ALLIEDTELESYN-MIB

File: ALLIEDTELESYN-MIB.mib (240166 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1215
RFC-1212

Imported symbols

enterprises IpAddress Counter
DisplayString ifIndex TRAP-TYPE
OBJECT-TYPE

Defined Types

InterfaceIndexOrZero  
INTEGER 0..2147483647    

FanAndPsPsuStatusEntry  
SEQUENCE    
  fanAndPsPsuNumber INTEGER
  fanAndPsPsuPresent INTEGER
  fanAndPsPsuType INTEGER
  fanAndPsPsuFan INTEGER
  fanAndPsPsuTemperature INTEGER
  fanAndPsPsuPower INTEGER

SbTempEntry  
SEQUENCE    
  sbTempIndex INTEGER
  sbTempActualTemperature INTEGER
  sbTempFixedThresholdStatus INTEGER
  sbTempSettableThresholdStatus INTEGER
  sbTempSettableThreshold INTEGER

ArBoardEntry  
SEQUENCE    
  arBoardIndex INTEGER
  arBoardId OBJECT IDENTIFIER
  arBoardName DisplayString
  arBoardRevision DisplayString
  arBoardSerialNumber DisplayString
  arBoardTotalSlots INTEGER
  arBoardTotalPositions INTEGER

ArSlotEntry  
SEQUENCE    
  arSlotBoardIndex INTEGER
  arSlotSlotIndex INTEGER
  arSlotHeldBoardIndex INTEGER
  arSlotDescription DisplayString

ArInterfaceEntry  
SEQUENCE    
  arInterfaceBoardIndex INTEGER
  arInterfacePosition INTEGER
  arInterfaceIfIndex InterfaceIndexOrZero
  arInterfaceName DisplayString
  arInterfaceFullName DisplayString

ArIfXEntry  
SEQUENCE    
  arIfXIndex INTEGER
  arIfXAverageInputBitsSecond INTEGER
  arIfXAverageInputPacketsSecond INTEGER
  arIfXAverageOutputBitsSecond INTEGER
  arIfXAverageOutputPacketsSecond INTEGER

EthIntEntry  
SEQUENCE    
  ethIntIndex INTEGER
  ethIntBoardIndex INTEGER
  ethIntBoardPosition INTEGER
  ethIntDuplexMode INTEGER

CcDetailsEntry  
SEQUENCE    
  ccDetailsIndex INTEGER
  ccDetailsName DisplayString
  ccDetailsRemoteName DisplayString
  ccDetailsCalledNumber DisplayString
  ccDetailsCallingNumber DisplayString
  ccDetailsAlternateNumber DisplayString
  ccDetailsEnabled INTEGER
  ccDetailsDirection INTEGER
  ccDetailsPrecedence INTEGER
  ccDetailsHoldupTime INTEGER
  ccDetailsPreferredIfIndex InterfaceIndexOrZero
  ccDetailsRequiredIfIndex InterfaceIndexOrZero
  ccDetailsPriority INTEGER
  ccDetailsRetryT1 INTEGER
  ccDetailsRetryN1 INTEGER
  ccDetailsRetryT2 INTEGER
  ccDetailsRetryN2 INTEGER
  ccDetailsKeepup INTEGER
  ccDetailsOutSetupCli INTEGER
  ccDetailsOutSetupUser INTEGER
  ccDetailsOutSetupCalledSub INTEGER
  ccDetailsOutSubaddress DisplayString
  ccDetailsCallback INTEGER
  ccDetailsCallbackDelay INTEGER
  ccDetailsInSetupCalledSubSearch INTEGER
  ccDetailsInSetupUserSearch INTEGER
  ccDetailsInSetupCliSearch INTEGER
  ccDetailsInSetupCliSearchList INTEGER
  ccDetailsInAnyFlag INTEGER
  ccDetailsInSetupCalledSubCheck INTEGER
  ccDetailsInSetupUserCheck INTEGER
  ccDetailsInSetupCliCheck INTEGER
  ccDetailsInSetupCliCheckList INTEGER
  ccDetailsUserType INTEGER
  ccDetailsLoginType INTEGER
  ccDetailsUsername INTEGER
  ccDetailsPassword INTEGER
  ccDetailsBumpDelay INTEGER
  ccDetailsDataRate INTEGER
  ccDetailsPppTemplate INTEGER
  ccDetailsUserModule INTEGER
  ccDetailsNumberAttachments INTEGER

CcCliListEntry  
SEQUENCE    
  ccCliListListIndex INTEGER
  ccCliListEntryIndex INTEGER
  ccCliListNumber DisplayString

CcActiveCallEntry  
SEQUENCE    
  ccActiveCallIndex INTEGER
  ccActiveCallDetailsIndex INTEGER
  ccActiveCallIfIndex InterfaceIndexOrZero
  ccActiveCallDataRate INTEGER
  ccActiveCallState INTEGER
  ccActiveCallDirection INTEGER
  ccActiveCallUserModule INTEGER
  ccActiveCallUserInstance INTEGER
  ccActiveCallBchannelIndex INTEGER

CcCallLogEntry  
SEQUENCE    
  ccCallLogIndex INTEGER
  ccCallLogName DisplayString
  ccCallLogState INTEGER
  ccCallLogTimeStarted DisplayString
  ccCallLogDirection INTEGER
  ccCallLogDuration INTEGER
  ccCallLogRemoteNumber DisplayString

CcAttachmentEntry  
SEQUENCE    
  ccAttachmentDetailsIndex INTEGER
  ccAttachmentEntryIndex INTEGER
  ccAttachmentActiveCallIndex INTEGER
  ccAttachmentUserInstance INTEGER

CcBchannelEntry  
SEQUENCE    
  ccBchannelIfIndex INTEGER
  ccBchannelChannelIndex INTEGER
  ccBchannelAllocated INTEGER
  ccBchannelCallType INTEGER
  ccBchannelActiveCallIndex INTEGER
  ccBchannelPriority INTEGER
  ccBchannelDirection INTEGER

BriIntEntry  
SEQUENCE    
  briIntIndex INTEGER
  briIntBoardIndex INTEGER
  briIntBoardPosition INTEGER
  briIntMode INTEGER
  briIntTdmChannelMap INTEGER
  briIntIsdnChannelMap INTEGER

BriChanEntry  
SEQUENCE    
  briChanIntIndex INTEGER
  briChanChannelIndex INTEGER
  briChanMode INTEGER
  briChanState INTEGER

PriIntEntry  
SEQUENCE    
  priIntIndex INTEGER
  priIntBoardIndex INTEGER
  priIntBoardPosition INTEGER
  priIntMode INTEGER
  priIntTdmChannelMap INTEGER
  priIntIsdnChannelMap INTEGER
  priIntType INTEGER

PriChanEntry  
SEQUENCE    
  priChanIntIndex INTEGER
  priChanChannelIndex INTEGER
  priChanMode INTEGER
  priChanState INTEGER

LoadEntry  
SEQUENCE    
  loadIndex INTEGER
  loadServer IpAddress
  loadDestination INTEGER
  loadFilename DisplayString
  loadDelay INTEGER

InstallEntry  
SEQUENCE    
  instIndex INTEGER
  instRelDevice INTEGER
  instRelName DisplayString
  instRelMajor INTEGER
  instRelMinor INTEGER
  instPatDevice INTEGER
  instPatName DisplayString
  instRelInterim INTEGER
  instRelExists INTEGER
  instPatExists INTEGER

InstallHistoryEntry  
SEQUENCE    
  instHistIndex INTEGER
  instHistLine DisplayString

LicenceEntry  
SEQUENCE    
  licenceIndex INTEGER
  licenceStatus INTEGER
  licenceRelease DisplayString
  licenceMajor INTEGER
  licenceMinor INTEGER
  licencePassword DisplayString
  licenceExpiry DisplayString
  licenceInterim INTEGER

FileEntry  
SEQUENCE    
  fileIndex INTEGER
  fileName DisplayString
  fileDevice INTEGER
  fileCreationTime DisplayString
  fileStatus INTEGER
  fileSize INTEGER

PingEntry  
SEQUENCE    
  pingIndex INTEGER
  pingProtocol INTEGER
  pingAddress OCTET STRING
  pingNumberOfPackets INTEGER
  pingPacketSize INTEGER
  pingTimeout INTEGER
  pingDelay INTEGER
  pingTrapOnCompletion INTEGER
  pingTypeOfService INTEGER
  pingPattern INTEGER

DhcpRangeEntry  
SEQUENCE    
  dhcpRangeIndex INTEGER
  dhcpRangeName DisplayString
  dhcpRangeBaseAddress IpAddress
  dhcpRangeNumberOfAddresses INTEGER
  dhcpRangeGateway IpAddress

DhcpClientEntry  
SEQUENCE    
  dhcpClientIpAddress IpAddress
  dhcpClientID OCTET STRING
  dhcpClientState INTEGER
  dhcpClientType INTEGER
  dhcpClientExpiry OCTET STRING

SwiPortEntry  
SEQUENCE    
  swiPortNumber INTEGER
  swiPortIngressLimit INTEGER
  swiPortEgressLimit INTEGER

Swi56xxPortCounterEntry  
SEQUENCE    
  swi56xxPortNumber INTEGER
  swi56xxRxTx64kPkts Counter
  swi56xxRxTx65To127kPkts Counter
  swi56xxRxTx128To255kPkts Counter
  swi56xxRxTx256To511kPkts Counter
  swi56xxRxTx512To1023kPkts Counter
  swi56xxRxTx1024ToMaxPktSzPkts Counter
  swi56xxRxTx519To1522kPkts Counter
  swi56xxPortRxOctets Counter
  swi56xxPortRxPkts Counter
  swi56xxPortRxFCSErrors Counter
  swi56xxPortRxMulticastPkts Counter
  swi56xxPortRxBroadcastPkts Counter
  swi56xxPortRxPauseMACCtlFrms Counter
  swi56xxPortRxOversizePkts Counter
  swi56xxPortRxFragments Counter
  swi56xxPortRxJabbers Counter
  swi56xxPortRxMACControlFrms Counter
  swi56xxPortRxUnsupportOpcode Counter
  swi56xxPortRxAlignmentErrors Counter
  swi56xxPortRxOutOfRngeLenFld Counter
  swi56xxPortRxSymErDurCarrier Counter
  swi56xxPortRxCarrierSenseErr Counter
  swi56xxPortRxUndersizePkts Counter
  swi56xxPortRxIpInHdrErrors Counter
  swi56xxPortTxOctets Counter
  swi56xxPortTxPkts Counter
  swi56xxPortTxFCSErrors Counter
  swi56xxPortTxMulticastPkts Counter
  swi56xxPortTxBroadcastPkts Counter
  swi56xxPortTxPauseMACCtlFrms Counter
  swi56xxPortTxOversizePkts Counter
  swi56xxPortTxFragments Counter
  swi56xxPortTxJabbers Counter
  swi56xxPortTxPauseCtrlFrms Counter
  swi56xxPortTxFrameWDeferrdTx Counter
  swi56xxPortTxFrmWExcesDefer Counter
  swi56xxPortTxSingleCollsnFrm Counter
  swi56xxPortTxMultCollsnFrm Counter
  swi56xxPortTxLateCollsns Counter
  swi56xxPortTxExcessivCollsns Counter
  swi56xxPortTxCollisionFrames Counter
  swi56xxPortMiscDropEvents Counter
  swi56xxPortMiscTaggedPktTx Counter
  swi56xxPortMiscTotalPktTxAbort Counter
  swi56xxPortHWMultiTTLexpired Counter
  swi56xxPortHWMultiBridgedFrames Counter
  swi56xxPortHWMultiRxDrops Counter
  swi56xxPortHWMultiTxDrops Counter

LbShowGlobalEntry  
SEQUENCE    
  lbGlobalIndex INTEGER
  lbAffinityTimeOut INTEGER
  lbOrphanTimeOut INTEGER
  lbCriticalRst INTEGER
  lbTotalResources INTEGER
  lbTotalResPools INTEGER
  lbTotalVirtBals INTEGER
  lbCurrentConnections INTEGER

LbShowResEntry  
SEQUENCE    
  lbResIndex INTEGER
  lbResource DisplayString
  lbResIp IpAddress
  lbResPort INTEGER
  lbResState DisplayString
  lbResWeight INTEGER
  lbResTotalConnections INTEGER
  lbResCurrentConnections INTEGER

LbShowResPoolEntry  
SEQUENCE    
  lbResPoolIndex INTEGER
  lbResPoolResourceIndex INTEGER
  lbResPool DisplayString
  lbResPoolSelectionAlg DisplayString
  lbResPoolFailOnLast DisplayString
  lbResPoolTotalConnections DisplayString
  lbResPoolResources DisplayString

LbShowVirtBalEntry  
SEQUENCE    
  lbVirtBalIndex INTEGER
  lbVirtBal DisplayString
  lbVirtBalPublicIp IpAddress
  lbVirtBalPublicPort INTEGER
  lbVirtBalState DisplayString
  lbVirtBalResPool DisplayString
  lbVirtBalType DisplayString
  lbVirtBalTotalConnections INTEGER
  lbVirtBalAffinity DisplayString
  lbVirtBalHttpErrorCode DisplayString

LbShowAffEntry  
SEQUENCE    
  lbAffIndex INTEGER
  lbAffVirtBal DisplayString
  lbAffClientIp IpAddress
  lbAffCookie DisplayString
  lbAffResource DisplayString
  lbAffExpiry INTEGER

LbShowConEntry  
SEQUENCE    
  lbConIndex INTEGER
  lbConVirtBal DisplayString
  lbConClientIp IpAddress
  lbConPort INTEGER
  lbConResource DisplayString

Ds3TrapEntry  
SEQUENCE    
  ds3TcaTrapEnable INTEGER
  ds3TrapError INTEGER
  ds3TrapLoc INTEGER
  ds3TrapInterval INTEGER

