ADN-MIB

File: ADN-MIB.mib (1114826 bytes)

Imported modules

RFC1316-MIB RFC-1215 RFC1213-MIB
RFC-1212 RFC1155-SMI ATMF-CES
ATM-MIB RFC1406-MIB RFC1407-MIB
FRNETSERV-MIB IF-MIB SNMPv2-PARTY-MIB
SNMPv2-TC SNMPv2-SMI

Imported symbols

AutonomousType TRAP-TYPE PhysAddress
OBJECT-TYPE enterprises Counter
Gauge IpAddress atmfCESCbrIndex
atmVclVci atmVclVpi atmVplVpi
dsx1LineIndex dsx3LineIndex frPVCEndptDLCIIndex
ifAdminStatus ifOperStatus ifName
ifIndex InterfaceIndex contextEntry
partyIndex TimeStamp TruthValue
RowStatus DisplayString Integer32

Defined Types

AdnEquipType  
INTEGER other(1), node(2), card(3), interface(4), chassis(5), processor(6), iosPort(7), aeiPort(8)    

AdnCongestLevels  
INTEGER noconges(1), fecnbecn(2), drop2CIRcuf(3), discBe(4), discBeBcsnet(5), discBeBcsnetBcsusr(6), discBeBcsnetBcsusrBcusr(7), discBeBcsnetBcsusrBcusrBcnet(8), discBeBcsnetBcsusrBcusrBcnetUrg(9), notSignificant(10)    

AdnPercent  
INTEGER -2147483648..2147483647    

AdnEnableDisabled  
INTEGER enabled(1), disabled(2)    

AdnEnabDisabConn  
INTEGER enableConn(1), disableConn(2), useServiceValue(3), useCardValue(4)    

AdnFrtVCStates  
INTEGER no-calls(0), call-initiated(1), outgoing-call-proceeding(3), call-present(6), connect-request(8), callup(10), disconnect-request(11), disconnect-Indication(12), suspend-request(15), release-request(19)    

AdnNodeTimeTicks  
INTEGER    

AdnNodeTimeStamp  
AdnNodeTimeTicks    

AdnUpdateState  
INTEGER committed(1), commit-in-progress(2), activated(3), activate-in-progress(4), activate-pending(5)    

AdnRoutingID  
INTEGER    

AdnCouplerIndex  
INTEGER    

AdnEquipCause  
INTEGER none-value(1), other-reason(2), power-concern(4), fan-concern(8), temperature-concern(16), incorrect-type-of-board(32), incorrect-applique(64), absent-SAC-board(65), board-is-down(66), board-is-down-with-AEI-port-error(67), board-is-down-with-processor-error(68), board-returned-in-service(69), board-plugged-without-configuration(70), inaccessible-chassis(71), chassis-returned-in-service(72), hdlc-bus-driver-hardware-failure(73), hdlc-bus-connection-failure(74), board-is-down-after-NMGS-board-reset(75), board-is-down-after-NMS-board-reset(76), board-is-down-after-NMS-board-locking(77), board-unplugged(78), board-plugged(79), applique-absent(80), begin-of-board-hardware-test(100), end-of-board-hardware-test-without-error(101), end-of-board-hardware-test-with-error(102), hdlc-bus-hardware-failure-from-standby-CU(120), hdlc-bus-connection-failure-from-standby-CU(121), isl-bus-failure-from-standby-CU(122), unknown-state-from-standby-CU(123), wrong-HDLC-bus-cabling(124), standby-CU-configured-but-absent(200), board-aei-cabling-error(201), hardware-problem-on-LSN-link(202), hardware-problem-on-ISL(204), board-inaccessible-through-HDLC-bus(205), board-inaccessible-through-aei-link(206), cig-reset-after-bbase-plugging(207), board-going-out-of-supervision(208), board-entering-supervision(209), cu-version-error(210), cu-init-error(211), cu-hardware-error(212), cu-rebuild-error(213), board-is-down-due-to-hardware-key-reset(214), failure-of-on-board-49Mhz-oscillator(215), failure-of-on-board-3Mhz-NCO(216), loss-of-lock-in-3Mhz-phase-detector(217), loss-of-signal-52Mhz-VCXO(218), loss-of-signal-of-selected-52Mhz-reference(219), loss-of-lock-on-24Mhz-PLL(220), loss-of-lock-in-DS1-phase-detector(221), loss-of-DS1-clock-from-on-board-VCXO(222), inadvertent-reset-of-68331-microprocessor(223), oXo-oven-temperature-insufficiently-warm(224), loss-of-lock-in-2Mhz-phase-detector(225), loss-of-signal-on-2Mhz-reference-output(226), frequency-drift-outside-Stratum3E-limit(227), restart-for-other-reason(300), restart-on-NMS-request(301), restart-on-software-management-request(302), restart-on-HSS-internal-request(303), too-high-frequency-of-CU-restart(304), cu-switchover-with-hardware-key-down(305), cu-switchover-during-conf-processing(306)    

AdnRoutingMetricType  
INTEGER nullMetric(1), hopCount(2), transitDelay(3), monetaryCost(4)    

AdnRoutingCriteriaType  
OBJECT IDENTIFIER    

AdnFrCos  
INTEGER cosRt(1), cosNrt(2)    

AdnFrCosAdminStatus  
INTEGER unlocked(1), locked(2)    

AdnFrCosOperStatus  
INTEGER unlocked(1), locked(2)    

AdnFrChanEntry  
SEQUENCE    
  adnFrChanBAT AdnPercent
  adnFrChanAccounting AdnEnableDisabled
  adnFrChanStatistics AdnEnableDisabled
  adnFrChanLineType INTEGER
  adnFrChanCongsState AdnCongestLevels
  adnFrChanProced INTEGER
  adnFrChanVCTraps AdnEnableDisabled
  adnFrChanNxOverBcs INTEGER -2147483648..2147483647
  adnFrChanNxOverBe INTEGER -2147483648..2147483647
  adnFrChanInCIR INTEGER -2147483648..2147483647
  adnFrChanInBc INTEGER -2147483648..2147483647
  adnFrChanInBcs INTEGER -2147483648..2147483647
  adnFrChanInBe INTEGER -2147483648..2147483647
  adnFrChanOutCIR INTEGER -2147483648..2147483647
  adnFrChanOutBc INTEGER -2147483648..2147483647
  adnFrChanOutBcs INTEGER -2147483648..2147483647
  adnFrChanOutBe INTEGER -2147483648..2147483647
  adnFrChanNumCallActive INTEGER -2147483648..2147483647
  adnFrChanDelaySensitive TruthValue
  adnFrChanVCTypeConfigured INTEGER
  adnFrChanPVCMaxNumAllowed INTEGER -2147483648..2147483647
  adnFrChanPVCBidirLow INTEGER -2147483648..2147483647
  adnFrChanPVCBidirHigh INTEGER -2147483648..2147483647
  adnFrChanSVCMaxNumAllowed INTEGER -2147483648..2147483647
  adnFrChanSVCBidirLow INTEGER -2147483648..2147483647
  adnFrChanSVCBidirHigh INTEGER -2147483648..2147483647
  adnFrChanSVCUserNetFlg INTEGER
  adnFrChanSVCT303 INTEGER -2147483648..2147483647
  adnFrChanSVCT305 INTEGER -2147483648..2147483647
  adnFrChanSVCT308 INTEGER -2147483648..2147483647
  adnFrChanSVCT309 INTEGER -2147483648..2147483647
  adnFrChanSVCT310 INTEGER -2147483648..2147483647
  adnFrChanSVCT313 INTEGER -2147483648..2147483647
  adnFrChanSVCT315 INTEGER -2147483648..2147483647
  adnFrChanSVCT316 INTEGER -2147483648..2147483647
  adnFrChanSVCT317 INTEGER -2147483648..2147483647
  adnFrChanSVCT320 INTEGER -2147483648..2147483647
  adnFrChanSVCInCallBr AdnEnableDisabled
  adnFrChanSVCOutCallBr AdnEnableDisabled
  adnFrChanSVCAddrValid AdnEnableDisabled
  adnFrChanSVCAddrLenIg INTEGER -2147483648..2147483647
  adnFrChanSVCMaxNumActive INTEGER -2147483648..2147483647
  adnFrChanSVCCurrentActive INTEGER -2147483648..2147483647
  adnFrChanSVCTotalProcessed INTEGER -2147483648..2147483647
  adnFrChanSVCFailedClrNet INTEGER -2147483648..2147483647
  adnFrChanSVCFailedClrDTE INTEGER -2147483648..2147483647
  adnFrChanSVCSuccessClrNet INTEGER -2147483648..2147483647
  adnFrChanSVCSuccessClrDTE INTEGER -2147483648..2147483647
  adnFrChanSVCMaxAggActCIR INTEGER -2147483648..2147483647
  adnFrChanPVCMaxAggActCIR INTEGER -2147483648..2147483647
  adnFrChanSVCMaxAggNormBe INTEGER -2147483648..2147483647
  adnFrChanPVCMaxAggNormBe INTEGER -2147483648..2147483647
  adnFrChanDefaultCos AdnFrCos
  adnFrChanNumofMSN INTEGER -2147483648..2147483647
  adnFrChanNxMultiBc INTEGER -2147483648..2147483647
  adnFrChanMaxBcAllPVCs INTEGER -2147483648..2147483647
  adnFrChanMaxBcsAllPVCs INTEGER -2147483648..2147483647
  adnFrChanCosRtBcEgress INTEGER -2147483648..2147483647
  adnFrChanCosRtBcIngress INTEGER -2147483648..2147483647
  adnFrChanCosNrtBcEgress INTEGER -2147483648..2147483647
  adnFrChanCosNrtBcIngress INTEGER -2147483648..2147483647
  adnFrChanBwAllocated INTEGER -2147483648..2147483647
  adnFrChanBwAvail INTEGER -2147483648..2147483647

AdnFrVCEntry  
SEQUENCE    
  adnFrVCRemNodeID AdnRoutingID
  adnFrVCRemNumPlan INTEGER
  adnFrVCRemPhysAddress PhysAddress
  adnFrVCRemDlci INTEGER -2147483648..2147483647
  adnFrVCAdminState INTEGER
  adnFrVCOperState INTEGER
  adnFrVCTime AdnNodeTimeStamp
  adnFrVCInBcs INTEGER -2147483648..2147483647
  adnFrVCOutBcs INTEGER -2147483648..2147483647
  adnFrVCUserOrNet INTEGER
  adnFrVCLisDiscard INTEGER
  adnFrVCRetryAttempts INTEGER -2147483648..2147483647
  adnFrVCFastRetry INTEGER -2147483648..2147483647
  adnFrVCSlowRetry INTEGER -2147483648..2147483647
  adnFrVCForcedPath AdnEnableDisabled
  adnFrVCSourceDest INTEGER
  adnFrVCFrameIN Counter
  adnFrVCFrameOUT Counter
  adnFrVCSubFrameIN Counter
  adnFrVCSubFrameOUT Counter
  adnFrVCBeInDiscards Counter
  adnFrVCBcsInDiscards Counter
  adnFrVCBcInDiscards Counter
  adnFrVCBeOutDiscards Counter
  adnFrVCBcsOutDiscards Counter
  adnFrVCBcOutDiscards Counter
  adnFrVCInCongsState AdnCongestLevels
  adnFrVCDiscardLisIn Counter
  adnFrVCNumRelinks Counter
  adnFrVCNumNodes INTEGER -2147483648..2147483647
  adnFrVCType INTEGER
  adnFrVCOutifIndex InterfaceIndex
  adnFrVCOutDlci INTEGER -2147483648..2147483647
  adnFrVCISR INTEGER -2147483648..2147483647
  adnFrVCAttemptState INTEGER
  adnFrVCStatistics INTEGER
  adnFrVCAccounting INTEGER
  adnFrVCUniqueConnID INTEGER -2147483648..2147483647
  adnFrVCLastClrCauseRX INTEGER -2147483648..2147483647
  adnFrVCLastClrDiagRX INTEGER -2147483648..2147483647
  adnFrVCLastClrCauseTX INTEGER -2147483648..2147483647
  adnFrVCLastClrDiagTX INTEGER -2147483648..2147483647
  adnFrVCRemoteifindex INTEGER -2147483648..2147483647
  adnFrPVCEndptXmitdSigStatus INTEGER -2147483648..2147483647
  adnFrVCInBc INTEGER -2147483648..2147483647
  adnFrVCOutBc INTEGER -2147483648..2147483647
  adnFrVCRemNodeMacNum INTEGER -2147483648..2147483647
  adnFrVCRemNodeAreaNum INTEGER -2147483648..2147483647
  adnFrVCDelaySensitive TruthValue
  adnFrVCCos AdnFrCos
  adnFrVCEndptDLCIIndex INTEGER -2147483648..2147483647
  adnFrVCEndptInMaxFrameSize INTEGER -2147483648..2147483647
  adnFrVCEndptInBc INTEGER -2147483648..2147483647
  adnFrVCEndptInBe INTEGER -2147483648..2147483647
  adnFrVCEndptInCIR INTEGER -2147483648..2147483647
  adnFrVCEndptOutMaxFrameSize INTEGER -2147483648..2147483647
  adnFrVCEndptOutBc INTEGER -2147483648..2147483647
  adnFrVCEndptOutBe INTEGER -2147483648..2147483647
  adnFrVCEndptOutCIR INTEGER -2147483648..2147483647
  adnFrVCEndptConnectIdentifier INTEGER -2147483648..2147483647
  adnFrVCEndptRowStatus RowStatus
  adnFrVCEndptRcvdSigStatus INTEGER
  adnFrVCEndptInFrames Counter
  adnFrVCEndptOutFrames Counter
  adnFrVCEndptInDEFrames Counter
  adnFrVCEndptInExcessFrames Counter
  adnFrVCEndptOutExcessFrames Counter
  adnFrVCEndptInDiscards Counter
  adnFrVCEndptInOctets Counter
  adnFrVCEndptOutOctets Counter
  adnFrVCBwAllocated INTEGER -2147483648..2147483647
  adnFrVCDescr DisplayString

AdnCMBfvcAdnFrVCEntry  
SEQUENCE    
  adnCMBfvcadnFrVCRemNodeID AdnRoutingID
  adnCMBfvcadnFrVCRemNumPlan INTEGER
  adnCMBfvcadnFrVCRemPhysAddress PhysAddress
  adnCMBfvcadnFrVCRemDlci INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCAdminState INTEGER
  adnCMBfvcadnFrVCOperState INTEGER
  adnCMBfvcadnFrVCTime AdnNodeTimeStamp
  adnCMBfvcadnFrVCInBcs INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCOutBcs INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCUserOrNet INTEGER
  adnCMBfvcadnFrVCLisDiscard INTEGER
  adnCMBfvcadnFrVCRetryAttempts INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCFastRetry INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCSlowRetry INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCForcedPath AdnEnableDisabled
  adnCMBfvcadnFrVCSourceDest INTEGER
  adnCMBfvcadnFrVCFrameIN Counter
  adnCMBfvcadnFrVCFrameOUT Counter
  adnCMBfvcadnFrVCSubFrameIN Counter
  adnCMBfvcadnFrVCSubFrameOUT Counter
  adnCMBfvcadnFrVCBeInDiscards Counter
  adnCMBfvcadnFrVCBcsInDiscards Counter
  adnCMBfvcadnFrVCBcInDiscards Counter
  adnCMBfvcadnFrVCBeOutDiscards Counter
  adnCMBfvcadnFrVCBcsOutDiscards Counter
  adnCMBfvcadnFrVCBcOutDiscards Counter
  adnCMBfvcadnFrVCInCongsState AdnCongestLevels
  adnCMBfvcadnFrVCDiscardLisIn Counter
  adnCMBfvcadnFrVCNumRelinks Counter
  adnCMBfvcadnFrVCNumNodes INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCType INTEGER
  adnCMBfvcadnFrVCOutifIndex InterfaceIndex
  adnCMBfvcadnFrVCOutDlci INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCISR INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCAttemptState INTEGER
  adnCMBfvcadnFrVCStatistics INTEGER
  adnCMBfvcadnFrVCAccounting INTEGER
  adnCMBfvcadnFrVCUniqueConnID INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCLastClrCauseRX INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCLastClrDiagRX INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCLastClrCauseTX INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCLastClrDiagTX INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCRemoteifindex INTEGER -2147483648..2147483647
  adnCMBfvcadnFrPVCEndptXmitdSigStatus INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCInBc INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCOutBc INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCRemNodeMacNum INTEGER -2147483648..2147483647
  adnCMBfvcadnFrVCRemNodeAreaNum INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptDLCIIndex INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptInMaxFrameSize INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptInBc INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptInBe INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptInCIR INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptOutMaxFrameSize INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptOutBc INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptOutBe INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptOutCIR INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptConnectIdentifier INTEGER -2147483648..2147483647
  adnCMBfvcfrPVCEndptRowStatus RowStatus
  adnCMBfvcfrPVCEndptRcvdSigStatus INTEGER
  adnCMBfvcfrPVCEndptInFrames Counter
  adnCMBfvcfrPVCEndptOutFrames Counter
  adnCMBfvcfrPVCEndptInDEFrames Counter
  adnCMBfvcfrPVCEndptInExcessFrames Counter
  adnCMBfvcfrPVCEndptOutExcessFrames Counter
  adnCMBfvcfrPVCEndptInDiscards Counter
  adnCMBfvcfrPVCEndptInOctets Counter
  adnCMBfvcfrPVCEndptOutOctets Counter
  adnCMBfvcadnFrVCDelaySensitive TruthValue
  adnCMBfvcadnFrVCCos AdnFrCos
  adnCMBfvcadnFrVCDescr DisplayString

AdnFrForceEntry  
SEQUENCE    
  adnFrForceHop INTEGER -2147483648..2147483647
  adnFrForceNode AdnRoutingID
  adnFrForceFlag INTEGER
  adnFrForceOutifindex INTEGER -2147483648..2147483647
  adnFrFrcNodeMacNum INTEGER -2147483648..2147483647
  adnFrFrcNodeAreaNum INTEGER -2147483648..2147483647

AdnFrAccountVCEntry  
SEQUENCE    
  adnFrAccountTariff INTEGER -2147483648..2147483647
  adnFrAccountInSegments Counter
  adnFrAccountOutSegments Counter
  adnFrAccountInFrames Counter
  adnFrAccountOutFrames Counter
  adnFrAccountInExcessFrames Counter
  adnFrAccountOutExcessFrames Counter

AdnFrAccVCEntry  
SEQUENCE    
  adnFrAccVCifName DisplayString
  adnFrAccVCfrPVCEndptDLCIIndex INTEGER -2147483648..2147483647
  adnFrAccVCadnFrVCRemDlci INTEGER -2147483648..2147483647
  adnFrAccVCadnFrVCUniqueConnID INTEGER -2147483648..2147483647
  adnFrAccVCadnFrVCRemNodeID AdnRoutingID
  adnFrAccVCfrLportNumPlan INTEGER
  adnFrAccVCifPhysAddress PhysAddress
  adnFrAccVCadnFrVCRemNumPlan INTEGER
  adnFrAccVCadnFrVCRemPhysAddress PhysAddress
  adnFrAccVCadnFrVCSourceDest INTEGER
  adnFrAccVCadnFrVCNumRelinks INTEGER -2147483648..2147483647
  adnFrAccVCfrPVCEndptInCIR INTEGER -2147483648..2147483647
  adnFrAccVCadnFrVCInBc INTEGER -2147483648..2147483647
  adnFrAccVCadnFrVCInBcs INTEGER -2147483648..2147483647
  adnFrAccVCfrPVCEndptInBe INTEGER -2147483648..2147483647
  adnFrAccVCfrPVCEndptOutCIR INTEGER -2147483648..2147483647
  adnFrAccVCadnFrVCOutBc INTEGER -2147483648..2147483647
  adnFrAccVCadnFrVCOutBcs INTEGER -2147483648..2147483647
  adnFrAccVCfrPVCEndptOutBe INTEGER -2147483648..2147483647
  adnFrAccVCadnFrVCUserOrNet INTEGER
  adnFrAccVCfrAccountPVCSegmentSize INTEGER -2147483648..2147483647
  adnFrAccVCadnFrVCType INTEGER
  adnFrAccVCTimeEndAcct AdnNodeTimeStamp
  adnFrAccVCTimeStartAcct AdnNodeTimeStamp
  adnFrAccVCCallTerm INTEGER
  adnFrAccVCadnFrChanLineType INTEGER
  adnFrAccVCadnFrVCNumNodes INTEGER -2147483648..2147483647
  adnFrAccVCTableInSegments INTEGER -2147483648..2147483647
  adnFrAccVCTableInFrames INTEGER -2147483648..2147483647
  adnFrAccVCTableInExcessFrame INTEGER -2147483648..2147483647
  adnFrAccVCTableOutSegments INTEGER -2147483648..2147483647
  adnFrAccVCTableOutFrames INTEGER -2147483648..2147483647
  adnFrAccVCTableOutExcessFrame INTEGER -2147483648..2147483647
  adnFrAccVCPVCRegroomed TruthValue
  adnFrAccVCSVCCallingPartyNum PhysAddress
  adnFrAccVCSVCCalledPartyNum PhysAddress
  adnFrAccVCSVCCallEstablished TruthValue
  adnFrAccVCSVCQ933ClearingCause INTEGER -2147483648..2147483647
  adnFrAccVCSVCQ933ClearingLocation INTEGER -2147483648..2147483647
  adnFrAccVCCos AdnFrCos
  adnFrAccVCadnFrVCLocalNodeID AdnRoutingID
  adnFrAccVCadnFrVCDescr DisplayString
  adnFrAccVCadnFrVCLocalifIndex INTEGER -2147483648..2147483647
  adnFrAccVCadnFrVCRemoteifIndex InterfaceIndex
  adnFrAccVCadnFrVCEndptInDiscards INTEGER -2147483648..2147483647
  adnFrAccVCifSpeed Gauge
  adnFrAccVCadnNodeTime AdnNodeTimeTicks

AdnFrStatVCEntry  
SEQUENCE    
  adnFrStatVCifName DisplayString
  adnFrStatVCadnFrVCRemoteifindex INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCRemDlci INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCUniqueConnID INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCRemNodeID AdnRoutingID
  adnFrStatVCfrLportNumPlan INTEGER
  adnFrStatVCifPhysAddress PhysAddress
  adnFrStatVCadnFrVCRemNumPlan INTEGER
  adnFrStatVCadnFrVCRemPhysAddress PhysAddress
  adnFrStatVCadnFrVCSourceDest INTEGER
  adnFrStatVCadnFrVCNumRelinks INTEGER -2147483648..2147483647
  adnFrStatVCfrPVCEndptInCIR INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCInBc INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCInBcs INTEGER -2147483648..2147483647
  adnFrStatVCfrPVCEndptInBe INTEGER -2147483648..2147483647
  adnFrStatVCfrPVCEndptOutCIR INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCOutBc INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCOutBcs INTEGER -2147483648..2147483647
  adnFrStatVCfrPVCEndptOutBe INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCISR INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCUserOrNet INTEGER
  adnFrStatVCfrAccountPVCSegmentSize INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCType INTEGER
  adnFrStatVCadnNodeTime AdnNodeTimeTicks
  adnFrStatVCadnFrVCAdminState INTEGER
  adnFrStatVCadnFrVCOperState INTEGER
  adnFrStatVCadnFrVCFrameIN INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCFrameOUT INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCSubFrameIN INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCSubFrameOUT INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCBeInDiscards INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCBcsInDiscards INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCBcInDiscards INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCBeOutDiscards INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCBcsOutDiscards INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCBcOutDiscards INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCDiscardLisIn INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCInCongsState AdnCongestLevels
  adnFrStatVCfrPVCEndptDLCIIndex INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCNumNodes INTEGER -2147483648..2147483647
  adnFrStatVCfrPVCEndptInOctets INTEGER -2147483648..2147483647
  adnFrStatVCfrPVCEndptOutOctets INTEGER -2147483648..2147483647
  adnFrStatVCadnFrVCDescr DisplayString

AdnFrReachAddrEntry  
SEQUENCE    
  adnFrReachAddrIndex INTEGER
  adnFrReachAddrNumPlan INTEGER
  adnFrReachAddrNumberLength INTEGER
  adnFrReachAddrNumber PhysAddress

AdnFrCosEntry  
SEQUENCE    
  adnFrCosIndex AdnFrCos
  adnFrCosAdminStatus AdnFrCosAdminStatus
  adnFrCosOperStatus AdnFrCosOperStatus

AdnIfTestEntry  
SEQUENCE    
  adnIfTestTimeLimit INTEGER -2147483648..2147483647
  adnIfTestFailLevel INTEGER -2147483648..2147483647
  adnIfTestBitsSentHi Counter
  adnIfTestBitsSentLo Counter
  adnIfTestBitsReceivedHi Counter
  adnIfTestBitsReceivedLo Counter
  adnIfTestBitsErroredHi Counter
  adnIfTestBitsErroredLo Counter
  adnIfTestStartTime TimeStamp
  adnIfTestStopTime TimeStamp

AdnIfEntry  
SEQUENCE    
  adnIfInstallStatus INTEGER
  adnIfControlStatus INTEGER
  adnIfSubType INTEGER

AdnEquipEntry  
SEQUENCE    
  adnEquipType AdnEquipType
  adnEquipIndex INTEGER
  adnEquipSubType AutonomousType
  adnEquipLastChange TimeStamp
  adnEquipInitTime TimeStamp
  adnEquipTrapEnableMask INTEGER
  adnEquipX731Oper INTEGER
  adnEquipX731Admin INTEGER
  adnEquipX731Usage INTEGER
  adnEquipX731Avail INTEGER
  adnEquipInstallStatus INTEGER
  adnEquipControlStatus INTEGER
  adnEquipControlHistory INTEGER
  adnEquipControlOptions INTEGER
  adnEquipSwitchoverOptions INTEGER
  adnEquipTrapCause INTEGER
  adnEquipX731StandbyStatus INTEGER
  adnEquipSwitchbackOptions INTEGER

AdnContainEntry  
SEQUENCE    
  adnContainerType AdnEquipType
  adnContainerIndex INTEGER
  adnContainedType AdnEquipType
  adnContainedIndex INTEGER
  adnContainerPosition INTEGER

AdnNodeEntry  
SEQUENCE    
  adnNodeIndex INTEGER
  adnNodeDescr DisplayString
  adnNodeContact DisplayString
  adnNodeName DisplayString
  adnNodeLocation DisplayString
  adnNodeServices INTEGER
  adnNodeNumPlan INTEGER
  adnNodeAddress PhysAddress
  adnNodeClockRefresh INTEGER
  adnNodeRoutingID AdnRoutingID
  adnNodeMaxChassis INTEGER
  adnNodeMachineNumber INTEGER
  adnNodeAreaNumber INTEGER
  adnNodeNetworkType INTEGER
  adnNodeAtmNetPloss INTEGER
  adnNodeConfigFrom INTEGER

AdnCongMgmtChanEntry  
SEQUENCE    
  adnCongMgmtChanCUFValue Counter

AdnCongMgmtVCEntry  
SEQUENCE    
  adnCongMgmtVCDLCIIndex Integer32
  adnCongMgmtVCBcInDiscards Counter
  adnCongMgmtVCBcsInDiscards Counter
  adnCongMgmtVCBeInDiscards Counter
  adnCongMgmtVCInBcSubfrmSent Counter
  adnCongMgmtVCInBcsSubfrmSent Counter
  adnCongMgmtVCInBeSubfrmSent Counter
  adnCongMgmtVCInCongsState AdnCongestLevels
  adnCongMgmtVCCurrentSIR INTEGER -2147483648..2147483647

AdnIsnaIcEntry  
SEQUENCE    
  adnIsnaIcifIndex INTEGER -2147483648..2147483647
  adnIsnaIcDlci INTEGER -2147483648..2147483647
  adnIsnaIcType INTEGER
  adnIsnaIcBckIfindex INTEGER -2147483648..2147483647
  adnIsnaIcBckDlci INTEGER -2147483648..2147483647
  adnIsnaIcAdminState INTEGER
  adnIsnaIcOperState INTEGER

AdnIsnaRouteIpEntry  
SEQUENCE    
  adnIsnaRouteifIndex INTEGER -2147483648..2147483647
  adnIsnaRouteDlci INTEGER -2147483648..2147483647
  adnIsnaRouteIpAddrs IpAddress
  adnIsnaRouteIpMask IpAddress

AdnIsomVcEntry  
SEQUENCE    
  adnIsomVcifIndex INTEGER -2147483648..2147483647
  adnIsomVcOutDlci INTEGER -2147483648..2147483647
  adnIsomVcAdminState INTEGER
  adnIsomVcOperState INTEGER
  adnIsomVcTime AdnNodeTimeStamp

AdnIsomTrapIpEntry  
SEQUENCE    
  adnIsomTrapifIndex INTEGER -2147483648..2147483647
  adnIsomTrapDlci INTEGER -2147483648..2147483647
  adnIsomTrapIpAddrs IpAddress

AdnRoutesNumPlan  
INTEGER x121(1), e164(2), atmInternal(3), atmPrivate(4), other(5)    

AdnCalcMonEntry  
SEQUENCE    
  adntosIndex INTEGER
  adncriterionIndex INTEGER
  adnMaxPath INTEGER
  adnMaxCost INTEGER -2147483648..2147483647
  adnMinTimeBetCalc INTEGER -2147483648..2147483647

AdnMessMonEntry  
SEQUENCE    
  adnMinTimeBetLS INTEGER -2147483648..2147483647
  adnbroadcastLSU INTEGER
  adnLSUbroadcastfreez INTEGER
  adnTblDistfreez INTEGER

AdnManNPhdrEntry  
SEQUENCE    
  adnManNPhdrVer INTEGER
  adnManNPhdrStamp AdnNodeTimeStamp
  adnManNPhdrNum INTEGER -2147483648..2147483647

AdnManNPPathhdrEntry  
SEQUENCE    
  adnManDnodeIndex AdnRoutingID
  adnManNPhdrNumPth INTEGER
  adnManRemNodeMacNum INTEGER -2147483648..2147483647
  adnManRemNodeAreaNum INTEGER -2147483648..2147483647

AdnManNPpthEntry  
SEQUENCE    
  adnManPathIndex INTEGER
  adnManNPpthCost INTEGER -2147483648..2147483647
  adnManNPpthAJid AdnRoutingID
  adnManNPpthIpAdr IpAddress

AdnCurNPhdrEntry  
SEQUENCE    
  adntosIndex INTEGER
  adncriterionIndex INTEGER
  adnCurNPhdrVer INTEGER
  adnCurNPhdrStamp AdnNodeTimeStamp
  adnCurNPhdrNum INTEGER -2147483648..2147483647

AdnCurNPPathhdrEntry  
SEQUENCE    
  adnCurDnodeIndex AdnRoutingID
  adnCurNPhdrIpAdr IpAddress
  adnCurNPhdrNumPth INTEGER
  adnCurRemNodeMacNum INTEGER -2147483648..2147483647
  adnCurRemNodeAreaNum INTEGER -2147483648..2147483647

AdnCurNPpthEntry  
SEQUENCE    
  adnCurPathIndex INTEGER
  adnCurNPpthCost INTEGER -2147483648..2147483647
  adnCurNPpthAJid AdnRoutingID

AdnManAjhdrEntry  
SEQUENCE    
  adnManAjhdrVer INTEGER
  adnManAjhdrStamp AdnNodeTimeStamp
  adnManAjhdrNum INTEGER -2147483648..2147483647

AdnManAjLinehdrEntry  
SEQUENCE    
  adnManAnodeIndex AdnRoutingID
  adnAJManNumLines INTEGER
  adnManAjNodeMacNum INTEGER -2147483648..2147483647
  adnManAjNodeAreaNum INTEGER -2147483648..2147483647

AdnManAjLineEntry  
SEQUENCE    
  adnAJManLocIfIndex INTEGER -2147483648..2147483647
  adnAJManMetricCost1 INTEGER -2147483648..2147483647
  adnAJManMetricCost2 INTEGER -2147483648..2147483647
  adnAJManMetricCost3 INTEGER -2147483648..2147483647
  adnAJManRemIfIndex INTEGER -2147483648..2147483647

AdnCurAjhdrEntry  
SEQUENCE    
  adnCurAjhdrVer INTEGER
  adnCurAjhdrStamp AdnNodeTimeStamp
  adnCurAjhdrNum INTEGER -2147483648..2147483647

AdnCurAjLinehdrEntry  
SEQUENCE    
  adnCurAnodeIndex AdnRoutingID
  adnAJCurNodetype INTEGER
  adnAJCurNumLines INTEGER
  adnAJCurNxtLine INTEGER
  adnAJNState INTEGER
  adnCurAjNodeMacNum INTEGER -2147483648..2147483647
  adnCurAjNodeAreaNum INTEGER -2147483648..2147483647

AdnCurAjLineEntry  
SEQUENCE    
  adnAJCurLocIfIndex INTEGER -2147483648..2147483647
  adnAJCurMetricCost1 INTEGER -2147483648..2147483647
  adnAJCurMetricCost2 INTEGER -2147483648..2147483647
  adnAJCurMetricCost3 INTEGER -2147483648..2147483647
  adnAJCurRemIfIndex INTEGER -2147483648..2147483647

AdnLahdrEntry  
SEQUENCE    
  adnNumPlanIndex AdnRoutesNumPlan
  adnLahdrVer INTEGER
  adnLahdrStamp AdnNodeTimeStamp
  adnLahdrNum INTEGER -2147483648..2147483647

AdnLaEntry  
SEQUENCE    
  adnLaAdIndex OCTET STRING
  adnLaIfIndex INTEGER -2147483648..2147483647

AdnAnhdrEntry  
SEQUENCE    
  adnAnhdrNumPlanIndex AdnRoutesNumPlan
  adnAnhdrVer INTEGER
  adnAnhdrStamp AdnNodeTimeStamp
  adnAnhdrNum INTEGER -2147483648..2147483647

AdnAnEntry  
SEQUENCE    
  adnAnNumPlanIndex AdnRoutesNumPlan
  adnAnAdIndex OCTET STRING
  adnAnNodeIndex AdnRoutingID
  adnAnRank INTEGER
  adnAnNodeMacNum INTEGER -2147483648..2147483647
  adnAnNodeAreaNum INTEGER -2147483648..2147483647
  adnAnPartialAddrFlag INTEGER
  adnAnAddrLength INTEGER

AdnStatsNodeEntry  
SEQUENCE    
  adnStatsTotLSU INTEGER -2147483648..2147483647
  adnStatsTotDupLSU INTEGER -2147483648..2147483647
  adnStatsTotOldLSU INTEGER -2147483648..2147483647

AdnRtsCritSmryEntry  
SEQUENCE    
  adnRtsCritID INTEGER -2147483648..2147483647
  adnRtsCritOID AdnRoutingCriteriaType
  adnRtsCritMetricHigh AdnRoutingMetricType
  adnRtsCritMetricMid AdnRoutingMetricType
  adnRtsCritMetricLow AdnRoutingMetricType

AdnCalcCtlEntry  
SEQUENCE    
  adnTosIndex INTEGER
  adnMaxNumPath INTEGER -2147483648..2147483647
  adnMinTimeBtwCalc INTEGER -2147483648..2147483647
  adnMetricDefHigh INTEGER -2147483648..2147483647
  adnMetricMaxHigh INTEGER -2147483648..2147483647
  adnMetricDefMid INTEGER -2147483648..2147483647
  adnMetricMaxMid INTEGER -2147483648..2147483647
  adnMetricDefLow INTEGER -2147483648..2147483647
  adnMetricMaxLow INTEGER -2147483648..2147483647

AdnNPhdrEntry  
SEQUENCE    
  adnNPhdrVer INTEGER
  adnNPhdrStamp AdnNodeTimeStamp
  adnNPhdrNum INTEGER -2147483648..2147483647

AdnNPPathhdrEntry  
SEQUENCE    
  adnDnodeIndex AdnRoutingID
  adnNPhdrIpAdr IpAddress
  adnNPhdrNumPth INTEGER -2147483648..2147483647
  adnRemNodeMacNum INTEGER -2147483648..2147483647
  adnRemNodeAreaNum INTEGER -2147483648..2147483647

AdnNodePathEntry  
SEQUENCE    
  adnNodePathIndex INTEGER -2147483648..2147483647
  adnNodePathAdjNodeID AdnRoutingID
  adnNodePathCostHigh INTEGER -2147483648..2147483647
  adnNodePathCostMid INTEGER -2147483648..2147483647
  adnNodePathCostLow INTEGER -2147483648..2147483647
  adnNodePathRemNodeMacNum INTEGER -2147483648..2147483647
  adnNodePathRemNodeAreaNum INTEGER -2147483648..2147483647

AdnAdjhdrEntry  
SEQUENCE    
  adnAdjhdrVer INTEGER -2147483648..2147483647
  adnAdjhdrStamp AdnNodeTimeStamp
  adnAdjhdrNum INTEGER -2147483648..2147483647

AdnAjLinehdrEntry  
SEQUENCE    
  adnAnodeIndex AdnRoutingID
  adnAdjNodetype INTEGER
  adnAdjNumLines INTEGER
  adnAdjNxtLine INTEGER
  adnAdjNodeState INTEGER
  adnAdjRemNodeMacNum INTEGER -2147483648..2147483647
  adnAdjRemNodeAreaNum INTEGER -2147483648..2147483647
  adnAdjTpxAddr OCTET STRING
  adnAdjhdrIpAdr IpAddress

AdnAdjLineEntry  
SEQUENCE    
  adnAdjLocIfIndex INTEGER -2147483648..2147483647
  adnAdjRemIfIndex INTEGER -2147483648..2147483647
  adnAdjMetricIDHigh AdnRoutingMetricType
  adnAdjMetricCostHigh INTEGER -2147483648..2147483647
  adnAdjMetricIDMid AdnRoutingMetricType
  adnAdjMetricCostMid INTEGER -2147483648..2147483647
  adnAdjMetricIDLow AdnRoutingMetricType
  adnAdjMetricCostLow INTEGER -2147483648..2147483647
  adnAdjRemTpxTci INTEGER

AdnMsgMonEntry  
SEQUENCE    
  adnRtsMinTimeBetLS INTEGER -2147483648..2147483647
  adnRtsbroadcastLSU INTEGER
  adnRtsLSUbroadcastfreez INTEGER
  adnRtsTblDistfreez INTEGER

AdnRtsMHStatsEntry  
SEQUENCE    
  adnRtsMHTotLSU INTEGER -2147483648..2147483647
  adnRtsMHTotDupLSU INTEGER -2147483648..2147483647
  adnRtsMHTotOldLSU INTEGER -2147483648..2147483647

AdnLocalAddrEntry  
SEQUENCE    
  adnLocalAddrIndex OCTET STRING
  adnLocalAddrNumIfIndex INTEGER -2147483648..2147483647
  adnLocalAddrIfIndex INTEGER -2147483648..2147483647

AdnViewEntry  
SEQUENCE    
  adnViewIndex INTEGER -2147483648..2147483647

AdnCnmEntry  
SEQUENCE    
  adnCnmIndex INTEGER
  adnCnmIfIndex INTEGER -2147483648..2147483647
  adnCnmAccess INTEGER
  adnCnmType INTEGER

AdnSaLoggedTrapEntry  
SEQUENCE    
  adnSaLoggedTrapPartyIndex INTEGER
  adnSaLoggedTrapIndex INTEGER
  adnSaLoggedTrapCategory INTEGER

AdnSaLoggedTrapReplayEntry  
SEQUENCE    
  adnSaLoggedTrapReplayPartyIndex INTEGER
  adnSaLoggedTrapReplayFirst INTEGER
  adnSaLoggedTrapReplayLast INTEGER
  adnSaLoggedTrapReplayOn AdnEnableDisabled

AdnLdrChanEntry  
SEQUENCE    
  adnLdrChanType INTEGER
  adnLdrChanStatisticsFlag AdnEnableDisabled
  adnLdrChanSubFrameIN Counter
  adnLdrChanAbortIN Counter
  adnLdrChanCrcErrIN Counter
  adnLdrChanOverRunErrIN Counter
  adnLdrChanOctetAlignErrIN Counter
  adnLdrChanBusyErrIN Counter
  adnLdrChanAbortOUT Counter
  adnLdrChanUnderRunErrOUT Counter
  adnLdrChanNumOfFlags INTEGER
  adnLdrChanFlagOrIdle INTEGER
  adnLdrChanTimeSlotMask INTEGER
  adnLdrChanFramed INTEGER
  adnLdrChanCosRtOutOctets Counter
  adnLdrChanCosRtOutPkts Counter
  adnLdrChanCosRtOutErrors Counter
  adnLdrChanCosNrtOutOctets Counter
  adnLdrChanCosNrtOutPkts Counter
  adnLdrChanCosNrtOutErrors Counter

AdnDumDirectoryEntry  
SEQUENCE    
  adnDumDirectoryIndex INTEGER
  adnDumDirectoryPathname DisplayString
  adnDumDirectoryPercentUsage AdnPercent
  adnDumDirectoryLevelUsage INTEGER
  adnDumUsageThresholds INTEGER

AdnDumSubdirectoryEntry  
SEQUENCE    
  adnDumDirectoryIndex INTEGER
  adnDumSubdirectoryIndex INTEGER
  adnDumSubdirectoryPathname DisplayString
  adnDumSubdirectoryQuota AdnPercent

AdnCuCodeUpdateCntlEntry  
SEQUENCE    
  adnCuCodeServiceIdIndex INTEGER -2147483648..2147483647
  adnCuCodeOperStatus INTEGER
  adnCuCodeState INTEGER

AdnCuConfigUpdateCntlEntry  
SEQUENCE    
  adnCuConfigApplIdIndex INTEGER
  adnCuConfigOperStatus INTEGER
  adnCuConfigState INTEGER
  adnCuConfigFileName OCTET STRING
  adnCuConfigNextFileName OCTET STRING

AdnProcCodeUpdateCntlEntry  
SEQUENCE    
  adnProcCodeChassisIndex INTEGER -2147483648..2147483647
  adnProcCodeSlotIndex INTEGER -2147483648..2147483647
  adnProcCodeProcessorIndex INTEGER -2147483648..2147483647
  adnProcCodeOperStatus INTEGER
  adnProcCodeState INTEGER

AdnBrdConfigUpdateCntlEntry  
SEQUENCE    
  adnBrdConfigChassisIndex INTEGER -2147483648..2147483647
  adnBrdConfigSlotIndex INTEGER -2147483648..2147483647
  adnBrdConfigOperStatus INTEGER
  adnBrdConfigState INTEGER
  adnBrdConfigFileName OCTET STRING
  adnBrdConfigNextFileName OCTET STRING
  adnBrdConfigNoCfgOrFullCfg INTEGER

AdnBrdFlashContentListEntry  
SEQUENCE    
  adnBrdFlashChassisIndex INTEGER -2147483648..2147483647
  adnBrdFlashSlotIndex INTEGER -2147483648..2147483647
  adnBrdFlashSize INTEGER -2147483648..2147483647
  adnBrdFlashVolume1 DisplayString
  adnBrdFlashVolume2 DisplayString
  adnBrdFlashVolume3 DisplayString
  adnBrdFlashVolume4 DisplayString

Adn3rdPartyCardEntry  
SEQUENCE    
  adn3rdPartyCardDescr DisplayString
  adn3rdPartyCardLocAddrType INTEGER
  adn3rdPartyCardLocAddress PhysAddress

AdnClockConfigEntry  
SEQUENCE    
  adnClockIfIndex INTEGER
  adnClockType INTEGER
  adnClockStatus INTEGER
  adnClockSource INTEGER

AdnAppliqueType  
INTEGER other(1), ha8rs(2), ha8x1(3), ha8v3(4), ha8v6(5), ha2t1(6), ha2e1(7), hacig(8), hat3b(9), hae3b(10), has1b(11), hacmi(12), hae1b(13), hat1b(14), hacui1(15), hacui2(16), haase1(17), haase2(18), ha2et(19), ha2tr(20), hammb(21), hacige(22), ha8ct(23), ha8ce(24), havft(25), havfe(26), hard1(27), hasyn(28), hacui3(29), ha2e1b(30), hae1bb(31), ha8ceb(32), havfeb(33), ha4vt(34), ha4ve(35), has1b3(36), has4b(37), has4b3(38), hats1c(39), hatt3c(40), hate3c(41), hacmic(42), hatmfc(43), hatl1c(44)    

AdnChassisEntry  
SEQUENCE    
  adnChassisStatus INTEGER
  adnChassisOperFanId INTEGER
  adnChassisPresentFanId INTEGER
  adnChassisOperPowerId INTEGER
  adnChassisPresentPowerId INTEGER
  adnChassisSlotNumber INTEGER
  adnChassisPrimaryMSC8kSourceIfIndex INTEGER
  adnChassisBackupMSC8kSourceIfIndex INTEGER
  adnChassisMidplaneClockStatus INTEGER
  adnChassisClockPropagationStatus INTEGER
  adnChassisRABUsage INTEGER
  adnChassisStandbyCUBusStatus INTEGER

AdnBoardEntry  
SEQUENCE    
  adnBoardAppliqueType AdnAppliqueType
  adnBoardAppliqueState INTEGER
  adnBoardApplPluggedType AdnAppliqueType
  adnBoardPluggedType AutonomousType
  adnBoardRedundancyRole INTEGER
  adnBoardRedundancyStatus INTEGER
  adnBoardRedundancyFailure INTEGER
  adnBoardRedundantBind INTEGER
  adnBoardSwitchCause INTEGER
  adnBoardFaultStatus INTEGER
  adnBoardServiceIndicator INTEGER
  adnBoardTestResult INTEGER

AdnEepromEntry  
SEQUENCE    
  adnEepromSerialNumber DisplayString
  adnEepromBoardName DisplayString
  adnEepromPartNumberAndVariant DisplayString
  adnEepromIcs DisplayString
  adnEepromIcsChangeDate DisplayString
  adnEepromFlashIdentifier DisplayString
  adnEepromLastRepairDate DisplayString
  adnEepromWarrantyEndDate DisplayString

AdnAeiPortEntry  
SEQUENCE    
  adnAeiPortActiveOrNot INTEGER
  adnAeiPortErOrWngStatus INTEGER
  adnAeiPortStatus INTEGER
  adnAeiPortTestResult INTEGER
  adnAeiPortLinkId INTEGER

AdnProcessorEntry  
SEQUENCE    
  adnProcessorErOrWngStatus INTEGER -2147483648..2147483647
  adnProcessorStatus INTEGER -2147483648..2147483647

AdnIfAssignmentEntry  
SEQUENCE    
  adnIfAssignmentChassis INTEGER
  adnIfAssignmentSlot INTEGER
  adnIfAssignmentLine INTEGER -2147483648..2147483647
  adnIfAssignmentCtrlAppli INTEGER -2147483648..2147483647
  adnIfAssignmentLowIndex InterfaceIndex
  adnIfAssignmentTSI INTEGER

AdnIpAddrAssignmentEntry  
SEQUENCE    
  adnIpAddress IpAddress
  adnIpAddrAssignmentIfindex INTEGER -2147483648..2147483647

AdnPhyEntry  
SEQUENCE    
  adnPhyChassis INTEGER
  adnPhySlot INTEGER
  adnPhyLine INTEGER
  adnPhyChannel INTEGER

AdnPmdNodeEntry  
SEQUENCE    
  adnPmdNodeEnableDisable INTEGER
  adnPmdNodeKindOfPmd INTEGER
  adnPmdNodeSurveillance INTEGER
  adnPmdNodeFilterStatus INTEGER

AdnPmdBoardEntry  
SEQUENCE    
  adnPmdBoardEnableDisable INTEGER
  adnPmdBoardKindOfPmd INTEGER
  adnPmdBoardFilterStatus INTEGER

AdnPmdProcessorEntry  
SEQUENCE    
  adnPmdProcessorEnableDisable INTEGER
  adnPmdProcessorKindOfPmd INTEGER
  adnPmdProcessorFilterStatus INTEGER

AdnFrtChanEntry  
SEQUENCE    
  adnFrtChanType INTEGER
  adnFrtChanAddrDLCILen INTEGER
  adnFrtChanRNodeID AdnRoutingID
  adnFrtChanRifIndex InterfaceIndex
  adnFrtChanBAT AdnPercent
  adnFrtChanNxOverBcsUser INTEGER -2147483648..2147483647
  adnFrtChanNxOverBcsNet INTEGER -2147483648..2147483647
  adnFrtChanNxOverBe INTEGER -2147483648..2147483647
  adnFrtChanMaxBcsUser AdnPercent
  adnFrtChanMaxBcsNet AdnPercent
  adnFrtChanMaxBe AdnPercent
  adnFrtChanMaxCrf INTEGER -2147483648..2147483647
  adnFrtChanMinDlci INTEGER -2147483648..2147483647
  adnFrtChanMaxDlci INTEGER -2147483648..2147483647
  adnFrtChanTotalNumDlci INTEGER -2147483648..2147483647
  adnFrtChanUserNetFlg INTEGER
  adnFrtChanTPXBc2HSSBcsUsr INTEGER
  adnFrtChanTPXBc2HSSBcsNet INTEGER
  adnFrtChanStatistics AdnEnableDisabled
  adnFrtChanT303 INTEGER -2147483648..2147483647
  adnFrtChanT305 INTEGER -2147483648..2147483647
  adnFrtChanT308 INTEGER -2147483648..2147483647
  adnFrtChanT309 INTEGER -2147483648..2147483647
  adnFrtChanT310 INTEGER -2147483648..2147483647
  adnFrtChanT313 INTEGER -2147483648..2147483647
  adnFrtChanT315 INTEGER -2147483648..2147483647
  adnFrtChanT316 INTEGER -2147483648..2147483647
  adnFrtChanT317 INTEGER -2147483648..2147483647
  adnFrtChanT320 INTEGER -2147483648..2147483647
  adnFrtChanNxOverBeControl AdnEnableDisabled
  adnFrtChanMonetaryCost INTEGER -2147483648..2147483647
  adnFrtChanDelayMeasured INTEGER -2147483648..2147483647
  adnFrtChanDelayInUse INTEGER -2147483648..2147483647
  adnFrtChanDelayReMeasReq INTEGER
  adnFrtChanDefaultCos AdnFrCos
  adnFrtChanPerDlyIntrv INTEGER
  adnFrtChanTotalUsrPVCsUp INTEGER -2147483648..2147483647
  adnFrtChanTotalUsrSVCsUp INTEGER -2147483648..2147483647

AdnFrtCosEntry  
SEQUENCE    
  adnFrtCosIndex AdnFrCos
  adnFrtCosAdminStatus AdnFrCosAdminStatus
  adnFrtCosOperStatus AdnFrCosOperStatus

AdnFrtChanStatsEntry  
SEQUENCE    
  adnFrtChanStatsCommitEgress INTEGER -2147483648..2147483647
  adnFrtChanStatsCommitIngress INTEGER -2147483648..2147483647
  adnFrtChanStatsOverEgress INTEGER -2147483648..2147483647
  adnFrtChanStatsOverIngress INTEGER -2147483648..2147483647
  adnFrtChanStatsBcInDiscards Counter
  adnFrtChanStatsBcsInDiscards Counter
  adnFrtChanStatsBeInDiscards Counter
  adnFrtChanStatsBcOutDiscards Counter
  adnFrtChanStatsBcsOutDiscards Counter
  adnFrtChanStatsBeOutDiscards Counter
  adnFrtChanStatsCongsState AdnCongestLevels
  adnFrtChanStatsCosRtBcEgress INTEGER -2147483648..2147483647
  adnFrtChanStatsCosRtBcIngress INTEGER -2147483648..2147483647
  adnFrtChanStatsCosNrtBcEgress INTEGER -2147483648..2147483647
  adnFrtChanStatsCosNrtBcIngress INTEGER -2147483648..2147483647

AdnFrtVCEntry  
SEQUENCE    
  adnFrtVCDLCIIndex INTEGER -2147483648..2147483647
  adnFrtVCSetupDir INTEGER
  adnFrtVCAdminState INTEGER
  adnFrtVCOperState INTEGER
  adnFrtVCForcedPath INTEGER
  adnFrtVCTrafficType INTEGER
  adnFrtVCState INTEGER
  adnFrtVCRemoteDlci INTEGER -2147483648..2147483647
  adnFrtVCRemoteDlciLen INTEGER -2147483648..2147483647
  adnFrtVCRemoteifIndex InterfaceIndex
  adnFrtVCAdjacentNodeID AdnRoutingID
  adnFrtVCAdjacentifIndex InterfaceIndex
  adnFrtVCBcForward INTEGER -2147483648..2147483647
  adnFrtVCBcBackward INTEGER -2147483648..2147483647
  adnFrtVCBeForward INTEGER -2147483648..2147483647
  adnFrtVCBeBackward INTEGER -2147483648..2147483647
  adnFrtVCBcsForward INTEGER -2147483648..2147483647
  adnFrtVCBcsBackward INTEGER -2147483648..2147483647
  adnFrtVCCirForward INTEGER -2147483648..2147483647
  adnFrtVCCirBackward INTEGER -2147483648..2147483647
  adnFrtVCDelayCostRem INTEGER -2147483648..2147483647
  adnFrtVCMonetaryCostRem INTEGER -2147483648..2147483647
  adnFrtVCHopCostRem INTEGER -2147483648..2147483647
  adnFrtVCRoutingMode INTEGER
  adnFrtVCPathSelectMode INTEGER
  adnFrtVCRtsCritID INTEGER
  adnFrtVCType INTEGER
  adnFrtVCCos AdnFrCos

AdnFrtVCStatsEntry  
SEQUENCE    
  adnFrtVCStatsTime AdnNodeTimeStamp
  adnFrtVCStatsSubFrameIN Counter
  adnFrtVCStatsSubFrameOUT Counter
  adnFrtVCStatsBcOutDiscards Counter
  adnFrtVCStatsBcsOutDiscards Counter
  adnFrtVCStatsBeOutDiscards Counter
  adnFrtVCStatsIWFBcInDiscards Counter
  adnFrtVCStatsIWFBcsInDiscards Counter
  adnFrtVCStatsIWFBeInDiscards Counter
  adnFrtVCStatsIWFBcOutDiscards Counter
  adnFrtVCStatsIWFBcsOutDiscards Counter
  adnFrtVCStatsIWFBeOutDiscards Counter
  adnFrtVCStatsInCongsState AdnCongestLevels

AdnLapParamEntry  
SEQUENCE    
  adnLapDLCIIndex INTEGER -2147483648..2147483647
  adnLapParamStationType INTEGER
  adnLapParamN201FrameSize INTEGER -2147483648..2147483647
  adnLapParamKWindowSize INTEGER
  adnLapParamN200RxmitCount INTEGER
  adnLapParamT200AckTimer INTEGER -2147483648..2147483647
  adnLapParamT203IdleTimer INTEGER -2147483648..2147483647
  adnLapParamProtocolID INTEGER
  adnLapParamAlarmsEnable INTEGER
  adnLapParamPerfEnable INTEGER

AdnLapFlowEntry  
SEQUENCE    
  adnLapFlowStateChanges Counter
  adnLapFlowChangeReason INTEGER
  adnLapFlowCurrentMode INTEGER
  adnLapFlowBusyDefers Counter
  adnLapFlowRejOutPkts Counter
  adnLapFlowRejInPkts Counter
  adnLapFlowT200Timeouts Counter
  adnLapFlowT203Timeouts Counter
  adnLapFlowLinkResets Counter
  adnLapFlowNsErrorsIns Counter
  adnLapFlowNrErrorsIns Counter
  adnLapFlowFrmrSent OCTET STRING
  adnLapFlowFrmrReceived OCTET STRING

AdnDsx1ConfigEntry  
SEQUENCE    
  adnDsx1LineType INTEGER
  adnDsx1LineLength INTEGER
  adnDsx1LineStatus INTEGER -2147483648..2147483647
  adnDsx1MsAisTest INTEGER
  adnDsx1MsFerfTest INTEGER
  adnDsx1RemLoopbackTest INTEGER
  adnDsx1LineHWStatus INTEGER -2147483648..2147483647
  adnDsx1StatType INTEGER
  adnDsx1LinePerfStatus INTEGER -2147483648..2147483647

AdnDsx1CounterEntry  
SEQUENCE    
  adnDsx1LosCounter Counter
  adnDsx1AisCounter Counter
  adnDsx1FerfCounter Counter
  adnDsx1FeCounter Counter
  adnDsx1LofCounter Counter
  adnDsx1FebeCounter Counter
  adnDsx1PcvCounter Counter
  adnDsx1Ts16AisCounter Counter
  adnDsx1RsaCounter Counter
  adnDsx1LsmaCounter Counter
  adnDsx1LcvCounter Counter
  adnDsx1LcmaCounter Counter
  adnDsx1SefCounter Counter
  adnDsx1ExzCounter Counter

AdnDsx1CurrentEntry  
SEQUENCE    
  adnDsx1CurrentLSESs Gauge
  adnDsx1CurrentLLOSSs Gauge
  adnDsx1CurrentAESs Gauge
  adnDsx1CurrentAISSs Gauge

AdnDsx1IntervalEntry  
SEQUENCE    
  adnDsx1IntervalNumber INTEGER -2147483648..2147483647
  adnDsx1IntervalLSESs Gauge
  adnDsx1IntervalLLOSSs Gauge
  adnDsx1IntervalAESs Gauge
  adnDsx1IntervalAISSs Gauge

AdnDsx1DayIntervalEntry  
SEQUENCE    
  adnDsx1DayIntervalESs Gauge
  adnDsx1DayIntervalSESs Gauge
  adnDsx1DayIntervalSEFSs Gauge
  adnDsx1DayIntervalUASs Gauge
  adnDsx1DayIntervalCSSs Gauge
  adnDsx1DayIntervalPCVs Gauge
  adnDsx1DayIntervalLESs Gauge
  adnDsx1DayIntervalBESs Gauge
  adnDsx1DayIntervalLCVs Gauge
  adnDsx1DayIntervalLSESs Gauge
  adnDsx1DayIntervalLLOSSs Gauge
  adnDsx1DayIntervalAESs Gauge
  adnDsx1DayIntervalAISSs Gauge

AdnDsx1FarEndCurrentEntry  
SEQUENCE    
  adnDsx1FarEndCurrentAESs Gauge

AdnDsx1FarEndIntervalEntry  
SEQUENCE    
  adnDsx1FarEndIntervalNumber INTEGER -2147483648..2147483647
  adnDsx1FarEndIntervalAESs Gauge

AdnDsx1FarEndDayIntervalEntry  
SEQUENCE    
  adnDsx1FarEndDayIntervalESs Gauge
  adnDsx1FarEndDayIntervalSESs Gauge
  adnDsx1FarEndDayIntervalSEFSs Gauge
  adnDsx1FarEndDayIntervalUASs Gauge
  adnDsx1FarEndDayIntervalCSSs Gauge
  adnDsx1FarEndDayIntervalPCVs Gauge
  adnDsx1FarEndDayIntervalLESs Gauge
  adnDsx1FarEndDayIntervalBESs Gauge
  adnDsx1FarEndDayIntervalAESs Gauge

AdnDsx1ItuCurrentEntry  
SEQUENCE    
  adnDsx1ItuCurrentESs Gauge
  adnDsx1ItuCurrentSESs Gauge
  adnDsx1ItuCurrentBBEs Gauge
  adnDsx1ItuFarEndCurrentESs Gauge
  adnDsx1ItuFarEndCurrentSESs Gauge
  adnDsx1ItuFarEndCurrentBBEs Gauge
  adnDsx1ItuCurrentUASs Gauge

AdnDsx1ItuIntervalEntry  
SEQUENCE    
  adnDsx1ItuIntervalNumber INTEGER -2147483648..2147483647
  adnDsx1ItuIntervalESs Gauge
  adnDsx1ItuIntervalSESs Gauge
  adnDsx1ItuIntervalBBEs Gauge
  adnDsx1ItuFarEndIntervalESs Gauge
  adnDsx1ItuFarEndIntervalSESs Gauge
  adnDsx1ItuFarEndIntervalBBEs Gauge
  adnDsx1ItuIntervalUASs Gauge

AdnDsx1ItuDayIntervalEntry  
SEQUENCE    
  adnDsx1ItuDayIntervalESs Gauge
  adnDsx1ItuDayIntervalSESs Gauge
  adnDsx1ItuDayIntervalBBEs Gauge
  adnDsx1ItuFarEndDayIntervalESs Gauge
  adnDsx1ItuFarEndDayIntervalSESs Gauge
  adnDsx1ItuFarEndDayIntervalBBEs Gauge
  adnDsx1ItuDayIntervalUASs Gauge

AdnX3ConfigEntry  
SEQUENCE    
  adnX3MsferfTest INTEGER
  adnX3PathferfTest INTEGER
  adnX3AisTest INTEGER
  adnX3Scramblerconfig INTEGER
  adnX3IdleCellFillingconfig INTEGER
  adnX3LineStatus INTEGER -2147483648..2147483647
  adnX3LinePerfStatus INTEGER -2147483648..2147483647
  adnX3LineHWStatus INTEGER -2147483648..2147483647

AdnX3CounterEntry  
SEQUENCE    
  adnX3LOSCounter Counter
  adnX3AISCounter Counter
  adnX3YellowAlarmCounter Counter
  adnX3PBitCounter Counter
  adnX3CBitCounter Counter
  adnX3CBitFebeCounter Counter
  adnX3LOFCounter Counter
  adnX3LCVCounter Counter
  adnX3FebeCounter Counter
  adnX3PathferfCounter Counter
  adnX3Bip8Counter Counter
  adnX3OOFCounter Counter
  adnX3HECCorrectedCounter Counter
  adnX3HECUncorrectedCounter Counter
  adnX3UpwardsFIFOCounter Counter
  adnX3DownwardsFIFOCounter Counter
  adnX3HBERCounter Counter
  adnX3IdleCodeCounter Counter
  adnX3LOCDCounter Counter
  adnX3ModeChangeCounter Counter
  adnX3PlcpLOFCounter Counter
  adnX3PlcpOOFCounter Counter

AdnX3CurrentEntry  
SEQUENCE    
  adnX3CurrentESs Gauge
  adnX3CurrentSESs Gauge
  adnX3CurrentBBEs Gauge
  adnX3CurrentFarEndESs Gauge
  adnX3CurrentFarEndSESs Gauge
  adnX3CurrentFarEndBBEs Gauge
  adnX3CurrentUASs Gauge

AdnX3IntervalEntry  
SEQUENCE    
  adnX3IntervalNumber INTEGER -2147483648..2147483647
  adnX3IntervalESs Gauge
  adnX3IntervalSESs Gauge
  adnX3IntervalBBEs Gauge
  adnX3IntervalFarEndESs Gauge
  adnX3IntervalFarEndSESs Gauge
  adnX3IntervalFarEndBBEs Gauge
  adnX3IntervalUASs Gauge

AdnX3DayEntry  
SEQUENCE    
  adnX3DayESs Gauge
  adnX3DaySESs Gauge
  adnX3DayBBEs Gauge
  adnX3DayFarEndESs Gauge
  adnX3DayFarEndSESs Gauge
  adnX3DayFarEndBBEs Gauge
  adnX3DayUASs Gauge

AdnX3TotalEntry  
SEQUENCE    
  adnX3TotalESs Gauge
  adnX3TotalSESs Gauge
  adnX3TotalBBEs Gauge
  adnX3TotalFarEndESs Gauge
  adnX3TotalFarEndSESs Gauge
  adnX3TotalFarEndBBEs Gauge
  adnX3TotalUASs Gauge

AdnSonetMediumEntry  
SEQUENCE    
  adnsonetMediumStatus INTEGER -2147483648..2147483647
  adnsonetMediumLaserDegradation Counter
  adnsonetMediumLaserTransmitSignalOut Counter
  adnsonetMediumAppliqueFailure Counter
  adnsonetMediumConfigLineClockMode INTEGER
  adnsonetMediumConfigLaserPower INTEGER

AdnSonetSectionEntry  
SEQUENCE    
  adnsonetSectionStatus INTEGER -2147483648..2147483647
  adnsonetSectionLOS Counter
  adnsonetSectionLOF Counter
  adnsonetSectionOOF Counter

AdnSonetLineEntry  
SEQUENCE    
  adnsonetLineStatus INTEGER -2147483648..2147483647
  adnsonetLineAIS Counter
  adnsonetLineRcvRDI Counter
  adnsonetLineBIP Counter
  adnsonetLineConfigLoopback INTEGER
  adnsonetLineConfigRDI INTEGER
  adnsonetLineConfigAIS INTEGER

AdnSonetPathEntry  
SEQUENCE    
  adnsonetPathWidth INTEGER
  adnsonetPathStatus INTEGER -2147483648..2147483647
  adnsonetPathLOP Counter
  adnsonetPathAIS Counter
  adnsonetPathRcvRDI Counter
  adnsonetPathBIP8 Counter
  adnsonetPathFEBE Counter
  adnsonetPathConfigRDI INTEGER
  adnsonetPathConfigAIS INTEGER

AdnSonetTCEntry  
SEQUENCE    
  adnsonetTCStatus INTEGER -2147483648..2147483647
  adnsonetTCOCD Counter
  adnsonetTCCorrectedHEC Counter
  adnsonetTCUnCorrectedHEC Counter
  adnsonetTCUpBufferOverflow Counter
  adnsonetTCDownBufferOverflow Counter
  adnsonetTCETtoLTLoss Counter
  adnsonetTCConfigCRD INTEGER

AdnSonetCurrentEntry  
SEQUENCE    
  adnsonetCurrentESs Gauge
  adnsonetCurrentSESs Gauge
  adnsonetCurrentBBEs Gauge
  adnsonetCurrentUASs Gauge

AdnSonetIntervalEntry  
SEQUENCE    
  adnsonetIntervalNumber INTEGER -2147483648..2147483647
  adnsonetIntervalESs Gauge
  adnsonetIntervalSESs Gauge
  adnsonetIntervalBBEs Gauge
  adnsonetIntervalUASs Gauge

AdnSonetTotalEntry  
SEQUENCE    
  adnsonetTotalESs Gauge
  adnsonetTotalSESs Gauge
  adnsonetTotalBBEs Gauge
  adnsonetTotalUASs Gauge

AdnSonetDayEntry  
SEQUENCE    
  adnsonetDayESs Gauge
  adnsonetDaySESs Gauge
  adnsonetDayBBEs Gauge
  adnsonetDayUASs Gauge

AdnSonetFarEndCurrentEntry  
SEQUENCE    
  adnsonetFarEndCurrentESs Gauge
  adnsonetFarEndCurrentSESs Gauge
  adnsonetFarEndCurrentBBEs Gauge

AdnSonetFarEndIntervalEntry  
SEQUENCE    
  adnsonetFarEndIntervalNumber INTEGER -2147483648..2147483647
  adnsonetFarEndIntervalESs Gauge
  adnsonetFarEndIntervalSESs Gauge
  adnsonetFarEndIntervalBBEs Gauge

AdnSonetFarEndTotalEntry  
SEQUENCE    
  adnsonetFarEndTotalESs Gauge
  adnsonetFarEndTotalSESs Gauge
  adnsonetFarEndTotalBBEs Gauge

AdnSonetFarEndDayEntry  
SEQUENCE    
  adnsonetFarEndDayESs Gauge
  adnsonetFarEndDaySESs Gauge
  adnsonetFarEndDayBBEs Gauge

AdnSonetMaintenanceEntry  
SEQUENCE    
  adnsonetLineHWStatus INTEGER -2147483648..2147483647
  adnsonetLinePerfStatus INTEGER -2147483648..2147483647

AdnAtmAdminStatus  
INTEGER up(1), down(2)    

AdnAtmAllocOrder  
INTEGER increasing(1), decreasing(2), notSignificant(3)    

AdnAtmCniOperStatus  
INTEGER fast(1), slow(2), rxcall(3), callup(4)    

AdnAtmCniSourceDest  
INTEGER source(1), destination(2)    

AdnAtmDirectedPath  
AdnEnableDisabled    

AdnAtmDirRoutFlag  
INTEGER other(1), preferred(2), exclusive(3)    

AdnAtmNumPlan  
INTEGER private(1), nsapE164(2), nativeE164(3), other(4), notSignificant(5)    

AdnAtmOperStatus  
INTEGER up(1), down(2)    

AdnAtmSigPIUpdate  
INTEGER other(1), permanentAllowed(2), permanentRestricted(3), perCallAllowed(4), perCallRestricted(5), disabled(6)    

AdnAtmSigScreening  
INTEGER other(1), transparent(2), none(3), alwaysAccept(4), acceptAndCorrect(5), refuse(6)    

AdnAtmUniOperStatus  
INTEGER fast(1), slow(2), rxcall(3), callup(4)    

AdnAtmUniSourceDest  
INTEGER source(1), destination(2)    

AdnAtmVlAISStatus  
INTEGER aisOn(1), aisOff(2), notSignificant(3)    

AdnAtmVlPolicing  
INTEGER notPoliced(1), policeNoSpacing(2), policed(3), supervision(4), useInterfaceValue(5)    

AdnAtmVlTrfDescrType  
INTEGER pcrCdv(1), pcrCdvScrMbs(2), pcrCdvPcr0(3), pcrCdvScr0Mbs0(4)    

AdnAtmVlTrfCapability  
INTEGER ubr(1), cbrRtAggregate(2), vbrNrtAggregate(3), cbrNrtAggregate(4), vbrRtAggregate(5), cbrRtClpZero(6), vbrRtClpZero(7), vbrNrtClpZero(8)    

AdnAtmVlType  
INTEGER pvc(1), svc(2), internalVc(3)    

AdnAtmLogLineEntry  
SEQUENCE    
  adnAtmLogLineVuniIfIndex InterfaceIndex
  adnAtmLogLineVuniVpi INTEGER

AdnAtmInterfaceConfEntry  
SEQUENCE    
  adnAtmInterfaceLowLayerIfIndex InterfaceIndex
  adnAtmInterfaceType INTEGER
  adnAtmInterfaceMaxFillingRate INTEGER
  adnAtmInterfaceBWThreshold1 INTEGER
  adnAtmInterfaceBWThreshold2 INTEGER
  adnAtmInterfaceBWThreshold3 INTEGER
  adnAtmInterfaceMaxPtpVcs INTEGER
  adnAtmInterfaceMaxPtMCc INTEGER
  adnAtmInterfaceMaxPvcc INTEGER
  adnAtmInterfaceMaxSvcc INTEGER
  adnAtmInterfaceVccLowVpi INTEGER
  adnAtmInterfaceVccHighVpi INTEGER
  adnAtmInterfaceMaxPVpcs INTEGER
  adnAtmInterfacePvpcLowVpi INTEGER
  adnAtmInterfacePvpcHighVpi INTEGER
  adnAtmInterfaceMaxSVpcs INTEGER
  adnAtmInterfaceSvpcAllocOrd AdnAtmAllocOrder
  adnAtmInterfaceSvpcLowVpi INTEGER
  adnAtmInterfaceSvpcHighVpi INTEGER
  adnAtmInterfaceMaxActiveVpVpiBits INTEGER
  adnAtmInterfaceMaxActiveVcVpiBits INTEGER
  adnAtmInterfaceCharging AdnEnableDisabled
  adnAtmInterfaceStatistics AdnEnableDisabled
  adnAtmInterfaceTraps AdnEnableDisabled
  adnAtmInterfaceUserNetFlg INTEGER
  adnAtmInterfaceSigType INTEGER
  adnAtmInterfaceRemRoutingNodeID AdnRoutingID
  adnAtmInterfaceRemIfIndex InterfaceIndex
  adnAtmInterfaceCniBlockingStatus INTEGER
  adnAtmInterfaceMaxVcs INTEGER
  adnAtmInterfaceMaxPtmRootVcs INTEGER
  adnAtmInterfaceMaxPtmLeafVcs INTEGER
  adnAtmInterfaceMaxVpiForVccs INTEGER
  adnAtmInterfaceCacAlgorithm AdnEnableDisabled
  adnAtmInterfaceK INTEGER
  adnAtmInterfaceKUbr INTEGER
  adnAtmInterfaceUbr1Tagging AdnEnableDisabled
  adnAtmInterfacePolicing INTEGER
  adnAtmInterfaceMonetaryCost INTEGER
  adnAtmInterfaceTransitDelay INTEGER
  adnAtmInterfaceMaxTDSensitive INTEGER
  adnAtmInterfaceMaxTDOther INTEGER
  adnAtmInterfaceChargingBehaviour INTEGER
  adnAtmInterfaceAddrRegistration AdnEnableDisabled
  adnAtmInterfaceSvcCdvTol INTEGER
  adnAtmInterfaceVpiForVccAllocOrd AdnAtmAllocOrder
  adnAtmInterfaceRemNodeMacNum INTEGER -2147483648..2147483647
  adnAtmInterfaceRemNodeAreaNum INTEGER -2147483648..2147483647
  adnAtmInterfaceAllowedAtc INTEGER

AdnAtmVpiVccConfEntry  
SEQUENCE    
  adnAtmVpiVccIndex INTEGER
  adnAtmVpiVccTrmBandwidth INTEGER
  adnAtmVpiVccRcvBandwidth INTEGER
  adnAtmVpiVccMaxFillingRate INTEGER
  adnAtmVpiVccMaxVcc INTEGER
  adnAtmVpiVccMaxPVccs INTEGER
  adnAtmVpiVccPvccLowVci INTEGER
  adnAtmVpiVccPvccHighVci INTEGER
  adnAtmVpiVccMaxSVccs INTEGER
  adnAtmVpiVccSvccAllocOrd AdnAtmAllocOrder
  adnAtmVpiVccSvccLowVci INTEGER
  adnAtmVpiVccSvccHighVci INTEGER

AdnAtmSaalEntry  
SEQUENCE    
  adnAtmSaalVpi INTEGER
  adnAtmSaalVci INTEGER
  adnAtmSaalConnectType INTEGER
  adnAtmSaalBandwidth INTEGER
  adnAtmSaalMaxCC INTEGER
  adnAtmSaalMaxPD INTEGER
  adnAtmSaalMaxSTAT INTEGER
  adnAtmSaalCCTimer INTEGER
  adnAtmSaalNoRespTimer INTEGER
  adnAtmSaalPollTimer INTEGER
  adnAtmSaalKeepAliveTimer INTEGER
  adnAtmSaalIdleTimer INTEGER
  adnAtmSaalMaxLength INTEGER
  adnAtmSaalAdminStatus AdnAtmAdminStatus
  adnAtmSaalOperStatus AdnAtmOperStatus

AdnAtmSigEntry  
SEQUENCE    
  adnAtmSigVpi INTEGER
  adnAtmSigVci INTEGER
  adnAtmSigProtocol INTEGER
  adnAtmSigT301 INTEGER
  adnAtmSigT302 INTEGER
  adnAtmSigT303 INTEGER
  adnAtmSigT304 INTEGER
  adnAtmSigT306 INTEGER
  adnAtmSigT308 INTEGER
  adnAtmSigT309 INTEGER
  adnAtmSigT310 INTEGER
  adnAtmSigT313 INTEGER
  adnAtmSigT316 INTEGER
  adnAtmSigT317 INTEGER
  adnAtmSigT322 INTEGER
  adnAtmSigT398 INTEGER
  adnAtmSigT399 INTEGER
  adnAtmSigT331 INTEGER
  adnAtmSigT397 INTEGER
  adnAtmSigUserNetFlag INTEGER
  adnAtmSigCallProc AdnEnableDisabled
  adnAtmSigBrSendComp AdnEnableDisabled
  adnAtmSigSetupScreening INTEGER
  adnAtmSigDdi AdnEnableDisabled
  adnAtmSigMsn AdnEnableDisabled
  adnAtmSigSvccReconnect AdnEnableDisabled
  adnAtmSigCallBarring INTEGER
  adnAtmSigClip INTEGER
  adnAtmSigClir AdnAtmSigPIUpdate
  adnAtmSigColp INTEGER
  adnAtmSigColr AdnAtmSigPIUpdate
  adnAtmSigSub AdnEnableDisabled
  adnAtmSigUus AdnEnableDisabled
  adnAtmSigVpiVciAlloc AdnEnableDisabled
  adnAtmSigCniCheckingState INTEGER
  adnAtmSigSetupAddr INTEGER
  adnAtmSigConnectScreening INTEGER

AdnAtmVplEntry  
SEQUENCE    
  adnAtmVplTopology INTEGER
  adnAtmVplTrafficType INTEGER
  adnAtmVplType AdnAtmVlType
  adnAtmVplTransferCapability AdnAtmVlTrfCapability
  adnAtmVplTrafficDescrType INTEGER
  adnAtmVplTrmPcrAggregate INTEGER
  adnAtmVplTrmPcrClpZero INTEGER
  adnAtmVplTrmScrAggregate INTEGER
  adnAtmVplTrmScrClpZero INTEGER
  adnAtmVplTrmMbsAggregate INTEGER
  adnAtmVplTrmMbsClpZero INTEGER
  adnAtmVplTrmCdvTol INTEGER
  adnAtmVplTrmBwWeighting INTEGER
  adnAtmVplRcvPcrAggregate INTEGER
  adnAtmVplRcvPcrClpZero INTEGER
  adnAtmVplRcvScrAggregate INTEGER
  adnAtmVplRcvScrClpZero INTEGER
  adnAtmVplRcvMbsAggregate INTEGER
  adnAtmVplRcvMbsClpZero INTEGER
  adnAtmVplRcvCdvTol INTEGER
  adnAtmVplRcvBwWeighting INTEGER
  adnAtmVplPolicing AdnAtmVlPolicing
  adnAtmVplPriority INTEGER
  adnAtmVplModeType INTEGER
  adnAtmVplTrmAISStatus AdnAtmVlAISStatus
  adnAtmVplTrmTrafficDescrType AdnAtmVlTrfDescrType
  adnAtmVplTrmTagging AdnEnableDisabled
  adnAtmVplTrmPacketDiscard AdnEnableDisabled
  adnAtmVplRcvAISStatus AdnAtmVlAISStatus
  adnAtmVplRcvTrafficDescrType AdnAtmVlTrfDescrType
  adnAtmVplRcvTagging AdnEnableDisabled
  adnAtmVplRcvPacketDiscard AdnEnableDisabled
  adnAtmVplInternodeType INTEGER

AdnAtmVclEntry  
SEQUENCE    
  adnAtmVclTopology INTEGER
  adnAtmVclTrafficType INTEGER
  adnAtmVclType AdnAtmVlType
  adnAtmVclTransferCapability AdnAtmVlTrfCapability
  adnAtmVclTrafficDescrType INTEGER
  adnAtmVclTrmPcrAggregate INTEGER
  adnAtmVclTrmPcrClpZero INTEGER
  adnAtmVclTrmScrAggregate INTEGER
  adnAtmVclTrmScrClpZero INTEGER
  adnAtmVclTrmMbsAggregate INTEGER
  adnAtmVclTrmMbsClpZero INTEGER
  adnAtmVclTrmCdvTol INTEGER
  adnAtmVclTrmBwWeighting INTEGER
  adnAtmVclRcvPcrAggregate INTEGER
  adnAtmVclRcvPcrClpZero INTEGER
  adnAtmVclRcvScrAggregate INTEGER
  adnAtmVclRcvScrClpZero INTEGER
  adnAtmVclRcvMbsAggregate INTEGER
  adnAtmVclRcvMbsClpZero INTEGER
  adnAtmVclRcvCdvTol INTEGER
  adnAtmVclRcvBwWeighting INTEGER
  adnAtmVclPolicing AdnAtmVlPolicing
  adnAtmVclPriority INTEGER
  adnAtmVclModeType INTEGER
  adnAtmVclTrmAISStatus AdnAtmVlAISStatus
  adnAtmVclTrmTrafficDescrType AdnAtmVlTrfDescrType
  adnAtmVclTrmTagging AdnEnableDisabled
  adnAtmVclTrmPacketDiscard AdnEnableDisabled
  adnAtmVclRcvAISStatus AdnAtmVlAISStatus
  adnAtmVclRcvTrafficDescrType AdnAtmVlTrfDescrType
  adnAtmVclRcvTagging AdnEnableDisabled
  adnAtmVclRcvPacketDiscard AdnEnableDisabled
  adnAtmVclLogLineType INTEGER

AdnAtmUniVpCconnectEntry  
SEQUENCE    
  adnAtmUniVpCconnectIndex INTEGER
  adnAtmUniVpCconnectOutIfIndex InterfaceIndex
  adnAtmUniVpCconnectOutVpi INTEGER
  adnAtmUniVpCconnectOutCcnIndex INTEGER
  adnAtmUniVpCconnectAdminStatus AdnAtmAdminStatus
  adnAtmUniVpCconnectOperStatus AdnAtmUniOperStatus
  adnAtmUniVpCconnectSourceDest AdnAtmUniSourceDest
  adnAtmUniVpCconnectStatistics INTEGER
  adnAtmUniVpCconnectDirectedPath AdnAtmDirectedPath
  adnAtmUniVpCconnectRetryAttempts INTEGER
  adnAtmUniVpCconnectFastRetry INTEGER
  adnAtmUniVpCconnectSlowRetry INTEGER
  adnAtmUniVpCconnectRemNumPlan AdnAtmNumPlan
  adnAtmUniVpCconnectRemPhysAddress PhysAddress
  adnAtmUniVpCconnectRemVpi INTEGER
  adnAtmUniVpCconnectRemCcnIndex INTEGER
  adnAtmUniVpCconnectRemRoutingNodeId AdnRoutingID
  adnAtmUniVpCconnectCumulNodes INTEGER
  adnAtmUniVpCconnectMaxTransitDelay INTEGER
  adnAtmUniVpCconnectCharging INTEGER
  adnAtmUniVpCconnectCumulTD INTEGER
  adnAtmUniVpCconnectCumulMonetaryCst INTEGER
  adnAtmUniVpCconnectCauseError INTEGER
  adnAtmUniVpCconnectLastCanpCause INTEGER
  adnAtmUniVpCconnectLastErrorNodeID AdnRoutingID
  adnAtmUniVpCconnectLastLocation INTEGER
  adnAtmUniVpCconnectLastCause INTEGER
  adnAtmUniVpCconnectLastDiag INTEGER
  adnAtmUniVpCconnectRemNodeMacNum INTEGER -2147483648..2147483647
  adnAtmUniVpCconnectRemNodeAreaNum INTEGER -2147483648..2147483647
  adnAtmUniVpCconnectErrorNodeMacNum INTEGER -2147483648..2147483647
  adnAtmUniVpCconnectErrorNodeAreaNum INTEGER -2147483648..2147483647
  adnAtmUniVpCconnectLastChassis INTEGER -2147483648..2147483647
  adnAtmUniVpCconnectLastSlot INTEGER -2147483648..2147483647
  adnAtmUniVpCconnectMaxHops INTEGER
  adnAtmUniVpCconnectPvcDescr DisplayString

AdnAtmCniVpCconnectEntry  
SEQUENCE    
  adnAtmCniVpCconnectIndex INTEGER
  adnAtmCniVpCconnectOutIfIndex InterfaceIndex
  adnAtmCniVpCconnectOutVpi INTEGER
  adnAtmCniVpCconnectOutCcnIndex INTEGER
  adnAtmCniVpCconnectAdminStatus AdnAtmAdminStatus
  adnAtmCniVpCconnectOperStatus AdnAtmCniOperStatus
  adnAtmCniVpCconnectSourceDest AdnAtmCniSourceDest
  adnAtmCniVpCconnectStatistics INTEGER
  adnAtmCniVpCconnectDirectedPath AdnAtmDirectedPath

AdnAtmUniVcCconnectEntry  
SEQUENCE    
  adnAtmUniVcCconnectIndex INTEGER
  adnAtmUniVcCconnectOutIfIndex InterfaceIndex
  adnAtmUniVcCconnectOutVpi INTEGER
  adnAtmUniVcCconnectOutVci INTEGER
  adnAtmUniVcCconnectOutCcnIndex INTEGER
  adnAtmUniVcCconnectAdminStatus AdnAtmAdminStatus
  adnAtmUniVcCconnectOperStatus AdnAtmUniOperStatus
  adnAtmUniVcCconnectSourceDest AdnAtmUniSourceDest
  adnAtmUniVcCconnectStatistics INTEGER
  adnAtmUniVcCconnectDirectedPath AdnAtmDirectedPath
  adnAtmUniVcCconnectRetryAttempts Counter
  adnAtmUniVcCconnectFastRetry INTEGER -2147483648..2147483647
  adnAtmUniVcCconnectSlowRetry INTEGER -2147483648..2147483647
  adnAtmUniVcCconnectRemNumPlan AdnAtmNumPlan
  adnAtmUniVcCconnectRemPhysAddress PhysAddress
  adnAtmUniVcCconnectRemVpi INTEGER
  adnAtmUniVcCconnectRemVci INTEGER
  adnAtmUniVcCconnectRemCcnIndex INTEGER
  adnAtmUniVcCconnectRemRoutingNodeId AdnRoutingID
  adnAtmUniVcCconnectCumulNodes INTEGER
  adnAtmUniVcCconnectMaxTransitDelay INTEGER
  adnAtmUniVcCconnectCharging INTEGER
  adnAtmUniVcCconnectCumulTD INTEGER
  adnAtmUniVcCconnectCumulMonetaryCst INTEGER
  adnAtmUniVcCconnectCauseError INTEGER
  adnAtmUniVcCconnectLastCanpCause INTEGER
  adnAtmUniVcCconnectLastErrorNodeID AdnRoutingID
  adnAtmUniVcCconnectLastLocation INTEGER
  adnAtmUniVcCconnectLastCause INTEGER
  adnAtmUniVcCconnectLastDiag INTEGER
  adnAtmUniVcCconnectRemNodeMacNum INTEGER -2147483648..2147483647
  adnAtmUniVcCconnectRemNodeAreaNum INTEGER -2147483648..2147483647
  adnAtmUniVcCconnectErrorNodeMacNum INTEGER -2147483648..2147483647
  adnAtmUniVcCconnectErrorNodeAreaNum INTEGER -2147483648..2147483647
  adnAtmUniVcCconnectLastChassis INTEGER -2147483648..2147483647
  adnAtmUniVcCconnectLastSlot INTEGER -2147483648..2147483647
  adnAtmUniVcCconnectPvcDescr DisplayString

AdnAtmCniVcCconnectEntry  
SEQUENCE    
  adnAtmCniVcCconnectIndex INTEGER
  adnAtmCniVcCconnectOutIfIndex InterfaceIndex
  adnAtmCniVcCconnectOutVpi INTEGER
  adnAtmCniVcCconnectOutVci INTEGER
  adnAtmCniVcCconnectOutCcnIndex INTEGER
  adnAtmCniVcCconnectAdminStatus AdnAtmAdminStatus
  adnAtmCniVcCconnectOperStatus AdnAtmCniOperStatus
  adnAtmCniVcCconnectSourceDest AdnAtmCniSourceDest
  adnAtmCniVcCconnectStatistics INTEGER
  adnAtmCniVcCconnectDirectedPath AdnAtmDirectedPath

AdnAtmVpcDirRoutEntry  
SEQUENCE    
  adnAtmVpcDirRoutIndex INTEGER
  adnAtmVpcDirRoutNodeId AdnRoutingID
  adnAtmVpcDirRoutOutChassis INTEGER
  adnAtmVpcDirRoutOutSlot INTEGER
  adnAtmVpcDirRoutOutLine INTEGER -2147483648..2147483647
  adnAtmVpcDirRoutFlag AdnAtmDirRoutFlag
  adnAtmVpcDirRoutNodeMacNum INTEGER -2147483648..2147483647
  adnAtmVpcDirRoutNodeAreaNum INTEGER -2147483648..2147483647

AdnAtmVccDirRoutEntry  
SEQUENCE    
  adnAtmVccDirRoutIndex INTEGER
  adnAtmVccDirRoutNodeId AdnRoutingID
  adnAtmVccDirRoutOutChassis INTEGER
  adnAtmVccDirRoutOutSlot INTEGER
  adnAtmVccDirRoutOutLine INTEGER -2147483648..2147483647
  adnAtmVccDirRoutFlag AdnAtmDirRoutFlag
  adnAtmVccDirRoutNodeMacNum INTEGER -2147483648..2147483647
  adnAtmVccDirRoutNodeAreaNum INTEGER -2147483648..2147483647

AdnAtmReachAddrEntry  
SEQUENCE    
  adnAtmReachAddrIndex INTEGER
  adnAtmReachAddrNumPlan AdnAtmNumPlan
  adnAtmReachAddrNumberLength INTEGER
  adnAtmReachAddrNumber PhysAddress
  adnAtmReachAddrAssocIndex INTEGER

AdnAtmReachAssocAddrEntry  
SEQUENCE    
  adnAtmReachAssocAddrIndex INTEGER
  adnAtmReachAssocAddrNumIndex INTEGER
  adnAtmReachAssocAddrNumPlan AdnAtmNumPlan
  adnAtmReachAssocAddrAddress PhysAddress

AdnAtmInterfacePerfEntry  
SEQUENCE    
  adnAtmInterfacePerfTrmAllocBwVpiForVcc Counter
  adnAtmInterfacePerfRcvAllocBwVpiForVcc Counter
  adnAtmInterfacePerfTrmAllocBwVpcs Counter
  adnAtmInterfacePerfRcvAllocBwVpcs Counter
  adnAtmInterfacePerfTrmAllocBwVccs Counter
  adnAtmInterfacePerfRcvAllocBwVccs Counter
  adnAtmInterfacePerfPPtpVpcs Counter
  adnAtmInterfacePerfSPtpVpcs Counter
  adnAtmInterfacePerfPPtmRootVpcs Counter
  adnAtmInterfacePerfSPtmRootVpcs Counter
  adnAtmInterfacePerfPPtmLeafVpcs Counter
  adnAtmInterfacePerfSPtmLeafVpcs Counter

AdnAtmVpiVccPerfEntry  
SEQUENCE    
  adnAtmVpiVccPerfTrmAllocBwVccs Counter
  adnAtmVpiVccPerfRcvAllocBwVccs Counter
  adnAtmVpiVccPerfPPtpVccs Counter
  adnAtmVpiVccPerfSPtpVccs Counter
  adnAtmVpiVccPerfPPtmRootVccs Counter
  adnAtmVpiVccPerfSPtmRootVccs Counter
  adnAtmVpiVccPerfPPtmLeafVccs Counter
  adnAtmVpiVccPerfSPtmLeafVccs Counter

AdnAtmVplPerfEntry  
SEQUENCE    
  adnAtmVplPerfRcvCellForwarded Counter
  adnAtmVplPerfRcvCellDiscarded Counter
  adnAtmVplPerfRcvCellVsaANonConform Counter
  adnAtmVplPerfRcvCellVsaBNonConform Counter
  adnAtmVplPerfRcvCellTagged Counter

AdnAtmVclPerfEntry  
SEQUENCE    
  adnAtmVclPerfRcvCellForwarded Counter
  adnAtmVclPerfRcvCellDiscarded Counter
  adnAtmVclPerfRcvCellVsaANonConform Counter
  adnAtmVclPerfRcvCellVsaBNonConform Counter
  adnAtmVclPerfRcvCellTagged Counter

AdnAtmAal5PerfEntry  
SEQUENCE    
  adnAtmAal5PerfLengthErrors Counter
  adnAtmAal5PerfCpiErrors Counter

AdnFRAIWConfEntry  
SEQUENCE    
  adnFRAIWConfIUNIifIndex InterfaceIndex
  adnFRAIWConfVpi INTEGER
  adnFRAIWConfVci INTEGER
  adnFRAIWConfLogLineType INTEGER
  adnFRAIWConfAalType INTEGER
  adnFRAIWConfInitCLP INTEGER
  adnFRAIWConfTrapEnable AdnEnableDisabled
  adnFRAIWConfStatisticsEnable AdnEnableDisabled
  adnFRAIWConfSegmPcr INTEGER
  adnFRAIWConfSegmScr INTEGER
  adnFRAIWConfSegmMbs INTEGER
  adnFRAIWConfCosRtOutOctets Counter
  adnFRAIWConfCosRtOutPkts Counter
  adnFRAIWConfCosRtOutErrors Counter
  adnFRAIWConfCosNrtOutOctets Counter
  adnFRAIWConfCosNrtOutPkts Counter
  adnFRAIWConfCosNrtOutErrors Counter

AdnFrAtmSerIWEntry  
SEQUENCE    
  adnFrAtmSerIWInitEFCI INTEGER
  adnFrAtmSerIWInitDE INTEGER
  adnFrAtmSerIWEncapsMode INTEGER
  adnFrAtmSerIWAddrDLCI INTEGER
  adnFrAtmSerIWUserN391 INTEGER
  adnFrAtmSerIWUserN392 INTEGER
  adnFrAtmSerIWUserN393 INTEGER
  adnFrAtmSerIWUserT391 INTEGER
  adnFrAtmSerIWNetN392 INTEGER
  adnFrAtmSerIWNetN393 INTEGER
  adnFrAtmSerIWNetT392 INTEGER

AdnAtmTCEntry  
SEQUENCE    
  adnAtmTCAlarmState INTEGER -2147483648..2147483647
  adnAtmTCScramblerConfig INTEGER
  adnAtmTCCellRateDecConfig INTEGER
  adnAtmTCMappingConfig INTEGER
  adnAtmTCLossOfCellDelCounter Counter
  adnAtmTCCorrectedHecCounter Counter
  adnAtmTCUncorrectedHecCounter Counter
  adnAtmTCUpwardOverflowCounter Counter
  adnAtmTCDownwardOverflowCounter Counter
  adnAtmTCLossOfAtmSignalCounter Counter

AdnAtmDs3PlcpEntry  
SEQUENCE    
  adnAtmDs3PlcpFerfCounter Counter
  adnAtmDs3PlcpLofCounter Counter
  adnAtmDs3PlcpFebeCounter Counter
  adnAtmDs3PlcpBip8Counter Counter
  adnAtmDs3PlcpOofCounter Counter

AdnAtmBoardErCounterEntry  
SEQUENCE    
  adnAtmBoardErOrWgStatus INTEGER -2147483648..2147483647
  adnAtmBoardASEStatus INTEGER -2147483648..2147483647
  adnAtmBoardCIGStatus INTEGER -2147483648..2147483647
  adnAtmBoardHSCStatus INTEGER -2147483648..2147483647
  adnAtmBoardErQRP0RAMPCounter Counter
  adnAtmBoardErQRP0FIFOCounter Counter
  adnAtmBoardErQRP1RAMPCounter Counter
  adnAtmBoardErQRP1FIFOCounter Counter
  adnAtmBoardErQRP2RAMPCounter Counter
  adnAtmBoardErQRP2FIFOCounter Counter
  adnAtmBoardErQRP3RAMPCounter Counter
  adnAtmBoardErQRP3FIFOCounter Counter
  adnAtmBoardErHMPLLPCCounter Counter
  adnAtmBoardErHMPLHPCCounter Counter
  adnAtmBoardErHMP0SYNCCounter Counter
  adnAtmBoardErHMP1SYNCCounter Counter
  adnAtmBoardErUFOFCounter Counter
  adnAtmBoardErUFRFCounter Counter
  adnAtmBoardErNFOFCounter Counter
  adnAtmBoardErPHTRAMPCounter Counter
  adnAtmBoardErNFRFCounter Counter
  adnAtmBoardErNAVCCounter Counter
  adnAtmBoardErNAVPCounter Counter
  adnAtmBoardErRBOFCounter Counter
  adnAtmBoardErAPPLIQCounter Counter
  adnAtmBoardErLIRC0Counter Counter
  adnAtmBoardErLIRC1Counter Counter
  adnAtmBoardErRFIFOCounter Counter
  adnAtmBoardErRFIFCCounter Counter
  adnAtmBoardErBGETBCounter Counter
  adnAtmBoardErBGMUXCounter Counter
  adnAtmBoardErHOBCounter Counter
  adnAtmBoardErMOBCounter Counter
  adnAtmBoardErLOBCounter Counter
  adnAtmBoardErDRAMPCounter Counter
  adnAtmBoardErRFIFFCounter Counter
  adnAtmBoardCEMStatus INTEGER -2147483648..2147483647
  adnAtmBoardErDCSECounter Counter
  adnAtmBoardErDRFOVCounter Counter
  adnAtmBoardErDCMOVCounter Counter
  adnAtmBoardErDCMMECounter Counter
  adnAtmBoardErUCSECounter Counter
  adnAtmBoardErURFOVCounter Counter
  adnAtmBoardErUCMOVCounter Counter
  adnAtmBoardErUCMMECounter Counter
  adnAtmBoardErRFORRF0Counter Counter
  adnAtmBoardErRFORRF1Counter Counter
  adnAtmBoardErRFORRF2Counter Counter

AdnAtmBoardTraCounterEntry  
SEQUENCE    
  adnAtmBoardTraHMP0ObsCounter Counter
  adnAtmBoardTraHMP1ObsCounter Counter
  adnAtmBoardTraFPTMICICounter Gauge
  adnAtmBoardTraMOBSCDCounter Counter
  adnAtmBoardTraLOBSCDCounter Counter
  adnAtmBoardTraMOBEFCICounter Counter
  adnAtmBoardTraLOBEFCICounter Counter
  adnAtmBoardTraMOBTPDCounter Counter
  adnAtmBoardTraLOBTPDCounter Counter
  adnAtmBoardTraHOBObsCounter Counter
  adnAtmBoardTraMOBObsCounter Counter
  adnAtmBoardTraLOBObsCounter Counter

AdnAeiPortErCounterEntry  
SEQUENCE    
  adnAeiPortErOrWgStatus INTEGER
  adnAeiPortASEStatus INTEGER
  adnAeiPortCIGStatus INTEGER
  adnAeiPortHSCStatus INTEGER
  adnAeiPortErOOSCounter Counter
  adnAeiPortErNFOFCounter Counter
  adnAeiPortErCECHCounter Counter
  adnAeiPortErUCECHCounter Counter
  adnAeiPortErNPECounter Counter
  adnAeiPortErNMA1Counter Counter
  adnAeiPortErEMA1Counter Counter
  adnAeiPortErNICICounter Counter
  adnAeiPortErNCRCCounter Counter
  adnAeiPortErNAALCounter Counter
  adnAeiPortErLOSCounter Counter
  adnAeiPortErRTAGCounter Counter
  adnAeiPortErURCCounter Counter
  adnAeiPortErIEMRAMPCounter Counter
  adnAeiPortErCRCMA1Counter Counter
  adnAeiPortErCRCSICCounter Counter
  adnAeiPortErNSFOFCounter Counter
  adnAeiPortErNFWFCounter Counter
  adnAeiPortErSFWFCounter Counter
  adnAeiPortErNSFRFCounter Counter
  adnAeiPortErUSFRFCounter Counter
  adnAeiPortErUFWFCounter Counter
  adnAeiPortErUSFOFCounter Counter
  adnAeiPortErUCRCCounter Counter
  adnAeiPortErUAALCounter Counter
  adnAeiPortErSFIFOCounter Counter
  adnAeiPortCEMStatus INTEGER

AdnAeiPortTraCounterEntry  
SEQUENCE    
  adnAeiPortTraPTPSetRqCounter Counter
  adnAeiPortTraPTMSetRqCounter Counter
  adnAeiPortTraPTPSetRjBCounter Counter
  adnAeiPortTraPTMSetRjBCounter Counter
  adnAeiPortTraPTPSetRjCCounter Counter
  adnAeiPortTraPTMSetRjCCounter Counter
  adnAeiPortTraPTPSetTrCounter Counter
  adnAeiPortTraPTMSetTrCounter Counter
  adnAeiPortTraPTPCnxCounter Gauge
  adnAeiPortTraPTMCnxCounter Gauge
  adnAeiPortTraEFCCCounter Counter
  adnAeiPortTraPTPBWICIRqCounter Counter
  adnAeiPortTraPTMBWICIRqCounter Counter
  adnAeiPortTraPTPBWRjCounter Counter
  adnAeiPortTraPTMBWRjCounter Counter
  adnAeiPortTraPTPICIRjCounter Counter
  adnAeiPortTraPTMICIRjCounter Counter
  adnAeiPortTraPeakBWCounter Gauge
  adnAeiPortTraFPTPICICounter Gauge
  adnAeiPortTraMPriorBWCounter Gauge
  adnAeiPortTraInCellsCounter Counter
  adnAeiPortTraOutCellsCounter Counter
  adnAeiPortTraEBCCCounter Counter

AdnHscBoardTrMgtEntry  
SEQUENCE    
  adnHscBoardTrMgtOBLineAssig INTEGER
  adnHscBoardTrMgtHOBSize INTEGER
  adnHscBoardTrMgtMOBSize INTEGER
  adnHscBoardTrMgtLOBSize INTEGER
  adnHscBoardTrMgtHOBSCDTh INTEGER
  adnHscBoardTrMgtMOBSCDTh INTEGER
  adnHscBoardTrMgtLOBSCDTh INTEGER
  adnHscBoardTrMgtHOBEFCIOnTh INTEGER
  adnHscBoardTrMgtMOBEFCIOnTh INTEGER
  adnHscBoardTrMgtLOBEFCIOnTh INTEGER
  adnHscBoardTrMgtHOBEFCIOffTh INTEGER
  adnHscBoardTrMgtMOBEFCIOffTh INTEGER
  adnHscBoardTrMgtLOBEFCIOffTh INTEGER
  adnHscBoardTrMgtHOBObsTh INTEGER
  adnHscBoardTrMgtMOBObsTh INTEGER
  adnHscBoardTrMgtLOBObsTh INTEGER
  adnHscBoardTrMgtOBStatus INTEGER -2147483648..2147483647
  adnHscBoardTrMgtHOBCounter Counter
  adnHscBoardTrMgtMOBCounter Counter
  adnHscBoardTrMgtLOBCounter Counter
  adnHscBoardTrMgtMOBSCDCounter Counter
  adnHscBoardTrMgtLOBSCDCounter Counter
  adnHscBoardTrMgtMOBEFCICounter Counter
  adnHscBoardTrMgtLOBEFCICounter Counter
  adnHscBoardTrMgtMOBTPDCounter Counter
  adnHscBoardTrMgtLOBTPDCounter Counter
  adnHscBoardTrMgtHOBObsCounter Counter
  adnHscBoardTrMgtMOBObsCounter Counter
  adnHscBoardTrMgtLOBObsCounter Counter

AdnCESConfEntry  
SEQUENCE    
  adnCESClockMode INTEGER
  adnCESTrunkCondData INTEGER
  adnCESCondSignal INTEGER
  adnCESUpDownTrapEnable INTEGER

AdnRs232InSigEntry  
SEQUENCE    
  adnRs232InSigPortIndex InterfaceIndex
  adnRs232InSigName INTEGER
  adnRs232InSigState INTEGER
  adnRs232InSigChanges Counter
  adnRs232InSigDuration Counter

AdnRs232OutSigEntry  
SEQUENCE    
  adnRs232OutSigPortIndex InterfaceIndex
  adnRs232OutSigName INTEGER
  adnRs232OutSigState INTEGER
  adnRs232OutSigChanges Counter

AdnRs232PortEntry  
SEQUENCE    
  adnRs232PortIndex InterfaceIndex
  adnRs232PortDuration Counter

AdnIfAssocEntry  
SEQUENCE    
  adnFirstIfIndex INTEGER
  adnFirstNodeIndex INTEGER
  adnAssocIfIndex INTEGER
  adnAssocNodeIndex INTEGER
  adnProtocolType INTEGER

AdnAtmCharEntry  
SEQUENCE    
  adnAtmAccEquipType INTEGER
  adnAtmAccTicketVersion INTEGER
  adnAtmAccLocalNodeId INTEGER
  adnAtmAccLocalChassis INTEGER
  adnAtmAccLocalSlot INTEGER
  adnAtmAccLocalLine INTEGER
  adnAtmAccRemoteNodeId INTEGER
  adnAtmAccRemoteChassis INTEGER
  adnAtmAccRemoteSlot INTEGER
  adnAtmAccRemoteLine INTEGER
  adnAtmAccCallTerm INTEGER
  adnAtmAccInterfaceType INTEGER
  adnAtmAccConnectionType INTEGER
  adnAtmAccConnectionTopology INTEGER
  adnAtmAccSourceDest INTEGER
  adnAtmAccCallingPartyNumPlan INTEGER
  adnAtmAccCallingPartyLength INTEGER
  adnAtmAccCallingPartyNumber OCTET STRING
  adnAtmAccCalledPartyNumPlan INTEGER
  adnAtmAccCalledPartyLength INTEGER
  adnAtmAccCalledPartyNumber OCTET STRING
  adnAtmAccLocalVpi INTEGER
  adnAtmAccLocalVci INTEGER
  adnAtmAccRemVpi INTEGER
  adnAtmAccRemVci INTEGER
  adnAtmAccConnUniqueID INTEGER
  adnAtmAccConnStartTime INTEGER
  adnAtmAccConnDuration INTEGER -2147483648..2147483647
  adnAtmAccReqTransitDelay INTEGER
  adnAtmAccCumulTransitDelay INTEGER
  adnAtmAccTransferCapability INTEGER
  adnAtmAccTrmTrafficDescrType INTEGER
  adnAtmAccTrmParam1 INTEGER
  adnAtmAccTrmParam2 INTEGER
  adnAtmAccTrmParam3 INTEGER
  adnAtmAccTrmParam4 INTEGER
  adnAtmAccTrmTagging INTEGER
  adnAtmAccTrmPacketDiscard INTEGER
  adnAtmAccRcvTrafficDescrType INTEGER
  adnAtmAccRcvParam1 INTEGER
  adnAtmAccRcvParam2 INTEGER
  adnAtmAccRcvParam3 INTEGER
  adnAtmAccRcvParam4 INTEGER
  adnAtmAccRcvTagging INTEGER
  adnAtmAccRcvPacketDiscard INTEGER
  adnAtmAccClearingCause INTEGER
  adnAtmAccClearingDiag INTEGER -2147483648..2147483647
  adnAtmAccVcDescriptor OCTET STRING

AdnIpIfStackEntry  
SEQUENCE    
  adnIpIfStackHigherLayer INTEGER -2147483648..2147483647
  adnIpIfStackLowerLayer INTEGER -2147483648..2147483647
  adnIpIfStackStatus RowStatus

AdnCvsiCos  
INTEGER cos0(1), cos7(2), other(3)    

AdnTdpIfEntry  
SEQUENCE    
  adnTdpIfLogicalNum INTEGER -2147483648..2147483647
  adnTdpIfPhyDesc OCTET STRING
  adnTdpIfType INTEGER
  adnTdpIfState INTEGER
  adnTdpIfTrapSent INTEGER
  adnTdpIfPhyIfIndex InterfaceIndex
  adnTdpIfPhyVpi INTEGER -2147483648..2147483647
  adnTdpIfIuniIfIndex InterfaceIndex
  adnTdpIfVciMax INTEGER -2147483648..2147483647
  adnTdpIfVciMin INTEGER -2147483648..2147483647
  adnTdpIfMaxTDPConn INTEGER -2147483648..2147483647
  adnTdpIfAvailConnEgress INTEGER -2147483648..2147483647
  adnTdpIfAvailConnIn INTEGER -2147483648..2147483647
  adnTdpIfMaxCellRateEgress INTEGER -2147483648..2147483647
  adnTdpIfMaxCellRateIn INTEGER -2147483648..2147483647
  adnTdpIfAvailCellRateEgress INTEGER -2147483648..2147483647
  adnTdpIfAvailCellRateIn INTEGER -2147483648..2147483647
  adnTdpIfMaxCtdEgress INTEGER -2147483648..2147483647
  adnTdpIfMaxCtdIn INTEGER -2147483648..2147483647
  adnTdpIfMaxCdvEgress INTEGER -2147483648..2147483647
  adnTdpIfMaxCdvIn INTEGER -2147483648..2147483647
  adnTdpIfRemoteLogicalNum INTEGER -2147483648..2147483647
  adnTdpIfRemoteNodeId AdnRoutingID
  adnTdpIfPolicingState AdnEnableDisabled
  adnTdpIfPCR INTEGER -2147483648..2147483647
  adnTdpIfABW INTEGER -2147483648..2147483647
  adnTdpIfRemNodeMacNum INTEGER -2147483648..2147483647
  adnTdpIfRemNodeAreaNum INTEGER -2147483648..2147483647

AdnTdpIfLookupEntry  
SEQUENCE    
  adnTdpIfIndex InterfaceIndex

AdnAtmTdpConnEntry  
SEQUENCE    
  adnAtmTdpConnVpi INTEGER
  adnAtmTdpConnVci INTEGER
  adnAtmTdpConnCconnectIndex INTEGER
  adnAtmTdpConnPriSec INTEGER
  adnAtmTdpConnOutIfIndex InterfaceIndex
  adnAtmTdpConnOutVpi INTEGER
  adnAtmTdpConnOutVci INTEGER
  adnAtmTdpConnOutCconnectIndex INTEGER
  adnAtmTdpConnState INTEGER
  adnAtmTdpConnForwCellRate INTEGER -2147483648..2147483647
  adnAtmTdpConnForwPCR INTEGER -2147483648..2147483647
  adnAtmTdpConnForwDelay INTEGER -2147483648..2147483647
  adnAtmTdpConnForwDelayVariation INTEGER -2147483648..2147483647
  adnAtmTdpConnRevCellRate INTEGER -2147483648..2147483647
  adnAtmTdpConnRevPCR INTEGER -2147483648..2147483647
  adnAtmTdpConnRevDelay INTEGER -2147483648..2147483647
  adnAtmTdpConnRevDelayVariation INTEGER -2147483648..2147483647
  adnAtmTdpConnPriPersEPFlag INTEGER
  adnAtmTdpConnSecPersEPFlag INTEGER
  adnAtmTdpConnForwSCR INTEGER -2147483648..2147483647
  adnAtmTdpConnForwMBS INTEGER -2147483648..2147483647
  adnAtmTdpConnRevSCR INTEGER -2147483648..2147483647
  adnAtmTdpConnRevMBS INTEGER -2147483648..2147483647
  adnAtmTdpConnForwServType INTEGER
  adnAtmTdpConnRevServType INTEGER

AdnIpRouteNodeEntry  
SEQUENCE    
  adnIpRouteConfigIndex INTEGER -2147483648..2147483647
  adnIpRouteConfigFilePtr DisplayString
  adnIpRouteConfigAdminState INTEGER -2147483648..2147483647
  adnIpRouteConfigOperState INTEGER -2147483648..2147483647

Defined Values

alcatel 3.1.637
OBJECT IDENTIFIER    

adn 3.1.637.3
OBJECT IDENTIFIER    

adnMIB 3.1.637.3.1
OBJECT IDENTIFIER    

adnVersion 3.1.637.3.1.1
OBJECT IDENTIFIER    

adnEquipment 3.1.637.3.1.2
OBJECT IDENTIFIER    

adnExperimental 3.1.637.3.1.3
OBJECT IDENTIFIER    

adnExtensions 3.1.637.3.1.4
OBJECT IDENTIFIER    

adnProprietary 3.1.637.3.1.5
OBJECT IDENTIFIER    

adnMIBTraps 3.1.637.3.1.6
OBJECT IDENTIFIER    

adnMIBConformance 3.1.637.3.1.7
OBJECT IDENTIFIER    

adnEnvironment 3.1.637.3.1.8
OBJECT IDENTIFIER    

adnErrors 3.1.637.3.1.9
OBJECT IDENTIFIER    

adnTpxAgent 3.1.637.3.1.1.1
OBJECT IDENTIFIER    

adnHssAgent 3.1.637.3.1.1.2
OBJECT IDENTIFIER    

adnPsxAcxAgent 3.1.637.3.1.1.3
OBJECT IDENTIFIER    

adnNmsVpnAgent 3.1.637.3.1.1.4
OBJECT IDENTIFIER    

adnNode 3.1.637.3.1.2.1
OBJECT IDENTIFIER    

adnCard 3.1.637.3.1.2.2
OBJECT IDENTIFIER    

adnInterface 3.1.637.3.1.2.3
OBJECT IDENTIFIER    

adnProcessor 3.1.637.3.1.2.4
OBJECT IDENTIFIER    

adnChassis 3.1.637.3.1.2.5
OBJECT IDENTIFIER    

adnAeiPort 3.1.637.3.1.2.6
OBJECT IDENTIFIER    

adnIosPort 3.1.637.3.1.2.7
OBJECT IDENTIFIER    

adnApplique 3.1.637.3.1.2.8
OBJECT IDENTIFIER    

adn3rdPartyInterface 3.1.637.3.1.2.9
OBJECT IDENTIFIER    

adnTp4900 3.1.637.3.1.2.1.1
OBJECT IDENTIFIER    

adnTp8000 3.1.637.3.1.2.1.2
OBJECT IDENTIFIER    

adnTp4800 3.1.637.3.1.2.1.3
OBJECT IDENTIFIER    

adnTp3000 3.1.637.3.1.2.1.4
OBJECT IDENTIFIER    

adnHSS 3.1.637.3.1.2.1.5
OBJECT IDENTIFIER    

adnHSS1X 3.1.637.3.1.2.1.6
OBJECT IDENTIFIER    

adnPsx 3.1.637.3.1.2.1.7
OBJECT IDENTIFIER    

adnAcx 3.1.637.3.1.2.1.8
OBJECT IDENTIFIER    

adnHSS400 3.1.637.3.1.2.1.5.1
OBJECT IDENTIFIER    

adnHSS700 3.1.637.3.1.2.1.5.2
OBJECT IDENTIFIER    

adnHSSChassis 3.1.637.3.1.2.5.5
OBJECT IDENTIFIER    

adn3Coupler 3.1.637.3.1.2.5.5.1
OBJECT IDENTIFIER    

adn8Coupler 3.1.637.3.1.2.5.5.2
OBJECT IDENTIFIER    

adn12Coupler 3.1.637.3.1.2.5.5.3
OBJECT IDENTIFIER    

adnLpu 3.1.637.3.1.2.2.1
OBJECT IDENTIFIER    

adnMsc 3.1.637.3.1.2.2.2
OBJECT IDENTIFIER    

adnHsc 3.1.637.3.1.2.2.3
OBJECT IDENTIFIER    

adnIwc 3.1.637.3.1.2.2.4
OBJECT IDENTIFIER    

adnAse 3.1.637.3.1.2.2.5
OBJECT IDENTIFIER    

adnCu 3.1.637.3.1.2.2.6
OBJECT IDENTIFIER    

adnHbsac 3.1.637.3.1.2.2.7
OBJECT IDENTIFIER    

adn3rdParty 3.1.637.3.1.2.2.8
OBJECT IDENTIFIER    

adnPsxCard 3.1.637.3.1.2.2.9
OBJECT IDENTIFIER    

adnAcxCard 3.1.637.3.1.2.2.10
OBJECT IDENTIFIER    

adnSync 3.1.637.3.1.2.2.11
OBJECT IDENTIFIER    

adnHbcp8 3.1.637.3.1.2.2.2.1
OBJECT IDENTIFIER    

adnHb2t1 3.1.637.3.1.2.2.2.2
OBJECT IDENTIFIER    

adnHb2e1 3.1.637.3.1.2.2.2.3
OBJECT IDENTIFIER    

adnHb8ce 3.1.637.3.1.2.2.2.4
OBJECT IDENTIFIER    

adnHb8ct 3.1.637.3.1.2.2.2.5
OBJECT IDENTIFIER    

adnHb8cu 3.1.637.3.1.2.2.2.6
OBJECT IDENTIFIER    

adnHb8t1 3.1.637.3.1.2.2.2.7
OBJECT IDENTIFIER    

adnHb8e1 3.1.637.3.1.2.2.2.8
OBJECT IDENTIFIER    

adnBbe3b 3.1.637.3.1.2.2.3.1
OBJECT IDENTIFIER    

adnBbe3b3 3.1.637.3.1.2.2.3.1.1
OBJECT IDENTIFIER    

adnBbt3b 3.1.637.3.1.2.2.3.2
OBJECT IDENTIFIER    

adnBbt3b3 3.1.637.3.1.2.2.3.2.1
OBJECT IDENTIFIER    

adnBbs1b 3.1.637.3.1.2.2.3.3
OBJECT IDENTIFIER    

adnBbs1b3 3.1.637.3.1.2.2.3.3.1
OBJECT IDENTIFIER    

adnBbe1b 3.1.637.3.1.2.2.3.4
OBJECT IDENTIFIER    

adnBbt1b 3.1.637.3.1.2.2.3.5
OBJECT IDENTIFIER    

adnBbs1b2 3.1.637.3.1.2.2.3.6
OBJECT IDENTIFIER    

adnBbs1b4 3.1.637.3.1.2.2.3.6.1
OBJECT IDENTIFIER    

adnBbt3b2 3.1.637.3.1.2.2.3.7
OBJECT IDENTIFIER    

adnBbt3b4 3.1.637.3.1.2.2.3.7.1
OBJECT IDENTIFIER    

adnHbcet 3.1.637.3.1.2.2.3.8
OBJECT IDENTIFIER    

adnHbcee 3.1.637.3.1.2.2.3.9
OBJECT IDENTIFIER    

adnHbceu 3.1.637.3.1.2.2.3.10
OBJECT IDENTIFIER    

adnBbs4b 3.1.637.3.1.2.2.3.11
OBJECT IDENTIFIER    

adnBbs4b2 3.1.637.3.1.2.2.3.12
OBJECT IDENTIFIER    

adnBbts1c 3.1.637.3.1.2.2.3.13
OBJECT IDENTIFIER    

adnBbtp3c 3.1.637.3.1.2.2.3.14
OBJECT IDENTIFIER    

adnHbcig1 3.1.637.3.1.2.2.4.1
OBJECT IDENTIFIER    

adnHbcigr 3.1.637.3.1.2.2.4.2
OBJECT IDENTIFIER    

adnHbcig3 3.1.637.3.1.2.2.4.3
OBJECT IDENTIFIER    

adnHbcig4 3.1.637.3.1.2.2.4.4
OBJECT IDENTIFIER    

adnNb41b 3.1.637.3.1.2.2.6.1
OBJECT IDENTIFIER    

adnNb51b 3.1.637.3.1.2.2.6.2
OBJECT IDENTIFIER    

adnBbase3 3.1.637.3.1.2.2.5.1
OBJECT IDENTIFIER    

adnBbaseb 3.1.637.3.1.2.2.5.1.1
OBJECT IDENTIFIER    

adnBbaseb1 3.1.637.3.1.2.2.5.1.2
OBJECT IDENTIFIER    

adnBbsyn 3.1.637.3.1.2.2.11.1
OBJECT IDENTIFIER    

adnCiscoIr 3.1.637.3.1.2.2.8.1
OBJECT IDENTIFIER    

adnHb2et 3.1.637.3.1.2.2.8.1.1
OBJECT IDENTIFIER    

adnHb2tr 3.1.637.3.1.2.2.8.1.2
OBJECT IDENTIFIER    

adnTelogyVs 3.1.637.3.1.2.2.8.2
OBJECT IDENTIFIER    

adnHbvss8 3.1.637.3.1.2.2.8.2.1
OBJECT IDENTIFIER    

adnHbvss16 3.1.637.3.1.2.2.8.2.2
OBJECT IDENTIFIER    

adnPac 3.1.637.3.1.2.2.10.1
OBJECT IDENTIFIER    

adnLac4 3.1.637.3.1.2.2.10.2
OBJECT IDENTIFIER    

adnLac8 3.1.637.3.1.2.2.10.3
OBJECT IDENTIFIER    

adnAcx8 3.1.637.3.1.2.2.10.4
OBJECT IDENTIFIER    

adnCs 3.1.637.3.1.2.2.9.1
OBJECT IDENTIFIER    

adnCbs 3.1.637.3.1.2.2.9.2
OBJECT IDENTIFIER    

adnUtr 3.1.637.3.1.2.2.9.3
OBJECT IDENTIFIER    

adnFtd 3.1.637.3.1.2.2.9.4
OBJECT IDENTIFIER    

adnCtuj 3.1.637.3.1.2.2.9.5
OBJECT IDENTIFIER    

adnMc4 3.1.637.3.1.2.2.9.6
OBJECT IDENTIFIER    

adnCbx 3.1.637.3.1.2.2.9.7
OBJECT IDENTIFIER    

adnDcFtd 3.1.637.3.1.2.2.9.8
OBJECT IDENTIFIER    

adnDclmg 3.1.637.3.1.2.2.9.9
OBJECT IDENTIFIER    

adnCts 3.1.637.3.1.2.2.9.10
OBJECT IDENTIFIER    

adnCmic 3.1.637.3.1.2.2.9.11
OBJECT IDENTIFIER    

adnCtj64 3.1.637.3.1.2.2.9.12
OBJECT IDENTIFIER    

adnAcTuj 3.1.637.3.1.2.2.9.13
OBJECT IDENTIFIER    

adnDcv35 3.1.637.3.1.2.2.9.14
OBJECT IDENTIFIER    

adnDcv11 3.1.637.3.1.2.2.9.15
OBJECT IDENTIFIER    

adnAcj64 3.1.637.3.1.2.2.9.16
OBJECT IDENTIFIER    

adnImc 3.1.637.3.1.2.2.9.17
OBJECT IDENTIFIER    

adnCts1 3.1.637.3.1.2.2.9.18
OBJECT IDENTIFIER    

adnCts2 3.1.637.3.1.2.2.9.19
OBJECT IDENTIFIER    

adnCtas 3.1.637.3.1.2.2.9.20
OBJECT IDENTIFIER    

adnCts1b 3.1.637.3.1.2.2.9.21
OBJECT IDENTIFIER    

adnCUMain 3.1.637.3.1.2.4.1
OBJECT IDENTIFIER    

adnOM 3.1.637.3.1.2.4.2
OBJECT IDENTIFIER    

adnXP 3.1.637.3.1.2.4.3
OBJECT IDENTIFIER    

adnET 3.1.637.3.1.2.4.4
OBJECT IDENTIFIER    

adnAX 3.1.637.3.1.2.4.5
OBJECT IDENTIFIER    

adnSE 3.1.637.3.1.2.4.6
OBJECT IDENTIFIER    

adnSY 3.1.637.3.1.2.4.7
OBJECT IDENTIFIER    

adnTransmission 3.1.637.3.1.4.10
OBJECT IDENTIFIER    

adnIfMIB 3.1.637.3.1.4.31
OBJECT IDENTIFIER    

adnTrapsCommon 3.1.637.3.1.6.1
OBJECT IDENTIFIER    

adnTrapsFrameRelay 3.1.637.3.1.6.2
OBJECT IDENTIFIER    

adnTrapsATM 3.1.637.3.1.6.3
OBJECT IDENTIFIER    

adnTrapsTDM 3.1.637.3.1.6.4
OBJECT IDENTIFIER    

adnTrapVars 3.1.637.3.1.6.5
OBJECT IDENTIFIER    

adnTrapsPsxAcx 3.1.637.3.1.6.6
OBJECT IDENTIFIER    

adnProtocols 3.1.637.3.1.5.4
OBJECT IDENTIFIER    

adnNmsVpn 3.1.637.3.1.5.21
OBJECT IDENTIFIER    

adnEnvTp4900 3.1.637.3.1.8.1
OBJECT IDENTIFIER    

adnEnvTp8000 3.1.637.3.1.8.2
OBJECT IDENTIFIER    

adnEnvTp4800 3.1.637.3.1.8.3
OBJECT IDENTIFIER    

adnEnvTp3000 3.1.637.3.1.8.4
OBJECT IDENTIFIER    

adnEnvHss 3.1.637.3.1.8.5
OBJECT IDENTIFIER    

adnEnvPsx 3.1.637.3.1.8.6
OBJECT IDENTIFIER    

adnEnvAcx 3.1.637.3.1.8.7
OBJECT IDENTIFIER    

adnUCNodeErrors 3.1.637.3.1.9.1
OBJECT IDENTIFIER    

adnRoutingCriteria 3.1.637.3.1.10
OBJECT IDENTIFIER    

adnFrnetservMIB 3.1.637.3.1.4.10.44
OBJECT IDENTIFIER    

adnFrChanTable 3.1.637.3.1.4.10.44.1
This table is an extension of the Frame Relay Management Signalling Group table and the Frame Relay Logical Port Group table from RFC1604.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrChanEntry

adnFrChanEntry 3.1.637.3.1.4.10.44.1.1
An entry in the channel table. There will be one entry for each FRS (Frame Relay Service) channel configured.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrChanEntry  

adnFrChanBAT 3.1.637.3.1.4.10.44.1.1.1
This is the bandwidth allocation threshold for the channel. A value exceeding 80% is not recommended for sustained traffic loads. Common Name: BAT(%)
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnPercent  

adnFrChanAccounting 3.1.637.3.1.4.10.44.1.1.2
This indicates if accounting is enabled for the VCs on this channel. Common Name: Accounting
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFrChanStatistics 3.1.637.3.1.4.10.44.1.1.3
This indicates if statistics are enabled for this channel. When enabled, performance information is reported to the NMS. Common Name: Statistics
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFrChanLineType 3.1.637.3.1.4.10.44.1.1.4
This indicates if this channel is a FRIC (frame relay interface code) or FRAD (frame relay assembler/disassembler) or a frx channel. FRIC allows devices to use the frame relay backbone with Q.922A frames. FRAD allows any HDLC-compatible device to use frame relay by encapsulating the HDLC frame with the required Q.922A frame. FRX allows PSX switches to connect to a HSS switch as a special access devices. IP (Internet Protocol) indicates this channel allows IP services. Common Name: Line Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), fric(2), frad(3), frx(4), ip(5)  

adnFrChanCongsState 3.1.637.3.1.4.10.44.1.1.5
This indicates the congestion level of this channel in the egress direction. Depending on the congestion level, some frames may be discarded. Frames are discarded according to a priority scheme. Note that an idle channel may also be classified as congested due to restricted internal resources. Common Name: Egress Congestion Level
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnCongestLevels  

adnFrChanProced 3.1.637.3.1.4.10.44.1.1.6
The value of this object identifies the LIS (local in-channel signalling) procedure that is used for this UNI/NNI logical port. The UNI/NNI logical port can be performing user-to-network network-side procedures, bidirectional, user-to-network user-side procedures, or other. This object is configured and replaces frMgtVCSigProced, which is not configured. frMgtVCSigProced is readable via SNMP and mirrors this object. Common Name: LIS Interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER u2nnet(1), bidirect(2), u2nuser(50), other(51)  

adnFrChanVCTraps 3.1.637.3.1.4.10.44.1.1.7
This indicates whether or not VC-level traps and alarms are reported for this channel. If disabled, then no VC-level traps or alarms will be reported by any VC on this channel. Common Name: VC Traps
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFrChanNxOverBcs 3.1.637.3.1.4.10.44.1.1.9
This indicates the number of times Bcs (statistically- committed data rate) can be over-subscribed for user traffic on this channel. Common Name: # Times Over Subscribe Bcs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanNxOverBe 3.1.637.3.1.4.10.44.1.1.10
This indicates the number of times Be (excess burst data rate) can be over-subscribed for user traffic on this channel. Common Name: # Times Over Subscribe Be
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanInCIR 3.1.637.3.1.4.10.44.1.1.11
This contains the ingress CIR (committed information rate) of all calls that are active on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanInBc 3.1.637.3.1.4.10.44.1.1.12
This contains the ingress Bc (committed data rate) of all calls that are active on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanInBcs 3.1.637.3.1.4.10.44.1.1.13
This contains the ingress Bcs (statistically-committed data rate) of all calls that are active on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanInBe 3.1.637.3.1.4.10.44.1.1.14
This contains the ingress Be (excess burst data rate) of all calls that are active on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanOutCIR 3.1.637.3.1.4.10.44.1.1.15
This contains the egress CIR (Committed Information Rate) of all calls that are active on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanOutBc 3.1.637.3.1.4.10.44.1.1.16
This contains the egress Bc of all calls that are active on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanOutBcs 3.1.637.3.1.4.10.44.1.1.17
This contains the egress Bcs of all calls that are active on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanOutBe 3.1.637.3.1.4.10.44.1.1.18
This contains the egress Be of all calls that are active on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanNumCallActive 3.1.637.3.1.4.10.44.1.1.19
This contains the number of calls that are active on this channel. This only includes calls that are in the data transfer state. The object adnFrVCOperState will be 'up(1)'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanDelaySensitive 3.1.637.3.1.4.10.44.1.1.20
This field indicates whether VCs set up on this channel are delay sensitive. If this field is set to 'true(1)' then path selection for all VCs on this channel will be based on the criterion (delay, monetary cost, hops). Otherwise the value of adnFrVCDelaySensitive for each VC will be used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TruthValue  

adnFrChanVCTypeConfigured 3.1.637.3.1.4.10.44.1.1.21
This object specifies the types of VCs allowed on this channel/port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), pvcOnly(2), svcOnly(3), pvcAndSvc(4)  

adnFrChanPVCMaxNumAllowed 3.1.637.3.1.4.10.44.1.1.22
This is the maximum number of PVCs that can be configured on the channel.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanPVCBidirLow 3.1.637.3.1.4.10.44.1.1.23
The value of this object is used to indicate the lower number for the range of bi-directional PVC DLCIs. This number is only valid if adnFrChanVCTypeConfigured allows PVCs on this channel and adnFrChanPVCMaxNumAllowed is greater than 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanPVCBidirHigh 3.1.637.3.1.4.10.44.1.1.24
The value of this object is used to indicate the higher number for the range of bi-directional PVC DLCIs. This number is only valid if adnFrChanVCTypeConfigured allows PVCs on this channel and adnFrChanPVCMaxNumAllowed is greater than 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCMaxNumAllowed 3.1.637.3.1.4.10.44.1.1.25
This is the maximum number of SVC user calls allowed on the channel.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCBidirLow 3.1.637.3.1.4.10.44.1.1.26
The value of this object is used to indicate the lower number for the range of bi-directional SVC DLCIs. This number is only valid if adnFrChanVCTypeConfigured allows SVCs on this channel and adnFrChanSVCMaxNumAllowed is greater than 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCBidirHigh 3.1.637.3.1.4.10.44.1.1.27
The value of this object is used to indicate the higher number for the range of bi-directional SVC DLCIs. This number is only valid if adnFrChanVCTypeConfigured allows SVCs on this channel and adnFrChanSVCMaxNumAllowed is greater than 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCUserNetFlg 3.1.637.3.1.4.10.44.1.1.28
This indicates whether the interface follows the user or network side of the protocol recommendations. Common Name: User/Network Protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER user(1), network(2)  

adnFrChanSVCT303 3.1.637.3.1.4.10.44.1.1.29
This timer specifies the amount of time to wait for a setup response. If the timer expires, then the setup message is retransmitted. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCT305 3.1.637.3.1.4.10.44.1.1.30
This timer specifies the amount of time to wait for a disconnect response. If the timer expires, then the release message is transmitted. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCT308 3.1.637.3.1.4.10.44.1.1.31
This timer specifies the amount of time to wait for a release response. If the timer expires the first time, then the release message is retransmitted. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCT309 3.1.637.3.1.4.10.44.1.1.32
This data link timer specifies the amount of time to wait for re-establishment of the LAPD (link access procedure on the D-channel) link. If the timer expires, all calls will be cleared. Otherwise, calls in stable states are not lost. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCT310 3.1.637.3.1.4.10.44.1.1.33
This timer specifies the amount of time to wait for a connect or disconnect after receiving a Call Proceeding. If the timer expires, then the call is cleared by transmitting a disconnect message. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCT313 3.1.637.3.1.4.10.44.1.1.34
This timer specifies the amount of time to wait for a connect response. If the timer expires, then the call is cleared by transmitting a disconnect message. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCT315 3.1.637.3.1.4.10.44.1.1.35
This timer specifies the amount of time to wait for a status inquiry response. If the timer expires, then the call is cleared by transmitting a disconnect message. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCT316 3.1.637.3.1.4.10.44.1.1.36
This timer specifies the amount of time to wait for a restart response. If the timer expires, then the restart message is re-transmitted. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCT317 3.1.637.3.1.4.10.44.1.1.37
Reserved for future use. This restart confirm timer specifies the amount of time to wait for clearing all the calls. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCT320 3.1.637.3.1.4.10.44.1.1.38
Reserved for future use. This inactivity timer specifies the amount of time to wait for a response to a call. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCInCallBr 3.1.637.3.1.4.10.44.1.1.39
This specifies that call setup messages incoming to the DTE (from the frame relay network) are not allowed and will be cleared at the destination. Common Name: Incoming Calls Barred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnFrChanSVCOutCallBr 3.1.637.3.1.4.10.44.1.1.40
This specifies that call setup messages outgoing from the DTE (to the frame relay network) are not allowed and will be cleared at the source. Common Name: Outgoing Calls Barred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnFrChanSVCAddrValid 3.1.637.3.1.4.10.44.1.1.41
This specifies whether the calling party address in the setup message will be compared to the source channel address(es) and whether the connected number in the connect message will be compared to the destination channel address(es).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnFrChanSVCAddrLenIg 3.1.637.3.1.4.10.44.1.1.42
This specifies the number of least significant bits in the address field of the Q.933 SETUP/CONNECT message should be ignored.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCMaxNumActive 3.1.637.3.1.4.10.44.1.1.43
This is the count of the maximum number of SVCs active at one time.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCCurrentActive 3.1.637.3.1.4.10.44.1.1.44
Count of the current number of active SVCs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCTotalProcessed 3.1.637.3.1.4.10.44.1.1.45
Count of the total number of SVCs that have been processed.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCFailedClrNet 3.1.637.3.1.4.10.44.1.1.46
Count of failed SVCs that were cleared by the network.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCFailedClrDTE 3.1.637.3.1.4.10.44.1.1.47
Count of failed SVCs that were cleared by the DTE.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCSuccessClrNet 3.1.637.3.1.4.10.44.1.1.48
Count of successful SVCs cleared by the network.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCSuccessClrDTE 3.1.637.3.1.4.10.44.1.1.49
Count of the successful SVCs cleared by the DTE.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCMaxAggActCIR 3.1.637.3.1.4.10.44.1.1.50
Maximum aggregate CIR for active SVCs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanPVCMaxAggActCIR 3.1.637.3.1.4.10.44.1.1.51
Maximum aggregate CIR for active PVCs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanSVCMaxAggNormBe 3.1.637.3.1.4.10.44.1.1.52
Maximum aggregate normalized Be (Bc/Tc) for active SVCs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanPVCMaxAggNormBe 3.1.637.3.1.4.10.44.1.1.53
Maximum aggregate normalized Be (Bc/Tc) for active PVCs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanDefaultCos 3.1.637.3.1.4.10.44.1.1.54
This indicates the Class of Service (COS) for this channel. adnFrChanDefaultCos will be used for SVCs and all VCs received through a TPX Gateway. PVCs will use the COS defined in adnFrVCCos.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnFrCos  

adnFrChanNumofMSN 3.1.637.3.1.4.10.44.1.1.55
This specifies the number of Multiple Subscriber Numbers (MSN) that can be configured on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanNxMultiBc 3.1.637.3.1.4.10.44.1.1.56
This indicates the number of times Bc (committed data rate) can be over-subscribed for user traffic on this channel. Common Name: # Times Over Subscribe Bc
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanMaxBcAllPVCs 3.1.637.3.1.4.10.44.1.1.57
This field represents the maximum value of adnFrVCOutBc of all PVCs configured for the channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanMaxBcsAllPVCs 3.1.637.3.1.4.10.44.1.1.58
This field represents the maximum value of adnFrPVCOutBcs of all PVCs configured for the channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanCosRtBcEgress 3.1.637.3.1.4.10.44.1.1.59
This is the sum of committed egress bandwidth for Class of Service (COS) 'cosRt(1)'. Common Name: COS Real Time Commit Egress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanCosRtBcIngress 3.1.637.3.1.4.10.44.1.1.60
This is the sum of committed ingress bandwidth for Class of Service (COS) 'cosRt(1)'. Common Name: COS Real Time Bc Commit Ingress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanCosNrtBcEgress 3.1.637.3.1.4.10.44.1.1.61
This is the sum of committed egress bandwidth for Class of Service (COS) 'cosNrt(2)'. Common Name: COS Non Real Time Bc Commit Egress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanCosNrtBcIngress 3.1.637.3.1.4.10.44.1.1.62
This is the sum of committed ingress bandwidth for Class of Service (COS) 'cosNrt(2)'. Common Name: COS Non Real Time Bc Commit Ingress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanBwAllocated 3.1.637.3.1.4.10.44.1.1.63
This is the bandwidth allocated to all VCs on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrChanBwAvail 3.1.637.3.1.4.10.44.1.1.64
This is the bandwidth available to this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCTable 3.1.637.3.1.4.10.44.2
These are the PVC table extensions to the PVC End-Point table in RFC1604. This table is used for PVCs and SVCs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrVCEntry

adnFrVCEntry 3.1.637.3.1.4.10.44.2.1
VC table entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrVCEntry  

adnFrVCRemNodeID 3.1.637.3.1.4.10.44.2.1.1
This is the routing node ID of the destination node for this VC. It is an integer that ROUTES (HSS routing application) uses to route this call to the proper destination node. Common Name: Remote Node ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnFrVCRemNumPlan 3.1.637.3.1.4.10.44.2.1.2
This is the numbering plan of the interface on the node at the remote end of the VC. Common Name: Remote Numbering Plan
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), e164(2), x121(3), none(4)  

adnFrVCRemPhysAddress 3.1.637.3.1.4.10.44.2.1.3
This is the address of the interface on the node at the remote end of the VC. The numbering plan for that interface is given by the value of adnFrVCRemNumPlan. Common Name: Remote address
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

adnFrVCRemDlci 3.1.637.3.1.4.10.44.2.1.4
This is the DLCI (data link connection identifier) of this VC on the interface on the node at the remote end of the VC. Common Name: Remote DLCI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCAdminState 3.1.637.3.1.4.10.44.2.1.5
The desired state of this call. Common Name: Status Administrative, Administrative
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnFrVCOperState 3.1.637.3.1.4.10.44.2.1.6
The current state of this call. Common Name: Status Operational, Operational
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnFrVCTime 3.1.637.3.1.4.10.44.2.1.7
The time the VC was initialized. For a PVC, this is the time the PVC was configured. Common Name: Last Change
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnFrVCInBcs 3.1.637.3.1.4.10.44.2.1.8
This specifies the Bcs (statistically-committed data rate) for ingress data. Common Name: Ingress Bcs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCOutBcs 3.1.637.3.1.4.10.44.2.1.9
This specifies the Bcs (statistically-committed data rate) for egress data. Common Name: Egress Bcs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCUserOrNet 3.1.637.3.1.4.10.44.2.1.10
This indicates if this is a User or Network call. The priority given to each type of call's data in the network differs. Common Name: Type of Call
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER usercall(1), networkcall(2)  

adnFrVCLisDiscard 3.1.637.3.1.4.10.44.2.1.11
This object indicates whether FRS should discard ingress data if the LIS (Local In-channel Signalling) status for this PVC is inactive. If this is 'discard(1)' and the local or remote LIS status is down, then ingress data is discarded. If this is 'nodiscard(2)', then regardless of LIS status, the ingress data is not discarded. Common Name: LIS Discard Action
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER discard(1), nodiscard(2)  

adnFrVCRetryAttempts 3.1.637.3.1.4.10.44.2.1.12
This specifies the number of PVC call attempts to make at the fast rate (adnFrVCFastRetry) before slowing the call attempt rate to adnFrVCSlowRetry. This only has significance if adnFrVCSourceDest is 'source(1)'. The current attempt state is in adnFrVCAttemptState. Common Name: Fast Rate Retry
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCFastRetry 3.1.637.3.1.4.10.44.2.1.13
This timer specifies the amount of time to wait between failed PVC setup attempts. After attempting this rate for adnFrVCRetryAttempts times, the rate will be slowed to adnFrVCSlowRetry. This only has significance if adnFrVCSourceDest is 'source(1)'. Common Name: Fast Rate Retry Timer
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCSlowRetry 3.1.637.3.1.4.10.44.2.1.14
This timer specifies the amount of time to wait between failed PVC setup attempts. After attempting the adnFrVCFastRetry rate for adnFrVCRetryAttempts times, the rate will be slowed to adnFrVCSlowRetry. This only has significance if adnFrVCSourceDest is 'source(1)'. Common Name: Slow Rate Retry Timer
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCForcedPath 3.1.637.3.1.4.10.44.2.1.15
This specifies that this PVC has a forced path specified in the adnFrForceRoute table. If this object is set to 'enabled(1)' and there is no adnFrForceEntry for this PVC, then the PVC will be treated as if adnFrVCForcedPath has the value 'disabled(2)'. Common Name: Forced Path
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnFrVCSourceDest 3.1.637.3.1.4.10.44.2.1.16
This object indicates the call direction of this PVC. If it has the value 'source(1)', the FRS (frame relay Subscriber) subsystem will initiate the call. If it has the value 'destination(2)', FRS will wait for an incoming call request. Common Names: Source or Destination, Src/Dest
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER source(1), destination(2)  

adnFrVCFrameIN 3.1.637.3.1.4.10.44.2.1.17
This counts the number of frames forwarded to the network for this VC. Note that the value of frPVCEndptInFrames from RFC1604 gives the frames received from the user. This counter does not include the 'dummy' frames generated by congestion control. It does include the DQ (data qualified) frames, used to exchange status information with the FRS subsystem at the remote end of a call. Common Name: Frame In
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCFrameOUT 3.1.637.3.1.4.10.44.2.1.18
This counts the number of frames received from the network for this VC. Note that the value of frPVCEndptOutFrames from RFC1604 gives the frames sent to the user. This counter does not include the number of 'dummy' frames generated by congestion control. It does include the DQ (data qualified) frames. Common Name: Frame Out
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCSubFrameIN 3.1.637.3.1.4.10.44.2.1.19
This counts the number of sub-frames forwarded to the network for this VC. Note that the value of frAccountPVCInSegments from RFC1604 gives the number of sub-frames received from the user. Common Name: Sub Frame In
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCSubFrameOUT 3.1.637.3.1.4.10.44.2.1.20
This counts the number of sub-frames received from the network for this VC. Note that the value of frAccountPVCOutSegments from RFC1604 gives the number of sub-frames sent to the user. Common Name: Sub Frames Out
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCBeInDiscards 3.1.637.3.1.4.10.44.2.1.21
This indicates the number of ingress Be (excessive burst data rate) frames that were discarded at the interface due to network congestion. Common Name: Be Frame In Discards
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCBcsInDiscards 3.1.637.3.1.4.10.44.2.1.22
This indicates the number of ingress Bcs (statistically- committed data rate) frames that were discarded at the interface due to network congestion. Common Name: Bcs Frame In Discards
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCBcInDiscards 3.1.637.3.1.4.10.44.2.1.23
This indicates the number of ingress Bc (committed data rate) frames that were discarded at the interface due to network congestion. Common Name: Bc Frame In Discards
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCBeOutDiscards 3.1.637.3.1.4.10.44.2.1.24
This indicates the number of egress Be (excessive burst data rate) frames that were discarded at the interface due to network congestion. Common Name: Be Frame Out Discards
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCBcsOutDiscards 3.1.637.3.1.4.10.44.2.1.25
This indicates the number of egress Bcs (statistically- committed data rate) frames that were discarded at the interface due to network congestion. Common Name: Bcs Frame Out Discards
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCBcOutDiscards 3.1.637.3.1.4.10.44.2.1.26
This indicates the number of egress Bc (committed data rate) frames that were discarded at the interface due to network congestion. Common Name: Bc Frame Out Discards
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCInCongsState 3.1.637.3.1.4.10.44.2.1.27
This indicates the congestion level of this VC in the ingress direction. Depending on the congestion level, some frames from the user may be discarded. Frames are discarded according to a priority scheme. Note that an idle VC may also be classified as congested due to restricted internal resources. Common Name: Ingress Congestion Level
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnCongestLevels  

adnFrVCDiscardLisIn 3.1.637.3.1.4.10.44.2.1.28
This indicates the number of ingress frames that were discarded because LIS (local in-channel signalling) declared the PVC inactive. This value will increment only if adnFrVCLisDiscard is set to 'discard(1)'. Common Name: Frames In Discarded (LIS down)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  


adnFrVCNumNodes 3.1.637.3.1.4.10.44.2.1.30
This indicates the number of nodes in the VC connection If adnFrVCOperState is 'up(1)', then this gives the current hop count. If the adnFrVCOperState is not 'up(1)', this this gives the hop count of the last connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCType 3.1.637.3.1.4.10.44.2.1.31
This specifies the type of this connection: other, pvc ( permanent virtual connection ), svc ( switched virtual connection ) or mspvc ( multi-source permanent virtual connection ). Common Name: Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), pvc(2), svc(3), mspvc(4)  

adnFrVCOutifIndex 3.1.637.3.1.4.10.44.2.1.32
This is the ifIndex of the interface on which this VC exits this node away from this VC endpoint. It is usually a trunk interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnFrVCOutDlci 3.1.637.3.1.4.10.44.2.1.33
This is the DLCI (data link connection identifier) of the VC on the interface on which it exits this node away from this VC endpoint. This can be combined with adnFrVCOutifIndex and used for call tracing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCISR 3.1.637.3.1.4.10.44.2.1.34
This is the initial submission rate (ISR) for ingress traffic. When the VC is determined to be idle in the ingress direction, the submission information rate (SIR) is set to the the ISR. Common Name: Initial Submission Rate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCAttemptState 3.1.637.3.1.4.10.44.2.1.35
This contains the current VC call attempt state. This will start out as 'fast(1)' or 'rxcall(3)' depending on adnFrVCSourceDest. If adnFrVCSourceDest has the value 'source(1)', and the call attempt fails adnFrVCRetryAttempt times, then the call will be attempted at the slow rate (adnFrVCSlowRetry) and this object will be set to 'slow(2)'. Common Name: Attempt State
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER fast(1), slow(2), rxcall(3), callup(4)  

adnFrVCStatistics 3.1.637.3.1.4.10.44.2.1.36
This indicates whether statistics are enabled for this VC. If set to 'useChannelValue(3)', this VC uses the value specified by adnFrChanStatistics. Common Name: Statistics
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), useChannelValue(3)  

adnFrVCAccounting 3.1.637.3.1.4.10.44.2.1.37
This indicates whether accounting is enabled for this VC. If it has the value 'useChannelValue(3)', this VC uses the value specified by adnFrChanAccounting. Common Name: Accounting
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), useChannelValue(3)  

adnFrVCUniqueConnID 3.1.637.3.1.4.10.44.2.1.40
This is a unique connection identifier for this VC. This value is exchanged with the remote FRS (Frame Relay Subscriber) at call setup time. Both the local and the remote ends of the VC will report this value in the accounting record.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCLastClrCauseRX 3.1.637.3.1.4.10.44.2.1.42
This is the most recent clearing cause that was received from the network for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCLastClrDiagRX 3.1.637.3.1.4.10.44.2.1.43
This is the most recent clearing diagnostic code that was received from the network for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCLastClrCauseTX 3.1.637.3.1.4.10.44.2.1.44
This is the most recent clearing cause that was transmitted to the network for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCLastClrDiagTX 3.1.637.3.1.4.10.44.2.1.45
This is the most recent clearing diagnostic code that was transmitted to the network for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCRemoteifindex 3.1.637.3.1.4.10.44.2.1.46
This is the ifIndex of the interface on the node at the remote end of the VC. Together the objects adnFrVCRemNodeID, ifIndex, adnFrVCRemoteifindex, frPVCEndptDLCIIndex, adnFrVCRemDlci, and adnFrVCUniqueConnID uniquely identify VCs for accounting and statistics purposes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrPVCEndptXmitdSigStatus 3.1.637.3.1.4.10.44.2.1.47
The value of this object identifies the PVC status sent via the local in-channel signaling procedures for this PVC end-point. If the logical port is performing only user-side procedures, or if the interface is inoperative, then this value should be 'none(4)'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER deleted(1), active(2), inactive(3), none(4)  

adnFrVCInBc 3.1.637.3.1.4.10.44.2.1.48
This specifies the committed burst size (Bc) parameter (measured in bits) for this PVC end-point in the ingress direction (into the frame relay network). This is a measure of the exclusively allocated trunk bandwidth required for the user's committed data. Common Name: Ingress Trunk Bc
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCOutBc 3.1.637.3.1.4.10.44.2.1.49
This specifies the committed burst size (Bc) parameter (measured in bits) for this PVC end-point in the egress direction (out of the frame relay network). This is a measure of the exclusively allocated trunk bandwidth required for the user's committed data. Common Name: Egress Trunk Bc
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCRemNodeMacNum 3.1.637.3.1.4.10.44.2.1.50
The machine number part of adnFrVCRemNodeID, the routing node ID of the node at the remote endpoint of this frame relay VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCRemNodeAreaNum 3.1.637.3.1.4.10.44.2.1.51
The area number part of adnFrVCRemNodeID, the routing node ID of the node at the remote endpoint of this frame relay VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCDelaySensitive 3.1.637.3.1.4.10.44.2.1.52
This field indicates whether the VC is delay sensitive. If either this field or adnFrChanDelaySensitive is set to 'true(1)', then path selection for the VC will be based on the criterion (delay, monetary cost, hops). Otherwise, path selection will be based on the criterion (monetary cost, delay, hops).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TruthValue  

adnFrVCCos 3.1.637.3.1.4.10.44.2.1.53
This indicates the Class of Service (COS) for the PVC. SVCs and calls received through a TPX Gateway use the COS defined in adnFrChanDefaultCos.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnFrCos  

adnFrVCEndptDLCIIndex 3.1.637.3.1.4.10.44.2.1.54
This is a duplicate of frPVCEndptDLCIIndex.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCEndptInMaxFrameSize 3.1.637.3.1.4.10.44.2.1.55
This is a duplicate of frPVCEndptInMaxFrameSize.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCEndptInBc 3.1.637.3.1.4.10.44.2.1.56
This is a duplicate of frPVCEndptInBc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCEndptInBe 3.1.637.3.1.4.10.44.2.1.57
This is a duplicate of frPVCEndptInBe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCEndptInCIR 3.1.637.3.1.4.10.44.2.1.58
This is a duplicate of frPVCEndptInCIR.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCEndptOutMaxFrameSize 3.1.637.3.1.4.10.44.2.1.59
This is a duplicate of frPVCEndptOutMaxFrameSize.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCEndptOutBc 3.1.637.3.1.4.10.44.2.1.60
This is a duplicate of frPVCEndptOutBc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCEndptOutBe 3.1.637.3.1.4.10.44.2.1.61
This is a duplicate of frPVCEndptOutBe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCEndptOutCIR 3.1.637.3.1.4.10.44.2.1.62
This is a duplicate of frPVCEndptOutCIR.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCEndptConnectIdentifier 3.1.637.3.1.4.10.44.2.1.63
This is a duplicate of frPVCEndptConnectIdentifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCEndptRowStatus 3.1.637.3.1.4.10.44.2.1.64
This is a duplicate of frPVCEndptRowStatus.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

adnFrVCEndptRcvdSigStatus 3.1.637.3.1.4.10.44.2.1.65
This is a duplicate of frPVCEndptRcvdSigStatus.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER deleted(1), active(2), inactive(3), none(4)  

adnFrVCEndptInFrames 3.1.637.3.1.4.10.44.2.1.66
This is a duplicate of frPVCEndptInFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCEndptOutFrames 3.1.637.3.1.4.10.44.2.1.67
This is a duplicate of frPVCEndptOutFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCEndptInDEFrames 3.1.637.3.1.4.10.44.2.1.68
This is a duplicate of frPVCEndptInDEFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCEndptInExcessFrames 3.1.637.3.1.4.10.44.2.1.69
This is a duplicate of frPVCEndptInExcessFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCEndptOutExcessFrames 3.1.637.3.1.4.10.44.2.1.70
This is a duplicate of frPVCEndptOutExcessFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCEndptInDiscards 3.1.637.3.1.4.10.44.2.1.71
This is a duplicate of frPVCEndptInDiscards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCEndptInOctets 3.1.637.3.1.4.10.44.2.1.72
This is a duplicate of frPVCEndptInOctets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCEndptOutOctets 3.1.637.3.1.4.10.44.2.1.73
This is a duplicate of frPVCEndptOutOctets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrVCBwAllocated 3.1.637.3.1.4.10.44.2.1.74
This is the bandwidth allocated to this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrVCDescr 3.1.637.3.1.4.10.44.2.1.75
A textual string describing this VC. Common Name: Description
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnCMBfvcadnFrVCTable 3.1.637.3.1.4.10.44.3
These are the VC table extensions to the PVC End-Point table in RFC1604. This table is used for PVCs and SVCs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCMBfvcAdnFrVCEntry

adnCMBfvcadnFrVCEntry 3.1.637.3.1.4.10.44.3.1
VC table entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnCMBfvcAdnFrVCEntry  

adnCMBfvcadnFrVCRemNodeID 3.1.637.3.1.4.10.44.3.1.1
This is a duplicate of adnFrVCRemNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnCMBfvcadnFrVCRemNumPlan 3.1.637.3.1.4.10.44.3.1.2
This is a duplicate of adnFrVCRemNumPlan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), e164(2), x121(3), none(4)  

adnCMBfvcadnFrVCRemPhysAddress 3.1.637.3.1.4.10.44.3.1.3
This is a duplicate of adnFrVCRemPhysAddress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

adnCMBfvcadnFrVCRemDlci 3.1.637.3.1.4.10.44.3.1.4
This is a duplicate of adnFrVCRemDlci.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCAdminState 3.1.637.3.1.4.10.44.3.1.5
This is a duplicate of adnFrVCAdminState.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnCMBfvcadnFrVCOperState 3.1.637.3.1.4.10.44.3.1.6
This is a duplicate of adnFrVCOperState.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnCMBfvcadnFrVCTime 3.1.637.3.1.4.10.44.3.1.7
This is a duplicate of adnFrVCTime.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnCMBfvcadnFrVCInBcs 3.1.637.3.1.4.10.44.3.1.8
This is a duplicate of adnFrVCInBcs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCOutBcs 3.1.637.3.1.4.10.44.3.1.9
This is a duplicate of adnFrVCOutBcs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCUserOrNet 3.1.637.3.1.4.10.44.3.1.10
This is a duplicate of adnFrVCUserOrNet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER usercall(1), networkcall(2)  

adnCMBfvcadnFrVCLisDiscard 3.1.637.3.1.4.10.44.3.1.11
This is a duplicate of adnFrVCLisDiscard.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER discard(1), nodiscard(2)  

adnCMBfvcadnFrVCRetryAttempts 3.1.637.3.1.4.10.44.3.1.12
This is a duplicate of adnFrVCRetryAttempts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCFastRetry 3.1.637.3.1.4.10.44.3.1.13
This is a duplicate of adnFrVCFastRetry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCSlowRetry 3.1.637.3.1.4.10.44.3.1.14
This is a duplicate of adnFrVCSlowRetry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCForcedPath 3.1.637.3.1.4.10.44.3.1.15
This is a duplicate of adnFrVCForcedPath.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnCMBfvcadnFrVCSourceDest 3.1.637.3.1.4.10.44.3.1.16
This is a duplicate of adnFrVCSourceDest.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER source(1), destination(2)  

adnCMBfvcadnFrVCFrameIN 3.1.637.3.1.4.10.44.3.1.17
This is a duplicate of adnFrVCFrameIN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCFrameOUT 3.1.637.3.1.4.10.44.3.1.18
This is a duplicate of adnFrVCFrameOUT.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCSubFrameIN 3.1.637.3.1.4.10.44.3.1.19
This is a duplicate of adnFrVCSubFrameIN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCSubFrameOUT 3.1.637.3.1.4.10.44.3.1.20
This is a duplicate of adnFrVCSubFrameOUT.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCBeInDiscards 3.1.637.3.1.4.10.44.3.1.21
This is a duplicate of adnFrVCBeInDiscards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCBcsInDiscards 3.1.637.3.1.4.10.44.3.1.22
This is a duplicate of adnFrVCBcsInDiscards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCBcInDiscards 3.1.637.3.1.4.10.44.3.1.23
This is a duplicate of adnFrVCBcInDiscards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCBeOutDiscards 3.1.637.3.1.4.10.44.3.1.24
This is a duplicate of adnFrVCBeOutDiscards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCBcsOutDiscards 3.1.637.3.1.4.10.44.3.1.25
This is a duplicate of adnFrVCBcsOutDiscards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCBcOutDiscards 3.1.637.3.1.4.10.44.3.1.26
This is a duplicate of adnFrVCBcOutDiscards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCInCongsState 3.1.637.3.1.4.10.44.3.1.27
This is a duplicate of adnFrVCInCongsState.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnCongestLevels  

adnCMBfvcadnFrVCDiscardLisIn 3.1.637.3.1.4.10.44.3.1.28
This is a duplicate of adnFrVCDiscardLisIn.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  


adnCMBfvcadnFrVCNumNodes 3.1.637.3.1.4.10.44.3.1.30
This is a duplicate of adnFrVCNumNodes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCType 3.1.637.3.1.4.10.44.3.1.31
This is a duplicate of adnFrVCType.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), pvc(2), svc(3), mspvc(4)  

adnCMBfvcadnFrVCOutifIndex 3.1.637.3.1.4.10.44.3.1.32
This is a duplicate of adnFrVCOutifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnCMBfvcadnFrVCOutDlci 3.1.637.3.1.4.10.44.3.1.33
This is a duplicate of adnFrVCOutDlci.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCISR 3.1.637.3.1.4.10.44.3.1.34
This is a duplicate of adnFrVCISR.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCAttemptState 3.1.637.3.1.4.10.44.3.1.35
This is a duplicate of adnFrVCAttemptState.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER fast(1), slow(2), rxcall(3), callup(4)  

adnCMBfvcadnFrVCStatistics 3.1.637.3.1.4.10.44.3.1.36
This is a duplicate of adnFrVCStatistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), useChannelValue(3)  

adnCMBfvcadnFrVCAccounting 3.1.637.3.1.4.10.44.3.1.37
This is a duplicate of adnFrVCAccounting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), useChannelValue(3)  

adnCMBfvcadnFrVCUniqueConnID 3.1.637.3.1.4.10.44.3.1.40
This is a duplicate of adnFrVCUniqueConnID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCLastClrCauseRX 3.1.637.3.1.4.10.44.3.1.42
This is a duplicate of adnFrVCLastClrCauseRX.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCLastClrDiagRX 3.1.637.3.1.4.10.44.3.1.43
This is a duplicate of adnFrVCLastClrDiagRX.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCLastClrCauseTX 3.1.637.3.1.4.10.44.3.1.44
This is a duplicate of adnFrVCLastClrCauseTX.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCLastClrDiagTX 3.1.637.3.1.4.10.44.3.1.45
This is a duplicate of adnFrVCLastClrDiagTX.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCRemoteifindex 3.1.637.3.1.4.10.44.3.1.46
This is a duplicate of adnFrVCRemoteifindex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrPVCEndptXmitdSigStatus 3.1.637.3.1.4.10.44.3.1.47
This is a duplicate of adnFrPVCEndptXmitdSigStatus.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER deleted(1), active(2), inactive(3), none(4)  

adnCMBfvcadnFrVCInBc 3.1.637.3.1.4.10.44.3.1.48
This is a duplicate of adnFrVCInBc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCOutBc 3.1.637.3.1.4.10.44.3.1.49
This is a duplicate of adnFrVCOutBc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCRemNodeMacNum 3.1.637.3.1.4.10.44.3.1.50
This is a duplicate of adnFrVCRemNodeMacNum.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcadnFrVCRemNodeAreaNum 3.1.637.3.1.4.10.44.3.1.51
This is a duplicate of adnFrVCRemNodeAreaNum.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptDLCIIndex 3.1.637.3.1.4.10.44.3.1.52
This is a duplicate of frPVCEndptDLCIIndex.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptInMaxFrameSize 3.1.637.3.1.4.10.44.3.1.53
This is a duplicate of frPVCEndptInMaxFrameSize.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptInBc 3.1.637.3.1.4.10.44.3.1.54
This is a duplicate of frPVCEndptInBc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptInBe 3.1.637.3.1.4.10.44.3.1.55
This is a duplicate of frPVCEndptInBe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptInCIR 3.1.637.3.1.4.10.44.3.1.56
This is a duplicate of frPVCEndptInCIR.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptOutMaxFrameSize 3.1.637.3.1.4.10.44.3.1.57
This is a duplicate of frPVCEndptOutMaxFrameSize.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptOutBc 3.1.637.3.1.4.10.44.3.1.58
This is a duplicate of frPVCEndptOutBc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptOutBe 3.1.637.3.1.4.10.44.3.1.59
This is a duplicate of frPVCEndptOutBe.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptOutCIR 3.1.637.3.1.4.10.44.3.1.60
This is a duplicate of frPVCEndptOutCIR.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptConnectIdentifier 3.1.637.3.1.4.10.44.3.1.61
This is a duplicate of frPVCEndptConnectIdentifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCMBfvcfrPVCEndptRowStatus 3.1.637.3.1.4.10.44.3.1.62
This is a duplicate of frPVCEndptRowStatus.
Status: mandatory Access: read-only
OBJECT-TYPE    
  RowStatus  

adnCMBfvcfrPVCEndptRcvdSigStatus 3.1.637.3.1.4.10.44.3.1.63
This is a duplicate of frPVCEndptRcvdSigStatus.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER deleted(1), active(2), inactive(3), none(4)  

adnCMBfvcfrPVCEndptInFrames 3.1.637.3.1.4.10.44.3.1.64
This is a duplicate of frPVCEndptInFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcfrPVCEndptOutFrames 3.1.637.3.1.4.10.44.3.1.65
This is a duplicate of frPVCEndptOutFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcfrPVCEndptInDEFrames 3.1.637.3.1.4.10.44.3.1.66
This is a duplicate of frPVCEndptInDEFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcfrPVCEndptInExcessFrames 3.1.637.3.1.4.10.44.3.1.67
This is a duplicate of frPVCEndptInExcessFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcfrPVCEndptOutExcessFrames 3.1.637.3.1.4.10.44.3.1.68
This is a duplicate of frPVCEndptOutExcessFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcfrPVCEndptInDiscards 3.1.637.3.1.4.10.44.3.1.69
This is a duplicate of frPVCEndptInDiscards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcfrPVCEndptInOctets 3.1.637.3.1.4.10.44.3.1.70
This is a duplicate of frPVCEndptInOctets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcfrPVCEndptOutOctets 3.1.637.3.1.4.10.44.3.1.71
This is a duplicate of frPVCEndptOutOctets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCMBfvcadnFrVCDelaySensitive 3.1.637.3.1.4.10.44.3.1.72
This is a duplicate of adnFrVCDelaySensitive.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TruthValue  

adnCMBfvcadnFrVCCos 3.1.637.3.1.4.10.44.3.1.73
This is a duplicate of adnFrVCCos.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnFrCos  

adnCMBfvcadnFrVCDescr 3.1.637.3.1.4.10.44.3.1.74
This is a duplicate of adnFrVCDescr.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnFrForceRoute 3.1.637.3.1.4.10.44.4
This table describes the forced path to be used for this PVC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrForceEntry

adnFrForceEntry 3.1.637.3.1.4.10.44.4.1
This is one entry of the Forced Path table for the specified PVC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrForceEntry  

adnFrForceHop 3.1.637.3.1.4.10.44.4.1.1
This is the hop indicator. The value is '1' in the source node and increments for each hop through the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrForceNode 3.1.637.3.1.4.10.44.4.1.2
This is the routing node ID of the next node in this forced path. It is required for every entry in the Forced Path table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnFrForceFlag 3.1.637.3.1.4.10.44.4.1.3
This flag indicates if this is the preferred or required path. If this flag is set to 'preferred(1)', and the interface designated by adnFrForceOutifindex is not available, then alternate interfaces are tried. If this is set to 'required(2)', and the designated interface is not available, then no additional interfaces are attempted and the call is cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER preferred(1), required(2)  

adnFrForceOutifindex 3.1.637.3.1.4.10.44.4.1.4
This specifies the ifIndex of the interface that the call should use when exiting this node. If adnFrForceFlag has the value 'required(2)', then this interface MUST be used. If adnFrForceFlag is set to 'preferred(1), an alternate interface can be used to get to the next node identified by adnFrForceNode if this interface is unavailable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrFrcNodeMacNum 3.1.637.3.1.4.10.44.4.1.5
The machine number part of the adnFrForceNode, the routing node ID of the next node in this forced path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrFrcNodeAreaNum 3.1.637.3.1.4.10.44.4.1.6
The area number part of the adnFrForceNode, the routing node ID of the next node in this forced path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccountVCTable 3.1.637.3.1.4.10.44.5
This is the Accounting MIB table. These are the counters that are reported in the FRS (Frame Relay Subscriber) accounting record.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrAccountVCEntry

adnFrAccountVCEntry 3.1.637.3.1.4.10.44.5.1
One instance of the FRS (Frame Relay Subscriber) accounting counters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrAccountVCEntry  

adnFrAccountTariff 3.1.637.3.1.4.10.44.5.1.1
This indicates the tariff period for these counters. A tariff period is a designated time period during which specified billing rates apply
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccountInSegments 3.1.637.3.1.4.10.44.5.1.2
This indicates the number of ingress sub-frames in this reporting period for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrAccountOutSegments 3.1.637.3.1.4.10.44.5.1.3
This indicates the number of egress sub-frames in this reporting period for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrAccountInFrames 3.1.637.3.1.4.10.44.5.1.4
This indicates the number of ingress frames in this reporting period for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrAccountOutFrames 3.1.637.3.1.4.10.44.5.1.5
This indicates the number of egress frames in this reporting period for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrAccountInExcessFrames 3.1.637.3.1.4.10.44.5.1.6
This indicates the number of ingress excess frames in this reporting period for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrAccountOutExcessFrames 3.1.637.3.1.4.10.44.5.1.7
This indicates the number of egress excess frames in this reporting period for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrAccVCTable 3.1.637.3.1.4.10.44.6
This table constitutes the FRS (Frame Relay Subscriber) accounting record. None of the objects in this table can be obtained via an SNMP GET command. These objects are visible only in an accounting record. Most of these objects duplicate objects in other tables. They are collected here to allow the accounting record to be sent as a single table to conserve space.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrAccVCEntry

adnFrAccVCEntry 3.1.637.3.1.4.10.44.6.1
One instance of the FRS (Frame Relay Subscriber) accounting record.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrAccVCEntry  

adnFrAccVCifName 3.1.637.3.1.4.10.44.6.1.1
This is a duplicate of ifName for use in the accounting record.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnFrAccVCfrPVCEndptDLCIIndex 3.1.637.3.1.4.10.44.6.1.2
This is a duplicate of frPVCEndptDLCIIndex.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCadnFrVCRemDlci 3.1.637.3.1.4.10.44.6.1.3
This is a duplicate of adnFrVCRemDlci.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCadnFrVCUniqueConnID 3.1.637.3.1.4.10.44.6.1.4
This is a duplicate of adnFrVCUniqueConnID.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCadnFrVCRemNodeID 3.1.637.3.1.4.10.44.6.1.5
This is a duplicate of adnFrVCRemNodeID.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRoutingID  

adnFrAccVCfrLportNumPlan 3.1.637.3.1.4.10.44.6.1.6
This is a duplicate of frLportNumPlan.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), e164(2), x121(3), none(4)  

adnFrAccVCifPhysAddress 3.1.637.3.1.4.10.44.6.1.7
This is a duplicate of ifPhysAddress.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PhysAddress  

adnFrAccVCadnFrVCRemNumPlan 3.1.637.3.1.4.10.44.6.1.8
This is a duplicate of adnFrVCRemNumPlan.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), e164(2), x121(3), none(4)  

adnFrAccVCadnFrVCRemPhysAddress 3.1.637.3.1.4.10.44.6.1.9
This is a duplicate of adnFrVCRemPhysAddress. This object is deprecated in favor of adnFrAccVCSVCCalledPartyNum.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  PhysAddress  

adnFrAccVCadnFrVCSourceDest 3.1.637.3.1.4.10.44.6.1.10
This is a duplicate of adnFrVCSourceDest.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER source(1), destination(2)  


adnFrAccVCfrPVCEndptInCIR 3.1.637.3.1.4.10.44.6.1.12
This is a duplicate of frPVCEndptInCIR.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCadnFrVCInBc 3.1.637.3.1.4.10.44.6.1.13
This is a duplicate of adnFrVCInBc.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCadnFrVCInBcs 3.1.637.3.1.4.10.44.6.1.14
This is a duplicate of adnFrVCInBcs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCfrPVCEndptInBe 3.1.637.3.1.4.10.44.6.1.15
This is a duplicate of frPVCEndptInBe.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCfrPVCEndptOutCIR 3.1.637.3.1.4.10.44.6.1.16
This is a duplicate of frPVCEndptOutCIR.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCadnFrVCOutBc 3.1.637.3.1.4.10.44.6.1.17
This is a duplicate of adnFrVCOutBc.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCadnFrVCOutBcs 3.1.637.3.1.4.10.44.6.1.18
This is a duplicate of adnFrVCOutBcs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCfrPVCEndptOutBe 3.1.637.3.1.4.10.44.6.1.19
This is a duplicate of frPVCEndptOutBe.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCadnFrVCUserOrNet 3.1.637.3.1.4.10.44.6.1.20
This is a duplicate of adnFrVCUserOrNet.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER usercall(1), networkcall(2)  

adnFrAccVCfrAccountPVCSegmentSize 3.1.637.3.1.4.10.44.6.1.21
This is a duplicate of frAccountPVCSegmentSize.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCadnFrVCType 3.1.637.3.1.4.10.44.6.1.22
This is a duplicate of adnFrVCType.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), pvc(2), svc(3), mspvc(4)  

adnFrAccVCTimeEndAcct 3.1.637.3.1.4.10.44.6.1.23
This indicates the time this accounting record was generated for this VC. Since an accounting record has this time and the previous time (adnFrAccVCTimeStartAcct), the NMS can determine the length of time an accounting record spans. The time given in coordinated universal time (UTC).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnFrAccVCTimeStartAcct 3.1.637.3.1.4.10.44.6.1.24
This indicates the time the previous accounting record was sent for this VC. Since an accounting record has this time and the current time (adnFrAccVCTimeEndAcct), the NMS can determine the length of time an accounting record spans. The time is given in coordinated universal time (UTC).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnFrAccVCCallTerm 3.1.637.3.1.4.10.44.6.1.25
This field is placed into the accounting record to indicate if the call has been terminated or not. For a PVC - CallTerminated = PVC has been deleted CallNotTerminated = PVC has not been deleted For a SVC - CallTerminated = call has been cleared CallNotTerminated = call has not been cleared.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER callTerminated(1), callNotTerminated(2)  

adnFrAccVCadnFrChanLineType 3.1.637.3.1.4.10.44.6.1.26
This is a duplicate of adnFrChanLineType.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), fric(2), frad(3), frx(4), ip(5)  

adnFrAccVCadnFrVCNumNodes 3.1.637.3.1.4.10.44.6.1.27
This is a duplicate of adnFrVCNumNodes.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCTableInSegments 3.1.637.3.1.4.10.44.6.1.28
This contains the ingress segment count for this reporting period.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCTableInFrames 3.1.637.3.1.4.10.44.6.1.29
This contains the ingress frame count for this reporting period.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCTableInExcessFrame 3.1.637.3.1.4.10.44.6.1.30
This contains the ingress excess frames count for this reporting period.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCTableOutSegments 3.1.637.3.1.4.10.44.6.1.31
This contains the egress segment count for this reporting period.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCTableOutFrames 3.1.637.3.1.4.10.44.6.1.32
This contains the egress frame count for this reporting period.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCTableOutExcessFrame 3.1.637.3.1.4.10.44.6.1.33
This contains the egress excess frames count for this reporting period.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCPVCRegroomed 3.1.637.3.1.4.10.44.6.1.34
This field indicates if the PVC has been regroomed during the current accounting period. This field is initialized as false(2) and is set to true(1) when the PVC is regroomed. After the accounting period has ended and the accounting record has been collected by the NMS, the field is set to false(2).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TruthValue  

adnFrAccVCSVCCallingPartyNum 3.1.637.3.1.4.10.44.6.1.35
This is the calling party number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PhysAddress  

adnFrAccVCSVCCalledPartyNum 3.1.637.3.1.4.10.44.6.1.36
This is the number of the party called.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PhysAddress  

adnFrAccVCSVCCallEstablished 3.1.637.3.1.4.10.44.6.1.37
This indicates whether a call was established.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TruthValue  

adnFrAccVCSVCQ933ClearingCause 3.1.637.3.1.4.10.44.6.1.38
This is the clearing cause for the SVC
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCSVCQ933ClearingLocation 3.1.637.3.1.4.10.44.6.1.39
This is the clearing location.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCCos 3.1.637.3.1.4.10.44.6.1.40
This indicates the Class of Service (COS) for the VC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrCos  

adnFrAccVCadnFrVCLocalNodeID 3.1.637.3.1.4.10.44.6.1.41
This is the node ID for this VC. It is a duplicate of adnNodeRoutingID in the adnNodeTable. Common Name: Local Node ID
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRoutingID  

adnFrAccVCadnFrVCDescr 3.1.637.3.1.4.10.44.6.1.42
This is a duplicate of adnFrVCDescr for use in the accounting record. Common Name: Description
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnFrAccVCadnFrVCLocalifIndex 3.1.637.3.1.4.10.44.6.1.43
This is ifIndex for the VC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

adnFrAccVCadnFrVCRemoteifIndex 3.1.637.3.1.4.10.44.6.1.44
This is a duplicate of adnFrVCRemoteifindex
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCadnFrVCEndptInDiscards 3.1.637.3.1.4.10.44.6.1.45
This is a duplicate of adnFrVCEndptInDiscards.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrAccVCifSpeed 3.1.637.3.1.4.10.44.6.1.46
This is a duplicate of ifSpeed.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Gauge  

adnFrAccVCadnNodeTime 3.1.637.3.1.4.10.44.6.1.47
This is a duplicate of adnNodeTime. GMT (Greenwich Mean Time) when the accounting records are generated.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnNodeTimeTicks  

adnFrStatVCTable 3.1.637.3.1.4.10.44.7
This table constitutes the FRS (Frame Relay Subscriber) connection-level statistics record. None of the objects in this table can ever be obtained via an SNMP GET command. These objects are only visible in a statistics record. Most of these objects duplicate objects in other tables. They are collected here to allow the statistics record to be sent as a single table to conserve space.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrStatVCEntry

adnFrStatVCEntry 3.1.637.3.1.4.10.44.7.1
One instance of the FRS (Frame Relay Service) connection statistics record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrStatVCEntry  

adnFrStatVCifName 3.1.637.3.1.4.10.44.7.1.1
This is a duplicate of ifName for use in the connection-level statistics record.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnFrStatVCadnFrVCRemoteifindex 3.1.637.3.1.4.10.44.7.1.2
This is a duplicate of adnFrVCRemoteifindex.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCRemDlci 3.1.637.3.1.4.10.44.7.1.3
This is a duplicate of adnFrVCRemDlci.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCUniqueConnID 3.1.637.3.1.4.10.44.7.1.4
This is a duplicate of adnFrVCUniqueConnID.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCRemNodeID 3.1.637.3.1.4.10.44.7.1.5
This is a duplicate of adnFrVCRemNodeID.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRoutingID  

adnFrStatVCfrLportNumPlan 3.1.637.3.1.4.10.44.7.1.6
This is a duplicate of frLportNumPlan.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), e164(2), x121(3), none(4)  

adnFrStatVCifPhysAddress 3.1.637.3.1.4.10.44.7.1.7
This is a duplicate of ifPhysAddress.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PhysAddress  

adnFrStatVCadnFrVCRemNumPlan 3.1.637.3.1.4.10.44.7.1.8
This is a duplicate of adnFrVCRemNumPlan.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), e164(2), x121(3), none(4)  

adnFrStatVCadnFrVCRemPhysAddress 3.1.637.3.1.4.10.44.7.1.9
This is a duplicate of adnFrVCRemPhysAddress.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PhysAddress  

adnFrStatVCadnFrVCSourceDest 3.1.637.3.1.4.10.44.7.1.10
This is a duplicate of adnFrVCSourceDest.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER source(1), destination(2)  


adnFrStatVCfrPVCEndptInCIR 3.1.637.3.1.4.10.44.7.1.12
This is a duplicate of frPVCEndptInCIR.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCInBc 3.1.637.3.1.4.10.44.7.1.13
This is a duplicate of adnFrVCInBc.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCInBcs 3.1.637.3.1.4.10.44.7.1.14
This is a duplicate of adnFrVCInBcs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCfrPVCEndptInBe 3.1.637.3.1.4.10.44.7.1.15
This is a duplicate of frPVCEndptInBe.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCfrPVCEndptOutCIR 3.1.637.3.1.4.10.44.7.1.16
This is a duplicate of frPVCEndptOutCIR.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCOutBc 3.1.637.3.1.4.10.44.7.1.17
This is a duplicate of adnFrVCOutBc.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCOutBcs 3.1.637.3.1.4.10.44.7.1.18
This is a duplicate of adnFrVCOutBcs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCfrPVCEndptOutBe 3.1.637.3.1.4.10.44.7.1.19
This is a duplicate of frPVCEndptOutBe.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCISR 3.1.637.3.1.4.10.44.7.1.20
This is a duplicate of adnFrVCISR.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCUserOrNet 3.1.637.3.1.4.10.44.7.1.21
This is a duplicate of adnFrVCUserOrNet.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER usercall(1), networkcall(2)  

adnFrStatVCfrAccountPVCSegmentSize 3.1.637.3.1.4.10.44.7.1.22
This is a duplicate of frAccountPVCSegmentSize.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCType 3.1.637.3.1.4.10.44.7.1.23
This is a duplicate of adnFrVCType.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), pvc(2), svc(3), mspvc(4)  

adnFrStatVCadnNodeTime 3.1.637.3.1.4.10.44.7.1.24
This is a duplicate of adnNodeTime.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnNodeTimeTicks  

adnFrStatVCadnFrVCAdminState 3.1.637.3.1.4.10.44.7.1.25
This is a duplicate of adnFrVCAdminState.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnFrStatVCadnFrVCOperState 3.1.637.3.1.4.10.44.7.1.26
This is a duplicate of adnFrVCOperState.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnFrStatVCadnFrVCFrameIN 3.1.637.3.1.4.10.44.7.1.27
This is a duplicate of adnFrVCFrameIN.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCFrameOUT 3.1.637.3.1.4.10.44.7.1.28
This is a duplicate of adnFrVCFrameOUT.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCSubFrameIN 3.1.637.3.1.4.10.44.7.1.29
This is a duplicate of adnFrVCSubFrameIN.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCSubFrameOUT 3.1.637.3.1.4.10.44.7.1.30
This is a duplicate of adnFrVCSubFrameOUT.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCBeInDiscards 3.1.637.3.1.4.10.44.7.1.31
This is a duplicate of adnFrVCBeInDiscards.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCBcsInDiscards 3.1.637.3.1.4.10.44.7.1.32
This is a duplicate of adnFrVCBcsInDiscards.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCBcInDiscards 3.1.637.3.1.4.10.44.7.1.33
This is a duplicate of adnFrVCBcInDiscards.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCBeOutDiscards 3.1.637.3.1.4.10.44.7.1.34
This is a duplicate of adnFrVCBeOutDiscards.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCBcsOutDiscards 3.1.637.3.1.4.10.44.7.1.35
This is a duplicate of adnFrVCBcsOutDiscards.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCBcOutDiscards 3.1.637.3.1.4.10.44.7.1.36
This is a duplicate of adnFrVCBcOutDiscards.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCDiscardLisIn 3.1.637.3.1.4.10.44.7.1.37
This is a duplicate of adnFrVCDiscardLisIn.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCInCongsState 3.1.637.3.1.4.10.44.7.1.38
This is a duplicate of adnFrVCInCongsState.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnCongestLevels  

adnFrStatVCfrPVCEndptDLCIIndex 3.1.637.3.1.4.10.44.7.1.39
This is a duplicate of frPVCEndptDLCIIndex.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCNumNodes 3.1.637.3.1.4.10.44.7.1.40
This is a duplicate of adnFrVCNumNodes.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCfrPVCEndptInOctets 3.1.637.3.1.4.10.44.7.1.41
This is a duplicate of frPVCEndPtInOCtets
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCfrPVCEndptOutOctets 3.1.637.3.1.4.10.44.7.1.42
This is a duplicate of frPVCEndPtOutOctets
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrStatVCadnFrVCDescr 3.1.637.3.1.4.10.44.7.1.43
This is a duplicate of adnFrVCDescr.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnFrReachAddrTable 3.1.637.3.1.4.10.44.8
This table contains the list of complete addresses and/or address prefixes configured for this access interface (port/channel) if the Multiple Subscriber Number (MSN) service is used.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrReachAddrEntry

adnFrReachAddrEntry 3.1.637.3.1.4.10.44.8.1
An entry in the adnFrReachAddrTable. There is one entry for each element of the list.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrReachAddrEntry  

adnFrReachAddrIndex 3.1.637.3.1.4.10.44.8.1.1
The index of an element in the list.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnFrReachAddrNumPlan 3.1.637.3.1.4.10.44.8.1.2
The numbering plan of the complete address or address prefix specified in adnFrReachAddrNumber. Common Names: Numbering Plan, Num Plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), e164(2), x121(3), none(4)  

adnFrReachAddrNumberLength 3.1.637.3.1.4.10.44.8.1.3
The number of digits of the prefix address specified in adnFrReachAddrNumber.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFrReachAddrNumber 3.1.637.3.1.4.10.44.8.1.4
The complete address or address prefix of a location reachable through this access interface (port/channel).
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

adnFrCosTable 3.1.637.3.1.4.10.44.9
This table contains the Class Of Service (COS) information at the channel level for FRS (Frame Relay Service).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrCosEntry

adnFrCosEntry 3.1.637.3.1.4.10.44.9.1
An entry in the table. There will be one entry for each FRS (Frame Relay Service) channel configured.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrCosEntry  

adnFrCosIndex 3.1.637.3.1.4.10.44.9.1.1
The Cos (Class Of Service) index for a specific class of service managed by this frame relay interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnFrCos  

adnFrCosAdminStatus 3.1.637.3.1.4.10.44.9.1.2
This object provides a mechanism for controlling the status of Class of Service (COS). Set to 'locked(2)' it will cause any new calls to this Class of Service be rejected. Set to 'unlocked(1)' it will cause resumption of the normal operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnFrCosAdminStatus  

adnFrCosOperStatus 3.1.637.3.1.4.10.44.9.1.3
This object indicates the operational status of Class of Service (COS). A value of 'locked(2)' indicates that any new calls will be rejected for this Class of Service (COS). A value of 'unlocked(1)' indicates normal operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnFrCosOperStatus  

adnIfMIBObjects 3.1.637.3.1.4.31.1
OBJECT IDENTIFIER    

adnIfTestType 3.1.637.3.1.4.31.3
OBJECT IDENTIFIER    

adnIfTestTypeOther 3.1.637.3.1.4.31.3.1
OBJECT IDENTIFIER    

adnIfTestTypeNone 3.1.637.3.1.4.31.3.2
OBJECT IDENTIFIER    

adnIfTestTypeData 3.1.637.3.1.4.31.3.3
OBJECT IDENTIFIER    

adnIfTestTypeManualV54 3.1.637.3.1.4.31.3.4
OBJECT IDENTIFIER    

adnIfTestTypeRemoteV54 3.1.637.3.1.4.31.3.5
OBJECT IDENTIFIER    

adnIfTestTypeLocalV54 3.1.637.3.1.4.31.3.6
OBJECT IDENTIFIER    

adnIfTestTypeApplique 3.1.637.3.1.4.31.3.7
OBJECT IDENTIFIER    

adnIfTestTypePriApplBus 3.1.637.3.1.4.31.3.8
OBJECT IDENTIFIER    

adnIfTestTypeRedApplBus 3.1.637.3.1.4.31.3.9
OBJECT IDENTIFIER    

adnIfTestTypeIntCoupler 3.1.637.3.1.4.31.3.10
OBJECT IDENTIFIER    

adnIfTestTypeLineLoop 3.1.637.3.1.4.31.3.11
OBJECT IDENTIFIER    

adnIfTestTypePayloadLoop 3.1.637.3.1.4.31.3.12
OBJECT IDENTIFIER    

adnIfTestTypeLineHW 3.1.637.3.1.4.31.3.13
OBJECT IDENTIFIER    

adnIfTestTable 3.1.637.3.1.4.31.1.3
The ADN Interface Test Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIfTestEntry

adnIfTestEntry 3.1.637.3.1.4.31.1.3.1
Loop test control and results values for an interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIfTestEntry  

adnIfTestTimeLimit 3.1.637.3.1.4.31.1.3.1.1
The time, in hundredths of a second, that the test will run before automatically being terminated. Common name: Time Limit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIfTestFailLevel 3.1.637.3.1.4.31.1.3.1.2
Threshold for the allowable bit error rate, expressed as one in ten-to-the-power-X, where X is the value of this parameter. For example, the default value of six means that a bit error rate of more than 1 in 1,000,000 is considered failure. This parameter is only used when the HSS sets ifTestResult to success or failed at the end of a test. Common name: Fail Level
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIfTestBitsSentHi 3.1.637.3.1.4.31.1.3.1.3
The most significant 32 bits of the 64-bit internal counter of the number of test bits sent. See also adnIfTestBitsSentLo. Common name: Test Bits Sent High #
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnIfTestBitsSentLo 3.1.637.3.1.4.31.1.3.1.4
The least significant 32 bits of the 64-bit internal counter of the number of test bits sent. See also adnIfTestBitsSentHi. Common name: Test Bits Sent Low #
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnIfTestBitsReceivedHi 3.1.637.3.1.4.31.1.3.1.5
The most significant 32 bits of the 64-bit internal counter of the number of test bits received. See also adnIfTestBitsReceivedLo. Common name: Test Bits Received High #
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnIfTestBitsReceivedLo 3.1.637.3.1.4.31.1.3.1.6
The least significant 32 bits of the 64-bit internal counter of the number of test bits received. See also adnIfTestBitsReceivedHi. Common name: Test Bits Received Low #
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnIfTestBitsErroredHi 3.1.637.3.1.4.31.1.3.1.7
The most significant 32 bits of the 64-bit internal counter of the number of test bits received that did not match the bits that were sent (i.e., number of bits in error). See also adnIfTestBitsErroredLo. Common name: Test Bits Errored High #
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnIfTestBitsErroredLo 3.1.637.3.1.4.31.1.3.1.8
The least significant 32 bits of the 64-bit internal counter of the number of test bits received that did not match the bits that were sent (i.e., number of bits in error). See also adnIfTestBitsErroredHi. Common name: Test Bits Errored Low #
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnIfTestStartTime 3.1.637.3.1.4.31.1.3.1.9
The value of sysUpTime, in hundredths of a second, when the test started. Common name: Start Time
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeStamp  

adnIfTestStopTime 3.1.637.3.1.4.31.1.3.1.10
The value of sysUpTime, in hundredths of a second, when the test stopped, or the current time if a test is in progress. Common name: Stop Time
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeStamp  

adnInterfaces 3.1.637.3.1.4.2
OBJECT IDENTIFIER    

adnIfTable 3.1.637.3.1.4.2.2
A list of interface entries. The number of entries is given by the value of ifNumber.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIfEntry

adnIfEntry 3.1.637.3.1.4.2.2.1
An interface entry containing objects at the subnetwork layer and below for a particular interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIfEntry  

adnIfInstallStatus 3.1.637.3.1.4.2.2.1.1
The value of this object provides additional information concerning the availability status of the interface. It is a bitmap of installation status conditions. When the value of this object is 0, none of the status conditions are present. 1 - initialization incomplete 2 - last restart operator initiated 4 - reserved for test
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnIfControlStatus 3.1.637.3.1.4.2.2.1.2
This object provides a mechanism for controlling the status of the interface. Its value is a bitmap of controls that determine the value of ifAdminStatus. A value of 0 indicates that none of the status controls are in effect. 1 - reset 2 - reserve for test 4 - shutting down
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnIfSubType 3.1.637.3.1.4.2.2.1.3
This object provides additional type information for interfaces with an ifType of 'other' or 'proprietary virtual'. 1 - No qualification 2 - other, FRANP (Frame Relay Alcatel Network Protocol) 3 - other, ISS (Internal Subscriber Service) 100 - proprietary virtual, FLIP (Fake Line Interface Process) 101 - proprietary virtual, ATM internal line 102 - proprietary virtual, ATM logical line (internode virtual path) 103 - proprietary virtual, frame relay logical line (interworking virtual channel connection) 104 - proprietary virtual, IP over frame relay logical line (interworking FR virtual connection) 105 - proprietary virtual, IP over ATM logical line (interworking virtual channel connection)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noqual(1), franp(2), iss(3), frFlip(100), atmInternal(101), atmLogical(102), frLogical(103), ipOverFr(104), ipOverAal5(105)  

adnEquipTable 3.1.637.3.1.5.1
A list of equipment entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnEquipEntry

adnEquipEntry 3.1.637.3.1.5.1.1
An equipment entry containing objects that represent the state of hardware, firmware, or software components. Currently only hardware components are modelled.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnEquipEntry  

adnEquipType 3.1.637.3.1.5.1.1.1
The type of component this entry represents. 1 - other 5 - chassis 2 - node 6 - processor 3 - card 7 - iosPort 4 - interface 8 - aeiPort
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEquipType  

adnEquipIndex 3.1.637.3.1.5.1.1.2
The index of the component this entry represents.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnEquipSubType 3.1.637.3.1.5.1.1.3
A more specific indication of the type of component this entry represents. For example, when adnEquipType is 'card' adnEquipSubType might be 'adnHbcp8'. If this information is not present, its value is set to the OBJECT IDENTIFIER { 0 0 }. Common name: Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  AutonomousType  

adnEquipLastChange 3.1.637.3.1.5.1.1.4
The value of sysUpTime at the time the component entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value. Common name: Last Change Time
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeStamp  

adnEquipInitTime 3.1.637.3.1.5.1.1.5
The time the component initialized with respect to the initialization of the local network management subsystem measured in hundredths of a second. It is the value of sysUpTime at the time the component entered the 'enabled' operational state. If the component initialized prior to the agent's most recent initialization, this object contains a zero value. Common name: Up Since
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeStamp  

adnEquipTrapEnableMask 3.1.637.3.1.5.1.1.6
The value of this object is a bitmap that indicates which states and statuses should cause an adnEquipStatusChange trap to be sent. bit value state/status object (common state name) ------------ ------------------- ------------------- 1 adnEquipX731Oper (operational) 2 adnEquipX731Admin (administrative) 4 adnEquipX731Usage (usage) 8 adnEquipX731Avail (availability) 16 adnEquipInstallStatus (install) 32 adnEquipControlStatus (control) Common name: Trap Enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnEquipX731Oper 3.1.637.3.1.5.1.1.7
The value of this object represents the operational state of this component. Common name: Operational
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

adnEquipX731Admin 3.1.637.3.1.5.1.1.8
The value of this object represents the administrative state of this component. Common name: Administrative
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unlocked(1), locked(2), shuttingDown(3)  

adnEquipX731Usage 3.1.637.3.1.5.1.1.9
The value of this object represents the usage state of this component. Common name: Usage
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(0), idle(1), active(2), busy(3)  

adnEquipX731Avail 3.1.637.3.1.5.1.1.10
The value of this object is a bitmap that qualifies the value of the operational and administrative states. When the value of this object is 0, none of the status conditions are present. bit value resource condition ----- ------------------ 1 inTest - undergoing a test procedure 2 failed - has an internal fault preventing its operation 4 powerOff - requires power, but is not powered on 8 offLine - requires a routine operation to put it online 16 offDuty - is inactive by an internal control process 32 dependency - cannot operate because it depends on an unavailable resource 64 degraded - service provided is degraded (speed, capacity, or etc.) 128 notInstalled - not present or incomplete 256 logFull - for a log only, indicates that it is full Common name: Availability
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnEquipInstallStatus 3.1.637.3.1.5.1.1.11
The value of this object provides additional information concerning the availability status (adnEquipX731Avail) of the equipment. It is a bitmap of installation status conditions. When the value of this object is 0, none of the status conditions are present. bit value meaning qualifies ------------ --------------------------- -------------- 1 absent 'notInstalled' 2 notConfigured 'notInstalled' 4 initializationIncomplete 'offLine' 128 incorrectConfiguration 'failed' The following bit positions are deprecated: bit value meaning qualifies ------------ --------------------------- -------------- 8 operatorInitiatedLastRestart any setting 16 initializationRequired 'offLine' 32 reservedForTest 'inTest' 64 testInitiated 'inTest'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnEquipControlStatus 3.1.637.3.1.5.1.1.12
This object provides a mechanism for controlling the status of the equipment. Its value is a bitmap of controls that determine the value of adnEquipX731Admin. A value of 0 indicates that none of the status controls are in effect. bit value meaning ----- -------------------------------------------- 1 suspend - put card (except control unit (CU)) in permanent reset 2 coldRestart - restart equipment, interrupting service - node and card (except CU) on HSS; node, card and interface on TPX 4 mildRestart - restart equipment, and do not interrupt service - only for active or standby CU card 32 initiateTest - begin test - standby CU card only 64 manualSwitchover - switch to backup - primary MSC, CIG, and BBASE cards and active CU cards only 128 manualSwitchback - switch to primary - primary MSC, CIG, and BBASE cards only 256 osRebuild - all firmware and disk contents are copied fromthe active CU card - standby CU card only The following bit values are deprecated: value meaning ------ -------------------------------------------- 8 debugModeAfterCrash (do not reload operational code after crash and allow viewing of card's data structures) 16 reserveForTest
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnEquipControlHistory 3.1.637.3.1.5.1.1.13
The adnEquipControlHistory object is a bitmap that provides information about the cause of the last restart, switchover to spare and switchback to primary. It may be cleared by setting it to 0; no other SNMP Set operations are allowed. bit val meaning --- ------------------------------------------------------- 1 restartDueToUpdate last restart due to code or configuration update 2 restartFromOperator operator initiated last restart 4 restartDueToFailure last restart was caused by a board or node failure 8 restartDueToNode last restart caused by a node level restart; if not set, restart was at the board level 16 switchoverFromOperator operator initiated last switchover 32 switchbackFromOperator operator initiated last switchback
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnEquipControlOptions 3.1.637.3.1.5.1.1.14
The adnEquipControlOptions object provides a mechanism for controlling future reactions of the equipment. It is a bitmap of options; a value of 0 indicates that no options are in effect. bit value meaning ----- ----------------------------------------------------- 1 debugAfterCrash - place in debug mode after crash; do not reload operational code after crash. For instance, only allow viewing of a card's data structures)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnEquipSwitchoverOptions 3.1.637.3.1.5.1.1.15
The adnEquipSwitchoverOptions object provides the options in effect for the next switchover to spare. It is only significant for primary equipment; its value is 'noSwitch' for spares and equipment that does not support redundancy. other : not used noSwitch : used for spares and equipment that do not support redundancy coldManual : used for primary MSC, CIG and BBASE card coldAutomatic : used for primary MSC, CIG and BBASE card warmAutomatic : used for Control Unit and BBSYN card. The switchover is cold when the software is not already loaded onto the card; it is the case for MSC coupler, CIG and BBASE card. Otherwise, the switchover is warm. With the manual option, the switchover is performed only on operator request. With the automatic option, the switchover is performed on HSS supervision software request when a card is failed or on operator request.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), noSwitch(2), coldManual(3), coldAutomatic(4), warmAutomatic(5)  

adnEquipTrapCause 3.1.637.3.1.5.1.1.16
adnEquipTrapCause contains the value of the adnEquipCause field in the last trap generated by the equipment. It indicates the specific cause of the problem that appeared on the equipment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEquipCause  

adnEquipX731StandbyStatus 3.1.637.3.1.5.1.1.17
The adnEquipX731StandbyStatus object describes the role of spare equipment. In particular, it indicates whether the equipment is in a standby mode or acting for another piece of equipment. coldStandby means that the equipment is not synchronized with the primary equipment; it requires initialization before it can take over the role of the primary equipment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(1), coldStandby(2), providingService(3)  

adnEquipSwitchbackOptions 3.1.637.3.1.5.1.1.18
The adnEquipSwitchbackOptions object provides the options in effect for the next switchback to primary. It is only significant for primary equipment and if the adnEquipSwitchoverOptions object is different from 'noSwitch'. other : used for configuration purpose when adnEquipSwitchoverOptions value is 'noSwitch', also used for Control Unit and BBSYN card. coldManual : used for primary MSC, CIG and BBASE card. coldSemiautomatic : used for primary MSC, CIG and BBASE card. The switchback is cold when the software is not already loaded onto the card; it is the case for MSC coupler, CIG and BBASE card. With the manual option, the switchback is performed only on operator request. With the semi-automatic option, the switchover is performed on HSS supervision software request when the spare card is failed, or on operator request.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), coldManual(2), coldSemiautomatic(3)  

adnContainTable 3.1.637.3.1.5.2
A list of container entries. For example, a node contains chassis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnContainEntry

adnContainEntry 3.1.637.3.1.5.2.1
A container entry representing the containment relationship between entries in the equipment table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnContainEntry  

adnContainerType 3.1.637.3.1.5.2.1.1
This object corresponds to the adnEquipType of the container component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEquipType  

adnContainerIndex 3.1.637.3.1.5.2.1.2
The value of this object corresponds to the adnEquipIndex of the container component. Common name: Equip Index
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnContainedType 3.1.637.3.1.5.2.1.3
The value of this object corresponds to the adnEquipType of the contained component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEquipType  

adnContainedIndex 3.1.637.3.1.5.2.1.4
The value of this object corresponds to the adnEquipIndex of the contained component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnContainerPosition 3.1.637.3.1.5.2.1.5
The value of this object represents the position of the contained component within the container component.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnNodeTable 3.1.637.3.1.5.3
A list of node entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnNodeEntry

adnNodeEntry 3.1.637.3.1.5.3.1
An entry that augments a equipment entry for a node. This table is based on the system table of MIB-II.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnNodeEntry  

adnNodeIndex 3.1.637.3.1.5.3.1.1
A unique value for each node in the agent's domain. This object corresponds to the adnEquipIndex in the equipment table. Release 2.0 and 2.1 only have one entry in the node table, but multiple entries may be present for the regional CU (control unit) environment. Common name: Node Index
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnNodeDescr 3.1.637.3.1.5.3.1.2
A textual description of the entity. This value should include the full name and version identification of the node's hardware type, software operating system, and networking software. The value may only contain printable ASCII characters. Common names: Node Description, Description
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnNodeContact 3.1.637.3.1.5.3.1.3
The textual identification of the contact person for this managed node, and information on how to contact the person. Common name: Contact
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnNodeName 3.1.637.3.1.5.3.1.4
An administratively assigned name for this managed node. By convention, this is the node's fully qualified domain name. Common name: Name
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnNodeLocation 3.1.637.3.1.5.3.1.5
The physical location of this node (for example, `telephone closet, 3rd floor'). This information helps a service technician find the node. Common name: Location
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnNodeServices 3.1.637.3.1.5.3.1.6
A value which indicates the set of services that this entity primarily offers. The value is a bitmask where each bit indicates whether the entity supports the services at the corresponding protocol stack layer. In the context of the Internet suite of protocols, values should be calculated accordingly: bit layer functionality --- ----- ------------- 1 1 physical (e.g., repeaters) 2 2 datalink/subnetwork (e.g., bridges) 4 3 internet (e.g., IP gateways) 8 4 end-to-end (e.g., IP hosts) 64 7 applications (e.g., mail relays) For systems including OSI protocols, layers 5 and 6 have the values 16 and 32, respectively. For example, a node which performs primarily routing functions would have a value of 4. In contrast, a node which is an IP host offering application services would have a value of 72 (72 = 8 + 64). Common name: Services
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnNodeNumPlan 3.1.637.3.1.5.3.1.7
The value of this object identifies the network numbering plan used for the node's management port. Common name: Network Plan
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), x121(2), e164(3), ip(4)  

adnNodeAddress 3.1.637.3.1.5.3.1.8
The value of this object identifies the network address of the node's management port. Common name: IP Address
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

adnNodeClockRefresh 3.1.637.3.1.5.3.1.9
This field indicates the period (in minutes) for resynchronizing the clock between CU (Control Unit) and OM (Operations and Maintenance) processors. Common name: Clock Refresh
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnNodeRoutingID 3.1.637.3.1.5.3.1.10
This field identifies the node for CANP (Cell Alcatel Network Protocol) and FRANP (Frame Relay Alcatel Network Protocol) signalling. It is also used by path select, routing, and FRS (Frame Relay Service) code.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnNodeMaxChassis 3.1.637.3.1.5.3.1.11
This field indicates the maximum number of chassis that may be configured in this node. That is, this is the maximum value of the chassis number. The value of this nominator depends upon the HSS model.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnNodeMachineNumber 3.1.637.3.1.5.3.1.12
The node number inside the area.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnNodeAreaNumber 3.1.637.3.1.5.3.1.13
The area number of the node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnNodeNetworkType 3.1.637.3.1.5.3.1.14
This field indicates the type of the network. It is the same for all nodes inside a same network. This object is used by ATM signalling to fill in the location field of the CAUSE Information Element in the release messages. This object could be used by Frame Relay signalling as well.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), public(2), private(3)  

adnNodeAtmNetPloss 3.1.637.3.1.5.3.1.15
This value is used for ATM networks. It is the same for all nodes inside a same network. This value represents the probability of cell loss specified by the operator. It is used by ATM traffic management for non real time Variable Bit Rate (VBR) connections. The stored value is the positive value of the decimal logarithm of this probability. For example : 5 means that the probability is '10 to the power of -5'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnNodeConfigFrom 3.1.637.3.1.5.3.1.16
This value is used to indicate the origin of the configuration. In case of configuration from HIT (HSS Installation Tool) some checks are suppressed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER nms(1), hit(2)  

adnCongMgmtMIB 3.1.637.3.1.5.5
OBJECT IDENTIFIER    

adnCongMgmtChanTable 3.1.637.3.1.5.5.1
Frame relay channel information table for congestion management.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCongMgmtChanEntry

adnCongMgmtChanEntry 3.1.637.3.1.5.5.1.1
An entry in the frame relay channel information table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnCongMgmtChanEntry  

adnCongMgmtChanCUFValue 3.1.637.3.1.5.5.1.1.1
Equals the current CUF (channel utilization factor) value of the channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCongMgmtVCTable 3.1.637.3.1.5.5.2
VC table for frame relay congestion management.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCongMgmtVCEntry

adnCongMgmtVCEntry 3.1.637.3.1.5.5.2.1
VC table entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnCongMgmtVCEntry  

adnCongMgmtVCDLCIIndex 3.1.637.3.1.5.5.2.1.1
Equal to the DLCI (data link connection identifier) value for the frame relay trunk or FRS (frame relay subsystem) local DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCongMgmtVCBcInDiscards 3.1.637.3.1.5.5.2.1.2
Number of Bc (committed data rate) sub-frames that were discarded for ingress traffic (TPX interworking function, frame relay switching interface, or frame relay subsystem) due to ISM (internal switching mechanism) queue congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCongMgmtVCBcsInDiscards 3.1.637.3.1.5.5.2.1.3
Number of Bcs (statistically committed data rate) sub-frames that were discarded for ingress traffic (TPX interworking function, frame relay switching interface, or frame relay subsystem) due to ISM (internal switching mechanism) queue congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCongMgmtVCBeInDiscards 3.1.637.3.1.5.5.2.1.4
Number of Be (excess burst data rate) sub-frames that were discarded for ingress traffic (TPX interworking function, frame relay switching interface, or frame relay subsystem) due to ISM (internal switching mechanism) queue congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCongMgmtVCInBcSubfrmSent 3.1.637.3.1.5.5.2.1.5
Number of Bc (committed data rate) sub-frames sent to the ISM (internal switching mechanism).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCongMgmtVCInBcsSubfrmSent 3.1.637.3.1.5.5.2.1.6
Number of Bcs (statistically committed data rate) sub-frames sent to the ISM (internal switching mechanism).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCongMgmtVCInBeSubfrmSent 3.1.637.3.1.5.5.2.1.7
Number of Be (excess burst data rate) sub-frames sent to the ISM (internal switching mechanism).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnCongMgmtVCInCongsState 3.1.637.3.1.5.5.2.1.8
Congestion level in the direction of transmit to ISM (internal switching mechanism).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnCongestLevels  

adnCongMgmtVCCurrentSIR 3.1.637.3.1.5.5.2.1.9
Equals the current submission rate of this VC, if this VC belongs to the FRS (frame relay subsystem) channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsnaMIB 3.1.637.3.1.5.6
OBJECT IDENTIFIER    

adnIsnaIcTable 3.1.637.3.1.5.6.1
This is the internal connection table identifying connections mapped within the internal subscriber node administrator (ISNA) and internal subscriber operation & maintenance (ISOM) software component. These connections are mapped one-for-one to frame relay DLCIs defined within the frame relay service software component.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIsnaIcEntry

adnIsnaIcEntry 3.1.637.3.1.5.6.1.1
Internal connection for internal subscriber subsystem (ISS) table entry. The adnIsnaIcifIndex and adnIsnaIcDlci used in this table have the same values as the ones used in the isom.mib file table adnIsomVcTable. Maintaining the same values for these objects as in the adnIsomVcTable provides the definition for a given ISS internal connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIsnaIcEntry  

adnIsnaIcifIndex 3.1.637.3.1.5.6.1.1.1
This object defines the first half of an internal subscriber subsystem internal connection (IC) referenced by an internal fake line ifIndex. This internal fake line ifIndex is mapped over common memory between the internal subscriber on the operation and maintenance processor and the frame relay service subsystem on the line termination processor. The value of this object is the same one used in a corresponding IC entry called adnIsomVcifIndex in the adnIsomVcTable table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsnaIcDlci 3.1.637.3.1.5.6.1.1.2
This object defines the second half of an internal subscriber subsystem internal connection (IC) referenced by an internal fake line DLCI. This internal fake line DLCI is mapped over common memory between the internal subscriber on the operation and maintenance processor and the frame relay service subsystem on the line termination processor. The value of this object is the same one used in a corresponding IC entry called adnIsomVcoutDlci in the adnIsomVcTable table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsnaIcType 3.1.637.3.1.5.6.1.1.3
This object indicates whether this internal connection will act as the primary or backup internal connection for another internal connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER primary(1), backup(2)  

adnIsnaIcBckIfindex 3.1.637.3.1.5.6.1.1.4
This object represents the backup internal connection ifIndex for a given internal connection defined between internal subscriber node administrator and internal subscriber operation and maintenance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsnaIcBckDlci 3.1.637.3.1.5.6.1.1.5
This object represents the backup internal connection data link connection identifier for a given internal connection defined between internal subscriber node administrator and internal subscriber operation maintenance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsnaIcAdminState 3.1.637.3.1.5.6.1.1.6
This object contains the desired state of the internal subscriber subsystem internal connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnIsnaIcOperState 3.1.637.3.1.5.6.1.1.7
This object contains the current state of the ISS internal connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnIsnaRouteIpTable 3.1.637.3.1.5.6.2
This is the routing table used by internal subscriber node administrator to determine to which internal connection to route a packet received from the local IP layer. The routing decision is made based on the destination IP address found in the IP packet.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIsnaRouteIpEntry

adnIsnaRouteIpEntry 3.1.637.3.1.5.6.2.1
This field describes IP routes for each entry in the adnIsnaRouteIpTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIsnaRouteIpEntry  

adnIsnaRouteifIndex 3.1.637.3.1.5.6.2.1.1
This object is mapped to adnIsnaIcifIndex in the adnIsnaIcTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsnaRouteDlci 3.1.637.3.1.5.6.2.1.2
This object is mapped to adnIsnaIcDlci in the adnIsnaIcTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsnaRouteIpAddrs 3.1.637.3.1.5.6.2.1.3
Defines the IP address of any host that needs to communicate with the HSS for network management purposes. This field is used internally by the internal subscriber subsystem to link IP addresses to internal subscriber subsystem data link connection identifiers (DLCI). At a minimum, the IP address of the A1100 NMS must be entered. Any other hosts using applications that would access the HSS need their IP address entered here.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

adnIsnaRouteIpMask 3.1.637.3.1.5.6.2.1.4
Defines which bits of the IP address are examined in reading the IP address of any host that needs to communicate with the HSS. Bit fields in the mask that are set to '1' cause the address digit to be significant, bit fields that are set to '0' cause the digit to be ignored.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

adnIsomMIB 3.1.637.3.1.5.7
OBJECT IDENTIFIER    

adnIsomVcTable 3.1.637.3.1.5.7.2
VC table extensions that serve as alternates to the PVC end-point table in RFC1604, which is not sufficient for the HSS network. Additionally, the Network Management System needs to know the identity of the owner of a given ADN proprietary interface and this is done by utilizing object adnIfSubType=iss of adnIfTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIsomVcEntry

adnIsomVcEntry 3.1.637.3.1.5.7.2.1
VC table entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIsomVcEntry  

adnIsomVcifIndex 3.1.637.3.1.5.7.2.1.1
This is the ifIndex of the internal subscriber line carrying this internal connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsomVcOutDlci 3.1.637.3.1.5.7.2.1.2
DLCI (Data Link Connection Identifier) for this internal connection in the direction from the internal subscriber on the OM (operations and maintenance) processor towards the FRS (frame relay service) subsystem on the LT (line termination) processor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsomVcAdminState 3.1.637.3.1.5.7.2.1.3
Defines the desired state of this internal subscriber connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnIsomVcOperState 3.1.637.3.1.5.7.2.1.4
Defines the current state of this internal subscriber connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnIsomVcTime 3.1.637.3.1.5.7.2.1.5
Defines the time this internal subscriber connection was initialized.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnIsomTrapIpTable 3.1.637.3.1.5.7.3
This table contains a list of Network Management System IP (internet protocol) addresses to which an adnHSSCuDownTrap should be sent in the event that the internal subscriber subsystem detects that the CU (control unit) has gone down. The addresses in this table must match the entries in the CU relating to recipients of the adnNodeResync trap.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIsomTrapIpEntry

adnIsomTrapIpEntry 3.1.637.3.1.5.7.3.1
One or several IP host address entries mapped to a single DLCI as referenced by ifIndex, adnIsomVcOutDlci, and adnIsomTrapIpAddrs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIsomTrapIpEntry  

adnIsomTrapifIndex 3.1.637.3.1.5.7.3.1.1
This object is mapped to 'adnIsomVcifIndex' of 'adnIsomVcTable' table, and is defined similar to the 'adnIsomVcifIndex' entry contained in the adnIsomVcTable table. Used to address the DLCI that carries SNMP CU down traps to a defined NMS host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsomTrapDlci 3.1.637.3.1.5.7.3.1.2
Mapped to 'adnIsomVcOutDlci' of 'adnIsomVcTable' table, and is defined similar to 'adnIsomVcOutDlci' entry contained in the adnIsomVcTable table. Used to address the DLCI that carries SNMP CU down traps to a defined (IP host) NMS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIsomTrapIpAddrs 3.1.637.3.1.5.7.3.1.3
Full 4-byte NMS IP address that the Internal Subscriber Operation and maintenance subsystem uses to send a SNMP CU down trap in the event the node supervision subsystem reports a CU down condition.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

adnRoutesMIB 3.1.637.3.1.5.8
OBJECT IDENTIFIER    

adnRtsCritHopNulNul 3.1.637.3.1.10.1
OBJECT IDENTIFIER    

adnRtsCritDlyMnyHop 3.1.637.3.1.10.2
OBJECT IDENTIFIER    

adnRtsCritMnyDlyHop 3.1.637.3.1.10.3
OBJECT IDENTIFIER    

adnCalcMonTable 3.1.637.3.1.5.8.1
General parameters used by the routing services for node-to-path table calculation.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCalcMonEntry

adnCalcMonEntry 3.1.637.3.1.5.8.1.1
Each entry (row) of the adnCalcMonTable provides the general parameters used by ' the routing services for node-to-path table calculation for a specific type of service and criterion.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnCalcMonEntry  

adntosIndex 3.1.637.3.1.5.8.1.1.1
Type of service: frame relay, ATM virtual channel, ATM virtual path, etc.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), fr(2), atmVc(3), atmVp(4)  

adncriterionIndex 3.1.637.3.1.5.8.1.1.2
Rule used to generate a routing table based on the link cost metrics.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), hop(2), delay(3)  

adnMaxPath 3.1.637.3.1.5.8.1.1.3
Maximum number of paths per node in the node-to-path routing table for a specific type of service and criterion.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnMaxCost 3.1.637.3.1.5.8.1.1.4
Maximum cost of a path to an arbitrary destination node for a type of service and criterion. If the criterion is the number of hops, maximum number of hops. The default value is defined for a criterion equal to the number of hops.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnMinTimeBetCalc 3.1.637.3.1.5.8.1.1.5
Minimum time between successive route calculations for a specific type of service and criterion and identifies the minimum time between completion of routing services initialization and the first routing calculation.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnMessMonTable 3.1.637.3.1.5.8.2
General parameters used by the routing services for routing message handling.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnMessMonEntry

adnMessMonEntry 3.1.637.3.1.5.8.2.1
Each entry (row) of the adnMessMonTable provides the general parameters used by the routing services for routing message handling for a specific type of service.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnMessMonEntry  

adnMinTimeBetLS 3.1.637.3.1.5.8.2.1.1
Minimum time between self-generated link state messages for the node.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnbroadcastLSU 3.1.637.3.1.5.8.2.1.2
If active, a trigger for a one shot link state update broadcast for this node. The status is reset to inactive when done.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER other(1), active(2), inactive(3)  

adnLSUbroadcastfreez 3.1.637.3.1.5.8.2.1.3
Status of the link state update processing. When the status is active, no link state update for the node is broadcast for a period of time.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER other(1), active(2), inactive(3)  

adnTblDistfreez 3.1.637.3.1.5.8.2.1.4
Status of the table distribution processor. When the status is active, the table distributions sent to a coupler card are frozen.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER other(1), active(2), inactive(3)  

adnManNPhdrTable 3.1.637.3.1.5.8.3
Information about the headers of the manual node-to-path tables for all types of service and criteria.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnManNPhdrEntry

adnManNPhdrEntry 3.1.637.3.1.5.8.3.1
Each row provides information about the header of a specific manual node-to-path table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnManNPhdrEntry  

adnManNPhdrVer 3.1.637.3.1.5.8.3.1.1
Version number of the manual node-to-path table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnManNPhdrStamp 3.1.637.3.1.5.8.3.1.2
Time-of-day stamp of the manual node-to-path table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnManNPhdrNum 3.1.637.3.1.5.8.3.1.3
Number of destination node entries in the manual node-to-path table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnManNPPathhdrTable 3.1.637.3.1.5.8.4
Defines access to information in the destination node entry headers (Dnode headers) of the manual node-to-path table on the control unit. Dnode header of a node-to-path table entry gives summary information about the routing to that Dnode. See the associated adnManNPpthTable for path information associated with each Dnode header of the adnManNPPathhdrTable.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnManNPPathhdrEntry

adnManNPPathhdrEntry 3.1.637.3.1.5.8.4.1
Each entry (row) in the adnManNPPathhdrTable provides all the information found in a table entry's header of the manual node-to-path table on the control unit.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnManNPPathhdrEntry  

adnManDnodeIndex 3.1.637.3.1.5.8.4.1.1
A destination node ID identifies an entry in the node-to-path table. HSS routing services treats a node ID.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnRoutingID  

adnManNPhdrNumPth 3.1.637.3.1.5.8.4.1.2
Number of separate paths from the current node to the destination node; note that each path is uniquely associated with an adjacent node.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnManRemNodeMacNum 3.1.637.3.1.5.8.4.1.3
The machine number part of adnManDnodeIndex, the routing node ID of the node at the remote endpoint.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnManRemNodeAreaNum 3.1.637.3.1.5.8.4.1.4
The area number part of adnManDnodeIndex, the routing area number of the node at the remote endpoint.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnManNPpthTable 3.1.637.3.1.5.8.5
Defines access to path information in a destination node entry of the manual node-to-path table on the control unit.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnManNPpthEntry

adnManNPpthEntry 3.1.637.3.1.5.8.5.1
Each entry (row) in the adnManNPpthTable provides all the information in a particular path entry of the manual node-to-path table on the control unit.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnManNPpthEntry  

adnManPathIndex 3.1.637.3.1.5.8.5.1.1
Number that identifies path order: first, second, third, etc. Number of paths in an node-to-path table entry is variable.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnManNPpthCost 3.1.637.3.1.5.8.5.1.2
Cost of getting to the destination from this node using this path.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnManNPpthAJid 3.1.637.3.1.5.8.5.1.3
The node identifier of an adjacent node to which this node is connected, effectively the first hop of a route to the destination node.
Status: deprecated Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnManNPpthIpAdr 3.1.637.3.1.5.8.5.1.4
The IP address of the destination node.
Status: deprecated Access: read-only
OBJECT-TYPE    
  IpAddress  

adnCurNPhdrTable 3.1.637.3.1.5.8.6
Information about the headers of the automatically built node-to-path tables, for all the types of service and criteria. These tables are used for establishing calls within the network.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCurNPhdrEntry

adnCurNPhdrEntry 3.1.637.3.1.5.8.6.1
Each row provides information about the header of a specific automatically built node-to-path table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnCurNPhdrEntry  

adnCurNPhdrVer 3.1.637.3.1.5.8.6.1.1
Version number of the current node-to-path table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCurNPhdrStamp 3.1.637.3.1.5.8.6.1.2
Time-of-day stamp of the current node-to-path table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnCurNPhdrNum 3.1.637.3.1.5.8.6.1.3
Number of destination node entries in the current node-to-path table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCurNPPathhdrTable 3.1.637.3.1.5.8.7
Defines access to information in the destination node entry headers of the current node-to-path table on the control unit. A destination node header of a node-to-path table entry gives summary information about that destination node's routing status. See the associated adnCurNPpthTable for the path information associated with each Dnode of the adnCurNPPathhdrTable.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCurNPPathhdrEntry

adnCurNPPathhdrEntry 3.1.637.3.1.5.8.7.1
Each entry (row) in the adnCurNPPathhdrTable provides all the information found in a table entry's header of the current node-to-path table on the control unit.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnCurNPPathhdrEntry  

adnCurDnodeIndex 3.1.637.3.1.5.8.7.1.1
A destination node ID identifies an entry in the node-to-path table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnRoutingID  

adnCurNPhdrIpAdr 3.1.637.3.1.5.8.7.1.2
The IP address of the adjacent node.
Status: deprecated Access: read-only
OBJECT-TYPE    
  IpAddress  

adnCurNPhdrNumPth 3.1.637.3.1.5.8.7.1.3
Number of paths indicates the number of separate paths from the current node to the destination node; note that each path is uniquely associated with an adjacent node.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCurRemNodeMacNum 3.1.637.3.1.5.8.7.1.4
The machine number part of adnCurDnodeIndex, the routing node ID of the node at the remote endpoint.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCurRemNodeAreaNum 3.1.637.3.1.5.8.7.1.5
The area number part of adnCurDnodeIndex, the routing area number of the node at the remote endpoint.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCurNPpthTable 3.1.637.3.1.5.8.8
Defines access to path information in a destination node entry of a current node-to-path table on the control unit.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCurNPpthEntry

adnCurNPpthEntry 3.1.637.3.1.5.8.8.1
Each entry (row) in the adnCurNPpthTable provides all the information in a particular path entry of the current node-to-path table on the control unit.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnCurNPpthEntry  

adnCurPathIndex 3.1.637.3.1.5.8.8.1.1
Number that identifies path order: first, second, third, etc. Number of paths in a node-to-path table entry is variable.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnCurNPpthCost 3.1.637.3.1.5.8.8.1.2
The cost of getting to the destination from this node using this path.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCurNPpthAJid 3.1.637.3.1.5.8.8.1.3
An adjacent node to which this node is connected.
Status: deprecated Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnManAjhdrTable 3.1.637.3.1.5.8.9
Information about the headers of the manual adjacency tables for all types of service.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnManAjhdrEntry

adnManAjhdrEntry 3.1.637.3.1.5.8.9.1
Each entry (row) provides the information about a header of a specific manual adjacency table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnManAjhdrEntry  

adnManAjhdrVer 3.1.637.3.1.5.8.9.1.1
Version number of the manual adjacency table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnManAjhdrStamp 3.1.637.3.1.5.8.9.1.2
Time-of-day stamp of the manual adjacency table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnManAjhdrNum 3.1.637.3.1.5.8.9.1.3
Number of adjacent node entries in the manual adjacency table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnManAjLinehdrTable 3.1.637.3.1.5.8.10
References to the HSS routing services manual adjacency table on the control unit, used to keep track of adjacent connections, particularly for purposes of load balancing. Node-to-path table path entries reference the adjacency table. The adjacency header table provides access to the information in the adjacency table entry headers. See the adnManAjLineTable for individual lines associated with a particular adjacent node, header.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnManAjLinehdrEntry

adnManAjLinehdrEntry 3.1.637.3.1.5.8.10.1
Each entry (row) in the adnManAjLinehdrTable provides key information about a particular adjacent node.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnManAjLinehdrEntry  

adnManAnodeIndex 3.1.637.3.1.5.8.10.1.1
Each adjacent node ID identifies an entry in the adjacency table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnRoutingID  

adnAJManNumLines 3.1.637.3.1.5.8.10.1.2
Count of the available logical lines in the connection to this adjacent node.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnManAjNodeMacNum 3.1.637.3.1.5.8.10.1.3
The machine number part of adnManAnodeIndex, the routing node ID of the node at the remote endpoint.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnManAjNodeAreaNum 3.1.637.3.1.5.8.10.1.4
The area number part of adnManAnodeIndex, the routing area number of the node at the remote endpoint.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnManAjLineTable 3.1.637.3.1.5.8.11
Access to the line level information in the adjacency table for each adjacent node entry. This table is related to the adnManAjhdrTable, and refers only to the control unit.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnManAjLineEntry

adnManAjLineEntry 3.1.637.3.1.5.8.11.1
Each entry (row) in the adnManAjLineTable provides key information about a particular logical line (channel) to the adjacent node.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnManAjLineEntry  

adnAJManLocIfIndex 3.1.637.3.1.5.8.11.1.1
Identifies, uniquely within a node, a network interface.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAJManMetricCost1 3.1.637.3.1.5.8.11.1.2
Cost in Metric 1 for a particular logical line entry with a specific type of service.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAJManMetricCost2 3.1.637.3.1.5.8.11.1.3
Cost in Metric 2 for a particular logical line entry with a specific type of service.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAJManMetricCost3 3.1.637.3.1.5.8.11.1.4
Cost in Metric 3 for a particular logical line entry with a specific type of service.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAJManRemIfIndex 3.1.637.3.1.5.8.11.1.5
Uniquely identifies a network interface within the HSS remote node. If the remote node is a TPX, this object identifies the T1 interface identifier.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCurAjhdrTable 3.1.637.3.1.5.8.12
Information about the headers of the learned adjacency tables for all types of service.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCurAjhdrEntry

adnCurAjhdrEntry 3.1.637.3.1.5.8.12.1
Each row provides information about a header of a specific learned adjacency table.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnCurAjhdrEntry  

adnCurAjhdrVer 3.1.637.3.1.5.8.12.1.1
Version number of a learned adjacency table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCurAjhdrStamp 3.1.637.3.1.5.8.12.1.2
Time-of-day stamp of a learned adjacency table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnCurAjhdrNum 3.1.637.3.1.5.8.12.1.3
Number of adjacent node entries in a learned adjacency table.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCurAjLinehdrTable 3.1.637.3.1.5.8.13
Refers to the HSS routing services current adjacency table on the control unit used to track adjacent connections, particularly for purposes of load balancing. Node-to-path table path entries reference the adjacency table. The adjacency header table provides access to the information in the adjacency table entry headers. See the related AdnCurAjLineTable for individual lines associated with a particular adjacent node header.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCurAjLinehdrEntry

adnCurAjLinehdrEntry 3.1.637.3.1.5.8.13.1
Each entry (row) in the adnCurAjLinehdrTable provides key information about a particular adjacent node.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnCurAjLinehdrEntry  

adnCurAnodeIndex 3.1.637.3.1.5.8.13.1.1
Each adjacent node ID identifies an entry in the adjacency table. Routing services treats a node ID as an unsigned 32-bit integer.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnRoutingID  

adnAJCurNodetype 3.1.637.3.1.5.8.13.1.2
Node type can be TPX or HSS. Commonly used to distinguish interworking characteristics.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER other(1), tpx(2), hss(3)  

adnAJCurNumLines 3.1.637.3.1.5.8.13.1.3
Number of available logical lines (channels) in the connection to this adjacent node.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAJCurNxtLine 3.1.637.3.1.5.8.13.1.4
Specifies the next logical line to be used for routing message traffic; allows HSS routing services to spread the routing message traffic over all logical lines comprising the connection.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAJNState 3.1.637.3.1.5.8.13.1.5
Identifies a state that governs HSS routing services adjacency formation.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER down(1), init(2), exchange(3), loading(4), full(5)  

adnCurAjNodeMacNum 3.1.637.3.1.5.8.13.1.6
The machine number part of adnCurAnodeIndex, the routing node ID of the node at the remote endpoint.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCurAjNodeAreaNum 3.1.637.3.1.5.8.13.1.7
The area number part of adnCurAnodeIndex, the routing area number of the node at the remote endpoint.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCurAjLineTable 3.1.637.3.1.5.8.14
Gives access to the line level information in the adjacency table for each adjacent node entry. This table is related to the adnCurAjhdrTable and refers only to the control unit.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCurAjLineEntry

adnCurAjLineEntry 3.1.637.3.1.5.8.14.1
Each entry (row) in the adnCurAjLineTable provides key information about a particular logical line (channel) to the adjacent node.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnCurAjLineEntry  

adnAJCurLocIfIndex 3.1.637.3.1.5.8.14.1.1
Uniquely identifies a network interface within a node.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAJCurMetricCost1 3.1.637.3.1.5.8.14.1.2
Cost in Metric 1 for a particular logical line entry with a specific type of service.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAJCurMetricCost2 3.1.637.3.1.5.8.14.1.3
Cost in Metric 2 for a particular logical line entry with a specific type of service.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAJCurMetricCost3 3.1.637.3.1.5.8.14.1.4
Cost in Metric 3 for a particular logical line entry with a specific type of service.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAJCurRemIfIndex 3.1.637.3.1.5.8.14.1.5
Uniquely identifies a network interface within the HSS remote node. If the remote node is a TPX, this object identifies the T1 interface identifier.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnLahdrTable 3.1.637.3.1.5.8.15
Provides information about the headers of the local address table separate for each numbering plan.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnLahdrEntry

adnLahdrEntry 3.1.637.3.1.5.8.15.1
Each entry (row) provides information about a header of a specific numbering plan local address table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnLahdrEntry  

adnNumPlanIndex 3.1.637.3.1.5.8.15.1.1
Type of address; for example, X.121.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRoutesNumPlan  

adnLahdrVer 3.1.637.3.1.5.8.15.1.2
Local Address header version number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnLahdrStamp 3.1.637.3.1.5.8.15.1.3
Time-of-day stamp of the local address table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnLahdrNum 3.1.637.3.1.5.8.15.1.4
Number of address entries in the local address table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnLaTable 3.1.637.3.1.5.8.16
Represents the HSS routing services local address table on the control unit and provides access to information used to complete call routing to an access point within the current node.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnLaEntry

adnLaEntry 3.1.637.3.1.5.8.16.1
Each entry (row) in the adnLaTable maps a (local) address supported in the node to its internal identifier.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnLaEntry  

adnLaAdIndex 3.1.637.3.1.5.8.16.1.1
Address, maintained as ASCII decimal.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

adnLaIfIndex 3.1.637.3.1.5.8.16.1.2
Interface number at the routing completion point.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAnhdrTable 3.1.637.3.1.5.8.17
Information about the headers of the address-to-node table for each numbering plan.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAnhdrEntry

adnAnhdrEntry 3.1.637.3.1.5.8.17.1
Each row provides information about a header of a specific numbering plan table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAnhdrEntry  

adnAnhdrNumPlanIndex 3.1.637.3.1.5.8.17.1.1
Type of address; for example, X.121.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRoutesNumPlan  

adnAnhdrVer 3.1.637.3.1.5.8.17.1.2
Version number of the address-to-node mapping table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAnhdrStamp 3.1.637.3.1.5.8.17.1.3
Time-of-day stamp of the address-to-node mapping table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnAnhdrNum 3.1.637.3.1.5.8.17.1.4
Number of address entries in the address-to-node mapping table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAnTable 3.1.637.3.1.5.8.18
HSS routing services address-to-node mapping table on the control unit. The address-to-node table records the node(s) in the network that supports the specified address. This table is used only by the frame relay type of service.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAnEntry

adnAnEntry 3.1.637.3.1.5.8.18.1
Each entry (row) in the adnAnTable that maps an address supported in the network to the node(s) where it is supported. An address may be supported multiple times.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAnEntry  

adnAnNumPlanIndex 3.1.637.3.1.5.8.18.1.1
Type of address; for example, X.121.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRoutesNumPlan  

adnAnAdIndex 3.1.637.3.1.5.8.18.1.2
Target address, maintained as ASCII decimal.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

adnAnNodeIndex 3.1.637.3.1.5.8.18.1.3
Node ID for a specific node which supports the target address. Since a single target address may be supported by more than one node (several service-gateway nodes for instance), there should be a separate entry for each one.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnAnRank 3.1.637.3.1.5.8.18.1.4
Rank (cost order) of the node ID to reach the address. The rank of the entry with the lowest cost is 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAnNodeMacNum 3.1.637.3.1.5.8.18.1.5
The machine number part of adnAnNodeIndex, the routing node ID of the node at the remote endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAnNodeAreaNum 3.1.637.3.1.5.8.18.1.6
The area number part of adnAnNodeIndex, the routing area number of the node at the remote endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAnPartialAddrFlag 3.1.637.3.1.5.8.18.1.7
When a sequence of addresses is homing through a single gateway (Gateway 1), a user can enter a partial address by setting Partial Address Flag to `YES' to support the entire range of addresses. E.g.: 31103600 to 31103699 are going to Gateway 1. User can enter 311036 to Gateway 1 with adnAnPartialAddrFlag `yes'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

adnAnAddrLength 3.1.637.3.1.5.8.18.1.8
The number of digits in the Address that is supported by network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnStatsNodeTable 3.1.637.3.1.5.8.19
Statistics node table that gives access to node level information.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnStatsNodeEntry

adnStatsNodeEntry 3.1.637.3.1.5.8.19.1
Each entry (row) in the adnStatsNodeTable provides node level statistics.
Status: deprecated Access: not-accessible
OBJECT-TYPE    
  AdnStatsNodeEntry  

adnStatsTotLSU 3.1.637.3.1.5.8.19.1.1
The number of link state update messages received from the specified node.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnStatsTotDupLSU 3.1.637.3.1.5.8.19.1.2
The number of duplicate link state update messages, received from the specified node, that were discarded.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnStatsTotOldLSU 3.1.637.3.1.5.8.19.1.3
The number of link state update messages received from the specified node, that were too old and had to be discarded.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnRtsCritCountGroup 3.1.637.3.1.5.8.20
OBJECT IDENTIFIER    

adnRtsCritCount 3.1.637.3.1.5.8.20.1
The number of entries in the criterion cost summary table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnRtsCritSmryTable 3.1.637.3.1.5.8.21
This table summarizes each supported criterion cost, giving the ID (unique identifier) and the order and IDs of the three cost metrics that comprise the criterion cost.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnRtsCritSmryEntry

adnRtsCritSmryEntry 3.1.637.3.1.5.8.21.1
An entry in the routing criteria summary table. Each entry represents a particular routing criterion. For a routing criterion consisting of the ordered set of metric types { metric1, metric2, metric3 } registered as { adnRoutingCriteria n }, the object adnRtsCritID will have the value 'n', adnRtsCritOID will have the value '{ adnRoutingCriteria n }', adnRtsCritMetricHigh will have the value 'metric1', adnRtsCritMetricMid will have the value 'metric2' and adnRtsCritMetricLow will have the value 'metric3'.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRtsCritSmryEntry  

adnRtsCritID 3.1.637.3.1.5.8.21.1.1
The entry number for this entry in this criterion cost summary table. This value ranges from 1 to the value of adnRtsCritCount and is equal to the rightmost sub-identifier of the corresponding adnRtsCritOID value.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnRtsCritOID 3.1.637.3.1.5.8.21.1.2
The routing criterion object identifier corresponding to adnRtsCritID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingCriteriaType  

adnRtsCritMetricHigh 3.1.637.3.1.5.8.21.1.3
The highest priority routing metric type of this routing criterion cost type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingMetricType  

adnRtsCritMetricMid 3.1.637.3.1.5.8.21.1.4
The second highest priority routing metric type in this routing criterion cost type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingMetricType  

adnRtsCritMetricLow 3.1.637.3.1.5.8.21.1.5
The third highest priority routing metric type in this routing criterion cost type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingMetricType  

adnCalcCtlTable 3.1.637.3.1.5.8.22
General parameters used by the routing services for node-to-path table calculation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCalcCtlEntry

adnCalcCtlEntry 3.1.637.3.1.5.8.22.1
Each entry (row) of the adnCalcCtlTable provides the general parameters used by the routing services for node-to-path table calculation for a specific type of service and criterion. Note that there are 3 metric types known in R 2.2. Additional metric types may be added at the end of the entry, as future requirements dictate.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnCalcCtlEntry  

adnTosIndex 3.1.637.3.1.5.8.22.1.1
Type of service: frame relay, ATM virtual channel, ATM virtual path, etc.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), fr(2), atmVc(3), atmVp(4)  

adnMaxNumPath 3.1.637.3.1.5.8.22.1.2
Maximum number of paths to be presented in the node-to-path routing table, for a given destination node, for a specific type of service and criterion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnMinTimeBtwCalc 3.1.637.3.1.5.8.22.1.3
Minimum time between successive route calculations for a specific type of service and criterion.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnMetricDefHigh 3.1.637.3.1.5.8.22.1.4
The high priority default cost metric value used for the specified Type Of Service (TOS), criterion. The default value is set up at initialization. Thus, initially, 'adnMetricMaxHigh' is equal to 'adnMetricDefHigh'. This 'adnMetricDefHigh' allows easy recall of exactly what the default value is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnMetricMaxHigh 3.1.637.3.1.5.8.22.1.5
The current maximum value for the high priority cost metric value. Initialized to a release specific default, SNMP changeable. The value of the object 'adnMetricMaxHigh' is what is actually used by the routing software. A key use is to identify calculated paths 'too costly' to be considered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnMetricDefMid 3.1.637.3.1.5.8.22.1.6
The mid-priority default cost metric value used for the specified Type Of Service (TOS), criterion. The default value is set up at initialization. Thus, initially, 'adnMetricMaxMid' is equal to 'adnMetricDefMid'. This 'adnMetricDefMid' allows easy recall of exactly what the default value is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnMetricMaxMid 3.1.637.3.1.5.8.22.1.7
The current maximum value for the mid-priority cost metric value. Initialized to a release specific default, SNMP changeable. The value of the object 'adnMetricMaxMid' is what is actually used by the routing software. A key use is to identify calculated paths 'too costly' to be considered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnMetricDefLow 3.1.637.3.1.5.8.22.1.8
The low-priority default cost metric value used for the specified Type Of Service, criterion. The default value is set up at initialization. Thus, initially, 'adnMetricMaxLow' is equal to 'adnMetricDefLow'. This 'adnMetricDefLow' allows easy recall of exactly what the default value is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnMetricMaxLow 3.1.637.3.1.5.8.22.1.9
The current maximum value for the low-priority cost metric value. Initialized to a release specific default, SNMP changeable. The value of the object 'adnMetricMaxLow' is what is actually used by the routing software. A key use is to identify calculated paths 'too costly' to be considered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnNPhdrTable 3.1.637.3.1.5.8.23
Information about the headers of the automatically built node-to-path tables, for all the types of service and criteria. These tables are used for establishing calls within the network.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnNPhdrEntry

adnNPhdrEntry 3.1.637.3.1.5.8.23.1
Each row provides information about the header of a specific automatically built node-to-path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnNPhdrEntry  

adnNPhdrVer 3.1.637.3.1.5.8.23.1.1
Version number of the current node-to-path table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnNPhdrStamp 3.1.637.3.1.5.8.23.1.2
Time-of-day stamp of the current node-to-path table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnNPhdrNum 3.1.637.3.1.5.8.23.1.3
Number of destination node entries in the node-to-path table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnNPPathhdrTable 3.1.637.3.1.5.8.24
Defines access to information in the destination node entry headers of the node-to-path table on the control unit. A destination node header of a node-to-path table entry gives summary information about that destination node's routing status. See the associated adnNodePathTable for the path information associated with each destination node of the adnNPPathhdrTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnNPPathhdrEntry

adnNPPathhdrEntry 3.1.637.3.1.5.8.24.1
Each entry (row) in the adnNPPathhdrTable provides all the information found in a table entry's header of the current node-to-path table on the control unit.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnNPPathhdrEntry  

adnDnodeIndex 3.1.637.3.1.5.8.24.1.1
A destination node ID identifies an entry in the node-to-path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRoutingID  

adnNPhdrIpAdr 3.1.637.3.1.5.8.24.1.2
The IP address of the adjacent node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

adnNPhdrNumPth 3.1.637.3.1.5.8.24.1.3
Number of separate paths from the current node to the destination node; note that each path is uniquely associated with an adjacent node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnRemNodeMacNum 3.1.637.3.1.5.8.24.1.4
The machine number part of adnDnodeIndex, the routing node ID of the node at the remote endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnRemNodeAreaNum 3.1.637.3.1.5.8.24.1.5
The area number part of adnDnodeIndex, the routing area number of the node at the remote endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnNodePathTable 3.1.637.3.1.5.8.25
Defines access to path information in a destination node entry of a current node-to-path table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnNodePathEntry

adnNodePathEntry 3.1.637.3.1.5.8.25.1
Each entry (row) in the adnNodePathTable provides all the information in a particular path entry of the current node-to-path table on the control unit.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnNodePathEntry  

adnNodePathIndex 3.1.637.3.1.5.8.25.1.1
Number that identifies path order: first, second, third, etc. Number of paths in a node-to-path table entry is variable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnNodePathAdjNodeID 3.1.637.3.1.5.8.25.1.2
An adjacent node to which this node is connected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnNodePathCostHigh 3.1.637.3.1.5.8.25.1.3
The high priority cost metric value for getting to this destination node using this path from 'adnNodePathAdjNodeID' node using this path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnNodePathCostMid 3.1.637.3.1.5.8.25.1.4
The middle priority cost metric value for getting to this destination node using this path from 'adnNodePathAdjNodeID' node using this path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnNodePathCostLow 3.1.637.3.1.5.8.25.1.5
The lowpriority cost metric value for getting to this destination node using this path from 'adnNodePathAdjNodeID' node using this path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnNodePathRemNodeMacNum 3.1.637.3.1.5.8.25.1.6
The machine number part of adnNodePathAdjNodeID, the routing node ID of the node at the remote endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnNodePathRemNodeAreaNum 3.1.637.3.1.5.8.25.1.7
The area number part of adnNodePathAdjNodeID, the routing node ID of the node at the remote endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAdjhdrTable 3.1.637.3.1.5.8.26
Information about the headers of the learned adjacency tables for all types of service.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAdjhdrEntry

adnAdjhdrEntry 3.1.637.3.1.5.8.26.1
Each row provides information about a header of a specific learned adjacency table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAdjhdrEntry  

adnAdjhdrVer 3.1.637.3.1.5.8.26.1.1
Version number of a learned adjacency table. These numbers start at 1 and continue upwards - allows distinguishing older from newer copies.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAdjhdrStamp 3.1.637.3.1.5.8.26.1.2
Time-of-day stamp of a learned adjacency table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnAdjhdrNum 3.1.637.3.1.5.8.26.1.3
Number of adjacent node entries in a learned adjacency table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAdjLinehdrTable 3.1.637.3.1.5.8.27
Refers to the HSS routing services learned adjacency table on the control unit used to track adjacent connections, particularly for purposes of load balancing. Node-to-path table path entries reference the adjacency table. The adjacency header table provides access to the information in the adjacency table entry headers. See the related AdnAjLineTable for individual lines associated with a particular adjacent node header.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAjLinehdrEntry

adnAjLinehdrEntry 3.1.637.3.1.5.8.27.1
Each entry (row) in the adnAdjLinehdrTable provides key information about a particular adjacent node.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAjLinehdrEntry  

adnAnodeIndex 3.1.637.3.1.5.8.27.1.1
Each adjacent node ID identifies an entry in the adjacency table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRoutingID  

adnAdjNodetype 3.1.637.3.1.5.8.27.1.2
Node type can be TPX or HSS. Commonly used to distinguish interworking characteristics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), tpx(2), hss(3)  

adnAdjNumLines 3.1.637.3.1.5.8.27.1.3
Number of available logical lines (channels) in the connection to this adjacent node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAdjNxtLine 3.1.637.3.1.5.8.27.1.4
Specifies the next logical line to be used for routing message traffic; allows HSS routing services to spread the routing message traffic over all logical lines comprising the connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAdjNodeState 3.1.637.3.1.5.8.27.1.5
Identifies a state that governs HSS routing services adjacency formation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), init(2), exchange(3), loading(4), full(5)  

adnAdjRemNodeMacNum 3.1.637.3.1.5.8.27.1.6
The machine number part of adnAnodeIndex, the routing node ID of the node at the remote endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAdjRemNodeAreaNum 3.1.637.3.1.5.8.27.1.7
The area number part of adnAnodeIndex, the routing area number of the node at the remote endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAdjTpxAddr 3.1.637.3.1.5.8.27.1.8
The adjacent TPX node's x121 Address. If adnAdjNodetype is not TPX the address is 00000....
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnAdjhdrIpAdr 3.1.637.3.1.5.8.27.1.9
The IP address of the adjacent node. If the adjacent node does not have IP address then the value is 0.0.0.0
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

adnAdjLineTable 3.1.637.3.1.5.8.28
Provides access to the line level information in the adjacency table for each adjacent node entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAdjLineEntry

adnAdjLineEntry 3.1.637.3.1.5.8.28.1
Each entry (row) in the adnAdjLineTable provides key information about a particular logical line (channel) to the adjacent node.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAdjLineEntry  

adnAdjLocIfIndex 3.1.637.3.1.5.8.28.1.1
Uniquely identifies a network interface within a node.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

adnAdjRemIfIndex 3.1.637.3.1.5.8.28.1.2
Uniquely identifies a network interface within the remote node. If the remote node is a TPX, this object identifies the T1 interface identifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnAdjMetricIDHigh 3.1.637.3.1.5.8.28.1.3
High priority cost metric ID for this link entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingMetricType  

adnAdjMetricCostHigh 3.1.637.3.1.5.8.28.1.4
High priority cost metric for this link entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAdjMetricIDMid 3.1.637.3.1.5.8.28.1.5
Mid priority cost metric ID for this link entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingMetricType  

adnAdjMetricCostMid 3.1.637.3.1.5.8.28.1.6
Mid priority cost metric for this link entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAdjMetricIDLow 3.1.637.3.1.5.8.28.1.7
Low priority cost metric ID for this link entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingMetricType  

adnAdjMetricCostLow 3.1.637.3.1.5.8.28.1.8
Low priority cost metric for this link entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAdjRemTpxTci 3.1.637.3.1.5.8.28.1.9
This variable provides the value of remote TPX TCI (TPX Channel Indicator) which corresponds to this ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnMsgMonTable 3.1.637.3.1.5.8.29
General parameters used by the routing services for routing message handling.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnMsgMonEntry

adnMsgMonEntry 3.1.637.3.1.5.8.29.1
Each entry (row) of the adnMsgMonTable provides the general parameters used by the routing services for routing message handling for a specific type of service.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnMsgMonEntry  

adnRtsMinTimeBetLS 3.1.637.3.1.5.8.29.1.1
Minimum time between self-generated link state messages for the node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnRtsbroadcastLSU 3.1.637.3.1.5.8.29.1.2
If active, a trigger for a one shot link state update broadcast for this node. The status is reset to inactive when done.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), active(2), inactive(3)  

adnRtsLSUbroadcastfreez 3.1.637.3.1.5.8.29.1.3
Status of the link state update processing. When the status is active, no link state update for the node is broadcast for a period of time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), active(2), inactive(3)  

adnRtsTblDistfreez 3.1.637.3.1.5.8.29.1.4
Status of the table distribution processor. When the status is active, the table distributions sent to a coupler card are frozen.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), active(2), inactive(3)  

adnRtsMHStatsTable 3.1.637.3.1.5.8.30
Statistics regarding Routes Message Handler activity associated with particular network nodes, by Type Of Service(TOS), are provided in this table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnRtsMHStatsEntry

adnRtsMHStatsEntry 3.1.637.3.1.5.8.30.1
Each entry (row) in the adnRtsMHStatsTable provides node level statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRtsMHStatsEntry  

adnRtsMHTotLSU 3.1.637.3.1.5.8.30.1.1
The number of link state update messages received from the specified node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnRtsMHTotDupLSU 3.1.637.3.1.5.8.30.1.2
The number of duplicate link state update messages, received from the specified node, that were discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnRtsMHTotOldLSU 3.1.637.3.1.5.8.30.1.3
The number of link state update messages received from the specified node, that were too old and had to be discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnLocalAddrTable 3.1.637.3.1.5.8.31
Represents the HSS routing services local address table on the control unit and provides access to information used to complete call routing to an access point within the current node.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnLaEntry

adnLocalAddrEntry 3.1.637.3.1.5.8.31.1
Each entry (row) in the adnLocalAddrTable maps a (local) address supported in the node to a local interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnLocalAddrEntry  

adnLocalAddrIndex 3.1.637.3.1.5.8.31.1.1
Address, maintained as ASCII decimal.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

adnLocalAddrNumIfIndex 3.1.637.3.1.5.8.31.1.2
Number of ifindex per local address end point or Interface number at the routing completion point.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnLocalAddrIfIndex 3.1.637.3.1.5.8.31.1.3
Value of Interface Index for each Local Address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnRtsGlobalGroup 3.1.637.3.1.5.8.32
OBJECT IDENTIFIER    

adnRtsDefaultNodeID 3.1.637.3.1.5.8.32.1
This routing node ID is used if there is no matching entry (exact or partial) for a destination address in the address to node table (adnAnTable). This is created in response to CDC # 8447 to add 'sink address' feature for IISP. The default value is '0'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnRoutingID  

adnSfasMIB 3.1.637.3.1.5.9
OBJECT IDENTIFIER    

adnSaSystem 3.1.637.3.1.5.9.1
OBJECT IDENTIFIER    

adnNodeTime 3.1.637.3.1.5.9.1.1
The value of this object identifies the current Coordinated Universal Time (UTC) expressed in elapsed seconds by reading the UTC real-time clock on the control unit (CU) board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnNodeTimeTicks  

adnNodeResyncTrap 3.1.637.3.1.5.9.1.2
Indicates whether the SNMP agent needs to send adnNodeResync traps. This object is set to true whenever the control unit (CU) board is reinitialized. The SNMP agent keeps sending adnNodeResync traps until the NMS acknowledges the trap by sending an SNMP Set request to reset this object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TruthValue  

adnSaConfigFrom 3.1.637.3.1.5.9.1.3
This value is used to indicate whether the node has been fully configured from the NMS, or whether the node has been installed for the first time using an HSS installation tool. In the case that an HSS installation tool was used to configure the HSS (either the HSS Installation Tool called HIT, or OSCAR, the On-Site Configuration And Restart tool), the full set of configuration files has not yet been downloaded to the node from the Network Management System.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER nms(1), hit(2)  

adnSaViews 3.1.637.3.1.5.9.2
OBJECT IDENTIFIER    

adnViewTable 3.1.637.3.1.5.9.2.1
The Customer Network Management (CNM) View table which contains an additional object for the Context table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnViewEntry

adnViewEntry 3.1.637.3.1.5.9.2.1.1
An entry containing Customer Network Management (CNM) view information applicable to a particular context.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnViewEntry  

adnViewIndex 3.1.637.3.1.5.9.2.1.1.1
If the value of an instance of this object is greater than zero, then this corresponding conceptual row in the contextTable refers to a Customer Network Management (CNM) view. The value of the instance identifies the particular CNM view which has the same value as the instance of the adnCnmIndex object. If the value of an instance of this object is zero, then there is no CNM view.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCnmTable 3.1.637.3.1.5.9.2.2
The Customer Network Management (CNM) database.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCnmEntry

adnCnmEntry 3.1.637.3.1.5.9.2.2.1
An entry containing information on a particular family of Customer Network Management (CNM) interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnCnmEntry  

adnCnmIndex 3.1.637.3.1.5.9.2.2.1.1
A unique value for each Customer Network Management (CNM) view. The value for each CNM view must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnCnmIfIndex 3.1.637.3.1.5.9.2.2.1.2
The value of this object is equal to MIB II's ifIndex value. This Customer Network Management (CNM) interface should be a physical line or channel.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCnmAccess 3.1.637.3.1.5.9.2.2.1.3
The access type of a particular family of Customer Network Management (CNM) interfaces within the particular CNM view. The value 'none(1)' indicates that the corresponding instance of adnCnmIfIndex defines a CNM interface which is not accessible. The value 'read(2)' indicates that the corresponding instance of adnCnmIfIndex defines a CNM interface which is read-only. The value 'write(3)' indicates that the corresponding instance of adnCnmIfIndex defines a CNM interface with read-write permissions.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), read(2), write(3)  

adnCnmType 3.1.637.3.1.5.9.2.2.1.4
The status of a particular family of Customer Network Management (CNM) interfaces within the particular CNM view. The value 'included(1)' indicates that the corresponding instance of adnCnmIfIndex defines a CNM interface included in the CNM view. The value 'excluded(2)' indicates that the corresponding instance of adnCnmIfIndex defines a CNM interface excluded from the CNM view.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER included(1), excluded(2)  

adnSaTrapFilter 3.1.637.3.1.5.9.3
OBJECT IDENTIFIER    

adnTrapEnableCritical 3.1.637.3.1.5.9.3.1
Indicates whether the SNMP agent is permitted to generate critical traps. The value of this object provides a means whereby all critical traps may be disabled. Common name: Send Critical Traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnTrapEnableMajor 3.1.637.3.1.5.9.3.2
Indicates whether the SNMP agent is permitted to generate major traps. The value of this object provides a means whereby all major traps may be disabled. Common name: Send Major Traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnTrapEnableMinor 3.1.637.3.1.5.9.3.3
Indicates whether the SNMP agent is permitted to generate minor traps. The value of this object provides a means whereby all minor traps may be disabled. Common name: Send Minor Traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnTrapEnableStr 3.1.637.3.1.5.9.3.4
Indicates whether the SNMP agent is permitted to generate STR (Software Trouble Report) traps. The value of this object provides a means whereby all STR traps may be disabled. Common name: Send SW Trouble Traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnTrapEnableDiagnostic 3.1.637.3.1.5.9.3.5
Indicates whether the SNMP agent is permitted to generate diagnostic traps. The value of this object provides a means whereby all diagnostic traps may be disabled. Common name: Send Diagnostic Traps.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnTrapEnableCleared 3.1.637.3.1.5.9.3.6
Indicates whether the SNMP agent is permitted to generate cleared traps. The value of this object provides a means whereby all cleared traps may be disabled. Common name: Trap Enable Cleared.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnSaUtility 3.1.637.3.1.5.9.4
OBJECT IDENTIFIER    

adnSaSnmpTimer 3.1.637.3.1.5.9.4.1
The value of this object identifies the length of the SNMP response timer, measured in seconds. The timer starts on receipt of an SNMP request. If an SNMP response cannot be returned to the NMS within that time, the SNMP command fails.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnSaInmpTimer 3.1.637.3.1.5.9.4.2
The value of this object identifies the length of the Internal Network Management Protocol (INMP) response timer, measured in seconds. The timer starts whenever an INMP command is sent to another subsystem. If no reply is received within that time, the INMP command fails. The value of this object should be less than the value of adnSaSnmpTimer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnSaMibMgt 3.1.637.3.1.5.9.5
OBJECT IDENTIFIER    

adnSaMIBFilePathName 3.1.637.3.1.5.9.5.1
The value of this object is the path and filename of the MIB template that is loaded in the agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnSaQtpGroup 3.1.637.3.1.5.9.6
OBJECT IDENTIFIER    

adnSaQtpInitial 3.1.637.3.1.5.9.6.1
Indicates whether the Quick Transfer Protocol is being initialized for a new sequence of SNMP Set messages. This value is set to true by the NMS in the first SNMP Set command of a sequence used to transfer a group of configuration files. The HSS resets the value of this object back to false immediately.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TruthValue  

adnSaQtpFileName 3.1.637.3.1.5.9.6.2
The value of this object is the filename of a configuration file that is to be created by the SNMP Agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

adnSaQtpFileContents 3.1.637.3.1.5.9.6.3
The value of this object is an octet string containing the contents of a configuration file that is to be created by the SNMP Agent. The file will be named according to the value of adnSaQtpFileName.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adnSaLoggedTrapTable 3.1.637.3.1.5.9.7
The SNMP Agent logged trap table. The SNMP Agent logs in this table the last several traps (up to a maximum of 10) sent from the agent to each destination party. The 1100 NMS will use the trap sequence number information to detect lost traps (from a discontinuity in the received sequence numbers, e.g., number 17 followed by number 20), and will then send an SNMP command to the HSS SNMP Agent to request replay of any lost traps (e.g., 18 and 19). The Logged Trap Table is a circular list. When the maximum capacity is reached (the maximum number of traps are already logged), then the next trap sent out overwrites the oldest trap in the Logged Trap Table. If a request is received to replay more traps than are stored in the Logged Trap Table, then the request will be refused with the SNMP error code genErr(5). The Logged Trap Table is cleared upon HSS CU restart.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSaLoggedTrapEntry

adnSaLoggedTrapEntry 3.1.637.3.1.5.9.7.1
Information about a single trap in the log. Entries in this table are created automatically by the SNMP Agent whenever a trap is sent out.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSaLoggedTrapEntry  

adnSaLoggedTrapPartyIndex 3.1.637.3.1.5.9.7.1.1
The value of partyIndex for the manager to whom the logged trap was sent. This uniquely identifies the receiving manager. The adnSaLoggedTrapPartyIndex and the adnSaLoggedTrapIndex sequence number together uniquely identify the logged trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnSaLoggedTrapIndex 3.1.637.3.1.5.9.7.1.2
The trap sequence number of the logged trap. This object takes the value of the snmpTrapNumbers variable of the logged trap that it references. The adnSaLoggedTrapIndex sequence number and the adnSaLoggedTrapPartyIndex together uniquely identify the logged trap.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnSaLoggedTrapCategory 3.1.637.3.1.5.9.7.1.3
The category of the logged trap. This object takes the value of the adnTrapCategory variable of the logged trap that is referenced by adnSaLoggedTrapIndex and adnSaLoggedTrapPartyIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnSaLoggedTrapReplayTable 3.1.637.3.1.5.9.8
The SNMP Agent logged trap replay table. The 1100 NMS SNMP Manager uses this table to request retransmission from the SNMP agent of any traps which are stored in the Logged Trap Table. The 1100 NMS sends an SNMP Set command, specifying a starting sequence number and an ending sequence number (e.g., 18 and 19). Both sequence numbers must be present in the Logged Trap Table for the command to be successful. The SNMP Set command to request replay of traps must contain each of the following objects in this order: adnSaLoggedTrapReplayFirst, adnSaLoggedTrapReplayLast, adnSaLoggedTrapReplayOn. If one of the objects is missing, or the order is incorrect, an error response will be returned with an SNMP error code of genErr(5). If both starting and ending sequence numbers are found in the Logged Traps Table, the SNMP Agent will then replay the traps, starting with the first one specified, and ending with the last one specified. If the value of adnSaLoggedTrapReplayFirst is equal to adnSaLoggedTrapReplayLast, then only one trap is replayed. The ending sequence number may have a lower value than the starting sequence number, in the case that the trap sequence number has reached its maximum and rolled over through zero. The SNMP Agent will look in the adnSaLoggedTrapTable using the value given in the SNMP Set request for adnSaLoggedTrapReplayPartyIndex as the adnSaLoggedTrapPartyIndex, and using the value of adnSaLoggedTrapReplayFirst as the adnSaLoggedTrapIndex. If the first trap is found in the adnSaLoggedTrapTable, then the SNMP Agent will look for the last trap to be replayed, using the value of adnSaLoggedTrapReplayLast as the adnSaLoggedTrapIndex. If either the first trap to be replayed or the last trap to be replayed cannot be found in the adnSaLoggedTrapTable, then an error response is returned with an SNMP error code of genErr(5). The value of adnSaLoggedTrapReplayOn is set to enabled by the 1100 NMS in the Set command, and is reset to disabled by the SNMP Agent when the command has been processed. If the procesing of the command identifies any traps to be replayed, then these are all sent out immediately by the SNMP Agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSaLoggedTrapReplayEntry

adnSaLoggedTrapReplayEntry 3.1.637.3.1.5.9.8.1
Information corresponding to a replay request from an SNMP Manager.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSaLoggedTrapReplayEntry  

adnSaLoggedTrapReplayPartyIndex 3.1.637.3.1.5.9.8.1.1
The value of partyIndex for the manager to whom the logged traps were originally sent, and who is now requesting the replay.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnSaLoggedTrapReplayFirst 3.1.637.3.1.5.9.8.1.2
The trap sequence number of the first trap in a sequence of one or more logged traps to be replayed. This object takes the value of the snmpTrapNumbers variable of the first trap being requested. The SNMP Agent will look in the adnSaLoggedTrapTable using the given value of adnSaLoggedTrapReplayPartyIndex in the SNMP Set request as the adnSaLoggedTrapPartyIndex, and using the value of this object as adnSaLoggedTrapIndex. After processing a replay command, the SNMP Agent resets this value back to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnSaLoggedTrapReplayLast 3.1.637.3.1.5.9.8.1.3
The trap sequence number of the last trap in a sequence of one or more logged traps to be replayed. This object takes the value of the snmpTrapNumbers variable of the last trap being requested. The SNMP Agent will look in the adnSaLoggedTrapTable using the given value of adnSaLoggedTrapReplayPartyIndex in the SNMP Set request as the adnSaLoggedTrapPartyIndex, and using the value of this object as adnSaLoggedTrapIndex. After processing a replay command, the SNMP Agent resets this value back to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnSaLoggedTrapReplayOn 3.1.637.3.1.5.9.8.1.4
This object is set to a value of enabled by the 1100 NMS to request trap replay. Traps numbered between adnSaLoggedTrapReplayFirst and adnSaLoggedTrapReplayLast are sent by the SNMP Agent to the manager identified by adnSaLoggedTrapReplayPartyIndex. The SNMP Agent resets this value to disabled after processing the request.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnLdrMIB 3.1.637.3.1.5.10
OBJECT IDENTIFIER    

