ALTEON-TIGON-SWITCH-MIB

File: ALTEON-TIGON-SWITCH-MIB.mib (49779 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
ALTEON-ROOT-MIB

Imported symbols

enterprises mgmt NetworkAddress
IpAddress Counter Gauge
OBJECT-TYPE PhysAddress DisplayString
switch

Defined Types

AgCurCfgTrapHostEntry  
SEQUENCE    
  agCurCfgTrapHostIndx INTEGER
  agCurCfgTrapHostIpAddr IpAddress
  agCurCfgTrapHostCommString DisplayString

AgNewCfgTrapHostEntry  
SEQUENCE    
  agNewCfgTrapHostIndx INTEGER
  agNewCfgTrapHostIpAddr IpAddress
  agNewCfgTrapHostCommString DisplayString

Defined Values

hardware 1.3.6.1.4.1.1872.2.1.1
OBJECT IDENTIFIER    

agent 1.3.6.1.4.1.1872.2.1.2
OBJECT IDENTIFIER    

stats 1.3.6.1.4.1.1872.2.1.8
OBJECT IDENTIFIER    

information 1.3.6.1.4.1.1872.2.1.9
OBJECT IDENTIFIER    

altswitchTraps 1.3.6.1.4.1.1872.2.1.13
OBJECT IDENTIFIER    

operCmds 1.3.6.1.4.1.1872.2.1.14
OBJECT IDENTIFIER    

radius 1.3.6.1.4.1.1872.2.1.16
OBJECT IDENTIFIER    

agGeneral 1.3.6.1.4.1.1872.2.1.2.1
OBJECT IDENTIFIER    

agGeneralConfig 1.3.6.1.4.1.1872.2.1.2.2
OBJECT IDENTIFIER    

memStats 1.3.6.1.4.1.1872.2.1.8.12
OBJECT IDENTIFIER    

pktStats 1.3.6.1.4.1.1872.2.1.8.13
OBJECT IDENTIFIER    

mpCpuStats 1.3.6.1.4.1.1872.2.1.8.16
OBJECT IDENTIFIER    

hwPartNumber 1.3.6.1.4.1.1872.2.1.1.1
The hardware part number of the Alteon Switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

hwRevision 1.3.6.1.4.1.1872.2.1.1.2
The hardware revision. If the revision is not available, a zero length string should be returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

hwPowerSupplyStatus 1.3.6.1.4.1.1872.2.1.1.3
The status of the internal power supply.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), bad(2)  

hwRedundantPSPresent 1.3.6.1.4.1.1872.2.1.1.4
Existence of redundant power supply.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notPresent(3), present(4)  

hwRedundantPSStatus 1.3.6.1.4.1.1872.2.1.1.5
The status of the redundant power supply.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), bad(2), notPresent(3)  

hwSensor1Temp 1.3.6.1.4.1.1872.2.1.1.6
The temperature of the rear left sensor in degrees Celsius.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

hwSensor2Temp 1.3.6.1.4.1.1872.2.1.1.7
The temperature of the rear middle sensor in degrees Celsius.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

hwSensor3Temp 1.3.6.1.4.1.1872.2.1.1.8
The temperature of the front middle sensor in degrees Celsius.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

hwSensor4Temp 1.3.6.1.4.1.1872.2.1.1.9
The temperature of the front right sensor in degrees Celsius.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

agSaveConfiguration 1.3.6.1.4.1.1872.2.1.2.1.1
This is an action object to write current configuration to nonvolatile storage. When issued with the saveActive, the active configuration in flash is saved to backup in flash and then the new configuration is saved to the active configuration in flash. When issued with notSaveActive, the active configuration is NOT saved to the flash and the active configuration is overwritten with the new configuration. ok(1) is returned always when read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ok(1), saveActive(2), notSaveActive(3)  

agApplyConfiguration 1.3.6.1.4.1.1872.2.1.2.1.2
This is an action object to apply the changes made to configuration of the switch. By setting the value to apply(2), all the changes made since the last apply are written to the new_config block. other(1) is returned when this object ie read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), apply(2)  

agApplyPending 1.3.6.1.4.1.1872.2.1.2.1.3
This object, when read, gives the user information whether an apply action is needed and that the configuration has been chaged by the user actions. The user then can apply the changes by setting proper value to the object agApplyConfiguration described above.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER applyNeeded(2), noApplyNeeded(3)  

