A3COM-SWITCHING-SYSTEMS-MIB

File: A3COM-SWITCHING-SYSTEMS-MIB.mib (159190 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

enterprises Counter Gauge
IpAddress DisplayString OBJECT-TYPE
TRAP-TYPE

Defined Types

RowStatus  
INTEGER active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6)    

A3ComSysStorageType  
INTEGER 1..3    

A3ComSysAddressType  
INTEGER 1..2    

A3ComSysResourceType  
INTEGER 1..3    

A3ComSysResourceBitMask  
OCTET STRING Size(4)    

IpxNetworkNumber  
OCTET STRING Size(4)    

ATNetworkNumber  
OCTET STRING Size(2)    

ATName  
OCTET STRING Size(0..32)    

DdpNodeAddress  
OCTET STRING Size(3)    

MacAddress  
OCTET STRING Size(6)    

A3ComSysSystemLogEntry  
SEQUENCE    
  a3ComSysSystemLogIndex INTEGER
  a3ComSysSystemLogSeverityLevel INTEGER
  a3ComSysSystemLogDateTime DisplayString
  a3ComSysSystemLogFacility INTEGER
  a3ComSysSystemLogMessage DisplayString

A3ComSysSlotEntry  
SEQUENCE    
  a3ComSysSlotIndex INTEGER
  a3ComSysSlotBoardType INTEGER
  a3ComSysSlotBoardRevision OCTET STRING
  a3ComSysSlotBoardStatus INTEGER
  a3ComSysSlotBoardName DisplayString
  a3ComSysSlotBoardNameAbbrev DisplayString
  a3ComSysSlotEthernetPortCount INTEGER
  a3ComSysSlotFddiMacCount INTEGER
  a3ComSysSlotFddiPortCount INTEGER
  a3ComSysSlotOvertemperature INTEGER
  a3ComSysSlotTokenRingPortCount INTEGER
  a3ComSysSlotBoardRevStr DisplayString
  a3ComSysSlotConverterBad INTEGER

A3ComSysPowerSupplyStatusEntry  
SEQUENCE    
  a3ComSysPowerSupplyStatusIndex INTEGER
  a3ComSysPowerSupplyStatus INTEGER
  a3ComSysPowerSupplyStatusSupported INTEGER

A3ComSysSnmpInternalProxyEntry  
SEQUENCE    
  a3ComSysSnmpInternalProxyAgentId INTEGER
  a3ComSysSnmpInternalProxyAccessClass INTEGER
  a3ComSysSnmpInternalProxyCommunity OCTET STRING

A3ComSysAgentTrapDescriptionTableEntry  
SEQUENCE    
  a3ComSysAgentTrapDescriptionIndex INTEGER
  a3ComSysAgentTrapEnterprise OBJECT IDENTIFIER
  a3ComSysAgentTrapNumber INTEGER

A3ComSysAgentTrapDestinationTableEntry  
SEQUENCE    
  a3ComSysAgentTrapDestinationAddressType INTEGER
  a3ComSysAgentTrapDestinationAddress OCTET STRING
  a3ComSysAgentTrapDestinationTrapMask OCTET STRING
  a3ComSysAgentTrapDestinationEntryStatus INTEGER

A3ComSysInterfaceLocationEntry  
SEQUENCE    
  a3ComSysInterfaceLocationIfIndex INTEGER
  a3ComSysInterfaceLocationInterfaceType INTEGER
  a3ComSysInterfaceLocationType INTEGER
  a3ComSysInterfaceLocationTypeIndex INTEGER
  a3ComSysInterfaceLocationLocalIndex INTEGER
  a3ComSysInterfaceLocationSystemModuleIndex INTEGER

A3ComSysEthernetPortEntry  
SEQUENCE    
  a3ComSysEthernetPortIndex INTEGER
  a3ComSysEthernetPortIfIndex INTEGER
  a3ComSysEthernetPortLabel DisplayString
  a3ComSysEthernetPortLinkStatus INTEGER
  a3ComSysEthernetPortType INTEGER

A3ComSysEthernetPortRateEntry  
SEQUENCE    
  a3ComSysEthernetPortRateIndex INTEGER
  a3ComSysEthernetPortRateByteReceiveRate INTEGER
  a3ComSysEthernetPortRatePeakByteReceiveRate INTEGER
  a3ComSysEthernetPortRateFrameReceiveRate INTEGER
  a3ComSysEthernetPortRatePeakFrameReceiveRate INTEGER
  a3ComSysEthernetPortRateByteTransmitRate INTEGER
  a3ComSysEthernetPortRatePeakByteTransmitRate INTEGER
  a3ComSysEthernetPortRateFrameTransmitRate INTEGER
  a3ComSysEthernetPortRatePeakFrameTransmitRate INTEGER

A3ComSysSmtFddiMacBeaconEntry  
SEQUENCE    
  a3ComSysSmtFddiMacBeaconSmtIndex INTEGER
  a3ComSysSmtFddiMacBeaconIndex INTEGER
  a3ComSysSmtFddiMacBeaconHistory OCTET STRING

A3ComSysSmtFddiMacRateEntry  
SEQUENCE    
  a3ComSysSmtFddiMacRateSmtIndex INTEGER
  a3ComSysSmtFddiMacRateIndex INTEGER
  a3ComSysSmtFddiMacRateByteReceiveRate INTEGER
  a3ComSysSmtFddiMacRatePeakByteReceiveRate INTEGER
  a3ComSysSmtFddiMacRateFrameReceiveRate INTEGER
  a3ComSysSmtFddiMacRatePeakFrameReceiveRate INTEGER
  a3ComSysSmtFddiMacRateByteTransmitRate INTEGER
  a3ComSysSmtFddiMacRatePeakByteTransmitRate INTEGER
  a3ComSysSmtFddiMacRateFrameTransmitRate INTEGER
  a3ComSysSmtFddiMacRatePeakFrameTransmitRate INTEGER

A3ComSysSmtFddiPortEntry  
SEQUENCE    
  a3ComSysSmtFddiPortSmtIndex INTEGER
  a3ComSysSmtFddiPortIndex INTEGER
  a3ComSysSmtFddiPortLocationType INTEGER
  a3ComSysSmtFddiPortLocationTypeIndex INTEGER
  a3ComSysSmtFddiPortLocationLocalIndex INTEGER
  a3ComSysSmtFddiPortLabel DisplayString

A3ComSysSmtFddiMacLocationEntry  
SEQUENCE    
  a3ComSysSmtFddiMacLocationSmtIndex INTEGER
  a3ComSysSmtFddiMacLocationIndex INTEGER
  a3ComSysSmtFddiMacCurrentLocation INTEGER
  a3ComSysSmtFddiMacRequestedLocation INTEGER
  a3ComSysSmtFddiMacAvailableLocation INTEGER

A3ComSysSmtFddiMacStationEntry  
SEQUENCE    
  a3ComSysSmtFddiMacStationSmtIndex INTEGER
  a3ComSysSmtFddiMacStationIndex INTEGER
  a3ComSysSmtFddiMacCurrentStation INTEGER
  a3ComSysSmtFddiMacRequestedStation INTEGER
  a3ComSysSmtFddiMacAvailableStations INTEGER

A3ComSysSmtFddiPortStationEntry  
SEQUENCE    
  a3ComSysSmtFddiPortStationSmtIndex INTEGER
  a3ComSysSmtFddiPortStationIndex INTEGER
  a3ComSysSmtFddiPortCurrentStation INTEGER
  a3ComSysSmtFddiPortRequestedStation INTEGER
  a3ComSysSmtFddiPortAvailableStations INTEGER

A3ComSysBridgeEntry  
SEQUENCE    
  a3ComSysBridgeIndex INTEGER
  a3ComSysBridgePortCount INTEGER
  a3ComSysBridgeAddressTableSize INTEGER
  a3ComSysBridgeAddressTableCount INTEGER
  a3ComSysBridgeAddressTablePeakCount INTEGER
  a3ComSysBridgeAddressThreshold INTEGER
  a3ComSysBridgeMode INTEGER
  a3ComSysBridgeBackbonePort INTEGER
  a3ComSysBridgeIpFragmentationEnabled INTEGER
  a3ComSysBridgeTrFddiTranslationMode INTEGER
  a3ComSysBridgeSTPGroupAddress OCTET STRING
  a3ComSysBridgeSTPEnable INTEGER
  a3ComSysBridgeIpxSnapTranslationEnable INTEGER
  a3ComSysBridgeLowLatencyEnable INTEGER
  a3ComSysBridgeVlanMode INTEGER

A3ComSysBridgePortEntry  
SEQUENCE    
  a3ComSysBridgePortBridgeIndex INTEGER
  a3ComSysBridgePortIndex INTEGER
  a3ComSysBridgePortIfIndex INTEGER
  a3ComSysBridgePortReceiveMulticastLimit INTEGER
  a3ComSysBridgePortAddressAction INTEGER
  a3ComSysBridgePortSpanningTreeFrameReceivedCounts Counter
  a3ComSysBridgePortReceiveBlockedDiscards Counter
  a3ComSysBridgePortReceiveMulticastLimitExceededs Counter
  a3ComSysBridgePortReceiveMulticastLimitExceededDiscards Counter
  a3ComSysBridgePortReceiveSecurityDiscards Counter
  a3ComSysBridgePortReceiveUnknownDiscards Counter
  a3ComSysBridgePortReceiveOtherDiscards Counter
  a3ComSysBridgePortReceiveErrorDiscards Counter
  a3ComSysBridgePortSameSegmentDiscards Counter
  a3ComSysBridgePortTransmitBlockedDiscards Counter
  a3ComSysBridgePortReceiveAllPathFilteredFrames Counter
  a3ComSysBridgePortReceiveMulticastPathFilteredFrames Counter
  a3ComSysBridgePortTransmitAllPathFilteredFrames Counter
  a3ComSysBridgePortTransmitMulticastPathFilteredFrames Counter
  a3ComSysBridgePortForwardedUnicastFrames Counter
  a3ComSysBridgePortForwardedUnicastOctets Counter
  a3ComSysBridgePortForwardedMulticastFrames Counter
  a3ComSysBridgePortForwardedMulticastOctets Counter
  a3ComSysBridgePortFloodedUnicastFrames Counter
  a3ComSysBridgePortFloodedUnicastOctets Counter
  a3ComSysBridgePortStpMode INTEGER
  a3ComSysBridgePortReceiveMulticastLimitFrameType INTEGER
  a3ComSysBridgePortForwardedFrames Counter
  a3ComSysBridgePortReceiveMulticastLimitMultiplier INTEGER

A3ComSysBridgePortAddressEntry  
SEQUENCE    
  a3ComSysBridgePortAddressBridgeIndex INTEGER
  a3ComSysBridgePortAddressPortIndex INTEGER
  a3ComSysBridgePortAddressIndex INTEGER
  a3ComSysBridgePortAddressRemoteAddress OCTET STRING
  a3ComSysBridgePortAddressType INTEGER
  a3ComSysBridgePortAddressIsStatic INTEGER
  a3ComSysBridgePortAddressStaticPort INTEGER
  a3ComSysBridgePortAddressAge INTEGER

A3ComSysNetworkAnalyzerTableEntry  
SEQUENCE    
  a3ComSysNetworkAnalyzerBridgeIndex INTEGER
  a3ComSysNetworkAnalyzerBridgePortIndex INTEGER
  a3ComSysNetworkAnalyzerPhysicalAddress OCTET STRING
  a3ComSysNetworkAnalyzerStatus INTEGER

A3ComSysNetworkPortMonitorTableEntry  
SEQUENCE    
  a3ComSysNetworkPortMonitorBridgeIndex INTEGER
  a3ComSysNetworkPortMonitorBridgePortIndex INTEGER
  a3ComSysNetworkPortMonitorAnalyzerAddress OCTET STRING
  a3ComSysNetworkPortMonitorStatus INTEGER

A3ComSysTokenRingPortEntry  
SEQUENCE    
  a3ComSysTokenRingPortIndex INTEGER
  a3ComSysTokenRingPortIfIndex INTEGER
  a3ComSysTokenRingPortLabel DisplayString
  a3ComSysTokenRingPortInsertStatus INTEGER
  a3ComSysTokenRingPortType INTEGER
  a3ComSysTokenRingPortMode INTEGER
  a3ComSysTokenRingPortSpeed INTEGER
  a3ComSysTokenRingPortLineErrors Counter
  a3ComSysTokenRingPortBurstErrors Counter
  a3ComSysTokenRingPortACErrors Counter
  a3ComSysTokenRingPortAbortTransErrors Counter
  a3ComSysTokenRingPortInternalErrors Counter
  a3ComSysTokenRingPortLostFrameErrors Counter
  a3ComSysTokenRingPortReceiveCongestionErrors Counter
  a3ComSysTokenRingPortFrameCopiedErrors Counter
  a3ComSysTokenRingPortTokenErrors Counter
  a3ComSysTokenRingPortSoftErrors Counter
  a3ComSysTokenRingPortHardErrors Counter
  a3ComSysTokenRingPortTransmitBeacons Counter
  a3ComSysTokenRingPortLobeWires Counter
  a3ComSysTokenRingPortRemoves Counter
  a3ComSysTokenRingPortSingles Counter
  a3ComSysTokenRingPortFreqErrors Counter
  a3ComSysTokenRingPortRingStatus INTEGER

A3ComSysFtTableEntry  
SEQUENCE    
  a3ComSysFtIndex INTEGER
  a3ComSysFtDirection INTEGER
  a3ComSysFtLocalStorageType A3ComSysStorageType
  a3ComSysFtLocalResourceType A3ComSysResourceType
  a3ComSysFtLocalResourceMask A3ComSysResourceBitMask
  a3ComSysFtLocalResourceAttribute OBJECT IDENTIFIER
  a3ComSysFtRemoteAddressType A3ComSysAddressType
  a3ComSysFtRemoteAddress OCTET STRING
  a3ComSysFtRemoteFileName DisplayString
  a3ComSysFtRemoteUserName DisplayString
  a3ComSysFtRemoteUserPassword OCTET STRING
  a3ComSysFtForceTransfer INTEGER
  a3ComSysFtBytesTransferred Counter
  a3ComSysFtStatus INTEGER
  a3ComSysFtDetailedStatus OBJECT IDENTIFIER
  a3ComSysFtDetailedStatusString DisplayString
  a3ComSysFtOwnerString DisplayString
  a3ComSysFtRowStatus RowStatus

A3ComSysIpInterfaceEntry  
SEQUENCE    
  a3ComSysIpInterfaceIpStackIndex INTEGER
  a3ComSysIpInterfaceAddr IpAddress
  a3ComSysIpInterfaceNetMask IpAddress
  a3ComSysIpInterfaceIndex INTEGER
  a3ComSysIpInterfaceBcastAddr INTEGER
  a3ComSysIpInterfaceCost INTEGER
  a3ComSysIpInterfaceStatus RowStatus

A3ComSysIpxInterfaceEntry  
SEQUENCE    
  a3ComSysIpxInterfaceIpxStackIndex INTEGER
  a3ComSysIpxInterfaceNetNumber IpxNetworkNumber
  a3ComSysIpxInterfaceIfIndex INTEGER
  a3ComSysIpxInterfaceCost INTEGER
  a3ComSysIpxInterfaceFrameType INTEGER
  a3ComSysIpxInterfaceStatus RowStatus

A3ComSysAtInterfaceEntry  
SEQUENCE    
  a3ComSysAtInterfaceAtStackIndex INTEGER
  a3ComSysAtInterfaceNetAddress DdpNodeAddress
  a3ComSysAtInterfaceType INTEGER
  a3ComSysAtInterfaceNetStart ATNetworkNumber
  a3ComSysAtInterfaceNetEnd ATNetworkNumber
  a3ComSysAtInterfaceZoneDefault ATName
  a3ComSysAtInterfaceZone1 ATName
  a3ComSysAtInterfaceZone2 ATName
  a3ComSysAtInterfaceZone3 ATName
  a3ComSysAtInterfaceZone4 ATName
  a3ComSysAtInterfaceZone5 ATName
  a3ComSysAtInterfaceZone6 ATName
  a3ComSysAtInterfaceZone7 ATName
  a3ComSysAtInterfaceZone8 ATName
  a3ComSysAtInterfaceZone9 ATName
  a3ComSysAtInterfaceZone10 ATName
  a3ComSysAtInterfaceZone11 ATName
  a3ComSysAtInterfaceZone12 ATName
  a3ComSysAtInterfaceZone13 ATName
  a3ComSysAtInterfaceZone14 ATName
  a3ComSysAtInterfaceZone15 ATName
  a3ComSysAtInterfaceIfIndex INTEGER
  a3ComSysAtInterfaceState INTEGER
  a3ComSysAtInterfaceStatus RowStatus

A3ComSysModuleCardInfoEntry  
SEQUENCE    
  a3ComSysModuleCardInfoIndex INTEGER
  a3ComSysModuleCardInfoFamily INTEGER
  a3ComSysModuleCardInfoGenericType INTEGER
  a3ComSysModuleCardInfoSpecificType INTEGER
  a3ComSysModuleCardInfoPartNumber DisplayString
  a3ComSysModuleCardInfoManufacturingDate DisplayString
  a3ComSysModuleCardInfoModuleSerialNumber DisplayString
  a3ComSysModuleCardInfoTLASerialNumber DisplayString
  a3ComSysModuleCardInfo3CNumber DisplayString
  a3ComSysModuleCardInfoICTTestStatus INTEGER
  a3ComSysModuleCardInfoICTTestRevision DisplayString
  a3ComSysModuleCardInfoSystemTestStatus INTEGER
  a3ComSysModuleCardInfoFunctionalTestStatus INTEGER
  a3ComSysModuleCardInfoFunctionalTestRevision DisplayString
  a3ComSysModuleCardInfoBoardRevision DisplayString
  a3ComSysModuleCardInfoRuntimeHours INTEGER

A3ComSysDiagnosticsInfoEntry  
SEQUENCE    
  a3ComSysDiagnosticsInfoIndex INTEGER
  a3ComSysDiagnosticsInfoPOVDiagnosticsRevision DisplayString
  a3ComSysDiagnosticsInfoExtendedDiagnosticsRevision DisplayString
  a3ComSysDiagnosticsInfoDiagnosticFailureCode DisplayString
  a3ComSysDiagnosticsInfoDiagnosticFailureDateTime DisplayString
  a3ComSysDiagnosticsInfoDiagnosticFailureSlotNumber INTEGER
  a3ComSysDiagnosticsInfoDiagnosticFailureCounter INTEGER
  a3ComSysDiagnosticsInfoDiagnosticFieldDOACounter INTEGER

Defined Values

a3Com 1.3.6.1.4.1.43
OBJECT IDENTIFIER    

switchingSystems-mib 1.3.6.1.4.1.43.29
OBJECT IDENTIFIER    

switchingSystemsMibGroups 1.3.6.1.4.1.43.29.4
OBJECT IDENTIFIER    

switchingSystemsFddiMibGroups 1.3.6.1.4.1.43.29.10
OBJECT IDENTIFIER    

a3ComSysSystem 1.3.6.1.4.1.43.29.4.1
OBJECT IDENTIFIER    

a3ComSysSlot 1.3.6.1.4.1.43.29.4.2
OBJECT IDENTIFIER    

a3ComSysControlPanel 1.3.6.1.4.1.43.29.4.3
OBJECT IDENTIFIER    

a3ComSysPowerSupply 1.3.6.1.4.1.43.29.4.4
OBJECT IDENTIFIER    

a3ComSysSnmp 1.3.6.1.4.1.43.29.4.5
OBJECT IDENTIFIER    

a3ComSysAgent 1.3.6.1.4.1.43.29.4.6
OBJECT IDENTIFIER    

a3ComSysInterface 1.3.6.1.4.1.43.29.4.7
OBJECT IDENTIFIER    

a3ComSysEthernetPort 1.3.6.1.4.1.43.29.4.8
OBJECT IDENTIFIER    

a3ComSysSmt 1.3.6.1.4.1.43.29.4.9
OBJECT IDENTIFIER    

a3ComSysBridge 1.3.6.1.4.1.43.29.4.10
OBJECT IDENTIFIER    

a3ComSysIpRouter 1.3.6.1.4.1.43.29.4.11
OBJECT IDENTIFIER    

a3ComSysNetworkMonitor 1.3.6.1.4.1.43.29.4.12
OBJECT IDENTIFIER    

a3ComSysTokenRingPort 1.3.6.1.4.1.43.29.4.13
OBJECT IDENTIFIER    

a3ComSysFtGroup 1.3.6.1.4.1.43.29.4.14
OBJECT IDENTIFIER    

a3ComSysIpGroup 1.3.6.1.4.1.43.29.4.15
OBJECT IDENTIFIER    

a3ComSysIpxGroup 1.3.6.1.4.1.43.29.4.16
OBJECT IDENTIFIER    

a3ComSysAppleTalkGroup 1.3.6.1.4.1.43.29.4.17
OBJECT IDENTIFIER    

a3ComSysModuleCardGroup 1.3.6.1.4.1.43.29.4.18
OBJECT IDENTIFIER    

a3ComSysDiagnosticsGroup 1.3.6.1.4.1.43.29.4.19
OBJECT IDENTIFIER    

a3ComSysSystemId 1.3.6.1.4.1.43.29.4.1.1
The unique identifier assigned to this system during manufacturing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemType 1.3.6.1.4.1.43.29.4.1.2
The type of system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), lanplex6000(2), lanplex2000(3), coreBuilder3500(4), coreBuilder9400(5), superStack3900(6), superStack9300(7)  

a3ComSysSystemName 1.3.6.1.4.1.43.29.4.1.3
The text string describing this system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

a3ComSysSystemManufacturer 1.3.6.1.4.1.43.29.4.1.4
The text string describing the manufacturer of this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

a3ComSysSystemHardwareRevision 1.3.6.1.4.1.43.29.4.1.5
The revision level of the system, contained in two octets. The first octet indicates the artwork revision, and the second octet indicates the rework level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

a3ComSysSystemMemorySize 1.3.6.1.4.1.43.29.4.1.6
The amount of memory (RAM), in bytes, present on the system processor board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemFlashMemorySize 1.3.6.1.4.1.43.29.4.1.7
The amount of flash memory, in bytes, present on the system processor board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemNvMemorySize 1.3.6.1.4.1.43.29.4.1.8
The amount of non-volatile memory, in bytes, present on the system processor board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemSoftwareRevision 1.3.6.1.4.1.43.29.4.1.9
The revision number of the Switching Systems software. Each byte indicates the following: byte 0: major release number. byte 1: minor release number. byte 2: update number. byte 3: bits 7-6: release type. bits 5-0: supplemental identifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

a3ComSysSystemBuildTime 1.3.6.1.4.1.43.29.4.1.10
The build time of the system software.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

a3ComSysSystemSnmpRevision 1.3.6.1.4.1.43.29.4.1.11
The revision number of the SNMP agent implementation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemRequestedSnmpMode 1.3.6.1.4.1.43.29.4.1.12
This object describes the requested SNMP mode for the system. The value of this object indicates the mode that will become effective following a reboot of the system. Note that only a subset of the above values may be valid for some systems.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER singleAgentMode(1), multiAgentMode(2)  

a3ComSysSystemCurrentSnmpMode 1.3.6.1.4.1.43.29.4.1.13
This object describes the currently active SNMP mode for the system. Note that only a subset of the above values may be valid for some systems.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER singleAgentMode(1), multiAgentMode(2)  

a3ComSysSystemAction 1.3.6.1.4.1.43.29.4.1.14
This object, when read, always returns the value other(1). Setting this object to the value reset(2) causes a reset of the system. Setting this object to the value nvReset(3) causes the system's non-volatile configuration to be reset to the default values. The value other(1) is not a vaild value for set operations.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), reset(2), nvReset(3)  

a3ComSysSystemOvertemperature 1.3.6.1.4.1.43.29.4.1.15
This object indicates the current overtemperature status for the system. If the system does not support overtemperature detection, this object returns notSupported.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2), notSupported(3)  

a3ComSysSystemFanFailure 1.3.6.1.4.1.43.29.4.1.16
This object indicates the current fan status for the system. If the system does not support fan failure detection, this object returns notSupported.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2), notSupported(3)  

a3ComSysSystemProtocolMask 1.3.6.1.4.1.43.29.4.1.17
This object is a bit mask that indicates which protocols exist in the software image currently loaded in memory. The value of this OBJECT is a sum. It initially takes on the value 0, then for each protocol bit as defined below, 2 raised to the value of the (bit position - 1) is added to the sum. The following bits are defined: IP_ROUTING 0x00000001 IPX_ROUTING 0x00000002 DDP_ROUTING 0x00000004 A value of 0x00000000 indicates the standard switching software.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemConsoleAccess 1.3.6.1.4.1.43.29.4.1.18
This object determines whether another device can remotely access the system console via Telnet, Rlogin, or modem port. An existing remote session will not be terminated when this value is modified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

a3ComSysSystemConsoleReadPwd 1.3.6.1.4.1.43.29.4.1.19
This object is the console read-access password.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

a3ComSysSystemConsoleWritePwd 1.3.6.1.4.1.43.29.4.1.20
This object is the console write-access password. The read-write community string is required for access to this object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

a3ComSysSystemConsoleAdminPwd 1.3.6.1.4.1.43.29.4.1.21
This object is the console admin-access password. The read-write community string is required for access to this object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

a3ComSysSystemDateTime 1.3.6.1.4.1.43.29.4.1.22
The current date and time as reflected by the system clock in the format mm/dd/yy hh:mm:ss xM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

a3ComSysSystemDSTime 1.3.6.1.4.1.43.29.4.1.23
This parameter specifies the displacement, in minutes, from non-daylight savings time. The a3ComSysDSTime object, along with the a3ComSysTimeZone object, allows the system to support Universal time for network communications spanning different time zones.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -120..120  

a3ComSysSystemTimeZone 1.3.6.1.4.1.43.29.4.1.24
This parameter specifies, in minutes, displacement of the system west of Greenwich. A negative number for this parameter indicates how many minutes displacement east of Greenwich the site is located. A positive number indicates the number of minutes west of Greenwich.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -720..720  

a3ComSysSystemCurrentFddiStationMode 1.3.6.1.4.1.43.29.4.1.25
This object describes the current FDDI station mode for systems that support multi-station mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER singleStationMode(1), multiStationMode(2)  

a3ComSysSystemRequestedFddiStationMode 1.3.6.1.4.1.43.29.4.1.26
This object describes the requested FDDI station mode for systems that support multi-station mode. The requested mode will become current during the next system reboot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER singleStationMode(1), multiStationMode(2)  

a3ComSysSystemLog 1.3.6.1.4.1.43.29.4.1.27
OBJECT IDENTIFIER    

a3ComSysSystemLogEntryCurrentCount 1.3.6.1.4.1.43.29.4.1.27.1
The number of entries currently recorded in the system log.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemLogMaxSize 1.3.6.1.4.1.43.29.4.1.27.2
The maximum number of events that can be recorded in the system log.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemLogSeverityThreshold 1.3.6.1.4.1.43.29.4.1.27.3
This object determines the miminum serverety level of events recorded in the system log. For example, if the a3ComSysSysteLogSeverityThreshold is set to errors(3) than only events which have serverity levels of error(3) or higher will be recorded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER informational(1), warning(2), error(3), fatal(4)  

a3ComSysSystemLogTable 1.3.6.1.4.1.43.29.4.1.27.4
This table provides information on recorded system events.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysSystemLogEntry

a3ComSysSystemLogEntry 1.3.6.1.4.1.43.29.4.1.27.4.1
A system log entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysSystemLogEntry  

a3ComSysSystemLogIndex 1.3.6.1.4.1.43.29.4.1.27.4.1.1
The index of the log entry relative to this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemLogSeverityLevel 1.3.6.1.4.1.43.29.4.1.27.4.1.2
Indicates the severity level of the log entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER information(1), warning(2), error(3), fatal(4)  

a3ComSysSystemLogDateTime 1.3.6.1.4.1.43.29.4.1.27.4.1.3
Indicates the date and time of the log event and is formatted as follows: MM:DD:YY HH:MM:SS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysSystemLogFacility 1.3.6.1.4.1.43.29.4.1.27.4.1.4
The facility which entered the event in the log. fcmlmm(6) represents those events which may be common to the Lanplex Management Module (LMM) and the FDDI Concentrator Module (FCM). lmmfddi(6) represents those events specific to the FDDI portion of the LMM and lmmboard represents general events logged by the LMM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER exception(1), operatingSystem(2), assertion(3), spanningTree(4), fcmlmm(5), lmmfddi(6), lmmboard(7), esm(8), trsm(9), efsm(10), fsm(11), hsi(12)  

a3ComSysSystemLogMessage 1.3.6.1.4.1.43.29.4.1.27.4.1.5
The recorded log message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysSystemBaseMACAddress 1.3.6.1.4.1.43.29.4.1.28
The base MAC address for the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

a3ComSysSystemMACAddressCount 1.3.6.1.4.1.43.29.4.1.29
The number of MAC addresses allocated to this system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemChassisSerialNumber 1.3.6.1.4.1.43.29.4.1.30
The serial number of the chassis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

a3ComSysSystemFPMemorySize 1.3.6.1.4.1.43.29.4.1.31
The amount of frame processor memory (RAM), in bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemBufferSize 1.3.6.1.4.1.43.29.4.1.32
The amount of buffer memory, in bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSlotCount 1.3.6.1.4.1.43.29.4.2.1
The count of slots in the chassis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSlotTable 1.3.6.1.4.1.43.29.4.2.2
A list of slot entries. A single entry exists in this list for each slot in the chassis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysSlotEntry

a3ComSysSlotEntry 1.3.6.1.4.1.43.29.4.2.2.1
A slot entry contains information about a particular slot.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysSlotEntry  

a3ComSysSlotIndex 1.3.6.1.4.1.43.29.4.2.2.1.1
The index of the slot identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSlotBoardType 1.3.6.1.4.1.43.29.4.2.2.1.2
The type of board residing in the slot identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), emptyLocation(2), esmBoard(7), fcmBoard(8), lmmBoard(9), efsmBoard(10), trsmBoard(11), tmmBoard(12), fsmBoard(13), fesmBoard(14)  

a3ComSysSlotBoardRevision 1.3.6.1.4.1.43.29.4.2.2.1.3
The revision number of the board in the slot identified by this entry. If the slot is empty, or the revision is unknown this object returns a zero length string.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..1)  

a3ComSysSlotBoardStatus 1.3.6.1.4.1.43.29.4.2.2.1.4
The status of the board in the slot identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notPresent(1), testing(2), offline(3), online(4)  

a3ComSysSlotBoardName 1.3.6.1.4.1.43.29.4.2.2.1.5
The text string describing the board in the slot identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

a3ComSysSlotBoardNameAbbrev 1.3.6.1.4.1.43.29.4.2.2.1.6
The abbreviation used to describe the board in the slot identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

a3ComSysSlotEthernetPortCount 1.3.6.1.4.1.43.29.4.2.2.1.7
The count of ethernet ports in the slot identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSlotFddiMacCount 1.3.6.1.4.1.43.29.4.2.2.1.8
The count of FDDI MACs in the slot identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSlotFddiPortCount 1.3.6.1.4.1.43.29.4.2.2.1.9
The count of FDDI ports in the slot identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSlotOvertemperature 1.3.6.1.4.1.43.29.4.2.2.1.10
This object indicates the current overtemperature status for the slot. If the slot does not support overtemperature detection, this object returns notSupported.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2), notSupported(3)  

a3ComSysSlotTokenRingPortCount 1.3.6.1.4.1.43.29.4.2.2.1.11
The count of TokenRing ports in the slot identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSlotBoardRevStr 1.3.6.1.4.1.43.29.4.2.2.1.12
This revision number of the board in the slot identified by this entry. If the slot is empty, or the revision is unknown this object returns a zero length string. The format of the string is XX.YY, where the XX is the major revision (artwork), the YY is the minor revision (rework)
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..5)  

a3ComSysSlotConverterBad 1.3.6.1.4.1.43.29.4.2.2.1.13
This object indicates the current status +12V->+5V converter for the slot. If the slot does not support +12V->+5V converter detection, this object returns notSupported.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2), notSupported(3)  

a3ComSysControlPanelHardwareRevision 1.3.6.1.4.1.43.29.4.3.1
An 8-bit value specifying the revision level of the control panel hardware.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

a3ComSysControlPanelSoftwareRevision 1.3.6.1.4.1.43.29.4.3.2
An 8-bit value specifying the revision level of the control panel software.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

a3ComSysControlPanelLines 1.3.6.1.4.1.43.29.4.3.3
The number of lines in the control panel display.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysControlPanelColumns 1.3.6.1.4.1.43.29.4.3.4
The number of columns in the control panel display.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysControlPanelText 1.3.6.1.4.1.43.29.4.3.5
The currently displayed text in the control panel display.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..127)  

a3ComSysControlPanelAccess 1.3.6.1.4.1.43.29.4.3.6
This object determines whether modifications to system configuration are allowed via the Control Panel
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

a3ComSysPowerSupplyCount 1.3.6.1.4.1.43.29.4.4.1
The count of power supplies in the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysPowerSupplyStatusTable 1.3.6.1.4.1.43.29.4.4.2
A list of power supply status entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysPowerSupplyStatusEntry

a3ComSysPowerSupplyStatusEntry 1.3.6.1.4.1.43.29.4.4.2.1
A power supply status entry contains information about a particular power supply.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysPowerSupplyStatusEntry  

a3ComSysPowerSupplyStatusIndex 1.3.6.1.4.1.43.29.4.4.2.1.1
The unique index of the power supply identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysPowerSupplyStatus 1.3.6.1.4.1.43.29.4.4.2.1.2
This object represents the power supply status. The value is a sum. It initially takes on the value 0, then for each type which is active, 2 raised to a power is added to the sum. The powers are according to the following table. For the 6000 Backbone Aggregator an over temp for power supply 1 and power supply 2 will be reported as a power supply 1 Over Temperature Failure, and a fan failure will be reported as a power supply 2 Over Temperature Failure. Failure Type Power AC Failure 0 Plus 5 Failure 1 Plus 12 Failure 2 Over Temperature Failure 3 Power Supply Inserted 4 Power Supply Extracted 5
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysPowerSupplyStatusSupported 1.3.6.1.4.1.43.29.4.4.2.1.3
This object represents the various power supply status types which are supported. The value is a sum. It initially takes on the value 0, then for each type which is supported, 2 raised to a power is added to the sum. The powers are according to the following table: Failure Type Power AC Failure 0 Plus 5 Failure 1 Plus 12 Failure 2 Over Temperature Failure 3 Power Supply Inserted 4 Power Supply Extracted 5 This object used in conjunction with the a3ComSysPowerSupplyStatus object for a given power supply provide a complete picture of the status of the power supply.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSnmpAgentId 1.3.6.1.4.1.43.29.4.5.1
The unique id for this SNMP agent within the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSnmpInternalAgentTrapMask 1.3.6.1.4.1.43.29.4.5.2
This value is a bit string that indicates which traps are enabled for transmit to other agents in the system. The octet string value is treated as a 64-bit integer value. The value is a sum. It initially takes on the value 0, then for each trap which is enabled, 2 raised to the value of (a3ComSysAgentTrapDescriptionIndex - 1) for that trap is added to the sum.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(8)  

a3ComSysSnmpInternalAgentTrapDestinationMask 1.3.6.1.4.1.43.29.4.5.3
A value which indicates to which other agents in the system traps should be sent. The value is a sum. It initially takes on the value 0, then for each agent which is to receive traps, 2 raised to the value of (a3ComSysSnmpAgentId - 1) for that agent is added to the sum. Note that only traps which are enabled according to the value of the a3ComSysSnmpInternalAgentTrapMask object will be forwarded, and that each trap which is forwarded will be transmitted to each agent identified by this mask.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysSnmpProxyInternalRequests 1.3.6.1.4.1.43.29.4.5.4
This object determines if this agent will proxy requests to other agents in the system. If the value of this object is true(1), this agent will proxy requests to other agents in the chassis.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

a3ComSysSnmpInternalProxyRequestMaxAge 1.3.6.1.4.1.43.29.4.5.5
The maximum time, in seconds, an internal proxy request will remain queued waiting for a response before being discarded. Note that when the value of a3ComSysSnmpProxyInternalRequests is false(2), the value of this object is ignored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

a3ComSysSnmpProxyInternalTraps 1.3.6.1.4.1.43.29.4.5.6
This object determines if this agent will generate proxy traps for those traps received from other agents in the system. If the value of this object is true(1), this agent will generate proxy traps for those received from other agents in the chassis. Note that agents will not proxy traps to other agents within the system to prevent looping of traps.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

a3ComSysSnmpInternalProxyTable 1.3.6.1.4.1.43.29.4.5.7
A list of SNMP internal agent proxy entries. An entry in this table exists for each agent in the system that can be reached by this agent via the internal proxy mechanism.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysSnmpInternalProxyEntry

a3ComSysSnmpInternalProxyEntry 1.3.6.1.4.1.43.29.4.5.7.1
An entry identifies the communities available for communicating with another agent in the system via the internal proxy mechanism.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysSnmpInternalProxyEntry  

a3ComSysSnmpInternalProxyAgentId 1.3.6.1.4.1.43.29.4.5.7.1.1
The id of the agent identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSnmpInternalProxyAccessClass 1.3.6.1.4.1.43.29.4.5.7.1.2
The access to MIB objects supported by the agent identified by this entry provided by this agent, when using the community string identified by the corresponding value of a3ComSysSnmpInternalProxyCommunity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER readOnly(1), readWrite(2)  

a3ComSysSnmpInternalProxyCommunity 1.3.6.1.4.1.43.29.4.5.7.1.3
A community which allows access to MIB objects supported by the agent identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

a3ComSysAgentRequestMaxAge 1.3.6.1.4.1.43.29.4.6.1
The maximum time, in seconds, a local SNMP request will remain queued waiting for a response before being discarded.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

a3ComSysAgentProxyRemoteSmtRequests 1.3.6.1.4.1.43.29.4.6.2
This object determines if this agent will proxy SMT requests to other FDDI stations. If the value of this object is true(1), this agent will proxy SMT requests to other stations. Note that only a subset of the above values may be valid for some systems.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

a3ComSysAgentRemoteSmtProxyRequestMaxAge 1.3.6.1.4.1.43.29.4.6.3
The maximum time, in seconds, an SMT proxy request will remain queued waiting for a response before being discarded. Note that when the value of a3ComSysAgentProxyRemoteSmtRequests is false(2), the value of this object is ignored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

a3ComSysAgentProxyRemoteSmtEvents 1.3.6.1.4.1.43.29.4.6.4
This object determines if this agent will generate traps for SMT events occuring at other stations. If the value of this object is true(1), this agent will generate traps for all SMT events, those which occur locally, and those which occur at other stations. If the value of this object is false(2), this agent will only generate traps for events which occur locally. Note that only a subset of the above values may be valid for some systems.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

a3ComSysAgentTrapDescriptionTable 1.3.6.1.4.1.43.29.4.6.5
This table contains a listing of trap descriptions for each trap supported by this agent. This provides a relationship between a trap index, and the trap enterprise oid and trap number for a given trap. In all cases except for the MIB-2 generic traps, the enterprise under which a trap is defined is the same as that appearing in the ENTERPRISE portion of the trap.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysAgentTrapDescriptionTableEntry

a3ComSysAgentTrapDescriptionTableEntry 1.3.6.1.4.1.43.29.4.6.5.1
Information relating a trap index to a specific trap enterprise oid and trap number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysAgentTrapDescriptionTableEntry  

a3ComSysAgentTrapDescriptionIndex 1.3.6.1.4.1.43.29.4.6.5.1.1
A unique index corresponding to the trap described by this entry. This value of this object corresponding to a particular trap will remain constant accross system resets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysAgentTrapEnterprise 1.3.6.1.4.1.43.29.4.6.5.1.2
The enterpise under which the trap identified by this entry is defined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

a3ComSysAgentTrapNumber 1.3.6.1.4.1.43.29.4.6.5.1.3
The number of the trap identified by this entry, within the enterprise where it is defined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysAgentTrapDestinationTable 1.3.6.1.4.1.43.29.4.6.6
This table contains information specifying which traps will be transmitted to a given destination address. The table is indexed by the destination address type and destination address. Each entry in the table with a status of valid identifies a set of traps which, when generated, will be transmitted to the corresponding destination address listed in that entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysAgentTrapDestinationTableEntry

a3ComSysAgentTrapDestinationTableEntry 1.3.6.1.4.1.43.29.4.6.6.1
Information relating a set of traps and a destination address to which each trap in ths set will be transmitted when it is generated. To create a new entry, set a non-existent instance of a3ComSysAgentTrapDestinationTrapMask to a valid value. To remove an entry, set the instance of a3ComSysAgentTrapDestinationEntryStatus for the entry to invalid(2).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysAgentTrapDestinationTableEntry  

a3ComSysAgentTrapDestinationAddressType 1.3.6.1.4.1.43.29.4.6.6.1.1
The type of address identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip(1)  

a3ComSysAgentTrapDestinationAddress 1.3.6.1.4.1.43.29.4.6.6.1.2
The address, of the type specified by the corresponding value of a3ComSysAgentTrapDestinationAddressType, to which the set of traps identified by this entry are to be transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

a3ComSysAgentTrapDestinationTrapMask 1.3.6.1.4.1.43.29.4.6.6.1.3
This value is a bit string that indicates which traps are enabled for the address identified by this entry. The octet string value is treated as a 64-bit value. The value is a sum. It initially takes on the value 0, then for each trap which is enabled, 2 raised to the value of (a3ComSysAgentTrapDescriptionIndex - 1) for that trap is added to the sum. A new entry in the table is created by setting the value of this object for a new destination address type and destination address. Note that an octet string of all zeros is not a valid value for this object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(8)  

a3ComSysAgentTrapDestinationEntryStatus 1.3.6.1.4.1.43.29.4.6.6.1.4
The status of the trap destination table entry. Setting this object to invalid(1) has the effect of removing the corresponding entry from the table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

a3ComSysAgentReadCommunity 1.3.6.1.4.1.43.29.4.6.7
This object is the read community string when access is made via SNMP, see RFC1157.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..48)  

a3ComSysAgentReadWriteCommunity 1.3.6.1.4.1.43.29.4.6.8
This object is the read-write community string when access is made via SNMP, see RFC1157. The read-write community string is required to access this object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..48)  

a3ComSysInterfaceLocationTable 1.3.6.1.4.1.43.29.4.7.1
A list of interface location entries. A single entry exists in this list for each interface managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysInterfaceLocationEntry

a3ComSysInterfaceLocationEntry 1.3.6.1.4.1.43.29.4.7.1.1
An interface location entry describes the location of a particular interface managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysInterfaceLocationEntry  

a3ComSysInterfaceLocationIfIndex 1.3.6.1.4.1.43.29.4.7.1.1.1
The value of the MIB-II ifIndex corresponding to the interface identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysInterfaceLocationInterfaceType 1.3.6.1.4.1.43.29.4.7.1.1.2
The type of the physical implementation of the interface identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), ethernetPort(2), fddiMac(3), tokenringPort(4), atmPort(5)  

a3ComSysInterfaceLocationType 1.3.6.1.4.1.43.29.4.7.1.1.3
The type of location where the interface identified by this entry is physically located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), modularSlot(2), chassis(3), modularCard(4)  

a3ComSysInterfaceLocationTypeIndex 1.3.6.1.4.1.43.29.4.7.1.1.4
The index of the location identified by the corresponding instance of a3ComSysInterfaceLocationType where the interface identified by this entry is physically located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysInterfaceLocationLocalIndex 1.3.6.1.4.1.43.29.4.7.1.1.5
The local index of the interface identified by this entry relative to its type specified by the corresponding value of a3ComSysInterfaceLocationInterfaceType, and the location specified by the corresponding values of a3ComSysInterfaceLocationType and a3ComSysInterfaceLocationTypeIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysInterfaceLocationSystemModuleIndex 1.3.6.1.4.1.43.29.4.7.1.1.6
The system module index of the interface idnetified by this entry. Ths index can be used to acquire the module information from the s2SysModuleCardGroup and the a3ComSysDiagnosticsGroup groups.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortCount 1.3.6.1.4.1.43.29.4.8.1
The count of ethernet ports managed by this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortTable 1.3.6.1.4.1.43.29.4.8.2
A list of ethernet port entries. A single entry exists in this list for each ethernet port managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysEthernetPortEntry

a3ComSysEthernetPortEntry 1.3.6.1.4.1.43.29.4.8.2.1
An ethernet port entry contains information about a particular ethernet port managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysEthernetPortEntry  

a3ComSysEthernetPortIndex 1.3.6.1.4.1.43.29.4.8.2.1.1
The index of the ethernet port identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortIfIndex 1.3.6.1.4.1.43.29.4.8.2.1.2
The value of the MIB-II ifIndex corresponding to the ethernet port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortLabel 1.3.6.1.4.1.43.29.4.8.2.1.3
An ASCII text string describing the ethernet port identified by this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

a3ComSysEthernetPortLinkStatus 1.3.6.1.4.1.43.29.4.8.2.1.4
The current value of the link status for the ethernet port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inActive(2)  

a3ComSysEthernetPortType 1.3.6.1.4.1.43.29.4.8.2.1.5
Specific port type description for the ethernet port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER rj2110BaseT(1), rj4510BaseT(2), st10BaseFL(3), aui(4), bnc10Base2(5), other(6), rj45100BaseT(7), sc100BaseFx(8), untermBnc10Base2(9), sc1000BaseLxSm(10), sc1000BaseLxMm(11), sc1000BaseLxSmMm(12), sc1000BaseLx10km(13), sc1000BaseSx(14), hssdc1000BaseCx(15), db91000BaseCx(16), gbicNotPresent(17), gbic1000BaseCxDb9(18), gbic1000BaseCxHssdc(19), gbic1000BaseLx10Km(20), gbic1000BaseLx(21), gbic1000BaseSx(22), rj451000BaseT(23), port1000NotPresent(24)  

a3ComSysEthernetPortRateTable 1.3.6.1.4.1.43.29.4.8.3
A list of ethernet port rate entries. A single entry exists in this list for each ethernet port, managed by this agent, which supports rate information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysEthernetPortRateEntry

a3ComSysEthernetPortRateEntry 1.3.6.1.4.1.43.29.4.8.3.1
An ethernet port rate entry contains rate statistics for a particular ethernet port managed by this agent. Rate statistics are calculated based on a one second sampling interval.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysEthernetPortRateEntry  

a3ComSysEthernetPortRateIndex 1.3.6.1.4.1.43.29.4.8.3.1.1
The index of the ethernet port identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortRateByteReceiveRate 1.3.6.1.4.1.43.29.4.8.3.1.2
The average number of bytes received per second by the ethernet port identified by this entry during the most recent sampling period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortRatePeakByteReceiveRate 1.3.6.1.4.1.43.29.4.8.3.1.3
The peak value of a3ComSysEthernetPortRateByteReceiveRate since the system was last initialized for the ethernet port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortRateFrameReceiveRate 1.3.6.1.4.1.43.29.4.8.3.1.4
The average number of frames received per second by the ethernet port identified by this entry during the most recent sampling period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortRatePeakFrameReceiveRate 1.3.6.1.4.1.43.29.4.8.3.1.5
The peak value of a3ComSysEthernetPortRateFrameReceiveRate since the system was last initialized for the ethernet port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortRateByteTransmitRate 1.3.6.1.4.1.43.29.4.8.3.1.6
The average number of bytes transmitted per second by the ethernet port identified by this entry during the most recent sampling period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortRatePeakByteTransmitRate 1.3.6.1.4.1.43.29.4.8.3.1.7
The peak value of a3ComSysEthernetPortRateByteTransmitRate since the system was last initialized for the ethernet port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortRateFrameTransmitRate 1.3.6.1.4.1.43.29.4.8.3.1.8
The average number of frames transmitted per second by the ethernet port identified by this entry during the most recent sampling period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysEthernetPortRatePeakFrameTransmitRate 1.3.6.1.4.1.43.29.4.8.3.1.9
The peak value of a3ComSysEthernetPortRateFrameTransmitRate since the system was last initialized for the ethernet port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtCount 1.3.6.1.4.1.43.29.4.9.1
The count of SMTs managed by this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacBeaconTable 1.3.6.1.4.1.43.29.4.9.4
A list of FDDI MAC beacon entries. A single entry exists in this list for each FDDI MAC, managed by this agent, which supports MAC beacon history.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysSmtFddiMacBeaconEntry

a3ComSysSmtFddiMacBeaconEntry 1.3.6.1.4.1.43.29.4.9.4.1
An FDDI MAC beacon entry contains information about a particular FDDI MAC's beacon history.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysSmtFddiMacBeaconEntry  

a3ComSysSmtFddiMacBeaconSmtIndex 1.3.6.1.4.1.43.29.4.9.4.1.1
The index of the SMT instance identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacBeaconIndex 1.3.6.1.4.1.43.29.4.9.4.1.2
The index of the FDDI MAC identified by this entry, within the SMT identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacBeaconHistory 1.3.6.1.4.1.43.29.4.9.4.1.3
This object gives a history of the most recent beacon information received on the FDDI MAC identified by this entry. It can contain up to a maximum of eight records. Each record is of the form: source MAC: 6 bytes beacon data length: 2 bytes. beacon data: 0-16 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

a3ComSysSmtFddiMacRateTable 1.3.6.1.4.1.43.29.4.9.5
A list of FDDI MAC rate entries. A single entry exists in this list for each FDDI MAC, managed by this agent, which supports rate statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysSmtFddiMacRateEntry

a3ComSysSmtFddiMacRateEntry 1.3.6.1.4.1.43.29.4.9.5.1
An FDDI MAC rate entry contains rate statistics for a particular FDDI MAC managed by this agent. Rate statistics are calculated based on a one second sampling interval.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysSmtFddiMacRateEntry  

a3ComSysSmtFddiMacRateSmtIndex 1.3.6.1.4.1.43.29.4.9.5.1.1
The index of the SMT instance identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacRateIndex 1.3.6.1.4.1.43.29.4.9.5.1.2
The index of the FDDI MAC identified by this entry, within the SMT identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacRateByteReceiveRate 1.3.6.1.4.1.43.29.4.9.5.1.3
The average number of bytes received per second by the FDDI MAC identified by this entry during the most recent sampling period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacRatePeakByteReceiveRate 1.3.6.1.4.1.43.29.4.9.5.1.4
The peak value of a3ComSysSmtFddiMacByteReceiveRate since the system was last initialized for the FDDI MAC identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacRateFrameReceiveRate 1.3.6.1.4.1.43.29.4.9.5.1.5
The average number of frames received per second by the FDDI MAC identified by this entry during the most recent sampling period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacRatePeakFrameReceiveRate 1.3.6.1.4.1.43.29.4.9.5.1.6
The peak value of a3ComSysSmtFddiMacRateFrameReceiveRate since the system was last initialized for the FDDI MAC identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacRateByteTransmitRate 1.3.6.1.4.1.43.29.4.9.5.1.7
The average number of bytes transmitted per second by the FDDI MAC identified by this entry during the most recent sampling period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacRatePeakByteTransmitRate 1.3.6.1.4.1.43.29.4.9.5.1.8
The peak value of a3ComSysSmtFddiMacByteTransmitRate since the system was last initialized for the FDDI MAC identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacRateFrameTransmitRate 1.3.6.1.4.1.43.29.4.9.5.1.9
The average number of frames transmitted per second by the FDDI MAC identified by this entry during the most recent sampling period.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacRatePeakFrameTransmitRate 1.3.6.1.4.1.43.29.4.9.5.1.10
The peak value of a3ComSysSmtFddiMacFrameTransmitRate since the system was last initialized for the FDDI MAC identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiPortTable 1.3.6.1.4.1.43.29.4.9.6
A list of FDDI port entries. A single entry exists in this list for each FDDI port managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysSmtFddiPortEntry

a3ComSysSmtFddiPortEntry 1.3.6.1.4.1.43.29.4.9.6.1
An FDDI port entry contains information about a particular FDDI port managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysSmtFddiPortEntry  

a3ComSysSmtFddiPortSmtIndex 1.3.6.1.4.1.43.29.4.9.6.1.1
The index of the SMT instance identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiPortIndex 1.3.6.1.4.1.43.29.4.9.6.1.2
The index of the FDDI port identified by this entry, within the SMT identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiPortLocationType 1.3.6.1.4.1.43.29.4.9.6.1.3
The type of location where the FDDI port identified by this entry is physically located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), modularSlot(2), chassis(3), modularCard(4)  

a3ComSysSmtFddiPortLocationTypeIndex 1.3.6.1.4.1.43.29.4.9.6.1.4
The index of the location identified by the corresponding instance of a3ComSysSmtFddiPortLocationType where the FDDI port identified by this entry is physically located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiPortLocationLocalIndex 1.3.6.1.4.1.43.29.4.9.6.1.5
The local index of the FDDI port identified by this entry relative to the location specified by the corresponding values of a3ComSysSmtFddiPortLocationType and a3ComSysSmtFddiPortLocationTypeIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiPortLabel 1.3.6.1.4.1.43.29.4.9.6.1.6
An ASCII text string describing the FDDI port identified by this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

a3ComSysSmtFddiMacLocationTable 1.3.6.1.4.1.43.29.4.9.7
An FDDI MAC Location table contains information to assign an FDDI MAC to a different Location. The system must be rebooted after all changes to this table are completed in order that the changes take effect.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysSmtFddiMacLocationEntry

a3ComSysSmtFddiMacLocationEntry 1.3.6.1.4.1.43.29.4.9.7.1
An FDDI MAC entry contains information to assign an FDDI MAC to a different Location.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysSmtFddiMacLocationEntry  

a3ComSysSmtFddiMacLocationSmtIndex 1.3.6.1.4.1.43.29.4.9.7.1.1
The index of the SMT instance identified by this entry, relative to the agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacLocationIndex 1.3.6.1.4.1.43.29.4.9.7.1.2
The index of the FDDI MAC instance identified by this entry, relative to the SMT identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacCurrentLocation 1.3.6.1.4.1.43.29.4.9.7.1.3
Indicates whether the MAC identified by this entry is assigned to a backplane FDDI station (internal) or an FDDI station configured on a module (external.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER internalBackplane(1), externalFddiPort(2)  

a3ComSysSmtFddiMacRequestedLocation 1.3.6.1.4.1.43.29.4.9.7.1.4
The Location which the MAC identified by this entry is to be assigned to during the next reboot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internalBackplane(1), externalFddiPort(2)  

a3ComSysSmtFddiMacAvailableLocation 1.3.6.1.4.1.43.29.4.9.7.1.5
Indicates the Location(s) available for this MAC. A mac Location which can be modified to either the interanl backplane or an external FDDI port is indicated by internalOrExternal(3).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER internalBackplane(1), externalFddiPort(2), internalOrExternal(3)  

a3ComSysSmtFddiMacStationTable 1.3.6.1.4.1.43.29.4.9.8
An FDDI station MAC table contains information to assign an FDDI MAC to an FDDI Station. The system must be rebooted after all changes to this table are completed in order that the changes take effect.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysSmtFddiMacStationEntry

a3ComSysSmtFddiMacStationEntry 1.3.6.1.4.1.43.29.4.9.8.1
An FDDI MAC entry contains information to assign an FDDI MAC to an FDDI Station.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysSmtFddiMacStationEntry  

a3ComSysSmtFddiMacStationSmtIndex 1.3.6.1.4.1.43.29.4.9.8.1.1
The index of the SMT instance identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacStationIndex 1.3.6.1.4.1.43.29.4.9.8.1.2
The index of the MAC instance identified by this entry, relative to the SMT identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacCurrentStation 1.3.6.1.4.1.43.29.4.9.8.1.3
Indicates which FDDI station that the FDDI MAC identified by this entry is assigned to. A value of 0 indicates that the mac is assigned to an external station. Otherwise the value represents the internal backplane station number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacRequestedStation 1.3.6.1.4.1.43.29.4.9.8.1.4
Indicates which FDDI station the FDDI MAC identified by this entry will be set to during the next system reboot. A value of 0 indicates an external station. Otherwise the value represents the internal backplane station number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiMacAvailableStations 1.3.6.1.4.1.43.29.4.9.8.1.5
This value is a sum. Setting of the first bit (LSB) indicates that the MAC can be assigned to an external station. Available backplane stations are indicated by adding 2^StationNumber to the sum. Where StationNumber represents a backplane station number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiPortStationTable 1.3.6.1.4.1.43.29.4.9.9
An FDDI station Port table contains information to assign an FDDI Port to an FDDI Station. The system must be rebooted after all changes to this table are completed in order that the changes take effect.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysSmtFddiPortStationEntry

a3ComSysSmtFddiPortStationEntry 1.3.6.1.4.1.43.29.4.9.9.1
An FDDI Port entry contains information to assign an FDDI Port to an FDDI Station.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysSmtFddiPortStationEntry  

a3ComSysSmtFddiPortStationSmtIndex 1.3.6.1.4.1.43.29.4.9.9.1.1
The index of the SMT instance identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiPortStationIndex 1.3.6.1.4.1.43.29.4.9.9.1.2
The index of the Port instance identified by this entry, relative to the SMT indentified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiPortCurrentStation 1.3.6.1.4.1.43.29.4.9.9.1.3
Indicates which FDDI station the FDDI Port identified by this entry is assigned to. A value of 0 indicates that the Port is assigned to an external station. Otherwise the value represents the internal backplane station number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiPortRequestedStation 1.3.6.1.4.1.43.29.4.9.9.1.4
Indicates which FDDI station the FDDI port identified by this entry will be set to during the next system reboot. A value of 0 indicates an external station. Otherwise the value represents the internal backplane station number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysSmtFddiPortAvailableStations 1.3.6.1.4.1.43.29.4.9.9.1.5
This value is a sum. Setting of the first bit indicates that the port can be assigned to an external station. Available backplane stations are indicated by adding 2^StationNumber to the sum. Where StationNumber represents a backplane station number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgeCount 1.3.6.1.4.1.43.29.4.10.1
The count of bridges managed by this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgeTable 1.3.6.1.4.1.43.29.4.10.2
A list of bridge entries. A single entry exists in this list for each bridge managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysBridgeEntry

a3ComSysBridgeEntry 1.3.6.1.4.1.43.29.4.10.2.1
A bridge entry contains information about a particular bridge managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysBridgeEntry  

a3ComSysBridgeIndex 1.3.6.1.4.1.43.29.4.10.2.1.1
The index of the bridge identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgePortCount 1.3.6.1.4.1.43.29.4.10.2.1.2
The number of bridge ports that the bridge identified by this entry controls.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgeAddressTableSize 1.3.6.1.4.1.43.29.4.10.2.1.3
The size of the address table for the bridge identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgeAddressTableCount 1.3.6.1.4.1.43.29.4.10.2.1.4
The current count of addresses in the address table for the bridge identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgeAddressTablePeakCount 1.3.6.1.4.1.43.29.4.10.2.1.5
The peak count of addresses in the address table for the bridge identified by this entry, since the system was last initialized.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgeAddressThreshold 1.3.6.1.4.1.43.29.4.10.2.1.6
A reporting threshold for the total number of addresses known for the bridge identified by this entry. When this threshold is reached, the event a3ComSysBridgeAddressThresholdEvent is generated. The range of valid values for setting this object is between 1 and the corresponding value reported by a3ComSysBridgeAddressTableSize + 1 (Note that this range applies to values issued in set requests. The current value may be outside this range, for example if the corresponding value of a3ComSysBridgeMode is changed). Setting this object to one greater than the address table size disables the generation of a3ComSysBridgeAddressThresholdEvents since the limit will never be reached.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgeMode 1.3.6.1.4.1.43.29.4.10.2.1.7
The operational mode of the bridge identified by this entry. Note that bridges which report notSupported(3) will not support sets of this object, and that the value notSupported(3) is not a valid value for a set operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER expressMode(1), ieee8021dBridgeMode(2), notSupported(3), ieee8021dSRTBridgeMode(4), ieee8021dSRBridgeMode(5), ibmSRBridgeMode(6), srtBBridgeMode(7), srExpressBridgeMode(8)  

a3ComSysBridgeBackbonePort 1.3.6.1.4.1.43.29.4.10.2.1.8
The number of the port selected as the backbone segment port when the corresponding value of a3ComSysBridgeMode is is expressMode(1). The value of this object can range from 1 to the corresponding value of a3ComSysBridgePortCount, however, some bridges may support only a subset of ports as backbone ports. If the corresponding value of a3ComSysBridgeMode is not expressMode(1), the value of this object is ignored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgeIpFragmentationEnabled 1.3.6.1.4.1.43.29.4.10.2.1.9
A flag indicating whether or not IP fragmentation is enabled on this bridge. Note that bridges which report notSupported(3) will not support sets of this object, and that the value notSupported(3) is not a valid value for a set operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), notSupported(3)  

a3ComSysBridgeTrFddiTranslationMode 1.3.6.1.4.1.43.29.4.10.2.1.10
The mode used to describe whether the embedded MAC addresses are byte-conjugated in order to convert them from Token Ring format to native FDDI format (and vice versa), or whether they are left alone (used for traffic flowing across a FDDI backbone to/from Token Ring end stations).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER native(1), backbone(2)  

a3ComSysBridgeSTPGroupAddress 1.3.6.1.4.1.43.29.4.10.2.1.11
Spanning tree bridge group address. The address cannot be changed if the spanning tree is enabled (a3ComSysBridgeStpEnabled).
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(6)  

a3ComSysBridgeSTPEnable 1.3.6.1.4.1.43.29.4.10.2.1.12
This object indicates if spanning tree bridge feature is enabled or disabled. If enabled this value will equal true(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

a3ComSysBridgeIpxSnapTranslationEnable 1.3.6.1.4.1.43.29.4.10.2.1.13
This object indicates if the IPX 802.3-FDDI SNAP Translation bridge feature is enabled or disabled. If enabled this value will equal true(1). Note, this object may not be supported on all bridges.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

a3ComSysBridgeLowLatencyEnable 1.3.6.1.4.1.43.29.4.10.2.1.14
This object indicates if the bridge low latency feature is enabled or disabled. If enabled this value will equal true(1). Note, this object may not be supported on all bridges.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

a3ComSysBridgeVlanMode 1.3.6.1.4.1.43.29.4.10.2.1.15
This object indicates the VLAN types that this bridge will support. Open mode means that each VLAN within this bridge will be of the Open type; all VLANs within this bridge will share the same address table. Closed mode means that each VLAN within this bridge will be of the Closed type; each VLAN within this bridge will have its own address table. Mixed mode means that each VLAN within this bridge with be of either the Open or Closed type; all Open VLANs will share the same address table and each Closed VLAN will have its own address table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER open(1), closed(2), mixed(3), notSupported(4)  

a3ComSysBridgePortTable 1.3.6.1.4.1.43.29.4.10.3
A list of bridge port entries. A single entry exists in this list for each bridge port managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysBridgePortEntry

a3ComSysBridgePortEntry 1.3.6.1.4.1.43.29.4.10.3.1
A bridge port entry contains information about a particular bridge port managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysBridgePortEntry  

a3ComSysBridgePortBridgeIndex 1.3.6.1.4.1.43.29.4.10.3.1.1
The index of the bridge identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgePortIndex 1.3.6.1.4.1.43.29.4.10.3.1.2
The index of the bridge port identified by this entry, within the bridge identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgePortIfIndex 1.3.6.1.4.1.43.29.4.10.3.1.3
The value of the MIB-II ifIndex corresponding to the bridge port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgePortReceiveMulticastLimit 1.3.6.1.4.1.43.29.4.10.3.1.4
This variable limits the number of multicast frames forwarded by this port over a 1 second interval. The minimum threshold limit may vary between platforms, but can be determined by multiplying this value by the a3ComSysBridgePortReceiveMulticastLimitMultiplier value. For example if this value equals 2, and the a3ComSysBridgePortReceiveMulticastLimitMultiplier equals 1000 then no more than 2000 multicast frames per second will be forwarded by this port. The default value for this object is zero which an infinite rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

a3ComSysBridgePortAddressAction 1.3.6.1.4.1.43.29.4.10.3.1.5
This object, when read, always returns the value other(1). The behavior of setting this object to each of the acceptable values is as follows: freezeAddress: causes all the learned dynamic addresses to be converted into static addresses. flushAddress: causes all the addresses to be flushed from the address list for the bridge port identified by this entry. flushDynamicAddress: causes all dynamic addresses to be flushed from the address list for the bridge port identified by this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), freezeAddress(2), flushAddress(3), flushDynamicAddress(4)  

a3ComSysBridgePortSpanningTreeFrameReceivedCounts 1.3.6.1.4.1.43.29.4.10.3.1.6
The number of spanning tree frames received by the bridge port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortReceiveBlockedDiscards 1.3.6.1.4.1.43.29.4.10.3.1.7
The number of frames discarded by the bridge port identified by this entry because the receiving bridge port was not in the 'forwarding' state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortReceiveMulticastLimitExceededs 1.3.6.1.4.1.43.29.4.10.3.1.8
The number of times the value of a3ComSysBridgePortReceiveMulticastLimit was exceeded for the port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortReceiveMulticastLimitExceededDiscards 1.3.6.1.4.1.43.29.4.10.3.1.9
The number of multicast/broadcast frames discarded by the bridge port identified by this entry because the corresponding value of a3ComSysBridgePortReceiveMulticastLimit was exceeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortReceiveSecurityDiscards 1.3.6.1.4.1.43.29.4.10.3.1.10
The number of frames discarded by the bridge port identified by this entry because they contained source addresses which were statically configured on another bridge port. A statically configured address (station), which is not allowed to move, appears to have moved.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortReceiveUnknownDiscards 1.3.6.1.4.1.43.29.4.10.3.1.11
The number of frames discarded by the bridge port identified by this entry because the destination address was unknown. Note that this counter is only valid for backbone ports, and only when the bridge is operating in express mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortReceiveOtherDiscards 1.3.6.1.4.1.43.29.4.10.3.1.12
The number of frames discarded by the bridge port identified by this entry because they contained either invalid (group) source addresses or source addresses belonging to this bridge (indicative of network loops).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortReceiveErrorDiscards 1.3.6.1.4.1.43.29.4.10.3.1.13
The number of frames discarded by the bridge port identified by this entry because of internal bridge system errors (e.g., hardware and software address table discrepencies).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortSameSegmentDiscards 1.3.6.1.4.1.43.29.4.10.3.1.14
The number of frames discarded by the bridge port identified by this entry because the destination address is known on the same network segment as the source address, i.e., the frame does not need to be bridged.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortTransmitBlockedDiscards 1.3.6.1.4.1.43.29.4.10.3.1.15
The number of frames discarded by the bridge port identified by this entry because the transmitting bridge port was not in the 'forwarding' state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortReceiveAllPathFilteredFrames 1.3.6.1.4.1.43.29.4.10.3.1.16
The number of frames discarded by the bridge port identified by this entry due to user defined receive all path filters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortReceiveMulticastPathFilteredFrames 1.3.6.1.4.1.43.29.4.10.3.1.17
The number of frames discarded by the bridge port identified by this entry due to user defined receive multicast path filters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortTransmitAllPathFilteredFrames 1.3.6.1.4.1.43.29.4.10.3.1.18
The number of frames discarded by the bridge port identified by this entry due to user defined transmit all path filters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortTransmitMulticastPathFilteredFrames 1.3.6.1.4.1.43.29.4.10.3.1.19
The number of frames discarded by the bridge port identified by this entry due to user defined transmit multicast path filters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortForwardedUnicastFrames 1.3.6.1.4.1.43.29.4.10.3.1.20
The number of unicast frames which this port forwarded to a single destination port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortForwardedUnicastOctets 1.3.6.1.4.1.43.29.4.10.3.1.21
The number of octets contained in unicast frames which this port forwarded to a single destination port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortForwardedMulticastFrames 1.3.6.1.4.1.43.29.4.10.3.1.22
The number of multicast frames which this port forwarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortForwardedMulticastOctets 1.3.6.1.4.1.43.29.4.10.3.1.23
The number of octets contained in multicast frames which this port forwarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortFloodedUnicastFrames 1.3.6.1.4.1.43.29.4.10.3.1.24
The number of unicast frames which this port flooded to all other ports in the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortFloodedUnicastOctets 1.3.6.1.4.1.43.29.4.10.3.1.25
The number of octets contained in unicast frames which this port flooded to all other ports in the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortStpMode 1.3.6.1.4.1.43.29.4.10.3.1.26
The mode of the bridge port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), remove(3)  

a3ComSysBridgePortReceiveMulticastLimitFrameType 1.3.6.1.4.1.43.29.4.10.3.1.27
This object identifies the frames type(s) that are to be counted when determining if the receive multicast limit has been exceeded for this bridge port. Devices attached to networks with predominantly high multicast traffic (e.g. video) should set this value to broadcastOnly(2) to detect broadcast storms.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER broadcastAndMulticast(1), broadcastOnly(2)  

a3ComSysBridgePortForwardedFrames 1.3.6.1.4.1.43.29.4.10.3.1.28
The number of frames which this port forwarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysBridgePortReceiveMulticastLimitMultiplier 1.3.6.1.4.1.43.29.4.10.3.1.29
This variable determines the minimum setting for the multicast limit threshold. For example if this value equals 1000, and the a3ComSysBridgePortReceiveMulticastLimit variable equals 2 then no more than 2000 multicast frames per second will be forwarded by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgePortAddressTable 1.3.6.1.4.1.43.29.4.10.5
A list of bridge port address information. A single entry exists in this list for each learned address, accross all bridge ports and all bridges managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysBridgePortAddressEntry

a3ComSysBridgePortAddressEntry 1.3.6.1.4.1.43.29.4.10.5.1
An bridge port address entry contains information about a particular bridge port address. To create a new entry, set an instance of a3ComSysBridgePortAddressRemoteAddress with the address index portion of the instance set to 0, to a valid value. To remove an entry, set the instance of the a3ComSysBridgePortAddressType for the entry to invalid(2).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysBridgePortAddressEntry  

a3ComSysBridgePortAddressBridgeIndex 1.3.6.1.4.1.43.29.4.10.5.1.1
The index of the bridge identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgePortAddressPortIndex 1.3.6.1.4.1.43.29.4.10.5.1.2
The index of the bridge port identified by this entry, within the bridge identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgePortAddressIndex 1.3.6.1.4.1.43.29.4.10.5.1.3
The index of this address entry within the bridge address table for the bridge identified by this entry. This index ranges from 1 to the corresponding value of a3ComSysBridgeAddressTableSize.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgePortAddressRemoteAddress 1.3.6.1.4.1.43.29.4.10.5.1.4
The remote MAC address detected on the bridge port identified by to this entry. Setting this object results in an attempt to create a new entry in the table. Since the value of a3ComSysBridgePortAddressIndex is determined automatically internal to the bridge, a set is only successful if the index value specified for a3ComSysBridgePortAddressIndex is zero. A get-next using the values of a3ComSysBridgePortAddressTypeIndex and a3ComSysBridgePortAddressPortIndex can be used to determine the address index assigned to the newly added address entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(6)  

a3ComSysBridgePortAddressType 1.3.6.1.4.1.43.29.4.10.5.1.5
This object, when read, always returns the value valid(1). Setting this object to invalid(2) will remove the corresponding address entry from the table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

a3ComSysBridgePortAddressIsStatic 1.3.6.1.4.1.43.29.4.10.5.1.6
A value indicating whether this MAC address was statically configured or was dynamically learned. Note that isStatic(1) it the only valid for set operations.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER isStatic(1), isDynamic(2)  

a3ComSysBridgePortAddressStaticPort 1.3.6.1.4.1.43.29.4.10.5.1.7
If the corresponding value of the object a3ComSysBridgePortAddressIsStatic is isStatic(1), this object indicates the local bridge port index (as reported by a3ComSysBridgePortLocalIndex) for which this address MAC was statically configured. If the object a3ComSysBridgePortAddressIsStatic has the value isDynamic(2), the value of this object is 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgePortAddressAge 1.3.6.1.4.1.43.29.4.10.5.1.8
This object indicates the time, in seconds, elapsed since a packet containing this address as a source was last seen on the bridge port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysBridgeStpGroupAddress 1.3.6.1.4.1.43.29.4.10.6
Spanning tree bridge group address. The address cannot be changed if the spanning tree is enabled (a3ComSysBridgeStpEnabled). This object can now be found under the a3ComSysBridgeTable as a3ComSysBridgeSTPGroupAddress.
Status: obsolete Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(6)  

a3ComSysBridgeStpEnable 1.3.6.1.4.1.43.29.4.10.7
This object indicates if spanning tree bridge feature is enabled or disabled. If enabled this value will equal true(1). This object can now be found under the a3ComSysBridgeTable as a3ComSysBridgeSTPEnable.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

a3ComSysNetworkAnalyzerTable 1.3.6.1.4.1.43.29.4.12.1
A list of analyzer entries. A single entry exists in this list for each bridge port configured for an analyzer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysNetworkAnalyzerTableEntry

a3ComSysNetworkAnalyzerTableEntry 1.3.6.1.4.1.43.29.4.12.1.1
An analyzer table entry contains information relating an analyzer port address to the bridge and port index for that analyzer. The effect of creating an entry for a particular port is to configure that port for monitoring. A port which is configured for monitoring is no longer available for switching. To create an entry, set the value of the a3ComSysNetworkAnalyzerStatus object for a non-existent instance to valid(1). The value of the a3ComSysNetworkAnalyzerPhysicalAddress object for the new entry is filled in as a result of the creation. The effect of removing an entry for a particular port is to disable the port for monitoring. The port is then available for switching. To remove an entry, set the value of the corresponding instance of the a3ComSysNetworkAnalyzerStatus object to invalid(2).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysNetworkAnalyzerTableEntry  

a3ComSysNetworkAnalyzerBridgeIndex 1.3.6.1.4.1.43.29.4.12.1.1.1
The index of the bridge relative to this agent where the analyzer identified by this entry is configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysNetworkAnalyzerBridgePortIndex 1.3.6.1.4.1.43.29.4.12.1.1.2
The index of the port relative to the bridge identified by this entry where the analyzer identified by this entry is configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysNetworkAnalyzerPhysicalAddress 1.3.6.1.4.1.43.29.4.12.1.1.3
The physical address of the bridge port identified by the corresponding values of a3ComSysNetworkAnalyzerBridgeIndex and a3ComSysNetworkAnayzerBridgePortIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

a3ComSysNetworkAnalyzerStatus 1.3.6.1.4.1.43.29.4.12.1.1.4
The status of the entry. Setting the value of a non-existent instance of this object to valid(1) attempts to add the corresponding entry to the table. The effect of adding an entry to the table is to configure the port for monitoring and to disable it for switching. Setting an existing instance of this object to invalid(2) attempts to remove the corresponding entry from the table. The effect of removing an entry from the table is to disable the port for monitoring and to make available for switching.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

a3ComSysNetworkPortMonitorTable 1.3.6.1.4.1.43.29.4.12.2
A list of monitor port entries. A single entry exists in this for each bridge port being monitored.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysNetworkPortMonitorTableEntry

a3ComSysNetworkPortMonitorTableEntry 1.3.6.1.4.1.43.29.4.12.2.1
A port monitor table entry contains information relating a bridge port being monitored with the address of the analyzer which is being used to monitor the port. The effect of creating an entry for a particular port is to enable monitoring of that port by the analyzer specified. To create an entry, set the value of the a3ComSysNetworkPortMonitorAnalyzerAddress object to the address of the network analyzer port. This value should be the same as the value of the a3ComSysNetworkAnalyzerPhysicalAddress object for the analyzer. The effect of removing an entry for a particular port is to disable monitoring of that port. To remove an entry, set the value of the corresponding instance of the a3ComSysNetworkPortMonitorStatus object to invalid(2).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysNetworkPortMonitorTableEntry  

a3ComSysNetworkPortMonitorBridgeIndex 1.3.6.1.4.1.43.29.4.12.2.1.1
The index of the bridge relative to this agent where the monitored port identified by this entry is located.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysNetworkPortMonitorBridgePortIndex 1.3.6.1.4.1.43.29.4.12.2.1.2
The index of the port which is being monitored relative to the bridge identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysNetworkPortMonitorAnalyzerAddress 1.3.6.1.4.1.43.29.4.12.2.1.3
The physical address of the port where the analyzer, which is monitoring the port identified by this entry, is located. Setting the value of a non-existent instance of this object attempts to add an entry to the table. The effect of adding an entry to the table is to enable monitoring of the port by the analyzer specified. Setting the value of an existing instance of this object will switch the monitored port to the new analyzer address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(6)  

a3ComSysNetworkPortMonitorStatus 1.3.6.1.4.1.43.29.4.12.2.1.4
The status of the entry. Setting an existing instance of this object to invalid(2) attempts to remove the corresponding entry from the table. The effect of removing an entry from the table is to disable monitoring of the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

a3ComSysTokenRingPortCount 1.3.6.1.4.1.43.29.4.13.1
The count of token ring ports managed by this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysTokenRingPortTable 1.3.6.1.4.1.43.29.4.13.2
A list of token ring port entries. A single entry exists in this list for each token ring port managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysTokenRingPortEntry

a3ComSysTokenRingPortEntry 1.3.6.1.4.1.43.29.4.13.2.1
A token ring port entry contains information about a particular token ring port managed by this agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysTokenRingPortEntry  

a3ComSysTokenRingPortIndex 1.3.6.1.4.1.43.29.4.13.2.1.1
The index of the token ring port identified by this entry, relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysTokenRingPortIfIndex 1.3.6.1.4.1.43.29.4.13.2.1.2
The value of the MIB-II ifIndex corresponding to the token ring port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysTokenRingPortLabel 1.3.6.1.4.1.43.29.4.13.2.1.3
An ASCII text string describing the token ring port identified by this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

a3ComSysTokenRingPortInsertStatus 1.3.6.1.4.1.43.29.4.13.2.1.4
The current value of the link status for the token ring port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inserted(1), deinserted(2)  

a3ComSysTokenRingPortType 1.3.6.1.4.1.43.29.4.13.2.1.5
Specific port type description for the token ring port identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER rj45(1), other(2)  

a3ComSysTokenRingPortMode 1.3.6.1.4.1.43.29.4.13.2.1.6
The current mode of the port. The default mode (station) is used to connect a hub to the port. Lobe mode is used to direct connect a Token Ring station into the port. This selection can only be made on ports 1 and 2 of the module.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER station(1), lobe(2)  

a3ComSysTokenRingPortSpeed 1.3.6.1.4.1.43.29.4.13.2.1.7
The current speed of the port. The default speed is sixteenMegabit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER fourMegabit(1), sixteenMegabit(2), sixteenMegabitETR(3)  

a3ComSysTokenRingPortLineErrors 1.3.6.1.4.1.43.29.4.13.2.1.8
This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between the SD and the ED of the frame or token, or 2) there is an FCS error in the frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortBurstErrors 1.3.6.1.4.1.43.29.4.13.2.1.9
This counter is incremented when a station detects the absence of transitions for five half-bit timers (burst-five error).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortACErrors 1.3.6.1.4.1.43.29.4.13.2.1.10
This counter is incremented when a station receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is equal to C is equal to 0 without first receiving an AMP frame. It denotes a station that cannot set the AC bits properly.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortAbortTransErrors 1.3.6.1.4.1.43.29.4.13.2.1.11
This counter is incremented when a station transmits an abort delimiter while transmitting.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortInternalErrors 1.3.6.1.4.1.43.29.4.13.2.1.12
This counter is incremented when a station recognizes an internal error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortLostFrameErrors 1.3.6.1.4.1.43.29.4.13.2.1.13
This counter is incremented when a station is transmitting and its TRR timer expires. This condition denotes a condition where a transmitting station in strip mode does not receive the trailer of the frame before the TRR timer goes off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortReceiveCongestionErrors 1.3.6.1.4.1.43.29.4.13.2.1.14
This counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer space indicating that the station is congested.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortFrameCopiedErrors 1.3.6.1.4.1.43.29.4.13.2.1.15
This counter is incremented when a station recognizes a frame addressed to its specific address and detects that the FS field A bits are set to 1 indicating a possible line hit or duplicate address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortTokenErrors 1.3.6.1.4.1.43.29.4.13.2.1.16
This counter is incremented when a station acting as the active monitor recognizes an error condition that needs a token transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortSoftErrors 1.3.6.1.4.1.43.29.4.13.2.1.17
The number of Soft Errors the interface has detected. It directly corresponds to the number of Report Error MAC frames that this interface has transmitted. Soft Errors are those which are recoverable by the MAC layer protocols.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortHardErrors 1.3.6.1.4.1.43.29.4.13.2.1.18
The number of times this interface has detected an immediately recoverable fatal error. It denotes the number of times this interface is either transmitting or receiving beacon MAC frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortTransmitBeacons 1.3.6.1.4.1.43.29.4.13.2.1.19
The number of times this interface has transmitted a beacon frame.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortLobeWires 1.3.6.1.4.1.43.29.4.13.2.1.20
The number of times the interface has detected an open or short circuit in the lobe data path. The adapter will be closed when this condition occurs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortRemoves 1.3.6.1.4.1.43.29.4.13.2.1.21
The number of times the interface has received a Remove Ring Station MAC frame request. When this frame is received the interface will enter the close state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortSingles 1.3.6.1.4.1.43.29.4.13.2.1.22
The number of times the interface has sensed that it is the only station on the ring. This will happen if the interface is the first one up on a ring, or if there is a hardware problem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortFreqErrors 1.3.6.1.4.1.43.29.4.13.2.1.23
The number of times the interface has detected that the frequency of the incoming signal differs from the expected frequency.
Status: optional Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysTokenRingPortRingStatus 1.3.6.1.4.1.43.29.4.13.2.1.24
The current interface status which can be used to diagnose fluctuating problems that can occur on token rings, after a station has successfully been added to the ring. Before an open is completed, this object has the value for the 'no status' condition. This object is useful for debugging problems when the station can not even enter the ring. The object's value is a sum of values, one for each currently applicable condition. The following values are defined for various conditions: 0 = No Problems detected 32 = Ring Recovery 64 = Single Station 256 = Remove Received 512 = reserved 1024 = Auto-Removal Error 2048 = Lobe Wire Fault 4096 = Transmit Beacon 8192 = Soft Error 16384 = Hard Error 32768 = Signal Loss 131072 = no status, open not completed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysFtTable 1.3.6.1.4.1.43.29.4.14.1
A list of entries which describe file transfers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysFtTableEntry

a3ComSysFtTableEntry 1.3.6.1.4.1.43.29.4.14.1.1
A description of a particular file transfer entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysFtTableEntry  

a3ComSysFtIndex 1.3.6.1.4.1.43.29.4.14.1.1.1
A unique index used to identifying this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

a3ComSysFtDirection 1.3.6.1.4.1.43.29.4.14.1.1.2
Specifies the direction of the file transfer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER localToRemote(1), remoteToLocal(2)  

a3ComSysFtLocalStorageType 1.3.6.1.4.1.43.29.4.14.1.1.3
The type of storage on the local system to be used as the source/destination for the file transfer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  A3ComSysStorageType  

a3ComSysFtLocalResourceType 1.3.6.1.4.1.43.29.4.14.1.1.4
The type of resource on the local system to be used as the source/destination for the file transfer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  A3ComSysResourceType  

a3ComSysFtLocalResourceMask 1.3.6.1.4.1.43.29.4.14.1.1.5
The indices of the resources on the local system to be used as the source/destination for the file transfer. The type of resource to which these indices apply is specified by the corresponding value of a3ComSysFtLocalResourceType. If resourceBridge is used, a3ComSysFtLocalResourceMask indicates the bridge slot number the filter code will be downloaded. For instance, a3ComSysFtLocalResourceMask value of 0x03 indicates bridge slot number 1 and 2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  A3ComSysResourceBitMask  

a3ComSysFtLocalResourceAttribute 1.3.6.1.4.1.43.29.4.14.1.1.6
An identifier which specifies the particular resource attribute on the local system which is the source/destination of the file transfer. The resource(s) to which this attribute applies is specified by the corresponding values of a3ComSysFtLocalResourceType and a3ComSysFtLocalResourceMask.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OBJECT IDENTIFIER  

a3ComSysFtRemoteAddressType 1.3.6.1.4.1.43.29.4.14.1.1.7
The type of address which is specified by the corresponding value of a3ComSysFtRemoteAddress.
Status: mandatory Access: read-write
OBJECT-TYPE    
  A3ComSysAddressType  

a3ComSysFtRemoteAddress 1.3.6.1.4.1.43.29.4.14.1.1.8
The address of the source/destination file on the remote system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

a3ComSysFtRemoteFileName 1.3.6.1.4.1.43.29.4.14.1.1.9
The full path name of the source/destination file on the remote system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

a3ComSysFtRemoteUserName 1.3.6.1.4.1.43.29.4.14.1.1.10
The user name to be used when requesting the file transfer to/from the remote system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

a3ComSysFtRemoteUserPassword 1.3.6.1.4.1.43.29.4.14.1.1.11
The password to be used when requesting the file transfer to/from the remote system. When read, this object returns a zero length string. Note that, for security reasons, some ftp servers may insist on a non-zero length user password.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

a3ComSysFtForceTransfer 1.3.6.1.4.1.43.29.4.14.1.1.12
Setting this object to true makes the agent ignore non-fatal (i.e. version/id mismatch) errors encountered during a file transfer request.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

a3ComSysFtBytesTransferred 1.3.6.1.4.1.43.29.4.14.1.1.13
The number of bytes successfully transferred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

a3ComSysFtStatus 1.3.6.1.4.1.43.29.4.14.1.1.14
The status of the file transfer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER statusSuccessfulCompletion(1), statusInProgress(2), statusLocalInvalid(3), statusRemoteInvalid(4), statusRemoteUnreachable(5), statusUserAuthFailed(6), statusFileNotFound(7), statusFileTooBig(8), statusFileIncompatible(9), statusError(10)  

a3ComSysFtDetailedStatus 1.3.6.1.4.1.43.29.4.14.1.1.15
Detailed status for the transfer for the particular local resource attribute specified by the corresponding values of a3ComSysFtLocalStorageType, a3ComSysFtLocalResourceType, a3ComSysFtLocalResourceMask, and a3ComSysFtLocalResourceAttribute. Note that this object is only valid in the case where a3ComSysFtStatus indicates an error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

a3ComSysFtDetailedStatusString 1.3.6.1.4.1.43.29.4.14.1.1.16
Detailed status description for the requested transfer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysFtOwnerString 1.3.6.1.4.1.43.29.4.14.1.1.17
A string describing the creator/owner of this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

a3ComSysFtRowStatus 1.3.6.1.4.1.43.29.4.14.1.1.18
The row status object controls the creation/deletion of rows in this table. Its semantics are the same as those for the RowStatus textual convention specified for SNMPv2. Setting this object to createAndGo(4) is not allowed. Setting this object to createAndWait(5) causes an entry to be created with a3ComSysFtRowStatus value of notReady(3). Setting this object to active(1) causes the transfer to start for the given row. Objects within the row cannot be modified once a row has been set to active(1), Setting this object to destroy(6) causes the corresponding row to be deleted. Note that a request to set a row to notInService(2) or destroy(6) will fail if the current rowStatus value is active(1) (i.e. a file transfer is currently in progress). This is necessary since aborting a file transfer may leave the system in an inconsistent state. Note that, currently, only a single instance of a row can be created in this table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

a3ComSysFtResourceAttributes 1.3.6.1.4.1.43.29.4.14.2
OBJECT IDENTIFIER    

a3ComSysFtSystemAttributes 1.3.6.1.4.1.43.29.4.14.2.1
OBJECT IDENTIFIER    

a3ComSysFtSystemOperationalCode 1.3.6.1.4.1.43.29.4.14.2.1.1
OBJECT IDENTIFIER    

a3ComSysFtSystemConfiguration 1.3.6.1.4.1.43.29.4.14.2.1.2
OBJECT IDENTIFIER    

a3ComSysFtSystemBridgeFilterCode 1.3.6.1.4.1.43.29.4.14.2.1.3
OBJECT IDENTIFIER    

a3ComSysFtDetailedResourceStatus 1.3.6.1.4.1.43.29.4.14.3
OBJECT IDENTIFIER    

a3ComSysFtSystemDetailedStatus 1.3.6.1.4.1.43.29.4.14.3.1
OBJECT IDENTIFIER    

a3ComSysFtSysStatusNotApplicable 1.3.6.1.4.1.43.29.4.14.3.1.1
OBJECT IDENTIFIER    

a3ComSysFtSysStatusNoImageLabel 1.3.6.1.4.1.43.29.4.14.3.1.2
OBJECT IDENTIFIER    

a3ComSysFtSysStatusConfigIdMismatch 1.3.6.1.4.1.43.29.4.14.3.1.3
OBJECT IDENTIFIER    

a3ComSysFtSysStatusChecksumError 1.3.6.1.4.1.43.29.4.14.3.1.4
OBJECT IDENTIFIER    

a3ComSysFtSysStatusNvRamError 1.3.6.1.4.1.43.29.4.14.3.1.5
OBJECT IDENTIFIER    

a3ComSysFtSysStatusFlashError 1.3.6.1.4.1.43.29.4.14.3.1.6
OBJECT IDENTIFIER    

a3ComSysFtSysStatusNoRoom 1.3.6.1.4.1.43.29.4.14.3.1.7
OBJECT IDENTIFIER    

a3ComSysFtSysBridgeFilterNotApplicable 1.3.6.1.4.1.43.29.4.14.3.1.8
OBJECT IDENTIFIER    

a3ComSysFtSysBridgeFilterSyntaxError 1.3.6.1.4.1.43.29.4.14.3.1.9
OBJECT IDENTIFIER    

a3ComSysFtSysBridgeFilterdownloadError 1.3.6.1.4.1.43.29.4.14.3.1.10
OBJECT IDENTIFIER    

a3ComSysFtSysBridgeFilterNoRoom 1.3.6.1.4.1.43.29.4.14.3.1.11
OBJECT IDENTIFIER    

a3ComSysIpBaseGroup 1.3.6.1.4.1.43.29.4.15.1
OBJECT IDENTIFIER    

a3ComSysIpInterfaceGroup 1.3.6.1.4.1.43.29.4.15.2
OBJECT IDENTIFIER    

a3ComSysIpInterfaceCount 1.3.6.1.4.1.43.29.4.15.2.1
A count of the total number of IP interfaces configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysIpInterfaceTable 1.3.6.1.4.1.43.29.4.15.2.2
A list of configured IP interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysIpInterfaceEntry

a3ComSysIpInterfaceEntry 1.3.6.1.4.1.43.29.4.15.2.2.1
An individual IP interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysIpInterfaceEntry  

a3ComSysIpInterfaceIpStackIndex 1.3.6.1.4.1.43.29.4.15.2.2.1.1
The index of the IP stack identified by this entry relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysIpInterfaceAddr 1.3.6.1.4.1.43.29.4.15.2.2.1.2
The IP address of this entry within the IP stack identified within this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

a3ComSysIpInterfaceNetMask 1.3.6.1.4.1.43.29.4.15.2.2.1.3
The subnet mask associated with this IP interface. The value of the mask is an IP address with all the network bits set to 1 and all the host bits set to 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

a3ComSysIpInterfaceIndex 1.3.6.1.4.1.43.29.4.15.2.2.1.4
The index value which uniquely identifies the interface to which this entry is applicable. lspIPInterfaceIndex maps to the same interface as identified by ifIndex in the ifTable. Currently, this object can not be modified after creation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysIpInterfaceBcastAddr 1.3.6.1.4.1.43.29.4.15.2.2.1.5
This object represents the value of the least significant bit of this entry's direct broadcast address. For example, a value of one signifies that the host portion of the broadcast address is set to all ones.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysIpInterfaceCost 1.3.6.1.4.1.43.29.4.15.2.2.1.6
The route cost metric used for this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

a3ComSysIpInterfaceStatus 1.3.6.1.4.1.43.29.4.15.2.2.1.7
The status column for this IP interface. This object can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the object in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available the agent will reject the request. Other objects in this row entry can be individually modified while the row status is active(1). Setting this object to destroy(6) will remove this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

a3ComSysIpxBaseGroup 1.3.6.1.4.1.43.29.4.16.1
OBJECT IDENTIFIER    

a3ComSysIpxInterfaceGroup 1.3.6.1.4.1.43.29.4.16.2
OBJECT IDENTIFIER    

a3ComSysIpxInterfaceCount 1.3.6.1.4.1.43.29.4.16.2.1
A count of the total number of IPX interfaces configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysIpxInterfaceTable 1.3.6.1.4.1.43.29.4.16.2.2
A list of configured IPX interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysIpxInterfaceEntry

a3ComSysIpxInterfaceEntry 1.3.6.1.4.1.43.29.4.16.2.2.1
An individual IPX interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysIpxInterfaceEntry  

a3ComSysIpxInterfaceIpxStackIndex 1.3.6.1.4.1.43.29.4.16.2.2.1.1
The index of the IPX stack identified by this entry relative to this agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysIpxInterfaceNetNumber 1.3.6.1.4.1.43.29.4.16.2.2.1.2
The IPX Network Number of this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpxNetworkNumber  

a3ComSysIpxInterfaceIfIndex 1.3.6.1.4.1.43.29.4.16.2.2.1.3
The ifIndex of the virtual interface that this IPX interface is is configured over. The a3ComSysIpxInterfaceIfIndex identifies a virtual interface, for example a VLAN, that this local address is associated with for purposes of routing or network management.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysIpxInterfaceCost 1.3.6.1.4.1.43.29.4.16.2.2.1.4
The cost associated with the IPX address of this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysIpxInterfaceFrameType 1.3.6.1.4.1.43.29.4.16.2.2.1.5
The frame format used for routing frames on this IPX interface. The framing formats are for ethernet ports. There are two frame formats for FDDI ports: 802.2 and FDDI SNAP. The correct FDDI format is automatically chosen if this interface is associated with a VLAN interface that contains both ethernet and FDDI ports. If the VLAN interface is an FDDI port, than the only values that can be written to this object are: frame-802-2(2) and frame-SNAP(4).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER frame-ethernetII(1), frame-802-2(2), frame-802-3-Raw(3), frame-SNAP(4)  

a3ComSysIpxInterfaceStatus 1.3.6.1.4.1.43.29.4.16.2.2.1.6
The status column for this IPX interface. This OBJECT can be set to: createAndGo(4) destroy(6) The following value may be read: active(1) Setting this object ot createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the object in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available the agent will reject the request. Other objects in this row entry can be individually modified while the row status is active(1). Setting this object to destroy(6) will remove this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

a3ComSysAppleTalkBaseGroup 1.3.6.1.4.1.43.29.4.17.1
OBJECT IDENTIFIER    

a3ComSysAppleTalkInterfaceGroup 1.3.6.1.4.1.43.29.4.17.2
OBJECT IDENTIFIER    

a3ComSysAtInterfaceCount 1.3.6.1.4.1.43.29.4.17.2.1
A count of the total number of AppleTalk interfaces configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysAtInterfaceTable 1.3.6.1.4.1.43.29.4.17.2.2
A list of AppleTalk ports for this entity.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysAtInterfaceEntry

a3ComSysAtInterfaceEntry 1.3.6.1.4.1.43.29.4.17.2.2.1
An individual appletalk interface entry. Appletalk entries with row status of active(1) cannot be modified but must set to destroy(6) and recreated.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysAtInterfaceEntry  

a3ComSysAtInterfaceAtStackIndex 1.3.6.1.4.1.43.29.4.17.2.2.1.1
The index of the Appletalk stack identified by this entry relative to this agent. Setting of this object is required for all interface creations.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysAtInterfaceNetAddress 1.3.6.1.4.1.43.29.4.17.2.2.1.2
The AppleTalk network address configured for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DdpNodeAddress  

a3ComSysAtInterfaceType 1.3.6.1.4.1.43.29.4.17.2.2.1.3
The type of interface that is configured for this port. Setting of this object is required for all interface creations.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER seedInterface(1), nonseedInterface(2)  

a3ComSysAtInterfaceNetStart 1.3.6.1.4.1.43.29.4.17.2.2.1.4
The first AppleTalk network address in the range configured for this port. If this port is not a native AppleTalk port, this object shall have the value of two octets of zero. Setting of this object is mandatory only for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATNetworkNumber  

a3ComSysAtInterfaceNetEnd 1.3.6.1.4.1.43.29.4.17.2.2.1.5
The last AppleTalk network address in the range configured for this port. If the network to which this AppleTalk port is connected is a non-extended network, or if it is not a native AppleTalk port, the value for a3ComSysAtInterfaceNetEnd shall be two octets of zero. Setting of this object is mandatory only for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATNetworkNumber  

a3ComSysAtInterfaceZoneDefault 1.3.6.1.4.1.43.29.4.17.2.2.1.6
The name of the default zone for this port. If this port only has one zone, that zone is represented here. Setting of this object is mandatory for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone1 1.3.6.1.4.1.43.29.4.17.2.2.1.7
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone2 1.3.6.1.4.1.43.29.4.17.2.2.1.8
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone3 1.3.6.1.4.1.43.29.4.17.2.2.1.9
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone4 1.3.6.1.4.1.43.29.4.17.2.2.1.10
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone5 1.3.6.1.4.1.43.29.4.17.2.2.1.11
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone6 1.3.6.1.4.1.43.29.4.17.2.2.1.12
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone7 1.3.6.1.4.1.43.29.4.17.2.2.1.13
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone8 1.3.6.1.4.1.43.29.4.17.2.2.1.14
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone9 1.3.6.1.4.1.43.29.4.17.2.2.1.15
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone10 1.3.6.1.4.1.43.29.4.17.2.2.1.16
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone11 1.3.6.1.4.1.43.29.4.17.2.2.1.17
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone12 1.3.6.1.4.1.43.29.4.17.2.2.1.18
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone13 1.3.6.1.4.1.43.29.4.17.2.2.1.19
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone14 1.3.6.1.4.1.43.29.4.17.2.2.1.20
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceZone15 1.3.6.1.4.1.43.29.4.17.2.2.1.21
Zone name in this entry's zone list. This object may only only be set for interfaces with a3ComSysAtInterfaceType equal to seedInterface(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  ATName  

a3ComSysAtInterfaceIfIndex 1.3.6.1.4.1.43.29.4.17.2.2.1.22
The interface associated with this AppleTalk port. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the ifTable. Setting of this object is required for all interface creations.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

a3ComSysAtInterfaceState 1.3.6.1.4.1.43.29.4.17.2.2.1.23
The current state of the appletalk interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unused(1), initialize(2), terminate(3), failed(4), down(5), validate(6), discover(7), waiting(8), enabled(9)  

a3ComSysAtInterfaceStatus 1.3.6.1.4.1.43.29.4.17.2.2.1.24
The status column for this IP interface. This object can be set to: createAndGo(4) createAndWait(5) destroy(6) The following value may be read: active(1) notInService(2) Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the object in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available the agent will reject the request. Setting this object to createAndWait(5) causes the agent to create an entry which has the value notInService(2). Only three notInService(2) entries are permitted at any one time. Setting a row with status notInService(2) to active(1) will cause this entry to change to active(1) if the appropriate columns have been set. Setting this object to destroy(6) will remove this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

a3ComSysModuleCardCount 1.3.6.1.4.1.43.29.4.18.1
The current count of module components present in the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysModuleCardInfoTable 1.3.6.1.4.1.43.29.4.18.2
A list of module card information entries. A single entry exists in this list for each modular component in the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysModuleCardInfoEntry

a3ComSysModuleCardInfoEntry 1.3.6.1.4.1.43.29.4.18.2.1
A module card info entry contains information about a particular modular component within the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysModuleCardInfoEntry  

a3ComSysModuleCardInfoIndex 1.3.6.1.4.1.43.29.4.18.2.1.1
The index of the modular component identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysModuleCardInfoFamily 1.3.6.1.4.1.43.29.4.18.2.1.2
The family code for this module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER coreBuilder3500(1), superStack7000(2), superStack9000(3), coreBuilder9000-RF12R(17), coreBuilder9000-RF6MC(18), coreBuilder9000-LF20R(19), coreBuilder9000-LF10MC(20), coreBuilder9000-LF36T(21), coreBuilder9000-FG24(22), coreBuilder9000-FG9(23), coreBuilder9000-LG9MC(24), coreBuilder9000-LG9(25)  

a3ComSysModuleCardInfoGenericType 1.3.6.1.4.1.43.29.4.18.2.1.3
The generic type code for this module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER backplaneOrMotherboard(1), processorBoard(2), enet10MbAnd100MbAdaptor(3), enet1GbAdaptor(4), fddiAdaptor(5), atmAdaptor(6)  

a3ComSysModuleCardInfoSpecificType 1.3.6.1.4.1.43.29.4.18.2.1.4
The specific type code for this module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notApplicable(1), atmSonetOC3Fiber(161), atmSonetOC12Fiber(162), atmSonetOC3Copper(163), atmSonetOC12Copper(164), enet1Gb850nMMultimodeFiber(177), enet1Gb1300nMFiber(178), enet1GbCoax(179), packetSwitchingFabric1000BaseBackplane(180), enet1Gb1000BaseTx(181), enet1000BaseSxMmfSCandGBIC(183), enet100Mb100BaseTx(225), enet10or100BaseTxTelco(226), enet100Mb100BaseFx(227), enet100Mb100BaseT4(228), enet100Mb100BaseTxSTP(229), enet100Mb100BaseT2(230), fddiMultimodeSC(241), fddiSingleModeSC(242), fddiCopperUTP(243), fddiCopperSTP(244)  

a3ComSysModuleCardInfoPartNumber 1.3.6.1.4.1.43.29.4.18.2.1.5
The specific part number for this module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysModuleCardInfoManufacturingDate 1.3.6.1.4.1.43.29.4.18.2.1.6
The date that this module was manufactured in the format mm/dd/yyyy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysModuleCardInfoModuleSerialNumber 1.3.6.1.4.1.43.29.4.18.2.1.7
3Com serial number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

a3ComSysModuleCardInfoTLASerialNumber 1.3.6.1.4.1.43.29.4.18.2.1.8
TOP level assembly serial number for boards with non-removable daughter cards. Null string for all other board types.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(12)  

a3ComSysModuleCardInfo3CNumber 1.3.6.1.4.1.43.29.4.18.2.1.9
On a backplane or non-removable module this is the 3C number of the chassis. On a removable module this is the 3C number of the module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(10)  

a3ComSysModuleCardInfoICTTestStatus 1.3.6.1.4.1.43.29.4.18.2.1.10
1 equals test passed, or greater than 1 identifies the test number failure (0 or FF indicates field yet not written).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysModuleCardInfoICTTestRevision 1.3.6.1.4.1.43.29.4.18.2.1.11
Manufacturing ATE test revision number (XX.XX).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysModuleCardInfoSystemTestStatus 1.3.6.1.4.1.43.29.4.18.2.1.12
1 equals test passed, or greater than 1 identifies the test number failure (0 or FF indicates field yet not written).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysModuleCardInfoFunctionalTestStatus 1.3.6.1.4.1.43.29.4.18.2.1.13
1 equals test passed, or greater than 1 identifies the test number failure (0 or FF indicates field yet not written).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysModuleCardInfoFunctionalTestRevision 1.3.6.1.4.1.43.29.4.18.2.1.14
Manufacturing functional test revision number (XX.XX).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysModuleCardInfoBoardRevision 1.3.6.1.4.1.43.29.4.18.2.1.15
Board revision code.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysModuleCardInfoRuntimeHours 1.3.6.1.4.1.43.29.4.18.2.1.16
A total count of the number of hours this module has been in operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysDiagnosticsInfoTable 1.3.6.1.4.1.43.29.4.19.1
A list of module card information entries. A single entry exists in this list for each modular component in the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    A3ComSysDiagnosticsInfoEntry

a3ComSysDiagnosticsInfoEntry 1.3.6.1.4.1.43.29.4.19.1.1
A diagnostics info entry contains information about a particular diagnostics event on a modular component within the system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  A3ComSysDiagnosticsInfoEntry  

a3ComSysDiagnosticsInfoIndex 1.3.6.1.4.1.43.29.4.19.1.1.1
The index of the diagnostics modular component identified by this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysDiagnosticsInfoPOVDiagnosticsRevision 1.3.6.1.4.1.43.29.4.19.1.1.2
The revision of the POV (power on verification) diagnostics software at the most recent failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysDiagnosticsInfoExtendedDiagnosticsRevision 1.3.6.1.4.1.43.29.4.19.1.1.3
The revision of the extended diagnostics software at the most recent failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysDiagnosticsInfoDiagnosticFailureCode 1.3.6.1.4.1.43.29.4.19.1.1.4
The code written by the diagnostics at the most recent failure. This identifies both the test number and failure code in the following format: -. If there is no failure then 000-000 is displayed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysDiagnosticsInfoDiagnosticFailureDateTime 1.3.6.1.4.1.43.29.4.19.1.1.5
The date and time of the most recent diagnostic failure for the module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

a3ComSysDiagnosticsInfoDiagnosticFailureSlotNumber 1.3.6.1.4.1.43.29.4.19.1.1.6
The slot number (network adapter cards only) of the most recent diagnostic failure for the module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysDiagnosticsInfoDiagnosticFailureCounter 1.3.6.1.4.1.43.29.4.19.1.1.7
The total number of diagnostic failures logged against this module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysDiagnosticsInfoDiagnosticFieldDOACounter 1.3.6.1.4.1.43.29.4.19.1.1.8
The total number of failures occurring at this module during the first 48 hours of operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

a3ComSysSystemOverTemperatureEvent 1
The trap that is generated when the system temperature exceeds a certain threshold.
TRAP-TYPE    

a3ComSysPowerSupplyFailureEvent 2
The trap that is generated when a power supply unit fails.
TRAP-TYPE    

a3ComSysChassisSlotOverTemperatureEvent 3
The trap that is generated when the temperature of a board in a particular slot exceeds a certain threshold.
TRAP-TYPE    

a3ComSysChassisSlotInsertEvent 4
The trap that is generated when a board is inserted into a particular slot.
TRAP-TYPE    

a3ComSysChassisSlotExtractEvent 5
The trap that is generated when a board is extracted from a particular slot.
TRAP-TYPE    

a3ComSysBridgeAddressThresholdEvent 6
The trap that is generated when the number of addresses stored in the bridge reaches a3ComSysBridgeAddressThreshold.
TRAP-TYPE    

a3ComSysSystemFanFailureEvent 7
The trap that is generated when one of the system fans fails.
TRAP-TYPE    

a3ComSysModuleCardSysOverTemperatureEvent 8
The trap that is generated when the temperature of the system exceeds a certain threshold. This trap is generated from agents that support the a3ComSysModuleCardInfoTable.
TRAP-TYPE    

a3ComSysModuleCardInsertEvent 9
The trap that is generated when a board is inserted into a particular modular slot. This trap is generated from agents that support the a3ComSysModuleCardInfoTable.
TRAP-TYPE    

a3ComSysModuleCardExtractEvent 10
The trap that is generated when a board is extracted from a particular modular slot. This trap is generated from agents that support the a3ComSysModuleCardInfoTable.
TRAP-TYPE