Defined Values

alliedTelesyn 1.3.6.1.4.1.207
OBJECT IDENTIFIER    

products 1.3.6.1.4.1.207.1
OBJECT IDENTIFIER    

mibObject 1.3.6.1.4.1.207.8
OBJECT IDENTIFIER    

bridgeRouter 1.3.6.1.4.1.207.1.1
OBJECT IDENTIFIER    

centreCOM-AR300Router 1.3.6.1.4.1.207.1.1.8
OBJECT IDENTIFIER    

centreCOM-AR720Router 1.3.6.1.4.1.207.1.1.11
OBJECT IDENTIFIER    

centreCOM-AR300LRouter 1.3.6.1.4.1.207.1.1.12
OBJECT IDENTIFIER    

centreCOM-AR310Router 1.3.6.1.4.1.207.1.1.13
OBJECT IDENTIFIER    

centreCOM-AR300LURouter 1.3.6.1.4.1.207.1.1.14
OBJECT IDENTIFIER    

centreCOM-AR300URouter 1.3.6.1.4.1.207.1.1.15
OBJECT IDENTIFIER    

centreCOM-AR310URouter 1.3.6.1.4.1.207.1.1.16
OBJECT IDENTIFIER    

centreCOM-AR350Router 1.3.6.1.4.1.207.1.1.17
OBJECT IDENTIFIER    

centreCOM-AR370Router 1.3.6.1.4.1.207.1.1.18
OBJECT IDENTIFIER    

centreCOM-AR330Router 1.3.6.1.4.1.207.1.1.19
OBJECT IDENTIFIER    

centreCOM-AR395Router 1.3.6.1.4.1.207.1.1.20
OBJECT IDENTIFIER    

centreCOM-AR390Router 1.3.6.1.4.1.207.1.1.21
OBJECT IDENTIFIER    

centreCOM-AR370URouter 1.3.6.1.4.1.207.1.1.22
OBJECT IDENTIFIER    

centreCOM-AR740Router 1.3.6.1.4.1.207.1.1.23
OBJECT IDENTIFIER    

centreCOM-AR140SRouter 1.3.6.1.4.1.207.1.1.24
OBJECT IDENTIFIER    

centreCOM-AR140URouter 1.3.6.1.4.1.207.1.1.25
OBJECT IDENTIFIER    

centreCOM-AR320Router 1.3.6.1.4.1.207.1.1.26
OBJECT IDENTIFIER    

centreCOM-AR130SRouter 1.3.6.1.4.1.207.1.1.27
OBJECT IDENTIFIER    

centreCOM-AR130URouter 1.3.6.1.4.1.207.1.1.28
OBJECT IDENTIFIER    

centreCOM-AR160Router 1.3.6.1.4.1.207.1.1.29
OBJECT IDENTIFIER    

at-AR740RouterDC 1.3.6.1.4.1.207.1.1.43
OBJECT IDENTIFIER    

centreCOM-AR120Router 1.3.6.1.4.1.207.1.1.44
OBJECT IDENTIFIER    

at-AR410Router 1.3.6.1.4.1.207.1.1.47
OBJECT IDENTIFIER    

at-AR725Router 1.3.6.1.4.1.207.1.1.48
OBJECT IDENTIFIER    

at-AR745Router 1.3.6.1.4.1.207.1.1.49
OBJECT IDENTIFIER    

at-AR410v2Router 1.3.6.1.4.1.207.1.1.50
OBJECT IDENTIFIER    

at-AR410v3Router 1.3.6.1.4.1.207.1.1.51
OBJECT IDENTIFIER    

at-AR725RouterDC 1.3.6.1.4.1.207.1.1.52
OBJECT IDENTIFIER    

at-AR745RouterDC 1.3.6.1.4.1.207.1.1.53
OBJECT IDENTIFIER    

at-AR450Router 1.3.6.1.4.1.207.1.1.54
OBJECT IDENTIFIER    

at-AR450DualRouter 1.3.6.1.4.1.207.1.1.55
OBJECT IDENTIFIER    

at-AR440Router 1.3.6.1.4.1.207.1.1.59
OBJECT IDENTIFIER    

at-AR441Router 1.3.6.1.4.1.207.1.1.60
OBJECT IDENTIFIER    

at-AR442Router 1.3.6.1.4.1.207.1.1.61
OBJECT IDENTIFIER    

at-AR443Router 1.3.6.1.4.1.207.1.1.62
OBJECT IDENTIFIER    

at-AR444Router 1.3.6.1.4.1.207.1.1.63
OBJECT IDENTIFIER    

at-AR420Router 1.3.6.1.4.1.207.1.1.64
OBJECT IDENTIFIER    

at-AR550Router 1.3.6.1.4.1.207.1.1.73
OBJECT IDENTIFIER    

at-AR551Router 1.3.6.1.4.1.207.1.1.74
OBJECT IDENTIFIER    

at-AR552Router 1.3.6.1.4.1.207.1.1.75
OBJECT IDENTIFIER    

routerSwitch 1.3.6.1.4.1.207.1.14
OBJECT IDENTIFIER    

at-Rapier24 1.3.6.1.4.1.207.1.14.1
OBJECT IDENTIFIER    

at-Rapier16fSC 1.3.6.1.4.1.207.1.14.2
OBJECT IDENTIFIER    

at-Rapier16fVF 1.3.6.1.4.1.207.1.14.3
OBJECT IDENTIFIER    

at-Rapier16fMT 1.3.6.1.4.1.207.1.14.4
OBJECT IDENTIFIER    

at-Rapier48 1.3.6.1.4.1.207.1.14.5
OBJECT IDENTIFIER    

at-Rapier8t8fSC 1.3.6.1.4.1.207.1.14.6
OBJECT IDENTIFIER    

at-Rapier8t8fSCi 1.3.6.1.4.1.207.1.14.7
OBJECT IDENTIFIER    

at-Rapier8t8fMT 1.3.6.1.4.1.207.1.14.8
OBJECT IDENTIFIER    

at-Rapier8t8fMTi 1.3.6.1.4.1.207.1.14.9
OBJECT IDENTIFIER    

at-Rapier8fSC 1.3.6.1.4.1.207.1.14.10
OBJECT IDENTIFIER    

at-Rapier8fSCi 1.3.6.1.4.1.207.1.14.11
OBJECT IDENTIFIER    

at-Rapier8fMT 1.3.6.1.4.1.207.1.14.12
OBJECT IDENTIFIER    

at-Rapier8fMTi 1.3.6.1.4.1.207.1.14.13
OBJECT IDENTIFIER    

at-Rapier16fMTi 1.3.6.1.4.1.207.1.14.14
OBJECT IDENTIFIER    

at-RapierG6 1.3.6.1.4.1.207.1.14.15
OBJECT IDENTIFIER    

at-RapierG6SX 1.3.6.1.4.1.207.1.14.16
OBJECT IDENTIFIER    

at-RapierG6LX 1.3.6.1.4.1.207.1.14.17
OBJECT IDENTIFIER    

at-RapierG6MT 1.3.6.1.4.1.207.1.14.18
OBJECT IDENTIFIER    

at-Rapier16fSCi 1.3.6.1.4.1.207.1.14.19
OBJECT IDENTIFIER    

at-Rapier24i 1.3.6.1.4.1.207.1.14.20
OBJECT IDENTIFIER    

at-Rapier48i 1.3.6.1.4.1.207.1.14.21
OBJECT IDENTIFIER    

at-Switchblade4AC 1.3.6.1.4.1.207.1.14.22
OBJECT IDENTIFIER    

at-Switchblade4DC 1.3.6.1.4.1.207.1.14.23
OBJECT IDENTIFIER    

at-Switchblade8AC 1.3.6.1.4.1.207.1.14.24
OBJECT IDENTIFIER    

at-Switchblade8DC 1.3.6.1.4.1.207.1.14.25
OBJECT IDENTIFIER    

at-9816GF 1.3.6.1.4.1.207.1.14.26
OBJECT IDENTIFIER    

at-9812TF 1.3.6.1.4.1.207.1.14.27
OBJECT IDENTIFIER    

at-9816GB 1.3.6.1.4.1.207.1.14.28
OBJECT IDENTIFIER    

at-9812T 1.3.6.1.4.1.207.1.14.29
OBJECT IDENTIFIER    

at-8724XL 1.3.6.1.4.1.207.1.14.30
OBJECT IDENTIFIER    

at-8748XL 1.3.6.1.4.1.207.1.14.31
OBJECT IDENTIFIER    

at-8724XLDC 1.3.6.1.4.1.207.1.14.32
OBJECT IDENTIFIER    

at-8748XLDC 1.3.6.1.4.1.207.1.14.33
OBJECT IDENTIFIER    

at-9816GB-DC 1.3.6.1.4.1.207.1.14.34
OBJECT IDENTIFIER    

at-9812T-DC 1.3.6.1.4.1.207.1.14.35
OBJECT IDENTIFIER    

at-8824 1.3.6.1.4.1.207.1.14.36
OBJECT IDENTIFIER    

at-8848 1.3.6.1.4.1.207.1.14.37
OBJECT IDENTIFIER    

at-8824-DC 1.3.6.1.4.1.207.1.14.38
OBJECT IDENTIFIER    

at-8848-DC 1.3.6.1.4.1.207.1.14.39
OBJECT IDENTIFIER    

at-8624XL-80 1.3.6.1.4.1.207.1.14.41
OBJECT IDENTIFIER    

at-8724XL-80 1.3.6.1.4.1.207.1.14.42
OBJECT IDENTIFIER    

at-8748XL-80 1.3.6.1.4.1.207.1.14.43
OBJECT IDENTIFIER    

at-8948EX 1.3.6.1.4.1.207.1.14.44
OBJECT IDENTIFIER    

at-8948MX 1.3.6.1.4.1.207.1.14.45
OBJECT IDENTIFIER    

at-8624T2M 1.3.6.1.4.1.207.1.14.46
OBJECT IDENTIFIER    

at-Rapier24i-DC-NEBS 1.3.6.1.4.1.207.1.14.47
OBJECT IDENTIFIER    

at-8724XL-DC-NEBS 1.3.6.1.4.1.207.1.14.48
OBJECT IDENTIFIER    

at-9924T 1.3.6.1.4.1.207.1.14.49
OBJECT IDENTIFIER    

at-9924SP 1.3.6.1.4.1.207.1.14.50
OBJECT IDENTIFIER    

at-9924T-4SP 1.3.6.1.4.1.207.1.14.51
OBJECT IDENTIFIER    

at-9924TEMC 1.3.6.1.4.1.207.1.14.53
OBJECT IDENTIFIER    

at-8724MLB 1.3.6.1.4.1.207.1.14.55
OBJECT IDENTIFIER    

at-8624POE 1.3.6.1.4.1.207.1.14.56
OBJECT IDENTIFIER    

at-86482SP 1.3.6.1.4.1.207.1.14.58
OBJECT IDENTIFIER    

brouterMib 1.3.6.1.4.1.207.8.4
OBJECT IDENTIFIER    

atRouter 1.3.6.1.4.1.207.8.4.4
OBJECT IDENTIFIER    

objects 1.3.6.1.4.1.207.8.4.4.1
OBJECT IDENTIFIER    

traps 1.3.6.1.4.1.207.8.4.4.2
OBJECT IDENTIFIER    

sysinfo 1.3.6.1.4.1.207.8.4.4.3
OBJECT IDENTIFIER    

modules 1.3.6.1.4.1.207.8.4.4.4
OBJECT IDENTIFIER    

arInterfaces 1.3.6.1.4.1.207.8.4.4.5
OBJECT IDENTIFIER    

protocols 1.3.6.1.4.1.207.8.4.4.6
OBJECT IDENTIFIER    

boards 1.3.6.1.4.1.207.8.4.4.1.1
OBJECT IDENTIFIER    

pprIcmAr023 1.3.6.1.4.1.207.8.4.4.1.1.39
OBJECT IDENTIFIER    

pprIcmAr021s 1.3.6.1.4.1.207.8.4.4.1.1.40
OBJECT IDENTIFIER    

pprIcmAr022 1.3.6.1.4.1.207.8.4.4.1.1.41
OBJECT IDENTIFIER    

pprIcmAr025 1.3.6.1.4.1.207.8.4.4.1.1.45
OBJECT IDENTIFIER    

pprIcmAr024 1.3.6.1.4.1.207.8.4.4.1.1.46
OBJECT IDENTIFIER    

pprAr300 1.3.6.1.4.1.207.8.4.4.1.1.49
OBJECT IDENTIFIER    

pprAr300L 1.3.6.1.4.1.207.8.4.4.1.1.52
OBJECT IDENTIFIER    

pprAr310 1.3.6.1.4.1.207.8.4.4.1.1.53
OBJECT IDENTIFIER    

pprAr120 1.3.6.1.4.1.207.8.4.4.1.1.54
OBJECT IDENTIFIER    

pprAr300Lu 1.3.6.1.4.1.207.8.4.4.1.1.55
OBJECT IDENTIFIER    

pprAr300u 1.3.6.1.4.1.207.8.4.4.1.1.56
OBJECT IDENTIFIER    

pprAr310u 1.3.6.1.4.1.207.8.4.4.1.1.57
OBJECT IDENTIFIER    

pprAr350 1.3.6.1.4.1.207.8.4.4.1.1.58
OBJECT IDENTIFIER    

pprIcmAr021u 1.3.6.1.4.1.207.8.4.4.1.1.59
OBJECT IDENTIFIER    

pprAr720 1.3.6.1.4.1.207.8.4.4.1.1.63
OBJECT IDENTIFIER    

pprAr010 1.3.6.1.4.1.207.8.4.4.1.1.67
OBJECT IDENTIFIER    

pprAr012 1.3.6.1.4.1.207.8.4.4.1.1.68
OBJECT IDENTIFIER    

pprAr011 1.3.6.1.4.1.207.8.4.4.1.1.69
OBJECT IDENTIFIER    

pprAr370 1.3.6.1.4.1.207.8.4.4.1.1.70
OBJECT IDENTIFIER    

pprAr330 1.3.6.1.4.1.207.8.4.4.1.1.71
OBJECT IDENTIFIER    

pprAr395 1.3.6.1.4.1.207.8.4.4.1.1.72
OBJECT IDENTIFIER    

pprAr390 1.3.6.1.4.1.207.8.4.4.1.1.73
OBJECT IDENTIFIER    

pprAr370u 1.3.6.1.4.1.207.8.4.4.1.1.75
OBJECT IDENTIFIER    

pprIcmAr020 1.3.6.1.4.1.207.8.4.4.1.1.76
OBJECT IDENTIFIER    

pprAr740 1.3.6.1.4.1.207.8.4.4.1.1.79
OBJECT IDENTIFIER    

pprAr140s 1.3.6.1.4.1.207.8.4.4.1.1.80
OBJECT IDENTIFIER    

pprAr140u 1.3.6.1.4.1.207.8.4.4.1.1.81
OBJECT IDENTIFIER    

pprAr160su 1.3.6.1.4.1.207.8.4.4.1.1.82
OBJECT IDENTIFIER    

pprAr320 1.3.6.1.4.1.207.8.4.4.1.1.83
OBJECT IDENTIFIER    

pprAr130s 1.3.6.1.4.1.207.8.4.4.1.1.85
OBJECT IDENTIFIER    

pprAr130u 1.3.6.1.4.1.207.8.4.4.1.1.86
OBJECT IDENTIFIER    

pprRapier24 1.3.6.1.4.1.207.8.4.4.1.1.87
OBJECT IDENTIFIER    

pprNsm0404Pic 1.3.6.1.4.1.207.8.4.4.1.1.88
OBJECT IDENTIFIER    

pprA35SXSC 1.3.6.1.4.1.207.8.4.4.1.1.89
OBJECT IDENTIFIER    

pprA35LXSC 1.3.6.1.4.1.207.8.4.4.1.1.90
OBJECT IDENTIFIER    

pprA36MTRJ 1.3.6.1.4.1.207.8.4.4.1.1.91
OBJECT IDENTIFIER    

pprA37VF45 1.3.6.1.4.1.207.8.4.4.1.1.92
OBJECT IDENTIFIER    

pprA38LC 1.3.6.1.4.1.207.8.4.4.1.1.93
OBJECT IDENTIFIER    

pprA39Tx 1.3.6.1.4.1.207.8.4.4.1.1.94
OBJECT IDENTIFIER    

pprAr740DC 1.3.6.1.4.1.207.8.4.4.1.1.95
OBJECT IDENTIFIER    

pprNsm0418BRI 1.3.6.1.4.1.207.8.4.4.1.1.96
OBJECT IDENTIFIER    

pprRapier16fSC 1.3.6.1.4.1.207.8.4.4.1.1.97
OBJECT IDENTIFIER    

ppr8624xl80 1.3.6.1.4.1.207.8.4.4.1.1.98
OBJECT IDENTIFIER    

pprRapier16fMT 1.3.6.1.4.1.207.8.4.4.1.1.99
OBJECT IDENTIFIER    

pprRapier16fMTi 1.3.6.1.4.1.207.8.4.4.1.1.100
OBJECT IDENTIFIER    

pprRapier8t8fSC 1.3.6.1.4.1.207.8.4.4.1.1.101
OBJECT IDENTIFIER    

pprRapier8t8fSCi 1.3.6.1.4.1.207.8.4.4.1.1.102
OBJECT IDENTIFIER    

pprRapier8t8fMT 1.3.6.1.4.1.207.8.4.4.1.1.103
OBJECT IDENTIFIER    

pprRapier8t8fMTi 1.3.6.1.4.1.207.8.4.4.1.1.104
OBJECT IDENTIFIER    

pprRapier8fSC 1.3.6.1.4.1.207.8.4.4.1.1.105
OBJECT IDENTIFIER    

pprRapier8fSCi 1.3.6.1.4.1.207.8.4.4.1.1.106
OBJECT IDENTIFIER    

pprRapier8fMT 1.3.6.1.4.1.207.8.4.4.1.1.107
OBJECT IDENTIFIER    

pprRapier8fMTi 1.3.6.1.4.1.207.8.4.4.1.1.108
OBJECT IDENTIFIER    

pprRapierG6 1.3.6.1.4.1.207.8.4.4.1.1.110
OBJECT IDENTIFIER    

pprRapierG6SX 1.3.6.1.4.1.207.8.4.4.1.1.111
OBJECT IDENTIFIER    

pprRapierG6LX 1.3.6.1.4.1.207.8.4.4.1.1.112
OBJECT IDENTIFIER    

pprRapierG6MT 1.3.6.1.4.1.207.8.4.4.1.1.113
OBJECT IDENTIFIER    

pprRapier16fSCi 1.3.6.1.4.1.207.8.4.4.1.1.114
OBJECT IDENTIFIER    

pprRapier24i 1.3.6.1.4.1.207.8.4.4.1.1.115
OBJECT IDENTIFIER    

pprAr824 1.3.6.1.4.1.207.8.4.4.1.1.116
OBJECT IDENTIFIER    

pprAr816fSC 1.3.6.1.4.1.207.8.4.4.1.1.117
OBJECT IDENTIFIER    

pprAr816fSCi 1.3.6.1.4.1.207.8.4.4.1.1.118
OBJECT IDENTIFIER    

pprAr816fMT 1.3.6.1.4.1.207.8.4.4.1.1.119
OBJECT IDENTIFIER    

pprAr816fMTi 1.3.6.1.4.1.207.8.4.4.1.1.120
OBJECT IDENTIFIER    

pprAr88t8fSC 1.3.6.1.4.1.207.8.4.4.1.1.121
OBJECT IDENTIFIER    

pprAr88t8fSCi 1.3.6.1.4.1.207.8.4.4.1.1.122
OBJECT IDENTIFIER    

pprAr88t8fMT 1.3.6.1.4.1.207.8.4.4.1.1.123
OBJECT IDENTIFIER    

pprAr88t8fMTi 1.3.6.1.4.1.207.8.4.4.1.1.124
OBJECT IDENTIFIER    

pprAr88fSC 1.3.6.1.4.1.207.8.4.4.1.1.125
OBJECT IDENTIFIER    

pprAr88fSCi 1.3.6.1.4.1.207.8.4.4.1.1.126
OBJECT IDENTIFIER    

pprAr88fMT 1.3.6.1.4.1.207.8.4.4.1.1.127
OBJECT IDENTIFIER    

pprAr88fMTi 1.3.6.1.4.1.207.8.4.4.1.1.128
OBJECT IDENTIFIER    

pprAr824i 1.3.6.1.4.1.207.8.4.4.1.1.129
OBJECT IDENTIFIER    

pprAt8724XL 1.3.6.1.4.1.207.8.4.4.1.1.130
OBJECT IDENTIFIER    

pprAt8748XL 1.3.6.1.4.1.207.8.4.4.1.1.131
OBJECT IDENTIFIER    

pprAt8724XLDC 1.3.6.1.4.1.207.8.4.4.1.1.132
OBJECT IDENTIFIER    

pprAt8748XLDC 1.3.6.1.4.1.207.8.4.4.1.1.133
OBJECT IDENTIFIER    

pprAt8824 1.3.6.1.4.1.207.8.4.4.1.1.134
OBJECT IDENTIFIER    

pprAt8824DC 1.3.6.1.4.1.207.8.4.4.1.1.135
OBJECT IDENTIFIER    

ppr8724XLDC 1.3.6.1.4.1.207.8.4.4.1.1.141
OBJECT IDENTIFIER    

ppr8748XLDC 1.3.6.1.4.1.207.8.4.4.1.1.142
OBJECT IDENTIFIER    

pprRapier24iDC-NEBS 1.3.6.1.4.1.207.8.4.4.1.1.144
OBJECT IDENTIFIER    

pprAt8724XLDC-NEBS 1.3.6.1.4.1.207.8.4.4.1.1.146
OBJECT IDENTIFIER    

pprAt8848DC 1.3.6.1.4.1.207.8.4.4.1.1.147
OBJECT IDENTIFIER    

pprRapier48 1.3.6.1.4.1.207.8.4.4.1.1.148
OBJECT IDENTIFIER    

pprAt8848 1.3.6.1.4.1.207.8.4.4.1.1.149
OBJECT IDENTIFIER    

pprRapier48i 1.3.6.1.4.1.207.8.4.4.1.1.150
OBJECT IDENTIFIER    

pprNsm0424BRI 1.3.6.1.4.1.207.8.4.4.1.1.151
OBJECT IDENTIFIER    

pprIcmAR026 1.3.6.1.4.1.207.8.4.4.1.1.153
OBJECT IDENTIFIER    

ppr9816GF 1.3.6.1.4.1.207.8.4.4.1.1.157
OBJECT IDENTIFIER    

ppr9812TF 1.3.6.1.4.1.207.8.4.4.1.1.158
OBJECT IDENTIFIER    

pprSbChassis4AC 1.3.6.1.4.1.207.8.4.4.1.1.159
OBJECT IDENTIFIER    

pprSbChassis4DC 1.3.6.1.4.1.207.8.4.4.1.1.160
OBJECT IDENTIFIER    

pprSbChassis8AC 1.3.6.1.4.1.207.8.4.4.1.1.161
OBJECT IDENTIFIER    

pprSbChassis8DC 1.3.6.1.4.1.207.8.4.4.1.1.162
OBJECT IDENTIFIER    

pprSbChassis16AC 1.3.6.1.4.1.207.8.4.4.1.1.163
OBJECT IDENTIFIER    

pprSbChassis16DC 1.3.6.1.4.1.207.8.4.4.1.1.164
OBJECT IDENTIFIER    

pprSbControl 1.3.6.1.4.1.207.8.4.4.1.1.165
OBJECT IDENTIFIER    

pprSbControlDTM 1.3.6.1.4.1.207.8.4.4.1.1.166
OBJECT IDENTIFIER    

pprSb48t 1.3.6.1.4.1.207.8.4.4.1.1.167
OBJECT IDENTIFIER    

pprSb96t 1.3.6.1.4.1.207.8.4.4.1.1.168