agReset 1.3.6.1.4.1.1872.2.1.2.1.4
This is an action object to reboot the agent. other(1) is returned always when read. The following values are writable: coldReset(2)... warmReset(3)...
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), coldReset(2), warmReset(3)  

agConfigForNxtReset 1.3.6.1.4.1.1872.2.1.2.1.5
The configuration information to be loaded from at next reset. The following values are writable: active(2)...active configuration block backup(3)...backup configuration block default(4)..default configuration block
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER active(2), backup(3), default(4)  

agImageForNxtReset 1.3.6.1.4.1.1872.2.1.2.1.6
The software image to be booted from at next reset. The following values are writable: image1(2)...image 1 image2(3)...image 2
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER image1(2), image2(3)  

agSoftwareVersion 1.3.6.1.4.1.1872.2.1.2.1.7
The version of the software image that is currently running on the system in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not available.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

agBootVer 1.3.6.1.4.1.1872.2.1.2.1.8
The version of the boot code in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

agImage1Ver 1.3.6.1.4.1.1872.2.1.2.1.9
The version of the software image stored in image 1 storage in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not available or there is no valid software image.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

agImage2Ver 1.3.6.1.4.1.1872.2.1.2.1.10
The version of the software image stored in image 2 storage in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not available or there is no valid software image.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

agRtcDate 1.3.6.1.4.1.1872.2.1.2.1.11
The date on the real time clock in the form of 'mm/dd/yy'. A zero length string is returned if date is not available.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

agRtcTime 1.3.6.1.4.1.1872.2.1.2.1.12
The time on the real time clock in the form of 'hh:mm:ss'. A zero length string is returned if time is not available.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

agTftpServerIpAddr 1.3.6.1.4.1.1872.2.1.2.1.13
The TFTP server IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

agTftpImageFileName 1.3.6.1.4.1.1872.2.1.2.1.14
The image file name to be downloaded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

agTftpImage 1.3.6.1.4.1.1872.2.1.2.1.15
Whether the image file should be loaded in image1 or image2 in flash.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER image1(2), image2(3)  

agTftpDownload 1.3.6.1.4.1.1872.2.1.2.1.16
This is an action object to cause to download software image according to the setup of agTftpServerIpAddr, agTftpImageFileName, agTftpImage when download(2) is issued. other(1) is returned always when read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), download(2)  

agLastSetErrorReason 1.3.6.1.4.1.1872.2.1.2.1.17
The error reason of the last SET failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

agTftpServer 1.3.6.1.4.1.1872.2.1.2.1.18
The TFTP server IP address or domain name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

agTftpCfgFileName 1.3.6.1.4.1.1872.2.1.2.1.19
The configuration file name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

agTftpDumpFileName 1.3.6.1.4.1.1872.2.1.2.1.20
The file name for core dump.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

agTftpAction 1.3.6.1.4.1.1872.2.1.2.1.21
This is an action object to perform various TFTP Get or Put functions. The TFTP sever is specified in agTftpServer object. img-get(2) - Download switch image from a specified image file (agTftpImageFileName) on the TFTP server to the destinated storage (agTftpImage). cfg-get(3) - Download switch configuration from a specified file (agTftpCfgFileName) on the TFTP server. cfg-put(4) - Upload switch configuration to a specified file (agTftpCfgFileName) on the TFTP server. dump-put(5)- Download switch core dump to a specified file (agTftpDumpFileName) on the TFTP server. other(1) is returned always when read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), img-get(2), cfg-get(3), cfg-put(4), dump-put(5)  

agTftpLastActionStatus 1.3.6.1.4.1.1872.2.1.2.1.22
The recorded status of the previous TFTP activity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

agRevert 1.3.6.1.4.1.1872.2.1.2.1.23
This is an action object to revert the unapplied changes made to the switch. By setting the value to revert(2), all the unapplied changes will be reverted. This action will copy the current_config to the new_config block. other(1) is returned when this object is read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), revert(2)  

agRevertApply 1.3.6.1.4.1.1872.2.1.2.1.24
This is an action object to revert the unsaved changes made to the switch. By setting the value to revertApply(2), all the unsaved as well as unapplied changes will be reverted. other(1) is returned when this object is read.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), revertApply(2)  

