ALCATEL-IND1-TIMETRA-LDP-MIB

File: ALCATEL-IND1-TIMETRA-LDP-MIB.mib (252875 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
IF-MIB ALCATEL-IND1-TIMETRA-GLOBAL-MIB ALCATEL-IND1-TIMETRA-VRTR-MIB
ALCATEL-IND1-TIMETRA-TC-MIB MPLS-LDP-MIB ALCATEL-IND1-TIMETRA-SERV-MIB
ALCATEL-IND1-TIMETRA-FILTER-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Unsigned32 Counter32 Gauge32
IpAddress MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP RowStatus TruthValue
TestAndIncr TimeStamp TimeInterval
TEXTUAL-CONVENTION InterfaceIndexOrZero timetraSRMIBModules
tmnxSRObjs tmnxSRNotifyPrefix tmnxSRConfs
vRtrID vRtrLdpStatus TmnxAdminState
TmnxOperState TPolicyStatementNameOrEmpty TmnxServId
TmnxVcType TmnxVcId TNamedItemOrEmpty
TmnxVRtrMplsLspID MplsLdpIdentifier MplsLsrIdentifier
ServType SdpId TdmOptionsSigPkts
TdmOptionsCasTrunkFraming TFilterLogId TFilterID

Defined Types

TmnxLdpKeepAliveFactor  
TmnxLdpKeepAliveFactor specifies the value by which the keepalive timeout should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP Keepalive messages. LDP Keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors.
TEXTUAL-CONVENTION    
  Unsigned32 1..255  

TmnxLdpKeepAliveTimeout  
TmnxLdpKeepAliveTimeout specifies the the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the keepalive timeout interval should be configured to be 3 times the keepalive time (the time interval between successive LDP Keepalive messages).
TEXTUAL-CONVENTION    
  Unsigned32 1..65535  

TmnxLdpHelloFactor  
TmnxLdpHelloFactor specifies the value by which the hello timeout should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses Hello messages to discover neighbors and to detect loss of connectivity with its neighbors.
TEXTUAL-CONVENTION    
  Unsigned32 1..255  

TmnxLdpHelloTimeout  
TmnxLdpHelloTimeout specifies the the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the Hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time.
TEXTUAL-CONVENTION    
  Unsigned32 1..65535  

TmnxLdpBackoffTime  
TmnxLdpBackoffTime specifies the backoff interval (initial and maximum). The backoff interval is the time, in seconds, that LDP waits after an LDP session setup has failed before it attempts to setup the session again. After the LDP session startup fails the first time, the backoff interval is set to an initial value. Thereafter, if session startup fails again the backoff interval increases exponentially until it reaches a maximum value specified by the maximum backoff interval. If the maximum backoff interval is set to zero (0), then the backoff interval does not increase exponentially after the first session startup attempt fails. Instead it remains constant and LDP will keep retrying to establish a session until it succeeds.
TEXTUAL-CONVENTION    
  Unsigned32 0..2592000  

TmnxLdpFECPolicy  
TmnxLdpFECPolicy determines whether the LSR should generate FECs and which FECs it should generate. system(1) - LDP will distribute label bindings only for the router's system IP address interface(2) - LDP will distribute label bindings for all LDP interfaces all(3) - LDP will distribute label bindings for all prefixes in the routing table none(4) - LDP will not distribute any label bindings.
TEXTUAL-CONVENTION    
  INTEGER system(1), interface(2), all(3), none(4)  

TmnxLdpLabelDistMethod  
TmnxLdpLabelDistMethod describes the label distribution method used. When the value is 'downstreamOnDemand', label bindings are distributed to the upstream LSR only when a label request message is received. When the value is 'downstreamUnsolicited', label bindings are distributed to the upstream LSR, for each FEC, without requiring a request message for the FEC from the upstream LSR.
TEXTUAL-CONVENTION    
  INTEGER downstreamOnDemand(1), downstreamUnsolicited(2)  

TmnxLdpAdjacencyType  
TmnxLdpAdjacencyType describes the type of adjacency, either targeted or link, for a row in the vRtrLdpHelloAdjTable. It also describes the type of adjacencies in an LDP Session row in the vRtrLdpSessionTable.
TEXTUAL-CONVENTION    
  INTEGER link(1), targeted(2), both(3)  

TmnxVpnId  
TmnxVpnId specifies the value of a VPN (Virtual Private Network) identifier. This is a 10 byte value - the VPN 'type' is stored in the first two bytes the TmnxVpnId. The next four bytes store an 'AS (Autonomous System) number'. A 'local identifier' for the VPN is stored as the last four bytes.
TEXTUAL-CONVENTION    
  OCTET STRING Size(10)  

TmnxLabelStatus  
TmnxLabelStatus bit flags specifies the status of an ingress or egress label. Flags marked dummy* are not used and MUST be 0. 'statusSignalingSupported' - indicates whether status signaling is enabled or not. 'inUsePush' - indicates that the label contains valid information that is currently being used as a 'push' label. 'inUseSwap' - indicates that the label contains valid information that is currently being used as a 'swap' label. 'inUsePop' - indicates that the label contains valid information that is currently being used as a 'pop' label. 'released' - indicates that the label is in the process of being freed. With this flag set, no other flags will be set. 'notInUse' - indicates that the label contains valid information but is currently not being used possibly because the service is temporarily down. 'withdrawn' - indicates that the label has not been sent (possibly due to a mismatch in control word or status signaling) 'controlWord' - indicates that the control word will be signaled
TEXTUAL-CONVENTION    
  BITS dummyB0(0), dummyB1(1), statusSignalingSupported(2), inUsePush(3), inUseSwap(4), inUsePop(5), released(6), notInUse(7), withdrawn(8), controlWord(9)  

TmnxLabelSigStatus  
TmnxLabelSigStatus specifies the status of the pseudowire and attached circuit. The values are defined in draft-ietf-pwe3-iana-allocation-07.txt.
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxLdpFECType  
TmnxLdpFECType determines the kind of FEC that the label mapping, withdraw, release and request messages are referring to.
TEXTUAL-CONVENTION    
  INTEGER addrWildcard(1), addrPrefix(2), addrHost(3), vll(128), vpws(129), vpls(130)  

TmnxLdpFECFlags  
TmnxLdpFECFlags bit flags define the characteristics of FEC. Flags marked dummy* are not used and MUST be 0. Flag 'egress': this node is an egress for this FEC. Flag 'ingress': this node is a potential ingress for this FEC. Flag 'installedSwap': the label for this FEC has been programmed as a 'swap' label. Flag 'installedPush': the label for this FEC has been programmed as a 'push' label. Flag 'installedPop': the label for this FEC has been programmed as a 'pop' label. Flag 'local': this FEC is local to this node. Flag 'nextHop': the nextHop for this FEC is known. Flag 'vcSwitching': vcSwitching is enabled for the FEC. Flag 'importTargPolicyRejected': targeted LDP import policy has rejected this FEC. Flag 'exportTargPolicyRejected': targeted LDP export policy has rejected this FEC.
TEXTUAL-CONVENTION    
  BITS dummyB0(0), egress(1), ingress(2), installedSwap(3), installedPush(4), installedPop(5), local(6), nextHop(7), importPolicyRejected(8), exportPolicyAccepted(9), installedStaticFec(10), vcSwitching(11), importTargPolicyRejected(12), exportTargPolicyRejected(13)  

TmnxLdpGenOperDownReasonCode  
TmnxLdpGenOperDownReasonCode is an enumerated integer that specifies the reason that the LDP instance is operationally down.
TEXTUAL-CONVENTION    
  INTEGER operUp(0), adminDown(1), noListenSocket(2), noDiscoverySocket(3), noRtm(4), noTtm(5), iomFailure(6), recvFailure(7), clearDown(8), noResources(9), systemIpDown(10)  

TmnxLdpIntTargOperDownReasonCode  
TmnxLdpIntTargOperDownReasonCode is an enumerated integer that specifies the reason that the LDP interface and targeted peer is operationally down.
TEXTUAL-CONVENTION    
  INTEGER operUp(0), adminDown(1), noListenSocket(2), noDiscoverySocket(3), noResources(4), addrFecDeprogram(5), svcFecDeprogram(6), clearDown(7), instanceDown(8), interfaceDown(9), targetIpInvalid(10), interfaceInvalid(11)  

TmnxLdpFec129Tlv  
TmnxLdpFec129Tlv is a Type-Length-Value (Tlv) that specifies the value encoded as one-byte Type followed by one byte Length followed by the 'Length' size Value used for FEC-129 attribute.
TEXTUAL-CONVENTION    
  OCTET STRING Size(2..32)  

VRtrLdpGeneralEntry  
SEQUENCE    
  vRtrLdpGenLastChange TimeStamp
  vRtrLdpGenAdminState TmnxAdminState
  vRtrLdpGenOperState TmnxOperState
  vRtrLdpGenLdpLsrId MplsLsrIdentifier
  vRtrLdpGenProtocolVersion Unsigned32
  vRtrLdpGenDeaggregateFec TruthValue
  vRtrLdpGenKeepAliveFactor TmnxLdpKeepAliveFactor
  vRtrLdpGenKeepAliveTimeout TmnxLdpKeepAliveTimeout
  vRtrLdpGenHelloFactor TmnxLdpHelloFactor
  vRtrLdpGenHelloTimeout TmnxLdpHelloTimeout
  vRtrLdpGenRoutePreference Unsigned32
  vRtrLdpGenControlMode INTEGER
  vRtrLdpGenDistMethod TmnxLdpLabelDistMethod
  vRtrLdpGenRetentionMode INTEGER
  vRtrLdpGenTransportAddrType INTEGER
  vRtrLdpGenPropagatePolicy TmnxLdpFECPolicy
  vRtrLdpGenLoopDetectCapable INTEGER
  vRtrLdpGenHopLimit Unsigned32
  vRtrLdpGenPathVectorLimit Unsigned32
  vRtrLdpGenBackoffTime TmnxLdpBackoffTime
  vRtrLdpGenMaxBackoffTime TmnxLdpBackoffTime
  vRtrLdpGenTargKeepAliveFactor TmnxLdpKeepAliveFactor
  vRtrLdpGenTargKeepAliveTimeout TmnxLdpKeepAliveTimeout
  vRtrLdpGenTargHelloFactor TmnxLdpHelloFactor
  vRtrLdpGenTargHelloTimeout TmnxLdpHelloTimeout
  vRtrLdpGenTargPassiveMode TruthValue
  vRtrLdpGenTargetedSessions TruthValue
  vRtrLdpGenCreateTime TimeStamp
  vRtrLdpGenUpTime TimeInterval
  vRtrLdpGenImportPolicy1 TPolicyStatementNameOrEmpty
  vRtrLdpGenImportPolicy2 TPolicyStatementNameOrEmpty
  vRtrLdpGenImportPolicy3 TPolicyStatementNameOrEmpty
  vRtrLdpGenImportPolicy4 TPolicyStatementNameOrEmpty
  vRtrLdpGenImportPolicy5 TPolicyStatementNameOrEmpty
  vRtrLdpGenExportPolicy1 TPolicyStatementNameOrEmpty
  vRtrLdpGenExportPolicy2 TPolicyStatementNameOrEmpty
  vRtrLdpGenExportPolicy3 TPolicyStatementNameOrEmpty
  vRtrLdpGenExportPolicy4 TPolicyStatementNameOrEmpty
  vRtrLdpGenExportPolicy5 TPolicyStatementNameOrEmpty
  vRtrLdpGenTunnelDownDampTime Unsigned32
  vRtrLdpGenOperDownReason TmnxLdpGenOperDownReasonCode
  vRtrLdpGenTrustList TFilterID
  vRtrLdpGenGracefulRestart TruthValue
  vRtrLdpGenGRNbrLiveTime Unsigned32
  vRtrLdpGenGRMaxRecoveryTime Unsigned32

VRtrLdpStatsEntry  
SEQUENCE    
  vRtrLdpStatsOperDownEvents Counter32
  vRtrLdpStatsActiveSessions Gauge32
  vRtrLdpStatsActiveAdjacencies Gauge32
  vRtrLdpStatsActiveInterfaces Gauge32
  vRtrLdpStatsInactiveInterfaces Gauge32
  vRtrLdpStatsActiveTargSessions Gauge32
  vRtrLdpStatsInactiveTargSessions Gauge32
  vRtrLdpStatsAddrFECRecv Gauge32
  vRtrLdpStatsAddrFECSent Gauge32
  vRtrLdpStatsSvcFECRecv Gauge32
  vRtrLdpStatsSvcFECSent Gauge32
  vRtrLdpStatsAttemptedSessions Counter32
  vRtrLdpStatsSessRejNoHelloErrors Counter32
  vRtrLdpStatsSessRejAdvErrors Counter32
  vRtrLdpStatsSessRejMaxPduErrors Counter32
  vRtrLdpStatsSessRejLabelRangeErrors Counter32
  vRtrLdpStatsBadLdpIdentifierErrors Counter32
  vRtrLdpStatsBadPduLengthErrors Counter32
  vRtrLdpStatsBadMessageLengthErrors Counter32
  vRtrLdpStatsBadTlvLengthErrors Counter32
  vRtrLdpStatsMalformedTlvValueErrors Counter32
  vRtrLdpStatsKeepAliveExpiredErrors Counter32
  vRtrLdpStatsShutdownNotifRecv Counter32
  vRtrLdpStatsShutdownNotifSent Counter32

VRtrLdpPolicyEntry  
SEQUENCE    
  vRtrLdpPolicyType INTEGER
  vRtrLdpPolicyIndex Unsigned32
  vRtrLdpPolicyRowStatus RowStatus
  vRtrLdpPolicyName TPolicyStatementNameOrEmpty

VRtrLdpIfEntry  
SEQUENCE    
  vRtrLdpIfIndex InterfaceIndexOrZero
  vRtrLdpPeerAddress IpAddress
  vRtrLdpIfRowStatus RowStatus
  vRtrLdpIfLastChange TimeStamp
  vRtrLdpIfAdminState TmnxAdminState
  vRtrLdpIfOperState TmnxOperState
  vRtrLdpIfInheritance Unsigned32
  vRtrLdpIfKeepAliveFactor TmnxLdpKeepAliveFactor
  vRtrLdpIfKeepAliveTimeout TmnxLdpKeepAliveTimeout
  vRtrLdpIfHelloFactor TmnxLdpHelloFactor
  vRtrLdpIfHelloTimeout TmnxLdpHelloTimeout
  vRtrLdpIfBackoffTime TmnxLdpBackoffTime
  vRtrLdpIfMaxBackoffTime TmnxLdpBackoffTime
  vRtrLdpIfTransportAddrType INTEGER
  vRtrLdpIfPassiveMode TruthValue
  vRtrLdpIfAutoCreate TruthValue
  vRtrLdpIfOperDownReason TmnxLdpIntTargOperDownReasonCode
  vRtrLdpIfTunneling TruthValue

VRtrLdpIfStatsEntry  
SEQUENCE    
  vRtrLdpIfExistingAdjacencies Gauge32

VRtrLdpHelloAdjEntry  
SEQUENCE    
  vRtrLdpPeerLdpId MplsLdpIdentifier
  vRtrLdpHelloAdjLocalLdpId MplsLdpIdentifier
  vRtrLdpHelloAdjEntityIndex Unsigned32
  vRtrLdpHelloAdjIndex Unsigned32
  vRtrLdpHelloAdjHoldTimeRemaining Unsigned32
  vRtrLdpHelloAdjType TmnxLdpAdjacencyType
  vRtrLdpHelloAdjRemoteConfSeqNum Unsigned32
  vRtrLdpHelloAdjRemoteIpAddress IpAddress
  vRtrLdpHelloAdjUpTime TimeInterval
  vRtrLdpHelloAdjLocalConfSeqNum Unsigned32
  vRtrLdpHelloAdjLocalIpAddress IpAddress
  vRtrLdpHelloAdjInHelloMsgCount Counter32
  vRtrLdpHelloAdjOutHelloMsgCount Counter32
  vRtrLdpHelloAdjLocalHelloTimeout TmnxLdpHelloTimeout
  vRtrLdpHelloAdjRemoteHelloTimeout TmnxLdpHelloTimeout

VRtrLdpHelloAdjMapEntry  
SEQUENCE    
  vRtrLdpHelloAdjMapLdpId MplsLdpIdentifier

VRtrLdpSessionEntry  
SEQUENCE    
  vRtrLdpSessLocalLdpId MplsLdpIdentifier
  vRtrLdpSessEntityIndex Unsigned32
  vRtrLdpSessLabelDistMethod TmnxLdpLabelDistMethod
  vRtrLdpSessLoopDetectForPV INTEGER
  vRtrLdpSessPathVectorLimit Unsigned32
  vRtrLdpSessState INTEGER
  vRtrLdpSessAdjacencyType TmnxLdpAdjacencyType
  vRtrLdpSessProtocolVersion Unsigned32
  vRtrLdpSessLocalUdpPort Unsigned32
  vRtrLdpSessPeerUdpPort Unsigned32
  vRtrLdpSessLocalTcpPort Unsigned32
  vRtrLdpSessPeerTcpPort Unsigned32
  vRtrLdpSessLocalAddress IpAddress
  vRtrLdpSessPeerAddress IpAddress
  vRtrLdpSessKAHoldTimeRemaining TimeInterval
  vRtrLdpSessMaxPduLength Unsigned32
  vRtrLdpSessUpTime TimeInterval
  vRtrLdpSessLocalKATimeout TmnxLdpKeepAliveTimeout
  vRtrLdpSessPeerKATimeout TmnxLdpKeepAliveTimeout
  vRtrLdpSessAdvertise INTEGER
  vRtrLdpSessRestartHelperState TruthValue
  vRtrLdpSessPeerNumRestart Counter32
  vRtrLdpSessLastRestartTime TimeStamp
  vRtrLdpSessFtReconnectTimeNego Unsigned32
  vRtrLdpSessFtRecoveryTimeNego Unsigned32
  vRtrLdpSessFtReconTimeRemaining Unsigned32
  vRtrLdpSessFtRecovTimeRemaining Unsigned32

VRtrLdpSessionStatsEntry  
SEQUENCE    
  vRtrLdpSessStatsTargAdj Gauge32
  vRtrLdpSessStatsLinkAdj Gauge32
  vRtrLdpSessStatsFECRecv Counter32
  vRtrLdpSessStatsFECSent Counter32
  vRtrLdpSessStatsHelloIn Counter32
  vRtrLdpSessStatsHelloOut Counter32
  vRtrLdpSessStatsKeepaliveIn Counter32
  vRtrLdpSessStatsKeepaliveOut Counter32
  vRtrLdpSessStatsInitIn Counter32
  vRtrLdpSessStatsInitOut Counter32
  vRtrLdpSessStatsLabelMappingIn Counter32
  vRtrLdpSessStatsLabelMappingOut Counter32
  vRtrLdpSessStatsLabelRequestIn Counter32
  vRtrLdpSessStatsLabelRequestOut Counter32
  vRtrLdpSessStatsLabelReleaseIn Counter32
  vRtrLdpSessStatsLabelReleaseOut Counter32
  vRtrLdpSessStatsLabelWithdrawIn Counter32
  vRtrLdpSessStatsLabelWithdrawOut Counter32
  vRtrLdpSessStatsLabelAbortIn Counter32
  vRtrLdpSessStatsLabelAbortOut Counter32
  vRtrLdpSessStatsAddrIn Counter32
  vRtrLdpSessStatsAddrOut Counter32
  vRtrLdpSessStatsAddrWithdrawIn Counter32
  vRtrLdpSessStatsAddrWithdrawOut Counter32
  vRtrLdpSessStatsNotificationIn Counter32
  vRtrLdpSessStatsNotificationOut Counter32

VRtrLdpServFecEntry  
SEQUENCE    
  vRtrLdpServFecFecType TmnxLdpFECType
  vRtrLdpServFecVcType TmnxVcType
  vRtrLdpServFecVcId TmnxVcId
  vRtrLdpServFecServType ServType
  vRtrLdpServFecServId TmnxServId
  vRtrLdpServFecVpnId TmnxVpnId
  vRtrLdpServFecFlags TmnxLdpFECFlags
  vRtrLdpServFecNumInLabels Unsigned32
  vRtrLdpServFecNumOutLabels Unsigned32
  vRtrLdpServFecInLabel1 Unsigned32
  vRtrLdpServFecInLabelStatus1 TmnxLabelStatus
  vRtrLdpServFecInLabel2 Unsigned32
  vRtrLdpServFecInLabelStatus2 TmnxLabelStatus
  vRtrLdpServFecInLabel3 Unsigned32
  vRtrLdpServFecInLabelStatus3 TmnxLabelStatus
  vRtrLdpServFecInLabel4 Unsigned32
  vRtrLdpServFecInLabelStatus4 TmnxLabelStatus
  vRtrLdpServFecInLabel5 Unsigned32
  vRtrLdpServFecInLabelStatus5 TmnxLabelStatus
  vRtrLdpServFecOutLabel1 Unsigned32
  vRtrLdpServFecOutLabelStatus1 TmnxLabelStatus
  vRtrLdpServFecOutLabel2 Unsigned32
  vRtrLdpServFecOutLabelStatus2 TmnxLabelStatus
  vRtrLdpServFecOutLabel3 Unsigned32
  vRtrLdpServFecOutLabelStatus3 TmnxLabelStatus
  vRtrLdpServFecOutLabel4 Unsigned32
  vRtrLdpServFecOutLabelStatus4 TmnxLabelStatus
  vRtrLdpServFecOutLabel5 Unsigned32
  vRtrLdpServFecOutLabelStatus5 TmnxLabelStatus
  vRtrLdpServFecSdpId SdpId
  vRtrLdpServFecLocalMTU Unsigned32
  vRtrLdpServFecRemoteMTU Unsigned32
  vRtrLdpServFecLocalVlanTag Unsigned32
  vRtrLdpServFecRemoteVlanTag Unsigned32
  vRtrLdpServFecLocalMaxCellConcat Unsigned32
  vRtrLdpServFecRemoteMaxCellConcat Unsigned32
  vRtrLdpServFecInLabelSigStatus1 TmnxLabelSigStatus
  vRtrLdpServFecInLabelSigStatus2 TmnxLabelSigStatus
  vRtrLdpServFecInLabelSigStatus3 TmnxLabelSigStatus
  vRtrLdpServFecInLabelSigStatus4 TmnxLabelSigStatus
  vRtrLdpServFecInLabelSigStatus5 TmnxLabelSigStatus
  vRtrLdpServFecOutLabelSigStatus1 TmnxLabelSigStatus
  vRtrLdpServFecOutLabelSigStatus2 TmnxLabelSigStatus
  vRtrLdpServFecOutLabelSigStatus3 TmnxLabelSigStatus
  vRtrLdpServFecOutLabelSigStatus4 TmnxLabelSigStatus
  vRtrLdpServFecOutLabelSigStatus5 TmnxLabelSigStatus
  vRtrLdpServFecMateEndpointVcId TmnxVcId
  vRtrLdpServFecMateEndpointSdpId SdpId

VRtrLdpServFecMapEntry  
SEQUENCE    
  vRtrLdpServFecMapFecType TmnxLdpFECType
  vRtrLdpServFecMapVcType TmnxVcType
  vRtrLdpServFecMapVcId TmnxVcId

VRtrLdpAddrFecEntry  
SEQUENCE    
  vRtrLdpAddrFecFecType TmnxLdpFECType
  vRtrLdpAddrFecIpPrefix IpAddress
  vRtrLdpAddrFecIpMask IpAddress
  vRtrLdpAddrFecFlags TmnxLdpFECFlags
  vRtrLdpAddrFecNumInLabels Unsigned32
  vRtrLdpAddrFecNumOutLabels Unsigned32
  vRtrLdpAddrFecInLabel1 Unsigned32
  vRtrLdpAddrFecInLabelStatus1 TmnxLabelStatus
  vRtrLdpAddrFecInLabelIfIndex1 InterfaceIndexOrZero
  vRtrLdpAddrFecInLabel2 Unsigned32
  vRtrLdpAddrFecInLabelStatus2 TmnxLabelStatus
  vRtrLdpAddrFecInLabelIfIndex2 InterfaceIndexOrZero
  vRtrLdpAddrFecInLabel3 Unsigned32
  vRtrLdpAddrFecInLabelStatus3 TmnxLabelStatus
  vRtrLdpAddrFecInLabelIfIndex3 InterfaceIndexOrZero
  vRtrLdpAddrFecInLabel4 Unsigned32
  vRtrLdpAddrFecInLabelStatus4 TmnxLabelStatus
  vRtrLdpAddrFecInLabelIfIndex4 InterfaceIndexOrZero
  vRtrLdpAddrFecInLabel5 Unsigned32
  vRtrLdpAddrFecInLabelStatus5 TmnxLabelStatus
  vRtrLdpAddrFecInLabelIfIndex5 InterfaceIndexOrZero
  vRtrLdpAddrFecOutLabel1 Unsigned32
  vRtrLdpAddrFecOutLabelStatus1 TmnxLabelStatus
  vRtrLdpAddrFecOutLabelIfIndex1 InterfaceIndexOrZero
  vRtrLdpAddrFecOutLabelNextHop1 IpAddress
  vRtrLdpAddrFecOutLabel2 Unsigned32
  vRtrLdpAddrFecOutLabelStatus2 TmnxLabelStatus
  vRtrLdpAddrFecOutLabelIfIndex2 InterfaceIndexOrZero
  vRtrLdpAddrFecOutLabelNextHop2 IpAddress
  vRtrLdpAddrFecOutLabel3 Unsigned32
  vRtrLdpAddrFecOutLabelStatus3 TmnxLabelStatus
  vRtrLdpAddrFecOutLabelIfIndex3 InterfaceIndexOrZero
  vRtrLdpAddrFecOutLabelNextHop3 IpAddress
  vRtrLdpAddrFecOutLabel4 Unsigned32
  vRtrLdpAddrFecOutLabelStatus4 TmnxLabelStatus
  vRtrLdpAddrFecOutLabelIfIndex4 InterfaceIndexOrZero
  vRtrLdpAddrFecOutLabelNextHop4 IpAddress
  vRtrLdpAddrFecOutLabel5 Unsigned32
  vRtrLdpAddrFecOutLabelStatus5 TmnxLabelStatus
  vRtrLdpAddrFecOutLabelIfIndex5 InterfaceIndexOrZero
  vRtrLdpAddrFecOutLabelNextHop5 IpAddress
  vRtrLdpAddrFecLspId TmnxVRtrMplsLspID

VRtrLdpAddrFecMapEntry  
SEQUENCE    
  vRtrLdpAddrFecMapFecType TmnxLdpFECType
  vRtrLdpAddrFecMapIpPrefix IpAddress
  vRtrLdpAddrFecMapIpMask IpAddress

VRtrLdpAdjBackoffEntry  
SEQUENCE    
  vRtrLdpAdjInitBackoff Unsigned32
  vRtrLdpAdjMaxBackoff Unsigned32
  vRtrLdpAdjCurrentBackoff Unsigned32
  vRtrLdpAdjWaitingTime Unsigned32
  vRtrLdpAdjBackoffStatus TruthValue

VRtrLdpPeerParamsEntry  
SEQUENCE    
  vRtrLdpPeerRowStatus RowStatus
  vRtrLdpPeerAuth TruthValue
  vRtrLdpPeerAuthKey OCTET STRING
  vRtrLdpPeerMinTTLValue Unsigned32
  vRtrLdpPeerTTLLogId TFilterLogId
  vRtrLdpPeerAuthKeyChain TNamedItemOrEmpty

VRtrLdpStaticFecEntry  
SEQUENCE    
  vRtrLdpStaticFecIpPrefix IpAddress
  vRtrLdpStaticFecIpMask IpAddress
  vRtrLdpStaticFecRowStatus RowStatus
  vRtrLdpStaticFecNextNHIndex Unsigned32
  vRtrLdpStaticFecIngLabel Unsigned32
  vRtrLdpStaticFecNumNH Gauge32
  vRtrLdpStaticFecOperIngLabel Unsigned32

VRtrLdpStaticFecNHEntry  
SEQUENCE    
  vRtrLdpStaticFecNHIndex Unsigned32
  vRtrLdpStaticFecNHRowStatus RowStatus
  vRtrLdpStaticFecNHType INTEGER
  vRtrLdpStaticFecNHIpAddr IpAddress
  vRtrLdpStaticFecNHEgrLabel Unsigned32

VRtrLdpTargEntry  
SEQUENCE    
  vRtrLdpTargImportPolicy1 TPolicyStatementNameOrEmpty
  vRtrLdpTargImportPolicy2 TPolicyStatementNameOrEmpty
  vRtrLdpTargImportPolicy3 TPolicyStatementNameOrEmpty
  vRtrLdpTargImportPolicy4 TPolicyStatementNameOrEmpty
  vRtrLdpTargImportPolicy5 TPolicyStatementNameOrEmpty
  vRtrLdpTargExportPolicy1 TPolicyStatementNameOrEmpty
  vRtrLdpTargExportPolicy2 TPolicyStatementNameOrEmpty
  vRtrLdpTargExportPolicy3 TPolicyStatementNameOrEmpty
  vRtrLdpTargExportPolicy4 TPolicyStatementNameOrEmpty
  vRtrLdpTargExportPolicy5 TPolicyStatementNameOrEmpty
  vRtrLdpTargTunnelPreference TruthValue

VRtrLdpIfTunnelingLspEntry  
SEQUENCE    
  vRtrLdpIfLspId TmnxVRtrMplsLspID
  vRtrLdpIfLspRowStatus RowStatus

VRtrLdpCepTdmFecEntry  
SEQUENCE    
  vRtrLdpCepTdmLocalPayloadSize Unsigned32
  vRtrLdpCepTdmRemotePayloadSize Unsigned32
  vRtrLdpCepTdmLocalBitrate Unsigned32
  vRtrLdpCepTdmRemoteBitrate Unsigned32
  vRtrLdpCepTdmLocalRtpHeader TruthValue
  vRtrLdpCepTdmRemoteRtpHeader TruthValue
  vRtrLdpCepTdmLocalDiffTimestamp TruthValue
  vRtrLdpCepTdmRemoteDiffTimestamp TruthValue
  vRtrLdpCepTdmLocalSigPkts TdmOptionsSigPkts
  vRtrLdpCepTdmRemoteSigPkts TdmOptionsSigPkts
  vRtrLdpCepTdmLocalCasTrunk TdmOptionsCasTrunkFraming
  vRtrLdpCepTdmRemoteCasTrunk TdmOptionsCasTrunkFraming
  vRtrLdpCepTdmLocalTimestampFreq Unsigned32
  vRtrLdpCepTdmRemoteTimestampFreq Unsigned32
  vRtrLdpCepTdmLocalPayloadType Unsigned32
  vRtrLdpCepTdmRemotePayloadType Unsigned32
  vRtrLdpCepTdmLocalSsrcId Unsigned32
  vRtrLdpCepTdmRemoteSsrcId Unsigned32

VLdpServFec129Entry  
SEQUENCE    
  vLdpServFec129AgiTlv TmnxLdpFec129Tlv
  vLdpServFec129SrcAiiTlv TmnxLdpFec129Tlv
  vLdpServFec129TgtAiiTlv TmnxLdpFec129Tlv
  vLdpServFec129ServType ServType
  vLdpServFec129ServId TmnxServId
  vLdpServFec129VpnId TmnxVpnId
  vLdpServFec129Flags TmnxLdpFECFlags
  vLdpServFec129NumInLabels Unsigned32
  vLdpServFec129NumOutLabels Unsigned32
  vLdpServFec129InLabel1 Unsigned32
  vLdpServFec129InLabelStatus1 TmnxLabelStatus
  vLdpServFec129OutLabel1 Unsigned32
  vLdpServFec129OutLabelStatus1 TmnxLabelStatus
  vLdpServFec129SdpId SdpId
  vLdpServFec129LocalMTU Unsigned32
  vLdpServFec129RemoteMTU Unsigned32
  vLdpServFec129LocalVlanTag Unsigned32
  vLdpServFec129RemoteVlanTag Unsigned32
  vLdpServFec129LocalMaxCellConcat Unsigned32
  vLdpServFec129RemoteMaxCellConcat Unsigned32
  vLdpServFec129InLabelSigStatus1 TmnxLabelSigStatus
  vLdpServFec129OutLabelSigStatus1 TmnxLabelSigStatus

VLdpServFec129MapEntry  
SEQUENCE    
  vLdpServFec129MapVcType TmnxVcType
  vLdpServFec129MapAgiTlv TmnxLdpFec129Tlv
  vLdpServFec129MapSrcAiiTlv TmnxLdpFec129Tlv
  vLdpServFec129MapTgtAiiTlv TmnxLdpFec129Tlv

VLdpCepTdmFec129Entry  
SEQUENCE    
  vLdpCepTdmFec129LocalPayloadSize Unsigned32
  vLdpCepTdmFec129RemotePayloadSize Unsigned32
  vLdpCepTdmFec129LocalBitrate Unsigned32
  vLdpCepTdmFec129RemoteBitrate Unsigned32
  vLdpCepTdmFec129LocalRtpHeader TruthValue
  vLdpCepTdmFec129RemoteRtpHeader TruthValue
  vLdpCepTdmFec129LocalDiffTimestamp TruthValue
  vLdpCepTdmFec129RemoteDiffTimestamp TruthValue
  vLdpCepTdmFec129LocalSigPkts TdmOptionsSigPkts
  vLdpCepTdmFec129RemoteSigPkts TdmOptionsSigPkts
  vLdpCepTdmFec129LocalCasTrunk TdmOptionsCasTrunkFraming
  vLdpCepTdmFec129RemoteCasTrunk TdmOptionsCasTrunkFraming
  vLdpCepTdmFec129LocalTimestampFreq Unsigned32
  vLdpCepTdmFec129RemoteTimestampFreq Unsigned32
  vLdpCepTdmFec129LocalPayloadType Unsigned32
  vLdpCepTdmFec129RemotePayloadType Unsigned32
  vLdpCepTdmFec129LocalSsrcId Unsigned32
  vLdpCepTdmFec129RemoteSsrcId Unsigned32

Defined Values

timetraLdpMIBModule 1.3.6.1.4.1.6527.1.1.3.8
The MIB module to manage and provision the Alcatel 7x50 LDP protocol features. Copyright 2003-2008 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel's proprietary intellectual property. Alcatel retains all title and ownership in the Specification, including any revisions. Alcatel grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY    

tmnxLdpObjs 1.3.6.1.4.1.6527.3.1.2.8
OBJECT IDENTIFIER    

tmnxLdpConformance 1.3.6.1.4.1.6527.3.1.1.8
OBJECT IDENTIFIER    

tmnxLdpNotifyPrefix 1.3.6.1.4.1.6527.3.1.3.8
OBJECT IDENTIFIER    

tmnxLdpNotifications 1.3.6.1.4.1.6527.3.1.3.8.0
OBJECT IDENTIFIER    

vRtrLdpGeneralTable 1.3.6.1.4.1.6527.3.1.2.8.1
vRtrLdpGeneralTable has an entry for each virtual router in the system capable of supporting an instance of the Label Distribution Protocol (LDP).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpGeneralEntry

vRtrLdpGeneralEntry 1.3.6.1.4.1.6527.3.1.2.8.1.1
Each row entry represents an instance of the Label Distribution Protocol (LDP) for a virtual router in the system. An entry in this table is created by the agent when vRtrLdpStatus in the vRtrConfTable is set to 'create'. The entry is destroyed when vRtrLdpStatus is set to 'delete' but only if vRtrLdpGenAdminState has a value of 'outOfService'.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpGeneralEntry  

vRtrLdpGenLastChange 1.3.6.1.4.1.6527.3.1.2.8.1.1.1
The value of vRtrLdpGenLastChange specifies the sysUpTime when this row was last modified.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vRtrLdpGenAdminState 1.3.6.1.4.1.6527.3.1.2.8.1.1.2
The value of vRtrLdpGenAdminState specifies the desired administrative state for this LDP instance.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAdminState  

vRtrLdpGenOperState 1.3.6.1.4.1.6527.3.1.2.8.1.1.3
The value of vRtrLdpGenOperState specifies the current operational state of this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOperState  

vRtrLdpGenLdpLsrId 1.3.6.1.4.1.6527.3.1.2.8.1.1.4
The value of vRtrLdpGenLdpLsrId is the Label Switch Router (LSR) identifier which is used as the first 4 bytes or the Router Id component of the Label Distribution Protocol (LDP) identifier.
Status: current Access: read-only
OBJECT-TYPE    
  MplsLsrIdentifier  

vRtrLdpGenProtocolVersion 1.3.6.1.4.1.6527.3.1.2.8.1.1.5
The value of vRtrLdpGenProtocolVersion specifies the version of the LDP protocol instance. A value of zero (0) indicates that the version of the protocol is unknown.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpGenDeaggregateFec 1.3.6.1.4.1.6527.3.1.2.8.1.1.6
When vRtrLdpGenDeaggregateFec has a value of 'false', LDP aggregates multiple prefixes into a single Forwarding Equivalence Class (FEC) and advertises a single label for the FEC. When the value is 'true', LDP deaggregates prefixes into multiple FECs. This value is only applicable to LDP interfaces and not for targeted sessions.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vRtrLdpGenKeepAliveFactor 1.3.6.1.4.1.6527.3.1.2.8.1.1.7
The value of vRtrLdpGenKeepAliveFactor specifies the value by which the keepalive timeout (vRtrLdpGenKeepAliveTimeout) should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors. This value is only applicable to LDP interfaces and not for targeted sessions.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpKeepAliveFactor  

vRtrLdpGenKeepAliveTimeout 1.3.6.1.4.1.6527.3.1.2.8.1.1.8
The value of vRtrLdpGenKeepAliveTimeout specifies the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value of vRtrLdpGenKeepAliveTimeout is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages). This value is only applicable to LDP interfaces and not for targeted sessions.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpKeepAliveTimeout  

vRtrLdpGenHelloFactor 1.3.6.1.4.1.6527.3.1.2.8.1.1.9
The value of vRtrLdpGenHelloFactor specifies the value by which the hello timeout (vRtrLdpGenHelloTimeout) should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. This value is only applicable to LDP interfaces and not for targeted sessions.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpHelloFactor  

vRtrLdpGenHelloTimeout 1.3.6.1.4.1.6527.3.1.2.8.1.1.10
The value of vRtrLdpGenHelloTimeout specifies the hello time also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time. This value is only applicable to LDP interfaces and not for targeted sessions.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpHelloTimeout  

vRtrLdpGenRoutePreference 1.3.6.1.4.1.6527.3.1.2.8.1.1.11
The value of vRtrLdpGenRoutePreference specifies the route preference assigned to LDP routes. When multiple routes are available to a destination, the route with the lowest preference will be used. This value is only applicable to LDP interfaces and not for targeted sessions.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..255  

vRtrLdpGenControlMode 1.3.6.1.4.1.6527.3.1.2.8.1.1.12
The value of vRtrLdpGenControlMode specifies the mode used for distributing labels in response to label binding requests. When vRtrLdpGenControlMode has a value of 'ordered', label bindings are not distributed in response to a label request until a label binding has been received from the next hop for the destination. When vRtrLdpGenControlMode has a value of 'independent', label bindings are distributed immediately in response to a label request even if a label binding has not yet been received from the next hop for the destination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ordered(1), independent(2)  

vRtrLdpGenDistMethod 1.3.6.1.4.1.6527.3.1.2.8.1.1.13
The value of vRtrLdpGenDistMethod specifies the label distribution method used. When vRtrLdpGenDistMethod has a value of 'downstreamOnDemand', label bindings are distributed to the upstream LSR, for each FEC, without requiring a request message for the FEC from the upstream LSR. When vRtrLdpGenDistMethod has a value of 'downstreamUnsolicited', label bindings are distributed to the upstream LSR only when a label request message is received.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpLabelDistMethod  

vRtrLdpGenRetentionMode 1.3.6.1.4.1.6527.3.1.2.8.1.1.14
The value of vRtrLdpGenRetentionMode specifies the label retention mode used. If the value of this object is 'conservative', then advertized label mappings are retained only if they will be used to forward packets, i.e. if the label came from a valid next hop. Label bindings received from non-nexthops for each FEC are discarded. If the value of this object is 'liberal', then all advertized label mappings are retained whether they are from a valid next hop or not. When vRtrLdpGenDistMethod has a value of 'downstreamUnsolicited', a LSR may receive label bindings for the same destination for all its neighbors. Labels for the non-nexthops for the FECs are retained in the software but not used. When a network topology change occurs where a non-nexthop becomes a true next hop, the label received earlier is then used.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER conservative(1), liberal(2)  

vRtrLdpGenTransportAddrType 1.3.6.1.4.1.6527.3.1.2.8.1.1.15
The value of vRtrLdpGenTransportAddrType specifies the source of the transport address to be used when setting up the LDP TCP sessions. The transport address can be configured globally (applied to all interfaces) or per interface. When the value of this object is 'interface', the interface's IP address is used to setup the LDP session between neighbors. If multiple interfaces exist between two neighbors, the 'interface' mode cannot be used since only one LDP session is actually set up between the two neighbors. When the value of this object is 'system', the system's IP address is used to set up the LDP session between neighbors. This value is only applicable to LDP interfaces and not for targeted sessions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER interface(1), system(2)  

vRtrLdpGenPropagatePolicy 1.3.6.1.4.1.6527.3.1.2.8.1.1.16
The value of vRtrLdpGenPropagatePolicy determines whether the LSR should generate FECs and which FECs it should generate. When the value of this object is 'system', LDP will distribute label bindings only for the router's system IP address When the value of this object is 'interface', LDP will distribute label bindings for all LDP interfaces When the value of this object is 'all', LDP will distribute label bindings for all prefixes in the routing table When the value of this object is 'none', LDP will not distribute any label bindings. This value is only applicable to LDP interfaces and not for targeted sessions.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpFECPolicy  

vRtrLdpGenLoopDetectCapable 1.3.6.1.4.1.6527.3.1.2.8.1.1.17
The value of vRtrLdpGenLoopDetectCapable indicate whether this LSR supports loop detection and if so, what type of loop detection is supported. When the value is 'none' loop detection is not supported on this LSR. When the value is 'other' Loop Detection is supported but by a method other than those listed below. When the value is 'hopCount' Loop Detection is supported by Hop Count only. When the value is 'pathVector' Loop Detection is supported by Path Vector only. When the value is 'hopCountAndPathVector' Loop Detection is supported by both Hop Count and Path Vector. Since Loop Detection is determined during Session Initialization, an individual session may not be running with loop detection. This object simply gives an indication of whether or not the LSR has the ability to support Loop Detection and which types.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), other(2), hopCount(3), pathVector(4), hopCountAndPathVector(5)  

vRtrLdpGenHopLimit 1.3.6.1.4.1.6527.3.1.2.8.1.1.18
The value of vRtrLdpGenHopLimit specifies the maximum allowable value for the hop count. The value of this object is valid and used only if vRtrLdpGenLoopDetectCapable has a value of either 'hopCount' or 'hopCountAndPathVector'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

vRtrLdpGenPathVectorLimit 1.3.6.1.4.1.6527.3.1.2.8.1.1.19
The value of vRtrLdpGenPathVectorLimit specifies the maximum allowable value for the path vector count. The value of this object is valid and used only if vRtrLdpGenLoopDetectCapable has a value of either 'pathVector' or 'hopCountAndPathVector'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

vRtrLdpGenBackoffTime 1.3.6.1.4.1.6527.3.1.2.8.1.1.20
The value of vRtrLdpGenBackoffTime specifies the initial value for the backoff interval. The backoff interval is the time, in seconds, that LDP waits after an LDP session setup has failed before it attempts to setup the session again. After the LDP session startup fails the first time, the backoff interval is set to the value of vRtrLdpGenBackoffTime. Thereafter, if session startup fails again the backoff interval increases exponentially.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpBackoffTime 1..2592000  

vRtrLdpGenMaxBackoffTime 1.3.6.1.4.1.6527.3.1.2.8.1.1.21
The value of vRtrLdpGenMaxBackoffTime specifies the maximum value for the backoff interval. For each successive failure of the LDP session startup, the backoff interval (the time for which the router waits before retrying) increases exponentially. If the backoff interval exceeds vRtrLdpGenMaxBackoffTime, the router will give up trying to establish the LDP session. If vRtrLdpGenMaxBackoffTime is set to zero (0), then the backoff interval does not increase exponentially after the first session startup attempt fails. Instead it remains constant and LDP will keep retrying to establish a session until it succeeds.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpBackoffTime  

vRtrLdpGenTargKeepAliveFactor 1.3.6.1.4.1.6527.3.1.2.8.1.1.22
The value of vRtrLdpGenTargKeepAliveFactor specifies the value by which the keepalive timeout (vRtrLdpGenTargKeepAliveTimeout) should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors. This value is only applicable to targeted sessions and not to LDP interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpKeepAliveFactor  

vRtrLdpGenTargKeepAliveTimeout 1.3.6.1.4.1.6527.3.1.2.8.1.1.23
The value of vRtrLdpGenTargKeepAliveTimeout specifies the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Genly the value of vRtrLdpGenTargKeepAliveTimeout is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages). This value is only applicable to targeted sessions and not to LDP interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpKeepAliveTimeout  

vRtrLdpGenTargHelloFactor 1.3.6.1.4.1.6527.3.1.2.8.1.1.24
The value of vRtrLdpGenTargHelloFactor specifies the value by which the hello timeout (vRtrLdpGenTargHelloTimeout) should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors. This value is only applicable to targeted sessions and not to LDP interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpHelloFactor  

vRtrLdpGenTargHelloTimeout 1.3.6.1.4.1.6527.3.1.2.8.1.1.25
The value of vRtrLdpGenTargHelloTimeout specifies the hello time also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time. This value is only applicable to targeted sessions and not to LDP interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpHelloTimeout  

vRtrLdpGenTargPassiveMode 1.3.6.1.4.1.6527.3.1.2.8.1.1.26
The value of vRtrLdpGenTargPassiveMode specifies the mode used for setting up LDP sessions. When it has a value of 'true', LDP responds only when it gets a connect request from a peer and will not attempt to actively connect to its neighbors. When it has a value of 'false', LDP actively tries to connect to its peers. This value is only applicable to targeted sessions and not to LDP interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vRtrLdpGenTargetedSessions 1.3.6.1.4.1.6527.3.1.2.8.1.1.27
The value of vRtrLdpGenTargetedSessions specifies whether or not targeted sessions are allowed. Targeted sessions are LDP sessions between indirectly connected peers. The discovery messages for an indirect LDP session are addressed to the specified peer instead of to the multicast address. When this object has a value of 'true', targeted sessions are enabled. When its value is 'false', targeted sessions are disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vRtrLdpGenCreateTime 1.3.6.1.4.1.6527.3.1.2.8.1.1.28
The value of vRtrLdpGenCreateTime specifies the sysUpTime when this LDP instance was created.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vRtrLdpGenUpTime 1.3.6.1.4.1.6527.3.1.2.8.1.1.29
The value of vRtrLdpGenUpTime specifies the time, in hundreds of seconds, that the LDP instance has been operationally up.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

vRtrLdpGenImportPolicy1 1.3.6.1.4.1.6527.3.1.2.8.1.1.30
The value of vRtrLdpGenImportPolicy1 specifies the first import policy used to filter LDP label bindings received from LDP peers.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpGenImportPolicy2 1.3.6.1.4.1.6527.3.1.2.8.1.1.31
The value of vRtrLdpGenImportPolicy2 specifies the second import policy used to filter LDP label bindings received from LDP peers.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpGenImportPolicy3 1.3.6.1.4.1.6527.3.1.2.8.1.1.32
The value of vRtrLdpGenImportPolicy3 specifies the third import policy used to filter LDP label bindings received from LDP peers.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpGenImportPolicy4 1.3.6.1.4.1.6527.3.1.2.8.1.1.33
The value of vRtrLdpGenImportPolicy4 specifies the fourth import policy used to filter LDP label bindings received from LDP peers.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpGenImportPolicy5 1.3.6.1.4.1.6527.3.1.2.8.1.1.34
The value of vRtrLdpGenImportPolicy5 specifies the fifth import policy used to filter LDP label bindings received from LDP peers.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpGenExportPolicy1 1.3.6.1.4.1.6527.3.1.2.8.1.1.35
The value of vRtrLdpGenExportPolicy1 specifies the first export policy used to filter LDP label bindings advertised to LDP peers.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpGenExportPolicy2 1.3.6.1.4.1.6527.3.1.2.8.1.1.36
The value of vRtrLdpGenExportPolicy2 specifies the second export policy used to filter LDP label bindings advertised to LDP peers.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpGenExportPolicy3 1.3.6.1.4.1.6527.3.1.2.8.1.1.37
The value of vRtrLdpGenExportPolicy3 specifies the third export policy used to filter LDP label bindings advertised to LDP peers.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpGenExportPolicy4 1.3.6.1.4.1.6527.3.1.2.8.1.1.38
The value of vRtrLdpGenExportPolicy4 specifies the fourth export policy used to filter LDP label bindings advertised to LDP peers.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpGenExportPolicy5 1.3.6.1.4.1.6527.3.1.2.8.1.1.39
The value of vRtrLdpGenExportPolicy5 specifies the fifth export policy used to filter LDP label bindings advertised to LDP peers.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpGenTunnelDownDampTime 1.3.6.1.4.1.6527.3.1.2.8.1.1.40
The value of vRtrLdpGenTunnelDownDampTime specifies the time interval, in seconds, that LDP waits before posting a tunnel down event to the Route Table Manager. If a tunnel up event is generated before the damping interval has elapsed, a tunnel modify event will be posted to the Route Table Manager (RTM). If this value is set to 0, then tunnel down events are not damped.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..20  

vRtrLdpGenOperDownReason 1.3.6.1.4.1.6527.3.1.2.8.1.1.41
The value of vRtrLdpGenOperDownReason specifies the reason that the LDP instance is operationally down.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpGenOperDownReasonCode  

vRtrLdpGenTrustList 1.3.6.1.4.1.6527.3.1.2.8.1.1.42
The value of vRtrLdpGenTrustList specifies the IP filter ID used to verify trusted T-LDP peers. The IP filter specified by this object should contain a list of src-ip matches. The value '0' is not a valid IP filter ID, but it is used to indicate that there is no trust list. This object was obsoleted in release 5.0.
Status: obsolete Access: read-create
OBJECT-TYPE    
  TFilterID  

vRtrLdpGenGracefulRestart 1.3.6.1.4.1.6527.3.1.2.8.1.1.43
The value of vRtrLdpGenGracefulRestart specifies whether graceful restart helper is allowed. When this object has a value of 'true', graceful restart helper is enabled. When its value is 'false', graceful restart helper is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vRtrLdpGenGRNbrLiveTime 1.3.6.1.4.1.6527.3.1.2.8.1.1.44
The value of vRtrLdpGenGRNbrLiveTime specifies the value for neighbor liveness timer. The amount of time the Label Switching Router (LSR) keeps its stale label-FEC bindings is set to the lesser of the FT Reconnect Timeout, as was advertised by the neighbor, and this local timer, called the Neighbor Liveness Timer. The LSR waits for the specified time till a LDP session re-establishes itself. If within that time the LSR still does not establish an LDP session with the neighbor, all the stale bindings are deleted. This object has meaning only when vRtrLdpGenGracefulRestart is 'true'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 5..300  

vRtrLdpGenGRMaxRecoveryTime 1.3.6.1.4.1.6527.3.1.2.8.1.1.45
The value of vRtrLdpGenGRMaxRecoveryTime specifies the local maximum recovery time. If the Label Switching Router (LSR) determines that the neighbor was able to preserve its MPLS forwarding state (as was indicated by the non-zero Recovery Time advertised by the neighbor), the LSR should further keep the stale label-FEC bindings, received from the neighbor, for as long as the lesser of the Recovery Time advertised by the neighbor, and a local configurable value, called Maximum Recovery Time, allows. This object has meaning only when vRtrLdpGenGracefulRestart is 'true'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 15..1800  

vRtrLdpStatsTable 1.3.6.1.4.1.6527.3.1.2.8.2
vRtrLdpStatsTable is a read-only table. The purpose of this table is to keep statistical information about an LDP Instance. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpGeneralTable, and the augmenting table, vRtrLdpStatsTable. This in effect extends the vRtrLdpGeneralTable with additional columns. Creation or deletion of a row in the vRtrLdpGeneralTable results in the same fate for the row in the vRtrLdpStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpStatsEntry

vRtrLdpStatsEntry 1.3.6.1.4.1.6527.3.1.2.8.2.1
A row in this table represents statistical information about an LDP instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpStatsEntry  

vRtrLdpStatsOperDownEvents 1.3.6.1.4.1.6527.3.1.2.8.2.1.1
The value of vRtrLdpStatsOperDownEvents specifies the number of times the LDP instance has gone operationally down since the instance was created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsActiveSessions 1.3.6.1.4.1.6527.3.1.2.8.2.1.2
The value of vRtrLdpStatsActiveSessions specifies the number of active sessions (i.e. session in some form of creation) associated with the LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStatsActiveAdjacencies 1.3.6.1.4.1.6527.3.1.2.8.2.1.3
The value of vRtrLdpStatsActiveAdjacencies specifies the number of active adjacencies (i.e. established sessions) associated with the LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStatsActiveInterfaces 1.3.6.1.4.1.6527.3.1.2.8.2.1.4
The value of vRtrLdpStatsActiveInterfaces specifies the number of active (i.e. operationally up) interfaces associated with the LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStatsInactiveInterfaces 1.3.6.1.4.1.6527.3.1.2.8.2.1.5
The value of vRtrLdpStatsInactiveInterfaces specifies the number of inactive (i.e. operationally down) interfaces associated with the LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStatsActiveTargSessions 1.3.6.1.4.1.6527.3.1.2.8.2.1.6
The value of vRtrLdpStatsActiveTargSessions specifies the number of active (i.e. operationally up) targeted sessions associated with the LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStatsInactiveTargSessions 1.3.6.1.4.1.6527.3.1.2.8.2.1.7
The value of vRtrLdpStatsInactiveTargSessions specifies the number of inactive (i.e. operationally down) targeted sessions associated with the LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStatsAddrFECRecv 1.3.6.1.4.1.6527.3.1.2.8.2.1.8
The value of vRtrLdpStatsAddrFECRecv specifies the number of Address FECs received by the LDP instance from its neighbors.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStatsAddrFECSent 1.3.6.1.4.1.6527.3.1.2.8.2.1.9
The value of vRtrLdpStatsAddrFECSent specifies the number of Address FECs sent by the LDP instance to its neighbors.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStatsSvcFECRecv 1.3.6.1.4.1.6527.3.1.2.8.2.1.10
The value of vRtrLdpStatsSvcFECRecv specifies the number of Service FECs received by the LDP instance from its neighbors.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStatsSvcFECSent 1.3.6.1.4.1.6527.3.1.2.8.2.1.11
The value of vRtrLdpStatsSvcFECSent specifies the number of Service FECs sent by the LDP instance to its neighbors.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStatsAttemptedSessions 1.3.6.1.4.1.6527.3.1.2.8.2.1.12
The value of vRtrLdpStatsAttemptedSessions specifies the total number of attempted sessions for this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsSessRejNoHelloErrors 1.3.6.1.4.1.6527.3.1.2.8.2.1.13
The value of vRtrLdpStatsSessRejNoHelloErrors gives the total number of Session Rejected/No Hello Error Notification Messages sent or received by this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsSessRejAdvErrors 1.3.6.1.4.1.6527.3.1.2.8.2.1.14
The value of vRtrLdpStatsSessRejAdvErrors gives the total number of Session Rejected/Parameters Advertisement Mode Error Notification Messages sent or received by this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsSessRejMaxPduErrors 1.3.6.1.4.1.6527.3.1.2.8.2.1.15
The value of vRtrLdpStatsSessRejMaxPduErrors gives the total number of Session Rejected/Parameters Max Pdu Length Error Notification Messages sent or received by this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsSessRejLabelRangeErrors 1.3.6.1.4.1.6527.3.1.2.8.2.1.16
The value of vRtrLdpStatsSessRejLabelRangeErrors gives the total number of Session Rejected/Parameters Label Range Error Notification Messages sent or received by this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsBadLdpIdentifierErrors 1.3.6.1.4.1.6527.3.1.2.8.2.1.17
The value of vRtrLdpStatsBadLdpIdentifierErrors gives the number of Bad LDP Identifier Fatal Errors detected for sessions associated with this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsBadPduLengthErrors 1.3.6.1.4.1.6527.3.1.2.8.2.1.18
The value of vRtrLdpStatsBadPduLengthErrors gives the number of Bad Pdu Length Fatal Errors detected for sessions associated with this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsBadMessageLengthErrors 1.3.6.1.4.1.6527.3.1.2.8.2.1.19
The value of vRtrLdpStatsBadMessageLengthErrors gives the number of Bad Message Length Fatal Errors detected for sessions associated with this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsBadTlvLengthErrors 1.3.6.1.4.1.6527.3.1.2.8.2.1.20
The value of vRtrLdpStatsBadTlvLengthErrors gives the number of Bad TLV Length Fatal Errors detected for sessions associated with this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsMalformedTlvValueErrors 1.3.6.1.4.1.6527.3.1.2.8.2.1.21
The value of vRtrLdpStatsMalformedTlvValueErrors gives the number of Malformed TLV Value Fatal Errors detected for sessions associated with this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsKeepAliveExpiredErrors 1.3.6.1.4.1.6527.3.1.2.8.2.1.22
The value of vRtrLdpStatsKeepAliveExpiredErrors gives the number of Session Keep Alive Timer Expired Errors detected for sessions associated with this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsShutdownNotifRecv 1.3.6.1.4.1.6527.3.1.2.8.2.1.23
The value of vRtrLdpStatsShutdownNotifRecv gives the number of Shutdown Notifications received related to sessions associated with this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpStatsShutdownNotifSent 1.3.6.1.4.1.6527.3.1.2.8.2.1.24
The value of vRtrLdpStatsShutdownNotifSent gives the number of Shutdown Notifications sent related to sessions associated with this LDP instance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpPolicyTable 1.3.6.1.4.1.6527.3.1.2.8.3
vRtrLdpPolicyTable has an entry for each policy used by the LDP protocol instance running on the virtual router. This table is obsoleted in release 2.1.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpPolicyEntry

vRtrLdpPolicyEntry 1.3.6.1.4.1.6527.3.1.2.8.3.1
Each row entry represents a policy used by the LDP protocol instance. Entries can be created and deleted via SNMP SET operations to vRtrLdpPolicyRowStatus. This entry is obsoleted in release 2.1.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  VRtrLdpPolicyEntry  

vRtrLdpPolicyType 1.3.6.1.4.1.6527.3.1.2.8.3.1.1
The value of vRtrLdpPolicyType indicates the type of policy specified in this row entry. When vRtrLdpPolicyType has a value of 'import' this row entry represents the policy filter to be applied to the label binding received from a neighbor. When the value is 'export', this row entry represents the policy filter to determine the labels to be advertised to the neighbors. When the value is 'ingress', this row entry represents the policy filter to control the route prefixes that are advertised by LDP to the route table. LDP will advertise label bindings of prefixes that are advertised into it. When the value is 'egress', this row entry represents the policy filter to control the route prefixes that are advertised into LDP from the route table. LDP will advertise label bindings of prefixes that are advertised into it. This object is obsoleted in release 2.1.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER import(1), export(2), ingress(3), egress(4)  

vRtrLdpPolicyIndex 1.3.6.1.4.1.6527.3.1.2.8.3.1.2
vRtrLdpPolicyIndex is used to control the order that the LDP policies are applied. If multiple entries exist in this table with the same vRtrID and vRtrLdpPolicyType indexes, they are evaluated in ascending numeric order of vRtrLdpPolicyIndex (gaps are allowed). The first policy that matches is applied. This object is obsoleted in release 2.1.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..5  

vRtrLdpPolicyRowStatus 1.3.6.1.4.1.6527.3.1.2.8.3.1.3
vRtrLdpPolicyRowStatus controls the creation and deletion of rows in the vRtrLdpPolicyTable. This object is obsoleted in release 2.1.
Status: obsolete Access: read-create
OBJECT-TYPE    
  RowStatus  

vRtrLdpPolicyName 1.3.6.1.4.1.6527.3.1.2.8.3.1.4
The value of vRtrLdpPolicyName is the name of the policy filter to be used. If this object has the value of the empty string, ''H, there is no policy specified at this level. This object is obsoleted in release 2.1.
Status: obsolete Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpIfTableSpinlock 1.3.6.1.4.1.6527.3.1.2.8.4
Voluntary serialization control for vRtrLdpIfTable. Primarily used by SNMP manager to coordinate changes to vRtrLdpIfInheritance.
Status: current Access: read-write
OBJECT-TYPE    
  TestAndIncr  

vRtrLdpIfTable 1.3.6.1.4.1.6527.3.1.2.8.5
vRtrLdpIfTable provides an entry for each virtual router interface or targeted peer configured to be used with the Label Distribution Protocol (LDP).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpIfEntry

vRtrLdpIfEntry 1.3.6.1.4.1.6527.3.1.2.8.5.1
Each row entry represents an interface on this virtual router that participates in the LDP protocol. Row entries can be created or deleted via SNMP SET requests. A row with default attribute values is created by setting vRtrLdpIfRowStatus to 'createAndGo'. A row entry can be destroyed by setting vRtrLdpIfRowStatus to 'destroy'. An attempt to destroy a row will fail if vRtrLdpIfAdminState is not set to 'outOfService'.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpIfEntry  

vRtrLdpIfIndex 1.3.6.1.4.1.6527.3.1.2.8.5.1.1
vRtrLdpIfIndex is an index for the row entry and is used mutually exclusively with the vRtrLdpPeerAddress field. If the vRtrLdpPeerAddress field is 0.0.0.0, then vRtrLdpIfIndex is the index for the interface on the virtual router and must be non-zero. Otherwise, vRtrLdpPeerAddress refers to a targeted peer and its vRtrLdpIfIndex is 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpPeerAddress 1.3.6.1.4.1.6527.3.1.2.8.5.1.2
vRtrLdpPeerAddress is an index for the row entry and is used mutually exclusively with the vRtrLdpIfIndex field. If the vRtrLdpIfIndex field is 0, then the vRtrLdpPeerAddress is the IP address of the targeted peer and must be non-zero. Otherwise, vRtrLdpIfIndex refers to the LDP interface index and its vRtrLdpPeerAddress is 0.0.0.0
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

vRtrLdpIfRowStatus 1.3.6.1.4.1.6527.3.1.2.8.5.1.3
vRtrLdpIfRowStatus is used to control the creation and deletion of rows in the vRtrLdpIfTable. A row can be created by setting vRtrLdpIfRowStatus to 'createAndGo'. The agent should assign the default attribute values and change the row status to 'active'. A row entry can be destroyed by setting vRtrLdpIfRowStatus to 'destroy'. An attempt to destroy a row will fail if vRtrLdpIfAdminState is not set to 'outOfService'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vRtrLdpIfLastChange 1.3.6.1.4.1.6527.3.1.2.8.5.1.4
The value of vRtrLdpIfLastChange specifies the sysUpTime when this row was last modified.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vRtrLdpIfAdminState 1.3.6.1.4.1.6527.3.1.2.8.5.1.5
The value of vRtrLdpIfAdminState indicates the desired administrative state for LDP on this interface or targeted peer.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAdminState  

vRtrLdpIfOperState 1.3.6.1.4.1.6527.3.1.2.8.5.1.6
The value of vRtrLdpIfOperState specifies the current operational state of LDP on this interface or targeted peer.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOperState  

vRtrLdpIfInheritance 1.3.6.1.4.1.6527.3.1.2.8.5.1.7
Some writable object in this row that can be configured to inherit its value from its corresponding object in the vRtrLdpGeneralTable for LDP interfaces or from the corresponding object in the vRtrLdpIfTable for targeted peers. vRtrLdpIfInheritance controls whether to inherit the operational value of that object, or use the administratively set value. This object is a bit-mask, with the following positions: vRtrLdpIfKeepAliveFactor 0x1 vRtrLdpIfKeepAliveTimeout 0x2 vRtrLdpIfHelloFactor 0x4 vRtrLdpIfHelloTimeout 0x8 vRtrLdpIfBackoffTime 0x10 vRtrLdpIfMaxBackoffTime 0x20 vRtrLdpIfTransportAddrType 0x40 vRtrLdpIfPassiveMode 0x80 When the bit for an object is set to one, then the object's administrative and operational value are whatever the DEFVAL or most recently SET value is. When the bit for an object is set to zero, then the object's administrative and operational value are inherited from the corresponding object in vRtrLdpGeneralTable for LDP interfaces or the vRtrLdpIfTable for targeted peers.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vRtrLdpIfKeepAliveFactor 1.3.6.1.4.1.6527.3.1.2.8.5.1.8
The value of vRtrLdpIfKeepAliveFactor specifies the value by which the keepalive timeout (vRtrLdpIfKeepAliveTimeout) should be divided to give the keepalive time i.e. the time interval, in seconds, between LDP keepalive messages. LDP keepalive messages are sent to keep the LDP session from timing out when no other LDP traffic is being sent between the neighbors.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpKeepAliveFactor  

vRtrLdpIfKeepAliveTimeout 1.3.6.1.4.1.6527.3.1.2.8.5.1.9
The value of vRtrLdpIfKeepAliveTimeout specifies the time interval, in seconds, that LDP waits before tearing down a session. If no LDP messages are exchanged during this time interval, the LDP session is torn down. Generally the value of vRtrLdpIfKeepAliveTimeout is configured to be 3 times the keepalive time (the time interval between successive LDP keepalive messages).
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpKeepAliveTimeout  

vRtrLdpIfHelloFactor 1.3.6.1.4.1.6527.3.1.2.8.5.1.10
The value of vRtrLdpIfHelloFactor specifies the value by which the hello timeout (vRtrLdpIfHelloTimeout) should be divided to give the hello time i.e. the time interval, in seconds, between LDP Hello messages. LDP uses hello messages to discover neighbors and to detect loss of connectivity with its neighbors.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpHelloFactor  

vRtrLdpIfHelloTimeout 1.3.6.1.4.1.6527.3.1.2.8.5.1.11
The value of vRtrLdpIfHelloTimeout specifies the hello time also known as hold time. It is the time interval, in seconds, that LDP waits before declaring a neighbor to be down. Hello timeout is local to the system and is sent in the hello messages to a neighbor. Hello timeout cannot be set to a value that is less than 3 times the hello time.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpHelloTimeout  

vRtrLdpIfBackoffTime 1.3.6.1.4.1.6527.3.1.2.8.5.1.12
The value of vRtrLdpIfBackoffTime specifies the initial value for the backoff interval. The backoff interval is the time, in seconds, that LDP waits after an LDP session setup has failed before it attempts to setup the session again. After the LDP session startup fails the first time, the backoff interval is set to the value of vRtrLdpIfBackoffTime. Thereafter, if session startup fails again the backoff interval increases exponentially.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpBackoffTime 1..2592000  

vRtrLdpIfMaxBackoffTime 1.3.6.1.4.1.6527.3.1.2.8.5.1.13
The value of vRtrLdpIfMaxBackoffTime specifies the maximum value for the backoff interval. For each successive failure of the LDP session startup, the backoff interval (the time for which the router waits before retrying) increases exponentially. If the backoff interval exceeds vRtrLdpIfMaxBackoffTime, the router will give up trying to establish the LDP session. If vRtrLdpIfMaxBackoffTime is set to zero (0), then the backoff interval does not increase exponentially after the first session startup attempt fails. Instead it remains constant and LDP will keep retrying to establish a session until it succeeds.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxLdpBackoffTime  

vRtrLdpIfTransportAddrType 1.3.6.1.4.1.6527.3.1.2.8.5.1.14
The value of vRtrLdpIfTransportAddrType specifies the source of the transport address to be used when setting up the LDP TCP sessions. This value is meaningful only in case of LDP interfaces and not for targeted peers. When the value of this object is 'interface', the interface's IP address is used to setup the LDP session between neighbors. If multiple interfaces exist between two neighbors, the 'interface' mode cannot be used since only one LDP session is actually set up between the two neighbors. When the value of this object is 'system', the system's IP address is used to set up the LDP session between neighbors.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER interface(1), system(2)  

vRtrLdpIfPassiveMode 1.3.6.1.4.1.6527.3.1.2.8.5.1.15
The value of vRtrLdpIfPassiveMode specifies the mode used for setting up LDP sessions. This object is meaningful only in case of LDP targeted peers and not for interfaces. When it has a value of 'true', LDP responds only when it gets a connect request from a peer and will not attempt to actively connect to its neighbors. When it has a value of 'false', LDP actively tries to connect to its peers.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vRtrLdpIfAutoCreate 1.3.6.1.4.1.6527.3.1.2.8.5.1.16
The value of vRtrLdpIfAutoCreate specifies whether or not the row entry represents a targeted peer that was automatically created through Service Manager. For an LDP interface, this value is always false.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vRtrLdpIfOperDownReason 1.3.6.1.4.1.6527.3.1.2.8.5.1.17
The value of vRtrLdpIfOperDownReason specifies the reason that the LDP interface or targeted peer is operationally down.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpIntTargOperDownReasonCode  

vRtrLdpIfTunneling 1.3.6.1.4.1.6527.3.1.2.8.5.1.18
The value of vRtrLdpIfTunneling specifies whether tunneling of LDP over tunnels is enabled. When this object has a value of 'true', tunneling is enabled. When its value is 'false', tunneling is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vRtrLdpIfStatsTable 1.3.6.1.4.1.6527.3.1.2.8.6
vRtrLdpIfStatsTable is a read-only table. The purpose of this table is to keep statistical information about the LDP Interfaces and Targeted peers on the LSR. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpIfTable, and the augmenting table, vRtrLdpIfStatsTable. This in effect extends the vRtrLdpIfTable with additional columns. Creation or deletion of a row in the vRtrLdpIfTable results in the same fate for the row in the vRtrLdpIfStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpIfStatsEntry

vRtrLdpIfStatsEntry 1.3.6.1.4.1.6527.3.1.2.8.6.1
A row in this table contains statistical information about an LDP Interface or Targeted peer. Some counters contained in a row are for fatal errors received during a former LDP Session associated with this entry. For example, an LDP Pdu received on a TCP connection during an LDP Session contains a fatal error. That error is counted here, because the session is terminated. If the error is NOT fatal (i.e. and the Session remains), then the error is counted in the vRtrLdpSessionStatsEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpIfStatsEntry  

vRtrLdpIfExistingAdjacencies 1.3.6.1.4.1.6527.3.1.2.8.6.1.1
The value of vRtrLdpIfExistingAdjacencies gives a count of the total active adjacencies on this LDP interface or with this targeted peer.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpHelloAdjTable 1.3.6.1.4.1.6527.3.1.2.8.7
vRtrLdpHelloAdjTable is a read-only table. The purpose of this table is to keep information about Hello Adjacencies for Sessions. A hello adjacency can be associated with an LDP interface or with a targeted peer. The index includes both the interface index and the peer IP address thus referring to the LDP interface or targeted peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpHelloAdjEntry

vRtrLdpHelloAdjEntry 1.3.6.1.4.1.6527.3.1.2.8.7.1
Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpHelloAdjEntry  

vRtrLdpPeerLdpId 1.3.6.1.4.1.6527.3.1.2.8.7.1.1
vRtrLdpPeerLdpId is an index for the row entry. It specifies the LDP identifier of the peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  MplsLdpIdentifier  

vRtrLdpHelloAdjLocalLdpId 1.3.6.1.4.1.6527.3.1.2.8.7.1.2
The value of vRtrLdpHelloAdjLocalLdpId specifies the local LDP identifier for this specific adjacency.
Status: current Access: read-only
OBJECT-TYPE    
  MplsLdpIdentifier  

vRtrLdpHelloAdjEntityIndex 1.3.6.1.4.1.6527.3.1.2.8.7.1.3
The value of vRtrLdpHelloAdjEntityIndex specifies the Entity index which is an index for the mplsLdpHelloAdjacencyEntry defined in MPLS-LDP-MIB.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

vRtrLdpHelloAdjIndex 1.3.6.1.4.1.6527.3.1.2.8.7.1.4
The value of vRtrLdpHelloAdjIndex gives the Hello adjacency index which is an index for the mplsLdpHelloAdjacencyEntry defined in MPLS-LDP-MIB.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

vRtrLdpHelloAdjHoldTimeRemaining 1.3.6.1.4.1.6527.3.1.2.8.7.1.5
The value of vRtrLdpHelloAdjHoldTimeRemaining specifies the hold time remaining for this Hello Adjacency. This interval will change when the next Hello message which corresponds to this Hello Adjacency is received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpHelloAdjType 1.3.6.1.4.1.6527.3.1.2.8.7.1.6
The value of vRtrLdpHelloAdjType specifies the type of this Hello Adjacency. If this value is 'link' then this adjacency is a result of a Link Hello. If this value is 'hello', then the adjacency is a result of a Targeted Hello.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpAdjacencyType  

vRtrLdpHelloAdjRemoteConfSeqNum 1.3.6.1.4.1.6527.3.1.2.8.7.1.7
The value of vRtrLdpHelloAdjRemoteConfSeqNum specifies the Configuration sequence number that was in the Hello received when this adjacency started up. This configuration sequence number changes when there is a change of configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpHelloAdjRemoteIpAddress 1.3.6.1.4.1.6527.3.1.2.8.7.1.8
The value of vRtrLdpHelloAdjRemoteIpAddress specifies the peer IP address of the interface/targeted session that sent hellos for this specific adjacency.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpHelloAdjUpTime 1.3.6.1.4.1.6527.3.1.2.8.7.1.9
The value of vRtrLdpHelloAdjUpTime specifies the time, in hundreds of seconds, that this adjacency has been up.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

vRtrLdpHelloAdjLocalConfSeqNum 1.3.6.1.4.1.6527.3.1.2.8.7.1.10
The value of vRtrLdpHelloAdjLocalConfSeqNum specifies the Configuration sequence number that was used in the Hello sent when this adjacency started up. This configuration sequence number changes when there is a change of configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpHelloAdjLocalIpAddress 1.3.6.1.4.1.6527.3.1.2.8.7.1.11
The value of vRtrLdpHelloAdjLocalIpAddress specifies the local IP address of the interface/targeted session used in Hellos sent for this specific adjacency.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpHelloAdjInHelloMsgCount 1.3.6.1.4.1.6527.3.1.2.8.7.1.12
The value of vRtrLdpHelloAdjInHelloMsgCount specifies the number of Hello messages that have been received for this adjacency.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpHelloAdjOutHelloMsgCount 1.3.6.1.4.1.6527.3.1.2.8.7.1.13
The value of vRtrLdpHelloAdjOutHelloMsgCount specifies the number of Hello messages that have been sent for this adjacency.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpHelloAdjLocalHelloTimeout 1.3.6.1.4.1.6527.3.1.2.8.7.1.14
The value of vRtrLdpHelloAdjLocalHelloTimeout specifies the hello timeout used in the Hellos sent for this specific adjacency.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpHelloTimeout  

vRtrLdpHelloAdjRemoteHelloTimeout 1.3.6.1.4.1.6527.3.1.2.8.7.1.15
The value of vRtrLdpHelloAdjRemoteHelloTimeout specifies the hello timeout used by the remote end that sent Hellos for this specific adjacency.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpHelloTimeout  

vRtrLdpHelloAdjMapTable 1.3.6.1.4.1.6527.3.1.2.8.8
vRtrLdpHelloAdjMapTable is a read-only table which maps to the vRtrLdpHelloAdjTable. This table has the same indexes as the vRtrLdpHelloAdjTable but the order in which these indexes are specified is different for the two tables.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpHelloAdjMapEntry

vRtrLdpHelloAdjMapEntry 1.3.6.1.4.1.6527.3.1.2.8.8.1
Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpHelloAdjMapEntry  

vRtrLdpHelloAdjMapLdpId 1.3.6.1.4.1.6527.3.1.2.8.8.1.1
vRtrLdpHelloAdjMapLdpId is an index for the row entry. It specifies the LDP identifier of the peer.
Status: current Access: read-only
OBJECT-TYPE    
  MplsLdpIdentifier  

vRtrLdpSessionTable 1.3.6.1.4.1.6527.3.1.2.8.9
vRtrLdpSessionTable is a read-only table which parallels the mplsLdpSessionTable in the MPLS-LDP-MIB. The purpose of this table is to keep information about a single session between an LDP entity and an LDP Peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpSessionEntry

vRtrLdpSessionEntry 1.3.6.1.4.1.6527.3.1.2.8.9.1
A row in this table represents information about a single session between an LDP entity and an LDP Peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpSessionEntry  

vRtrLdpSessLocalLdpId 1.3.6.1.4.1.6527.3.1.2.8.9.1.1
The value of vRtrLdpSessLocalLdpId specifies the local LDP identifier for this LDP session.
Status: current Access: read-only
OBJECT-TYPE    
  MplsLdpIdentifier  

vRtrLdpSessEntityIndex 1.3.6.1.4.1.6527.3.1.2.8.9.1.2
The value of vRtrLdpSessEntityIndex specifies the Entity index for the LDP entity represented in this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

vRtrLdpSessLabelDistMethod 1.3.6.1.4.1.6527.3.1.2.8.9.1.3
The value of vRtrLdpSessLabelDistMethod specifies the label distribution method used for this LDP session.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpLabelDistMethod  

vRtrLdpSessLoopDetectForPV 1.3.6.1.4.1.6527.3.1.2.8.9.1.4
The value of vRtrLdpSessLoopDetectForPV indicates whether loop detection based on path vectors is disabled or enabled for this LDP session. If this object has a value of disabled(0), then loop detection is disabled. Otherwise, if this object has a value of enabled(1), then loop detection based on path vectors is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

vRtrLdpSessPathVectorLimit 1.3.6.1.4.1.6527.3.1.2.8.9.1.5
If the value of vRtrLdpSessLoopDetectForPV for this entry is 'enabled', then the value of vRtrLdpSessPathVectorLimit represents the Path Vector Limit for this LDP Session. If the value of vRtrLdpSessLoopDetectForPV for this entry is 'disabled', then the value of vRtrLdpSessPathVectorLimit be 0 (zero).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

vRtrLdpSessState 1.3.6.1.4.1.6527.3.1.2.8.9.1.6
The value of vRtrLdpSessState specifies the current state of the LDP session. All of the states 1 - 5 are based on the state machine for session negotiation behavior.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER nonexistent(1), initialized(2), openrec(3), opensent(4), operational(5)  

vRtrLdpSessAdjacencyType 1.3.6.1.4.1.6527.3.1.2.8.9.1.7
The value of vRtrLdpSessAdjacencyType specifies the adjacency type(s) supporting this LDP Session.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpAdjacencyType  

vRtrLdpSessProtocolVersion 1.3.6.1.4.1.6527.3.1.2.8.9.1.8
The value of vRtrLdpSessProtocolVersion specifies the version of the LDP Protocol used by this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpSessLocalUdpPort 1.3.6.1.4.1.6527.3.1.2.8.9.1.9
The value of vRtrLdpSessLocalUdpPort specifies the UDP port used locally for LDP discovery.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

vRtrLdpSessPeerUdpPort 1.3.6.1.4.1.6527.3.1.2.8.9.1.10
The value of vRtrLdpSessPeerUdpPort specifies the UDP port used on the remote end for LDP discovery.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

vRtrLdpSessLocalTcpPort 1.3.6.1.4.1.6527.3.1.2.8.9.1.11
The value of vRtrLdpSessLocalTcpPort specifies the TCP port used locally for the LDP Session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

vRtrLdpSessPeerTcpPort 1.3.6.1.4.1.6527.3.1.2.8.9.1.12
The value of vRtrLdpSessPeerTcpPort specifies the TCP port used on the remote end for the LDP Session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

vRtrLdpSessLocalAddress 1.3.6.1.4.1.6527.3.1.2.8.9.1.13
The value of vRtrLdpSessLocalAddress specifies the IP address used locally for the LDP Session.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpSessPeerAddress 1.3.6.1.4.1.6527.3.1.2.8.9.1.14
The value of vRtrLdpSessPeerAddress specifies the IP address used on the remote end for the LDP Session.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpSessKAHoldTimeRemaining 1.3.6.1.4.1.6527.3.1.2.8.9.1.15
The value of vRtrLdpSessKAHoldTimeRemaining specifies the keep alive hold time remaining, in hundredths of seconds, for this LDP session.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

vRtrLdpSessMaxPduLength 1.3.6.1.4.1.6527.3.1.2.8.9.1.16
The value of vRtrLdpSessMaxPduLength specifies the maximum allowable length for LDP PDUs for this session. This value may have been negotiated during Session Initialization.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..65535  

vRtrLdpSessUpTime 1.3.6.1.4.1.6527.3.1.2.8.9.1.17
The value of vRtrLdpSessUpTime specifies the time, in hundreds of seconds, since the session was established.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

vRtrLdpSessLocalKATimeout 1.3.6.1.4.1.6527.3.1.2.8.9.1.18
The value of vRtrLdpSessLocalKATimeout specifies the keepalive timeout used locally for the LDP Session.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpKeepAliveTimeout  

vRtrLdpSessPeerKATimeout 1.3.6.1.4.1.6527.3.1.2.8.9.1.19
The value of vRtrLdpSessPeerKATimeout specifies the keepalive timeout used at the remote end of the LDP Session.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpKeepAliveTimeout  

vRtrLdpSessAdvertise 1.3.6.1.4.1.6527.3.1.2.8.9.1.20
The value of vRtrLdpSessAdvertise indicates the type of FECs that will be transported by the session.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER address(1), service(2), addressAndService(3)  

vRtrLdpSessRestartHelperState 1.3.6.1.4.1.6527.3.1.2.8.9.1.21
The value of vRtrLdpSessRestartHelperState indicates whether the entity session is capable of supporting graceful restart. This is negotiated between peers during the session initialization setup.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vRtrLdpSessPeerNumRestart 1.3.6.1.4.1.6527.3.1.2.8.9.1.22
The value of vRtrLdpSessPeerNumRestart indicates the number of times graceful restart helper was initiated for this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessLastRestartTime 1.3.6.1.4.1.6527.3.1.2.8.9.1.23
The value of vRtrLdpSessLastRestartTime indicates the last time graceful restart helper was initiated.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vRtrLdpSessFtReconnectTimeNego 1.3.6.1.4.1.6527.3.1.2.8.9.1.24
The value of vRtrLdpSessFtReconnectTimeNego indicates the session's Fault Tolerant(FT) Reconnect Timeout, it is set to the lesser of the neighbor advertised FT Reconnect Timeout, vRtrLdpSessFtReconTimeRemaining and the local timer Neighbor Liveness Time, vRtrLdpGenGRNbrLiveTime. It is within this period that the transport session is expected to re-establish, failure to do so will cause the teardown of the LDP session and deletion of stale bindings.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpSessFtRecoveryTimeNego 1.3.6.1.4.1.6527.3.1.2.8.9.1.25
The value of vRtrLdpSessFtRecoveryTimeNego indicates the session's Fault Tolerant(FT) recovery timeout, it is set to the lesser of the neighbor advertised FT recovery timeout, vRtrLdpSessFtRecovTimeRemaining and the local timer maximum recovery time, vRtrLdpGenGRMaxRecoveryTime. It is within this period that label-FEC binding message exchanges are expected to complete. Any stale FEC entries left after this time will be deleted from the FEC table.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpSessFtReconTimeRemaining 1.3.6.1.4.1.6527.3.1.2.8.9.1.26
The value of vRtrLdpSessFtReconTimeRemaining indicates the amount of time left before the session's Fault Tolerant(FT) reconnect timeout,vRtrLdpSessFtReconnectTimeNego expires.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpSessFtRecovTimeRemaining 1.3.6.1.4.1.6527.3.1.2.8.9.1.27
This value indicates the amount of time left before session's Fault Tolerant(FT) recovery timeout, vRtrLdpSessFtRecoveryTimeNego expires.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpSessionStatsTable 1.3.6.1.4.1.6527.3.1.2.8.10
vRtrLdpSessionStatsTable is a read-only table. The purpose of this table is to keep statistical information about a single session between an LDP entity and an LDP Peer. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpSessionTable, and the augmenting table, vRtrLdpSessionStatsTable. This in effect extends the vRtrLdpSessionTable with additional columns. Creation or deletion of a row in the vRtrLdpSessionTable results in the same fate for the row in the vRtrLdpSessionStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpSessionStatsEntry

vRtrLdpSessionStatsEntry 1.3.6.1.4.1.6527.3.1.2.8.10.1
A row in this table represents statistical information about a single session between an LDP entity and an LDP Peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpSessionStatsEntry  

vRtrLdpSessStatsTargAdj 1.3.6.1.4.1.6527.3.1.2.8.10.1.1
The value of vRtrLdpSessStatsTargAdj specifies the number of targeted adjacencies for this session.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpSessStatsLinkAdj 1.3.6.1.4.1.6527.3.1.2.8.10.1.2
The value of vRtrLdpSessStatsLinkAdj specifies the number of link adjacencies for this session.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpSessStatsFECRecv 1.3.6.1.4.1.6527.3.1.2.8.10.1.3
The value of vRtrLdpSessStatsFECRecv counts the number of FECs received for this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsFECSent 1.3.6.1.4.1.6527.3.1.2.8.10.1.4
The value of vRtrLdpSessStatsFECSent counts the number of FECs sent for this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsHelloIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.5
The value of vRtrLdpSessStatsHelloIn counts the number of Hello Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsHelloOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.6
The value of vRtrLdpSessStatsHelloOut counts the number of Hello Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsKeepaliveIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.7
The value of vRtrLdpSessStatsKeepaliveIn counts the number of Keepalive Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsKeepaliveOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.8
The value of vRtrLdpSessStatsKeepaliveOut counts the number of Keepalive Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsInitIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.9
The value of vRtrLdpSessStatsInitIn counts the number of Init Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsInitOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.10
The value of vRtrLdpSessStatsInitOut counts the number of Init Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsLabelMappingIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.11
The value of vRtrLdpSessStatsLabelMappingIn counts the number of Label Mapping Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsLabelMappingOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.12
The value of vRtrLdpSessStatsLabelMappingOut counts the number of Label Mapping Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsLabelRequestIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.13
The value of vRtrLdpSessStatsLabelRequestIn counts the number of Label Request Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsLabelRequestOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.14
The value of vRtrLdpSessStatsLabelRequestOut counts the number of Label Request Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsLabelReleaseIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.15
The value of vRtrLdpSessStatsLabelReleaseIn counts the number of Label Release Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsLabelReleaseOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.16
The value of vRtrLdpSessStatsLabelReleaseOut counts the number of Label Release Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsLabelWithdrawIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.17
The value of vRtrLdpSessStatsLabelWithdrawIn counts the number of Label Withdraw Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsLabelWithdrawOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.18
The value of vRtrLdpSessStatsLabelWithdrawOut counts the number of Label Withdraw Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsLabelAbortIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.19
The value of vRtrLdpSessStatsLabelAbortIn counts the number of Label Abort Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsLabelAbortOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.20
The value of vRtrLdpSessStatsLabelAbortOut counts the number of Label Abort Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsAddrIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.21
The value of vRtrLdpSessStatsAddrIn counts the number of Address Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsAddrOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.22
The value of vRtrLdpSessStatsAddrOut counts the number of Address Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsAddrWithdrawIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.23
The value of vRtrLdpSessStatsAddrWithdrawIn counts the number of Address Withdraw Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsAddrWithdrawOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.24
The value of vRtrLdpSessStatsAddrWithdrawOut counts the number of Address Withdraw Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsNotificationIn 1.3.6.1.4.1.6527.3.1.2.8.10.1.25
The value of vRtrLdpSessStatsNotificationIn counts the number of Notification Messages that have been received during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpSessStatsNotificationOut 1.3.6.1.4.1.6527.3.1.2.8.10.1.26
The value of vRtrLdpSessStatsNotificationOut counts the number of Notification Messages that have been sent during this session.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vRtrLdpServFecTable 1.3.6.1.4.1.6527.3.1.2.8.11
vRtrLdpServFecTable is a read-only table that represents all service FECs either sent to or received from an LDP peer known to the Virtual Router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpServFecEntry

vRtrLdpServFecEntry 1.3.6.1.4.1.6527.3.1.2.8.11.1
Each row entry represents an instance of a service FEC sent to or received from an LDP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpServFecEntry  

vRtrLdpServFecFecType 1.3.6.1.4.1.6527.3.1.2.8.11.1.1
The value of vRtrLdpServFecFecType specifies the FEC type.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxLdpFECType  

vRtrLdpServFecVcType 1.3.6.1.4.1.6527.3.1.2.8.11.1.2
The value of vRtrLdpServFecVcType specifies the VC type associated with this service FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxVcType  

vRtrLdpServFecVcId 1.3.6.1.4.1.6527.3.1.2.8.11.1.3
The value of vRtrLdpServFecVcId specifies the VC identifier associated with this service FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxVcId  

vRtrLdpServFecServType 1.3.6.1.4.1.6527.3.1.2.8.11.1.4
The value of vRtrLdpServFecServType specifies the Service type associated with this service FEC.
Status: current Access: read-only
OBJECT-TYPE    
  ServType  

vRtrLdpServFecServId 1.3.6.1.4.1.6527.3.1.2.8.11.1.5
The value of vRtrLdpServFecServId specifies the Service identifier associated with this service FEC.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxServId 1..2147483647  

vRtrLdpServFecVpnId 1.3.6.1.4.1.6527.3.1.2.8.11.1.6
The value of vRtrLdpServFecVpnId identifies the VPN associated with the FEC.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxVpnId  

vRtrLdpServFecFlags 1.3.6.1.4.1.6527.3.1.2.8.11.1.7
The bit flags of vRtrLdpServFecFlags specify the characteristics of the FEC.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpFECFlags  

vRtrLdpServFecNumInLabels 1.3.6.1.4.1.6527.3.1.2.8.11.1.8
The value of vRtrLdpServFecNumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This value also indicates which of the following vRtrLdpServFecInLabel1 thru vRtrLdpServFecInLabel5 entries contain valid information i.e. if the value of vRtrLdpServFecNumInLabels is 3 then vRtrLdpServFecInLabel1, vRtrLdpServFecInLabel2 and vRtrLdpServFecInLabel3 will contain valid label information.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecNumOutLabels 1.3.6.1.4.1.6527.3.1.2.8.11.1.9
The value of vRtrLdpServFecNumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This value also indicates which of the following vRtrLdpServFecOutLabel1 thru vRtrLdpServFecOutLabel5 entries contain valid information i.e. if the value of vRtrLdpServFecNumOutLabels is 3, then vRtrLdpServFecOutLabel1, vRtrLdpServFecOutLabel2 and vRtrLdpServFecOutLabel3 will contain valid label information.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecInLabel1 1.3.6.1.4.1.6527.3.1.2.8.11.1.10
The value of vRtrLdpServFecInLabel1 specifies the first ingress label exchanged
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecInLabelStatus1 1.3.6.1.4.1.6527.3.1.2.8.11.1.11
The value of vRtrLdpServFecInLabelStatus1 specifies the status of the ingress label 1
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpServFecInLabel2 1.3.6.1.4.1.6527.3.1.2.8.11.1.12
The value of vRtrLdpServFecInLabel2 specifies the second ingress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecInLabelStatus2 1.3.6.1.4.1.6527.3.1.2.8.11.1.13
The value of vRtrLdpServFecInLabelStatus2 specifies the status of the ingress label 2
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpServFecInLabel3 1.3.6.1.4.1.6527.3.1.2.8.11.1.14
The value of vRtrLdpServFecInLabel3 specifies the third ingress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecInLabelStatus3 1.3.6.1.4.1.6527.3.1.2.8.11.1.15
The value of vRtrLdpServFecInLabelStatus3 specifies the status of the ingress label 3
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpServFecInLabel4 1.3.6.1.4.1.6527.3.1.2.8.11.1.16
The value of vRtrLdpServFecInLabel4 specifies the fourth ingress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecInLabelStatus4 1.3.6.1.4.1.6527.3.1.2.8.11.1.17
The value of vRtrLdpServFecInLabelStatus4 specifies the status of the ingress label 4
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpServFecInLabel5 1.3.6.1.4.1.6527.3.1.2.8.11.1.18
The value of vRtrLdpServFecInLabel5 specifies the fifth ingress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecInLabelStatus5 1.3.6.1.4.1.6527.3.1.2.8.11.1.19
The value of vRtrLdpServFecInLabelStatus5 specifies the status of the ingress label 5
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpServFecOutLabel1 1.3.6.1.4.1.6527.3.1.2.8.11.1.20
The value of vRtrLdpServFecOutLabel1 specifies the first egress label exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecOutLabelStatus1 1.3.6.1.4.1.6527.3.1.2.8.11.1.21
The value of vRtrLdpServFecOutLabelStatus1 specifies the status of the egress label 1
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpServFecOutLabel2 1.3.6.1.4.1.6527.3.1.2.8.11.1.22
The value of vRtrLdpServFecOutLabel2 specifies the second egress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecOutLabelStatus2 1.3.6.1.4.1.6527.3.1.2.8.11.1.23
The value of vRtrLdpServFecOutLabelStatus2 specifies the status of the egress label 2
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpServFecOutLabel3 1.3.6.1.4.1.6527.3.1.2.8.11.1.24
The value of vRtrLdpServFecOutLabel3 specifies the third egress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecOutLabelStatus3 1.3.6.1.4.1.6527.3.1.2.8.11.1.25
The value of vRtrLdpServFecOutLabelStatus3 specifies the status of the egress label 3
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpServFecOutLabel4 1.3.6.1.4.1.6527.3.1.2.8.11.1.26
The value of vRtrLdpServFecOutLabel4 specifies the fourth egress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecOutLabelStatus4 1.3.6.1.4.1.6527.3.1.2.8.11.1.27
The value of vRtrLdpServFecOutLabelStatus4 specifies the status of the egress label 4
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpServFecOutLabel5 1.3.6.1.4.1.6527.3.1.2.8.11.1.28
The value of vRtrLdpServFecOutLabel5 specifies the fifth egress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecOutLabelStatus5 1.3.6.1.4.1.6527.3.1.2.8.11.1.29
The value of vRtrLdpServFecOutLabelStatus5 specifies the status of the egress label 5
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpServFecSdpId 1.3.6.1.4.1.6527.3.1.2.8.11.1.30
The value of vRtrLdpServFecSdpId identifies the SDP associated with this peer.
Status: current Access: read-only
OBJECT-TYPE    
  SdpId  

vRtrLdpServFecLocalMTU 1.3.6.1.4.1.6527.3.1.2.8.11.1.31
The value of vRtrLdpServFecLocalMTU specifies the largest service frame size (in octets) that can be handled by the local ESR.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecRemoteMTU 1.3.6.1.4.1.6527.3.1.2.8.11.1.32
The value of vRtrLdpServFecRemoteMTU specifies the largest service frame size (in octets) that can be handled by the remote ESR.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecLocalVlanTag 1.3.6.1.4.1.6527.3.1.2.8.11.1.33
The value of vRtrLdpServFecLocalVlanTag specifies the local tag on a VLAN VC type SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecRemoteVlanTag 1.3.6.1.4.1.6527.3.1.2.8.11.1.34
The value of vRtrLdpServFecRemoteVlanTag specifies the remote tag on a VLAN VC type SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecLocalMaxCellConcat 1.3.6.1.4.1.6527.3.1.2.8.11.1.35
The value of vRtrLdpServFecLocalMaxCellConcat specifies the local maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecRemoteMaxCellConcat 1.3.6.1.4.1.6527.3.1.2.8.11.1.36
The value of vRtrLdpServFecRemoteMaxCellConcat specifies the remote maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpServFecInLabelSigStatus1 1.3.6.1.4.1.6527.3.1.2.8.11.1.37
The value of vRtrLdpServFecInLabelSigStatus1 indicates the signaling status for vRtrLdpServFecInLabel1.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vRtrLdpServFecInLabelSigStatus2 1.3.6.1.4.1.6527.3.1.2.8.11.1.38
The value of vRtrLdpServFecInLabelSigStatus2 indicates the signaling status for vRtrLdpServFecInLabel2.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vRtrLdpServFecInLabelSigStatus3 1.3.6.1.4.1.6527.3.1.2.8.11.1.39
The value of vRtrLdpServFecInLabelSigStatus3 indicates the signaling status for vRtrLdpServFecInLabel3.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vRtrLdpServFecInLabelSigStatus4 1.3.6.1.4.1.6527.3.1.2.8.11.1.40
The value of vRtrLdpServFecInLabelSigStatus4 indicates the signaling status for vRtrLdpServFecInLabel4.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vRtrLdpServFecInLabelSigStatus5 1.3.6.1.4.1.6527.3.1.2.8.11.1.41
The value of vRtrLdpServFecInLabelSigStatus5 indicates the signaling status for vRtrLdpServFecInLabel5.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vRtrLdpServFecOutLabelSigStatus1 1.3.6.1.4.1.6527.3.1.2.8.11.1.42
The value of vRtrLdpServFecOutLabelSigStatus1 indicates the signaling status for vRtrLdpServFecOutLabel1.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vRtrLdpServFecOutLabelSigStatus2 1.3.6.1.4.1.6527.3.1.2.8.11.1.43
The value of vRtrLdpServFecOutLabelSigStatus2 indicates the signaling status for vRtrLdpServFecOutLabel2.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vRtrLdpServFecOutLabelSigStatus3 1.3.6.1.4.1.6527.3.1.2.8.11.1.44
The value of vRtrLdpServFecOutLabelSigStatus3 indicates the signaling status for vRtrLdpServFecOutLabel3.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vRtrLdpServFecOutLabelSigStatus4 1.3.6.1.4.1.6527.3.1.2.8.11.1.45
The value of vRtrLdpServFecOutLabelSigStatus4 indicates the signaling status for vRtrLdpServFecOutLabel4.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vRtrLdpServFecOutLabelSigStatus5 1.3.6.1.4.1.6527.3.1.2.8.11.1.46
The value of vRtrLdpServFecOutLabelSigStatus5 indicates the signaling status for vRtrLdpServFecOutLabel5.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vRtrLdpServFecMateEndpointVcId 1.3.6.1.4.1.6527.3.1.2.8.11.1.47
The value of vRtrLdpServFecMateEndpointVcId specifies the VC identifier associated with this service FEC mate endpoint for vc-switching.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxVcId  

vRtrLdpServFecMateEndpointSdpId 1.3.6.1.4.1.6527.3.1.2.8.11.1.48
The value of vRtrLdpServFecMateEndpointSdpId identifies the SDP associated with this service FEC mate endpoint for vc-switching.
Status: current Access: read-only
OBJECT-TYPE    
  SdpId  

vRtrLdpServFecMapTable 1.3.6.1.4.1.6527.3.1.2.8.12
vRtrLdpServFecMapTable is a read-only table which maps to the vRtrLdpServFecTable. This table has the same indexes as the vRtrLdpServFecTable but the order in which these indexes are specified is different for the two tables.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpServFecMapEntry

vRtrLdpServFecMapEntry 1.3.6.1.4.1.6527.3.1.2.8.12.1
Each row entry represents an instance of a service FEC sent to or received from an LDP peer.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  VRtrLdpServFecMapEntry  

vRtrLdpServFecMapFecType 1.3.6.1.4.1.6527.3.1.2.8.12.1.1
The value of vRtrLdpServFecMapFecType specifies the FEC type.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxLdpFECType  

vRtrLdpServFecMapVcType 1.3.6.1.4.1.6527.3.1.2.8.12.1.2
The value of vRtrLdpServFecMapVcType specifies the VC type associated with this service FEC.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxVcType  

vRtrLdpServFecMapVcId 1.3.6.1.4.1.6527.3.1.2.8.12.1.3
The value of vRtrLdpServFecMapVcId specifies the VC identifier associated with this service FEC.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxVcId  

vRtrLdpAddrFecTable 1.3.6.1.4.1.6527.3.1.2.8.13
vRtrLdpAddrFecTable is a read-only table that represents all address FECs either sent to or received from an LDP peer known to the Virtual Router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpAddrFecEntry

vRtrLdpAddrFecEntry 1.3.6.1.4.1.6527.3.1.2.8.13.1
Each row entry represents an instance of an address FEC sent to or received from an LDP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpAddrFecEntry  

vRtrLdpAddrFecFecType 1.3.6.1.4.1.6527.3.1.2.8.13.1.1
The value of vRtrLdpAddrFecFecType specifies the FEC type.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxLdpFECType  

vRtrLdpAddrFecIpPrefix 1.3.6.1.4.1.6527.3.1.2.8.13.1.2
The value of vRtrLdpAddrFecIpPrefix specifies the IP Address Prefix for this address FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

vRtrLdpAddrFecIpMask 1.3.6.1.4.1.6527.3.1.2.8.13.1.3
The value of vRtrLdpAddrFecIpMask specifies the IP Address Mask for this address FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

vRtrLdpAddrFecFlags 1.3.6.1.4.1.6527.3.1.2.8.13.1.4
The bit flags of vRtrLdpAddrFecFlags specify the characteristics of the FEC.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpFECFlags  

vRtrLdpAddrFecNumInLabels 1.3.6.1.4.1.6527.3.1.2.8.13.1.5
The value of vRtrLdpAddrFecNumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This value also indicates which of the following vRtrLdpAddrFecInLabel1 thru vRtrLdpAddrFecInLabel5 entries contain valid information i.e. if the value of vRtrLdpAddrFecNumInLabels is 3 then vRtrLdpAddrFecInLabel1, vRtrLdpAddrFecInLabel2 and vRtrLdpAddrFecInLabel3 will contain valid label information.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecNumOutLabels 1.3.6.1.4.1.6527.3.1.2.8.13.1.6
The value of vRtrLdpAddrFecNumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This value also indicates which of the following vRtrLdpAddrFecOutLabel1 thru vRtrLdpAddrFecOutLabel5 entries contain valid information i.e. if the value of vRtrLdpAddrFecNumOutLabels is 3, then vRtrLdpAddrFecOutLabel1, vRtrLdpAddrFecOutLabel2 and vRtrLdpAddrFecOutLabel3 will contain valid label information.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecInLabel1 1.3.6.1.4.1.6527.3.1.2.8.13.1.7
The value of vRtrLdpAddrFecInLabel1 specifies the first ingress label exchanged
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecInLabelStatus1 1.3.6.1.4.1.6527.3.1.2.8.13.1.8
The value of vRtrLdpAddrFecInLabelStatus1 specifies the status of the ingress label 1
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpAddrFecInLabelIfIndex1 1.3.6.1.4.1.6527.3.1.2.8.13.1.9
The value of vRtrLdpAddrFecInLabelIfIndex1 specifies the interface index for ingress label 1
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpAddrFecInLabel2 1.3.6.1.4.1.6527.3.1.2.8.13.1.10
The value of vRtrLdpAddrFecInLabel2 specifies the second ingress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecInLabelStatus2 1.3.6.1.4.1.6527.3.1.2.8.13.1.11
The value of vRtrLdpAddrFecInLabelStatus2 specifies the status of the ingress label
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpAddrFecInLabelIfIndex2 1.3.6.1.4.1.6527.3.1.2.8.13.1.12
The value of vRtrLdpAddrFecInLabelIfIndex2 specifies the interface index for ingress label 2
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpAddrFecInLabel3 1.3.6.1.4.1.6527.3.1.2.8.13.1.13
The value of vRtrLdpAddrFecInLabel3 specifies the third ingress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecInLabelStatus3 1.3.6.1.4.1.6527.3.1.2.8.13.1.14
The value of vRtrLdpAddrFecInLabelStatus3 specifies the status of the ingress label 3
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpAddrFecInLabelIfIndex3 1.3.6.1.4.1.6527.3.1.2.8.13.1.15
The value of vRtrLdpAddrFecInLabelIfIndex3 specifies the interface index for ingress label 3
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpAddrFecInLabel4 1.3.6.1.4.1.6527.3.1.2.8.13.1.16
The value of vRtrLdpAddrFecInLabel4 specifies the fourth ingress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecInLabelStatus4 1.3.6.1.4.1.6527.3.1.2.8.13.1.17
The value of vRtrLdpAddrFecInLabelStatus4 specifies the status of the ingress label 4
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpAddrFecInLabelIfIndex4 1.3.6.1.4.1.6527.3.1.2.8.13.1.18
The value of vRtrLdpAddrFecInLabelIfIndex4 specifies the interface index for ingress label 4
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpAddrFecInLabel5 1.3.6.1.4.1.6527.3.1.2.8.13.1.19
The value of vRtrLdpAddrFecInLabel5 specifies the fifth ingress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecInLabelStatus5 1.3.6.1.4.1.6527.3.1.2.8.13.1.20
The value of vRtrLdpAddrFecInLabelStatus5 specifies the status of the ingress label 5
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpAddrFecInLabelIfIndex5 1.3.6.1.4.1.6527.3.1.2.8.13.1.21
The value of vRtrLdpAddrFecInLabelIfIndex5 specifies the interface index for ingress label 5
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpAddrFecOutLabel1 1.3.6.1.4.1.6527.3.1.2.8.13.1.22
The value of vRtrLdpAddrFecOutLabel1 specifies the first egress label exchanged
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecOutLabelStatus1 1.3.6.1.4.1.6527.3.1.2.8.13.1.23
The value of vRtrLdpAddrFecOutLabelStatus1 specifies the status of the egress label 1
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpAddrFecOutLabelIfIndex1 1.3.6.1.4.1.6527.3.1.2.8.13.1.24
The value of vRtrLdpAddrFecOutLabelIfIndex1 specifies the interface index for egress label 1
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpAddrFecOutLabelNextHop1 1.3.6.1.4.1.6527.3.1.2.8.13.1.25
The value of vRtrLdpAddrFecOutLabelNextHop1 specifies the IP address of the next hop for egress label 1
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpAddrFecOutLabel2 1.3.6.1.4.1.6527.3.1.2.8.13.1.26
The value of vRtrLdpAddrFecOutLabel2 specifies the second egress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecOutLabelStatus2 1.3.6.1.4.1.6527.3.1.2.8.13.1.27
The value of vRtrLdpAddrFecOutLabelStatus2 specifies the status of the egress label 2
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpAddrFecOutLabelIfIndex2 1.3.6.1.4.1.6527.3.1.2.8.13.1.28
The value of vRtrLdpAddrFecOutLabelIfIndex2 specifies the interface index for egress label 2
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpAddrFecOutLabelNextHop2 1.3.6.1.4.1.6527.3.1.2.8.13.1.29
The value of vRtrLdpAddrFecOutLabelNextHop2 specifies the IP address of the next hop for egress label 2
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpAddrFecOutLabel3 1.3.6.1.4.1.6527.3.1.2.8.13.1.30
The value of vRtrLdpAddrFecOutLabel3 specifies the third egress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecOutLabelStatus3 1.3.6.1.4.1.6527.3.1.2.8.13.1.31
The value of vRtrLdpAddrFecOutLabelStatus3 specifies the status of the egress label 3
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpAddrFecOutLabelIfIndex3 1.3.6.1.4.1.6527.3.1.2.8.13.1.32
The value of vRtrLdpAddrFecOutLabelIfIndex3 specifies the interface index for egress label 3
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpAddrFecOutLabelNextHop3 1.3.6.1.4.1.6527.3.1.2.8.13.1.33
The value of vRtrLdpAddrFecOutLabelNextHop3 specifies the IP address of the next hop for egress label 3
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpAddrFecOutLabel4 1.3.6.1.4.1.6527.3.1.2.8.13.1.34
The value of vRtrLdpAddrFecOutLabel4 specifies the fourth egress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecOutLabelStatus4 1.3.6.1.4.1.6527.3.1.2.8.13.1.35
The value of vRtrLdpAddrFecOutLabelStatus4 specifies the status of the egress label 4
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpAddrFecOutLabelIfIndex4 1.3.6.1.4.1.6527.3.1.2.8.13.1.36
The value of vRtrLdpAddrFecOutLabelIfIndex4 specifies the interface index for egress label 4
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpAddrFecOutLabelNextHop4 1.3.6.1.4.1.6527.3.1.2.8.13.1.37
The value of vRtrLdpAddrFecOutLabelNextHop4 specifies the IP address of the next hop for egress label 4
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpAddrFecOutLabel5 1.3.6.1.4.1.6527.3.1.2.8.13.1.38
The value of vRtrLdpAddrFecOutLabel5 specifies the fifth egress label (if at all) exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAddrFecOutLabelStatus5 1.3.6.1.4.1.6527.3.1.2.8.13.1.39
The value of vRtrLdpAddrFecOutLabelStatus5 specifies the status of the egress label 5
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vRtrLdpAddrFecOutLabelIfIndex5 1.3.6.1.4.1.6527.3.1.2.8.13.1.40
The value of vRtrLdpAddrFecOutLabelIfIndex5 specifies the interface index for egress label 5
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

vRtrLdpAddrFecOutLabelNextHop5 1.3.6.1.4.1.6527.3.1.2.8.13.1.41
The value of vRtrLdpAddrFecOutLabelNextHop5 specifies the IP address of the next hop for egress label 5
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpAddrFecLspId 1.3.6.1.4.1.6527.3.1.2.8.13.1.42
The value of vRtrLdpAddrFecLspId indicates the LSP id of the LSP associated with the specified service FEC.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxVRtrMplsLspID  

vRtrLdpAddrFecMapTable 1.3.6.1.4.1.6527.3.1.2.8.14
vRtrLdpAddrFecMapTable is a read-only table which maps to the vRtrLdpAddrFecTable. This table has the same indexes as the vRtrLdpAddrFecTable but the order in which these indexes are specified is different for the two tables.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpAddrFecMapEntry

vRtrLdpAddrFecMapEntry 1.3.6.1.4.1.6527.3.1.2.8.14.1
Each row entry represents an instance of an address FEC sent to or received from an LDP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpAddrFecMapEntry  

vRtrLdpAddrFecMapFecType 1.3.6.1.4.1.6527.3.1.2.8.14.1.1
The value of vRtrLdpAddrFecMapFecType specifies the FEC type.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpFECType  

vRtrLdpAddrFecMapIpPrefix 1.3.6.1.4.1.6527.3.1.2.8.14.1.2
The value of vRtrLdpAddrFecMapIpPrefix specifies the IP Address Prefix for this address FEC.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpAddrFecMapIpMask 1.3.6.1.4.1.6527.3.1.2.8.14.1.3
The value of vRtrLdpAddrFecMapIpMask specifies the IP Address Mask for this address FEC.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

vRtrLdpAdjBackoffTable 1.3.6.1.4.1.6527.3.1.2.8.15
vRtrLdpAdjBackoffTable is a read-only table which augments the vRtrLdpHelloAdjTable. The purpose of this table is to keep backoff information about the LDP Hello Adjacencies on the virtual router. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpHelloAdjTable, and the augmenting table vRtrLdpAdjBackoffTable. This in effect extends the vRtrLdpHelloAdjTable with additional columns. Creation or deletion of a row in the vRtrLdpHelloAdjTable results in the same fate for the row in the vRtrLdpAdjBackoffTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpAdjBackoffEntry

vRtrLdpAdjBackoffEntry 1.3.6.1.4.1.6527.3.1.2.8.15.1
A row in this table contains backoff information about an LDP adjacency. When an LDP session startup fails for the first time, the LDP entity waits for a certain time interval before it tries to setup the session again. This interval is the backoff interval. The initial value for the backoff interval is set to the value of vRtrLdpAdjInitBackoff. After waiting for the backoff interval, LDP retries to setup the LDP session. If it fails again the backoff interval increases exponentially and this repeats for each successive LDP session startup failure. If the backoff interval exceeds vRtrLdpAdjMaxBackoff, LDP will not backoff anymore and will give up trying to establish the LDP session.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpAdjBackoffEntry  

vRtrLdpAdjInitBackoff 1.3.6.1.4.1.6527.3.1.2.8.15.1.1
The value of vRtrLdpAdjInitBackoff specifies the initial backoff time. After a LDP session setup has failed, the value of vRtrLdpAdjInitBackoff is the time interval, in seconds, that the LDP entity waits before attempting to setup the session again. This interval is the backoff interval. This variable indicates the initial value for backoff interval when the LDP session startup first fails. Thereafter, if session startup fails again the backoff interval increases exponentially.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..2592000  

vRtrLdpAdjMaxBackoff 1.3.6.1.4.1.6527.3.1.2.8.15.1.2
The value of vRtrLdpAdjMaxBackoff specifies the maximum backoff time. For each successive failure of the LDP session startup, the backoff interval (the time for which the router waits before retrying) increases exponentially. If the backoff interval exceeds vRtrLdpAdjMaxBackoff, the router will not backoff anymore and will give up trying to establish the LDP session. A value of 0 for vRtrLdpAdjMaxBackoff indicates that the backoff interval remains constant and will not increase exponentially. In effect the router will try to establish an LDP session till it succeeds
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..2592000  

vRtrLdpAdjCurrentBackoff 1.3.6.1.4.1.6527.3.1.2.8.15.1.3
This value of vRtrLdpAdjCurrentBackoff specifies the current value of the backoff interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAdjWaitingTime 1.3.6.1.4.1.6527.3.1.2.8.15.1.4
The value of vRtrLdpAdjWaitingTime specifies the time for which the entity has been waiting in backoff state.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpAdjBackoffStatus 1.3.6.1.4.1.6527.3.1.2.8.15.1.5
The value of vRtrLdpAdjBackoffStatus indicates whether or not the entity is in backoff state. If this value is 'true', then the entity is in a backoff state and if the value is 'false' then the entity is not in a backoff state
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vRtrLdpPeerParamsTable 1.3.6.1.4.1.6527.3.1.2.8.16
vRtrLdpPeerParamsTable has an entry for an LDP peer. This table is used to configure parmaters specific to the peer whether it is an interface or a targeted peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpPeerParamsEntry

vRtrLdpPeerParamsEntry 1.3.6.1.4.1.6527.3.1.2.8.16.1
Each row entry represents a peer that participates in the LDP protocol on this virtual router. Row entries can be created or deleted via SNMP SET requests. A row with default attribute values is created by setting vRtrLdpPeerRowStatus to 'createAndGo'. A row entry can be destroyed by setting vRtrLdpPeerRowStatus to 'destroy'. A row entry with vRtrLdpPeerAddress of 0.0.0.0 represents the default LDP parameters used for all peers that do not have a corresponding entry in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpPeerParamsEntry  

vRtrLdpPeerRowStatus 1.3.6.1.4.1.6527.3.1.2.8.16.1.1
vRtrLdpPeerRowStatus is used to control the creation and deletion of rows in the vRtrLdpPeerParamsTable. A row can be created by setting vRtrLdpPeerRowStatus to 'createAndGo'. The agent should assign the default attribute values and change the row status to 'active'. A row entry can be destroyed by setting vRtrLdpPeerRowStatus to 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vRtrLdpPeerAuth 1.3.6.1.4.1.6527.3.1.2.8.16.1.2
When the value of vRtrLdpPeerAuth is 'true', authentication using MD5 message based digest protocol is enabled. When 'false', no authentication is used.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vRtrLdpPeerAuthKey 1.3.6.1.4.1.6527.3.1.2.8.16.1.3
The string specified in vRtrLdpPeerAuthKey is the authentication key to be used between LDP neighbors before establishing sessions. Authentication is done using the MD-5 message based digest protocol. The authentication key can be any combination of letters or numbers. Note that the string may contain embedded nulls. An SNMP Get request on this object should return an OCTET STRING of length 0.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(0..16)  

vRtrLdpPeerMinTTLValue 1.3.6.1.4.1.6527.3.1.2.8.16.1.4
The value of vRtrLdpPeerMinTTLValue specifies the minimum TTL value for an incoming LDP packet. If vRtrLdpPeerMinTTLValue is set to zero (0), the TTL Security feature is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 1..255  

vRtrLdpPeerTTLLogId 1.3.6.1.4.1.6527.3.1.2.8.16.1.5
The value of vRtrLdpPeerTTLLogId specifies the filter log to use for packets that fail TTL security check. The value zero indicates that logging is disabled.
Status: current Access: read-create
OBJECT-TYPE    
  TFilterLogId  

vRtrLdpPeerAuthKeyChain 1.3.6.1.4.1.6527.3.1.2.8.16.1.6
The value of vRtrLdpPeerAuthKeyChain specifies the keychain which will be used to sign and/or authenticate the BGP protocol stream. The keychain name is defined by tmnxKeyChainName and is the index for TIMETRA-SECURITY-MIB::tmnxKeyChainTable
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

vRtrLdpStaticFecTable 1.3.6.1.4.1.6527.3.1.2.8.18
vRtrLdpStaticFecTable has an entry for each static prefix FEC configured on the virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpStaticFecEntry

vRtrLdpStaticFecEntry 1.3.6.1.4.1.6527.3.1.2.8.18.1
Each row entry represents a static prefix FEC configured on the virtual router. Entries can be created and deleted via SNMP SET operations to vRtrLdpStaticFecRowStatus. An entry is created by setting vRtrLdpStaticFecRowStatus to 'createAndWait'. The row status can be set to 'active' only after a next-hop entry corresponding to this prefix has been created in the vRtrLdpStaticFecNHTable. An entry is deleted by setting vRtrLdpStaticFecRowStatus to 'destroy'. For deletion to succeed, there must be no next-hop entries corresponding to this prefix in the vRtrLdpStaticFecNHTable i.e. vRtrLdpStaticFecNumNH must have a value of 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpStaticFecEntry  

vRtrLdpStaticFecIpPrefix 1.3.6.1.4.1.6527.3.1.2.8.18.1.1
The value of vRtrLdpStaticFecIpPrefix specifies the IP Address Prefix for this static FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

vRtrLdpStaticFecIpMask 1.3.6.1.4.1.6527.3.1.2.8.18.1.2
The value of vRtrLdpStaticFecIpMask specifies the IP Address Mask for this static FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

vRtrLdpStaticFecRowStatus 1.3.6.1.4.1.6527.3.1.2.8.18.1.3
vRtrLdpStaticFecRowStatus is used to create, delete or control entries in the vRtrLdpStaticFecTable. To create a row entry, set vRtrLdpStaticFecRowStatus to 'createAndWait'. Before the row can be placed in the 'active' state, a next-hop entry corresponding to this prefix must exist in the vRtrLdpStaticFecNHTable. To delete a row entry, set vRtrLdpStaticFecRowStatus to 'destroy'. For deletion to succeed, no next-hop entry corresponding to this prefix must exist in the vRtrLdpStaticFecNHTable i.e. vRtrLdpStaticFecNumNH must have a value of 0.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vRtrLdpStaticFecNextNHIndex 1.3.6.1.4.1.6527.3.1.2.8.18.1.4
The value of vRtrLdpStaticFecNextNHIndex is used to assign values to vRtrLdpStaticFecNHIndex when creating rows in the vRtrLdpStaticFecNHTable. The network manager reads this object and uses it in the SET request that creates a new row entry in the vRtrLdpStaticFecNHTable. If the SET fails with the code 'inconsistentValue', the process must be repeated. If the SET succeeds, then this object will be incremented and the new instance is created according to the manager's directions.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpStaticFecIngLabel 1.3.6.1.4.1.6527.3.1.2.8.18.1.5
The value of vRtrLdpStaticFecIngLabel specifies the label that is advertised to the upstream peer. If this variable is set to the default value of 4294967295, the ingress label will be dynamically assigned by the label manager.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 32..1023 | 4294967295  

vRtrLdpStaticFecNumNH 1.3.6.1.4.1.6527.3.1.2.8.18.1.6
The value of vRtrLdpStaticFecNumNH specifies the number of next-hops that are associated with the static prefix FEC represented by this row entry. This is also the number of row entries configured in the vRtrLdpStaticFecNHTable for this static prefix FEC. If the static FEC has no next-hops associated with it, this value will be 0 and the row entry will be placed in the 'notReady' state. Deletion of the row entry will be allowed only if vRtrLdpStaticFecNumNH is 0.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vRtrLdpStaticFecOperIngLabel 1.3.6.1.4.1.6527.3.1.2.8.18.1.7
The value of vRtrLdpStaticFecOperIngLabel specifies the actual or operational value of the label that was advertised to the upstream peer.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpStaticFecNHTable 1.3.6.1.4.1.6527.3.1.2.8.19
vRtrLdpStaticFecNHTable has an entry for each next-hop configured for a static prefix FEC on the virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpStaticFecNHEntry

vRtrLdpStaticFecNHEntry 1.3.6.1.4.1.6527.3.1.2.8.19.1
Each row entry represents a next-hop configured for a static prefix FEC on the virtual router. The static prefix FEC corresponding to a next-hop entry must exist as a row entry in the vRtrLdpStaticFecTable. Entries can be created and deleted via SNMP SET operations to vRtrLdpStaticFecNHRowStatus. An entry is created by setting vRtrLdpStaticFecNHRowStatus to 'createAndWait' or 'createAndGo'. Before the row can be placed in the 'active' state, vRtrLdpStaticFecNHType must be set to a valid value. An entry is deleted by setting vRtrLdpStaticFecNHRowStatus to 'destroy'.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpStaticFecNHEntry  

vRtrLdpStaticFecNHIndex 1.3.6.1.4.1.6527.3.1.2.8.19.1.1
The value of vRtrLdpStaticFecNHIndex is used to identify the next-hop associated with a static prefix FEC. This value is unique amongst next-hop entries for the same static prefix FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

vRtrLdpStaticFecNHRowStatus 1.3.6.1.4.1.6527.3.1.2.8.19.1.2
vRtrLdpStaticFecNHRowStatus is used to create, delete or control entries in the vRtrLdpStaticFecNHTable. An entry is created by setting vRtrLdpStaticFecNHRowStatus to 'createAndWait' or 'createAndGo'. Before the row can be placed in the 'active' state, vRtrLdpStaticFecNHType must be set to a valid value. An entry is deleted by setting vRtrLdpStaticFecNHRowStatus to 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vRtrLdpStaticFecNHType 1.3.6.1.4.1.6527.3.1.2.8.19.1.3
The value of vRtrLdpStaticFecNHType specifies the type of next-hop represented by this row entry. unknown (0) - the next-hop type has not been set. ipAddress (1) - the next-hop is an IP address. pop (2) - there is no next-hop i.e. pop the label and route
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER unknown(0), ipAddress(1), pop(2)  

vRtrLdpStaticFecNHIpAddr 1.3.6.1.4.1.6527.3.1.2.8.19.1.4
If vRtrLdpStaticFecNHType is set to 'ipAddress', the value of vRtrLdpStaticFecNHIpAddr specifies the IP address of the next-hop. In this case, this variable must be set to a valid value before the row be placed in an active state. If vRtrLdpStaticFecNHType is set to 'pop', this value of vRtrLdpStaticFecNHIpAddr will be 0.0.0.0
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

vRtrLdpStaticFecNHEgrLabel 1.3.6.1.4.1.6527.3.1.2.8.19.1.5
The value of vRtrLdpStaticFecNHEgrLabel specifies the egress label associated with this next-hop entry. The LSR will swap the incoming label with the configured egress label. If this egress label has a value of 4294967295, the LSR will pop the incoming label.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 16..1048575 | 4294967295  

vRtrLdpTargTable 1.3.6.1.4.1.6527.3.1.2.8.20
vRtrLdpTargTable keeps information about the export and import prefixes for a targeted LDP session. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpGeneralTable, and the augmenting table, vRtrLdpTargTable. This in effect extends the vRtrLdpGeneralTable with additional columns. Creation or deletion of a row in the vRtrLdpGeneralTable results in the same fate for the row in the vRtrLdpTargTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpTargEntry

vRtrLdpTargEntry 1.3.6.1.4.1.6527.3.1.2.8.20.1
A row in this table represents information about the targeted LDP session.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpTargEntry  

vRtrLdpTargImportPolicy1 1.3.6.1.4.1.6527.3.1.2.8.20.1.3
The value of vRtrLdpTargImportPolicy1 specifies the import route policy to determine which routes are accepted from targeted LDP neighbors. A maximum of 5 policies can be specified. vRtrLdpTargImportPolicy1 specifies the first policy.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpTargImportPolicy2 1.3.6.1.4.1.6527.3.1.2.8.20.1.4
The value of vRtrLdpTargImportPolicy2 specifies the second import policy used to determine which routes are accepted from targeted LDP neighbors.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpTargImportPolicy3 1.3.6.1.4.1.6527.3.1.2.8.20.1.5
The value of vRtrLdpTargImportPolicy3 specifies the third import policy used to determine which routes are accepted from targeted LDP neighbors.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpTargImportPolicy4 1.3.6.1.4.1.6527.3.1.2.8.20.1.6
The value of vRtrLdpTargImportPolicy4 specifies the fourth import policy to determine which routes are accepted from targeted LDP neighbors.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpTargImportPolicy5 1.3.6.1.4.1.6527.3.1.2.8.20.1.7
The value of vRtrLdpTargImportPolicy5 specifies the fifth import policy used to determine which routes are accepted from targeted LDP neighbors.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpTargExportPolicy1 1.3.6.1.4.1.6527.3.1.2.8.20.1.8
The value of vRtrLdpTargExportPolicy1 specifies the export route policy used to determine which routes are exported to this targeted LDP session. A maximum of 5 policies can be specified. vRtrLdpTargExportPolicy1 specifies the first policy.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpTargExportPolicy2 1.3.6.1.4.1.6527.3.1.2.8.20.1.9
The value of vRtrLdpTargExportPolicy2 specifies the second export policy used to determine which routes are exported to this targeted LDP session
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpTargExportPolicy3 1.3.6.1.4.1.6527.3.1.2.8.20.1.10
The value of vRtrLdpTargExportPolicy3 specifies the third export policy used to determine which routes are exported to this targeted LDP session.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpTargExportPolicy4 1.3.6.1.4.1.6527.3.1.2.8.20.1.11
The value of vRtrLdpTargExportPolicy4 specifies the fourth export policy used to determine which routes are exported to this targeted LDP session.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpTargExportPolicy5 1.3.6.1.4.1.6527.3.1.2.8.20.1.12
The value of vRtrLdpTargExportPolicy5 specifies the fifth export policy used to determine which routes are exported to this targeted LDP session.
Status: current Access: read-create
OBJECT-TYPE    
  TPolicyStatementNameOrEmpty  

vRtrLdpTargTunnelPreference 1.3.6.1.4.1.6527.3.1.2.8.20.1.13
The value of vRtrLdpTargTunnelPreference indicates whether LDP over tunnel is preferred when link-level LDP bindings are also available. If this value is 'true', then LDP tunnels are preferred and if the value is 'false' then LDP over tunnel is preferred. By default LDP tunnels are preferred.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vRtrLdpIfTunnelingLspTable 1.3.6.1.4.1.6527.3.1.2.8.21
vRtrLdpIfTunnelingLspTable keeps the list of LDP-over-RSVP LSP ids which are currently supported by the application. Each LSP ID in the list corresponds to the vRtrMplsLspIndex of the given MPLS LSP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpIfTunnelingLspEntry

vRtrLdpIfTunnelingLspEntry 1.3.6.1.4.1.6527.3.1.2.8.21.1
A row in this table contains the LSP id information about an LDP interface or targeted peer. Row entries can be created or deleted via SNMP SET requests. A row is created by setting vRtrLdpIfLspRowStatus to 'createAndGo' provided the corresponding LSP id exists as an MPLS lsp. A row entry can be destroyed by setting vRtrLdpIfLspRowStatus to 'destroy'.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpIfTunnelingLspEntry  

vRtrLdpIfLspId 1.3.6.1.4.1.6527.3.1.2.8.21.1.1
The value of vRtrLdpIfLspId specifies the LSP id of the LSP associated with the specified interface or targeted peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxVRtrMplsLspID  

vRtrLdpIfLspRowStatus 1.3.6.1.4.1.6527.3.1.2.8.21.1.2
vRtrLdpIfLspRowStatus is used to create, delete or control entries in the vRtrLdpIfTunnelingLspTable. An entry is created by setting vRtrLdpIfLspRowStatus to 'createAndGo'. An entry is deleted by setting vRtrLdpIfLspRowStatus to 'destroy'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vRtrLdpCepTdmFecTable 1.3.6.1.4.1.6527.3.1.2.8.22
vRtrLdpCepTdmFecTable is a read-only table that represents all CEP/TDM FECs either sent to or received from an LDP peer known to the Virtual Router. The CEP/TDM Sub-TLVs are defined in RFC 4446: Parameter Id Description 0x04 CEP/TDM Payload Bytes 0x07 CEP/TDM bit-rate 0x0B TDM Options.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VRtrLdpCepTdmFecEntry

vRtrLdpCepTdmFecEntry 1.3.6.1.4.1.6527.3.1.2.8.22.1
Each row entry represents an instance of a service FEC sent to or received from an LDP peer. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpServFecTable, and the augmenting table, vRtrLdpCepTdmFecTable. This in effect extends the vRtrLdpServFecTable with additional columns. Creation or deletion of a row in the vRtrLdpServFecTable results in the same fate for the row in the VRtrLdpCepTdmFecEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  VRtrLdpCepTdmFecEntry  

vRtrLdpCepTdmLocalPayloadSize 1.3.6.1.4.1.6527.3.1.2.8.22.1.4
The value of vRtrLdpCepTdmLocalPayloadSize indicates the local payload size.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpCepTdmRemotePayloadSize 1.3.6.1.4.1.6527.3.1.2.8.22.1.5
The value of vRtrLdpCepTdmRemotePayloadSize indicates the remote payload size.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpCepTdmLocalBitrate 1.3.6.1.4.1.6527.3.1.2.8.22.1.6
The value of vRtrLdpCepTdmLocalBitrate indicates the local bitrate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpCepTdmRemoteBitrate 1.3.6.1.4.1.6527.3.1.2.8.22.1.7
The value of vRtrLdpCepTdmRemoteBitrate indicates the remote bitrate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpCepTdmLocalRtpHeader 1.3.6.1.4.1.6527.3.1.2.8.22.1.8
The value of vRtrLdpCepTdmLocalRtpHeader indicates the local RTP header usage bit.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vRtrLdpCepTdmRemoteRtpHeader 1.3.6.1.4.1.6527.3.1.2.8.22.1.9
The value of vRtrLdpCepTdmRemoteRtpHeader indicates the remote RTP header usage bit.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vRtrLdpCepTdmLocalDiffTimestamp 1.3.6.1.4.1.6527.3.1.2.8.22.1.10
The value of vRtrLdpCepTdmLocalDiffTimestamp indicates the local differential (or dynamic) timestamping mode bit.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vRtrLdpCepTdmRemoteDiffTimestamp 1.3.6.1.4.1.6527.3.1.2.8.22.1.11
The value of vRtrLdpCepTdmRemoteDiffTimestamp indicates the remote differential (or dynamic) timestamping mode bit.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vRtrLdpCepTdmLocalSigPkts 1.3.6.1.4.1.6527.3.1.2.8.22.1.12
The value of vRtrLdpCepTdmLocalSigPkts indicates the local CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsSigPkts  

vRtrLdpCepTdmRemoteSigPkts 1.3.6.1.4.1.6527.3.1.2.8.22.1.13
The value of vRtrLdpCepTdmRemoteSigPkts indicates the remote CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsSigPkts  

vRtrLdpCepTdmLocalCasTrunk 1.3.6.1.4.1.6527.3.1.2.8.22.1.14
The value of vRtrLdpCepTdmLocalCasTrunk indicates the local CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsCasTrunkFraming  

vRtrLdpCepTdmRemoteCasTrunk 1.3.6.1.4.1.6527.3.1.2.8.22.1.15
The value of vRtrLdpCepTdmRemoteCasTrunk indicates the remote CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsCasTrunkFraming  

vRtrLdpCepTdmLocalTimestampFreq 1.3.6.1.4.1.6527.3.1.2.8.22.1.16
The value of vRtrLdpCepTdmLocalTimestampFreq indicates the local CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpCepTdmRemoteTimestampFreq 1.3.6.1.4.1.6527.3.1.2.8.22.1.17
The value of vRtrLdpCepTdmRemoteTimestampFreq indicates the remote CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpCepTdmLocalPayloadType 1.3.6.1.4.1.6527.3.1.2.8.22.1.18
The value of vRtrLdpCepTdmLocalPayloadType indicates the local payload type.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpCepTdmRemotePayloadType 1.3.6.1.4.1.6527.3.1.2.8.22.1.19
The value of vRtrLdpCepTdmRemotePayloadType indicates the remote payload type.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpCepTdmLocalSsrcId 1.3.6.1.4.1.6527.3.1.2.8.22.1.20
The value of vRtrLdpCepTdmLocalSsrcId indicates the local value of SSRC ID.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vRtrLdpCepTdmRemoteSsrcId 1.3.6.1.4.1.6527.3.1.2.8.22.1.21
The value of vRtrLdpCepTdmRemoteSsrcId indicates the remote value of SSRC ID.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129Table 1.3.6.1.4.1.6527.3.1.2.8.23
vLdpServFec129Table is a read-only table that represents all service FEC-129s either sent to or received from an LDP peer known to the Virtual Router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VLdpServFec129Entry

vLdpServFec129Entry 1.3.6.1.4.1.6527.3.1.2.8.23.1
Each row entry represents an instance of a service FEC-129 sent to or received from an LDP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  VLdpServFec129Entry  

vLdpServFec129AgiTlv 1.3.6.1.4.1.6527.3.1.2.8.23.1.1
The value of vLdpServFec129AgiTlv specifies the Attachment Group Identifier TLV associated with this service FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxLdpFec129Tlv  

vLdpServFec129SrcAiiTlv 1.3.6.1.4.1.6527.3.1.2.8.23.1.2
The value of vLdpServFec129SrcAiiTlv specifies the Source Attachment Individual Identifier TLV associated with this service FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxLdpFec129Tlv  

vLdpServFec129TgtAiiTlv 1.3.6.1.4.1.6527.3.1.2.8.23.1.3
The value of vLdpServFec129TgtAiiTlv specifies the Target Attachment Individual Identifier TLV associated with this service FEC.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxLdpFec129Tlv  

vLdpServFec129ServType 1.3.6.1.4.1.6527.3.1.2.8.23.1.4
The value of vLdpServFec129ServType specifies the Service type associated with this service FEC.
Status: current Access: read-only
OBJECT-TYPE    
  ServType  

vLdpServFec129ServId 1.3.6.1.4.1.6527.3.1.2.8.23.1.5
The value of vLdpServFec129ServId specifies the Service identifier associated with this service FEC.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxServId 1..2147483647  

vLdpServFec129VpnId 1.3.6.1.4.1.6527.3.1.2.8.23.1.6
The value of vLdpServFec129VpnId identifies the VPN associated with the FEC.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxVpnId  

vLdpServFec129Flags 1.3.6.1.4.1.6527.3.1.2.8.23.1.7
The bit flags of vLdpServFec129Flags specify the characteristics of the FEC.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLdpFECFlags  

vLdpServFec129NumInLabels 1.3.6.1.4.1.6527.3.1.2.8.23.1.8
The value of vLdpServFec129NumInLabels gives the number of labels that have been sent to the peer associated with this FEC. This value also indicates whether vLdpServFec129InLabel1 entry contain valid information i.e. if the value of vLdpServFec129NumInLabels is 1 then vLdpServFec129InLabel1 will contain valid label information.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129NumOutLabels 1.3.6.1.4.1.6527.3.1.2.8.23.1.9
The value of vLdpServFec129NumOutLabels gives the number of labels that have been received from the peer associated with this FEC. This value also indicates whether vLdpServFec129OutLabel1 entry contain valid information i.e. if the value of vLdpServFec129NumOutLabels is 1, then vLdpServFec129OutLabel1 will contain valid label information.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129InLabel1 1.3.6.1.4.1.6527.3.1.2.8.23.1.10
The value of vLdpServFec129InLabel1 specifies the first ingress label exchanged
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129InLabelStatus1 1.3.6.1.4.1.6527.3.1.2.8.23.1.11
The value of vLdpServFec129InLabelStatus1 specifies the status of the ingress label 1
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vLdpServFec129OutLabel1 1.3.6.1.4.1.6527.3.1.2.8.23.1.20
The value of vLdpServFec129OutLabel1 specifies the first egress label exchanged.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129OutLabelStatus1 1.3.6.1.4.1.6527.3.1.2.8.23.1.21
The value of vLdpServFec129OutLabelStatus1 specifies the status of the egress label 1
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelStatus  

vLdpServFec129SdpId 1.3.6.1.4.1.6527.3.1.2.8.23.1.22
The value of vLdpServFec129SdpId identifies the SDP associated with this peer.
Status: current Access: read-only
OBJECT-TYPE    
  SdpId  

vLdpServFec129LocalMTU 1.3.6.1.4.1.6527.3.1.2.8.23.1.23
The value of vLdpServFec129LocalMTU specifies the largest service frame size (in octets) that can be handled by the local ESR.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129RemoteMTU 1.3.6.1.4.1.6527.3.1.2.8.23.1.24
The value of vLdpServFec129RemoteMTU specifies the largest service frame size (in octets) that can be handled by the remote ESR.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129LocalVlanTag 1.3.6.1.4.1.6527.3.1.2.8.23.1.25
The value of vLdpServFec129LocalVlanTag specifies the local tag on a VLAN VC type SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129RemoteVlanTag 1.3.6.1.4.1.6527.3.1.2.8.23.1.26
The value of vLdpServFec129RemoteVlanTag specifies the remote tag on a VLAN VC type SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129LocalMaxCellConcat 1.3.6.1.4.1.6527.3.1.2.8.23.1.27
The value of vLdpServFec129LocalMaxCellConcat specifies the local maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129RemoteMaxCellConcat 1.3.6.1.4.1.6527.3.1.2.8.23.1.28
The value of vLdpServFec129RemoteMaxCellConcat specifies the remote maximum number of ATM cells to concatenate on a ATM cell-mode VC type SDP binding.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpServFec129InLabelSigStatus1 1.3.6.1.4.1.6527.3.1.2.8.23.1.29
The value of vLdpServFec129InLabelSigStatus1 indicates the signaling status for vLdpServFec129InLabel1.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vLdpServFec129OutLabelSigStatus1 1.3.6.1.4.1.6527.3.1.2.8.23.1.30
The value of vLdpServFec129OutLabelSigStatus1 indicates the signaling status for vLdpServFec129OutLabel1.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxLabelSigStatus  

vLdpServFec129MapTable 1.3.6.1.4.1.6527.3.1.2.8.24
vLdpServFec129MapTable is a read-only table which maps to the vLdpServFec129Table. This table has the same indexes as the vLdpServFec129Table but the order in which these indexes are specified is different for the two tables.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VLdpServFec129MapEntry

vLdpServFec129MapEntry 1.3.6.1.4.1.6527.3.1.2.8.24.1
Each row entry represents an instance of a service FEC sent to or received from an LDP peer.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  VLdpServFec129MapEntry  

vLdpServFec129MapVcType 1.3.6.1.4.1.6527.3.1.2.8.24.1.1
The value of vLdpServFec129MapVcType specifies the VC type associated with this service FEC.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxVcType  

vLdpServFec129MapAgiTlv 1.3.6.1.4.1.6527.3.1.2.8.24.1.2
The value of vLdpServFec129MapAgiTlv specifies the Attachment Group Identifier TLV associated with this service FEC.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxLdpFec129Tlv  

vLdpServFec129MapSrcAiiTlv 1.3.6.1.4.1.6527.3.1.2.8.24.1.3
The value of vLdpServFec129MapSrcAiiTlv specifies the Source Attachment Individual Identifier TLV associated with this service FEC.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxLdpFec129Tlv  

vLdpServFec129MapTgtAiiTlv 1.3.6.1.4.1.6527.3.1.2.8.24.1.4
The value of vLdpServFec129MapTgtAiiTlv specifies the Target Attachment Individual Identifier TLV associated with this service FEC.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxLdpFec129Tlv  

vLdpCepTdmFec129Table 1.3.6.1.4.1.6527.3.1.2.8.25
vLdpCepTdmFec129Table is a read-only table that represents all CEP/TDM FECs either sent to or received from an LDP peer known to the Virtual Router. The CEP/TDM Sub-TLVs are defined in RFC 4446: Parameter Id Description 0x04 CEP/TDM Payload Bytes 0x07 CEP/TDM bit-rate 0x0B TDM Options.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VLdpCepTdmFec129Entry

vLdpCepTdmFec129Entry 1.3.6.1.4.1.6527.3.1.2.8.25.1
Each row entry represents an instance of a service FEC sent to or received from an LDP peer. Use of AUGMENTS clause implies a one-to-one dependent relationship between the base table, vRtrLdpServFecTable, and the augmenting table, vLdpCepTdmFec129Table. This in effect extends the vRtrLdpServFecTable with additional columns. Creation or deletion of a row in the vRtrLdpServFecTable results in the same fate for the row in the VLdpCepTdmFec129Entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  VLdpCepTdmFec129Entry  

vLdpCepTdmFec129LocalPayloadSize 1.3.6.1.4.1.6527.3.1.2.8.25.1.4
The value of vLdpCepTdmFec129LocalPayloadSize indicates the local payload size.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpCepTdmFec129RemotePayloadSize 1.3.6.1.4.1.6527.3.1.2.8.25.1.5
The value of vLdpCepTdmFec129RemotePayloadSize indicates the remote payload size.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpCepTdmFec129LocalBitrate 1.3.6.1.4.1.6527.3.1.2.8.25.1.6
The value of vLdpCepTdmFec129LocalBitrate indicates the local bitrate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpCepTdmFec129RemoteBitrate 1.3.6.1.4.1.6527.3.1.2.8.25.1.7
The value of vLdpCepTdmFec129RemoteBitrate indicates the remote bitrate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpCepTdmFec129LocalRtpHeader 1.3.6.1.4.1.6527.3.1.2.8.25.1.8
The value of vLdpCepTdmFec129LocalRtpHeader indicates the local RTP header usage bit.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vLdpCepTdmFec129RemoteRtpHeader 1.3.6.1.4.1.6527.3.1.2.8.25.1.9
The value of vLdpCepTdmFec129RemoteRtpHeader indicates the remote RTP header usage bit.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vLdpCepTdmFec129LocalDiffTimestamp 1.3.6.1.4.1.6527.3.1.2.8.25.1.10
The value of vLdpCepTdmFec129LocalDiffTimestamp indicates the local differential (or dynamic) timestamping mode bit.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vLdpCepTdmFec129RemoteDiffTimestamp 1.3.6.1.4.1.6527.3.1.2.8.25.1.11
The value of vLdpCepTdmFec129RemoteDiffTimestamp indicates the remote differential (or dynamic) timestamping mode bit.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vLdpCepTdmFec129LocalSigPkts 1.3.6.1.4.1.6527.3.1.2.8.25.1.12
The value of vLdpCepTdmFec129LocalSigPkts indicates the local CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsSigPkts  

vLdpCepTdmFec129RemoteSigPkts 1.3.6.1.4.1.6527.3.1.2.8.25.1.13
The value of vLdpCepTdmFec129RemoteSigPkts indicates the remote CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsSigPkts  

vLdpCepTdmFec129LocalCasTrunk 1.3.6.1.4.1.6527.3.1.2.8.25.1.14
The value of vLdpCepTdmFec129LocalCasTrunk indicates the local CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsCasTrunkFraming  

vLdpCepTdmFec129RemoteCasTrunk 1.3.6.1.4.1.6527.3.1.2.8.25.1.15
The value of vLdpCepTdmFec129RemoteCasTrunk indicates the remote CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  TdmOptionsCasTrunkFraming  

vLdpCepTdmFec129LocalTimestampFreq 1.3.6.1.4.1.6527.3.1.2.8.25.1.16
The value of vLdpCepTdmFec129LocalTimestampFreq indicates the local CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpCepTdmFec129RemoteTimestampFreq 1.3.6.1.4.1.6527.3.1.2.8.25.1.17
The value of vLdpCepTdmFec129RemoteCasTrunk indicates the remote CE application signalling packets mode.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpCepTdmFec129LocalPayloadType 1.3.6.1.4.1.6527.3.1.2.8.25.1.18
The value of vLdpCepTdmFec129LocalPayloadType indicates the local payload type.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpCepTdmFec129RemotePayloadType 1.3.6.1.4.1.6527.3.1.2.8.25.1.19
The value of vLdpCepTdmFec129RemotePayloadType indicates the remote payload type.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpCepTdmFec129LocalSsrcId 1.3.6.1.4.1.6527.3.1.2.8.25.1.20
The value of vLdpCepTdmFec129LocalSsrcId indicates the local value of SSRC ID.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vLdpCepTdmFec129RemoteSsrcId 1.3.6.1.4.1.6527.3.1.2.8.25.1.21
The value of vLdpCepTdmFec129RemoteSsrcId indicates the remote value of SSRC ID.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxLdpNotificationObjects 1.3.6.1.4.1.6527.3.1.2.8.17
OBJECT IDENTIFIER    

vRtrLdpInstanceNotifyReasonCode 1.3.6.1.4.1.6527.3.1.2.8.17.1
Used by vRtrLdpInstanceStateChange, the value indicates the reason for the LDP instance state change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER adminUp(1), adminDown(2), operUp(3), operDown(4)  

vRtrLdpIfNotifyReasonCode 1.3.6.1.4.1.6527.3.1.2.8.17.2
Used by vRtrLdpIfStateChange, the value indicates the reason for the LSP interface state change.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER adminUp(1), adminDown(2), operUp(3), operDown(4), sysIpUp(5), sysIpDown(6)  

vRtrLdpNotifyLocalServiceID 1.3.6.1.4.1.6527.3.1.2.8.17.3
Used by vRtrLdpSvcIdMismatch, the value indicates the local Service ID.
Status: obsolete Access: accessible-for-notify
OBJECT-TYPE    
  TmnxServId 1..2147483647  

vRtrLdpNotifyRemoteServiceID 1.3.6.1.4.1.6527.3.1.2.8.17.4
Used by vRtrLdpSvcIdMismatch, the value indicates the remote Service ID.
Status: obsolete Access: accessible-for-notify
OBJECT-TYPE    
  TmnxServId 1..2147483647  

vRtrLdpNotifyLocalGroupID 1.3.6.1.4.1.6527.3.1.2.8.17.5
Used by vRtrLdpGroupIdMismatch, the value indicates the local Group ID.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TmnxVcId  

vRtrLdpNotifyRemoteGroupID 1.3.6.1.4.1.6527.3.1.2.8.17.6
Used by vRtrLdpGroupIdMismatch, the value indicates the remote Group ID.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TmnxVcId  

vRtrLdpStateChange 1.3.6.1.4.1.6527.3.1.3.8.0.1
The vRtrLdpStateChange notification is generated when the LDP protocol is created or deleted in the router.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

vRtrLdpInstanceStateChange 1.3.6.1.4.1.6527.3.1.3.8.0.2
The vRtrLdpInstanceStateChange notification is generated when the LDP module changes state either administratively or operationally.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

vRtrLdpIfStateChange 1.3.6.1.4.1.6527.3.1.3.8.0.3
The vRtrLdpIfStateChange notification is generated when the LDP interface changes state either administratively or operationally.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

vRtrLdpSvcIdMismatch 1.3.6.1.4.1.6527.3.1.3.8.0.4
The vRtrLdpSvcIdMismatch notification is generated when there is a mismatch of local and remote service IDs.
Status: obsolete Access: accessible-for-notify
NOTIFICATION-TYPE    

vRtrLdpGroupIdMismatch 1.3.6.1.4.1.6527.3.1.3.8.0.5
The vRtrLdpGroupIdMismatch notification is generated when there is a mismatch of local and remote group IDs.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

tmnxLdpCompliances 1.3.6.1.4.1.6527.3.1.1.8.1
OBJECT IDENTIFIER    

tmnxLdpGroups 1.3.6.1.4.1.6527.3.1.1.8.2
OBJECT IDENTIFIER    

tmnxLdpV4v0Compliance 1.3.6.1.4.1.6527.3.1.1.8.1.4
The compliance statement for management of extended LDP on Alcatel 7x50 SR series systems 4.0 release.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxLdpV5v0Compliance 1.3.6.1.4.1.6527.3.1.1.8.1.5
The compliance statement for management of extended LDP on Alcatel 7x50 SR series systems 5.0 release.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxLdpV6v0Compliance 1.3.6.1.4.1.6527.3.1.1.8.1.6
The compliance statement for management of extended LDP on Alcatel 7x50 SR series systems 6.0 release.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxLdpAddrFecGroup 1.3.6.1.4.1.6527.3.1.1.8.2.6
The group of objects supporting management of extended LDP address FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpNotifyObjsGroup 1.3.6.1.4.1.6527.3.1.1.8.2.7
The group of objects supporting extended LDP notifications on Alcatel 7x50 SR series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpNotificationGroup 1.3.6.1.4.1.6527.3.1.1.8.2.8
The group of notifications supporting the extended LDP feature on Alcatel 7x50 SR series systems.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

tmnxLdpAdjBackoffGroup 1.3.6.1.4.1.6527.3.1.1.8.2.10
The group of objects supporting general management of extended LDP adjacency backoff on Alcatel 7x50 SR series systems. The vRtrLdpAdjBackoffTable is not yet supported by a TiMOS release.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpObsoleteObjsGroup 1.3.6.1.4.1.6527.3.1.1.8.2.11
The group of obsolete objects for the extended LDP feature on Alcatel 7x50 SR series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpObsoleteNotificationGroup 1.3.6.1.4.1.6527.3.1.1.8.2.12
The group of obsolete notifications for the extended LDP feature on Alcatel 7x50 SR series systems.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

tmnxLdpAdjR2r1Group 1.3.6.1.4.1.6527.3.1.1.8.2.15
The group of objects supporting management of extended LDP Adjacencies for LDP sessions on Alcatel 7x50 SR series systems 2.1 Release.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpSessionR2r1Group 1.3.6.1.4.1.6527.3.1.1.8.2.16
The group of objects supporting management of extended LDP Sessions on Alcatel 7x50 SR series systems 2.1 Release.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpStaticFecV3v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.17
The group of objects supporting management of LDP Static FECs on Alcatel 7x50 SR series systems 3.0 release.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpIfV3v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.19
The group of objects supporting management of extended LDP interfaces and targeted peers on Alcatel 7x50 SR series systems 3.0 release.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpGlobalV3v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.20
The group of objects supporting general management of extended LDP on Alcatel 7x50 SR series systems 3.0 release.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpServFecV4v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.21
The group of objects supporting management of extended LDP service FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems release 4.0.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpGlobalV5v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.22
The group of objects supporting general management of extended LDP on Alcatel 7x50 SR series systems 5.0 release.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpIfV5v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.23
The group of objects supporting management of extended LDP interfaces and targeted peers on Alcatel 7x50 SR series systems 5.0 release.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpServFecV5v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.24
The group of objects supporting management of extended LDP service FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems release 5.0.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpAddrFecV5v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.25
The group of objects supporting management of extended LDP address FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems for release 5.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpSessionV5v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.26
The group of objects supporting management of extended LDP Sessions on Alcatel 7x50 SR series systems 5.0 Release.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpObsoletedV5v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.27
The group of objects obsoleted on Alcatel 7x50 SR series systems 5.0 Release.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpCepTdmFecV6v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.28
The group of objects supporting management of extended LDP CEP/TDM FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems release 6.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpServFecV6v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.29
The group of objects supporting management of extended LDP service FECs sent to or received from an LDP peer on Alcatel 7x50 SR series systems release 6.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpServFec129V6v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.30
The group of objects supporting management of LDP FEC-129s sent to or received from an LDP peer on Alcatel 7x50 SR series systems release 6.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxLdpServFecObsoletedV6v0Group 1.3.6.1.4.1.6527.3.1.1.8.2.31
The group of objects supporting management of obsoleted LDP FEC objects on Alcatel 7x50 SR series systems release 6.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor