ACD-FILTER-MIB

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
ACCEDIAN-SMI

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	IpAddress
Unsigned32	DisplayString	TruthValue
MacAddress	TEXTUAL-CONVENTION	RowStatus
MODULE-COMPLIANCE	OBJECT-GROUP	acdMibs

Defined Types

AcdFilterOperator
Operator for field comparaison. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
TEXTUAL-CONVENTION
	INTEGER	lessThan(1), greaterThan(2), equalTo(3), range(4)

AcdFilterVlanType
.
TEXTUAL-CONVENTION
	INTEGER	cvlan(1), svlan(2), both(3)

AcdL2FilterEntry
SEQUENCE
	acdL2FilterID	Unsigned32
	acdL2FilterName	DisplayString
	acdL2FilterMacDstEn	TruthValue
	acdL2FilterMacDst	MacAddress
	acdL2FilterMacDstMask	Unsigned32
	acdL2FilterMacSrcEn	TruthValue
	acdL2FilterMacSrc	MacAddress
	acdL2FilterMacSrcMask	Unsigned32
	acdL2FilterEtypeEn	TruthValue
	acdL2FilterEtype	Unsigned32
	acdL2FilterVlan1PriorEn	TruthValue
	acdL2FilterVlan1Prior	Unsigned32
	acdL2FilterVlan1CfiEn	TruthValue
	acdL2FilterVlan1Cfi	Unsigned32
	acdL2FilterVlan1IdEn	TruthValue
	acdL2FilterVlan1Id	Unsigned32
	acdL2FilterVlan2PriorEn	TruthValue
	acdL2FilterVlan2Prior	Unsigned32
	acdL2FilterVlan2CfiEn	TruthValue
	acdL2FilterVlan2Cfi	Unsigned32
	acdL2FilterVlan2IdEn	TruthValue
	acdL2FilterVlan2Id	Unsigned32
	acdL2FilterRowStatus	RowStatus

AcdIPv4FilterEntry
SEQUENCE
	acdIPv4FilterID	Unsigned32
	acdIPv4FilterName	DisplayString
	acdIPv4FilterSrcEn	TruthValue
	acdIPv4FilterSrc	IpAddress
	acdIPv4FilterSrcMask	IpAddress
	acdIPv4FilterDstEn	TruthValue
	acdIPv4FilterDst	IpAddress
	acdIPv4FilterDstMask	IpAddress
	acdIPv4FilterProtoEn	TruthValue
	acdIPv4FilterProto	Unsigned32
	acdIPv4FilterTTLEn	TruthValue
	acdIPv4FilterTTL	Unsigned32
	acdIPv4FilterIHLEn	TruthValue
	acdIPv4FilterIHL	Unsigned32
	acdIPv4FilterDscpEn	TruthValue
	acdIPv4FilterDscp	Unsigned32
	acdIPv4FilterECNEn	TruthValue
	acdIPv4FilterECN	Unsigned32
	acdIPv4FilterSrcPortEn	TruthValue
	acdIPv4FilterSrcPort	Unsigned32
	acdIPv4FilterDstPortEn	TruthValue
	acdIPv4FilterDstPort	Unsigned32
	acdIPv4FilterIcmpTypeEn	TruthValue
	acdIPv4FilterIcmpType	Unsigned32
	acdIPv4FilterIcmpCodeEn	TruthValue
	acdIPv4FilterIcmpCode	Unsigned32
	acdIPv4FilterRowStatus	RowStatus

AcdSmapL2FilterEntry
SEQUENCE
	acdSmapL2FilterID	Unsigned32
	acdSmapL2FilterName	DisplayString
	acdSmapL2FilterRowStatus	RowStatus
	acdSmapL2FilterVlan1PriorEn	TruthValue
	acdSmapL2FilterVlan1Prior	Unsigned32
	acdSmapL2FilterVlan1PriorLast	Unsigned32
	acdSmapL2FilterVlan1PriorOper	AcdFilterOperator
	acdSmapL2FilterVlan1IdEn	TruthValue
	acdSmapL2FilterVlan1Id	Unsigned32
	acdSmapL2FilterVlan1IdLast	Unsigned32
	acdSmapL2FilterVlan1IdOper	AcdFilterOperator
	acdSmapL2FilterVlan1CfiEn	TruthValue
	acdSmapL2FilterVlan1Cfi	Unsigned32
	acdSmapL2FilterVlan1TypeEn	TruthValue
	acdSmapL2FilterVlan1Type	AcdFilterVlanType
	acdSmapL2FilterVlan2PriorEn	TruthValue
	acdSmapL2FilterVlan2Prior	Unsigned32
	acdSmapL2FilterVlan2PriorLast	Unsigned32
	acdSmapL2FilterVlan2PriorOper	AcdFilterOperator
	acdSmapL2FilterVlan2IdEn	TruthValue
	acdSmapL2FilterVlan2Id	Unsigned32
	acdSmapL2FilterVlan2IdLast	Unsigned32
	acdSmapL2FilterVlan2IdOper	AcdFilterOperator
	acdSmapL2FilterVlan2CfiEn	TruthValue
	acdSmapL2FilterVlan2Cfi	Unsigned32
	acdSmapL2FilterVlan2TypeEn	TruthValue
	acdSmapL2FilterVlan2Type	AcdFilterVlanType
	acdSmapL2FilterMacDstEn	TruthValue
	acdSmapL2FilterMacDst	MacAddress
	acdSmapL2FilterMacDstMask	Unsigned32
	acdSmapL2FilterMacSrcEn	TruthValue
	acdSmapL2FilterMacSrc	MacAddress
	acdSmapL2FilterMacSrcMask	Unsigned32
	acdSmapL2FilterEtypeEn	TruthValue
	acdSmapL2FilterEtype	Unsigned32
	acdSmapL2FilterIpCosEn	TruthValue
	acdSmapL2FilterIpCosMode	INTEGER
	acdSmapL2FilterDscp	Unsigned32
	acdSmapL2FilterDscpLast	Unsigned32
	acdSmapL2FilterDscpOper	AcdFilterOperator
	acdSmapL2FilterPre	Unsigned32
	acdSmapL2FilterPreLast	Unsigned32
	acdSmapL2FilterPreOper	AcdFilterOperator

AcdSmapIPv4FilterEntry
SEQUENCE
	acdSmapIPv4FilterID	Unsigned32
	acdSmapIPv4FilterName	DisplayString
	acdSmapIPv4FilterRowStatus	RowStatus
	acdSmapIPv4FilterVlan1PriorEn	TruthValue
	acdSmapIPv4FilterVlan1Prior	Unsigned32
	acdSmapIPv4FilterVlan1PriorLast	Unsigned32
	acdSmapIPv4FilterVlan1PriorOper	AcdFilterOperator
	acdSmapIPv4FilterVlan1IdEn	TruthValue
	acdSmapIPv4FilterVlan1Id	Unsigned32
	acdSmapIPv4FilterVlan1IdLast	Unsigned32
	acdSmapIPv4FilterVlan1IdOper	AcdFilterOperator
	acdSmapIPv4FilterVlan1CfiEn	TruthValue
	acdSmapIPv4FilterVlan1Cfi	Unsigned32
	acdSmapIPv4FilterVlan1TypeEn	TruthValue
	acdSmapIPv4FilterVlan1Type	AcdFilterVlanType
	acdSmapIPv4FilterVlan2PriorEn	TruthValue
	acdSmapIPv4FilterVlan2Prior	Unsigned32
	acdSmapIPv4FilterVlan2PriorLast	Unsigned32
	acdSmapIPv4FilterVlan2PriorOper	AcdFilterOperator
	acdSmapIPv4FilterVlan2IdEn	TruthValue
	acdSmapIPv4FilterVlan2Id	Unsigned32
	acdSmapIPv4FilterVlan2IdLast	Unsigned32
	acdSmapIPv4FilterVlan2IdOper	AcdFilterOperator
	acdSmapIPv4FilterVlan2CfiEn	TruthValue
	acdSmapIPv4FilterVlan2Cfi	Unsigned32
	acdSmapIPv4FilterVlan2TypeEn	TruthValue
	acdSmapIPv4FilterVlan2Type	AcdFilterVlanType
	acdSmapIPv4FilterSrcEn	TruthValue
	acdSmapIPv4FilterSrc	IpAddress
	acdSmapIPv4FilterSrcMask	IpAddress
	acdSmapIPv4FilterDstEn	TruthValue
	acdSmapIPv4FilterDst	IpAddress
	acdSmapIPv4FilterDstMask	IpAddress
	acdSmapIPv4FilterProtoEn	TruthValue
	acdSmapIPv4FilterProto	Unsigned32
	acdSmapIPv4FilterTTLEn	TruthValue
	acdSmapIPv4FilterTTL	Unsigned32
	acdSmapIPv4FilterIHLEn	TruthValue
	acdSmapIPv4FilterIHL	Unsigned32
	acdSmapIPv4FilterIpCosEn	TruthValue
	acdSmapIPv4FilterIpCosMode	INTEGER
	acdSmapIPv4FilterDscp	Unsigned32
	acdSmapIPv4FilterDscpLast	Unsigned32
	acdSmapIPv4FilterDscpOper	AcdFilterOperator
	acdSmapIPv4FilterPre	Unsigned32
	acdSmapIPv4FilterPreLast	Unsigned32
	acdSmapIPv4FilterPreOper	AcdFilterOperator
	acdSmapIPv4FilterECNEn	TruthValue
	acdSmapIPv4FilterECN	Unsigned32
	acdSmapIPv4FilterSrcPortEn	TruthValue
	acdSmapIPv4FilterSrcPort	Unsigned32
	acdSmapIPv4FilterDstPortEn	TruthValue
	acdSmapIPv4FilterDstPort	Unsigned32
	acdSmapIPv4FilterIcmpTypeEn	TruthValue
	acdSmapIPv4FilterIcmpType	Unsigned32
	acdSmapIPv4FilterIcmpCodeEn	TruthValue
	acdSmapIPv4FilterIcmpCode	Unsigned32

Defined Values

acdFilter		1.3.6.1.4.1.22420.2.2
The Filter database for this Accedian Networks device.
MODULE-IDENTITY

acdFilterNotifications		1.3.6.1.4.1.22420.2.2.5
OBJECT IDENTIFIER

acdFilterMIBObjects		1.3.6.1.4.1.22420.2.2.6
OBJECT IDENTIFIER

acdFilterConformance		1.3.6.1.4.1.22420.2.2.7
OBJECT IDENTIFIER

acdFilterTableTid		1.3.6.1.4.1.22420.2.2.6.1
OBJECT IDENTIFIER

acdL2FilterTable		1.3.6.1.4.1.22420.2.2.1
Table of all Layer 2 filters
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AcdL2FilterEntry

acdL2FilterEntry		1.3.6.1.4.1.22420.2.2.1.1
A Filter is a pattern matching a definition against packets.
Status: current	Access: not-accessible
OBJECT-TYPE
	AcdL2FilterEntry

acdL2FilterID		1.3.6.1.4.1.22420.2.2.1.1.1
Unique value for each filter. Its value ranges from 1 to maximum value. This maximum value depend of the type of platform.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

acdL2FilterName		1.3.6.1.4.1.22420.2.2.1.1.2
This is a string to identify the filter.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..31)

acdL2FilterMacDstEn		1.3.6.1.4.1.22420.2.2.1.1.3
Enable or disable the destination MAC address check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdL2FilterMacDst		1.3.6.1.4.1.22420.2.2.1.1.4
The destination MAC address used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

acdL2FilterMacDstMask		1.3.6.1.4.1.22420.2.2.1.1.5
Number of destination MAC address bits to compare. Its value ranges from 0 to 48. Only specific mask are valid per platform.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..48

acdL2FilterMacSrcEn		1.3.6.1.4.1.22420.2.2.1.1.6
Enable or disable the source MAC address check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdL2FilterMacSrc		1.3.6.1.4.1.22420.2.2.1.1.7
The source MAC address used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

acdL2FilterMacSrcMask		1.3.6.1.4.1.22420.2.2.1.1.8
Number of source MAC address bits to compare. Its value ranges from 0 to 48. Only specific mask are valid per platform.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..48

acdL2FilterEtypeEn		1.3.6.1.4.1.22420.2.2.1.1.9
Enable or disable the Ethernet type check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdL2FilterEtype		1.3.6.1.4.1.22420.2.2.1.1.10
The Ethernet type used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

acdL2FilterVlan1PriorEn		1.3.6.1.4.1.22420.2.2.1.1.11
Enable or disable the first VLAN priority check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdL2FilterVlan1Prior		1.3.6.1.4.1.22420.2.2.1.1.12
The first VLAN priority used to compare the incoming traffic. Its value ranges from 0 to 7.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdL2FilterVlan1CfiEn		1.3.6.1.4.1.22420.2.2.1.1.13
Enable or disable the first VLAN CFI check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdL2FilterVlan1Cfi		1.3.6.1.4.1.22420.2.2.1.1.14
The first VLAN CFI used to compare the incoming traffic. Its value is 0 or 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1

acdL2FilterVlan1IdEn		1.3.6.1.4.1.22420.2.2.1.1.15
Enable or disable the first VLAN ID check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdL2FilterVlan1Id		1.3.6.1.4.1.22420.2.2.1.1.16
The first VLAN ID used to compare the incoming traffic. Its value ranges from 0 to 4095.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4095

acdL2FilterVlan2PriorEn		1.3.6.1.4.1.22420.2.2.1.1.17
Enable or disable the second VLAN priority check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdL2FilterVlan2Prior		1.3.6.1.4.1.22420.2.2.1.1.18
The second VLAN priority used to compare the incoming traffic. Its value ranges from 0 to 7.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdL2FilterVlan2CfiEn		1.3.6.1.4.1.22420.2.2.1.1.19
Enable or disable the second VLAN CFI check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdL2FilterVlan2Cfi		1.3.6.1.4.1.22420.2.2.1.1.20
The second VLAN CFI used to compare the incoming traffic. Its value is 0 or 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1

acdL2FilterVlan2IdEn		1.3.6.1.4.1.22420.2.2.1.1.21
Enable or disable the second VLAN ID check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdL2FilterVlan2Id		1.3.6.1.4.1.22420.2.2.1.1.22
The second VLAN ID used to compare the incoming traffic. Its value ranges from 0 to 4095.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4065

acdL2FilterRowStatus		1.3.6.1.4.1.22420.2.2.1.1.23
All columns must have a valid value before a row can be activated. To create a new filter you shall provide the a unique filter name for an empty row with the RowStatus set to Create and Go. To delete the row you need to set the RowStatus to destroy.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

acdIPv4FilterTable		1.3.6.1.4.1.22420.2.2.2
Table of all IPv4 filters
Status: deprecated	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AcdIPv4FilterEntry

acdIPv4FilterEntry		1.3.6.1.4.1.22420.2.2.2.1
A Filter is a pattern matching a definition against packets.
Status: current	Access: not-accessible
OBJECT-TYPE
	AcdIPv4FilterEntry

acdIPv4FilterID		1.3.6.1.4.1.22420.2.2.2.1.1
Unique value for each filter. Its value ranges from 1 to maximum value. This maximum value depend of the type of platform.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

acdIPv4FilterName		1.3.6.1.4.1.22420.2.2.2.1.2
This is a string to identify the filter.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..31)

acdIPv4FilterSrcEn		1.3.6.1.4.1.22420.2.2.2.1.3
Enable or disable the Source IP address check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterSrc		1.3.6.1.4.1.22420.2.2.2.1.4
The source IP address used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

acdIPv4FilterSrcMask		1.3.6.1.4.1.22420.2.2.2.1.5
The source IP address mask used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

acdIPv4FilterDstEn		1.3.6.1.4.1.22420.2.2.2.1.6
Enable or disable the Destination IP address check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterDst		1.3.6.1.4.1.22420.2.2.2.1.7
The destination IP address used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

acdIPv4FilterDstMask		1.3.6.1.4.1.22420.2.2.2.1.8
The destination IP address mask used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

acdIPv4FilterProtoEn		1.3.6.1.4.1.22420.2.2.2.1.9
Enable or disable the IP protocol check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterProto		1.3.6.1.4.1.22420.2.2.2.1.10
The IP protocol used to compare the incoming traffic. Its value ranges from 0 to 255.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

acdIPv4FilterTTLEn		1.3.6.1.4.1.22420.2.2.2.1.11
Enable or disable the TTL check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterTTL		1.3.6.1.4.1.22420.2.2.2.1.12
The TTL used to compare the incoming traffic. Its value ranges from 0 to 255.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

acdIPv4FilterIHLEn		1.3.6.1.4.1.22420.2.2.2.1.13
Enable or disable the IP Header Length check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterIHL		1.3.6.1.4.1.22420.2.2.2.1.14
The IP Header Length used to compare the incoming traffic. Its value ranges from 5 to 15.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	5..15

acdIPv4FilterDscpEn		1.3.6.1.4.1.22420.2.2.2.1.15
Enable or disable the DSCP (Diff-Serv Code Point) check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterDscp		1.3.6.1.4.1.22420.2.2.2.1.16
The DSCP value used to compare the incoming traffic. Its value ranges from 0 to 63.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..63

acdIPv4FilterECNEn		1.3.6.1.4.1.22420.2.2.2.1.17
Enable or disable the ECN (Explicite Cogestion Notification) check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterECN		1.3.6.1.4.1.22420.2.2.2.1.18
The ECN value used to compare the incoming traffic. Its value ranges from 0 to 3.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..3

acdIPv4FilterSrcPortEn		1.3.6.1.4.1.22420.2.2.2.1.19
Enable or disable the UDP/TCP Source port check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterSrcPort		1.3.6.1.4.1.22420.2.2.2.1.20
The UDP/TCP Source Port used to compare the incoming traffic. Its value ranges from 0 to 65535.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

acdIPv4FilterDstPortEn		1.3.6.1.4.1.22420.2.2.2.1.21
Enable or disable the UDP/TCP Destination port check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterDstPort		1.3.6.1.4.1.22420.2.2.2.1.22
The UDP/TCP Destination Port used to compare the incoming traffic. Its value ranges from 0 to 65535.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

acdIPv4FilterIcmpTypeEn		1.3.6.1.4.1.22420.2.2.2.1.23
Enable or disable the ICMP type check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterIcmpType		1.3.6.1.4.1.22420.2.2.2.1.24
The ICMP type used to compare the incoming traffic. Its value ranges from 0 to 255.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

acdIPv4FilterIcmpCodeEn		1.3.6.1.4.1.22420.2.2.2.1.25
Enable or disable the ICMP code check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdIPv4FilterIcmpCode		1.3.6.1.4.1.22420.2.2.2.1.26
The ICMP code used to compare the incoming traffic. Its value ranges from 0 to 255.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

acdIPv4FilterRowStatus		1.3.6.1.4.1.22420.2.2.2.1.27
All columns must have a valid value before a row can be activated. To create a new filter you shall provide the a unique filter name for an empty row with the RowStatus set to Create and Go. To delete the row you need to set the RowStatus to destroy.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

acdSmapL2FilterTable		1.3.6.1.4.1.22420.2.2.3
Table of all service mapping (SMAP) Layer 2 filters
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AcdSmapL2FilterEntry

acdSmapL2FilterEntry		1.3.6.1.4.1.22420.2.2.3.1
A Filter is a pattern matching a definition against packets.
Status: current	Access: not-accessible
OBJECT-TYPE
	AcdSmapL2FilterEntry

acdSmapL2FilterID		1.3.6.1.4.1.22420.2.2.3.1.1
Unique value for each filter. Its value ranges from 1 to maximum value. This maximum value depend of the type of platform.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

acdSmapL2FilterName		1.3.6.1.4.1.22420.2.2.3.1.2
This is a string to identify the filter.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..31)

acdSmapL2FilterRowStatus		1.3.6.1.4.1.22420.2.2.3.1.3
All columns must have a valid value before a row can be activated. To create a new filter you shall provide the a unique filter name for an empty row with the RowStatus set to Create and Go. To delete the row you need to set the RowStatus to destroy.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

acdSmapL2FilterVlan1PriorEn		1.3.6.1.4.1.22420.2.2.3.1.4
Enable or disable the first VLAN priority check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterVlan1Prior		1.3.6.1.4.1.22420.2.2.3.1.5
The first VLAN priority used to compare the incoming traffic. Its value ranges from 0 to 7.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapL2FilterVlan1PriorLast		1.3.6.1.4.1.22420.2.2.3.1.6
First VLAN priority last value, used in range operation. Its value ranges from 0 to 7.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapL2FilterVlan1PriorOper		1.3.6.1.4.1.22420.2.2.3.1.7
First VLAN Priority operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapL2FilterVlan1IdEn		1.3.6.1.4.1.22420.2.2.3.1.8
Enable or disable the first VLAN ID check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterVlan1Id		1.3.6.1.4.1.22420.2.2.3.1.9
The first VLAN ID used to compare the incoming traffic. Its value ranges from 0 to 4095.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4095

acdSmapL2FilterVlan1IdLast		1.3.6.1.4.1.22420.2.2.3.1.10
First VLAN ID last value, used in range operation. Its value ranges from 0 to 4095.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4095

acdSmapL2FilterVlan1IdOper		1.3.6.1.4.1.22420.2.2.3.1.11
First VLAN ID operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapL2FilterVlan1CfiEn		1.3.6.1.4.1.22420.2.2.3.1.12
Enable or disable the first VLAN CFI check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterVlan1Cfi		1.3.6.1.4.1.22420.2.2.3.1.13
The first VLAN CFI used to compare the incoming traffic. Its value is 0 or 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1

acdSmapL2FilterVlan1TypeEn		1.3.6.1.4.1.22420.2.2.3.1.14
Enable or disable the first VLAN Ethertype check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterVlan1Type		1.3.6.1.4.1.22420.2.2.3.1.15
VLAN Ethernet type.
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterVlanType

acdSmapL2FilterVlan2PriorEn		1.3.6.1.4.1.22420.2.2.3.1.16
Enable or disable the second VLAN priority check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterVlan2Prior		1.3.6.1.4.1.22420.2.2.3.1.17
The second VLAN priority used to compare the incoming traffic. Its value ranges from 0 to 7.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapL2FilterVlan2PriorLast		1.3.6.1.4.1.22420.2.2.3.1.18
Second VLAN priority last value, used in range operation. Its value ranges from 0 to 7.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapL2FilterVlan2PriorOper		1.3.6.1.4.1.22420.2.2.3.1.19
VLAN Priority operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapL2FilterVlan2IdEn		1.3.6.1.4.1.22420.2.2.3.1.20
Enable or disable the second VLAN ID check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterVlan2Id		1.3.6.1.4.1.22420.2.2.3.1.21
The second VLAN ID used to compare the incoming traffic. Its value ranges from 0 to 4095.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4095

acdSmapL2FilterVlan2IdLast		1.3.6.1.4.1.22420.2.2.3.1.22
Second VLAN ID last value, used in range operation. Its value ranges from 0 to 4095.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4095

acdSmapL2FilterVlan2IdOper		1.3.6.1.4.1.22420.2.2.3.1.23
Second VLAN ID operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapL2FilterVlan2CfiEn		1.3.6.1.4.1.22420.2.2.3.1.24
Enable or disable the second VLAN CFI check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterVlan2Cfi		1.3.6.1.4.1.22420.2.2.3.1.25
The second VLAN CFI used to compare the incoming traffic. Its value is 0 or 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1

acdSmapL2FilterVlan2TypeEn		1.3.6.1.4.1.22420.2.2.3.1.26
Enable or disable the second VLAN Ethertype check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterVlan2Type		1.3.6.1.4.1.22420.2.2.3.1.27
VLAN Ethernet type.
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterVlanType

acdSmapL2FilterMacDstEn		1.3.6.1.4.1.22420.2.2.3.1.28
Enable or disable the destination MAC address check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterMacDst		1.3.6.1.4.1.22420.2.2.3.1.29
The destination MAC address used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

acdSmapL2FilterMacDstMask		1.3.6.1.4.1.22420.2.2.3.1.30
Number of destination MAC address bits to compare. Its value ranges from 0 to 48.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

acdSmapL2FilterMacSrcEn		1.3.6.1.4.1.22420.2.2.3.1.31
Enable or disable the source MAC address check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterMacSrc		1.3.6.1.4.1.22420.2.2.3.1.32
The source MAC address used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	MacAddress

acdSmapL2FilterMacSrcMask		1.3.6.1.4.1.22420.2.2.3.1.33
Number of source MAC address bits to compare. Its value ranges from 0 to 48.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

acdSmapL2FilterEtypeEn		1.3.6.1.4.1.22420.2.2.3.1.34
Enable or disable the Ethernet type check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterEtype		1.3.6.1.4.1.22420.2.2.3.1.35
The Ethernet type used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

acdSmapL2FilterIpCosEn		1.3.6.1.4.1.22420.2.2.3.1.36
Enable or disable the Ethernet type check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapL2FilterIpCosMode		1.3.6.1.4.1.22420.2.2.3.1.37
VLAN ID operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	dscp(1), pre(2)

acdSmapL2FilterDscp		1.3.6.1.4.1.22420.2.2.3.1.38
The DSCP value used to compare the incoming traffic. Its value ranges from 0 to 63.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..63

acdSmapL2FilterDscpLast		1.3.6.1.4.1.22420.2.2.3.1.39
The last DSCP value, used in range operation. Its value ranges from 0 to 63.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..63

acdSmapL2FilterDscpOper		1.3.6.1.4.1.22420.2.2.3.1.40
DSCP operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapL2FilterPre		1.3.6.1.4.1.22420.2.2.3.1.41
The Precedence value used to compare the incoming traffic. Its value ranges from 0 to 3.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapL2FilterPreLast		1.3.6.1.4.1.22420.2.2.3.1.42
The last Precedence value, used in range operation. Its value ranges from 0 to 3.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapL2FilterPreOper		1.3.6.1.4.1.22420.2.2.3.1.43
Precedence operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapIPv4FilterTable		1.3.6.1.4.1.22420.2.2.4
Table of all Extended IPv4 filters
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		AcdSmapIPv4FilterEntry

acdSmapIPv4FilterEntry		1.3.6.1.4.1.22420.2.2.4.1
A Filter is a pattern matching a definition against packets.
Status: current	Access: not-accessible
OBJECT-TYPE
	AcdSmapIPv4FilterEntry

acdSmapIPv4FilterID		1.3.6.1.4.1.22420.2.2.4.1.1
Unique value for each filter. Its value ranges from 1 to maximum value. This maximum value depend of the type of platform.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

acdSmapIPv4FilterName		1.3.6.1.4.1.22420.2.2.4.1.2
This is a string to identify the filter.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(1..31)

acdSmapIPv4FilterRowStatus		1.3.6.1.4.1.22420.2.2.4.1.3
All columns must have a valid value before a row can be activated. To create a new filter you shall provide the a unique filter name for an empty row with the RowStatus set to Create and Go. To delete the row you need to set the RowStatus to destroy.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

acdSmapIPv4FilterVlan1PriorEn		1.3.6.1.4.1.22420.2.2.4.1.4
Enable or disable the first VLAN priority check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterVlan1Prior		1.3.6.1.4.1.22420.2.2.4.1.5
The first VLAN priority used to compare the incoming traffic. Its value ranges from 0 to 7.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapIPv4FilterVlan1PriorLast		1.3.6.1.4.1.22420.2.2.4.1.6
First VLAN priority last value, used in range operation. Its value ranges from 0 to 7.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapIPv4FilterVlan1PriorOper		1.3.6.1.4.1.22420.2.2.4.1.7
VLAN Priority operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapIPv4FilterVlan1IdEn		1.3.6.1.4.1.22420.2.2.4.1.8
Enable or disable the first VLAN ID check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterVlan1Id		1.3.6.1.4.1.22420.2.2.4.1.9
The first VLAN ID used to compare the incoming traffic. Its value ranges from 0 to 4095.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4095

acdSmapIPv4FilterVlan1IdLast		1.3.6.1.4.1.22420.2.2.4.1.10
First VLAN ID last value, used in range operation. Its value ranges from 0 to 4095.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4095

acdSmapIPv4FilterVlan1IdOper		1.3.6.1.4.1.22420.2.2.4.1.11
First VLAN ID operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapIPv4FilterVlan1CfiEn		1.3.6.1.4.1.22420.2.2.4.1.12
Enable or disable the first VLAN CFI check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterVlan1Cfi		1.3.6.1.4.1.22420.2.2.4.1.13
The first VLAN CFI used to compare the incoming traffic. Its value is 0 or 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

acdSmapIPv4FilterVlan1TypeEn		1.3.6.1.4.1.22420.2.2.4.1.14
Enable or disable the first VLAN Ethertype check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterVlan1Type		1.3.6.1.4.1.22420.2.2.4.1.15
VLAN Ethernet type.
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterVlanType

acdSmapIPv4FilterVlan2PriorEn		1.3.6.1.4.1.22420.2.2.4.1.16
Enable or disable the second VLAN priority check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterVlan2Prior		1.3.6.1.4.1.22420.2.2.4.1.17
The second VLAN priority used to compare the incoming traffic. Its value ranges from 0 to 7.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapIPv4FilterVlan2PriorLast		1.3.6.1.4.1.22420.2.2.4.1.18
Second VLAN priority last value, used in range operation. Its value ranges from 0 to 7.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapIPv4FilterVlan2PriorOper		1.3.6.1.4.1.22420.2.2.4.1.19
VLAN Priority operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapIPv4FilterVlan2IdEn		1.3.6.1.4.1.22420.2.2.4.1.20
Enable or disable the second VLAN ID check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterVlan2Id		1.3.6.1.4.1.22420.2.2.4.1.21
The second VLAN ID used to compare the incoming traffic. Its value ranges from 0 to 4095.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4095

acdSmapIPv4FilterVlan2IdLast		1.3.6.1.4.1.22420.2.2.4.1.22
The second VLAN ID used to compare the incoming traffic. Its value ranges from 0 to 4095.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..4095

acdSmapIPv4FilterVlan2IdOper		1.3.6.1.4.1.22420.2.2.4.1.23
VLAN ID operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapIPv4FilterVlan2CfiEn		1.3.6.1.4.1.22420.2.2.4.1.24
Enable or disable the second VLAN CFI check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterVlan2Cfi		1.3.6.1.4.1.22420.2.2.4.1.25
The second VLAN CFI used to compare the incoming traffic. Its value is 0 or 1.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1

acdSmapIPv4FilterVlan2TypeEn		1.3.6.1.4.1.22420.2.2.4.1.26
Enable or disable the second VLAN Ethertype check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterVlan2Type		1.3.6.1.4.1.22420.2.2.4.1.27
VLAN Ethernet type.
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterVlanType

acdSmapIPv4FilterSrcEn		1.3.6.1.4.1.22420.2.2.4.1.28
Enable or disable the Source IP address check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterSrc		1.3.6.1.4.1.22420.2.2.4.1.29
The source IP address used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

acdSmapIPv4FilterSrcMask		1.3.6.1.4.1.22420.2.2.4.1.30
The source IP address mask used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

acdSmapIPv4FilterDstEn		1.3.6.1.4.1.22420.2.2.4.1.31
Enable or disable the Destination IP address check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterDst		1.3.6.1.4.1.22420.2.2.4.1.32
The destination IP address used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

acdSmapIPv4FilterDstMask		1.3.6.1.4.1.22420.2.2.4.1.33
The destination IP address mask used to compare the incoming traffic.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

acdSmapIPv4FilterProtoEn		1.3.6.1.4.1.22420.2.2.4.1.34
Enable or disable the IP protocol check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterProto		1.3.6.1.4.1.22420.2.2.4.1.35
The IP protocol used to compare the incoming traffic. Its value ranges from 0 to 255.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

acdSmapIPv4FilterTTLEn		1.3.6.1.4.1.22420.2.2.4.1.36
Enable or disable the TTL check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterTTL		1.3.6.1.4.1.22420.2.2.4.1.37
The TTL used to compare the incoming traffic. Its value ranges from 0 to 255.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

acdSmapIPv4FilterIHLEn		1.3.6.1.4.1.22420.2.2.4.1.38
Enable or disable the IP Header Length check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterIHL		1.3.6.1.4.1.22420.2.2.4.1.39
The IP Header Length used to compare the incoming traffic. Its value ranges from 5 to 15.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	5..15

acdSmapIPv4FilterIpCosEn		1.3.6.1.4.1.22420.2.2.4.1.40
Enable or disable the Ethernet type check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterIpCosMode		1.3.6.1.4.1.22420.2.2.4.1.41
VLAN ID operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	dscp(1), pre(2)

acdSmapIPv4FilterDscp		1.3.6.1.4.1.22420.2.2.4.1.42
The DSCP value used to compare the incoming traffic. Its value ranges from 0 to 63.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..63

acdSmapIPv4FilterDscpLast		1.3.6.1.4.1.22420.2.2.4.1.43
The DSCP value used to compare the incoming traffic. Its value ranges from 0 to 63.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..63

acdSmapIPv4FilterDscpOper		1.3.6.1.4.1.22420.2.2.4.1.44
DSCP operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapIPv4FilterPre		1.3.6.1.4.1.22420.2.2.4.1.45
The Precedence value used to compare the incoming traffic. Its value ranges from 0 to 3.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapIPv4FilterPreLast		1.3.6.1.4.1.22420.2.2.4.1.46
The Precedence value used to compare the incoming traffic. Its value ranges from 0 to 3.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..7

acdSmapIPv4FilterPreOper		1.3.6.1.4.1.22420.2.2.4.1.47
Precedence operator. Valid operator types are: Greater than, Less than, Equal to or Range (inclusive range).
Status: current	Access: read-create
OBJECT-TYPE
	AcdFilterOperator

acdSmapIPv4FilterECNEn		1.3.6.1.4.1.22420.2.2.4.1.48
Enable or disable the ECN (Explicite Cogestion Notification) check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterECN		1.3.6.1.4.1.22420.2.2.4.1.49
The ECN value used to compare the incoming traffic. Its value ranges from 0 to 3.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..3

acdSmapIPv4FilterSrcPortEn		1.3.6.1.4.1.22420.2.2.4.1.50
Enable or disable the UDP/TCP Source port check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterSrcPort		1.3.6.1.4.1.22420.2.2.4.1.51
The UDP/TCP Source Port used to compare the incoming traffic. Its value ranges from 0 to 65535.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

acdSmapIPv4FilterDstPortEn		1.3.6.1.4.1.22420.2.2.4.1.52
Enable or disable the UDP/TCP Destination port check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterDstPort		1.3.6.1.4.1.22420.2.2.4.1.53
The UDP/TCP Destination Port used to compare the incoming traffic. Its value ranges from 0 to 65535.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

acdSmapIPv4FilterIcmpTypeEn		1.3.6.1.4.1.22420.2.2.4.1.54
Enable or disable the ICMP type check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterIcmpType		1.3.6.1.4.1.22420.2.2.4.1.55
The ICMP type used to compare the incoming traffic. Its value ranges from 0 to 255.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

acdSmapIPv4FilterIcmpCodeEn		1.3.6.1.4.1.22420.2.2.4.1.56
Enable or disable the ICMP code check.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

acdSmapIPv4FilterIcmpCode		1.3.6.1.4.1.22420.2.2.4.1.57
The ICMP code used to compare the incoming traffic. Its value ranges from 0 to 255.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..255

acdSmapL2FilterTableLastChangeTid		1.3.6.1.4.1.22420.2.2.6.1.1
This is the transaction ID of the last change of the acdSmapL2FilterTable table. If this value is different since the last read this is indicate a table change.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

acdSmapIPv4FilterTableLastChangeTid		1.3.6.1.4.1.22420.2.2.6.1.2
This is the transaction ID of the last change of the acdSmapIPv4FilterTable table. If this value is different since the last read this is indicate a table change.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

acdFilterCompliances		1.3.6.1.4.1.22420.2.2.7.1
OBJECT IDENTIFIER

acdFilterGroups		1.3.6.1.4.1.22420.2.2.7.2
OBJECT IDENTIFIER

acdL2FilterGroup		1.3.6.1.4.1.22420.2.2.7.2.1
Objects for the L2 filter configuration Group.
Status: current	Access: read-only
OBJECT-GROUP

acdIPv4FilterGroup		1.3.6.1.4.1.22420.2.2.7.2.2
Objects for the IPv4 filter configuration Group.
Status: current	Access: read-only
OBJECT-GROUP

acdSmapL2FilterGroup		1.3.6.1.4.1.22420.2.2.7.2.3
Objects for the SMAP L2 filter configuration Group.
Status: current	Access: read-only
OBJECT-GROUP

acdSmapIPv4FilterGroup		1.3.6.1.4.1.22420.2.2.7.2.4
Objects for the SMAP IPv4 filter configuration Group.
Status: current	Access: read-only
OBJECT-GROUP

acdFilterTidGroup		1.3.6.1.4.1.22420.2.2.7.2.5
List of scalars to monitior changes in tables.
Status: current	Access: read-only
OBJECT-GROUP

acdFilterCompliance		1.3.6.1.4.1.22420.2.2.7.1.1
The compliance statement for support of the ACD-FILTER-MIB module.
Status: current	Access: read-only
MODULE-COMPLIANCE