OBJECT IDENTIFIER    

pprSb32fSC 1.3.6.1.4.1.207.8.4.4.1.1.169
OBJECT IDENTIFIER    

pprSb32fMT 1.3.6.1.4.1.207.8.4.4.1.1.170
OBJECT IDENTIFIER    

pprSb8fRJ 1.3.6.1.4.1.207.8.4.4.1.1.172
OBJECT IDENTIFIER    

pprSb8fSXSC 1.3.6.1.4.1.207.8.4.4.1.1.173
OBJECT IDENTIFIER    

pprSb8fSXMT 1.3.6.1.4.1.207.8.4.4.1.1.174
OBJECT IDENTIFIER    

pprSb8fLXSC 1.3.6.1.4.1.207.8.4.4.1.1.175
OBJECT IDENTIFIER    

pprSb8fLXMT 1.3.6.1.4.1.207.8.4.4.1.1.176
OBJECT IDENTIFIER    

pprAr410 1.3.6.1.4.1.207.8.4.4.1.1.177
OBJECT IDENTIFIER    

pprA40SC 1.3.6.1.4.1.207.8.4.4.1.1.178
OBJECT IDENTIFIER    

pprA40MTRJ 1.3.6.1.4.1.207.8.4.4.1.1.179
OBJECT IDENTIFIER    

pprA41SC 1.3.6.1.4.1.207.8.4.4.1.1.180
OBJECT IDENTIFIER    

pprA41MTRJ 1.3.6.1.4.1.207.8.4.4.1.1.181
OBJECT IDENTIFIER    

pprAr725 1.3.6.1.4.1.207.8.4.4.1.1.182
OBJECT IDENTIFIER    

pprAr745 1.3.6.1.4.1.207.8.4.4.1.1.183
OBJECT IDENTIFIER    

pprSb8GBIC 1.3.6.1.4.1.207.8.4.4.1.1.184
OBJECT IDENTIFIER    

pprA42GBIC 1.3.6.1.4.1.207.8.4.4.1.1.185
OBJECT IDENTIFIER    

ppr9816GB 1.3.6.1.4.1.207.8.4.4.1.1.186
OBJECT IDENTIFIER    

ppr9812T 1.3.6.1.4.1.207.8.4.4.1.1.187
OBJECT IDENTIFIER    

pprNsm048DS3 1.3.6.1.4.1.207.8.4.4.1.1.188
OBJECT IDENTIFIER    

pprAr450 1.3.6.1.4.1.207.8.4.4.1.1.191
OBJECT IDENTIFIER    

pprAr450Dual 1.3.6.1.4.1.207.8.4.4.1.1.192
OBJECT IDENTIFIER    

pprSbExpander 1.3.6.1.4.1.207.8.4.4.1.1.193
OBJECT IDENTIFIER    

pprAr725DC 1.3.6.1.4.1.207.8.4.4.1.1.194
OBJECT IDENTIFIER    

pprAr745DC 1.3.6.1.4.1.207.8.4.4.1.1.195
OBJECT IDENTIFIER    

pprAr410v2 1.3.6.1.4.1.207.8.4.4.1.1.196
OBJECT IDENTIFIER    

pprAr410v3 1.3.6.1.4.1.207.8.4.4.1.1.197
OBJECT IDENTIFIER    

pprIcmAr027 1.3.6.1.4.1.207.8.4.4.1.1.198
OBJECT IDENTIFIER    

ppr8948EX 1.3.6.1.4.1.207.8.4.4.1.1.202
OBJECT IDENTIFIER    

ppr8948MX 1.3.6.1.4.1.207.8.4.4.1.1.203
OBJECT IDENTIFIER    

ppr9816GBDC 1.3.6.1.4.1.207.8.4.4.1.1.204
OBJECT IDENTIFIER    

ppr9812TDC 1.3.6.1.4.1.207.8.4.4.1.1.205
OBJECT IDENTIFIER    

pprIcmAr021v2s 1.3.6.1.4.1.207.8.4.4.1.1.206
OBJECT IDENTIFIER    

pprA50 1.3.6.1.4.1.207.8.4.4.1.1.207
OBJECT IDENTIFIER    

pprA51 1.3.6.1.4.1.207.8.4.4.1.1.208
OBJECT IDENTIFIER    

pprA52 1.3.6.1.4.1.207.8.4.4.1.1.209
OBJECT IDENTIFIER    

pprA53 1.3.6.1.4.1.207.8.4.4.1.1.210
OBJECT IDENTIFIER    

pprFanA01 1.3.6.1.4.1.207.8.4.4.1.1.212
OBJECT IDENTIFIER    

pprAtPwr01AC 1.3.6.1.4.1.207.8.4.4.1.1.213
OBJECT IDENTIFIER    

pprAtPwr01DC 1.3.6.1.4.1.207.8.4.4.1.1.214
OBJECT IDENTIFIER    

pprAtFan01 1.3.6.1.4.1.207.8.4.4.1.1.215
OBJECT IDENTIFIER    

pprSb24RJ 1.3.6.1.4.1.207.8.4.4.1.1.216
OBJECT IDENTIFIER    

pprSb1XFP 1.3.6.1.4.1.207.8.4.4.1.1.217
OBJECT IDENTIFIER    

ppr9924T 1.3.6.1.4.1.207.8.4.4.1.1.218
OBJECT IDENTIFIER    

ppr9924SP 1.3.6.1.4.1.207.8.4.4.1.1.219
OBJECT IDENTIFIER    

ppr9924TEMC 1.3.6.1.4.1.207.8.4.4.1.1.220
OBJECT IDENTIFIER    

ppr9924T4SP 1.3.6.1.4.1.207.8.4.4.1.1.221
OBJECT IDENTIFIER    

pprAR440 1.3.6.1.4.1.207.8.4.4.1.1.227
OBJECT IDENTIFIER    

pprAR441 1.3.6.1.4.1.207.8.4.4.1.1.228
OBJECT IDENTIFIER    

pprAR442 1.3.6.1.4.1.207.8.4.4.1.1.229
OBJECT IDENTIFIER    

pprAR443 1.3.6.1.4.1.207.8.4.4.1.1.230
OBJECT IDENTIFIER    

pprAR444 1.3.6.1.4.1.207.8.4.4.1.1.231
OBJECT IDENTIFIER    

pprAR420 1.3.6.1.4.1.207.8.4.4.1.1.232
OBJECT IDENTIFIER    

pprAt8624T2M 1.3.6.1.4.1.207.8.4.4.1.1.239
OBJECT IDENTIFIER    

pprA46Tx 1.3.6.1.4.1.207.8.4.4.1.1.240
OBJECT IDENTIFIER    

pprAR550 1.3.6.1.4.1.207.8.4.4.1.1.241
OBJECT IDENTIFIER    

pprAR551 1.3.6.1.4.1.207.8.4.4.1.1.242
OBJECT IDENTIFIER    

pprAR552 1.3.6.1.4.1.207.8.4.4.1.1.243
OBJECT IDENTIFIER    

pprC8724MLB 1.3.6.1.4.1.207.8.4.4.1.1.248
OBJECT IDENTIFIER    

pprAt86482SP 1.3.6.1.4.1.207.8.4.4.1.1.252
OBJECT IDENTIFIER    

pprAt8624POE 1.3.6.1.4.1.207.8.4.4.1.1.253
OBJECT IDENTIFIER    

pprAtPwr01RAC 1.3.6.1.4.1.207.8.4.4.1.1.254
OBJECT IDENTIFIER    

pprAtFan01R 1.3.6.1.4.1.207.8.4.4.1.1.255
OBJECT IDENTIFIER    

pprAtPwr02AC 1.3.6.1.4.1.207.8.4.4.1.1.264
OBJECT IDENTIFIER    

pprAtPwr02RAC 1.3.6.1.4.1.207.8.4.4.1.1.265
OBJECT IDENTIFIER    

pprSb24SFP 1.3.6.1.4.1.207.8.4.4.1.1.269
OBJECT IDENTIFIER    

release 1.3.6.1.4.1.207.8.4.4.1.2
OBJECT IDENTIFIER    

iftypes 1.3.6.1.4.1.207.8.4.4.1.3
OBJECT IDENTIFIER    

ifaceEth 1.3.6.1.4.1.207.8.4.4.1.3.1
OBJECT IDENTIFIER    

ifaceSyn 1.3.6.1.4.1.207.8.4.4.1.3.2
OBJECT IDENTIFIER    

ifaceAsyn 1.3.6.1.4.1.207.8.4.4.1.3.3
OBJECT IDENTIFIER    

ifaceBri 1.3.6.1.4.1.207.8.4.4.1.3.4
OBJECT IDENTIFIER    

ifacePri 1.3.6.1.4.1.207.8.4.4.1.3.5
OBJECT IDENTIFIER    

ifacePots 1.3.6.1.4.1.207.8.4.4.1.3.6
OBJECT IDENTIFIER    

ifaceGBIC 1.3.6.1.4.1.207.8.4.4.1.3.7
OBJECT IDENTIFIER    

chips 1.3.6.1.4.1.207.8.4.4.1.4
OBJECT IDENTIFIER    

chip68020Cpu 1.3.6.1.4.1.207.8.4.4.1.4.1
OBJECT IDENTIFIER    

chip68340Cpu 1.3.6.1.4.1.207.8.4.4.1.4.2
OBJECT IDENTIFIER    

chip68302Cpu 1.3.6.1.4.1.207.8.4.4.1.4.3
OBJECT IDENTIFIER    

chip68360Cpu 1.3.6.1.4.1.207.8.4.4.1.4.4
OBJECT IDENTIFIER    

chip860TCpu 1.3.6.1.4.1.207.8.4.4.1.4.5
OBJECT IDENTIFIER    

chipRtc1 1.3.6.1.4.1.207.8.4.4.1.4.21
OBJECT IDENTIFIER    

chipRtc2 1.3.6.1.4.1.207.8.4.4.1.4.22
OBJECT IDENTIFIER    

chipRtc3 1.3.6.1.4.1.207.8.4.4.1.4.23
OBJECT IDENTIFIER    

chipRtc4 1.3.6.1.4.1.207.8.4.4.1.4.24
OBJECT IDENTIFIER    

chipRam1mb 1.3.6.1.4.1.207.8.4.4.1.4.31
OBJECT IDENTIFIER    

chipRam2mb 1.3.6.1.4.1.207.8.4.4.1.4.32
OBJECT IDENTIFIER    

chipRam3mb 1.3.6.1.4.1.207.8.4.4.1.4.33
OBJECT IDENTIFIER    

chipRam4mb 1.3.6.1.4.1.207.8.4.4.1.4.34
OBJECT IDENTIFIER    

chipRam6mb 1.3.6.1.4.1.207.8.4.4.1.4.36
OBJECT IDENTIFIER    

chipRam8mb 1.3.6.1.4.1.207.8.4.4.1.4.38
OBJECT IDENTIFIER    

chipRam12mb 1.3.6.1.4.1.207.8.4.4.1.4.42
OBJECT IDENTIFIER    

chipRam16mb 1.3.6.1.4.1.207.8.4.4.1.4.46
OBJECT IDENTIFIER    

chipRam20mb 1.3.6.1.4.1.207.8.4.4.1.4.50
OBJECT IDENTIFIER    

chipRam32mb 1.3.6.1.4.1.207.8.4.4.1.4.62
OBJECT IDENTIFIER    

chipFlash1mb 1.3.6.1.4.1.207.8.4.4.1.4.71
OBJECT IDENTIFIER    

chipFlash2mb 1.3.6.1.4.1.207.8.4.4.1.4.72
OBJECT IDENTIFIER    

chipFlash3mb 1.3.6.1.4.1.207.8.4.4.1.4.73
OBJECT IDENTIFIER    

chipFlash4mb 1.3.6.1.4.1.207.8.4.4.1.4.74
OBJECT IDENTIFIER    

chipFlash6mb 1.3.6.1.4.1.207.8.4.4.1.4.76
OBJECT IDENTIFIER    

chipFlash8mb 1.3.6.1.4.1.207.8.4.4.1.4.78
OBJECT IDENTIFIER    

chipPem 1.3.6.1.4.1.207.8.4.4.1.4.120
OBJECT IDENTIFIER    

fanAndPs 1.3.6.1.4.1.207.8.4.4.3.1
OBJECT IDENTIFIER    

fanAndPsRpsConnectionStatus 1.3.6.1.4.1.207.8.4.4.3.1.1
The status of the Redundant Power Supply (RPS) connection, ie, whether an RPS is actually connected or not, regardless of whether the RPS is on or not. not-supported means that an RPS is not supported in this hardware platform, connected means that the RPS is connected, not-connected means that the RPS is not connected, and not-monitoring means that the status of the RPS is not being monitored presently. RPS monitoring can be turned on via the variable fanAndPsRpsMonitoringStatus, or by the command SET SYSTEM RPSMONITOR=ON.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER non-supported(0), connected(1), not-connected(2), not-monitoring(3)  

fanAndPsMainPSUStatus 1.3.6.1.4.1.207.8.4.4.3.1.2
The status of the main Power Supply. on means that the power supply is present and fully operational. off means that the power supply is totally off (and obviously only applies to systems with a redundant power supply). faulty means that the main power supply is delivering power but that a component of the power supply is faulty. This applies to systems like SwitchBlade which have 3 power supplies but do not provide individual power supply monitoring. Also, in the case of SwitchBlade, power supply status includes the status of the fans in the power supply.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), faulty(3)  

fanAndPsRedundantPSUStatus 1.3.6.1.4.1.207.8.4.4.3.1.3
The status of the redundant Power Supply. non-supported means this device does not support redundant power supplies, on means that the redundant power supply is connected and able to supply system power if required, off means that the redundant power supply is either not connected or is connected and is not able to supply system power if required, and not-monitoring means that the status of the RPS is not being monitored presently. RPS monitoring can be turned on via the variable fanAndPsRpsMonitoringStatus, or by the command SET SYSTEM RPSMONITOR=ON.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER non-supported(0), on(1), off(2), not-monitoring(3)  

fanAndPsRpsMonitoringStatus 1.3.6.1.4.1.207.8.4.4.3.1.4
The current status of redundant power supply monitoring. The monitoring of the redundant power supply and its fan must be enabled by command or by setting this variable to on. The value non-supported means that this device does not support redundant power supplies. Only the values on or off may be written to this variable. If this variables reads as non-supported, an attempt to write to this variable will result in a bad value error.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER non-supported(0), on(1), off(2)  

fanAndPsMainFanStatus 1.3.6.1.4.1.207.8.4.4.3.1.5
The status of the main Power Supply fan. non-supported means that this device does not support monitoring on the main power supply fan, or that there is no main power supply fan. The warning means the fan's speed is outside 30% of the expected speed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER non-supported(0), ok(1), not-ok(2), warning(3)  

fanAndPsRedundantFanStatus 1.3.6.1.4.1.207.8.4.4.3.1.6
The status of the redundant Power Supply Fan. non-supported means this device does not support redundant power supplies, ok means that the redundant power supply fan is running, not-ok means that the redundant power supply fan is not running, and not-monitoring means that the status of the RPS is not being monitored presently. RPS monitoring can be turned on via the variable fanAndPsRpsMonitoringStatus, or by the command SET SYSTEM RPSMONITOR=ON.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER non-supported(0), ok(1), not-ok(2), not-monitoring(3)  

fanAndPsTemperatureStatus 1.3.6.1.4.1.207.8.4.4.3.1.7
The status of temperature in this device. ok means that the device is not capable of monitoring temperature or that the temperature is OK, not-ok means that the temperature is being monitored and is currently out of the range 0C - 45C.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), not-ok(2)  

fanAndPsFanTrayPresent 1.3.6.1.4.1.207.8.4.4.3.1.8
The status of the presence of the fan tray in this system. Systems which do not support a fan tray return the value non-supported. Upon removal of the fan tray there is a short period (20s) before the value of this variable is changed to not-present. This is to allow for scheduled replacement and/or cleaning of the fan tray.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER non-supported(0), present(1), not-present(2)  

fanAndPsFanTrayStatus 1.3.6.1.4.1.207.8.4.4.3.1.9
The status of the fan tray in this system. Systems which do not support a fan tray return the value non-supported. The value ok is returned if all fans in the fan tray are running at full speed. The value not-ok is returned if one of more of the fan tray fans is running slow or has stalled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER non-supported(0), ok(1), not-ok(2)  

fanAndPsMainMonitoringStatus 1.3.6.1.4.1.207.8.4.4.3.1.10
The current status of main power supply monitoring. The monitoring of the main power supply and its fan is always enabled by those systems that support it. Systems which do not support main power supply or fan monitoring report a value of not-supported. The value ok is returned for those systems that do support main power supply and fan monitoring, and where the monitoring operation is reporting valid information (refer to fanAndPsMainFanStatus for the current status of the system). When main power supply and fan monitoring is failing, the value not-ok is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER non-supported(0), ok(1), not-ok(2)  

fanAndPsPsuStatusTable 1.3.6.1.4.1.207.8.4.4.3.1.11
The table of AT8948 fanAndPsPsuStatusTable. Each entry in the table represents the status of one of the power supplies in AT8948 system. Each power supply has its own board ID.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FanAndPsPsuStatusEntry

fanAndPsPsuStatusEntry 1.3.6.1.4.1.207.8.4.4.3.1.11.1
A single entry of AT8948 fanAndPsPsuStatusTable, indexed by fanAndPsPsuNumber field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FanAndPsPsuStatusEntry  

fanAndPsPsuNumber 1.3.6.1.4.1.207.8.4.4.3.1.11.1.1
The PSU board identity for which this entry holds. If the system consists only of a single PSU board, only one entry will appear in the table, whose index is 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fanAndPsPsuPresent 1.3.6.1.4.1.207.8.4.4.3.1.11.1.2
The PSU present state, displayed as 'yes' if present, or 'no' if absent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(0), no(1)  

