ARUBA-TC

File: ARUBA-TC.mib (26000 bytes)

Imported modules

SNMPv2-SMI

Imported symbols

ObjectSyntax TimeTicks Integer32

Defined Types

ArubaEnableValue  
Represents a Flag which is either Enabled or Disabled.
TEXTUAL-CONVENTION    
  INTEGER enabled(1), disabled(2)  

ArubaFrameType  
Represents the Frame type.
TEXTUAL-CONVENTION    
  INTEGER associateRequest(0), associateResponse(1), reassociateRequest(2), reassociateResponse(3), probeRequest(4), probeResponse(5), beacon(8), atim(9), disassociate(10), auth(11), deauth(12)  

ArubaPhyType  
Represents the PHY-type of the access point or client. Wired clients will show 'wired' in user MIB entries.
TEXTUAL-CONVENTION    
  INTEGER dot11a(1), dot11b(2), dot11g(3), dot11ag(4), wired(5)  

ArubaHTMode  
Represents the HT status of the access point or client.
TEXTUAL-CONVENTION    
  INTEGER none(1), ht20(2), ht40(3), vht20(4), vht40(5), vht80(6), vht160(7), vht80plus80(8)  

ArubaHTExtChannel  
Represents the extension channel offset relative to the current channel.
TEXTUAL-CONVENTION    
  INTEGER none(1), above(2), below(3), eighty(4)  

ArubaMonEncryptionType  
Represents the encryption type supported by the access point.
TEXTUAL-CONVENTION    
  INTEGER open(0), wep(1), wpa(2), wpa2(3)  

ArubaMonEncryptionCipher  
Represents the WPA encryption cipher supported by the access point.
TEXTUAL-CONVENTION    
  INTEGER none(0), wep40(1), wep104(2), tkip(3), aesccmp(4), other(5)  

ArubaMonAuthAlgorithm  
Represents the WPA authentication algorithm supported by the access point.
TEXTUAL-CONVENTION    
  INTEGER none(0), psk(1), dot1x(2), other(3)  

ArubaSwitchRole  
Represents the role of the controller
TEXTUAL-CONVENTION    
  INTEGER master(1), local(2), backupmaster(3)  

ArubaSupportStatus  
Represents if a feature is supported or unsupported.
TEXTUAL-CONVENTION    
  INTEGER unsupported(1), supported(2)  

ArubaActiveState  
Represents if a feature is active or inactive.
TEXTUAL-CONVENTION    
  INTEGER active(1), inactive(2)  

ArubaACLDomain  
Represents both the source and destination to which an ACL rule will be applied.
TEXTUAL-CONVENTION    
  INTEGER alias(1), any(2), user(3), host(4), network(5)  

ArubaACLNetworkServiceType  
Represents the network service in an ACL Rule.
TEXTUAL-CONVENTION    
  INTEGER alias(1), any(2), tcp(3), udp(4), protocol(5)  

ArubaACLAction  
Represents the Actions in an ACL rule.
TEXTUAL-CONVENTION    
  INTEGER deny(1), permit(2), srcNAT(3), dstNAT(4), redirect(5)  

ArubaDaysOfWeek  
Represents the Actions in an ACL rule.
TEXTUAL-CONVENTION    
  INTEGER sun(1), mon(2), tue(3), wed(4), thu(5), fri(6), sat(7)  

ArubaAuthenticationMethods  
Authentication Method.
TEXTUAL-CONVENTION    
  INTEGER none(0), web(1), mac(2), vpn(3), dot1x(4), kerberos(5), secureId(7), pubcookie(15), xSec(16), xSecMachine(17), via-vpn(28), other(255)  

ArubaSubAuthenticationMethods  
Sub Authentication Method (e.g. EAP type).
TEXTUAL-CONVENTION    
  INTEGER authPAP(1), authCHAP(2), authMSCHAP(3), authMSCHAPv2(4), eapTLS(5), eapTTLS(6), eapLEAP(7), eapMD5(8), eapPEAP(9)  

ArubaEncryptionType  
Encryption Method.
TEXTUAL-CONVENTION    
  INTEGER none(0), static-wep(1), dynamic-wep(2), wpa-psk-tkip(3), wpa-tkip(4), wpa-psk-aes(5), wpa-aes(6), wpa2-psk-tkip(7), wpa2-tkip(8), wpa2-psk-aes(9), wpa2-aes(10), xSec(11), bSec-128(12), bSec-256(13), aes-128-cmac(14), unknown(15)  

ArubaUserForwardMode  
User Forwarding Mode.
TEXTUAL-CONVENTION    
  INTEGER tunnel-encrypted(0), bridge(1), tunnel-decrypted(2), split-tunnel(3)  

ArubaRogueApType  
Represents the Rogue AP Type.
TEXTUAL-CONVENTION    
  INTEGER valid(1), interfering(2), unsecure(3), dos(4), unknown(5), knownInterfering(6), suspectedUnsecure(7)  

ArubaAPMatchType  
Represents the match type of a suspected rogue AP.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), configuredWiredMac(1), ethernetWiredMac(2), apWiredMac(3), externalWiredMac(4), manual(5), baseBSSIDOverride(6), mms(7), ethernetGatewayWiredMac(8), classificationDisabled(9), apBSSID(10), propagatedEthernetWiredMac(11), apRule(12), systemWiredMac(13), systemGatewayMac(14)  

ArubaAPMatchMethod  
Represents the match method of a suspected rogue AP.
TEXTUAL-CONVENTION    
  INTEGER notApplicable(0), exactMatch(1), plusOneMatch(2), minusOneMatch(3), ouiMatch(4)  

ArubaStationType  
Represents the station type.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), valid(1), interfering(2), dos(3)  

ArubaEncryptionMethods  
Represents the Actions in an ACL rule.
TEXTUAL-CONVENTION    
  BITS disabled(0), static-wep(1), dynamic-wep(2), static-wpa(3), dynamic-wpa(4), wpa2-psk-aes(5), wpa2-8021x-aes(6), wpa2PreAuth(7), xsec(8), wpa-psk-aes(9), wpa-aes(10), wpa2-psk-tkip(11), wpa2-8021x-tkip(12)  

ArubaHashAlgorithms  
Represents the Actions in an ACL rule.
TEXTUAL-CONVENTION    
  INTEGER md5(1), sha(2)  

ArubaVlanValidRange  
Represents the Valid Vlan Id Range.
TEXTUAL-CONVENTION    
  INTEGER 1..4095  

ArubaPortMode  
Represents the controller port mode.
TEXTUAL-CONVENTION    
  INTEGER access(1), dot1q(2)  

ArubaDot1dState  
Represents the controller port spanning tree state.
TEXTUAL-CONVENTION    
  INTEGER disabled(1), blocked(2), listening(3), learning(4), forwarding(5)  

ArubaAPDot1dState  
Represents the AP port spanning tree state.
TEXTUAL-CONVENTION    
  INTEGER notAvailable(1), off(2), disabled(3), listening(4), learning(5), forwarding(6), blocking(7)  

ArubaPoeState  
Represents the POE mode.
TEXTUAL-CONVENTION    
  INTEGER disabled(1), enabled(2), enabledCisco(3), notAvailable(4)  

ArubaCardType  
Type of the hardware module.
TEXTUAL-CONVENTION    
  INTEGER lc1(1), lc2(2), sc1(3), sc2(4), sw2400(5), sw800(6), sw200(7), m3mk1(8), sw3200(9), sw3400(10), sw3600(11), sw650(12), sw651(13), reserved1(14), reserved2(15), sw620(16), sw7210(17), sw7220(18), sw7240(19), sw3500(20), sw2500(21), sw1500(22), sw7010(23), sw7005(24), sw7030(25), sw7110(26)  

ArubaESIServerMode  
The mode of the ESI server.
TEXTUAL-CONVENTION    
  INTEGER bridged(1), routed(2), nat(3)  

ArubaESIServerStatus  
The status of the ESI server.
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2)  

ArubaIfType  
The type of interface referred to by the value of ifIndex.
TEXTUAL-CONVENTION    
  INTEGER port(1), vlan(2), tunnel(3), loopback(4)  

ArubaVoipProtocolType  
The type of VoIP protocols supported.
TEXTUAL-CONVENTION    
  INTEGER sccp(1), svp(2), vocera(3), sip(9), ua(11), h323(13), unknown(15)  

ArubaAccessPointMode  
The mode of the access point.
TEXTUAL-CONVENTION    
  INTEGER airMonitor(1), accessPoint(2), accessPointAndMonitor(3), meshPortal(4), meshPoint(5), rfprotectSensor(6), spectrumSensor(7)  

ArubaAuthServerType  
The type of the auth server.
TEXTUAL-CONVENTION    
  INTEGER internaldb(1), radius(2), ldap(3), kerberos(4), tacacs(5)  

ArubaAddressType  
Address Type.
TEXTUAL-CONVENTION    
  INTEGER srcAddress(1), dstAddress(2), bssid(3)  

ArubaBlackListReason  
Black List Reason.
TEXTUAL-CONVENTION    
  INTEGER userDefined(1), mitmAttack(2), authFailure(3), pingFlood(4), sessionFlood(5), synFlood(6), sessionBlacklist(7), ipSpoofing(8), esiBlacklist(9), other(100)  

ArubaDBType  
DataBase Type.
TEXTUAL-CONVENTION    
  INTEGER mssql(1), mysql(2)  

ArubaVrrpState  
DataBase Type.
TEXTUAL-CONVENTION    
  INTEGER initialize(1), backup(2), master(3)  

ArubaOperStateValue  
Represents Operational state of an interface.
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2), testing(3)  

ArubaAntennaSetting  
Represents the status of the external antenna.
TEXTUAL-CONVENTION    
  INTEGER notPresent(1), enabled(2), disabled(3)  

ArubaAPStatus  
The status of the access point.
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2)  

ArubaPortSpeed  
Port Speed.
TEXTUAL-CONVENTION    
  INTEGER speed10Mbps(1), speed100Mbps(2), speed1000Mbps(3), speedAuto(4), speed10Gbps(5)  

ArubaPortDuplex  
Port Duplexity.
TEXTUAL-CONVENTION    
  INTEGER half(1), full(2), auto(3)  

ArubaPortType  
Port Type.
TEXTUAL-CONVENTION    
  INTEGER fastethernet(1), gigabitethernet(2), xgigabitethernet(3)  

ArubaEnet1Mode  
Represents the Mode of the Ethernet port on the Access Point
TEXTUAL-CONVENTION    
  INTEGER activeStandby(1), tunnel(2), bridge(3), notApplicable(4), split(5)  

ArubaUnprovisionedStatus  
Represents whether the AP is provisioned or not.
TEXTUAL-CONVENTION    
  INTEGER yes(1), no(2)  

ArubaMonitorMode  
Represents whether the AP has any radios dedicated to monitoring.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), all(1), none(2), mixed(3)  

ArubaConfigurationState  
Configuration Transfer Types.
TEXTUAL-CONVENTION    
  INTEGER success(1), error(2)  

ArubaConfigurationChangeType  
Configuration Change Types.
TEXTUAL-CONVENTION    
  INTEGER create(1), delete(2), modify(3)  

ArubaCallStates  
The Call state.
TEXTUAL-CONVENTION    
  INTEGER idle(0), initiated(1), connecting(2), delivered(3), connected(4), offered(5), alerting(6), releasing(7), cancelling(8), challenging(9), transient(10), blockwait(11), succ(12), fail(13), aborted(14), blocked(15)  

ArubaVoipProtocol  
VoIP protocol used
TEXTUAL-CONVENTION    
  INTEGER sccp(1), svp(2), vocera(3), sip(9), ua(11), h323(13)  

ArubaVoipRegState  
VoIP registered state
TEXTUAL-CONVENTION    
  INTEGER unknown(0), registering(1), unregistering(2), challenge(3), registered(4), unregistered(5)  

ArubaVoiceCdrDirection  
VoIP CDR direction
TEXTUAL-CONVENTION    
  INTEGER og(0), ic(1)  

ArubaVoiceCacBit  
Voice CAC bit flags
TEXTUAL-CONVENTION    
  BITS cacActiveLoadBalancing(0), cacHighCapThresholdReached(1), cacHandRsrvThresholdReached(2), cacPeakCapacityReached(3)  

ArubaMeshRole  
Mesh role
TEXTUAL-CONVENTION    
  INTEGER nonmesh(0), point(1), portal(2)  

ArubaHTRate  
Represents HT rate
TEXTUAL-CONVENTION    
  INTEGER unknown(0), ht6dot5(1), ht13(2), ht13dot5(3), ht15(4), ht19dot5(5), ht26(6), ht27(7), ht30(8), ht39(9), ht40dot5(10), ht45(11), ht52(12), ht54(13), ht58dot5(14), ht60(15), ht65(16), ht78(17), ht81(18), ht90(19), ht104(20), ht108(21), ht117(22), ht120(23), ht121dot5(24), ht130(25), ht135(26), ht150(27), ht162(28), ht180(29), ht216(30), ht240(31), ht243(32), ht270(33), ht300(34)  

ArubaARMChangeReason  
The reason for ARM based change.
TEXTUAL-CONVENTION    
  INTEGER radarDetected(1), radarCleared(2), txHang(3), txHangClear(4), fortyMhzIntol(5), cancel40mhzIntol(6), fortyMhzAlign(7), armInterference(8), armInvalidCh(9), armErrorThresh(10), armNoiseThresh(11), armEmptyCh(12), armRogueCont(13), armDecreasePower(14), armIncreasePower(15), armTurnOffRadio(16), armTurnOnRadio(17), armChannelQualityThresh(18)  

ArubaAPMasterStatus  
AP status as seen by the master controller (used to indicate a status change).
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2), move(3)  

ArubaDot3azStatus  
Represents the state of Energy Efficient Ethernet (802.3az).
TEXTUAL-CONVENTION    
  BITS disabled(0), unsupported(1), eee100BaseTX(2), eee1000BaseT(3), eee10GBaseT(4), eee1000BaseKX(5), eee10GBaseKX4(6), eee10GBaseKR(7)  

ArubaThresholdResourceType  
Represents the Threshold Resource Types
TEXTUAL-CONVENTION    
  INTEGER dataPathCpu(0), controlPathCpu(1), controlPathMemory(2), totalTunnelCapacity(3), userCapacity(4), noofAps(5), noofLocals(6)  

ArubaStackState  
The state of the stack element in the stack. primary - the stack element is in primary state. secondary - the stack element is in secondary state. linecard - the stack element is in linecard state. away - the stack element is in inactive state. primary, secondary and linecard implies active state of the stack element.
TEXTUAL-CONVENTION    
  INTEGER primary(1), secondary(2), linecard(3), away(4)  

ArubaStackChangeEvent  
Used to specify the event which caused change in topology in stack.
TEXTUAL-CONVENTION    
  INTEGER other(1), primarySlotChanged(2), secondarySlotChanged(3), lineCardSlotChanged(4), roleChanged(5), priorityChanged(6), versionMismatch(7), slotExceeded(8)  

ArubaStackIfTopoJoined  
Used to specify whether an interface has joined the stacking topology or left the topology.
TEXTUAL-CONVENTION    
  INTEGER connected(1), disconnected(2)  

InterfaceIndex  
A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
TEXTUAL-CONVENTION    
  Integer32 1..2147483647  

ArubaIfState  
Used to specify the state of an interface. linkUp - Operational state of this interface is up. linkDown - Operational state of this interface is down.
TEXTUAL-CONVENTION    
  INTEGER linkUp(1), linkDown(2)  

ArubaIfStateChangeReason  
Used to specify the reason for interface state change. admin - User has explicitly issued 'shutdown' or 'no shutdown' configuration from CLI on this interface. loopProtect - If ifState of an interface changes to linkDown, then it is used to specify that a loop has been detected on this interface by loop protect mechanism. If ifState of an interface changes to linkUp, then it is used to specify that loop-protect error has been cleared out on this interface through port auto-recovery mechanism or through explicit clear error-recovery command. macLimit - If ifState of an interface changes to linkDown, then it is used to specify that number of learnt MACs on this interface exceeds the limit configured. If ifState of an interface changes to linkUp, then it is used to specify that mac-limit error has been cleared out on this interface through port auto-recovery mechanism or through explicit clear error-recovery command. raGuard - If ifState of an interface changes to linkDown, then it is used to specify that invalid router advertisement has been identified on this interface, resulting shutting down of this interface. If ifState of an interface changes to linkUp, then it is used to specify that raGuard error has been cleared out on this interface through port auto-recovery mechanism or through explicit clear error-recovery command. bpduGuard - If ifState of an interface changes to linkDown, then it is used to specify that BPDU is received on this interface resulting shutting down of this interface. If ifState of an interface changes to linkUp, then it is used to specify that BPDU Guard error has been cleared out on this interface through port auto-recovery mechanism or through explicit clear error-recovery command.
TEXTUAL-CONVENTION    
  INTEGER admin(1), loopProtect(2), macLimit(3), raGuard(4), bpduGuard(5)  

ArubaAPUplinkType  
AP uplink type
TEXTUAL-CONVENTION    
  INTEGER ethernet(1), usb(2), pppoe(3), wifi(4)  

ArubaAPUplinkChangeReason  
Used to specify the reason for AP uplink change. linkFailure - The uplink went down vpnFailure - VPN tunnel could not be sustained using the uplink preemption - The uplink was pre-empted by a higher-priority uplink
TEXTUAL-CONVENTION    
  INTEGER linkFailure(1), vpnFailure(2), preemption(3)  

ArubaPortalServerDownReason  
Used to specify the reason for Portal server down. connectFail - Connect Portal server fail
TEXTUAL-CONVENTION    
  INTEGER connectFail(1)  

ArubaHaRole  
Represents the HA role of the Aruba controller
TEXTUAL-CONVENTION    
  INTEGER dual(0), active(1), standby(2), disabled(3)  

ArubaHaConnectivityStatus  
Represents the HA standby connectivity status of the Access Point
TEXTUAL-CONVENTION    
  INTEGER haSuccess(0), haNetUnreach(1), haCpUnreach(2), haImageMissMatch(3), haApDenied(4), haHbtFailure(5), haInvalidHelloResponse(6), haStandbyTunnelDown(7)  

ArubaFlexRadioMode  
Flex Radio Operating Mode
TEXTUAL-CONVENTION    
  INTEGER single2GHzBand(0), single5GHzBand(1), dual2GHzplus5GHzBand(2), unknown(3), notApplicable(4)