agEnabledSwFeatures 1.3.6.1.4.1.1872.2.1.2.1.25
The software features that are enabled on the switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

agClrSyslogMsgs 1.3.6.1.4.1.1872.2.1.2.1.26
Clears all current Syslog messages.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

agSavePending 1.3.6.1.4.1.1872.2.1.2.1.27
This object, when read, gives the user information whether an save action is needed and that the configuration has been applied but not saved to the flash.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER saveNeeded(1), noSaveNeeded(2)  

agEnabledGslbKey 1.3.6.1.4.1.1872.2.1.2.1.28
Query if software key Global slb enabled on switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agEnabledBwmKey 1.3.6.1.4.1.1872.2.1.2.1.29
Query if software key Bandwidth Mgmt. enabled on switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agSlotNumber 1.3.6.1.4.1.1872.2.1.2.1.30
Identifies the slot in which this switch is installed. If the agent implementing this MIB is not a blade in a chassis this value has no meaning.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

agEnabledRurlKey 1.3.6.1.4.1.1872.2.1.2.1.31
The status of the RURL software key.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogHost 1.3.6.1.4.1.1872.2.1.2.2.1
The syslog host IP address, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

agCurCfgSyslogHost 1.3.6.1.4.1.1872.2.1.2.2.2
The syslog host IP address, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

agNewCfgBootp 1.3.6.1.4.1.1872.2.1.2.2.3
Enable or disable the use of BootP, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

agCurCfgBootp 1.3.6.1.4.1.1872.2.1.2.2.4
Enable or disable the use of BootP, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

agNewCfgSpanningTree 1.3.6.1.4.1.1872.2.1.2.2.5
Turn On or Off Spanning Tree Protocol for the switch, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(2), off(3)  

agCurCfgSpanningTree 1.3.6.1.4.1.1872.2.1.2.2.6
The state of Spanning Tree Protocol for the switch, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(2), off(3)  

agTrapHostTableMaxEnt 1.3.6.1.4.1.1872.2.1.2.2.7
The maximum number of rows in the trap host table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

agCurCfgTrapHostTable 1.3.6.1.4.1.1872.2.1.2.2.8
The table of trap hosts which to send SNMP traps in the current_configuration block.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgCurCfgTrapHostEntry

agCurCfgTrapHostEntry 1.3.6.1.4.1.1872.2.1.2.2.8.1
A row in the trap host table in the current_configuration block.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AgCurCfgTrapHostEntry  

agCurCfgTrapHostIndx 1.3.6.1.4.1.1872.2.1.2.2.8.1.1
The index of the row in trap host table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

agCurCfgTrapHostIpAddr 1.3.6.1.4.1.1872.2.1.2.2.8.1.2
The IP address of a trap host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

agCurCfgTrapHostCommString 1.3.6.1.4.1.1872.2.1.2.2.8.1.3
The SNMP community string to use with the trap host
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

agNewCfgTrapHostTable 1.3.6.1.4.1.1872.2.1.2.2.9
The table of trap hosts which to send SNMP traps in the new_configuration block.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AgNewCfgTrapHostEntry

agNewCfgTrapHostEntry 1.3.6.1.4.1.1872.2.1.2.2.9.1
A row in the trap host table in the new_configuration block.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AgNewCfgTrapHostEntry  

agNewCfgTrapHostIndx 1.3.6.1.4.1.1872.2.1.2.2.9.1.1
The index of the row in trap host table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

agNewCfgTrapHostIpAddr 1.3.6.1.4.1.1872.2.1.2.2.9.1.2
The IP address of a trap host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

agNewCfgTrapHostCommString 1.3.6.1.4.1.1872.2.1.2.2.9.1.3
The SNMP community string to use with the trap host
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

agCurCfgHttpServerPort 1.3.6.1.4.1.1872.2.1.2.2.10
The TCP port number that the HTTP server is listening to in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

agNewCfgHttpServerPort 1.3.6.1.4.1.1872.2.1.2.2.11
The TCP port number that the HTTP server is listening to in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

agCurCfgLoginBanner 1.3.6.1.4.1.1872.2.1.2.2.12
The user defined login banner.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..79)  

