ADTRAN-DS1-MIB

File: ADTRAN-DS1-MIB.mib (24763 bytes)

Imported modules

RFC1155-SMI RFC-1212

Imported symbols

enterprises OBJECT-TYPE

Defined Types

AdDS1AlarmEntry  
SEQUENCE    
  adDS1AlarmIndex INTEGER
  adDS1AlarmEnable INTEGER
  adDS1LineEvent INTEGER
  adDS1LineArm INTEGER

AdDS1AlertEntry  
SEQUENCE    
  adDS1AlertIndex INTEGER
  adDS1AlertEnable INTEGER
  adDS1CurrentAlert INTEGER
  adDS1TotalAlert INTEGER
  adDS1FarCurrentAlert INTEGER
  adDS1FarTotalAlert INTEGER
  adDS1CurrentArm INTEGER
  adDS1TotalArm INTEGER
  adDS1FarCurrentArm INTEGER
  adDS1FarTotalArm INTEGER

Defined Values

adtran 1.3.6.1.4.1.664
OBJECT IDENTIFIER    

adMgmt 1.3.6.1.4.1.664.2
OBJECT IDENTIFIER    

adDS1mg 1.3.6.1.4.1.664.2.3
OBJECT IDENTIFIER    

adDS1AlarmTable 1.3.6.1.4.1.664.2.3.1
The DS1 Alarm Event Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdDS1AlarmEntry

adDS1AlarmEntry 1.3.6.1.4.1.664.2.3.1.1
An entry in the DS1 Alarm Event Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdDS1AlarmEntry  

adDS1AlarmIndex 1.3.6.1.4.1.664.2.3.1.1.1
The index value which uniquely identifies the DS1 interface. The interface identified by a particular value of this index is the same interface as identified by dsx1LineIndex in DS1 MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

adDS1AlarmEnable 1.3.6.1.4.1.664.2.3.1.1.2
Enables or disables the generation of DS1 Alarm Traps for Line Status event changes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ds1AlarmOFF(1), ds1AlarmON(2)  

adDS1LineEvent 1.3.6.1.4.1.664.2.3.1.1.3
This bit map variable indicates state changes in the DS1 line status variable (dsx1LineStatus). When a line status bit changes state, the corresponding line event bit is set in this variable. If armed, setting the event will generate an Alarm Trap. After reporting the events in an Alarm Trap or Get response, the device clears the reported events. The various alarm event bit positions are: 1 No Alarm Present 2 Far end LOF ( a.k.a., Yellow Alarm ) 4 Near end sending LOF Indication 8 Far end sending AIS ( Blue Alarm ) 16 Near end sending AIS 32 Near end LOF ( a.k.a., Red Alarm ) 64 Near end Loss Of Signal 128 Near end is looped 256 E1 TS16 AIS 512 Far End Sending TS16 LOMF 1024 Near End Sending TS16 LOMF 2048 Near End detects a test code 4096 any line status not defined here
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4095  

adDS1LineArm 1.3.6.1.4.1.664.2.3.1.1.4
This bit map variable arms or disarms an individual or group of events identified in adDS1LineEvent as a source for generation of DS1 Alarm Trap. The various arm event bit positions are: 1 No Alarm Present 2 Far end LOF ( a.k.a., Yellow Alarm ) 4 Near end sending LOF Indication 8 Far end sending AIS ( Blue Alarm ) 16 Near end sending AIS 32 Near end LOF ( a.k.a., Red Alarm ) 64 Near end Loss Of Signal 128 Near end is looped 256 E1 TS16 AIS 512 Far End Sending TS16 LOMF 1024 Near End Sending TS16 LOMF 2048 Near End detects a test code 4096 any line status not defined here
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4095  

adDS1AlertTable 1.3.6.1.4.1.664.2.3.2
The DS1 Alert Event Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdDS1AlertEntry

adDS1AlertEntry 1.3.6.1.4.1.664.2.3.2.1
An entry in the DS1 Alert Event Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdDS1AlertEntry  

adDS1AlertIndex 1.3.6.1.4.1.664.2.3.2.1.1
The index value which uniquely identifies the DS1 interface. The interface identified by a particular value of this index is the same interface as identified by dsx1LineIndex in DS1 MIB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

adDS1AlertEnable 1.3.6.1.4.1.664.2.3.2.1.2
Enables or disables the generation of DS1 Alert Traps for Performance Monitor Threshold Crossing Alerts.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ds1AlertOFF(1), ds1AlertON(2)  

adDS1CurrentAlert 1.3.6.1.4.1.664.2.3.2.1.3
This DS1 performance status variable indicates Threshold Crossing Alerts for Near End Current 15 minute interval. An alert bit is set in this variable when the value of the dsx1CurrentTable object exceeds the Threshold Value. This variable contains the sum of alert values. Threshold Crossing Alert bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes 512 LCV - Line Code Violations
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1023  

adDS1TotalAlert 1.3.6.1.4.1.664.2.3.2.1.4
This DS1 performance status variable indicates Threshold Crossing Alerts for Near End Total performance variables. An alert bit is set in this variable when the value of the dsx1TotalTable object exceeds the Threshold Value. This variable contains the sum of alert values. Threshold Crossing Alert bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes 512 LCV - Line Code Violations
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1023  

adDS1FarCurrentAlert 1.3.6.1.4.1.664.2.3.2.1.5
This DS1 performance status variable indicates Threshold Crossing Alerts for Far End Current 15 minute interval. An alert bit is set in this variable when the value of the dsx1FarEndCurrentTable object exceeds the Threshold Value. This variable contains the sum of alert values. Threshold Crossing Alert bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..511  

adDS1FarTotalAlert 1.3.6.1.4.1.664.2.3.2.1.6
This DS1 performance status variable indicates Threshold Crossing Alerts for Far End Total performance variables. An alert bit is set in this variable when the value of the dsx1FarEndTotalTable object exceeds the Threshold Value. This variable contains the sum of alert values. Threshold Crossing Alert bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..511  

adDS1CurrentArm 1.3.6.1.4.1.664.2.3.2.1.7
This variable arms and disarms an individual or group of alerts identified in adDS1CurrentAlert as a source for the generation of Threshold Crossing Alert Trap. This variable contains the sum of Arm values. Threshold Crossing Arm bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 512 LCV - Line Code Violations
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..1023  

adDS1TotalArm 1.3.6.1.4.1.664.2.3.2.1.8
This variable arms and disarms an individual or group of alerts identified in adDS1TotalAlert as a source for the generation of Threshold Crossing Alert Trap. This variable contains the sum of Arm values. Threshold Crossing Arm bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 512 LCV - Line Code Violations
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..1023  

adDS1FarCurrentArm 1.3.6.1.4.1.664.2.3.2.1.9
This variable arms and disarms an individual or group of alerts identified in adDS1FarCurrentAlert as a source for the generation of Threshold Crossing Alert Trap. This variable contains the sum of Arm values. Threshold Crossing Arm bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..511  

adDS1FarTotalArm 1.3.6.1.4.1.664.2.3.2.1.10
This variable arms and disarms an individual or group of alerts identified in adDS1FarTotalAlert as a source for the generation of Threshold Crossing Alert Trap. This variable contains the sum of Arm values. Threshold Crossing Arm bit position values: 1 ES - Errored Seconds 2 SES - Severely Errored Seconds 4 SEFS - Severely Errored Framing Seconds 8 UAS - Unavailable Seconds 16 CSS - Controlled Slip Seconds 32 PCV - Path Coding Violations 64 LES - Line Errored Seconds 128 BES - Bursty Errored Seconds 256 DM - Degraded Minutes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..511  