fanAndPsPsuType 1.3.6.1.4.1.207.8.4.4.3.1.11.1.3
The PSU type, displayed as AC, or DC, or FAN, or NOT PRESENT.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ac(0), dc(1), fan(2), not-present(3), not-supported(4)  

fanAndPsPsuFan 1.3.6.1.4.1.207.8.4.4.3.1.11.1.4
The PSU fan status, displayed as OK, or FAIL, or NOT PRESENT.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), fail(1), not-present(2), not-supported(3)  

fanAndPsPsuTemperature 1.3.6.1.4.1.207.8.4.4.3.1.11.1.5
The PSU temperature, displayed as GOOD, or HIGH, or NOT PRESENT, or NOT SUPPORTED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER good(0), high(1), not-present(2), not-supported(3)  

fanAndPsPsuPower 1.3.6.1.4.1.207.8.4.4.3.1.11.1.6
The PSU power status, displayed as GOOD, or BAD, or NOT PRESENT or NOT SUPPORTED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER good(0), bad(1), not-present(2), not-supported(3)  

fanAndPsAccelFanStatus 1.3.6.1.4.1.207.8.4.4.3.1.12
The status of the accelerator card fans. Non-supported means this device does not support monitoring of the accelerator card fans.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER non-supported(0), ok(1), not-ok(2)  

fanAndPsRpsConnectionTrap 1
Generated when the RPS connection status changes.
TRAP-TYPE    

fanAndPsMainPSUStatusTrap 2
Generated when the main power supply status changes.
TRAP-TYPE    

fanAndPsRedundantPSUStatusTrap 3
Generated when the RPS status changes.
TRAP-TYPE    

fanAndPsMainFanStatusTrap 4
Generated when the main fan changes status.
TRAP-TYPE    

fanAndPsRedundantFanStatusTrap 5
Generated when the redundant fan changes status.
TRAP-TYPE    

fanAndPsTemperatureStatusTrap 6
Generated when the temperature changes status.
TRAP-TYPE    

fanAndPsFanTrayPresentTrap 7
Generated when the fan tray presence status changes.
TRAP-TYPE    

fanAndPsFanTrayStatusTrap 8
Generated when the fan tray status changes.
TRAP-TYPE    

fanAndPsMainMonitoringStatusTrap 9
Generated when the main power supply monitoring status changes.
TRAP-TYPE    

fanAndPsAccelFanStatusTrap 10
Generated when the accelerator fans' status changes.
TRAP-TYPE    

restart 1.3.6.1.4.1.207.8.4.4.3.2
A router/switch restart request. A management station can remotely instruct an ATI router/switch to action a warm or cold restart. Once all the appropriate internal checks have been made, the router/switch will acknowledge the request via normal SNMP channels. The restart instruction will be actioned after waiting for a period of 5 seconds, this is because the SNMP acknowledgement packet needs time to reach the management station. Once the request has been actioned, it can not be cancelled and communication with the router/switch will be lost during system initialisation.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER restart-none(0), restart-warm(1), restart-cold(2)  

cpu 1.3.6.1.4.1.207.8.4.4.3.3
OBJECT IDENTIFIER    

cpuUtilisationMax 1.3.6.1.4.1.207.8.4.4.3.3.1
Maximum CPU utilisation since the router was last restarted. Expressed as a percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

cpuUtilisationAvg 1.3.6.1.4.1.207.8.4.4.3.3.2
Average CPU utilisation since the router was last restarted. Expressed as a percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

cpuUtilisationAvgLastMinute 1.3.6.1.4.1.207.8.4.4.3.3.3
Average CPU utilisation over the past minute. Expressed as a percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

cpuUtilisationAvgLast10Seconds 1.3.6.1.4.1.207.8.4.4.3.3.4
Average CPU utilisation over the past ten seconds. Expressed as a percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

cpuUtilisationAvgLastSecond 1.3.6.1.4.1.207.8.4.4.3.3.5
Average CPU utilisation over the past second. Expressed as a percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

cpuUtilisationMaxLast5Minutes 1.3.6.1.4.1.207.8.4.4.3.3.6
Maximum CPU utilisation over the last 5 minutes. Expressed as a percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

cpuUtilisationAvgLast5Minutes 1.3.6.1.4.1.207.8.4.4.3.3.7
Average CPU utilisation over the past 5 minutes. Expressed as a percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

sysTemperature 1.3.6.1.4.1.207.8.4.4.3.4
OBJECT IDENTIFIER    

generalTemperature 1.3.6.1.4.1.207.8.4.4.3.4.1
OBJECT IDENTIFIER    

generalTemperatureSupported 1.3.6.1.4.1.207.8.4.4.3.4.1.1
The value supported indicates general temperature is displayed by the device. The value not-supported indicates the device displays specific temperature information or none at all.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-supported(0), supported(1)  

generalTemperatureActualTemp 1.3.6.1.4.1.207.8.4.4.3.4.1.2
The current temperature of product's base board, in degrees Celsius. A device which doesn't support this group will return the value 0 for this variable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

generalTemperatureStatus 1.3.6.1.4.1.207.8.4.4.3.4.1.3
The status of temperature in this device. ok indicates the temperature is below the threshold temperature or the device is not capable of monitoring temperature. not-ok indicates the temperature is being monitored and is currently above the threshold temperature (displayed in generalTemperatureThreshold).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), not-ok(2)  

generalTemperatureThreshold 1.3.6.1.4.1.207.8.4.4.3.4.1.4
The temperature threshold for the device. If the temperature of the device rises above this threshold generalTemeratureStatus will indicate a not-ok status.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

generalTemperatureStatusTrap 1
Generated when the temperature status of the device changes.
TRAP-TYPE    

sbTemperature 1.3.6.1.4.1.207.8.4.4.3.4.2
OBJECT IDENTIFIER    

sbTempTable 1.3.6.1.4.1.207.8.4.4.3.4.2.1
The table of SwitchBlade sysTemperature. Each entry in the table represents temperature monitoring from one of the CPU cards which may be present in the SwitchBlade system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SbTempEntry

sbTempEntry 1.3.6.1.4.1.207.8.4.4.3.4.2.1.1
A single entry of SwitchBlade sysTemperature
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SbTempEntry  

sbTempIndex 1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.1
The board for which this temperature entry holds. If the system consists only of a single CPU board, only one entry will appear in the table, whose index is master(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER master(1), slave(2)  

sbTempActualTemperature 1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.2
The actual SwitchBlade temperature. This temperature is measured within the SwitchBlade CPU, and is sampled at 1 second intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sbTempFixedThresholdStatus 1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.3
The temperature status with regard to the fixed temperature threshold. The value of the fixed temperature threshold is set at 90 degrees C. This variable represents whether the actual temperature is above the threshold (value is crossover(2)) or below the threshold (value is normal(1)). If the temperature is exactly the same as the fixed temperature threshold, the value of this variable reads as normal(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), crossover(2)  

sbTempSettableThresholdStatus 1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.4
The temperature status with regard to the settable temperature threshold. The value of the settable temperature threshold is set by management intervention. This variable represents whether the actual temperature is above the threshold (value is crossover(2)) or below the threshold (value is normal(1)). When the value of this variable is undefined(3), no settable threshold has been specified and the value of sbTempSettableThreshold is not used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), crossover(2), undefined(3)  

sbTempSettableThreshold 1.3.6.1.4.1.207.8.4.4.3.4.2.1.1.5
The value of the settable temperature threshold. This can be set independently for each temperature entry. The value of this threshold is only valid when sbTempSettableThresholdStatus is not set to undefined(3).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 30..100  

sbTempFixedThreshold 1.3.6.1.4.1.207.8.4.4.3.4.2.2
The value of the fixed temperature threshold. This value is fixed for both CPU cards, and cannot be set.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sbTempFixedThresholdTrap 1
Trap occurs when fixed threshold status changes. The actual temperature and the fixed threshold are also given.
TRAP-TYPE    

sbTempSettableThresholdTrap 2
Trap occurs when settable threshold status changes. The actual temperature and the settable threshold are also given.
TRAP-TYPE    

atContactDetails 1.3.6.1.4.1.207.8.4.4.3.5
The contact details for Allied Telesyn inc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

acceleratorTemperature 1.3.6.1.4.1.207.8.4.4.3.4.3
OBJECT IDENTIFIER    

acceleratorTemperatureSupported 1.3.6.1.4.1.207.8.4.4.3.4.3.1
The value supported indicates whether accelerator card temperature is displayed by the device. The value not-supported indicates the device does not display specific accelerator card temperature information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-supported(0), supported(1)  

acceleratorTemperatureActualTemp 1.3.6.1.4.1.207.8.4.4.3.4.3.2
The current temperature of product's base board, in degrees Celsius. A device which doesn't support this group will return the value 0 for this variable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

acceleratorTemperatureStatus 1.3.6.1.4.1.207.8.4.4.3.4.3.3
The status of temperature in this device. ok indicates the temperature is below the threshold temperature or the device is not capable of monitoring temperature. not-ok indicates the temperature is being monitored and is currently above the threshold temperature (displayed in generalTemperatureThreshold).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), not-ok(2)  

acceleratorTemperatureThreshold 1.3.6.1.4.1.207.8.4.4.3.4.3.4
The temperature threshold for the device. If the temperature of the device rises above this threshold generalTemeratureStatus will indicate a not-ok status.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

acceleratorTemperatureStatusTrap 1
Generated when the temperature status of the device changes.
TRAP-TYPE    

bbrNvs 1.3.6.1.4.1.207.8.4.4.3.6
OBJECT IDENTIFIER    

bbrNvsReinitialiseTrap 1
Generated at boot when the device detects that the BBR has been corrupted and reinitialised. This can happen if the device's BBR battery has run down, and the device has been powered off, then on.
TRAP-TYPE    

memory 1.3.6.1.4.1.207.8.4.4.3.7
OBJECT IDENTIFIER    

freeMemory 1.3.6.1.4.1.207.8.4.4.3.7.1
Percentage of free memory still available on device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

totalBuffers 1.3.6.1.4.1.207.8.4.4.3.7.2
Total number of buffers available on device
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

realTimeClockStatus 1.3.6.1.4.1.207.8.4.4.3.8
Shows the status of the real time clock
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(0), normal(1)  

hostId 1.3.6.1.4.1.207.8.4.4.3.9
Host Identifier of this device
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

arBoardMaxIndex 1.3.6.1.4.1.207.8.4.4.5.1
The maximum index of boards in the board table. Index 1 is reserved for the main system board of the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arBoardTable 1.3.6.1.4.1.207.8.4.4.5.2
The table of boards in the AR router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ArBoardEntry

arBoardEntry 1.3.6.1.4.1.207.8.4.4.5.2.1
A single entry in the board table. Each entry consists of information about one board in the router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ArBoardEntry  

arBoardIndex 1.3.6.1.4.1.207.8.4.4.5.2.1.1
The index of the board in the board table. Index 1 is reserved for the main system board of the router. Other boards will take index numbers as they are initialised at router startup, or for routers with hot-swap capability, as boards are added to and removed from the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arBoardId 1.3.6.1.4.1.207.8.4.4.5.2.1.2
The type of board in this board entry. The values of this object are taken from the pprXxx object IDs under the boards sub-tree.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

arBoardName 1.3.6.1.4.1.207.8.4.4.5.2.1.3
The name of the board in this board entry. This is a readable string which identifies the board to the manager.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

arBoardRevision 1.3.6.1.4.1.207.8.4.4.5.2.1.4
The manufacturing revision of the board in this board entry. This string has the format Xm-n, where X is P for prototype, or M for manufacturing, m is the major revision number for this board, and n is the field upgrade revision number for this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

arBoardSerialNumber 1.3.6.1.4.1.207.8.4.4.5.2.1.5
The serial number of the board in this board entry. Serial numbers are strings of decimal numbers up to 10 digits in length. Each and every serial number is globally unique. It is possible for the serial number of a board to be invalid. In this case the value returned for this object will be '*** Invalid ***'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

arBoardTotalSlots 1.3.6.1.4.1.207.8.4.4.5.2.1.6
The number of slots on this board. Each slot from 1 to the value of this object may be empty or occupied by another board. By searching the arSlotTable with this board's board index and all values of slot index from 1 to the value of this object, a tree of the boards in this router can be built. The value 0 for this object means that it has no slots.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arBoardTotalPositions 1.3.6.1.4.1.207.8.4.4.5.2.1.7
The number of positions on this board. Each position from 1 to the value of this object contains a single router interface. Note that positions are different from slots. An position contains an actual interface while a slot contains a different board which itself may contain interfaces in its positions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arSlotTable 1.3.6.1.4.1.207.8.4.4.5.3
The table of slots in the router, indexed by board index and slot index.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ArSlotEntry

arSlotEntry 1.3.6.1.4.1.207.8.4.4.5.3.1
A single entry in the board slot table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ArSlotEntry  

arSlotBoardIndex 1.3.6.1.4.1.207.8.4.4.5.3.1.1
The index of the board for this slot entry. Index 1 is reserved for the main system board of the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arSlotSlotIndex 1.3.6.1.4.1.207.8.4.4.5.3.1.2
The index of the slot for this slot entry. Indices start from 1 and are specific to each different board type. There are no gaps in the sequence of slot indices. The maximum value for slot index is given by the value of arBoardTotalSlots for this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arSlotHeldBoardIndex 1.3.6.1.4.1.207.8.4.4.5.3.1.3
The index of the board held in the slot for this slot entry. This is an index into the arBoardTable. A value of 0 for this object means that the slot is not populated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arSlotDescription 1.3.6.1.4.1.207.8.4.4.5.3.1.4
A description for this slot entry. This is a textual description which gives the manager a clue as to what the slot for this entry is. For example, the slots on an AR 720 have descriptions 'Bay0', 'Bay1' and 'MAC'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

arInterfaceTable 1.3.6.1.4.1.207.8.4.4.5.4
The table of physical interfaces in the AR router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ArInterfaceEntry

arInterfaceEntry 1.3.6.1.4.1.207.8.4.4.5.4.1
A single entry in the interface table. Each entry consists of information about one interface in the router, and is indexed by the board index and the position of the interface on the board.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ArInterfaceEntry  

arInterfaceBoardIndex 1.3.6.1.4.1.207.8.4.4.5.4.1.1
The index of the board in the board table which contains this interface. Index 1 is reserved for the main system board of the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arInterfacePosition 1.3.6.1.4.1.207.8.4.4.5.4.1.2
The position of the interface on the board. Each board type will have well-known positions which are the interfaces provided by the board. The number of positions on a given board is given by the object arBoardTotalPositions for this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arInterfaceIfIndex 1.3.6.1.4.1.207.8.4.4.5.4.1.3
The ifIndex for the interface represented by this entry of the interfaces table. This is the ifIndex of the ifEntry used to represent the physical interface. The value 0 is used for interfaces which don't have an ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

arInterfaceName 1.3.6.1.4.1.207.8.4.4.5.4.1.4
The name of this interface. This is the name that the manager can use to refer to this interface in entering router commands.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

arInterfaceFullName 1.3.6.1.4.1.207.8.4.4.5.4.1.5
The fully qualified name for this interface. This identifies the path that must be followed to reach the interface. This name can be used in router commands. In routers don't support fully qualified names, this is the same as arInterfaceName.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

arIfXTable 1.3.6.1.4.1.207.8.4.4.5.5
The table of interface statistics for the AR router. This table extends the ifTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ArIfXEntry

arIfXEntry 1.3.6.1.4.1.207.8.4.4.5.5.1
A single entry in the interface extension table. Each entry consists of extra interface information not covered in standard MIBs. The index for this table is ifIndex, the same as for ifTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ArIfXEntry  

arIfXIndex 1.3.6.1.4.1.207.8.4.4.5.5.1.1
The index of the ifTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arIfXAverageInputBitsSecond 1.3.6.1.4.1.207.8.4.4.5.5.1.2
The average number of bits received per second on all interfaces over the past 8.5 minutes. The average is calculated by an 8.5 minute (512s) decaying average, which is updated every 4 seconds using the following formula: X' = 127/128X + 1/128i where X' is the new average X is the old average i is the most recent poll result The times and multiplier factors have been chosen to give the simplest possible calculation using bit shifting operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arIfXAverageInputPacketsSecond 1.3.6.1.4.1.207.8.4.4.5.5.1.3
The average number of packets received per second on all interfaces over the past 8.5 minutes. See the description for arIfXAverageInputBitsSecond for details of the way in which the average is calculated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arIfXAverageOutputBitsSecond 1.3.6.1.4.1.207.8.4.4.5.5.1.4
The average number of bits sent per second on all interfaces over the past 8.5 minutes. See the description for arIfXAverageInputBitsSecond for details of the way in which the average is calculated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

arIfXAverageOutputPacketsSecond 1.3.6.1.4.1.207.8.4.4.5.5.1.5
The average number of bits sent per second on all interfaces over the past 8.5 minutes. See the description for arIfXAverageInputBitsSecond for details of the way in which the average is calculated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ethernet 1.3.6.1.4.1.207.8.4.4.4.23
OBJECT IDENTIFIER    

ethIntTable 1.3.6.1.4.1.207.8.4.4.4.23.1
The table of Ethernet interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EthIntEntry

ethIntEntry 1.3.6.1.4.1.207.8.4.4.4.23.1.1
A single entry in the Ethernet interfaces table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EthIntEntry  

ethIntIndex 1.3.6.1.4.1.207.8.4.4.4.23.1.1.1
The ifIndex of the Ethernet interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ethIntBoardIndex 1.3.6.1.4.1.207.8.4.4.4.23.1.1.2
The index in the arBoardTable of the board on which this Ethernet interface resides. If this Ethernet interface is not found, the value of this object is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ethIntBoardPosition 1.3.6.1.4.1.207.8.4.4.4.23.1.1.3
The position on this Ethernet interface's board of this Ethernet interface. If this Ethernet interface is not found, the value of this object is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ethIntDuplexMode 1.3.6.1.4.1.207.8.4.4.4.23.1.1.4
The duplex mode of this Ethernet interface. The value unknown is returned when the interface cannot or has not yet made a determination of its duplex mode, or when the interface cannot be found.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER full-duplex(1), half-duplex(2), unknown(3)  

flash 1.3.6.1.4.1.207.8.4.4.4.31
OBJECT IDENTIFIER    

flashGetFailure 1.3.6.1.4.1.207.8.4.4.4.31.1
The number of flash get operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashOpenFailure 1.3.6.1.4.1.207.8.4.4.4.31.2
The number of flash open operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashReadFailure 1.3.6.1.4.1.207.8.4.4.4.31.3
The number of flash read operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashCloseFailure 1.3.6.1.4.1.207.8.4.4.4.31.4
The number of flash close operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashCompleteFailure 1.3.6.1.4.1.207.8.4.4.4.31.5
The number of flash complete operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashWriteFailure 1.3.6.1.4.1.207.8.4.4.4.31.6
The number of flash write operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashCreateFailure 1.3.6.1.4.1.207.8.4.4.4.31.7
The number of flash create operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashPutFailure 1.3.6.1.4.1.207.8.4.4.4.31.8
The number of flash put operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashDeleteFailure 1.3.6.1.4.1.207.8.4.4.4.31.9
The number of flash delete operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashCheckFailure 1.3.6.1.4.1.207.8.4.4.4.31.10
The number of flash check operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashEraseFailure 1.3.6.1.4.1.207.8.4.4.4.31.11
The number of flash erase operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashCompactFailure 1.3.6.1.4.1.207.8.4.4.4.31.12
The number of flash compaction operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashVerifyFailure 1.3.6.1.4.1.207.8.4.4.4.31.13
The number of flash verify operations that have failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

flashFailureTrap 1
A flash failure trap is generated when any of the above flash counter is incremented and the failure type is sent in the trap.
TRAP-TYPE    

cc 1.3.6.1.4.1.207.8.4.4.4.37
OBJECT IDENTIFIER    

ccDetailsTable 1.3.6.1.4.1.207.8.4.4.4.37.1
The table of call details parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcDetailsEntry

ccDetailsEntry 1.3.6.1.4.1.207.8.4.4.4.37.1.1
A single entry of ISDN call details. This contains the parameters of a single ISDN call details.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CcDetailsEntry  

ccDetailsIndex 1.3.6.1.4.1.207.8.4.4.4.37.1.1.1
The index of the call details entry in the call details table. When an entry is created in this table, the index does not have to be written. However, to reference the values that are written, an unused index must be found by reading the index values of the table until a no such object error is returned. Attempting to create a row by using an already used index will result in simply changing the parameters of an existing call details entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..128  

ccDetailsName 1.3.6.1.4.1.207.8.4.4.4.37.1.1.2
The name of the ISDN call details. This must be unique for all ISDN call details, when comparisons are done ignoring the case of letters. Valid characters in the ISDN call name include 0-9, a-z, A-Z and '_'. A name consisting of all digits is not valid. Setting this object is mandatory on row creation. However, this object cannot be set for an existing call. This is because for the command line interface calls are identified by name. There is one exception. Setting ccDetailsName to an empty string will cause the call details to be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

ccDetailsRemoteName 1.3.6.1.4.1.207.8.4.4.4.37.1.1.3
The remote ISDN call name. This name can be referenced by certain other call details parameters related with setting up the Q.931 SETUP message for outgoing calls, or searching for calls for incoming calls. Valid characters in the ISDN remote call name include 0-9, a-z, A-Z and '_'. A remote name consisting of all digits is valid.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

ccDetailsCalledNumber 1.3.6.1.4.1.207.8.4.4.4.37.1.1.4
The number called when this call details is activated. The number should include all telephone network access codes, country codes and area codes required to make a call from the particular ISDN interface. Setting this object is mandatory on row creation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

ccDetailsCallingNumber 1.3.6.1.4.1.207.8.4.4.4.37.1.1.5
The number used as the calling number when this call is activated. The calling number can optionally be placed in the outgoing SETUP message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

ccDetailsAlternateNumber 1.3.6.1.4.1.207.8.4.4.4.37.1.1.6
The number called when all retries with the main called number have failed. In this event, the router tries once with the alternate number, then checks the ccDetailsKeepup object to determine whether to try again with the main number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

ccDetailsEnabled 1.3.6.1.4.1.207.8.4.4.4.37.1.1.7
Whether this ISDN call is enabled or disabled for incoming and outgoing calls. If the call details entry is disabled, all existing active calls based on this call details entry are left active.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

ccDetailsDirection 1.3.6.1.4.1.207.8.4.4.4.37.1.1.8
The direction for which calls may be made or received using this call details entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER in-only(1), out-only(2), both(3)  

ccDetailsPrecedence 1.3.6.1.4.1.207.8.4.4.4.37.1.1.9
The precedence of this call details entry in the event of call collision. Call collision occurs when an incoming call for a given details entry is detected while an outgoing call is waiting to complete. This object configures whether the router treats the incoming or outgoing call as having precedence. Since the device at the other end will also probably be experiencing a call collision, the precedence should be configured to the opposite value at the other end. Setting this object is mandatory on row creation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER in(1), out(2)  

ccDetailsHoldupTime 1.3.6.1.4.1.207.8.4.4.4.37.1.1.10
The time, in seconds, that active calls created from this call details should be held up after initial activation. The call will be held up for at least this time, unless cleared from the network. Thus, for example, PPP idle timeouts will not bring the call down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7200  

ccDetailsPreferredIfIndex 1.3.6.1.4.1.207.8.4.4.4.37.1.1.11
The ifIndex of an ISDN interface on this router which is the preferred ISDN interface on which to make an outgoing call using this call details entry. The ifIndex, if not 0, should reference the ifEntry which contains information about the entire ISDN interface, at the lowest layer. If a channel is not available on this interface, the call can try other interfaces in order to make the call. This object is not used on incoming calls. If the value of this object is set to 0, no interface will be preferred over any other. If the value of this object does not reference the ifEntry for the entire ISDN interface, no interface will be preferred.
Status: mandatory Access: read-write
OBJECT-TYPE    
  InterfaceIndexOrZero  

ccDetailsRequiredIfIndex 1.3.6.1.4.1.207.8.4.4.4.37.1.1.12
The ifIndex of an ISDN interface on this router which is the required ISDN interface on which to make an outgoing call using this call details entry. The ifIndex, if not 0, must reference the ifEntry which contains information about the entire ISDN interface, at the lowest layer. If a channel is not available on this interface, the call fails. This object is not used on incoming calls. If the value of this object is set to 0, no interface will be required. If the value of this object does not reference the ifEntry for the entire ISDN interface, no interface will be required.
Status: mandatory Access: read-write
OBJECT-TYPE    
  InterfaceIndexOrZero  

ccDetailsPriority 1.3.6.1.4.1.207.8.4.4.4.37.1.1.13
The priority of calls generated from this call details entry. The priority determines whether calls can be bumped for higher priority calls. The value of priority falls into ranges: 0-19 - call bumped by incoming or outgoing, voice or data calls 20-39 - call bumped by outgoing voice and incoming or outgoing data calls 40-59 - call bumped by emergency voice calls or incoming or outgoing data calls 60-99 - call bumped by emergency voice calls or outgoing data calls. Note that when the call is bumped by a data call, the data call must have higher priority than the call being bumped.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..99  

ccDetailsRetryT1 1.3.6.1.4.1.207.8.4.4.4.37.1.1.14
The time in seconds between retries of calls generated from this call details entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..120  

ccDetailsRetryN1 1.3.6.1.4.1.207.8.4.4.4.37.1.1.15
The number of retries in a retry group for calls generated from this call details entry. Note that the default value means that by default the call will not be retried.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..10  

ccDetailsRetryT2 1.3.6.1.4.1.207.8.4.4.4.37.1.1.16
The time in seconds between retry groups for retries of calls generated from this call details entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 300..1200  

ccDetailsRetryN2 1.3.6.1.4.1.207.8.4.4.4.37.1.1.17
The number of retry groups for calls generated from this call details entry. Note that the default value means that by default no retry groups will be attempted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..5  

ccDetailsKeepup 1.3.6.1.4.1.207.8.4.4.4.37.1.1.18
A flag indicating whether calls generated from this call details entry should be kept up always. Inspection of this flag takes place when a call is cleared from an external source. If set to 'yes', the call will be retried.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ccDetailsOutSetupCli 1.3.6.1.4.1.207.8.4.4.4.37.1.1.19
The CLI information placed into outgoing SETUP messages when this call details is used to generate an outgoing call. The value 'off' means that no CLI information in placed in the SETUP message. The value 'calling' means that the calling number from the call details entry is placed in the SETUP message. The value 'interface' means that the Q.931 interface number for the interface and DLC on which the call is made is placed in the SETUP message. The value 'nonumber' means that the CLI information element is placed in the SETUP message with no number information. The network will fill the number in.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), calling(2), interface(3), nonumber(4)  

ccDetailsOutSetupUser 1.3.6.1.4.1.207.8.4.4.4.37.1.1.20
The user-user information placed into outgoing SETUP messages when this call details is used to generate an outgoing call. The value 'off' means that no user-user information in placed in the SETUP message. The value 'local' means that the call name from the call details entry is placed in the SETUP message. The value 'remote' means that the remote call name from the call details entry is placed in the SETUP message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsOutSetupCalledSub 1.3.6.1.4.1.207.8.4.4.4.37.1.1.21
The called subaddress information placed into outgoing SETUP messages when this call details is used to generate an outgoing call. The value 'off' means that no called subaddress information in placed in the SETUP message. The value 'local' means that the call name from the call details entry is placed in the SETUP message. The value 'remote' means that the remote call name from the call details entry is placed in the SETUP message. Note that the action of this object is overridden by the value of the object ccDetailsOutSubaddress.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsOutSubaddress 1.3.6.1.4.1.207.8.4.4.4.37.1.1.22
This object gives a way to override the called subaddress information placed into outgoing SETUP messages when this call details is used to generate an outgoing call, as given by the ccDetailsOutSetupCalledSub object. The object is an arbitrary string of ASCII characters, from 0 to 31 characters long.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

ccDetailsCallback 1.3.6.1.4.1.207.8.4.4.4.37.1.1.23
A flag indicating whether or not to call back the caller when an incoming call is generated from this call details entry. If set to 'yes', the incoming call will be cleared, and after a short delay, an outgoing call will be activated for this call details entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ccDetailsCallbackDelay 1.3.6.1.4.1.207.8.4.4.4.37.1.1.24
The time, in tenths of a second, which the router will wait after clearing an incoming call whose call details entry specified that the caller should be called back before making the return call. The purpose of this object is to allow the user to specify a delay in callback which will allow the network to properly clear the call at both this end and the remote end.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

ccDetailsInSetupCalledSubSearch 1.3.6.1.4.1.207.8.4.4.4.37.1.1.25
Determines whether this call details entry is used in a search of call details for an incoming call based on the contents of the called subaddress information in the incoming SETUP message. The value 'off' means that this call details entry is not used in the search. The value 'local' means that the call details entry is used in the search and the called subaddress information is compared with the call details entry name. The value 'remote' means that the call details entry is used in the search and the called subaddress information is compared with the call details entry remote name. A number of searches are carried out until a matching call is found. First a search against the called subaddress in the SETUP message, then a search against the user-user information in the SETUP message, then a search against the calling number information in the SETUP message, then a search for any call that is configured to respond to any incoming call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsInSetupUserSearch 1.3.6.1.4.1.207.8.4.4.4.37.1.1.26
Determines whether this call details entry is used in a search of call details for an incoming call based on the contents of the user-user information in the incoming SETUP message. The value 'off' means that this call details entry is not used in the search. The value 'local' means that the call details entry is used in the search and the user-user information is compared with the call details entry name. The value 'remote' means that the call details entry is used in the search and the user-user information is compared with the call details entry remote name. A number of searches are carried out until a matching call is found. First a search against the called subaddress in the SETUP message, then a search against the user-user information in the SETUP message, then a search against the calling number information in the SETUP message, then a search for any call that is configured to respond to any incoming call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsInSetupCliSearch 1.3.6.1.4.1.207.8.4.4.4.37.1.1.27
Determines whether this call details entry is used in a search of call details for an incoming call based on the contents of the calling number information in the incoming SETUP message. The value 'off' means that this call details entry is not used in the search. The value 'on' means that the call details entry is used in the search and the calling number information is compared with the call details entry called number. The value 'list' means that the call details entry is used in the search and the calling number information is compared with the numbers on the CLI list reference by the object ccDetailsInSetupCliSearchList. The value 'list' cannot be set by an SNMP management entity. Rather the ccDetailsInSetupCliSearchList object should be set to a non-zero value, which will automatically set this object to 'list'. A number of searches are carried out until a matching call is found. First a search against the called subaddress in the SETUP message, then a search against the user-user information in the SETUP message, then a search against the calling number information in the SETUP message, then a search for any call that is configured to respond to any incoming call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), on(2), list(3)  

ccDetailsInSetupCliSearchList 1.3.6.1.4.1.207.8.4.4.4.37.1.1.28
If the ccDetailsInSetupCliSearch object is set to 'list', this object gives the index of the CLI list to search. The value of CLI list indices is 1..100. The value 0 is returned when the ccDetailsInSetupCliSearch object is not set to 'list'. If the value of this object is set to 0 via SNMP, then the ccDetailsInSetupCliSearch object will be internally set to 'off'. Subsequently setting the value of this object to a non-zero value will set the ccDetailsInSetupCliSearch object to 'list'. Note that when using the command line interface, CLI list indices range from 0 to 99, but when using SNMP they range from 1 to 100. This is because SNMP will not allow a table index to have the value 0, and the command line usage of indices from 0 to 99 is too well established to change.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

ccDetailsInAnyFlag 1.3.6.1.4.1.207.8.4.4.4.37.1.1.29
Determines whether this call details entry will match any incoming call. After all searched for incoming calls have been carried out based on called subaddress, user-user information and calling number, a search is carried out for the first call found with this flag set to 'yes'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ccDetailsInSetupCalledSubCheck 1.3.6.1.4.1.207.8.4.4.4.37.1.1.30
Determines whether to perform a check when an incoming call matches this call details entry based on the contents of the called subaddress information in the incoming SETUP message. The value 'off' means that the check is not carried out. The value 'local' means that the check is carried out and the called subaddress information is compared with the call details entry name. The value 'remote' means that the check is carried out and the called subaddress information is compared with the call details entry remote name. A number of checks are optionally carried out once a matching call is found. The first check is against the called subaddress in the SETUP message, then against the user-user information in the SETUP message, then against the calling number information in the SETUP message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsInSetupUserCheck 1.3.6.1.4.1.207.8.4.4.4.37.1.1.31
Determines whether to perform a check when an incoming call matches this call details entry based on the contents of the user-user information in the incoming SETUP message. The value 'off' means that the check is not carried out. The value 'local' means that the check is carried out and the user-user information is compared with the call details entry name. The value 'remote' means that the check is carried out and the user-user information is compared with the call details entry remote name. A number of checks are optionally carried out once a matching call is found. The first check is against the called subaddress in the SETUP message, then against the user-user information in the SETUP message, then against the calling number information in the SETUP message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), local(2), remote(3)  

ccDetailsInSetupCliCheck 1.3.6.1.4.1.207.8.4.4.4.37.1.1.32
Determines whether to perform a check and which check to perform when an incoming call matches this call details entry based on the contents of the calling number information in the incoming SETUP message. The value 'off' means that the check is not carried out. The value 'present' means that the check is carried out only if calling number information is present. The value 'required' means that the calling number must be present for the check to pass. When the check is carried out, the calling number information is compared with the numbers in the CLI list referenced by the object ccDetailsInSetupCliCheckList. A number of checks are optionally carried out once a matching call is found. The first check is against the called subaddress in the SETUP message, then against the user-user information in the SETUP message, then against the calling number information in the SETUP message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), present(2), required(3)  

ccDetailsInSetupCliCheckList 1.3.6.1.4.1.207.8.4.4.4.37.1.1.33
If the ccDetailsInSetupCliCheck object is set to 'present' or 'required', this object gives the index of the CLI list to check against. The value of CLI list indices is 1..100. The value 0 means that no list to check against is defined and the check immediately fails. Note that when using the command line interface, CLI list indices range from 0 to 99, but when using SNMP they range from 1 to 100. This is because SNMP will not allow a table index to have the value 0, and the command line usage of indices from 0 to 99 is too well established to change.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

ccDetailsUserType 1.3.6.1.4.1.207.8.4.4.4.37.1.1.34
The type of user of this call. The value 'attach' means that users have to attach to this call before the call can be used for outgoing or incoming calls. The value 'ppp' means that for incoming calls only dynamic PPP interfaces will be created whenever this call details entry is matched.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER attach(1), ppp(2)  

ccDetailsLoginType 1.3.6.1.4.1.207.8.4.4.4.37.1.1.35
The type of login for calls generated using this call details entry, for incoming calls only. Incoming calls can be configured to go through a logging in phase before the call is brought up. This object defines which login types are used. The value 'none' means don't do a login phase. The value 'userdb' means use the user database on the router to check login parameters. The value 'radius' means use the router's configured RADIUS servers to check the login parameters. The values 'pap-tacacs', 'chap' and 'pap-radius' apply only when the user is 'ppp' and determine how the dynamic PPP interface are configured for authentication. The value 'pap-tacacs' means use PAP to authenticate and use the TACACS server to check the login parameters. The value 'pap-radius' means use PAP to authenticate and use the RADIUS server to check the login parameters. The value 'chap' means use CHAP to authenticate. The value 'tacacs' means use the TACACS server to check login parameters. The value 'all' means use the user database, TACACS and RADIUS to check the login parameters. The login parameters for values 'userdb', 'radius', 'tacacs' and 'all' are determined by the ccDetailsUsername and ccDetailsPassword objects.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), userdb(2), radius(3), pap-tacacs(4), chap(5), pap-radius(6), tacacs(7), all(8)  

ccDetailsUsername 1.3.6.1.4.1.207.8.4.4.4.37.1.1.36
The source of the username when the ccDetailsLoginType object has a value of 'userdb', 'radius', 'tacacs' or 'all'. The value 'none' means no username is defined. The value 'cli' means take the username from the calling number information in the SETUP message. The value 'calledsub' means take the username from the called subaddress information in the SETUP message. The value 'useruser' means take the username from the user-user information in the SETUP message. The value 'callname' means take the username from the call details entry name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), cli(2), calledsub(3), useruser(4), callname(5)  

ccDetailsPassword 1.3.6.1.4.1.207.8.4.4.4.37.1.1.37
The source of the password when the ccDetailsLoginType object has a value of 'userdb', 'radius', 'tacacs' or 'all'. The value 'none' means no password is defined. The value 'cli' means take the password from the calling number information in the SETUP message. The value 'calledsub' means take the password from the called subaddress information in the SETUP message. The value 'useruser' means take the password from the user-user information in the SETUP message. The value 'callname' means take the password from the call details entry name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), cli(2), calledsub(3), useruser(4), callname(5)  

ccDetailsBumpDelay 1.3.6.1.4.1.207.8.4.4.4.37.1.1.38
The time, in tenths of a second, which the router will wait after clearing an existing call which has been bumped to make way for a call based on this call details entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

ccDetailsDataRate 1.3.6.1.4.1.207.8.4.4.4.37.1.1.39
The data rate to use for active calls based on this call details entry. The actual data rate for outgoing calls is determined by both this object and the data rate parameter for the Q.931 interface chosen for the call. If either this object or the interface object specify a rate of 56k, then 56k will be the rate for the call. Otherwise, the default rate of 64k will be used. This allows interoperability between ISDNs which only allow 56k of data on a B channel.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER rate-64k(1), rate-56k(2)  

ccDetailsPppTemplate 1.3.6.1.4.1.207.8.4.4.4.37.1.1.40
The PPP template to use when creating dynamic PPP interfaces for calls generated from this call details entry. The value 33 represents a default PPP template, the values 1 to 32 represent PPP templates that are currently defined in the router. Note that when using the command line interface, PPP template indices range from 0 to 31, but when using SNMP they range from 1 to 32. This is because SNMP will not allow a table index to have the value 0. While there is no PPP template table accessible via SNMP, if there was, the indices of the table would have to range from 1 to 32.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..33  

ccDetailsUserModule 1.3.6.1.4.1.207.8.4.4.4.37.1.1.41
The module ID of the user module currently attached to this ISDN call details entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccDetailsNumberAttachments 1.3.6.1.4.1.207.8.4.4.4.37.1.1.42
The number of attachments from the user module currently attached to this call details entry. The ccAttachmentsTable gives the actual attachments for each call details entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccCliListTable 1.3.6.1.4.1.207.8.4.4.4.37.2
The table of CLI list entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcCliListEntry

ccCliListEntry 1.3.6.1.4.1.207.8.4.4.4.37.2.1
A single entry in the CLI list table. This contains a single number, as well as index information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CcCliListEntry  

ccCliListListIndex 1.3.6.1.4.1.207.8.4.4.4.37.2.1.1
The index of the CLI list. CLI lists from 1 to 100 are defined in the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..100  

ccCliListEntryIndex 1.3.6.1.4.1.207.8.4.4.4.37.2.1.2
The index of the CLI list entry within the CLI list. The minimum CLI list entry is 1. CLI lists are unlimited in length, although internal memory requirements could result in failure to create a given entry. When creating a row in this table, the entry index should be set to index the first empty row. Only one CLI list row in a given list should be created in any one SNMP message. Attempting to create more than one row will result in failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccCliListNumber 1.3.6.1.4.1.207.8.4.4.4.37.2.1.3
The number for this CLI list entry. Setting the number to a zero length string removes the entry from the CLI list, with consequent reshuffling of CLI entry indices. Thus the easiest way to delete an entire CLI list is to repeatedly set the first element in the list to a zero length string. A failure to SET will occur when this is attempted on an empty list.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

ccActiveCallTable 1.3.6.1.4.1.207.8.4.4.4.37.3
The table of ISDN active calls.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcActiveCallEntry

ccActiveCallEntry 1.3.6.1.4.1.207.8.4.4.4.37.3.1
A single entry in the active call table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CcActiveCallEntry  

ccActiveCallIndex 1.3.6.1.4.1.207.8.4.4.4.37.3.1.1
The index of the active call. There are 128 possible active calls in the router simultaneously.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..128  

ccActiveCallDetailsIndex 1.3.6.1.4.1.207.8.4.4.4.37.3.1.2
The index of the call details entry which generated this active call. Thus the index into the ccDetailsTable for this call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..128  

ccActiveCallIfIndex 1.3.6.1.4.1.207.8.4.4.4.37.3.1.3
The interface index of the interface on which this active call is being made or received. A value of zero indicates that the active has not yet had an interface assigned to it. The ifEntry indexed by this object is the ifEntry for the entire ISDN interface, not the ifEntry for the active call's B channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

ccActiveCallDataRate 1.3.6.1.4.1.207.8.4.4.4.37.3.1.4
The data rate in use for this active call. This is determined by the call details setting of data rate, the ISDN interface setting for data rate, and the contents of the bearer capability information in the incoming SETUP message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER rate-64k(1), rate-56k(2)  

ccActiveCallState 1.3.6.1.4.1.207.8.4.4.4.37.3.1.5
The state of this active call. The value 'null' indicates that this active call does not actually exist, in other words it is in the process of being created or destroyed. The value 'off' means that the active call is just being activated. The value 'try' means that the active call is attempting to establish. The value 'on' means that the active call is established. The value 'wait' means that the active call is waiting to retry. The value 'await1' means that the active call is waiting for authentication to succeed before becoming established.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER null(1), off(2), try(3), on(4), wait(5), await1(6)  

ccActiveCallDirection 1.3.6.1.4.1.207.8.4.4.4.37.3.1.6
The direction of this active call. The value 'in' indicates that this active call is an incoming call, the value 'out' indicates that the active call is an outgoing call. The value 'undefined' indicates that the active call has just been created and a direction has not been assigned to it yet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in(1), out(2), undefined(3)  

ccActiveCallUserModule 1.3.6.1.4.1.207.8.4.4.4.37.3.1.7
The module ID of the user module attached to this ISDN active call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccActiveCallUserInstance 1.3.6.1.4.1.207.8.4.4.4.37.3.1.8
The instance of the user module attached to this ISDN active call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccActiveCallBchannelIndex 1.3.6.1.4.1.207.8.4.4.4.37.3.1.9
The B channel number for this active entry. BRI interfaces have B channels in the range 1..2, PRI interfaces have B channels in the range 1..31, excluding a channel which is the D channel. A value of 0 for this entry means that either a B channel is not currently allocated for this call, or that more than one B channel is allocated. In the second case, the management client will have to walk the B channel allocation table looking for channels with the same active call index as this call's.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..31  

ccCallLogTable 1.3.6.1.4.1.207.8.4.4.4.37.4
The table of ISDN call log entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcCallLogEntry

ccCallLogEntry 1.3.6.1.4.1.207.8.4.4.4.37.4.1
A single entry in the ISDN call log table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CcCallLogEntry  

ccCallLogIndex 1.3.6.1.4.1.207.8.4.4.4.37.4.1.1
The index of the call log entry. Since the call log table is dynamic, there is no guarantee that this index will continue to refer to the same log entry over time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccCallLogName 1.3.6.1.4.1.207.8.4.4.4.37.4.1.2
The name of the call details entry which generated the active call for which this is the log entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

ccCallLogState 1.3.6.1.4.1.207.8.4.4.4.37.4.1.3
The state of the log entry. The value 'initial' means that the call is being established. The value 'active' means that the call is currently established. The value 'disconnected' means that the call was disconnected after being established for some time. The value 'cleared' means that the call was cleared abormally while in the establishment phase.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initial(1), active(2), disconnected(3), cleared(4)  

ccCallLogTimeStarted 1.3.6.1.4.1.207.8.4.4.4.37.4.1.4
A string in the format 'dd-mmm-yyyy hh:mm:ss' which gives the start time of the call for which this is the log entry. If the call never reached or has not yet reached the active state, this object will be a zero-length string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

ccCallLogDirection 1.3.6.1.4.1.207.8.4.4.4.37.4.1.5
The direction of the call for which this is the log entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in(1), out(2)  

ccCallLogDuration 1.3.6.1.4.1.207.8.4.4.4.37.4.1.6
The duration in seconds, of the call for which this is the log entry. A value of 0 in this field means either that the call has just started, that the call was cleared before becoming established, or that the call is still active. In other words, a non-zero value is present in this object only for calls which reach establishment and have since been cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccCallLogRemoteNumber 1.3.6.1.4.1.207.8.4.4.4.37.4.1.7
For incoming calls, the calling number, if this was made available in the SETUP message. For outgoing calls, the number dialed. If the number was not available, this object is a zero length string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

ccAttachmentTable 1.3.6.1.4.1.207.8.4.4.4.37.5
The table of call detail attachment entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcAttachmentEntry

ccAttachmentEntry 1.3.6.1.4.1.207.8.4.4.4.37.5.1
A single entry in the attachment table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CcAttachmentEntry  

ccAttachmentDetailsIndex 1.3.6.1.4.1.207.8.4.4.4.37.5.1.1
The index of the call details entry to which this attachment entry belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..128  

ccAttachmentEntryIndex 1.3.6.1.4.1.207.8.4.4.4.37.5.1.2
The index of the attachment entry within the attachment list.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccAttachmentActiveCallIndex 1.3.6.1.4.1.207.8.4.4.4.37.5.1.3
The index of the active call for this attachment. A value of 0 indicates that there is currently no active call for this attachment. A value of 1 to 128 references the active call currently in place for this attachment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

ccAttachmentUserInstance 1.3.6.1.4.1.207.8.4.4.4.37.5.1.4
The instance of the user module attached to the ISDN active call for this attachment. This object should return the same value as the object ccActiveCallUserInstance for the active call indexed by ccAttachmentActiveCallIndex, if this is not 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccBchannelTable 1.3.6.1.4.1.207.8.4.4.4.37.6
The table of B channel attachment entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CcBchannelEntry

ccBchannelEntry 1.3.6.1.4.1.207.8.4.4.4.37.6.1
A single entry in the B channel attachment table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CcBchannelEntry  

ccBchannelIfIndex 1.3.6.1.4.1.207.8.4.4.4.37.6.1.1
The interface index of the interface which this B channel entry is on. The ifEntry indexed by this object is the ifEntry for the entire ISDN interface, not the ifEntry for the active call's B channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccBchannelChannelIndex 1.3.6.1.4.1.207.8.4.4.4.37.6.1.2
The B channel number for this B channel entry. BRI interfaces have B channels in the range 1..2, PRI interfaces have B channels in the range 1..31, excluding a channel which is the D channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..31  

ccBchannelAllocated 1.3.6.1.4.1.207.8.4.4.4.37.6.1.3
A flag indicating whether this B channel is actually allocated to a call or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

ccBchannelCallType 1.3.6.1.4.1.207.8.4.4.4.37.6.1.4
The type of call on this B channel. If the B channel is not allocated, the call type will be undefined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER undefined(1), data(2), voice(3), x25(4)  

ccBchannelActiveCallIndex 1.3.6.1.4.1.207.8.4.4.4.37.6.1.5
The index of the active call which is currently attached to this B channel. If the value of this object is 0 the channel is either not allocated, or is not allocated to a data call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

ccBchannelPriority 1.3.6.1.4.1.207.8.4.4.4.37.6.1.6
The priority of the call which has this B channel allocated to it. This is in the range 0..99 for data calls, 150 for voice calls and 200 for emergency voice calls. A B channel which is not allocated will have a priority of 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ccBchannelDirection 1.3.6.1.4.1.207.8.4.4.4.37.6.1.7
The direction of the call which has this B channel allocated to it. If this B channel is not allocated the value will be 'unallocated'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in(1), out(2), unallocated(3)  

bri 1.3.6.1.4.1.207.8.4.4.4.41
OBJECT IDENTIFIER    

briIntTable 1.3.6.1.4.1.207.8.4.4.4.41.1
The table of BRI interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BriIntEntry

briIntEntry 1.3.6.1.4.1.207.8.4.4.4.41.1.1
A single entry in the BRI interfaces table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BriIntEntry  

briIntIndex 1.3.6.1.4.1.207.8.4.4.4.41.1.1.1
The ifIndex of the BRI interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

briIntBoardIndex 1.3.6.1.4.1.207.8.4.4.4.41.1.1.2
The index in the arBoardTable of the board on which this BRI interface resides.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

briIntBoardPosition 1.3.6.1.4.1.207.8.4.4.4.41.1.1.3
The position on this BRI interface's board of this BRI interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

briIntMode 1.3.6.1.4.1.207.8.4.4.4.41.1.1.4
The mode of operation of this BRI interface. The value isdn means that the entire interface is operating as an ISDN interface, the value tdm means that the entire interface is operating as TDM groups and the value mixed means that some channels in the interface are dedicated to ISDN and some to TDM groups.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER isdn(1), tdm(2), mixed(3)  

briIntTdmChannelMap 1.3.6.1.4.1.207.8.4.4.4.41.1.1.5
A bit map of the channels in the BRI interface which are dedicated to TDM. Channel B1 has channel map value of 1, channel B2 has a channel map value of 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

briIntIsdnChannelMap 1.3.6.1.4.1.207.8.4.4.4.41.1.1.6
A bit map of the channels in the BRI interface which are dedicated to ISDN. Channel B1 has channel map value of 1, channel B2 has a channel map value of 2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

briChanTable 1.3.6.1.4.1.207.8.4.4.4.41.2
The table of channels on BRI interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BriChanEntry

briChanEntry 1.3.6.1.4.1.207.8.4.4.4.41.2.1
A single entry in the BRI channels table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BriChanEntry  

briChanIntIndex 1.3.6.1.4.1.207.8.4.4.4.41.2.1.1
The ifIndex of the BRI interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

briChanChannelIndex 1.3.6.1.4.1.207.8.4.4.4.41.2.1.2
The channel index of the BRI channel. Channel B1 has index 1, channel B2 has index 2 and the D channel has index 3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

briChanMode 1.3.6.1.4.1.207.8.4.4.4.41.2.1.3
The mode of this BRI channel. The value isdn means that the channel is reserved for use in ISDN calls. The value tdm means that the channel is reserved for use by TDM. For the D channel, this object will always have the value isdn.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER isdn(1), tdm(2), none(3)  

briChanState 1.3.6.1.4.1.207.8.4.4.4.41.2.1.4
The state of this BRI channel. The value inactive means that the channel does not currently have an active user, either an ISDN call or an active TDM group. The value active means that the channel is in use, either by an ISDN call or an active TDM group. For the D channel, this object will have the value active if LAPD is using the D channel (either for call control or X.25), or the value inactive otherwise.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

pri 1.3.6.1.4.1.207.8.4.4.4.42
OBJECT IDENTIFIER    

priIntTable 1.3.6.1.4.1.207.8.4.4.4.42.1
The table of PRI interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PriIntEntry

priIntEntry 1.3.6.1.4.1.207.8.4.4.4.42.1.1
A single entry in the PRI interfaces table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PriIntEntry  

priIntIndex 1.3.6.1.4.1.207.8.4.4.4.42.1.1.1
The ifIndex of the PRI interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

priIntBoardIndex 1.3.6.1.4.1.207.8.4.4.4.42.1.1.2
The index in the arBoardTable of the board on which this PRI interface resides.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

priIntBoardPosition 1.3.6.1.4.1.207.8.4.4.4.42.1.1.3
The position on this PRI interface's board of this PRI interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

priIntMode 1.3.6.1.4.1.207.8.4.4.4.42.1.1.4
The mode of operation of this PRI interface. The value isdn means that the entire interface is operating as an ISDN interface, the value tdm means that the entire interface is operating as TDM groups and the value mixed means that some channels in the interface are dedicated to ISDN and some to TDM groups.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER isdn(1), tdm(2), mixed(3)  

priIntTdmChannelMap 1.3.6.1.4.1.207.8.4.4.4.42.1.1.5
A bit map of the channels in the PRI interface which are dedicated to TDM. PRI channels are numbered from 0 to 31, 0 is unused, 16 (E1) or 24 (T1) is the D channel. The map values are 2 to the power of the channel number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

priIntIsdnChannelMap 1.3.6.1.4.1.207.8.4.4.4.42.1.1.6
A bit map of the channels in the PRI interface which are dedicated to ISDN. PRI channels are numbered from 0 to 31, 0 is unused, 16 (E1) or 24 (T1) is the D channel. The map values are 2 to the power of the channel number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

priIntType 1.3.6.1.4.1.207.8.4.4.4.42.1.1.7
The type of primary rate interface. E1 has 30 B + D channel, T1 has 23 B + D channel. If the value unknown is returned for this object, the exact PRI type has not yet been determined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER e1(1), t1(2), unknown(3)  

priChanTable 1.3.6.1.4.1.207.8.4.4.4.42.2
The table of channels on PRI interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PriChanEntry

priChanEntry 1.3.6.1.4.1.207.8.4.4.4.42.2.1
A single entry in the PRI channels table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PriChanEntry  

priChanIntIndex 1.3.6.1.4.1.207.8.4.4.4.42.2.1.1
The ifIndex of the PRI interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

priChanChannelIndex 1.3.6.1.4.1.207.8.4.4.4.42.2.1.2
The channel index of the PRI channel. Valid channels have indices from 1 to 31. The D channel on an E1 interface has index 16, the D channel on a T1 interface has index 24.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..31  

priChanMode 1.3.6.1.4.1.207.8.4.4.4.42.2.1.3
The mode of this PRI channel. The value isdn means that the channel is reserved for use in ISDN calls. The value tdm means that the channel is reserved for use by TDM. For the D channel, this object will usually have the value isdn. An exception is if the interface is running common D channel mode and the D channel is reserved for TDM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER isdn(1), tdm(2), neither(3)  

priChanState 1.3.6.1.4.1.207.8.4.4.4.42.2.1.4
The state of this PRI channel. The value inactive means that the channel does not currently have an active user, either an ISDN call or an active TDM group. The value active means that the channel is in use, either by an ISDN call or an active TDM group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

loader 1.3.6.1.4.1.207.8.4.4.4.48
OBJECT IDENTIFIER    

loadTable 1.3.6.1.4.1.207.8.4.4.4.48.1
The table of load parameters, dynamic and static.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LoadEntry

loadEntry 1.3.6.1.4.1.207.8.4.4.4.48.1.1
A single entry of load parameters. This contains the parameters required to perform a load from the router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LoadEntry  

loadIndex 1.3.6.1.4.1.207.8.4.4.4.48.1.1.1
There are two sets of load information, dynamic and static. The dynamic information is used once, then cleared. The static information is used whenever the dynamic information is not available. The dynamic information is also used to indicate the current load parameters when a load is in progress.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

loadServer 1.3.6.1.4.1.207.8.4.4.4.48.1.1.2
The IP address from which load will load.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

loadDestination 1.3.6.1.4.1.207.8.4.4.4.48.1.1.3
The destination of the file loaded, either flash or nvs memory, or undefined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER undefined(1), nvs(2), flash(3)  

loadFilename 1.3.6.1.4.1.207.8.4.4.4.48.1.1.4
The file name of the file being loaded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

loadDelay 1.3.6.1.4.1.207.8.4.4.4.48.1.1.5
A delay in seconds between the initiation of the load and the start of the load. This allows for time to set up TFTP servers in cases where the terminal and TFTP server are using the same piece of equipment but will not work simultaneously.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

loadStatus 1.3.6.1.4.1.207.8.4.4.4.48.2
Status and action object for the load module. The values 1 to 5 are read-only values and reflect the state of the load module. Values 4 and 5 (complete and reset) are 'read-once', that is, if their values are read, either by SNMP or by manager console command, then they will be changed back to idle(1). The action values (6 and 7) cause a start and stop of the load process respectively. Starting the load can only occur if this field has the values 1, 4, or 5. Stopping the load can only occur is this field has the values 2 or 3. Reading the value of the loadStatus after one of actionstart or actionstop has been set will give one of the values 1 to 5. Note: A single exception to the above rules is that if the value of loadStatus is idle(1), then a write of 1 to this variable will succeed without generating an error. This exception is to allow certain SNMP test suites to test this variable without throwing up errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER idle(1), wait(2), loading(3), complete(4), reset(5), actionstart(6), actionstop(7)  

install 1.3.6.1.4.1.207.8.4.4.4.49
OBJECT IDENTIFIER    

installTable 1.3.6.1.4.1.207.8.4.4.4.49.1
The list of install configurations for the router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    InstallEntry

installEntry 1.3.6.1.4.1.207.8.4.4.4.49.1.1
An entry in the list of install configurations.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  InstallEntry  

instIndex 1.3.6.1.4.1.207.8.4.4.4.49.1.1.1
The index for the install table. There are four install configurations defined in the router, default, preferred, temporary and current. The router will attempt to use these in the order temporary, preferred, default when it boots. An install that is undefined will be skipped, an install which points to a file which is not present will be skipped. When the temporary install is used, the information is deleted. The current configuration shows what the router currently has installed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER temporary(1), preferred(2), default(3), current(4)  

instRelDevice 1.3.6.1.4.1.207.8.4.4.4.49.1.1.2
The device for the release in the install. If the device is flash the file for the release is given in instRelName. Devices none(1) or flash(3) are invalid for the default(3) release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), eprom(2), flash(3)  

instRelName 1.3.6.1.4.1.207.8.4.4.4.49.1.1.3
The file name for the release in the install, if the instRelDevice is flash(3). If the instRelDevice is none(1) or eprom(2), this object should be a null string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

instRelMajor 1.3.6.1.4.1.207.8.4.4.4.49.1.1.4
The major release number for this install. This information is obtained by the router when the other elements in the row are set and is thus not directly set by management. If the release number is a.b.c, the major release number is a.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

instRelMinor 1.3.6.1.4.1.207.8.4.4.4.49.1.1.5
The minor release number for this install. This information is obtained by the router when the other elements in the row are set and is thus not directly set by management. If the release number is a.b.c, the major release number is b.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

instPatDevice 1.3.6.1.4.1.207.8.4.4.4.49.1.1.6
The device for the patch in the install. The file for the patch is given in instPatName unless the device is none(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), flash(3), nvs(4)  

instPatName 1.3.6.1.4.1.207.8.4.4.4.49.1.1.7
The file name for the patch in the install.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

instRelInterim 1.3.6.1.4.1.207.8.4.4.4.49.1.1.8
The interim release number for this install. This information is obtained by the router when the other elements in the row are set and is thus not directly set by management. If the release number is a.b.c, the major release number is c. If the release number is a.b, the interim release number is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

instRelExists 1.3.6.1.4.1.207.8.4.4.4.49.1.1.9
Indicates if the release file exists or not. true(1) means it exists, false(2) means it doesn't.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

instPatExists 1.3.6.1.4.1.207.8.4.4.4.49.1.1.10
Indicates if the patch file exists or not. true(1) means it exists, false(2) means it doesn't
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

installHistoryTable 1.3.6.1.4.1.207.8.4.4.4.49.2
The table of descriptions of events in the install history of the router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    InstallHistoryEntry

installHistoryEntry 1.3.6.1.4.1.207.8.4.4.4.49.2.1
A single line describing part of the install history of the router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  InstallHistoryEntry  

instHistIndex 1.3.6.1.4.1.207.8.4.4.4.49.2.1.1
The index of this event in the install history. Indices run from 1 to the maximum number. The maximum number is not available as a managed object so this table will have to be traversed in order to find out how large it is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

instHistLine 1.3.6.1.4.1.207.8.4.4.4.49.2.1.2
A line of text describing a single event in the install history of the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

configFile 1.3.6.1.4.1.207.8.4.4.4.49.3
The name of the file that the router will configure from at boot. The format of the name is the same as that for fileName described above. If the configuration file name is a zero length string, then there is no configuration file defined in the router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

licenceTable 1.3.6.1.4.1.207.8.4.4.4.49.4
The list of release licences in the router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LicenceEntry

licenceEntry 1.3.6.1.4.1.207.8.4.4.4.49.4.1
An entry in the list of release licences.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LicenceEntry  

licenceIndex 1.3.6.1.4.1.207.8.4.4.4.49.4.1.1
A unique licence index. Licence indices are recalculated every time the router reboots to reflect the current licences on the router. As licences are added, new indices are allocated to the new licences.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

licenceStatus 1.3.6.1.4.1.207.8.4.4.4.49.4.1.2
The status of the file. When read, this object will always return a value of ok(1), since the object will not exist if the value is deleting(2). Write the value deleting(2) to this object to delete the file.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ok(1), deleting(2)  

licenceRelease 1.3.6.1.4.1.207.8.4.4.4.49.4.1.3
The file name for the release whose licence this is.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

licenceMajor 1.3.6.1.4.1.207.8.4.4.4.49.4.1.4
The major release number for the release whose licence this is.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

licenceMinor 1.3.6.1.4.1.207.8.4.4.4.49.4.1.5
The minor release number for the release whose licence this is.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

licencePassword 1.3.6.1.4.1.207.8.4.4.4.49.4.1.6
The password for this release. The password is a string of hex digits.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(12)  

licenceExpiry 1.3.6.1.4.1.207.8.4.4.4.49.4.1.7
A human-readable string that gives the expiry date of this licence.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

licenceInterim 1.3.6.1.4.1.207.8.4.4.4.49.4.1.8
The interim release number for the release whose licence this is.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

createConfigFile 1.3.6.1.4.1.207.8.4.4.4.49.5
The name of a file to create containing the current router configuration. A read from this variable will return the same as the variable configFile. Thus to save the current configuration in the current configuration file, read createConfigFile first, then write the result back to createConfigFile. If this variable is written with the name of an existing file, the file will be replaced with the current configuration.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..255)  

configFileExist 1.3.6.1.4.1.207.8.4.4.4.49.6
Indicates if the boot configuration file exists or not. true(1) means it exists, false(2) means it doesn't
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

configFileExistTrap 1
This trap is generated when the boot file is detected as missing
TRAP-TYPE    

currentConfigFile 1.3.6.1.4.1.207.8.4.4.4.49.7
The name of the file that the router is currently configured with. The format of the name is the same as that for fileName described above. If the current configuration file name is a zero length string, then there is no current configuration file defined in the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

trigger 1.3.6.1.4.1.207.8.4.4.4.53
OBJECT IDENTIFIER    

triggerLastTriggerActivated 1.3.6.1.4.1.207.8.4.4.4.53.1
The trigger number of the most recent trigger activated on this router. This is also the variable sent in the trigger trap below. If no triggers have been activated yet since the last restart of this router, this variable will read as 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

triggerTrap 1
A trigger trap is generated a trigger is activated. The number of the trigger activated is given by the variable triggerLastTriggerActivated.
TRAP-TYPE    

file 1.3.6.1.4.1.207.8.4.4.4.56
OBJECT IDENTIFIER    

fileTable 1.3.6.1.4.1.207.8.4.4.4.56.1
A list of all the files in the router's non-volatile storage.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FileEntry

fileEntry 1.3.6.1.4.1.207.8.4.4.4.56.1.1
An entry in the list of files containing information about a single file in the router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FileEntry  

fileIndex 1.3.6.1.4.1.207.8.4.4.4.56.1.1.1
A unique file index. File indices are recalculated every time the router reboots to reflect the current files on the router. As files are added, new indices are allocated to the new files.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fileName 1.3.6.1.4.1.207.8.4.4.4.56.1.1.2
The name of the file, in the form . The name is up to eight characters long, the type is up to three characters long.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

fileDevice 1.3.6.1.4.1.207.8.4.4.4.56.1.1.3
The device on which the file resides.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER flash(1), nvs(2)  

fileCreationTime 1.3.6.1.4.1.207.8.4.4.4.56.1.1.4
The creation date and time for the file, in the format .
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

fileStatus 1.3.6.1.4.1.207.8.4.4.4.56.1.1.5
The status of the file. When read, this object will always return a value of ok(1), since the object will not exist if the value is deleting(2). Write the value deleting(2) to this object to delete the file.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ok(1), deleting(2)  

fileSize 1.3.6.1.4.1.207.8.4.4.4.56.1.1.6
The size, in bytes, of the file.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fileNumbers 1.3.6.1.4.1.207.8.4.4.4.56.2
The total number of files in FLASH and NVS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ping 1.3.6.1.4.1.207.8.4.4.4.58
OBJECT IDENTIFIER    

pingTable 1.3.6.1.4.1.207.8.4.4.4.58.1
The table of ping parameters, dynamic and static.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PingEntry

pingEntry 1.3.6.1.4.1.207.8.4.4.4.58.1.1
A single entry of ping parameters. This contains the parameters required to perform a ping from the router. The ping specified by the dynamic parameters, can be initiated or stopped at any time by altering the pingStatus accordingly.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PingEntry  

pingIndex 1.3.6.1.4.1.207.8.4.4.4.58.1.1.1
There are two sets of ping information, dynamic and static. The dynamic information is used only once, for the next ping, then automatically replaced with the static information. The static information is used whenever specific dynamic information is not specified. The dynamic information indicates the current ping parameters when a ping is in progress. If static information is not specified, defaults are used. Static information can be changed at any time, but dynamic information cannot be changed while a ping is in progress. A change to the static information when a ping is not currently active, also updates the dynamic information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

pingProtocol 1.3.6.1.4.1.207.8.4.4.4.58.1.1.2
The protocol that the ping will use. The protocol must match the destination address. Ping supports both IP, IPX, Appletalk, and OSI addresses. The protocol must be specified before the address is set, because when the protocol is changed, address is reset to undefined. The default value for this variable is undefined(0).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER undefined(0), apple(1), ip(2), ipx(3), osi(4)  

pingAddress 1.3.6.1.4.1.207.8.4.4.4.58.1.1.3
The address specifies the destination address for ping packets for Appletalk, IP, IPX and OSI networks, respectively. The address format must match the protocol being used. The protocol must be specified before the address is set, because changing the protocol resets the address to undefined. The default value for this variable is an undefined address which is coded as a zero length octet string.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

pingNumberOfPackets 1.3.6.1.4.1.207.8.4.4.4.58.1.1.4
The number of ping packets to transmit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pingPacketSize 1.3.6.1.4.1.207.8.4.4.4.58.1.1.5
The packet size parameter specifies the length in bytes, of data to include in the data portion of the ping packet. The protocol packet header size and the size of headers for the particular link protocol in use have to be added to the packet size to get the total size of the ping packet. The maximum pingPacketSize can be set to is 1500.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1500  

pingTimeout 1.3.6.1.4.1.207.8.4.4.4.58.1.1.6
Timeout specifies the amount of time to wait for a response to a ping packet. Timeout must be greater than zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pingDelay 1.3.6.1.4.1.207.8.4.4.4.58.1.1.7
The delay parameter specifies the time interval, in seconds, between ping packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pingTrapOnCompletion 1.3.6.1.4.1.207.8.4.4.4.58.1.1.8
Specifies whether a trap should be issued on completion of the sequence of pings.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

pingTypeOfService 1.3.6.1.4.1.207.8.4.4.4.58.1.1.9
The Type Of Service (TOS) parameter is only valid for IP addresses, and specifies the TOS field in the IP header of the ping packet, as a decimal in the range 0 to 255.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

pingPattern 1.3.6.1.4.1.207.8.4.4.4.58.1.1.10
The pattern parameter specifies the data pattern to use in the data portion of the ping packet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pingStatus 1.3.6.1.4.1.207.8.4.4.4.58.2
Status and action object for the ping module. A status of '1' indicates that the ping is currently running, the status can be set to '2' to stop the ping. A status of '2' indicates that the ping is currently stopped, the pingStatus can be set to '1' to start the ping. The parameters for the ping can be altered in the pingTable. The destination ping address and protocol have defaults of undefined and must be specified before a ping can be started. The ping statistics are reset to defaults when a ping is started, and updated when the ping stops. Dynamic pingTable information is used only once, for the next ping. Static pingTable information is used for all pings by default, whenever the respective dynamic settings are not specified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER start-running(1), stop-stopped(2)  

pingStatistics 1.3.6.1.4.1.207.8.4.4.4.58.3
OBJECT IDENTIFIER    

pingSentPackets 1.3.6.1.4.1.207.8.4.4.4.58.3.1
The number of ping packets sent to the target in the last ping. The default before the completion of a ping is zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pingReceivedPackets 1.3.6.1.4.1.207.8.4.4.4.58.3.2
The number of packets received from the target in the last ping. The default before the completion of a ping is zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pingMinimumRoundTripTime 1.3.6.1.4.1.207.8.4.4.4.58.3.3
The quickest round trip time taken by any of the ping packets in milliseconds in the last ping. The default before the completion of a ping is negative one.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pingAverageRoundTripTime 1.3.6.1.4.1.207.8.4.4.4.58.3.4
The average round trip time taken by the ping packets in milliseconds in the last ping. The default before the completion of a ping is zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pingMaximumRoundTripTime 1.3.6.1.4.1.207.8.4.4.4.58.3.5
The slowest round trip time taken by any of the ping packets in milliseconds in the last ping. The default before the completion of a ping is zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pingTrap 1
A ping trap is generated when a ping has completed. Traps are only generated if the variable pingTrapOnCompletion is set to true(1) in the dynamic ping entry. A trap is still generated if the ping is stopped prematurely by setting the variable pingStatus to stop/stopped(2).
TRAP-TYPE    

dhcp 1.3.6.1.4.1.207.8.4.4.4.70
OBJECT IDENTIFIER    

dhcpRangeTable 1.3.6.1.4.1.207.8.4.4.4.70.1
The table of DHCP ranges.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpRangeEntry

dhcpRangeEntry 1.3.6.1.4.1.207.8.4.4.4.70.1.1
A single entry of the DHCP range table. This contains information about a single DHCP range configured on this device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DhcpRangeEntry  

dhcpRangeIndex 1.3.6.1.4.1.207.8.4.4.4.70.1.1.1
The index of this DHCP range. DHCP ranges are stored in a list which is ordered by range name. The index gives the place in the list. Note that if ranges are added or deleted, the index for a given range will change. Since this table is read-only, this will not have an undue effect, but if in future this table is made read-write, a mechanism will have to be created to lock the indices of the range table while SET operations are proceeding.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dhcpRangeName 1.3.6.1.4.1.207.8.4.4.4.70.1.1.2
The name given to identify this DHCP range. This is the ultimate method for uniquely identifying this range. Names are compared without regard to case, for example >range1< will be treated as the same as >RANGE1<.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..15)  

dhcpRangeBaseAddress 1.3.6.1.4.1.207.8.4.4.4.70.1.1.3
The base address of this range. This address defines the lower bound of the range of IP addresses which can be allocated to devices requesting an IP address via DHCP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpRangeNumberOfAddresses 1.3.6.1.4.1.207.8.4.4.4.70.1.1.4
The number of IP address in this range. This number defines the upper bound of the range of IP addresses which can be allocated to devices requesting an IP address via DHCP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..256  

dhcpRangeGateway 1.3.6.1.4.1.207.8.4.4.4.70.1.1.5
The IP address of the BOOTP relay agent which will be relaying DHCP requests for this range. If this address is 0.0.0.0, then there will be no BOOTP relay agent and the range will be allocated to devices directly connected to this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpTrapVariable 1.3.6.1.4.1.207.8.4.4.4.70.2
OBJECT IDENTIFIER    

dhcpRangeExhaustedGateway 1.3.6.1.4.1.207.8.4.4.4.70.2.1
Whenever a DHCP client attempts to lease an IP address and the DHCP server cannot provide an address, this variable is set to the gateway address of the DHCP request. The gateway address is the IP address of the gateway acting as a BOOTP relay agent for the request. If there is no gateway, the address will be 0.0.0.0. If the gateway address is non-zero, the DHCP range from which the allocation should have been made will able to be identified by lookup in the DHCP range table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpRangeExhaustedInterface 1.3.6.1.4.1.207.8.4.4.4.70.2.2
Whenever a DHCP client attempts to lease an IP address and the DHCP server cannot provide an address, this variable is set to the IP address of the interface which received the DHCP request. If the gateway address associated with the failed DHCP request is 0.0.0.0, the interface address will be able to be used to lookup the range that was exhausted and from which the allocation should have been made.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpRangeExhaustedTrap 1
This trap is generated when a DHCP client makes a request for an IP address and the request cannot be satisfied because all addresses in the range are already allocated to other devices.
TRAP-TYPE    

dhcpClientTable 1.3.6.1.4.1.207.8.4.4.4.70.3
The table of defined DHCP range client addresses.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpClientEntry

dhcpClientEntry 1.3.6.1.4.1.207.8.4.4.4.70.3.1
A single entry of the DHCP range client table. This contains information about a single DHCP range client address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DhcpClientEntry  

dhcpClientIpAddress 1.3.6.1.4.1.207.8.4.4.4.70.3.1.1
An IP address from the range of available addresses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpClientID 1.3.6.1.4.1.207.8.4.4.4.70.3.1.2
The hardware address of the client, if any, that has been assigned the IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

dhcpClientState 1.3.6.1.4.1.207.8.4.4.4.70.3.1.3
The state of the IP address; one of unused, inuse or reclaim.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unused(0), reclaiming(1), inuse(2), offered(3)  

dhcpClientType 1.3.6.1.4.1.207.8.4.4.4.70.3.1.4
The type of allocation mechanism applied to the IP address; one of static, auto or dyn.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER auto(1), dyn(2), static(3)  

dhcpClientExpiry 1.3.6.1.4.1.207.8.4.4.4.70.3.1.5
The expiry date for dynamically allocated IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

firewall 1.3.6.1.4.1.207.8.4.4.4.77
OBJECT IDENTIFIER    

firewallTrapMessage 1.3.6.1.4.1.207.8.4.4.4.77.1
The last message sent in a firewall TRAP. This variable is really just a placeholder for the object sent in the firewall TRAP, but can be read independently if required. Note however that a new TRAP will cause this variable to be overwritten.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

firewallTrap 1
A firewall trap is generated when the firewall detects an intrusion or attack and notifies the router manager. Firewall trap notifications are enabled with the command ENABLE FIREWALL NOTIFY=SNMP.
TRAP-TYPE    

swi 1.3.6.1.4.1.207.8.4.4.4.87
OBJECT IDENTIFIER    

swiPortTable 1.3.6.1.4.1.207.8.4.4.4.87.1
Table of port properties.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwiPortEntry

swiPortEntry 1.3.6.1.4.1.207.8.4.4.4.87.1.1
An entry in the port information table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwiPortEntry  

swiPortNumber 1.3.6.1.4.1.207.8.4.4.4.87.1.1.1
This object identifies the port of the switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swiPortIngressLimit 1.3.6.1.4.1.207.8.4.4.4.87.1.1.20
The Ingress Bandwidth Limit applied to the port. A value of zero indicates that no limit is set.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

swiPortEgressLimit 1.3.6.1.4.1.207.8.4.4.4.87.1.1.21
The Egress Bandwidth Limit applied to the port. A value of zero indicates that no limit is set.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

swi56xxPortCounterTable 1.3.6.1.4.1.207.8.4.4.4.87.2
Table of swi56xx port counter properties.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Swi56xxPortCounterEntry

swi56xxPortCounterEntry 1.3.6.1.4.1.207.8.4.4.4.87.2.1
An entry in the port information table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Swi56xxPortCounterEntry  

swi56xxPortNumber 1.3.6.1.4.1.207.8.4.4.4.87.2.1.1
This object identifies the port of the switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swi56xxRxTx64kPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.2
The number of 64kB packets received and transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxRxTx65To127kPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.3
The number of 65kB To 127kB packets received and transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxRxTx128To255kPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.4
The number of 128kB To 255kB packets received and transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxRxTx256To511kPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.5
The number of 256kB To 511kB packets received and transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxRxTx512To1023kPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.6
The number of 512kB To 1023kB packets received and transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxRxTx1024ToMaxPktSzPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.7
The number of 1024kB To MaxPktSz packets received and transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxRxTx519To1522kPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.8
The number of 519kB To 1522kB packets received and transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxOctets 1.3.6.1.4.1.207.8.4.4.4.87.2.1.9
The number of octets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.10
The number of packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxFCSErrors 1.3.6.1.4.1.207.8.4.4.4.87.2.1.11
The number of frames received containing a Frame Check Sequence error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxMulticastPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.12
The number of multicast packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxBroadcastPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.13
The number of broadcast packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxPauseMACCtlFrms 1.3.6.1.4.1.207.8.4.4.4.87.2.1.14
The number of valid PAUSE MAC Control frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxOversizePkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.15
The number of oversize packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxFragments 1.3.6.1.4.1.207.8.4.4.4.87.2.1.16
The number of fragments received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxJabbers 1.3.6.1.4.1.207.8.4.4.4.87.2.1.17
The number of jabber frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxMACControlFrms 1.3.6.1.4.1.207.8.4.4.4.87.2.1.18
The number of MAC Control frames (Pause and Unsupported) received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxUnsupportOpcode 1.3.6.1.4.1.207.8.4.4.4.87.2.1.19
The number of MAC Control frames with unsupported opcode (i.e. not Pause) received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxAlignmentErrors 1.3.6.1.4.1.207.8.4.4.4.87.2.1.20
The number of frames with alignment errors received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxOutOfRngeLenFld 1.3.6.1.4.1.207.8.4.4.4.87.2.1.21
The number of packets with length out of range received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxSymErDurCarrier 1.3.6.1.4.1.207.8.4.4.4.87.2.1.22
The number of frames with invalid data symbols received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxCarrierSenseErr 1.3.6.1.4.1.207.8.4.4.4.87.2.1.23
The number of false carrier conditions between frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxUndersizePkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.24
The number of undersized packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortRxIpInHdrErrors 1.3.6.1.4.1.207.8.4.4.4.87.2.1.25
swiPortRxIpInHdrErrors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxOctets 1.3.6.1.4.1.207.8.4.4.4.87.2.1.26
The number of octets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.27
The number of packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxFCSErrors 1.3.6.1.4.1.207.8.4.4.4.87.2.1.28
The number of frames containing a Frame Check Sequence error transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxMulticastPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.29
The number of multicast packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxBroadcastPkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.30
The number of broadcast packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxPauseMACCtlFrms 1.3.6.1.4.1.207.8.4.4.4.87.2.1.31
The number of valid PAUSE MAC Control frames transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxOversizePkts 1.3.6.1.4.1.207.8.4.4.4.87.2.1.32
The number of oversize packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxFragments 1.3.6.1.4.1.207.8.4.4.4.87.2.1.33
The number of fragments transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxJabbers 1.3.6.1.4.1.207.8.4.4.4.87.2.1.34
The number of jabber frames transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxPauseCtrlFrms 1.3.6.1.4.1.207.8.4.4.4.87.2.1.35
The number of Pause control frames transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxFrameWDeferrdTx 1.3.6.1.4.1.207.8.4.4.4.87.2.1.36
The number of frames deferred once before successful transmission.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxFrmWExcesDefer 1.3.6.1.4.1.207.8.4.4.4.87.2.1.37
The number of frame aborted after too many deferrals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxSingleCollsnFrm 1.3.6.1.4.1.207.8.4.4.4.87.2.1.38
The number of frames which experienced exactly one collision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxMultCollsnFrm 1.3.6.1.4.1.207.8.4.4.4.87.2.1.39
The number of frames which experienced 2 to 15 collisions (including late collisions).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxLateCollsns 1.3.6.1.4.1.207.8.4.4.4.87.2.1.40
The number of frames which experienced late collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxExcessivCollsns 1.3.6.1.4.1.207.8.4.4.4.87.2.1.41
The number of frames aborted before transmission after 16 collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortTxCollisionFrames 1.3.6.1.4.1.207.8.4.4.4.87.2.1.42
The total number of collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortMiscDropEvents 1.3.6.1.4.1.207.8.4.4.4.87.2.1.43
The number of packets discarded at ingress port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortMiscTaggedPktTx 1.3.6.1.4.1.207.8.4.4.4.87.2.1.44
The number of VLAN tagged packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortMiscTotalPktTxAbort 1.3.6.1.4.1.207.8.4.4.4.87.2.1.45
The number of Layer 2 and 3 packets aborted during transmission.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortHWMultiTTLexpired 1.3.6.1.4.1.207.8.4.4.4.87.2.1.46
Number of multicast TTL expired frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortHWMultiBridgedFrames 1.3.6.1.4.1.207.8.4.4.4.87.2.1.47
Number of multicast bridged frames
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortHWMultiRxDrops 1.3.6.1.4.1.207.8.4.4.4.87.2.1.48
Number of multicast frames dropped at reception
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swi56xxPortHWMultiTxDrops 1.3.6.1.4.1.207.8.4.4.4.87.2.1.49
NNumber of multicast frames dropped at transmission
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swiDebugVariables 1.3.6.1.4.1.207.8.4.4.4.87.3
OBJECT IDENTIFIER    

swiDebugMemoryParityErrors 1.3.6.1.4.1.207.8.4.4.4.87.3.1
For switches based on certain switch chips, the number of parity errors that have been detected in packet memory associated with the switch. If the device does not include the counting of memory parity errors, this variable will return 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

swiIntrusionDetectionTrap 6
An intrusion detection trap is generated when a port has intrusion detection enabled, and the action taken when intrusion is detected is to generate a trap. Intrusion is detected when the number of MAC addresses learned on the port exceeds the configured learn limit. The ifIndex of the port is included in the trap.
TRAP-TYPE    

lb 1.3.6.1.4.1.207.8.4.4.4.104
OBJECT IDENTIFIER    

lbShowGlobalTable 1.3.6.1.4.1.207.8.4.4.4.104.1
General configuration and status of all of the virtual balancers configured on the router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LbShowGlobalEntry

lbShowGlobalEntry 1.3.6.1.4.1.207.8.4.4.4.104.1.1
An entry in the global table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LbShowGlobalEntry  

lbGlobalIndex 1.3.6.1.4.1.207.8.4.4.4.104.1.1.1
The index for the global table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbAffinityTimeOut 1.3.6.1.4.1.207.8.4.4.4.104.1.1.2
The length of time in seconds that a resource can be associated to a source IP address or Cookie after the connection has been closed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbOrphanTimeOut 1.3.6.1.4.1.207.8.4.4.4.104.1.1.3
The length of time in seconds that a connection can exist without having any data traversing it, before being declared an orphan and closed by the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbCriticalRst 1.3.6.1.4.1.207.8.4.4.4.104.1.1.4
The ratio of total messages received from a resource that can be TCP RST messages represented as a percentage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbTotalResources 1.3.6.1.4.1.207.8.4.4.4.104.1.1.5
The total number of resources configured on the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbTotalResPools 1.3.6.1.4.1.207.8.4.4.4.104.1.1.6
The total number of resource pools configured on the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbTotalVirtBals 1.3.6.1.4.1.207.8.4.4.4.104.1.1.7
The total number of virtual balancers configured on the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbCurrentConnections 1.3.6.1.4.1.207.8.4.4.4.104.1.1.8
Displays the current total number of connections to all resources in every resource pool on the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbShowResTable 1.3.6.1.4.1.207.8.4.4.4.104.2
A list about the general information about for a given resource.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LbShowResEntry

lbShowResEntry 1.3.6.1.4.1.207.8.4.4.4.104.2.1
An entry in the resource table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LbShowResEntry  

lbResIndex 1.3.6.1.4.1.207.8.4.4.4.104.2.1.1
The index for the resource table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbResource 1.3.6.1.4.1.207.8.4.4.4.104.2.1.2
The name of the resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbResIp 1.3.6.1.4.1.207.8.4.4.4.104.2.1.3
The IP address that a virtual balancer uses to accesses the resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

lbResPort 1.3.6.1.4.1.207.8.4.4.4.104.2.1.4
The port that the service that the resource offer is accessed on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbResState 1.3.6.1.4.1.207.8.4.4.4.104.2.1.5
The current state of the resource, either UP, DOWN, or CLOSING.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbResWeight 1.3.6.1.4.1.207.8.4.4.4.104.2.1.6
The weight that the virtual balancer will apply to the resource when selecting resources to try a connection to from a resource pool using either the WEIGHTEDLEASTCONNECT or WEIGHTEDLOTTERY selection algorithms.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbResTotalConnections 1.3.6.1.4.1.207.8.4.4.4.104.2.1.7
The total number of successful connections that have been made to this resource while it has been in the UP state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbResCurrentConnections 1.3.6.1.4.1.207.8.4.4.4.104.2.1.8
The total number of connections currently made to the resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbShowResPoolTable 1.3.6.1.4.1.207.8.4.4.4.104.3
A list about the general information about for a given resource pool.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LbShowResPoolEntry

lbShowResPoolEntry 1.3.6.1.4.1.207.8.4.4.4.104.3.1
An entry in the resource pool table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LbShowResPoolEntry  

lbResPoolIndex 1.3.6.1.4.1.207.8.4.4.4.104.3.1.1
The index for the resource pool table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbResPoolResourceIndex 1.3.6.1.4.1.207.8.4.4.4.104.3.1.2
The index for the resource table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbResPool 1.3.6.1.4.1.207.8.4.4.4.104.3.1.3
The name of the resource pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbResPoolSelectionAlg 1.3.6.1.4.1.207.8.4.4.4.104.3.1.4
The selection algorithm that ius employed by this resource pool when a resource has been selected for a connection. The options are ROUNDROBIN, WEIGHTEDLEASTCONNECT, WEIGHTEDLOTTERY and FASTESTRESPONSE.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbResPoolFailOnLast 1.3.6.1.4.1.207.8.4.4.4.104.3.1.5
Indicates whether or not the resource pool will fail a resource if it is the last resource in the resource pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbResPoolTotalConnections 1.3.6.1.4.1.207.8.4.4.4.104.3.1.6
The total number of successful connections that have been made to the resources in the resource pool over the lifetime of the resource pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbResPoolResources 1.3.6.1.4.1.207.8.4.4.4.104.3.1.7
The name of the resource that is currently allocated to the resource pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbShowVirtBalTable 1.3.6.1.4.1.207.8.4.4.4.104.4
A list about the general information about for a given virtual balancer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LbShowVirtBalEntry

lbShowVirtBalEntry 1.3.6.1.4.1.207.8.4.4.4.104.4.1
An entry in the virtual balancer table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LbShowVirtBalEntry  

lbVirtBalIndex 1.3.6.1.4.1.207.8.4.4.4.104.4.1.1
The index for the virtual balancer table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbVirtBal 1.3.6.1.4.1.207.8.4.4.4.104.4.1.2
The name of the virtual balancer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbVirtBalPublicIp 1.3.6.1.4.1.207.8.4.4.4.104.4.1.3
The IP address on which the virtual balancer will receive requests for the service provided by the resource pool associated with it.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

lbVirtBalPublicPort 1.3.6.1.4.1.207.8.4.4.4.104.4.1.4
The port on which the virtual balancer will receive requests for the service provided by the resource pool associated with it.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbVirtBalState 1.3.6.1.4.1.207.8.4.4.4.104.4.1.5
The current state of the virtual balancer, can either be UP, CLOSING, or DOWN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbVirtBalResPool 1.3.6.1.4.1.207.8.4.4.4.104.4.1.6
The name of the resource pool that is associated with the virtual balancer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbVirtBalType 1.3.6.1.4.1.207.8.4.4.4.104.4.1.7
The type of load balancer that this virtual balancer currently is, can be either TCP, HTTP, or ROUTE.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbVirtBalTotalConnections 1.3.6.1.4.1.207.8.4.4.4.104.4.1.8
The total number of stateful connections currently running through this virtual balancer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbVirtBalAffinity 1.3.6.1.4.1.207.8.4.4.4.104.4.1.9
Indicates whether or not entries will be made in a virtual balancers' affinity table for each stateful connection to a resource in its' resource pool (TCP and ROUTE type) or for cookies received from clients (HTTP type).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbVirtBalHttpErrorCode 1.3.6.1.4.1.207.8.4.4.4.104.4.1.10
A list of the HTTP server error status code added.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbShowAffTable 1.3.6.1.4.1.207.8.4.4.4.104.5
A list of affinity tables for all configured virtual balancers on the router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LbShowAffEntry

lbShowAffEntry 1.3.6.1.4.1.207.8.4.4.4.104.5.1
An entry in the affinity table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LbShowAffEntry  

lbAffIndex 1.3.6.1.4.1.207.8.4.4.4.104.5.1.1
The index for the affinity table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbAffVirtBal 1.3.6.1.4.1.207.8.4.4.4.104.5.1.2
The name of the virtual balancer whose affinity table is being displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbAffClientIp 1.3.6.1.4.1.207.8.4.4.4.104.5.1.3
The IP address that has affinity to the given resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

lbAffCookie 1.3.6.1.4.1.207.8.4.4.4.104.5.1.4
The cookie that has affinity to the given resource.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbAffResource 1.3.6.1.4.1.207.8.4.4.4.104.5.1.5
The name of the resource that the Client IP/Cookie has an affinity for.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbAffExpiry 1.3.6.1.4.1.207.8.4.4.4.104.5.1.6
The amount of seconds left before this entry expires, and is removed from the affinity table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbShowConTable 1.3.6.1.4.1.207.8.4.4.4.104.6
A list about all of the TCP connections currently open to a given virtual balancer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LbShowConEntry

lbShowConEntry 1.3.6.1.4.1.207.8.4.4.4.104.6.1
An entry in the connections table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LbShowConEntry  

lbConIndex 1.3.6.1.4.1.207.8.4.4.4.104.6.1.1
The index for the connections table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbConVirtBal 1.3.6.1.4.1.207.8.4.4.4.104.6.1.2
The name of the virtual balancer the listed connections are to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

lbConClientIp 1.3.6.1.4.1.207.8.4.4.4.104.6.1.3
The IP address of that originated the connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

lbConPort 1.3.6.1.4.1.207.8.4.4.4.104.6.1.4
The port on the originating system that represents the other end of the connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

lbConResource 1.3.6.1.4.1.207.8.4.4.4.104.6.1.5
The name of the resource that the connection has been made to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

ds3module 1.3.6.1.4.1.207.8.4.4.4.109
OBJECT IDENTIFIER    

ds3TrapTable 1.3.6.1.4.1.207.8.4.4.4.109.1
The ATR enterprise DS3 trap table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Ds3TrapEntry

ds3TrapEntry 1.3.6.1.4.1.207.8.4.4.4.109.1.1
An entry in the ATR enterprise DS3 trap table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Ds3TrapEntry  

ds3TcaTrapEnable 1.3.6.1.4.1.207.8.4.4.4.109.1.1.1
Indicates whether the threshold crossing alert traps should be generated for this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ds3TrapError 1.3.6.1.4.1.207.8.4.4.4.109.1.1.2
This variable shows which kind of parameter or primitive caused the trap. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The variable will hold the value at the latest trap. A value of ds3NoError shows no trap has occured
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds3NoError(1), ds3PES(2), ds3PSES(3), ds3SEFs(4), ds3UAS(5), ds3LCVs(6), ds3PCVs(7), ds3LESs(8), ds3CCVs(9), ds3CESs(10), ds3CSESs(11)  

ds3TrapLoc 1.3.6.1.4.1.207.8.4.4.4.109.1.1.3
This variable shows whether the trap was caused by a problem at the local or remote end. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The variable will hold the value at the latest trap. A value of ds3NoLoc shows no trap had occured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds3NoLoc(1), ds3Near(2), ds3Far(3)  

ds3TrapInterval 1.3.6.1.4.1.207.8.4.4.4.109.1.1.4
This variable shows whether the counter which has crossed the threshold is a twenty four hour or fifteen minute counter. This variable is really just a placeholder for the object sent in the DS3 TRAP, but can be read independently if required. The variable will hold the value at the latest trap. A value of ds3NoInt shows no trap has occured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds3NoInt(1), ds3Fifteen(2), ds3Twentyfour(3)  

tcaTrap 1
A DS3 trap is generated when a threshold crossing alert occurs. This happens when an error count exceeds a pre determined value. The values are counted over 15 minute and 24 hour periods. Once a trap has occured in a given period it may not occur again within the same period.
TRAP-TYPE