agNewCfgLoginBanner 1.3.6.1.4.1.1872.2.1.2.2.13
The user defined login banner.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..79)  

agNewCfgSyslog2Host 1.3.6.1.4.1.1872.2.1.2.2.14
The second syslog host IP address, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

agCurCfgSyslog2Host 1.3.6.1.4.1.1872.2.1.2.2.15
The second syslog host IP address, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

agCurCfgSyslogFac 1.3.6.1.4.1.1872.2.1.2.2.16
The facility of syslog host in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8)  

agNewCfgSyslogFac 1.3.6.1.4.1.1872.2.1.2.2.17
The facility of syslog host in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8)  

agCurCfgSyslog2Fac 1.3.6.1.4.1.1872.2.1.2.2.18
The facility of syslog2 host in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8)  

agNewCfgSyslog2Fac 1.3.6.1.4.1.1872.2.1.2.2.19
The facility of syslogs host in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8)  

agCurCfgSmtpHost 1.3.6.1.4.1.1872.2.1.2.2.20
The user defined SMTP host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

agNewCfgSmtpHost 1.3.6.1.4.1.1872.2.1.2.2.21
The user defined SMTP host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

agCurCfgConsole 1.3.6.1.4.1.1872.2.1.2.2.22
Enable or disable console output of syslog messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgConsole 1.3.6.1.4.1.1872.2.1.2.2.23
Enable or disable console output of syslog messages.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgMgmtNetwork 1.3.6.1.4.1.1872.2.1.2.2.24
The management network - corresponding to the mnet command of the slb configuration menu.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

agNewCfgMgmtNetwork 1.3.6.1.4.1.1872.2.1.2.2.25
The management network - corresponding to the mnet command of the system menu.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

agCurCfgMgmtMask 1.3.6.1.4.1.1872.2.1.2.2.26
The management subnet mask - corresponding to the mmask command of the system configuration menu.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

agNewCfgMgmtMask 1.3.6.1.4.1.1872.2.1.2.2.27
The management subnet mask - corresponding to the mmask command of the system configuration menu.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

agNTP 1.3.6.1.4.1.1872.2.1.2.2.28
OBJECT IDENTIFIER    

agCurCfgNTPServer 1.3.6.1.4.1.1872.2.1.2.2.28.1
The NTP Server Address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

agNewCfgNTPServer 1.3.6.1.4.1.1872.2.1.2.2.28.2
The NTP Server Address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

agCurCfgNTPResyncInterval 1.3.6.1.4.1.1872.2.1.2.2.28.3
The NTP Server resync interval in minutes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2880  

agNewCfgNTPResyncInterval 1.3.6.1.4.1.1872.2.1.2.2.28.4
The NTP Server resync interval in minutes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2880  

agCurCfgNTPTzone 1.3.6.1.4.1.1872.2.1.2.2.28.5
The NTP Server timezone offset from GMT in hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..3)  

agNewCfgNTPTzone 1.3.6.1.4.1.1872.2.1.2.2.28.6
The NTP Server timezone offset from GMT in hours.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..3)  

agCurCfgNTPDlight 1.3.6.1.4.1.1872.2.1.2.2.28.7
Enable/disable daylight savings time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgNTPDlight 1.3.6.1.4.1.1872.2.1.2.2.28.8
Enable/disable daylight savings time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgNTPService 1.3.6.1.4.1.1872.2.1.2.2.28.9
Enable/disable NTP Service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgNTPService 1.3.6.1.4.1.1872.2.1.2.2.28.10
Enable/disable NTP Service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agLog 1.3.6.1.4.1.1872.2.1.2.2.29
OBJECT IDENTIFIER    

agNewCfgSyslogTrapConsole 1.3.6.1.4.1.1872.2.1.2.2.29.1
Enable or disable console syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapConsole 1.3.6.1.4.1.1872.2.1.2.2.29.2
Enable or disable console syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapSystem 1.3.6.1.4.1.1872.2.1.2.2.29.3
Enable or disable system level syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapSystem 1.3.6.1.4.1.1872.2.1.2.2.29.4
Enable or disable system level syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapMgmt 1.3.6.1.4.1.1872.2.1.2.2.29.5
Enable or disable management(flash, config, login) syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapMgmt 1.3.6.1.4.1.1872.2.1.2.2.29.6
Enable or disable management(flash, config, login) syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapCli 1.3.6.1.4.1.1872.2.1.2.2.29.7
Enable or disable CLI generated error syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapCli 1.3.6.1.4.1.1872.2.1.2.2.29.8
Enable or disable CLI generated error syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapStp 1.3.6.1.4.1.1872.2.1.2.2.29.9
Enable or disable spanning tree syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapStp 1.3.6.1.4.1.1872.2.1.2.2.29.10
Enable or disable spanning tree syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapVlan 1.3.6.1.4.1.1872.2.1.2.2.29.11
Enable or disable VLAN syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapVlan 1.3.6.1.4.1.1872.2.1.2.2.29.12
Enable or disable VLAN syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapSlb 1.3.6.1.4.1.1872.2.1.2.2.29.13
Enable or disable SLB syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapSlb 1.3.6.1.4.1.1872.2.1.2.2.29.14
Enable or disable SLB syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapGslb 1.3.6.1.4.1.1872.2.1.2.2.29.15
Enable or disable GSLB syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapGslb 1.3.6.1.4.1.1872.2.1.2.2.29.16
Enable or disable GSLB syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapFilter 1.3.6.1.4.1.1872.2.1.2.2.29.17
Enable or disable filter syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapFilter 1.3.6.1.4.1.1872.2.1.2.2.29.18
Enable or disable filter syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapSsh 1.3.6.1.4.1.1872.2.1.2.2.29.19
Enable or disable SSH, RADIUS syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapSsh 1.3.6.1.4.1.1872.2.1.2.2.29.20
Enable or disable SSH, RADIUS syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapVrrp 1.3.6.1.4.1.1872.2.1.2.2.29.21
Enable or disable VRRP syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapVrrp 1.3.6.1.4.1.1872.2.1.2.2.29.22
Enable or disable VRRP syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapBgp 1.3.6.1.4.1.1872.2.1.2.2.29.23
Enable or disable BGP syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapBgp 1.3.6.1.4.1.1872.2.1.2.2.29.24
Enable or disable BGP syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapNtp 1.3.6.1.4.1.1872.2.1.2.2.29.25
Enable or disable NTP syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapNtp 1.3.6.1.4.1.1872.2.1.2.2.29.26
Enable or disable NTP syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapIsd 1.3.6.1.4.1.1872.2.1.2.2.29.27
Enable or disable ISD syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapIsd 1.3.6.1.4.1.1872.2.1.2.2.29.28
Enable or disable ISD syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapIp 1.3.6.1.4.1.1872.2.1.2.2.29.31
Enable or disable IP related syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapIp 1.3.6.1.4.1.1872.2.1.2.2.29.32
Enable or disable IP related syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapWeb 1.3.6.1.4.1.1872.2.1.2.2.29.35
Enable or disable WEBUI related syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapWeb 1.3.6.1.4.1.1872.2.1.2.2.29.36
Enable or disable WEBUI related syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapSynAtk 1.3.6.1.4.1.1872.2.1.2.2.29.37
Enable or disable SYN attack detection related syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapSynAtk 1.3.6.1.4.1.1872.2.1.2.2.29.38
Enable or disable SYN attack detection related syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agNewCfgSyslogTrapTcpLim 1.3.6.1.4.1.1872.2.1.2.2.29.39
Enable or disable TCP rate limiting related syslog and SNMP trap, in the new_configuration block.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

agCurCfgSyslogTrapTcpLim 1.3.6.1.4.1.1872.2.1.2.2.29.40
Enable or disable TCP rate limiting related syslog and SNMP trap, as currently configured in the current_configuration block.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

radCurCfgPrimaryIpAddr 1.3.6.1.4.1.1872.2.1.16.1
The IP address of the Primary RADIUS server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

radNewCfgPrimaryIpAddr 1.3.6.1.4.1.1872.2.1.16.2
The IP address of the Primary RADIUS server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

radCurCfgSecondaryIpAddr 1.3.6.1.4.1.1872.2.1.16.3
The IP address of the Secondary RADIUS server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

radNewCfgSecondaryIpAddr 1.3.6.1.4.1.1872.2.1.16.4
The IP address of the Secondary RADIUS server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

radCurCfgPort 1.3.6.1.4.1.1872.2.1.16.5
Specify the RADIUS port number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1500..3000  

radNewCfgPort 1.3.6.1.4.1.1872.2.1.16.6
Speicfy the RADIUS port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1500..3000  

radCurCfgTimeout 1.3.6.1.4.1.1872.2.1.16.7
The maximum number of seconds before resending authentication to RADIUS server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

radNewCfgTimeout 1.3.6.1.4.1.1872.2.1.16.8
The maximum number of seconds before resending authentication to RADIUS server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

radCurCfgRetries 1.3.6.1.4.1.1872.2.1.16.9
Number of retries to the RADIUS server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

radNewCfgRetries 1.3.6.1.4.1.1872.2.1.16.10
Number of retries to the RADIUS server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..3  

radCurCfgState 1.3.6.1.4.1.1872.2.1.16.11
Enable or disbale RADIUS authentication.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

radNewCfgState 1.3.6.1.4.1.1872.2.1.16.12
Enable or disable RADIUS authentication.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(2), disabled(3)  

radCurCfgAuthenString 1.3.6.1.4.1.1872.2.1.16.13
The RADIUS authentication string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

radNewCfgAuthenString 1.3.6.1.4.1.1872.2.1.16.14
The RADIUS authentication string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

radCurCfgTelnet 1.3.6.1.4.1.1872.2.1.16.15
Enable or disbale RADIUS backdoor for telnet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

radNewCfgTelnet 1.3.6.1.4.1.1872.2.1.16.16
Enable or disable RADIUS backdoor for telnet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

memStatsAllocs 1.3.6.1.4.1.1872.2.1.8.12.1
The total number of memory allocations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memStatsFrees 1.3.6.1.4.1.1872.2.1.8.12.2
The total number of memory frees.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memStatsAllocFails 1.3.6.1.4.1.1872.2.1.8.12.3
The total number of memory allocations failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memStatsBytesCurr 1.3.6.1.4.1.1872.2.1.8.12.4
The outstanding memory in bytes have been allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

memStatsBytesHiwat 1.3.6.1.4.1.1872.2.1.8.12.5
Bytes allocated witch high water mark.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

memStatsPoolBytes 1.3.6.1.4.1.1872.2.1.8.12.6
The total bytes in the memory pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

memStatsLargest 1.3.6.1.4.1.1872.2.1.8.12.7
The largest block has been allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

pktStatsAllocs 1.3.6.1.4.1.1872.2.1.8.13.1
The total packets have been allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pktStatsFrees 1.3.6.1.4.1.1872.2.1.8.13.2
The total packets have been freed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pktStatsAllocFails 1.3.6.1.4.1.1872.2.1.8.13.3
The total packet allocations failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pktStatsMediums 1.3.6.1.4.1.1872.2.1.8.13.4
The number of medium size packets have been allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pktStatsJumbos 1.3.6.1.4.1.1872.2.1.8.13.5
The number of jumbo size packets have been allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pktStatsSmalls 1.3.6.1.4.1.1872.2.1.8.13.6
The number of small size packets have been allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mpCpuAStatsUtil1Second 1.3.6.1.4.1.1872.2.1.8.16.1
The utilization of MP CPU A over 1 second. It shows the percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mpCpuBStatsUtil1Second 1.3.6.1.4.1.1872.2.1.8.16.2
The utilization of MP CPU B over 4 seconds. It shows the percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mpCpuAStatsUtil4Seconds 1.3.6.1.4.1.1872.2.1.8.16.3
The utilization of MP CPU A over 4 seconds. It shows the percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mpCpuBStatsUtil4Seconds 1.3.6.1.4.1.1872.2.1.8.16.4
The utilization of MP CPU B over 4 seconds. It shows the percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mpCpuAStatsUtil64Seconds 1.3.6.1.4.1.1872.2.1.8.16.5
The utilization of MP CPU A over 64 seconds. It shows the percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mpCpuBStatsUtil64Seconds 1.3.6.1.4.1.1872.2.1.8.16.6
The utilization of MP CPU B over 64 second. It shows the percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER