AMTEC-MIB

File: AMTEC-MIB.mib (262352 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI RFC-1215
SNMPv2-TC

Imported symbols

enterprises OBJECT-TYPE Gauge
Counter TimeTicks IpAddress
Counter32 Gauge32 TRAP-TYPE
DisplayString

Defined Types

SwRamEntry  
SEQUENCE    
  ramPartIndex INTEGER
  ramSizeBuf INTEGER 0..65535
  ramBufTot INTEGER 0..65535
  ramBufFreeMin INTEGER 0..65535
  ramBufFreeMax INTEGER 0..65535
  ramBufFreeNow INTEGER 0..65535

SysIfcEntry  
SEQUENCE    
  ifcProtIndex INTEGER
  ifcType INTEGER
  ifcProtCnf OCTET STRING

PhysSerOpEntry  
SEQUENCE    
  physSerOpIndex INTEGER
  physSerDsr INTEGER
  physSerCts INTEGER
  physSerDcd INTEGER
  physSerDtr INTEGER
  physSerRts INTEGER

SysSecurCertEntry  
SEQUENCE    
  sysSecurCertIndex INTEGER
  sysSecurCertState INTEGER
  sysSecurCertComNam DisplayString
  sysSecurCertSerNum DisplayString
  sysSecurCertDataScad DisplayString
  sysSecurFailedProc INTEGER

X25CnfEntry  
SEQUENCE    
  x25CnfIfc INTEGER
  x25CnfSec INTEGER
  x25CnfMode INTEGER
  x25CnfX121 DisplayString
  x25CnfPvc INTEGER
  x25CnfOvc INTEGER
  x25CnfBsvc INTEGER
  x25CnfIvc INTEGER
  x25CnfPSizeTx INTEGER
  x25CnfPSizeRx INTEGER
  x25CnfWSize INTEGER
  x25CnfModule INTEGER
  x25CnfCrin INTEGER
  x25CnfLenCrin INTEGER
  x25CnfBckIfc INTEGER
  x25CnfBckMode INTEGER

X25OpEntry  
SEQUENCE    
  x25OpIfc INTEGER
  x25OpState INTEGER
  x25OpCvAct Counter
  x25OpPckTx Counter
  x25OpPckRx Counter
  x25OpBckNum Counter
  x25OpBckState INTEGER
  x25OpBckTime TimeTicks

X25CvEntry  
SEQUENCE    
  x25CvIfcInd INTEGER
  x25CvLcgnLcn INTEGER
  x25CvState INTEGER
  x25CvType INTEGER
  x25CvTimeAct TimeTicks
  x25CvPktSizeTx INTEGER
  x25CvPktSizeRx INTEGER
  x25CvWSize INTEGER
  x25CvCalling DisplayString
  x25CvCalled DisplayString
  x25CvProtId DisplayString
  x25CvIfcApplDest INTEGER
  x25CvPktTx Counter
  x25CvPktRx Counter
  x25CvResTx Counter
  x25CvReiRx Counter
  x25CvLastResTxRx INTEGER
  x25CvCauseLastRes INTEGER
  x25CvDiagLastRes INTEGER

X25CvClrEntry  
SEQUENCE    
  x25CvClrIfcInd INTEGER
  x25CvClrInd INTEGER
  x25CvTimeEst TimeTicks
  x25CvTimeClr TimeTicks
  x25CvLcnLcgn INTEGER
  x25CvLastClrDir INTEGER
  x25CvLastClrDir INTEGER
  x25CvClrCause INTEGER
  x25CvClrDiag INTEGER
  x25CvClrCalling OCTET STRING
  x25CvClrCalled OCTET STRING
  x25CvClrProtId OCTET STRING

X25RoutEntry  
SEQUENCE    
  x25RoutInd INTEGER
  x25RoutIfcSource INTEGER
  x25RoutAddrSource DisplayString
  x25RoutIfcDest INTEGER
  x25RoutLinkDest INTEGER

X25PvcEntry  
SEQUENCE    
  x25PvcInd INTEGER
  x25PvcIfcSource INTEGER
  x25PvcPvcSource INTEGER
  x25PvcIfcDest INTEGER
  x25PvcPvcDest INTEGER

AgendaEntry  
SEQUENCE    
  x25AgIndex INTEGER
  x25AgNua INTEGER
  x25AgCypher INTEGER
  x25AgChain INTEGER
  x25AgIntegr INTEGER
  x25AgSignt INTEGER
  x25AgAuth INTEGER
  x25AgAccessctrl INTEGER
  x25AgAuthintv TimeTicks

LapbCnfEntry  
SEQUENCE    
  lapbCnfIfc INTEGER
  lapbType INTEGER
  lapbModule INTEGER
  lapbN1 INTEGER
  lapbK INTEGER
  lapbN2 INTEGER
  lapbT1 INTEGER

AdslAturPhysEntry  
SEQUENCE    
  adslAturifIndex INTEGER
  adslAturIndex INTEGER
  adslAturInvSerialNumber OCTET STRING
  adslAturInvVendorID OCTET STRING
  adslAturInvVersionNumber OCTET STRING
  adslAturCurrSnrMgn INTEGER
  adslAturCurrAtn Gauge32
  adslAturCurrStatus INTEGER
  adslAturCurrOutputPwr INTEGER
  adslAturCurrAttainableRate Gauge

AdslAtucPhysEntry  
SEQUENCE    
  adslAtucifIndex INTEGER
  adslAtucIndex INTEGER
  adslAtucInvVendorID OCTET STRING
  adslAtucInvVersionNumber OCTET STRING
  adslAtucCurrStatus INTEGER
  adslAtucCurrOutputPwr INTEGER
  adslAtucCurrAttainableRate Gauge

AdslAturChanEntry  
SEQUENCE    
  adslAturChanIfIndex INTEGER
  adslAturChanIndex INTEGER
  adslAturChanCurrTxRate Gauge32
  adslAturChanCorrectedBlks Counter32
  adslAturChanUncorrectBlks Counter32
  adslAturChanReceivedCells Counter32
  adslAturChanTransmittedCells Counter32

AdslAtucChanEntry  
SEQUENCE    
  adslAtucChanIfIndex INTEGER
  adslAtucChanIndex INTEGER
  adslAtucChanCurrTxRate Gauge32
  adslAtucChanCorrectedBlks Counter32
  adslAtucChanUncorrectBlks Counter32

AtmPvcEntry  
SEQUENCE    
  atmifIndex INTEGER
  atmpvcIndex INTEGER
  atmPvc INTEGER
  atmVpi INTEGER
  atmVci INTEGER
  atmVccAalType DisplayString Size(0..255)
  atmVccMode DisplayString Size(0..255)
  atmAalEncapsType DisplayString Size(0..255)
  atmPvcSpeed Counter
  atmPvcInOctets Counter
  atmPvcUcastPkts Counter
  atmPvcNUcastPkts Counter
  atmPvcDiscards Counter
  atmPvcErrors Counter
  atmPvcUnknownProtos Counter
  atmPvcOutOctets Counter
  atmPvcOutUcastPkts Counter
  atmPvcOutNUcastPkts Counter
  atmPvcOutDiscards Counter
  atmPvcOutErrors Counter

LapbOpEntry  
SEQUENCE    
  lapbOpIfc INTEGER
  lapbOpState INTEGER
  lapbNRejTx Counter
  lapbNRejRx Counter
  lapbNRitr Counter
  lapbNFrmrTx Counter
  lapbNFrmrRx Counter
  lapbNIframeTx Counter
  lapbNIframeRx Counter
  lapbNRRTx Counter
  lapbNRRRx Counter
  lapbNRNRTx Counter
  lapbNRNRRx Counter
  lapbNNsErr Counter

LapdCnfEntry  
SEQUENCE    
  lapdCnfIfc INTEGER
  lapdCnfTeiSapi INTEGER
  lapdCnfN200 INTEGER
  lapdCnfN201 INTEGER
  lapdCnfT200 INTEGER
  lapdCnfT203 INTEGER
  lapdCnfK INTEGER

LapdOpEntry  
SEQUENCE    
  lapdOpIfc INTEGER
  lapdOpTeiSapi INTEGER
  lapdOpState INTEGER
  lapdOpNRejTx Counter
  lapdOpNRejRx Counter
  lapdOpNRitr Counter
  lapdOpNFrmrTx Counter
  lapdOpNFrmrRx Counter
  lapdOpNIframeTx Counter
  lapdOpNIframeRx Counter
  lapdOpNRrTx Counter
  lapdOpNRrRx Counter
  lapdOpNRnrTx Counter
  lapdOpNRnrRx Counter
  lapdOpNsErr Counter
  lapdOpNUiTx Counter
  lapdOpNUiRx Counter

Q931OpEntry  
SEQUENCE    
  q931OpIfc INTEGER
  q931OpState INTEGER
  q931LastCalled DisplayString
  q931LastCalling DisplayString
  q931LastCauseDisc INTEGER

IpIfcCnfEntry  
SEQUENCE    
  ipIfcCnfInd INTEGER
  ipIfcAddress IpAddress
  ipMask IpAddress
  ipIdleTmo Gauge
  ipMtu Gauge
  ipRedirect INTEGER

IpRouteEntry  
SEQUENCE    
  ipRouteTabIfc INTEGER
  ipRouteTabGtw IpAddress
  ipRouteTabPkTx Counter
  ipRouteTabPkRx Counter
  ipRouteTabPSW INTEGER
  ipRouteTabTime TimeTicks

IpDiagAlInternEntry  
SEQUENCE    
  ipDiagAlInternIndex INTEGER
  ipDiagAlInternPermDenFlag INTEGER
  ipDiagAlInternIpSrc IpAddress
  ipDiagAlInternMaskSrc IpAddress
  ipDiagAlInternIpDest IpAddress
  ipDiagAlInternMaskDst IpAddress
  ipDiagAlInternIfc INTEGER
  ipDiagAlInternTcpProt INTEGER
  ipDiagAlInternTcpPort INTEGER
  ipDiagAlInternPConnSt INTEGER
  ipDiagAlInternUdpProt INTEGER
  ipDiagAlInternUdpPort INTEGER
  ipDiagAlInternIcmpProt INTEGER
  ipDiagAlInternAhProt INTEGER
  ipDiagAlInternEspProt INTEGER

IpDiagAlRouteEntry  
SEQUENCE    
  ipDiagAlRouteIndex INTEGER
  ipDiagAlRoutePermDenFlag INTEGER
  ipDiagAlRouteIpSrc IpAddress
  ipDiagAlRouteMaskSrc IpAddress
  ipDiagAlRouteIpDest IpAddress
  ipDiagAlRouteMaskDst IpAddress
  ipDiagAlRouteIfc INTEGER
  ipDiagAlRouteTcpProt INTEGER
  ipDiagAlRouteTcpPort INTEGER
  ipDiagAlRoutePConnSt INTEGER
  ipDiagAlRouteUdpProt INTEGER
  ipDiagAlRouteUdpPort INTEGER
  ipDiagAlRouteIcmpProt INTEGER
  ipDiagAlRouteAhProt INTEGER
  ipDiagAlRouteEspProt INTEGER

IpSecTcEntry  
SEQUENCE    
  ipSecTcGtw IpAddress
  ipSecTcCypher INTEGER
  ipSecTcChain INTEGER
  ipSecTcIntegr INTEGER
  ipSecTcSignt INTEGER
  ipSecTcAuth INTEGER
  ipSecTcAccessctrl INTEGER
  ipSecTcAuthStatus INTEGER
  ipSecTcAuthTaut INTEGER
  ipSecTcAuthTmax INTEGER
  ipSecTcAuthNmax INTEGER

IpSecTcFlashEntry  
SEQUENCE    
  ipSecTcFlashGtw IpAddress
  ipSecTcFlashCypher INTEGER
  ipSecTcFlashChain INTEGER
  ipSecTcFlashIntegr INTEGER
  ipSecTcFlashSignt INTEGER
  ipSecTcFlashAuth INTEGER
  ipSecTcFlashAccessctrl INTEGER
  ipSecTcFlashNotaio IpAddress
  ipSecTcFlashValiditySince DisplayString
  ipSecTcFlashValidityUntil DisplayString
  ipSecTcFlashInfo DisplayString

IpSecTcIpEntry  
SEQUENCE    
  ipSecTcIpIpDst IpAddress
  ipSecTcIpMaskDst IpAddress
  ipSecTcIpGtwDst IpAddress

I802IfcCnfEntry  
SEQUENCE    
  i802IfcCnfInd INTEGER
  i802IfcNLink INTEGER
  i802IfcCrin INTEGER
  i802IfcLenCrin INTEGER

I802LinkCnfEntry  
SEQUENCE    
  i802LinkIfc INTEGER
  i802LinkInd INTEGER
  i802LinkT200 INTEGER
  i802LinkTmng INTEGER
  i802LinkT203 INTEGER
  i802LinkN200 INTEGER
  i802LinkN201 INTEGER
  i802LinkK INTEGER
  i802LinkEthDst OCTET STRING
  i802LinkEthSrc OCTET STRING
  i802LinkNuaDst OCTET STRING
  i802LinkSsap INTEGER
  i802LinkDsap INTEGER

I802OpEntry  
SEQUENCE    
  i802OpIfc INTEGER
  i802OpLink INTEGER
  i802OpLanMode INTEGER
  i802OpLanState INTEGER
  i802OpWanState INTEGER
  i802OpIdbIdnRx OCTET STRING
  i802OpIdbIdnTx OCTET STRING

I802StatEntry  
SEQUENCE    
  i802StatIfc INTEGER
  i802StatLink INTEGER
  i802InfoTx Counter
  i802RnrTx Counter
  i802RejTx Counter
  i802SabmeTx Counter
  i802DiscTx Counter
  i802XidTx Counter
  i802TestTx Counter
  i802UiTx Counter
  i802FrmrTx Counter
  i802RnrTxTime TimeTicks
  i802NRitr Counter
  i802InfoRx Counter
  i802RnrRx Counter
  i802RejRx Counter
  i802SabmeRx Counter
  i802DiscRx Counter
  i802XidRx Counter
  i802TestRx Counter
  i802UiRx Counter
  i802FrmrRx Counter
  i802RnrRxTime TimeTicks

X28CnfEntry  
SEQUENCE    
  x28CnfIfc INTEGER
  x28CnfPar1 INTEGER
  x28CnfPar2 INTEGER
  x28CnfPar3 INTEGER
  x28CnfPar4 INTEGER
  x28CnfPar5 INTEGER
  x28CnfPar6 INTEGER
  x28CnfPar7 INTEGER
  x28CnfPar8 INTEGER
  x28CnfPar9 INTEGER
  x28CnfPar10 INTEGER
  x28CnfPar11 INTEGER
  x28CnfPar12 INTEGER
  x28CnfPar13 INTEGER
  x28CnfPar14 INTEGER
  x28CnfPar15 INTEGER
  x28CnfPar16 INTEGER
  x28CnfPar17 INTEGER
  x28CnfPar18 INTEGER
  x28CnfPar19 INTEGER
  x28CnfPar20 INTEGER
  x28CnfPar21 INTEGER
  x28CnfPar22 INTEGER
  x28CnfParity INTEGER

X28OpEntry  
SEQUENCE    
  x28OpIfc INTEGER
  x28OpPar1 INTEGER
  x28OpPar2 INTEGER
  x28OpPar3 INTEGER
  x28OpPar4 INTEGER
  x28OpPar5 INTEGER
  x28OpPar6 INTEGER
  x28OpPar7 INTEGER
  x28OpPar8 INTEGER
  x28OpPar9 INTEGER
  x28OpPar10 INTEGER
  x28OpPar11 INTEGER
  x28OpPar12 INTEGER
  x28OpPar13 INTEGER
  x28OpPar14 INTEGER
  x28OpPar15 INTEGER
  x28OpPar16 INTEGER
  x28OpPar17 INTEGER
  x28OpPar18 INTEGER
  x28OpPar19 INTEGER
  x28OpPar20 INTEGER
  x28OpPar21 INTEGER
  x28OpPar22 INTEGER
  x28OpParity INTEGER
  x28OpState INTEGER
  x28OpParityErr Counter
  x28OpIfcDest INTEGER

FrDlcmiEntry  
SEQUENCE    
  frDlcmiIfIndex INTEGER
  frDlcmiState INTEGER
  frDlcmiAddress INTEGER
  frDlcmiAddressLen INTEGER
  frDlcmiPollingInterval INTEGER
  frDlcmiFullEnquiryInterval INTEGER
  frDlcmiErrorThreshold INTEGER
  frDlcmiMonitoredEvents INTEGER
  frDlcmiMaxSupportedVCs INTEGER
  frDlcmiMulticast INTEGER

FrCircuitEntry  
SEQUENCE    
  frCircuitIfIndex INTEGER
  frCircuitDlci INTEGER
  frCircuitState INTEGER
  frCircuitReceivedFECNs INTEGER
  frCircuitReceivedBECNs INTEGER
  frCircuitSentFrames INTEGER
  frCircuitSentOctets INTEGER
  frCircuitReceivedFrames INTEGER
  frCircuitReceivedOctets INTEGER
  frCircuitCreationTime INTEGER
  frCircuitLastTimeChange INTEGER
  frCircuitCommittedBurst INTEGER
  frCircuitExcessBurst INTEGER
  frCircuitThroughput INTEGER

FrErrEntry  
SEQUENCE    
  frErrIfIndex INTEGER
  frErrType INTEGER
  frErrData DisplayString
  frErrTime TimeTicks

FrDlcmiProprEntry  
SEQUENCE    
  frDlcmiPrIfIndex INTEGER
  frDlcmiPrType INTEGER
  frDlcmiPrStatus INTEGER
  frDlcmiPrModFun INTEGER
  frDlcmiPrAsyncr INTEGER
  frDlcmiPrBidir INTEGER
  frDlcmiPrBidSt INTEGER
  frDlcmiPrBidPollIntCtr INTEGER
  frDlcmiPrBidFullEnqInt INTEGER
  frDlcmiPrBidErrThres INTEGER
  frDlcmiPrBidMonEv INTEGER
  frDlcmiPrNumDlciColl INTEGER

FrCircuitProprEntry  
SEQUENCE    
  frCircPrIfIndex INTEGER
  frCircPrDlci INTEGER
  frCircPrMaxLunTrama INTEGER
  frCircPrStatoBusy INTEGER
  frCircPrVelInvio INTEGER

