ADSL-DMT-LINE-MIB

File: ADSL-DMT-LINE-MIB.mib (24734 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF IF-MIB
ADSL-LINE-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE MODULE-COMPLIANCE
OBJECT-GROUP ifIndex adslLCSMib
adslLineConfProfileName

Defined Types

AdslLineDmtEntry  
SEQUENCE    
  adslLineDmtTrellis INTEGER
  adslLineDmtEOC INTEGER

AdslAtucDmtPhysEntry  
SEQUENCE    
  adslAtucDmtIssue INTEGER
  adslAtucDmtState INTEGER
  adslAtucDmtInterleavePath INTEGER
  adslAtucDmtFastPath INTEGER

AdslAturDmtPhysEntry  
SEQUENCE    
  adslAturDmtIssue INTEGER
  adslAturDmtState INTEGER
  adslAturDmtInterleavePath INTEGER
  adslAturDmtFastPath INTEGER

AdslLineDmtConfProfileEntry  
SEQUENCE    
  adslAtucDmtConfFreqBins OCTET STRING
  adslAturDmtConfFreqBins OCTET STRING
  adslLineDmtConfMode INTEGER
  adslLineDmtConfTrellis INTEGER
  adslLineDmtConfEOC INTEGER
  adslAtucDmtConfInterleavePath INTEGER
  adslAtucDmtConfFastPath INTEGER
  adslAturDmtConfInterleavePath INTEGER
  adslAturDmtConfFastPath INTEGER

Defined Values

adslLineDmtMIB 1.3.6.1.2.1.10.94.1.1.16.2
Naming Conventions: Atuc -- (ATUC) modem at near (Central) end of line Atur -- (ATUR) modem at Remote end of line ES -- Errored Second. LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power
MODULE-IDENTITY    

adslLineDmtMIBObjects 1.3.6.1.2.1.10.94.1.1.16.2.1
OBJECT IDENTIFIER    

adslLineDmtTable 1.3.6.1.2.1.10.94.1.1.16.2.1.1
This table extends the adslLineTable and contains common attributes describing both ends of ADSL lines supported by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLineDmtEntry

adslLineDmtEntry 1.3.6.1.2.1.10.94.1.1.16.2.1.1.1
A set of common attributes describing both ends of an ADSL line supported by the system. There exist an entry for each ifEntry with an ifType of adsl(94).
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslLineDmtEntry  

adslLineDmtTrellis 1.3.6.1.2.1.10.94.1.1.16.2.1.1.1.1
Reports whether the Trellis coding is used on the DMT line. Use of trellis coding is determined at line initialization with C-MSGS1 and R-MSGS1 exchanges and will not change until the line is re-initialized.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER trellisOn(1), trellisOff(2)  

adslLineDmtEOC 1.3.6.1.2.1.10.94.1.1.16.2.1.1.1.2
Reports whether the eoc can support autonomous data streaming mode or only transaction mode. After initialization, unknown is reported until sufficient autonomous eoc messages have been transmitted to determine the true capability of both ATUs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), transaction(2), streaming(3)  

adslAtucDmtPhysTable 1.3.6.1.2.1.10.94.1.1.16.2.1.2
This table extends the adslAtucPhysTable and contains specific physical layer parameters for the ATU-C class devices supported by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAtucDmtPhysEntry

adslAtucDmtPhysEntry 1.3.6.1.2.1.10.94.1.1.16.2.1.2.1
A set of physical-layer parameters for an ATU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of adsl(94).
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslAtucDmtPhysEntry  

adslAtucDmtIssue 1.3.6.1.2.1.10.94.1.1.16.2.1.2.1.1
Reports the issue number of the relevant standard that the DMT ADSL transceiver at the ATU-C is currently operating to. The issue number will be fixed by the hardware and is transmitted by the ATU-C in C-MSGS1 during initialization.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), t1413Issue1(2), t1413Issue2(3), t1413Issue3(4), gdmtIssue1(5), etsiIssue1(6)  

adslAtucDmtState 1.3.6.1.2.1.10.94.1.1.16.2.1.2.1.2
Reports current state of the ATU-C DMT transceiver. The current state can change dynamically. The SNMP agent reports the state after querying the ATU-C state machine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), powerUp(2), configure(3), idle(4), quiet(5), tone(6), activating(7), training(8), analyzing(9), exchange(10), steadyState(11), notResponding(12)  

adslAtucDmtInterleavePath 1.3.6.1.2.1.10.94.1.1.16.2.1.2.1.3
Reports bearer channel of downstream interleaved path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), as0(2), as1(3)  

adslAtucDmtFastPath 1.3.6.1.2.1.10.94.1.1.16.2.1.2.1.4
Reports bearer channel of downstream fast path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), as0(2), as1(3)  

adslAturDmtPhysTable 1.3.6.1.2.1.10.94.1.1.16.2.1.3
This table extends the adslAturPhysTable and contains physical layer parameters for the ATU-R class devices supported by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslAturDmtPhysEntry

adslAturDmtPhysEntry 1.3.6.1.2.1.10.94.1.1.16.2.1.3.1
A set of physical-layer parameters for an ATU-R class device supported by the system. There exists an entry for each ifEntry with an ifType of adsl(94).
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslAturDmtPhysEntry  

adslAturDmtIssue 1.3.6.1.2.1.10.94.1.1.16.2.1.3.1.1
Reports the issue number of the relevant standard that the DMT ADSL transceiver at the ATU-R is currently operating to. The issue number will be fixed by the hardware and is transmitted by the ATU-R in R-MSGS1 during initialization.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), t1413Issue1(2), t1413Issue2(3), t1413Issue3(4), gdmtIssue1(5), etsiIssue1(6)  

adslAturDmtState 1.3.6.1.2.1.10.94.1.1.16.2.1.3.1.2
Reports current state of the ATU-R DMT transceiver. The current state can change dynamically. ATU-R state is reported by the SNMP agent at the ATU-C which infers the state depending on the ATU-C state. When the inference cannot be made, unknown state is returned.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), activating(2), training(3), analyzing(4), exchange(5), steadyState(6)  

adslAturDmtInterleavePath 1.3.6.1.2.1.10.94.1.1.16.2.1.3.1.3
Reports bearer channel of upstream interleaved path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), ls0(2), ls1(3)  

adslAturDmtFastPath 1.3.6.1.2.1.10.94.1.1.16.2.1.3.1.4
Reports bearer channel of upstream fast path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), ls0(2), ls1(3)  

adslAtucDmtChanTable 1.3.6.1.2.1.10.94.1.1.16.2.1.4
OBJECT IDENTIFIER    

adslAturDmtChanTable 1.3.6.1.2.1.10.94.1.1.16.2.1.5
OBJECT IDENTIFIER    

adslAtucDmtPerfDataTable 1.3.6.1.2.1.10.94.1.1.16.2.1.6
OBJECT IDENTIFIER    

adslAturDmtPerfDataTable 1.3.6.1.2.1.10.94.1.1.16.2.1.7
OBJECT IDENTIFIER    

adslAtucDmtIntervalTable 1.3.6.1.2.1.10.94.1.1.16.2.1.8
OBJECT IDENTIFIER    

adslAturDmtIntervalTable 1.3.6.1.2.1.10.94.1.1.16.2.1.9
OBJECT IDENTIFIER    

adslAtucDmtChanPerfDataTable 1.3.6.1.2.1.10.94.1.1.16.2.1.10
OBJECT IDENTIFIER    

adslAturDmtChanPerfDataTable 1.3.6.1.2.1.10.94.1.1.16.2.1.11
OBJECT IDENTIFIER    

adslAtucDmtChanIntervalTable 1.3.6.1.2.1.10.94.1.1.16.2.1.12
OBJECT IDENTIFIER    

adslAturDmtChanIntervalTable 1.3.6.1.2.1.10.94.1.1.16.2.1.13
OBJECT IDENTIFIER    

adslLineDmtConfProfileIndexNext 1.3.6.1.2.1.10.94.1.1.16.2.1.14
OBJECT IDENTIFIER    

adslLineDmtConfProfileTable 1.3.6.1.2.1.10.94.1.1.16.2.1.15
This table extends the adslLineConfProfileTable and contains ADSL DMT line configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLineDmtConfProfileEntry

adslLineDmtConfProfileEntry 1.3.6.1.2.1.10.94.1.1.16.2.1.15.1
A configuration profile containing ADSL DMT line configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslLineDmtConfProfileEntry  

adslAtucDmtConfFreqBins 1.3.6.1.2.1.10.94.1.1.16.2.1.15.1.1
A string of 32 bits to enable/disable the incoming DMT frequency bins that the ATU-C receiver monitors. Each bit controls one bin with the first bit of the first octet controlling sub-carrier zero (lowest frequency bin). A bit set to 1 disables reception of the specified sub- carrier frequency bin end a 0 enables reception.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(4)  

adslAturDmtConfFreqBins 1.3.6.1.2.1.10.94.1.1.16.2.1.15.1.2
A string of 256 bits to enable/disable the incoming DMT frequency bins that the ATU-R receiver should monitor after the next activation. The mechanism to pass adslAturDMTConfFreqBins to the ATU-R is vendor specific. Each bit controls one bin with the first bit of the first octet controlling sub-carrier zero (lowest frequency bin). A bit set to 1 disables reception of the specified sub-carrier frequency bin end a 0 enables reception.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(32)  

adslLineDmtConfMode 1.3.6.1.2.1.10.94.1.1.16.2.1.15.1.3
Defines the operational mode of the DMT ADSL transceiver. Configured in the C-MSG1 and C-MSG-RA exchanges.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER echoCancel(1), freqDivMux(2)  

adslLineDmtConfTrellis 1.3.6.1.2.1.10.94.1.1.16.2.1.15.1.4
Enables the Trellis coder of the DMT transceiver. Configured in the C-MSG1 and C-MSG-RA exchanges.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

adslLineDmtConfEOC 1.3.6.1.2.1.10.94.1.1.16.2.1.15.1.5
Defines the embedded operations channel mode for the DMT ADSL line.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER byte(1), streaming(2)  

adslAtucDmtConfInterleavePath 1.3.6.1.2.1.10.94.1.1.16.2.1.15.1.6
Target channel for downstream interleave data path.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), as0(2), as1(3)  

adslAtucDmtConfFastPath 1.3.6.1.2.1.10.94.1.1.16.2.1.15.1.7
Target channel for downstream fast data path.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), as0(2), as1(3)  

adslAturDmtConfInterleavePath 1.3.6.1.2.1.10.94.1.1.16.2.1.15.1.8
Target channel for upstream interleave data path.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), ls0(2), ls1(3)  

adslAturDmtConfFastPath 1.3.6.1.2.1.10.94.1.1.16.2.1.15.1.9
Target channel for upstream fast data path.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER none(1), ls0(2), ls1(3)  

adslLineDmtAlarmConfProfileIndexNext 1.3.6.1.2.1.10.94.1.1.16.2.1.16
OBJECT IDENTIFIER    

adslLineDmtAlarmConfProfileTable 1.3.6.1.2.1.10.94.1.1.16.2.1.17
OBJECT IDENTIFIER    

adslDmtLineMIBNotificationsPrefix 1.3.6.1.2.1.10.94.1.1.16.2.2
OBJECT IDENTIFIER    

adslDmtLineMIBNotifications 1.3.6.1.2.1.10.94.1.1.16.2.2.0
OBJECT IDENTIFIER    

adslLineDmtMIBConformance 1.3.6.1.2.1.10.94.1.1.16.2.3
OBJECT IDENTIFIER    

adslLineDmtMIBCompliances 1.3.6.1.2.1.10.94.1.1.16.2.3.1
OBJECT IDENTIFIER    

adslLineDmtMIBGroups 1.3.6.1.2.1.10.94.1.1.16.2.3.2
OBJECT IDENTIFIER    

adslDMTLineMibCompliance 1.3.6.1.2.1.10.94.1.1.16.2.3.1.1
The compliance statement for SNMP entities which have ADSL DMT interfaces.
Status: current Access: read-create
MODULE-COMPLIANCE    

adslLineDmtMIBAturCompliance 1.3.6.1.2.1.10.94.1.1.16.2.3.1.2
The compliance statement for SNMP entities which manage ADSL DMT ATU-R interfaces.
Status: current Access: read-create
MODULE-COMPLIANCE    

adslLineDmtGroup 1.3.6.1.2.1.10.94.1.1.16.2.3.2.1
A collection of managed objects defining the attributes of an ADSL line supportings modems using the DMT line code.
Status: current Access: read-create
OBJECT-GROUP    

adslAtucDmtPhysGroup 1.3.6.1.2.1.10.94.1.1.16.2.3.2.2
A collection of managed objects defining the physical-layer parameters of an ATU-C using the DMT line code.
Status: current Access: read-create
OBJECT-GROUP    

adslAturDmtPhysGroup 1.3.6.1.2.1.10.94.1.1.16.2.3.2.3
A collection of managed objects defining the physical-layer parameters of an ATU-R using the DMT line code.
Status: current Access: read-create
OBJECT-GROUP    

adslLineDmtConfProfileGroup 1.3.6.1.2.1.10.94.1.1.16.2.3.2.4
A collection of managed objects defining the line configuration information associated with one or more ADSL ATU class devices implementing the DMT line code.
Status: current Access: read-create
OBJECT-GROUP