ALC-OPT-MIB

File: ALC-OPT-MIB.mib (108108 bytes)

Imported modules

RFC1155-SMI RFC-1212

Imported symbols

Counter Gauge enterprises
OBJECT-TYPE

Defined Types

DisplayString  
OCTET STRING    

Cdx6500PPCTALCPortEntry  
SEQUENCE    
  alcPCfgPortNumber INTEGER
  alcPCfgPortType INTEGER
  alcPCfgSubtype INTEGER
  alcPCfgPortControl INTEGER
  alcPCfgClockSource INTEGER
  alcPCfgClockSpeed INTEGER
  alcPCfgPollDelayTimer INTEGER
  alcPCfgHostTimeout INTEGER
  alcPCfgMaxMesgSize INTEGER
  alcPCfgMinIntrvlBetweenPolls INTEGER
  alcPCfgRtsCtsTimeout INTEGER
  alcPCfgLeadPadChar OCTET STRING
  alcPCfgNumLeadPadChars INTEGER
  alcPCfgTrailPadChar OCTET STRING
  alcPCfgNumTrailPadChars INTEGER
  alcPCfgALCLineOptions DisplayString
  alcPCfgConnType INTEGER
  alcPCfgAcallMnemonic DisplayString
  alcPCfgCallingAddress DisplayString
  alcPCfgCUD DisplayString
  alcPCfgNumOfBuffers INTEGER
  alcPCfgInHeader DisplayString
  alcPCfgOutHeader DisplayString
  alcPCfgReconnectTimeout INTEGER
  alcPCfgInactivityTimeout INTEGER
  alcPCfgDebounceTimeout INTEGER
  alcPCfgParity INTEGER
  alcPCfgConnOptions DisplayString
  alcPCfgAvailableMesg DisplayString
  alcPCfgUnavailableMesg DisplayString

Cdx6500PPCTALCInterchangeEntry  
SEQUENCE    
  alcICfgPortNumber INTEGER
  alcICfgInterchangeAddress OCTET STRING
  alcICfgOptionOnInvalidCCC INTEGER
  alcICfgGenTerminalAddress OCTET STRING
  alcICfgHostTimeout INTEGER
  alcICfgMaxComponentsPerFrame INTEGER
  alcICfgFastPollCycleCount INTEGER
  alcICfgSlowPollCycleCount INTEGER
  alcICfgN1Counter INTEGER
  alcICfgN2Counter INTEGER
  alcICfgT1Timeout INTEGER
  alcICfgT2Timeout INTEGER
  alcICfgReenterMessage DisplayString
  alcICfgStartMessage DisplayString
  alcICfgStopMessage DisplayString
  alcICfgOptions DisplayString
  alcICfgValidTAList DisplayString
  alcICfgConnType INTEGER
  alcICfgAcallMnemonic DisplayString
  alcICfgCallingAddress DisplayString
  alcICfgCUD DisplayString
  alcICfgNumOfBuffers INTEGER
  alcICfgInHeader DisplayString
  alcICfgOutHeader DisplayString
  alcICfgReconnectTimeout INTEGER
  alcICfgInactivityTimeout INTEGER
  alcICfgDebounceTimeout INTEGER
  alcICfgParity INTEGER
  alcICfgConnOptions DisplayString
  alcICfgAvailableMesg DisplayString
  alcICfgUnavailableMesg DisplayString

Cdx6500PPCTALCTerminalEntry  
SEQUENCE    
  alcTCfgPortNumber INTEGER
  alcTCfgInterchangeAddress OCTET STRING
  alcTCfgTerminalAddress OCTET STRING
  alcTCfgConnType INTEGER
  alcTCfgAcallMnemonic DisplayString
  alcTCfgCallingAddress DisplayString
  alcTCfgCUD DisplayString
  alcTCfgNumOfBuffers INTEGER
  alcTCfgInHeader DisplayString
  alcTCfgOutHeader DisplayString
  alcTCfgReconnectTimeout INTEGER
  alcTCfgInactivityTimeout INTEGER
  alcTCfgDebounceTimeout INTEGER
  alcTCfgParity INTEGER
  alcTCfgConnOptions DisplayString
  alcTCfgAvailableMesg DisplayString
  alcTCfgUnavailableMesg DisplayString

Cdx6500PPSTALCPortEntry  
SEQUENCE    
  alcPStatsPortNumber INTEGER
  alcPStatsPortType INTEGER
  alcPStatsPortState INTEGER
  alcPStatsFramesIn Counter
  alcPStatsFramesOut Counter
  alcPStatsDataMesgsIn Counter
  alcPStatsDataMesgsOut Counter
  alcPStatsCharsIn Counter
  alcPStatsCharsOut Counter
  alcPStatsPolls Counter
  alcPStatsGAs Counter
  alcPStatsResets Counter
  alcPStatsDiscardBadIAIn Counter
  alcPStatsDiscardBadIAOut Counter
  alcPStatsMaxQSizeOut INTEGER
  alcPStatsCCCErrors Counter
  alcPStatsSignalLosses Counter
  alcPStatsOverlengthFrames Counter
  alcPStatsPortStatus INTEGER
  alcPStatsConnState INTEGER
  alcPStatsALCMesgsIn Counter
  alcPStatsALCMesgsOut Counter
  alcPStatsX25MesgsIn Counter
  alcPStatsX25MesgsOut Counter
  alcPStatsALCCharsIn Counter
  alcPStatsALCCharsOut Counter
  alcPStatsX25CharsIn Counter
  alcPStatsX25CharsOut Counter
  alcPStatsALCDiscardedMesgsEntityDown Counter
  alcPStatsX25DiscardedMesgsEntityDown Counter
  alcPStatsX25DiscardedMesgsBadALCAddr Counter
  alcPStatsX25DiscardedMesgsBadHeader Counter
  alcPStatsX25DiscardedMesgsTooLong Counter
  alcPStatsALCDiscardedMesgsQFull Counter
  alcPStatsX25DiscardedMesgsQFull Counter
  alcPStatsCurrTxALCQSize INTEGER
  alcPStatsCurrTxX25QSize INTEGER
  alcPStatsMaxTxALCQSize INTEGER
  alcPStatsMaxTxX25QSize INTEGER

Cdx6500PPSTALCInterchangeEntry  
SEQUENCE    
  alcIStatsPortNumber INTEGER
  alcIStatsInterchangeAddress OCTET STRING
  alcIStatsInterchangeState INTEGER
  alcIStatsFramesIn Counter
  alcIStatsFramesOut Counter
  alcIStatsDataMesgsIn Counter
  alcIStatsDataMesgsOut Counter
  alcIStatsCharsIn Counter
  alcIStatsCharsOut Counter
  alcIStatsPolls Counter
  alcIStatsGAs Counter
  alcIStatsResets Counter
  alcIStatsDiscardBadTAIn Counter
  alcIStatsDiscardBadTAOut Counter
  alcIStatsDisabledIAIn Counter
  alcIStatsDisabledIAOut Counter
  alcIStatsMaxQSizeOut INTEGER
  alcIStatsCCCErrors Counter
  alcIStatsT1Timeouts Counter
  alcIStatsT2Timeouts Counter
  alcIStatsConnState INTEGER
  alcIStatsALCMesgsIn Counter
  alcIStatsALCMesgsOut Counter
  alcIStatsX25MesgsIn Counter
  alcIStatsX25MesgsOut Counter
  alcIStatsALCCharsIn Counter
  alcIStatsALCCharsOut Counter
  alcIStatsX25CharsIn Counter
  alcIStatsX25CharsOut Counter
  alcIStatsALCDiscardedMesgsEntityDown Counter
  alcIStatsX25DiscardedMesgsEntityDown Counter
  alcIStatsX25DiscardedMesgsBadALCAddr Counter
  alcIStatsX25DiscardedMesgsBadHeader Counter
  alcIStatsX25DiscardedMesgsTooLong Counter
  alcIStatsALCDiscardedMesgsQFull Counter
  alcIStatsX25DiscardedMesgsQFull Counter
  alcIStatsCurrTxALCQSize INTEGER
  alcIStatsCurrTxX25QSize INTEGER
  alcIStatsMaxTxALCQSize INTEGER
  alcIStatsMaxTxX25QSize INTEGER

Cdx6500PPSTALCTerminalEntry  
SEQUENCE    
  alcTStatsPortNumber INTEGER
  alcTStatsInterchangeAddress OCTET STRING
  alcTStatsTerminalAddress OCTET STRING
  alcTStatsConnState INTEGER
  alcTStatsALCMesgsIn Counter
  alcTStatsALCMesgsOut Counter
  alcTStatsX25MesgsIn Counter
  alcTStatsX25MesgsOut Counter
  alcTStatsALCCharsIn Counter
  alcTStatsALCCharsOut Counter
  alcTStatsX25CharsIn Counter
  alcTStatsX25CharsOut Counter
  alcTStatsALCDiscardedMesgsEntityDown Counter
  alcTStatsX25DiscardedMesgsEntityDown Counter
  alcTStatsX25DiscardedMesgsBadALCAddr Counter
  alcTStatsX25DiscardedMesgsBadHeader Counter
  alcTStatsX25DiscardedMesgsTooLong Counter
  alcTStatsALCDiscardedMesgsQFull Counter
  alcTStatsX25DiscardedMesgsQFull Counter
  alcTStatsCurrTxALCQSize INTEGER
  alcTStatsCurrTxX25QSize INTEGER
  alcTStatsMaxTxALCQSize INTEGER
  alcTStatsMaxTxX25QSize INTEGER

Cdx6500ContALCPortEntry  
SEQUENCE    
  alcPContPortNumber INTEGER
  alcPContPortBoot INTEGER
  alcPContPortEnable INTEGER
  alcPContPortDisable INTEGER

Cdx6500ContALCInterchangeEntry  
SEQUENCE    
  alcIContPortNumber INTEGER
  alcIContInterchangeAddress OCTET STRING
  alcIContInterchangeBoot INTEGER
  alcIContInterchangeEnable INTEGER
  alcIContInterchangeDisable INTEGER

Cdx6500ContALCTerminalEntry  
SEQUENCE    
  alcTContPortNumber INTEGER
  alcTContInterchangeAddress OCTET STRING
  alcTContTerminalAddress OCTET STRING
  alcTContTerminalBoot INTEGER
  alcTContTerminalEnable INTEGER
  alcTContTerminalDisable INTEGER

Defined Values

codex 1.3.6.1.4.1.449
OBJECT IDENTIFIER    

cdxProductSpecific 1.3.6.1.4.1.449.2
OBJECT IDENTIFIER    

cdx6500 1.3.6.1.4.1.449.2.1
OBJECT IDENTIFIER    

cdx6500Configuration 1.3.6.1.4.1.449.2.1.2
OBJECT IDENTIFIER    

cdx6500CfgProtocolGroup 1.3.6.1.4.1.449.2.1.2.1
OBJECT IDENTIFIER    

cdx6500PCTPortProtocolGroup 1.3.6.1.4.1.449.2.1.2.1.1
OBJECT IDENTIFIER    

cdx6500Statistics 1.3.6.1.4.1.449.2.1.3
OBJECT IDENTIFIER    

cdx6500StatProtocolGroup 1.3.6.1.4.1.449.2.1.3.1
OBJECT IDENTIFIER    

cdx6500PSTPortProtocolGroup 1.3.6.1.4.1.449.2.1.3.1.1
OBJECT IDENTIFIER    

cdx6500Controls 1.3.6.1.4.1.449.2.1.4
OBJECT IDENTIFIER    

cdx6500PPCTALCCfgTable 1.3.6.1.4.1.449.2.1.2.1.1.27
OBJECT IDENTIFIER    

cdx6500PPCTALCPortTable 1.3.6.1.4.1.449.2.1.2.1.1.27.1
This table contains ALC Port configuration parameters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPCTALCPortEntry

cdx6500PPCTALCPortEntry 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1
Entries in the ALC Port Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PPCTALCPortEntry  

alcPCfgPortNumber 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.1
Port number of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..54  

alcPCfgPortType 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.2
Port Type of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER alc(31)  

alcPCfgSubtype 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.3
This is the ALC port subtype. alcHpad - Host PAD. alcTpad - Terminal PAD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER alcHpad(1), alcTpad(2)  

alcPCfgPortControl 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.4
Specify any of the following port control options: simp : Simple connection with no control signal handshake. dtr : Connection with DTR control signal handshake. emri : Port emulates a modem and does dial-in/out handshake with RI. emdc : Port emulates a modem and does dial-in/out handshake with DCD. alcDte : DTE emulation with RTS/CTS handshake.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER simp(1), emri(4), emdc(5), dtr(13), alcDte(15)  

alcPCfgClockSource 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.5
int : Internal clock source. ext : External clock source.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER int(1), ext(2)  

alcPCfgClockSpeed 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.6
This is the speed of the port in bits per second, when using internal clocking.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER clkspd1200(1), clkspd2400(2), clkspd4800(3), clkspd9600(4), clkspd19200(5), clkspd38400(6)  

alcPCfgPollDelayTimer 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.7
This is the delay in milliseconds to impose between poll cycles if no interchanges are polled. Valid on TPAD lines only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 50..100000  

alcPCfgHostTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.8
On a poll coerced line, the host is considered to be down if a poll is not received within this time, specified in milliseconds. Valid on HPAD lines only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 50..10000  

alcPCfgMaxMesgSize 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.9
This specifies the maximum size of messages that can be sent or received on this line excluding padding characters. TPAD may receive multiple messages in a frame, HPAD may transmit multiple messages in a frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 10..10000  

alcPCfgMinIntrvlBetweenPolls 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.10
The minimum length of time, in milliseconds, between polls issued on this line. Valid on TPAD lines only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100000  

alcPCfgRtsCtsTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.11
The time in milliseconds, within which CTS must be raised following the RTS signal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 50..10000  

alcPCfgLeadPadChar 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.12
This is the character to use when inserting leading padding characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

alcPCfgNumLeadPadChars 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.13
This is the number of leading padding characters to use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

alcPCfgTrailPadChar 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.14
This is the character to use when inserting trailing padding characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

alcPCfgNumTrailPadChars 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.15
This is the number of trailing padding characters to use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

alcPCfgALCLineOptions 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.16
Select options on this ALC port as follows: NONE : no option specified EMB_SYNC : Sychronization characters are inserted between messages in the same frame. MASK8 : Indicates that the `8' bit is treated as zero when examining interchange addresses on this line. COERCE : Poll coercion is used. CLASH : Poll responses will be aborted if a poll is received whilst a response to a previous poll is being transmitted. RFRTM : Responses will be generated to Response and Forward RTM messages. RZRTM : Responses will be generated to enquiry RTM messages. SOFT_SYNC : Selects software synchronization. NULLS : Nulls are allowed in the data stream. BACKTOBACK : Frames may be received back to back. Any combination of the above maybe specified by summing (e.g. NULLS+BACKTOBACK. . .).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(4..71)  

alcPCfgConnType 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.17
none : No connection. x25 : Connection type is X.25. nc : Skipped during configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), x25(2), nc(100)  

alcPCfgAcallMnemonic 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.18
This is the mnemonic to be used to establish the call when the call request is issued. The mnemonic must be defined in the mnemonic table. If no mnemonic is specified, ALP PAD will wait for the call. It consists of 0-8 alphanumeric characters, and the space character is used to blank the field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

alcPCfgCallingAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.19
The calling address to be used in outbound calls. It consists of 0-15 BCD digits, and the space character is used to blank the field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

alcPCfgCUD 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.20
The Call User Data field to be used in outbound calls. It consists of a list of up to 16 hexadecimal numbers between 0 and FF, separated by commas.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..47)  

alcPCfgNumOfBuffers 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.21
This defines the number of buffers that are available for data transfer in each direction. Each buffer will hold one message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

alcPCfgInHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.22
This data is assumed to be at the start of all messages received from X.25. If IA and/or TA are specified in the header, the values associated with these positions are checked against the IA and TA associated with the header is then removed from the message, and replaced by the IA and TA associated with the connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..53)  

alcPCfgOutHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.23
This data is prefixed to all messages sent to X.25. If IA and/or TA are specified in the header, the IA and TA associated with the connection are inserted into the outgoing message at the positions specified by the header. The IA and TA received from ALC are removed and replaced with the OUT Header.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..53)  

alcPCfgReconnectTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.24
The time in seconds between attempts to establish an X.25 virtual circuit when the ALP connection is enabled, or after the SVC has been cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

alcPCfgInactivityTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.25
The time in seconds after which the call is cleared if no data is transmitted or received. A value of 0 disables the timer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

alcPCfgDebounceTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.26
This defines the time in seconds for which the PAD waits before implementing the shutdown action. If the time out is 0, shutdown occurs immediately.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

alcPCfgParity 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.27
none : No parity will be used. odd : All messages sent to X.25 will have odd parity. nc : Skipped during configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), odd(2), nc(100)  

alcPCfgConnOptions 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.28
Options controlling the behaviour of the connection. NONE : No options are specified. HDR : ALP PAD discards all data messages incoming from the network in which the constant parts of the IN Header do not match the header of the message. ALCSD : If this option is specified and the SVC goes down, then the ALC entity is shutdown. CSD : If this option is specified and the ALC entity goes down, then the associated call is cleared. FLOW : If the number of free buffers decreases to 20% of its maximum, then flow control is imposed on the receiver. It is released when the number of free buffers reaches 50% of its maximum. If the option is not set, messages received when there are no buffers available will be discarded. Note that flow control requests from X.25 are always acted upon, regardless of the setting of this option. USE_ADDR : The address in the received message is used when the message is passed to ALC, and address checking is turned off. Any combination of the above maybe specified by summing (e.g. FLOW+USE_ADDR+. . .).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(3..32)  

alcPCfgAvailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.29
This specifies the text of a message that is broadcast to the ALC entity associated with this connection after a message from that terminal has been discarded due to the X.25 VC being down. This message is only sent if an Unavailable message has previously been sent to one of the terminals associated with this connection. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..62)  

alcPCfgUnavailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.1.1.30
This specifies the text of a message that is sent to a terminal when a message from that terminal is discarded because the X.25 VC is down. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..62)  

cdx6500PPCTALCInterchangeTable 1.3.6.1.4.1.449.2.1.2.1.1.27.2
This table contains ALC Interchange configuration parameters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPCTALCInterchangeEntry

cdx6500PPCTALCInterchangeEntry 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1
Entries in the ALC Interchange Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PPCTALCInterchangeEntry  

alcICfgPortNumber 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.1
Port number of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..54  

alcICfgInterchangeAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.2
The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

alcICfgOptionOnInvalidCCC 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.3
The action to be taken on receipt of a message with an invalid ccc. discard : Discard the message ignore : Treat the message as correct. reenter : (TPAD only) The configured `re-enter' message is sent to the terminal. resend : (TPAD only) A resend request message is sent to the terminal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER discard(2), resend(3), reenter(4), ignore(5)  

alcICfgGenTerminalAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.4
Specifies the terminal address to which broadcast messages are sent when the GTA option is specified.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

alcICfgHostTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.5
The host is considered to be down if a poll is not received within this period, which is specified in milliseconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 50..100000  

alcICfgMaxComponentsPerFrame 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.6
Specifies the maximum number of message segments transmitted in one frame (HPAD) or expected in one frame (TPAD).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..100  

alcICfgFastPollCycleCount 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.7
The polling rate for an interchange in fast poll. A poll is issued to this interchange once in every n poll cycles on the line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

alcICfgSlowPollCycleCount 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.8
The polling rate for an interchange in slow poll. One slow poll IA is polled every n poll cycles on the line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

alcICfgN1Counter 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.9
The number of polls that can be sent without receiving a response before the interchange enters slow poll.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..100  

alcICfgN2Counter 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.10
The number of good poll responses required before the interchange enters fast poll.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..100  

alcICfgT1Timeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.11
The time, in milliseconds, within which an interchange must start responding to a poll.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 100..100000  

alcICfgT2Timeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.12
The time, in milliseconds, within which an interchange must complete its transmission.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 100..100000  

alcICfgReenterMessage 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.13
This specifies the text of a message sent to terminals when a message with an incorrect ccc is received and the action on receipt of an invalid ccc is REENTER. Note that some terminals may require control characters at the start of the message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

alcICfgStartMessage 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.14
This specifies the text of a message sent to terminals when polling of this interchange is started and the STST option is configured. Note that some terminals may require control characters at the start of the message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

alcICfgStopMessage 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.15
This specifies the text of a message sent to terminals when polling of this interchange is stopped and the STST option is configured. Note that some terminals may require control characters at the start of the message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

alcICfgOptions 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.16
Select options on this ALC Interchange as follows : NONE : no option specified GTA : (TPAD only) Indicates that there is a general terminal address which may be used for broadcasting to all terminals on the interchange. NOPOLL : (TPAD only) Indicates that this interchange is not to be polled. RESET : Indicates that the interchange is capable of handling ALC Reset messages. STST : (TPAD only) Indicates that the configured start and stop messages should be transmitted when polling is started or stopped. Any combination of the above maybe specified by summing (e.g. GTA+NOPOLL+. . .).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(3..21)  

alcICfgValidTAList 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.17
A list of hexadecimal numbers between 1 and 3F separated by commas. /f or /r after each is used to indicate forward or reverse abort respectively. Ranges may be specified by separating two addresses by a dash `-'. Note that the addresses 0D, 1D, 2D, 3D and 3F are illegal. The list of terminal addresses that may be configured on the line, including the forward or reverse abort settings for each terminal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alcICfgConnType 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.18
none : No connection. x25 : Connection type is X.25. nc : Skipped during configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), x25(2), nc(100)  

alcICfgAcallMnemonic 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.19
This is the mnemonic to be used to establish the call when the call request is issued. The mnemonic must be defined in the mnemonic table. If no mnemonic is specified, ALP PAD will wait for the call. It consists of 0-8 alphanumeric characters, and the space character is used to blank the field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

alcICfgCallingAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.20
The calling address to be used in outbound calls. It consists of 0-15 BCD digits, and the space character is used to blank the field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

alcICfgCUD 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.21
The Call User Data field to be used in outbound calls. It consists of a list of up to 16 hexadecimal numbers between 0 and FF, separated by commas.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..47)  

alcICfgNumOfBuffers 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.22
This defined the number of buffers that are available for data transfer in each direction. Each buffer will hold one message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

alcICfgInHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.23
This data is assumed to be at the start of all messages received from X.25. If IA and/or TA are specified in the header, the values associated with these positions are checked against the IA and TA associated with the header is then removed from the message, and replaced by the IA and TA associated with the connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..53)  

alcICfgOutHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.24
This data is prefixed to all messages sent to X.25. If IA and/or TA are specified in the header, the IA and TA associated with the connection are inserted into the outgoing message at the positions specified by the header. The IA and TA received from ALC are removed and replaced with the OUT Header.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..53)  

alcICfgReconnectTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.25
The time in seconds between attempts to establish an X.25 virtual circuit when the ALP connection is enabled, or after the SVC has been cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

alcICfgInactivityTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.26
The time in seconds after which the call is cleared if no data is transmitted or received. A value of 0 disables the timer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

alcICfgDebounceTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.27
This defines the time in seconds for which the PAD waits before implementing the shutdown action. If the time out is 0, shutdown occurs immediately.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

alcICfgParity 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.28
none : No parity will be used. odd : All messages sent to X.25 will have odd parity. nc : Skipped during configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), odd(2), nc(100)  

alcICfgConnOptions 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.29
Options controlling the behaviour of the connection. NONE : No options are specified. HDR : ALP PAD discards all data messages incoming from the network in which the constant parts of the IN Header do not match the header of the message. ALCSD : If this option is specified and the SVC goes down, then the ALC entity is shutdown. CSD : If this option is specified and the ALC entity goes down, then the associated call is cleared. FLOW : If the number of free buffers decreases to 20% of its maximum, then flow control is imposed on the receiver. It is released when the number of free buffers reaches 50% of its maximum. If the option is not set, messages received when there are no buffers available will be discarded. Note that flow control requests from X.25 are always acted upon, regardless of the setting of this option. USE_ADDR : The address in the received message is used when the message is passed to ALC, and address checking is turned off. Any combination of the above maybe specified by summing (e.g. FLOW+USE_ADDR+. . .).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(3..32)  

alcICfgAvailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.30
This specifies the text of a message that is broadcast to the ALC entity associated with this connection after a message from that terminal has been discarded due to the X.25 VC being down. This message is only sent if an Unavailable message has previously been sent to one of the terminals associated with this connection. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..62)  

alcICfgUnavailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.2.1.31
This specifies the text of a message that is sent to a terminal when a message from that terminal is discarded because the X.25 VC is down. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..62)  

cdx6500PPCTALCTerminalTable 1.3.6.1.4.1.449.2.1.2.1.1.27.3
This table contains ALC Terminal configuration parameters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPCTALCTerminalEntry

cdx6500PPCTALCTerminalEntry 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1
Entries in the ALC Terminal Configuration Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PPCTALCTerminalEntry  

alcTCfgPortNumber 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.1
Port number of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..54  

alcTCfgInterchangeAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.2
The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

alcTCfgTerminalAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.3
Address identifying this terminal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

alcTCfgConnType 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.4
none : No connection type. x25 : Connection type is X.25. nc : Skipped during configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), x25(2), nc(100)  

alcTCfgAcallMnemonic 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.5
This is the mnemonic to be used to establish the call when the call request is issued. The mnemonic must be defined in the mnemonic table. If no mnemonic is specified, ALP PAD will wait for the call. It consists of 0-8 alphanumeric characters, and the space character is used to blank the field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

alcTCfgCallingAddress 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.6
The calling address to be used in outbound calls. It consists of 0-15 BCD digits, and the space character is used to blank the field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..15)  

alcTCfgCUD 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.7
The Call User Data field to be used in outbound calls. It consists of a list of up to 16 hexadecimal numbers between 0 and FF, separated by commas.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..47)  

alcTCfgNumOfBuffers 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.8
This defined the number of buffers that are available for data transfer in each direction. Each buffer will hold one message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

alcTCfgInHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.9
This data is assumed to be at the start of all messages received from X.25. If IA and/or TA are specified in the header, the values associated with these positions are checked against the IA and TA associated with the header is then removed from the message, and replaced by the IA and TA associated with the connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..53)  

alcTCfgOutHeader 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.10
This data is prefixed to all messages sent to X.25. If IA and/or TA are specified in the header, the IA and TA associated with the connection are inserted into the outgoing message at the positions specified by the header. The IA and TA received from ALC are removed and replaced with the OUT Header.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(2..53)  

alcTCfgReconnectTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.11
The time in seconds between attempts to establish an X.25 virtual circuit when the ALP connection is enabled, or after the SVC has been cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

alcTCfgInactivityTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.12
The time in seconds after which the call is cleared if no data is transmitted or received. A value of 0 disables the timer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

alcTCfgDebounceTimeout 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.13
This defines the time in seconds for which the PAD waits before implementing the shutdown action. If the time out is 0, shutdown occurs immediately.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

alcTCfgParity 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.14
none : No parity will be used. odd : All messages sent to X.25 will have odd parity. nc : Skipped during configuration
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), odd(2), nc(100)  

alcTCfgConnOptions 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.15
Options controlling the behaviour of the connection. NONE : No options are specified. HDR : ALP PAD discards all data messages incoming from the network in which the constant parts of the IN Header do not match the header of the message. ALCSD : If this option is specified and the SVC goes down, then the ALC entity is shutdown. CSD : If this option is specified and the ALC entity goes down, then the associated call is cleared. FLOW : If the number of free buffers decreases to 20% of its maximum, then flow control is imposed on the receiver. It is released when the number of free buffers reaches 50% of its maximum. If the option is not set, messages received when there are no buffers available will be discarded. Note that flow control requests from X.25 are always acted upon, regardless of the setting of this option. USE_ADDR : The address in the received message is used when the message is passed to ALC, and address checking is turned off. Any combination of the above maybe specified by summing (e.g. FLOW+USE_ADDR+. . .).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(3..32)  

alcTCfgAvailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.16
This specifies the text of a message that is broadcast to the ALC entity associated with this connection after a message from that terminal has been discarded due to the X.25 VC being down. This message is only sent if an Unavailable message has previously been sent to one of the terminals associated with this connection. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..62)  

alcTCfgUnavailableMesg 1.3.6.1.4.1.449.2.1.2.1.1.27.3.1.17
This specifies the text of a message that is sent to a terminal when a message from that terminal is discarded because the X.25 VC is down. If no message is defined, none is sent. The space character is used to blank this field. Note that this is only used on TPAD configurations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..62)  

cdx6500PPSTALCStatsTable 1.3.6.1.4.1.449.2.1.3.1.1.28
OBJECT IDENTIFIER    

cdx6500PPSTALCPortTable 1.3.6.1.4.1.449.2.1.3.1.1.28.1
This table contains ALC Port Statistics parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPSTALCPortEntry

cdx6500PPSTALCPortEntry 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1
Entries in the ALC Port Statistics Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PPSTALCPortEntry  

alcPStatsPortNumber 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.1
Port number of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..54  

alcPStatsPortType 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.2
Port type of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER alc(31)  

alcPStatsPortState 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.3
Current Port State. connecting:The line has been enabled by the operator, but polling has not yet been established. online :The line is active. offline :The line has been disabled by the operator. pending :The line is inactive because of conditions detected by ALP PAD (X.25 virtual circuit not active). timedOut :The line is not being polled. This will be displayed on poll coerced HPAD lines only. flowCtrl :The application (ALP PAD) has imposed flow control on the line. na :Value not Available
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(1), online(2), timedOut(7), pending(8), connecting(9), flowCtrl(11), na(100)  

alcPStatsFramesIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.4
Number of frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsFramesOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.5
Number of frames transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsDataMesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.6
Number of data messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsDataMesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.7
Number of data messages transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsCharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.8
Number of characters received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsCharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.9
Number of characters transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsPolls 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.10
Number of polls transmitted or received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsGAs 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.11
Number of Go Ahead messages transmitted or received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsResets 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.12
Number of Reset messages transmitted or received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsDiscardBadIAIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.13
Number of received messages discarded due to bad Interchange Address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsDiscardBadIAOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.14
Number of transmitted messages discarded due to bad Interchange Address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsMaxQSizeOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.15
Maximum transmit queue size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcPStatsCCCErrors 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.16
Number of messages received with an invalid checksum.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsSignalLosses 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.17
Number of Signal Losses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsOverlengthFrames 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.18
Number of overlength frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsPortStatus 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.19
Current Port Status. na :Value not Available
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), busyOut(3), up(4), down(5), na(100)  

alcPStatsConnState 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.20
Current state of the connection. online :The connection is available for data transfer. offline :The connection has been disabled by an operator. connecting:The ALP PAD is attempting to make the X.25 virtual circuit available for use. inactive :The inactivity timer has expired, so the virtual circuit has been dropped. Data received from ALC will cause the connection to be re-established. pending :The CSD option has been configured and the ALC entity is currently down; hence the ALP PAD has disabled the virtual circuit. na :Value not Available
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER online(1), offline(2), connecting(3), inactive(4), pending(5), na(100)  

alcPStatsALCMesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.21
The number of messages received from ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsALCMesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.22
The number of messages transmitted to ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsX25MesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.23
The number of messages received from X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsX25MesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.24
The number of messages transmitted to X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsALCCharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.25
The number of characters received from ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsALCCharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.26
The number of characters transmitted to ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsX25CharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.27
The number of characters received from X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsX25CharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.28
The number of characters transmitted to X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsALCDiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.29
The number of messages received by ALC for which the destination entity is unable to process the data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsX25DiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.30
The number of messages received by X.25 for which the destination entity is unable to process the data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsX25DiscardedMesgsBadALCAddr 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.31
The number of messages received from X.25 for which the addresses specified do not match those associated with the connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsX25DiscardedMesgsBadHeader 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.32
The number of messages received by X.25 of which the IN header configured does not match the header present in the message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsX25DiscardedMesgsTooLong 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.33
The number of messages received from X.25 that were discarded because they were longer than the allowable ALC maximum configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsALCDiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.34
The number of messages discarded because the ALC outbound message queue was full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsX25DiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.35
The number of messages discarded because the X.25 outbound message queue was full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcPStatsCurrTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.36
The number of messages currently queued in the ALC outbound message queue for transmission.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcPStatsCurrTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.37
The number of messages currently queued in the X.25 outbound message queue for transmission.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcPStatsMaxTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.38
The maximum (highwater mark) size of the ALC outbound queue so far.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcPStatsMaxTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.1.1.39
The maximum (highwater mark) size of the X.25 outbound queue so far.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PPSTALCInterchangeTable 1.3.6.1.4.1.449.2.1.3.1.1.28.2
This table contains ALC Interchange Statistics parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPSTALCInterchangeEntry

cdx6500PPSTALCInterchangeEntry 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1
Entries in the ALC Interchange Statistics Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PPSTALCInterchangeEntry  

alcIStatsPortNumber 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.1
Port number of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..54  

alcIStatsInterchangeAddress 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.2
The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

alcIStatsInterchangeState 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.3
Current State of this Interchange. online :The interchange is active. This is displayed for HPAD interchanges, and TPAD interchanges configured as NOPOLL, only. offline :The interchange has been disabled by the operator. pending :The interchange is inactive because of conditions detected by the application (ALP PAD). failed :The line with which this interchange is associated is down. timedOut:The interchange is not being polled. This is displayed for HPAD interchanges on non poll-coerced lines only. flowCtrl:The application (ALP PAD) has imposed flow control on the interchange. stopped :The line with which this interchange is associated is in the FLOW CONTROL state. This is valid for TPAD interchanges only. slowPoll:The interchange is in slow poll. fastPoll:The interchange is in fast poll. na :Value not Available
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(1), online(2), fastPoll(3), slowPoll(4), stopped(6), timedOut(7), pending(8), failed(10), flowCtrl(11), na(100)  

alcIStatsFramesIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.4
Number of ALC frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsFramesOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.5
Number of ALC frames transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsDataMesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.6
Number of ALC data messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsDataMesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.7
Number of ALC data messages transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsCharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.8
Total number of characters received, excluding synchronization characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsCharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.9
Total number of characters transmitted, excluding synchronization characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsPolls 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.10
The number of poll messages transmitted for a line defined as a TPAD. The number received for one defined as HPAD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsGAs 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.11
The number of Go Ahead messages transmitted for a line defined as HPAD. The number received for one defined as TPAD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsResets 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.12
The number of Reset messages transmitted for a line defined as TPAD. The number received for one defined as HPAD.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsDiscardBadTAIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.13
The number of received messages discarded because the Terminal Address was not defined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsDiscardBadTAOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.14
The number of transmitted messages discarded because the Terminal Address was not defined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsDisabledIAIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.15
The number of received messages discarded because the Interchange was disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsDisabledIAOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.16
The number of transmitted messages discarded because the Interchange was disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsMaxQSizeOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.17
Maximum number of frames queued for transmission.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcIStatsCCCErrors 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.18
Number of messages received with an invalid checksum.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsT1Timeouts 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.19
Number of T1 timer expirations. This is defined for TPAD only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsT2Timeouts 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.20
Number of T2 timer expirations. This is defined for TPAD only.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsConnState 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.21
Current state of the connection. online :The connection is available for data transfer. offline :The connection has been disabled by an operator. connecting:The ALP PAD is attempting to make the X.25 virtual circuit available for use. inactive :The inactivity timer has expired, so the virtual circuit has been dropped. Data received from ALC will cause the connection to be re-established. pending :The CSD option has been configured and the ALC entity is currently down; hence the ALP PAD has disabled the virtual circuit. na :Value not Available
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER online(1), offline(2), connecting(3), inactive(4), pending(5), na(100)  

alcIStatsALCMesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.22
The number of messages received from ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsALCMesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.23
The number of messages transmitted to ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsX25MesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.24
The number of messages received from X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsX25MesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.25
The number of messages transmitted to X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsALCCharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.26
The number of characters received from ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsALCCharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.27
The number of characters transmitted to ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsX25CharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.28
The number of characters received from X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsX25CharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.29
The number of characters transmitted to X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsALCDiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.30
The number of messages received by ALC for which the destination entity is unable to process the data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsX25DiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.31
The number of messages received by X.25 for which the destination entity is unable to process the data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsX25DiscardedMesgsBadALCAddr 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.32
The number of messages received from X.25 for which the addresses specified do not match those associated with the connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsX25DiscardedMesgsBadHeader 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.33
The number of messages received by X.25 of which the IN header configured does not match the header present in the message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsX25DiscardedMesgsTooLong 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.34
The number of messages received from X.25 that were discarded because they were longer than the allowable ALC maximum configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsALCDiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.35
The number of messages discarded because the ALC outbound message queue was full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsX25DiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.36
The number of messages discarded because the X.25 outbound message queue was full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcIStatsCurrTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.37
The number of messages currently queued in the ALC outbound message queue for transmission.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcIStatsCurrTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.38
The number of messages currently queued in the X.25 outbound message queue for transmission.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcIStatsMaxTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.39
The maximum (highwater mark) size of the ALC outbound queue so far.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcIStatsMaxTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.2.1.40
The maximum (highwater mark) size of the X.25 outbound queue so far.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500PPSTALCTerminalTable 1.3.6.1.4.1.449.2.1.3.1.1.28.3
This table contains ALC Terminalinal Statistics parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500PPSTALCTerminalEntry

cdx6500PPSTALCTerminalEntry 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1
Entries in the ALC Terminalinal Statistics Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500PPSTALCTerminalEntry  

alcTStatsPortNumber 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.1
Port number of this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..54  

alcTStatsInterchangeAddress 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.2
The address of the interchange. Addresses 0D,0F,1D,2D,3D and 3F are illegal as they are used as line control characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

alcTStatsTerminalAddress 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.3
Address identifying this terminal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

alcTStatsConnState 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.4
Current state of the connection. online :The connection is available for data transfer. offline :The connection has been disabled by an operator. connecting:The ALP PAD is attempting to make the X.25 virtual circuit available for use. inactive :The inactivity timer has expired, so the virtual circuit has been dropped. Data received from ALC will cause the connection to be re-established. pending :The CSD option has been configured and the ALC entity is currently down; hence the ALP PAD has disabled the virtual circuit. na :Value not Available
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER online(1), offline(2), connecting(3), inactive(4), pending(5), na(100)  

alcTStatsALCMesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.5
The number of messages received from ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsALCMesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.6
The number of messages transmitted to ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsX25MesgsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.7
The number of messages received from X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsX25MesgsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.8
The number of messages transmitted to X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsALCCharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.9
The number of characters received from ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsALCCharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.10
The number of characters transmitted to ALC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsX25CharsIn 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.11
The number of characters received from X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsX25CharsOut 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.12
The number of characters transmitted to X.25.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsALCDiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.13
The number of messages received by ALC for which the destination entity is unable to process the data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsX25DiscardedMesgsEntityDown 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.14
The number of messages received by X.25 for which the destination entity is unable to process the data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsX25DiscardedMesgsBadALCAddr 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.15
The number of messages received from X.25 for which the addresses specified do not match those associated with the connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsX25DiscardedMesgsBadHeader 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.16
The number of messages received by X.25 of which the IN header configured does not match the header present in the message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsX25DiscardedMesgsTooLong 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.17
The number of messages received from X.25 that were discarded because they were longer than the allowable ALC maximum configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsALCDiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.18
The number of messages discarded because the ALC outbound message queue was full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsX25DiscardedMesgsQFull 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.19
The number of messages discarded because the X.25 outbound message queue was full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alcTStatsCurrTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.20
The number of messages currently queued in the ALC outbound message queue for transmission.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcTStatsCurrTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.21
The number of messages currently queued in the X.25 outbound message queue for transmission.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcTStatsMaxTxALCQSize 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.22
The maximum (highwater mark) size of the ALC outbound queue so far.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alcTStatsMaxTxX25QSize 1.3.6.1.4.1.449.2.1.3.1.1.28.3.1.23
The maximum (highwater mark) size of the X.25 outbound queue so far.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cdx6500ContALC 1.3.6.1.4.1.449.2.1.4.10
OBJECT IDENTIFIER    

cdx6500ContALCPortTable 1.3.6.1.4.1.449.2.1.4.10.1
This table contains ALC Port Control parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500ContALCPortEntry

cdx6500ContALCPortEntry 1.3.6.1.4.1.449.2.1.4.10.1.1
Entries in the ALC Port Control Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500ContALCPortEntry  

alcPContPortNumber 1.3.6.1.4.1.449.2.1.4.10.1.1.1
ALC Port Number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..54  

alcPContPortBoot 1.3.6.1.4.1.449.2.1.4.10.1.1.2
Boots the specified ALC Port. boot - Boot the port. noBoot - Do not boot the port.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER boot(1), noBoot(2)  

alcPContPortEnable 1.3.6.1.4.1.449.2.1.4.10.1.1.3
Enables the specified ALC Port. enable - Enable the port. noEnable - Do not enable the port.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER enable(1), noEnable(2)  

alcPContPortDisable 1.3.6.1.4.1.449.2.1.4.10.1.1.4
Disables the specified ALC Port. disable - Disable the port. noDisable - Do not disable the port.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER disable(1), noDisable(2)  

cdx6500ContALCInterchangeTable 1.3.6.1.4.1.449.2.1.4.10.2
This table contains ALC Interchange Control parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500ContALCInterchangeEntry

cdx6500ContALCInterchangeEntry 1.3.6.1.4.1.449.2.1.4.10.2.1
Entries in the ALC Interchange Control Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500ContALCInterchangeEntry  

alcIContPortNumber 1.3.6.1.4.1.449.2.1.4.10.2.1.1
ALC Port Number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..54  

alcIContInterchangeAddress 1.3.6.1.4.1.449.2.1.4.10.2.1.2
ALC Interchange address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(1)  

alcIContInterchangeBoot 1.3.6.1.4.1.449.2.1.4.10.2.1.3
Boots the specified ALC Interchange. boot - Boot the interchange. noBoot - Do not boot the interchange.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER boot(1), noBoot(2)  

alcIContInterchangeEnable 1.3.6.1.4.1.449.2.1.4.10.2.1.4
Enables the specified ALC Interchange. enable - Enable the interchange. noEnable - Do not enable the interchange.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER enable(1), noEnable(2)  

alcIContInterchangeDisable 1.3.6.1.4.1.449.2.1.4.10.2.1.5
Disables the specified ALC Interchange. disable - Disable the interchange. noDisable - Do not disable the interchange.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER disable(1), noDisable(2)  

cdx6500ContALCTerminalTable 1.3.6.1.4.1.449.2.1.4.10.3
This table contains ALC Terminal Control parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Cdx6500ContALCTerminalEntry

cdx6500ContALCTerminalEntry 1.3.6.1.4.1.449.2.1.4.10.3.1
Entries in the ALC Terminal Control Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Cdx6500ContALCTerminalEntry  

alcTContPortNumber 1.3.6.1.4.1.449.2.1.4.10.3.1.1
ALC Port Number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..54  

alcTContInterchangeAddress 1.3.6.1.4.1.449.2.1.4.10.3.1.2
ALC Interchange address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(1)  

alcTContTerminalAddress 1.3.6.1.4.1.449.2.1.4.10.3.1.3
Address identifying this terminal.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(1)  

alcTContTerminalBoot 1.3.6.1.4.1.449.2.1.4.10.3.1.4
Boots the specified ALC terminal. boot - Boot the terminal. noBoot - Do not boot the terminal.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER boot(1), noBoot(2)  

alcTContTerminalEnable 1.3.6.1.4.1.449.2.1.4.10.3.1.5
Enables the specified ALC Terminal. enable - Enable the terminal. noEnable - Do not enable the terminal.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER enable(1), noEnable(2)  

alcTContTerminalDisable 1.3.6.1.4.1.449.2.1.4.10.3.1.6
Disables the specified ALC terminal. disable - Disable the terminal. noDisable - Do not disable the terminal.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER disable(1), noDisable(2)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor