ARUBAWIRED-VSX-MIB
File:
ARUBAWIRED-VSX-MIB.mib (19878 bytes)
Imported modules
Imported symbols
Defined Types
VidList |
|
Each octet within this value specifies a set of eight
VLAN index (VID), with the first octet specifying VIDs 1
through 8, the second octet specifying VIDs 9 through 16,
etc. Within each octet, the most significant bit represents
the lowest numbered VID, and the least significant bit
represents the highest numbered VID. Thus, each VID
is represented by a single bit within the value of this
object. If that bit has a value of 1 then that VID is
included in the set of VIDs; the VID is not included if its
bit has a value of 0. This list represents the entire
range of VLAN index values defined in the scope of IEEE
802.1Q. |
TEXTUAL-CONVENTION |
|
|
|
|
OCTET STRING |
Size(512) |
|
ArubaWiredVsxAggregatorEntry |
|
SEQUENCE |
|
|
|
|
arubaWiredVsxAggregatorIndex |
InterfaceIndex |
|
|
arubaWiredVsxAggregatorType |
INTEGER |
|
|
arubaWiredVsxVlanList |
VidList |
|
|
arubaWiredVsxLoopProtectEnabled |
TruthValue |
|
|
arubaWiredVsxLoadBalanceScheme |
INTEGER |
|
|
arubaWiredVsxCosOverride |
INTEGER |
|
|
arubaWiredVsxDscpOverride |
INTEGER |
|
|
arubaWiredVsxQoSTrust |
INTEGER |
|
Defined Values
arubaWiredVsxMIB |
1.3.6.1.4.1.47196.4.1.1.3.7 |
This is the MIB module related to HPE Aruba VSX feature |
MODULE-IDENTITY |
|
|
|
arubaWiredVsxIslPort |
1.3.6.1.4.1.47196.4.1.1.3.7.1.1.1 |
Interface name corresponding to the VSX InterSwitchLink port.
A value of 0 means there is no ISL port configuration. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
arubaWiredVsxIslHoldTime |
1.3.6.1.4.1.47196.4.1.1.3.7.1.1.3 |
ISL port-flap hold time in seconds. The default value is 0. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..3 |
|
arubaWiredVsxIslVIDList |
1.3.6.1.4.1.47196.4.1.1.3.7.1.1.8 |
VLAN IDs that the ISL port is a member of. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
VidList |
|
|
arubaWiredVsxKeepAliveUdpPort |
1.3.6.1.4.1.47196.4.1.1.3.7.1.2.4 |
The KeepAlive UDP port. Same port is used as source and destination UDP ports. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Integer32 |
1024..65535 |
|
arubaWiredVsxAggregatorEntry |
1.3.6.1.4.1.47196.4.1.1.3.7.1.3.1.1 |
The fields in this entry will be used to supplement
fields of dot3adAggEntry in ieee802.3ad mib. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
ArubaWiredVsxAggregatorEntry |
|
|
arubaWiredVsxAggregatorIndex |
1.3.6.1.4.1.47196.4.1.1.3.7.1.3.1.1.1 |
The unique identifier allocated to this Aggregator by
the local System. This attribute identifies an
Aggregator instance among the subordinate managed
objects of the containing object.
This value is read-only. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
InterfaceIndex |
|
|
arubaWiredVsxAggregatorType |
1.3.6.1.4.1.47196.4.1.1.3.7.1.3.1.1.2 |
This field specifies the aggregator/lag type. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
point2Point(1), multiChassis(2) |
|
arubaWiredVsxVlanList |
1.3.6.1.4.1.47196.4.1.1.3.7.1.3.1.1.3 |
VLANs that this aggregator is a member of. This is used for configuration consistency validation. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
VidList |
|
|
arubaWiredVsxLoopProtectEnabled |
1.3.6.1.4.1.47196.4.1.1.3.7.1.3.1.1.4 |
Loop Protect protocol admin state for this VSX. This is used for configuration consistency validation. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
arubaWiredVsxLoadBalanceScheme |
1.3.6.1.4.1.47196.4.1.1.3.7.1.3.1.1.5 |
Load balance scheme configured for this VSX. This is used for configuration consistency validation. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
l2-Src-Dst(1), l3-Src-Dst(2), l4-Src-Dst(3) |
|
arubaWiredVsxCosOverride |
1.3.6.1.4.1.47196.4.1.1.3.7.1.3.1.1.6 |
CoS override configuration for this VSX. This is used for configuration consistency validation. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..7 |
|
arubaWiredVsxDscpOverride |
1.3.6.1.4.1.47196.4.1.1.3.7.1.3.1.1.7 |
DSCP override configuration for this VSX. This is used for configuration consistency validation. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
0..63 |
|
arubaWiredVsxQoSTrust |
1.3.6.1.4.1.47196.4.1.1.3.7.1.3.1.1.8 |
Port QoS trust mode configured for this VSX. This is used for configuration consistency validation. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
cos(1), dscp(2) |
|
arubaWiredVsxDeviceRole |
1.3.6.1.4.1.47196.4.1.1.3.7.1.4.1 |
VSX device role. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
primary(1), secondary(2), notConfigured(3) |
|
arubaWiredVsxConfigSync |
1.3.6.1.4.1.47196.4.1.1.3.7.1.4.2 |
VSX config sync. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enabled(1), disabled(2) |
|
arubaWiredVsxIslOperState |
1.3.6.1.4.1.47196.4.1.1.3.7.2.1.1 |
ISL operational state. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
init(1), outSync(2), inSync(3) |
|
arubaWiredVsxIslPduTx |
1.3.6.1.4.1.47196.4.1.1.3.7.2.1.2 |
Number of ISL PDUs transmitted by this device. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
arubaWiredVsxIslPduRx |
1.3.6.1.4.1.47196.4.1.1.3.7.2.1.3 |
Number of ISL PDUs received by this device. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
arubaWiredVsxIslHelloTx |
1.3.6.1.4.1.47196.4.1.1.3.7.2.1.4 |
Number of ISL Hello packets transmitted by this device. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
arubaWiredVsxIslHelloRx |
1.3.6.1.4.1.47196.4.1.1.3.7.2.1.5 |
Number of ISL Hello packets received by this device. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
arubaWiredVsxDeviceOperSystemID |
1.3.6.1.4.1.47196.4.1.1.3.7.2.1.6 |
System identifier used by this device - derived from
system identifier values of the 2 devices. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
DisplayString |
|
|
arubaWiredVsxKeepAliveOperState |
1.3.6.1.4.1.47196.4.1.1.3.7.2.2.1 |
KeepAlive protocol operational state. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
init(1), configured(2), inSyncEstablished(3), outofSyncEstablished(4), initEstablished(5), failed(6), stopped(7) |
|
arubaWiredVsxKeepAliveTimeoutCount |
1.3.6.1.4.1.47196.4.1.1.3.7.2.2.5 |
Number of times KeepAlive protocol went to failed state because of KeepAlive timer expiry. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
arubaWiredVsxKeepAliveLastEstablishedTime |
1.3.6.1.4.1.47196.4.1.1.3.7.2.2.6 |
Stores the most recent time KeepAlive handshake was successful
and a value of 0 indicates KeepAlive handshake was never established. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeTicks |
|
|
arubaWiredVsxKeepAliveLastFailedTime |
1.3.6.1.4.1.47196.4.1.1.3.7.2.2.7 |
Stores the most recent time KeepAlive handshake failed
and a value of 0 indicates KeepAlive handshake never failed. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TimeTicks |
|
|
islUp |
1.3.6.1.4.1.47196.4.1.1.3.7.3.1.1 |
An islUp trap signifies that ISL transitioned to inSync state |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
islDown |
1.3.6.1.4.1.47196.4.1.1.3.7.3.1.2 |
An islDown trap signifies that ISL transitioned to outOfSync
state |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
keepAliveUp |
1.3.6.1.4.1.47196.4.1.1.3.7.3.1.3 |
A keepAliveUp trap signifies that KA is in established state |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|
keepAliveDown |
1.3.6.1.4.1.47196.4.1.1.3.7.3.1.4 |
A keepAliveDown trap signifies that KA is in failed state |
Status: current |
Access: read-only |
NOTIFICATION-TYPE |
|
|
|