adDS1CurrentThreshold 1.3.6.1.4.1.664.2.3.3
OBJECT IDENTIFIER    

adDS1CurrentThrsES 1.3.6.1.4.1.664.2.3.3.1
The DS1 performance monitor Threshold Value for the Current 15 minute Errored Seconds parameter. The default value is 65 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1CurrentThrsSES 1.3.6.1.4.1.664.2.3.3.2
The DS1 performance monitor Threshold Value for the Current 15 minute Severely Errored Seconds parameter. The default value is 10 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1CurrentThrsSEFS 1.3.6.1.4.1.664.2.3.3.3
The DS1 performance monitor Threshold Value for the Current 15 minute Severely Errored Framing Seconds parameter. The default value is 2 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1CurrentThrsUAS 1.3.6.1.4.1.664.2.3.3.4
The DS1 performance monitor Threshold Value for the Current 15 minute Unavailable Seconds parameter. The default value is 10 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1CurrentThrsCSS 1.3.6.1.4.1.664.2.3.3.5
The DS1 performance monitor Threshold Value for the Current 15 minute Controlled Slip Seconds parameter. The default value is 1 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1CurrentThrsPCVsf 1.3.6.1.4.1.664.2.3.3.6
The DS1 performance monitor Threshold Value for the Current 15 minute Path Coding Violations parameter, when the Line Type is Super Frame (AT&T D4 format) DS1. Default value for an approximate BER level of (10**-5) is 72 Framing errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1CurrentThrsPCVesf 1.3.6.1.4.1.664.2.3.3.7
The DS1 performance monitor Threshold Value for the Current 15 minute Path Coding Violations parameter, when the Line Type is Extended Super Frame (ESF) DS1. Default value for an approximate BER level of (10**-5) is 13,296 CRC errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1CurrentThrsLES 1.3.6.1.4.1.664.2.3.3.8
The DS1 performance monitor Threshold Value for the Current 15 minute Line Errored Seconds parameter. The default value is 65 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1CurrentThrsLCV 1.3.6.1.4.1.664.2.3.3.9
The DS1 performance monitor Threshold Value for the Current 15 minute Line Code Violations parameter. The default value is 13,340 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1TotalThreshold 1.3.6.1.4.1.664.2.3.4
OBJECT IDENTIFIER    

adDS1TotalThrsES 1.3.6.1.4.1.664.2.3.4.1
The DS1 performance monitor Threshold Value for the Total Errored Seconds parameter. The default value is 648 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1TotalThrsSES 1.3.6.1.4.1.664.2.3.4.2
The DS1 performance monitor Threshold Value for the Total Severely Errored Seconds parameter. The default value is 100 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1TotalThrsSEFS 1.3.6.1.4.1.664.2.3.4.3
The DS1 performance monitor Threshold Value for the Total Severely Errored Framing Seconds parameter. The default value is 17 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1TotalThrsUAS 1.3.6.1.4.1.664.2.3.4.4
The DS1 performance monitor Threshold Value for the Total Unavailable Seconds parameter. The default value is 10 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1TotalThrsCSS 1.3.6.1.4.1.664.2.3.4.5
The DS1 performance monitor Threshold Value for the Total Controlled Slip Seconds parameter. The default value is 4 for an approximate BER level of(10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1TotalThrsPCVsf 1.3.6.1.4.1.664.2.3.4.6
The DS1 performance monitor Threshold Value for the Total Path Coding Violations parameter, when the Line Type is Super Frame (AT&T D4 format) DS1. The default value for an approximate BER level of (10**-5) is 691 framing errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1TotalThrsPCVesf 1.3.6.1.4.1.664.2.3.4.7
The DS1 performance monitor Threshold Value for the Total Path Coding Violations parameter, when the Line Type is Extended Super Frame (ESF) DS1. The default value for an approximate BER level of (10**-5) is 132,960 CRC errors.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1TotalThrsLES 1.3.6.1.4.1.664.2.3.4.8
The DS1 performance monitor Threshold Value for the Total Line Errored Seconds parameter. The default value is 648 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adDS1TotalThrsLCV 1.3.6.1.4.1.664.2.3.4.9
The DS1 performance monitor Threshold Value for the Total Line Code Violations parameter. The default value is 133,400 for an approximate BER level of (10** -5).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER