ACC-PPP

File: ACC-PPP.mib (147919 bytes)

Imported modules

RFC1155-SMI RFC-1215 RFC1213-MIB
ACC-SYSTEM ACC-MULTILINK ACC-FAKE
ACC-MIB

Imported symbols

OBJECT-TYPE IpAddress TimeTicks
Gauge Counter TRAP-TYPE
ifIndex accTrapLogSeqNum accMlPppIndex
accMultilink ifOperStatus accBRG
DisplayString RowStatus IfIndex
SmdsAddress

Defined Types

AccPppLinkEntry  
SEQUENCE    
  accPppLinkIndex INTEGER
  accPppLinkPhysicalIndex INTEGER
  accPppLinkBadAddresses Counter
  accPppLinkBadControls Counter
  accPppLinkPacketTooLongs Counter
  accPppLinkBadFCSs Counter
  accPppLinkLocalMRU INTEGER
  accPppLinkRemoteMRU INTEGER
  accPppLinkLocalToPeerACCMap OCTET STRING
  accPppLinkPeerToLocalACCMap OCTET STRING
  accPppLinkLocalToRemotePC INTEGER
  accPppLinkRemoteToLocalPC INTEGER
  accPppLinkLocalToRemoteAC INTEGER
  accPppLinkRemoteToLocalAC INTEGER
  accPppLinkTransmit32BitFcs INTEGER
  accPppLinkReceive32BitFcs INTEGER
  accPppLinkOperStatus INTEGER
  accPppLinkPacketTooShorts Counter
  accPppLinkUnknownProtocols Counter
  accPppLinkPacketInDiscards Counter
  accPppLinkPacketOutDiscards Counter

AccPppLcpConfigEntry  
SEQUENCE    
  accPppLcpConfigIndex INTEGER
  accPppLcpConfigInitialMRU INTEGER
  accPppLcpConfigReceiveACCMap OCTET STRING
  accPppLinkConfigXmitACCMap OCTET STRING
  accPppLcpConfigMagicNumber INTEGER
  accPppLcpConfig32BitFCS INTEGER
  accPppLcpRestartTimer INTEGER
  accPppLcpMaxTerminate INTEGER
  accPppLcpMaxConfigure INTEGER
  accPppLcpMaxFailure INTEGER
  accPppLcpMonInterval INTEGER
  accPppLcpMonEvents INTEGER
  accPppLcpMonThreshold INTEGER
  accPppLcpAdminStatus INTEGER
  accPppLinkMsgLevel INTEGER

AccPppLqrEntry  
SEQUENCE    
  accPppLqrIndex INTEGER
  accPppLqrQuality INTEGER
  accPppLqrInGoodOctets Counter
  accPppLqrLocalPeriod INTEGER
  accPppLqrRemotePeriod INTEGER
  accPppLqrOutLQRs Counter
  accPppLqrInLQRs Counter

AccPppLqrConfigEntry  
SEQUENCE    
  accPppLqrConfigIndex INTEGER
  accPppLqrConfigPeriod INTEGER
  accPppLqrConfigStatus INTEGER

AccPppIpcpEntry  
SEQUENCE    
  accPppIpcpIndex INTEGER
  accPppIpcpLocalToRemoteCompressionProtocol INTEGER
  accPppIpcpRemoteToLocalCompressionProtocol INTEGER
  accPppIpcpRemoteMaxSlotId INTEGER
  accPppIpcpLocalMaxSlotId INTEGER
  accPppIpOperStatus INTEGER

AccPppIpcpConfigEntry  
SEQUENCE    
  accPppIpcpConfigIndex INTEGER
  accPppIpcpConfigCompression INTEGER
  accPppIpcpConfigStatus INTEGER

AccPppBncpEntry  
SEQUENCE    
  accPppBncpIndex INTEGER
  accPppBncpLocalToRemoteTinygramCompression INTEGER
  accPppBncpRemoteToLocalTinygramCompression INTEGER
  accPppBncpLocalToRemoteLanId INTEGER
  accPppBncpRemoteToLocalLanId INTEGER
  accPppBncpOperStatus INTEGER

AccPppBncpConfigEntry  
SEQUENCE    
  accPppBncpConfigIndex INTEGER
  accPppBncpConfigTinygram INTEGER
  accPppBncpConfigRingId INTEGER
  accPppBncpConfigLineId INTEGER
  accPppBncpConfigLanId INTEGER
  accPppBncpConfigAdminStatus INTEGER

AccPppXnsEntry  
SEQUENCE    
  accPppXnsIndex INTEGER
  accPppXnsOperStatus INTEGER

AccPppXnsConfigEntry  
SEQUENCE    
  accPppXnsConfigIndex INTEGER
  accPppXnsConfigAdminStatus INTEGER

AccPppIpxEntry  
SEQUENCE    
  accPppIpxIndex INTEGER
  accPppIpxOperStatus INTEGER

AccPppIpxConfigEntry  
SEQUENCE    
  accPppIpxConfigIndex INTEGER
  accPppIpxConfigAdminStatus INTEGER

AccPppAppleEntry  
SEQUENCE    
  accPppAppleIndex INTEGER
  accPppAppleOperStatus INTEGER

AccPppAppleConfigEntry  
SEQUENCE    
  accPppAppleConfigIndex INTEGER
  accPppAppleConfigAdminStatus INTEGER

AccPppDecEntry  
SEQUENCE    
  accPppDecIndex INTEGER
  accPppDecOperStatus INTEGER

AccPppDecConfigEntry  
SEQUENCE    
  accPppDecConfigIndex INTEGER
  accPppDecConfigAdminStatus INTEGER

AccPppProtocolEntry  
SEQUENCE    
  accPppProtocolIndex INTEGER
  accPppProtocolProtocol INTEGER
  accPppProtocolAdminStatus INTEGER
  accPppProtocolOperStatus INTEGER

AccPppAuthStatEntry  
SEQUENCE    
  accPppAuthStatIndex INTEGER
  accPppAuthStatPapReqSents Counter
  accPppAuthStatPapReqRcvs Counter
  accPppAuthStatPapAckSents Counter
  accPppAuthStatPapAckRcvs Counter
  accPppAuthStatPapNakSents Counter
  accPppAuthStatPapNakRcvs Counter
  accPppAuthStatPapRetryTimeouts Counter
  accPppAuthStatChapChallengeSents Counter
  accPppAuthStatChapChallengeRcvs Counter
  accPppAuthStatChapResponseSents Counter
  accPppAuthStatChapResponseRcvs Counter
  accPppAuthStatChapAckSents Counter
  accPppAuthStatChapAckRcvs Counter
  accPppAuthStatChapNakSents Counter
  accPppAuthStatChapNakRcvs Counter
  accPppAuthStatChapResponseTimeouts Counter
  accPppAuthStatChapChallengeTimeouts Counter
  accPppAuthStatChapAckNakTimeouts Counter
  accPppAuthStatLastNegoOptions INTEGER
  accPppAuthStatOutgoingCallMisMatchs Counter

AccPppAuthParmEntry  
SEQUENCE    
  accPppAuthParmIndex INTEGER
  accPppAuthParmUserNameIn DisplayString
  accPppAuthParmPasswordIn DisplayString
  accPppAuthParmMethodIn INTEGER
  accPppAuthParmUserNameOut DisplayString
  accPppAuthParmPasswordOut DisplayString
  accPppAuthParmMethodOut INTEGER
  accPppAuthParmRetryInterval TimeTicks
  accPppAuthParmRetryCount INTEGER
  accPppAuthParmAcctOption INTEGER

AccIpHeaderCompStatEntry  
SEQUENCE    
  accPppLinkVjhcStatIndex INTEGER
  accPppLinkVjhcOper INTEGER
  accPppLinkVjhcNegot INTEGER
  accPppLinkVjhcCompIn INTEGER
  accPppLinkVjhcUnCompIn INTEGER
  accPppLinkVjhcErrIn INTEGER
  accPppLinkVjhcCompOut INTEGER
  accPppLinkVjhcUnCompOut INTEGER
  accPppLinkVjhcErrOut INTEGER

CallAddress  
OCTET STRING    

BackupPort  
INTEGER    

PhysicalPort  
INTEGER    

AccDialBackupEntry  
SEQUENCE    
  accDialBackupPort BackupPort
  accDialBackupPrimary PhysicalPort
  accDialBackupControl INTEGER
  accDialBackupRetry INTEGER
  accDialBackupDamp INTEGER
  accDialBackupCallCongestion INTEGER
  accDialBackupClearCongestion INTEGER
  accDialBackupCallError INTEGER
  accDialBackupCallAddress CallAddress
  accDialBackupStatus INTEGER
  accDialBackupState INTEGER

AccDialPortEntry  
SEQUENCE    
  accDialPortIndex INTEGER
  accDialPortContents INTEGER
  accDialPortStationType INTEGER
  accDialPortAdminState INTEGER
  accDialPortCallState INTEGER
  accDialPortRetryInterval TimeTicks
  accDialPortRetryCount INTEGER
  accDialPortClearingInterv TimeTicks
  accDialPortMessageLevel INTEGER
  accDialPortPhysicalPort INTEGER
  accDialPortCallAddress OCTET STRING
  accDialPortPhysicalPortStr OCTET STRING
  accDialPortCallAddressStr OCTET STRING
  accDialPortPassword OCTET STRING
  accDialPortName OCTET STRING
  accDialPortAuthType INTEGER
  accDialPortSessionTimeout INTEGER
  accDialPortPriority INTEGER
  accDialPortCallBack INTEGER
  accDialPortProtocol INTEGER
  accDialPortAuthPeer INTEGER
  accDialPortPromptState INTEGER
  accDialPortLogin OCTET STRING

AccDialPortStatEntry  
SEQUENCE    
  accDialPortStatIndex INTEGER
  accDialPortStatActPhysPort OCTET STRING
  accDialPortStatState INTEGER
  accDialPortStatTrigFwdr OCTET STRING
  accDialPortStatElapsedTime TimeTicks
  accDialPortStatTrigSrcAddr OCTET STRING
  accDialPortStatTrigCallAddr OCTET STRING
  accDialPortStatSuccessOuts Counter
  accDialPortStatUnsuccessOuts Counter
  accDialPortStatSuccessIns Counter
  accDialPortStatUnsuccessIns Counter
  accDialPortStatAuthTypeClashes Counter
  accDialPortStatDisconnReasons INTEGER

AccDialOrigAtEntry  
SEQUENCE    
  accDialOrigAtStatus INTEGER
  accDialOrigAtDestStart OCTET STRING
  accDialOrigAtDestEnd OCTET STRING
  accDialOrigAtSourceStart OCTET STRING
  accDialOrigAtSourceEnd OCTET STRING
  accDialOrigAtTraffic INTEGER
  accDialOrigAtAction INTEGER

AccDialOrigDnEntry  
SEQUENCE    
  accDialOrigDnStatus INTEGER
  accDialOrigDnDestAddr INTEGER
  accDialOrigDnSourceAddr INTEGER
  accDialOrigDnAction INTEGER

AccDialOrigBrEntry  
SEQUENCE    
  accDialOrigBrStatus INTEGER
  accDialOrigBrDestMacAddr OCTET STRING
  accDialOrigBrSourceMacAddr OCTET STRING
  accDialOrigBrAction INTEGER

AccDialOrigIdpEntry  
SEQUENCE    
  accDialOrigIdpStatus INTEGER
  accDialOrigIdpDestNet OCTET STRING
  accDialOrigIdpSourceNet OCTET STRING
  accDialOrigIdpAction INTEGER

AccDialOrigIpEntry  
SEQUENCE    
  accDialOrigIpStatus INTEGER
  accDialOrigIpDestAddr IpAddress
  accDialOrigIpDestMask IpAddress
  accDialOrigIpSourceAddr IpAddress
  accDialOrigIpSourceMask IpAddress
  accDialOrigIpParm OCTET STRING
  accDialOrigIpAction INTEGER

AccDialOrigIpxEntry  
SEQUENCE    
  accDialOrigIpxStatus INTEGER
  accDialOrigIpxDestNet OCTET STRING
  accDialOrigIpxSourceNet OCTET STRING
  accDialOrigIpxAction INTEGER

AccDialOrigSrEntry  
SEQUENCE    
  accDialOrigSrStatus INTEGER
  accDialOrigSrDestMacAddr OCTET STRING
  accDialOrigSrSourceMacAddr OCTET STRING
  accDialOrigSrAction INTEGER

AccDialPortConnEntry  
SEQUENCE    
  accDialPortConnIndex INTEGER
  accDialPortConnUser OCTET STRING
  accDialPortConnPhyPort INTEGER
  accDialPortConnLogPort INTEGER
  accDialPortConnDir INTEGER
  accDialPortConnAuth IpAddress
  accDialPortConnStart TimeTicks
  accDialPortConnProf OCTET STRING
  accDialPortConnStack OCTET STRING
  accDialPortConnAddr IpAddress
  accDialPortConnState INTEGER

AccPppCompressEntry  
SEQUENCE    
  accPppCompressIndex INTEGER
  accPppCompressMsgLevel INTEGER
  accPppCompressMethod INTEGER
  accPppCompressStream INTEGER
  accPppCompressNegoMethodIn INTEGER
  accPppCompressNegoMethodOut INTEGER
  accPppCompressNegoStreamIn INTEGER
  accPppCompressNegoStreamOut INTEGER

AccPppCompressStatEntry  
SEQUENCE    
  accPppCompressStatIndex INTEGER
  accPppCompressStatStatusIn INTEGER
  accPppCompressStatStatusOut INTEGER
  accPppCompressStatAvgCompIn Gauge
  accPppCompressStatAvgCompOut Gauge
  accPppCompressStatInOctets Counter
  accPppCompressStatOutOctets Counter
  accPppCompressStatInPackets Counter
  accPppCompressStatOutPackets Counter
  accPppCompressUnCompInStats Counter
  accPppCompressUnCompOutStats Counter
  accPppCompressStatHdrErrors Counter
  accPppCompressStatResyncs Counter
  accPppCompressStatNoEndMarks Counter
  accPppCompressStatNoAvailBufs Counter
  accPppCompressStatRcvResetReqs Counter
  accPppCompressStatRcvResetAcks Counter
  accPppCompressStatSndResetReqs Counter
  accPppCompressStatSndResetAcks Counter
  accPppCompressStatExpandIn INTEGER
  accPppCompressStatExpandOut INTEGER
  accPppCompressStatDiscardIn INTEGER
  accPppCompressStatDiscardOut INTEGER

AccDialPortCompressEntry  
SEQUENCE    
  accDialPortCompressIndex INTEGER
  accDialPortCompressMsgLevel INTEGER
  accDialPortCompressMethod INTEGER
  accDialPortCompressStream INTEGER
  accDialPortCompressNegoMethodIn INTEGER
  accDialPortCompressNegoMethodOut INTEGER
  accDialPortCompressNegoStreamIn INTEGER
  accDialPortCompressNegoStreamOut INTEGER

AccMlPppCompressEntry  
SEQUENCE    
  accMlPppCompressIndex INTEGER
  accMlPppCompressMsgLevel INTEGER
  accMlPppCompressMethod INTEGER
  accMlPppCompressStream INTEGER
  accMlPppCompressNegoMethodIn INTEGER
  accMlPppCompressNegoMethodOut INTEGER
  accMlPppCompressNegoStreamIn INTEGER
  accMlPppCompressNegoStreamOut INTEGER

AccMlPppCompressStatEntry  
SEQUENCE    
  accMlPppCompressStatIndex INTEGER
  accMlPppCompressStatStatus INTEGER
  accMlPppCompressStatInOctets Counter
  accMlPppCompressStatOutOctets Counter
  accMlPppCompressStatInPackets Counter
  accMlPppCompressStatOutPackets Counter
  accMlPppCompressUnCompInStats Counter
  accMlPppCompressUnCompOutStats Counter
  accMlPppCompressStatAvgCompIn Gauge
  accMlPppCompressStatAvgCompOut Gauge
  accMlPppCompressStatHdrErrors Counter
  accMlPppCompressStatResyncs Counter
  accMlPppCompressStatNoEndMarks Counter
  accMlPppCompressStatNoAvailBufs Counter
  accMlPppCompressStatRcvResetReqs Counter
  accMlPppCompressStatRcvResetAcks Counter
  accMlPppCompressStatSndResetReqs Counter
  accMlPppCompressStatSndResetAcks Counter

Defined Values

accPpp 1.1.1.32
OBJECT IDENTIFIER    

accPppLinkTable 1.1.1.32.1
A table containing PPP-link specific variables for this PPP implementation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppLinkEntry

accPppLinkEntry 1.1.1.32.1.1
Management information about a particular PPP Link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppLinkEntry  

accPppLinkIndex 1.1.1.32.1.1.1
Interface number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkPhysicalIndex 1.1.1.32.1.1.2
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkBadAddresses 1.1.1.32.1.1.3
The number of packets received with an incorrect Address Field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLinkBadControls 1.1.1.32.1.1.4
The number of packets received on this link with an incorrect Control Field.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLinkPacketTooLongs 1.1.1.32.1.1.5
The number of received packets that have been discarded because their length exceeded the MRU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLinkBadFCSs 1.1.1.32.1.1.6
The number of bad HDLC frames received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLinkLocalMRU 1.1.1.32.1.1.7
The final negotiated MRU value for the local PPP Entity. This value is the MRU that the remote entity has accepted for the local PPP entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkRemoteMRU 1.1.1.32.1.1.8
The final negotiated MRU value for the remote PPP Entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkLocalToPeerACCMap 1.1.1.32.1.1.9
For future applications. Unused in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accPppLinkPeerToLocalACCMap 1.1.1.32.1.1.10
For future applications. Unused in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accPppLinkLocalToRemotePC 1.1.1.32.1.1.11
For future applications. Unused in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkRemoteToLocalPC 1.1.1.32.1.1.12
For future applications. Unused in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkLocalToRemoteAC 1.1.1.32.1.1.13
For future applications. Unused in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkRemoteToLocalAC 1.1.1.32.1.1.14
For future applications. Unused in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkTransmit32BitFcs 1.1.1.32.1.1.15
For future applications. Unused in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkReceive32BitFcs 1.1.1.32.1.1.16
For future applications. Unused in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkOperStatus 1.1.1.32.1.1.17
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initial(1), starting(2), closed(3), stopped(4), closing(5), stopping(6), req-sent(7), ack-rcvd(8), ack-sent(9), opened(10)  

accPppLinkPacketTooShorts 1.1.1.32.1.1.18
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLinkUnknownProtocols 1.1.1.32.1.1.19
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLinkPacketInDiscards 1.1.1.32.1.1.20
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLinkPacketOutDiscards 1.1.1.32.1.1.21
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLcpConfigTable 1.1.1.32.2
A table containing the LCP configuration parameters for this PPP Link. These variables represent the initial configuration of the PPP Link. The actual values of the parameters may be changed when the link is brought up via the LCP options negotiation mechanism.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppLcpConfigEntry

accPppLcpConfigEntry 1.1.1.32.2.1
Configuration information about a particular PPP Link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppLcpConfigEntry  

accPppLcpConfigIndex 1.1.1.32.2.1.1
Interface number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLcpConfigInitialMRU 1.1.1.32.2.1.2
The initial Maximum Receive Unit (MRU) that the local PPP entity will advertise to the remote entity. If the value of this variable is 0 then the local PPP entity will not advertise any MRU to the remote entity and the default MRU will be assumed. Changing this object will have effect when the link is next restarted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLcpConfigReceiveACCMap 1.1.1.32.2.1.3
For future applications. Unused in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accPppLinkConfigXmitACCMap 1.1.1.32.2.1.4
For future applications. Unused in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accPppLcpConfigMagicNumber 1.1.1.32.2.1.5
If true(2) then the local node will attempt to perform Magic Number negotiation with the remote node. If false(1) then this negotiation is not performed. In any event, the local node will comply with any magic number negotiations attempted by the remote node, per the PPP specification. Changing this object will have effect when the link is next restarted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(1), true(2)  

accPppLcpConfig32BitFCS 1.1.1.32.2.1.6
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLcpRestartTimer 1.1.1.32.2.1.7
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..3600  

accPppLcpMaxTerminate 1.1.1.32.2.1.8
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

accPppLcpMaxConfigure 1.1.1.32.2.1.9
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

accPppLcpMaxFailure 1.1.1.32.2.1.10
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

accPppLcpMonInterval 1.1.1.32.2.1.11
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..3600  

accPppLcpMonEvents 1.1.1.32.2.1.12
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

accPppLcpMonThreshold 1.1.1.32.2.1.13
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

accPppLcpAdminStatus 1.1.1.32.2.1.14
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

accPppLinkMsgLevel 1.1.1.32.2.1.15
PPP trap message level which may be set on a per port basis. No traps with a severity level greater the value set will be generated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..7  

accPppLqrTable 1.1.1.32.3
Table containing the LQR parameters and statistics for the local PPP entity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppLqrEntry

accPppLqrEntry 1.1.1.32.3.1
LQR information for a particular PPP link. A PPP link will have an entry in this table if and only if LQR Quality Monitoring has been successfully negotiated for said link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppLqrEntry  

accPppLqrIndex 1.1.1.32.3.1.1
Interface number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLqrQuality 1.1.1.32.3.1.2
The current quality of the link as declared by the local PPP entity's Link-Quality Management modules. No effort is made to define good or bad, nor the policy used to determine it.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER good(1), bad(2)  

accPppLqrInGoodOctets 1.1.1.32.3.1.3
The LQR InGoodOctets counter for this link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLqrLocalPeriod 1.1.1.32.3.1.4
The LQR reporting period that is in effect for the local PPP entity. The local entity received a configure-ack for this value from the remote PPP entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLqrRemotePeriod 1.1.1.32.3.1.5
The LQR reporting period that is in effect for the remote PPP entity. The local entity sent a configure-ack for this value in response to the configure-req from the remote PPP entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLqrOutLQRs 1.1.1.32.3.1.6
The value of the OutLQRs counter on the local node for the link identified by accPppLqrLinkIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLqrInLQRs 1.1.1.32.3.1.7
The value of the InLQRs counter on the local node for the link identified by accPppLqrLinkIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppLqrConfigTable 1.1.1.32.4
Table containing the LQR Configuration parameters for the local PPP entity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppLqrConfigEntry

accPppLqrConfigEntry 1.1.1.32.4.1
LQR configuration information for a particular PPP link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppLqrConfigEntry  

accPppLqrConfigIndex 1.1.1.32.4.1.1
Interface number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLqrConfigPeriod 1.1.1.32.4.1.2
The LQR Reporting Period that the local PPP entity will attempt to negotiate with the remote entity, in units of seconds. Changing this object will have effect when the link is next restarted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483648  

accPppLqrConfigStatus 1.1.1.32.4.1.3
If enabled(2) then the local node will attempt to perform LQR negotiation with the remote node. If disabled(1) then this negotiation is not performed. In any event, the local node will comply with any magic number negotiations attempted by the remote node, per the PPP specification. Changing this object will have effect when the link is next restarted. Setting this object to the value disabled(1) has the effect of invalidating the corresponding entry in the accPppLqrConfigTable object. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

accPppIpcpTable 1.1.1.32.5
Table containing the IPCP parameters and statistics for the local PPP entity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppIpcpEntry

accPppIpcpEntry 1.1.1.32.5.1
IPCP information for a particular PPP link. A PPP link will have an entry in this table if and only if running IP over the PPP link has been successfully negotiated for said link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppIpcpEntry  

accPppIpcpIndex 1.1.1.32.5.1.1
Interface number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppIpcpLocalToRemoteCompressionProtocol 1.1.1.32.5.1.2
The IP compression protocol that the local PPP-IP entity uses when sending packets to the remote PPP-IP entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), vj-tcp(2)  

accPppIpcpRemoteToLocalCompressionProtocol 1.1.1.32.5.1.3
The IP compression protocol that the remote PPP-IP entity uses when sending packets to the local PPP-IP entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), vj-tcp(2)  

accPppIpcpRemoteMaxSlotId 1.1.1.32.5.1.4
The Max-Slot-Id parameter that the remote node has advertised and that is in use on the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

accPppIpcpLocalMaxSlotId 1.1.1.32.5.1.5
The Max-Slot-Id parameter that the local node has advertised and that is in use on the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

accPppIpOperStatus 1.1.1.32.5.1.6
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initial(1), starting(2), closed(3), stopped(4), closing(5), stopping(6), req-sent(7), ack-rcvd(8), ack-sent(9), opened(10)  

accPppIpcpConfigTable 1.1.1.32.6
Table containing the IPCP parameters and statistics for the local PPP entity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppIpcpConfigEntry

accPppIpcpConfigEntry 1.1.1.32.6.1
IPCP information for a particular PPP link. A PPP link will have an entry in this table if and only if running IP over the PPP link has been successfully negotiated for said link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppIpcpConfigEntry  

accPppIpcpConfigIndex 1.1.1.32.6.1.1
The value of ifIndex that identifies the entry in the ifTable that is associated with the local IPCP entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppIpcpConfigCompression 1.1.1.32.6.1.2
If none(1) then the local node will not attempt to negotiate any IP Compression option. Otherwise, the local node will attempt to negotiate compression mode indicated by the enumerated value Changing this object will have effect when the link is next restarted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), vj-tcp(2)  

accPppIpcpConfigStatus 1.1.1.32.6.1.3
If enabled(2) then the local node will allow IP traffic to flow across the link. If disabled(1) then IP traffic will not be allowed to flow across the link. Setting this object to the value disabled(1) has the effect of invalidating the corresponding entry in the accPppIpcpConfigTable object. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

accPppBncpTable 1.1.1.32.7
Table containing the parameters and statistics for the local PPP entity that are related to the operation of Bridging over the PPP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppBncpEntry

accPppBncpEntry 1.1.1.32.7.1
Bridging NCP information for a particular PPP link. A PPP link will have an entry in this table if and only if Bridging over PPP has been successfully negotiated for said link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppBncpEntry  

accPppBncpIndex 1.1.1.32.7.1.1
Interface number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppBncpLocalToRemoteTinygramCompression 1.1.1.32.7.1.2
Indicates whether the local node will perform Tinygram Compression when sending packets to the remote entity. If false then the local entity will not perform Tinygram Compression. If true then the local entity will perform Tinygram Compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(1), true(2)  

accPppBncpRemoteToLocalTinygramCompression 1.1.1.32.7.1.3
Indicates what the local node believes to be the remote node will perform Tinygram Compression when sending packets to the local node. If false then the remote entity is not expected to perform Tinygram Compression. If true then the remote entity is expected to perform Tinygram Compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(1), true(2)  

accPppBncpLocalToRemoteLanId 1.1.1.32.7.1.4
Indicates whether the local node will include the LAN Identification field in transmitted packets or not. If false(1) then the local node will not transmit this field, true(2) means that the field will be transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(1), true(2)  

accPppBncpRemoteToLocalLanId 1.1.1.32.7.1.5
Indicates whether the remote node has indicated that it will include the LAN Identification field in transmitted packets or not. If false(1) then the field will not be transmitted, if true(2) then the field will be transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER false(1), true(2)  

accPppBncpOperStatus 1.1.1.32.7.1.6
Operational status of the PPP link for this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initial(1), starting(2), closed(3), stopped(4), closing(5), stopping(6), req-sent(7), ack-rcvd(8), ack-sent(9), opened(10)  

accPppBncpConfigTable 1.1.1.32.8
Table containing the parameters and statistics for the local PPP entity that are related to the operation of Bridging over the PPP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppBncpConfigEntry

accPppBncpConfigEntry 1.1.1.32.8.1
Bridging NCP information for a particular PPP link. A PPP link will have an entry in this table if and only if Bridging over PPP has been successfully negotiated for said link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppBncpConfigEntry  

accPppBncpConfigIndex 1.1.1.32.8.1.1
The value of ifIndex that identifies the entry in the interface table that is associated with the local PPP Bridging NCP entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppBncpConfigTinygram 1.1.1.32.8.1.2
If false then the local BNCP entity will not initiate the Tinygram Compression Option Negotiation. If true then the local BNCP entity will initiate negotiation of this option.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER false(1), true(2)  

accPppBncpConfigRingId 1.1.1.32.8.1.3
If false then the local PPP Entity will not initiate a Remote Ring Identification Option negotiation. If true then the local PPP entity will intiate this negotiation. This MIB object is relevant only if the interface is for 802.5 Token Ring bridging.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER false(1), true(2)  

accPppBncpConfigLineId 1.1.1.32.8.1.4
If false then the local PPP Entity is not to initiate a Line Identification Option negotiation. If true then the local PPP entity will intiate this negotiation. This MIB object is relevant only if the interface is for 802.5 Token Ring bridging.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER false(1), true(2)  

accPppBncpConfigLanId 1.1.1.32.8.1.5
If false then the local BNCP entity will not initiate the LAN Identification Option Negotiation. If true then the local BNCP entity will initiate negotiation of this option.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER false(1), true(2)  

accPppBncpConfigAdminStatus 1.1.1.32.8.1.6
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

accPppXnsTable 1.1.1.32.9
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppXnsEntry

accPppXnsEntry 1.1.1.32.9.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppXnsEntry  

accPppXnsIndex 1.1.1.32.9.1.1
Same as ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppXnsOperStatus 1.1.1.32.9.1.2
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initial(1), starting(2), closed(3), stopped(4), closing(5), stopping(6), req-sent(7), ack-rcvd(8), ack-sent(9), opened(10)  

accPppXnsConfigTable 1.1.1.32.10
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppXnsConfigEntry

accPppXnsConfigEntry 1.1.1.32.10.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppXnsConfigEntry  

accPppXnsConfigIndex 1.1.1.32.10.1.1
Same as ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppXnsConfigAdminStatus 1.1.1.32.10.1.3
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

accPppIpxTable 1.1.1.32.11
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppIpxEntry

accPppIpxEntry 1.1.1.32.11.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppIpxEntry  

accPppIpxIndex 1.1.1.32.11.1.1
Same as ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppIpxOperStatus 1.1.1.32.11.1.2
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initial(1), starting(2), closed(3), stopped(4), closing(5), stopping(6), req-sent(7), ack-rcvd(8), ack-sent(9), opened(10)  

accPppIpxConfigTable 1.1.1.32.12
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppIpxConfigEntry

accPppIpxConfigEntry 1.1.1.32.12.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppIpxConfigEntry  

accPppIpxConfigIndex 1.1.1.32.12.1.1
Same as ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppIpxConfigAdminStatus 1.1.1.32.12.1.3
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

accPppAppleTable 1.1.1.32.13
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppAppleEntry

accPppAppleEntry 1.1.1.32.13.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppAppleEntry  

accPppAppleIndex 1.1.1.32.13.1.1
Same as ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppAppleOperStatus 1.1.1.32.13.1.2
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initial(1), starting(2), closed(3), stopped(4), closing(5), stopping(6), req-sent(7), ack-rcvd(8), ack-sent(9), opened(10)  

accPppAppleConfigTable 1.1.1.32.14
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppAppleConfigEntry

accPppAppleConfigEntry 1.1.1.32.14.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppAppleConfigEntry  

accPppAppleConfigIndex 1.1.1.32.14.1.1
Same as ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppAppleConfigAdminStatus 1.1.1.32.14.1.3
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

accPppDecTable 1.1.1.32.15
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppDecEntry

accPppDecEntry 1.1.1.32.15.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppDecEntry  

accPppDecIndex 1.1.1.32.15.1.1
Same as ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppDecOperStatus 1.1.1.32.15.1.2
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initial(1), starting(2), closed(3), stopped(4), closing(5), stopping(6), req-sent(7), ack-rcvd(8), ack-sent(9), opened(10)  

accPppDecConfigTable 1.1.1.32.16
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppDecConfigEntry

accPppDecConfigEntry 1.1.1.32.16.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppDecConfigEntry  

accPppDecConfigIndex 1.1.1.32.16.1.1
Same as ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppDecConfigAdminStatus 1.1.1.32.16.1.3
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

accPppProtocolTable 1.1.1.32.17
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppProtocolEntry

accPppProtocolEntry 1.1.1.32.17.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppProtocolEntry  

accPppProtocolIndex 1.1.1.32.17.1.1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppProtocolProtocol 1.1.1.32.17.1.2
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip(33), osi(35), idp(37), decnet(39), appletalk(41), ipx(43), bridge(49), vines(53), multilink(61), illcp(251), ccp(253)  

accPppProtocolAdminStatus 1.1.1.32.17.1.3
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

accPppProtocolOperStatus 1.1.1.32.17.1.4
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initial(1), starting(2), closed(3), stopped(4), closing(5), stopping(6), req-sent(7), ack-rcvd(8), ack-sent(9), opened(10)  

accPppMsg 1.1.1.32.18
OBJECT IDENTIFIER    

accPppMsgLevel 1.1.1.32.18.1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..7  

accPppAuthStatTable 1.1.1.32.19
A table containing PPP authentication specific variables for this PPP implementation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppAuthStatEntry

accPppAuthStatEntry 1.1.1.32.19.1
Management information about a authentication of a particular PPP Link.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppAuthStatEntry  