PppLinkStatusEntry  
SEQUENCE    
  pppLinkStatusPhysicalIndex INTEGER
  pppLinkStatusBadAddresses Counter
  pppLinkStatusBadControls Counter
  pppLinkStatusPacketTooLongs Counter
  pppLinkStatusBadFCSs Counter
  pppLinkStatusLocalMRU INTEGER
  pppLinkStatusRemoteMRU INTEGER
  pppLinkStatusLocalToPeerACCMap OCTET STRING
  pppLinkStatusPeerToLocalACCMap OCTET STRING
  pppLinkStatusLocalToRemoteProtocolCompression INTEGER
  pppLinkStatusRemoteToLocalProtocolCompression INTEGER
  pppLinkStatusLocalToRemoteACCompression INTEGER
  pppLinkStatusRemoteToLocalACCompression INTEGER
  pppLinkStatusTransmitFcsSize INTEGER
  pppLinkStatusReceiveFcsSize INTEGER

PppLinkConfigEntry  
SEQUENCE    
  pppLinkConfigInitialMRU INTEGER
  pppLinkConfigReceiveACCMap OCTET STRING
  pppLinkConfigTransmitACCMap OCTET STRING
  pppLinkConfigMagicNumber INTEGER
  pppLinkConfigFcsSize INTEGER

PppSecurityConfigEntry  
SEQUENCE    
  pppSecurityConfigLink INTEGER
  pppSecurityConfigPreference INTEGER
  pppSecurityConfigProtocol OBJECT IDENTIFIER
  pppSecurityConfigStatus INTEGER

PppSecuritySecretsEntry  
SEQUENCE    
  pppSecuritySecretsLink INTEGER
  pppSecuritySecretsIdIndex INTEGER
  pppSecuritySecretsDirection INTEGER
  pppSecuritySecretsProtocol OBJECT IDENTIFIER
  pppSecuritySecretsIdentity OCTET STRING
  pppSecuritySecretsSecret OCTET STRING
  pppSecuritySecretsStatus INTEGER

PppIpEntry  
SEQUENCE    
  pppIpOperStatus INTEGER
  pppIpLocalToRemoteCompressionProtocol INTEGER
  pppIpRemoteToLocalCompressionProtocol INTEGER
  pppIpRemoteMaxSlotId INTEGER
  pppIpLocalMaxSlotId INTEGER

PppIpConfigEntry  
SEQUENCE    
  pppIpConfigAdminStatus INTEGER
  pppIpConfigCompression INTEGER

ProfileEntry  
SEQUENCE    
  profileId INTEGER
  profileName DisplayString
  profileISDNPhone1 DisplayString
  profileISDNPhone2 DisplayString
  profileISDNPhone3 DisplayString
  profileISDNPhone4 DisplayString
  profileISDNPhone5 DisplayString
  profileGatewayIP IpAddress
  profileAutUsername DisplayString
  profileAutPassword DisplayString
  profileAutPeerUsername DisplayString
  profileAutPeerPassword DisplayString
  profileAutPAP INTEGER
  profileAutCHAP INTEGER
  profileRemoteMASK IpAddress
  profileDefault INTEGER
  profileDynamic INTEGER
  profileCallbackType INTEGER
  profileUnnumbered INTEGER
  profileCalled INTEGER
  profileCalling INTEGER
  profileDefgtw INTEGER
  profileNat INTEGER
  profileCallbackReq INTEGER
  profileCallbackAccept INTEGER
  profileRemoteMaskAuto INTEGER
  profileDynamicRemoteNet INTEGER
  profileMPP INTEGER
  profileCallbackTimer INTEGER
  profileRemoteIp IpAddress
  profileRemotePool DisplayString
  profileCounterCallIn INTEGER
  profileCounterCallOut INTEGER
  profileLastCallDirection DisplayString
  profileLastCallTimeOpen DisplayString
  profileLastCallTimeClose DisplayString
  profileStatus DisplayString

ProfileRunEntry  
SEQUENCE    
  profileIdRun INTEGER
  profileIdFather INTEGER
  profileFatherName DisplayString
  profileISDNPhoneUsed DisplayString
  profileIPGateway IpAddress
  profileNumberChannelActive INTEGER
  profileIndexChannelActive DisplayString
  profileConnectionTimeForChannel DisplayString

Defined Values

amtec 1.3.6.1.4.1.1954
OBJECT IDENTIFIER    

prodotti 1.3.6.1.4.1.1954.1
OBJECT IDENTIFIER    

sys 1.3.6.1.4.1.1954.2
OBJECT IDENTIFIER    

protocol 1.3.6.1.4.1.1954.3
OBJECT IDENTIFIER    

general-configuration 1.3.6.1.4.1.1954.4
OBJECT IDENTIFIER    

ra360a 1.3.6.1.4.1.1954.1.1
Apparato RA360A
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

ra360c 1.3.6.1.4.1.1954.1.2
Apparato RA360C
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

lwi 1.3.6.1.4.1.1954.1.3
Scheda LWI (M-PAT/R)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

ra360-m 1.3.6.1.4.1.1954.1.4
Apparato RA360/M
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

ra302-a 1.3.6.1.4.1.1954.1.5
Apparato RA302/A
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

ra302-b 1.3.6.1.4.1.1954.1.6
Apparato RA302/B
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

p302 1.3.6.1.4.1.1954.1.7
Apparato P302
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

cs860 1.3.6.1.4.1.1954.1.8
Apparato CS-860
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

ra860 1.3.6.1.4.1.1954.1.9
Apparato RA-860
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

sas860 1.3.6.1.4.1.1954.1.10
Apparato SAS860
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

sas860-enh 1.3.6.1.4.1.1954.1.11
Apparato SAS860 ENHANCED
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

hw 1.3.6.1.4.1.1954.2.1
OBJECT IDENTIFIER    

sw 1.3.6.1.4.1.1954.2.2
OBJECT IDENTIFIER    

ft 1.3.6.1.4.1.1954.2.3
OBJECT IDENTIFIER    

sysIfc 1.3.6.1.4.1.1954.2.4
OBJECT IDENTIFIER    

sysAct 1.3.6.1.4.1.1954.2.5
OBJECT IDENTIFIER    

sysSecur 1.3.6.1.4.1.1954.2.6
OBJECT IDENTIFIER    

sysCPU 1.3.6.1.4.1.1954.2.7
OBJECT IDENTIFIER    

sysLog 1.3.6.1.4.1.1954.2.8
OBJECT IDENTIFIER    

hwSNumber 1.3.6.1.4.1.1954.2.1.1
Serial number della scheda
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

hwRamSize 1.3.6.1.4.1.1954.2.1.2
Dimensione della RAM espressa in MB
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER mb4-Ram(1), mb4-Ram(2)  

swBootRel 1.3.6.1.4.1.1954.2.2.1
Release del software di BOOT
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

swUsageRel 1.3.6.1.4.1.1954.2.2.2
Release del sw applicativo operativo sulla macchina (quello attivato dal sw di boot)
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

swStatus 1.3.6.1.4.1.1954.2.2.3
Questa variabile contiene informazioni relative ai software gestisti dalla scheda, in funzione del software di boot. Viene data indicazione della presenza o meno del doppio software e per ogni sw gestito lo stato del CRC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER gestito-un-solo-SW(0), sw-appl-good-SW-rec-good(1), sw-appl-good-SW-rec-bad(2), sw-appl-bad-SW-rec-good(3)  

swLastReset 1.3.6.1.4.1.1954.2.2.4
Descrizione della causa dell'ultimo RESET della scheda
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

swPart 1.3.6.1.4.1.1954.2.2.5
OBJECT IDENTIFIER    

swPartApplSize 1.3.6.1.4.1.1954.2.2.5.1
Ampiezza della partizione riservata al SW Applicativo (principale) nella memoria permanente (flash)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

swPartRecSize 1.3.6.1.4.1.1954.2.2.5.2
Ampiezza della partizione riservata al SW di Recupero nella memoria permanente (flash)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

swPartCnfSize 1.3.6.1.4.1.1954.2.2.5.3
Ampiezza della partizione riservata alla Configura- zione nella memoria permanente (es: flash)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

swCnf 1.3.6.1.4.1.1954.2.2.6
OBJECT IDENTIFIER    

sysSwCnfType 1.3.6.1.4.1.1954.2.2.6.1
Questa variabile specifica il tipo di configurazione con cui la scheda sta operando e se questa configura- zione e' stata forzata da console (al boot tramite UART)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER di-Fabbrica(1), di-Default(2), di-Lavoro(4), di-Fabbrica-impostata-utente(9), di-Default-impostata-utente(10), di-Lavoro-impostata-utente(12)  

sysVersionCnf 1.3.6.1.4.1.1954.2.2.6.2
Questa variabile specifica la versione della configurazione con cui la scheda sta operando.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sysCommitState 1.3.6.1.4.1.1954.2.2.6.3
Questa variabile specifica lo stato di upload con commit della configurazione con cui la scheda sta operando.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sysSwCnfMD5 1.3.6.1.4.1.1954.2.2.6.4
Questa variabile specifica l'hashing della configurazione con cui la scheda sta operando.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

swRam 1.3.6.1.4.1.1954.2.2.7
OBJECT IDENTIFIER    

swRamNPart 1.3.6.1.4.1.1954.2.2.7.1
Numero delle partizioni RAM riservate al Pool Buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swRamTable 1.3.6.1.4.1.1954.2.2.7.2
Tabella delle partizioni RAM riservate al Pool di Buffers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwRamEntry

swRamEntry 1.3.6.1.4.1.1954.2.2.7.2.1
Entry tabella SwRamTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwRamEntry  

ramPartIndex 1.3.6.1.4.1.1954.2.2.7.2.1.1
E' la numerazione della partizione (INDICE) RAM per Poll di Buffer. Ha un valore compreso tra 1 e il valore della variabile SwRamNPart.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ramSizeBuf 1.3.6.1.4.1.1954.2.2.7.2.1.2
Dimensione di ogni buffer all'interno della parti- zione RAM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

ramBufTot 1.3.6.1.4.1.1954.2.2.7.2.1.3
Numero dei buffers totoli all'interno della parti- zione RAM
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

ramBufFreeMin 1.3.6.1.4.1.1954.2.2.7.2.1.4
Minumo numero di buffers liberi raggiunto. Ad ogni GET SNMP il contenuto di questa variabile viene reinizializzato.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

ramBufFreeMax 1.3.6.1.4.1.1954.2.2.7.2.1.5
Massimo numero di buffers liberi raggiunto. Ad ogni GET SNMP il contenuto di questa variabile viene reinizializzato.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

ramBufFreeNow 1.3.6.1.4.1.1954.2.2.7.2.1.6
Numero di buffers liberi correnti.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

ftconf 1.3.6.1.4.1.1954.2.3.1
OBJECT IDENTIFIER    

ftdiag 1.3.6.1.4.1.1954.2.3.2
OBJECT IDENTIFIER    

ftConfValidate 1.3.6.1.4.1.1954.2.3.1.1
E'la variabile il cui SET snmp ad un valore diverso da 0 valida le variabili che definiscono i parametri di file transfer. La Get restituisce sempre valore 0
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

ftConfIpAddr 1.3.6.1.4.1.1954.2.3.1.2
Definisce indirizzo IP dell'Host con cui effettuare il file transfer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

ftConfPathFile 1.3.6.1.4.1.1954.2.3.1.3
Definisce il percorso e il nome del file da leggere o scrivere, relativo all'Host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

ftConfRW 1.3.6.1.4.1.1954.2.3.1.4
Definisce la direzione del file transfer: - PUT per trasferire il file da Agent verso Host; - GET per trasferire il file da Host verso Agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unspecOp(0), put(1), get(2)  

ftConfObj 1.3.6.1.4.1.1954.2.3.1.5
Definisce l'oggetto del file transfer: - Software - Configurazione - Agenda
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(0), sw(1), conf(2), agenda(3)  

ftConfLen 1.3.6.1.4.1.1954.2.3.1.6
Definisce la lunghezza del file da leggere da Host. La variabile ha dunque senso solo se FtConfRW=GET
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

ftConfSecLev 1.3.6.1.4.1.1954.2.3.1.7
Definisce il livello di sicurezza dell'operazione di file transfer (parametro questo tra l'altro funzione dell'equipaggiamento hardware di una scheda) nel caso di GET del SW. Si hanno le seguenti opzioni di SET: - Direct-on-flash-use: il sw viene scritto direttamente nella partizione di memoria permanente (flash) relativa al sw in uso (quello mandato in esecuzione al boot) - On-Ram: il sw viene scritto in RAM e a FT terminato scaricato nella memoria permanente. - On-2nd-Flash: il sw viene scritto prima nella partizione di memoria riservata al sw non in esecuzione (normalmente quello di recupero) e a fine FT trasferito nella partizione di memoria permanente riservata al sw in esecuzione.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notspecified(0), direct-on-flash-use(1), on-Ram(2), on-2nd-Flash(3)  

ftDiagStatAck 1.3.6.1.4.1.1954.2.3.2.1
Questa variabile serve al Manager (SET con valore diverso da 0 ) per chiudere la sessione di FT con l'Agent. A fine FT (OK o ABORT) pertanto deve essere impostata per innescare una nuovo sessione di FT
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

ftDiagState 1.3.6.1.4.1.1954.2.3.2.2
Definisce la stato della sessione FT. Valori assunti: - FREE: stato di libero - ABORT: il FT e' terminato per errore - DONE: il FT e' terminato correttamente - IMPOSSIBLE: il FT e' terminato perche' non sono state rilevate le condizione di sicurezza (FfConfSecLev), stato questo significativo per operazione GET SW - RUNNING: il FT e' in esecuzione - ANALIZING: stato valido solo per operazione GET CONF, l'Agent effettua una analisi sintattica/semantica sul file di configurazione ricevuto. - WRITING: stato in cui si trasferisce il file da RAM->FLASH o da FLASH->FLASH (vedi FtConfSecLev), valido solo nel caso di operazione GET SW.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER free(0), abort(1), done(2), impossible(3), running(4), analizing(5), writing(6)  

ftDiagInfo 1.3.6.1.4.1.1954.2.3.2.3
E' una descrizione delle operazioni di FT, e' legato al valore assunto da FtDiagState.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ftDiagCountBlk 1.3.6.1.4.1.1954.2.3.2.4
Contatore di blocchi: trasferiti dall'Agent durante l'ope- razione PUT, ricevuti dall'Agent durante l'operazione GET
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ftDiagCountNoSeq 1.3.6.1.4.1.1954.2.3.2.5
Contatore di blocchi fuori sequenza: trasferiti dall'Agent durante l'operazione PUT, ricevuti dall'Agent durante l'operazione GET
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sysIfcNum 1.3.6.1.4.1.1954.2.4.1
Numero di interfacce presenti nella scheda (quelle descritte nella tabella SysIfcTAB). Corrisponde a ifNumber definito nella MIB-II
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sysIfcTable 1.3.6.1.4.1.1954.2.4.2
Questa tabella descrive il tipo d'interfaccia e la pila dei protocolli configurati su essa.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SysIfcEntry

sysIfcEntry 1.3.6.1.4.1.1954.2.4.2.1
Entry tabella interfacce
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SysIfcEntry  

ifcProtIndex 1.3.6.1.4.1.1954.2.4.2.1.1
Indice dell'interfaccia. Corrisponde a ifIndex definito nella MIB-II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ifcType 1.3.6.1.4.1.1954.2.4.2.1.2
Descrive il tipo d'interfaccia.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lan-ethernet-1(0), serial-1(1), bri-B1(2), bri-D(3), serial-2(4), serial-3(5), serial-4(6), lan-ethernet-2(7), lan-ethernet-3(8), lan-ethernet-4(9), compact-pci(10), lan-ethernet-5(11), bri-B2(12), bri-B(13), lan-ethernet-6(14)  

ifcProtCnf 1.3.6.1.4.1.1954.2.4.2.1.3
Vettore che riporta gli identificativi (Hex) dei protocolli configurati sull'interfaccia. ----------------------------------------------- Identificativi protocolli: ----------------------------------------------- LAPB 2 LAPD 3 I802 4 ETH 5 PPP 6 TRA 7 SDLC 8 X25 9 Q931 10 QLLC 11 LLC2 12 IP 15 ISDN 21 RIP 22 X28 23 FRAME RELAY 24
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sysPhysSerial 1.3.6.1.4.1.1954.2.4.3
OBJECT IDENTIFIER    

physSerdiag 1.3.6.1.4.1.1954.2.4.3.2
OBJECT IDENTIFIER    

physSerOpTable 1.3.6.1.4.1.1954.2.4.3.2.2
Questa tabella, relativa ad interfacce seriali fornisce indicazioni sui segnali di interfaccia
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PhysSerOpEntry

physSerOpEntry 1.3.6.1.4.1.1954.2.4.3.2.2.1
Entry tabella PhysSerOpTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PhysSerOpEntry  

physSerOpIndex 1.3.6.1.4.1.1954.2.4.3.2.2.1.1
Indice interfaccia. Corrisponde a ifIndex definito nella MIB-II
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

physSerDsr 1.3.6.1.4.1.1954.2.4.3.2.2.1.2
Stato del DSR
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dSR-OFF(0), dSR-ON(1)  

physSerCts 1.3.6.1.4.1.1954.2.4.3.2.2.1.3
Stato del CTS
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cts-OFF(0), cts-ON(1)  

physSerDcd 1.3.6.1.4.1.1954.2.4.3.2.2.1.4
Stato del DCD
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dcd-OFF(0), dcd-ON(1)  

physSerDtr 1.3.6.1.4.1.1954.2.4.3.2.2.1.5
Stato del DTR
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dtr-OFF(0), dtr-ON(1)  

physSerRts 1.3.6.1.4.1.1954.2.4.3.2.2.1.6
Stato del RTS
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER rts-OFF(0), rts-ON(1)  

sysActReset 1.3.6.1.4.1.1954.2.5.1
Il SET di questa variabile imposta un azione di reset sulla macchina
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sysWriteConf 1.3.6.1.4.1.1954.2.5.2
Il SET di questa variabile permette la scrittura della configurazione nella memoria non volatile della macchina
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sysConnConfig 1.3.6.1.4.1.1954.2.5.3
Apre il canale di comunicazione con l'applicazione di configurazione per permettere la scrittura permanente della configurazione
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER configuration-channel-close(0), configuration-channel-open(1)  

sysSecurCertTable 1.3.6.1.4.1.1954.2.6.1
Questa tabella, contiene i campi per identificare un certificato stato,nome della ca,numero seriale delcert,data di scadenza,procedure fallite
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SysSecurCertEntry

sysSecurCertEntry 1.3.6.1.4.1.1954.2.6.1.1
Entry tabella SysSecurTabCert
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SysSecurCertEntry  

sysSecurCertIndex 1.3.6.1.4.1.1954.2.6.1.1.1
indice
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sysSecurCertState 1.3.6.1.4.1.1954.2.6.1.1.2
Stato del certificato del SAS
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER certificato-assente(1), certificato-valido(2), certificato-valido-e-certificato-rinnovato(3), certificato-in-scadenza(4), certificato-non-ancora-valido(5), certificato-scaduto(6)  

sysSecurCertComNam 1.3.6.1.4.1.1954.2.6.1.1.3
nome della certification authority
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

sysSecurCertSerNum 1.3.6.1.4.1.1954.2.6.1.1.4
numero identificativo del certificato
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

sysSecurCertDataScad 1.3.6.1.4.1.1954.2.6.1.1.5
data di scadenza del certificato
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

sysSecurFailedProc 1.3.6.1.4.1.1954.2.6.1.1.6
procedure fallite
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER fallito-rinnovo(1), fallito-backup(2), fallito-backup-di-rinnovo(3)  

cPUBusy 1.3.6.1.4.1.1954.2.7.1
Valore corrente della percentuale di utilizzo della CPU.
Status: current Access: read-only
OBJECT-TYPE    
  Counter  

cPUBusyMax5 1.3.6.1.4.1.1954.2.7.2
Valore massimo della percentuale di utilizzo della CPU negli ultimi 5 minuti.
Status: current Access: read-only
OBJECT-TYPE    
  Counter  

cPUBusyAvr5 1.3.6.1.4.1.1954.2.7.3
Valore medio della percentuale di utilizzo della CPU negli ultimi 5 minuti.
Status: current Access: read-only
OBJECT-TYPE    
  Counter  

sysLogBuffer 1.3.6.1.4.1.1954.2.8.1
Attivazione con numero di buffer a disposizione dell'attivita` di SYS LOG.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sysLogLevel 1.3.6.1.4.1.1954.2.8.2
Livello di funzionamento del SYS LOG.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sysLogIpAddress 1.3.6.1.4.1.1954.2.8.3
Indirizzo IP di invio pacchetti di SYS LOG.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sysLogUdpPort 1.3.6.1.4.1.1954.2.8.4
Porta di destinazione e sorgente del pacchetto di SYS LOG.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

sysLogEraseBuffer 1.3.6.1.4.1.1954.2.8.5
Inserendo un valore diverso da zero questa variabile, il file di log viene vuotato.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sysLogTrap 1.3.6.1.4.1.1954.2.8.6
OBJECT IDENTIFIER    

sysLogTrapEnable 1.3.6.1.4.1.1954.2.8.6.1
Abilitazione della trap di riempimento buffer log.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sysLogTrapLimit 1.3.6.1.4.1.1954.2.8.6.2
Percentuale del buffer a cui va inviata la trap .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..99  

sysLogTrapBufferStatus 1.3.6.1.4.1.1954.2.8.6.3
Percentuale del buffer attuale.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sysLogBufferWarning 36869
Viene inviata nel caso in cui il buffer ha raggiunto la soglia di warning e a meta` della soglia stessa.
TRAP-TYPE    

sysLogBufferFull 36870
Viene inviata nel caso in cui il buffer e` pieno e inizia la sovrascrizione dello stesso.
TRAP-TYPE    

x25 1.3.6.1.4.1.1954.3.1
OBJECT IDENTIFIER    

lapb 1.3.6.1.4.1.1954.3.2
OBJECT IDENTIFIER    

lapd 1.3.6.1.4.1.1954.3.3
OBJECT IDENTIFIER    

q931 1.3.6.1.4.1.1954.3.4
OBJECT IDENTIFIER    

ip 1.3.6.1.4.1.1954.3.5
OBJECT IDENTIFIER    

i802-2 1.3.6.1.4.1.1954.3.6
OBJECT IDENTIFIER    

x28 1.3.6.1.4.1.1954.3.7
OBJECT IDENTIFIER    

fry 1.3.6.1.4.1.1954.3.8
OBJECT IDENTIFIER    

ppp 1.3.6.1.4.1.1954.3.9
OBJECT IDENTIFIER    

ike 1.3.6.1.4.1.1954.3.10
OBJECT IDENTIFIER    

dlsw 1.3.6.1.4.1.1954.3.11
OBJECT IDENTIFIER    

adsl 1.3.6.1.4.1.1954.3.12
OBJECT IDENTIFIER    

atm 1.3.6.1.4.1.1954.3.13
OBJECT IDENTIFIER    

dns 1.3.6.1.4.1.1954.3.14
OBJECT IDENTIFIER    

x25Diag 1.3.6.1.4.1.1954.3.1.2
OBJECT IDENTIFIER    

x25Secur 1.3.6.1.4.1.1954.3.1.3
OBJECT IDENTIFIER    

x25DiagIfc 1.3.6.1.4.1.1954.3.1.2.1
OBJECT IDENTIFIER    

x25DiagX25Rout 1.3.6.1.4.1.1954.3.1.2.2
OBJECT IDENTIFIER    

x25CnfTable 1.3.6.1.4.1.1954.3.1.2.1.1
Questa tabella contiene i parametri X25 di configurazione di una interfaccia.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    X25CnfEntry

x25CnfEntry 1.3.6.1.4.1.1954.3.1.2.1.1.1
Entry tabella X25CnfTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  X25CnfEntry  

x25CnfIfc 1.3.6.1.4.1.1954.3.1.2.1.1.1.1
Indice dell'interfaccia su cui e` configurata l'entita` X25. Questo valore coincide con quello riportato dalla variabile ifIndex della MIB-II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CnfSec 1.3.6.1.4.1.1954.3.1.2.1.1.1.2
Stabilisce se operazioni di crittazione sono abilitate o meno sulla entito X25.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

x25CnfMode 1.3.6.1.4.1.1954.3.1.2.1.1.1.3
Identifica la modalita' Dte/Dce con cui opera l'interfaccia (liv.3)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dte(0), dce(128)  

x25CnfX121 1.3.6.1.4.1.1954.3.1.2.1.1.1.4
X121 address relativo all'interfaccia. Puo' ritornare una stringa vuota se il NUA non e' stato impostato tramite configurazione.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

x25CnfPvc 1.3.6.1.4.1.1954.3.1.2.1.1.1.5
Numero dei PVC configurati sull'interfaccia.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CnfOvc 1.3.6.1.4.1.1954.3.1.2.1.1.1.6
Numero OSVC configurati sull'interfaccia.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CnfBsvc 1.3.6.1.4.1.1954.3.1.2.1.1.1.7
Numero BSVC configurati sull'interfaccia.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CnfIvc 1.3.6.1.4.1.1954.3.1.2.1.1.1.8
Numero ISVC configurati sull'interfaccia
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CnfPSizeTx 1.3.6.1.4.1.1954.3.1.2.1.1.1.9
Packet Size in trasmissione relativa alla interfaccia. Valori possibili: 128,256,512,1024.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CnfPSizeRx 1.3.6.1.4.1.1954.3.1.2.1.1.1.10
Packet Size in ricezione relativa alla interfaccia. Valori possibili: 128,256,512,1024.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CnfWSize 1.3.6.1.4.1.1954.3.1.2.1.1.1.11
Window size (1...7) relativa alla interfaccia.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CnfModule 1.3.6.1.4.1.1954.3.1.2.1.1.1.12
Modulo relativo al livello 3
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER modulo-8(0), modulo-128(64)  

x25CnfCrin 1.3.6.1.4.1.1954.3.1.2.1.1.1.13
Criterio instradamento configurato (NUALEN/SUBLEN/NONE). (vedi manuale configurazione GAIA).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER criterio-NUALEN(1), criterio-SUBLEN(2), criterio-NONE(3)  

x25CnfLenCrin 1.3.6.1.4.1.1954.3.1.2.1.1.1.14
Lunghezza utilizzata dal criterio di instradamento: Valori ammessi: 0 se X25CnfCrin = NONE, da 1...15 se X25CnfCrin = NUALEN e SUBLEN
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CnfBckIfc 1.3.6.1.4.1.1954.3.1.2.1.1.1.15
Indice SNMP (ifIndex MIB-II) della interfaccia di backup, assume valore 0 se non configurato il backup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CnfBckMode 1.3.6.1.4.1.1954.3.1.2.1.1.1.16
Modalita' di rientro dal backup (Immediata/Graduale)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER gradual-Backup(0), immediate-Backup(1)  

x25OpTable 1.3.6.1.4.1.1954.3.1.2.1.2
Questa tabella definisce i parametri OPERATIVI su una interfaccia X25.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    X25OpEntry

x25OpEntry 1.3.6.1.4.1.1954.3.1.2.1.2.1
Entry tabella X25OpTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  X25OpEntry  

x25OpIfc 1.3.6.1.4.1.1954.3.1.2.1.2.1.1
Indice SNMP (ifIndex MIB-II) dell'interfaccia X.25
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25OpState 1.3.6.1.4.1.1954.3.1.2.1.2.1.2
Stato operativo dell'interfaccia logica di livello 3
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-configured(0), not-established(1), not-ready(2), restart-req-restart-ind(3), dte-restart-req(4), ready-r1(5)  

x25OpCvAct 1.3.6.1.4.1.1954.3.1.2.1.2.1.3
Numero dei Circuiti Virtuali attivi (X25OpSate diverso da Not-Ready), ovvero la somma dei circuiti tipo PVC e SVC inpegnati in una chiamata.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

x25OpPckTx 1.3.6.1.4.1.1954.3.1.2.1.2.1.4
Contatore dei pacchetti Dati trasmessi a livello 3
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

x25OpPckRx 1.3.6.1.4.1.1954.3.1.2.1.2.1.5
Contatore dei pacchetti Dati ricevuti a livello 3
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

x25OpBckNum 1.3.6.1.4.1.1954.3.1.2.1.2.1.6
Contatore dei backup effettuati a partire dal restart dell'apparato.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

x25OpBckState 1.3.6.1.4.1.1954.3.1.2.1.2.1.7
Stato corrente del backup
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER non-operativo(0), operativo(1)  

x25OpBckTime 1.3.6.1.4.1.1954.3.1.2.1.2.1.8
Valore di sysUpTime relativo allo stato corrente del backup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

x25CvTable 1.3.6.1.4.1.1954.3.1.2.1.3
Tabella dello Stato dei C.V. ATTIVI sull'interfaccia
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    X25CvEntry

x25CvEntry 1.3.6.1.4.1.1954.3.1.2.1.3.1
Entry tabella X25CvTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  X25CvEntry  

x25CvIfcInd 1.3.6.1.4.1.1954.3.1.2.1.3.1.1
Indice dell'interfaccia X.25
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvLcgnLcn 1.3.6.1.4.1.1954.3.1.2.1.3.1.2
Indice C.V. LCGN+LCN
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvState 1.3.6.1.4.1.1954.3.1.2.1.3.1.3
Stato operativo del C.V. X25
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ready-P1(0), wait-Peer-DTE-waiting-P2-DCE-waiting-P3(1), wait-upper-DTE-waiting-P3-DCE-waiting-P2(2), call-collision-p5(3), clr-DTE-p6-CLR-DCE-p7(4), clear-request-upper-DTE-clear-request-p6(5), flow-control-ready-Data-transfer-p4-d1(6), res-DTE-d2-RES-DCE-d3(7), reset-request-upper-DTE-reset-request-d2(8), rnr-RX-sottostato-dello-stato-6(101), rnr-TX-sottostato-dello-stato-6(102), rnr-RXTX-sottostato-dello-stato-6(103)  

x25CvType 1.3.6.1.4.1.1954.3.1.2.1.3.1.4
Tipo C.V. impegnato (SVC, PVC)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER svc(0), pvc(1)  

x25CvTimeAct 1.3.6.1.4.1.1954.3.1.2.1.3.1.5
Valore di sysUpTime relativo all'attivazione del C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

x25CvPktSizeTx 1.3.6.1.4.1.1954.3.1.2.1.3.1.6
Corrente Packet Size in trasmissione, sul C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvPktSizeRx 1.3.6.1.4.1.1954.3.1.2.1.3.1.7
Corrente Packet Size in ricezione, sul C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvWSize 1.3.6.1.4.1.1954.3.1.2.1.3.1.8
Corrente Windows Size del C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvCalling 1.3.6.1.4.1.1954.3.1.2.1.3.1.9
NUA Chiamante
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

x25CvCalled 1.3.6.1.4.1.1954.3.1.2.1.3.1.10
NUA Chiamato
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

x25CvProtId 1.3.6.1.4.1.1954.3.1.2.1.3.1.11
I primi 4 BYTES del Call User Data (Protocol Identifier).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

x25CvIfcApplDest 1.3.6.1.4.1.1954.3.1.2.1.3.1.12
Indice della interfaccia (ifIndex relativo) o applicazione destinataria. Valori: >1000 = applicazione -1 = interfaccia non connessa
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER aPPLICAZIONE-IP(1020)  

x25CvPktTx 1.3.6.1.4.1.1954.3.1.2.1.3.1.13
Totale pacchetti Dati trasmessi a livello 3 sul C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

x25CvPktRx 1.3.6.1.4.1.1954.3.1.2.1.3.1.14
Totale pacchetti Dati Rx a livello 3 sul C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

x25CvResTx 1.3.6.1.4.1.1954.3.1.2.1.3.1.15
Totale pacchetti Reset trasmessi sul C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

x25CvReiRx 1.3.6.1.4.1.1954.3.1.2.1.3.1.16
Totale pacchetti Reset ricevuti sul C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

x25CvLastResTxRx 1.3.6.1.4.1.1954.3.1.2.1.3.1.17
Direzione ultimo Reset sul C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER nessun-RES(0), res-TX(1), res-RX(2)  

x25CvCauseLastRes 1.3.6.1.4.1.1954.3.1.2.1.3.1.18
Causa ultimo Reset
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvDiagLastRes 1.3.6.1.4.1.1954.3.1.2.1.3.1.19
Diagnostica ultimo Reset
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvClr 1.3.6.1.4.1.1954.3.1.2.1.4
OBJECT IDENTIFIER    

x25CvNEntryReq 1.3.6.1.4.1.1954.3.1.2.1.4.1
Il numero di entry richieste, ovvero le tabelle X25CvTab relative ad ogni interfaccia
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25CvNEntryGar 1.3.6.1.4.1.1954.3.1.2.1.4.2
Il numero di entry massime garantite, ovvero il numero massimo di tabelle X25CvTab relative all'interfaccia
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvClrTable 1.3.6.1.4.1.1954.3.1.2.1.4.3
Tabella dello Stato dei C.V. ABBATTUTI sull'interfaccia
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    X25CvClrEntry

x25CvClrEntry 1.3.6.1.4.1.1954.3.1.2.1.4.3.1
Entry tabella X25CvClrTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  X25CvClrEntry  

x25CvClrIfcInd 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.1
Indice dell'interfaccia X.25
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvClrInd 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.2
Questo indice (65520 ...1) identifica in maniera univoca la entry relativa al C.V. abbattuto. L'indice parte da 65520 ed e' decrementato per ogni nuova entry addizionata alla tabella. Quando l'indice va a 0 si riparte da 65520 e tutte le entry sono ripulite per ripartire da capo. La getnext con indice 0 fornira' la entry piu' recente, dunque con indice piu' basso. Si ricorda che il numero massimo di entry memoriz- zate in tabella sono pari al valore assunto dalla variabile X25CvNEntryReq.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvTimeEst 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.3
Valore di sysUpTime relativo all'attivazione del C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

x25CvTimeClr 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.4
Valore di sysUpTime relativo all'abbattimento del C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

x25CvLcnLcgn 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.5
Numero del C.V. (0...4095) che e' stato abbattuto (LCGN+LCN).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvLastClrDir 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.6
Direzione (Tx/Rx) dell'ultimo pacchetto di CLR sul C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER clr-TX(1), clr-RX(2)  

x25CvClrCause 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.7
Causa relativa all'ultimo pacchetto di CLR sul C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvClrDiag 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.8
Diagnostica relativa all'ultimo pacchetto di CLR sul C.V.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25CvClrCalling 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.9
NUA chiamante del C.V. abbattuto.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

x25CvClrCalled 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.10
NUA chiamato del C.V. abbattuto.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

x25CvClrProtId 1.3.6.1.4.1.1954.3.1.2.1.4.3.1.11
Protocol Identifier del C.V. abbattuto.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

x25RoutTable 1.3.6.1.4.1.1954.3.1.2.2.1
Tabella instradamento X25/L4 Ogni riga di configurazione e' relativa all'instradamento X25 ADD CONNECTION (vedi manuale di configurazione del SW GAIA) e' una entry .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    X25RoutEntry

x25RoutEntry 1.3.6.1.4.1.1954.3.1.2.2.1.1
Entry tabella X25RoutTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  X25RoutEntry  

x25RoutInd 1.3.6.1.4.1.1954.3.1.2.2.1.1.1
Indice corrispondente al numero di entry in tabella
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25RoutIfcSource 1.3.6.1.4.1.1954.3.1.2.2.1.1.2
Interfaccia sorgente
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25RoutAddrSource 1.3.6.1.4.1.1954.3.1.2.2.1.1.3
Indirizzo sorgente (NUA o Sottoindirizzo)
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

x25RoutIfcDest 1.3.6.1.4.1.1954.3.1.2.2.1.1.4
Interfaccia destinataria
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25RoutLinkDest 1.3.6.1.4.1.1954.3.1.2.2.1.1.5
Link destinatario valido solo per interfacce destinatarie SDLC e 802
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25PvcTable 1.3.6.1.4.1.1954.3.1.2.2.2
Tabella connessione PVC relativa a X25/L4. Ad ogni entry corrisponde una riga del comando di configurazione: ADD CONNECTION PVC (vedi manuale di configurazione del SW GAIA).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    X25PvcEntry

x25PvcEntry 1.3.6.1.4.1.1954.3.1.2.2.2.1
Entry tabella X25PvcTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  X25PvcEntry  

x25PvcInd 1.3.6.1.4.1.1954.3.1.2.2.2.1.1
Indice corrispondente al numero di entry in tabella
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25PvcIfcSource 1.3.6.1.4.1.1954.3.1.2.2.2.1.2
Interfaccia sorgente
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25PvcPvcSource 1.3.6.1.4.1.1954.3.1.2.2.2.1.3
Numero PVC sorgente
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25PvcIfcDest 1.3.6.1.4.1.1954.3.1.2.2.2.1.4
Interfaccia destinataria
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x25PvcPvcDest 1.3.6.1.4.1.1954.3.1.2.2.2.1.5
Numero PVC destinatario
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

agendaTable 1.3.6.1.4.1.1954.3.1.2.3
tabella agenda
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgendaEntry

agendaEntry 1.3.6.1.4.1.1954.3.1.2.3.1
Entry tabella Agenda
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AgendaEntry  

x25AgIndex 1.3.6.1.4.1.1954.3.1.2.3.1.1
Indice della generica entry di agenda
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25AgNua 1.3.6.1.4.1.1954.3.1.2.3.1.2
nua memorizzato in agenda
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25AgCypher 1.3.6.1.4.1.1954.3.1.2.3.1.3
cifratura on/off
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25AgChain 1.3.6.1.4.1.1954.3.1.2.3.1.4
concatenazione on/off
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25AgIntegr 1.3.6.1.4.1.1954.3.1.2.3.1.5
integrazione on/off
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25AgSignt 1.3.6.1.4.1.1954.3.1.2.3.1.6
firma on/off
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25AgAuth 1.3.6.1.4.1.1954.3.1.2.3.1.7
autenticazione on/off
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25AgAccessctrl 1.3.6.1.4.1.1954.3.1.2.3.1.8
controllo di accesso on/off
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25AgAuthintv 1.3.6.1.4.1.1954.3.1.2.3.1.9
intervallo di autenticazione
Status: mandatory Access: read-write
OBJECT-TYPE    
  TimeTicks  

agState 1.3.6.1.4.1.1954.3.1.2.4
Questa variabile definisce i possibili stati della tabella Agenda. Valori possibili: 0: Agenda corrotta; 1: Agenda presente e avente almeno una entry; 2: Agenda presente e avente 0 entries; 3: Agenda non presente (il che significa che non e presente l'apparato di crittografia).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

cryCardInOut 1.3.6.1.4.1.1954.3.1.2.5
Questa variabile specifica se, in un apparato con CryptoCard, essa e inserita o meno. Valori possibili: 1: Crypto Card in 0: Crypto Card out Negli apparati con Crypto Device, essa vale sempre 1.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25Rmtkey 1.3.6.1.4.1.1954.3.1.2.6
chiave pubblica del dispositivo rmt
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

x25Ltc 1.3.6.1.4.1.1954.3.1.2.7
last trap confirmed yes/no
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25KeyGen 1.3.6.1.4.1.1954.3.1.3.1
Questa variabile gestisce il processo di generazione delle chiavi Valori possibili: 0: Non viene intrapresa nessuna azione; 1: Avvia la procedura di generazione delle chiavi; 2: Scrittura delle chiavi generate e loro cancellazione; 3: Cancellazione delle chiavi generate senza scrittura.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25IdReq 1.3.6.1.4.1.1954.3.1.3.2
Questa variabile gestisce: 1 - aggiornamento dell'agenda se settata a -1; 2 - servizio di autolearning, in questo caso viene settata dal CGS in seguito ad una trap inviata dal dispositivo e pu assumere un valore >= 0;
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

x25KeyReq-h 1.3.6.1.4.1.1954.3.1.3.3
Questa variabile contiene i primi 244 byte del record agenda inviato dal CGS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

x25KeyReq-l 1.3.6.1.4.1.1954.3.1.3.4
Questa variabile contiene gli ultimi 243 byte del record agenda inviato dal CGS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

lapbDiag 1.3.6.1.4.1.1954.3.2.2
OBJECT IDENTIFIER    

lapbDiagIfc 1.3.6.1.4.1.1954.3.2.2.1
OBJECT IDENTIFIER    

lapbCnfTable 1.3.6.1.4.1.1954.3.2.2.1.1
Tabella dei parametri di configurazione Lapb relativi ad una interfaccia.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LapbCnfEntry

lapbCnfEntry 1.3.6.1.4.1.1954.3.2.2.1.1.1
Entry tabella LapbCnfTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LapbCnfEntry  

lapbCnfIfc 1.3.6.1.4.1.1954.3.2.2.1.1.1.1
L'interfaccia su cui e` configurata l'entita` LAPB, corrisponde a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapbType 1.3.6.1.4.1.1954.3.2.2.1.1.1.2
La modalita` DTE/DCE LAPB
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dte(1), dce(2)  

lapbModule 1.3.6.1.4.1.1954.3.2.2.1.1.1.3
Il modulo (8 / 128)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapbN1 1.3.6.1.4.1.1954.3.2.2.1.1.1.4
Il valore di N1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapbK 1.3.6.1.4.1.1954.3.2.2.1.1.1.5
Il valore di k
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapbN2 1.3.6.1.4.1.1954.3.2.2.1.1.1.6
Il valore di N2
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapbT1 1.3.6.1.4.1.1954.3.2.2.1.1.1.7
Il valore di T1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adslmib 1.3.6.1.4.1.1954.3.12.1
OBJECT IDENTIFIER    

adsllinemib 1.3.6.1.4.1.1954.3.12.1.1
OBJECT IDENTIFIER    

adslMibObject 1.3.6.1.4.1.1954.3.12.1.1.1
OBJECT IDENTIFIER    

adslLineCodingType 1.3.6.1.4.1.1954.3.12.1.1.1.1
Defines the type of ADSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noChannel(1), fastOnly(2), interleavedOnly(3), fastOrInterleaved(4), fastAndInterleaved(5)  

adslAturPhysTable 1.3.6.1.4.1.1954.3.12.1.1.1.2
This table provides one row for each ATUR Each row contains the Physical Layer Parameters table for that ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAturPhysEntry

adslAturPhysEntry 1.3.6.1.4.1.1954.3.12.1.1.1.2.1
An entry in the adslAturPhysTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslAturPhysEntry  

adslAturifIndex 1.3.6.1.4.1.1954.3.12.1.1.1.2.1.1
IFindex
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -640..640  

adslAturIndex 1.3.6.1.4.1.1954.3.12.1.1.1.2.1.2
index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -640..640  

adslAturInvSerialNumber 1.3.6.1.4.1.1954.3.12.1.1.1.2.1.3
The vendor specific string that identifies the vendor equipment.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslAturInvVendorID 1.3.6.1.4.1.1954.3.12.1.1.1.2.1.4
The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslAturInvVersionNumber 1.3.6.1.4.1.1954.3.12.1.1.1.2.1.5
The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslAturCurrSnrMgn 1.3.6.1.4.1.1954.3.12.1.1.1.2.1.6
Noise Margin as seen by this ATU with respect to its received signal in tenth dB.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -640..640  

adslAturCurrAtn 1.3.6.1.4.1.1954.3.12.1.1.1.2.1.7
Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

adslAturCurrStatus 1.3.6.1.4.1.1954.3.12.1.1.1.2.1.8
Indicates current state of the ATUR line. This is a bit-map of possible conditions. Due to the isolation of the ATUR when line problems occur, many state conditions like loss of power, loss of quality signal, and initialization errors, can not be determined. While trouble shooting ATUR, also use object, adslAtucCurrStatus. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUR failure due to not receiving valid frame 2 lossOfSignal ATUR failure due to not receiving signal 3 lossOfPower ATUR failure due to loss of power 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. This is intended to supplement ifOperStatus.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4)  

adslAturCurrOutputPwr 1.3.6.1.4.1.1954.3.12.1.1.1.2.1.9
Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -310..310  

adslAturCurrAttainableRate 1.3.6.1.4.1.1954.3.12.1.1.1.2.1.10
Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge  

adslAtucPhysTable 1.3.6.1.4.1.1954.3.12.1.1.1.3
This table provides one row for each ATUC Each row contains the Physical Layer Parameters table for that ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAtucPhysEntry

adslAtucPhysEntry 1.3.6.1.4.1.1954.3.12.1.1.1.3.1
An entry in the adslAturPhysTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslAtucPhysEntry  

adslAtucifIndex 1.3.6.1.4.1.1954.3.12.1.1.1.3.1.1
IFindex
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -640..640  

adslAtucIndex 1.3.6.1.4.1.1954.3.12.1.1.1.3.1.2
index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -640..640  

adslAtucInvVendorID 1.3.6.1.4.1.1954.3.12.1.1.1.3.1.3
The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslAtucInvVersionNumber 1.3.6.1.4.1.1954.3.12.1.1.1.3.1.4
The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslAtucCurrStatus 1.3.6.1.4.1.1954.3.12.1.1.1.3.1.5
Indicates current state of the ATUR line. This is a bit-map of possible conditions. Due to the isolation of the ATUR when line problems occur, many state conditions like loss of power, loss of quality signal, and initialization errors, can not be determined. While trouble shooting ATUR, also use object, adslAtucCurrStatus. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUR failure due to not receiving valid frame 2 lossOfSignal ATUR failure due to not receiving signal 3 lossOfPower ATUR failure due to loss of power 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. This is intended to supplement ifOperStatus.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4)  

adslAtucCurrOutputPwr 1.3.6.1.4.1.1954.3.12.1.1.1.3.1.6
Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -310..310  

adslAtucCurrAttainableRate 1.3.6.1.4.1.1954.3.12.1.1.1.3.1.7
Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge  

adslAturChanTable 1.3.6.1.4.1.1954.3.12.1.1.1.4
This table provides one row for each ATUC channel
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAturChanEntry

adslAturChanEntry 1.3.6.1.4.1.1954.3.12.1.1.1.4.1
An entry in the adslAtucChanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslAturChanEntry  

adslAturChanIfIndex 1.3.6.1.4.1.1954.3.12.1.1.1.4.1.1
index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -640..640  

adslAturChanIndex 1.3.6.1.4.1.1954.3.12.1.1.1.4.1.2
index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER -640..640  

adslAturChanCurrTxRate 1.3.6.1.4.1.1954.3.12.1.1.1.4.1.3
Actual transmit rate on this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

adslAturChanCorrectedBlks 1.3.6.1.4.1.1954.3.12.1.1.1.4.1.4
Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslAturChanUncorrectBlks 1.3.6.1.4.1.1954.3.12.1.1.1.4.1.5
Count of all blocks received with uncorrectable errors since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslAturChanReceivedCells 1.3.6.1.4.1.1954.3.12.1.1.1.4.1.6
Count of all cells received
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslAturChanTransmittedCells 1.3.6.1.4.1.1954.3.12.1.1.1.4.1.7
Count of all cells transmitted
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslAtucChanTable 1.3.6.1.4.1.1954.3.12.1.1.1.5
This table provides one row for each ATUC channel
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAtucChanEntry

adslAtucChanEntry 1.3.6.1.4.1.1954.3.12.1.1.1.5.1
An entry in the adslAtucChanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslAtucChanEntry  

adslAtucChanIfIndex 1.3.6.1.4.1.1954.3.12.1.1.1.5.1.1
index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

adslAtucChanIndex 1.3.6.1.4.1.1954.3.12.1.1.1.5.1.2
index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

adslAtucChanCurrTxRate 1.3.6.1.4.1.1954.3.12.1.1.1.5.1.3
Actual transmit rate on this channel.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

adslAtucChanCorrectedBlks 1.3.6.1.4.1.1954.3.12.1.1.1.5.1.4
Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslAtucChanUncorrectBlks 1.3.6.1.4.1.1954.3.12.1.1.1.5.1.5
Count of all blocks received with uncorrectable errors since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

atmmib 1.3.6.1.4.1.1954.3.13.1
OBJECT IDENTIFIER    

atmMibObject 1.3.6.1.4.1.1954.3.13.1.1
OBJECT IDENTIFIER    

atmPvcTable 1.3.6.1.4.1.1954.3.13.1.1.1
This table provides one row for each PVC
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    AtmPvcEntry

atmPvcEntry 1.3.6.1.4.1.1954.3.13.1.1.1.1
An entry in the atmPvcTable .
Status: mandatory Access: read-only
OBJECT-TYPE    
  AtmPvcEntry  

atmifIndex 1.3.6.1.4.1.1954.3.13.1.1.1.1.1
index
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atmpvcIndex 1.3.6.1.4.1.1954.3.13.1.1.1.1.2
index
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

atmPvc 1.3.6.1.4.1.1954.3.13.1.1.1.1.3
The PVC value of the VCC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

atmVpi 1.3.6.1.4.1.1954.3.13.1.1.1.1.4
The VPI value of the VCC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

atmVci 1.3.6.1.4.1.1954.3.13.1.1.1.1.5
The VCI value of the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

atmVccAalType 1.3.6.1.4.1.1954.3.13.1.1.1.1.6
The type of AAL used on this VCC. The AAL type includes AAL1, AAL2, AAL3/4, and AAL5. The other(4) may be user-defined AAL type. The unknown type indicates that the AAL type cannot be determined.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

atmVccMode 1.3.6.1.4.1.1954.3.13.1.1.1.1.7
The type of pacing mode
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

atmAalEncapsType 1.3.6.1.4.1.1954.3.13.1.1.1.1.8
An instance of this object only exists when the local VCL end-point is also the VCC end-point, and AAL5 is in use. The type of data encapsulation used over the AAL5 SSCS layer. The definitions reference RFC 1483 Multiprotocol Encapsulation over ATM AAL5 and to the ATM Forum LAN Emulation specification.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

atmPvcSpeed 1.3.6.1.4.1.1954.3.13.1.1.1.1.9
Pvc bit rate as percentage of the maximum available bandwidth (100 %)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcInOctets 1.3.6.1.4.1.1954.3.13.1.1.1.1.10
The number of octets received on the pvc, including framing characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcUcastPkts 1.3.6.1.4.1.1954.3.13.1.1.1.1.11
The number of subnetwork-unicast packets delivered to a higher-layer protocol on pvc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcNUcastPkts 1.3.6.1.4.1.1954.3.13.1.1.1.1.12
The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol over pvc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcDiscards 1.3.6.1.4.1.1954.3.13.1.1.1.1.13
The number of inbound packets for pvc which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcErrors 1.3.6.1.4.1.1954.3.13.1.1.1.1.14
The number of inbound packets for pvc that contained errors preventing them from being deliverable to a higher-layer protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcUnknownProtos 1.3.6.1.4.1.1954.3.13.1.1.1.1.15
The number of packets for pvc received via the interface which were discarded because of an unknown or unsupported protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcOutOctets 1.3.6.1.4.1.1954.3.13.1.1.1.1.16
The number of octets for pvc transmitted out of the interface, including framing characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcOutUcastPkts 1.3.6.1.4.1.1954.3.13.1.1.1.1.17
The number of packets for pvc that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcOutNUcastPkts 1.3.6.1.4.1.1954.3.13.1.1.1.1.18
The number of packets for pvc that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcOutDiscards 1.3.6.1.4.1.1954.3.13.1.1.1.1.19
The number of outbound packets for pvc which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

atmPvcOutErrors 1.3.6.1.4.1.1954.3.13.1.1.1.1.20
The number of outbound packets for pvc that could not be transmitted because of errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbOpTable 1.3.6.1.4.1.1954.3.2.2.1.2
Questa tabella fornisce i parametri operativi di una interfaccia Lapb.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LapbOpEntry

lapbOpEntry 1.3.6.1.4.1.1954.3.2.2.1.2.1
Entry tabella LapbOpTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LapbOpEntry  

lapbOpIfc 1.3.6.1.4.1.1954.3.2.2.1.2.1.1
Indice dell'interfaccia su cui e` operativa l'entita` LAPB,corrisponde a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapbOpState 1.3.6.1.4.1.1954.3.2.2.1.2.1.2
Lo stato del Lapb
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disconnected(0), await-Est(1), await-Rel(2), established(3), frmr-Condition(5), rej-sent(6), busy-on-TX(7), busy-on-RX(8), busy-on-TXRX(9)  

lapbNRejTx 1.3.6.1.4.1.1954.3.2.2.1.2.1.3
Contatore REJ trasmessi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNRejRx 1.3.6.1.4.1.1954.3.2.2.1.2.1.4
Contatore REJ ricevuti
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNRitr 1.3.6.1.4.1.1954.3.2.2.1.2.1.5
Contatore ritrasmissioni
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNFrmrTx 1.3.6.1.4.1.1954.3.2.2.1.2.1.6
Contatore FRMR trasmessi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNFrmrRx 1.3.6.1.4.1.1954.3.2.2.1.2.1.7
Contatore FRMR ricevuti
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNIframeTx 1.3.6.1.4.1.1954.3.2.2.1.2.1.8
Contatore I-Frame trasmesse
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNIframeRx 1.3.6.1.4.1.1954.3.2.2.1.2.1.9
Contatore I-Frame ricevute
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNRRTx 1.3.6.1.4.1.1954.3.2.2.1.2.1.10
Contatore RR trasmessi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNRRRx 1.3.6.1.4.1.1954.3.2.2.1.2.1.11
Contatore RR ricevuti
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNRNRTx 1.3.6.1.4.1.1954.3.2.2.1.2.1.12
Contatore RNR trasmessi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNRNRRx 1.3.6.1.4.1.1954.3.2.2.1.2.1.13
Contatore RNR ricevuti
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapbNNsErr 1.3.6.1.4.1.1954.3.2.2.1.2.1.14
Contatore N(s) Errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdDiag 1.3.6.1.4.1.1954.3.3.2
OBJECT IDENTIFIER    

lapdDiagIfc 1.3.6.1.4.1.1954.3.3.2.1
OBJECT IDENTIFIER    

lapdCnfTable 1.3.6.1.4.1.1954.3.3.2.1.1
Questa tabella descrive i parametri relativi alla configurazione Lapd per ogni link Lapd. Se si lavora in TEI automatico la entry viene aggiunta in tabella al momento dell'attivazione del link e rimane anche se il liv.2 viene abbattuto. Questo significa che se interrogo la tabella all'attiva- zione della macchina (inizializzazione lapd) non trovo nessuna entry relativa ai link lapd di lavoro (TEI tra 63...127), se e' stato attivato il colloquio Lapd trovero' la entry con un una numerazione del link dove il TEI e' quello assegnato dalla rete. Se si lavora con TEI fisso la entry viene aggiunta alla tabella all'inizializzazione del protocollo Lapd ed e' sempre presente.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LapdCnfEntry

lapdCnfEntry 1.3.6.1.4.1.1954.3.3.2.1.1.1
Entry tabella LapdCnfTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LapdCnfEntry  

lapdCnfIfc 1.3.6.1.4.1.1954.3.3.2.1.1.1.1
Indice dell'interfaccia su cui e` configurata l'entita` Lapd, corrisponde a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapdCnfTeiSapi 1.3.6.1.4.1.1954.3.3.2.1.1.1.2
Questa variabile (2^ indice) identifica l'indirizzo del link LAPD, dato dall'accoppiata TEI+SAPI. E' l'espressione decimale del TEI * 100 a cui viene addizionato il SAPI (TEI*100+SAPI). Es: indice=12763 corrisponde a TEI=127 SAPI=63. Si ricorda a tal proposito che i valori che puo' assumere il TEI vanno da 0...127 e il SAPI da 0..63.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapdCnfN200 1.3.6.1.4.1.1954.3.3.2.1.1.1.3
Valore parametro N200
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapdCnfN201 1.3.6.1.4.1.1954.3.3.2.1.1.1.4
Massima lunghezza campo Info
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapdCnfT200 1.3.6.1.4.1.1954.3.3.2.1.1.1.5
Tempo replica
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapdCnfT203 1.3.6.1.4.1.1954.3.3.2.1.1.1.6
Tempo max senza trasmissione trame
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapdCnfK 1.3.6.1.4.1.1954.3.3.2.1.1.1.7
Numero massimo di trame in attesa risposta (finestra)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapdOpTable 1.3.6.1.4.1.1954.3.3.2.1.2
Questa tabella descrive i parametri operativi per ogni link LAPD. Per l'inserimento di una entry vale quanto detto per la tabella LapdCnfTab.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LapdOpEntry

lapdOpEntry 1.3.6.1.4.1.1954.3.3.2.1.2.1
Entry tabella LapdOpTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LapdOpEntry  

lapdOpIfc 1.3.6.1.4.1.1954.3.3.2.1.2.1.1
Indice dell'interfaccia su cui e` configurata l'entita` X25. Si noti che questo valore coincide con quello riportato dalla ifIndex
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapdOpTeiSapi 1.3.6.1.4.1.1954.3.3.2.1.2.1.2
Questa variabile (2^ indice) identifica l'indirizzo del link LAPD, dato dall'accoppiata TEI+SAPI. E' l'espressione deciamle del TEI * 100 a cui viene addizionato il SAPI (TEI*100+SAPI). Es: indice=12763 corrisponde a TEI=127 SAPI=63. Si ricorda a tal proposito che i valori che puo' assumere il TEI vanno da 0...127 e il SAPI da 0..63.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lapdOpState 1.3.6.1.4.1.1954.3.3.2.1.2.1.3
Sato relativo al link specificato con gli indici - Nota: un link con TEI 127 e' sempre nello stato broadcast
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER tei-unassigned(0), assign-awaiting-TEI(1), establish-awaiting-TEI(2), tei-assigned(3), awaiting-establish(4), awaiting-release(5), multiple-frame-established(6), timer-recovery(7), broadcast-information-transfer(8), state-Rej-sottostato-di-6-7(9), state-Tx-Inibit-sottostato-di-6-7(10), state-Rx-inibit-sottostato-di-6-7(11)  

lapdOpNRejTx 1.3.6.1.4.1.1954.3.3.2.1.2.1.4
Contatore REJ trasmessi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNRejRx 1.3.6.1.4.1.1954.3.3.2.1.2.1.5
Contatore REJ ricevuti
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNRitr 1.3.6.1.4.1.1954.3.3.2.1.2.1.6
Contatore ritrasmissioni
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNFrmrTx 1.3.6.1.4.1.1954.3.3.2.1.2.1.7
Contatore FRMR trasmessi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNFrmrRx 1.3.6.1.4.1.1954.3.3.2.1.2.1.8
Contatore FRMR ricevuti
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNIframeTx 1.3.6.1.4.1.1954.3.3.2.1.2.1.9
Contatore I-FRAME trasmesse
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNIframeRx 1.3.6.1.4.1.1954.3.3.2.1.2.1.10
Contatore I-FRAME ricevute
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNRrTx 1.3.6.1.4.1.1954.3.3.2.1.2.1.11
Contatore RR trasmessi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNRrRx 1.3.6.1.4.1.1954.3.3.2.1.2.1.12
Contatore RR ricevuti
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNRnrTx 1.3.6.1.4.1.1954.3.3.2.1.2.1.13
Contatore RNR trasmessi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNRnrRx 1.3.6.1.4.1.1954.3.3.2.1.2.1.14
Contatore RNR ricevuti
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNsErr 1.3.6.1.4.1.1954.3.3.2.1.2.1.15
Contatore N(s) Errati
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNUiTx 1.3.6.1.4.1.1954.3.3.2.1.2.1.16
Contatore UI trasmesse
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

lapdOpNUiRx 1.3.6.1.4.1.1954.3.3.2.1.2.1.17
Contatore UI ricevute
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

q931Diag 1.3.6.1.4.1.1954.3.4.2
OBJECT IDENTIFIER    

q931OpTable 1.3.6.1.4.1.1954.3.4.2.2
Tabella operativa Q931
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Q931OpEntry

q931OpEntry 1.3.6.1.4.1.1954.3.4.2.2.1
Entry tabella Q931OpTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Q931OpEntry  

q931OpIfc 1.3.6.1.4.1.1954.3.4.2.2.1.1
Indice dell'interfaccia relativa al canale B ISDN controllato dal Q931, ha corrispondenza con ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

q931OpState 1.3.6.1.4.1.1954.3.4.2.2.1.2
Stato della Chiamata Q931
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER null(0), call-Initiated(1), overlap-Sending(2), outgoing-Call-Proceeding(3), call-Delivered(4), call-Present(5), call-Received(6), connect-Request(7), incoming-Call-Proceeding(8), active(9), disconnect-Request(10), disconnect-Indication(11), suspend-Request(12), resume-Request(13), release-Request(14), overlap-Receiving(15)  

q931LastCalled 1.3.6.1.4.1.1954.3.4.2.2.1.3
Ultimo numero di telefono Isdn chiamato
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

q931LastCalling 1.3.6.1.4.1.1954.3.4.2.2.1.4
Ultimo numero di telefono Isdn chiamante
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

q931LastCauseDisc 1.3.6.1.4.1.1954.3.4.2.2.1.5
Ultima causa di Disconnessione dalla Rete
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipDiag 1.3.6.1.4.1.1954.3.5.2
OBJECT IDENTIFIER    

ipSec 1.3.6.1.4.1.1954.3.5.3
OBJECT IDENTIFIER    

ipDiagIfc 1.3.6.1.4.1.1954.3.5.2.1
OBJECT IDENTIFIER    

ipGlob 1.3.6.1.4.1.1954.3.5.2.2
OBJECT IDENTIFIER    

ipDiagAccessList 1.3.6.1.4.1.1954.3.5.2.4
OBJECT IDENTIFIER    

ipIfcCnfTable 1.3.6.1.4.1.1954.3.5.2.1.1
Questa tabella riassume i parametri di configurazione relativi ad una interfaccia di tipo IP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpIfcCnfEntry

ipIfcCnfEntry 1.3.6.1.4.1.1954.3.5.2.1.1.1
Entry configurazione ifc IP
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpIfcCnfEntry  

ipIfcCnfInd 1.3.6.1.4.1.1954.3.5.2.1.1.1.1
Indice interfaccia IP corrispondente a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipIfcAddress 1.3.6.1.4.1.1954.3.5.2.1.1.1.2
Indirizzo IP dell'interfaccia.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipMask 1.3.6.1.4.1.1954.3.5.2.1.1.1.3
Subnet mask
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipIdleTmo 1.3.6.1.4.1.1954.3.5.2.1.1.1.4
Valore relativo a Idle timeout (tempo di inattivita' relativo alla connessione IP) Valori ammessi da 0...65535, in relazione al comando di configurazione.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ipMtu 1.3.6.1.4.1.1954.3.5.2.1.1.1.5
MTU relativa al livello IP sull'interfaccia (dimensione massima del pacchetto dati).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

ipRedirect 1.3.6.1.4.1.1954.3.5.2.1.1.1.6
Abilitazione all'invio di una trama di Redirect
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1)  

ipDefGtw 1.3.6.1.4.1.1954.3.5.2.2.1
Default gateway (0.0.0.0 se non configurato).
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipDGtwIfc 1.3.6.1.4.1.1954.3.5.2.2.2
Indice interfaccia (ifIndex) su cui il Default gateway e' attivo.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipSROpt 1.3.6.1.4.1.1954.3.5.2.2.3
Abilitazione dell'opzione Source Route.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(0), on(1)  

ipRouteTable 1.3.6.1.4.1.1954.3.5.2.3
Questa tabella fornisce informazioni sulla geografica (intesa come instradamento verso un gateway), aperta attraverso una interfaccia e sul traffico svolto da essa. La tabella e' indicizzata per interfaccia e per gateway ed e' interrogabile solo su interfacce di tipo switched come X25 e Frame Relay. Una entry viene inserita in tabella quando la ROUTE viene aperta: all'inizializzazione delle interfacce per i PVC, alla formazione della chiamata per gli SVC. Per gli SVC la entry viene tolta dalla tabella al momento dell'abbattimento della chiamata.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpRouteEntry

ipRouteEntry 1.3.6.1.4.1.1954.3.5.2.3.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpRouteEntry  

ipRouteTabIfc 1.3.6.1.4.1.1954.3.5.2.3.1.1
Indice relativo all'interfaccia, corrisponde a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipRouteTabGtw 1.3.6.1.4.1.1954.3.5.2.3.1.2
Gateway raggiunto (remoto).
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipRouteTabPkTx 1.3.6.1.4.1.1954.3.5.2.3.1.3
Contatore di pacchetti trasmessi.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipRouteTabPkRx 1.3.6.1.4.1.1954.3.5.2.3.1.4
Contatore pacchetti ricevuti.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipRouteTabPSW 1.3.6.1.4.1.1954.3.5.2.3.1.5
Tipo circuito: permanent o switched. Nel caso di PVC indica il numero di circuito, per gli SVC viene indicato il valore 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switched(0)  

ipRouteTabTime 1.3.6.1.4.1.1954.3.5.2.3.1.6
Tempo di sistema relativo all'apertura della .
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

ipDiagAlInternalEnable 1.3.6.1.4.1.1954.3.5.2.4.1
Internal access List abilitation flag.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipDiagAlRoutingEnable 1.3.6.1.4.1.1954.3.5.2.4.2
Routing access List abilitation flag.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipDiagAlNumInternalEntry 1.3.6.1.4.1.1954.3.5.2.4.3
Internal access List's number of entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipDiagAlNumRoutingEntry 1.3.6.1.4.1.1954.3.5.2.4.4
Routing access List's number of entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipDiagAlInternTable 1.3.6.1.4.1.1954.3.5.2.4.5
Access List Intern table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    IpDiagAlInternEntry

ipDiagAlInternEntry 1.3.6.1.4.1.1954.3.5.2.4.5.1
Entry of the Access List Intern table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpDiagAlInternEntry  

ipDiagAlInternIndex 1.3.6.1.4.1.1954.3.5.2.4.5.1.1
Index of the Access List Intern table entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipDiagAlInternPermDenFlag 1.3.6.1.4.1.1954.3.5.2.4.5.1.2
Entry flag permitted-denied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER permitted(0), denied(1)  

ipDiagAlInternIpSrc 1.3.6.1.4.1.1954.3.5.2.4.5.1.3
Sender IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipDiagAlInternMaskSrc 1.3.6.1.4.1.1954.3.5.2.4.5.1.4
Sender IP mask.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipDiagAlInternIpDest 1.3.6.1.4.1.1954.3.5.2.4.5.1.5
Receiver IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipDiagAlInternMaskDst 1.3.6.1.4.1.1954.3.5.2.4.5.1.6
Receiver IP mask.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipDiagAlInternIfc 1.3.6.1.4.1.1954.3.5.2.4.5.1.7
Interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(-1), ethernet1(0), serial1(1), isdn1-B1(2), isdn1-D(3), serial2(4), serial3(5), serial4(6), ethernet2(7), ethernet3(8), ethernet4(9), cpci(10), ethernet5(11), isdn1-B2(12), isdn1-B(13), ethernet6(14)  

ipDiagAlInternTcpProt 1.3.6.1.4.1.1954.3.5.2.4.5.1.8
Check on Tcp protocol enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0), checked(1)  

ipDiagAlInternTcpPort 1.3.6.1.4.1.1954.3.5.2.4.5.1.9
Tcp port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0)  

ipDiagAlInternPConnSt 1.3.6.1.4.1.1954.3.5.2.4.5.1.10
Check on connection state enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipDiagAlInternUdpProt 1.3.6.1.4.1.1954.3.5.2.4.5.1.11
Check on Udp protocol enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0), checked(1)  

ipDiagAlInternUdpPort 1.3.6.1.4.1.1954.3.5.2.4.5.1.12
Udp port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0)  

ipDiagAlInternIcmpProt 1.3.6.1.4.1.1954.3.5.2.4.5.1.13
Check on Icmp protocol enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0), checked(1)  

ipDiagAlInternAhProt 1.3.6.1.4.1.1954.3.5.2.4.5.1.14
Check on Ah protocol enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0), checked(1)  

ipDiagAlInternEspProt 1.3.6.1.4.1.1954.3.5.2.4.5.1.15
Check on Esp protocol enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0), checked(1)  

ipDiagAlRouteTable 1.3.6.1.4.1.1954.3.5.2.4.6
Access List Route table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    IpDiagAlRouteEntry

ipDiagAlRouteEntry 1.3.6.1.4.1.1954.3.5.2.4.6.1
Entry of the Access List Route table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpDiagAlRouteEntry  

ipDiagAlRouteIndex 1.3.6.1.4.1.1954.3.5.2.4.6.1.1
Index of the Access List Route table entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipDiagAlRoutePermDenFlag 1.3.6.1.4.1.1954.3.5.2.4.6.1.2
Entry flag permitted-denied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER permitted(0), denied(1)  

ipDiagAlRouteIpSrc 1.3.6.1.4.1.1954.3.5.2.4.6.1.3
Sender IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipDiagAlRouteMaskSrc 1.3.6.1.4.1.1954.3.5.2.4.6.1.4
Sender IP mask.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipDiagAlRouteIpDest 1.3.6.1.4.1.1954.3.5.2.4.6.1.5
Receiver IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipDiagAlRouteMaskDst 1.3.6.1.4.1.1954.3.5.2.4.6.1.6
Receiver IP mask.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipDiagAlRouteIfc 1.3.6.1.4.1.1954.3.5.2.4.6.1.7
Interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(-1), ethernet1(0), serial1(1), isdn1-B1(2), isdn1-D(3), serial2(4), serial3(5), serial4(6), ethernet2(7), ethernet3(8), ethernet4(9), cpci(10), ethernet5(11), isdn1-B2(12), isdn1-B(13), ethernet6(14)  

ipDiagAlRouteTcpProt 1.3.6.1.4.1.1954.3.5.2.4.6.1.8
Check on Tcp protocol checked- not checked.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0), checked(1)  

ipDiagAlRouteTcpPort 1.3.6.1.4.1.1954.3.5.2.4.6.1.9
Tcp port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0)  

ipDiagAlRoutePConnSt 1.3.6.1.4.1.1954.3.5.2.4.6.1.10
Check on connection state enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipDiagAlRouteUdpProt 1.3.6.1.4.1.1954.3.5.2.4.6.1.11
Check on Udp protocol enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0), checked(1)  

ipDiagAlRouteUdpPort 1.3.6.1.4.1.1954.3.5.2.4.6.1.12
Udp port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0)  

ipDiagAlRouteIcmpProt 1.3.6.1.4.1.1954.3.5.2.4.6.1.13
Check on Icmp protocol enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0), checked(1)  

ipDiagAlRouteAhProt 1.3.6.1.4.1.1954.3.5.2.4.6.1.14
Check on Ah protocol enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0), checked(1)  

ipDiagAlRouteEspProt 1.3.6.1.4.1.1954.3.5.2.4.6.1.15
Check on Esp protocol enabled-disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notChecked(0), checked(1)  

ipSecTrap 1.3.6.1.4.1.1954.3.5.3.6
OBJECT IDENTIFIER    

ipSecCardInOut 1.3.6.1.4.1.1954.3.5.3.1
SystemInfo AgPresent field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipSecTcTable 1.3.6.1.4.1.1954.3.5.3.2
This table provides informations about chypering gateways and configured security services.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    IpSecTcEntry

ipSecTcEntry 1.3.6.1.4.1.1954.3.5.3.2.1
Cryptography table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpSecTcEntry  

ipSecTcGtw 1.3.6.1.4.1.1954.3.5.3.2.1.1
Addressee chypering gateway.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipSecTcCypher 1.3.6.1.4.1.1954.3.5.3.2.1.2
Cyphering service ON/OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcIntegr 1.3.6.1.4.1.1954.3.5.3.2.1.4
Integrity service ON/OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcChain 1.3.6.1.4.1.1954.3.5.3.2.1.3
Chaining service ON/OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcSignt 1.3.6.1.4.1.1954.3.5.3.2.1.5
Electronic sign (authentication of the sender) ON/OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcAuth 1.3.6.1.4.1.1954.3.5.3.2.1.6
Authentication service ON/OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcAccessctrl 1.3.6.1.4.1.1954.3.5.3.2.1.7
Check on accesses service ON/OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcAuthStatus 1.3.6.1.4.1.1954.3.5.3.2.1.8
Gateway authentication status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipSecTcAuthTaut 1.3.6.1.4.1.1954.3.5.3.2.1.9
Average time beetwen authentication requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipSecTcAuthTmax 1.3.6.1.4.1.1954.3.5.3.2.1.10
Maximum waiting time for authentication replies.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipSecTcAuthNmax 1.3.6.1.4.1.1954.3.5.3.2.1.11
Maximum number of authentication requests before fail.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipSecTcFlashTable 1.3.6.1.4.1.1954.3.5.3.3
This table provides informations about chypering gateways and configured security services reading data directly in the flash memory (often referred as agenda).
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    IpSecTcFlashEntry

ipSecTcFlashEntry 1.3.6.1.4.1.1954.3.5.3.3.1
Cryptography table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpSecTcFlashEntry  

ipSecTcFlashGtw 1.3.6.1.4.1.1954.3.5.3.3.1.1
Addressee chypering gateway.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipSecTcFlashCypher 1.3.6.1.4.1.1954.3.5.3.3.1.2
Cyphering service ON/OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcFlashIntegr 1.3.6.1.4.1.1954.3.5.3.3.1.4
Integrity service ON/OFF
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcFlashChain 1.3.6.1.4.1.1954.3.5.3.3.1.3
Chaining service ON/OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcFlashSignt 1.3.6.1.4.1.1954.3.5.3.3.1.5
Electronic sign (authentication of the sender) ON/OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcFlashAuth 1.3.6.1.4.1.1954.3.5.3.3.1.6
Authentication service ON/OFF
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcFlashAccessctrl 1.3.6.1.4.1.1954.3.5.3.3.1.7
Check on accesses service ON/OFF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(0)  

ipSecTcFlashNotaio 1.3.6.1.4.1.1954.3.5.3.3.1.8
Certifying Notary IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipSecTcFlashValiditySince 1.3.6.1.4.1.1954.3.5.3.3.1.9
Validity begin date.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ipSecTcFlashValidityUntil 1.3.6.1.4.1.1954.3.5.3.3.1.10
Validity end date.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ipSecTcFlashInfo 1.3.6.1.4.1.1954.3.5.3.3.1.11
Entry's info field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ipSecNumEntry 1.3.6.1.4.1.1954.3.5.3.4
Number of entries in agenda.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipSecTcIpTable 1.3.6.1.4.1.1954.3.5.3.5
This table provides informations about which gateways have cryptography services configured for frames destined to them.
Status: mandatory Access: read-only
OBJECT-TYPE    
  SEQUENCE OF  
    IpSecTcIpEntry

ipSecTcIpEntry 1.3.6.1.4.1.1954.3.5.3.5.1
Cryptography table entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpSecTcIpEntry  

ipSecTcIpIpDst 1.3.6.1.4.1.1954.3.5.3.5.1.1
Addressee IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipSecTcIpMaskDst 1.3.6.1.4.1.1954.3.5.3.5.1.2
Addressee IP mask.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipSecTcIpGtwDst 1.3.6.1.4.1.1954.3.5.3.5.1.3
Cyphering gateway.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipSecTrapIndIp 1.3.6.1.4.1.1954.3.5.3.6.1
IP address of the gateway that caused the alarm to be sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

ipSecTrapKeyp 1.3.6.1.4.1.1954.3.5.3.6.2
Public key which caused the alarm to be sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ipSecTrapCode 1.3.6.1.4.1.1954.3.5.3.6.3
Specific trap sent: 38144-bad agend; 36864-authentication failed; 36868-gateway not responding.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipSecTrapDataValid 1.3.6.1.4.1.1954.3.5.3.6.4
States weather data are accessible or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER keyNotValid(2), valid(1), notValid(0)  

i802Diag 1.3.6.1.4.1.1954.3.6.2
OBJECT IDENTIFIER    

i802IfcCnfTable 1.3.6.1.4.1.1954.3.6.2.1
Questa tabella raccoglie le informazioni di configurazione 802.2 relative ad un'interfaccia.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    I802IfcCnfEntry

i802IfcCnfEntry 1.3.6.1.4.1.1954.3.6.2.1.1
Entry configurazione 802.2 ifc
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  I802IfcCnfEntry  

i802IfcCnfInd 1.3.6.1.4.1.1954.3.6.2.1.1.1
Indice relativo all'interfaccia 802.2, corrisponde a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  


i802IfcCrin 1.3.6.1.4.1.1954.3.6.2.1.1.3
Definisce la modalita' di instradamento (vedi manuale configurazione GAIA).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER criterio-NUALEN(1), criterio-SUBLEN(2), criterio-NONE(3)  

i802IfcLenCrin 1.3.6.1.4.1.1954.3.6.2.1.1.4
Lunghezza utilizzata dal criterio di instradamento: Valori ammessi: 0 se i802IfcCrin = NONE, da 1...15 se i802IfcCrin = NUALEN e SUBLEN
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802LinkCnfTable 1.3.6.1.4.1.1954.3.6.2.2
Questa tabella riporta tutte le informazioni di configurazione relative al singolo LINK 802.2 dell'interfaccia specificata.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    I802LinkCnfEntry

i802LinkCnfEntry 1.3.6.1.4.1.1954.3.6.2.2.1
Entry configurazione 802.2 link
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  I802LinkCnfEntry  

i802LinkIfc 1.3.6.1.4.1.1954.3.6.2.2.1.1
Indice dell'interfaccia, corrisponde a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802LinkInd 1.3.6.1.4.1.1954.3.6.2.2.1.2
Indice del link 802.2 con numerazione a partire da 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802LinkT200 1.3.6.1.4.1.1954.3.6.2.2.1.3
Valore del timer T200. Valori ammessi 5...200 espressi in ms.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802LinkTmng 1.3.6.1.4.1.1954.3.6.2.2.1.4
Timer trascorso il quale l'apparato inizia la procedura di richiesta connessione con la trama di contatto TEST. Valori ammessi da 10.... 600.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802LinkT203 1.3.6.1.4.1.1954.3.6.2.2.1.5
Configurazione timer T203. Valori ammessi da 10....600.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802LinkN200 1.3.6.1.4.1.1954.3.6.2.2.1.6
Valore parametro N200. Valori ammessi da 1...10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802LinkN201 1.3.6.1.4.1.1954.3.6.2.2.1.7
Valore parametro N201.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802LinkK 1.3.6.1.4.1.1954.3.6.2.2.1.8
Valore parametro K. Valore ammessi da 1...127.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802LinkEthDst 1.3.6.1.4.1.1954.3.6.2.2.1.9
Indirizzo MAC destinatario
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

i802LinkEthSrc 1.3.6.1.4.1.1954.3.6.2.2.1.10
Indirizzo MAC sorgente
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

i802LinkNuaDst 1.3.6.1.4.1.1954.3.6.2.2.1.11
Nua destinatario utilizzato dal link X25 connesso.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

i802LinkSsap 1.3.6.1.4.1.1954.3.6.2.2.1.12
SAP sorgente. Valori ammessi 04, 08, 0C.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802LinkDsap 1.3.6.1.4.1.1954.3.6.2.2.1.13
SAP destinatario. Valori ammessi 04, 08, 0C.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

i802OpTable 1.3.6.1.4.1.1954.3.6.2.3
Questa tabella indicizzata sull'interfaccia e sul link 802.2 riassume le principali informazioni sullo stato operativo del link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    I802OpEntry

i802OpEntry 1.3.6.1.4.1.1954.3.6.2.3.1
Entry Operativa 802.2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  I802OpEntry  

i802OpIfc 1.3.6.1.4.1.1954.3.6.2.3.1.1
Indice dell'interfaccia 802.2 corrisponde a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  


i802OpLanMode 1.3.6.1.4.1.1954.3.6.2.3.1.3
Modalita` lavoro a livello MAC: 802.3 / Ethernet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER modalita-802-3(1), modalita-ETHERNET(2)  

i802OpLanState 1.3.6.1.4.1.1954.3.6.2.3.1.4
Stato corrente del protocollo 802.2 lato interfaccia Lan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disconnected(3), await-Est(4), await-Rel(5), established(6), broadcast(8), rej-sent(9), remote-busy(10), local-busy(11), busy-TXRX(12)  

i802OpWanState 1.3.6.1.4.1.1954.3.6.2.3.1.5
Stato corrente della connessione lato interfaccia Wan
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no-CONNECTIONS(0), up-EST(1), low-AWAITS-CONN(2), up-LOW-EST(3), low-AWAITS-DISC(4), up-DISC-LOW-NOT-YET(5), up-D-LOW-WCNT(6), up-WCON-LOW-CNT(7), up-WDISC-LOW-DISC(8), up-WCON-LOW-DISC(9)  

i802OpIdbIdnRx 1.3.6.1.4.1.1954.3.6.2.3.1.6
IdBlock IdNumber relativi all'ultima trama XID ricevuta da Lan. Valore 0xffffffff all'inizializzazione o alla chiusura di sessione.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

i802OpIdbIdnTx 1.3.6.1.4.1.1954.3.6.2.3.1.7
Riporta i valori dei campiIdBlock IdNumber presenti nell'ultima trama XID trasmessa sull' interfaccia Lan. Valore 0xffffffff all'inizializzazione o alla chiusura di sessione.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

i802StatTable 1.3.6.1.4.1.1954.3.6.2.4
Questa tabella indicizzata per interfaccia e link riporta contatori statistici relativi al link 802.2. La tabella viene azzerata in seguito a errori di protocollo irreversibili (es: ricezione DM non sol- lecitato etc).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    I802StatEntry

i802StatEntry 1.3.6.1.4.1.1954.3.6.2.4.1
Entry statistiche 802.2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  I802StatEntry  

i802StatIfc 1.3.6.1.4.1.1954.3.6.2.4.1.1
Indice dell'interfaccia 802.2, corrisponde a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  


i802InfoTx 1.3.6.1.4.1.1954.3.6.2.4.1.3
Contatore delle Info trasmesse
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802RnrTx 1.3.6.1.4.1.1954.3.6.2.4.1.4
Contatore RNR trasmessi.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802RejTx 1.3.6.1.4.1.1954.3.6.2.4.1.5
Contatore REJ trasmessi.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802SabmeTx 1.3.6.1.4.1.1954.3.6.2.4.1.6
Contatore SABME trasmessi.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802DiscTx 1.3.6.1.4.1.1954.3.6.2.4.1.7
Contatore DISC trasmessi.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802XidTx 1.3.6.1.4.1.1954.3.6.2.4.1.8
Contatore XID trasmessi.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802TestTx 1.3.6.1.4.1.1954.3.6.2.4.1.9
Contatore TEST trasmessi.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802UiTx 1.3.6.1.4.1.1954.3.6.2.4.1.10
Contatore UI trasmessi.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802FrmrTx 1.3.6.1.4.1.1954.3.6.2.4.1.11
Contatore FRMR trasmessi.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802RnrTxTime 1.3.6.1.4.1.1954.3.6.2.4.1.12
Tempo di sistema relativo all'ultima trama RNR trasmessa.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

i802NRitr 1.3.6.1.4.1.1954.3.6.2.4.1.13
Contatore numero ritrasmissioni.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802InfoRx 1.3.6.1.4.1.1954.3.6.2.4.1.14
Contatore delle Info ricevute
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802RnrRx 1.3.6.1.4.1.1954.3.6.2.4.1.15
Contatore RNR ricevuti.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802RejRx 1.3.6.1.4.1.1954.3.6.2.4.1.16
Contatore REJ ricevuti.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802SabmeRx 1.3.6.1.4.1.1954.3.6.2.4.1.17
Contatore SABME ricevuti.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802DiscRx 1.3.6.1.4.1.1954.3.6.2.4.1.18
Contatore DISC ricevuti.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802XidRx 1.3.6.1.4.1.1954.3.6.2.4.1.19
Contatore XID ricevuti.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802TestRx 1.3.6.1.4.1.1954.3.6.2.4.1.20
Contatore TEST ricevuti.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802UiRx 1.3.6.1.4.1.1954.3.6.2.4.1.21
Contatore UI ricevuti.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802FrmrRx 1.3.6.1.4.1.1954.3.6.2.4.1.22
Contatore FRMR ricevuti.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

i802RnrRxTime 1.3.6.1.4.1.1954.3.6.2.4.1.23
Tempo di sistema relativa all'ultime trama RNR ricevuta.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

x28Diag 1.3.6.1.4.1.1954.3.7.2
OBJECT IDENTIFIER    

x28CnfTable 1.3.6.1.4.1.1954.3.7.2.1
Questa tabella riassume i parametri di configurazione X28 di un'interfaccia.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    X28CnfEntry

x28CnfEntry 1.3.6.1.4.1.1954.3.7.2.1.1
Entry tabella X28CnfTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  X28CnfEntry  

x28CnfIfc 1.3.6.1.4.1.1954.3.7.2.1.1.1
Indice dell'interfaccia su cui e` configurata l'entita` X28. corrisponde a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar1 1.3.6.1.4.1.1954.3.7.2.1.1.2
Parametro 1 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar2 1.3.6.1.4.1.1954.3.7.2.1.1.3
Parametro 2 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar3 1.3.6.1.4.1.1954.3.7.2.1.1.4
Parametro 3 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar4 1.3.6.1.4.1.1954.3.7.2.1.1.5
Parametro 4 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar5 1.3.6.1.4.1.1954.3.7.2.1.1.6
Parametro 5 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar6 1.3.6.1.4.1.1954.3.7.2.1.1.7
Parametro 6 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar7 1.3.6.1.4.1.1954.3.7.2.1.1.8
Parametro 7 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar8 1.3.6.1.4.1.1954.3.7.2.1.1.9
Parametro 8 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar9 1.3.6.1.4.1.1954.3.7.2.1.1.10
Parametro 9 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar10 1.3.6.1.4.1.1954.3.7.2.1.1.11
Parametro 10 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar11 1.3.6.1.4.1.1954.3.7.2.1.1.12
Parametro 11 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar12 1.3.6.1.4.1.1954.3.7.2.1.1.13
Parametro 12 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar13 1.3.6.1.4.1.1954.3.7.2.1.1.14
Parametro 13 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar14 1.3.6.1.4.1.1954.3.7.2.1.1.15
Parametro 14 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar15 1.3.6.1.4.1.1954.3.7.2.1.1.16
Parametro 15 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar16 1.3.6.1.4.1.1954.3.7.2.1.1.17
Parametro 16 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar17 1.3.6.1.4.1.1954.3.7.2.1.1.18
Parametro 17 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar18 1.3.6.1.4.1.1954.3.7.2.1.1.19
Parametro 18 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar19 1.3.6.1.4.1.1954.3.7.2.1.1.20
Parametro 19 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar20 1.3.6.1.4.1.1954.3.7.2.1.1.21
Parametro 20 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar21 1.3.6.1.4.1.1954.3.7.2.1.1.22
Parametro 21 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfPar22 1.3.6.1.4.1.1954.3.7.2.1.1.23
Parametro 22 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28CnfParity 1.3.6.1.4.1.1954.3.7.2.1.1.24
Parita' X28 configurata
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER even(0), odd(1), mark(2), space(3)  

x28OpTable 1.3.6.1.4.1.1954.3.7.2.2
Tabella dei parametri operativi su una interfaccia X28.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    X28OpEntry

x28OpEntry 1.3.6.1.4.1.1954.3.7.2.2.1
Entry tabella X28OpTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  X28OpEntry  

x28OpIfc 1.3.6.1.4.1.1954.3.7.2.2.1.1
Indice dell'interfaccia su cui e` configurata l'entita` X28, corrisponde a ifIndex della MIB II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar1 1.3.6.1.4.1.1954.3.7.2.2.1.2
Parametro 1 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar2 1.3.6.1.4.1.1954.3.7.2.2.1.3
Parametro 2 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar3 1.3.6.1.4.1.1954.3.7.2.2.1.4
Parametro 3 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar4 1.3.6.1.4.1.1954.3.7.2.2.1.5
Parametro 4 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar5 1.3.6.1.4.1.1954.3.7.2.2.1.6
Parametro 5 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar6 1.3.6.1.4.1.1954.3.7.2.2.1.7
Parametro 6 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar7 1.3.6.1.4.1.1954.3.7.2.2.1.8
Parametro 7 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar8 1.3.6.1.4.1.1954.3.7.2.2.1.9
Parametro 8 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar9 1.3.6.1.4.1.1954.3.7.2.2.1.10
Parametro 9 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar10 1.3.6.1.4.1.1954.3.7.2.2.1.11
Parametro 10 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar11 1.3.6.1.4.1.1954.3.7.2.2.1.12
Parametro 11 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar12 1.3.6.1.4.1.1954.3.7.2.2.1.13
Parametro 12 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar13 1.3.6.1.4.1.1954.3.7.2.2.1.14
Parametro 13 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar14 1.3.6.1.4.1.1954.3.7.2.2.1.15
Parametro 14 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar15 1.3.6.1.4.1.1954.3.7.2.2.1.16
Parametro 15 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar16 1.3.6.1.4.1.1954.3.7.2.2.1.17
Parametro 16 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar17 1.3.6.1.4.1.1954.3.7.2.2.1.18
Parametro 17 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar18 1.3.6.1.4.1.1954.3.7.2.2.1.19
Parametro 18 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar19 1.3.6.1.4.1.1954.3.7.2.2.1.20
Parametro 19 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar20 1.3.6.1.4.1.1954.3.7.2.2.1.21
Parametro 20 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar21 1.3.6.1.4.1.1954.3.7.2.2.1.22
Parametro 21 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpPar22 1.3.6.1.4.1.1954.3.7.2.2.1.23
Parametro 22 profilo X28
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

x28OpParity 1.3.6.1.4.1.1954.3.7.2.2.1.24
Parita' X28 configurata
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER even(0), odd(1), mark(2), space(3)  

x28OpState 1.3.6.1.4.1.1954.3.7.2.2.1.25
Stato interfaccia
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pad-Waiting(0), connection-in-Progress(1), waiting-Command(2), data-Transfer(3), disconnection-in-Progress(4)  

x28OpParityErr 1.3.6.1.4.1.1954.3.7.2.2.1.26
Contatore errori parita'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

x28OpIfcDest 1.3.6.1.4.1.1954.3.7.2.2.1.27
Indice (ifIndex) interfaccia connessa
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fryDiag 1.3.6.1.4.1.1954.3.8.2
OBJECT IDENTIFIER    

frDlcmiTable 1.3.6.1.4.1.1954.3.8.2.1
The Parameters for the Data Link Connection Management Interface for the frame relay service on this interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDlcmiEntry

frDlcmiEntry 1.3.6.1.4.1.1954.3.8.2.1.1
The Parameters for a particular Data Link Con- nection Management Interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDlcmiEntry  

frDlcmiIfIndex 1.3.6.1.4.1.1954.3.8.2.1.1.1
The ifIndex value of the corresponding ifEn- try.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frDlcmiState 1.3.6.1.4.1.1954.3.8.2.1.1.2
This variable states which Data Link Connec- tion Management scheme is active (and by impli- cation, what DLCI it uses) on the Frame Relay interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noLmiConfigured(1), lmiRev1(2), ansiT1-617-D(3), ansiT1-617-B(4), itutX36(5)  

frDlcmiAddress 1.3.6.1.4.1.1954.3.8.2.1.1.3
This variable states which address format is in use on the Frame Relay interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER q921(1), q922March90(2), q922November90(3), q922(4)  

frDlcmiAddressLen 1.3.6.1.4.1.1954.3.8.2.1.1.4
This variable states which address length in octets. In the case of Q922 format, the length indicates the entire length of the address in- cluding the control portion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER two-octets(2), three-octets(3), four-octets(4)  

frDlcmiPollingInterval 1.3.6.1.4.1.1954.3.8.2.1.1.5
This is the number of seconds between succes- sive status enquiry messages.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..30  

frDlcmiFullEnquiryInterval 1.3.6.1.4.1.1954.3.8.2.1.1.6
Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

frDlcmiErrorThreshold 1.3.6.1.4.1.1954.3.8.2.1.1.7
This is the maximum number of unanswered Status Enquiries the equipment shall accept be- fore declaring the interface down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

frDlcmiMonitoredEvents 1.3.6.1.4.1.1954.3.8.2.1.1.8
This is the number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvents' number of events the station receives 'ErrorThreshold' number of errors, the interface is marked as down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

frDlcmiMaxSupportedVCs 1.3.6.1.4.1.1954.3.8.2.1.1.9
The maximum number of Virtual Circuits allowed for this interface. Usually dictated by the Frame Relay network. In response to a SET, if a value less than zero or higher than the agent's maximal capability is configured, the agent should respond bad- Value
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frDlcmiMulticast 1.3.6.1.4.1.1954.3.8.2.1.1.10
This indicates whether the Frame Relay inter- face is using a multicast service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER nonBroadcast(1), broadcast(2)  

frCircuitTable 1.3.6.1.4.1.1954.3.8.2.2
A table containing information about specific Data Link Connection Identifiers and corresponding virtual circuits.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrCircuitEntry

frCircuitEntry 1.3.6.1.4.1.1954.3.8.2.2.1
The information regarding a single Data Link Connection Identifier.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrCircuitEntry  

frCircuitIfIndex 1.3.6.1.4.1.1954.3.8.2.2.1.1
The ifIndex Value of the ifEntry this virtual circuit is layered onto.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitDlci 1.3.6.1.4.1.1954.3.8.2.2.1.2
The Data Link Connection Identifier for this virtual circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitState 1.3.6.1.4.1.1954.3.8.2.2.1.3
Indicates whether the particular virtual cir- cuit is operational. In the absence of a Data Link Connection Management Interface, virtual circuit entries (rows) may be created by set- ting virtual circuit state to 'active', or deleted by changing Circuit state to 'invalid'. Whether or not the row actually disappears is left to the implementation, so this object may actually read as 'invalid' for some arbitrary length of time. It is also legal to set the state of a virtual circuit to 'inactive' to temporarily disable a given circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), active(2), inactive(3)  

frCircuitReceivedFECNs 1.3.6.1.4.1.1954.3.8.2.2.1.4
Number of frames received from the network in- dicating forward congestion since the virtual circuit was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitReceivedBECNs 1.3.6.1.4.1.1954.3.8.2.2.1.5
Number of frames received from the network in- dicating backward congestion since the virtual circuit was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitSentFrames 1.3.6.1.4.1.1954.3.8.2.2.1.6
The number of frames sent from this virtual circuit since it was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitSentOctets 1.3.6.1.4.1.1954.3.8.2.2.1.7
The number of octets sent from this virtual circuit since it was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitReceivedFrames 1.3.6.1.4.1.1954.3.8.2.2.1.8
Number of frames received over this virtual circuit since it was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitReceivedOctets 1.3.6.1.4.1.1954.3.8.2.2.1.9
Number of octets received over this virtual circuit since it was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitCreationTime 1.3.6.1.4.1.1954.3.8.2.2.1.10
The value of sysUpTime when the virtual cir- cuit was created, whether by the Data Link Con- nection Management Interface or by a SetRe- quest.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitLastTimeChange 1.3.6.1.4.1.1954.3.8.2.2.1.11
The value of sysUpTime when last there was a change in the virtual circuit state
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitCommittedBurst 1.3.6.1.4.1.1954.3.8.2.2.1.12
This variable indicates the maximum amount of data, in bits, that the network agrees to transfer under normal conditions, during the measurement interval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

frCircuitExcessBurst 1.3.6.1.4.1.1954.3.8.2.2.1.13
This variable indicates the maximum amount of uncommitted data bits that the network will at- tempt to deliver over the measurement interval. By default, if not configured when creating the entry, the Excess Information Burst Size is set to the value of ifSpeed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

frCircuitThroughput 1.3.6.1.4.1.1954.3.8.2.2.1.14
Throughput is the average number of 'Frame Re- lay Information Field' bits transferred per second across a user network interface in one direction, measured over the measurement inter- val. If the configured committed burst rate and throughput are both non-zero, the measurement interval T=frCircuitCommittedBurst/frCircuitThroughput. If the configured committed burst rate and throughput are both zero, the measurement in- terval T=frCircuitExcessBurst/ifSpeed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

frErrTable 1.3.6.1.4.1.1954.3.8.2.3
A table containing information about Errors on the Frame Relay interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrErrEntry

frErrEntry 1.3.6.1.4.1.1954.3.8.2.3.1
The error information for a single frame relay interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrErrEntry  

frErrIfIndex 1.3.6.1.4.1.1954.3.8.2.3.1.1
The ifIndex Value of the corresponding ifEn- try.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frErrType 1.3.6.1.4.1.1954.3.8.2.3.1.2
The type of error that was last seen on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknownError(1), receiveShort(2), receiveLong(3), illegalDLCI(4), unknownDLCI(5), dlcmiProtoErr(6), dlcmiUnknownIE(7), dlcmiSequenceErr(8), dlcmiUnknownRpt(9), noErrorSinceReset(10)  

frErrData 1.3.6.1.4.1.1954.3.8.2.3.1.3
An octet string containing as much of the er- ror packet as possible. As a minimum, it must contain the Q.922 Address or as much as was delivered. It is desirable to include all in- formation up to the PDU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

frErrTime 1.3.6.1.4.1.1954.3.8.2.3.1.4
The value of sysUpTime at which the error was detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

frTrapState 1.3.6.1.4.1.1954.3.8.2.4
This variable indicates whether the system produces the frDLCIStatusChange trap.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

frDlcmiProprTable 1.3.6.1.4.1.1954.3.8.2.5
Stato dell'interfaccia Frame Relay relativamente a configurazioni opzionali quali modalita asincrona e bidirezionale
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrDlcmiProprEntry

frDlcmiProprEntry 1.3.6.1.4.1.1954.3.8.2.5.1
Parametri per una data interfaccia (configurazioni opzionali)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrDlcmiProprEntry  

frDlcmiPrIfIndex 1.3.6.1.4.1.1954.3.8.2.5.1.1
Indice dell'interfaccia su cui insiste quella logica di cui si presentano le caratteristiche.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frDlcmiPrType 1.3.6.1.4.1.1954.3.8.2.5.1.2
Tipo di interfaccia fisica su cui insiste quella logica.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER serial1(1), serial2(4)  

frDlcmiPrStatus 1.3.6.1.4.1.1954.3.8.2.5.1.3
Stato dell'interfaccia.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER service-IN(1), service-OUT(2)  

frDlcmiPrModFun 1.3.6.1.4.1.1954.3.8.2.5.1.4
Modalita` di funzionamento del DTE: DTE: modalita` tipica; DEBUG: simulazione rete (non completa solo scopo debug); TEST: senza polling.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER mod-DTE(1), mod-DEBUG(2), mod-TEST(3)  

frDlcmiPrAsyncr 1.3.6.1.4.1.1954.3.8.2.5.1.5
Abilitazione o disabilitazione della procedura di polling asincrono.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER asincrono-OFF(1), asincrono-ON(2)  

frDlcmiPrBidir 1.3.6.1.4.1.1954.3.8.2.5.1.6
Abilitazione o disabilitazione della procedura di polling bidirezionale.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bidirezionale-OFF(1), bidirezionale-ON(2)  

frDlcmiPrBidSt 1.3.6.1.4.1.1954.3.8.2.5.1.7
Stato dell'interfaccia per quanto concerne il polling in modalita` DCE.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bid-Service-IN(1), bid-Service-OUT(2)  

frDlcmiPrBidPollIntCtr 1.3.6.1.4.1.1954.3.8.2.5.1.8
Secondi che il DTE attende prima di considerare come non giunto il messaggio di enquiry dal DCE (modalita` bidirezionale).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

frDlcmiPrBidFullEnqInt 1.3.6.1.4.1.1954.3.8.2.5.1.9
Numero di messaggi di Status che il DTE si aspetta ricevere dal DCE (modalita` bidirezionale) prima di un Full Status.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

frDlcmiPrBidErrThres 1.3.6.1.4.1.1954.3.8.2.5.1.10
Numero di eventi di polling modalita` bidirezionale che il DTE attende prima di dichiarare down o up l'interfaccia.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

frDlcmiPrBidMonEv 1.3.6.1.4.1.1954.3.8.2.5.1.11
Numero di eventi di polling modalita` bidirezionale in cui vengono monitorati gli errori.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

frDlcmiPrNumDlciColl 1.3.6.1.4.1.1954.3.8.2.5.1.12
Numero di DLCI che insistono sull'interfaccia.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircuitProprTable 1.3.6.1.4.1.1954.3.8.2.6
Tabella con informazioni aggiuntive sul singolo DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FrCircuitProprEntry

frCircuitProprEntry 1.3.6.1.4.1.1954.3.8.2.6.1
Informazioni riguardanti un singolo DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FrCircuitProprEntry  

frCircPrIfIndex 1.3.6.1.4.1.1954.3.8.2.6.1.1
Valore dell'indice dell'interfaccia in cui il DLCI e` configurato.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircPrDlci 1.3.6.1.4.1.1954.3.8.2.6.1.2
Valore del DLCI a cui i dati si riferiscono.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

frCircPrMaxLunTrama 1.3.6.1.4.1.1954.3.8.2.6.1.3
Massima lunghezza della trama accettata (Tra 1600 e 4096 byte).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

frCircPrStatoBusy 1.3.6.1.4.1.1954.3.8.2.6.1.4
Mostra se il sistema ha condizioni di congestione in atto: NoCong: Nessuna Congestione; CongRete: Congestione della rete; CongDr: Congestione del Driver del Router; CongDr&Rete Congestione del Driver e della rete.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noCong(1), congRete(2), congDr(3), congDrRete(4)  

frCircPrVelInvio 1.3.6.1.4.1.1954.3.8.2.6.1.5
Valore della velocita` di invio (Kbit/s) al momento.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pppLcp 1.3.6.1.4.1.1954.3.9.1
OBJECT IDENTIFIER    


pppLinkStatusTable 1.3.6.1.4.1.1954.3.9.1.1.1
A table containing PPP-link specific variables for this PPP implementation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PppLinkStatusEntry

pppLinkStatusEntry 1.3.6.1.4.1.1954.3.9.1.1.1.1
Management information about a particular PPP Link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PppLinkStatusEntry  

pppLinkStatusPhysicalIndex 1.3.6.1.4.1.1954.3.9.1.1.1.1.1
The value of ifIndex that identifies the lower-level interface over which this PPP Link is operating. This interface would usually be an HDLC or RS-232 type of interface. If there is no lower-layer interface element, or there is no ifEntry for the element, or the element can not be identified, then the value of this object is 0. For example, suppose that PPP is operating over a serial port. This would use two entries in the ifTable. The PPP could be running over `interface' number 123 and the serial port could be running over `interface' number 987. Therefore, ifSpecific.123 would contain the OBJECT IDENTIFIER ppp pppLinkStatusPhysicalIndex.123 would contain 987, and ifSpecific.987 would contain the OBJECT IDENTIFIER for the serial-port's media- specific MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

pppLinkStatusBadAddresses 1.3.6.1.4.1.1954.3.9.1.1.1.1.2
The number of packets received with an incorrect Address Field. This Counter is a component of the ifInErrors variable that is associated with the interface that represents this PPP Link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pppLinkStatusBadControls 1.3.6.1.4.1.1954.3.9.1.1.1.1.3
The number of packets received on this link with an incorrect Control Field. This Counter is a component of the ifInErrors variable that is associated with the interface that represents this PPP Link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pppLinkStatusPacketTooLongs 1.3.6.1.4.1.1954.3.9.1.1.1.1.4
The number of received packets that have been discarded because their length exceeded the MRU. This Counter is a component of the ifInErrors variable that is associated with the interface that represents this PPP Link. NOTE, packets which are longer than the MRU but which are successfully received and processed are NOT included in this count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pppLinkStatusBadFCSs 1.3.6.1.4.1.1954.3.9.1.1.1.1.5
The number of received packets that have been discarded due to having an incorrect FCS. This Counter is a component of the ifInErrors variable that is associated with the interface that represents this PPP Link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pppLinkStatusLocalMRU 1.3.6.1.4.1.1954.3.9.1.1.1.1.6
The current value of the MRU for the local PPP Entity. This value is the MRU that the remote entity is using when sending packets to the local PPP entity. The value of this object is meaningful only when the link has reached the open state (ifOperStatus is up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483648  

pppLinkStatusRemoteMRU 1.3.6.1.4.1.1954.3.9.1.1.1.1.7
The current value of the MRU for the remote PPP Entity. This value is the MRU that the local entity is using when sending packets to the remote PPP entity. The value of this object is meaningful only when the link has reached the open state (ifOperStatus is up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483648  

pppLinkStatusLocalToPeerACCMap 1.3.6.1.4.1.1954.3.9.1.1.1.1.8
The current value of the ACC Map used for sending packets from the local PPP entity to the remote PPP entity. The value of this object is meaningful only when the link has reached the open state (ifOperStatus is up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

pppLinkStatusPeerToLocalACCMap 1.3.6.1.4.1.1954.3.9.1.1.1.1.9
The ACC Map used by the remote PPP entity when transmitting packets to the local PPP entity. The value of this object is meaningful only when the link has reached the open state (ifOperStatus is up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

pppLinkStatusLocalToRemoteProtocolCompression 1.3.6.1.4.1.1954.3.9.1.1.1.1.10
Indicates whether the local PPP entity will use Protocol Compression when transmitting packets to the remote PPP entity. The value of this object is meaningful only when the link has reached the open state (ifOperStatus is up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pppLinkStatusRemoteToLocalProtocolCompression 1.3.6.1.4.1.1954.3.9.1.1.1.1.11
Indicates whether the remote PPP entity will use Protocol Compression when transmitting packets to the local PPP entity. The value of this object is meaningful only when the link has reached the open state (ifOperStatus is up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pppLinkStatusLocalToRemoteACCompression 1.3.6.1.4.1.1954.3.9.1.1.1.1.12
Indicates whether the local PPP entity will use Address and Control Compression when transmitting packets to the remote PPP entity. The value of this object is meaningful only when the link has reached the open state (ifOperStatus is up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pppLinkStatusRemoteToLocalACCompression 1.3.6.1.4.1.1954.3.9.1.1.1.1.13
Indicates whether the remote PPP entity will use Address and Control Compression when transmitting packets to the local PPP entity. The value of this object is meaningful only when the link has reached the open state (ifOperStatus is up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pppLinkStatusTransmitFcsSize 1.3.6.1.4.1.1954.3.9.1.1.1.1.14
The size of the Frame Check Sequence (FCS) in bits that the local node will generate when sending packets to the remote node. The value of this object is meaningful only when the link has reached the open state (ifOperStatus is up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

pppLinkStatusReceiveFcsSize 1.3.6.1.4.1.1954.3.9.1.1.1.1.15
The size of the Frame Check Sequence (FCS) in bits that the remote node will generate when sending packets to the local node. The value of this object is meaningful only when the link has reached the open state (ifOperStatus is up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

pppLinkConfigTable 1.3.6.1.4.1.1954.3.9.1.1.2
A table containing the LCP configuration parameters for this PPP Link. These variables represent the initial configuration of the PPP Link. The actual values of the parameters may be changed when the link is brought up via the LCP options negotiation mechanism.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PppLinkConfigEntry

pppLinkConfigEntry 1.3.6.1.4.1.1954.3.9.1.1.2.1
Configuration information about a particular PPP Link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PppLinkConfigEntry  

pppLinkConfigInitialMRU 1.3.6.1.4.1.1954.3.9.1.1.2.1.1
The initial Maximum Receive Unit (MRU) that the local PPP entity will advertise to the remote entity. If the value of this variable is 0 then the local PPP entity will not advertise any MRU to the remote entity and the default MRU will be assumed. Changing this object will have effect when the link is next restarted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

pppLinkConfigReceiveACCMap 1.3.6.1.4.1.1954.3.9.1.1.2.1.2
The Asynchronous-Control-Character-Map (ACC) that the local PPP entity requires for use on its receive side. In effect, this is the ACC Map that is required in order to ensure that the local modem will successfully receive all characters. The actual ACC map used on the receive side of the link will be a combination of the local node's pppLinkConfigReceiveACCMap and the remote node's pppLinkConfigTransmitACCMap. Changing this object will have effect when the link is next restarted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(4)  

pppLinkConfigTransmitACCMap 1.3.6.1.4.1.1954.3.9.1.1.2.1.3
The Asynchronous-Control-Character-Map (ACC) that the local PPP entity requires for use on its transmit side. In effect, this is the ACC Map that is required in order to ensure that all characters can be successfully transmitted through the local modem. The actual ACC map used on the transmit side of the link will be a combination of the local node's pppLinkConfigTransmitACCMap and the remote node's pppLinkConfigReceiveACCMap. Changing this object will have effect when the link is next restarted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(4)  

pppLinkConfigMagicNumber 1.3.6.1.4.1.1954.3.9.1.1.2.1.4
If true(2) then the local node will attempt to perform Magic Number negotiation with the remote node. If false(1) then this negotiation is not performed. In any event, the local node will comply with any magic number negotiations attempted by the remote node, per the PPP specification. Changing this object will have effect when the link is next restarted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pppLinkConfigFcsSize 1.3.6.1.4.1.1954.3.9.1.1.2.1.5
The size of the FCS, in bits, the local node will attempt to negotiate for use with the remote node. Regardless of the value of this object, the local node will comply with any FCS size negotiations initiated by the remote node, per the PPP specification. Changing this object will have effect when the link is next restarted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..128  

pppSecurity 1.3.6.1.4.1.1954.3.9.2
OBJECT IDENTIFIER    

pppSecurityConfigTable 1.3.6.1.4.1.1954.3.9.2.2
Table containing the configuration and preference parameters for PPP Security.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PppSecurityConfigEntry

pppSecurityConfigEntry 1.3.6.1.4.1.1954.3.9.2.2.1
Security configuration information for a particular PPP link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PppSecurityConfigEntry  


pppSecurityConfigPreference 1.3.6.1.4.1.1954.3.9.2.2.1.2
The relative preference of the security protocol identified by pppSecurityConfigProtocol. Security protocols with lower values of pppSecurityConfigPreference are tried before protocols with higher values of pppSecurityConfigPreference.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

pppSecurityConfigProtocol 1.3.6.1.4.1.1954.3.9.2.2.1.3
Identifies the security protocol to be attempted on the link identified by pppSecurityConfigLink at the preference level identified by pppSecurityConfigPreference.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OBJECT IDENTIFIER  

pppSecurityConfigStatus 1.3.6.1.4.1.1954.3.9.2.2.1.4
Setting this object to the value invalid(1) has the effect of invalidating the corresponding entry in the pppSecurityConfigTable. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant pppSecurityConfigStatus object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

pppSecuritySecretsTable 1.3.6.1.4.1.1954.3.9.2.3
Table containing the identities and secrets used by the PPP authentication protocols. As this table contains secret information, it is expected that access to this table be limited to those SNMP Party-Pairs for which a privacy protocol is in use for all SNMP messages that the parties exchange. This table contains both the ID and secret pair(s) that the local PPP entity will advertise to the remote entity and the pair(s) that the local entity will expect from the remote entity. This table allows for multiple id/secret password pairs to be specified for a particular link by using the pppSecuritySecretsIdIndex object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PppSecuritySecretsEntry

pppSecuritySecretsEntry 1.3.6.1.4.1.1954.3.9.2.3.1
Secret information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PppSecuritySecretsEntry  


pppSecuritySecretsIdIndex 1.3.6.1.4.1.1954.3.9.2.3.1.2
A unique value for each ID/Secret pair that has been defined for use on this link. This allows multiple ID/Secret pairs to be defined for each link. How the local entity selects which pair to use is a local implementation decision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

pppSecuritySecretsDirection 1.3.6.1.4.1.1954.3.9.2.3.1.3
This object defines the direction in which a particular ID/Secret pair is valid. If this object is local-to-remote then the local PPP entity will use the ID/Secret pair when attempting to authenticate the local PPP entity to the remote PPP entity. If this object is remote-to-local then the local PPP entity will expect the ID/Secret pair to be used by the remote PPP entity when the remote PPP entity attempts to authenticate itself to the local PPP entity.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER local-to-remote(1), remote-to-local(2)  

pppSecuritySecretsProtocol 1.3.6.1.4.1.1954.3.9.2.3.1.4
The security protocol (e.g. CHAP or PAP) to which this ID/Secret pair applies.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OBJECT IDENTIFIER  

pppSecuritySecretsIdentity 1.3.6.1.4.1.1954.3.9.2.3.1.5
The Identity of the ID/Secret pair. The actual format, semantics, and use of pppSecuritySecretsIdentity depends on the actual security protocol used. For example, if pppSecuritySecretsProtocol is pppSecurityPapProtocol then this object will contain a PAP Peer-ID. If pppSecuritySecretsProtocol is pppSecurityChapMD5Protocol then this object would contain the CHAP NAME parameter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

pppSecuritySecretsSecret 1.3.6.1.4.1.1954.3.9.2.3.1.6
The secret of the ID/Secret pair. The actual format, semantics, and use of pppSecuritySecretsSecret depends on the actual security protocol used. For example, if pppSecuritySecretsProtocol is pppSecurityPapProtocol then this object will contain a PAP Password. If pppSecuritySecretsProtocol is pppSecurityChapMD5Protocol then this object would contain the CHAP MD5 Secret.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

pppSecuritySecretsStatus 1.3.6.1.4.1.1954.3.9.2.3.1.7
Setting this object to the value invalid(1) has the effect of invalidating the corresponding entry in the pppSecuritySecretsTable. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant pppSecuritySecretsStatus object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

pppIp 1.3.6.1.4.1.1954.3.9.3
OBJECT IDENTIFIER    

pppIpTable 1.3.6.1.4.1.1954.3.9.3.1
Table containing the IP parameters and statistics for the local PPP entity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PppIpEntry

pppIpEntry 1.3.6.1.4.1.1954.3.9.3.1.1
IPCP status information for a particular PPP link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PppIpEntry  

pppIpOperStatus 1.3.6.1.4.1.1954.3.9.3.1.1.1
The operational status of the IP network protocol. If the value of this object is up then the finite state machine for the IP network protocol has reached the Opened state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER opened(1), not-opened(2)  

pppIpLocalToRemoteCompressionProtocol 1.3.6.1.4.1.1954.3.9.3.1.1.2
The IP compression protocol that the local PPP-IP entity uses when sending packets to the remote PPP-IP entity. The value of this object is meaningful only when the link has reached the open state (pppIpOperStatus is opened).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), vj-tcp(2)  

pppIpRemoteToLocalCompressionProtocol 1.3.6.1.4.1.1954.3.9.3.1.1.3
The IP compression protocol that the remote PPP-IP entity uses when sending packets to the local PPP-IP entity. The value of this object is meaningful only when the link has reached the open state (pppIpOperStatus is opened).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), vj-tcp(2)  

pppIpRemoteMaxSlotId 1.3.6.1.4.1.1954.3.9.3.1.1.4
The Max-Slot-Id parameter that the remote node has advertised and that is in use on the link. If vj-tcp header compression is not in use on the link then the value of this object shall be 0. The value of this object is meaningful only when the link has reached the open state (pppIpOperStatus is opened).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

pppIpLocalMaxSlotId 1.3.6.1.4.1.1954.3.9.3.1.1.5
The Max-Slot-Id parameter that the local node has advertised and that is in use on the link. If vj-tcp header compression is not in use on the link then the value of this object shall be 0. The value of this object is meaningful only when the link has reached the open state (pppIpOperStatus is opened).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

pppIpConfigTable 1.3.6.1.4.1.1954.3.9.3.2
Table containing configuration variables for the IPCP for the local PPP entity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PppIpConfigEntry

pppIpConfigEntry 1.3.6.1.4.1.1954.3.9.3.2.1
IPCP information for a particular PPP link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PppIpConfigEntry  

pppIpConfigAdminStatus 1.3.6.1.4.1.1954.3.9.3.2.1.1
The immediate desired status of the IP network protocol. Setting this object to open will inject an administrative open event into the IP network protocol's finite state machine. Setting this object to close will inject an administrative close event into the IP network protocol's finite state machine.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER open(1), close(2)  

pppIpConfigCompression 1.3.6.1.4.1.1954.3.9.3.2.1.2
If none(1) then the local node will not attempt to negotiate any IP Compression option. Otherwise, the local node will attempt to negotiate compression mode indicated by the enumerated value. Changing this object will have effect when the link is next restarted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), vj-tcp(2)  

profile 1.3.6.1.4.1.1954.4.1
OBJECT IDENTIFIER    

profileConf 1.3.6.1.4.1.1954.4.1.1
OBJECT IDENTIFIER    

profileOp 1.3.6.1.4.1.1954.4.1.2
OBJECT IDENTIFIER    

profileTable 1.3.6.1.4.1.1954.4.1.1.1
Questa tabella contiene i parametri di configurazione dei profili.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProfileEntry

profileEntry 1.3.6.1.4.1.1954.4.1.1.1.1
Entry tabella ProfileTab
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ProfileEntry  

profileId 1.3.6.1.4.1.1954.4.1.1.1.1.1
Profile Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

profileName 1.3.6.1.4.1.1954.4.1.1.1.1.2
Profile Name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileISDNPhone1 1.3.6.1.4.1.1954.4.1.1.1.1.3
ISDN Phone Number 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileISDNPhone2 1.3.6.1.4.1.1954.4.1.1.1.1.4
ISDN Phone Number 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileISDNPhone3 1.3.6.1.4.1.1954.4.1.1.1.1.5
ISDN Phone Number 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileISDNPhone4 1.3.6.1.4.1.1954.4.1.1.1.1.6
ISDN Phone Number 4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileISDNPhone5 1.3.6.1.4.1.1954.4.1.1.1.1.7
ISDN Phone Number 5.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileGatewayIP 1.3.6.1.4.1.1954.4.1.1.1.1.8
Profile IP Gateway.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

profileAutUsername 1.3.6.1.4.1.1954.4.1.1.1.1.9
Profile Chap/Pap Username.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileAutPassword 1.3.6.1.4.1.1954.4.1.1.1.1.10
Profile Chap/Pap Password.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileAutPeerUsername 1.3.6.1.4.1.1954.4.1.1.1.1.11
Profile Chap/Pap PeerUsername.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileAutPeerPassword 1.3.6.1.4.1.1954.4.1.1.1.1.12
Profile Chap/Pap Peer Password.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileAutPAP 1.3.6.1.4.1.1954.4.1.1.1.1.13
Profile PAP protocol status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER authentication-PAP-OFF(0), authentication-PAP-ON(1)  

profileAutCHAP 1.3.6.1.4.1.1954.4.1.1.1.1.14
Profile Chap protocol status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER authentication-CHAP-OFF(0), authentication-CHAP-ON(1)  

profileRemoteMASK 1.3.6.1.4.1.1954.4.1.1.1.1.15
Profile IP Remote Mask.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

profileDefault 1.3.6.1.4.1.1954.4.1.1.1.1.16
Default Profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER default-Profile-Off(0), default-Profile-On(1)  

profileDynamic 1.3.6.1.4.1.1954.4.1.1.1.1.17
Dynamic IP Profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dynamic-Off(0), dynamic-On(1)  

profileCallbackType 1.3.6.1.4.1.1954.4.1.1.1.1.18
Profile Callback Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ppp-type(0), isdn-type(1)  

profileUnnumbered 1.3.6.1.4.1.1954.4.1.1.1.1.19
Unnumbered Profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unnumbered-Off(0), unnumbered-On(1)  

profileCalled 1.3.6.1.4.1.1954.4.1.1.1.1.20
Called Profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER called-Off(0), called-On(1)  

profileCalling 1.3.6.1.4.1.1954.4.1.1.1.1.21
Calling Profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER calling-Off(0), calling-On(1)  

profileDefgtw 1.3.6.1.4.1.1954.4.1.1.1.1.22
Default gateway connection Profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER connection-to-defgtw-Off(0), connection-to-defgtw-On(1)  

profileNat 1.3.6.1.4.1.1954.4.1.1.1.1.23
Nat function on Profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER nat-Off(0), nat-On(1)  

profileCallbackReq 1.3.6.1.4.1.1954.4.1.1.1.1.24
Callback request status on Profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER callback-Request-Off(0), callback-Request-On(1)  

profileCallbackAccept 1.3.6.1.4.1.1954.4.1.1.1.1.25
Callback Accept status on Profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER callback-Accept-Off(0), callback-Accept-On(1)  

profileRemoteMaskAuto 1.3.6.1.4.1.1954.4.1.1.1.1.26
Automatic Remote Mask acquisition status
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER remoteMask-Auto-Off(0), remoteMask-Auto-On(1)  

profileDynamicRemoteNet 1.3.6.1.4.1.1954.4.1.1.1.1.27
Automatic Remote Network acquisition status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER remote-Network-acquisition-Off(0), remote-Network-acquisition-On(1)  

profileMPP 1.3.6.1.4.1.1954.4.1.1.1.1.28
Multilink PPP status on profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER mPP-Off(0), mPP-On(1)  

profileCallbackTimer 1.3.6.1.4.1.1954.4.1.1.1.1.29
Callback Timer on profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

profileRemoteIp 1.3.6.1.4.1.1954.4.1.1.1.1.30
Profile remote ip.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

profileRemotePool 1.3.6.1.4.1.1954.4.1.1.1.1.31
Profile remote pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileCounterCallIn 1.3.6.1.4.1.1954.4.1.1.1.1.32
Counter call incoming on profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

profileCounterCallOut 1.3.6.1.4.1.1954.4.1.1.1.1.33
Counter call outgoing on profile
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

profileLastCallDirection 1.3.6.1.4.1.1954.4.1.1.1.1.34
Profile last call direction.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileLastCallTimeOpen 1.3.6.1.4.1.1954.4.1.1.1.1.35
Profile last call time open.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileLastCallTimeClose 1.3.6.1.4.1.1954.4.1.1.1.1.36
Profile last call time close.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileStatus 1.3.6.1.4.1.1954.4.1.1.1.1.37
Profile status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileRunTable 1.3.6.1.4.1.1954.4.1.2.1
Questa tabella contiene i parametri run dei profili.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProfileRunEntry

profileRunEntry 1.3.6.1.4.1.1954.4.1.2.1.1
Entry tabella ProfileTabRun
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ProfileRunEntry  

profileIdRun 1.3.6.1.4.1.1954.4.1.2.1.1.1
Profile Run Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

profileIdFather 1.3.6.1.4.1.1954.4.1.2.1.1.2
IndexFather of Profile Run.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

profileFatherName 1.3.6.1.4.1.1954.4.1.2.1.1.3
NameFather of Profile Run.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileISDNPhoneUsed 1.3.6.1.4.1.1954.4.1.2.1.1.4
ISDN Phone Number Used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileIPGateway 1.3.6.1.4.1.1954.4.1.2.1.1.5
Profile Run IP Gateway.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

profileNumberChannelActive 1.3.6.1.4.1.1954.4.1.2.1.1.6
Number of channels active on profile run
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

profileIndexChannelActive 1.3.6.1.4.1.1954.4.1.2.1.1.7
Index of channels actived on profile run.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

profileConnectionTimeForChannel 1.3.6.1.4.1.1954.4.1.2.1.1.8
Connection Time on channel actived on profile run.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

authTrap 36864
Viene inviata da un apparato nel caso in cui fallisca la procedura di autenticazione con un entita di pari livello.
TRAP-TYPE    

signTrap 37120
Viene inviata da un apparato che implementa il servizio di firma nel caso in cui fallisca il controllo della firma in un pacchetto ricevuto.
TRAP-TYPE    

accessTrap 37376
Viene inviata da un apparato quando c'e un tentativo di accesso non autorizzato.
TRAP-TYPE    

badCRCTrap 37632
Se implementato il servizio di integrita dei dati viene inviata nel caso in cui il segmento decifrato abbia un CRC errato.
TRAP-TYPE    

badChainTrap 37888
Se implementato il servizio di concatenazione dei segmenti cifrati viene inviata nel caso in cui un segmento decifrato abbia un numero di sequenza errato.
TRAP-TYPE    

badAgendTrap 38144
Viene inviata nel caso in cui l'agenda delle chiavi pubbliche non sia integra (ad esempio fallisce il controllo del CRC sul file agenda.
TRAP-TYPE    

rxRstTrap 38656
Viene inviata da un apparato che riceva un RESET su un circuito virtuale X.25 di tipo switched su cui sia configurata la sicurezza X.25.
TRAP-TYPE    

cGSAccessTrap 38912
Viene inviata da un apparato che abbia ricevuto un tentativo di accesso da un apparato identificato come gestore.
TRAP-TYPE    

keyGoodTrap 39424
Viene inviata da un apparato che ha generato una nuova chiave RSA.
TRAP-TYPE    

keyBadTrap 39680
Viene inviata da un apparato quando fallisce il processo di generazione di una nuova chiave RSA.
TRAP-TYPE    

keyNotWriteTrap 39936
Viene inviata da un apparato quando fallisce la scrittura di una nuova chiave RSA precedentemente generata sulla flash dell'apparato medesimo.
TRAP-TYPE    

keyWriteTrap 40192
Viene inviata da un apparato quando ha portato a termine la scrittura di una nuova chiave RSA in Flash.
TRAP-TYPE    

agNotAvailTrap 40448
Viene inviata da un apparato quando e richiesta una operazione di accesso alla flash ma tale operazione non e al momento consentita (ad esempio e in corso una operazione di scrittura in flash).
TRAP-TYPE    

keyPubReqTrap 40704
Viene inviata da un apparato che deve aprire una connessione con un altro apparato in modo sicuro ma non conosce la chiave pubblica da usare e ne fa richiesta al gestore.
TRAP-TYPE    

alarmsDownTrap 35072
Viene inviata a tempo da un apparato che dopo tre tentativi di invio di una delle trap precedetenti non ha ricevuto risposta dal gestore (il gestore alla ricezione di una trap deve settare la variabile LTC dell'apparato mittente).
TRAP-TYPE    

noiseGenTrap 35328
Viene inviata da un apparato che abbia riscontrato un non perfetto funzionamento del generatore di rumore hardware presente sulla scheda.
TRAP-TYPE    

gtwNotRespTrap 36868
Viene inviata nel caso in cui un gateway di sicurezza non abbia risposto ad una richiesta di autenticazione inviata dall'apparato.
TRAP-TYPE    

gtwCertExpTrap 36883
Viene inviata quando il certificato del gateway e' in scadenza.
TRAP-TYPE    

fryLinkVarTrap 28672
Viene inviata quando si verifica una variazione di stato (Attivo-Disattivo) su un DLCI; la trap riporta le variabili della MIB proprietaria che danno informazioni aggiuntive relativamente al DLCI in questione ed al suo stato.
TRAP-TYPE    

modifiedConfTrap 11111
Viene utilizzata dalle applicazioni del centro di gestione per comunicare l'avvenuta modifica della configurazione di un apparato.
TRAP-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor