-- ======================================================================== -- Start - JUNIPER-WX-EVENT-MIB Module JUNIPER-WX-EVENT-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE FROM SNMPv2-SMI DisplayString FROM SNMPv2-TC jnxWxGrpEvents FROM JUNIPER-WX-GLOBAL-MIB; ------------------------------ -- Events Group -- ------------------------------ jnxWxGrpEventV2 OBJECT-IDENTITY STATUS current DESCRIPTION " Branch for SNMPv2 events. The OIDs for SNMPv2 events should have a zero as the next-to-last sub-identifier (as specified in RFC1902). " ::= { jnxWxGrpEvents 0 } -- Objects sent only in events jnxWxGrpEventDescr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION " String that provides a textual description of the event. " ::= { jnxWxGrpEvents 1 } -- Event descriptions jnxWxGrpEventPowerSupplyFailure NOTIFICATION-TYPE STATUS current DESCRIPTION "One or more sources of power to the system have failed. A redundant power-supply has presumably taken over. " ::= { jnxWxGrpEventV2 1 } jnxWxGrpEventPowerSupplyOk NOTIFICATION-TYPE STATUS current DESCRIPTION "One or more previously failed sources of power is now working normally. The transition to normal condition happened without the system having to be restarted. " ::= { jnxWxGrpEventV2 2 } jnxWxGrpEventLicenseWillExpire NOTIFICATION-TYPE OBJECTS { jnxWxGrpEventDescr } STATUS current DESCRIPTION "The license for the system is about to expire shortly. When it eventually does expire, the system will switch over to and stay in pass-through mode." ::= { jnxWxGrpEventV2 3 } jnxWxGrpEventThruputLimitExceeded NOTIFICATION-TYPE OBJECTS { jnxWxGrpEventDescr } STATUS current DESCRIPTION "The throughput of traffic through the device has exceeded the limit for which it has been licensed." ::= { jnxWxGrpEventV2 4 } jnxWxGrpEventLicenseExpired NOTIFICATION-TYPE OBJECTS { jnxWxGrpEventDescr } STATUS current DESCRIPTION "The license for the system expired. As a result, the system will switch over to and stay in pass-through mode." ::= { jnxWxGrpEventV2 5 } jnxWxGrpEventClientLimitExceeded NOTIFICATION-TYPE OBJECTS { jnxWxGrpEventDescr } STATUS current DESCRIPTION "Exceeded licensed maximum concurrent client connections. Please contact Juniper Networks to obtain a new license with higher number of concurrent client connections." ::= { jnxWxGrpEventV2 6 } jnxWxGrpEventInFailSafeMode NOTIFICATION-TYPE STATUS current DESCRIPTION "This trap is sent when the device boots up in fail-safe mode. This can happen for one of the following reasons: Fail-safe reboot was explicitly initiated by the user. The device rebooted automatically too many times because of the failure of internal consistency checks or the failure of tests that verify proper operation of the device." ::= { jnxWxGrpEventV2 7 } jnxWxGrpEventInterfaceSpeedMismatch NOTIFICATION-TYPE OBJECTS { jnxWxGrpEventDescr } STATUS current DESCRIPTION "A mismatch is detected between the local and remote interface settings. This can happen due to a mismatch in the local and remote interface speed or mode. " ::= { jnxWxGrpEventV2 8 } jnxWxGrpEventInterfaceSpeedOk NOTIFICATION-TYPE OBJECTS { jnxWxGrpEventDescr } STATUS current DESCRIPTION "A mismatch previously detected between the local and remote interface settings is now resolved. The local and remote interface speed and mode are matched. " ::= { jnxWxGrpEventV2 9 } jnxWxGrpEventInterfaceDuplexMismatch NOTIFICATION-TYPE OBJECTS { jnxWxGrpEventDescr } STATUS current DESCRIPTION "A possible mismatch was detected between the duplex settings of either the local or remote interface and that of the device attached to that interface. The interface (local or remote) is identified by the 'ifIndex' object. Note that this notification is quite different from jnxWxGrpEventInterfaceSpeedMismatch, which compares the local and remote interfaces on the same WX device." ::= { jnxWxGrpEventV2 10 } jnxWxGrpEventLoginFailure NOTIFICATION-TYPE OBJECTS { jnxWxGrpEventDescr } STATUS current DESCRIPTION "A user's login attempt via the console/ssh/web server failed due to incorrect username or password." ::= { jnxWxGrpEventV2 11 } jnxWxGrpEventDiskFailure NOTIFICATION-TYPE OBJECTS { jnxWxGrpEventDescr } STATUS current DESCRIPTION "A hard disk failed on the system. The system was rebooted, and will now operate without the downed disk, at a degraded performance. Dictionary accumulated until this point was lost." ::= { jnxWxGrpEventV2 12 } END -- END - Juniper-WX-EVENT-MIB objects -- ========================================================================