserved for the owner who defined this entry.
Status: optional Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(8)  

adapterProductId 1.3.6.1.4.1.298.2.1
OBJECT IDENTIFIER    

concProductId 1.3.6.1.4.1.298.2.2
OBJECT IDENTIFIER    

hub1012 1.3.6.1.4.1.298.2.2.1
OBJECT IDENTIFIER    

hub1012-bridge 1.3.6.1.4.1.298.2.2.2
OBJECT IDENTIFIER    

thresholdLev1 1
The SNMP trap that is generated when an alarm entry crosses its rising threshold or falling threshold, and generates an event that is configured for sending SNMP traps.
TRAP-TYPE    

nodeSecuLevel1 2
The SNMP trap that is generated when the MAC layer address of the incoming frame from a particular port does not match the pre-assigned address with that port, and generates an event that is configured for sending SNMP traps.
TRAP-TYPE