accPppAuthStatIndex 1.1.1.32.19.1.1
Interface number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppAuthStatPapReqSents 1.1.1.32.19.1.2
The number of times a PAP request sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatPapReqRcvs 1.1.1.32.19.1.3
The number of times a PAP request received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatPapAckSents 1.1.1.32.19.1.4
The number of times a PAP Ack sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatPapAckRcvs 1.1.1.32.19.1.5
The number of times a PAP Ack Received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatPapNakSents 1.1.1.32.19.1.6
The number of times a PAP Nak sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatPapNakRcvs 1.1.1.32.19.1.7
The number of times a PAP Nak received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatPapRetryTimeouts 1.1.1.32.19.1.8
The number of times a PAP retry timeout.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapChallengeSents 1.1.1.32.19.1.9
The number of times a Challenge sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapChallengeRcvs 1.1.1.32.19.1.10
The number of times a challenge received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapResponseSents 1.1.1.32.19.1.11
The number of times a CHAP response sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapResponseRcvs 1.1.1.32.19.1.12
The number of times a CHAP response received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapAckSents 1.1.1.32.19.1.13
The number of times a CHAP ACK sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapAckRcvs 1.1.1.32.19.1.14
The number of times a CHAP ACK received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapNakSents 1.1.1.32.19.1.15
The number of times a CHAP NAK sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapNakRcvs 1.1.1.32.19.1.16
The number of times a CHAP NAK received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapResponseTimeouts 1.1.1.32.19.1.17
The number of times a waiting CHAP response timeout.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapChallengeTimeouts 1.1.1.32.19.1.18
The number of times a waiting CHAP challenge timeout.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatChapAckNakTimeouts 1.1.1.32.19.1.19
The number of times a waiting CHAP ACK/NAK timeout.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthStatLastNegoOptions 1.1.1.32.19.1.20
The most recent authentication method is negotiated
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppAuthStatOutgoingCallMisMatchs 1.1.1.32.19.1.21
The number of times an outgoing call dial port authentication method is differnet than PAP authentication negotiated in PPP
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppAuthParmTable 1.1.1.32.20
PPP Authentication Parameter Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppAuthParmEntry

accPppAuthParmEntry 1.1.1.32.20.1
PPP Authentication Parameter Table Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppAuthParmEntry  

accPppAuthParmIndex 1.1.1.32.20.1.1
The ifIndex of the PPP physical port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppAuthParmUserNameIn 1.1.1.32.20.1.2
incoming (remote) user name
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

accPppAuthParmPasswordIn 1.1.1.32.20.1.3
incoming (remote) password or secret
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

accPppAuthParmMethodIn 1.1.1.32.20.1.4
incoming authentication method
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), pap(2), chap(3), chap-or-pap(4)  

accPppAuthParmUserNameOut 1.1.1.32.20.1.5
outgoing (local) user name
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

accPppAuthParmPasswordOut 1.1.1.32.20.1.6
outgoing (local) password or secret
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

accPppAuthParmMethodOut 1.1.1.32.20.1.7
outgoing authentication method
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), pap(2), chap(3), chap-or-pap(4)  

accPppAuthParmRetryInterval 1.1.1.32.20.1.8
authentication retry interval
Status: mandatory Access: read-write
OBJECT-TYPE    
  TimeTicks  

accPppAuthParmRetryCount 1.1.1.32.20.1.9
authentication retry count
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

accPppAuthParmAcctOption 1.1.1.32.20.1.10
accounting administrative status (if on, account is performed for this link
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

accIpHeaderCompStatTable 1.1.1.32.23
IP Header Compression Statistics Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccIpHeaderCompStatEntry

accIpHeaderCompStatEntry 1.1.1.32.23.1
IP Header Compression Statistics Entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccIpHeaderCompStatEntry  

accPppLinkVjhcStatIndex 1.1.1.32.23.1.1
The ifIndex of the PPP physical port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkVjhcOper 1.1.1.32.23.1.2
The VJ header Comp State of the PPP physical port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

accPppLinkVjhcNegot 1.1.1.32.23.1.3
The VJ header Comp Negotiation Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApp(1), failed(2), success(3)  

accPppLinkVjhcCompIn 1.1.1.32.23.1.4
The VJ header Compresses packets received
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkVjhcUnCompIn 1.1.1.32.23.1.5
The VJ header UnCompressed packets received
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkVjhcErrIn 1.1.1.32.23.1.6
The VJ header Error packets received
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkVjhcCompOut 1.1.1.32.23.1.7
The VJ header Compresses packets Sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkVjhcUnCompOut 1.1.1.32.23.1.8
The VJ header UnCompressed packets Sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppLinkVjhcErrOut 1.1.1.32.23.1.9
The VJ header Error packets Sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppTraps 1.1.1.32.24
OBJECT IDENTIFIER    

accPppTrapMsg 1.1.1.32.24.1
PPP Trap Message
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

accDial 1.1.1.31
OBJECT IDENTIFIER    

accDialBackupTable 1.1.1.31.1
A list of associations between physical ports.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialBackupEntry

accDialBackupEntry 1.1.1.31.1.1
An association between two ports.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialBackupEntry  

accDialBackupPort 1.1.1.31.1.1.1
The ifIndex value of the port backing up the primary port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  BackupPort  

accDialBackupPrimary 1.1.1.31.1.1.2
The ifIndex value of the port backed up.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysicalPort  

accDialBackupControl 1.1.1.31.1.1.3
Backup Control indicates under what conditions a call is placed or accepted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER master(1), slave(2), demand(3)  

accDialBackupRetry 1.1.1.31.1.1.4
The number of seconds the system will wait be- fore retrying a failed call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..3600  

accDialBackupDamp 1.1.1.31.1.1.5
Damping factor.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

accDialBackupCallCongestion 1.1.1.31.1.1.6
If the average octet rate transmitted (or, on a master, received) exceeds this percentage times the ifSpeed of the primary link, a call will be placed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..101  

accDialBackupClearCongestion 1.1.1.31.1.1.7
If the sum of the primary and backup link's average octet rates (transmitted or, on a mas- ter, received) falls below this percentage times the ifSpeed of the primary link, an out- standing call will be cleared. If ClearCongestion >= CallCongestion, the entry will not be acted upon by software, but will result in a trap at system startup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..101  

accDialBackupCallError 1.1.1.31.1.1.8
If the average sum of ifInDiscards, ifInEr- rors, ifOutDiscards, ifOutErrors, accLapbStat- BadFCSIns, accLapbStatT1Timeouts, accLapbSta- tREJIns, and accLapbStatREJOuts exceeds this value, a call will be placed. The call will be cleared when the average be- comes zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

accDialBackupCallAddress 1.1.1.31.1.1.9
The address to be called, in ASCII. No validation is performed on this variable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  CallAddress  

accDialBackupStatus 1.1.1.31.1.1.10
If this object is set to 'invalid', the entry is deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

accDialBackupState 1.1.1.31.1.1.11
The current call state from the primary link's perspective. The only values acceptable on a SET are 'manual' and 'clear'. If 'manual' is SET, the backup link will place a call immedi- ately or when it next becomes available. If 'clear' is SET when a call is administratively placed, either the call will be cleared, or the call will continue for another reason. If 'clear' is set when no call is administratively placed, there is no effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER congestOut(1), congestIn(2), errors(3), backup(4), manual(5), clear(6)  

accDialPortTable 1.1.1.31.2
A table containing DOD-port specific variables for this DOD implementation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialPortEntry

accDialPortEntry 1.1.1.31.2.1
Management information about a particular DOD Port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialPortEntry  

accDialPortIndex 1.1.1.31.2.1.1
Dial port number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accDialPortContents 1.1.1.31.2.1.2
Setting this object to invalid deletes dial port or call address or physical port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2)  

accDialPortStationType 1.1.1.31.2.1.3
Type of station for this dial port. Master can place calls, slave can accept calls, demand can do both.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER master(1), slave(2), demand(3)  

accDialPortAdminState 1.1.1.31.2.1.4
The administrative state of this dial port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER down(1), up(2)  

accDialPortCallState 1.1.1.31.2.1.5
The dial state of this dial port. This is more of a operator request than a state. Depending on the current state of the dial port the command that sets the value of this object may or may not be acted immediately.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clear(1), call(2)  

accDialPortRetryInterval 1.1.1.31.2.1.6
Number of seconds allowed to elapse between two dial attempts.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TimeTicks  

accDialPortRetryCount 1.1.1.31.2.1.7
Total number of dial attempts.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

accDialPortClearingInterv 1.1.1.31.2.1.8
Number of seconds to wait with no traffic to hangup this dial session.
Status: mandatory Access: read-write
OBJECT-TYPE    
  TimeTicks  

accDialPortMessageLevel 1.1.1.31.2.1.9
Current message level for how much to display for this dial port. 1 - Error messages. 2 - Unused + 1. 3 - Warning messages + 2. 4 - Unused + 3. 5 - Dial activity + 4. 6 - Unused + 5. 7 - Dial port state changes + 6.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

accDialPortPhysicalPort 1.1.1.31.2.1.10
One of the possible physical ports this dial port may associate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

accDialPortCallAddress 1.1.1.31.2.1.11
One of the possible call addresses this dial port may call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialPortPhysicalPortStr 1.1.1.31.2.1.12
The concatenated string of all physical ports associated with this dial port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accDialPortCallAddressStr 1.1.1.31.2.1.13
The concatenated string of all call address/name entries associated with this dial port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accDialPortPassword 1.1.1.31.2.1.14
The password associated with the call address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialPortName 1.1.1.31.2.1.15
The name associated with the call address. The combination of name and password is used for the outbound PAP negotiation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialPortAuthType 1.1.1.31.2.1.16
The authentication type associated with the dial port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER pap(1), chap(2), chappap(3), none(4), token-chap(5)  

accDialPortSessionTimeout 1.1.1.31.2.1.17
The maximum time a dial session may be connected for in seconds. 0 denotes forever.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

accDialPortPriority 1.1.1.31.2.1.18
Tok_String
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

accDialPortCallBack 1.1.1.31.2.1.19
Determines whether call back is enabled or disabled for this dial port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

accDialPortProtocol 1.1.1.31.2.1.20
Dial port protocol determined by user to be either ppp or X25.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ppp(1), x25(2)  

accDialPortAuthPeer 1.1.1.31.2.1.21
Dial port protocol determined by user to be either ppp or X25.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), forced(2)  

accDialPortPromptState 1.1.1.31.2.1.22
Dial port authentication prompt state.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER login(1), reenter(2), newpin(3), nexttoken(4), inprocess(5), idle(6), disabled(7)  

accDialPortLogin 1.1.1.31.2.1.23
Dial port authentication response to entered token.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accDialPortStatTable 1.1.1.31.3
A table containing the operational parameters for this dial port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialPortStatEntry

accDialPortStatEntry 1.1.1.31.3.1
Current status for this dial port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialPortStatEntry  

accDialPortStatIndex 1.1.1.31.3.1.1
Dial port number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accDialPortStatActPhysPort 1.1.1.31.3.1.2
The physical port currently connected with or recently connected with.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accDialPortStatState 1.1.1.31.3.1.3
The current state of this dial port. The following is a list of valid states: down(0), disconnected(1), queued(2), answering(3), dialing(4), connected(5)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

accDialPortStatTrigFwdr 1.1.1.31.3.1.4
Application which started this dial session. The following is a list of applications: none(0), management(1), inbound(2), callback(12) ip(33), idp(37), decnet(39), appletalk(41), ipx(43), bridging(177), sr(179)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accDialPortStatElapsedTime 1.1.1.31.3.1.5
Number of seconds that this dial port has been in the current state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

accDialPortStatTrigSrcAddr 1.1.1.31.3.1.6
Source address of forwarder message that started this dial session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accDialPortStatTrigCallAddr 1.1.1.31.3.1.7
Phone number connected to during this dial session or the last dial session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accDialPortStatSuccessOuts 1.1.1.31.3.1.8
Number of successfull outgoing calls on this dial port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accDialPortStatUnsuccessOuts 1.1.1.31.3.1.9
Number of unsuccessfull call attempts on this dial port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accDialPortStatSuccessIns 1.1.1.31.3.1.10
Number of successfull incoming calls on this dial port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accDialPortStatUnsuccessIns 1.1.1.31.3.1.11
Total number of unsuccessfull incoming calls.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accDialPortStatAuthTypeClashes 1.1.1.31.3.1.12
Total number of Dial Port Authentication Type mis-matches.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accDialPortStatDisconnReasons 1.1.1.31.3.1.13
The reason this dial port is in the Disconnected state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER mgmtreq(1), netfail(2), locfail(3), idletimeout(4), sessiontimeout(5)  

accDialOrigAtTable 1.1.1.31.4
A table containing dial originate database for Appletalk.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialOrigAtEntry

accDialOrigAtEntry 1.1.1.31.4.1
Dial originate information entry for Appletalk.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialOrigAtEntry  

accDialOrigAtStatus 1.1.1.31.4.1.1
Writing 'invalid' deletes the filter table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2)  

accDialOrigAtDestStart 1.1.1.31.4.1.2
Destination range start for this Appletalk entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigAtDestEnd 1.1.1.31.4.1.3
Destination range end for this Appletalk entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigAtSourceStart 1.1.1.31.4.1.4
Source range start for this Appletalk entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigAtSourceEnd 1.1.1.31.4.1.5
Source range end for this Appletalk entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigAtTraffic 1.1.1.31.4.1.6
Traffic info for this Appletalk entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER any(1), nbp(2), atp(3), aep(4), rtmp(5), zip(6), adsp(7), nbpbroadcast(8), nbplookup(9), nbpreply(10), nbpforwardreq(11)  

accDialOrigAtAction 1.1.1.31.4.1.7
Allow-disallow info for this Appletalk entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

accDialOrigDnTable 1.1.1.31.5
A table containing dial originate database for Decnet.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialOrigDnEntry

accDialOrigDnEntry 1.1.1.31.5.1
Dial originate information entry for Decnet.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialOrigDnEntry  

accDialOrigDnStatus 1.1.1.31.5.1.1
Writing 'invalid' deletes the filter table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2)  

accDialOrigDnDestAddr 1.1.1.31.5.1.2
Destination address for this Decnet entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

accDialOrigDnSourceAddr 1.1.1.31.5.1.3
Source address for this Decnet entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

accDialOrigDnAction 1.1.1.31.5.1.4
Allow-disallow info for this Decnet entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

accDialOrigBrTable 1.1.1.31.6
A table containing dial originate database for Bridge.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialOrigBrEntry

accDialOrigBrEntry 1.1.1.31.6.1
Dial originate information entry for Bridge.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialOrigBrEntry  

accDialOrigBrStatus 1.1.1.31.6.1.1
Writing 'invalid' deletes the filter table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2)  

accDialOrigBrDestMacAddr 1.1.1.31.6.1.2
Destination mac address start for this Bridge entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigBrSourceMacAddr 1.1.1.31.6.1.3
Source mac address for this Bridge entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigBrAction 1.1.1.31.6.1.4
Allow-disallow info for this Bridge entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

accDialOrigIdpTable 1.1.1.31.7
A table containing dial originate database for Idp.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialOrigIdpEntry

accDialOrigIdpEntry 1.1.1.31.7.1
Dial originate information entry for Idp.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialOrigIdpEntry  

accDialOrigIdpStatus 1.1.1.31.7.1.1
Writing 'invalid' deletes the filter table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2)  

accDialOrigIdpDestNet 1.1.1.31.7.1.2
Destination network for this Idp entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigIdpSourceNet 1.1.1.31.7.1.3
Source network for this Idp entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigIdpAction 1.1.1.31.7.1.4
Allow-disallow info for this Idp entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

accDialOrigIpTable 1.1.1.31.8
A table containing dial originate database for Ip.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialOrigIpEntry

accDialOrigIpEntry 1.1.1.31.8.1
Dial originate information entry for Ip.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialOrigIpEntry  

accDialOrigIpStatus 1.1.1.31.8.1.1
Writing 'invalid' deletes the filter table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2)  

accDialOrigIpDestAddr 1.1.1.31.8.1.2
Destination address for this Ip entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

accDialOrigIpDestMask 1.1.1.31.8.1.3
Destination mask for this Ip entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

accDialOrigIpSourceAddr 1.1.1.31.8.1.4
Source address for this Ip entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

accDialOrigIpSourceMask 1.1.1.31.8.1.5
Source mask for this Ip entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

accDialOrigIpParm 1.1.1.31.8.1.6
Filter parameters; Byte 0 is Operation 1 [0,1,2] = [None, !,=] Bytes 1,2 is Protocol Byte 3 is Operation 2 [0 = none [1,2,3,4] = both [!, <, >, =] [5,6,7,8] = destination [!, <, >, =] [9,10,11,12] = source [!, <, >, =] Bytes 4,5 is UDP/TCP port number
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigIpAction 1.1.1.31.8.1.7
Allow-disallow info for this Ip entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

accDialOrigIpxTable 1.1.1.31.9
A table containing dial originate database for Ipx.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialOrigIpxEntry

accDialOrigIpxEntry 1.1.1.31.9.1
Dial originate information entry for Ipx.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialOrigIpxEntry  

accDialOrigIpxStatus 1.1.1.31.9.1.1
Writing 'invalid' deletes the filter table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2)  

accDialOrigIpxDestNet 1.1.1.31.9.1.2
Destination network for this Ipx entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigIpxSourceNet 1.1.1.31.9.1.3
Source network for this Ipx entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigIpxAction 1.1.1.31.9.1.4
Allow-disallow info for this Ipx entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

accDialOrigSrTable 1.1.1.31.10
A table containing dial originate database for Sr.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialOrigSrEntry

accDialOrigSrEntry 1.1.1.31.10.1
Dial originate information entry for Sr.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialOrigSrEntry  

accDialOrigSrStatus 1.1.1.31.10.1.1
Writing 'invalid' deletes the filter table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2)  

accDialOrigSrDestMacAddr 1.1.1.31.10.1.2
Destination mac address for this Sr entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigSrSourceMacAddr 1.1.1.31.10.1.3
Source mac address for this Sr entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accDialOrigSrAction 1.1.1.31.10.1.4
Allow-disallow info for this Sr entry in the dial originate database.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

accDialPortRange 1.1.1.31.11
OBJECT IDENTIFIER    

accDialPortMaxCount 1.1.1.31.11.1
The maximum number of dial on demand ports that can be configured
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..999  

accDialPortRangeStart 1.1.1.31.11.2
The ifIndex for the start of the DOD port range
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accDialPortRangeEnd 1.1.1.31.11.3
The ifIndex for the end of the DOD port range
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accDialPortConnTable 1.1.1.31.12
The table of users currently connected using dial ports
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialPortConnEntry

accDialPortConnEntry 1.1.1.31.12.1
A single connected user's information
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialPortConnEntry  

accDialPortConnIndex 1.1.1.31.12.1.1
Simple incrementing integer index for table based alphabetically on connected user names.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accDialPortConnUser 1.1.1.31.12.1.2
The user name for this dial connection
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accDialPortConnPhyPort 1.1.1.31.12.1.3
The ifIndex for the physical channel that this call is using
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accDialPortConnLogPort 1.1.1.31.12.1.4
The ifIndex for the logical channel this call is using
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accDialPortConnDir 1.1.1.31.12.1.5
The direction of this call
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in(1), out(2)  

accDialPortConnAuth 1.1.1.31.12.1.6
The IP address of the authenticator for this call. 0.0.0.0 denotes that the call was locally authenticated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

accDialPortConnStart 1.1.1.31.12.1.7
The time stamp; date of call establishment
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

accDialPortConnProf 1.1.1.31.12.1.8
The service profile assigned to this call
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accDialPortConnStack 1.1.1.31.12.1.9
The physical and logical port stack used to terminate this call
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

accDialPortConnAddr 1.1.1.31.12.1.10
The IP address used to communicate to the peer for this call
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

accDialPortConnState 1.1.1.31.12.1.11
If this object is set to 'Disconnect', the entry is Disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disconnect(1)  

accAccessParameter 1.1.1.31.14
OBJECT IDENTIFIER    

accAccessTimer 1.1.1.31.14.1
This object sets the access fucntion on/off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

accAccessCreditDay 1.1.1.31.14.2
This object sets the access credit per day.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

accAccessCreditYear 1.1.1.31.14.3
This object sets the access credit per year.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

accAccessTime 1.1.1.31.14.4
To set access time from and to
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accAccessLimitDate 1.1.1.31.14.5
To set access limit date from and to
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accAccessDay 1.1.1.31.14.6
To set access limit day
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

accAccessDayCreditLeft 1.1.1.31.14.7
This object display the access credit left in the day.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accAccessYearCreditLeft 1.1.1.31.14.8
This object display the access credit left in the year.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppCompressTable 1.1.1.32.21
A table containing PPP Data compression specific variables for PPP compression implementation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppCompressEntry

accPppCompressEntry 1.1.1.32.21.1
PPP data compression table entry containing data compression parameters for a particular PPP port
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppCompressEntry  

accPppCompressIndex 1.1.1.32.21.1.1
The ifindex of the PPP port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppCompressMsgLevel 1.1.1.32.21.1.2
The message level for PPP compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppCompressMethod 1.1.1.32.21.1.3
The administrative status of data compression for this PPP port. None disables data compression and others enabled it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), nego(2), vendor(3), stac-seqn(4), stac-extd(5), stac-none(6), mppc(7)  

accPppCompressStream 1.1.1.32.21.1.4
The stream mode of data compression for this PPP port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER packet(1), stream(2)  

accPppCompressNegoMethodIn 1.1.1.32.21.1.5
The negotiated status of data compression for this PPP port. None disables data compression and others enabled it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), vendor(2), stac-seqn(3), stac-extd(4), stac-none(5), mppc(6)  

accPppCompressNegoMethodOut 1.1.1.32.21.1.6
The negotiated status of data compression for this PPP port. None disables data compression and others enabled it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), vendor(2), stac-seqn(3), stac-extd(4), stac-none(5), mppc(6)  

accPppCompressNegoStreamIn 1.1.1.32.21.1.7
The negotiated stream mode of data compression for this PPP port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER packet(1), stream(2)  

accPppCompressNegoStreamOut 1.1.1.32.21.1.8
The negotiated stream mode of data compression for this PPP port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER packet(1), stream(2)  

accPppCompressStatTable 1.1.1.32.22
Data compression statistics table for PPP ports containing data compression statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccPppCompressStatEntry

accPppCompressStatEntry 1.1.1.32.22.1
Data compression PPP port statistics table entry containing data compression statistics for a particular PPP port
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccPppCompressStatEntry  

accPppCompressStatIndex 1.1.1.32.22.1.1
The interface index of the PPP port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppCompressStatStatusIn 1.1.1.32.22.1.2
The operational status of the PPP port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disc(1), conn(2), sync(3), resync(4)  

accPppCompressStatStatusOut 1.1.1.32.22.1.3
The operational status of the PPP port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disc(1), conn(2), sync(3), resync(4)  

accPppCompressStatAvgCompIn 1.1.1.32.22.1.4
The average compression rato of packets presented for decompression expressed as a percentage between 0 and 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

accPppCompressStatAvgCompOut 1.1.1.32.22.1.5
The average compression rate of packets presented for compression expressed as a percentage between 0 and 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

accPppCompressStatInOctets 1.1.1.32.22.1.6
The total number of compressed octets presented for decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatOutOctets 1.1.1.32.22.1.7
The total number of compressed octets generated after compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatInPackets 1.1.1.32.22.1.8
The total number of uncompressed packets generated by decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatOutPackets 1.1.1.32.22.1.9
The total number of uncompressed packets presented for compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressUnCompInStats 1.1.1.32.22.1.10
The total number of uncompressed packets presented for decompression (i.e., packets which could not be compressed and were therefore received in their uncompressed form).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressUnCompOutStats 1.1.1.32.22.1.11
The total number of uncompressed packets presented for compression which could not be compressed (i.e., the packet expanded). These packets are transmitted in their uncompressed form.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatHdrErrors 1.1.1.32.22.1.12
The number of packets received with invalid compression headers. A header error requires a resynchronization of the history buffers at each end of the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatResyncs 1.1.1.32.22.1.13
The number of resynchronizations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatNoEndMarks 1.1.1.32.22.1.14
The number of packets received with no end marker. Missing end markers require a resynchronization of the history buffers at each end of the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatNoAvailBufs 1.1.1.32.22.1.15
The number of times the PPP port was connected and no history buffer could be allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatRcvResetReqs 1.1.1.32.22.1.16
The number of times the PPP port was connected and no history buffer could be allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatRcvResetAcks 1.1.1.32.22.1.17
The number of times the PPP port was connected and no history buffer could be allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatSndResetReqs 1.1.1.32.22.1.18
The number of times the PPP port was connected and no history buffer could be allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatSndResetAcks 1.1.1.32.22.1.19
The number of times the PPP port was connected and no history buffer could be allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppCompressStatExpandIn 1.1.1.32.22.1.20
The number of incoming packets expanded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppCompressStatExpandOut 1.1.1.32.22.1.21
The number of outgoing packets expanded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppCompressStatDiscardIn 1.1.1.32.22.1.22
The number of incoming packets that are discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accPppCompressStatDiscardOut 1.1.1.32.22.1.23
The number of outgoing packets that are discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accDialPortCompressTable 1.1.1.31.13
A table containing Dial Port Data compression specific varailbes for Dial Port compression implementation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccDialPortCompressEntry

accDialPortCompressEntry 1.1.1.31.13.1
Dial Port data compression table entry containing data compression parameters for a particular Dial Port port
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccDialPortCompressEntry  

accDialPortCompressIndex 1.1.1.31.13.1.1
The ifindex of the Dial Port port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accDialPortCompressMsgLevel 1.1.1.31.13.1.2
The message level for Dial Port compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accDialPortCompressMethod 1.1.1.31.13.1.3
The administrative status of data compression for this Dial Port port. None disables data compression and others enabled it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), nego(2), vendor(3), stac-seqn(4), stac-extd(5), stac-none(6), mppc(7)  

accDialPortCompressStream 1.1.1.31.13.1.4
The stream mode of data compression for this Dial Port port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER packet(1), stream(2)  

accDialPortCompressNegoMethodIn 1.1.1.31.13.1.5
The negotiated status of data compression for for incoming packets for this Dial Port port. None disables data compression and others enabled it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), vendor(2), stac-seqn(3), stac-extd(4), stac-none(5), mppc(6)  

accDialPortCompressNegoMethodOut 1.1.1.31.13.1.6
The negotiated status of data compression for outgoing packets for this Dial Port port. None disables data compression and others enabled it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), vendor(2), stac-seqn(3), stac-extd(4), stac-none(5), mppc(6)  

accDialPortCompressNegoStreamIn 1.1.1.31.13.1.7
The negotiated stream mode of data compression for this Dial Port port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER packet(1), stream(2)  

accDialPortCompressNegoStreamOut 1.1.1.31.13.1.8
The negotiated stream mode of data compression for this Dial Port port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER packet(1), stream(2)  

accDodTraps 1.1.1.31.15
OBJECT IDENTIFIER    

accDodTrapMsg 1.1.1.31.15.1
DOD Trap Message
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

accMlPppCompressTable 1.1.1.9.7
A table containing Multilink group Data compression specific variables for Multilink group compression implementation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccMlPppCompressEntry

accMlPppCompressEntry 1.1.1.9.7.1
Multilink group data compression table entry containing data compression parameters for a particular Multilink group port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccMlPppCompressEntry  

accMlPppCompressIndex 1.1.1.9.7.1.1
The ifindex of the Multilink group port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accMlPppCompressMsgLevel 1.1.1.9.7.1.2
The message level for Multilink group compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accMlPppCompressMethod 1.1.1.9.7.1.3
The administrative status of data compression for this Multilink group port. None disables data compression and others enabled it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), nego(2), vendor(3), stac-seqn(4), stac-extd(5), stac-none(6), mppc(7)  

accMlPppCompressStream 1.1.1.9.7.1.4
The stream mode of data compression for this Multilink group port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER packet(1), stream(2)  

accMlPppCompressNegoMethodIn 1.1.1.9.7.1.5
The negotiated status of data compression for this Multilink group port. None disables data compression and others enabled it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), vendor(2), stac-seqn(3), stac-extd(4), stac-none(5), mppc(6)  

accMlPppCompressNegoMethodOut 1.1.1.9.7.1.6
The negotiated status of data compression for this Multilink group port. None disables data compression and others enabled it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), vendor(2), stac-seqn(3), stac-extd(4), stac-none(5), mppc(6)  

accMlPppCompressNegoStreamIn 1.1.1.9.7.1.7
The negotiated stream mode of data compression for this Multilink group port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER packet(1), stream(2)  

accMlPppCompressNegoStreamOut 1.1.1.9.7.1.8
The negotiated stream mode of data compression for this Multilink group port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER packet(1), stream(2)  

accMlPppCompressStatTable 1.1.1.9.8
Data compression statistics table for Multilink group ports containing data compression statistics
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccMlPppCompressStatEntry

accMlPppCompressStatEntry 1.1.1.9.8.1
Data compression Multilink group port statistics table entry containing data compression statistics for a particular Multilink group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AccMlPppCompressStatEntry  

accMlPppCompressStatIndex 1.1.1.9.8.1.1
The interface index of the Multilink group
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

accMlPppCompressStatStatus 1.1.1.9.8.1.2
The operational status of the Multilink group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disc(1), conn(2), sync(3), resync(4)  

accMlPppCompressStatAvgCompIn 1.1.1.9.8.1.3
The average compression rato of packets presented for decompression expressed as a percentage between 0 and 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

accMlPppCompressStatAvgCompOut 1.1.1.9.8.1.4
The average compression rate of packets presented for compression expressed as a percentage between 0 and 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

accMlPppCompressStatInOctets 1.1.1.9.8.1.5
The total number of compressed octets presented for decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatOutOctets 1.1.1.9.8.1.6
The total number of compressed octets generated after compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatInPackets 1.1.1.9.8.1.7
The total number of uncompressed packets generated by decompression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatOutPackets 1.1.1.9.8.1.8
The total number of uncompressed packets presented for compression.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressUnCompInStats 1.1.1.9.8.1.9
The total number of uncompressed packets presented for decompression (i.e., packets which could not be compressed and were therefore received in their uncompressed form).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressUnCompOutStats 1.1.1.9.8.1.10
The total number of uncompressed packets presented for compression which could not be compressed (i.e., the packet expanded). These packets are transmitted in their uncompressed form.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatHdrErrors 1.1.1.9.8.1.11
The number of packets received with invalid compression headers. A header error requires a resynchronization of the history buffers at each end of the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatResyncs 1.1.1.9.8.1.12
The number of resynchronizations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatNoEndMarks 1.1.1.9.8.1.13
The number of packets received with no end marker. Missing end markers require a resynchronization of the history buffers at each end of the link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatNoAvailBufs 1.1.1.9.8.1.14
The number of times the Multilink group was connected and no history buffer could be allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatRcvResetReqs 1.1.1.9.8.1.15
The number of times the Multilink group was connected and no history buffer could be allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatRcvResetAcks 1.1.1.9.8.1.16
The number of times the Multilink group was connected and no history buffer could be allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatSndResetReqs 1.1.1.9.8.1.17
The number of times the Multilink group was connected and no history buffer could be allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accMlPppCompressStatSndResetAcks 1.1.1.9.8.1.18
The number of times the Multilink group was connected and no history buffer could be allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

accPppUnIdentifiedSourceTrap1 1
Indicates that LCP is in authentication phase. Incoming authentication has been negotiated but there is no authentication source. We should never get here, but for some unknown reason on rare occasions we do. Rather than panic, we will generate a trap message SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accPppTrapMsg } PCAUSE-DEFAULT: 4
TRAP-TYPE    

accPppLoopBackTrap2 2
Indicates that loopback has been found SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accPppTrapMsg } PCAUSE-DEFAULT: 6
TRAP-TYPE    

accPppCallBackTrap3 3
PPP: Callback failied SEVERITY-DEFAULT: Major EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accPppTrapMsg } PCAUSE-DEFAULT: 6
TRAP-TYPE    

accDodPasswdTrap 1
Indicates that Dial port was found but the password didn't match and hence the information will not be forwarded to RADIUS. SEVERITY-DEFAULT: Indeterminate EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 4
TRAP-TYPE    

accPppAuthDenTrap 2
Indicates that either the user password not found or ppp authentication denied for the user SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 4
TRAP-TYPE    

accPppAuthNakTrap 3
PPP authentication failed for various reasons, such as: Dial port is not available or Invalid PAP password or CHAP secret or Port not configured to accept incoming call or Conflicting authentication methods or Cannot accept call on this physical port SEVERITY-DEFAULT: Indeterminate EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 4
TRAP-TYPE    

accDodDialTrap 4
Indicates that while Clearing the current call and searching for work, it is found that work has been done. SEVERITY-DEFAULT: Warning EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 4
TRAP-TYPE    

accDodNoCktTrap 5
Any hunt groups referenced by dial ports need to be expanded here. It also happens during the phase after ISDN NFAS groups have been initialized; It also happens when a dynamically installed dial port acquires a hunt group. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 6
TRAP-TYPE    

accDodPrtBumpTrap 6
Indiacates that one bump port is found that has lower priority that is using one of the physical ports configured for this dial port. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 46
TRAP-TYPE    

accPhyPrtNotAvailTrap 7
Acquiring physical port failed. The physical port admin state is down or the physical port is not available. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 4 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 56
TRAP-TYPE    

accDodCompressionTrap 8
Dial Port Compression (CCP) can't be set for X.25 Dial Port. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 4 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 56
TRAP-TYPE    

accPortInUseTrap 9
Dial port is in use, cannot change CCP parameters. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 2 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 56
TRAP-TYPE    

accDodMaxPapPasswdTrap 10
Indicates that the password entered by user is greater than the maximum length for the PAP password. SEVERITY-DEFAULT: Indeterminate EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 253
TRAP-TYPE    

accDodNeedResetTrap 11
Dial port count change requires reset. SEVERITY-DEFAULT: Minor EVENTTYPE-DEFAULT: 10 ADDITIONAL-TEXT-VARIABLES: { accTrapLogSeqNum,accDodTrapMsg } PCAUSE-DEFAULT: 1
TRAP-TYPE