-- -- Copyright (c) 1995-19966 by cisco Systems, Inc. -- All rights reserved. -- -------------------------------------------------------------------- LS100-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises, Counter FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212; -- ciscoLS100Mib MODULE-IDENTITY -- LAST-UPDATED "9603120000Z" -- ORGANIZATION "Cisco Systems, Inc." -- CONTACT-INFO -- " Cisco Systems -- Customer Service -- -- Postal: 170 W Tasman Drive -- San Jose, CA 95134 -- USA -- -- Tel: +1 800 553-NETS -- -- E-mail: cs-atm@cisco.com" -- DESCRIPTION -- "The MIB for the Cisco/NEC LS100 ATM switch -- (formerly known as the A100)." -- REVISION "9603120000Z" -- DESCRIPTION -- "Updated to support the LS100 V3.x software." -- REVISION "9503200000Z" -- DESCRIPTION -- "Updated to support the LS100 V2.x software." -- REVISION "9411170000Z" -- DESCRIPTION -- "Initial version of this MIB module." -- ::= { xxx } DisplayString ::= OCTET STRING (SIZE (0..255)) -- from RFC1213-MIB nec OBJECT IDENTIFIER ::= { enterprises 119 } nec-mib OBJECT IDENTIFIER ::= { nec 2 } necProductDepend OBJECT IDENTIFIER ::= { nec-mib 3 } atomis-mib OBJECT IDENTIFIER ::= { necProductDepend 14 } m5core-mib OBJECT IDENTIFIER ::= { atomis-mib 3 } -- MIB Groups -- -- Node group node OBJECT IDENTIFIER ::= { m5core-mib 1 } -- Line interface group linf OBJECT IDENTIFIER ::= { m5core-mib 2 } -- Connection group conn OBJECT IDENTIFIER ::= { m5core-mib 3 } -- Performance group perf OBJECT IDENTIFIER ::= { m5core-mib 4 } -- The Node Group nodeOperStatus OBJECT-TYPE SYNTAX INTEGER { down(1), active(2), offLine(3), testing(4), initializing(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Operational status of the LS100." ::= { node 1 } nodeIfConfTable OBJECT-TYPE SYNTAX SEQUENCE OF NodeIfConfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The configuration of the line cards." ::= { node 2 } nodeIfConfEntry OBJECT-TYPE SYNTAX NodeIfConfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The configuration of a line card." INDEX { nodeIfConfIndex } ::= { nodeIfConfTable 1 } NodeIfConfEntry ::= SEQUENCE { nodeIfConfIndex INTEGER, nodeIfConfPhysType INTEGER, nodeIfConfRev DisplayString, nodeIfConfStatus INTEGER } nodeIfConfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index of the table. Same as ifIndex." ::= { nodeIfConfEntry 1 } nodeIfConfPhysType OBJECT-TYPE SYNTAX INTEGER { other(1), sar(2), taxi100M(3), oc3cSMF(4), oc3cMMF(5), ds3PlcpScramble(6), ds3PlcpNoScramble(7), relay6Mcell(8), ds3Scramble(9), ds3NoScramble(10), e3PlcpScramble(11), e3PlcpNoScramble(12), e3Scramble(13), e3NoScramble(14), utp5(15), leasedLine3M(16), leasedLine4M(17), leasedLine6M(18), utp5classB(19), oc3cSmfShaper(20), taxi140M(21), notInstalled(99) } ACCESS read-only STATUS mandatory DESCRIPTION "The PMD/physical layer format of the line card." ::= { nodeIfConfEntry 2 } nodeIfConfRev OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The revision of the line cards." ::= { nodeIfConfEntry 3 } nodeIfConfStatus OBJECT-TYPE SYNTAX INTEGER { other(1), inService(2), outOfService(3), testing(4), localLoopBack(5), remoteLoopBack(6), notInstalled(99) } ACCESS read-only STATUS mandatory DESCRIPTION "Operational status of the line card." ::= { nodeIfConfEntry 4 } nodeFanStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Operational status of the Fan." ::= { node 3 } nodeUpcWindowSize OBJECT-TYPE SYNTAX INTEGER (1..120) ACCESS read-write STATUS mandatory DESCRIPTION "UPC window size. Integer Wi represents Wi X 512 cell time. Wi=1 correspond to 1.4msec. Wi=120 correspond to 168msec. It is not allowed to change window size when any PVC exists." ::= { node 4 } nodeBestEffortBufferSize OBJECT-TYPE SYNTAX INTEGER (0..16) ACCESS read-write STATUS mandatory DESCRIPTION "Input buffer capacity for Best Effort traffic(Bb). The number of cells stored in the buffer is Bb X 128. The default value is 8. The sum of the buffer capacity is 2047 cells." ::= { node 5 } nodeGuaranteedBufferSize OBJECT-TYPE SYNTAX INTEGER (0..16) ACCESS read-write STATUS mandatory DESCRIPTION "Input buffer capacity for Guaranteed traffic(Bg). The number of cells stored in the buffer is Bg X 128. The default value is 0. The sum of the buffer capacity is 2047 cells." ::= { node 6 } nodeBestEffortBufferThreshold OBJECT-TYPE SYNTAX INTEGER (0..16) ACCESS read-write STATUS mandatory DESCRIPTION "Threshold buffer capacity for Best Effort traffic. If the number of cells stored in the buffer exceeds this threshold, cells with CLP=1 and traffic defined as UBR will be discarded." ::= { node 7 } nodeGuaranteedBufferThreshold OBJECT-TYPE SYNTAX INTEGER (0..16) ACCESS read-write STATUS mandatory DESCRIPTION "Threshold buffer capacity for Guaranteed traffic. If the number of cells stored in the buffer exceeds this threshold, cells with CLP=1 and traffic defined as VBR will be discarded." ::= { node 8 } nodeSaveConf OBJECT-TYPE SYNTAX INTEGER { save(1), noOperation(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Save system configuration information including the PVC table to the non-volatile memory. Writing a value of save(1) saves the configiration data. Writing the value noOperation(2) has no effect. When read, this object always has the value noOperation(2)." ::= { node 9 } nodeSaveResult OBJECT-TYPE SYNTAX INTEGER { temporaryFailure(1), notReady(2), ready(3), success(4), nearend(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the result of the save command issued from NMS. The result is either success/temporary failure/notReady." ::= { node 10 } nodeReset OBJECT-TYPE SYNTAX INTEGER { reset(1), noOperation(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Writing the value reset(1) resets the system. Writing the value noOperation(2) has no effect. When read, this object always has the value noOperation(2)." ::= { node 11 } -- The Linf Group linfStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF LinfStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Status of the line cards including ATM specific information." ::= { linf 1 } linfStatusEntry OBJECT-TYPE SYNTAX LinfStatusEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Status of a line card including ATM specific information." INDEX { linfIndex } ::= { linfStatusTable 1 } LinfStatusEntry ::= SEQUENCE { linfIndex INTEGER, linfStatus INTEGER, linfConf INTEGER, linfFwdAvailableBandWidth INTEGER, linfBkwdAvailableBandWidth INTEGER } linfIndex OBJECT-TYPE SYNTAX INTEGER(1..64) ACCESS read-only STATUS mandatory DESCRIPTION "Same as ifIndex" ::= { linfStatusEntry 1 } linfStatus OBJECT-TYPE SYNTAX INTEGER { normal(1), los(2), lof(3), loc(4), ais(5), yellowLine(6), yellowPath(7), lop(8), idle(9), yellowAlarm(10), plcpLOF(11), plcpYellow(12), maFERF(13), rai(14), payloadAllOnes(15), notInstalled(99) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of line interface" ::= { linfStatusEntry 2 } linfConf OBJECT-TYPE SYNTAX INTEGER { publicUNI(1), privateUNI(2), privateNNI(3), others(99) } ACCESS read-write STATUS mandatory DESCRIPTION "Line card type." ::= { linfStatusEntry 3 } linfFwdAvailableBandWidth OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The amount of bandwidth (Mbps) available/unallocated in the forward (incoming) direction." ::= { linfStatusEntry 4 } linfBkwdAvailableBandWidth OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The amount of bandwidth (Mbps) available/unallocated in the backward (outgoing) direction." ::= { linfStatusEntry 5 } -- The Conn (Connection & Traffic for accounting) Group connPvcIndexNext OBJECT-TYPE SYNTAX INTEGER (0..8191) ACCESS read-only STATUS mandatory DESCRIPTION "The next available index for a row of the connPvcTable." ::= { conn 1 } connPvcIndexEnable OBJECT-TYPE SYNTAX INTEGER (0..8191) ACCESS read-write STATUS deprecated DESCRIPTION "When read, this object is the current minimum value of an index in the connPvcTable. Writing this value has no effect." ::= { conn 2 } connPvcTable OBJECT-TYPE SYNTAX SEQUENCE OF ConnPvcEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table containing information on current PVC/SVCs. Currently, only PVCs are represented in this table. The table is also used to establish and delete PVCs. 1. PVC establishment procedure (1) Read connPvcIndexNext. This value is used as the value of connPvcIndex for the new connection. (2) Determine the value of connPvcHighIfIndex. When creating a new point-to-multipoint connection, connPvcHighIfIndex must identify the first leaf. When creating a new point-to-point connection, connPvcHighIfIndex normally identifies the interface with the higher value of ifIndex. (3) Set connPvcRowStatus to 'createAndWait' using the values of connPvcIndex and connPvcHighIfIndex as indexes. This causes the switch to create the new row with some objects being set to default values. The parameters for which there is no reasonable default are set to 0xffffffff. Object Default connPvcTopology bidirectionalVCC(2) connPvcTrafficType trafficUBR(4) connPvcLowIfIndex 0xffffffff connPvcLowVPI 0xffffffff connPvcLowVCI 0xffffffff connPvcLowUpcParam 512 connPvcLowUpc pass(1) connPvcLowThroughput 0 connPvcHighVPI 0xffffffff connPvcHighVCI 0xffffffff connPvcHighUpcParam 512 connPvcHighUpc pass(1) connPvcHighThroughput 0 The switch then sets the value of connPvcRowStatus to 'notReady'. The default values can be read by the NMS. (4) The values of the above objects which are set to 0xffffffff must be modified, and the values of any other objects can be changed. When establishing a VP connection, connPvcLowVCI and connPvcHighVCI should be set to 0. When connPvcTrafficType is set to trafficUBR, the values of connPvcLowThroughput and connPvcHighThroughput are ignored. When all parameters have acceptable values, the switch sets connPvcRowStatus to 'notInService'. (5) When the NMS sets connPvcRowStatus to 'active', the switch validates each parameter's value, and tries to establish the connection. If this operation fails, the the cause of the failure is indicated by the value of connPvcCause. At present, the switch allows connPvcRowStatus to have a value of notReady or notInService for only one row at a time. 2. Adding a new leaf to an existing pt-to-mpt connection (1) Determine the value of connPvcIndex for the existing point-to-multipoint connection to which a new leaf is to be added. (2) Determine the value of connPvcHighIfIndex as the ifIndex value of the interface to be used for the new leaf. (3) Set connPvcRowStatus to 'createAndWait' using the values of connPvcIndex and connPvcHighIfIndex as indexes. This causes the switch to create the new leaf with some objects being set to default values. The parameters for which there is no reasonable default are set to 0xffffffff. Object Default connPvcHighVPI 0xffffffff connPvcHighVCI 0xffffffff connPvcHighUpcParam 512 connPvcHighUpc pass(1) connPvcHighThroughput 0 The switch then sets the value of connPvcRowStatus to 'notReady'. The default values can be read by the NMS. (4) The NMS must modify the values of connPvcHighVPI and connPvcHighVCI, and can modify the values of connPvcHighUpc, connPvcHighUpcParam and connPvcHighThroughput. When establishing a VP connection, connPvcHighVCI should be set to 0. The NMS should not change the values of the following objects: connPvcTopology connPvcTrafficType connPvcLowIfIndex connPvcLowVPI connPvcLowVCI connPvcLowUpcParam connPvcLowUpc connPvcLowThroughput When all parameters have acceptable values, the switch sets connPvcRowStatus to 'notInService'. (5) When the NMS sets connPvcRowStatus to 'active', the switch validates each parameter's value, and tries to add the new leaf to the original connection. If this operation fails, the cause of the failure is indicated by the value of connPvcCause. 3. PVC deletion procedure (1) Set the connPvcRowStatus to 'destroy'. If the row exists but is impossible to delete, the cause of the failure is indicated by the value of connPvcCause. If the deletion is successful, the row is deleted (including the instance of connPvcCause for that row). Notes: - a row representing a terminating VP will not have instances of the following objects: connPvcLowUpc, connPvcLowUpcParam, connPvcLowThroughput, connPvcHighUpc, connPvcHighUpcParam, connPvcHighThroughput, connPvcLowOutCells, connPvcHighInCells, connPvcHighUpcViolatedCells, connPvcLowInCells, connPvcHighOutCells, and connPvcLowUpcViolatedCells. - a row representing a connection between the gateway-PAD (the switch's internal port) and a line interface will not have instances of the following objects: connPvcLowUpc, connPvcLowUpcParam, connPvcLowThroughput, connPvcHighUpc, connPvcHighUpcParam, connPvcHighThroughput, connPvcHighOutCells, connPvcHighInCells, and connPvcHighUpcViolatedCells." ::= { conn 3 } connPvcEntry OBJECT-TYPE SYNTAX ConnPvcEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A row in the table is used to show the current PVC/SVCs." INDEX { connPvcIndex, connPvcHighIfIndex } ::= { connPvcTable 1 } ConnPvcEntry ::= SEQUENCE { connPvcIndex INTEGER, connPvcTopology INTEGER, connPvcTrafficType INTEGER, connPvcLowIfIndex INTEGER, connPvcLowVPI INTEGER, connPvcLowVCI INTEGER, connPvcLowUpcParam INTEGER, connPvcLowUpc INTEGER, connPvcLowThroughput INTEGER, connPvcHighIfIndex INTEGER, connPvcHighVPI INTEGER, connPvcHighVCI INTEGER, connPvcHighUpcParam INTEGER, connPvcHighUpc INTEGER, connPvcHighThroughput INTEGER, connPvcLowInCells Counter, connPvcHighOutCells Counter, connPvcHighInCells Counter, connPvcLowOutCells Counter, connPvcLowUpcViolatedCells Counter, connPvcHighUpcViolatedCells Counter, connPvcRowStatus INTEGER, connPvcCause INTEGER, connPvcKind INTEGER } connPvcIndex OBJECT-TYPE SYNTAX INTEGER (0..8191) ACCESS read-only STATUS mandatory DESCRIPTION "A unique value to identify this point-to-point or point-to-multipoint connection. A point-to-multipoint connection has multiple rows in this table, one for each leaf, each one having the same value of this object." ::= { connPvcEntry 1 } connPvcTopology OBJECT-TYPE SYNTAX INTEGER { uniDirectionalVCC(1), biDirectionalVCC(2), uniDirectionalVPC(3), biDirectionalVPC(4), broadcastVPC(5), broadcastVCC(6), gateway(7), -- connected to switch's internal port vpterm(8) } ACCESS read-write STATUS mandatory DESCRIPTION "Topology of the connection." ::= { connPvcEntry 2 } connPvcTrafficType OBJECT-TYPE SYNTAX INTEGER { trafficCBR(1), trafficVBR(2), trafficUBR(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Traffic Type." ::= { connPvcEntry 3 } connPvcLowIfIndex OBJECT-TYPE SYNTAX INTEGER (1..16) ACCESS read-write STATUS mandatory DESCRIPTION "The line interface number (ifIndex) of the low port. Normally, the low port has a lower ifIndex value than the high port. However, for point-to-multipoint connections, the root is always the low port, regardless of whether it is greater or smaller than the port numbers of individual leaves." ::= { connPvcEntry 4 } connPvcLowVPI OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "VPI value of the connection on the low port." ::= { connPvcEntry 5 } connPvcLowVCI OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "VCI value of the connection on the low port." ::= { connPvcEntry 6 } connPvcLowUpcParam OBJECT-TYPE SYNTAX INTEGER (0..512) ACCESS read-write STATUS mandatory DESCRIPTION "Number of cells allowed to be sent in the unit cell time (512 cell times)." ::= { connPvcEntry 7 } connPvcLowUpc OBJECT-TYPE SYNTAX INTEGER { pass(1), discard(2), tagging(3) -- notSupported } ACCESS read-write STATUS mandatory DESCRIPTION "The action to take on a UPC violation for this connection on the low port. The tagging action is not supported by current hardware." ::= { connPvcEntry 8 } connPvcLowThroughput OBJECT-TYPE SYNTAX INTEGER (0..622) ACCESS read-write STATUS mandatory DESCRIPTION "Average rate of the connection (Mbps). Direction is from the low port to high port. This parameter is valid for the connection whose traffic type is CBR or VBR." ::= { connPvcEntry 9 } connPvcHighIfIndex OBJECT-TYPE SYNTAX INTEGER (1..17) ACCESS read-only STATUS mandatory DESCRIPTION "The line interface number (ifIndex) of the high port. Normally, the high port has a higher ifIndex value than the low port. However, for point-to-multipoint connections, the root is always the low port, regardless of whether it is greater or smaller than the port numbers of individual leaves. Line interface number 17 corresponds to gateway (the switch's internal port)." ::= { connPvcEntry 10 } connPvcHighVPI OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The VPI value of the connection on the high port." ::= { connPvcEntry 11 } connPvcHighVCI OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The VCI value of the connection on the high port." ::= { connPvcEntry 12 } connPvcHighUpcParam OBJECT-TYPE SYNTAX INTEGER (0..512) ACCESS read-write STATUS mandatory DESCRIPTION "Number of cells allowed to be sent in the unit cell time (512 cell times)." ::= { connPvcEntry 13 } connPvcHighUpc OBJECT-TYPE SYNTAX INTEGER { pass(1), discard(2), tagging(3) -- notSupported } ACCESS read-write STATUS mandatory DESCRIPTION "The action to take on a UPC violation for this connection on the high port. The tagging action is not supported by current hardware." ::= { connPvcEntry 14 } connPvcHighThroughput OBJECT-TYPE SYNTAX INTEGER (0..622) ACCESS read-write STATUS mandatory DESCRIPTION "Average rate of the connection (Mbps). Direction is from the high port to low port. This parameter is valid for the connection whose traffic type is CBR or VBR." ::= { connPvcEntry 15 } connPvcLowInCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of incoming cells on this connection on low port." ::= { connPvcEntry 16 } connPvcHighOutCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of outgoing cells on this connection on the high port." ::= { connPvcEntry 17 } connPvcHighInCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of incoming cells on this connection on high port. (Valid for bi-direction connections only)." ::= { connPvcEntry 18 } connPvcLowOutCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of outgoing cells on this connection on the low. port. (Valid for bi-direction connections only)." ::= { connPvcEntry 19 } connPvcLowUpcViolatedCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of UPC violation cells incoming from the low port." ::= { connPvcEntry 20 } connPvcHighUpcViolatedCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of UPC violation cells incoming from the high port. (Valid for bi-direction connections only)." ::= { connPvcEntry 21 } connPvcRowStatus OBJECT-TYPE SYNTAX INTEGER { active(1), notInService(2), notReady(3), createAndWait(5), destroy(6) } ACCESS read-write STATUS mandatory DESCRIPTION "The status of this row. 'active' indicates that the connection is in use. 'notInService' indicates that the row exists but the connection is not established. 'notReady' indicates that the row exists in the agent, but is missing information necessary in order to be established. 'createAndWait' supplied by a management station wishing to create a new row. 'destroy' supplied by a management station wishing to delete the row." ::= { connPvcEntry 22 } connPvcCause OBJECT-TYPE SYNTAX INTEGER { existing(1), vpivciBusy(2), vpivciOutOfRange(3), rateOverFlow(4), upvpOutOfRange(5), broadcastTableFull(6), inconsistentVPVC(7), lineDiagnosis(8) } ACCESS read-only STATUS mandatory DESCRIPTION "The result of the PVC establishment/deletion." ::= { connPvcEntry 23 } connPvcKind OBJECT-TYPE SYNTAX INTEGER { pvc(1), svc(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This object identifies the connection is SVC or PVC." ::= { connPvcEntry 24 } -- The Perf (Performance) Group perfTrapEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The status of performance monitoring traps. Its value does not affect other traps, such as coldStart." ::= { perf 1 } perfIfTable OBJECT-TYPE SYNTAX SEQUENCE OF PerfIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of performance monitoring information." ::= { perf 2 } perfIfEntry OBJECT-TYPE SYNTAX PerfIfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Performance monitoring information for a specific line." INDEX { perfIfIndex } ::= { perfIfTable 1 } PerfIfEntry ::= SEQUENCE { perfIfIndex INTEGER, perfIfLcvs Counter, perfIfParitySections Counter, perfIfParityLines Counter, perfIfParityPaths Counter, perfIfHecErrors Counter, perfIfMisDelivdCells Counter, perfIfOverFlowCells Counter, perfIfInCBRCells Counter, perfIfOutCBRCells Counter, perfIfInVBRCells Counter, perfIfOutVBRCells Counter, perfIfInUBRCells Counter, perfIfOutUBRCells Counter } perfIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Line interface number. Same as ifIndex." ::= { perfIfEntry 1 } perfIfLcvs OBJECT-TYPE SYNTAX Counter ACCESS read-only -- not available in current release STATUS mandatory DESCRIPTION "Line Code Violation. This object is valid only for DS3/E3." ::= { perfIfEntry 2 } perfIfParitySections OBJECT-TYPE SYNTAX Counter ACCESS read-only -- not available in current release STATUS mandatory DESCRIPTION "Number of B1 (BIP) errors(OC-3c, UTP-5), Number of C-bit parity violation(DS3), Number of CRC-6 violation(DS1)." ::= { perfIfEntry 3 } perfIfParityLines OBJECT-TYPE SYNTAX Counter ACCESS read-only -- not available in current release STATUS mandatory DESCRIPTION "Number of B2 (BIP) errors(OC-3c, UTP-5), Number of P-bit parity violation(DS3)." ::= { perfIfEntry 4 } perfIfParityPaths OBJECT-TYPE SYNTAX Counter ACCESS read-only -- not available in current release STATUS mandatory DESCRIPTION "Number of B3 (BIP) errors(OC-3c, UTP-5), Number of PLCP BIP violation(DS3)." ::= { perfIfEntry 5 } perfIfHecErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of HEC errors detected." ::= { perfIfEntry 6 } perfIfMisDelivdCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of misdelivered cells." ::= { perfIfEntry 7 } perfIfOverFlowCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of cells discarded due to buffer overflow." ::= { perfIfEntry 8 } perfIfInCBRCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of received CBR cells." ::= { perfIfEntry 9 } perfIfOutCBRCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of transmitted CBR cells." ::= { perfIfEntry 10 } perfIfInVBRCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of received VBR cells." ::= { perfIfEntry 11 } perfIfOutVBRCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of transmitted VBR cells." ::= { perfIfEntry 12 } perfIfInUBRCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of received UBR cells." ::= { perfIfEntry 15 } perfIfOutUBRCells OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of transmitted UBR cells." ::= { perfIfEntry 16 } END