adnLdrChanTable 3.1.637.3.1.5.10.1
This table contains all the fields supported by all the line drivers. It contains configuration, control and statistics information for the channel.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnLdrChanEntry

adnLdrChanEntry 3.1.637.3.1.5.10.1.1
An entry in the line driver (LDR) table. There is one entry for each LDR channel configured.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnLdrChanEntry  

adnLdrChanType 3.1.637.3.1.5.10.1.1.1
Type of line driver to which the channel belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER vSeries(1), g703(2), flip(3)  

adnLdrChanStatisticsFlag 3.1.637.3.1.5.10.1.1.2
Flag indicates if statistics is enabled on this channel. Common Name: Statistics
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnLdrChanSubFrameIN 3.1.637.3.1.5.10.1.1.3
Number of sub-frames received by the line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanAbortIN 3.1.637.3.1.5.10.1.1.4
Number of received frames aborted (G.703 (DS1 or E1) line driver only). This object is not relevant to the v-series (RS232, V.35, V36, or X.21) or FLIP (fake line internal process) line drivers which will respond to an SNMP Get command with a value of zero. This object has the same value as rs232SyncPortAbortedFrames in the rs232SyncPortTable for the v-series line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanCrcErrIN 3.1.637.3.1.5.10.1.1.5
Number of frames received with a CRC errors (G.703 (DS1 or E1) line driver only). This object is not relevant to the v-series (RS232, V.35, V.36, or X.21) or FLIP (fake line internal process) line drivers which will respond to an SNMP Get command with a value of zero. This object has the same value as rs232SyncPortFrameCheckErr in the rs232SyncPortTable for the v-series line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanOverRunErrIN 3.1.637.3.1.5.10.1.1.6
Number of sub-frames received which have overrun errors (G.703 (DS1 or E1) line driver only). This object is not relevant to the v-series (RS232, V.35, V.36, or X.21) or FLIP (fake line internal process) line drivers which will respond to an SNMP Get command with a value of zero. This object has the same value as rs232SyncPortReceiveOverrunErrs in the rs232SyncPortTable for the v-series line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanOctetAlignErrIN 3.1.637.3.1.5.10.1.1.7
Number of sub-frames received with misaligned octet errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanBusyErrIN 3.1.637.3.1.5.10.1.1.8
Number of sub-frames received which have the busy error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanAbortOUT 3.1.637.3.1.5.10.1.1.9
Number of aborts that occurred during transmission (G.703 (DS1 or E1) line driver only). This object is not relevant to the v-series (RS232, V.35, V.36, or X.21) or FLIP (fake line internal process) line drivers which will respond to an SNMP Get command with a value of zero. This object has the same value as rs232SyncPortInterruptedFrames in the rs232SyncPortTable for the v-series line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanUnderRunErrOUT 3.1.637.3.1.5.10.1.1.10
Number of underrun error that occurred during transmission (G.703 (DS1 or E1) line driver only). This object is not relevant to the v-series or FLIP (fake line internal process) line drivers which will respond to an SNMP Get command with a value of zero. This object has the same value as rs232SyncPortTransmitUnderrunErrs in the rs232SyncPortTable for the v-series Line Driver (LDR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanNumOfFlags 3.1.637.3.1.5.10.1.1.11
The minimum number of flags to recognize the end of one frame and the start of the next (G.703 (DS1 or E1) line driver only). This object is not relevant to the v-series or FLIP (fake line internal process) line drivers which will respond to an SNMP Get command with a value of zero. This object has the same value as rs232SyncPortMinFlags in the rs232SyncPortTable for the v-series Line Driver(LDR).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnLdrChanFlagOrIdle 3.1.637.3.1.5.10.1.1.12
This indicates whether flags or idle code is used between frames. Common Name: Flags or Idle Between Frames
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER flag(1), idle(2)  

adnLdrChanTimeSlotMask 3.1.637.3.1.5.10.1.1.13
This defines the bit location for framed subrate channels (G.703 (DS1 or E1) line driver only). This object is not relevant to the v-series or FLIP (fake line internal preocess) line drivers which will respond to an SNMP Get command with a value of zero. This object is related to dsx1LineCoding in the DS1/E1 MIB. For B8ZS (Binary-8 Zero Suppression) and HDB3 (ITU G.703 standard for E1 lines), the usual value is clear64Kbps, but the user can change this to any value. For AMI (Alternate Mark Inversion), the usual value is b8jam56Kbps, but the user can change this to any value except clear64Kbps (because it would violate pulse density). Note that the numerical values of adnLdrChanTimeSlotMask have been chosen so that they correspond to the one's complement of the bit mask used by the hardware. clear64Kbps = Binary 00000000 b8jam56Kbps = Binary 00000001 b7jam56Kbps = Binary 00000010 Any additions to this object's values should follow the same principle. Common Name: Pulse Density Mask
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER clear64kbps(0), b8jam56kbps(1), b7jam56kbps(2)  

adnLdrChanFramed 3.1.637.3.1.5.10.1.1.14
This indicates whether the G.703 (DS1 or E1) interface is framed or unframed (G.703 line driver only). This object is not relevant to the v-series (RS-232, V.35, V.36, or X.21) or FLIP (fake line internal process) line drivers which will respond to an SNMP Get command with a value of zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER framed(1), unframed(2)  

adnLdrChanCosRtOutOctets 3.1.637.3.1.5.10.1.1.15
Number of Real-time Class of Service Octets transmitted by the line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanCosRtOutPkts 3.1.637.3.1.5.10.1.1.16
Number of Real-time Class of Service packets (frame or subframes) transmitted by the line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanCosRtOutErrors 3.1.637.3.1.5.10.1.1.17
Number of errors while transmitting Real-time Class of Service data by the line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanCosNrtOutOctets 3.1.637.3.1.5.10.1.1.18
Number of Non-real-time Class of Service Octets transmitted by the line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanCosNrtOutPkts 3.1.637.3.1.5.10.1.1.19
Number of Non-real-time Class of Service packets (frame or subframes) transmitted by the line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLdrChanCosNrtOutErrors 3.1.637.3.1.5.10.1.1.20
Number of errors while transmitting Non-real-time Class of Service data by the line driver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnNmgsMIB 3.1.637.3.1.5.11
OBJECT IDENTIFIER    

adnAmGroup 3.1.637.3.1.5.11.1
OBJECT IDENTIFIER    

adnFmGroup 3.1.637.3.1.5.11.2
OBJECT IDENTIFIER    

adnPmHsGroup 3.1.637.3.1.5.11.3
OBJECT IDENTIFIER    

adnPmIsGroup 3.1.637.3.1.5.11.4
OBJECT IDENTIFIER    

adnDumGroup 3.1.637.3.1.5.11.5
OBJECT IDENTIFIER    

adnAmEnableAccounting 3.1.637.3.1.5.11.1.1
Indicates whether accounting data is collected and processed for all subscribing applications on the node by the Node Management Subsystem. Common Name: Node Accounting
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnAmCollectInterval 3.1.637.3.1.5.11.1.2
Defines the time period between collections of accounting data. The unit of time for this interval is minutes. Common Name: Acctg Collection Interval
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnAmPostInterval 3.1.637.3.1.5.11.1.3
Defines a time period between transfers of the accounting data file to the Network Management System directory. After each transfer, the Network Management System is also notified via a SNMP trap that this file is ready for transfer to the Network Management System via FTP services. Each posting contains only accounting data collected since the last posting. The unit of time for this interval is minutes. Common Name: Acctg Posting Interval
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnAmPostAccounting 3.1.637.3.1.5.11.1.4
When adnAmPostAccounting is enabled, a file containing the current accounting data is transferred to the Network Management System directory and the Network Management System is subsequently notified via a SNMP trap that this file is ready for transfer to the Network Management System via FTP services. This file contains all the accounting data collected since the lasting posting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnAmMakeAccounting 3.1.637.3.1.5.11.1.5
When adnAmMakeAccounting is enabled, the accounting data from all applications that have registered for the service are requested and collected in a common file. After waiting the time interval defined in adnAmMakeAccountingWindow to receive all responses, the accounting file is transferred to the Network Management System directory and the Network Management System is notified via a SNMP trap that this file is ready for transfer to the Network Management System via FTP services.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnAmMakeAccountingWindow 3.1.637.3.1.5.11.1.6
When adnAmMakeAccounting is enabled, accounting data is requested from all applications that have registered for this service. adnAmMakeAccountingWindow is the time interval during which responses to these requests are accepted. adnAmMakeAccountingWindow is specified in units of seconds. Common Name: Make Acctg Window
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnAmAccountingFilePathName 3.1.637.3.1.5.11.1.7
The complete pathname of the current accounting file in the Network Management System directory which contains accounting data collected since the last posting. The complete pathname starts with and includes the root directory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnFmSaveCrucialAlarm 3.1.637.3.1.5.11.2.1
Indicates whether crucial alarms received from applications are saved in the alarm file. Common Name: Save Crucial Alarms
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnFmSaveAdminAlarm 3.1.637.3.1.5.11.2.2
Indicates whether administrative alarms received from applications are saved in the alarm file. Common Name: Save Admin Alarms
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFmSaveCriticalAlarm 3.1.637.3.1.5.11.2.3
Indicates whether critical alarms received from applications are saved in the alarm file. Common Name: Save Critical Alarms
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFmSaveMajorAlarm 3.1.637.3.1.5.11.2.4
Indicates whether major alarms received from applications are saved in the alarm file. Common Name: Save Major Alarms
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFmSaveMinorAlarm 3.1.637.3.1.5.11.2.5
Indicates whether minor alarms received from applications are saved in the alarm file. Common Name: Save Minor Alarms
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFmSaveTroubleAlarm 3.1.637.3.1.5.11.2.6
Indicates whether trouble alarms received from applications are saved in the alarm file. Common Name: Save Trouble Alarms
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFmSaveDiagnosticAlarm 3.1.637.3.1.5.11.2.7
Indicates whether diagnostic alarms received from applications are saved in the alarm file. Common Name: Save Diagnostic Alarms
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFmSaveClearedAlarm 3.1.637.3.1.5.11.2.8
Indicates whether cleared alarms received from applications are saved in the alarm file. Common Name: Save Cleared Alarms
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFmAlarmPostInterval 3.1.637.3.1.5.11.2.9
Defines a time period between transfers of the alarm file to the Network Management System directory. After each transfer, the Network Management System is also notified via a SNMP trap that this file is ready for transfer to the Network Management System via FTP services. Each posting contains only those alarms collected since the last posting. The unit of time for this interval is minutes. Common Name: Alarm Posting Interval
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnFmPostAlarm 3.1.637.3.1.5.11.2.10
When adnFmPostAlarm is enabled, the current file is transferred to the Network Management System directory and the Network Management System is subsequently notified via a SNMP trap that this file is ready for transfer to the Network Management System via FTP services. This file contains all alarms saved since the lasting posting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFmAlarmFilePathName 3.1.637.3.1.5.11.2.11
The complete pathname of the current alarm file in the Network Management System directory which contains all alarms collected since the last posting. The complete pathname starts with and includes the root directory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnPmHsEnableStats 3.1.637.3.1.5.11.3.1
Indicates whether historical statistics are collected and processed for all subscribing applications on the node by the Node Management Subsystem. Common Name: Historical Stats Collection
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnPmHsCollectInterval 3.1.637.3.1.5.11.3.2
Defines the time period between collections of historical statistics. The unit of time for this interval is minutes. Common Name: Historical Stat Collect Timer
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnPmHsPostInterval 3.1.637.3.1.5.11.3.3
Defines a time period between transfers of the historical statistics file to the Network Management System directory. After each transfer, the Network Management System is notified via a SNMP trap that this file is ready for transfer to the Network Management System via FTP services. Each posting contains only those historical statistics collected since the last posting. The unit of time for this interval is minutes. Common Name: Historical Stats Post Timer
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnPmHsPostStats 3.1.637.3.1.5.11.3.4
When adnPmHsPostStats is enabled, a file containing the current historical statistics is transferred to the Network Management System directory and the Network Management System is subsequently notified via a SNMP trap that this file is ready for transfer to the Network Management System via FTP services. This file contains all the historical statistics collected since the last posting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnPmHsMakeStats 3.1.637.3.1.5.11.3.5
When adnPmHsMakeStats is enabled, historical statistics from all applications that have registered for the service are requested and collected in a common statistics file. After waiting the time interval defined in adnPmHsMakeStatsWindow to receive all responses, the statistics file is transferred to the Network Management System directory and the Network Management System is notified via a SNMP trap that this file is ready for transfer to the Network Management System via FTP services.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnPmHsMakeStatsWindow 3.1.637.3.1.5.11.3.6
When adnPmHsMakeStats is enabled, historical statistics are requested from all applications that have registered for this service. adnPmHsMakeStatsWindow is the time interval during which responses to these requests are accepted. adnPmHsMakeStatsWindow is specified in units of seconds. Common Name: Make Historical Stats Window
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnPmHsFilePathName 3.1.637.3.1.5.11.3.7
The complete pathname of the current historical statistics file in the Network Management System directory which contains all historical statistics collected since the last posting. The complete pathname starts with and includes the root directory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnPmIsEnableStatsCollection 3.1.637.3.1.5.11.4.1
Indicates whether interval statistics are collected from all subscribing applications on the node by the Node Management Subsystem. Common Name: Interval Stats Collection
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnPmIsCurrentInterval 3.1.637.3.1.5.11.4.2
One of 96 discrete time intervals (or buckets) into which the interval statistics are being collected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnDumEnable 3.1.637.3.1.5.11.5.1
Enables and disables all Disk Utilization Management processing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnDumReduceExcessDiskStorage 3.1.637.3.1.5.11.5.2
Enables and disables all methods to reduce excessive disk storage in Disk Utilization Management managed filesystems. Methods of reduction consist of those defined by adnDumCyclicallyReduceExcess and adnDumImmediatelyReduceExcess. The Disk Utilization Management's managed filesystems are also defined in the adnDumGroup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnDumCyclicallyReduceExcess 3.1.637.3.1.5.11.5.3
Enables and disables the cyclical reduction of excess disk storage in Disk Utilization Management's managed filesytems. Disk Utilization Management's reduction process is an adjunct of its monitoring process. The periodicity of both processes is defined by adnDumMonitorInterval. The Disk Utilization Management's managed filesystems are also defined in adnDumGroup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnDumImmediatelyReduceExcess 3.1.637.3.1.5.11.5.4
Enables and disables the immediate reduction of excessive disk storage in Disk Utilization Management's managed filesystems. Independent of its monitoring cycle, Disk Utilization Management immediately reduces excessive disk storage. Once the excess storage is reduced, Disk Utilization Management effectively sets this object to disabled. The Disk Utilization Management's managed filesystems are also defined in the adnDumGroup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnDumFlagThresholdViolations 3.1.637.3.1.5.11.5.5
Enables and disables Disk Utilization Management's notification to the Network Management System of threshold violations from Disk Utilization Management's managed filesystems. Disk Utilization Management notifies the Network Management System via a Simple Network Management Protocol trap. The Disk Utilization Management's managed filesystems are also defined in the adnDumGroup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnDumFlagFileReady 3.1.637.3.1.5.11.5.6
Enables and disables Disk Utilization Management's notification to the Network Management System of overdue file retrievals from Disk Utilization Management's managed filesystems. If file retrievals are not completed within the limit, adnDumFileRetrievalTimeLimit, Disk Utilization Management considers the retrievals overdue and notifies the Network Management System via a Simple Network Management Protocol trap. The Disk Utilization Management's managed filesystems are also defined in the adnDumGroup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnDumLogEvents 3.1.637.3.1.5.11.5.7
Enables and disables Disk Utilization Management's maintenance of a history log file in which Disk Utilization Management events are recorded. The history log file is in an ASCII format.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnDumMonitorInterval 3.1.637.3.1.5.11.5.8
Defines the period of time between disk monitoring by Disk Utilization Management. The unit of time for this interval is seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnDumFileRetrievalTimeLimit 3.1.637.3.1.5.11.5.9
Defines the time period that Disk Utilization Management allows the Network Management System to retrieve files from Disk Utilization Management's managed filesystems, before determining that a reminder trap is required. The unit of time for this interval is seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnDumDirectoryTable 3.1.637.3.1.5.11.5.10
The Disk Utilization Management Directory Table defines the directories and subdirectories on which the filesytems that Disk Utilization Management manages are mounted. By default, the only filesystem monitored for disk utilization is /hss (which also contains /to_nms).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDumDirectoryEntry

adnDumDirectoryEntry 3.1.637.3.1.5.11.5.10.1
An entry in the Disk Utilization Management Directory Table that defines one directory and any subdirectories under the directory.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDumDirectoryEntry  

adnDumDirectoryIndex 3.1.637.3.1.5.11.5.10.1.1
Index to a table of directories on which Disk Utilization Management managed filesystems have been mounted.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnDumDirectoryPathname 3.1.637.3.1.5.11.5.10.1.2
The complete pathname to the directory on which a managed filesystem is mounted. The complete pathname starts with and includes the root directory. By default, the directory /hss is monitored. This includes the directory /to_nms.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnDumDirectoryPercentUsage 3.1.637.3.1.5.11.5.10.1.3
The percent of the aggregate disk storage that is used in the directory on which the filesystem is mounted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnPercent  

adnDumDirectoryLevelUsage 3.1.637.3.1.5.11.5.10.1.4
The level of usage of aggregate disk storage with respect to the three usage thresholds, low, medium and high, in the directory on which the filesystem is mounted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER belowLow(1), lowToMedium(2), mediumToHigh(3), abovehigh(4)  

adnDumUsageThresholds 3.1.637.3.1.5.11.5.10.1.5
A set of low, medium and high limits to the amount of the aggregate disk storage that is utilized in a managed filesystem. Each value represents a percentage of the whole amount that is allocated to the particular filesystem.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER low60med70high80(1), low70med80high90(2), low85med90high95(3), low90med95high99(4)  

adnDumSubdirectoryTable 3.1.637.3.1.5.11.5.11
The Disk Utilization Management Subdirectory Table defines the subdirectories under a Disk Utilization Management directory. A filesytem that Disk Utilization Management manages is mounted on the Disk Utilization Management directory. By default, the subdirectories under /hss which are monitored are: /hss/to_nms/perf (first priority is to delete old historical stats files.) /hss/to_nms/fault (second priority is to delete old alarm files.) /hss/to_nms/acct (third priority is to delete old accounting files, but only if the quota for accoutning is less than the default value of 100 percent.)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDumSubdirectoryEntry

adnDumSubdirectoryEntry 3.1.637.3.1.5.11.5.11.1
An entry in the Disk Utilization Management Subdirectory Table that defines one subdirectories under a Disk Utilization Management directory.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDumSubdirectoryEntry  

adnDumSubdirectoryIndex 3.1.637.3.1.5.11.5.11.1.1
Index to a table of subdirectories under a directory on which a Disk Utilization Management's managed filesystem has been mounted. The value of the index is directly related to order in which the subdirectories are targeted for storage reduction. The first subdirectory in the table of subdirectories that Disk Utilization Management targets for storage reduction has index 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnDumSubdirectoryPathname 3.1.637.3.1.5.11.5.11.1.2
The complete pathname to the subdirectory of a Disk Utilization Management directory. The complete pathname starts with and includes the root directory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnDumSubdirectoryQuota 3.1.637.3.1.5.11.5.11.1.3
The percent of the aggregate disk storage that is allocated to the subdirectory of the filesystem on which the parent directory is mounted. The default quota for the /hss/to_nms/perf subdirectory is 10 percent, meaning that on a first pass of the reduction cycle, old statistics files will be deleted until the /hss/to_nms/perf subdirectory is using no more than 10 percent of the total partition size. The default quota for the /hss/to_nms/fault subdirectory is 10 percent. The default quota for the /hss/to_nms/acct subdirectory is 100 percent, meaning that no accounting files will be deleted by this process.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnPercent  

adnUpdateCntlMIB 3.1.637.3.1.5.12
OBJECT IDENTIFIER    

adnUCNodeGroup 3.1.637.3.1.5.12.1
OBJECT IDENTIFIER    

adnUpdateCntl 3.1.637.3.1.5.12.2
OBJECT IDENTIFIER    

adnVerInfoGroup 3.1.637.3.1.5.12.3
OBJECT IDENTIFIER    

adnUCNodeAdminCommand 3.1.637.3.1.5.12.1.1
The NMS sets a command value into this object,as follows: NULL No action to take place. install Places newly-transferred files in a read- only partition. activate HSS sends code/configuration to subsystems. commit HSS declares the activated code/ configuration to be in committed state. deactivate Changes the state of the HSS by reverting to the committed code and configuration. withdraw Deletes installed files. confirm-link Set by the NMS following receipt of successful Activate trap. qInstallActivate Places newly-transferred Quick configuration change files in a secured partition and sends configuration to subsytems. qDeactivateWithdraw Undoes Quick configuration changes and deletes installed files. qConfirmChange Confirms a Quick configuration change and sets it as an extension of the committed version. qRebaseline Install and commit a new set of configuration files to synchronize the NMS and HSS after several Quick transactions. Common Name: Administrative Command
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER null(1), install(2), activate(3), commit(4), deactivate(5), withdraw(6), confirm-link(7), qInstallActivate(8), qDeactivateWithdraw(9), qConfirmChange(10), qRebaseline(11)  

adnUCNodeOperCommand 3.1.637.3.1.5.12.1.2
This object indicates the current or last command accepted and processed by the HSS. Common Name: Oper Command
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), install(2), activate(3), commit(4), deactivate(5), withdraw(6), none(7), qInstallActivate(8), qDeactivateWithdraw(9), qConfirmChange(10), qRebaseline(11)  

adnUCNodeOperStatus 3.1.637.3.1.5.12.1.3
This object notifies the NMS of the results of the last command, or if it is still in progress. Common Name: Oper Command Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-progress(1), success(2), failed(3), warning(4), rollback-in-progress(5), initial(6)  

adnUCNodeState 3.1.637.3.1.5.12.1.4
This object notifies the NMS of the `state' of code/ configuration update processing. The values are: committed -- The node is running the committed software version. activateInProgress -- An Activate command is in progress. uncommitted -- The node is running the uncommitted software version. activateInProgressSuspended -- An Activate command is in progress. The processing of the Activate is suspended while the Control Unit board waits for a confirmation that any coupler boards that have been reset have gone down, before Activate processing continues. loadingCommittedSuspended -- The node is in the process of loading the committed software version, due to a Deactivate command or an automatic rollback. The processing of the deactivation is suspended while the Control Unit board waits for a confirmation that any coupler boards that have been reset have gone down, before deactivation processing continues. loadingCommitted -- The node is in the process of loading the committed software version, due to a Deactivate command or an automatic rollback. qConfirmed -- The node is running a confirmed Quick configuration change on top of the committed version. qActivateInProgress -- A Quick Install&Activate command is in progress. qUnconfirmed -- The node is running the unconfirmed Quick configuration. qLoadingConfirmed -- The node is in the process of loading the confirmed Quick configuration, due to a Quick Deactivate&Withdraw command or an automatic rollback. qRebaselineInProgress -- A Quick Rebaseline command is in progress. Common name: Update Control Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER committed(0), activateInProgress(1), uncommitted(2), activateInProgressSuspended(3), loadingCommittedSuspended(4), loadingCommitted(5), qConfirmed(6), qActivateInProgress(7), qUnconfirmed(8), qLoadingConfirmed(9), qRebaselineInProgress(10)  

adnUCNodeErrorType 3.1.637.3.1.5.12.1.5
This object notifies the NMS of the type of error detected by the HSS configuration management. no-err -- There is no error config -- Error occurred in configuration file management software -- Error occurred in firmware or software management. Common Name: Update Error Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no-err(0), config(1), software(2)  

adnUCNodeErrorStatus 3.1.637.3.1.5.12.1.6
This object notifies the NMS of the exact error detected by the HSS configuration management. For configuration table errors, this is the SNMP error code defined in RFC 1448. For software or firmware management errors, the value is genErr(5). Common Name: Update Error Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noError(0), tooBig(1), noSuchName(2), badValue(3), readOnly(4), genErr(5), noAccess(6), wrongType(7), wrongLength(8), wrongEncoding(9), wrongValue(10), noCreation(11), inconsistentValue(12), resourceUnavailable(13), commitFailed(14), undoFailed(15), authorizationError(16), notWritable(17), inconsistentName(18)  

adnUCNodeErrorGroup 3.1.637.3.1.5.12.1.7
This object identifies the group in which this specific error code is defined. Typically, a group corresponds to one HSS software subsystem. Common Name: Update Error Group
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noError(0), sfas(1), nmgs(2), routes(3), cme(4), frs(5), isna(6), isom(7), llce(8), franpCm(9), franpSi(10), franpSw(11), ldFlip(12), ldQuicc(13), ldSpyder(14), smSup(15), mainSup(16), atmSup(17), atmLine(18), aafd(19), mainPmd(20), asm(21), aom(22), inmpLib(23), vs(24), pathSelect(25), routesAgt(26), atmCes(27), cvsi(28), iprt(29)  

adnUCNodeErrorCode 3.1.637.3.1.5.12.1.8
This object identifies a specific error defined within a group. Its interpretation depends on the value of adnUCNodeErrorGroup. Common Name: Update Error Code
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnUCNodeExceptionCode 3.1.637.3.1.5.12.1.9
This object identifies an exception condition, if an error was detected during configuration table processing (adnUCNodeErrorType = config). Values may be zero (no exception), 0x80 (no such object) or 0x81 (no such instance). Common Name: Update Exception Code
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnUCNodeErrorChassis 3.1.637.3.1.5.12.1.10
This object identifies the chassis for which the error occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnUCNodeErrorSlot 3.1.637.3.1.5.12.1.11
This object identifies the slot for which the error occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnUCNodeErrorProc 3.1.637.3.1.5.12.1.12
This object identifies the processor for which the error occurred, in the case of software or firmware management errors (adnUCNodeErrorType = software).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnUCNodeErrorTableName 3.1.637.3.1.5.12.1.13
This object identifies the MIB table name for which the error occurred, in the case of configuration table errors (adnUCNodeErrorType = config).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnUCNodeErrorIndex1 3.1.637.3.1.5.12.1.14
This object identifies the first index value of the table instance for which the error occurred, in the case of configuration table errors (adnUCNodeErrorType = config). It is zero if it does not apply, or if it cannot be represented as an integer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnUCNodeErrorIndex2 3.1.637.3.1.5.12.1.15
This object identifies the second index value of the table instance for which the error occurred, in the case of configuration table errors (adnUCNodeErrorType = config). It is zero if it does not apply, or if it cannot be represented as an integer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnUCNodeErrorIndex3 3.1.637.3.1.5.12.1.16
This object identifies the third index value of the table instance for which the error occurred, in the case of configuration table errors (adnUCNodeErrorType = config). It is zero if it does not apply, or if it cannot be represented as an integer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnUCNodeErrorIndex4 3.1.637.3.1.5.12.1.17
This object identifies the fourth index value of the table instance for which the error occurred, in the case of configuration table errors (adnUCNodeErrorType = config). It is zero if it does not apply, or if it cannot be represented as an integer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnUCNodeErrorNominator 3.1.637.3.1.5.12.1.18
This object identifies the nominator for which the error occurred, in the case of configuration table errors (adnUCNodeErrorType = config).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnUCNodeUncommittedAvail 3.1.637.3.1.5.12.1.19
This object indicates whether there is an uncommitted version installed. The values are: available -- There is a uncommitted version installed. unavailable -- There is no uncommitted version installed. Common Name: Uncommitted Version
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(0), available(1), unavailable(2)  

adnUCNodeDeliveryType 3.1.637.3.1.5.12.1.20
The type of delivery made by the NMS to the HSS. SingleReplacement means that the entire software version for the HSS is being delivered, and should replace unconditionally whatever is the current software version running at the HSS. SingleModification means that the delivery from the NMS may be full or partial, and that the HSS will detect which files have changed between the current HSS software version and the new delivery. For both singleReplacement and singleModification, there is just one single delivery tar file from the NMS, not multiple tar files.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER singleModification(1), singleReplacement(2)  

adnUCNodeDebugCommand 3.1.637.3.1.5.12.1.21
This object is used by a network operator to enable the capture of configuration management trace information into an ASCII file, which may then be retrieved and analyzed off-line. Setting the value of this object to startTrace causes the HSS to begin saving the detailed trace of the Node Configuration Management Subsystem into the memory of the HSS Control Unit. Setting the value of this object to saveTrace causes the detailed trace of the Node Configuration Management Subsystem to be copied from HSS memory into a file stored on the HSS Control Unit disk, in /hss_pmd/.nmcm_detail_trace. The file is a snapshot of the current trace in memory. Its maximum size is 500,000 bytes. If a previous snapshot already existed in the directory /hss_pmd, then this old file is renamed to /hss_pmd/.old.nmcm_detail_trace. (A third trace file, .auto_nmcm_detail_trace, may also be present in the same directory. This contains a snapshot of the trace in memory that is saved to disk automatically in the event of an internally-detected error condition or version deactivation.) Setting the value of this object to stopTrace causes the HSS to stop saving the detailed trace into memory. NoCommand is the default value of this object, and has no effect on the node.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noCommand(1), startTrace(2), saveTrace(3), stopTrace(4)  

adnUCNodeCodeFlashFlag 3.1.637.3.1.5.12.1.22
This object is used by a network operator to enable or disable the code downloading from coupler flash. The values are: disableFlash - code will be neither programmed in flash (either on-line or off-line) nor loaded from flash. offLineFlashOnly - only off-line flash update is allowed. Code can be loaded from flash. enableFlash - code can be programmed in flash (either on-line or off-line) and loaded from flash.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disableFlash(1), offLineFlashOnly(2), enableFlash(3)  

adnUCNodeConfigFlashFlag 3.1.637.3.1.5.12.1.23
This object is used by a network operator to enable or disable the configuration downloading from coupler flash. The values are: disableFlash - the configuration will be neither programmed in flash (either on-line or off-line) nor loaded from flash. offLineFlashOnly - only off-line flash update is allowed. The configuration can be loaded from flash. enableFlash - the configuration can be programmed in flash (either on-line or off-line) and loaded from flash.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disableFlash(1), offLineFlashOnly(2), enableFlash(3)  

adnCuCodeUpdateCntlTable 3.1.637.3.1.5.12.2.2
The Control Unit Update Control table contains objects for Control Unit code operational status between the HSS and the NMS.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCuCodeUpdateCntlEntry

adnCuCodeUpdateCntlEntry 3.1.637.3.1.5.12.2.2.1
An entry in the Control Unit code portion of the Update Control table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnCuCodeUpdateCntlEntry  

adnCuCodeServiceIdIndex 3.1.637.3.1.5.12.2.2.1.1
Index field. The value of a Control Unit service.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), core-complement(2)  

adnCuCodeOperStatus 3.1.637.3.1.5.12.2.2.1.2
This object notifies the NMS of the results of the last command, or whether it is still in progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-progress(1), success(2), failed(3), pending(4)  

adnCuCodeState 3.1.637.3.1.5.12.2.2.1.3
This object notifies the NMS of the `state' of Control Unit code update processing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER committed(1), uncommitted(2)  

adnCuConfigUpdateCntlTable 3.1.637.3.1.5.12.2.3
The Configuration Update Control table contains objects for Control Unit Configuration operational status between the HSS and the NMS.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCuConfigUpdateCntlEntry

adnCuConfigUpdateCntlEntry 3.1.637.3.1.5.12.2.3.1
An entry in the Control Unit Configuration Update Control table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnCuConfigUpdateCntlEntry  

adnCuConfigApplIdIndex 3.1.637.3.1.5.12.2.3.1.1
Index field - Control Unit application IDs (e.g. NMGS, SFAS, Main Supervisor, ....)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER sfas-id(1), nmgs-id(2), msup-id(3), iss-id(4), pmd-id(5), routes-id(6), mibmgt-id(7), iprt-id(8)  

adnCuConfigOperStatus 3.1.637.3.1.5.12.2.3.1.2
This object notifies the NMS of the results of the last command, or whether it is still in progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-progress(1), success(2), failed(3), pending(4)  

adnCuConfigState 3.1.637.3.1.5.12.2.3.1.3
This object notifies the NMS of the `state' of Control Unit configuration update processing. The values mean: committed -- This CU application is not currently loading configuration tables. Its configuration tables are from the committed version. actInProgWaitingForLoadInd -- An Activate command is in progress, and for this CU application, the state machine is waiting for an indication that a request has been received to start loading the tables. actInProgMiddleTransaction -- An Activate command is in progress, and for this CU application, the state machine is waiting for the response to a middle message within a configuration transaction. actInProgEndTransaction -- An Activate command is in progress, and for this CU application, the state machine is waiting for the response to a null message that signals the end of a a configuration transaction. uncommitted -- This CU application is using uncommitted configuration tables. loadingCommittedNextFile -- This CU application is the the process of loading uncommitted configuration tables. The state machine is waiting for a response to a null message that signals the end of a transaction, and will then send the next configuration file, which will be the rollback file. loadingCommittedMiddleTrans -- This CU application is the the process of loading committed configuration tables. The state machine is waiting for a response to a middle message within the configuration transaction. loadingCommittedEndTrans -- This CU application is the the process of loading committed configuration tables. The state machine is waiting for a response to a null message that signals the end of a transaction.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER committed(0), actInProgWaitingForLoadInd(1), actInProgMiddleTransaction(2), actInProgEndTransaction(3), uncommitted(4), loadingCommittedNextFile(5), loadingCommittedMiddleTrans(6), loadingCommittedEndTrans(7)  

adnCuConfigFileName 3.1.637.3.1.5.12.2.3.1.4
This object identifies the configuration file to be used for this Control Unit subsystem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnCuConfigNextFileName 3.1.637.3.1.5.12.2.3.1.5
This object identifies the next configuration file to be used for this Control Unit subsystem, if there is an automatic rollback in progress from uncommitted configuration to committed configuration. The value of this object is not significant if there is currently no rollback in progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnProcCodeUpdateCntlTable 3.1.637.3.1.5.12.2.4
The Update Control table contains objects for processor code operational status between the HSS and the NMS.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnProcCodeUpdateCntlEntry

adnProcCodeUpdateCntlEntry 3.1.637.3.1.5.12.2.4.1
An entry in the processor code portion of the Update Control table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnProcCodeUpdateCntlEntry  

adnProcCodeChassisIndex 3.1.637.3.1.5.12.2.4.1.1
Index field that identifies the chassis. Chassis are numbered 1-7. The main chassis (i.e., the one with the active Control Unit) in a multi-chassis node is chassis number 1. In a single-chassis node, the chassis number is 1. This number is provided in hardware by a HLCID card which is plugged into the midplane.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnProcCodeSlotIndex 3.1.637.3.1.5.12.2.4.1.2
Index field that identifies the slot. Slots within a chassis are numbered 1-12. The first slot on the left when facing the front of the chassis is number 1. This number is provided in hardware through hard-wiring on the midplane. Note that the HBSAC board always has a special slot identifier of 30, but this slot number is never used.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnProcCodeProcessorIndex 3.1.637.3.1.5.12.2.4.1.3
Index field that identifies the processor on a coupler board. Processors on a coupler are numbered 0-3. The number of processors varies depending on the type of coupler.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnProcCodeOperStatus 3.1.637.3.1.5.12.2.4.1.4
This object notifies the NMS of the results of the last command, or whether it is still in progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-progress(1), success(2), failed(3), pending(4)  

adnProcCodeState 3.1.637.3.1.5.12.2.4.1.5
This object notifies the NMS of the `state' of processor code update processing. The values are: committed -- This processor is not in the process of loading, and the software for this processor is the committed version. actInProgWaitForDownMsg -- An Activate command is in progress, this processor has been reset, and the state machine is waiting for a message confirming that the processor is now down. actInProgWaitForReloadReq -- An Activate command is in progress, this processor has already loaded at least once and then started to reload. The state machine is waiting for another load request. actInProgWaitForSwCompleteMsg -- An Activate command is in progress, and the state machine is waiting for a message to indicate that the software portion of the load has completed. uncommitted -- This processor is not in the process of loading. It is currently running uncommitted software. loadCommittedWaitForDownMsg -- This processor is in the process of loading committed software. The processor has been reset, and the state machine is waiting for a message confirming that the processor is down. loadCommittedWaitForCompleteMsg -- This processor is in the process of loading committed software. The state machine is waiting for a message to indicate that the load has completed. pending -- An Activate command is in progress, and this processor is currently down. When the processor comes up, it will be loaded with the uncommitted software version. actInProgWaitForFwareCompleteMsg -- An Activate command is in progress, and the state machine is waiting for a message to indicate that the firmware portion of the load has completed. actInProgWaitForFlashCompleteMsg -- An Activate command is in progress, and the state machine is waiting for a message to indicate that the update of code into flash memory has completed. actInProgWaitForLoadRequest -- An Activate command is in progress, and this processor has been reset. The state machine is waiting for a request to start the loading process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER committed(0), actInProgWaitForDownMsg(1), actInProgWaitForReloadReq(2), actInProgWaitForSwCompleteMsg(3), uncommitted(4), loadCommittedWaitForDownMsg(5), loadCommittedWaitForCompleteMsg(6), pending(7), actInProgWaitForFwareCompleteMsg(8), actInProgWaitForFlashCompleteMsg(9), actInProgWaitForLoadRequest(10)  

adnBrdConfigUpdateCntlTable 3.1.637.3.1.5.12.2.5
The board configuration portion of the Update Control table contains objects for board configuration operational status between the HSS and the NMS.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnBrdConfigUpdateCntlEntry

adnBrdConfigUpdateCntlEntry 3.1.637.3.1.5.12.2.5.1
An entry in the board configuration portion of the Update Control table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnBrdConfigUpdateCntlEntry  

adnBrdConfigChassisIndex 3.1.637.3.1.5.12.2.5.1.1
Index field that identifies the chassis. Chassis are numbered 1-7. The main chassis (i.e., the one with the active Control Unit) in a multi-chassis node is chassis number 1. In a single-chassis node, the chassis number is 1. This number is provided in hardware by a HLCID card which is plugged into the midplane.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnBrdConfigSlotIndex 3.1.637.3.1.5.12.2.5.1.2
Index field that identifies the slot. Slots within a chassis are numbered 1-12. The first slot on the left when facing the front of the chassis is number 1. This number is provided in hardware through hard-wiring on the midplane. Note that the HBSAC board always has a special slot identifier of 30, but this slot number is never used.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnBrdConfigOperStatus 3.1.637.3.1.5.12.2.5.1.3
This object notifies the NMS of the results of the last command, or whether it is still in progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-progress(1), success(2), failed(3), pending(4)  

adnBrdConfigState 3.1.637.3.1.5.12.2.5.1.4
This object notifies the NMS of the `state' of configuration update processing. The values mean: committed -- This board is not currently loading configuration tables. Its configuration tables are from the committed version. actInProgWaitingForLoadInd -- An Activate command is in progress. For this board, the state machine is waiting for an indication that all requests to load tables have been received, so that the loading can begin. actInProgMiddleTransaction -- An Activate command is in progress, and for this board, the state machine is waiting for the response to a middle message within a configuration transaction. actInProgEndTransaction -- An Activate command is in progress, and for this board, the state machine is waiting for the response to a null message that signals the end of a configuration transaction. uncommitted -- This board is using uncommitted configuration tables. loadingCommittedNextFile -- This board is in the process of loading uncommitted configuration tables. The state machine is waiting for a response to a null message that signals the end of a transaction, and will then send the next configuration file, which will be the rollback file. loadingCommittedMiddleTrans -- This board is in the process of loading committed configuration tables. The state machine is waiting for a response to a middle message within the configuration transaction. loadingCommittedEndTrans -- This board is in the process of loading committed configuration tables. The state machine is waiting for a response to a null message that signals the end of a transaction. pending -- An Activate command is in progress, and this board is currently down. When the board comes up, it will be loaded with the uncommitted configuration file.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER committed(0), actInProgWaitingForLoadInd(1), actInProgMiddleTransaction(2), actInProgEndTransaction(3), uncommitted(4), loadingCommittedNextFile(5), loadingCommittedMiddleTrans(6), loadingCommittedEndTrans(7), pending(8)  

adnBrdConfigFileName 3.1.637.3.1.5.12.2.5.1.5
This object identifies the configuration file being used for this board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnBrdConfigNextFileName 3.1.637.3.1.5.12.2.5.1.6
This object identifies the next configuration file to be used for this board, if there is an automatic rollback in progress from uncommitted configuration to committed configuration. The value of this object is not significant if there is currently no rollback in progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnBrdConfigNoCfgOrFullCfg 3.1.637.3.1.5.12.2.5.1.7
This object identifies whether a Parameteric File Xfer Interface (PFXI) configuration file exists for this chassis and slot. The values mean: noConfig -- no configuration file fullConfig -- full configuration file deletedConfig -- the board has been deleted. For some board types (such as High Speed Couplers), the configuration parameters are managed entirely by the Control Unit, not by the software running on the board itself. In these cases there will be no configuration file. When a coupler board has been deleted from the uncommitted version, but still exists in the committed version, the value of this object is set to deletedConfig.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noConfig(1), fullConfig(2), deletedConfig(3)  

adnBrdFlashContentListTable 3.1.637.3.1.5.12.2.6
The board flash content list is a portion of the Update Control group which contains information about the contents of a board's flash memory.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnBrdFlashContentListEntry

adnBrdFlashContentListEntry 3.1.637.3.1.5.12.2.6.1
An entry in the board flash content portion of the Update Control table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnBrdFlashContentListEntry  

adnBrdFlashChassisIndex 3.1.637.3.1.5.12.2.6.1.1
Index field that identifies the chassis. Chassis are numbered 1-7. The main chassis (i.e., the one with the active Control Unit) in a multi-chassis node is chassis number 1. In a single-chassis node, the chassis number is 1. This number is provided in hardware by a HLCID card which is plugged into the midplane.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnBrdFlashSlotIndex 3.1.637.3.1.5.12.2.6.1.2
Index field that identifies the slot. Slots within a chassis are numbered 1-12. The first slot on the left when facing the front of the chassis is number 1. This number is provided in hardware through hard-wiring on the midplane. Note that the HBSAC board always has a special slot identifier of 30, but this slot number is never used.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnBrdFlashSize 3.1.637.3.1.5.12.2.6.1.3
This object identifies the coupler board flash size in megabytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnBrdFlashVolume1 3.1.637.3.1.5.12.2.6.1.4
This object identifies the flash image file name loaded in the first volume of coupler flash.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnBrdFlashVolume2 3.1.637.3.1.5.12.2.6.1.5
This object identifies the flash image file name loaded in the second volume of coupler flash.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnBrdFlashVolume3 3.1.637.3.1.5.12.2.6.1.6
This object identifies the flash image file name loaded in the third volume of coupler flash.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnBrdFlashVolume4 3.1.637.3.1.5.12.2.6.1.7
This object identifies the flash image file name loaded in the fourth volume of coupler flash.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnVerInfoNodeGroup 3.1.637.3.1.5.12.3.1
OBJECT IDENTIFIER    

adnNodeRunningVersion 3.1.637.3.1.5.12.3.1.1
This object identifies the pathname of the node-level version descriptor file for the HSS software version that is currently running. The format of the filename is vd.., where is the HSS software version number and is the value modulo 100 of the NMS configuration number, which is incremented at the NMS whenever a new HSS software and/or configuration package is built. is the product release number (1 digit, 0-9), is the functional version (1 digit, 0-9), is the sub-function version within the release (2 digits, 00-99), is the fix version number, (2 digits, 01-99), and is a number that the Network Management System assigns to insure uniqueness of the version number, (2 digits, 00-99).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnNodeCommittedVersion 3.1.637.3.1.5.12.3.1.2
This object identifies the pathname of the node-level version descriptor file for the committed (validated) HSS software version. The format of the filename is vd.., where is the HSS software version number and is the value modulo 100 of the NMS configuration number, which is incremented at the NMS whenever a new HSS software and/or configuration package is built. is the product release number (1 digit, 0-9), is the functional version (1 digit, 0-9), is the sub-function version within the release (2 digits, 00-99), is the fix version number, (2 digits, 01-99), and is a number that the Network Management System assigns to insure uniqueness of the version number, (2 digits, 00-99).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnNodeUncommittedVersion 3.1.637.3.1.5.12.3.1.3
This object identifies the pathname of the node-level version descriptor file for the uncommitted (non-validated) HSS software version. The format of the filename is vd.., where is the HSS software version number and is the value modulo 100 of the NMS configuration number, which is incremented at the NMS whenever a new HSS software and/or configuration package is built. is the product release number (1 digit, 0-9), is the functional version (1 digit, 0-9), is the sub-function version within the release (2 digits, 00-99), is the fix version number, (2 digits, 01-99), and is a number that the Network Management System assigns to insure uniqueness of the version number, (2 digits, 00-99). If there is no uncommitted software version, then a null string is returned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnNodeNMSCommitNumber 3.1.637.3.1.5.12.3.1.4
This object is the NMS configuration number of the HSS version (software and configuration package) which is committed at the HSS. It is set by the NMS as part of the commit procedure.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnNodeNMSBuildNumber 3.1.637.3.1.5.12.3.1.5
This object is the NMS configuration number of the HSS version (software and configuration package) which is transferred to and activated at the HSS. It is set by the NMS right after the install procedure.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnNodeNMSQbuildNumber 3.1.637.3.1.5.12.3.1.6
This object is the NMS configuration number of the HSS configuration version built using the Quick interface which is transferred to and activated at the HSS. It is incremented by the NMS after each qConfirm command, and reset after each qRebaseline command.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adn3rdPartyMIB 3.1.637.3.1.5.13
OBJECT IDENTIFIER    

adn3rdPartyCardTable 3.1.637.3.1.5.13.1
A list of third party card entries and attributes needed by network management. This is an extension to the adnEquipTable for third party card entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Adn3rdPartyCardEntry

adn3rdPartyCardEntry 3.1.637.3.1.5.13.1.1
A card entry containing objects that represent the access address and parameters that can be displayed in the NMS.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Adn3rdPartyCardEntry  

adn3rdPartyCardDescr 3.1.637.3.1.5.13.1.1.1
A textual string describing the card. Common Name: Description
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adn3rdPartyCardLocAddrType 3.1.637.3.1.5.13.1.1.2
Card's address type. Common Name: Address Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), ip(2), e164(3), x121(4), private(5)  

adn3rdPartyCardLocAddress 3.1.637.3.1.5.13.1.1.3
Address of card. Common Name: Address
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

adnClock 3.1.637.3.1.5.14
OBJECT IDENTIFIER    

adnClockConfigTable 3.1.637.3.1.5.14.1
The system clock configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnClockConfigEntry

adnClockConfigEntry 3.1.637.3.1.5.14.1.1
An entry in the system clock configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnClockConfigEntry  

adnClockIfIndex 3.1.637.3.1.5.14.1.1.1
The value of this object corresponds to the ifIndex and it uniquely identifies a DS1/E1 line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnClockType 3.1.637.3.1.5.14.1.1.2
This object defines the type of DS1/E1 line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER primary(1), backup(2)  

adnClockStatus 3.1.637.3.1.5.14.1.1.3
The system clock status can be determined by looking at this object for both the primary and backup lines. If the status is failed for both lines, it implies that the system timing is provided by a local clock. If the status is failed in the primary line and good in the backup line, it implies that the system timing is provided by the backup line. If the status is good in the primary line, it implies that the system timing is provided by the primary line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER good(1), failed(2)  

adnClockSource 3.1.637.3.1.5.14.1.1.4
The system clock source is typically derived from the line(1). In a network with no other suitable clock source, one HSS can be designated as the clock source for the entire network. That HSS would be configured as internal(2) for its primary and backup. All other HSS in the network would still use the value line(1).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER line(1), internal(2)  

adnUCNodeErrorsMsup 3.1.637.3.1.9.1.16
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupInconsTran 3.1.637.3.1.9.1.16.1
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupInconsIndex 3.1.637.3.1.9.1.16.2
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupMissingObject 3.1.637.3.1.9.1.16.3
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupBoardCrash 3.1.637.3.1.9.1.16.4
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupCu1NotConf 3.1.637.3.1.9.1.16.6
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupCu2NotConf 3.1.637.3.1.9.1.16.7
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupCuInWrongSlot 3.1.637.3.1.9.1.16.8
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupNotCuSlot 3.1.637.3.1.9.1.16.9
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupSoftwareError 3.1.637.3.1.9.1.16.10
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupCuNotSuspend 3.1.637.3.1.9.1.16.11
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupActionAlreadyProgress 3.1.637.3.1.9.1.16.12
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupVersionChangeProgress 3.1.637.3.1.9.1.16.13
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupInconsCuTypes 3.1.637.3.1.9.1.16.14
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupWrongCu1Type 3.1.637.3.1.9.1.16.15
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupWrongCu2Type 3.1.637.3.1.9.1.16.16
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupWrongCu1ApplType 3.1.637.3.1.9.1.16.17
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupWrongCu2ApplType 3.1.637.3.1.9.1.16.18
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupWrongSyncConf 3.1.637.3.1.9.1.16.19
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupCuForbidSwitch 3.1.637.3.1.9.1.16.20
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupInconsState 3.1.637.3.1.9.1.16.141
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupCUModif 3.1.637.3.1.9.1.16.142
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupWrongAppl 3.1.637.3.1.9.1.16.143
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupWrongRedunRole 3.1.637.3.1.9.1.16.145
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupWrongRedunOptions 3.1.637.3.1.9.1.16.146
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupWrongServInd 3.1.637.3.1.9.1.16.151
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupWrongAseConf 3.1.637.3.1.9.1.16.152
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupProcCreation 3.1.637.3.1.9.1.16.155
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupISLBlock 3.1.637.3.1.9.1.16.156
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupISLUnblock 3.1.637.3.1.9.1.16.157
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupISLReset 3.1.637.3.1.9.1.16.158
OBJECT IDENTIFIER    

adnUCNodeErrorsMsupSLLReq 3.1.637.3.1.9.1.16.159
OBJECT IDENTIFIER    

adnNodeSupervisionMIB 3.1.637.3.1.5.15
OBJECT IDENTIFIER    

adnChassisTable 3.1.637.3.1.5.15.1
This is the chassis table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnChassisEntry

adnChassisEntry 3.1.637.3.1.5.15.1.1
An entry in the chassis table. There is one entry for each chassis. The index corresponds to equipment type 'chassis' in the adnEquipTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnChassisEntry  

adnChassisStatus 3.1.637.3.1.5.15.1.1.1
This variable indicates the chassis status. It is a bit map represented as a sum; therefore, it can represent multiple failures. The bit positions are: 1 : power supply failure 4 : fan failure 8 : temperature warning 16 : SAC card (Status and Alarm Control) failure 32 : ISL (Internal Serial Link) bus failure detected on the active CU 64 : IOS (Input Output Service) bus failure detected on the active CU 128 : IOS (Input Output Service) bus silence detected on the active CU 256 : ISL (Internal Serial Link) bus state unknown on the active CU 512 : IOS (Input Output Service) bus state unknown on the active CU N.B.: This variable is significant when the operational state of the chassis is disabled. When there is no chassis error, this variable has the value 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisOperFanId 3.1.637.3.1.5.15.1.1.2
This variable identifies the fan trays which are operational. It is a bit map represented as a sum; therefore, it can represent multiple fan trays in the operational state. Each bit position represents a fan tray. If the bit is set, the fan tray is operational. If the bit is not set, the fan tray is not operational. The bit positions are: 1 : Fan tray number 1 is operational 2 : Fan tray number 2 is operational Note: This information is not significant if the fan tray is not present in the chassis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisPresentFanId 3.1.637.3.1.5.15.1.1.3
This variable identifies the fan trays which are present in the chassis. It is a bit map represented as a sum; therefore it can represent multiple fan trays in the chassis. Each bit position represents a fan tray. If the bit is set, the fan tray is present. If the bit is not set, the fan tray is absent. The bit positions are: 1 : Fan tray number 1 is present 2 : Fan tray number 2 is present.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisOperPowerId 3.1.637.3.1.5.15.1.1.4
This variable identifies the power supplies which are operational. It is a bit map represented as a sum; therefore, it can represent multiple power supplies in the operational state. Each bit position represents a power supply. If the bit is set, the power supply is operational. If the bit is not set, the power supply is not operational. The bit positions are: 1 : Power supply number 1 is operational 2 : Power supply number 2 is operational 4 : Power supply number 3 is operational 8 : Power supply number 4 is operational 16 : Power supply number 5 is operational 32 : Power supply number 6 is operational. Note: This information is not significant if the power supply is not present in the chassis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisPresentPowerId 3.1.637.3.1.5.15.1.1.5
This variable identifies the power supplies which are present in the chassis. It is a bit map represented as a sum; therefore, it can represent multiple power supplies in the chassis. Each bit position represents a power supply. If the bit is set, the power supply is present. If the bit is not set, the power supply is absent. The various bit positions are: 1 : Power supply number 1 is present 2 : Power supply number 2 is present 4 : Power supply number 3 is present 8 : Power supply number 4 is present 16 : Power supply number 5 is present 32 : Power supply number 6 is present.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisSlotNumber 3.1.637.3.1.5.15.1.1.6
This variable indicates the number of slots in the chassis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisPrimaryMSC8kSourceIfIndex 3.1.637.3.1.5.15.1.1.7
This variable identifies the master line timing source . In spite of the name, which is like this for historical reasons, the line timing source can be MSC (Medium Speed Coupler) 8kHz, PDH HSC (High Speed Coupler) or SDH HSC line timing source. The value of this object corresponds to the ifIndex of the line which provides the source. The value 0 is used when there is no master line timing source located on the chassis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisBackupMSC8kSourceIfIndex 3.1.637.3.1.5.15.1.1.8
This variable identifies the backup line timing source . In spite of the name, which is like this for historical reasons, the line timing source can be MSC (Medium Speed Coupler) 8kHz, PDH HSC (High Speed Coupler) or SDH HSC line timing source. The value of this object corresponds to the ifIndex of the line which provides the source. The value 0 is used when there is no backup line timing source located on the chassis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisMidplaneClockStatus 3.1.637.3.1.5.15.1.1.9
This object provides the status of the reference clocks on the chassis midplane. It is a bit map and a set bit indicates clock presence. The bit positions refer to the following clock references: 1 - primary 8 kHz MSC (Medium Speed Coupler) - (H80B) 2 - backup 8 kHz MSC - (H81B) 4 - primary SDH (Synchronous Digital Hierarchy) 8 - backup SDH 16 - primary PDH (Plesiochronous Digital Hierarchy) 32 - backup PDH In a multi-chassis system, a value of 0 indicates that all clock references are down. In a single-chassis system, the value of this object is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisClockPropagationStatus 3.1.637.3.1.5.15.1.1.10
This object provides the status of the clock propagated from this chassis to the next. It is a bit map and a set bit indicates that the clock is present. 1 - primary 8 kHz MSC (Medium Speed Coupler) 2 - backup 8 kHz MSC 4 - primary line timing (LT0) 8 - backup line timing (LT1) 16 - primary SDH (Synchronous Digital Hierarchy) 32 - backup SDH 64 - primary PDH (Plesiochronous Digital Hierarchy) 128 - backup PDH A value of 0 indicates that no clocks are being propagated. Note that the value of this object is 0 for a single-chassis system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisRABUsage 3.1.637.3.1.5.15.1.1.11
This variable indicates the slot number of the primary card which uses the RAB ( Redundancy Applique Bus). The value zero indicates that the RAB is not used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnChassisStandbyCUBusStatus 3.1.637.3.1.5.15.1.1.12
This variable indicates the failures of the busses connected between the chassis and the standby CU ( Control Unit) card. It is a bit map represented as a sum; therefore it can represent multiple failures. The value zero indicates that there is no failure. The bit positions are : 32 : ISL (Internal Serial Link) bus failure detected on the standby CU 64 : IOS (Input Output Service) bus failure detected on the standby CU 128 : IOS (Input Output Service) bus silence detected on the standby CU 256 : ISL (Internal Serial Link) bus state unknown on the standby CU 512 : IOS (Input Output Service) bus state unknown on the standby CU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnBoardTable 3.1.637.3.1.5.15.2
This table is the board table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnBoardEntry

adnBoardEntry 3.1.637.3.1.5.15.2.1
An entry in the board table. There is one entry for each board configured. The index corresponds to equipment type 'card' in the adnEquipTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnBoardEntry  

adnBoardAppliqueType 3.1.637.3.1.5.15.2.1.3
This indicates the configured applique type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAppliqueType  

adnBoardAppliqueState 3.1.637.3.1.5.15.2.1.4
This indicates the operational state of an applique which is either present or absent or wrong or inaccessible. The value inaccessible is used when the board is absent and its applique can not be detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), absent(2), wrong(3), inaccessible(4)  

adnBoardApplPluggedType 3.1.637.3.1.5.15.2.1.5
This indicates the type of applique that is plugged in.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAppliqueType  

adnBoardPluggedType 3.1.637.3.1.5.15.2.1.6
This indicates the type of board that is plugged in. If no board is plugged in, this MIB object value should is set to the OBJECT IDENTIFIER { 0 0 }.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AutonomousType  

adnBoardRedundancyRole 3.1.637.3.1.5.15.2.1.7
This indicates the redundancy role of the card. A value of noRedundancy(1) is used for cards that do not support redundancy. Cards that support redundancy, but do not have a spare configured have a value of primary(2). For the CU (Control Unit) board, this object is not significant and its value is always zero. value state ----- ------------------ 0 not significant ( for CU board). 1 this card does not support redundancy. 2 primary : this card can be backed up by another board in case of failure. 3 spare : the card can back up another card in case of failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(0), noRedundancy(1), primary(2), spare(3)  

adnBoardRedundancyStatus 3.1.637.3.1.5.15.2.1.8
This indicates the redundancy status of the card. A card that does not support redundancy is considered a primary running for itself. For the CU (Control Unit) board, this object is not significant and its value is always zero. value status ----- ------------------ 0 not significant ( for CU board). 1 this card is a primary running for itself. 2 this card is an idle spare. 3 this card is a spare card running in place of a primary card. 4 a switchover to spare is in progress. 5 a switchback to primary is in progress. 6 the card is a primary card that is not running; a spare is running in its place.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(0), runningAsPrimary(1), idleSpare(2), runningAsBackup(3), switchoverInProgress(4), switchbackInProgress(5), runningOnBackup(6)  

adnBoardRedundancyFailure 3.1.637.3.1.5.15.2.1.9
The value of this object is a bitmap that qualifies the switchover or the switchback failures. When the value of this object is 0, none of the failures is present. For the CU (Control Unit) board, this object is not significant and its value is always zero. bit position failure ------------ ------------------ 0 no failure 1 the primary card is not available for the switchback 2 no spare card is available for the switchover 4 RAB (Redundancy Applique Bus) busy : see adnChassisRABUsage in adnChassisTable 8 the applique switchover from the primary card to the spare card has failed
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnBoardRedundantBind 3.1.637.3.1.5.15.2.1.10
For a primary card, this variable indicates the adnEquipIndex of the spare card which backs up this primary card. For a spare card, this variable indicates the adnEquipIndex of the primary card which is backed up by this spare card. The value zero indicates no relationship. For the CU (Control Unit) board, this object is not significant and its value is always zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnBoardSwitchCause 3.1.637.3.1.5.15.2.1.11
The value of this object gives the reason why the switchover or the switchback has been initiated. This object qualifies the object adnBoardRedundancyFailure. For the CU (Control Unit) board, this object is not significant and its value is always zero. value cause ----- ------------------ 0 not significant ( for CU board) 1 neither switchover nor switchback occurred 2 manual switchover 3 automatic switchover 4 manual switchback 5 semiautomatic switchback 6 automatic switchback
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(0), noSwitch(1), manualSwitchover(2), automaticSwitchover(3), manualSwitchback(4), semiautomaticSwitchback(5), automaticSwitchback(6)  

adnBoardFaultStatus 3.1.637.3.1.5.15.2.1.12
For values 1 to 8 : this variable gives details on transitory failures of a CU (Control Unit) card. Other values : this variable gives details on failures on signals from or to a BBSYN card. For the other cards, this variable is not significant; see adnEquipTrapCause to know the reason of the last failure. The value zero indicates that there is no such type of failure. value failure ----- ------------------ 1 : Hardware problem on one LSN link (Local Sub-Network). 2 : At least one partition on this card is desynchronized. 3 : No contact is possible with this card. 4 : Hardware error. 5 : An error occurred during the initialization. 6 : The rebuild has failed. 7 : The rebuild of the card has to be done by the HSS supervision. 8 : Unknown software or firmware version 601 : primary external source recovery 602 : primary external source loss of signal 603 : primary external source qualification failure 604 : primary external source Alarm Indication Signal 605 : primary external source Loss Of Frame 606 : primary external source Excessive Error Indication 607 : primary external source Message failure indication 701 : secondary external source recovery 702 : secondary external source loss of signal 703 : secondary external source qualification failure 801 : primary line timing source recovery 802 : primary line timing source loss of signal 803 : primary line timing source qualification failure 901 : secondary line timing source recovery 902 : secondary line timing source loss of signal 903 : secondary line timing source qualification failure 1001 : partner BBSYN signal recovery 1002 : partner BBSYN loss of signal 1003 : partner BBSYN signal qualification failure 1101 : PDH output enable 1102 : PDH output disable 1201 : SDH output enable 1202 : SDH output disable 1301 : MSC output enable 1302 : MSC output disable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lsnHardwareProblem(1), desynchronizedPartition(2), noContact(3), hardwareError(4), initializationError(5), rebuildFailure(6), rebuildRequired(7), versionError(8), primaryExtSourceRecovery(601), primaryExtSourceLoss(602), primaryExtSourceQualifFail(603), primaryExtSourceAIS(604), primaryExtSourceLOF(605), primaryExtSourceEE(606), primaryExtSourceMSG(607), secondaryExtSourceRecovery(701), secondaryExtSourceLoss(702), secondaryExtSourceQualifFail(703), primaryLineSourceRecovery(801), primaryLineSourceLoss(802), primaryLineSourceQualifFail(803), secondaryLineSourceRecovery(901), secondaryLineSourceLoss(902), secondaryLineSourceQualifFail(903), partnerBbsynSignalRecovery(1001), partnerBbsynSignalLoss(1002), partnerBbsynSignalQualifFail(1003), pdhOutputEnable(1101), pdhOutputDisable(1102), sdhOutputEnable(1201), sdhOutputDisable(1202), mscOutputEnable(1301), mscOutputDisable(1302)  

adnBoardServiceIndicator 3.1.637.3.1.5.15.2.1.13
An indication of the services supported by this board. Boards of the same physical type may have different values for this object, depending on the services configured for the board by the NMS operator. The selection of services may also cause different software to be loaded onto the board. For the same physical board type, the software load list (SLL) may contain multiple entries, each qualified using a different value of this object as a selector. Value Meaning ------------------------------------------------------------ notSpecified(1) No specific indication is available. - This value is used for boards with - no service assignment (such as a - board in the 'spare' redundancy - role). - nodeAdmin(2) Node administration and management - services. - atmSwitching(3) ATM switching services. - frAccessAndTrunk(4) Frame relay access and trunk - services. - frxAccess(5) PSX FRX (Frame Relay eXchange) - access service. - frTrunkOverAtm(6) Frame relay trunking over ATM. - frxTrunkOverAtm(7) PSX FRX trunking over ATM. - atmAccessAndTrunk(8) ATM access and trunk services. - frAccessOverAtm(9) Frame relay access over ATM using - Frame Relay Forum (FRF) scenario 1, - scenario 2 and service interworking. - frAccessAndTrunkOverAtm(10) - Frame relay access and trunking - over ATM. The access service uses FRF - network scenario 1, scenario 2 and - service interworking. - circuitEmulation(11) Circuit emulation services. - nodeSync(12) Node-level clock synchronization - services. - ipForwarding(13) IP routing over Frame Relay or ATM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSpecified(1), nodeAdmin(2), atmSwitching(3), frAccessAndTrunk(4), frxAccess(5), frTrunkOverAtm(6), frxTrunkOverAtm(7), atmAccessAndTrunk(8), frAccessOverAtm(9), frAccessAndTrunkOverAtm(10), circuitEmulation(11), nodeSync(12), ipForwarding(13)  

adnBoardTestResult 3.1.637.3.1.5.15.2.1.14
The value of this object gives the hardware tests or rebuild result. For boards other than CU (Control Unit) boards, this object is not significant and its value is always zero. value result ----- ------------------ 0 not significant 1 other result 2 The test or rebuild has been successfuly executed and no problem has been detected 3 Internal error : HSS software error 4 Action aborted : the test or rebuilt has aborted during execution 5 Hardware tests not OK : the hardware tests have been executed but the result is hardware problem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(0), otherResult(1), resultOK(2), internalError(3), actionAborted(4), hardwareTestNOK(5)  

adnEepromTable 3.1.637.3.1.5.15.3
This table is the EEPROM table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnEepromEntry

adnEepromEntry 3.1.637.3.1.5.15.3.1
An entry in the EEPROM table. There is one entry for a given board, as there is one EEPROM on each board. The index corresponds to equipment type 'card' in the adnEquipTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnEepromEntry  

adnEepromSerialNumber 3.1.637.3.1.5.15.3.1.1
This indicates the serial number of the card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnEepromBoardName 3.1.637.3.1.5.15.3.1.2
This indicates the card type mnemonic.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnEepromPartNumberAndVariant 3.1.637.3.1.5.15.3.1.3
This indicates the Alcatel code for the card and its variant.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnEepromIcs 3.1.637.3.1.5.15.3.1.4
This indicates the Item Change Status of the card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnEepromIcsChangeDate 3.1.637.3.1.5.15.3.1.5
This indicates the date of application of a change order.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnEepromFlashIdentifier 3.1.637.3.1.5.15.3.1.6
This identifies the software loaded on flash EPROM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnEepromLastRepairDate 3.1.637.3.1.5.15.3.1.7
This indicates the date of most recent repair.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnEepromWarrantyEndDate 3.1.637.3.1.5.15.3.1.8
This indicates the date of end of warranty.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnAeiPortTable 3.1.637.3.1.5.15.4
This table is the AEI (ATM Electrical Interface) port table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAeiPortEntry

adnAeiPortEntry 3.1.637.3.1.5.15.4.1
An entry in the AEI (ATM Electrical Interface) port table. There is one entry for each port of a given ATM board, that is, two entries for HSC (High Speed Coupler) and CIG (Cell Interconnection Gateway) boards, sixteen entries for ASE (ATM Switching Element) boards. The index corresponds to equipment type 'aeiPort' in the adnEquipTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAeiPortEntry  

adnAeiPortActiveOrNot 3.1.637.3.1.5.15.4.1.1
This indicates the active/standby mode of the port; it applies to all ATM boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), standby(2)  

adnAeiPortErOrWngStatus 3.1.637.3.1.5.15.4.1.2
This variable indicates the gravity of a port failure. It is a bit map represented as a sum. Each bit position maps to the corresponding position in the nominator adnAeiPortStatus (which defines the port's failure status). The adnAeiPortErOrWngStatus bit classifies the failure as either an error (value '1') or a warning (value '0'). A bit value of '0' can also mean the failure classification does not apply to the failure status.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAeiPortStatus 3.1.637.3.1.5.15.4.1.3
This variable indicates the port status. It is a bit map represented as a sum; therefore it can represent multiple failures. For all ATM boards, except the ASE (ATM Switching Element) board, the bit positions are listed below. Errors followed by an asterisk apply to ASE boards. 1 : adnAeiPortOOS* out-of-synchronization ATM Electrical Interface 4 : adnAeiPortNFOF* network FIFO overflows 8 : adnAeiPortIEMRAMP BGIEM chip RAM parity errors 16 : adnAeiPortCECH* corrected errors in cell header 32 : adnAeiPortUCECH* uncorrected errors in cell header 64 : adnAeiPortCRCMA1 CRC errors on payload field of MA1 (Active Maintenance type 1) cells 128 : adnAeiPortCRCSIC CRC errors on payload field of SIC (Self Identified Cell) cells 256 : adnAeiPortNPE* parity errors on payload 4096 : adnAeiPortNMA1* no active maintenance cell received 16384 : adnAeiPortEMA1* error active maintenance cell received 131072 : adnAeiPortNSFOF network signalling FIFO overflow 262144 : adnAeiPortNFWF network FIFO write failure 524288 : adnAeiPortSFWF signalling FIFO write failure 1048576 : adnAeiPortNSFRF network signalling FIFO read failure 4194304 : adnAeiPortUSFRF user signalling FIFO read failure 8388608 : adnAeiPortUFWF user FIFO write failure 16777216 : adnAeiPortUSFOF user signalling FIFO overflow 33554432 : adnAeiPortNICI* cells received on non-active ICI (Internal Communication Interface) 67108864 : adnAeiPortNCRC CRC errors detected on network side 134217728 : adnAeiPortNAAL* AAL (ATM Adaptation Layer) sequence error on network side 268435456 : adnAeiPortUCRC* CRC errors detected on user side 536870912 : adnAeiPortUAAL AAL sequence error on user side For the ASE (ATM Switching Element) board, there are specific defects corresponding to the following bit positions : 2 : adnAeiPortLOS loss-of-synchronization AEI 512 : adnAeiPortRTAG error in routing tag data 1073741830: adnAeiPortURC unrouted cells N.B.: This variable is significant when the operational state of the port is disabled. When there is no port error, this variable has the value 0.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAeiPortTestResult 3.1.637.3.1.5.15.4.1.4
This is the result of the last test launched on the port. It is a bit map represented as a sum; therefore each bit corresponds to a possible cause for a failing test result ('0' if test succeeded, '1' if test failed). For HSC (High Speed Coupler) or CIG (Cell Interconnection Gateway) boards, the bit positions are: 1 : failure in the BGIEM chip RAM 2 : failure in loopback test in the BGAEI chip. For ASE (ATM Switching Element) boards, the bit position is: 2 : failure in loopback test in the BGAT1 chip. N.B.: When no test has been launched, this variable has the value zero.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAeiPortLinkId 3.1.637.3.1.5.15.4.1.5
This is the adnEquipIndex of the AEI (ATM Electrical Interface) port on the ASE (ATM Switching Element) board which is linked with this AEI port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnProcessorTable 3.1.637.3.1.5.15.6
This table is the processor table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnProcessorEntry

adnProcessorEntry 3.1.637.3.1.5.15.6.1
An entry in the processor table. There is one entry for each processor of a given board. The index corresponds to equipment type 'processor' in the adnEquipTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnProcessorEntry  

adnProcessorErOrWngStatus 3.1.637.3.1.5.15.6.1.1
This variable indicates the gravity of a processor failure. It is a bit map represented as a sum. Each bit position maps to the corresponding position in the nominator adnProcessorStatus (which defines the processor's failure status). The adnProcessorErOrWngStatus bit classifies the failure as either an error (value '1') or a warning (value '0'). A bit value of '0' can also mean the failure classification does not apply to the failure status.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnProcessorStatus 3.1.637.3.1.5.15.6.1.2
This variable indicates the processor status. It is a bit map represented as a sum; therefore it can represent multiple failures. This variable is only significant for ATM board processors. For all ATM boards except the ASE (ATM Switching Element),the bit positions are : 1 : adnProcessorUFOF user FIFO overflow 2 : adnProcessorUFRF user FIFO read failure 4 : adnProcessorNFOF network FIFO overflow 8 : adnProcessorPHTRAMP BGPHT chip RAM parity error 16 : adnProcessorNFRF network FIFO read failure 32 : adnProcessorNAVC cells received on non-active VC 64 : adnProcessorNAVP cells received on non-active VP 128 : adnProcessorRBOF reception cell buffer overflow 512 : adnProcessorPWF power failure For the ASE board, the bit positions are : 16384 : adnProcessorQRP0RAMP BGQRP-0 chip RAM parity error 32768 : adnProcessorQRP0DMA BGQRP-0 chip DMA (Direct Memory Access) error 65536 : adnProcessorQRP0FIFO BGQRP-0 chip extraction FIFO error 131072 : adnProcessorQRP1RAMP BGQRP-1 chip RAM parity error 262144 : adnProcessorQRP1DMA BGQRP-1 chip DMA error 524288 : adnProcessorQRP1FIFO BGQRP-1 chip extraction FIFO error 1048576 : adnProcessorQRP2RAMP BGQRP-2 chip RAM parity error 2097152 : adnProcessorQRP2DMA BGQRP-2 chip DMA error 4194304 : adnProcessorQRP2FIFO BGQRP-2 chip extraction FIFO error 8388608 : adnProcessorQRP3RAMP BGQRP-3 chip RAM parity error 16777216 : adnProcessorQRP3DMA BGQRP-3 chip DMA error 33554432 : adnProcessorQRP3FIFO BGQRP-3 chip extraction FIFO error 67108864 : adnProcessorHMP0LLPC BGHMP-0 chip loss of low-priority cells 134217728 : adnProcessorHMP0LHPC BGHMP-0 chip loss of high-priority cells 268435456 : adnProcessorHMP0SYNC BGHMP-0 chip synchronization fault 536870912 : adnProcessorHMP1LLPC BGHMP-1 chip loss of low-priority cells 1073741824: adnProcessorHMP1LHPC BGHMP-1 chip loss of high-priority cells 2147483648: adnProcessorHMP1SYNC BGHMP-1 chip synchronization fault N.B.: This variable is significant when the operational state of the processor is disabled. When there is no processor error, this variable has the value 0.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIfAssignmentTable 3.1.637.3.1.5.15.15
This table maps an ifIndex to its location.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIfAssignmentEntry

adnIfAssignmentEntry 3.1.637.3.1.5.15.15.1
An entry in the ifIndex assignment table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIfAssignmentEntry  

adnIfAssignmentChassis 3.1.637.3.1.5.15.15.1.1
The chassis number where the control application of the ifIndex runs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnIfAssignmentSlot 3.1.637.3.1.5.15.15.1.2
The slot number where where the control application of the ifIndex runs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnIfAssignmentLine 3.1.637.3.1.5.15.15.1.3
The line number attached to the control application of the ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIfAssignmentCtrlAppli 3.1.637.3.1.5.15.15.1.4
The control application identifier of the ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIfAssignmentLowIndex 3.1.637.3.1.5.15.15.1.5
The ifIndex of the subordinate layer of this ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnIfAssignmentTSI 3.1.637.3.1.5.15.15.1.6
This indicates whether or not the ifIndex layer is at the top of a protocol stack.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER tsifalse(0), tsitrue(1)  

adnIpAddrAssignmentTable 3.1.637.3.1.5.15.16
This table maps an ipIndex to its associate ifIndex
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIpAddrAssignmentEntry

adnIpAddrAssignmentEntry 3.1.637.3.1.5.15.16.1
An entry in the ipIndex assignment table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIpAddrAssignmentEntry  

adnIpAddress 3.1.637.3.1.5.15.16.1.1
This value is the ipIndex
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  IpAddress  

adnIpAddrAssignmentIfindex 3.1.637.3.1.5.15.16.1.2
This value is the associate ifindex to an ipIndex
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnPhysical 3.1.637.3.1.5.16
OBJECT IDENTIFIER    

adnPhyTable 3.1.637.3.1.5.16.1
A list of physical or channel-level interface entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnPhyEntry

adnPhyEntry 3.1.637.3.1.5.16.1.1
An interface entry containing objects for physical and channel-level interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnPhyEntry  

adnPhyChassis 3.1.637.3.1.5.16.1.1.1
The number of the chassis that supports this ifIndex. Common Name: Chassis
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnPhySlot 3.1.637.3.1.5.16.1.1.2
The number of the slot that supports this ifIndex. Common Name: Card
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnPhyLine 3.1.637.3.1.5.16.1.1.3
The number of the line that supports this ifIndex. Common Name: Line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnPhyChannel 3.1.637.3.1.5.16.1.1.4
The number of the channel that supports this ifIndex. Line-level interfaces have a channel value of zero. Common Name: Channel
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnPmdMIB 3.1.637.3.1.5.18
OBJECT IDENTIFIER    

adnPmdNodeTable 3.1.637.3.1.5.18.1
The objects in this table define the status of the post mortem dump (PMD) at the node level. The NMS can set or get the PMD status at the node level. The node level is the highest one in the hierarchy. If the PMD is disabled at the node level, it is also disabled at the board and processor levels. If it is enabled at the node level, it may be enabled or disabled at the lower (board and processor) levels. PMD is disable means that no PMD is generated. If the PMD filter is disabled at the node level, it is also disabled at the board and processor levels. If it is enabled at the node level, it may be enabled or disabled at the lower (board and processor) levels. PMD filter is disable means that no filter is applicated for each generated PMD. At each PMD a file is created. If the kind of PMD is 'free' at the node level, the kind of PMD generated is determined by the value at the board level. If it is not 'free', the generated PMD is the most complete kind of those indicated at the node, board and processor levels. The kind of PMD order is as follows (from least to most complete): . min -> short -> long -> full.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnPmdNodeEntry

adnPmdNodeEntry 3.1.637.3.1.5.18.1.1
An entry in the node table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnPmdNodeEntry  

adnPmdNodeEnableDisable 3.1.637.3.1.5.18.1.1.1
This variable defines whether or not the post mortem dump (PMD) is enabled at the node level. The NMS can activate or deactivate the PMD using this variable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

adnPmdNodeKindOfPmd 3.1.637.3.1.5.18.1.1.2
This defines the type of post mortem dump (PMD) to execute. This variable applies at the node level. min : post mortem dump will be minimum (only the failure ~~~ context is provided) at the board and processor . levels, unless the values of adnPmdBoardKindOfPmd . and adnPmdProcessorKindOfPmd are short, long or . full. . In this case, the more complete PMD is chosen. short : post mortem dump will be short at the board and ~~~~~ processor levels, unless the values of . adnPmdBoardKindOfPmd and adnPmdProcessorKindOfPmd . are long or full. . In this case, the more complete PMD is chosen. . Short means only the memory areas belonging to the . faulty application and explicitly declared for the . post mortem dump are extracted from the target . memory. long : post mortem dump will be long at the board and ~~~~ processor levels, unless the values of . adnPmdBoardKindOfPmd and adnPmdProcessorKindOfPmd . is full. . In this case, the full PMD is chosen. . Long means all the memory areas explicitly declared . by the applications for the post mortem dump are . extracted from the target memory. full : post mortem dump will be full (entire memory) ~~~~ at the board and processor levels, no matter what . the values are for adnPmdBoardKindOfPmd and . adnPmdProcessorKindOfPmd, no matter what the memory . areas declared by the applications are. free : the post mortem dump will be processed at the board ~~~~ and processor levels according to the values of the . adnPmdBoardKindOfPmd and adnPmdProcessorKindOfPmd . objects.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER free(1), short(2), long(3), full(4), min(5)  

adnPmdNodeSurveillance 3.1.637.3.1.5.18.1.1.3
This defines whether or not the NMS will get the post mortem dump (PMD) files from the node's to_nms transfer directory. If the node is under surveillance (enable) the NMS won't get the PMD files from the to_nms transfer directory but the PMD files continues to be created in this directory. This causes no modification of the PMD mechanism behavior.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

adnPmdNodeFilterStatus 3.1.637.3.1.5.18.1.1.4
This variable defines whether or not the post mortem dump (PMD) filter is enabled at the node level. The NMS can activate, deactivate or reset the PMD filter using this variable. After the reset action, the variable takes back its previous value at node level (either enable or disable). The node level is the highest one in the hierarchy. If the PMD filter is disabled at the node level, it is also disabled at the board and processor levels. If it is enabled at the node level, it is enabled or disabled at board level according to the status at this level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2), reset(3)  

adnPmdBoardTable 3.1.637.3.1.5.18.2
The objects in this table define the status of the post mortem dump (PMD) at the board level. The NMS can set or get the PMD status at the board level. If the PMD is disabled at the board level, it is also disabled at the processor level. If it is enabled at the board level, it may be enabled or disabled at the lower (processor) level. PMD is disable means that no PMD is generated. If the PMD filter is disabled at the board level, it is also disabled at the processor level. If it is enabled at the board level, it may be enabled or disabled at the lower (processor) level. PMD filter is disable means that no filter is applicated for each generated PMD. At each PMD a file is created. If the kind of PMD is 'free' at the board level, the kind of PMD generated is determined by the value at the processor level. If it is not 'free', the generated PMD is the most complete kind of those indicated at the board and processor levels. The kind of PMD order is as follows (from least to most complete): . min -> short -> long -> full.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnPmdBoardEntry

adnPmdBoardEntry 3.1.637.3.1.5.18.2.1
An entry in the board table. There will be one entry for each board of a given node.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnPmdBoardEntry  

adnPmdBoardEnableDisable 3.1.637.3.1.5.18.2.1.1
This variable defines whether or not the post mortem dump (PMD) is enabled at the board level. The PMD is enabled at the board level only if it is also enabled at the node level.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

adnPmdBoardKindOfPmd 3.1.637.3.1.5.18.2.1.2
This defines the type of post mortem dump (PMD) to execute. This variable applies at the board level. min : post mortem dump will be minimum (only the failure ~~~ context is provided) at the processor level, unless . the value of adnPmdProcessorKindOfPmd is short, . long or full. . In this case, the more complete PMD is chosen. short : post mortem dump will be short at the processor ~~~~~ level, unless the value of adnPmdProcessorKindOfPmd . is long or full. . In this case, the more complete PMD is chosen. . Short means only the memory areas belonging to the . faulty application and explicitly declared for the . post mortem dump are extracted from the target . memory. long : post mortem dump will be long at the processor ~~~~ level, unless the value of adnPmdProcessorKindOfPmd . is full. . In this case, the full PMD is chosen. . Long means all the memory areas explicitly declared . by the applications for the post mortem dump are . extracted from the target memory. full : post mortem dump will be full (entire memory) ~~~~ at the processor level, no matter what the value is . for adnPmdProcessorKindOfPmd, no matter what the . memory areas declared by the applications are. free : post mortem dump will be processed at the ~~~~ processor level according to the value of the . adnPmdProcessorKindOfPmd object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER free(1), short(2), long(3), full(4), min(5)  

adnPmdBoardFilterStatus 3.1.637.3.1.5.18.2.1.3
This variable defines whether or not the post mortem dump (PMD) filter is enabled at the board level. The PMD filter is enabled at the board level only if it is also enabled at the node level. The NMS can activate, deactivate or reset the PMD filter using this variable. After the reset action, the variable takes back its previous value at board level (either enable or disable).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2), reset(3)  

adnPmdProcessorTable 3.1.637.3.1.5.18.3
This object defines the status of the post mortem dump (PMD) at the processor level. The NMS can set or get the PMD status at the processor level.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnPmdProcessorEntry

adnPmdProcessorEntry 3.1.637.3.1.5.18.3.1
An entry in the processor table. There will be one entry for each processor of a given board.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnPmdProcessorEntry  

adnPmdProcessorEnableDisable 3.1.637.3.1.5.18.3.1.1
This variable defines whether or not the post mortem dump (PMD) is enabled at the processor level. The PMD is enabled at the processor level only if it is also enabled at the board and node levels.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

adnPmdProcessorKindOfPmd 3.1.637.3.1.5.18.3.1.2
This defines the type of post mortem dump (PMD) to execute. This variable applies at the processor level. min : post mortem dump will provide failure context only. ~~~ short : only the memory areas belonging to the faulty ~~~~~ application and explicitly declared for the post . mortem dump are extracted from the target memory. long : all the memory areas explicitly declared by ~~~~ the applications for the post mortem dump are . extracted from the target memory. full : post mortem dump will be full (entire memory), no ~~~~ matter what the memory areas declared by the . applications are. free : the post mortem dump mechanism will decide itself ~~~~ the kind of PMD to do.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER free(1), short(2), long(3), full(4), min(5)  

adnPmdProcessorFilterStatus 3.1.637.3.1.5.18.3.1.3
This variable defines whether or not the post mortem dump (PMD) filter is enabled at the processor level. The PMD filter is enabled at the processor level only if it is also enabled at board and node levels. The NMS can activate, deactivate or reset the PMD filter using this variable. After the reset action, the variable takes back its previous value at processor level (either enable or disable).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2), reset(3)  

adnFranpTrunkServiceMIB 3.1.637.3.1.5.4.1
OBJECT IDENTIFIER    

adnFrtChanTable 3.1.637.3.1.5.4.1.1
This table defines all the channels configured for FRANP (Frame Relay Alcatel Network Protocol). There is no existing standard MIB for Alcatel's internal network protocol. This table is owned by FRANP Signalling software module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrtChanEntry

adnFrtChanEntry 3.1.637.3.1.5.4.1.1.1
An entry in the channel table. There will be one entry for each FRANP (Frame Relay Alcatel Network Protocol) channel configured.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrtChanEntry  

adnFrtChanType 3.1.637.3.1.5.4.1.1.1.1
The value of this object identifies the type of network interface for this trunk port. Common Name: FR Trunk Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), hss(2), tpx(3), frx(4)  

adnFrtChanAddrDLCILen 3.1.637.3.1.5.4.1.1.1.2
The value of this object identifies the Q.922 address field length and DLCI (data link connection identifier) length for this trunk port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER twoOctets10Bits(1), threeOctets10Bits(2), threeOctets16Bits(3), fourOctets17Bits(4), fourOctets23Bits(5)  

adnFrtChanRNodeID 3.1.637.3.1.5.4.1.1.1.3
This is the remote routing node ID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnFrtChanRifIndex 3.1.637.3.1.5.4.1.1.1.4
This is the ifIndex of the interface on the remote node on which this VC is carried. This ifIndex has no local significance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnFrtChanBAT 3.1.637.3.1.5.4.1.1.1.5
This is the bandwidth allocation threshold for the channel. A value exceeding 80% is not recommended for sustained traffic loads. The values for adnFrtChanMaxBcsUser, adnFrtChanMaxBcsNet, and adnFrtChanMaxBe must be less than or equal to the value of adnFrtChanBAT. Common Name: BAT(%)
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnPercent  

adnFrtChanNxOverBcsUser 3.1.637.3.1.5.4.1.1.1.6
This indicates the number of times Bcs (statistically committed data rate) can be over-subscribed for user traffic on the channel. Common Name: # Times Over Subscribe Bcs-User
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanNxOverBcsNet 3.1.637.3.1.5.4.1.1.1.7
This indicates the number of times Bcs (statistically committed data rate) can be over-subscribed for net- work traffic on the channel. Common Name: # Times Over Subscribe Bcs-Network
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanNxOverBe 3.1.637.3.1.5.4.1.1.1.8
This indicates the number of times Be (excess burst data rate) can be over-subscribed for the channel. Common Name: # Times Over Subscribe Be
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanMaxBcsUser 3.1.637.3.1.5.4.1.1.1.9
This field represents the maximum percentage of the channel bandwidth allowed for Bcs (statistically committed data rate) users. It is specified as a percentage of the total bandwidth. It cannot exceed BAT (bandwidth allocation threshold). Therefore, the default value for this field should be no more than the minimum percentage specified for the BAT. Common Name: Max BW for User Bcs Traffic
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnPercent  

adnFrtChanMaxBcsNet 3.1.637.3.1.5.4.1.1.1.10
This field represents the maximum percentage of the channel bandwidth allowed for Bcs (statistically committed data rate) network traffic. It is specified as a percentage of the total bandwidth. It cannot exceed BAT (bandwidth allocation threshold). Therefore, the default value for this field should be no more than the minimum percentage specified for the BAT. Common Name: Max BW for Ntwk Bcs Traffic
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnPercent  

adnFrtChanMaxBe 3.1.637.3.1.5.4.1.1.1.11
This field represents the maximum percentage of the channel bandwidth allowed for Be(excess burst data rate). It is specified as a percentage of the total channel bandwidth. It cannot exceed BAT (bandwidth allocation threshold). Therefore, the default value for this field should be no more than the minimum percentage specified for the BAT. Common Name: Max BW for Be Traffic
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnPercent  

adnFrtChanMaxCrf 3.1.637.3.1.5.4.1.1.1.12
This is the maximum number of user calls permitted on the trunk. Common Name: Max Num User Calls
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanMinDlci 3.1.637.3.1.5.4.1.1.1.13
This is the minimum user DLCI (data link connection identifier) number permitted on the trunk. Common Name: Min DLCI Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanMaxDlci 3.1.637.3.1.5.4.1.1.1.14
This is the maximum user DLCI (data link connection identifier) number permitted on the trunk. Common Name: Max DLCI Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanTotalNumDlci 3.1.637.3.1.5.4.1.1.1.15
This is the current number of user DLCI (data link connection identifier) on the trunk. Common Name: # VC
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanUserNetFlg 3.1.637.3.1.5.4.1.1.1.16
This indicates whether the trunk follows the user or network side of the protocol recommendations. Common Name: User/Network Protocol
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER user(1), network(2)  

adnFrtChanTPXBc2HSSBcsUsr 3.1.637.3.1.5.4.1.1.1.17
This flag indicates the conversion from TPX user Bc (committed data rate) to HSS user Bcs (statistically committed data rate) if a channel is configured as a TPX Interworking Function (IWF) channel. An IWF is a trunk line connecting a TPX to an HSS. Common Name: Convert TPX Bc to HSS User Bcs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(1), true(2)  

adnFrtChanTPXBc2HSSBcsNet 3.1.637.3.1.5.4.1.1.1.18
This flag indicates the conversion from TPX network Bc (committed data rate) to HSS user Bcs (statistically committed data rate) if a channel is configured as a TPX Interworking Function (IWF) channel. An IWF is a trunk line connecting a TPX to an HSS. Common Name: Convert TPX Bc to HSS Ntwk Bcs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(1), true(2)  

adnFrtChanStatistics 3.1.637.3.1.5.4.1.1.1.19
This indicates if statistics are enabled on this channel. Common Name: Statistics
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFrtChanT303 3.1.637.3.1.5.4.1.1.1.20
This timer specifies the amount of time to wait for a setup response. If the timer expires, then the setup message is retransmitted. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanT305 3.1.637.3.1.5.4.1.1.1.21
This timer specifies the amount of time to wait for a disconnect response. If the timer expires, then the release message is transmitted. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanT308 3.1.637.3.1.5.4.1.1.1.22
This timer specifies the amount of time to wait for a release response. If the timer expires the first time, then the release message is retransmitted. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanT309 3.1.637.3.1.5.4.1.1.1.23
This data link timer specifies the amount of time to wait for re-establishment of the LAPD (link access procedure on the D-channel) message. If the timer expires, all calls will be cleared. Otherwise, calls in stable states are not lost. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanT310 3.1.637.3.1.5.4.1.1.1.24
This timer specifies the amount of time to wait for a Call Proceeding response. If the timer expires, then the call is cleared by transmitting a disconnect message. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanT313 3.1.637.3.1.5.4.1.1.1.25
This timer specifies the amount of time to wait for a connect response. If the timer expires, then the call is cleared by transmitting a disconnect message. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanT315 3.1.637.3.1.5.4.1.1.1.26
This timer specifies the amount of time to wait for a status inquiry response. If the timer expires, then the call is cleared by transmitting a disconnect message. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanT316 3.1.637.3.1.5.4.1.1.1.27
This timer specifies the amount of time to wait for a restart response. If the timer expires, then the restart message is re-transmitted. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanT317 3.1.637.3.1.5.4.1.1.1.28
Not used for Release 2.0. Reserved for future use. This restart confirm timer specifies the amount of time to wait for clearing all the calls. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanT320 3.1.637.3.1.5.4.1.1.1.29
Not used for Release 2.0. Reserved for future use. This inactivity timer specifies the amount of time to wait for a response to a call. The timer value is expressed in seconds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanNxOverBeControl 3.1.637.3.1.5.4.1.1.1.30
This indicates whether the oversubscription factor for Be is enabled or disabled. When disabled, the value for Be is not taken into account when allocating bandwidth for a call. Common Name: Be oversubscription factor control
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFrtChanMonetaryCost 3.1.637.3.1.5.4.1.1.1.31
adnFrtChanMonetaryCost identifies the monetary cost of this channel. This is an arbitrary value and is significant only in relation to the monetary cost of other links. The cost is used for route selection. A value of 0 means that this cost is not taken into account for route selection Common name: Monetary Cost
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanDelayMeasured 3.1.637.3.1.5.4.1.1.1.32
The sum of the transmission and queueing delays (in milliseconds) measured on this channel. Common Name: Measured Delay Cost
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanDelayInUse 3.1.637.3.1.5.4.1.1.1.33
The sum of the transmission and queueing delays (in milliseconds) currently used as delay cost for this channel. Common Name: Delay Cost In Use
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanDelayReMeasReq 3.1.637.3.1.5.4.1.1.1.34
Request for a new delay measurement. When set to inProgress a new delay measurement is initiated and the result is stored in the object adnFrtChanDelayMeasured.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notInProgress(1), inProgress(2)  

adnFrtChanDefaultCos 3.1.637.3.1.5.4.1.1.1.35
The Class of Service that is applied to call with no Class of Service specified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnFrCos  

adnFrtChanPerDlyIntrv 3.1.637.3.1.5.4.1.1.1.36
This field defines the periodic delay sampling interval in seconds. When this interval expires, the line delay will automatically be measured. A zero value will disable periodic delay measurments.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnFrtChanTotalUsrPVCsUp 3.1.637.3.1.5.4.1.1.1.37
This is the current number of user PVCs for which the value of adnFrtVCOperState is up. Common Name: # PVC
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanTotalUsrSVCsUp 3.1.637.3.1.5.4.1.1.1.38
This is the current number of user SVCs for which the value of adnFrtVCOperState is up. Common Name: # SVC
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtCosTable 3.1.637.3.1.5.4.1.5
This is the Class of Service table for FRANP trunk protocol.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrtCosEntry

adnFrtCosEntry 3.1.637.3.1.5.4.1.5.1
Class of Service table entry for FRANP trunk protocol.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrtCosEntry  

adnFrtCosIndex 3.1.637.3.1.5.4.1.5.1.1
The Cos (Class Of Service) index for a specific class of service managed by this frame relay interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnFrCos  

adnFrtCosAdminStatus 3.1.637.3.1.5.4.1.5.1.2
This object provides a mechanism for controlling the status of this Class of Service. Set to locked(2) it will cause any new calls to this Class of Service be rejected. Set to unlocked(1) it will cause resumption of the normal operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnFrCosAdminStatus  

adnFrtCosOperStatus 3.1.637.3.1.5.4.1.5.1.3
This object indicates the operational status of this Class of Service. A value of locked(2) indicates that any new calls will be rejected for this Class of Service. A value of unlocked(1) indicates normal operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnFrCosOperStatus  

adnFrtChanStatsTable 3.1.637.3.1.5.4.1.2
This table defines all the channel level statistics for FRANP_SW subsystem.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrtChanStatsEntry

adnFrtChanStatsEntry 3.1.637.3.1.5.4.1.2.1
An entry in the channel level statistics table. There wll be one entry for each FRANP (Frame Relay Alcatel Network Protocol) channel configured.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrtChanStatsEntry  

adnFrtChanStatsCommitEgress 3.1.637.3.1.5.4.1.2.1.2
This is the sum of committed egress bandwidth. Common Name: Commit Egress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanStatsCommitIngress 3.1.637.3.1.5.4.1.2.1.3
This is the sum of committed ingress bandwidth. Common Name: Commit Ingress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanStatsOverEgress 3.1.637.3.1.5.4.1.2.1.4
This is the sum of overcommitted egress bandwidth. Common Name: Over Egress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanStatsOverIngress 3.1.637.3.1.5.4.1.2.1.5
This is the sum of overcommitted ingress bandwidth. Common Name: Over Ingress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanStatsBcInDiscards 3.1.637.3.1.5.4.1.2.1.6
This is the sum of all of Bc (committed data rate) sub-frames that were discarded for ingress TPX IWF (Interworking Function) traffic due to calendar queue congestion. Calendar queue is a mechanism to manage submission of data into the network based on the SIR (submission of information rate). Common Name: Bc Discards In
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtChanStatsBcsInDiscards 3.1.637.3.1.5.4.1.2.1.7
This is the sum of all Bcs (statistically committed data rate) sub-frames that were discarded for ingress TPX IWF (Interworking Function) traffic due to calendar queue congestion. Calendar queue is a mechanism to manage submission of data into the network based on the SIR (submission of information rate). Common Name: Bcs Discards In
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtChanStatsBeInDiscards 3.1.637.3.1.5.4.1.2.1.8
This is the sum of all Be (excess burst data rate) sub-frames that were discarded for ingress TPX IWF (Interworking Function) traffic due to calendar queue congestion. Calendar queue is a mechanism to manage submission of data into the network based on the SIR (submission of information rate). Common Name: Be Discards In
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtChanStatsBcOutDiscards 3.1.637.3.1.5.4.1.2.1.9
This indicates the sum of Bc (committed data rate) sub-frames that were discarded for egress traffic (i.e., TPX Interworking Function, frame relay subsystem, or frame relay switching interface) due to line driver transmit queue congestion. Common Name: Bc Discards Out
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtChanStatsBcsOutDiscards 3.1.637.3.1.5.4.1.2.1.10
This indicates the sum of Bcs (statistically committed data rate) sub-frames that were discarded for egress traffic (i.e., TPX Interworking Function, frame relay subsystem, or frame relay switching interface) due to line driver transmit queue congestion. Common Name: Bcs Discards Out
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtChanStatsBeOutDiscards 3.1.637.3.1.5.4.1.2.1.11
This indicates the sum of Be (excess burst data rate) sub-frames that were discarded for egress traffic (i.e., TPX Interworking Function, frame relay subsystem, or frame relay switching interface) due to line driver transmit queue congestion. Common Name: Be Discards Out
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtChanStatsCongsState 3.1.637.3.1.5.4.1.2.1.12
This indicates the congestion level of this channel in the transmit direction. It monitors the line driver transmit queue depth.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnCongestLevels  

adnFrtChanStatsCosRtBcEgress 3.1.637.3.1.5.4.1.2.1.13
This is the sum of committed egress bandwidth for Class of Service RT. Common Name: Real Time Data Bc Commit Egress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanStatsCosRtBcIngress 3.1.637.3.1.5.4.1.2.1.14
This is the sum of committed ingress bandwidth for Class of Service RT. Common Name: Real Time Data Bc Commit Ingress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanStatsCosNrtBcEgress 3.1.637.3.1.5.4.1.2.1.15
This is the sum of committed egress bandwidth for Class of Service NRT. Common Name: Non-Real Time Data Bc Commit Egress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtChanStatsCosNrtBcIngress 3.1.637.3.1.5.4.1.2.1.16
This is the sum of committed ingress bandwidth for Class of Service NRT. Common Name: Non-Real Time Data Bc Commit Ingress
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCTable 3.1.637.3.1.5.4.1.3
This is the VC table for FRANP (Frame Relay Alcatel Network Protocol) trunk protocol. This table is owned by FRANP Signalling software module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrtVCEntry

adnFrtVCEntry 3.1.637.3.1.5.4.1.3.1
VC table entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrtVCEntry  

adnFrtVCDLCIIndex 3.1.637.3.1.5.4.1.3.1.1
The value of this object is equal to the DLCI (data link connection identifier) value for the frame relay trunk. Common Name: Local DLCI
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCSetupDir 3.1.637.3.1.5.4.1.3.1.2
The direction of the setup message. It can be either entering the node (ingress) or exiting the node (egress).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ingress(1), egress(2)  

adnFrtVCAdminState 3.1.637.3.1.5.4.1.3.1.3
The desired state of the call. Common Names: Administrative, Status Administrative
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnFrtVCOperState 3.1.637.3.1.5.4.1.3.1.4
The current state of the call. Common Names: Operational, Status Operational
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

adnFrtVCForcedPath 3.1.637.3.1.5.4.1.3.1.5
This specifies that this VC must take a forced path through the network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnFrtVCTrafficType 3.1.637.3.1.5.4.1.3.1.6
This indicates if this is a user or network call. The priority given to each type of call's data in the network differs: user call priority = customer traffic; network call priority = network traffic such as alarms, accounting, and statistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER usercall(1), networkcall(2)  

adnFrtVCState 3.1.637.3.1.5.4.1.3.1.7
This defines the states that are implemented and supported for the Frame Relay Alcatel Network Protocol signalling interface on the trunk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnFrtVCStates  

adnFrtVCRemoteDlci 3.1.637.3.1.5.4.1.3.1.8
This is the ingress DLCI (data link connection identifier) associated with the VC. Common Name: Remote DLCI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCRemoteDlciLen 3.1.637.3.1.5.4.1.3.1.9
This is the length of the ingress VC's DLCI (data link connection identifier).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER twoOctets10Bits(1), threeOctets10Bits(2), threeOctets16Bits(3), fourOctets17Bits(4), fourOctets23Bits(5)  

adnFrtVCRemoteifIndex 3.1.637.3.1.5.4.1.3.1.10
This is the ifIndex of the interface on the remote node on which this VC is carried. This ifIndex has no local significance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnFrtVCAdjacentNodeID 3.1.637.3.1.5.4.1.3.1.11
This is the routing node ID of the adjacent node to which the channel carrying this VC is connected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnFrtVCAdjacentifIndex 3.1.637.3.1.5.4.1.3.1.12
This is the ifIndex of the interface on the adjacent node on which this VC is carried. This ifIndex has no local significance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnFrtVCBcForward 3.1.637.3.1.5.4.1.3.1.13
This specifies the committed data rate, in bits per second, in the forward direction. Note that forward data may be ingress or egress depending on the setting of adnFrtVCSetupDir.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCBcBackward 3.1.637.3.1.5.4.1.3.1.14
This specifies the committed data rate, in bits per second, in the backward direction. Note that backward data may be ingress or egress depending on the setting of adnFrtVCSetupDir.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCBeForward 3.1.637.3.1.5.4.1.3.1.15
This specifies the excessive burst data rate, in bits per second, in the forward direction. Note that forward data may be ingress or egress depending on the setting of adnFrtVCSetupDir.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCBeBackward 3.1.637.3.1.5.4.1.3.1.16
This specifies the excessive burst data rate, in bits per second, in the backward direction. Note that backward data may be ingress or egress depending on the setting of adnFrtVCSetupDir.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCBcsForward 3.1.637.3.1.5.4.1.3.1.17
This specifies the statistically committed data rate, in bits per second, in the forward direction. Note that forward data may be ingress or egress depending on the setting of adnFrtVCSetupDir.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCBcsBackward 3.1.637.3.1.5.4.1.3.1.18
This specifies the statistically committed data rate, in bits per second, in the backward direction. Note that backward data may be ingress or egress depending on the setting of adnFrtVCSetupDir.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCCirForward 3.1.637.3.1.5.4.1.3.1.19
This specifies the committed information rate, in bits per second, in the forward direction. Note that forward data may be ingress or egress depending on the setting of adnFrtVCSetupDir.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCCirBackward 3.1.637.3.1.5.4.1.3.1.20
This specifies the committed information rate, in bits per second, in the backward direction. Note that backward data may be ingress or egress depending on the setting of adnFrtVCSetupDir.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCDelayCostRem 3.1.637.3.1.5.4.1.3.1.21
The delay cost (in milliseconds) allowed between this node and the destination node for setting up this PVC. Common Name: Remaining Delay Cost
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCMonetaryCostRem 3.1.637.3.1.5.4.1.3.1.22
The monetary cost allowed between this node and the destination node for setting up this VC. Common Name: Remaining Monetary Cost
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCHopCostRem 3.1.637.3.1.5.4.1.3.1.23
The number of hops allowed between this node and the destination node for setting up this VC. Common Name: Remaining Hop Cost
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnFrtVCRoutingMode 3.1.637.3.1.5.4.1.3.1.24
The routing mode used for routing this VC. When best effort is used, routing is done without regards to the cost requirement. When best effort is not used, routing must take into account the cost requirement. Common Name: Routing Mode
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bestEffort(1), considerCost(2)  

adnFrtVCPathSelectMode 3.1.637.3.1.5.4.1.3.1.25
The mode the path selection function must use to select a path for this VC. Best available service uses the lowest cost path(s) which meet the cost requirement as the primary path. With this approach, the first calls set up in the network potentially receive a higher quality service than calls which happen to arrive later. Best fit service uses the highest cost path(s) which meet the cost requirement as the primary path(s). This approach uses the least required resources to satisfy the cost function and conserves the higher quality of service for those calls which may require them. Common Name: Path Selection Mode
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bestFit(1), bestAvailable(2)  

adnFrtVCRtsCritID 3.1.637.3.1.5.4.1.3.1.26
The index into adnRtsCritSmryTable of the routing criteria applied for this VC. Common Name: Routing Criteria ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFrtVCType 3.1.637.3.1.5.4.1.3.1.27
This indicates the type of VC for the call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pvc(1), svc(2)  

adnFrtVCCos 3.1.637.3.1.5.4.1.3.1.28
This indicates the Class of Service for the call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnFrCos  

adnFrtVCStatsTable 3.1.637.3.1.5.4.1.4
This is the VC table for the FRANP (Frame Relay Alcatel Network Protocol) trunk protocol. This table is owned by FRANP Switching software module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrtVCStatsEntry

adnFrtVCStatsEntry 3.1.637.3.1.5.4.1.4.1
An entry in the VC statistics table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrtVCStatsEntry  

adnFrtVCStatsTime 3.1.637.3.1.5.4.1.4.1.1
The time the VC was initialized.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnNodeTimeStamp  

adnFrtVCStatsSubFrameIN 3.1.637.3.1.5.4.1.4.1.2
The number of ingress sub-frames for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsSubFrameOUT 3.1.637.3.1.5.4.1.4.1.3
The number of egress sub-frames for this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsBcOutDiscards 3.1.637.3.1.5.4.1.4.1.4
This indicates the number of Bc (committed data rate) sub-frames that were discarded for egress traffic (ie., TPX Interworking Function, frame relay subsystem, or frame relay switching interface) due to line driver transmit queue congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsBcsOutDiscards 3.1.637.3.1.5.4.1.4.1.5
This indicates the number of Bcs (statistically committed data rate) sub-frames that were discarded for egress traffic (ie., TPX Interworking Function, frame relay subsystem, or frame relay switching interface) due to line driver transmit queue congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsBeOutDiscards 3.1.637.3.1.5.4.1.4.1.6
This indicates the number of Be (excess burst data rate) sub-frames that were discarded for egress traffic (i.e., TPX Interworking Function, frame relay subsystem, or frame relay switching interface) due to line driver transmit queue congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsIWFBcInDiscards 3.1.637.3.1.5.4.1.4.1.7
This indicates the number of Bc (committed data rate) sub-frames that were discarded for ingress TPX/IWF (Interworking Function) traffic due to calendar queue congestion. Calendar queue is a mechanism to manage submission of data into the network based on the SIR (submission of information rate).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsIWFBcsInDiscards 3.1.637.3.1.5.4.1.4.1.8
This indicates the number of Bcs (statistically committed data rate) sub-frames that were discarded for ingress TPX /IWF (Interworking Function) traffic due to calendar queue congestion. Calendar queue is a mechanism to manage submission of data into the network based on the SIR (submission of information rate).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsIWFBeInDiscards 3.1.637.3.1.5.4.1.4.1.9
This indicates the number of Be (excess burst data rate) sub-frames that were discarded for ingress TPX/IWF (Interworking Function) traffic due to calendar queue congestion. Calendar queue is a mechanism to manage submission of data into the network based on the SIR (submission of information rate).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsIWFBcOutDiscards 3.1.637.3.1.5.4.1.4.1.10
This indicates the number of Bc (committed data rate) sub-frames that were discarded for egress TPX/IWF (Interworking Function) traffic due to XON/XOFF (flow control on and flow control off) queue congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsIWFBcsOutDiscards 3.1.637.3.1.5.4.1.4.1.11
This indicates the number of Bcs (statistically committed data rate) sub-frames that were discarded for egress TPX /IWF (Interworking Function) traffic due to XON/XOFF (flow control on and flow control off) queue congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsIWFBeOutDiscards 3.1.637.3.1.5.4.1.4.1.12
This indicates the number of Be (excess burst data rate) sub-frames that were discarded for egress TPX/IWF (Interworking Function) traffic due to XON/XOFF (flow control on and flow control off) queue congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrtVCStatsInCongsState 3.1.637.3.1.5.4.1.4.1.13
This indicates the congestion level of this VC in the ingress direction. This state is based on the amount of data in the calendar queue, which is a mechanism to manage submission of data into the network based on the SIR (submission of information rate). Common Name: Congestion Level
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnCongestLevels  

adnLapMIB 3.1.637.3.1.5.4.2
OBJECT IDENTIFIER    

adnLapParamTable 3.1.637.3.1.5.4.2.1
This table contains configurable LAP (link access procedure) parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnLapParamEntry

adnLapParamEntry 3.1.637.3.1.5.4.2.1.1
Configured parameter values for a specific LAP (link access procedure).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnLapParamEntry  

adnLapDLCIIndex 3.1.637.3.1.5.4.2.1.1.1
DLCI (data link connection identifier) index.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnLapParamStationType 3.1.637.3.1.5.4.2.1.1.2
Identifies the desired station type of this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), network(2), user(3), layer-3-selects(4)  

adnLapParamN201FrameSize 3.1.637.3.1.5.4.2.1.1.3
The default maximum N201 information field size (in number of bits) for a frame the DCE/remote DTE exchanges with this DTE. This excludes flags and 0 bits inserted for transparency.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnLapParamKWindowSize 3.1.637.3.1.5.4.2.1.1.4
The default window size for this interface. This is the maximum number of unacknowledged sequenced PDUs (protocol data units) that may be outstanding from this DTE at any one time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnLapParamN200RxmitCount 3.1.637.3.1.5.4.2.1.1.5
The default N200 retry counter for this interface. This specifies the number of times a PDU (protocol data unit) will be resent after timer T200 expires without acknowledging the PDU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnLapParamT200AckTimer 3.1.637.3.1.5.4.2.1.1.6
The default T200 timer for this interface. This specifies the maximum time (in milliseconds) to wait for acknowledgment of a PDU (protocol data unit).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnLapParamT203IdleTimer 3.1.637.3.1.5.4.2.1.1.7
The T203 timer for this interface. This specifies the maximum time (in milliseconds) to allow without frames being exchanged on the data link. A value of '2147483647' indicates that no idle timer is being kept.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnLapParamProtocolID 3.1.637.3.1.5.4.2.1.1.8
This identifies the protocol to be used on this interface. Common name: Protocol
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), lapdQ921(2), lapfQ922(3), layer-3-selects(4)  

adnLapParamAlarmsEnable 3.1.637.3.1.5.4.2.1.1.9
Indicates whether or not alarm generation is enabled for this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

adnLapParamPerfEnable 3.1.637.3.1.5.4.2.1.1.10
Indicates whether or not statistics generation is enabled for this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

adnLapFlowTable 3.1.637.3.1.5.4.2.3
This table defines the objects recorded by LAP (link access procedure) to provide information about the traffic flow through the interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnLapFlowEntry

adnLapFlowEntry 3.1.637.3.1.5.4.2.3.1
This contains information regarding the effects of flow controls in LAP (link access procedure).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnLapFlowEntry  

adnLapFlowStateChanges 3.1.637.3.1.5.4.2.3.1.2
The number of LAP (link access procedure) state changes, including resets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLapFlowChangeReason 3.1.637.3.1.5.4.2.3.1.3
The reason for the most recent incrementing of adnlapFlowStateChanges.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notStarted(1), abmeEntered(2), abmeReset(3), dmReceived(4), dmSent(5), discReceived(6), frmrReceived(8), frmrSent(9), n200Timeout(10), other(11)  

adnLapFlowCurrentMode 3.1.637.3.1.5.4.2.3.1.4
The current condition of the session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), disconnected(2), linkSetup(3), frameReject(4), informationTransfer(6), rejFrameSent(7), waitingAcknowledgement(8), stationBusy(9), remoteStationBusy(10), bothStationsBusy(11), waitingAckStationBusy(12), waitingAckRemoteBusy(13), waitingAckBothBusy(14), rejFrameSentRemoteBusy(15), xidFrameSent(16), error(17)  

adnLapFlowBusyDefers 3.1.637.3.1.5.4.2.3.1.5
The number of times this device was unable to transmit a frame due to a perceived remote busy condition. Busy conditions can result from the receipt of an RNR (receive not ready) from the remote device, the lack of valid sequence number space (window saturation), or other conditions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLapFlowRejOutPkts 3.1.637.3.1.5.4.2.3.1.6
The number of REJ (reject) frames sent by this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLapFlowRejInPkts 3.1.637.3.1.5.4.2.3.1.7
The number of REJ (reject) frames received by this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLapFlowT200Timeouts 3.1.637.3.1.5.4.2.3.1.8
The number of times a transmission was resent because the T200 timer expired.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLapFlowT203Timeouts 3.1.637.3.1.5.4.2.3.1.9
The number of times a transmission was resent because the T203 timer expired.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLapFlowLinkResets 3.1.637.3.1.5.4.2.3.1.10
The number of times a SABME (set asynchronous balanced mode extended) was received while this interface was in data transfer state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLapFlowNsErrorsIns 3.1.637.3.1.5.4.2.3.1.11
The number of Ns (send sequence number) errors that were detected on this interface while in data transfer state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLapFlowNrErrorsIns 3.1.637.3.1.5.4.2.3.1.12
The number of Nr (receive sequence number) errors that were detected on this interface while in data transfer state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnLapFlowFrmrSent 3.1.637.3.1.5.4.2.3.1.13
The information field of the FRMR (frame reject) most recently sent. If no FRMR has been sent (the normal case) or the information is not available, this will be an OCTET STRING of zero length.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnLapFlowFrmrReceived 3.1.637.3.1.5.4.2.3.1.14
The information field of the FRMR (frame reject) most recently received. If no FRMR has been received (the normal case) or the information is not available, this will be an OCTET STRING of zero length.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnDs1 3.1.637.3.1.4.10.18
OBJECT IDENTIFIER    

adnDsx1ConfigTable 3.1.637.3.1.4.10.18.1
This table is the extension of the dsx1ConfigTable described in the DS1/E1 standard MIB.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1ConfigEntry

adnDsx1ConfigEntry 3.1.637.3.1.4.10.18.1.1
An entry in the DS1 Configuration table extension.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1ConfigEntry  

adnDsx1LineType 3.1.637.3.1.4.10.18.1.1.1
The field is used to qualify the dsx1LineType. noQual - No qualification. e1Unframed - E1 with no framing
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noQual(1), dsx1E1Unframed(2)  

adnDsx1LineLength 3.1.637.3.1.4.10.18.1.1.2
The length of the DS1 line in meters. This object provides information for line build out circuitry if it exists and can profitably use the information. Accuracy should be within 30 meters. For many short lines and for lines that cannot use this information, the value zero is appropriate. Line build out circuitry sets electrical power levels in the transmitter, and sensitivity in the receiver. The line length means the distance to the nearest electrical regeneration point (which could be a simple repeater, or a CSU or DACS/multiplexer, or even a direct connection to another switch, etc. There is a possibility of increased noise (or even total signal loss) if the length is not set properly.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnDsx1LineStatus 3.1.637.3.1.4.10.18.1.1.3
This variable indicates the status of the line interface. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnDsx1NoAlarm bit should be set only if no other bit is set. The bit positions and their corresponding ATM core counter numbers # are: # Bit Value ------------------------------------------------------ . 1 noAlarm . No alarm present 21 2 HBERError . High bit error rate (HBER) 23 4 RLBError . Loopback requested by the remote equipment 30 8 LCMAError . Loss of CRC multiframe alignment Common Name: Line Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnDsx1MsAisTest 3.1.637.3.1.4.10.18.1.1.4
This variable is used to send a constant alarm indication signal (AIS) to the remote equipment. This object is used only for testing and debugging. This object is available for ATM T1/E1 only. Common Name: Forcing a Line Alarm Indication Signal
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

adnDsx1MsFerfTest 3.1.637.3.1.4.10.18.1.1.5
This variable is used to send a constant yellow alarm signal at the frame level to the remote equipment. This object is used only for testing and debugging. This object is available for ATM T1/E1 only. Common Name: Forcing a Line FERF Signal
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

adnDsx1RemLoopbackTest 3.1.637.3.1.4.10.18.1.1.6
This variable is used to force a loopback of the line of the remote equipment
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER lineNoLoop(1), lineLoop(3)  

adnDsx1LineHWStatus 3.1.637.3.1.4.10.18.1.1.7
This variable indicates the hardware status of a line. The given status value corresponds to the last test initiated by setting the nominator ifTestType with adnIfTest- TypeLineHW test identifier. If the result of the test, given by the nominator ifTestResult, is different than 'success' or 'failed', the given status value is not significant. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnDsx1LineHWNoDefect bit should be set only if no other bit is set. If the status is not significant, all the bits are reset. The bit positions are: 1 lineHWNoDefect 2 BGPHT chip failure 4 not used 8 CBD chip failure on line side 8 framer chip failure on the input side 16 framer chip failure on line side
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnDsx1StatType 3.1.637.3.1.4.10.18.1.1.8
The field displays the standard used for computing the statistics counters. noStatistics : no statistics are available on the ds1/E1 interface ansi : ANSI T1.231 statistics are activated itu : ITU G.826 statistics are activated
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noStatistics(1), ansi(2), itu(3)  

adnDsx1LinePerfStatus 3.1.637.3.1.4.10.18.1.1.9
This variable indicates the performance status of the interface. It is a bit map represented as a sum; therefore, it can represent multiple status simultaneously. - The NoDefect bit should be set only if no other bit is set. - The UnavailablePeriod indicates that the interface has entered an unavailable period. - The CurrentCrossingThreshold bit indicates that one of the current statistics counter has reached its threshold. - The DayIntervalCrossingThreshold bit indicates that one of the Day Interval statistics counter has reached its threshold. The bit positions are: 1 noDefect 2 unavailablePeriod 4 currentCrossingThreshold 8 dayIntervalCrossingThreshold
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnDsx1CounterTable 3.1.637.3.1.4.10.18.2
The DS1/E1 ADN Counter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1CounterEntry

adnDsx1CounterEntry 3.1.637.3.1.4.10.18.2.1
An entry in the DS1/E1 ADN Counter table .
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1CounterEntry  

adnDsx1LosCounter 3.1.637.3.1.4.10.18.2.1.1
Duration of loss-of-signal (LOS). Counter #0 of the ATM core, only available on ATM-T1, ATM-E1, CES-T1 and CES-E1 interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1AisCounter 3.1.637.3.1.4.10.18.2.1.2
Duration of alarm indication signal (AIS). Counter #2 of the ATM core, only available on ATM-T1, ATM-E1, CES-T1 and CES-E1 interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1FerfCounter 3.1.637.3.1.4.10.18.2.1.3
Duration of far end received failure (FERF) received from the remote equipment. FERF is also called remote alarm indication (RAI) or received yellow alarm. Counter #3 of the ATM core, only available on ATM-T1, ATM-E1, CES-T1 and CES-E1-Framed interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1FeCounter 3.1.637.3.1.4.10.18.2.1.4
Number of frame bit errors (FE). Counter #5 of the ATM core, only available on ATM-E1, CES-T1 and CES-E1-Framed interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1LofCounter 3.1.637.3.1.4.10.18.2.1.5
Duration of loss-of-frame (LOF). Counter #7 of the ATM core, only available on ATM-T1, ATM-E1, CES-T1 and CES-E1-Framed interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1FebeCounter 3.1.637.3.1.4.10.18.2.1.6
Number of far end block errors (FEBE). Counter #9 of the ATM core, only available on ATM-E1 and CES-E1-CRC interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1PcvCounter 3.1.637.3.1.4.10.18.2.1.7
Path Coding Violation (PCV) Error Event. A Path Coding Violation error event is : - a frame synchronization bit error in the T1-SF and E1 no CRC formats, - a CRC-6 error in the T1-ESF format, - a CRC-4 error in the E1 CRC formats. Counter #11 of the ATM core, only available on ATM-T1, ATM-E1, CES-T1 and CES-E1-CRC interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1Ts16AisCounter 3.1.637.3.1.4.10.18.2.1.8
Duration of Alarm Indication Signal in time slot 16 signalling channel (TS16AIS). Counter #17 of the ATM core, only available on CES-E1-Multiframed interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1RsaCounter 3.1.637.3.1.4.10.18.2.1.9
Duration of Remote Signalling Multiframe Alarm (RSA). Counter #18 of the ATM core, only available on CES-E1-Multiframed interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1LsmaCounter 3.1.637.3.1.4.10.18.2.1.10
Duration of Loss of Signalling Multiframe Alignment (LSMA). Counter #19 of the ATM core, only available on CES-E1-Multiframed interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1LcvCounter 3.1.637.3.1.4.10.18.2.1.11
Number of Line Code Violations (LCV). Counter #21 of the ATM core, only available on ATM-T1, ATM-E1, CES-T1 and CES-E1 interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1LcmaCounter 3.1.637.3.1.4.10.18.2.1.12
Duration of Loss of CRC Multiframe Alignment (LCMA). Counter #30 of the ATM core, only available on CES-E1-CRC interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1SefCounter 3.1.637.3.1.4.10.18.2.1.13
Number of Severely Errored Frames (SEF). Counter #30 of the ATM core, only available on CES-T1 interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1ExzCounter 3.1.637.3.1.4.10.18.2.1.14
Number of excessive zeros (EXZ). Counter #31 of the ATM core, only available on ATM-T1 and CES-T1 interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnDsx1CurrentTable 3.1.637.3.1.4.10.18.3
The ADN DS1/E1 Current table. This table is supported by CES-T1 interfaces. This table refers to ANSI T1.231.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1CurrentEntry

adnDsx1CurrentEntry 3.1.637.3.1.4.10.18.3.1
An entry in the ADN DS1/E1 Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1CurrentEntry  

adnDsx1CurrentLSESs 3.1.637.3.1.4.10.18.3.1.1
Number of Severely errored seconds (SES-L) at line level encountered during the current 15-minute interval. Common Name: Severely Errored Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1CurrentLLOSSs 3.1.637.3.1.4.10.18.3.1.2
Number of seconds containing one or more LOS defects (LOSS-L) encountered during the current 15-minute interval. Common Name: LOS Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1CurrentAESs 3.1.637.3.1.4.10.18.3.1.3
Number of errored seconds of type A at path level (ESA-P) encountered during the current 15-minute interval. Common Name: Errored Seconds of type A
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1CurrentAISSs 3.1.637.3.1.4.10.18.3.1.4
Number of seconds containing one or more AIS defects at path level (AISS-P) encountered during the current 15-minute interval. Common Name: AIS Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1IntervalTable 3.1.637.3.1.4.10.18.4
The ADN DS1/E1 Interval table. This table is supported by CES-T1 interfaces. This table refers to ANSI T1.231.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1IntervalEntry

adnDsx1IntervalEntry 3.1.637.3.1.4.10.18.4.1
An entry in the ADN DS1/E1 Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1IntervalEntry  

adnDsx1IntervalNumber 3.1.637.3.1.4.10.18.4.1.1
A number which identifies the interval for which the set of statistics is available. The previous 24-hour period is divided into 96 15-minute intervals. The interval identified by 1 is the most recently completed 15-minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnDsx1IntervalLSESs 3.1.637.3.1.4.10.18.4.1.2
Number of Severely errored seconds (SES-L) at line level encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1IntervalLLOSSs 3.1.637.3.1.4.10.18.4.1.3
Number of seconds containing one or more LOS defects (LOSS-L) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1IntervalAESs 3.1.637.3.1.4.10.18.4.1.4
Number of errored seconds of type A at path level (ESA-P) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1IntervalAISSs 3.1.637.3.1.4.10.18.4.1.5
Number of seconds containing one or more AIS defects at path level (AISS-P) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalTable 3.1.637.3.1.4.10.18.5
The ADN DS1/E1 Day Interval table. This table is supported by CES-T1 interfaces. This table refers to ANSI T1.231.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1DayIntervalEntry

adnDsx1DayIntervalEntry 3.1.637.3.1.4.10.18.5.1
An entry in the ADN DS1/E1 Day Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1DayIntervalEntry  

adnDsx1DayIntervalESs 3.1.637.3.1.4.10.18.5.1.1
The number of Errored Seconds (ES) encountered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalSESs 3.1.637.3.1.4.10.18.5.1.2
The number of Severely Errored Seconds (SES) encoun- tered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalSEFSs 3.1.637.3.1.4.10.18.5.1.3
The number of Severely Errored Framing Seconds (SEFS) encountered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalUASs 3.1.637.3.1.4.10.18.5.1.4
The number of Unavailable Seconds (UAS) encountered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalCSSs 3.1.637.3.1.4.10.18.5.1.5
The number of Controlled Slip Seconds (CSS) encoun- tered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalPCVs 3.1.637.3.1.4.10.18.5.1.6
The number of Path Coding Violations (PCV) encoun- tered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalLESs 3.1.637.3.1.4.10.18.5.1.7
The number of Line Errored Seconds (LES) encountered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalBESs 3.1.637.3.1.4.10.18.5.1.8
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalLCVs 3.1.637.3.1.4.10.18.5.1.9
The number of Line Code Violations (LCVs) en- countered by a DS1 interface in the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalLSESs 3.1.637.3.1.4.10.18.5.1.10
Number of Severely errored seconds (SES-L) at line level encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalLLOSSs 3.1.637.3.1.4.10.18.5.1.11
Number of seconds containing one or more LOS defects (LOSS-L) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalAESs 3.1.637.3.1.4.10.18.5.1.12
Number of errored seconds of type A at path level (ESA-P) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1DayIntervalAISSs 3.1.637.3.1.4.10.18.5.1.13
Number of seconds containing one or more AIS defects at path level (AISS-P) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndCurrentTable 3.1.637.3.1.4.10.18.6
The ADN DS1/E1 Far End Current table. This table is supported by CES-T1-ESF interfaces. This table refers to ANSI T1.231.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1FarEndCurrentEntry

adnDsx1FarEndCurrentEntry 3.1.637.3.1.4.10.18.6.1
An entry in the ADN Far End DS1/E1 Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1FarEndCurrentEntry  

adnDsx1FarEndCurrentAESs 3.1.637.3.1.4.10.18.6.1.1
Number of errored seconds of type A at path level (ESA) encountered by the remote equipment during the current 15-minute interval. Common Name: Errored Seconds of type A
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndIntervalTable 3.1.637.3.1.4.10.18.7
The ADN DS1/E1 Far End Interval table. This table is supported by CES-T1-ESF interfaces. This table refers to ANSI T1.231.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1FarEndIntervalEntry

adnDsx1FarEndIntervalEntry 3.1.637.3.1.4.10.18.7.1
An entry in the ADN Far End DS1/E1 Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1FarEndIntervalEntry  

adnDsx1FarEndIntervalNumber 3.1.637.3.1.4.10.18.7.1.1
A number which identifies the interval for which the set of statistics is available. The previous 24-hour period is divided into 96 15-minute intervals. The interval identified by 1 is the most recently completed 15-minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnDsx1FarEndIntervalAESs 3.1.637.3.1.4.10.18.7.1.2
Number of errored seconds of type A at path level (ESA) encountered by the remote equipment during the current 15-minute interval. Common Name: Errored Seconds of type A
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndDayIntervalTable 3.1.637.3.1.4.10.18.8
The ADN DS1/E1 Far End Day Interval table. This table is supported by CES-T1-ESF interfaces. This table refers to ANSI T1.231.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1FarEndDayIntervalEntry

adnDsx1FarEndDayIntervalEntry 3.1.637.3.1.4.10.18.8.1
An entry in the ADN Far End DS1/E1 Day Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1FarEndDayIntervalEntry  

adnDsx1FarEndDayIntervalESs 3.1.637.3.1.4.10.18.8.1.1
The number of Far End Errored Seconds (ES) encoun- tered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndDayIntervalSESs 3.1.637.3.1.4.10.18.8.1.2
The number of Far End Severely Errored Seconds (SES) encountered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndDayIntervalSEFSs 3.1.637.3.1.4.10.18.8.1.3
The number of Far End Severely Errored Framing Seconds (SEFS) encountered by a DS1 interface in the cuurent day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndDayIntervalUASs 3.1.637.3.1.4.10.18.8.1.4
The number of Far End Unavailable Seconds (UAS) encountered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndDayIntervalCSSs 3.1.637.3.1.4.10.18.8.1.5
The number of Far End Controlled Slip Seconds (CSS) encountered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndDayIntervalPCVs 3.1.637.3.1.4.10.18.8.1.6
The number of Far End Path Coding Violations (PCV) reported via the far end block error count en- countered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndDayIntervalLESs 3.1.637.3.1.4.10.18.8.1.7
The number of Far End Line Errored Seconds (LES) en- countered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndDayIntervalBESs 3.1.637.3.1.4.10.18.8.1.8
The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1FarEndDayIntervalAESs 3.1.637.3.1.4.10.18.8.1.9
Number of errored seconds of type A at path level (ESA) encountered by the remote equipment during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuCurrentTable 3.1.637.3.1.4.10.18.9
The ADN DS1/E1 Current Itu table. This table is supported by CES-E1 interfaces. This table refers to ITU G.826.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1ItuCurrentEntry

adnDsx1ItuCurrentEntry 3.1.637.3.1.4.10.18.9.1
An entry in the ADN DS1/E1 Current Itu table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1ItuCurrentEntry  

adnDsx1ItuCurrentESs 3.1.637.3.1.4.10.18.9.1.1
Number of errored seconds (ES) encountered during the current 15-minute interval. Common Name: Errored Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuCurrentSESs 3.1.637.3.1.4.10.18.9.1.2
Number of severely errored seconds (SES) encountered during the current 15-minute interval. Common Name: Severely Errored Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuCurrentBBEs 3.1.637.3.1.4.10.18.9.1.3
Number of background errored blocks (BBE) encountered during the current 15-minute interval. Common Name: Background Errored Blocks
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuFarEndCurrentESs 3.1.637.3.1.4.10.18.9.1.4
Number of errored seconds (ES) encountered by the remote equipment during the current 15-minute interval. Common Name: Remote Errored Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuFarEndCurrentSESs 3.1.637.3.1.4.10.18.9.1.5
Number of severely errored seconds (SES) encountered by the remote equipment during the current 15-minute interval. Common Name: Remote Severely Errored Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuFarEndCurrentBBEs 3.1.637.3.1.4.10.18.9.1.6
Number of background errored blocks (BBE) encountered by the remote equipment during the current 15-minute interval. Common Name: Remote Background Errored Blocks
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuCurrentUASs 3.1.637.3.1.4.10.18.9.1.7
The number of unavailable seconds (UAS) encountered during the current 15-minute interval. Common Name: Unavailable Time
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuIntervalTable 3.1.637.3.1.4.10.18.10
The ADN DS1/E1 Itu Interval table. This table is supported by CES-E1 interfaces. This table refers to ITU G.826.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1ItuIntervalEntry

adnDsx1ItuIntervalEntry 3.1.637.3.1.4.10.18.10.1
An entry in the ADN DS1/E1 Interval Itu table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1ItuIntervalEntry  

adnDsx1ItuIntervalNumber 3.1.637.3.1.4.10.18.10.1.1
A number which identifies the interval for which the set of statistics is available. The previous 24-hour period is divided into 96 15-minute intervals. The interval identified by 1 is the most recently completed 15-minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnDsx1ItuIntervalESs 3.1.637.3.1.4.10.18.10.1.2
Number of errored seconds (ES) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuIntervalSESs 3.1.637.3.1.4.10.18.10.1.3
Number of severely errored seconds (SES) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuIntervalBBEs 3.1.637.3.1.4.10.18.10.1.4
Number of background errored blocks (BBE) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuFarEndIntervalESs 3.1.637.3.1.4.10.18.10.1.5
Number of errored seconds (ES) encountered by the remote equipment during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuFarEndIntervalSESs 3.1.637.3.1.4.10.18.10.1.6
Number of severely errored seconds (SES) encountered by the remote equipment during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuFarEndIntervalBBEs 3.1.637.3.1.4.10.18.10.1.7
Number of background errored blocks (BBE) encountered by the remote equipment during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuIntervalUASs 3.1.637.3.1.4.10.18.10.1.8
Number of unavailable seconds (UAS) encountered in a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuDayIntervalTable 3.1.637.3.1.4.10.18.11
The ADN DS1/E1 Itu Day Interval table. This table is supported by CES-E1 interfaces. This table refers to ITU G.826.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnDsx1ItuDayIntervalEntry

adnDsx1ItuDayIntervalEntry 3.1.637.3.1.4.10.18.11.1
An entry in the DS1/E1 Day Itu table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnDsx1ItuDayIntervalEntry  

adnDsx1ItuDayIntervalESs 3.1.637.3.1.4.10.18.11.1.1
Number of errored seconds (ES) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuDayIntervalSESs 3.1.637.3.1.4.10.18.11.1.2
Number of severely errored seconds (SES) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuDayIntervalBBEs 3.1.637.3.1.4.10.18.11.1.3
Number of background errored blocks (BBE) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuFarEndDayIntervalESs 3.1.637.3.1.4.10.18.11.1.4
Number of errored seconds (ES) encountered by the remote equipment during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuFarEndDayIntervalSESs 3.1.637.3.1.4.10.18.11.1.5
Number of severely errored seconds (SES) encountered by the remote equipment during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuFarEndDayIntervalBBEs 3.1.637.3.1.4.10.18.11.1.6
Number of background errored blocks (BBE) encountered by the remote equipment during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDsx1ItuDayIntervalUASs 3.1.637.3.1.4.10.18.11.1.7
Number of unavailable seconds (UAS) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnDs3e3 3.1.637.3.1.4.10.30
OBJECT IDENTIFIER    

adnX3ConfigTable 3.1.637.3.1.4.10.30.1
This table is the extension of the dsx3ConfigTable described in the DS3/E3 standard MIB.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnX3ConfigEntry

adnX3ConfigEntry 3.1.637.3.1.4.10.30.1.1
An entry in the DS3/E3 Configuration table extension.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnX3ConfigEntry  

adnX3MsferfTest 3.1.637.3.1.4.10.30.1.1.1
This variable is used to send a constant yellow alarm signal at the frame level to the remote equipment. This object is used only for testing and debugging. Common Name: Forcing a Line FERF Signal
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adnX3LineFerfOn(1), adnX3LineFerfOff(2)  

adnX3PathferfTest 3.1.637.3.1.4.10.30.1.1.2
This variable is used to send a constant yellow alarm signal at the path level to the remote equipment. This object is used only for testing and debugging. Common Name: Forcing a Path FERF Signal
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adnX3PathFerfOn(1), adnX3PathFerfOff(2)  

adnX3AisTest 3.1.637.3.1.4.10.30.1.1.3
This variable is used to send a constant alarm indication signal (AIS) to the remote equipment. This object is used only for testing and debugging. Common Name: Forcing a Line Alarm Indication Signal
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adnX3LineAisOn(1), adnX3LineAisOff(2)  

adnX3Scramblerconfig 3.1.637.3.1.4.10.30.1.1.4
Defines if the DS3 Physical Layer Convergence Protocol (PLCP) scrambler is active or not. Common Name: D3 Scrambler
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER adnX3ScramblerOn(1), adnX3ScramblerOff(2)  

adnX3IdleCellFillingconfig 3.1.637.3.1.4.10.30.1.1.5
The type of cell rate decoupling (CRD) mode selected for the line: - unassigned cells, according to ATM Forum standard - idle cells, according to ITU standart. Common Name: Inserted Cell Type
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER adnX3UnassignedCell(1), adnX3IdleCell(2)  

adnX3LineStatus 3.1.637.3.1.4.10.30.1.1.6
This variable indicates the status of the line interface. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnX3NoAlarm bit should be set only if no other bit is set. The bit positions and their corresponding ATM core counter numbers # are: # Bit Value ------------------------------------------------------ . 1 adnX3NoAlarm . No alarm present 10 2 adnX3RcvRAIFailure . Receiving yellow/remote alarm (RAI) . indication . 4 adnX3reserved . Not used 2 8 adndsx3RcvAIS . Receiving alarm indication signals . (AIS) . 16 adnX3reserved . Not used 7 32 adnX3LOF . Receiving loss-of-frame (LOF) . signals 0 64 adnX3LOS . Receiving loss-of-signal (LOS) . 128 adnX3LoopbackState . Looping the received signal . 256 adnX3reserved . Not used 3 512 adnX3RcvFerfAlarm . Receiving Far End Receive Failures . (FERF) DS3 yellow alarm 4 1024 adnX3PbitError . P-bit parity error counter threshold . reached 5 2048 adnX3CbitError . C-bit parity error counter threshold . reached 6 4096 adnX3FEBEError . Far end block errors (FEBE) counter . threshold reached 9 8192 adnX3FEBEError -- obsolete -- . FEBE Physical Layer Convergence . Protocol (PLCP) counter threshold . reached 11 16384 adnX3BIP8Error -- obsolete -- . 8-bits interleaved parity (BIP-8) . counter threshold reached 12 32768 adnX3LOFPlcpError . LOF DS3 PLCP counter threshold . reached 16 65536 adnX3LOCDError . Loss-of-cell-delineation (LOCD) . counter threshold reached 17 131072 adnX3HECCorrected . Corrected Header Error Control (HEC) . counter threshold reached 18 262144 adnX3HECUncorrected . Uncorrected HEC counter threshold . reached 20 524288 adnX3OOFPlcpError -- obsolete -- . Out-of-frame (OOF) PLCP counter . threshold reached 21 1048576 adnX3LCVError -- obsolete -- . Line code violation (LCV) counter . threshold reached 22 2097152 adnX3UpwardsFIFO . Upwards cell buffer overflow 26 4194304 adnX3DownwardsFIFO -- obsolete -- . Downwards cell buffer overflow 28 8388608 adnX3IdleCode . Idle Code counter threshold reached 29 16777216 adnX3OOFError . OOF counter threshold reached 30 33554432 adnX3HBERError -- obsolete -- . High bit error rate (HBER) counter . threshold reached 31 67108864 adnX3ChangeMode . Change Mode counter threshold reached Common Name: Line Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnX3LinePerfStatus 3.1.637.3.1.4.10.30.1.1.7
This variable indicates the performance status of the interface. It is a bit map represented as a sum; therefore, it can represent multiple status simultaneously. The adnX3NoDefect bit should be set only if no other bit is set. The adnX3UnavailablePeriod indicates that the interface has entered an unavailable period. Each CrossingThreshold bit indicates that the corresponding performance counter has reached its threshold. The bit positions are: 1 adnX3NoDefect 2 adnX3UnavailablePeriod 4 adnX3CurrentCrossingThresholdESs 8 adnX3CurrentCrossingThresholdSESs 16 adnX3CurrentCrossingThresholdBBEs 32 adnX3CurrentCrossingThresholdFarEndESs 64 adnX3CurrentCrossingThresholdFarEndSESs 128 adnX3CurrentCrossingThresholdFarEndBBEs 256 adnX3CurrentCrossingThresholdUASs 512 adnX3DayCrossingThresholdESs 1024 adnX3DayCrossingThresholdSESs 2048 adnX3DayCrossingThresholdBBEs 4096 adnX3DayCrossingThresholdFarEndESs 8192 adnX3DayCrossingThresholdFarEndSESs 16384 adnX3DayCrossingThresholdFarEndBBEs 32768 adnX3DayCrossingThresholdUASs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnX3LineHWStatus 3.1.637.3.1.4.10.30.1.1.8
This variable indicates the hardware status of a line. The given status value corresponds to the last test initiated by setting the nominator ifTestType with adnIfTest- TypeLineHW test identifier. If the result of the test, given by the nominator ifTestResult, is different than 'success' or 'failed', the given status value is not significant. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnX3LineHWNoDefect bit should be set only if no other bit is set. If the status is not significant, all the bits are reset. The bit positions are: (BBT3B, BBT3B2, BBT3B3, or BBT3B4 boards): 1 adnX3LineHWNoDefect 2 BGPHT chip failure 4 BGP45 chip failure on line side 8 DS3 PLPP chip failure on line side 16 Applique failure (BBE3B, or BBE3B3 boards): 1 adnX3LineHWNoDefect 2 BGPHT chip failure 4 not used 8 BGP43 chip failure on line side 16 MRT chip failure (BBTP3C board with HATT3C applique): 1 adnX3LineHWNoDefect 2 not used 4 not used 8 PM7346 chip failure on line side 16 applique failure (BBTP3C board with HATE3C applique): 1 adnX3LineHWNoDefect 2 not used 4 BGP45 chip failure on line side 8 PM7346 chip failure on line side 16 applique failure
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnX3CounterTable 3.1.637.3.1.4.10.30.2
The DS3/E3 ADN Counter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnX3CounterEntry

adnX3CounterEntry 3.1.637.3.1.4.10.30.2.1
An entry in the DS3/E3 ADN Counter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnX3CounterEntry  

adnX3LOSCounter 3.1.637.3.1.4.10.30.2.1.1
Duration of loss-of-signal (LOS). Counter #0 of the ATM core, only available on BBT3Bx, BBE3Bx and BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3AISCounter 3.1.637.3.1.4.10.30.2.1.2
Duration of alarm indication signal (AIS). Counter #2 of the ATM core, only available on BBT3Bx, BBE3Bx and BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3YellowAlarmCounter 3.1.637.3.1.4.10.30.2.1.3
Duration of far end received failure (FERF) received from the remote equipment at DS3 level. FERF is also called remote alarm indication (RAI) or received yellow alarm. Counter #3 of the ATM core, only available on BBT3Bx boards and BBTP3C board with HATT3C applique.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3PBitCounter 3.1.637.3.1.4.10.30.2.1.4
Number of P-bit parity errors. Counter #4 of the ATM core, only available on BBT3Bx boards and BBTP3C board with HATT3C applique.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3CBitCounter 3.1.637.3.1.4.10.30.2.1.5
Number of C-bit parity errors. Counter #5 of the ATM core, only available on BBT3Bx boards and BBTP3C board with HATT3C applique.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3CBitFebeCounter 3.1.637.3.1.4.10.30.2.1.6
Number of C-bit far end block errors (FEBE). Counter #6 of the ATM core, only available on BBT3Bx boards and BBTP3C board with HATT3C applique.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3LOFCounter 3.1.637.3.1.4.10.30.2.1.7
Duration of loss-of-frame (LOF). Counter #7 of the ATM core, only available on BBT3Bx, BBE3Bx and BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3LCVCounter 3.1.637.3.1.4.10.30.2.1.8
Number of line code violations (LCV). Counter #21 of the ATM core, only available on BBT3Bx boards and BBTP3C board with HATT3C applique. Common Name: Line Code Viol
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3FebeCounter 3.1.637.3.1.4.10.30.2.1.9
Number of far end block errors (FEBE). Counter #9 of the ATM core, only available on BBE3Bx boards and BBTP3C board with HATE3C applique.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3PathferfCounter 3.1.637.3.1.4.10.30.2.1.10
Duration of far end received failure (FERF) received from the remote equipment at path level. FERF is also called remote alarm indication (RAI) or received yellow alarm. Counter #10 of the ATM core, only available on BBE3Bx boards and BBTP3C board with HATE3C applique.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3Bip8Counter 3.1.637.3.1.4.10.30.2.1.11
Number of 8-bits interleaved parity (BIP-8) errors. Counter #11 of the ATM core, only available on BBE3Bx boards and BBTP3C board with HATE3C applique.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3OOFCounter 3.1.637.3.1.4.10.30.2.1.12
Number of out-of-frame (OOF) errors. Counter #29 of the ATM core, only available on BBT3Bx, BBE3Bx and BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3HECCorrectedCounter 3.1.637.3.1.4.10.30.2.1.13
Number of cells corrected through Header Error Control (HEC) mechanisms. Counter #17 of the ATM core, only available on BBE3B board.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnX3HECUncorrectedCounter 3.1.637.3.1.4.10.30.2.1.14
Number of cells discarded through Header Error Control (HEC) mechanisms. Counter #18 of the ATM core, only available on BBT3B and BBE3B boards.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnX3UpwardsFIFOCounter 3.1.637.3.1.4.10.30.2.1.15
Number of upward (from remote equipment) cell buffer overflow events, only available on BBT3B and BBE3B boards. Counter #22 of the ATM core
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnX3DownwardsFIFOCounter 3.1.637.3.1.4.10.30.2.1.16
Number of downward (to remote equipment) cell buffer overflow events, only available on BBT3B and BBE3B boards. Counter #26 of the ATM core
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnX3HBERCounter 3.1.637.3.1.4.10.30.2.1.17
Duration of high bit error rate (HBER). Counter #30 of the ATM core, only available on BBT3B board.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnX3IdleCodeCounter 3.1.637.3.1.4.10.30.2.1.18
Duration of idle code reception. Counter #28 of the ATM core, only available on BBT3Bx boards and BBTP3C board with HATT3C applique.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3LOCDCounter 3.1.637.3.1.4.10.30.2.1.19
Duration of loss-of-cell-delineation (LOCD). Counter #16 of the ATM core, only available on BBT3B and BBE3B boards.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnX3ModeChangeCounter 3.1.637.3.1.4.10.30.2.1.20
Duration of DS3 application mode change. Counter #31 of the ATM core, only available on BBT3Bx boards and BBTP3C board with HATT3C applique.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnX3PlcpLOFCounter 3.1.637.3.1.4.10.30.2.1.21
Duration of loss-of-frame (LOF) at the Physical Layer Convergence Protocol (PLCP) level. Counter #12 of the ATM core, only available on BBT3B board.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnX3PlcpOOFCounter 3.1.637.3.1.4.10.30.2.1.22
Number of out-of-frame (OOF) events at the Physical Layer Convergence Protocol (PLCP) level. Counter #20 of the ATM core, only available on BBT3B board.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnX3CurrentTable 3.1.637.3.1.4.10.30.3
The DS3/E3 Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnX3CurrentEntry

adnX3CurrentEntry 3.1.637.3.1.4.10.30.3.1
An entry in the DS3/E3 Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnX3CurrentEntry  

adnX3CurrentESs 3.1.637.3.1.4.10.30.3.1.1
Number of errored seconds (ES) encountered during the current 15-minute interval. Common Name: Errored Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3CurrentSESs 3.1.637.3.1.4.10.30.3.1.2
Number of severely errored seconds (SES) encountered during the current 15-minute interval. Common Name: Severely Errored Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3CurrentBBEs 3.1.637.3.1.4.10.30.3.1.3
Number of background errored blocks (BBE) encountered during the current 15-minute interval. Common Name: Background Errored Blocks
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3CurrentFarEndESs 3.1.637.3.1.4.10.30.3.1.4
Number of errored seconds (ES) encountered by the remote equipment during the current 15-minute interval. Common Name: Remote Errored Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3CurrentFarEndSESs 3.1.637.3.1.4.10.30.3.1.5
Number of severely errored seconds (SES) encountered by the remote equipment during the current 15-minute interval. Common Name: Remote Severely Errored Seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3CurrentFarEndBBEs 3.1.637.3.1.4.10.30.3.1.6
Number of background errored blocks (BBE) encountered by the remote equipment during the current 15-minute interval. Common Name: Remote Background Errored Blocks
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3CurrentUASs 3.1.637.3.1.4.10.30.3.1.7
The number of unavailable seconds (UAS) encountered during the current 15-minute interval. Common Name: Unavailable Time
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3IntervalTable 3.1.637.3.1.4.10.30.4
The DS3/E3 Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnX3IntervalEntry

adnX3IntervalEntry 3.1.637.3.1.4.10.30.4.1
An entry in the DS3/E3 Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnX3IntervalEntry  

adnX3IntervalNumber 3.1.637.3.1.4.10.30.4.1.1
A number which identifies the interval for which the set of statistics is available. The previous 24-hour period is divided into 96 15-minute intervals. The interval identified by 1 is the most recently completed 15-minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnX3IntervalESs 3.1.637.3.1.4.10.30.4.1.2
Number of errored seconds (ES) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3IntervalSESs 3.1.637.3.1.4.10.30.4.1.3
Number of severely errored seconds (SES) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3IntervalBBEs 3.1.637.3.1.4.10.30.4.1.4
Number of background errored blocks (BBE) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3IntervalFarEndESs 3.1.637.3.1.4.10.30.4.1.5
Number of errored seconds (ES) encountered by the remote equipment during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3IntervalFarEndSESs 3.1.637.3.1.4.10.30.4.1.6
Number of severely errored seconds (SES) encountered by the remote equipment during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3IntervalFarEndBBEs 3.1.637.3.1.4.10.30.4.1.7
Number of background errored blocks (BBE) encountered by the remote equipment during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3IntervalUASs 3.1.637.3.1.4.10.30.4.1.8
Number of unavailable seconds (UAS) encountered in a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3DayTable 3.1.637.3.1.4.10.30.5
The DS3/E3 Day table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnX3DayEntry

adnX3DayEntry 3.1.637.3.1.4.10.30.5.1
An entry in the DS3/E3 Day table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnX3DayEntry  

adnX3DayESs 3.1.637.3.1.4.10.30.5.1.1
Number of errored seconds (ES) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3DaySESs 3.1.637.3.1.4.10.30.5.1.2
Number of severely errored seconds (SES) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3DayBBEs 3.1.637.3.1.4.10.30.5.1.3
Number of background errored blocks (BBE) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3DayFarEndESs 3.1.637.3.1.4.10.30.5.1.4
Number of errored seconds (ES) encountered by the remote equipment during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3DayFarEndSESs 3.1.637.3.1.4.10.30.5.1.5
Number of severely errored seconds (SES) encountered by the remote equipment during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3DayFarEndBBEs 3.1.637.3.1.4.10.30.5.1.6
Number of background errored blocks (BBE) encountered by the remote equipment during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3DayUASs 3.1.637.3.1.4.10.30.5.1.7
Number of unavailable seconds (UAS) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3TotalTable 3.1.637.3.1.4.10.30.6
The DS3/E3 Total table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnX3TotalEntry

adnX3TotalEntry 3.1.637.3.1.4.10.30.6.1
An entry in the DS3/E3 Total table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnX3TotalEntry  

adnX3TotalESs 3.1.637.3.1.4.10.30.6.1.1
Number of errored seconds (ES) encountered during the 24-hour reporting period. It is the sum of ES statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3TotalSESs 3.1.637.3.1.4.10.30.6.1.2
Number of severely errored seconds (SES) encountered during the 24-hour reporting period. It is the sum of SES statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3TotalBBEs 3.1.637.3.1.4.10.30.6.1.3
Number of background errored blocks (BBE) encountered during the 24-hour reporting period. It is the sum of BBE statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3TotalFarEndESs 3.1.637.3.1.4.10.30.6.1.4
Number of errored seconds (ES) encountered by the remote equipment during the 24-hour reporting period. It is the sum of Far End ES statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3TotalFarEndSESs 3.1.637.3.1.4.10.30.6.1.5
Number of severely errored seconds (SES) encountered by the remote equipment during the 24-hour reporting period. It is the sum of Far End SES statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3TotalFarEndBBEs 3.1.637.3.1.4.10.30.6.1.6
Number of background errored blocks (BBE) encountered by the remote equipment during the 24-hour reporting period. It is the sum of Far End BBE statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnX3TotalUASs 3.1.637.3.1.4.10.30.6.1.7
Number of unavailable seconds (UAS) encountered during the 24-hour reporting period. It is the sum of UAS statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetMIB 3.1.637.3.1.4.10.39
OBJECT IDENTIFIER    

adnsonetObjects 3.1.637.3.1.4.10.39.1
OBJECT IDENTIFIER    

adnsonetObjectsPath 3.1.637.3.1.4.10.39.2
OBJECT IDENTIFIER    

adnsonetObjectsTC 3.1.637.3.1.4.10.39.3
OBJECT IDENTIFIER    

adnsonetObjectsITUperf 3.1.637.3.1.4.10.39.4
OBJECT IDENTIFIER    

adnsonetObjectsMaintenance 3.1.637.3.1.4.10.39.5
OBJECT IDENTIFIER    

adnsonetMedium 3.1.637.3.1.4.10.39.1.1
OBJECT IDENTIFIER    

adnsonetSection 3.1.637.3.1.4.10.39.1.2
OBJECT IDENTIFIER    

adnsonetLine 3.1.637.3.1.4.10.39.1.3
OBJECT IDENTIFIER    

adnsonetPath 3.1.637.3.1.4.10.39.2.1
OBJECT IDENTIFIER    

adnsonetTC 3.1.637.3.1.4.10.39.3.1
OBJECT IDENTIFIER    

adnsonetITUperf 3.1.637.3.1.4.10.39.4.1
OBJECT IDENTIFIER    

adnsonetFarEndITUperf 3.1.637.3.1.4.10.39.4.2
OBJECT IDENTIFIER    

adnsonetMaintenance 3.1.637.3.1.4.10.39.5.1
OBJECT IDENTIFIER    

adnsonetMediumTable 3.1.637.3.1.4.10.39.1.1.1
The ADN SONET/SDH Medium table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetMediumEntry

adnsonetMediumEntry 3.1.637.3.1.4.10.39.1.1.1.1
An entry in the ADN SONET/SDH Medium table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetMediumEntry  

adnsonetMediumStatus 3.1.637.3.1.4.10.39.1.1.1.1.1
This variable indicates the status of the interface. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnsonetMediumNoDefect bit should be set only if no other bit is set. The bit positions are: 1 adnsonetMediumNoDefect 2 adnsonetMediumLaserDegradation 4 adnsonetMediumLaserTransmitSignalOut 8 adnsonetMediumAppliqueFailure (obsolete) Common Name: Medium State
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnsonetMediumLaserDegradation 3.1.637.3.1.4.10.39.1.1.1.1.2
Duration of laser degradation. Counter #23 of the ATM core, only available on BBS1Bx board with HAS1B applique and on BBTS1C board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetMediumLaserTransmitSignalOut 3.1.637.3.1.4.10.39.1.1.1.1.3
Duration of transmit signal out of range. Counter #24 of the ATM core, only available on BBS1Bx board with HAS1B applique and on BBTS1C board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetMediumAppliqueFailure 3.1.637.3.1.4.10.39.1.1.1.1.4
Duration of applique board failure. Counter #27 of the ATM core.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetMediumConfigLineClockMode 3.1.637.3.1.4.10.39.1.1.1.1.5
The transmit clock mode of the line: - local timing: the transmit clock is generated by the local board, - loop timing: the transmit clock is the one received from the remote equipment, - through timing: the transmit clock is derived from the recovered receive clock of another interface of the HSS. Common Name: Transmit Clock Mode
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adnsonetMediumLocalTiming(1), adnsonetMediumLoopTiming(2), adnsonetMediumThroughTiming(3)  

adnsonetMediumConfigLaserPower 3.1.637.3.1.4.10.39.1.1.1.1.6
The administrative status of the laser LED on the applique: - LaserON: laser LED in service with automatic laser shutdown (ALS) function disabled, - LaserOFF: laser LED out of service, - LaserNS: laser LED not supported by the applique, - LaserONALS: laser LED in service with ALS function enabled. Common Name: Laser Power
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adnsonetMediumLaserON(1), adnsonetMediumLaserOFF(2), adnsonetMediumLaserNS(3), adnsonetMediumLaserONALS(4)  

adnsonetSectionTable 3.1.637.3.1.4.10.39.1.2.1
The ADN SONET/SDH Section Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetSectionEntry

adnsonetSectionEntry 3.1.637.3.1.4.10.39.1.2.1.1
An entry in the ADN SONET/SDH Section Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetSectionEntry  

adnsonetSectionStatus 3.1.637.3.1.4.10.39.1.2.1.1.1
This variable indicates the status of the interface. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnsonetSectionNoDefect bit should be set only if no other bit is set. The bit positions are: 1 adnsonetSectionNoDefect 2 adnsonetSectionLOS 4 adnsonetSectionLOF 8 adnsonetSectionOOF Common Name: Section State
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnsonetSectionLOS 3.1.637.3.1.4.10.39.1.2.1.1.2
Duration of loss-of-signal (LOS). Counter #0 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetSectionLOF 3.1.637.3.1.4.10.39.1.2.1.1.3
Duration of loss-of-frame (LOF). Counter #7 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetSectionOOF 3.1.637.3.1.4.10.39.1.2.1.1.4
Number of out-of-frame (OOF) events. Counter #29 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetLineTable 3.1.637.3.1.4.10.39.1.3.1
The ADN SONET/SDH Line Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetLineEntry

adnsonetLineEntry 3.1.637.3.1.4.10.39.1.3.1.1
An entry in the ADN SONET/SDH Line Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetLineEntry  

adnsonetLineStatus 3.1.637.3.1.4.10.39.1.3.1.1.1
This variable indicates the status of the interface. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnsonetLineNoDefect bit should be set only if no other bit is set. The bit positions are: 1 adnsonetLineNoDefect 2 adnsonetLineAIS 4 adnsonetLineRDI 8 adnsonetLineBIP 16 adnsonetLineHighBIP Common Name: Line State
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnsonetLineAIS 3.1.637.3.1.4.10.39.1.3.1.1.2
Duration of alarm indication signal (AIS). Counter #2 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetLineRcvRDI 3.1.637.3.1.4.10.39.1.3.1.1.3
Duration of remote defect indication (RDI) received from the remote equipement. For a Synchronous Digital Hierarchy (SDH) line, the RDI signal is known as Multiplexing Section Far End Receive Failure (MS-FERF). Counter #3 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetLineBIP 3.1.637.3.1.4.10.39.1.3.1.1.4
Number of 24-bit interleaved parity (BIP-24) errors for STS-3c or STM-1. Number of 96-bit interleaved parity (BIP-96) errors for STS-12c or STM-4. Counter #28 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetLineConfigLoopback 3.1.637.3.1.4.10.39.1.3.1.1.5
This variable indicates if line loopback is activated or deactivated. When activated, received frames are retransmitted on the line. Common Name: Line Loopback
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adnsonetLineLoopbackON(1), adnsonetLineLoopbackOFF(2)  

adnsonetLineConfigRDI 3.1.637.3.1.4.10.39.1.3.1.1.6
This variable indicates if a permanent remote defect indication (RDI) or Far End Receive Failure (FERF) is sent on the line. It is a configuration option that should be used only for maintenance purposes. Common Name: Forcing a Line Remote Defect Indication
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adnsonetLineRDION(1), adnsonetLineRDIOFF(2)  

adnsonetLineConfigAIS 3.1.637.3.1.4.10.39.1.3.1.1.7
This variable indicates if a permanent alarm indication signal (AIS) can be sent on the line. For STM-1 interfaces, this option can't be activated (AIS off). For STS-3c, STS-12c, and STM-4 interfaces, this option can be activated (AIS off or AIS on). It is a configuration option that should be used only for maintenance purposes. Common Name: Forcing a Line Alarm Indication Signal
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adnsonetLineAISON(1), adnsonetLineAISOFF(2)  

adnsonetPathTable 3.1.637.3.1.4.10.39.2.1.1
The ADN SONET/SDH Path Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetPathEntry

adnsonetPathEntry 3.1.637.3.1.4.10.39.2.1.1.1
An entry in the ADN SONET/SDH Path Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetPathEntry  

adnsonetPathWidth 3.1.637.3.1.4.10.39.2.1.1.1.1
The type of Synchronous Optical Network/Synchronous Digital Hierarchy (SONET/SDH) path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sts3cSTM1(1), sts12cSTM4(2)  

adnsonetPathStatus 3.1.637.3.1.4.10.39.2.1.1.1.2
This variable indicates the status of the interface. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnsonetPathNoDefect bit should be set only if no other bit is set. The bit positions are: 1 adnsonetLineNoDefect 2 adnsonetPathSTSLOP 4 adnsonetPathSTSAIS 8 adnsonetPathSTSRDI 16 adnsonetPathUnequipped * 32 adnsonetPathSignalLabelMismatch * 64 adnsonetPathBIP8 128 adnsonetPathFEBE * not provided by HSS, but the value is required to ensure compatibility with the RFC sonetPathStatus.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnsonetPathLOP 3.1.637.3.1.4.10.39.2.1.1.1.3
Duration of loss-of-pointer (LOP). Counter #12 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetPathAIS 3.1.637.3.1.4.10.39.2.1.1.1.4
Duration of alarm indication signal (AIS) at path level. Counter #8 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetPathRcvRDI 3.1.637.3.1.4.10.39.2.1.1.1.5
Duration of remote defect indication (RDI) received from the remote equipment at path level. For Synchronous Digital Hierarchy (SDH), this signal is known as a path Far End Receive Failure (FERF) event. Counter #10 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetPathBIP8 3.1.637.3.1.4.10.39.2.1.1.1.6
Number of 8-bit interleaved parity (BIP-8) errors. Counter #11 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetPathFEBE 3.1.637.3.1.4.10.39.2.1.1.1.7
Number of far end block errors (FEBE) received from the remote equipment at path level. Counter #9 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetPathConfigRDI 3.1.637.3.1.4.10.39.2.1.1.1.8
This variable indicates if a permanent remote defect indication (RDI) is sent on the path. For Synchronous Digital Hierarchy (SDH), it indicates if a permanent Far End Receive Failure (FERF) can be sent on the path. This is a configuration option that should be used only for maintenance purposes. Common Name: Forcing a Path Remote Defect Indication
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adnsonetPathRDION(1), adnsonetPathRDIOFF(2)  

adnsonetPathConfigAIS 3.1.637.3.1.4.10.39.2.1.1.1.9
This variable indicates if a permanent alarm indication signal (AIS) is sent on the path. This is a configuration option that should be used only for maintenance purposes. Common Name: Forcing a Path Alarm Indication Signal
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER adnsonetPathAISON(1), adnsonetPathAISOFF(2)  

adnsonetTCTable 3.1.637.3.1.4.10.39.3.1.1
The ADN SONET/SDH Transmission Convergence (TC) Current table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetTCEntry

adnsonetTCEntry 3.1.637.3.1.4.10.39.3.1.1.1
An entry in the ADN SONET/SDH Transmission Convergence (TC) Current table.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  AdnSonetTCEntry  

adnsonetTCStatus 3.1.637.3.1.4.10.39.3.1.1.1.1
This variable indicates the status of the interface. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnsonetTCNoDefect bit should be set only if no other bit is set. The bit positions are: 1 adnsonetTCNoDefect 2 adnsonetTCOCD 4 adnsonetTCCorrectedHEC 8 adnsonetTCUnCorrectedHEC 16 adnsonetTCUpBufferOverflow 32 adnsonetTCDownBufferOverflow 64 adnsonetTCETtoLTLoss
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnsonetTCOCD 3.1.637.3.1.4.10.39.3.1.1.1.2
Duration of out-of-cell delineation (OCD). Counter #16 of the ATM core.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetTCCorrectedHEC 3.1.637.3.1.4.10.39.3.1.1.1.3
Number of cells corrected through Header Error Control (HEC) mechanisms. Counter #17 of the ATM core.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetTCUnCorrectedHEC 3.1.637.3.1.4.10.39.3.1.1.1.4
Number of cells discarded through Header Error Control (HEC) mechanisms. Counter #18 of the ATM core.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetTCUpBufferOverflow 3.1.637.3.1.4.10.39.3.1.1.1.5
Number of upward (from remote equipment) cell buffer overflow events. Counter #22 of the ATM core.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetTCDownBufferOverflow 3.1.637.3.1.4.10.39.3.1.1.1.6
Number of downward (to remote equipment) cell buffer overflow events. Counter #26 of the ATM core.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetTCETtoLTLoss 3.1.637.3.1.4.10.39.3.1.1.1.7
Duration of loss of ATM signal from exchange termination processor (ET) to linetermination processor (LT). Counter #25 of the ATM core.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnsonetTCConfigCRD 3.1.637.3.1.4.10.39.3.1.1.1.8
The type of cell rate decoupling (CRD) mode selected for the line: - unassigned cells (ANSI) - idle cells (ITU). Common Name: Cell Rate Decoupling
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER adnsonetTCUnassignedCell(1), adnsonetTCIdleCell(2)  

adnsonetCurrentTable 3.1.637.3.1.4.10.39.4.1.1
The ADN SONET/SDH Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetCurrentEntry

adnsonetCurrentEntry 3.1.637.3.1.4.10.39.4.1.1.1
An entry in the ADN SONET/SDH Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetCurrentEntry  

adnsonetCurrentESs 3.1.637.3.1.4.10.39.4.1.1.1.1
Number of errored seconds (ES) encountered during the current 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetCurrentSESs 3.1.637.3.1.4.10.39.4.1.1.1.2
Number of severely errored seconds (SES) encountered during the current 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetCurrentBBEs 3.1.637.3.1.4.10.39.4.1.1.1.3
Number of background errored blocks (BBE) encountered during the current 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetCurrentUASs 3.1.637.3.1.4.10.39.4.1.1.1.4
The number of unavailable seconds (UAS) encountered during the current 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetIntervalTable 3.1.637.3.1.4.10.39.4.1.2
The ADN SONET/SDH Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetIntervalEntry

adnsonetIntervalEntry 3.1.637.3.1.4.10.39.4.1.2.1
An entry in the ADN SONET/SDH Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetIntervalEntry  

adnsonetIntervalNumber 3.1.637.3.1.4.10.39.4.1.2.1.1
A number which identifies the interval for which the set of statistics is available. The previous 24-hour period is divided into 96 15-minute intervals. The interval identified by 1 is the most recently completed 15-minute interval and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnsonetIntervalESs 3.1.637.3.1.4.10.39.4.1.2.1.2
Number of errored seconds (ES) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetIntervalSESs 3.1.637.3.1.4.10.39.4.1.2.1.3
Number of severely errored seconds (SES) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetIntervalBBEs 3.1.637.3.1.4.10.39.4.1.2.1.4
Number of background errored blocks (BBE) encountered during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetIntervalUASs 3.1.637.3.1.4.10.39.4.1.2.1.5
Number of unavailable seconds (UAS) encountered in a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetTotalTable 3.1.637.3.1.4.10.39.4.1.3
The ADN SONET/SDH Total table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetTotalEntry

adnsonetTotalEntry 3.1.637.3.1.4.10.39.4.1.3.1
An entry in the ADN SONET/SDH Total table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetTotalEntry  

adnsonetTotalESs 3.1.637.3.1.4.10.39.4.1.3.1.1
Number of errored seconds (ES) encountered during the 24-hour reporting period. It is the sum of ES statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetTotalSESs 3.1.637.3.1.4.10.39.4.1.3.1.2
Number of severely errored seconds (SES) encountered during the 24-hour reporting period. It is the sum of SES statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetTotalBBEs 3.1.637.3.1.4.10.39.4.1.3.1.3
Number of background errored blocks (BBE) encountered during the 24-hour reporting period. It is the sum of BBE statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetTotalUASs 3.1.637.3.1.4.10.39.4.1.3.1.4
Number of unavailable seconds (UAS) encountered during the 24-hour reporting period. It is the sum of UAS statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetDayTable 3.1.637.3.1.4.10.39.4.1.4
The ADN SONET/SDH Day table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetDayEntry

adnsonetDayEntry 3.1.637.3.1.4.10.39.4.1.4.1
An entry in the ADN SONET/SDH Day table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetDayEntry  

adnsonetDayESs 3.1.637.3.1.4.10.39.4.1.4.1.1
Number of errored seconds (ES) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetDaySESs 3.1.637.3.1.4.10.39.4.1.4.1.2
Number of severely errored seconds (SES) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetDayBBEs 3.1.637.3.1.4.10.39.4.1.4.1.3
Number of background errored blocks (BBE) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetDayUASs 3.1.637.3.1.4.10.39.4.1.4.1.4
Number of unavailable seconds (UAS) encountered during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndCurrentTable 3.1.637.3.1.4.10.39.4.2.1
The ADN SONET/SDH Far End Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetFarEndCurrentEntry

adnsonetFarEndCurrentEntry 3.1.637.3.1.4.10.39.4.2.1.1
An entry in the ADN SONET/SDH Far End Current table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetFarEndCurrentEntry  

adnsonetFarEndCurrentESs 3.1.637.3.1.4.10.39.4.2.1.1.1
Number of errored seconds (ES) encountered by the remote equipment during the current 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndCurrentSESs 3.1.637.3.1.4.10.39.4.2.1.1.2
Number of severely errored seconds (SES) encountered by the remote equipment during the current 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndCurrentBBEs 3.1.637.3.1.4.10.39.4.2.1.1.3
Number of background errored blocks (BBE) encountered by the remote equipment during the current 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndIntervalTable 3.1.637.3.1.4.10.39.4.2.2
The ADN SONET/SDH Far End Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetFarEndIntervalEntry

adnsonetFarEndIntervalEntry 3.1.637.3.1.4.10.39.4.2.2.1
An entry in the ADN SONET/SDH Far End Interval table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetFarEndIntervalEntry  

adnsonetFarEndIntervalNumber 3.1.637.3.1.4.10.39.4.2.2.1.1
A number which identifies the interval for which the set of statistics is available. The previous 24-hour period is divided into 96 15-minute intervals. The interval identified by 1 is the most recently completed 15-minute interval and the interval identified by N is the interval immediately preceding the one identified by N-1.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnsonetFarEndIntervalESs 3.1.637.3.1.4.10.39.4.2.2.1.2
Number of errored seconds (ES) encountered by the remote equipment during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndIntervalSESs 3.1.637.3.1.4.10.39.4.2.2.1.3
Number of severely errored seconds (SES) encountered by the remote equipment during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndIntervalBBEs 3.1.637.3.1.4.10.39.4.2.2.1.4
Number of background errored blocks (BBE) encountered by the remote equipment during a particular 15-minute interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndTotalTable 3.1.637.3.1.4.10.39.4.2.3
The ADN SONET/SDH Far End Total table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetFarEndTotalEntry

adnsonetFarEndTotalEntry 3.1.637.3.1.4.10.39.4.2.3.1
An entry in the ADN SONET/SDH Far End Total table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetFarEndTotalEntry  

adnsonetFarEndTotalESs 3.1.637.3.1.4.10.39.4.2.3.1.1
Number of errored seconds (ES) encountered by the remote equipment during the 24-hour reporting period. It is the sum of Far End ES statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndTotalSESs 3.1.637.3.1.4.10.39.4.2.3.1.2
Number of severely errored seconds (SES) encountered by the remote equipment during the 24-hour reporting period. It is the sum of Far End SES statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndTotalBBEs 3.1.637.3.1.4.10.39.4.2.3.1.3
Number of background errored blocks (BBE) encountered by the remote equipment during the 24-hour reporting period. It is the sum of Far End BBE statistics for the 96 15-minute intervals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndDayTable 3.1.637.3.1.4.10.39.4.2.4
The ADN SONET/SDH Far End Day table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetFarEndDayEntry

adnsonetFarEndDayEntry 3.1.637.3.1.4.10.39.4.2.4.1
An entry in the ADN SONET/SDH Far End Day table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetFarEndDayEntry  

adnsonetFarEndDayESs 3.1.637.3.1.4.10.39.4.2.4.1.1
Number of errored seconds (ES) encountered by the remote equipment during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndDaySESs 3.1.637.3.1.4.10.39.4.2.4.1.2
Number of severely errored seconds (SES) encountered by the remote equipment during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetFarEndDayBBEs 3.1.637.3.1.4.10.39.4.2.4.1.3
Number of background errored blocks (BBE) encountered by the remote equipment during the current day (from 0 hours to the current time).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnsonetMaintenanceTable 3.1.637.3.1.4.10.39.5.1.1
The ADN SONET/SDH Maintenance table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnSonetMaintenanceEntry

adnsonetMaintenanceEntry 3.1.637.3.1.4.10.39.5.1.1.1
An entry in the ADN SONET/SDH Maintenance table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnSonetMaintenanceEntry  

adnsonetLineHWStatus 3.1.637.3.1.4.10.39.5.1.1.1.1
This variable indicates the hardware status of a line. The given status value corresponds to the last test initiated by setting the nominator ifTestType with adnIfTest- TypeLineHW test identifier. If the result of the test, given by the nominator ifTestResult, is different than 'success' or 'failed', the given status value is not significant. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnsonetLineHWNoDefect bit should be set only if no other bit is set. If the status is not significant, all the bits are reset. The bit positions are : (BBTS1C board): 1 adnsonetLineHWNoDefect 2 not used 4 not used 8 PM5357 chip failure at line side 16 applique failure (BBS1B, BBS1B3, BBS1B2, or BBS1B4 boards): 1 adnsonetLineHWNoDefect 2 BGPHT chip failure 4 BGS1B chip failure at ET side 8 BGS1B chip failure at line side 16 applique failure (BBS4B, or BBS4B2 boards): 1 adnsonetLineHWNoDefect 2 BGPHT chip failure 4 not used 8 PM5355 chip failure at line side 16 applique failure
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnsonetLinePerfStatus 3.1.637.3.1.4.10.39.5.1.1.1.2
This variable indicates the performance status of the interface. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnsonetNoDefect bit should be set only if no other bit is set. The adnsonetUnavailablePeriod bit indicates that the interface has entered an unavailable period. Each CrossingThreshold bit indicates that the corresponding performance counter has reached its threshold. The bit positions are: 1 adnsonetNoDefect 2 adnsonetUnavailablePeriod 4 adnsonetCurrentCrossingThresholdESs 8 adnsonetCurrentCrossingThresholdSESs 16 adnsonetCurrentCrossingThresholdBBEs 32 adnsonetCurrentCrossingThresholdFarEndESs 64 adnsonetCurrentCrossingThresholdFarEndSESs 128 adnsonetCurrentCrossingThresholdFarEndBBEs 256 adnsonetCurrentCrossingThresholdUASs 512 adnsonetDayCrossingThresholdESs 1024 adnsonetDayCrossingThresholdSESs 2048 adnsonetDayCrossingThresholdBBEs 4096 adnsonetDayCrossingThresholdFarEndESs 8192 adnsonetDayCrossingThresholdFarEndSESs 16384 adnsonetDayCrossingThresholdFarEndBBEs 32768 adnsonetDayCrossingThresholdUASs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmMIB 3.1.637.3.1.4.37
OBJECT IDENTIFIER    

adnAtmMIBObjects 3.1.637.3.1.4.37.1
OBJECT IDENTIFIER    

adnAtmLogLineTable 3.1.637.3.1.4.37.1.1
This table describes the logical line supporting the logical inter-node ATM interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmLogLineEntry

adnAtmLogLineEntry 3.1.637.3.1.4.37.1.1.1
An entry in the adnAtmLogLineTable. There is one entry for each logical line.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmLogLineEntry  

adnAtmLogLineVuniIfIndex 3.1.637.3.1.4.37.1.1.1.1
The ifIndex of the Virtual-User Network Interface (V-UNI) associated with this logical line. Common Name: V-UNI ifIndex
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnAtmLogLineVuniVpi 3.1.637.3.1.4.37.1.1.1.2
The Virtual Path Identifier (VPI) on the Virtual-User Network Interface (V-UNI) associated with this logical line. This VPI is unique to this logical line and is used as the logical line number. Common Name: Logical Line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceConfTable 3.1.637.3.1.4.37.1.2
This table is the extension of the atmInterfaceConfTable table, described in RFC 1695. This table contains proprietary ATM interface configuration parameters, one entry per ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmInterfaceConfEntry

adnAtmInterfaceConfEntry 3.1.637.3.1.4.37.1.2.1
An entry in the adnAtmInterfaceConfTable. There is one entry for each ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmInterfaceConfEntry  

adnAtmInterfaceLowLayerIfIndex 3.1.637.3.1.4.37.1.2.1.1
The ifIndex of the logical or physical line supporting this ATM interface. The line is considered to be the lower layer of the ATM interface. Common Name: Lower Layer Interface Index
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnAtmInterfaceType 3.1.637.3.1.4.37.1.2.1.2
The type of ATM interface: - 'externalUni': On an High Speed Coupler (HSC) line - 'nni': On a HSC line, connected to a Virtual Path (VP) switched network - 'internalUniSig': On a Cell Interconnection Gateway (CIG) internal line used for special connections such as routing, signalling and ILMI - 'virtualUni': Logical interface supporting the Virtual Path Connection (VPC) used to support the logical Cell alcatel Network protocol Interfaces (CNIs) - 'physicalCni': Inter-node physical interface (on a HSC line) - 'routlogicalCni': Routable logical CNI, supported by a logical line (inter-node VPC) - 'nonroutlogicalCni': Non-routable logical CNI, known only by path select - 'nonroutlogicalCniendtoend': Non-routable logical CNI; end-to-end identical to previous one but disallowed for transit Virtual Channel Connections (VCCs) - 'internalUni': On a board internal line (e.g. Circuit Emulation Service (CES) board). - 'tdpAccess': Tag Distribution Protocol (TDP) capable access. It can be a regular Tag Edge Router (TER) or a Tag Switch Controller (TSC). It is supported by an ATM logical line - 'tdpTrunk': TDP capable trunk. It is supported by an ATM logical line. Common Name: Interface Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER externalUni(1), nni(2), internalUniSig(3), virtualUni(4), physicalCni(5), routlogicalCni(6), nonroutlogicalCni(7), nonroutlogicalCniendtoend(8), internalUni(9), tdpAccess(10), tdpTrunk(11)  

adnAtmInterfaceMaxFillingRate 3.1.637.3.1.4.37.1.2.1.3
The maximum filling rate on this ATM interface. This value is the percentage of data that can be loaded on the line. For example, if the ifspeed is 100000 Mbits and the maximum filling rate is 80%, the total bandwidth allowed on the line is 80000 Mbits. When the maximum filling rate is reached, no more calls are accepted on the ATM interface. Common Name: Filling Rate (%)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceBWThreshold1 3.1.637.3.1.4.37.1.2.1.4
The ATM interface's higher bandwidth threshold, used for path selection on the Cell alcatel Network protocol Interface (CNI) to calculate actual available bandwidth. The value, expressed as a percentage, is significant only if this is a CNI; otherwise, it is 0. Common Name: Higher Bandwidth Threshold
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceBWThreshold2 3.1.637.3.1.4.37.1.2.1.5
The ATM interface's medium bandwidth threshold, used for path selection on the Cell alcatel Network protocol Interface (CNI) to calculate actual available bandwidth. The value, expressed as a percentage, is significant only if this is a CNI; otherwise, it is 0. Common Name: Medium Bandwidth Threshold
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceBWThreshold3 3.1.637.3.1.4.37.1.2.1.6
The ATM interface's lower bandwidth threshold, used for path selection on the Cell alcatel Network protocol Interface (CNI) to calculate actual available bandwidth. The value, expressed as a percentage, is significant only if this is a CNI; otherwise, it is 0. Common Name: Lower Bandwidth Threshold
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxPtpVcs 3.1.637.3.1.4.37.1.2.1.7
The maximum number of point-to-point Virtual Connections (VCs) (Virtual Path Connections (VPCs) and Virtual Channel Connections (VCCs)) on this ATM interface. Common Name: Max Point-to-Point Virtual Connections
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxPtMCc 3.1.637.3.1.4.37.1.2.1.8
The maximum number of point-to-multipoint cross-connections on this ATM interface. Common Name: Max Point-to-Multipoint Cross Connections
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxPvcc 3.1.637.3.1.4.37.1.2.1.9
The maximum number of permanent Virtual Channel Connections (VCCs) on this ATM interface. Common Names: Max Permanent VCCs, Max P-VCCs
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxSvcc 3.1.637.3.1.4.37.1.2.1.10
The maximum number of switched Virtual Channel Connections (VCCs) on this ATM interface. Common Names: Max Switched VCCs, Max S-VCCs
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceVccLowVpi 3.1.637.3.1.4.37.1.2.1.11
The low value of the Virtual Path Identifier (VPI) range dedicated to Virtual Channel (VC) switching on this ATM interface. Common Name: Low VPI Value
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceVccHighVpi 3.1.637.3.1.4.37.1.2.1.12
The high value of the Virtual Path Identifier (VPI) range dedicated to Virtual Channel (VC) switching on this ATM interface. Common Name: High VPI Value
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxPVpcs 3.1.637.3.1.4.37.1.2.1.13
The maximum number of permanent Virtual Path Connections (VPCs) on this ATM interface. Common Names: Max Permanent VPCs, Max P-VPCs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfacePvpcLowVpi 3.1.637.3.1.4.37.1.2.1.14
The low value of the Virtual Path Identifier (VPI) range dedicated to permanent Virtual Path Connections (VPCs) on this ATM interface. Common Name: Low VPI Value (P-VPCs)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfacePvpcHighVpi 3.1.637.3.1.4.37.1.2.1.15
The high value of the Virtual Path Identifier (VPI) range dedicated to permanent Virtual Path Connections (VPCs) on this ATM interface. Common Name: High VPI Value (P-VPCs)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxSVpcs 3.1.637.3.1.4.37.1.2.1.16
The maximum number of switched Virtual Path Connections (VPCs) on this ATM interface. Common Names: Max Switched VPCs, Max S-VPCs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceSvpcAllocOrd 3.1.637.3.1.4.37.1.2.1.17
The Virtual Path Identifier (VPI) allocation order for switched Virtual Path Connections (VPCs) on this ATM interface. Common Name: VPI Allocation Order (S-VPCs)
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmAllocOrder  

adnAtmInterfaceSvpcLowVpi 3.1.637.3.1.4.37.1.2.1.18
The low value of the Virtual Path Identifier (VPI) range dedicated to switched Virtual Path Connections (VPCs) on this ATM interface. Common Name: Low VPI Value (S-VPCs)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceSvpcHighVpi 3.1.637.3.1.4.37.1.2.1.19
The high value of the Virtual Path Identifier (VPI) range dedicated to switched Virtual Path Connections (VPCs) on this ATM interface. Common Name: High VPI Value (S-VPCs)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxActiveVpVpiBits 3.1.637.3.1.4.37.1.2.1.20
The maximum number of active Virtual Path Identifier (VPI) bits configured for use on this ATM interface, in Virtual Path (VP) switch mode. The not significant value is 0. Common Name: Max VPI Bits for VPCs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxActiveVcVpiBits 3.1.637.3.1.4.37.1.2.1.21
The maximum number of active Virtual Path Identifier (VPI) bits configured for use on this ATM interface, in Virtual Channel (VC) switch mode. The not significant value is 0. Common Name: Max VPI Bits for VCCs
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceCharging 3.1.637.3.1.4.37.1.2.1.22
Whether charging is enabled for all Switched Virtual Connections (SVCs) (switched Virtual Path Connections (VPCs) and Virtual Channel Connections (VCCs)) and the default value for the Permanent Virtual Connections (PVCs) supported by this ATM interface. For the PVCs (VPCs and VCCs) the charging status could be defined per cross-connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmInterfaceStatistics 3.1.637.3.1.4.37.1.2.1.23
Whether statistics are enabled for all Switched Virtual Connections (SVCs) (switched Virtual Path Connections (VPCs) and Virtual Channel Connections (VCCs)) and the default value for the Permanent Virtual Connections (PVCs) supported by this ATM interface. For the PVCs (VPCs and VCCs) the statistics status could be defined per cross-connection. Common Name: Statistics
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmInterfaceTraps 3.1.637.3.1.4.37.1.2.1.24
Whether traps are reported to the NMS for this interface. Traps can be reported at ATM interface level, virtual connection level, Signalling ATM Adaptation Layer (SAAL) level and signalling level. Common Name: Traps
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmInterfaceUserNetFlg 3.1.637.3.1.4.37.1.2.1.25
Whether the interface follows the user or network side of the protocol recommendations. Common Names: User or Network Side, User/Network
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER user(1), network(2), notsignificant(3)  

adnAtmInterfaceSigType 3.1.637.3.1.4.37.1.2.1.26
The type of signalling used for the interface: The following three types are allowed for non Tag Distribution Protocol (TDP) interfaces: - 'nonAssociated': An unique signalling Virtual Channel Connection (VCC) is used to control the Virtual Path Connections (VPCs) and VCCs for the interface - 'associated': Several signalling VCCs used. One controls the interface VPCs. There is also a signalling VCC for each Virtual Path Identifier (VPI) value dedicated to Virtual Channel (VC) switching which controls the VCC having the VPI value - 'noSignalling': No signalling VCC used. The following two types are allowed for TDP interfaces only: - 'ipTdp': An unique signalling VCC is used to control the VCCs for the interface. - 'ipTdpCvsi': In addition to a signalling VCC used to control the VCCs for the interface, there is an extra VCC carrying Cisco Virtual Switch Interface (CVSI) messages between the High Speed System (HSS) and the connected 'tdpAccess' acting as a Tag Switch Controller (TSC). Common Name: Signal Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER nonAssociated(1), associated(2), noSignalling(3), ipTdp(4), ipTdpCvsi(5)  

adnAtmInterfaceRemRoutingNodeID 3.1.637.3.1.4.37.1.2.1.27
The remote node identifier. This is significant only if this is a Cell alcatel Network protocol Interface (CNI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnAtmInterfaceRemIfIndex 3.1.637.3.1.4.37.1.2.1.28
The ifIndex of the remote ATM interface. This is significant only if this is a Cell alcatel Network protocol Interface (CNI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnAtmInterfaceCniBlockingStatus 3.1.637.3.1.4.37.1.2.1.29
The blocking status of the Cell alcatel Network protocol Interface (CNI): - 'available': The CNI can be used to establish new Virtual Path Connections (VPCs) or Virtual Channel Connections (VCCs) - 'blocked': The CNI is not used for establishing new VPCs or VCCs - 'notSignificant': For all ATM interface types except 'physicalCni' and 'routlogicalCni'. Common Name: Blocking Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER available(1), blocked(2), notSignificant(3)  

adnAtmInterfaceMaxVcs 3.1.637.3.1.4.37.1.2.1.30
The maximum number of Virtual Connections (VCs) (Virtual Path Connections (VPCs) and Virtual Channel Connections (VCCs) on this ATM interface. Common Name: Max Virtual Connections
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxPtmRootVcs 3.1.637.3.1.4.37.1.2.1.31
The maximum number of point-to-multipoint root Virtual Connections (VCs) on this ATM interface. Common Name: Max Point-to-Multipoint Root Virtual Connections
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxPtmLeafVcs 3.1.637.3.1.4.37.1.2.1.32
The maximum number of point-to-multipoint leaf Virtual Connections (VCs) on this ATM interface. Common Name: Max Point-to-Multipoint Leaf Virtual Connections
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxVpiForVccs 3.1.637.3.1.4.37.1.2.1.33
The maximum number of Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs) on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceCacAlgorithm 3.1.637.3.1.4.37.1.2.1.34
Whether Connection Admission Control (CAC) algorithm is enabled on this interface. This nominator doesn't have any impact on the CAC algorithm applied on the AEI associated to this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmInterfaceK 3.1.637.3.1.4.37.1.2.1.35
The Connection Admission Control (CAC) overbooking factor, expressed as a percentage, on the ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceKUbr 3.1.637.3.1.4.37.1.2.1.36
The Connection Admission Control (CAC) overbooking factor, expressed as a percentage, for Unspecified Bit Rate (UBR) connections.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnPercent  

adnAtmInterfaceUbr1Tagging 3.1.637.3.1.4.37.1.2.1.37
Whether the switch accepts to treat the Switched Virtual Connections (SVCs) Unspecified Bit Rate (UBR) with no tagging (ubr.1) (specified in the Setup message received) as an UBR connection with tagging (ubr.2). The non significant value is 'disabled'.
Status: deprecated Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmInterfacePolicing 3.1.637.3.1.4.37.1.2.1.38
The status of the policing function applied, in the receiving direction, for all Switched Virtual Connections (SVCs) (switched Virtual Path Connections (VPCs) and Virtual Channel Connections (VCCs)) and the default value for the Permanent Virtual Connections (PVCs) supported by this ATM interface: - 'notPoliced': Police disabled - 'policed': Police enabled - 'supervision': Police disabled, but the police counters are updated. For the PVCs (VPCs and VCCs) the policing function could be defined per cross-connection. Common Name: Policing
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notPoliced(1), policed(3), supervision(4)  

adnAtmInterfaceMonetaryCost 3.1.637.3.1.4.37.1.2.1.39
The monetary cost associated to this ATM interface. This object is significant only if the interface type is a routable Cell alcatel Network protocol Interface (CNI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceTransitDelay 3.1.637.3.1.4.37.1.2.1.40
The transit delay configured for this ATM interface. This object is significant only if the interface type is a routable Cell alcatel Network protocol Interface (CNI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxTDSensitive 3.1.637.3.1.4.37.1.2.1.41
The maximum allowed transit delay for all delay sensitive Switched Virtual Connections (SVCs) (switched Virtual Path Connections (VPCs) and Virtual Channel Connections (VCCs)) and the default value for the Permanent Virtual Connections (PVCs) supported by this ATM interface. The delay sensitivity of a connection is deduced from the ATM Transfer Capability (ATC) of the link, specified by adnAtmVplTransferCapability and adnAtmVclTransferCapability. For the PVCs (VPCs and VCCs) the maximum allowed transit delay could be defined per connection. This object is significant only if the interface type is not a Cell alcatel Network protocol Interface (CNI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceMaxTDOther 3.1.637.3.1.4.37.1.2.1.42
The maximum allowed transit delay for all no delay sensitive Switched Virtual Connections (SVCs) (switched Virtual Path Connections (VPCs) and Virtual Channel Connections (VCCs)) and the default value for the Permanent Virtual Connections (PVCs) supported by this ATM interface. The delay sensitivity of a connection is deduced from the ATM Transfer Capability (ATC) of the link, specified by adnAtmVplTransferCapability and adnAtmVclTransferCapability. For the PVCs (VPCs and VCCs) the maximum allowed transit could be defined per connection. This object is significant only if the interface type is not a Cell alcatel Network protocol Interface (CNI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceChargingBehaviour 3.1.637.3.1.4.37.1.2.1.43
This object indicates the behaviour of the switch when the charging tickets could not be generated for the Virtual Connections (VCs) (Virtual Path Connections (VPCs) and Virtual Channel Connections (VCCs)) supported by this ATM interface: - 'acceptCalls': The new calls are accepted and the established connections are not released - 'refuseCalls': The new calls are refused and the established connections are not released - 'refuseAndReleaseCalls': The new calls are refused and the established connections are released.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), acceptCalls(2), refuseCalls(3), refuseAndReleaseCalls(4)  

adnAtmInterfaceAddrRegistration 3.1.637.3.1.4.37.1.2.1.44
Whether the address registration procedure is enabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmInterfaceSvcCdvTol 3.1.637.3.1.4.37.1.2.1.45
Value of the Cell Delay Variation Tolerance (CDVTOL) for Switched Virtual Connections (SVCs). Value 0 means that the CDVTOL is chosen internally by the switch. Common Names: SVC CDV Tolerance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmInterfaceVpiForVccAllocOrd 3.1.637.3.1.4.37.1.2.1.46
The allocation order for Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmAllocOrder  

adnAtmInterfaceRemNodeMacNum 3.1.637.3.1.4.37.1.2.1.47
The machine number part of adnAtmInterfaceRemRoutingNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmInterfaceRemNodeAreaNum 3.1.637.3.1.4.37.1.2.1.48
The area number part of adnAtmInterfaceRemRoutingNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmInterfaceAllowedAtc 3.1.637.3.1.4.37.1.2.1.49
Allowed ATM Transfer Capabilities (ATC) for a Virtual Path Connection (VPC) or Virtual Channel Connection (VCC) supported by the ATM interface: - 'anyAtc': The ATM interface is able to support any ATC - 'ubr1Only': The ATM interface can only support Unspecified Bit Rate 1 (UBR1) ATC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), anyAtc(2), onlyUbr1(3)  

adnAtmVpiVccConfTable 3.1.637.3.1.4.37.1.3
This table describes the characteristics of the ATM interface's Virtual Path Identifiers (VPIs) dedicated to Virtual Channel Connections (VCCs).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmVpiVccConfEntry

adnAtmVpiVccConfEntry 3.1.637.3.1.4.37.1.3.1
An entry in the adnAtmVpiVccConfTable. There is one entry for each Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs) on an ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmVpiVccConfEntry  

adnAtmVpiVccIndex 3.1.637.3.1.4.37.1.3.1.1
The value of the Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs) on the ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmVpiVccTrmBandwidth 3.1.637.3.1.4.37.1.3.1.2
The bandwidth limitation (if any) of the Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs) in the transmit direction. If both adnAtmVpiVccTrmBandwidth and adnAtmVpiVccRcvBandwidth are set to zero, the bandwidth limitation is the interface bandwidth.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpiVccRcvBandwidth 3.1.637.3.1.4.37.1.3.1.3
The bandwidth limitation (if any) of the Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs) in the receiving direction. If both adnAtmVpiVccRcvBandwidth and adnAtmVpiVccTrmBandwidth are '0', the bandwidth limitation is the interface bandwidth.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpiVccMaxFillingRate 3.1.637.3.1.4.37.1.3.1.4
The bandwidth filling rate of the Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpiVccMaxVcc 3.1.637.3.1.4.37.1.3.1.5
The maximum number of Virtual Channel Connections (VCCs) that can be set up on this Virtual Path Identifier (VPI). Common Name: Max VCCs on VPI
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpiVccMaxPVccs 3.1.637.3.1.4.37.1.3.1.6
The maximum number of permanent Virtual Channel Connections (VCCs) that can be set up on this Virtual Path Identifier (VPI). Common Name: Max P-VCCs on VPI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpiVccPvccLowVci 3.1.637.3.1.4.37.1.3.1.7
The low value of the Virtual Channel Identifier (VCI) range dedicated to permanent Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpiVccPvccHighVci 3.1.637.3.1.4.37.1.3.1.8
The high value of the Virtual Channel Identifier (VCI) range dedicated to permanent Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpiVccMaxSVccs 3.1.637.3.1.4.37.1.3.1.9
The maximum number of switched Virtual Channel Connections (VCCs) that can be set up on this Virtual Path Identifier (VPI). Common Name: Max S-VCCs on VPI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpiVccSvccAllocOrd 3.1.637.3.1.4.37.1.3.1.10
The Virtual Channel Identifier (VCI) allocation order for switched Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmAllocOrder  

adnAtmVpiVccSvccLowVci 3.1.637.3.1.4.37.1.3.1.11
The low value of the Virtual Channel Identifier (VCI) range dedicated to switched Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpiVccSvccHighVci 3.1.637.3.1.4.37.1.3.1.12
The high value of the Virtual Channel Identifier (VCI) range dedicated to switched Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalTable 3.1.637.3.1.4.37.1.4
This table describes the ATM Adaptation Layer (AAL) configuration used in the ATM signalling and routing protocol stacks.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmSaalEntry

adnAtmSaalEntry 3.1.637.3.1.4.37.1.4.1
An entry in the adnAtmSaalTable. There is one entry for each ATM Adaptation Layer (AAL) connection on an ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmSaalEntry  

adnAtmSaalVpi 3.1.637.3.1.4.37.1.4.1.1
The Virtual Path Identifier (VPI) value of the Virtual Channel Connection (VCC) for this Signalling ATM Adaptation Layer (SAAL) connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmSaalVci 3.1.637.3.1.4.37.1.4.1.2
The Virtual Channel Identifier (VCI) value of the Virtual Channel Connection (VCC) for this Signalling ATM Adaptation Layer (SAAL) connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmSaalConnectType 3.1.637.3.1.4.37.1.4.1.3
The type of the ATM Adaptation Layer (AAL) connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), signalling(2), routing(3)  

adnAtmSaalBandwidth 3.1.637.3.1.4.37.1.4.1.4
The bandwidth of the Virtual Channel Connection (VCC) supporting this ATM Adaptation Layer (AAL) connection.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalMaxCC 3.1.637.3.1.4.37.1.4.1.5
The maximum number of times an unacknowledged Connection Control (CC) Protocol Data Unit (PDU) can be resent for this Signalling ATM Adaptation Layer (SAAL) connection. The connection is aborted when this value is exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalMaxPD 3.1.637.3.1.4.37.1.4.1.6
The maximum number of Sequenced Data (SD) Protocol Data Units (PDUs) that can be sent before a polling PDU for this Signalling ATM Adaptation Layer (SAAL) connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalMaxSTAT 3.1.637.3.1.4.37.1.4.1.7
The maximum number of status parameters that can be sent in a STATus (STAT) Protocol Data Unit (PDU) for this Signalling ATM Adaptation Layer (SAAL) connection. The value must be an odd number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalCCTimer 3.1.637.3.1.4.37.1.4.1.8
The length (in milliseconds) of the Connection Control (CC) Protocol Data Unit (PDU) timer for this Signalling ATM Adaptation Layer (SAAL) connection. If this timer expires, the CC PDU is resent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalNoRespTimer 3.1.637.3.1.4.37.1.4.1.9
The time interval (in seconds) between STATtus (STAT) Protocol Data Units (PDUs) received for this Signalling ATM Adaptation Layer (SAAL) connection. If this timer expires, the connection is aborted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalPollTimer 3.1.637.3.1.4.37.1.4.1.10
The time interval (in milliseconds) between transmissions of POLLing (POLL) Protocol Data Units (PDUs) during the data transfer phase for this Signalling ATM Adaptation Layer (SAAL) connection. If this timer expires, a POLL PDU is sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalKeepAliveTimer 3.1.637.3.1.4.37.1.4.1.11
The amount of time (in milliseconds) allocated for waiting for the STATus (STAT) Protocol Data Unit (PDU) solicited by the final POLLing (POLL) PDU when activity ends on this Signalling ATM Adaptation Layer (SAAL) connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalIdleTimer 3.1.637.3.1.4.37.1.4.1.12
The time interval (in seconds) between transmissions of POLLing (POLL) Protocol Data Units (PDUs) when the connection is no longer in the data transfer phase.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalMaxLength 3.1.637.3.1.4.37.1.4.1.13
The maximum data length of the information field in Protocol Data Units (PDUs) for this Signalling ATM Adaptation Layer (SAAL) connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSaalAdminStatus 3.1.637.3.1.4.37.1.4.1.14
The current administrative status of this Signalling ATM Adaptation Layer (SAAL) connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmAdminStatus  

adnAtmSaalOperStatus 3.1.637.3.1.4.37.1.4.1.15
The current operational status of this Signalling ATM Adaptation Layer (SAAL) connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmOperStatus  

adnAtmSigTable 3.1.637.3.1.4.37.1.5
This table describes the signalling entity controlling an ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmSigEntry

adnAtmSigEntry 3.1.637.3.1.4.37.1.5.1
An entry in the adnAtmSigTable. There is one entry for each Virtual Channel Connection (VCC) controlling an ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmSigEntry  

adnAtmSigVpi 3.1.637.3.1.4.37.1.5.1.1
The value of the Virtual Path Identifier (VPI) for the Virtual Channel Connection (VCC) supporting this signalling entity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmSigVci 3.1.637.3.1.4.37.1.5.1.2
The value of the Virtual Channel Identifier (VCI) for the Virtual Channel Connection (VCC) supporting this signalling entity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmSigProtocol 3.1.637.3.1.4.37.1.5.1.3
The signalling protocol type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), q2931(2), atmfv30(3), atmfv31(4), canpv10(5), atmfv40(6), iisp(7), canpv11(8), canpv20(9)  

adnAtmSigT301 3.1.637.3.1.4.37.1.5.1.4
The length (in seconds) of the timer started upon receipt of an Alerting message. This timer is stopped upon receipt of a Connect message. When the timer expires, the connection is released.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT302 3.1.637.3.1.4.37.1.5.1.5
This timer, is not implemented. The length (in seconds) of the timer started upon transmission of a Setup acknowledge message and restarted on the receipt of any Information message not containing a sending complete indication. This timer is stopped upon receipt of any of the following messages: Information message containing a sending complete indication, Alerting, or Connect request message. When the timer expires, a Call proceeding, Alerting or Connect message is sent, as appropriate if sufficient information has been received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT303 3.1.637.3.1.4.37.1.5.1.6
The length (in seconds) of the timer started upon transmission of a Setup message. The timer is stopped upon receipt of any of the following messages: Alerting, Connect, Call Proceeding, or Release Complete. The first time this timer expires, the Setup message is resent. The second time it expires, the connection is cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT304 3.1.637.3.1.4.37.1.5.1.7
This timer is not implemented. The length (in seconds) of the timer started upon receipt of a Setup acknowledge message and restarted when each Information message is sent. This timer is stopped upon receipt of an Alerting, Connect, or Call proceeding message. When the timer expires, the connection is released.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT306 3.1.637.3.1.4.37.1.5.1.8
This timer is not implemented. The length (in seconds) of the timer started upon transmission of a Release message. This timer is stopped upon receipt of a Release complete message. When this timer expires, a Release complete message is sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT308 3.1.637.3.1.4.37.1.5.1.9
The length (in seconds) of the timer started upon transmission of a Release message. The timer is stopped upon receipt of a Release or Release complete message. The first time this timer expires, the Release message is resent. The second time it expires, the connection is considered as cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT309 3.1.637.3.1.4.37.1.5.1.10
The length (in seconds) of the timer started upon receipt of a Signalling ATM Adaptation Layer (SAAL) disconnection indication. The timer is stopped upon receipt of a SAAL reconnection indication. If the timer expires, all connections carried by the faulty SAAL connection are released.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT310 3.1.637.3.1.4.37.1.5.1.11
The length (in seconds) of the timer started upon receipt of a Call proceeding message. The timer is stopped upon receipt of a Connect or Release message. If the timer expires, the connection is released.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT313 3.1.637.3.1.4.37.1.5.1.12
The length (in seconds) of the timer started upon transmission of a Connect message. The timer is stopped upon receipt of a Connect acknowledge message. If the timer expires, the connection is cleared. This timer is only applicable on the user side of the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT316 3.1.637.3.1.4.37.1.5.1.13
The length (in seconds) of the timer started upon transmission of a Restart message. The timer is stopped upon receipt of a Restart Acknowledge message. If the timer expires, the Restart message may be resent several times.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT317 3.1.637.3.1.4.37.1.5.1.14
The length (in seconds) of the timer started upon receipt of a Restart message. The timer is stopped when the internal clearing of called references is completed. If the timer expires, a maintenance message is sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT322 3.1.637.3.1.4.37.1.5.1.15
The length (in seconds) of the timer started upon transmission of a Status enquiry message. The timer is stopped upon receipt of a Status, Release, or Release complete message. If the timer expires, the Status enquiry message may be resent several times.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT398 3.1.637.3.1.4.37.1.5.1.16
The length (in seconds) of the timer started upon transmission of a Drop party message. The timer is stopped upon receipt of a Drop party acknowledge, Add party reject, or Release message. If the timer expires, the connection is considered as cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT399 3.1.637.3.1.4.37.1.5.1.17
The length (in seconds) of the timer started upon transmission of an Add party message. The timer is stopped upon receipt of an Add party acknowledge, Add party reject, or Release message. If the timer expires, the connection is cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT331 3.1.637.3.1.4.37.1.5.1.18
This timer is not implemented. The length (in seconds) of the timer started upon transmission of an Leaf setup request message. The timer is stopped upon receipt of a Setup, Add party, or Leaf setup failure message. The first time this timer expires, the leaf may optionally retransmit the Leaf setup request message. The second time (or the first time if the resent is not chosen) it expires, the connection is cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigT397 3.1.637.3.1.4.37.1.5.1.19
This timer is not implemented. The length (in seconds) of the timer started upon receipt of an Alerting, or Add party alerting message. This timer is stopped upon receipt of an Alerting acknowledge message. When the timer expires, the connection is released.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmSigUserNetFlag 3.1.637.3.1.4.37.1.5.1.20
Whether the interface follows the user or network side of the protocol recommendations. Common Names: User or Network Side, User/Network
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER user(1), network(2)  

adnAtmSigCallProc 3.1.637.3.1.4.37.1.5.1.21
Whether Call proceeding message is to be sent (by the switch) after a Setup message is received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmSigBrSendComp 3.1.637.3.1.4.37.1.5.1.22
Whether broadband sending complete Information Element (IE) is to be sent (by the switch) systematically in the Setup messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmSigSetupScreening 3.1.637.3.1.4.37.1.5.1.23
Whether the calling party number Information Element (IE) of a Setup message is checked according to the administrative address associated with the interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmSigScreening  

adnAtmSigDdi 3.1.637.3.1.4.37.1.5.1.24
Whether Direct Dialing In (DDI) service is allowed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmSigMsn 3.1.637.3.1.4.37.1.5.1.25
Whether Multiple Subscriber Number (MSN) service is allowed. This service is allowed only if adnAtmInterfaceType is 'externalUni'. If the MSN is allowed, the associated addresses are included in adnAtmReachAssocAddrTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmSigSvccReconnect 3.1.637.3.1.4.37.1.5.1.26
Whether reconnection User Network Interface (UNI) is allowed for switched Virtual Channel Connections (VCCs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmSigCallBarring 3.1.637.3.1.4.37.1.5.1.27
The call barring service: - 'no': No call barring - 'incoming': Incoming Setup messages (sent by the switch) are not allowed - 'outgoing': Outgoing Setup messages (received by the switch) are not allowed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), incoming(2), outgoing(3)  

adnAtmSigClip 3.1.637.3.1.4.37.1.5.1.28
The Calling Line Identification Presentation (CLIP) service implementation. Whether the switch is allowed to update the calling party number and subaddress Information Elements (IEs) in each Setup message sent by the switch to the called subscriber: - 'enabledWithoutOverride': The calling party number IE is transmitted (or inserted if it is not present) in the Setup message sent. If the IE is present in the Setup message received, according to the Presentation Indicator (PI) field value, the address field could be modified by the switch - 'enabledWithOverride': The calling party number IE is transmitted (or inserted if it is not present) in the Setup message sent. If the IE is present in the Setup message received, whatever the PI field value the address field is transmitted in the Setup message sent - 'disabled': The calling party number and subaddress IEs are suppressed in the Setup message sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), enabledWithoutOverride(2), enabledWithOverride(3), disabled(4)  

adnAtmSigClir 3.1.637.3.1.4.37.1.5.1.29
The Calling Line Identification Restriction (CLIR) service implementation. Whether the switch is allowed to update the Presentation Indicator (PI) field of the calling party number Information Element (IE) in each Setup message received (issued from the calling subscriber) and forwarded by the switch to the called subscriber.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmSigPIUpdate  

adnAtmSigColp 3.1.637.3.1.4.37.1.5.1.30
The COnnected Line identification Presentation (COLP) service implementation. Whether the switch is allowed to update the connected party number and subaddress Information Elements (IEs) in each Connect message received by the switch (issued from the calling subscriber) and forwarded to the called subscriber. This object is not significant if adnAtmSigProtocol is 'atmfv31' because the connected party number and subaddress IEs do not exist in the ATM FORUM User-Network Interface (UNI) Specification V3.1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), enabledWithoutOverride(2), enabledWithOverride(3), disabled(4)  

adnAtmSigColr 3.1.637.3.1.4.37.1.5.1.31
The COnnected Line identification Restriction (COLR) service implementation. Whether the switch is allowed to update the Presentation Indicator (PI) field of the connected party number Information Element (IE) in each Connect message received (issued from the calling subscriber) and forwarded by the switch to the called subscriber. This object is not significant if adnAtmSigProtocol is 'atmfv31' because the connected party number ans subaddress IEs do not exist in the ATM FORUM User-Network Interface (UNI) Specification V3.1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmSigPIUpdate  

adnAtmSigSub 3.1.637.3.1.4.37.1.5.1.32
Whether SUBaddressing (SUB) service is allowed. Whether the network is allowed to transmit the called subaddress Information Element (IE) in each Setup message forwarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmSigUus 3.1.637.3.1.4.37.1.5.1.33
Whether User User Signalling (UUS) service is allowed. Whether the subscriber is allowed to insert the UUS Information Element (IE) in the Setup message sent. This object is not significant if adnAtmSigProtocol is 'atmfv31' because the UUS IE does not exist in the ATM FORUM User-Network Interface (UNI) Specification V3.1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmSigVpiVciAlloc 3.1.637.3.1.4.37.1.5.1.34
Whether the VPi and VCi number are inserted in the Setup request message. This object is significant only when the switch follows the network side of the protocol recommendations. This object is significant only if adnAtmSigProtocol is 'atmfv40'. The not significant value is 'disabled'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmSigCniCheckingState 3.1.637.3.1.4.37.1.5.1.35
The current status of the validity checking phase which is performed when setting an ATM trunk into service. This read-only nominator is significant only if the associated ATM interface is a trunk. Common Name: CNI validity checking
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(1), ok(2), nokUserNet(3), nokCanp(4), nokSaal(5), nokConf(6), notYetPerformed(65535)  

adnAtmSigSetupAddr 3.1.637.3.1.4.37.1.5.1.36
This nominator defines which addressing Information Element (IE) is used by the switch to forward a Setup received. - 'calledPartyNumber': The called party number is used to forward the call, this is the normal case - 'calledPartySubAddress': The called party subaddress is used to forward the call as defined in E191 standard. In this case, the switch replaces the called party number received by the called party subaddress and forwards the call with it. If no called party subaddress is received, the call is rejected - 'both': Depending on the content of the Setup received, the call is forwarded either with the: . called party subaddress (if present in the Setup received) . called party number if the call party subaddress is not present in the Setup received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(1), calledPartyNumber(2), calledPartySubAddress(3), both(4)  

adnAtmSigConnectScreening 3.1.637.3.1.4.37.1.5.1.37
Whether the called party number Information Element (IE) of a Connect message is checked according to the administrative address associated with the interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmSigScreening  

adnAtmVplTable 3.1.637.3.1.4.37.1.6
This is an extension of the Virtual Path (VP) link table, described in RFC 1695.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmVplEntry

adnAtmVplEntry 3.1.637.3.1.4.37.1.6.1
An entry in the extension to the Virtual Path (VP) link table. There is one entry for each VP link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmVplEntry  

adnAtmVplTopology 3.1.637.3.1.4.37.1.6.1.1
The topology type of this Virtual Path Link (VPL). Common Name: Topology
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pointToPoint(1), pointToMultipoint(2), pointToMultipointRoot(3), pointToMultipointLeaf(4)  

adnAtmVplTrafficType 3.1.637.3.1.4.37.1.6.1.2
The type of traffic carried on this Virtual Path Link (VPL). Common Name: Traffic Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER userTraffic(1), networkTraffic(2)  

adnAtmVplType 3.1.637.3.1.4.37.1.6.1.3
The type of this Virtual Path Link (VPL). Common Name: VPL Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlType  

adnAtmVplTransferCapability 3.1.637.3.1.4.37.1.6.1.4
The ATM Transfer Capabilities (ATC) offered on this Virtual Path Link (VPL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlTrfCapability  

adnAtmVplTrafficDescrType 3.1.637.3.1.4.37.1.6.1.5
The type of Virtual Path Link (VPL) traffic descriptor in the transmit and receiving direction. Depending on the value, certain traffic parameters must be initialized: - 'adnAtmTrafficDescPcrCdv': The following traffic parameters must be initialized: adnAtmVplTrmPcrAggregate, adnAtmVplRcvPcrAggregate, adnAtmVplTrmCdvTol, adnAtmVplRcvCdvTol, adnAtmVplTrmBwWeighting, adnAtmVplRcvBwWeighting, - 'adnAtmTrafficDescPcrCdvScrMbs': The following traffic parameters must be initialized: adnAtmVplTrmPcrAggregate, adnAtmVplRcvPcrAggregate, adnAtmVplTrmScrAggregate, adnAtmVplRcvScrAggregate, adnAtmVplTrmMbsAggregate, adnAtmVplRcvMbsAggregate, adnAtmVplTrmCdvTol, adnAtmVplRcvCdvTol, adnAtmVplTrmBwWeighting, adnAtmVplRcvBwWeighting.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER adnAtmTrafficDescPcrCdv(1), adnAtmTrafficDescPcrCdvScrMbs(2)  

adnAtmVplTrmPcrAggregate 3.1.637.3.1.4.37.1.6.1.6
The Peak Cell Rate (PCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the transmit direction (switch point of view), of this Virtual Path Link (VPL). Common Names: Transmit Peak Cell Rate (PCR) Aggregate, Transmit PCR Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplTrmPcrClpZero 3.1.637.3.1.4.37.1.6.1.7
The Peak Cell Rate (PCR) for the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, of this Virtual Path Link (VPL). Common Names: Transmit Peak Cell Rate (PCR) Cell Loss Priority (CLP) 0, Transmit PCR CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplTrmScrAggregate 3.1.637.3.1.4.37.1.6.1.8
The Sustainable Cell Rate (SCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the transmit direction, of this Virtual Path Link (VPL). Common Names: Transmit Sustainable Cell Rate (SCR) Aggregate, Transmit SCR Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplTrmScrClpZero 3.1.637.3.1.4.37.1.6.1.9
The Sustainable Cell Rate (SCR) for the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, of this Virtual Path Link (VPL). Common Names: Transmit Sustainable Cell Rate (SCR) Cell Loss Priority (CLP) 0, Transmit SCR CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplTrmMbsAggregate 3.1.637.3.1.4.37.1.6.1.10
The Maximum Burst Size (MBS) for the aggregate traffic (Cell Loss Priority (CLP) 0+1,) in the transmit direction, of this Virtual Path Link (VPL). Common Names: Transmit Maximum Burst Size (MBS) Aggregate, Transmit MBS Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplTrmMbsClpZero 3.1.637.3.1.4.37.1.6.1.11
The Maximum Burst Size (MBS) for the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, of this Virtual Path Link (VPL). Common Names: Transmit Maximum Burst Size (MBS) Cell Loss Priority (CLP) 0, Transmit MBS CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplTrmCdvTol 3.1.637.3.1.4.37.1.6.1.12
The Cell Delay Variation (CDV) tolerance of the traffic, in the transmit direction, of this Virtual Path Link (VPL). Common Names: Transmit Cell Delay Variation (CDV) Tolerance, Transmit CDV Tolerance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplTrmBwWeighting 3.1.637.3.1.4.37.1.6.1.13
The weight applied to the allocated bandwidth, expressed as a percentage, in the transmit direction. Common Name: Transmit Bandwidth Weighting
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplRcvPcrAggregate 3.1.637.3.1.4.37.1.6.1.14
The Peak Cell Rate (PCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the receiving direction, of this Virtual Path Link (VPL). Common Names: Receive Peak Cell Rate (PCR) Aggregate, Receive PCR Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplRcvPcrClpZero 3.1.637.3.1.4.37.1.6.1.15
The Peak Cell Rate (PCR) for the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, of this Virtual Path Link (VPL). Common Names: Receive Peak Cell Rate (PCR) Cell Loss Priority (CLP) 0, Receive PCR CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplRcvScrAggregate 3.1.637.3.1.4.37.1.6.1.16
The Sustainable Cell Rate (SCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the receiving direction, of this Virtual Path Link (VPL). Common Names: Receive Sustainable Cell Rate (SCR) Aggregate, Receive SCR Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplRcvScrClpZero 3.1.637.3.1.4.37.1.6.1.17
The Sustainable Cell Rate (SCR) for the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, of this Virtual Path Link (VPL). Common Names: Receive Sustainable Cell Rate (SCR) Cell Loss Priority (CLP) 0, Receive SCR CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplRcvMbsAggregate 3.1.637.3.1.4.37.1.6.1.18
The Maximum Burst Size (MBS) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the receiving direction, of this Virtual Path Link (VPL). Common Names: Receive Maximum Burst Size (MBS) Aggregate, Receive MBS Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplRcvMbsClpZero 3.1.637.3.1.4.37.1.6.1.19
The Maximum Burst Size (MBS) for the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, of this Virtual Path Link (VPL). Common Names: Receive Maximum Burst Size (MBS) Cell Loss Priority (CLP) 0, Receive MBS CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplRcvCdvTol 3.1.637.3.1.4.37.1.6.1.20
The Cell Delay Variation (CDV) tolerance of the traffic, in the receiving direction, of this Virtual Path Link (VPL). Common Names: Receive Cell Delay Variation (CDV) Tolerance, Receive CDV Tolerance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplRcvBwWeighting 3.1.637.3.1.4.37.1.6.1.21
The weight applied to the allocated bandwidth, expressed as a percentage, in the receiving direction. Common Name: Receive Bandwidth Weighting
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVplPolicing 3.1.637.3.1.4.37.1.6.1.22
The status of the policing function applied, in the receiving direction, of this Virtual Path Link (VPL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlPolicing  

adnAtmVplPriority 3.1.637.3.1.4.37.1.6.1.23
The Virtual Path Link (VPL) priority level. Common Name: Priority
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER high(1), low(2)  

adnAtmVplModeType 3.1.637.3.1.4.37.1.6.1.24
Whether this permanent Virtual Path Link (VPL) was created automatically by ATM signalling or manually by an operator. Always 'notsignificant' for Switched Virtual Connections (SVC) and InternalVc. Common Name: Creation Mode
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER automatic(1), manual(2), notsignificant(3)  

adnAtmVplTrmAISStatus 3.1.637.3.1.4.37.1.6.1.25
The Alarm Indication Signal (AIS) end-to-end state, in the transmit direction, of this permanent Virtual Path Link (VPL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlAISStatus  

adnAtmVplTrmTrafficDescrType 3.1.637.3.1.4.37.1.6.1.26
The type of Virtual Path Link (VPL) traffic descriptor in the transmit direction.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlTrfDescrType  

adnAtmVplTrmTagging 3.1.637.3.1.4.37.1.6.1.27
Whether tagging option is enabled on the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, when cells are not conformant, of this Virtual Path Link (VPL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmVplTrmPacketDiscard 3.1.637.3.1.4.37.1.6.1.28
Whether packet discard option is enabled, in the transmit direction, of this Virtual Path Link (VPL). When this option is enabled all the low priority cells in the remaining of an ATM Adaptation Layer (AAL) 5 frame are discarded, as soon as one of the cell of the frame has been discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmVplRcvAISStatus 3.1.637.3.1.4.37.1.6.1.29
The Alarm Indication Signal (AIS) end-to-end state, in the receiving direction, of this permanent Virtual Path Link (VPL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlAISStatus  

adnAtmVplRcvTrafficDescrType 3.1.637.3.1.4.37.1.6.1.30
The type of Virtual Path Link (VPL) traffic descriptor in the receiving direction.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlTrfDescrType  

adnAtmVplRcvTagging 3.1.637.3.1.4.37.1.6.1.31
Whether tagging option is enabled on the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, when cells are not conformant, of this Virtual Path Link (VPL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmVplRcvPacketDiscard 3.1.637.3.1.4.37.1.6.1.32
Whether packet discard option is enabled, in the receiving direction, of this Virtual Path Link (VPL). When this option is enabled all the low priority cells in the remaining of an ATM Adaptation Layer (AAL) 5 frame are discarded, as soon as one of the cell of the frame has been discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmVplInternodeType 3.1.637.3.1.4.37.1.6.1.33
Whether this Virtual Path Link (VPL) is associated with an internode Virtual Path (VP) connection or not. If it is associated, indicates which traffic type can be supported for Virtual Channel Conections (VCCs) part of the internode VP. - 'notSignificant': VPL is not associated with an internode VP - 'rt': Real time traffic types - 'nrtAggregate': Non-real time traffic types with Quality Of Service (QOS) committment on aggregate traffic (Cell Loss Priority (CLP) 0+1) - 'nrtZero': Non-real time traffic types with QOS committment on CLP 0 traffic - 'u': Unspecified bit rate traffic types - 'anyAtc': Any traffic types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(1), rt(2), nrtAggregate(3), nrtZero(4), u(5), anyAtc(6)  

adnAtmVclTable 3.1.637.3.1.4.37.1.7
This is an extension of the VC Link table, described in RFC 1695.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmVclEntry

adnAtmVclEntry 3.1.637.3.1.4.37.1.7.1
An entry in the VC Link extension table. There is one entry for each VC link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmVclEntry  

adnAtmVclTopology 3.1.637.3.1.4.37.1.7.1.1
The topology type of this Virtual Channel Link (VCL). Common Name: Topology
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pointToPoint(1), pointToMultipoint(2), pointToMultipointRoot(3), pointToMultipointLeaf(4)  

adnAtmVclTrafficType 3.1.637.3.1.4.37.1.7.1.2
The type of traffic carried on this Virtual Channel Link (VCL). Common Name: Traffic Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER userTraffic(1), networkTraffic(2)  

adnAtmVclType 3.1.637.3.1.4.37.1.7.1.3
The type of this Virtual Channel Link (VCL). Common Name: VCL Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlType  

adnAtmVclTransferCapability 3.1.637.3.1.4.37.1.7.1.4
The ATM Transfer Capabilities (ATC) offered on this Virtual Channel Link (VCL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlTrfCapability  

adnAtmVclTrafficDescrType 3.1.637.3.1.4.37.1.7.1.5
The type of Virtual Channel Link (VCL) traffic descriptor in the transmit and receiving direction. Depending on the value, certain traffic parameters must be initialized: - 'adnAtmTrafficDescPcrCdv': The following traffic parameters must be initialized: adnAtmVclTrmPcrAggregate, adnAtmVclRcvPcrAggregate, adnAtmVclTrmCdvTol, adnAtmVclRcvCdvTol, adnAtmVclTrmBwWeighting, adnAtmVclRcvBwWeighting, - 'adnAtmTrafficDescPcrCdvScrMbs': The following traffic parameters must be initialized: adnAtmVclTrmPcrAggregate, adnAtmVclRcvPcrAggregate, adnAtmVclTrmScrAggregate, adnAtmVclRcvScrAggregate, adnAtmVclTrmMbsAggregate, adnAtmVclRcvMbsAggregate, adnAtmVclTrmCdvTol, adnAtmVclRcvCdvTol, adnAtmVclTrmBwWeighting, adnAtmVclRcvBwWeighting. Common Name: Traffic Descriptor
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER adnAtmTrafficDescPcrCdv(1), adnAtmTrafficDescPcrCdvScrMbs(2)  

adnAtmVclTrmPcrAggregate 3.1.637.3.1.4.37.1.7.1.6
The Peak Cell Rate (PCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the transmit direction (switch point of view), of this Virtual Channel Link (VCL). Common Names: Transmit Peak Cell Rate (PCR) Aggregate, Transmit PCR Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclTrmPcrClpZero 3.1.637.3.1.4.37.1.7.1.7
The Peak Cell Rate (PCR) for the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Peak Cell Rate (PCR) Cell Loss Priority (CLP) 0, Transmit PCR CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclTrmScrAggregate 3.1.637.3.1.4.37.1.7.1.8
The Sustainable Cell Rate (SCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Sustainable Cell Rate (SCR) Aggregate, Transmit SCR Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclTrmScrClpZero 3.1.637.3.1.4.37.1.7.1.9
The Sustainable Cell Rate (SCR) for the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Sustainable Cell Rate (SCR) Cell Loss Priority (CLP) 0, Transmit SCR CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclTrmMbsAggregate 3.1.637.3.1.4.37.1.7.1.10
The Maximum Burst Size (MBS) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Maximum Burst Size (MBS) Aggregate, Transmit MBS Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclTrmMbsClpZero 3.1.637.3.1.4.37.1.7.1.11
The Maximum Burst Size (MBS) for the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Maximum Burst Size (MBS) Cell Loss Priority (CLP) 0, Transmit MBS CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclTrmCdvTol 3.1.637.3.1.4.37.1.7.1.12
The Cell Delay Variation (CDV) tolerance of the traffic, in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Cell Delay Variation (CDV) Tolerance, Transmit CDV Tolerance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclTrmBwWeighting 3.1.637.3.1.4.37.1.7.1.13
The weight applied to the allocated bandwidth, expressed as a percentage, in the transmit direction. Common Name: Transmit Bandwidth Weighting
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclRcvPcrAggregate 3.1.637.3.1.4.37.1.7.1.14
The Peak Cell Rate (PCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Peak Cell Rate (PCR) Aggregate, Receive PCR Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclRcvPcrClpZero 3.1.637.3.1.4.37.1.7.1.15
The Peak Cell Rate (PCR) for the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Peak Cell Rate (PCR) Cell Loss Priority (CLP) 0, Receive PCR CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclRcvScrAggregate 3.1.637.3.1.4.37.1.7.1.16
The Sustainable Cell Rate (SCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Sustainable Cell Rate (SCR) Aggregate, Receive SCR Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclRcvScrClpZero 3.1.637.3.1.4.37.1.7.1.17
The Sustainable Cell Rate (SCR) for the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Sustainable Cell Rate (SCR) Cell Loss Priority (CLP) 0, Receive SCR CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclRcvMbsAggregate 3.1.637.3.1.4.37.1.7.1.18
The Maximum Burst Size (MBS) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Maximum Burst Size (MBS) Aggregate, Receive MBS Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclRcvMbsClpZero 3.1.637.3.1.4.37.1.7.1.19
The Maximum Burst Size (MBS) for the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Maximum Burst Size (MBS) Cell Priority (CLP) 0, Receive MBS CLP 0
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclRcvCdvTol 3.1.637.3.1.4.37.1.7.1.20
The Cell Delay Variation (CDV) tolerance of the traffic, in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Cell Delay Variation (CDV) Tolerance, Receive CDV Tolerance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclRcvBwWeighting 3.1.637.3.1.4.37.1.7.1.21
The weight applied to the allocated bandwidth, expressed as a percentage, in the receiving direction. Common Name: Receive Bandwidth Weighting
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVclPolicing 3.1.637.3.1.4.37.1.7.1.22
The status of the policing function applied, in the receiving direction, of this Virtual Channel Link (VCL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlPolicing  

adnAtmVclPriority 3.1.637.3.1.4.37.1.7.1.23
The Virtual Channel Link (VCL) priority level. Common Name: Priority
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER high(1), low(2)  

adnAtmVclModeType 3.1.637.3.1.4.37.1.7.1.24
Whether this permanent Virtual Channel Link (VCL) was created automatically by ATM signalling or manually by an operator. Always 'notSignificant' for Switched Virtual Connections (SVC) and InternalVc. Common Name: Creation Mode
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER automatic(1), manual(2), notSignificant(3)  

adnAtmVclTrmAISStatus 3.1.637.3.1.4.37.1.7.1.25
The Alarm Indication Signal (AIS) end-to-end state, in the transmit direction, of this permanent Virtual Channel Link (VCL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlAISStatus  

adnAtmVclTrmTrafficDescrType 3.1.637.3.1.4.37.1.7.1.26
The type of Virtual Channel Link (VCL) traffic descriptor in the transmit direction.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlTrfDescrType  

adnAtmVclTrmTagging 3.1.637.3.1.4.37.1.7.1.27
Whether tagging option is enabled on the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, when cells are not conformant, of this Virtual Channel Link (VCL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmVclTrmPacketDiscard 3.1.637.3.1.4.37.1.7.1.28
Whether packet discard option is enabled, in the transmit direction, of this Virtual Channel Link (VCL). When this option is enabled all the low priority cells in the remaining of an ATM Adaptation Layer (AAL) 5 frame are discarded, as soon as one of the cell of the frame has been discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmVclRcvAISStatus 3.1.637.3.1.4.37.1.7.1.29
The Alarm Indication Signal (AIS) end-to-end state, in the receiving direction, of this permanent Virtual Channel Link (VCL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlAISStatus  

adnAtmVclRcvTrafficDescrType 3.1.637.3.1.4.37.1.7.1.30
The type of Virtual Channel Link (VCL) traffic descriptor in the receiving direction.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmVlTrfDescrType  

adnAtmVclRcvTagging 3.1.637.3.1.4.37.1.7.1.31
Whether tagging option is enabled on the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, when cells are not conformant, of this Virtual Channel Link (VCL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmVclRcvPacketDiscard 3.1.637.3.1.4.37.1.7.1.32
Whether packet discard option is enabled, in the receiving direction, of this Virtual Channel Link (VCL). When this option is enabled all the low priority cells in the remaining of an ATM Adaptation Layer (AAL) 5 frame are discarded, as soon as one of the cell of the frame has been discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnEnableDisabled  

adnAtmVclLogLineType 3.1.637.3.1.4.37.1.7.1.33
The type of service using the frame relay logical line: - franpOverAtm: FRANP truncking over ATM - netIWsc2OneToOne: Network interworking scenario 2 with each Fame Relay (FR) connection mapped to a single ATM Virtual Channel Connection (VCC) - netIWsc2ManyToOne: Network interworking scenario 2 with multiple FR connections multiplexed into a single ATM VCC - netIWsc1: Network interworking scenario 1 - serIW: Service interworking - issc: NMS-ISS connection over ATM. Common Name: Logical Line Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), franpOverAtm(2), netIWsc2OneToOne(3), netIWsc2ManyToOne(4), netIWsc1(5), serIW(6), issc(7), notSignificant(8)  

adnAtmUniVpCconnectTable 3.1.637.3.1.4.37.1.8
The ATM User Network Interface (UNI) Virtual Path cross-connect table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmUniVpCconnectEntry

adnAtmUniVpCconnectEntry 3.1.637.3.1.4.37.1.8.1
An entry in the User Network Interface (UNI) Virtual Path cross-connect table. There is one entry for each User Network Interface/Network Network Interface (UNI/NNI) Virtual Path (VP) cross-connection. An entry describes both the local cross-connection and the end-to-end cross-connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmUniVpCconnectEntry  

adnAtmUniVpCconnectIndex 3.1.637.3.1.4.37.1.8.1.1
The index of the cross-connection for the Virtual Path Connection (VPC) on this interface. The index is 0 for a point-to-point cross-connection. There is a different index for each leaf in a point-to-multipoint cross-connection. Common Name: Cross-connection Index
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectOutIfIndex 3.1.637.3.1.4.37.1.8.1.2
The ifIndex of the output ATM interface from this node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnAtmUniVpCconnectOutVpi 3.1.637.3.1.4.37.1.8.1.3
The Virtual Path Identifier (VPI) of this connection on the output ATM interface from this node. In conjunction with adnAtmUniVpCconnectOutIfIndex, this VPI can be used for path tracing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectOutCcnIndex 3.1.637.3.1.4.37.1.8.1.4
The cross-connection index of this output Virtual Path Identifier (VPI) of the output ATM interface from this node. This can be combined with adnAtmUniVpCconnectOutIfIndex and adnAtmUniVpCconnectOutVpi and used for call tracing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectAdminStatus 3.1.637.3.1.4.37.1.8.1.5
The current administrative status of this Virtual Path (VP) cross-connection. The 'up' and 'down' states indicate whether or not this ATM VP cross-connection is operational.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnAtmAdminStatus  

adnAtmUniVpCconnectOperStatus 3.1.637.3.1.4.37.1.8.1.6
The current Virtual Path Connection (VPC) call attempt state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmUniOperStatus  

adnAtmUniVpCconnectSourceDest 3.1.637.3.1.4.37.1.8.1.7
Whether this is the source or destination side of the virtual cross-connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmUniSourceDest  

adnAtmUniVpCconnectStatistics 3.1.637.3.1.4.37.1.8.1.8
Whether statistics are enabled for this Virtual Path (VP) cross-connection. This object is significant only if the type of the Virtual Path Link (VPL), specified by adnAtmVplType, is set to 'pvc'; otherwise, the statistics status is defined per interface. If set to 'useInterfaceValue', the value defined per interface is used. Common Name: Statistics
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), useInterfaceValue(3)  

adnAtmUniVpCconnectDirectedPath 3.1.637.3.1.4.37.1.8.1.9
Whether this Virtual Path Connection (VPC) uses a directed path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnAtmDirectedPath  

adnAtmUniVpCconnectRetryAttempts 3.1.637.3.1.4.37.1.8.1.10
The number of call attempts to make at the fast rate (adnAtmUniVpCconnectFastRetry) before slowing the call attempt rate to adnAtmUniVpCconnectSlowRetry. The current attempt state is in adnAtmUniVpCconnectOperStatus. This object is significant only if adnAtmUniVpCconnectSourceDest is 'source', adnAtmVplType is 'pvc' and adnAtmVplModeType is 'automatic'. Common Name: Retry Attempts at Fast Rate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectFastRetry 3.1.637.3.1.4.37.1.8.1.11
This timer specifies the amount of time to wait between failed Permanent Virtual Connection (PVC) setup attempts at the fast rate. After attempting setups at this rate for adnAtmUniVpCconnectCRetryAttempts times, the rate slows to the adnAtmUniVpCconnectSlowRetry rate. This object is significant only if adnAtmUniVpCconnectSourceDest is 'source', adnAtmVplType is 'pvc', and adnAtmVplModeType is 'automatic'. Common Name: Wait Time between Fast Retries
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectSlowRetry 3.1.637.3.1.4.37.1.8.1.12
This timer specifies the amount of time to wait between failed Permanent Virtual Connection (PVC) setup attempts at the slow rate. After attempting setups at the adnAtmUniVpCconnectFastRetry rate for adnAtmUniVpCconnectRetryAttempts times, the rate slows to the adnAtmUniVpCconnectSlowRetry rate. This is significant only if adnAtmUniVpCconnectSourceDest is 'source', adnAtmVplType is 'pvc', and adnAtmVplModeType is 'automatic'. Common Name: Wait Time between Slow Retries
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectRemNumPlan 3.1.637.3.1.4.37.1.8.1.13
The numbering plan of the remote User Network Interface (UNI) for the current Virtual Path (VP) cross-connection. Common Names: Remote Numbering Plan, Rem Num Plan
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmNumPlan  

adnAtmUniVpCconnectRemPhysAddress 3.1.637.3.1.4.37.1.8.1.14
The address of the remote User Network Interface/Network Network Interface (UNI/NNI) for the current Virtual Path (VP) cross-connection. Common Name: Remote Address
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

adnAtmUniVpCconnectRemVpi 3.1.637.3.1.4.37.1.8.1.15
The Virtual Path Identifier (VPI) of the remote User Network Interface/Network Network Interface (UNI/NNI) for the current Virtual Path (VP) cross-connection. Common Name: Remote VPI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectRemCcnIndex 3.1.637.3.1.4.37.1.8.1.16
The value of the remote User Network Interface/Network Network Interface (UNI/NNI) cross-connection for the current Virtual Path (VP) cross-connection. Common Name: Remote Cross-connection Index
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectRemRoutingNodeId 3.1.637.3.1.4.37.1.8.1.17
The identifier of the node connecting the remote User Network Interface/Network Network Interface (UNI/NNI) for the current Virtual Path (VP) cross-connection. Common Name: Remote Node Identifier
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnAtmUniVpCconnectCumulNodes 3.1.637.3.1.4.37.1.8.1.18
The number of nodes in the connection. If adnAtmUniVpCconnectOperStatus is 'callup', this is the current nodes count; otherwise, it is the nodes count for the last connection. Common Name: Number of Nodes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectMaxTransitDelay 3.1.637.3.1.4.37.1.8.1.19
The maximum allowed transit delay of this Virtual Path (VP) cross-connection. This object is significant only if the type of the Virtual Path Link (VPL), specified by adnAtmVplType, is set to 'pvc'. In case of 'svc', the maximum transit delay is defined per interface or could be defined in an Information Element If set to 0, the value defined per interface is used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectCharging 3.1.637.3.1.4.37.1.8.1.20
Whether charging is enabled for this Virtual Path (VP) cross-connection. This object is significant only if the type of the Virtual Path Link (VPL), specified by adnAtmVplType, is set to 'pvc'; otherwise, the charging status is defined per interface. If set to 'useInterfaceValue', the value defined per interface is used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), enabled(2), disabled(3), useInterfaceValue(4)  

adnAtmUniVpCconnectCumulTD 3.1.637.3.1.4.37.1.8.1.21
The current cumulative transit delay of this Virtual Path (VP) cross-connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectCumulMonetaryCst 3.1.637.3.1.4.37.1.8.1.22
The current cumulative monetary cost of this Virtual Path (VP) cross-connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectCauseError 3.1.637.3.1.4.37.1.8.1.23
Global cause of the cross-connect failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(1), maxCallAttempts(2), configurationError(3)  

adnAtmUniVpCconnectLastCanpCause 3.1.637.3.1.4.37.1.8.1.24
Last Cell Alcatel Network Protocol (CANP) cause. This nominator, which is read only, is not significant if adnAtmUniVpCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVpCconnectLastErrorNodeID 3.1.637.3.1.4.37.1.8.1.25
The identifier of the node detecting the error. This nominator, which is read only, is not significant if adnAtmUniVpCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnAtmUniVpCconnectLastLocation 3.1.637.3.1.4.37.1.8.1.26
ATM forum location value in the cause information element. This nominator, which is read only, is not significant if adnAtmUniVpCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVpCconnectLastCause 3.1.637.3.1.4.37.1.8.1.27
ATM forum cause value in the cause information element. This nominator, which is read only, is not significant if adnAtmUniVpCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVpCconnectLastDiag 3.1.637.3.1.4.37.1.8.1.28
ATM forum diagnostic value in the cause information element. This nominator, which is read only, is not significant if adnAtmUniVpCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVpCconnectRemNodeMacNum 3.1.637.3.1.4.37.1.8.1.29
The machine number part of adnAtmUniVpCconnectRemRoutingNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVpCconnectRemNodeAreaNum 3.1.637.3.1.4.37.1.8.1.30
The area number part of adnAtmUniVpCconnectRemRoutingNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVpCconnectErrorNodeMacNum 3.1.637.3.1.4.37.1.8.1.31
The machine number part of adnAtmUniVpCconnectLastErrorNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVpCconnectErrorNodeAreaNum 3.1.637.3.1.4.37.1.8.1.32
The area number part of adnAtmUniVpCconnectLastErrorNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVpCconnectLastChassis 3.1.637.3.1.4.37.1.8.1.33
The chassis number detecting the error. This nominator, which is read only, is not significant if adnAtmUniVpCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVpCconnectLastSlot 3.1.637.3.1.4.37.1.8.1.34
The slot number of the board detecting the error. This nominator, which is read only, is not significant if adnAtmUniVpCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVpCconnectMaxHops 3.1.637.3.1.4.37.1.8.1.35
The maximum allowed number of hops of this Virtual Path (VP) cross-connection. If set to 65535, the value defined at node level is used. Common Name: Number of hops
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVpCconnectPvcDescr 3.1.637.3.1.4.37.1.8.1.36
This object contains the Permanent Virtual Connection (PVC) description inserted in each charging ticket generated for this Virtual Path (VP) cross-connection. This object is significant only if the type of the Virtual Path Link (VPL), specified by adnAtmVplType, is set to 'pvc'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnAtmCniVpCconnectTable 3.1.637.3.1.4.37.1.9
The Virtual Path (VP) cross-connect table on the inter-node ATM interfaces (Cell alcatel Network protocol Interfaces (CNIs)).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmCniVpCconnectEntry

adnAtmCniVpCconnectEntry 3.1.637.3.1.4.37.1.9.1
An entry in the Cell alcatel Network protocol Interface (CNI) Virtual Path (VP) cross-connect table. There is one entry for each VP cross-connection on a CNI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmCniVpCconnectEntry  

adnAtmCniVpCconnectIndex 3.1.637.3.1.4.37.1.9.1.1
The index of the cross-connection for the Virtual Path Connection (VPC) on this interface. In a point-to-point cross-connection, the index equals 0.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmCniVpCconnectOutIfIndex 3.1.637.3.1.4.37.1.9.1.2
The ifIndex of this node's output ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnAtmCniVpCconnectOutVpi 3.1.637.3.1.4.37.1.9.1.3
The Virtual Path Identifier (VPI) of this connection on the output ATM interface from this node. In conjunction with adnAtmCniVpCconnectOutIfIndex, this can be used for path tracing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmCniVpCconnectOutCcnIndex 3.1.637.3.1.4.37.1.9.1.4
The cross-connection index of the output Virtual Path Identifier (VPI) of this node's output ATM interface. This index can be used with adnAtmCniVpCconnectOutIfIndex and adnAtmCniVpCconnectOutVpi for call tracing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmCniVpCconnectAdminStatus 3.1.637.3.1.4.37.1.9.1.5
The current administrative status of this Virtual Path (VP) cross-connection. The 'up' and 'down' states indicate whether or not this ATM VP cross-connection is operational.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmAdminStatus  

adnAtmCniVpCconnectOperStatus 3.1.637.3.1.4.37.1.9.1.6
The current Virtual Path Connection (VPC) call attempt state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmCniOperStatus  

adnAtmCniVpCconnectSourceDest 3.1.637.3.1.4.37.1.9.1.7
Whether this is the source or destination side of the cross-connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmCniSourceDest  

adnAtmCniVpCconnectStatistics 3.1.637.3.1.4.37.1.9.1.8
Whether statistics are enabled for this Virtual Path (VP) cross-connection. This object is significant only if the type of the Virtual Path Link (VPL), specified by adnAtmVplType, is set to 'pvc'; otherwise, the statistics status is defined per interface. If set to 'useInterfaceValue', the value defined per interface is used. Common Name: Statistics
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), useInterfaceValue(3)  

adnAtmCniVpCconnectDirectedPath 3.1.637.3.1.4.37.1.9.1.9
Whether this Virtual Path Connection (VPC) uses a directed path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmDirectedPath  

adnAtmUniVcCconnectTable 3.1.637.3.1.4.37.1.10
The ATM User Network Interface (UNI) Virtual Channel cross-connect table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmUniVcCconnectEntry

adnAtmUniVcCconnectEntry 3.1.637.3.1.4.37.1.10.1
An entry in the ATM User Network Interface (UNI) Virtual Channel (VC) cross-connect table. There is one entry for each UNI VC cross-connection. An entry describes both the local cross-connection and the end-to-end cross-connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmUniVcCconnectEntry  

adnAtmUniVcCconnectIndex 3.1.637.3.1.4.37.1.10.1.1
The index of the cross-connection for the Virtual Channel Connection (VCC) on this interface. In a point-to-point cross-connection, the index equals zero. In a point-to- -multipoint cross-connection, there is a different index for each leaf. Common Name: Cross-connection Index
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectOutIfIndex 3.1.637.3.1.4.37.1.10.1.2
The ifIndex of this node's output ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnAtmUniVcCconnectOutVpi 3.1.637.3.1.4.37.1.10.1.3
The Virtual Path Identifier (VPI) of this connection on the output ATM interface from this node. In conjunction with adnAtmUniVcCconnectOutIfIndex, this VPI can be used for path tracing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectOutVci 3.1.637.3.1.4.37.1.10.1.4
The Virtual Channel Identifier (VCI) of this node's output interface. This cross-connection exits the node on another VCI. This value can be combined with adnAtmUniVcCconnectOutIfIndex and adnAtmUniVcCconnectOutVpi and used for call tracing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectOutCcnIndex 3.1.637.3.1.4.37.1.10.1.5
The cross-connection index of the output Virtual Path Identifier/Virtual Channel Identifier (VPI/VCI) of this node's output interface. This value can be combined with adnAtmUniVcCconnectOutIfIndex, adnAtmUniVcCconnectOutVpi, and adnAtmUniVcCconnectOutVci and used for call tracing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectAdminStatus 3.1.637.3.1.4.37.1.10.1.6
The current administrative status of this Virtual Channel (VC) cross-connection. The 'up' and 'down' states specify whether or not this ATM VC cross-connection is operational.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnAtmAdminStatus  

adnAtmUniVcCconnectOperStatus 3.1.637.3.1.4.37.1.10.1.7
The current Virtual Channel Connection (VCC) call attempt state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmUniOperStatus  

adnAtmUniVcCconnectSourceDest 3.1.637.3.1.4.37.1.10.1.8
Whether this is the source or destination side of the virtual cross-connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmUniSourceDest  

adnAtmUniVcCconnectStatistics 3.1.637.3.1.4.37.1.10.1.9
Whether statistics are enabled for this Virtual Channel (VC) cross-connection. This object is significant only if the type of the Virtual Channel Link (VCL), specified by adnAtmVclType, is set to 'pvc'; otherwise, the statistics status is defined per interface. If set to 'useInterfaceValue', the value defined per interface is used. Common Name: Statistics
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), useInterfaceValue(3)  

adnAtmUniVcCconnectDirectedPath 3.1.637.3.1.4.37.1.10.1.10
Whether this Virtual Channel Connection (VCC) uses a directed path.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnAtmDirectedPath  

adnAtmUniVcCconnectRetryAttempts 3.1.637.3.1.4.37.1.10.1.11
The number of call attempts to make at the fast rate (adnAtmUniVcCconnectFastRetry) before slowing the call attempt rate to adnAtmUniVcCconnectSlowRetry. adnAtmUniVcCconnectOperStatus specifies the current attempt state. This object is significant only if adnAtmUniVcCconnectSourceDest is 'source', adnAtmVclType is 'pvc', and adnAtmVclModeType is 'automatic'. Common Name: Retry Attempts at Fast Rate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectFastRetry 3.1.637.3.1.4.37.1.10.1.12
This timer specifies the amount of time to wait between failed Permanent Virtual Connection (PVC) setup attempts at the fast rate. After making attempts at this rate the number of times specified by adnAtmUniVcCconnectCRetryAttempts, the rate slows to adnAtmUniVcCconnectSlowRetry. This is significant only if adnAtmUniVcCconnectSourceDest is 'source', adnAtmVclType is 'pvc', and adnAtmVclModeType is 'automatic'. Common Name: Wait Time between Fast Retries
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectSlowRetry 3.1.637.3.1.4.37.1.10.1.13
This timer specifies the amount of time to wait between failed Permanent Virtual Connection (PVC) setup attempts at the slow rate. After making attempts at the adnAtmUniVcCconnectFastRetry rate the number of times specified by adnAtmUniVcCconnectRetryAttempts, the rate slows to this rate. This object is significant only if adnAtmUniVcCconnectSourceDest is 'source', adnAtmVclType is 'pvc', and adnAtmVclModeType is 'automatic'. Common Name: Wait Time between Slow Retries
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectRemNumPlan 3.1.637.3.1.4.37.1.10.1.14
The numbering plan of the remote User Network Interface (UNI) for the current Virtual Channel (VC) cross-connection. Common Names: Remote Numbering Plan, Rem Num Plan
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmNumPlan  

adnAtmUniVcCconnectRemPhysAddress 3.1.637.3.1.4.37.1.10.1.15
The address of the current Virtual Channel (VC) cross-connection's remote User Network Interface/Network Network Interface (UNI/NNI). Common Name: Remote Address
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

adnAtmUniVcCconnectRemVpi 3.1.637.3.1.4.37.1.10.1.16
The Virtual Path Identifier (VPI) of the current Virtual Channel (VC) cross-connection's remote User Network Interface/Network Network Interface (UNI/NNI). Common Name: Remote Virtual Path Identifier (VPI)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectRemVci 3.1.637.3.1.4.37.1.10.1.17
The Virtual Channel Identifier (VCI) value of the current Virtual Channel (VC) cross-connection's remote User Network Interface/Network Network Interface (UNI/NNI). Common Name: Remote Virtual Channel Identifier (VCI)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectRemCcnIndex 3.1.637.3.1.4.37.1.10.1.18
The index value of the current Virtual Channel (VC) cross-connection's remote User Network Interface/Network Network Interface (UNI/NNI). Common Name: Remote UNI Cross-Connection Index
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectRemRoutingNodeId 3.1.637.3.1.4.37.1.10.1.19
The identifier of the node connecting the remote User Network Interface/Network Network Interface (UNI/NNI) for the current Virtual Channel (VC) cross-connection. Common Name: Remote Node Identifier
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnAtmUniVcCconnectCumulNodes 3.1.637.3.1.4.37.1.10.1.20
The number of nodes in the connection. If adnAtmUniVcCconnectOperStatus is 'callup', this is the current nodes count; otherwise, it is the nodes count for the last connection. Common Name: Number of Nodes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectMaxTransitDelay 3.1.637.3.1.4.37.1.10.1.21
The maximum allowed transit delay of this Virtual Channel (VC) cross-connection. This object is significant only if the type of the Virtual Channel Link (VCL), specified by adnAtmVplType, is set to 'pvc'. In case of 'svc', the maximum transit delay is defined per interface or could be defined in an Information Element If set to 0, the value defined per interface is used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectCharging 3.1.637.3.1.4.37.1.10.1.22
Whether charging is enabled for this Virtual Channel (VC) cross-connection. This object is significant only if the type of the Virtual Channel Link (VCL), specified by adnAtmVclType, is set to 'pvc'; otherwise, the charging status is defined per interface. If set to 'useInterfaceValue', the value defined per interface is used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), enabled(2), disabled(3), useInterfaceValue(4)  

adnAtmUniVcCconnectCumulTD 3.1.637.3.1.4.37.1.10.1.23
The current cumulative transit delay of this Virtual Channel (VC) cross-connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectCumulMonetaryCst 3.1.637.3.1.4.37.1.10.1.24
The current cumulative monetary cost of this Virtual Channel (VC) cross-connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmUniVcCconnectCauseError 3.1.637.3.1.4.37.1.10.1.25
Global cause of the cross-connect failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notSignificant(1), maxCallAttempts(2), configurationError(3)  

adnAtmUniVcCconnectLastCanpCause 3.1.637.3.1.4.37.1.10.1.26
Last Cell Alcatel Network Protocol (CANP) cause. This nominator, which is read only, is not significant if adnAtmUniVcCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVcCconnectLastErrorNodeID 3.1.637.3.1.4.37.1.10.1.27
The identifier of the node detecting the error. This nominator, which is read only, is not significant if adnAtmUniVcCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnAtmUniVcCconnectLastLocation 3.1.637.3.1.4.37.1.10.1.28
ATM forum location value in the cause information element. This nominator, which is read only, is not significant if adnAtmUniVcCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVcCconnectLastCause 3.1.637.3.1.4.37.1.10.1.29
ATM forum cause value in the cause information element. This nominator, which is read only, is not significant if adnAtmUniVcCconnectCauseError is equal to 'notsignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVcCconnectLastDiag 3.1.637.3.1.4.37.1.10.1.30
ATM forum diagnostic value in the cause information element. This nominator, which is read only, is not significant if adnAtmUniVcCconnectCauseError is equal to 'notsignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVcCconnectRemNodeMacNum 3.1.637.3.1.4.37.1.10.1.31
The machine number part of adnAtmUniVpCconnectRemRoutingNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVcCconnectRemNodeAreaNum 3.1.637.3.1.4.37.1.10.1.32
The area number part of adnAtmUniVcCconnectRemRoutingNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVcCconnectErrorNodeMacNum 3.1.637.3.1.4.37.1.10.1.33
The machine number part of adnAtmUniVcCconnectLastErrorNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVcCconnectErrorNodeAreaNum 3.1.637.3.1.4.37.1.10.1.34
The area number part of adnAtmUniVcCconnectLastErrorNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVcCconnectLastChassis 3.1.637.3.1.4.37.1.10.1.35
The chassis number detecting the error. This nominator, which is read only, is not significant if adnAtmUniVcCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVcCconnectLastSlot 3.1.637.3.1.4.37.1.10.1.36
The slot number of the board detecting the error. This nominator, which is read only, is not significant if adnAtmUniVcCconnectCauseError is equal to 'notSignificant'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmUniVcCconnectPvcDescr 3.1.637.3.1.4.37.1.10.1.37
This object contains the Permanent Virtual Connection (PVC) description inserted in each charging ticket generated for this Virtual Channel (VC) cross-connection. This object is significant only if the type of the Virtual Channel Link (VCL), specified by adnAtmVclType, is set to 'pvc'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnAtmCniVcCconnectTable 3.1.637.3.1.4.37.1.11
The Virtual Channel (VC) cross-connect table for the inter-node ATM interfaces (Cell alcatel Network protocol Interfaces (CNIs)).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmCniVcCconnectEntry

adnAtmCniVcCconnectEntry 3.1.637.3.1.4.37.1.11.1
An entry in the Cell alcatel Network protocol Interface (CNI) Virtual Channel (VC) cross-connect table. There is one entry for each VC cross-connection on a CNI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmCniVcCconnectEntry  

adnAtmCniVcCconnectIndex 3.1.637.3.1.4.37.1.11.1.1
The index of the cross-connection for this Virtual Channel Connection (VCC) on this interface. In a point-to-point cross-connection, the index equals 0.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmCniVcCconnectOutIfIndex 3.1.637.3.1.4.37.1.11.1.2
The ifIndex of the output ATM interface from this node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnAtmCniVcCconnectOutVpi 3.1.637.3.1.4.37.1.11.1.3
The Virtual Path Identifier (VPI) of this connection on the output ATM interface from this node. In conjunction with adnAtmCniVcCconnectOutIfIndex, this VPI can be used for path tracing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmCniVcCconnectOutVci 3.1.637.3.1.4.37.1.11.1.4
The Virtual Channel Identifier (VCI) of this node's output interface. This cross-connection exits this node on another VCI. This value can be combined with adnAtmCniVcCconnectOutIfIndex and adnAtmCniVcCconnectOutVpi and used for call tracing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmCniVcCconnectOutCcnIndex 3.1.637.3.1.4.37.1.11.1.5
The cross-connection index of the Virtual Path Identifier/Virtual Channel Identifier (VPI/VCI) of this node's output interface. This value can be used for call tracing if combined with adnAtmCniVcCconnectOutIfIndex, adnAtmCniVcCconnectOutVpi, and adnAtmCniVcCconnectOutVci.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmCniVcCconnectAdminStatus 3.1.637.3.1.4.37.1.11.1.6
The current administrative status of this Virtual Channel (VC) cross-connection. The 'up' and 'down' states indicate whether or not this ATM VC cross-connection is operational.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmAdminStatus  

adnAtmCniVcCconnectOperStatus 3.1.637.3.1.4.37.1.11.1.7
The current Virtual Channel Connection (VCC) call attempt state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmCniOperStatus  

adnAtmCniVcCconnectSourceDest 3.1.637.3.1.4.37.1.11.1.8
Whether this is the source or destination side of the cross-connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmCniSourceDest  

adnAtmCniVcCconnectStatistics 3.1.637.3.1.4.37.1.11.1.9
Whether statistics are enabled for this Virtual Channel (VC) cross-connection. This object is significant only if the type of the Virtual Channel Link (VCL), specified by adnAtmVclType, is set to 'pvc'; otherwise, the statistics status is defined per interface. If set to 'useInterfaceValue', the value defined per interface is used. Common Name: Statistics
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), useInterfaceValue(3)  

adnAtmCniVcCconnectDirectedPath 3.1.637.3.1.4.37.1.11.1.10
Whether this Virtual Channel Connection (VCC) uses a directed path.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmDirectedPath  

adnAtmVpcDirRoutTable 3.1.637.3.1.4.37.1.12
This table contains the directed path, used to set up point-to-point permanent Virtual Path Connections (VPCs). A directed path is composed of a list of node identifier and outgoing line identifiers. This table is configured only in the origin node of the cross-connection. The path between the origin and the destination node could be partly or completely described by the list, but it is only used if adnAtmUniVpCconnectDirectedPath is set to 'enabled'.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmVpcDirRoutEntry

adnAtmVpcDirRoutEntry 3.1.637.3.1.4.37.1.12.1
An entry in the adnAtmVpcDirRoutTable. There is one entry for each element of each list specifing a directed path.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmVpcDirRoutEntry  

adnAtmVpcDirRoutIndex 3.1.637.3.1.4.37.1.12.1.1
The index of an element in the list of this Virtual Path Connection (VPC).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmVpcDirRoutNodeId 3.1.637.3.1.4.37.1.12.1.2
The identifier of the next node to be used to reach the destination node, for this Virtual Path Connection (VPC).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnAtmVpcDirRoutOutChassis 3.1.637.3.1.4.37.1.12.1.3
The chassis number, within the current node, supporting the line used to reach the next node, specified by adnAtmVpcDirRoutNodeId.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpcDirRoutOutSlot 3.1.637.3.1.4.37.1.12.1.4
The slot number, within the current node, supporting the line used to reach the next node, specified by adnAtmVpcDirRoutNodeId.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVpcDirRoutOutLine 3.1.637.3.1.4.37.1.12.1.5
The line number, within the current node, used to reach the next node, specified by adnAtmVpcDirRoutNodeId.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmVpcDirRoutFlag 3.1.637.3.1.4.37.1.12.1.6
Whether only the outgoing line specified must be used to reach the next node or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmDirRoutFlag  

adnAtmVpcDirRoutNodeMacNum 3.1.637.3.1.4.37.1.12.1.7
The machine number part of adnAtmVpcDirRoutNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmVpcDirRoutNodeAreaNum 3.1.637.3.1.4.37.1.12.1.8
The area number part of adnAtmVpcDirRoutNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmVccDirRoutTable 3.1.637.3.1.4.37.1.13
This table contains the directed path, used to set up point-to-point permanent Virtual Channel Connections (VPCs). A directed path is composed of a list of node identifier and outgoing line identifiers. This table is configured only in the origin node of the cross-connection. The path between the origin and the destination node could be partly or completely described by the list, but it is only used if adnAtmUniVcCconnectDirectedPath is set to 'enabled'.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmVccDirRoutEntry

adnAtmVccDirRoutEntry 3.1.637.3.1.4.37.1.13.1
An entry in the adnAtmVccDirRoutTable. There is one entry for each element of each list specifing a directed path.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmVccDirRoutEntry  

adnAtmVccDirRoutIndex 3.1.637.3.1.4.37.1.13.1.1
The index of an element in the list of this Virtual Channel Connection (VCC).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmVccDirRoutNodeId 3.1.637.3.1.4.37.1.13.1.2
The identifier of the next node to be used to reach the destination node, for this Virtual Channel Connection (VCC).
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnAtmVccDirRoutOutChassis 3.1.637.3.1.4.37.1.13.1.3
The chassis number, within the current node, supporting the line used to reach the next node, specified by adnAtmVccDirRoutNodeId.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVccDirRoutOutSlot 3.1.637.3.1.4.37.1.13.1.4
The slot number, within the current node, supporting the line used to reach the next node, specified by adnAtmVccDirRoutNodeId.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVccDirRoutOutLine 3.1.637.3.1.4.37.1.13.1.5
The line number, within the current node, used to reach the next node, specified by adnAtmVccDirRoutNodeId.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmVccDirRoutFlag 3.1.637.3.1.4.37.1.13.1.6
Whether only the outgoing line specified must be used to reach the next node or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmDirRoutFlag  

adnAtmVccDirRoutNodeMacNum 3.1.637.3.1.4.37.1.13.1.7
The machine number part of adnAtmVccDirRoutNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmVccDirRoutNodeAreaNum 3.1.637.3.1.4.37.1.13.1.8
The area number part of adnAtmVccDirRoutNodeID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmReachAddrTable 3.1.637.3.1.4.37.1.14
This table contains either: - The list of prefix addresses which can be reached through the Interim Inter-switch Signalling Protocol (IISP) link supported by the associated ATM interface. Each prefix entry may be associated with a list of addresses specified in the AdnAtmReachAssocAddrTable - The list of complete addresses registered with Interim Local Management Interface (ILMI) or configured if the Multiple Subscriber Number (MSN) service is offered.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmReachAddrEntry

adnAtmReachAddrEntry 3.1.637.3.1.4.37.1.14.1
An entry in the adnAtmReachAddrTable. There is one entry for each element of the list.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmReachAddrEntry  

adnAtmReachAddrIndex 3.1.637.3.1.4.37.1.14.1.1
The index of an element in the list.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmReachAddrNumPlan 3.1.637.3.1.4.37.1.14.1.2
The number plan of the prefix or complete address specified in adnAtmReachAddrNumber. Common Names: Numbering Plan, Num Plan
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmNumPlan  

adnAtmReachAddrNumberLength 3.1.637.3.1.4.37.1.14.1.3
The number of digits of the prefix address specified in adnAtmReachAddrNumber. If adnAtmReachAddrNumPlan is set to 'private', a digit size is equal to half a byte otherwise it is equal to one byte.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmReachAddrNumber 3.1.637.3.1.4.37.1.14.1.4
The prefix address which can be reached through the Interim Inter-switch Signalling Protocol (IISP) link supported by the associated ATM interface or the complete address registered with Interim Local Management Interface (ILMI) or configured if the Multiple Subscriber Number (MSN) service is offered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

adnAtmReachAddrAssocIndex 3.1.637.3.1.4.37.1.14.1.5
The index of the list of the associated addresses in the adnAtmReachAssocAddrTable. This object could be significant only if the associated ATM interface support an Interim Inter-switch Signalling Protocol (IISP) link. Not significant value (65535) indicates that there is no associated address in adnAtmReachAssocAddrTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmReachAssocAddrTable 3.1.637.3.1.4.37.1.15
This table contains all the lists of associated addresses of prefix addresses described in the adnAtmReachAddrTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmReachAssocAddrEntry

adnAtmReachAssocAddrEntry 3.1.637.3.1.4.37.1.15.1
An entry in the adnAtmReachAssocAddrTable. There is one entry for each element of each list.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmReachAssocAddrEntry  

adnAtmReachAssocAddrIndex 3.1.637.3.1.4.37.1.15.1.1
The index of a list in the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmReachAssocAddrNumIndex 3.1.637.3.1.4.37.1.15.1.2
The index of an element in a list.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmReachAssocAddrNumPlan 3.1.637.3.1.4.37.1.15.1.3
The number plan of the associated address specified by adnAtmReachAssocAddrAddress. Common Names: Numbering Plan, Num Plan
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnAtmNumPlan  

adnAtmReachAssocAddrAddress 3.1.637.3.1.4.37.1.15.1.4
The associated address used to transit through an other network which has not the same number plan.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

adnAtmInterfacePerfTable 3.1.637.3.1.4.37.1.16
This table contains counters related to the ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmInterfacePerfEntry

adnAtmInterfacePerfEntry 3.1.637.3.1.4.37.1.16.1
An entry in the adnAtmInterfacePerfTable. There is one entry for each ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmInterfacePerfEntry  

adnAtmInterfacePerfTrmAllocBwVpiForVcc 3.1.637.3.1.4.37.1.16.1.1
The allocated bandwidth, in the transmit direction, for all Virtual Path Identifiers (VPIs) dedicated to Virtual Channel Connections (VCCs). If all VPIs dedicated to VCCs have no bandwidth limitation (adnAtmVpiVccTrmBandwidth = 0), this counter equals 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfRcvAllocBwVpiForVcc 3.1.637.3.1.4.37.1.16.1.2
The allocated bandwidth, in the receiving direction, for all Virtual Path Identifiers (VPIs) dedicated to Virtual Channel Connections (VCCs). If all VPIs dedicated to VCCs have no bandwidth limitation (adnAtmVpiVccRcvBandwidth = 0), this counter equals 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfTrmAllocBwVpcs 3.1.637.3.1.4.37.1.16.1.3
The allocated bandwidth, in the transmit direction, for all Virtual Path Connections (VPCs) created on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfRcvAllocBwVpcs 3.1.637.3.1.4.37.1.16.1.4
The allocated bandwidth, in the receiving direction, for all Virtual Path Connections (VPCs) created on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfTrmAllocBwVccs 3.1.637.3.1.4.37.1.16.1.5
The allocated bandwidth, in the transmit direction, for all Virtual Channel Connections (VCCs) having a Virtual Path Identifier (VPI) with no bandwidth limiation, created on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfRcvAllocBwVccs 3.1.637.3.1.4.37.1.16.1.6
The allocated bandwidth, in the receiving direction, for all Virtual Channel Connections (VCCs) having a Virtual Path Identifier (VPI) with no bandwidth limiation, created on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfPPtpVpcs 3.1.637.3.1.4.37.1.16.1.7
The number of permanent point-to-point Virtual Path Connections (VPCs) on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfSPtpVpcs 3.1.637.3.1.4.37.1.16.1.8
The number of switched point-to-point Virtual Path Connections (VPCs) on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfPPtmRootVpcs 3.1.637.3.1.4.37.1.16.1.9
The number of permanent point-to-multipoint root Virtual Path Connections (VPCs) on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfSPtmRootVpcs 3.1.637.3.1.4.37.1.16.1.10
The number of switched point-to-multipoint root Virtual Path Connections (VPCs) on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfPPtmLeafVpcs 3.1.637.3.1.4.37.1.16.1.11
The number of permanent point-to-multipoint leaf Virtual Path Connections (VPCs) on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfacePerfSPtmLeafVpcs 3.1.637.3.1.4.37.1.16.1.12
The number of switched point-to-multipoint leaf Virtual Path Connections (VPCs) on this ATM interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVpiVccPerfTable 3.1.637.3.1.4.37.1.17
This table contains counters related to the Virtual Channel Link (VCL) of each Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs) on an ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmVpiVccPerfEntry

adnAtmVpiVccPerfEntry 3.1.637.3.1.4.37.1.17.1
An entry in the adnAtmVpiVccPerfTable. There is one entry for each Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs) on an ATM interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmVpiVccPerfEntry  

adnAtmVpiVccPerfTrmAllocBwVccs 3.1.637.3.1.4.37.1.17.1.1
The allocated bandwidth, in the transmit direction, for all Virtual Channel Connections (VCCs).If the VPI dedicated to VCCs has no bandwidth limitation, this counter equals 0 and the allocated bandwidth is accounted in the counter adnAtmInterfacePerfTrmAllocBwVccs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVpiVccPerfRcvAllocBwVccs 3.1.637.3.1.4.37.1.17.1.2
The allocated bandwidth, in the receiving direction, for all Virtual Channel Connections (VCCs).If the VPI dedicated to VCCs has no bandwidth limitation, this counter equals 0 and the allocated bandwidth is accounted in the counter adnAtmInterfacePerfRcvAllocBwVccs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVpiVccPerfPPtpVccs 3.1.637.3.1.4.37.1.17.1.3
The number of permanent point-to-point Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVpiVccPerfSPtpVccs 3.1.637.3.1.4.37.1.17.1.4
The number of switched point-to-point Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVpiVccPerfPPtmRootVccs 3.1.637.3.1.4.37.1.17.1.5
The number of permanent point-to-multipoint root Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVpiVccPerfSPtmRootVccs 3.1.637.3.1.4.37.1.17.1.6
The number of switched point-to-multipoint root Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVpiVccPerfPPtmLeafVccs 3.1.637.3.1.4.37.1.17.1.7
The number of permanent point-to-multipoint leaf Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVpiVccPerfSPtmLeafVccs 3.1.637.3.1.4.37.1.17.1.8
The number of switched point-to-multipoint leaf Virtual Channel Connections (VCCs) on this Virtual Path Identifier (VPI) dedicated to Virtual Channel Connections (VCCs).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVplPerfTable 3.1.637.3.1.4.37.1.18
This table contains counters relative to each Virtual Path Link (VPL).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmVplPerfEntry

adnAtmVplPerfEntry 3.1.637.3.1.4.37.1.18.1
An entry in the adnAtmVplPerfTable. There is one entry for each Virtual Path Link (VPL).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmVplPerfEntry  

adnAtmVplPerfRcvCellForwarded 3.1.637.3.1.4.37.1.18.1.1
The number of cells received and forwarded (after police processing) on the Virtual Path Link (VPL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVplPerfRcvCellDiscarded 3.1.637.3.1.4.37.1.18.1.2
The number of cells received on the Virtual Path Link (VPL) and discarded by the police processing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVplPerfRcvCellVsaANonConform 3.1.637.3.1.4.37.1.18.1.3
The number of cells received on the Virtual Path Link (VPL) and declared non conform by the Virtual Scheduling Algorithm (VSA) A of the police processing. This object is significant only if the VSA A is enabled. The VSA A is enabled or not according to the ATM Transfer Capability (ATC) of the VPL.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVplPerfRcvCellVsaBNonConform 3.1.637.3.1.4.37.1.18.1.4
The number of cells received on the Virtual Path Link (VPL) and declared non conform by the Virtual Scheduling Algorithm (VSA) B of the police processing. Whatever the ATM Transfer Capability (ATC) of the VPL, the VSA B is always enabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVplPerfRcvCellTagged 3.1.637.3.1.4.37.1.18.1.5
The number of cells received on the Virtual Path Link (VPL) and tagged by the police processing. This object is significant only if the tagging option is enabled on the VPL.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVclPerfTable 3.1.637.3.1.4.37.1.19
This table contains counters relative to each Virtual Channel Link (VCL).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmVclPerfEntry

adnAtmVclPerfEntry 3.1.637.3.1.4.37.1.19.1
An entry in the adnAtmVclPerfTable. There is one entry for each Virtual Channel Link (VCL).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmVclPerfEntry  

adnAtmVclPerfRcvCellForwarded 3.1.637.3.1.4.37.1.19.1.1
The number of cells received and forwarded (after police processing) on the Virtual Channel Link (VCL).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVclPerfRcvCellDiscarded 3.1.637.3.1.4.37.1.19.1.2
The number of cells received on the Virtual Channel Link (VCL) and discarded by the police processing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVclPerfRcvCellVsaANonConform 3.1.637.3.1.4.37.1.19.1.3
The number of cells received on the Virtual Channel Link (VCL) and declared non conform by the Virtual Scheduling Algorithm (VSA) A of the police processing. This object is significant only if the VSA A is enabled. The VSA A is enabled or not according to the ATM Transfer Capability (ATC) of the VCL.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVclPerfRcvCellVsaBNonConform 3.1.637.3.1.4.37.1.19.1.4
The number of cells received on the Virtual Channel Link (VCL) and declared non conform by the Virtual Scheduling Algorithm (VSA) B of the police processing. Whatever the ATM Transfer Capability (ATC) of the VCL, the VSA B is always enabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmVclPerfRcvCellTagged 3.1.637.3.1.4.37.1.19.1.5
The number of cells received on the Virtual Channel Link (VCL) and tagged by the police processing. This object is significant only if the tagging option is enabled on the VCL.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmAal5PerfTable 3.1.637.3.1.4.37.1.20
This table is the extension of the aal5VCCTable, described in RFC 1695. This table contains ATM Adaptation Layer 5 (AAL5) performance counters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmAal5PerfEntry

adnAtmAal5PerfEntry 3.1.637.3.1.4.37.1.20.1
An entry in the adnAtmAal5PerfTable. There is one entry for each ATM Adaptation Layer 5 (AAL5) Virtual Channel Connection (VCC).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmAal5PerfEntry  

adnAtmAal5PerfLengthErrors 3.1.637.3.1.4.37.1.20.1.1
The number of ATM Adaptation Layer 5 (AAL5) Common Part Convergence Sublayer (CPCS) PDUs discarded on this Virtual Channel Link (VCL) because the value of the length field in the PDU trailer is not consistent with the actual PDU payload length.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmAal5PerfCpiErrors 3.1.637.3.1.4.37.1.20.1.2
The number of ATM Adaptation Layer 5 (AAL5) Common Part Convergence Sublayer (CPCS) PDUs discarded on this Virtual Channel Link (VCL) because the value of the Common Part Interface (CPI) field in the PDU trailer is not 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFRAIWMIB 3.1.637.3.1.5.17
OBJECT IDENTIFIER    

adnFRAIWConfTable 3.1.637.3.1.5.17.1
This table contains the configuration parameters of the frame relay (FR) logical line. There is one entry for each FR logical line.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFRAIWConfEntry

adnFRAIWConfEntry 3.1.637.3.1.5.17.1.1
An entry in the adnFRAIWConfTable. There is one entry for each frame relay logical line.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFRAIWConfEntry  

adnFRAIWConfIUNIifIndex 3.1.637.3.1.5.17.1.1.1
The ifIndex of the internal user to network interface (I-UNI) bearing the ATM virtual channel connection (VCC) associated with this frame relay logical line. Common Name: I-UNI ifIndex
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnFRAIWConfVpi 3.1.637.3.1.5.17.1.1.2
The virtual path identifier (VPI) of the ATM virtual channel connection (VCC) bearing the frame relay logical line. Common Name: Virtual Path Identifier, VPI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFRAIWConfVci 3.1.637.3.1.5.17.1.1.3
The virtual connection identifier (VCI) of the ATM virtual channel connection (VCC) bearing the frame relay logical line. Common name: Virtual Channel Identifier, VCI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFRAIWConfLogLineType 3.1.637.3.1.5.17.1.1.4
The type of service using the frame relay logical line: - franpOverATM : FRANP trunking over ATM - netIWsc1 : network interworking scenario 1 (defined by FRF.5) - netIWsc2OneToOne : network interworking scenario 2 with each FR connection mapped to a single ATM virtual channel connection (defined by FRF.5) - netIWsc2ManyToOne: network interworking scenario 2 with multiple FR connections multiplexed into a single ATM virtual channel connection (defined by FRF.5) - serIW : service interworking (defined by FRF.8) - issc : NMS-ISS connection over ATM - ipfw : IP Forwarding service Common Name: Logical Line Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), franpOverAtm(2), netIWsc2OneToOne(3), netIWsc2ManyToOne(4), netIWsc1(5), serIW(6), issc(7), ipfw(8)  

adnFRAIWConfAalType 3.1.637.3.1.5.17.1.1.5
The type of ATM Adaptation Layer used on the ATM virtual channel connection (VCC) bearing the frame relay logical line. Common Name: ATM Adaptation Layer
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER aal5(1), aal34(2)  

adnFRAIWConfInitCLP 3.1.637.3.1.5.17.1.1.6
The segmentation process of every frame for the frame relay logical line generates ATM cells. This variable defines how the cell loss priority (CLP) bit for each of those cells is initialized. The names of the valid values are borrowed from the Frame Relay Forum implementation agreements concerning FR/ATM interworking (FRF.5 and FRF.8): - mode1 : The discard eligibility bit in the Q.922 core frame is copied to the CLP bit. - mode20 : Every ATM cell's CLP bit is set to zero. This mode is the only one allowed if the FR logical line is bearing a FRANP trunk or an ISS connection. - mode21 : Every ATM cell's CLP bit is set to one. This mode is the only one allowed if the FR logical line is bearing an IP forwarding connection. Common Name: Cell Loss Priority Bit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER mode1(1), mode20(2), mode21(3)  

adnFRAIWConfTrapEnable 3.1.637.3.1.5.17.1.1.7
This indicates if trap generation is enabled on the frame relay logical line in case of reception of an over-sized AAL Service Data Unit. Common Name: Trap
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFRAIWConfStatisticsEnable 3.1.637.3.1.5.17.1.1.8
This indicates if historical statistics generation is enabled on the frame relay logical line. Common Name: Statistics
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnFRAIWConfSegmPcr 3.1.637.3.1.5.17.1.1.9
The Peak Cell Rate (PCR) of the ATM flow generated on the logical line by the segmentation process of frames. Common name: Segmentation Peak Cell Rate (PCR)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFRAIWConfSegmScr 3.1.637.3.1.5.17.1.1.10
The Sustainable Cell Rate (SCR) of the ATM flow generated on the logical line by the segmentation process of frames when the segmentation process generates a variable bit rate flow. When the segmentation process generates a constant bit rate flow, the segmentation SCR is set to 0. Common name: Segmentation Sustainable Cell Rate (SCR)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFRAIWConfSegmMbs 3.1.637.3.1.5.17.1.1.11
The maximum number of cells transmitted at the Peak Cell Rate (PCR) in the ATM flow generated on the logical line when the segmentation process generates a variable bit rate flow. When the segmentation process generates a constant bit rate flow, the segmentation maximum burst size is set to 0. Common name: Segmentation Maximum Burst Size (MBS)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFRAIWConfCosRtOutOctets 3.1.637.3.1.5.17.1.1.12
Number of Class 1 Octets transmitted by aafd.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFRAIWConfCosRtOutPkts 3.1.637.3.1.5.17.1.1.13
Number of Class 1 packets (frame or subframes) transmitted by aafd.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFRAIWConfCosRtOutErrors 3.1.637.3.1.5.17.1.1.14
Number of errors while transmitting Class 1 data by aafd.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFRAIWConfCosNrtOutOctets 3.1.637.3.1.5.17.1.1.15
Number of Class 2 Octets transmitted by aafd.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFRAIWConfCosNrtOutPkts 3.1.637.3.1.5.17.1.1.16
Number of Class 2 packets (frame or subframes) transmitted by aafd.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFRAIWConfCosNrtOutErrors 3.1.637.3.1.5.17.1.1.17
Number of errors while transmitting Class 2 data by aafd.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnFrAtmSerIWTable 3.1.637.3.1.5.17.2
This table contains the parameters of the frame relay (FR) logical line. There is one entry for each FR logical line bearing service interworking.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnFrAtmSerIWEntry

adnFrAtmSerIWEntry 3.1.637.3.1.5.17.2.1
An entry in the adnFrAtmSerIWTable. There is one entry for each frame relay logical line bearing service interworking.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrAtmSerIWEntry  

adnFrAtmSerIWInitEFCI 3.1.637.3.1.5.17.2.1.1
The segmentation process of every frame for the frame relay logical line generates ATM cells. This variable defines how the explicit forward congestion indication (EFCI) bit for each of those cells is initialized. The names of the valid values are borrowed from the Frame Relay Forum implementation agreement concerning FR/ATM service interworking (FRF.8): - mode1 : The FECN bit in the Q.922 core frame is copied to the EFCI bit. - mode2 : Every ATM cell's EFCI bit is set to zero. Common Name: Explicit Forward Congestion Indication Bit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER mode1(1), mode2(2)  

adnFrAtmSerIWInitDE 3.1.637.3.1.5.17.2.1.2
This variable defines how the discard eligibility (DE) bit for each frame reassembled from cells is initialized on a FR logical line used for service interworking. The names of the valid values are borrowed from the Frame Relay Forum implementation agreement concerning FR/ATM service interworking (FRF.8): - mode20 : The DE bit is set to zero. - mode21 : The DE bit is set to one. Common Name: Discard Eligibility Bit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER mode20(1), mode21(2)  

adnFrAtmSerIWEncapsMode 3.1.637.3.1.5.17.2.1.3
The way to handle the upper layer user protocol encapsulation on the frame relay logical line: - transparent : the encapsulations are forwarded unaltered. No fragmentation/reassembly is performed. - translation : The mapping between RFC1490 and RFC1483 is performed. No fragmentation/reassembly is performed. Common Name: Encapsulation Mode
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER transparent(1), translation(2)  

adnFrAtmSerIWAddrDLCI 3.1.637.3.1.5.17.2.1.4
The value of this object identifies the DLCI used for this FR logical line when forwarding a frame to the FR layer. The value of this object is always equal to 16. This value is used when configuring the FR PVC of the FR access on top of this logical line. Common Name: DLCI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFrAtmSerIWUserN391 3.1.637.3.1.5.17.2.1.5
The value of this object identifies the User-side N391 full status polling cycle value for this logical port. Common Name: userN391
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFrAtmSerIWUserN392 3.1.637.3.1.5.17.2.1.6
The value of this object identifies the User-side N392 error threshold value for this logical port. Common Name: userN392
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFrAtmSerIWUserN393 3.1.637.3.1.5.17.2.1.7
The value of this object identifies the User-side N393 monitored events count value for this logical port. Common Name: userN393
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFrAtmSerIWUserT391 3.1.637.3.1.5.17.2.1.8
The value of this object identifies the User-side T391 link integrity verification polling timer value for this logical port. Common Name: userT391
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFrAtmSerIWNetN392 3.1.637.3.1.5.17.2.1.9
The value of this object identifies the Network- side N392 error threshold value for this logical port. Common Name: NetN392
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFrAtmSerIWNetN393 3.1.637.3.1.5.17.2.1.10
The value of this object identifies the Network- side N393 monitored events count value for this logical port. Common Name: NetN393
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFrAtmSerIWNetT392 3.1.637.3.1.5.17.2.1.11
The value of this object identifies the Network- side T392 polling verification timer value for this logical port. Common Name: NetT392
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnUCNodeErrorsSfas 3.1.637.3.1.9.1.1
OBJECT IDENTIFIER    

adnUCNodeErrorsSfasInternalErr 3.1.637.3.1.9.1.1.1
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgs 3.1.637.3.1.9.1.2
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsInvalidEvent 3.1.637.3.1.9.1.2.1
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsTimingProblem 3.1.637.3.1.9.1.2.2
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsSoftwareError 3.1.637.3.1.9.1.2.3
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsTooLongSll 3.1.637.3.1.9.1.2.4
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNullInmpSend 3.1.637.3.1.9.1.2.10
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsInmpSend 3.1.637.3.1.9.1.2.11
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsControlBlock 3.1.637.3.1.9.1.2.12
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsPfxiAccess 3.1.637.3.1.9.1.2.13
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsStatusRequest 3.1.637.3.1.9.1.2.14
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNoFullConfig 3.1.637.3.1.9.1.2.15
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNoDelta 3.1.637.3.1.9.1.2.16
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNoRollback 3.1.637.3.1.9.1.2.17
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBoardStatus 3.1.637.3.1.9.1.2.18
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsLoadFailed 3.1.637.3.1.9.1.2.19
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsTransList 3.1.637.3.1.9.1.2.20
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsEventState 3.1.637.3.1.9.1.2.30
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsTimeout 3.1.637.3.1.9.1.2.31
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsProcResetRequest 3.1.637.3.1.9.1.2.50
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsProcStatusRequest 3.1.637.3.1.9.1.2.51
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsProcNoSll 3.1.637.3.1.9.1.2.52
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsSllOpen 3.1.637.3.1.9.1.2.53
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNoDownloadCmdFile 3.1.637.3.1.9.1.2.54
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsUndefFileInSll 3.1.637.3.1.9.1.2.55
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsSendSll 3.1.637.3.1.9.1.2.56
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNoSmiFileStatus 3.1.637.3.1.9.1.2.57
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBadSwInd 3.1.637.3.1.9.1.2.58
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsDataSetError 3.1.637.3.1.9.1.2.59
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBadFwSll 3.1.637.3.1.9.1.2.60
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBadFwInd 3.1.637.3.1.9.1.2.61
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsProcDown 3.1.637.3.1.9.1.2.62
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsGeneralError 3.1.637.3.1.9.1.2.69
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsLocNoSuchInstance 3.1.637.3.1.9.1.2.70
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsLocNoSuchService 3.1.637.3.1.9.1.2.71
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsLocError 3.1.637.3.1.9.1.2.72
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsIacsSend 3.1.637.3.1.9.1.2.73
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBadPfxiFile 3.1.637.3.1.9.1.2.74
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsLocQaFailed 3.1.637.3.1.9.1.2.75
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsFwDs 3.1.637.3.1.9.1.2.201
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsFwSll 3.1.637.3.1.9.1.2.202
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsFwDupFile 3.1.637.3.1.9.1.2.203
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsFwOpenFail 3.1.637.3.1.9.1.2.204
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNoFwInv 3.1.637.3.1.9.1.2.205
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsUncomAvail 3.1.637.3.1.9.1.2.210
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsUncomRunning 3.1.637.3.1.9.1.2.211
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsScriptFail 3.1.637.3.1.9.1.2.212
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsCopyError 3.1.637.3.1.9.1.2.213
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsSysError 3.1.637.3.1.9.1.2.214
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsCleanDir 3.1.637.3.1.9.1.2.215
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsFileError 3.1.637.3.1.9.1.2.216
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsInstallDsError 3.1.637.3.1.9.1.2.217
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsDeleteBrd 3.1.637.3.1.9.1.2.218
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsMergeDelta 3.1.637.3.1.9.1.2.219
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsCuSw 3.1.637.3.1.9.1.2.220
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBrdSw 3.1.637.3.1.9.1.2.221
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsCuConfig 3.1.637.3.1.9.1.2.222
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBrdConfig 3.1.637.3.1.9.1.2.223
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsSfasMib 3.1.637.3.1.9.1.2.224
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBkupNeCuCodeDs 3.1.637.3.1.9.1.2.225
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBkupNeCuConfDs 3.1.637.3.1.9.1.2.226
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBkupBrdConfDs 3.1.637.3.1.9.1.2.227
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBkupPrCodeDs 3.1.637.3.1.9.1.2.228
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBkupCuCodeFl 3.1.637.3.1.9.1.2.229
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBkupCuConfFl 3.1.637.3.1.9.1.2.230
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBkupBrdConfFl 3.1.637.3.1.9.1.2.231
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBkupPrCodeFl 3.1.637.3.1.9.1.2.232
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsAllCuConfDs 3.1.637.3.1.9.1.2.233
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsReplCuConfDs 3.1.637.3.1.9.1.2.234
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsReplSfasMibDs 3.1.637.3.1.9.1.2.235
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsAppCuCodeDs 3.1.637.3.1.9.1.2.236
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsAppCuDataDs 3.1.637.3.1.9.1.2.237
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsWriteCuCodeDs 3.1.637.3.1.9.1.2.238
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsBkupCuCodeDs 3.1.637.3.1.9.1.2.239
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsAppCuSwDs 3.1.637.3.1.9.1.2.240
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsUpdBrdConfDs 3.1.637.3.1.9.1.2.241
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsAllBrdConfDs 3.1.637.3.1.9.1.2.242
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsDupFwInv 3.1.637.3.1.9.1.2.300
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNotOnUptList 3.1.637.3.1.9.1.2.301
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNoDldCmdFile 3.1.637.3.1.9.1.2.302
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsTooManySwp 3.1.637.3.1.9.1.2.303
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNoFwInvFile 3.1.637.3.1.9.1.2.304
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNoSrliFile 3.1.637.3.1.9.1.2.305
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNoSllFile 3.1.637.3.1.9.1.2.350
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsDeclareSm 3.1.637.3.1.9.1.2.400
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsInstallSm 3.1.637.3.1.9.1.2.401
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsDelcareCm 3.1.637.3.1.9.1.2.402
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsVerifySm 3.1.637.3.1.9.1.2.403
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsActivateSm 3.1.637.3.1.9.1.2.404
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsIsolateCm 3.1.637.3.1.9.1.2.405
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsMajorVersionCm 3.1.637.3.1.9.1.2.406
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsValidateSm 3.1.637.3.1.9.1.2.407
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsSuppressSm 3.1.637.3.1.9.1.2.408
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsDeactivateCm 3.1.637.3.1.9.1.2.409
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsUnknownVsn 3.1.637.3.1.9.1.2.450
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsConfirmLinkTO 3.1.637.3.1.9.1.2.451
OBJECT IDENTIFIER    

adnUCNodeErrorsNmgsNmciMsgFail 3.1.637.3.1.9.1.2.452
OBJECT IDENTIFIER    

adnUCNodeErrorsFrs 3.1.637.3.1.9.1.5
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsNoDelete 3.1.637.3.1.9.1.5.1
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsNotConfigPar 3.1.637.3.1.9.1.5.2
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsInvalLength 3.1.637.3.1.9.1.5.5
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsNoMemory 3.1.637.3.1.9.1.5.6
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsInvalAddrLength 3.1.637.3.1.9.1.5.7
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsInvalType 3.1.637.3.1.9.1.5.8
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsFailLimit 3.1.637.3.1.9.1.5.9
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsFailList 3.1.637.3.1.9.1.5.10
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsFailString 3.1.637.3.1.9.1.5.11
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsFailScan 3.1.637.3.1.9.1.5.19
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsNotUpdPar 3.1.637.3.1.9.1.5.20
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsInvIntfTranId 3.1.637.3.1.9.1.5.257
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfNotCre 3.1.637.3.1.9.1.5.258
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfNotIns 3.1.637.3.1.9.1.5.259
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfTransNotCre 3.1.637.3.1.9.1.5.260
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfDelWithVC 3.1.637.3.1.9.1.5.264
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfDelFail 3.1.637.3.1.9.1.5.266
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfLlceFail 3.1.637.3.1.9.1.5.267
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfInconsTran 3.1.637.3.1.9.1.5.268
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfInvalTranType 3.1.637.3.1.9.1.5.269
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfAddMod 3.1.637.3.1.9.1.5.270
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsDelTransFail 3.1.637.3.1.9.1.5.271
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfIntErr 3.1.637.3.1.9.1.5.272
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsVCInconsTran 3.1.637.3.1.9.1.5.513
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsInvVCTranId 3.1.637.3.1.9.1.5.1025
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfNotUp 3.1.637.3.1.9.1.5.1026
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsVCNotCre 3.1.637.3.1.9.1.5.1027
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsVCNotIns 3.1.637.3.1.9.1.5.1028
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsVCTransNotCre 3.1.637.3.1.9.1.5.1029
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsVCDelFail 3.1.637.3.1.9.1.5.1032
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsVCAddFail 3.1.637.3.1.9.1.5.1033
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsVCInvalTranType 3.1.637.3.1.9.1.5.1037
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsVCAddMod 3.1.637.3.1.9.1.5.1038
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsVCDelTransFail 3.1.637.3.1.9.1.5.1039
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsVCIntErr 3.1.637.3.1.9.1.5.1040
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsFrcInvalTranType 3.1.637.3.1.9.1.5.1041
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsFrcInvalIndex 3.1.637.3.1.9.1.5.1281
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsNoMemFrcPath 3.1.637.3.1.9.1.5.1282
OBJECT IDENTIFIER    

adnUCNodeErrorsFrsIntfFrsSWFail 3.1.637.3.1.9.1.5.1536
OBJECT IDENTIFIER    

adnUCNodeErrorsIsna 3.1.637.3.1.9.1.6
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddConnDelPend 3.1.637.3.1.9.1.6.257
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddIfindexRoute1 3.1.637.3.1.9.1.6.515
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaInvDlciIcRoute 3.1.637.3.1.9.1.6.516
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaInvIpAdrIcRoute 3.1.637.3.1.9.1.6.517
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddConnDelPendRoute 3.1.637.3.1.9.1.6.518
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddRouteNoSuchObj 3.1.637.3.1.9.1.6.519
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddConfResourceUnavail1 3.1.637.3.1.9.1.6.1025
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddConfRefused1 3.1.637.3.1.9.1.6.1026
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddConfRangeErr1 3.1.637.3.1.9.1.6.1027
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddConfTableName1 3.1.637.3.1.9.1.6.1028
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddConfResourceUnavail2 3.1.637.3.1.9.1.6.1029
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddConfRefused2 3.1.637.3.1.9.1.6.1030
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddConfRangeErr2 3.1.637.3.1.9.1.6.1031
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaAddConfTableName2 3.1.637.3.1.9.1.6.1032
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaDelInvalid 3.1.637.3.1.9.1.6.2305
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaDelInvTblName 3.1.637.3.1.9.1.6.2306
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaDelConfPend1 3.1.637.3.1.9.1.6.2307
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaDelRouteInvIfindex 3.1.637.3.1.9.1.6.2561
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaDelRouteInvDlci 3.1.637.3.1.9.1.6.2562
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaDelDelPend2 3.1.637.3.1.9.1.6.2563
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaDelRouteInvIp1 3.1.637.3.1.9.1.6.2564
OBJECT IDENTIFIER    

adnUCNodeErrorsIsnaDelRouteInvIp2 3.1.637.3.1.9.1.6.2565
OBJECT IDENTIFIER    

adnUCNodeErrorsIsom 3.1.637.3.1.9.1.7
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddLineDelPend 3.1.637.3.1.9.1.7.257
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddConnDelPend 3.1.637.3.1.9.1.7.513
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddIfindexTrp1 3.1.637.3.1.9.1.7.769
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomInvDlciIcTrp 3.1.637.3.1.9.1.7.770
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddConnDelPendTrp 3.1.637.3.1.9.1.7.772
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddIfindexTrp2 3.1.637.3.1.9.1.7.773
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddTrpNoSuchObj 3.1.637.3.1.9.1.7.774
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddConfRefused1 3.1.637.3.1.9.1.7.1025
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddConfRangeErr1 3.1.637.3.1.9.1.7.1026
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddConfTableName1 3.1.637.3.1.9.1.7.1028
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddConfRefused2 3.1.637.3.1.9.1.7.1029
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddConfRangeErr2 3.1.637.3.1.9.1.7.1030
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddConfTableName2 3.1.637.3.1.9.1.7.1032
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddConfResourceUnavail1 3.1.637.3.1.9.1.7.1033
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomAddConfResourceUnavail2 3.1.637.3.1.9.1.7.1034
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomDelInvalid 3.1.637.3.1.9.1.7.2305
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomDelInvTblName 3.1.637.3.1.9.1.7.2306
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomDelConfPend1 3.1.637.3.1.9.1.7.2307
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomDelDelPend2 3.1.637.3.1.9.1.7.2563
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomDelTrapInvIfindex 3.1.637.3.1.9.1.7.2561
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomDelTrapInvDlci 3.1.637.3.1.9.1.7.2562
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomDelTrapInvIp1 3.1.637.3.1.9.1.7.2564
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomDelTrapInvIp2 3.1.637.3.1.9.1.7.2565
OBJECT IDENTIFIER    

adnUCNodeErrorsIsomDelLineInvState 3.1.637.3.1.9.1.7.2817
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSi 3.1.637.3.1.9.1.10
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSiLength2Big 3.1.637.3.1.9.1.10.5
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSiNoMalloc 3.1.637.3.1.9.1.10.6
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSiAddr2Long 3.1.637.3.1.9.1.10.7
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSiBadType 3.1.637.3.1.9.1.10.8
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSiCreateFail 3.1.637.3.1.9.1.10.258
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSiGetTransFail 3.1.637.3.1.9.1.10.260
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSiUpdateFail 3.1.637.3.1.9.1.10.266
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSiUpdateWoCreate 3.1.637.3.1.9.1.10.268
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSiIntfInternalErr 3.1.637.3.1.9.1.10.269
OBJECT IDENTIFIER    

adnUCNodeErrorsFraSiNoConfigUpdate 3.1.637.3.1.9.1.10.304
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlip 3.1.637.3.1.9.1.12
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipGeneral 3.1.637.3.1.9.1.12.1
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipIfIndex 3.1.637.3.1.9.1.12.2
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipValue 3.1.637.3.1.9.1.12.3
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipTableFormat 3.1.637.3.1.9.1.12.4
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipConfig 3.1.637.3.1.9.1.12.5
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipGet 3.1.637.3.1.9.1.12.6
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipGetFirst 3.1.637.3.1.9.1.12.7
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipGetNext 3.1.637.3.1.9.1.12.8
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipSet 3.1.637.3.1.9.1.12.9
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipUpdate 3.1.637.3.1.9.1.12.10
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipTest 3.1.637.3.1.9.1.12.11
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipUpdateFailed 3.1.637.3.1.9.1.12.12
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipGetTransFailed 3.1.637.3.1.9.1.12.13
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrFlipCreateLcbFailed 3.1.637.3.1.9.1.12.14
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuicc 3.1.637.3.1.9.1.13
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccGeneral 3.1.637.3.1.9.1.13.1
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccIfIndex 3.1.637.3.1.9.1.13.2
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccValue 3.1.637.3.1.9.1.13.3
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccTableFormat 3.1.637.3.1.9.1.13.4
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccConfig 3.1.637.3.1.9.1.13.5
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccGet 3.1.637.3.1.9.1.13.6
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccGetFirst 3.1.637.3.1.9.1.13.7
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccGetNext 3.1.637.3.1.9.1.13.8
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccSet 3.1.637.3.1.9.1.13.9
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccUpdate 3.1.637.3.1.9.1.13.10
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccTest 3.1.637.3.1.9.1.13.11
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccUpdateFailed 3.1.637.3.1.9.1.13.12
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccNoMoreRoomForIfIndex 3.1.637.3.1.9.1.13.13
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrQuiccGetTransFailed 3.1.637.3.1.9.1.13.14
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrSpyd 3.1.637.3.1.9.1.14
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrSpydNoMemory 3.1.637.3.1.9.1.14.1
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrSpydInvVal 3.1.637.3.1.9.1.14.2
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrSpydFracInvVal 3.1.637.3.1.9.1.14.3
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrSpydFrac2 3.1.637.3.1.9.1.14.4
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrSpydDownLoad 3.1.637.3.1.9.1.14.5
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrSpydNoCB 3.1.637.3.1.9.1.14.6
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrSpydifAdmin 3.1.637.3.1.9.1.14.7
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrSpydConfig 3.1.637.3.1.9.1.14.8
OBJECT IDENTIFIER    

adnUCNodeErrorsLdrSpydTransID 3.1.637.3.1.9.1.14.9
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmline 3.1.637.3.1.9.1.18
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineIncTranId 3.1.637.3.1.9.1.18.1
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineIncTranType 3.1.637.3.1.9.1.18.2
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineNotUpdPar 3.1.637.3.1.9.1.18.12
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineIncParVal 3.1.637.3.1.9.1.18.13
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineMissingPar 3.1.637.3.1.9.1.18.14
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineBoardNotCre 3.1.637.3.1.9.1.18.20
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineLineAlCre 3.1.637.3.1.9.1.18.21
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineIncBoardType 3.1.637.3.1.9.1.18.22
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineSpareBoard 3.1.637.3.1.9.1.18.23
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineLineNotCre 3.1.637.3.1.9.1.18.24
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineTimNotSup 3.1.637.3.1.9.1.18.25
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineTimNcpLoop 3.1.637.3.1.9.1.18.26
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineIncApplType 3.1.637.3.1.9.1.18.27
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineIfTabNotDel 3.1.637.3.1.9.1.18.30
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineNotCigPar 3.1.637.3.1.9.1.18.100
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineNotAtmTcPar 3.1.637.3.1.9.1.18.110
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineNoLowIndex 3.1.637.3.1.9.1.18.111
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineNoAtmIfap 3.1.637.3.1.9.1.18.112
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineNotDs3E3Par 3.1.637.3.1.9.1.18.120
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineNotT1E1Par 3.1.637.3.1.9.1.18.130
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineNotSonetPar 3.1.637.3.1.9.1.18.140
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineNotRs232Par 3.1.637.3.1.9.1.18.150
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmlineInOutSpeed 3.1.637.3.1.9.1.18.151
OBJECT IDENTIFIER    

adnUCNodeErrorsAafd 3.1.637.3.1.9.1.19
OBJECT IDENTIFIER    

adnUCNodeErrorsAafdMissingNominator 3.1.637.3.1.9.1.19.1
OBJECT IDENTIFIER    

adnUCNodeErrorsAafdMibError 3.1.637.3.1.9.1.19.2
OBJECT IDENTIFIER    

adnUCNodeErrorsAafdFmtError 3.1.637.3.1.9.1.19.3
OBJECT IDENTIFIER    

adnUCNodeErrorsAafdConfig 3.1.637.3.1.9.1.19.4
OBJECT IDENTIFIER    

adnUCNodeErrorsAafdInconsTran 3.1.637.3.1.9.1.19.5
OBJECT IDENTIFIER    

adnUCNodeErrorsAafdTimerFail 3.1.637.3.1.9.1.19.6
OBJECT IDENTIFIER    

adnUCNodeErrorsAafdCtxFail 3.1.637.3.1.9.1.19.7
OBJECT IDENTIFIER    

adnUCNodeErrorsAafdACI2TFull 3.1.637.3.1.9.1.19.8
OBJECT IDENTIFIER    

adnUCNodeErrorsAafdInconsState 3.1.637.3.1.9.1.19.9
OBJECT IDENTIFIER    

adnUCNodeErrorsAafdDoneError 3.1.637.3.1.9.1.19.10
OBJECT IDENTIFIER    

adnUCNodeErrorsPmd 3.1.637.3.1.9.1.20
OBJECT IDENTIFIER    

adnUCNodeErrorsPmdInconsTran 3.1.637.3.1.9.1.20.1
OBJECT IDENTIFIER    

adnUCNodeErrorsPmdInconsIndex 3.1.637.3.1.9.1.20.2
OBJECT IDENTIFIER    

adnUCNodeErrorsPmdDatagramSend 3.1.637.3.1.9.1.20.6
OBJECT IDENTIFIER    

adnUCNodeErrorsPmdConvIndex 3.1.637.3.1.9.1.20.32
OBJECT IDENTIFIER    

adnUCNodeErrorsPmdMaxDefer 3.1.637.3.1.9.1.20.35
OBJECT IDENTIFIER    

adnUCNodeErrorsAsig 3.1.637.3.1.9.1.21
OBJECT IDENTIFIER    

adnUCNodeErrorsAsigObjectMaxNb 3.1.637.3.1.9.1.21.1
OBJECT IDENTIFIER    

adnUCNodeErrorsAsigVpiVccMaxNb 3.1.637.3.1.9.1.21.2
OBJECT IDENTIFIER    

adnUCNodeErrorsAsigNoBandwith 3.1.637.3.1.9.1.21.3
OBJECT IDENTIFIER    

adnUCNodeErrorsAsigMaxVccNb 3.1.637.3.1.9.1.21.4
OBJECT IDENTIFIER    

adnUCNodeErrorsAsigMaxVpcNb 3.1.637.3.1.9.1.21.5
OBJECT IDENTIFIER    

adnUCNodeErrorsAsigCDVTooLarge 3.1.637.3.1.9.1.21.6
OBJECT IDENTIFIER    

adnUCNodeErrorsAsigAddrMaxNb 3.1.637.3.1.9.1.21.7
OBJECT IDENTIFIER    

adnUCNodeErrorsAsigNMSRequest 3.1.637.3.1.9.1.21.101
OBJECT IDENTIFIER    

adnUCNodeErrorsAsigSoftware 3.1.637.3.1.9.1.21.102
OBJECT IDENTIFIER    

adnUCNodeErrorsAsigNoMemory 3.1.637.3.1.9.1.21.103
OBJECT IDENTIFIER    

adnAtmTCTable 3.1.637.3.1.4.37.1.50
The ADN Transmission Convergence (TC) extension table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmTCEntry

adnAtmTCEntry 3.1.637.3.1.4.37.1.50.1
An entry in the ADN Transmission Convergence (TC) extension table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmTCEntry  

adnAtmTCAlarmState 3.1.637.3.1.4.37.1.50.1.1
This variable indicates the state of alarms of the Transmission and Convergence part of ATM layer. It includes information given by atmTCAlarmState. It is a bit map represented as a sum; therefore, it can represent multiple defects simultaneously. The adnAtmTCNoAlarm bit should be set only if no other bit is set. The bit positions and their corresponding ATM core counter numbers # are: # Bit Value ------------------------------------------------------ . 1 adnAtmTCNoAlarm . No alarm present 17 2 adnAtmTCCorrectedHec . Excessive number of cells corrected . through Header Error Control (HEC) 18 4 adnAtmTCUncorrectedHec . Excessive number of cells deleted . through Header Error Control (HEC) 22 8 adnAtmTCUpwardOverflow . Upwards cell buffer overflow 26 16 adnAtmTCDownwardOverflow . Downwards cell buffer overflow 25 32 adnAtmTCLossOfAtmSignalCounter . Loss of ATM signal from the ET part . to the LT part of the board
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTCScramblerConfig 3.1.637.3.1.4.37.1.50.1.2
Defines if ATM scrambler is active or not.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER adnAtmTCScramblerOn(1), adnAtmTCScramblerOff(2)  

adnAtmTCCellRateDecConfig 3.1.637.3.1.4.37.1.50.1.3
The type of cell rate decoupling (CRD) mode selected for the ATM TC layer: - unassigned cells (ANSI), - idle cells (ITU), - no CRD for an ATM TC layer over an ATM internal line. Common Name: Cell Rate Decoupling
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER adnAtmTCUnassignedCell(1), adnAtmTCIdleCell(2), adnAtmTCNoCRD(3)  

adnAtmTCMappingConfig 3.1.637.3.1.4.37.1.50.1.4
The type of mapping of ATM layer on physical layer: - other mapping : the mapping of the ATM layer is none of the following mappings, - PLCP mapping : the ATM layer is mapped on Physical Layer Convergence Protocol layer (PLCP), - direct mapping : the ATM layer is directly mapped on transmission layer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER adnAtmTCOtherMapping(1), adnAtmTCPlcpMapping(2), adnAtmTCDirectMapping(3)  

adnAtmTCLossOfCellDelCounter 3.1.637.3.1.4.37.1.50.1.5
Duration of loss-of-cell-delineation (LOCD). Counter #16 of the ATM core, only available on ATM-SONET, ATM-SDH, ATM-DS3-DM, ATM-E3, ATM-T1 and ATM-E1 interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmTCCorrectedHecCounter 3.1.637.3.1.4.37.1.50.1.6
Number of cells corrected through Header Error Control (HEC) mechanisms. Counter #17 of the ATM core, only available on ATM interfaces over lines on BBTP3C, BBE3B, BBE3B3, BBS1B, BBS1B3, BBS1B2, BBS1B4, BBS4B or BBS4B2 board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmTCUncorrectedHecCounter 3.1.637.3.1.4.37.1.50.1.7
Number of cells discarded through Header Error Control (HEC) mechanisms. Counter #18 of the ATM core, only available on ATM-SONET, ATM-SDH, ATM-DS3, ATM-E3, ATM-T1 and ATM-E1 interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmTCUpwardOverflowCounter 3.1.637.3.1.4.37.1.50.1.8
Number of upward cell buffer (output buffer) overflow events. Counter #22 of the ATM core, only available on ATM interfaces over lines on BBT1B, BBE1B, BBE3B, BBE3B3, BBT3B, BBT3B2, BBT3B3, BBT3B4, BBS1B, BBS1B3, BBS1B2, BBS1B4, BBS4B or BBS4B2 board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmTCDownwardOverflowCounter 3.1.637.3.1.4.37.1.50.1.9
Number of downward cell buffer (input buffer) overflow events. Counter #26 of the ATM core, only available on ATM-SONET, ATM-SDH, ATM-DS3, and ATM-E3 interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmTCLossOfAtmSignalCounter 3.1.637.3.1.4.37.1.50.1.10
Duration of loss of ATM signal from the Exchange Termination processor (ET) to the Line Termination processor (LT). Counter #31 of the ATM core, only available on ATM interfaces over lines on BBS1B, BBS1B3, BBS1B2, or BBS1B4 board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmDs3PlcpTable 3.1.637.3.1.4.37.1.51
The ADN DS3 Physical Layer Convergence Protocol (PLCP) extension table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmDs3PlcpEntry

adnAtmDs3PlcpEntry 3.1.637.3.1.4.37.1.51.1
An entry in the ADN DS3 Physical Layer Convergence Protocol (PLCP) extension table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmDs3PlcpEntry  

adnAtmDs3PlcpFerfCounter 3.1.637.3.1.4.37.1.51.1.1
Duration of far end received failure (FERF) received from the remote equipment. FERF is also called remote alarm indication (RAI) or received yellow alarm. Counter #10 of the ATM core, only available on DS3-PLCP interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmDs3PlcpLofCounter 3.1.637.3.1.4.37.1.51.1.2
Duration of loss-of-frame (LOF). Counter #12 of the ATM core, only available on DS3-PLCP interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmDs3PlcpFebeCounter 3.1.637.3.1.4.37.1.51.1.3
Number of far end block errors (FEBE) received from the remote equipment. Counter #9 of the ATM core, only available on DS3-PLCP interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmDs3PlcpBip8Counter 3.1.637.3.1.4.37.1.51.1.4
Number of 8-bits interleaved parity (BiP-8) errors. received from the remote equipment. Counter #11 of the ATM core, only available on DS3-PLCP interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmDs3PlcpOofCounter 3.1.637.3.1.4.37.1.51.1.5
Number of out-of-frame (OOF) events. Counter #20 of the ATM core, only available on DS3-PLCP interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErCounterTable 3.1.637.3.1.5.15.21
This table is the ATM boards error counter table. Each counter corresponds to a defect number identified by a bit set in the adnProcessorStatus of the adnProcessorTable. The counters are classified according to the board type. Some are specific to the broadband ATM switching element (BBASE) board also called the matrix board.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmBoardErCounterEntry

adnAtmBoardErCounterEntry 3.1.637.3.1.5.15.21.1
An entry in the ATM boards error counter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmBoardErCounterEntry  

adnAtmBoardErOrWgStatus 3.1.637.3.1.5.15.21.1.1
This variable indicates the gravity of a processor failure. It is a bit map represented as a sum. Each bit position maps to the corresponding position in the nominator adnASEBoardStatus, adnCIGBoardStatus or adnHSCBoardStatus (which defines the processor's failure status). The adnAtmBoardErOrWgStatus bit classifies the failure as either an error (value '1') or a warning (value '0'). A bit value of '0' can also mean the failure classification does not apply to the failure status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmBoardASEStatus 3.1.637.3.1.5.15.21.1.2
This variable indicates the processor status. It is a bit map represented as a sum; therefore it can represent multiple failures. This variable is only significant for the matrix boards. The bit positions are : 16384 : adnAtmBoardErQRP0RAMP BGQRP-0 chip RAM parity error 65536 : adnAtmBoardErQRP0FIFO BGQRP-0 chip extraction FIFO overflow 131072 : adnAtmBoardErQRP1RAMP BGQRP-1 chip RAM parity error 524288 : adnAtmBoardERQRP1FIFO BGQRP-1 chip extraction FIFO overflow 1048576 : adnAtmBoardErQRP2RAMP BGQRP-2 chip RAM parity error 4194304 : adnAtmBoardErQRP2FIFO BGQRP-2 chip extraction FIFO overflow 8388608 : adnAtmBoardErQRP3RAMP BGQRP-3 chip RAM parity error 33554432 : adnAtmBoardErQRP3FIFO BGQRP-3 chip extraction FIFO overflow 67108864 : adnAtmBoardErHMPLLPC loss of low priority cells 134217728 : adnAtmBoardErHMPLHPC loss of high priority cells 268435456 : adnAtmBoardErHMP0SYNC BGHMP-0 chip synchronization fault 2147483648: adnAtmBoardErHMP1SYNC BGHMP-1 chip synchronization fault N.B.: This variable is significant when the operational state of the processor is enabled. When there is no processor error, this variable has the value 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmBoardCIGStatus 3.1.637.3.1.5.15.21.1.3
This variable indicates the processor status. It is a bit map represented as a sum; therefore it can represent multiple failures. This variable is only significant for CIG boards. The bit positions are : 1 : adnAtmBoardErUFOF user FIFO overflow 2 : adnAtmBoardErUFRF user FIFO read failure 4 : adnAtmBoardErNFOF network FIFO overflow 8 : adnAtmBoardErPHTRAMP BGPHT chip RAM parity error 16 : adnAtmBoardErNFRF network FIFO read failure 128 : adnAtmBoardErRBOF receipt cell buffer overflow 4096 : adnAtmBoardErAPPLIQ applique not present N.B.: This variable is significant when the operational state of the processor is enabled. When there is no processor error, this variable has the value 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmBoardHSCStatus 3.1.637.3.1.5.15.21.1.4
This variable indicates the processor status.It is a bit map represented as a sum; therefore it can represent multiple failures. This variable is only significant for HSC boards, except CEM8 boards. For all HSC boards except BBTS1C and BBTP3C boards, the bit positions are : 1 : adnAtmBoardErUFOF user FIFO overflow 2 : adnAtmBoardErUFRF user FIFO read failure 4 : adnAtmBoardErNFOF network FIFO overflow 8 : adnAtmBoardErPHTRAMP BGPHT chip RAM parity error 16 : adnAtmBoardErNFRF network FIFO read failure 128 : adnAtmBoardErRBOF receipt cell buffer overflow 512 : adnAtmBoardErLIRC0 loss of signal on IRC0 1024 : adnAtmBoardErLIRC1 loss of signal on IRC1 4096 : adnAtmBoardErAPPLIQ applique not present For the BBE1B and BBT1B boards, there are specific defects corresponding to the following bit positions : 8192 : adnAtmBoardErFIFO rate reduction FIFO overflow 16384 : adnAtmBoardErFIFC rate reduction FIFO cell alignment failure 32768 : adnAtmBoardErBGETB loss of cell synchronization 65536 : adnAtmBoardErBGETB upwards start of cell error in BGMUX(or BGMUX 2) For the BBTS1C and BBTP3C boards,the bit positions are : 1 : adnAtmBoardErPHT0FIF0 FIFO defect on PHT2-0 2 : adnAtmBoardErPHT0FIF1 FIFO defect on PHT2-1 4 : adnAtmBoardErPHT0FIF2 FIFO defect on PHT2-2 8 : adnAtmBoardErPHT0FIF3 FIFO defect on PHT2-3 512 : adnAtmBoardErLIRC0 loss of signal on IRC0 1024 : adnAtmBoardErLIRC1 loss of signal on IRC1 4096 : adnAtmBoardErAPPLIQ applique not present 8192 : adnAtmBoardErUFOF user side FIFO overflow 16384 : adnAtmBoardErUFE user side FIFO error 32768 : adnAtmBoardErEFOV extraction FIFO overflow 65636 : adnAtmBoardErQRPPRAMP QRP RAM parity error 131072 : adnAtmBoardErDRAME DRAM ECC error 262144 : adnAtmBoardErDCSE downwards cell syncho error 524288 : adnAtmBoardErDRFOV downwards receiving FIFO overflow 1048576 : adnAtmBoardErRFORRF rate reduction FIFO overflow 2097152 : adnAtmBoardErDCMOV downwards cell memory overflows 4194304 : adnAtmBoardErDCMME downwards cell memory management error 8388608 : adnAtmBoardErUCSE upwards cell synchro error 16777216 : adnAtmBoardErURFOV upwards receiving FIFO overflow 33554432 : adnAtmBoardErUCMOV upwards cell memory overflow 67108864 : adnAtmBoardErUCMME upwards cell memory management error 1342177728: adnAtmBoardErULMA0OV upwards LMA0 overflow N.B.: This variable is significant when the operational state of the processor is enabled. When there is no processor error, this variable has the value 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmBoardErQRP0RAMPCounter 3.1.637.3.1.5.15.21.1.5
The counter associated with the number of the first QRP chip RAM parity errors; counter #14 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErQRP0FIFOCounter 3.1.637.3.1.5.15.21.1.6
The counter associated with the number of the first QRP chip extraction FIFO overflows; counter #16 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErQRP1RAMPCounter 3.1.637.3.1.5.15.21.1.7
The counter associated with the number of the second QRD chip RAM parity errors; counter #17 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErQRP1FIFOCounter 3.1.637.3.1.5.15.21.1.8
The counter associated with the number of the first QRP chip extraction FIFO overflows; counter #19 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErQRP2RAMPCounter 3.1.637.3.1.5.15.21.1.9
The counter associated with the number of the second QRP chip RAM parity errors; counter #20 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErQRP2FIFOCounter 3.1.637.3.1.5.15.21.1.10
The counter associated with the number of the second QRP chip extraction FIFO overflows; counter #22 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErQRP3RAMPCounter 3.1.637.3.1.5.15.21.1.11
The counter associated with the number of the third QRP chip RAM parity errors; counter #23 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErQRP3FIFOCounter 3.1.637.3.1.5.15.21.1.12
The counter associated with the number of the third QRP chip extraction FIFO overflows; counter #25 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErHMPLLPCCounter 3.1.637.3.1.5.15.21.1.13
The counter associated with the number of low priority cells lost due to Selective Cell Discard (SCD); counter #26 of the ATM core; this counter is only relevant for the matrix board.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErHMPLHPCCounter 3.1.637.3.1.5.15.21.1.14
The counter associated with the number of high priority cells lost due to buffer overflow (FULC); counter #27 of the ATM core; this counter is only relevant for the matrix board.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErHMP0SYNCCounter 3.1.637.3.1.5.15.21.1.15
The counter associated with the number of fault synchronization in the first HMP chip; counter #28 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErHMP1SYNCCounter 3.1.637.3.1.5.15.21.1.16
The counter associated with the number of fault synchronization in the second HMP chip; counter #31 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErUFOFCounter 3.1.637.3.1.5.15.21.1.17
The counter associated with the number of user FIFO overflows; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErUFRFCounter 3.1.637.3.1.5.15.21.1.18
The counter associated with the number of user FIFO read failures; counter #1 of the ATM core; this counter is not relevant for the matrix board, for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErNFOFCounter 3.1.637.3.1.5.15.21.1.19
The counter associated with the number of network FIFO overflows; counter #2 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErPHTRAMPCounter 3.1.637.3.1.5.15.21.1.20
The counter associated with the number of BGPHT chip RAM parity errors; counter #3 of the ATM core; this counter is not relevant for the matrix board, the HBCEx boards, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErNFRFCounter 3.1.637.3.1.5.15.21.1.21
The counter associated with the number of network FIFO read failures; counter #4 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErNAVCCounter 3.1.637.3.1.5.15.21.1.22
The counter associated with the number of cells received on non active VC; counter #5 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErNAVPCounter 3.1.637.3.1.5.15.21.1.23
The counter associated with the number of cells received on non active VP; counter #6 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErRBOFCounter 3.1.637.3.1.5.15.21.1.24
The counter associated with the number of reception buffer overflows; counter #7 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErAPPLIQCounter 3.1.637.3.1.5.15.21.1.25
The counter associated with the duration of applique missing. expressed in milliseconds; counter #12 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErLIRC0Counter 3.1.637.3.1.5.15.21.1.26
The counter associated with the number of loss of signal on IRC0; counter #9 of the ATM core; this counter is only relevant for a HSC board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErLIRC1Counter 3.1.637.3.1.5.15.21.1.27
The counter associated with the duration of loss of signal on IRC1. expressed in milliseconds; counter #10 of the ATM core; this counter is only relevant for a HSC board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErRFIFOCounter 3.1.637.3.1.5.15.21.1.28
The counter associated with the duration of rate reduction FIFO overflows (from ET to LT). expressed in milliseconds; counter #13 of the ATM core; this counter is only relevant for BBE1B and BBT1B boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErRFIFCCounter 3.1.637.3.1.5.15.21.1.29
The counter associated with the number of rate reduction FIFO cell alignment failures; counter #14 of the ATM core; this counter is only relevant for BBE1B and BBT1B boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErBGETBCounter 3.1.637.3.1.5.15.21.1.30
The counter associated with the number of loss of cell synchronization (BGETB); counter #15 of the ATM core; this counter is only relevant for BBE1B and BBT1B boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErBGMUXCounter 3.1.637.3.1.5.15.21.1.31
The counter associated with the number of received start of cell errors from BGMUX; counter #16 of the ATM core; this counter is only relevant for BBE1B and BBT1B boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErHOBCounter 3.1.637.3.1.5.15.21.1.32
The counter associated with the duration of overflows on high priority output buffer; this counter is not relevant for HSC boards without a high priority output buffer. expressed in milliseconds; counter #18 of the ATM core.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErMOBCounter 3.1.637.3.1.5.15.21.1.33
The counter associated with the duration of overflows on medium priority output buffer; this counter is not relevant for HSC boards without a medium priority output buffer (e.g. BBT1B and BBE1B); expressed in milliseconds; counter #19 of the ATM core.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErLOBCounter 3.1.637.3.1.5.15.21.1.34
The counter associated with the duration of overflows on low priority output buffer; this counter is not relevant for HSC boards without a low priority output buffer; expressed in milliseconds; counter #20 of the ATM core.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErDRAMPCounter 3.1.637.3.1.5.15.21.1.35
The counter associated with the number of processor DRAM parity errors; counter #17 of the ATM core; this counter is only relevant for a HBCEx board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErRFIFFCounter 3.1.637.3.1.5.15.21.1.36
The counter associated with the number of Rate reduction FIFO full events from ET to AAL1 component; counter #31 of the ATM core; this counter is only relevant for a HBCEx board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardCEMStatus 3.1.637.3.1.5.15.21.1.37
This variable indicates the processor status. It is a bit map represented as a sum; therefore it can represent multiple failures. This variable is only significant for CEM8 boards. The bit positions are : 1 : adnAtmBoardErUFOF user FIFO overflow 2 : adnAtmBoardErUFRF user FIFO read failure 4 : adnAtmBoardErNFOF network FIFO overflow 16 : adnAtmBoardErNFRF network FIFO read failure 512 : adnAtmBoardErLIRC0 loss of signal on IRC0 1024 : adnAtmBoardErLIRC1 loss of signal on IRC1 4096 : adnAtmBoardErAPPLIQ applique not present 131072 : adnAtmBoardErDRAMP processor DRAM parity error 2147483648: adnAtmBoardErRFIFF rate reduction FIFO full from ET to AAL1 component N.B.: This variable is significant when the operational state of the port is enabled. When there is no port error, this variable has the value 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmBoardErDCSECounter 3.1.637.3.1.5.15.21.1.38
The counter associated with the number of downwards cell synchro errors; counter #18 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErDRFOVCounter 3.1.637.3.1.5.15.21.1.39
The counter associated with the number of downwards receiving FIFO overflows; counter #19 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErDCMOVCounter 3.1.637.3.1.5.15.21.1.40
The counter associated with the number of downwards cell memory overflows; counter #21 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErDCMMECounter 3.1.637.3.1.5.15.21.1.41
The counter associated with the number of downwards cell memory management errors; counter #22 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErUCSECounter 3.1.637.3.1.5.15.21.1.42
The counter associated with the number of upwards cell synchro errors; counter #23 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErURFOVCounter 3.1.637.3.1.5.15.21.1.43
The counter associated with the number of upwards receiving FIFO overflows; counter #24 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErUCMOVCounter 3.1.637.3.1.5.15.21.1.44
The counter associated with the number of upwards cell memory overflows; counter #25 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErUCMMECounter 3.1.637.3.1.5.15.21.1.45
The counter associated with the number of upwards cell memory management errors; counter #26 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErRFORRF0Counter 3.1.637.3.1.5.15.21.1.46
The counter associated with the number of rate reduction FIFO overflows on RRF0; counter #32 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErRFORRF1Counter 3.1.637.3.1.5.15.21.1.47
The counter associated with the number of rate reduction FIFO overflows on RRF1; counter #33 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardErRFORRF2Counter 3.1.637.3.1.5.15.21.1.48
The counter associated with the number of rate reduction FIFO overflows on RRF2; counter #34 of the ATM core; this counter is only relevant for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraCounterTable 3.1.637.3.1.5.15.22
This table is the ATM boards traffic counter table. The counter is classified according to the board type.It is specific to the broadband ATM switching element (BBASE) board also called the matrix board.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmBoardTraCounterEntry

adnAtmBoardTraCounterEntry 3.1.637.3.1.5.15.22.1
An entry in the ATM boards traffic counter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmBoardTraCounterEntry  

adnAtmBoardTraHMP0ObsCounter 3.1.637.3.1.5.15.22.1.1
The counter associated with the number of cells received since the observation threshold is exceeded in the first HMP chip; counter #0 of the ATM core; this counter is only relevant for the matrix board with a HMP release 2 chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraHMP1ObsCounter 3.1.637.3.1.5.15.22.1.2
The counter associated with the number of cells received since the observation threshold is exceeded in the second HMP chip; counter #1 of the ATM core; this counter is only relevant for the matrix board with a HMP release 2 chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraFPTMICICounter 3.1.637.3.1.5.15.22.1.3
The counter associated with the number of free outgoing point-to-multipoint (PTM) internal channel identifiers (ICI); counter #2 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnAtmBoardTraMOBSCDCounter 3.1.637.3.1.5.15.22.1.4
The counter associated with the number of Selective Cell Discard (SCD) activations on medium priority output buffer; counter #33 of the ATM core; this counter is only relevant for a HSC board with BGTOB chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraLOBSCDCounter 3.1.637.3.1.5.15.22.1.5
The counter associated with the number of Selective Cell Discard (SCD) activations on low priority output buffer; counter #34 of the ATM core; this counter is only relevant for a HSC board with BGTOB chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraMOBEFCICounter 3.1.637.3.1.5.15.22.1.6
The counter associated with the number of Explicit Forward Congestion Indication (EFCI) activations on medium priority output buffer; counter #35 of the ATM core; this counter is only relevant for a HSC board with BGTOB chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraLOBEFCICounter 3.1.637.3.1.5.15.22.1.7
The counter associated with the number of Explicit Forward Congestion Indication (EFCI) activations on low priority output buffer; counter #36 of the ATM core; this counter is only relevant for a HSC board with BGTOB chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraMOBTPDCounter 3.1.637.3.1.5.15.22.1.8
The counter associated with the number of Tail Packet Discard (TPD) activations on medium priority output buffer; counter #37 of the ATM core; this counter isis only relevant for a HSC board with BGTOB chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraLOBTPDCounter 3.1.637.3.1.5.15.22.1.9
The counter associated with the number of Tail Packet Discard (TPD) activations on low priority outpur buffer; counter #38 of the ATM core; this counter is only relevant for a HSC board with BGTOB chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraHOBObsCounter 3.1.637.3.1.5.15.22.1.10
The counter associated with the number of observation threshold exceedings on high priority output buffer; counter #39 of the ATM core; this counter is only relevant for a HSC board with BGTOB chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraMOBObsCounter 3.1.637.3.1.5.15.22.1.11
The counter associated with the number of observation threshold exceedings on medium priority output buffer; counter #40 of the ATM core; this counter is only relevant for a HSC board with BGTOB chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmBoardTraLOBObsCounter 3.1.637.3.1.5.15.22.1.12
The counter associated with the number of observation threshold exceedings on low priority output buffer; counter #41 of the ATM core; this counter is only relevant for a HSC board with BGTOB chip.
Status: deprecated Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErCounterTable 3.1.637.3.1.5.15.23
This table is the ATM electrical interface (AEI) port error counter table. Each counter corresponds to a defect number identified by a bit set in the adnAeiPortEratus of the adnAeiPortTable. The counters are classified according to the board type. Some are specific to the broadband ATM switching element (BBASE) board also called the matrix board.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAeiPortErCounterEntry

adnAeiPortErCounterEntry 3.1.637.3.1.5.15.23.1
An entry in the ATM electrical interface (AEI) port error counter table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAeiPortErCounterEntry  

adnAeiPortErOrWgStatus 3.1.637.3.1.5.15.23.1.1
This variable indicates the gravity of a port failure. It is a bit map represented as a sum. Each bit position maps to the corresponding position in the nominator adnAeiPortASEStatus, adnAeiPortCIGStatus or adnAeiPortHSCStatus (which defines the port's failure status). The adnAeiPortErOrWgStatus bit classifies the failure as either an error (value '1') or a warning (value '0'). A bit value of '0' can also mean the failure classification does not apply to the failure status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAeiPortASEStatus 3.1.637.3.1.5.15.23.1.2
This variable indicates the port status. It is a bit map represented as a sum; therefore it can represent multiple failures. This variable is only significant for ASE boards. The bit positions are : 1 : adnAeiPortOOS synchronization fault ATM Electrical Interface 2 : adnAeiPortLOS synchronization fault 8 bit parallel Atm Internal Interface 4 : adnAeiPortNFOF network FIFO overflows 16 : adnAeiPortCECH corrected errors in cell header 32 : adnAeiPortUCECH uncorrected errors in cell header 256 : adnAeiPortNPE parity errors on payload 512 : adnAeiPortRTA routing data error status 4096 : adnAeiPortNMA1 no active maintenance cell received 16384 : adnAeiPortEMA1 error active maintenance cell received 67108864 : adnAeiPortNCRC CRC errors detected on payload field 134217728 : adnAeiPortNAAL AAL (ATM Adaptation Layer) sequence error in AEI reception 1073741824: adnAeiPortURC unrouted cells N.B.: This variable is significant when the operational state of the port is enabled. When there is no port error, this variable has the value 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAeiPortCIGStatus 3.1.637.3.1.5.15.23.1.3
This variable indicates the port status. It is a bit map represented as a sum; therefore it can represent multiple failures. This variable is only significant for CIG boards. The bit positions are : 1 : adnAeiPortOOS out-of-synchronization 4 : adnAeiPortNFOF network FIFO overflows 8 : adnAeiPortIEMRAMP BGIEM chip RAM parity errors 16 : adnAeiPortCECH corrected errors in cell header 32 : adnAeiPortUCECH uncorrected errors in cell header 64 : adnAeiPortCRCMA CRC errors on payload field of MA1 (Active Maintenance type 1) cells 128 : adnAeiPortCRCSIC CRC errors on payload field of SIC (Self Identified Cell) cells 256 : adnAeiPortNPE parity errors on payload 4096 : adnAeiPortNMA1 no active maintenance cell received 16384 : adnAeiPortEMA1 active maintenance cell received with error indication 131072 : adnAeiPortNSFOF network signalling FIFO overflow 262144 : adnAeiPortNFWF network FIFO write failure 524288 : adnAeiPortSFWF signalling FIFO write failure 1048576 : adnAeiPortNSFRF network signalling FIFO read failure 4194304 : adnAeiPortUSFRF user signalling FIFO read failure 8388608 : adnAeiPortUFWF user FIFO write failure 16777216 : adnAeiPortUSFOF user signalling FIFO overflow 33554432 : adnAeiPortNICI cells received on non-active ICI (Internal Communication Interface) 67108864 : adnAeiPortNCRC CRC errors detected on network side 134217728 : adnAeiPortNAAL AAL (ATM Adaptation Layer) sequence error on network side 268435456 : adnAeiPortUCRC CRC errors detected on user side 536870912 : adnAeiPortUAAL AAL sequence error on user side 2147483648: adnAeiPortSFIFO load sharing FIFO overflow N.B.: This variable is significant when the operational state of the port is enabled. When there is no port error, this variable has the value 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAeiPortHSCStatus 3.1.637.3.1.5.15.23.1.4
This variable indicates the port status. It is a bit map represented as a sum; therefore it can represent multiple failures. This variable is only significant for HSC boards (except CEM8 boards). For HSC boards except BBTS1C and BBTP3C boards, the bit positions are : 1 : adnAeiPortOOS out-of-synchronization 4 : adnAeiPortNFOF network FIFO overflows 8 : adnAeiPortIEMRAMP BGIEM chip RAM parity errors 16 : adnAeiPortCECH corrected errors in cell header 32 : adnAeiPortUCECH uncorrected errors in cell header 64 : adnAeiPortCRCMA CRC errors on payload field of MA1 (Active Maintenance type 1) cells 128 : adnAeiPortCRCSIC CRC errors on payload field of SIC (Self Identified Cell) cells 256 : adnAeiPortNPE parity errors on payload 4096 : adnAeiPortNMA1 no active maintenance cell received 16384 : adnAeiPortEMA1 active maintenance cell received with error indication 131072 : adnAeiPortNSFOF network signalling FIFO overflow 262144 : adnAeiPortNFWF network FIFO write failure 524288 : adnAeiPortSFWF signalling FIFO write failure 1048576 : adnAeiPortNSFRF network signalling FIFO read failure 4194304 : adnAeiPortUSFRF user signalling FIFO read failure 8388608 : adnAeiPortUFWF user FIFO write failure 16777216 : adnAeiPortUSFOF user signalling FIFO overflow 33554432 : adnAeiPortNICI cells received on non-active ICI (Internal Communication Interface) 67108864 : adnAeiPortNCRC CRC errors detected on network side 134217728 : adnAeiPortNAAL AAL (ATM Adaptation Layer) sequence error on network side 268435456 : adnAeiPortUCRC CRC errors detected on user side 536870912 : adnAeiPortUAAL AAL sequence error on user side 2147483648: adnAeiPortSFIFO load sharing FIFO overflow For the BBTS1C and BBTP3C boards, the bit positions are : 1 : adnAeiPortOOS synchronization fault ATM Electrical Interface 2 : adnAeiPortLOS synchronization fault 8 bit parallel Atm Internal Interface 4 : adnAeiPortNFOF network FIFO overflows 16 : adnAeiPortCECH corrected errors in cell header 32 : adnAeiPortUCECH uncorrected errors in cell header 256 : adnAeiPortNPE parity errors on payload 4096 : adnAeiPortNMA1 no active maintenance cell received 16384 : adnAeiPortEMA1 error active maintenance cell received 67108864 : adnAeiPortNCRC CRC errors detected on payload field 134217728 : adnAeiPortNAAL AAL (ATM Adaptation Layer) sequence error in AEI reception N.B.: This variable is significant when the operational state of the port is enabled. When there is no port error, this variable has the value 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAeiPortErOOSCounter 3.1.637.3.1.5.15.23.1.5
The counter associated with the duration of the out of synchronization. expressed in milliseconds; counter #0 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErNFOFCounter 3.1.637.3.1.5.15.23.1.6
The counter associated with the number of network FIFO overflow intervals; counter #2 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErCECHCounter 3.1.637.3.1.5.15.23.1.7
The counter associated with the number of corrected errors in cell header; counter #4 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErUCECHCounter 3.1.637.3.1.5.15.23.1.8
The counter associated with the number of uncorrected errors in cell header; counter #5 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErNPECounter 3.1.637.3.1.5.15.23.1.9
The counter associated with the number of parity errors on payload field of cells; counter #8 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErNMA1Counter 3.1.637.3.1.5.15.23.1.10
The counter associated with the number of lost data maintenance cells; counter #12 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErEMA1Counter 3.1.637.3.1.5.15.23.1.11
The counter associated with the number of data maintenance cells received with error indication; counter #14 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErNICICounter 3.1.637.3.1.5.15.23.1.12
The counter associated with the number of cells received on non active internal channel identifier (ICI); counter #25 of the ATM core this counter is not relevant for the HBCEx boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErNCRCCounter 3.1.637.3.1.5.15.23.1.13
The counter associated with the number of CRC errors on network side; counter #26 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErNAALCounter 3.1.637.3.1.5.15.23.1.14
The counter associated with the number of ATM adaptation layer (AAL) sequence errors on network side; counter #27 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErLOSCounter 3.1.637.3.1.5.15.23.1.15
The counter associated with the loss of synchronization intervals; counter #1 of the ATM core; this counter is only relevant for the matrix board, for the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErRTAGCounter 3.1.637.3.1.5.15.23.1.16
The counter associated with the number of unallowed routing tags; counter #9 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErURCCounter 3.1.637.3.1.5.15.23.1.17
The counter associated with the number of unrouted cells; counter #30 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErIEMRAMPCounter 3.1.637.3.1.5.15.23.1.18
The counter associated with the number of BGIEM chip RAM parity errors; counter #3 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErCRCMA1Counter 3.1.637.3.1.5.15.23.1.19
The counter associated with the number of CRC errors on payload field of maintenance active cells of type 1 (MA1); counter #6 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards, the BBTP3C boards and for the HBCEx boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErCRCSICCounter 3.1.637.3.1.5.15.23.1.20
The counter associated with the number of CRC errors on payload field of self identified cells (SIC); counter #7 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards, the BBTP3C boards and for the HBCEx boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErNSFOFCounter 3.1.637.3.1.5.15.23.1.21
The counter associated with the number of network signalling FIFO overflows; counter #17 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErNFWFCounter 3.1.637.3.1.5.15.23.1.22
The counter associated with the number of network FIFO write failures; counter #18 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErSFWFCounter 3.1.637.3.1.5.15.23.1.23
The counter associated with the number of signalling FIFO write failures; counter #19 of the ATM core; this counter is not relevant for the matrix board., the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErNSFRFCounter 3.1.637.3.1.5.15.23.1.24
The counter associated with the number of network signalling FIFO read failures; counter #20 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErUSFRFCounter 3.1.637.3.1.5.15.23.1.25
The counter associated with the number of user signalling FIFO read failures; counter #22 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErUFWFCounter 3.1.637.3.1.5.15.23.1.26
The counter associated with the number of user FIFO write failures; counter #23 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErUSFOFCounter 3.1.637.3.1.5.15.23.1.27
The counter associated with the number of user signalling FIFO overflows; counter #24 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErUCRCCounter 3.1.637.3.1.5.15.23.1.28
The counter associated with the number of CRC errors ion user side; counter #28 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards, the BBTP3C boards and for the HBCEx boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErUAALCounter 3.1.637.3.1.5.15.23.1.29
The counter associated with the number of ATM adaptation layer (AAL) sequence errors on user side; counter #29 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards, the BBTP3C boards and for the HBCEx boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortErSFIFOCounter 3.1.637.3.1.5.15.23.1.30
The counter associated with the number of load sharing FIFO overflows; counter #31 of the ATM core; this counter is not relevant for the matrix board, the BBTS1C boards and for the BBTP3C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortCEMStatus 3.1.637.3.1.5.15.23.1.31
This variable indicates the port status. It is a bit map represented as a sum; therefore it can represent multiple failures. This variable is only significant for CEM8 boards. The bit positions are : 1 : adnAeiPortOOS out-of-synchronization 4 : adnAeiPortNFOF network FIFO overflows 8 : adnAeiPortIEMRAMP BGIEM chip RAM parity errors 16 : adnAeiPortCECH corrected errors in cell header 32 : adnAeiPortUCECH uncorrected errors in cell header 256 : adnAeiPortNPE parity errors on payload 4096 : adnAeiPortNMA1 no active maintenance cell received 16384 : adnAeiPortEMA1 active maintenance cell received with error indication 131072 : adnAeiPortNSFOF network signalling FIFO overflow 262144 : adnAeiPortNFWF network FIFO write failure 524288 : adnAeiPortSFWF signalling FIFO write failure 1048576 : adnAeiPortNSFRF network signalling FIFO read failure 4194304 : adnAeiPortUSFRF user signalling FIFO read failure 8388608 : adnAeiPortUFWF user FIFO write failure 16777216 : adnAeiPortUSFOF user signalling FIFO overflow 67108864 : adnAeiPortNCRC CRC errors detected on network side 134217728 : adnAeiPortNAAL AAL (ATM Adaptation Layer) sequence error on network side 2147483648: adnAeiPortSFIFO load sharing FIFO overflow N.B.: This variable is significant when the operational state of the port is enabled. When there is no port error, this variable has the value 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAeiPortTraCounterTable 3.1.637.3.1.5.15.24
This table is the ATM electrical interface (AEI) port traffic counters table. The counters are classified according to the board type. Some are specific to the broadband ATM switching element (BBASE) board also called the matrix board.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAeiPortTraCounterEntry

adnAeiPortTraCounterEntry 3.1.637.3.1.5.15.24.1
An entry in the ATM electrical interface (AEI) port traffic counters table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAeiPortTraCounterEntry  

adnAeiPortTraPTPSetRqCounter 3.1.637.3.1.5.15.24.1.1
The counter associated with the number of point-to-point (PTP) setup requests; counter #1 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTMSetRqCounter 3.1.637.3.1.5.15.24.1.2
The counter associated with the number of point-to-multipoint (PTM) setup requests; counter #2 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTPSetRjBCounter 3.1.637.3.1.5.15.24.1.3
The counter associated with the number of point-to-point (PTP) setup rejects due to blocking; counter #3 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTMSetRjBCounter 3.1.637.3.1.5.15.24.1.4
The counter associated with the number of point-to-multipoint (PTM) setup rejects due to blocking; counter #4 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTPSetRjCCounter 3.1.637.3.1.5.15.24.1.5
The counter associated with the number of point-to-point (PTP) setup rejects due to communication; counter #5 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTMSetRjCCounter 3.1.637.3.1.5.15.24.1.6
The counter associated with the number of point-to-multipoint (PTM) setup rejects due to communication; counter #6 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTPSetTrCounter 3.1.637.3.1.5.15.24.1.7
The counter associated with the number of point-to-point (PTP) setup trials; counter #7 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTMSetTrCounter 3.1.637.3.1.5.15.24.1.8
The counter associated with the number of point-to-multipoint (PTM) setup trials; counter #8 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTPCnxCounter 3.1.637.3.1.5.15.24.1.9
The counter associated with the number of point-to-point (PTP) connections in progress; counter #13 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnAeiPortTraPTMCnxCounter 3.1.637.3.1.5.15.24.1.10
The counter associated with the number of point-to-multipoint (PTM) connections in progress; counter #14 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnAeiPortTraEFCCCounter 3.1.637.3.1.5.15.24.1.11
The counter associated with the number of established forward connection component; counter #17 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTPBWICIRqCounter 3.1.637.3.1.5.15.24.1.12
The counter associated with the number of point-to-point (PTP) bandwith or internal channel identifier (BW,ICI) requests; counter #4 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTMBWICIRqCounter 3.1.637.3.1.5.15.24.1.13
The counter associated with the number of point-to-multipoint (PTM) bandwith or internal channel identifier (BW,ICI) requests; counter #5 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTPBWRjCounter 3.1.637.3.1.5.15.24.1.14
The counter associated with the number of point-to-point (PTP) bandwith (BW) requests failure; counter #6 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTMBWRjCounter 3.1.637.3.1.5.15.24.1.15
The counter associated with the number of point-to-multipoint (PTM) bandwith (BW) requests failure; counter #7 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTPICIRjCounter 3.1.637.3.1.5.15.24.1.16
The counter associated with the number of point-to-point (PTP) internal channel identifier (ICI) requests failure; counter #8 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPTMICIRjCounter 3.1.637.3.1.5.15.24.1.17
The counter associated with the number of point-to-multipoint (PTM) internal channel identifier (ICI) requests failure; counter #9 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraPeakBWCounter 3.1.637.3.1.5.15.24.1.18
The counter associated with the reserved peak bandwith (BW); counter #10 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnAeiPortTraFPTPICICounter 3.1.637.3.1.5.15.24.1.19
The counter associated with the number of free point-to-point (PTP) internal channel identifiers (ICI); counter #12 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

adnAeiPortTraMPriorBWCounter 3.1.637.3.1.5.15.24.1.20
The counter associated with the reserved mean priority bandwith (BW); Counter #14 of the ATM core; this counter is only relevant for the matrix board.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Gauge  

adnAeiPortTraInCellsCounter 3.1.637.3.1.5.15.24.1.21
The counter associated with the number of incoming cells; counter #15 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraOutCellsCounter 3.1.637.3.1.5.15.24.1.22
The counter associated with the number of outgoing cells; counter #16 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAeiPortTraEBCCCounter 3.1.637.3.1.5.15.24.1.23
The counter associated with the number of established backward connection component; counter #18 of the ATM core; this counter is not relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtTable 3.1.637.3.1.5.15.25
This table is the HSC Board Traffic Management parameters table. This is only relevant for HSC boards with output buffers
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnHscBoardTrMgtEntry

adnHscBoardTrMgtEntry 3.1.637.3.1.5.15.25.1
An entry in the ATM Traffic Management parameters table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnHscBoardTrMgtEntry  

adnHscBoardTrMgtOBLineAssig 3.1.637.3.1.5.15.25.1.1
This indicates the line number the output buffer is assigned to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtHOBSize 3.1.637.3.1.5.15.25.1.2
This indicates the size of high priority output buffer; the allowed values are : - 115(cells) for BBT1B and BBE1B boards - 1..256(cells) for other HSC boards with output buffers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtMOBSize 3.1.637.3.1.5.15.25.1.3
This indicates the size of medium priority output buffer; For BBTS1C boards : the value range of the size is 0..7255 (cells); For BBTP3C boards : the value range of the size is 0..3627 (cells); For the other HSC boards with output buffers : the value range of the size is 0..16383(cells); this is not relevant for HSC boards without a medium priority output buffer (e.g. BBT1B and BBE1B).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtLOBSize 3.1.637.3.1.5.15.25.1.4
This indicates the size of low priority output buffer; For BBE1B and BBT1B boards : the allowed value is 2537(cells). For BBTS1C boards : adnHscBoardTrMgtLOBSize = 7256 - adnHscBoardTrMgtHOBSize - adnHscBoardTrMgtMOBSize. For BBTP3C boards : adnHscBoardTrMgtLOBSize = 3628 - adnHscBoardTrMgtHOBSize - adnHscBoardTrMgtMOBSize. For the other HSC boards with output buffers : adnHscBoardTrMgtLOBSize = 16384 - adnHscBoardTrMgtHOBSize - adnHscBoardTrMgtMOBSize.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtHOBSCDTh 3.1.637.3.1.5.15.25.1.5
This indicates the Selective Cell Discard (SCD) threshold in high priority output buffer (OB); when the filling of the high priority OB reaches the threshold, any incoming cell which internal cell loss priority equal to 1 will be discarded; due to BGTOB chip constraint, the value of the threshold is the high priority OB size. (adnHscBoardTrMgtHOBSize).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtMOBSCDTh 3.1.637.3.1.5.15.25.1.6
This indicates the Selective Cell Discard (SCD) threshold in medium priority output buffer (OB); when the filling of the medium priority OB reaches the threshold, any incoming cell which internal cell loss priority equal to 1 will be discarded; the value range of the threshold is 0..adnHscBoardTrMgtMOBSize(cells); this is not relevant for HSC boards without a medium priority output buffer (e.g. BBT1B and BBE1B).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtLOBSCDTh 3.1.637.3.1.5.15.25.1.7
This indicates the Selective Cell Discard (SCD) threshold in low priority output buffer (OB). when the filling of the low priority OB reaches the threshold, any incoming cell which internal cell loss priority is equal to 1 will be discarded; the value range of the threshold is 0..adnHscBoardTrMgtLOBSize(cells); For BBE1B and BBT1B boards : the value is multiple of 256.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtHOBEFCIOnTh 3.1.637.3.1.5.15.25.1.8
This indicates the Explicit Forward Congestion Indication (EFCI) activation threshold in high priority output buffer (OB); EFCI is generated towards the receiver termination point, in order to prevent congestion situation to be encountered within the output buffer; EFCI tagging is activated as soon as the activation threshold is reached; EFCI tagging is stopped as soon as the filling of the OB is below the EFCI desactivation threshold; due to BGTOB chip constraint, the value of the threshold is adnHscBoardTrMgtHOBSize (cells); this is only relevant for HSC board with a high priority output buffer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtMOBEFCIOnTh 3.1.637.3.1.5.15.25.1.9
This indicates the Explicit Forward Congestion Indication (EFCI) activation threshold in medium priority output buffer (OB); EFCI is generated towards the receiver termination point, in order to prevent congestion situation to be encountered within the output buffer; EFCI tagging is activated as soon as the activation threshold is reached; EFCI tagging is stopped as soon as the filling of the OB is below the EFCI desactivation threshold; the EFCI desactivation threshold is equal to the activation threshold minus 1/10 of the activation threshold; the value range of the threshold is 0..adnHscBoardTrMgtMOBSize; this is not relevant for HSC boards without a medium priority output buffer (e.g. BBT1B and BBE1B)..
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtLOBEFCIOnTh 3.1.637.3.1.5.15.25.1.10
This indicates the Explicit Forward Congestion Indication (EFCI) activation threshold in low priority output buffer (OB); EFCI is generated towards the receiver termination point, in order to prevent congestion situation to be encountered within the output buffer; EFCI tagging is activated as soon as the activation threshold is reached; EFCI tagging is stopped as soon as the filling of the OB is below the EFCI desactivation threshold; the EFCI desactivation threshold is equal to the activation threshold minus 1/10 of the activation threshold; the value range of the threshold is 0..adnHscBoardTrMgtLOBSize; this is only relevant for HSC board with a low priority output buffer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtHOBEFCIOffTh 3.1.637.3.1.5.15.25.1.11
This indicates the Explicit Forward Congestion Indication (EFCI) activation threshold in high priority output buffer (OB); EFCI is generated towards the receiver termination point, in order to prevent congestion situation to be encountered within the output buffer; EFCI tagging is activated as soon as the activation threshold is reached; EFCI tagging is stopped as soon as the filling of the OB is below the EFCI desactivation threshold; due to BGTOB chip constraint, the value of the threshold is adnHscBoardTrMgtHOBSize (cells); this is only relevant for HSC board with a high priority output buffer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtMOBEFCIOffTh 3.1.637.3.1.5.15.25.1.12
This indicates the Explicit Forward Congestion Indication (EFCI) activation threshold in medium priority output buffer (OB); EFCI is generated towards the receiver termination point, in order to prevent congestion situation to be encountered within the output buffer; EFCI tagging is activated as soon as the activation threshold is reached; EFCI tagging is stopped as soon as the filling of the OB is below the EFCI desactivation threshold; the EFCI desactivation threshold is equal to the activation threshold minus 1/10 of the activation threshold; the value range of the threshold is 0..adnHscBoardTrMgtMOBSize; this is not relevant for HSC boards without a medium priority output buffer (e.g. BBT1B and BBE1B).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtLOBEFCIOffTh 3.1.637.3.1.5.15.25.1.13
This indicates the Explicit Forward Congestion Indication (EFCI) desactivation threshold in low priority output buffer (OB); EFCI is generated towards the receiver termination point, in order to prevent congestion situation to be encountered within the output buffer; EFCI tagging is activated as soon as the activation threshold is reached; EFCI tagging is stopped as soon as the filling of the OB is below the EFCI desactivation threshold; the EFCI desactivation threshold is equal to the activation threshold minus 1/10 of the activation threshold; the value range of the threshold is 0..adnHscBoardTrMgtLOBSize; this is only relevant for HSC board with a low priority output buffer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtHOBObsTh 3.1.637.3.1.5.15.25.1.14
This indicates the observation threshold in high priority output buffer; when the observation threshold is overpassed, the adnHscBoardTrMgtHOBObsCounter value increases; the value range of the threshold is 0..(adnHscBoardTrMgtHOBSize - 1)(cells); this is not relevant for BBT1B and BBE1B boards.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtMOBObsTh 3.1.637.3.1.5.15.25.1.15
This indicates the observation threshold in medium priority output buffer; when the observation threshold is overpassed, the adnHscBoardTrMgtMOBObsCounter value increases; the value range of the threshold is 0..(adnHscBoardTrMgtMOBSize - 1) (cells); this is not relevant for HSC boards without a medium priority output buffer (e.g. BBT1B and BBE1B)..
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtLOBObsTh 3.1.637.3.1.5.15.25.1.16
This indicates the observation threshold in low priority output buffer; when the observation threshold is overpassed, the adnHscBoardTrMgtLOBObsCounter value increases; the value range of the threshold is 0..(adnHscBoardTrMgtLOBSize - 1) (cells); this is not relevant for BBT1B and BBE1B boards.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnHscBoardTrMgtOBStatus 3.1.637.3.1.5.15.25.1.17
This variable indicates the output buffers overflows status. It is a bit map represented as a sum. The bit positions are : 1 : high priority output buffer overflow 2 : medium priority output buffer overflow 4 : low priority output buffer overflow N.B.1:When there is no overflow within an output buffer, the corresponding bit has the value '0'. N.B.2:For BBE1B and BBT1B boards, bit position 2 is not significant.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnHscBoardTrMgtHOBCounter 3.1.637.3.1.5.15.25.1.18
The counter associated with the duration of overflows on high priority output buffer; this counter is not relevant for HSC boards without a high priority output buffer. expressed in milliseconds; counter #26 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtMOBCounter 3.1.637.3.1.5.15.25.1.19
The counter associated with the duration of overflows on medium priority output buffer; this counter is not relevant for HSC boards without a medium priority output buffer (e.g. BBT1B and BBE1B); expressed in milliseconds; counter #25 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtLOBCounter 3.1.637.3.1.5.15.25.1.20
The counter associated with the duration of overflows on low priority output buffer; this counter is not relevant for HSC boards without a low priority output buffer; expressed in milliseconds; counter #19 of the ATM core.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtMOBSCDCounter 3.1.637.3.1.5.15.25.1.21
The counter associated with the number of Selective Cell Discard(SCD) activations on medium priority output buffer; this counter is not relevant for HSC boards without a medium priority output buffer (e.g. BBT1B and BBE1B).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtLOBSCDCounter 3.1.637.3.1.5.15.25.1.22
The counter associated with the number of Selective Cell Discard (SCD) activations on low priority output buffer; this counter is not relevant for HSC boards without a low priority output buffer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtMOBEFCICounter 3.1.637.3.1.5.15.25.1.23
The counter associated with the number of Explicit Forward Congestion Indication (EFCI) activations on medium priority output buffer; counter #2 of the ATM core; this counter is not relevant for HSC boards without a medium priority output buffer (e.g. BBT1B and BBE1B).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtLOBEFCICounter 3.1.637.3.1.5.15.25.1.24
The counter associated with the number of Explicit Forward Congestion Indication (EFCI) activations on low priority output buffer; counter #3 of the ATM core; this counter is not relevant for HSC boards without a low priority output buffer and for BBE1B and BBT1B boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtMOBTPDCounter 3.1.637.3.1.5.15.25.1.25
The counter associated with the number of Tail Packet Discard (TPD) activations on medium priority output buffer; counter #4 of the ATM core; this counter is not relevant for HSC boards without a medium priority output buffer (e.g. BBT1B and BBE1B), the BBTP3C boards and for the BBTS1C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtLOBTPDCounter 3.1.637.3.1.5.15.25.1.26
The counter associated with the number of Tail Packet Discard (TPD) activations on low priority outpur buffer; counter #5 of the ATM core; this counter is not relevant for HSC boards without a low priority output buffer, for the BBE1B boards, the BBT1B boards, the BBTP3C boards and for the BBTS1C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtHOBObsCounter 3.1.637.3.1.5.15.25.1.27
The counter associated with the number of observation threshold overpassings on high priority output buffer; this counter is not relevant for HSC boards without a high priority output buffer, for the BBE1B, the BBT1B boards, the BBTP3C boards and for the BBTS1C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtMOBObsCounter 3.1.637.3.1.5.15.25.1.28
The counter associated with the number of observation threshold overpassings on medium priority output buffer; this counter is not relevant for HSC boards board without a medium priority output buffer (e.g. BBT1B and BBE1B) and the BBTP3C boards and for the BBTS1C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnHscBoardTrMgtLOBObsCounter 3.1.637.3.1.5.15.25.1.29
The counter associated with the number of observation threshold overpassings on low priority output buffer; this counter is not relevant for HSC boards without a low priority output buffer, the BBE1B, the BBT1B boards, the BBTP3C boards and for the BBTS1C boards.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAseBoardTrMgtGroup 3.1.637.3.1.5.15.26
OBJECT IDENTIFIER    

adnAseBoardTrMgtSCDTh 3.1.637.3.1.5.15.26.1
This indicates the Selective Cell Discard (SCD) threshold; when the filling of the FIFO reaches the threshold, any incoming low priority cell will be discarded; the value range of this threshold is 0..255(cells); this is relevant only for the BBASEB matrix board.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnAseBoardTrMgtHMP0ObsTh 3.1.637.3.1.5.15.26.2
This indicates the first observation threshold; when the observation threshold is exceeded, the adnAseBoardTrMgtObs1Counter increases each time a cell is received; the value range of this threshold is 0..255(cells); this is relevant only for the matrix board.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnAseBoardTrMgtHMP1ObsTh 3.1.637.3.1.5.15.26.3
This indicates the second observation threshold; when the observation threshold is exceeded, the adnAseBoardTrMgtObs2Counter increases each time a cell is received; the value range of this threshold is 0..255(cells); this is relevant only for the matrix board.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnAseBoardTrMgtOBStatus 3.1.637.3.1.5.15.26.4
This variable indicates if cells are discarded because of FIFO overflow or Selective Cell Discard (SCD). It is a bit map represented as a sum. The bit positions are : 1 : Selective Cell Discard activated 2 : FIFO overflow N.B.:When there is neither overflow nor SCD activation, the corresponding bit has the value '0'. this is relevant only for the BBASEB matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAseBoardTrMgtK 3.1.637.3.1.5.15.26.5
This indicates the Connection Admission Control (CAC) overbooking factor for all AEI ports, expressed as a percentage; the value range of this percentage is 100..1000; this is relevant only for the matrix board.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnAseBoardTrMgtKUbr 3.1.637.3.1.5.15.26.6
This indicates the overbooking factor allowed for Unspecified Bit Rate (UBR) connections; the percentage is used to calculate the allocated bandwidth of UBR connections; this is relevant only for the BBASEB matrix board.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnPercent  

adnAseBoardTrMgtIFR 3.1.637.3.1.5.15.26.7
This indicates the Interface Filling Rate (IFR) for all AEI ports; this is relevant only for the matrix board.
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnPercent  

adnAseBoardTrMgtSCDCounter 3.1.637.3.1.5.15.26.8
The counter associated with the number of low priority cells lost due to Selective Cell Discard (SCD); counter #26 of the ATM core; this counter is only relevant for the BBASEB matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAseBoardTrMgtOVFLCounter 3.1.637.3.1.5.15.26.9
The counter associated with the number of high priority cells lost due to buffer overflow; counter #27 of the ATM core; this counter is only relevant for the BBASEB matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAseBoardTrMgtObs1Counter 3.1.637.3.1.5.15.26.10
The counter associated with the number of cells received since the first observation threshold is exceeded; counter #0 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAseBoardTrMgtObs2Counter 3.1.637.3.1.5.15.26.11
The counter associated with the number of cells received since the second observation threshold is exceeded; counter #1 of the ATM core; this counter is only relevant for the matrix board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnUCNodeErrorsAtmsup 3.1.637.3.1.9.1.17
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmsupIncTranId 3.1.637.3.1.9.1.17.1
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmsupIncTranType 3.1.637.3.1.9.1.17.2
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmsupIncIndex 3.1.637.3.1.9.1.17.3
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmsupSta 3.1.637.3.1.9.1.17.6
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmsupDM 3.1.637.3.1.9.1.17.8
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmsupValue 3.1.637.3.1.9.1.17.11
OBJECT IDENTIFIER    

adnCESBufferUnderBegin 3.1.637.3.1.6.3.19
This TRAP indicates that a cell starvation condition, confirmed after a persistency check, has begun on the Circuit Emulation Service connection. A cell starvation condition means that no more ATM cells are received on the ATM connection supporting the Circuit Emulation Service connection which means an underflow in the received cells buffer The persistency check consists in waiting a certain time (default value is 2.5 s) before sending the alarm
TRAP-TYPE    

adnCESBufferUnderEnd 3.1.637.3.1.6.3.20
This TRAP indicates that a cell starvation condition has ended on the Circuit Emulation Service connection. A cell starvation condition means that no more ATM cells are received on the ATM connection supporting the Circuit Emulation Service connection which means an underflow in the received cells buffer
TRAP-TYPE    

adnCES 3.1.637.3.1.5.20
OBJECT IDENTIFIER    

adnCESConfTable 3.1.637.3.1.5.20.1
A list of extra parameters associated to a Circuit Emulation Service connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnCESConfEntry

adnCESConfEntry 3.1.637.3.1.5.20.1.1
Extra parameters for describing a Circuit Emulation Service connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnCESConfEntry  

adnCESClockMode 3.1.637.3.1.5.20.1.1.1
It defines the synchronization mode associated to the Circuit Emulation Service connection: - use the value defined in atmfCESCbrClockMode - loop timing: proprietary mode used when the line is in loop timing mode
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER useAtmfClockMode(1), looptiming(2)  

adnCESTrunkCondData 3.1.637.3.1.5.20.1.1.2
It specifies the pattern to be sent in the data timeslot when trunk conditioning (fault condition) on Constant Bit Rate interface is activated. It only applies to structured data transfer service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnCESCondSignal 3.1.637.3.1.5.20.1.1.3
It specifies the pattern to be sent in the signalling nibble (ABCD bits of CAS signalling) when trunk conditioning (fault condition) on Constant Bit Rate interface is activated. It only applies to structured data transfer service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

adnCESUpDownTrapEnable 3.1.637.3.1.5.20.1.1.4
It indicates whether Circuit Emulation Service trap should be generated on the Constant Bit Rate interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

adnX3ErrorBeg 3.1.637.3.1.6.3.2
Indicates that a failure has appeared on the DS3/E3 interface.
TRAP-TYPE    

adnX3ErrorEnd 3.1.637.3.1.6.3.1
Indicates that a failure has been cleared on the DS3/E3 interface.
TRAP-TYPE    

adnX3CauseError 3.1.637.3.1.6.5.9
The cause of the DS3/E3 trap currently being sent. This variable occurs as a variable-binding of an SNMP Trap PDU.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER ds3e3LOS(0), ds3e3Unused1(1), ds3e3AIS(2), ds3e3RcvRDI(3), ds3e3Pbit(4), ds3e3Cbit(5), ds3e3CbitFEBE(6), ds3e3LOF(7), ds3e3Unused8(8), ds3e3FEBE(9), ds3e3RcvRDIP(10), ds3e3BIP8(11), ds3e3PlcpLOF(12), ds3e3UnavailablePeriod(13), ds3e3Perf15(14), ds3e3PerfDay(15), ds3e3LOCD(16), ds3e3CorrectedHEC(17), ds3e3UncorrectedHEC(18), ds3e3Unused19(19), ds3e3PlcpOOF(20), ds3e3LCV(21), ds3e3UpwardsFIFO(22), ds3e3Unused23(23), ds3e3Unused24(24), ds3e3Unused25(25), ds3e3DownwardsFIFO(26), ds3e3Unused27(27), ds3e3IdleCode(28), ds3e3OOF(29), ds3e3HBER(30), ds3e3AppModeChange(31)  

adnRs232 3.1.637.3.1.4.10.33
OBJECT IDENTIFIER    

adnRs232InSigTable 3.1.637.3.1.4.10.33.1
A list of port input control signal entries, implemented and visible to the software on the port, and useful to monitor.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnRs232InSigEntry

adnRs232InSigEntry 3.1.637.3.1.4.10.33.1.1
Input control signal status for a hardware port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRs232InSigEntry  

adnRs232InSigPortIndex 3.1.637.3.1.4.10.33.1.1.1
The value of adnRs232PortIndex for the port to which this entry belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnRs232InSigName 3.1.637.3.1.4.10.33.1.1.2
Identification of a hardware input signal, as follows: tm Test Mode lal Local Loop rdl Remote Loop x21cont X.21 Control x21ind X.21 Indication cts Clear To Send dsr Data Set Ready dcd Received Line Signal Detector The cts, dsr and dcd signals are repeated from RFC 1659 to provide an index to object adnRs232InSigDuration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER tm(1), lal(2), rdl(3), x21cont(4), x21ind(5), cts(6), dsr(7), dcd(8)  

adnRs232InSigState 3.1.637.3.1.4.10.33.1.1.3
The current input signal state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), on(2), off(3)  

adnRs232InSigChanges 3.1.637.3.1.4.10.33.1.1.4
The number of times the input signal has changed from 'on' to 'off' or from 'off' to 'on'. 'NoSuchInstance' is returned in case of the HBCEU board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnRs232InSigDuration 3.1.637.3.1.4.10.33.1.1.5
The duration the input signal has been in the 'on' state for the tm(1), cts(6), dsr(7), dcd(8) signals of the HBCEU board. The duration the input signal has been in the 'off' state for the x21ind(5) signal of the HBCEU board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnRs232OutSigTable 3.1.637.3.1.4.10.33.2
A list of port output control signal entries, implemented and visible to the software on the port, and useful to monitor.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnRs232OutSigEntry

adnRs232OutSigEntry 3.1.637.3.1.4.10.33.2.1
Output control signal status for a hardware port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRs232OutSigEntry  

adnRs232OutSigPortIndex 3.1.637.3.1.4.10.33.2.1.1
The value of adnRs232PortIndex for the port to which this entry belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnRs232OutSigName 3.1.637.3.1.4.10.33.2.1.2
Identification of a hardware output signal, as follows: tm Test Mode lal Local Loop rdl Remote Loop x21cont X.21 Control x21ind X.21 Indication cts Clear To Send dsr Data Set Ready dcd Received Line Signal Detector The cts, dsr and dcd signals are repeated from RFC 1659 for consistency with object adnRs232InSigName. The cts, dsr and dcd signals aren't used in adnRs232OutSigTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER tm(1), lal(2), rdl(3), x21cont(4), x21ind(5), cts(6), dsr(7), dcd(8)  

adnRs232OutSigState 3.1.637.3.1.4.10.33.2.1.3
The current output signal state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), on(2), off(3)  

adnRs232OutSigChanges 3.1.637.3.1.4.10.33.2.1.4
The number of times the output signal has changed from 'on' to 'off' or from 'off' to 'on'. 'NoSuchInstance' is returned in case of the HBCEU board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnRs232PortTable 3.1.637.3.1.4.10.33.3
A list of port entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnRs232PortEntry

adnRs232PortEntry 3.1.637.3.1.4.10.33.3.1
ADN specific parameters values for a port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRs232PortEntry  

adnRs232PortIndex 3.1.637.3.1.4.10.33.3.1.1
The value of ifIndex of the port
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnRs232PortDuration 3.1.637.3.1.4.10.33.3.1.2
The duration for which the line has been in the 'off' state. This object applies to V35 and V36 lines of the HBCEU board. The 'off' state of the line is defined by : NOT (dcd up AND tm down AND (dsr up OR cts up)).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

adnAtmInterfaceTCErrorBeg 3.1.637.3.1.6.3.13
Indicates that an error or warning has been detected by the Transmission/Convergence (TC) layer of the ATM interface. This error or warning is always confirmed. To be confirmed, an error must occur a designated number of times during a given period of time.
TRAP-TYPE    

adnAtmInterfaceTCErrorEnd 3.1.637.3.1.6.3.14
Indicates that a failure has been cleared on the ATM interface.
TRAP-TYPE    

adnAtmSaalDown 3.1.637.3.1.6.3.15
A problem occured on a Signalling ATM Adaptation Layer (SAAL) connection. This connection is not established.
TRAP-TYPE    

adnAtmSaalUp 3.1.637.3.1.6.3.16
The SAAL connection is established.
TRAP-TYPE    

adnAtmSigCniCheckDown 3.1.637.3.1.6.3.17
A problem occured during the CANP Network Interface (CNI) checking phase of an ATM trunk.
TRAP-TYPE    

adnAtmSigCniCheckUp 3.1.637.3.1.6.3.18
After disappearance of the error or warning, a trap is sent to NMS to indicate the return to a normal state.
TRAP-TYPE    

adnAtmCconnectDown 3.1.637.3.1.6.3.6
Specifies the cause of the error or warning that occurred on an ATM cross-connection. The ATM cross-connection can be at either VP or VC level. At VP level, the adnAtmVci variable is not significant (equals 0).
TRAP-TYPE    

adnAtmCconnectUp 3.1.637.3.1.6.3.7
After disappearance of the error or warning, a trap is sent to NMS to indicate the return to a normal state. The ATM cross-connection can be either at VP or VC level. At VP level, the adnAtmVci variable is not significant (0).
TRAP-TYPE    

adnAtmInterfaceConfError 3.1.637.3.1.6.3.8
Specifies a configuration inconsistency between two ATM trunks (CNIs).
TRAP-TYPE    

adnAtmVpi 3.1.637.3.1.6.5.14
Virtual Path Index (VPI) value on the ATM interface. Always significant.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmVci 3.1.637.3.1.6.5.15
Virtual Channel Index (VCI) value on the ATM interface. The not significant value is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmCconnectIndex 3.1.637.3.1.6.5.16
Index of the ATM cross-connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmCconnectAdminStatus 3.1.637.3.1.6.5.17
Value that identifies the administrative status of an ATM cross-connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmAdminStatus  

adnAtmCconnectOperStatus 3.1.637.3.1.6.5.18
Value that identifies the current operational status of an ATM cross-connection.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmUniOperStatus  

adnAtmCcCauseError 3.1.637.3.1.6.5.19
Cause of the User to Network Interface (UNI) cross- connection trap currently being sent. Occurs as a variable- binding of an SNMP Trap Packet Data. Unit (PDU).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER adnAtmCconnectMaxAttempts(1), adnAtmCconnectConfError(2)  

adnAtmCconnectLastCanpCause 3.1.637.3.1.6.5.26
Last Cell Alcatel Network Protocol (CANP) cause.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmCconnectLastErrorNodeID 3.1.637.3.1.6.5.27
The identifier of the node detecting the error.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnRoutingID  

adnAtmCconnectLastLocation 3.1.637.3.1.6.5.28
ATM forum location value in the cause information element.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmCconnectLastCause 3.1.637.3.1.6.5.29
ATM forum cause value in the cause information element.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmCconnectLastDiag 3.1.637.3.1.6.5.30
ATM forum diagnostic value in the cause information element.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmInterfaceTCCauseError 3.1.637.3.1.6.5.31
Variable that gives the cause of the ATM interface Transmission/Convergence trap currently being sent. Occurs as a variable-binding of an SNMP trap PDU.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER atmtcUnused0(0), atmtcUnused1(1), atmtcUnused2(2), atmtcUnused3(3), atmtcUnused4(4), atmtcUnused5(5), atmtcUnused6(6), atmtcUnused7(7), atmtcUnused8(8), atmtcUnused9(9), atmtcPlcpRcvRDI(10), atmtcUnused11(11), atmtcPlcpLOF(12), atmtcUnused13(13), atmtcUnused14(14), atmtcUnused15(15), atmtcLOCD(16), atmtcCorrectedHEC(17), atmtcUncorrectedHEC(18), atmtcUnused19(19), atmtcUnused20(20), atmtcUnused21(21), atmtcUpwardsFIFO(22), atmtcUnused23(23), atmtcUnused24(24), atmtcETtoLTLoss(25), atmtcUnused26(26), atmtcUnused27(27), atmtcUnused28(28), atmtcUnused29(29), atmtcUnused30(30), atmtcUnused31(31)  

adnAtmCconnectLastMachine 3.1.637.3.1.6.5.42
The machine number part of adnAtmCconnectLastErrorNodeID.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmCconnectLastArea 3.1.637.3.1.6.5.43
The area number part of adnAtmCconnectLastErrorNodeID.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmCconnectLastChassis 3.1.637.3.1.6.5.44
The chassis number detecting the error.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmCconnectLastSlot 3.1.637.3.1.6.5.45
The slot number of the board detecting the error.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnDsx1ErrorBeg 3.1.637.3.1.6.3.11
Indicates that a failure has appeared on the DS1/E1 interface.
TRAP-TYPE    

adnDsx1ErrorEnd 3.1.637.3.1.6.3.12
Indicates that a failure has been cleared on the DS1/E1 interface.
TRAP-TYPE    

adnDsx1ErrorCause 3.1.637.3.1.6.5.33
The cause of the DS1/E1 trap currently being sent. This variable occurs as a variable-binding of an SNMP Trap PDU.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER ds1e1LOS(0), ds1e1Unused1(1), ds1e1AIS(2), ds1e1RcvRDI(3), ds1e1Unused4(4), ds1e1Unused5(5), ds1e1Unused6(6), ds1e1LOF(7), ds1e1Unused8(8), ds1e1Unused9(9), ds1e1Unused10(10), ds1e1Unused11(11), ds1e1Unused12(12), ds1e1UnavailablePeriod(13), ds1e1Perf15(14), ds1e1PerfDay(15), ds1e1Unused16(16), ds1e1TS16AIS(17), ds1e1RSA(18), ds1e1LSMA(19), ds1e1Unused20(20), ds1e1HBER(21), ds1e1Unused22(22), ds1e1RLB(23), ds1e1Unused24(24), ds1e1Unused25(25), ds1e1Unused26(26), ds1e1Unused27(27), ds1e1Unused28(28), ds1e1Unused29(29), ds1e1LCMA(30), ds1e1Unused31(31)  

adnPmdDumpFileReady 3.1.637.3.1.6.1.11
The main PMD application sends this trap to the NMS to indicate that a PMD file is ready for collection. The full name of the PMD file is given. If adnPmdDumpExecutionReport has the value `alreadyBuilt', a PMD file already exists for the same fault, and the requested PMD has not been built. This fault has occurred for the adnPmdFrequencyCount time(s). adnPmdNodeSurveillance is set if the file has to be picked up by the NMS. This variable can be modified only by the NMS. adnPmdTargetIdentification indicates the chassis, slot and processor where the PMD has been built.
TRAP-TYPE    

adnPmdFailed 3.1.637.3.1.6.1.12
The main PMD application sends this trap to the NMS to indicate that a PMD has failed. If the PMD started and failed during execution, adnPmdDumpExecutionReport returns an error code of 'aborted'. If the PMD never started, then adnPmdDumpExecutionReport returns error code 'nok' (not okay). adnPmdNodeSurveillance is set if the file has to be picked up by the NMS. This variable can be modified only by the NMS. This variable is not relevant for the trap adnPmdFailed because the file has not been built. adnPmdTargetIdentification indicates the chassis, slot and processor where the PMD has failed.
TRAP-TYPE    

adnPmdMscCrashIndication 3.1.637.3.1.6.1.20
The main PMD sub-system sends this trap to the NMS to indicate that a crash occurred on a MSC (Medium Speed Coupler). This trap is only a crash quick report. To get more information, the operator has to check the PMD file (if it has been authorized to be created : see adnPmdMib).
TRAP-TYPE    

adnPmdDumpFilePathName 3.1.637.3.1.6.5.21
PMD pathname built in the NMS transfer directory.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnPmdDumpExecutionReport 3.1.637.3.1.6.5.22
If the PMD has actually been built, it is ok(1). If it has not been built because the filter mechanism knows that a PMD was previously built for the same fault, it is alreadyBuilt(3), and the file name is filled with the known value.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER ok(1), aborted(2), alreadyBuilt(3), nok(4)  

adnPmdFailedDiagnostic 3.1.637.3.1.6.5.23
The diagnostic is sent to explain why the PMD failed. The significance of each value is described in the document 3CB00572AAAAUBZZA.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), badMessageReceived(2), noDataToDump(3), softwareInconsistency(4), cannotOpenFile(5), writeError(6), unixMoveError(7), unixCompressError(8), nectarMaintUnav(9), nectarMaintErrorReport(10), timeOut(11)  

adnPmdFrequencyCount 3.1.637.3.1.6.5.24
This variable indicates how often a particular fault is occurring.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnPmdTargetIdentification 3.1.637.3.1.6.5.25
This variable indicates the processor experiencing the fault. The variable is expressed with 5 digits. The first one gives the chassis number, the next two digits give the slot number and the two last digits give the processor number. So, the value CSSPP means that the PMD has been generated by the processor PP of the slot SS of the chassis C.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnPmdMscCrashClass 3.1.637.3.1.6.5.34
This field contains the class of the crash: - unknown(-1): the processor has been reset by an . external cause. - stop(0) : the reset has been asked by an process. - str(1) : a fatal str occurred. - system(2) : an exception or a system panic . occurred. - other(3) : other.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER unknown(-1), stop(0), str(1), system(2), other(3)  

adnPmdMscCrashOrigin 3.1.637.3.1.6.5.35
This field depends on the adnPmdMscCrashClass. If adnPmdMscCrashClass is 'str' then the str name is given. If adnPmdMscCrashClass is 'stop' the process name is given. If adnPmdMscCrashClass is 'system' the name of running process when the fault occurred is given.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnPmdMscCrashTime 3.1.637.3.1.6.5.36
This field is used to give the time the crash occurred at the MSC (Medium Speed Coupler) level.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnNodeTimeTicks  

adnTrapSonetBeg 3.1.637.3.1.6.3.4
Indicates that a failure has appeared on the Sonet/SDH interface.
TRAP-TYPE    

adnTrapSonetEnd 3.1.637.3.1.6.3.3
Indicates that a failure has been cleared on the Sonet/SDH interface.
TRAP-TYPE    

adnSonetTrapCause 3.1.637.3.1.6.5.10
Variable that gives cause of the Sonet trap currently being sent. Occurs as a variable-binding of an SNMP trap.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER sonetSectionLOS(0), sonetUnused1(1), sonetLineAIS(2), sonetLineRcvRDI(3), sonetUnused4(4), sonetLineHighBIP(5), sonetUnused6(6), sonetSectionLOF(7), sonetPathAIS(8), sonetPathFEBE(9), sonetPathRcvRDI(10), sonetPathBIP8(11), sonetPathLOP(12), sonetITUperfUnAvailablePeriod(13), sonetITUperf15(14), sonetITUperfDay(15), sonetTCOCD(16), sonetTCCorrectedHEC(17), sonetTCUnCorrectedHEC(18), sonetUnused19(19), sonetUnused20(20), sonetUnused21(21), sonetTCUpBufferOverflow(22), sonetMediumLaserDegradation(23), sonetMediumLaserTransmitSignalOut(24), sonetTCETtoLTLoss(25), sonetTCDownBufferOverflow(26), sonetMediumAppliqueFailure(27), sonetLineBIP(28), sonetSectionOOF(29), sonetUnused30(30), sonetUnused31(31), sonetBadBoardType(100)  

adnTrapATMCellLossBeg 3.1.637.3.1.6.3.9
Indicates that cells are discarded because of FIFO overflow.
TRAP-TYPE    

adnTrapATMCellLossEnd 3.1.637.3.1.6.3.10
Indicates that the discard of cells has been stopped.
TRAP-TYPE    

adnAtmCellLossTrapCause 3.1.637.3.1.6.5.32
Variable that gives cause of the ATM Traffic Management trap currently being sent. Occurs as a variable-binding of an SNMP trap.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER hmpOverflow(1), highOBOverflow(2), medOBOverflow(3), lowOBOverflow(4)  

adnHSSEquipStatusChange 3.1.637.3.1.6.1.2
This trap indicates that the indicated equipment has changed state. The trap is sent only if adnEquipTrapEnableMask has the bit set for the state or status that changed.
TRAP-TYPE    

adnEquipCause 3.1.637.3.1.6.5.8
This variable indicates the specific cause of the problem which has occurred on the equipment (chassis or board).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnEquipCause  

adnHSSBoardSwitchover 3.1.637.3.1.6.1.18
This trap indicates that a board switchover occurred.
TRAP-TYPE    

adnHSSBoardSwitchback 3.1.637.3.1.6.1.19
This trap indicates that a board switchback occurred.
TRAP-TYPE    

adnClockStatusChange 3.1.637.3.1.6.1.14
This trap signifies that one or more clocks on the indicated chassis have changed state.
TRAP-TYPE    

adnBbsynBoardAlarm 3.1.637.3.1.6.1.17
This trap indicates an alarm from the BBSYN board.
TRAP-TYPE    

adnHssStr 3.1.637.3.1.6.1.13
This trap indicates that a Software Trouble Report occurred inside the HSS
TRAP-TYPE    

adnHssStrName 3.1.637.3.1.6.5.11
The STR identifier within the HSS. This is a number unique to a specific STR event type.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnHssStrHeader 3.1.637.3.1.6.5.12
Header information in the STR which includes: STR indentifier (adnHssStrName) date and time urgency level sender identifier (node, board type, chassis, slot, processor) software package information
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

adnHssStrMoreInfo 3.1.637.3.1.6.5.13
Additional information eventually contained in the STR. This field may be empty.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

adnHssStrYear 3.1.637.3.1.6.5.46
The year of the STR appearance.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrMonth 3.1.637.3.1.6.5.47
The month of the STR appearance.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrDay 3.1.637.3.1.6.5.48
The day of the STR appearance.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrHour 3.1.637.3.1.6.5.49
The hour of the STR appearance.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrMinute 3.1.637.3.1.6.5.50
The minute of the STR appearance.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrSecond 3.1.637.3.1.6.5.51
The second of the STR appearance.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrLevel 3.1.637.3.1.6.5.52
The STR level : 1 : fatal for nobody 2 : fatal for the sending application 3 : fatal for the local processor 4 : fatal for the local board 5 : fatal for the node.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER nonFatal(1), applFatal(2), procFatal(3), boardFatal(4), nodeFatal(5)  

adnHssStrNode 3.1.637.3.1.6.5.53
Identify the node where the STR appears.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrBoardType 3.1.637.3.1.6.5.54
Board type of the board where the STR appears. (Used only by HSS development teams. The values are described in gif_hss_equip.h .)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrChassis 3.1.637.3.1.6.5.55
Chassis identifier in the node where the STR appears.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrSlot 3.1.637.3.1.6.5.56
Slot identifier in the chassis where the STR appears.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrProcessor 3.1.637.3.1.6.5.57
Processor number on the board where the STR appears.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrSwpid 3.1.637.3.1.6.5.58
The software package identifier.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnHssStrStadd 3.1.637.3.1.6.5.59
Address of the software package.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrFile 3.1.637.3.1.6.5.60
The source file name.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnHssStrLine 3.1.637.3.1.6.5.61
Line number in the source file.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrPc 3.1.637.3.1.6.5.62
Program counter.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnHssStrObject 3.1.637.3.1.6.5.63
The action or object that triggers the STR
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnHssStrErrorCode 3.1.637.3.1.6.5.64
Error code.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnFRAIWOversizedSDU 3.1.637.3.1.6.3.5
This TRAP indicates that at least one oversized AAL-SDU (ATM Adaptation Layer Service Data Unit) has been received on the indicated FR logical line.
TRAP-TYPE    

adnEquipStatusChange 3.1.637.3.1.6.1.1
This trap signifies that the indicated equipment has changed state. The trap is sent only if adnEquipTrapEnableMask has the bit set for the state or status that changed.
TRAP-TYPE    

adnAmAccountingFileReady 3.1.637.3.1.6.1.3
This trap indicates whether the accounting file, whose path the object following adnTrapCategory defines, is ready to be transferred to the NMS via FTP services.
TRAP-TYPE    

adnFmAlarmFileReady 3.1.637.3.1.6.1.4
This trap indicates whether the alarm file, whose path the object following adnTrapCategory defines, is ready to be transferred to the NMS via FTP services.
TRAP-TYPE    

adnPmStatisticsFileReady 3.1.637.3.1.6.1.5
This trap indicates whether the historical or interval statistics file, whose path the object following adnTrapCategory defines, is ready to be transferred to the NMS via FTP services.
TRAP-TYPE    

adnConfigStatus 3.1.637.3.1.6.1.6
This trap is sent in response to each NMS command or state change.
TRAP-TYPE    

adnNodeResync 3.1.637.3.1.6.1.7
This trap notifies the NMS that the CU board has been reinitialized.
TRAP-TYPE    

adnRoutingInaccuracyTrap 3.1.637.3.1.6.1.8
The first time the number of denied resource allocations exceeds a threshold during the previous 30 seconds, this trap is issued. When routing tables can again be successfully built during a threshold period, another trap is issued to clear this condition.
TRAP-TYPE    

adnRoutingInaccuracyTrapClear 3.1.637.3.1.6.1.9
After a potential routing table inaccuracy trap was sent, this trap generates to indicate that routing tables can be successfully built again. The number of denied resource allocations dropping lower than a threshold determines this change in condition.
TRAP-TYPE    

adnHssCuDownTrap 3.1.637.3.1.6.1.10
This trap is sent every time the node supervision sends a CU down message to ISOM.
TRAP-TYPE    

adnClockSourceUp 3.1.637.3.1.6.1.15
This trap indicates that a line configured to be a clock source has come up.
TRAP-TYPE    

adnClockSourceDown 3.1.637.3.1.6.1.16
This trap indicates that a line configured to be a clock source has gone down.
TRAP-TYPE    

adnFrVCSlowPoll 3.1.637.3.1.6.2.1
This trap is sent every time a PVC enters the slow poll state.
TRAP-TYPE    

adnFrVCExitSlowPoll 3.1.637.3.1.6.2.2
This trap indicates the return to a normal PVC call setup attempt polling interval, after the call was in the slow poll state.
TRAP-TYPE    

adnFrVCDown 3.1.637.3.1.6.2.3
Indicates that the PVC has been set to 'down' by an NMS command.
TRAP-TYPE    

adnFrVCUp 3.1.637.3.1.6.2.4
Indicates that the switch will attempt to make calls or accept calls for a particular PVC. The NMS has allowed the PVC to be put into service.
TRAP-TYPE    

adnFrDiscardOn 3.1.637.3.1.6.2.5
Indicates frame relay data is being discarded because of network congestion.
TRAP-TYPE    

adnFrDiscardOff 3.1.637.3.1.6.2.6
Exit from frame relay data discarded because of network congestion.
TRAP-TYPE    

adnFrChanDiscardOn 3.1.637.3.1.6.2.7
Indicates frame relay data is being discarded at the channel level because of network congestion.
TRAP-TYPE    

adnFrChanDiscardOff 3.1.637.3.1.6.2.8
Exit from frame relay data discarded at the channel level because of network congestion.
TRAP-TYPE    

adnMIBTrapVarsEquipStatusText 3.1.637.3.1.6.5.1
If present in an adnEquipStatusChange trap, this object contains diagnostic text describing the reason for the equipment status change.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnTrapCategory 3.1.637.3.1.6.5.2
For the trap currently being sent, category of the trap that occurs as a variable-binding of an SNMP trap PDU.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER crucial(1), administrative(2), critical(3), major(4), minor(5), shtr(6), diagnostic(7), cleared(8)  

adnTrapFrVCDLCIIndex 3.1.637.3.1.6.5.3
This object defines the index of the DLCI of the local end of the VC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTrapFrCongsState 3.1.637.3.1.6.5.4
Current state of congestion for the affected channel or interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnCongestLevels  

adnTrapFrIfType 3.1.637.3.1.6.5.5
Type of interface affected.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER frs(1), franp(2), iwf(3)  

adnTrapFrCongOrigin 3.1.637.3.1.6.5.6
Origin of the congestion trap.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER ingress-vc(1), egress-vc(2), ingress-channel(3), egress-channel(4), egress-cuf(5)  

adnTrapReason 3.1.637.3.1.6.5.7
The reason for sending this trap (usually, the type of the cause object). atm-line: ATM line, fr-line: Frame Relay line, lis-link: Local Inchannel Signalling (LIS) link, lapf-lapd-link: LAPF/LAPD protocol, nms-initiated: NMS-initiated via SNMP SET command, atm-interface: ATM interface, xfr-line: Alcatel protocol for Frame Relay PSX trunk, xcm-link: Alcatel protocol for X.25 PSX trunk, x25-gateway: X.25 link to other (non ACX) X.25 network, x75-gateway: X.75 link to other X.25 network, x25-link: PSX-ACX trunk (ACX is an X.25 PSX subscriber).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER atm-line(1), fr-line(2), lis-link(3), lapf-lapd-link(4), nms-initiated(5), atm-interface(6), xfr-line(7), xcm-link(8), x25-gateway(9), x75-gateway(10), x25-link(11)  

adnAtmInterfaceCauseError 3.1.637.3.1.6.5.20
Cause of the ATM interface error trap.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER adnAtmInterfaceBadUserNetFlg(1)  

adnTrapFrVCCos 3.1.637.3.1.6.5.67
Class of Service for Frame Relay.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnFrCos  

adnFlashUpdateStatus 3.1.637.3.1.6.1.24
This trap is sent for each board whose on-line or off-line flash update fails.
TRAP-TYPE    

adnBrdFlashUpdateErrorCode 3.1.637.3.1.6.5.68
This object identifies a specific error for flash update. Values are: msupTimeout - on-line flash update failed due to a Main Supervisor timeout. flashWriteError - on-line flash update failed due to a flash write error. offlineFlashUpdateError - off-line flash update failed.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER msupTimeout(1), flashWriteError(2), offlineFlashUpdateError(3)  

adnFlashBuildStatus 3.1.637.3.1.6.1.25
This trap is sent for each board whose flash volume build fails.
TRAP-TYPE    

adnBrdFlashBuildErrorCode 3.1.637.3.1.6.5.69
This object identifies a specific error for flash build. flashVolumeWriteError - an error occured while creating or writing the flash volume file on the Control Unit. This may be a disk space problem. openDescriptionFileError - the flash description file can not be opened. This may be due to a permission problem or to the absence of this file on the Control Unit. descriptionFileSyntaxError - there is some syntax error within the description file. flashComponentFileMissing - a file to be gathered in the flash volume can not be found on the Control Unit. nectarFileManagementError - a Nectar File Management error occured. otherError - any error other than the above ones.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER flashVolumeWriteError(1), openDescriptionFileError(2), descriptionFileSyntaxError(3), flashComponentFileMissing(4), nectarFileManagementError(5), otherError(6)  

adnDumThresholdViolation 3.1.637.3.1.6.1.26
This trap indicates that one of the thresholds for disk utilization in the managed filesystem under Disk Utilization Management in the Node Management Subsystem was violated.
TRAP-TYPE    

adnDumFileReady 3.1.637.3.1.6.1.27
This trap indicates that a file that the Network Management System normally retrieves from a managed node via FTP services is ready to be transferred to the Network Management System.
TRAP-TYPE    

adnIfAssocTable 3.1.637.3.1.5.19
A list of point to point associations between the PSX/ACX internal link interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIfAssocEntry

adnIfAssocEntry 3.1.637.3.1.5.19.1
An association entry containing ifIndex of the first interface, adnNodeIndex of the first node, ifIndex of the associated interface, adnNodeIndex of the associated node and the type of protocol used on these interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIfAssocEntry  

adnFirstIfIndex 3.1.637.3.1.5.19.1.1
The value of this object corresponds to the ifIndex of the first interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnFirstNodeIndex 3.1.637.3.1.5.19.1.2
The value of this object corresponds to the adnNodeIndex of the first node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAssocIfIndex 3.1.637.3.1.5.19.1.3
The value of this object corresponds to the ifIndex of the associated interface, this value is not significant in the case where adnProtocolType is g25 or x75. In that case a GET request on this OID will be replied with the response noSuchname into error-status field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAssocNodeIndex 3.1.637.3.1.5.19.1.4
The value of this object corresponds to the adnNodeIndex of the associated node, this value is not significant in the case where adnProtocolType is g25 or x75. In that case a GET request on this OID will be replied with the response noSuchname into error-status field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnProtocolType 3.1.637.3.1.5.19.1.5
The value of this object represents the protocol used on interfaces. xfr and xcm protocols are ALCATEL proprietary protocols that are used for PSX and ACX internal links. x25 is a standard protocol that is used for connecting an ACX configured as a concentrator to a PSX. g25 is an ALCATEL proprietary protocol that is used for connecting an ALCATEL 1100 NETWORK to another packet switching network via an X25 gateway link. x75 is a standard protocol used for connecting an ALCATEL 1100 NETWORK to another packet switching network via an X75 gateway link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER xfr(1), xcm(2), x25(3), g25(4), x75(5)  

adnPsxAcxEquipStatusChange 3.1.637.3.1.6.6.1
The indicated equipment has changed state. This trap is sent only if adnEquipTrapEnableMask has the bit set for the changed state or status.
TRAP-TYPE    

adnPsxVppStatusChange 3.1.637.3.1.6.6.2
The VPP of the indicated PSX has changed state. This trap is sent to the NMS for being forwarded in proprietary ASCII format to RATP management system
TRAP-TYPE    

adnPsxNmcAlarmCode 3.1.637.3.1.6.5.37
The value of this object is the code of the alarm received from the NMC. Common name: alarm code
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnPsxCouplerStatusChange 3.1.637.3.1.6.6.3
The indicated coupler has changed state. This trap is sent to the NMS for being forwarded in proprietary ASCII format to RATP management system.
TRAP-TYPE    

adnPsxFtdIndex 3.1.637.3.1.6.5.38
The value of this object corresponds to the adnEquipIndex of the FTD card. Common name: Equip Index
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnPsxFrontEndNumber 3.1.637.3.1.6.5.39
The value of this object corresponds to the Front end number in the alarm data. Common name: PSX Front End Number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnPsxCouplerIndex 3.1.637.3.1.6.5.40
The value of this object corresponds to the adnEquipIndex of the coupler. Common name: Equip Index
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnPsxCouplerNumber 3.1.637.3.1.6.5.41
The value of this object corresponds to the Coupler number in the alarm data. Common name: PSX Coupler Number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccTable 3.1.637.3.1.4.37.2
This table constitutes the ATM charging ticket. None of the objects in this table can be obtained via a GET command. These objects are visible only in a charging ticket. Most of these objects duplicate objects in other tables. They are concatenated here to allow the charging ticket to be sent as a single INMP/PFXI table to conserve space.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmCharEntry

adnAtmAccEntry 3.1.637.3.1.4.37.2.1
One instance of the ATM charging ticket.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmCharEntry  

adnAtmAccEquipType 3.1.637.3.1.4.37.2.1.1
This is the type of the equipment which generates this charging ticket. hss700 : Alcatel 1100 HSS Series 400/700, hss1000 : Alcatel 1100 HSS Series 1000. Common Name : Equipment Type.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), hss700(2), hss1000(3)  

adnAtmAccTicketVersion 3.1.637.3.1.4.37.2.1.2
This is the identifier of the version (format) of this ATM charging ticket. This object is numbered per type of equipment listed in adnAtmAccEquipType. adnAtmAccTicketVersion = 1 is the first value for Alcatel 1100 HSS Series 400/700. Common Name : Charging Ticket Version.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccLocalNodeId 3.1.637.3.1.4.37.2.1.3
This is the identifier of the node which generates this charging ticket. For HSS, the format of the ADN Node Routing ID is used : Bits 31-23 (9 bits) reserved for future use Bits 22-16 ( 7 bits) area identifier Bits 15-0 (16 bits) machine identifier Common Name : Local Node Identifier.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccLocalChassis 3.1.637.3.1.4.37.2.1.4
This is the chassis number where the interface is located. Common Name : Local Chassis
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccLocalSlot 3.1.637.3.1.4.37.2.1.5
This is the slot number of the interface in the chassis. Common Name : Local Slot
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccLocalLine 3.1.637.3.1.4.37.2.1.6
This is the line number in the slot. Common Name : Local Line
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccRemoteNodeId 3.1.637.3.1.4.37.2.1.7
This is the identifier of the node which supports the connection at the remote side. For HSS, the format of the ADN Node Routing ID is used : Bits 31-23 (9 bits) reserved for future use Bits 22-16 ( 7 bits) area identifier Bits 15-0 (16 bits) machine identifier Common Name : Remote Node Identifier.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccRemoteChassis 3.1.637.3.1.4.37.2.1.8
This is the chassis number where the remote interface is located. Common Name : Remote Chassis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccRemoteSlot 3.1.637.3.1.4.37.2.1.9
This is the slot number of the interface in the remote chassis. Common Name : Remote Slot
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccRemoteLine 3.1.637.3.1.4.37.2.1.10
This is the line number in the remote slot. Common Name : Remote Line
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccCallTerm 3.1.637.3.1.4.37.2.1.11
This object indicates a terminated ticket or an intermediate charging ticket : - terminated : PVC has been de-configured or disrupted SVC has been cleared (user or network cause) - intermediate : periodic collection of PVCs and long SVCs operator initiated collection of PVCs and SVCs. Intermediate tickets are for future use. Common Name : Call Terminated / not Terminated.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER other(1), terminated(2), intermediate(3)  

adnAtmAccInterfaceType 3.1.637.3.1.4.37.2.1.12
Type of the ATM interface on which generates this charging ticket. Common Name : ATM Interface Type.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER externalUni(1), nni(2), internalUniSig(3), virtualUni(4), physicalCni(5), routlogicalCni(6), nonroutlogicalCni(7), nonroutlogicalCniendtoend(8), internalUni(9)  

adnAtmAccConnectionType 3.1.637.3.1.4.37.2.1.13
This is the connection type : PVC versus SVC. Only the following values can be provided in a HSS charging ticket : - pvc, - svc. Common Name : Connection Type.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER pvc(1), svc(2), internalVc(3)  

adnAtmAccConnectionTopology 3.1.637.3.1.4.37.2.1.14
This object describes the characteristics of the connection at the location where this charging ticket is generated : Only the following values can be provided in a HSS charging ticket : - pointTopoint. Common Name : Connection Topology.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER pointToPoint(1), pointToMultipointRoot(3), pointToMultipointLeaf(4)  

adnAtmAccSourceDest 3.1.637.3.1.4.37.2.1.15
This object indicates the location of the node which generates this charging ticket : - source : the node receives the SET-UP message from the calling user. - destination : the node transmits the SET-UP message to the called user. - transit : this value is reserved for the 1000 HSS Series 1000 system (this system may generate charging ticket on trunks for observation purposes). Common Name : Source or Destination.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER source(1), destination(2), transit(3)  

adnAtmAccCallingPartyNumPlan 3.1.637.3.1.4.37.2.1.16
This is the type of numbering plan of the calling party number. Common Name : Numbering Plan, Num Plan.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER private(1), nsapE164(2), nativeE164(3), other(4), notSignificant(5)  

adnAtmAccCallingPartyLength 3.1.637.3.1.4.37.2.1.17
This is the number of significant digits in object adnAtmAccCallingParty. Common Name : Length of Calling Party Number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccCallingPartyNumber 3.1.637.3.1.4.37.2.1.18
This is the value of the calling party number (fixed length of 40 digits). Common Name : Calling Party Number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

adnAtmAccCalledPartyNumPlan 3.1.637.3.1.4.37.2.1.19
This is the type of numbering plan of the called party number. Common Name : Numbering Plan, Num Plan.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER private(1), nsapE164(2), nativeE164(3), other(4), notSignificant(5)  

adnAtmAccCalledPartyLength 3.1.637.3.1.4.37.2.1.20
This is the number of significant digits in object adnAtmAccCalledParty. Common Name : Length of Called Party Number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccCalledPartyNumber 3.1.637.3.1.4.37.2.1.21
This is the value of the called party number (fixed length of 40 digits). Common Name : Called Party Number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

adnAtmAccLocalVpi 3.1.637.3.1.4.37.2.1.22
The Virtual Path Identifier (VPI) value on the local ATM interface. Common Name : Virtual Path Identifier (VPI).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccLocalVci 3.1.637.3.1.4.37.2.1.23
The Virtual Channel Identifier (VCI) value on the local ATM interface. Common Name : Virtual Channel Identifier (VCI).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccRemVpi 3.1.637.3.1.4.37.2.1.24
The Virtual Path Identifier (VPI) value at the remote ATM interface. Common Name : Remote Virtual Path Identifier (VPI).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccRemVci 3.1.637.3.1.4.37.2.1.25
The Virtual Channel Identifier (VCI) value at the remote ATM interface. Common Name : Remote Virtual Channel Identifier (VCI).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccConnUniqueID 3.1.637.3.1.4.37.2.1.26
This object serves to uniquely identify the two charging tickets that are generated at both ends of an ATM connection. The ConnUniqueID is a value which is local to the calling ATM interface, it is incremented by the calling ATM interface. The ConnUniqueID is significant for : - each point to point connection, - each leaf of a point to point connection. Common name : Connection Unique Identifier
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccConnStartTime 3.1.637.3.1.4.37.2.1.27
In the first ticket generated : - this indicates the time of the CONNECT message when the establishment phase has been successful, - this indicates the time of the SET-UP message when the establishment phase has been unsuccessful, In the following intermediate tickets : - this indicates the time of the start of the interval. This is the coordinated universal time : number of seconds elapsed since 1970/01/01. Common name : Start Time.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

adnAtmAccConnDuration 3.1.637.3.1.4.37.2.1.28
This object represents the duration (tenths of a second) while the connection has been in the transfer phase. The total duration of a connection is to be accumulated over all the intermediate tickets that are generated for that connection. Common name : Duration of the Ticket.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmAccReqTransitDelay 3.1.637.3.1.4.37.2.1.29
This is the value of the transit delay required by the user for that connection. Common name : Required Transit Delay.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccCumulTransitDelay 3.1.637.3.1.4.37.2.1.30
This is the value of the transit delay provided by the network for that connection. Common name : Cumulative Transit Delay.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccTransferCapability 3.1.637.3.1.4.37.2.1.31
The ATM Transfer Capabilities (ATC) offered on a virtual cross-connection (Virtual Path Connection (VPC) and Virtual Channel Connection (VCC)): - Constant Bit Rate (CBR) ATC: CBR Real Time (RT), CBR Non Real Time (NRT) - Variable Bit Rate (VBR) ATC: VBR RT, VBR NRT - Unspecified Bit Rate (UBR) ATC. Common Name: ATM Transfer Capability (ATC).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ubr(1), cbrRtAggregate(2), vbrNrtAggregate(3), cbrNrtAggregate(4), vbrRtAggregate(5), cbrRtClpZero(6), vbrRtClpZero(7), vbrNrtClpZero(8)  

adnAtmAccTrmTrafficDescrType 3.1.637.3.1.4.37.2.1.32
The type of a virtual cross-connection (Virtual Path Connection (VPC) and Virtual Channel Connection (VCC)) traffic descriptor in the transmit direction. Depending on the value, the following traffic parameters (defined in the same direction) are initialized: - 'pcrCdv': .PcrAggregate PARAM1 .CdvTol PARAM2 - 'pcrCdvScrMbs': .PcrAggregate PARAM1 .CdvTol PARAM2 .ScrAggregate PARAM3 .MbsAggregate PARAM4 - 'pcrCdvPcr0': .PcrAggregate PARAM1 .CdvTol PARAM2 .PcrClpZero PARAM3 - 'pcrCdvScr0Mbs0': .PcrAggregate PARAM1 .CdvTol PARAM2 .ScrClpZero PARAM3 .MbsClpZero PARAM4 Common name : Traffic Descriptor in the Transmit Direction.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pcrCdv(1), pcrCdvScrMbs(2), pcrCdvPcr0(3), pcrCdvScr0Mbs0(4)  

adnAtmAccTrmParam1 3.1.637.3.1.4.37.2.1.33
PARAM1 : always equal to the Peak Cell Rate (PCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the transmit direction (switch point of view), of this Virtual Channel Link (VCL). Common Names: PARAM1, Transmit Peak Cell Rate (PCR) Aggregate, Transmit PCR Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccTrmParam2 3.1.637.3.1.4.37.2.1.34
PARAM2 : always equal to the Cell Delay Variation (CDV) tolerance of the traffic, in the transmit direction, of this Virtual Channel Link (VCL). Common Names: PARAM2, Transmit Cell Delay Variation (CDV) Tolerance, Transmit CDV Tolerance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccTrmParam3 3.1.637.3.1.4.37.2.1.35
Depending on the value of object 'adnAtmAccTrmTrafficDescrType' this object adnAtmAccTrmParam3 represents one of the following values : a) The Sustainable Cell Rate (SCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Sustainable Cell Rate (SCR) Aggregate, Transmit SCR Aggregate. b) The Peak Cell Rate (PCR) for the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Peak Cell Rate (PCR) Cell Loss Priority (CLP) 0, Transmit PCR CLP 0. c) The Sustainable Cell Rate (SCR) for the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Sustainable Cell Rate (SCR) Cell Loss Priority (CLP) 0, Transmit SCR CLP 0. Common Name : PARAM3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccTrmParam4 3.1.637.3.1.4.37.2.1.36
Depending on the value of object 'adnAtmAccTrmTrafficDescrType' this object adnAtmAccTrmParam4 represents one of the following values : a) The Maximum Burst Size (MBS) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Maximum Burst Size (MBS) Aggregate, Transmit MBS Aggregate. b) The Maximum Burst Size (MBS) for the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, of this Virtual Channel Link (VCL). Common Names: Transmit Maximum Burst Size (MBS) Cell Loss Priority (CLP) 0, Transmit MBS CLP 0 Common Name : PARAM4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccTrmTagging 3.1.637.3.1.4.37.2.1.37
Whether tagging option is enabled on the Cell Loss Priority (CLP) 0 traffic, in the transmit direction, when cells are not conformant, of this Virtual Channel Link (VCL). Common Name : Cell Tagging Option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

adnAtmAccTrmPacketDiscard 3.1.637.3.1.4.37.2.1.38
Whether packet discard option is enabled, in the transmit direction, of this Virtual Channel Link (VCL). When this option is enabled all the low priority cells in the remaining of an ATM Adaptation Layer (AAL) 5 frame are discarded, as soon as one of the cell of the frame has been discarded. Common Name : Tail Packet Discard.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

adnAtmAccRcvTrafficDescrType 3.1.637.3.1.4.37.2.1.39
The type of a virtual cross-connection (Virtual Path Connection (VPC) and Virtual Channel Connection (VCC)) traffic descriptor in the receive direction. Depending on the value, the following traffic parameters (defined in the same direction) are initialized: - 'pcrCdv': .PcrAggregate PARAM1 .CdvTol PARAM2 - 'pcrCdvScrMbs': .PcrAggregate PARAM1 .CdvTol PARAM2 .ScrAggregate PARAM3 .MbsAggregate PARAM4 - 'pcrCdvPcr0': .PcrAggregate PARAM1 .CdvTol PARAM2 .PcrClpZero PARAM3 - 'pcrCdvScr0Mbs0': .PcrAggregate PARAM1 .CdvTol PARAM2 .ScrClpZero PARAM3 .MbsClpZero PARAM4 Common name : Traffic Descriptor in the Receiving Direction.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pcrCdv(1), pcrCdvScrMbs(2), pcrCdvPcr0(3), pcrCdvScr0Mbs0(4)  

adnAtmAccRcvParam1 3.1.637.3.1.4.37.2.1.40
PARAM1 : always equal to the Peak Cell Rate (PCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the receiving direction (switch point of view), of this Virtual Channel Link (VCL). Common Names: PARAM1, Receive Peak Cell Rate (PCR) Aggregate, Receive PCR Aggregate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccRcvParam2 3.1.637.3.1.4.37.2.1.41
PARAM2 : always equal to the Cell Delay Variation (CDV) tolerance of the traffic, in the receiving direction, of this Virtual Channel Link (VCL). Common Names: PARAM2, Receive Cell Delay Variation (CDV) Tolerance, Receive CDV Tolerance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccRcvParam3 3.1.637.3.1.4.37.2.1.42
Depending on the value of object 'adnAtmAccTrmTrafficDescrType' this object adnAtmAccRcvParam3 represents one of the following values : a) The Sustainable Cell Rate (SCR) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the receivinG direction, of this Virtual Channel Link (VCL). Common Names: Receive Sustainable Cell Rate (SCR) Aggregate, Receive SCR Aggregate. b) The Peak Cell Rate (PCR) for the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Peak Cell Rate (PCR) Cell Loss Priority (CLP) 0, Receive PCR CLP 0. c) The Sustainable Cell Rate (SCR) for the Cell Loss PrioritY (CLP) 0 traffic, in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Sustainable Cell Rate (SCR) Cell Loss Priority (CLP) 0, Receive SCR CLP 0. Common Name : PARAM3.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccRcvParam4 3.1.637.3.1.4.37.2.1.43
Depending on the value of object 'adnAtmAccTrmTrafficDescrType' this object adnAtmAccRcvParam4 represents one of the following values : a) The Maximum Burst Size (MBS) for the aggregate traffic (Cell Loss Priority (CLP) 0+1), in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Maximum Burst Size (MBS) Aggregate, Receive MBS Aggregate. b) The Maximum Burst Size (MBS) for the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, of this Virtual Channel Link (VCL). Common Names: Receive Maximum Burst Size (MBS) Cell Loss Priority (CLP) 0, Receive MBS CLP 0. Common Name : PARAM4.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccRcvTagging 3.1.637.3.1.4.37.2.1.44
Whether tagging option is enabled on the Cell Loss Priority (CLP) 0 traffic, in the receiving direction, when cells are not conformant, of this Virtual Channel Link (VCL). Common Name : Cell Tagging Option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

adnAtmAccRcvPacketDiscard 3.1.637.3.1.4.37.2.1.45
Whether packet discard option is enabled, in the receiving direction, of this Virtual Channel Link (VCL). When this option is enabled all the low priority cells in the remaining of an ATM Adaptation Layer (AAL) 5 frame are discarded, as soon as one of the cell of the frame has been discarded. Common Name : Tail Packet Discard.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

adnAtmAccClearingCause 3.1.637.3.1.4.37.2.1.46
ATM forum cause value in the cause information element. This object is significant when the adnAtmAccCallTerm is equal to 'terminated'. Common Name : Clearing Cause.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmAccClearingDiag 3.1.637.3.1.4.37.2.1.47
First 4 bytes of the ATM forum diagnostic value in the cause information element. This object is significant when the adnAtmAccCallTerm is equal to 'terminated'. Common Name : Diagnostic Cause.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmAccVcDescriptor 3.1.637.3.1.4.37.2.1.48
This value is a configurable 64 byte identifier for each ATM and FR Permanent Virtual Circuit (PVC). When it is not configured, the accounting and statistical records do not include this object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adnNmsVpnTrapVars 3.1.637.3.1.5.21.1
OBJECT IDENTIFIER    

adnPVCConnectLowIfName 3.1.637.3.1.5.21.1.1
The ifName of the low endpoint interface for this PVC segment. The term low implies that this PVC segment end-point has the numerically lower ifIndex value than the connected/associated PVC segment end-point.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnPVCConnectHighIfName 3.1.637.3.1.5.21.1.2
The ifName of the high endpoint interface for this PVC segment. The term high implies that this PVC segment end-point has the numerically higher ifIndex value than the connected/associated PVC segment end-point.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DisplayString  

adnIpfwdsMIB 3.1.637.3.1.5.24
OBJECT IDENTIFIER    

adnIpIfStackTable 3.1.637.3.1.5.24.1
The table containing information on the relationship between an IP interface and its correponding AAL5 connections (or indices). Each of these multiplexed entities correspond to a conceptual row in the ifTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIpIfStackEntry

adnIpIfStackEntry 3.1.637.3.1.5.24.1.1
Information on a particular relationship between IP interface and its corresponding AAL5 connections. Each of the multiplexed ifIndex has a conceptual row in the ifTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIpIfStackEntry  

adnIpIfStackHigherLayer 3.1.637.3.1.5.24.1.1.1
The value of ifIndex corresponding to the IP interface which runs on 'top of' an AAL5 connection identified by a corresponding instance of adnIpIfStackLowerLayer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIpIfStackLowerLayer 3.1.637.3.1.5.24.1.1.2
The value of ifIndex corresponding to an AAL5 connection which runs 'below' the IP interface identified by the correponding instance of adnIpIfStackHigherLayer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIpIfStackStatus 3.1.637.3.1.5.24.1.1.3
The status of the relationship between two sub- layers. Changing the value of this object from 'active' to 'notInService' or 'destroy' will likely have consequences up and down a connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

adnUCNodeErrorsAtmces 3.1.637.3.1.9.1.26
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesIncTranId 3.1.637.3.1.9.1.26.1
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesIncTranType 3.1.637.3.1.9.1.26.2
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesOtherTran 3.1.637.3.1.9.1.26.3
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesDelReason 3.1.637.3.1.9.1.26.4
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesNotUpdPar 3.1.637.3.1.9.1.26.12
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesIncParVal 3.1.637.3.1.9.1.26.13
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesMissingPar 3.1.637.3.1.9.1.26.14
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesNotLinePar 3.1.637.3.1.9.1.26.100
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBadTsNb 3.1.637.3.1.9.1.26.101
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesLineNotCre 3.1.637.3.1.9.1.26.102
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBadLineType 3.1.637.3.1.9.1.26.103
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesAlrUnstr 3.1.637.3.1.9.1.26.104
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBundleNtCre 3.1.637.3.1.9.1.26.106
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesOtherLine 3.1.637.3.1.9.1.26.107
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBundleNtFnd 3.1.637.3.1.9.1.26.108
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesNtBundlePar 3.1.637.3.1.9.1.26.110
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBundleEmpty 3.1.637.3.1.9.1.26.111
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBadChassis 3.1.637.3.1.9.1.26.112
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBadSlot 3.1.637.3.1.9.1.26.113
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBadLine 3.1.637.3.1.9.1.26.114
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBadChannel 3.1.637.3.1.9.1.26.115
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBundleNtDel 3.1.637.3.1.9.1.26.116
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesBundleNtEmp 3.1.637.3.1.9.1.26.117
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesCnxNotDel 3.1.637.3.1.9.1.26.118
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesNoLineCre 3.1.637.3.1.9.1.26.121
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesAlrStruct 3.1.637.3.1.9.1.26.122
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesNoBundleCre 3.1.637.3.1.9.1.26.123
OBJECT IDENTIFIER    

adnUCNodeErrorsAtmcesOtherAtmCnx 3.1.637.3.1.9.1.26.124
OBJECT IDENTIFIER    

adnCvsiMIB 3.1.637.3.1.5.22
OBJECT IDENTIFIER    

adnCvsiSwitchInfoGroup 3.1.637.3.1.5.22.1
OBJECT IDENTIFIER    

adnCvsiTscChnlState 3.1.637.3.1.5.22.1.1
This entry represents the status of the Tag Switch Controller (TSC) channel. This channel connects the HSS with the Tag Switch Controller (TSC). Common Name: TSC Channel State
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(0), up(1)  

adnCvsiActiveSesId 3.1.637.3.1.5.22.1.2
This object indicates the active session ID of the CVSI slave in the HSS. This value changes whenever the slave is restarted, powered up, switched over to or manually reset. The session IDs are used by the Tag Switch Controller (TSC) to detect the loss of synchronization. Common Name: Active Session ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCvsiPwrUpSesId 3.1.637.3.1.5.22.1.3
This object indicates the power-up session ID of the CVSI slave in the HSS. This value reflects the session ID which was assigned when this slave was powered up. This value may be used by the Tag Switch Controller (TSC) for detecting a more serious synchronization loss. Common Name: PowerUp Session ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCvsiSlaveId 3.1.637.3.1.5.22.1.4
The slave ID corresponding to this instance of CVSI slave in HSS. This value is relevant if we have multiple slaves for each Tag Switch Controller (TSC). Common Name: Salve ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCvsiSwitchId 3.1.637.3.1.5.22.1.5
The switch ID for the HSS in this Tag Switching Router (TSR). Common Name: Switch ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCvsiControllerId 3.1.637.3.1.5.22.1.6
The controller ID for the Tag Switch Controller (TSC) in this Tag Switching Router (TSR). Common Name: Controller ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCvsiVersionId 3.1.637.3.1.5.22.1.7
The version of the CVSI code running in this Tag Switching Router (TSR). Common Name: Version ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCvsiMaxTrapWindow 3.1.637.3.1.5.22.1.8
The maximum number of traps which can be pending in the CVSI slave in the HSS. The traps will be pending if either the Tag Switch controller (TSC) hasn't acknowledged them, or they could not be sent for some reason. Common Name: Max Trap Window
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCvsiCurrTrapWindow 3.1.637.3.1.5.22.1.9
The number of pending traps in the CVSI slave in the HSS. The traps will be pending if either the Tag Switch Controller (TSC) hasn't acknowledged them, or they could not be sent for some reason. Common Name: Current Trap Window
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCvsiMaxCmdWindow 3.1.637.3.1.5.22.1.10
The maximum number of commands which can be pending in the CVSI slave in the HSS. A command will be pending if it has not been processed by the CVSI slave. This value is conveyed to the Tag Switch controller. Common Name: Max Cmd Window
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCvsiCurrCmdWindow 3.1.637.3.1.5.22.1.11
The number of pending commands in the CVSI slave in the HSS. A command will be pending if it has not been processed by the CVSI slave. Common Name: Current Cmd Window
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnCvsiSpacingState 3.1.637.3.1.5.22.1.12
Indicates whether traffic spacing is performed at all TDP interfaces. Spacing is used to reduce the peak to peak Cell Delay Variation (CDV) or to smoooth out bursty traffic coming into the network or to perform rate reduction. Common Name: Spacing State
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnCvsiSpacingRate 3.1.637.3.1.5.22.1.13
The rate at which traffic will be spaced if adnCvsiSpacingState is enabled. This rate is specified in cells per second. Common Name: Spacing Rate
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnCvsiTscIfIndex 3.1.637.3.1.5.22.1.14
The ifIndex of the TSC interface for this switch. Common Name: TSC ifIndex
Status: mandatory Access: read-write
OBJECT-TYPE    
  InterfaceIndex  

adnTdpIfTable 3.1.637.3.1.5.22.2
This table describes the TDP Interface. This table contains proprietary TDP interface configuration parameters. There is one entry per TDP interface. A TDP interface is a logical inter-node ATM interface or an ATM interface Connected to the Tag Switch Controller (TSC).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnTdpIfEntry

adnTdpIfEntry 3.1.637.3.1.5.22.2.1
An entry in the TDP interface table. There is one entry per TDP interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnTdpIfEntry  

adnTdpIfLogicalNum 3.1.637.3.1.5.22.2.1.1
This is the logical interface number of this TDP interface used by the Tag Switch Controller (TSC). Common Name: Logical If Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfPhyDesc 3.1.637.3.1.5.22.2.1.2
The description of the interface. It is the 20 byte physical descriptor of the interface provided to the Tag Switch Controller (TSC). Common Name: Interface Physical Desc
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnTdpIfType 3.1.637.3.1.5.22.2.1.3
This object provides the type of the interface The following are the possible values it can hold: 1 - Tag switch controller (TSC) interface, it connects the HSS to the Tag Switch Controller (TSC). 2 - Tag distribution protocol (TDP) access interface, it connects HSS to the Tag Edge Router (TER). 3 - Tag distribution protocol (TDP) trunk interace, it is the trunk interface for the tagged data. Common Name: Interface Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER tsc(1), tdpAccess(2), tdpTrunk(3)  

adnTdpIfState 3.1.637.3.1.5.22.2.1.4
This object provides the state of the interface The following are the possible values it can hold: 1 - Interface Pending, the interface is being set up 2 - Interface Congested, the interface is congested 3 - Interface Opened, the interface is up 4 - Interface Up 5 - Interface Down Common Name: Interface State
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pending(1), congested(2), opened(3), up(4), down(5)  

adnTdpIfTrapSent 3.1.637.3.1.5.22.2.1.5
This object tells whether a trap has been sent to the Tag Switch controller The following are the possible values it can hold. A trap has to be sent when an interface is brought up or down, This object tells whether a trap has been sent after this event. The interface status transition will be based on the the TDP interface status (adnTdpIfState). Common Name: Trap Sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  TruthValue  

adnTdpIfPhyIfIndex 3.1.637.3.1.5.22.2.1.6
The ifIndex of the physical line supporting this TDP interface. Common Name: Physical IfIndex
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnTdpIfPhyVpi 3.1.637.3.1.5.22.2.1.7
The Virtual Path Identifier (VPI) associated with the physical line supporting this TDP interface. Common Name: Physical VPI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfIuniIfIndex 3.1.637.3.1.5.22.2.1.8
The ifIndex of the internal UNI (I-UNI) on the Cell Interconnection Gateway (CIG) associated with this TDP interface. An internal UNI is used for the CVSI connection between the Tag Switch Controller (TSC) and HSS. It is zero if this is not a TSC interface (i.e if adnTdpIfType is not equal to 'tsc'). Common Name: IUNI IfIndex
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnTdpIfVciMax 3.1.637.3.1.5.22.2.1.9
The maximum VCI value allowed on this interface. Common Name: Max VCI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfVciMin 3.1.637.3.1.5.22.2.1.10
The minimum VCI value allowed on this interface. Common Name: Min VCI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfMaxTDPConn 3.1.637.3.1.5.22.2.1.11
The maximum number of Tag Distribution protocol (TDP) connections allowed on this interface. Common Name: Max Connections
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfAvailConnEgress 3.1.637.3.1.5.22.2.1.12
The number of available Tag Distribution Protocol (TDP) egress connections. The egress direction means the direction of outwards traffic flow from the interface. Common Name: Available Egress Connections
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfAvailConnIn 3.1.637.3.1.5.22.2.1.13
The number of available Tag Distribution Protocol (TDP) ingress connections. The ingress direction means the direction of inwards traffic flow into the interface. Common Name: Available Ingress Connections
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfMaxCellRateEgress 3.1.637.3.1.5.22.2.1.14
The maximum egress cell rate available. The cell rate is measured in Cells/Second. This value is configured when an interface is created. The egress direction means the direction of outwards traffic flow from the interface. A value of -1 indicates that the field is not used. Common Name: Max Egress Cell Rate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfMaxCellRateIn 3.1.637.3.1.5.22.2.1.15
The maximum ingress cell rate available. The cell rate is measured in Cells/Second. This value is configured when an interface is created. The ingress direction means the direction of inwards traffic flow into the interface. A value of -1 indicates that the field is not used. Common Name: Max Ingress Cell Rate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfAvailCellRateEgress 3.1.637.3.1.5.22.2.1.16
The available egress cell rate. The cell rate is measured in Cells/Second. The egress direction means the direction of outwards traffic flow from the interface. A value of -1 indicates that the field is not used. Common Name: Available Egress Cell Rate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfAvailCellRateIn 3.1.637.3.1.5.22.2.1.17
The available ingress cell rate. The cell rate is measured in Cells/Second. The ingress direction means the direction of inwards traffic flow into the interface. A value of -1 indicates that the field is not used. Common Name: Available Ingress Cell Rate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfMaxCtdEgress 3.1.637.3.1.5.22.2.1.18
The maximum Cell Transfer Delay (CTD) for egress. This value is configured when an interface is created. The egress direction means the direction of outwards traffic flow from the interface. A value of -1 indicates that the field is not used. Common Name: Max Egress CTD
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfMaxCtdIn 3.1.637.3.1.5.22.2.1.19
The maximum Cell Transfer Delay (CTD) for ingress. This value is configured when an interface is created. The ingress direction means the direction of inwards traffic flow into the interface. A value of -1 indicates that the field is not used. Common Name: Max Ingress CTD
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfMaxCdvEgress 3.1.637.3.1.5.22.2.1.20
The maximum Cell Delay Variation (CDV) for egress. This value is configured when an interface is created. The egress direction means the direction of outwards traffic flow from the interface. A value of -1 indicates that the field is not used. Common Name: Max Egress CDV
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfMaxCdvIn 3.1.637.3.1.5.22.2.1.21
The maximum Cell Delay Variation (CDV) for ingress. This value is configured when an interface is created. The ingress direction means the direction of inwards traffic flow into the interface. A value of -1 indicates that the field is not used. Common Name: Max Ingress CDV
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfRemoteLogicalNum 3.1.637.3.1.5.22.2.1.22
This entry represents the logical interface number of the remote side of the TDP trunk. This is the logical interface number of remote TDP interface used by the Tag Switch Controller (TSC). Common Name: Remote Logical Interface Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfRemoteNodeId 3.1.637.3.1.5.22.2.1.23
This entry represents the node ID of the remote side HSS node of the TDP trunk. Common Name: Remote Node ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnRoutingID  

adnTdpIfPolicingState 3.1.637.3.1.5.22.2.1.24
Indicates whether traffic policing is performed on this TDP interface. When policing is disabled then no traffic spacing will be done at the TDP interface no matter what the value of adnCvsiSpacingState is. Common Name: Policing
Status: mandatory Access: read-write
OBJECT-TYPE    
  AdnEnableDisabled  

adnTdpIfPCR 3.1.637.3.1.5.22.2.1.25
The Peak Cell Rate (PCR) allowed for traffic through this interface. This rate is specified in cells per second. Common Name: PCR
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfABW 3.1.637.3.1.5.22.2.1.26
The bandwidth, measured in cells per second, allocated to this TDP interface. Common Name: Allocated Bandwidth
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfRemNodeMacNum 3.1.637.3.1.5.22.2.1.27
The machine number part of adnTdpIfRemoteNodeId.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfRemNodeAreaNum 3.1.637.3.1.5.22.2.1.28
The area number part of adnTdpIfRemoteNodeId.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnTdpIfLookupTable 3.1.637.3.1.5.22.3
This table is a lookup table where a CVSI logical interface number is mapped to the corresponding ATM logical interface ifIndex. The ATM logical interface ifIndex is the index of the adnTdpIfTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnTdpIfLookupEntry

adnTdpIfLookupEntry 3.1.637.3.1.5.22.3.1
An entry in the TDP Interface lookup Table. There is one entry per TDP interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnTdpIfLookupEntry  

adnTdpIfIndex 3.1.637.3.1.5.22.3.1.1
The ATM logical interface ifIndex corresponding to the given logical interface number. This ifIndex is the index of the adnTdpIfTable. Common Name: IfIndex
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnAtmTdpConnTable 3.1.637.3.1.5.22.4
This table describes the TDP connections in the HSS. There is one entry per TDP connection in the HSS.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnAtmTdpConnEntry

adnAtmTdpConnEntry 3.1.637.3.1.5.22.4.1
An entry in the CVSI HSS Connection Table. There is one entry per TDP connection in the HSS.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnAtmTdpConnEntry  

adnAtmTdpConnVpi 3.1.637.3.1.5.22.4.1.1
The VPI of the ATM cross connection for this TDP connection. This is also an index of the table. Common Name: VPI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmTdpConnVci 3.1.637.3.1.5.22.4.1.2
The VCI of the ATM cross connection for this TDP connection. This is also an index of the table. Common Name: VCI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmTdpConnCconnectIndex 3.1.637.3.1.5.22.4.1.3
The index of the cross-connection for the Virtual Channel Connection (VCC) on this interface. In a point-to-point cross-connection, the index equals zero. In a point-to- -multipoint cross-connection, there is a different index for each leaf. Common Name: Cross Connect Index
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmTdpConnPriSec 3.1.637.3.1.5.22.4.1.4
This object tells whether this end of the TDP connection index is Primary or Secondary. Common Name: Pri/Sec
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

adnAtmTdpConnOutIfIndex 3.1.637.3.1.5.22.4.1.5
The ifIndex of this node's output ATM logical interface. Common Name: Out IfIndex
Status: mandatory Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

adnAtmTdpConnOutVpi 3.1.637.3.1.5.22.4.1.6
The Virtual Path Identifier (VPI) of this connection on the output ATM interface from this node. In conjunction with adnAtmTdpConnOutIfIndex, this VPI can be used for path tracing. Common Name: Out VPI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmTdpConnOutVci 3.1.637.3.1.5.22.4.1.7
The Virtual Connection Identifier (VCI) of this connection on the output ATM interface from this node. In conjunction with adnAtmTdpConnOutIfIndex, this VCI can be used for path tracing. Common Name: Out VCI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmTdpConnOutCconnectIndex 3.1.637.3.1.5.22.4.1.8
The index of the cross-connection for the Virtual Channel Connection (VCC) on the output ATM interface from this node. In a point-to-point cross-connection, the index equals zero. In a point-to-multipoint cross-connection, there is a different index for each leaf. Common Name: Out Cross Connect Index
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

adnAtmTdpConnState 3.1.637.3.1.5.22.4.1.9
This object provides the state of the connection The following are the possible values it can hold. 1 - Connection Reserved- Created but not activated 2 - Connection Active - Active state Common Name: Conn State
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER reserved(1), active(2)  

adnAtmTdpConnForwCellRate 3.1.637.3.1.5.22.4.1.10
The forward requested cell rate for this connection. This value is configured when the connection is created. Forward direction is the direction traffic from the primary to the secondary interface. A value of -1 indicates that the field is not used. Common Name: Forward Cell Rate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnForwPCR 3.1.637.3.1.5.22.4.1.11
The forward peak cell rate (PCR) for the connection. This value is configured when the connection is created. Forward direction is the direction traffic from the primary to the secondary interface. A value of -1 indicates that the field is not used. Common Name: Forward PCR
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnForwDelay 3.1.637.3.1.5.22.4.1.12
The maximum forward delay allowed for this connection. This value is configured when the connection is created. Forward direction is the direction traffic from the primary to the secondary interface. A value of -1 indicates that the field is not used. Common Name: Forward Delay
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnForwDelayVariation 3.1.637.3.1.5.22.4.1.13
The maximum Cell Delay Variation (CDV) in the forward direction allowed for this connection. This value is configured when the connection is created. Forward direction is the direction traffic from the primary to the secondary interface. A value of -1 indicates that the field is not used. Common Name: Forward CDV
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnRevCellRate 3.1.637.3.1.5.22.4.1.14
The reverse requested cell rate for this connection. This value is configured when the connection is created. Reverse direction is the direction of traffic from the secondary to the primary interface. A value of -1 indicates that the field is not used. Common Name: Reverse Cell Rate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnRevPCR 3.1.637.3.1.5.22.4.1.15
The reverse peak cell rate (PCR) for this connection. This value is configured when the connection is created. Reverse direction is the direction of traffic from the secondary to the primary interface. A value of -1 indicates that the field is not used. Common Name: Reverse PCR
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnRevDelay 3.1.637.3.1.5.22.4.1.16
The maximum reverse delay allowed for this connection. This value is configured when the connection is created. Reverse direction is the direction of traffic from the secondary to the primary interface. A value of -1 indicates that the field is not used. Common Name: Reverse Delay
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnRevDelayVariation 3.1.637.3.1.5.22.4.1.17
The maximum Cell Delay Variation (CDV) in the reverse direction allowed for this connection. This value is configured when the connection is created. Reverse direction is the direction of traffic from the secondary to the primary interface. A value of -1 indicates that the field is not used. Common Name: Reverse CDV
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnPriPersEPFlag 3.1.637.3.1.5.22.4.1.18
This object reflects the primary Persistent End point flag. This flag indicates that this part of connection is the first leg of a tag distribution protocol (TDP) connection. The first leg of the connection terminates at a tag edge router (TER). Common Name: Primary Endpoint Flag
Status: mandatory Access: read-only
OBJECT-TYPE    
  TruthValue  

adnAtmTdpConnSecPersEPFlag 3.1.637.3.1.5.22.4.1.19
This object reflects the secondary Persistent End point flag. This flag indicates that this part of connection is last leg of a tag distribution protocol (TDP) connection. The last leg of the connection terminates into a tag edge router (TER). Common Name: Secondry Endpoint Flag
Status: mandatory Access: read-only
OBJECT-TYPE    
  TruthValue  

adnAtmTdpConnForwSCR 3.1.637.3.1.5.22.4.1.20
The forward sustainable cell rate (SCR) for this connection. Forward direction is the direction traffic from the primary to the secondary interface. A value of -1 indicates that the field is not used. Common Name: Forward SCR
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnForwMBS 3.1.637.3.1.5.22.4.1.21
The forward maximum burst size (MBS) for this connection. Forward direction is the direction of traffic from the primary to the secondary interface. A value of -1 indicates that the field is not used. Common Name: Forward MBS
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnRevSCR 3.1.637.3.1.5.22.4.1.22
The Reverse sustainable cell rate (SCR) for this connection. Reverse direction is the direction traffic from the secondary to the primary interface. A value of -1 indicates that the field is not used. Common Name: Reverse SCR
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnRevMBS 3.1.637.3.1.5.22.4.1.23
The reverse maximum burst size (MBS) for this connection. Reverse direction is the direction of traffic from the secondary to the primary interface. A value of -1 indicates that the field is not used. Common Name: Reverse MBS
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnAtmTdpConnForwServType 3.1.637.3.1.5.22.4.1.24
The forward service type for a connection. It is a value which specifies what class of service has been requested for this connection in forward direction. Forward direction is the direction traffic from the primary to the secondary interface. Common Name: Forward Service Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnCvsiCos  

adnAtmTdpConnRevServType 3.1.637.3.1.5.22.4.1.25
The reverse service type for a connection. It is a value which specifies what class of service has been requested for this connection in reverse direction. Reverse direction is the direction of traffic from the secondary to the primary interface. Common Name: Reverse Service Type
Status: mandatory Access: read-only
OBJECT-TYPE    
  AdnCvsiCos  

adnIprtMIB 3.1.637.3.1.5.23
OBJECT IDENTIFIER    

adnIpRouteNodeTable 3.1.637.3.1.5.23.1
This is the IP Routing Configuration Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdnIpRouteNodeEntry

adnIpRouteNodeEntry 3.1.637.3.1.5.23.1.1
The IP Route Node Entry defines IP Routing Node Table Entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AdnIpRouteNodeEntry  

adnIpRouteConfigIndex 3.1.637.3.1.5.23.1.1.1
This object defines the Index into this table. This index will represent only one instance of any object in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER -2147483648..2147483647  

adnIpRouteConfigFilePtr 3.1.637.3.1.5.23.1.1.2
This object defines the pointer to an ASCII string that points to the IP routing Configuration path/file on the HSS CU disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

adnIpRouteConfigAdminState 3.1.637.3.1.5.23.1.1.3
This object indicates the desired state of the IP Routing (GateD) component. There are typically only two selection states, Enabled(1) or Disabled(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

adnIpRouteConfigOperState 3.1.637.3.1.5.23.1.1.4
This object indicates the current state of the IP Routing (GateD) component. There are typically only two states possible, Up(1) or Down(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor