-- -- Juniper Enterprise Specific MIB: TWAMP MIB -- -- Copyright (c) 2007, Juniper Networks, Inc. -- All rights reserved. -- -- The contents of this document are subject to change without notice. -- JUNIPER-TWAMP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Integer32 FROM SNMPv2-SMI -- RFC2578 NOTIFICATION-TYPE, OBJECT-IDENTITY,IpAddress FROM SNMPv2-SMI DateAndTime, TEXTUAL-CONVENTION, DisplayString FROM SNMPv2-TC CounterBasedGauge64 FROM HCNUM-TC pingCtlOwnerIndex, pingCtlTestName, pingProbeHistoryIndex FROM DISMAN-PING-MIB jnxTwampMibRoot, jnxTwampNotificationPrefix FROM JUNIPER-SMI SnmpAdminString FROM SNMP-FRAMEWORK-MIB; jnxTwampMib MODULE-IDENTITY LAST-UPDATED "201403010000Z" ORGANIZATION "Juniper Networks, Inc." CONTACT-INFO " Juniper Technical Assistance Center Juniper Networks, Inc. 1194 N. Mathilda Avenue Sunnyvale, CA 94089 E-mail: support@juniper.net" DESCRIPTION "This mib provides data associated with the TWAMP feature" -- revision history REVISION "201403010000Z" DESCRIPTION "Initial definition." ::= { jnxTwampMibRoot 1 } JnxTwampClientCollectionType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Each TWAMP entry can maintain several collections of probes and provide separate calculations over each collection. The types of collections include: currentTest -- the test currently being executed lastCompletedTest -- the most recently completed test movingAverage -- the 'n' most recent probes (n is configurable) allTests -- all the probes (since the entry was last reset). Objects with this type identify a specific collection." SYNTAX INTEGER { currentTest (1), lastCompletedTest (2), movingAverage (3), allTests (4) } JnxTwampClientMeasurementType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "For each individual probe, several different measurements can be made. These include the following (all measurements are provided in units of microseconds): roundTripTime -- this is the delay between the the transmission of a probe and the arrival of its response. rttJitter -- this is the difference between the current round trip time measurement and the previous one. rttInterarrivalJitter -- An estimate of the statistical variance of a packet's interarrival time. Defined in rfc1889 as: J=J+(|D(i-1,i)|-J)/16 where J is the interarrival jitter and D(i-1, i) is the current round trip jitter measurement. egress -- this is the delay beween the transmission of a probe and its arrival at its destination. egressJitter -- this is the difference between the current egress delay the previous measurement. egressInterarrivalJitter -- similar to rttInterarrivalJitter, but applied to egress jitter measurements. ingress -- this is the delay between the transmission of a probe response and its arrival at its destination. ingressJitter -- this is the difference between the current ingress delay and the previous measurement. ingressInterarrivalJitter -- similar to rttInterarrivalJitter, but applied to ingress jitter measurements. Note, due to clock synchronization artifacts, many one-way jitter measurements & calculations may include signifacant variations, in some cases orders of magnitude greater than the round trip times. Because of this, one-way jitter measurements will only be performed on samples which are less than 10 seconds apart." SYNTAX INTEGER { roundTripTime (1), rttJitter (2), rttInterarrivalJitter (3), egress (4), egressJitter (5), egressInterarrivalJitter (6), ingress (7), ingressJitter (8), ingressInterarrivalJitter (9) } JnxTwampClientMeasurementSet ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Over each collection of probes, TWAMP calculates statistics for several sets of measurements. These sets include the following: roundTripTime -- the set of round trip delays posRttJitter -- the set of positive round trip jitter measurements negRttJitter -- the set of negative round trip jitter measurements egress -- the set of outgoing (source to destination) one-way delays posEgressJitter -- the set of positive egress jitter measurements negEgressJitter -- the set of negative egress jitter measurements ingress -- the set of incoming (destination to source) one-way delays posIngressJitter -- the set of positive ingress jitter measurements negIngressJitter -- the set of negative ingress jitter measurements Objects with this type identify a specific set of measurements." SYNTAX INTEGER { roundTripTime (1), posRttJitter (2), negRttJitter (3), egress (4), posEgressJitter (5), negEgressJitter (6), ingress (7), posIngressJitter (8), negIngressJitter (9) } JnxTwampPercentType ::= TEXTUAL-CONVENTION DISPLAY-HINT "d-6" STATUS current DESCRIPTION "Displays a percentage as decimal with 6 digits precision." SYNTAX Unsigned32(0..100000000) jnxTwampClientNode OBJECT-IDENTITY STATUS current DESCRIPTION "The node contains all the TWAMP client related tables." ::= {jnxTwampMib 1} jnxTwampRpmIdentity OBJECT-TYPE SYNTAX INTEGER { rpm(1), twamp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object is added to be binded to the traps. This object simply identifies if its an RPM type of test or a TWAMP type of test." ::= {jnxTwampMib 2} -- -- Sample Results Table -- jnxTwampClientResultsSampleTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxTwampClientResultsSampleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides measurements from the latest individual TWAMP probe samples. Within each sample, the specific measurement type is identified by jnxTwampClientResSampleType. Note, if the latest probe was unsuccessful, no measurement types will be available. See the definition of JnxTwampClientMeasurementType for details on the types of measurements available." ::= { jnxTwampClientNode 1 } jnxTwampClientResultsSampleEntry OBJECT-TYPE SYNTAX JnxTwampClientResultsSampleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry provides a specific measurement type for a single probe." INDEX { pingCtlOwnerIndex, pingCtlTestName, jnxTwampResSampleType } ::= { jnxTwampClientResultsSampleTable 1 } JnxTwampClientResultsSampleEntry ::= SEQUENCE { jnxTwampResSampleType JnxTwampClientMeasurementType, jnxTwampResSampleValue Integer32, jnxTwampResSampleDate DateAndTime } jnxTwampResSampleType OBJECT-TYPE SYNTAX JnxTwampClientMeasurementType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the specific measurement type returned by jnxTwampResSampleValue." ::= { jnxTwampClientResultsSampleEntry 1 } jnxTwampResSampleValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the measurement identified by the corresponding jnxTwampResSampleType." ::= { jnxTwampClientResultsSampleEntry 2 } jnxTwampResSampleDate OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the date and time of when this measurement was obtained." ::= { jnxTwampClientResultsSampleEntry 3 } -- -- Summary Results Table -- jnxTwampClientResultsSummaryTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxTwampClientResultsSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides a summary of the results for a specific TWAMP entry (identified by pingCtlOwnerIndex/pingCtlTestName). The scope of the summary is identified by jnxTwampClientResSumCollection." ::= { jnxTwampClientNode 2 } jnxTwampClientResultsSummaryEntry OBJECT-TYPE SYNTAX JnxTwampClientResultsSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in the table provides a summary of the TWAMP results over a single collection of probes(test session). For each TWAMP entry, there are several collections maintained: the current test, the most recently completed test, a configurable number of the most recent probes (aka 'moving average'), and a global collection representing all the probes. Each entry in this table summarizes the results for one of these collections." INDEX { pingCtlOwnerIndex, pingCtlTestName, jnxTwampResSumCollection } ::= { jnxTwampClientResultsSummaryTable 1 } JnxTwampClientResultsSummaryEntry ::= SEQUENCE { jnxTwampResSumCollection JnxTwampClientCollectionType, jnxTwampResSumSent Unsigned32, jnxTwampResSumReceived Unsigned32, jnxTwampResSumPercentLost JnxTwampPercentType, jnxTwampResSumDate DateAndTime } jnxTwampResSumCollection OBJECT-TYPE SYNTAX JnxTwampClientCollectionType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifes the collection of probes over which the summary data represented by the other objects in this table applies. Note, if a collection type is not supported or not configured, it will not be instantiated in this table." ::= { jnxTwampClientResultsSummaryEntry 1 } jnxTwampResSumSent OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the number of probes sent within the collection identified by jnxTwampResSumCollection." ::= { jnxTwampClientResultsSummaryEntry 2 } jnxTwampResSumReceived OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the number of probes received within the collection identified by jnxTwampResSumCollection." ::= { jnxTwampClientResultsSummaryEntry 3 } jnxTwampResSumPercentLost OBJECT-TYPE SYNTAX JnxTwampPercentType MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the percentage of probes lost within the collection identified by jnxTwampResSumCollection." ::= { jnxTwampClientResultsSummaryEntry 4 } jnxTwampResSumDate OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the date and time of when the most recent probe within the collection identified by jnxTwampResSumCollection was completed." ::= { jnxTwampClientResultsSummaryEntry 5 } --- --Calculated Results Table -- jnxTwampClientResultsCalculatedTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxTwampClientResultsCalculatedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides a set of calculated values for each TWAMP entry, for each collection of probes maintained within that entry, and for each supported measurement set within that collection of probes. This table will skip over any measurement set for which there are 0 samples." ::= { jnxTwampClientNode 3 } jnxTwampClientResultsCalculatedEntry OBJECT-TYPE SYNTAX JnxTwampClientResultsCalculatedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { pingCtlOwnerIndex, pingCtlTestName, jnxTwampResSumCollection, jnxTwampResCalcSet } ::= { jnxTwampClientResultsCalculatedTable 1 } JnxTwampClientResultsCalculatedEntry ::= SEQUENCE { jnxTwampResCalcSet JnxTwampClientMeasurementSet, jnxTwampResCalcSamples Unsigned32, jnxTwampResCalcMin Unsigned32, jnxTwampResCalcMax Unsigned32, jnxTwampResCalcAverage Unsigned32, jnxTwampResCalcPkToPk Unsigned32, jnxTwampResCalcStdDev Unsigned32, jnxTwampResCalcSum CounterBasedGauge64 } jnxTwampResCalcSet OBJECT-TYPE SYNTAX JnxTwampClientMeasurementSet MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the measurement set upon which the calculations returned by the other objects in this table are based." ::= { jnxTwampClientResultsCalculatedEntry 1 } jnxTwampResCalcSamples OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of samples used in this calculations." ::= { jnxTwampClientResultsCalculatedEntry 2 } jnxTwampResCalcMin OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientResultsCalculatedEntry 3 } jnxTwampResCalcMax OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientResultsCalculatedEntry 4 } jnxTwampResCalcAverage OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The average of all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientResultsCalculatedEntry 5 } jnxTwampResCalcPkToPk OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The difference between the minimum and maximum of all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientResultsCalculatedEntry 6 } jnxTwampResCalcStdDev OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The standard deviation calculated over all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientResultsCalculatedEntry 7 } jnxTwampResCalcSum OBJECT-TYPE SYNTAX CounterBasedGauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientResultsCalculatedEntry 8 } -- -- History Sample Table -- jnxTwampClientHistorySampleTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxTwampClientHistorySampleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides measurements for individual TWAMP probe samples(test sessions). In addition to the last completed sample, a configurable number of the most recent samples are available as well. Within each sample, the specific measurement type is identified by jnxTwampHistSampleType. Note, if probe was unsuccessful, no measurement types will be available for that history entry. See the definition of JnxTwampClientMeasurementType for details on of measurements available." ::= { jnxTwampClientNode 4 } jnxTwampClientHistorySampleEntry OBJECT-TYPE SYNTAX JnxTwampClientHistorySampleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { pingCtlOwnerIndex, pingCtlTestName, pingProbeHistoryIndex, jnxTwampHistSampleType } ::= { jnxTwampClientHistorySampleTable 1 } JnxTwampClientHistorySampleEntry ::= SEQUENCE { jnxTwampHistSampleType JnxTwampClientMeasurementType, jnxTwampHistSampleValue Integer32 } jnxTwampHistSampleType OBJECT-TYPE SYNTAX JnxTwampClientMeasurementType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the specific measurement type returned by jnxTwampHistSampleValue." ::= { jnxTwampClientHistorySampleEntry 1 } jnxTwampHistSampleValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the measurement identified by the corresponding jnxTwampHistSampleType." ::= { jnxTwampClientHistorySampleEntry 2 } -- -- History Summary Table -- jnxTwampClientHistorySummaryTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxTwampClientHistorySummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides historical summary data for each collection of probes(test session) within each TWAMP Control Entry, similar to the jnxTwampClientResultsSummaryTable. In addition to the current summary, this table provides the same number of historical entries as the jnxTwampClientHistorySampleTable." ::= { jnxTwampClientNode 5 } jnxTwampClientHistorySummaryEntry OBJECT-TYPE SYNTAX JnxTwampClientHistorySummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { pingCtlOwnerIndex, pingCtlTestName, pingProbeHistoryIndex, jnxTwampHistSumCollection } ::= { jnxTwampClientHistorySummaryTable 1 } JnxTwampClientHistorySummaryEntry ::= SEQUENCE { jnxTwampHistSumCollection JnxTwampClientCollectionType, jnxTwampHistSumSent Unsigned32, jnxTwampHistSumReceived Unsigned32, jnxTwampHistSumPercentLost JnxTwampPercentType } jnxTwampHistSumCollection OBJECT-TYPE SYNTAX JnxTwampClientCollectionType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifies the collection of probes whose results are summarized by this row. At this time, historical summaries are available only for the current test (currentTest(1))." ::= { jnxTwampClientHistorySummaryEntry 1 } jnxTwampHistSumSent OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the number of probes sent within the collection identified by jnxTwampHistSumCollection." ::= { jnxTwampClientHistorySummaryEntry 2 } jnxTwampHistSumReceived OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the number of probes received within the collection identified by jnxTwampHistSumCollection." ::= { jnxTwampClientHistorySummaryEntry 3 } jnxTwampHistSumPercentLost OBJECT-TYPE SYNTAX JnxTwampPercentType MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the percentage of probes lost within the collection identified by jnxTwampHistSumCollection." ::= { jnxTwampClientHistorySummaryEntry 4 } -- -- History Calculated Table -- jnxTwampClientHistoryCalculatedTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxTwampClientHistoryCalculatedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides a set of calculated values for each TWAMP control entry, for each test session maintained within that entry, and for each supported calculated type within that collection of probes, similar to the jnxTwampClientResultsCalculatedTable. In addition to the current summary, this table provides the same number of historical entries as the jnxTwampClientHistorySampleTable." ::= { jnxTwampClientNode 6 } jnxTwampClientHistoryCalculatedEntry OBJECT-TYPE SYNTAX JnxTwampClientHistoryCalculatedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { pingCtlOwnerIndex, pingCtlTestName, pingProbeHistoryIndex, jnxTwampHistSumCollection, jnxTwampHistCalcSet } ::= { jnxTwampClientHistoryCalculatedTable 1 } JnxTwampClientHistoryCalculatedEntry ::= SEQUENCE { jnxTwampHistCalcSet JnxTwampClientMeasurementSet, jnxTwampHistCalcSamples Unsigned32, jnxTwampHistCalcMin Unsigned32, jnxTwampHistCalcMax Unsigned32, jnxTwampHistCalcAverage Unsigned32, jnxTwampHistCalcPkToPk Unsigned32, jnxTwampHistCalcStdDev Unsigned32, jnxTwampHistCalcSum CounterBasedGauge64 } jnxTwampHistCalcSet OBJECT-TYPE SYNTAX JnxTwampClientMeasurementSet MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the measurement set upon which the calculations returned by the other objects in this table are based." ::= { jnxTwampClientHistoryCalculatedEntry 1 } jnxTwampHistCalcSamples OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of samples used in this calculations." ::= { jnxTwampClientHistoryCalculatedEntry 2 } jnxTwampHistCalcMin OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum of all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientHistoryCalculatedEntry 3 } jnxTwampHistCalcMax OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum of all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientHistoryCalculatedEntry 4 } jnxTwampHistCalcAverage OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The average of all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientHistoryCalculatedEntry 5 } jnxTwampHistCalcPkToPk OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The difference between the minimum and maximum of all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientHistoryCalculatedEntry 6 } jnxTwampHistCalcStdDev OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The standard deviation calculated over all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientHistoryCalculatedEntry 7 } jnxTwampHistCalcSum OBJECT-TYPE SYNTAX CounterBasedGauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum of all the samples in the collection and measurement set associated with this row. Values are provided in units of microseconds." ::= { jnxTwampClientHistoryCalculatedEntry 8 } -- Control Sessions Table -- jnxTwampClientControlConnectionTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxTwampClientCCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Client Sessions." ::= { jnxTwampClientNode 7 } jnxTwampClientCCEntry OBJECT-TYPE SYNTAX JnxTwampClientCCEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "TWAMP Client Session characteristics." INDEX { jnxTwampClientControlConnectionID } ::= { jnxTwampClientControlConnectionTable 1 } JnxTwampClientCCEntry ::= SEQUENCE { jnxTwampClientControlConnectionID SnmpAdminString, jnxTwampClientCCName DisplayString, jnxTwampClientCCStatus INTEGER(0..65535), jnxTwampClientServerAddress IpAddress, jnxTwampClientServerPort INTEGER(0..65535), jnxTwampClientTSConfiguredCount INTEGER(0..65535), jnxTwampClientTSActiveCount INTEGER(0..65535), jnxTwampClientAuthMode INTEGER(0..65535) } jnxTwampClientControlConnectionID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "TWAMP Client control session ID." ::= { jnxTwampClientCCEntry 1 } jnxTwampClientCCName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Text string containing the session's unique name." ::= { jnxTwampClientCCEntry 2 } jnxTwampClientCCStatus OBJECT-TYPE SYNTAX INTEGER { active(1), stopped(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "If the control session is active, this would return 1. If the control session does not have any currently running test sessions and is not active, this would return 2." ::= { jnxTwampClientCCEntry 3 } jnxTwampClientServerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Server IP address for TWAMP TCP control session." ::= { jnxTwampClientCCEntry 4 } jnxTwampClientServerPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Destination port for TWAMP TCP control connection." ::= { jnxTwampClientCCEntry 5 } jnxTwampClientTSConfiguredCount OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Number test sessions configured." ::= { jnxTwampClientCCEntry 6 } jnxTwampClientTSActiveCount OBJECT-TYPE SYNTAX INTEGER(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of test sessions currently running." ::= { jnxTwampClientCCEntry 7 } jnxTwampClientAuthMode OBJECT-TYPE SYNTAX INTEGER { none(1), authenticated(2), encrypted(3), controlOnlyEncrypted(4) } MAX-ACCESS read-only STATUS current DESCRIPTION " Authenticated mode for the control session." ::= {jnxTwampClientCCEntry 8 } --- Table containing entries for all test sessions jnxTwampClientTestSessionsTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxTwampClientTSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Test Sessions." ::= {jnxTwampClientNode 8} jnxTwampClientTSEntry OBJECT-TYPE SYNTAX JnxTwampClientTSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "TWAMP Test Session characteristics." INDEX {pingCtlOwnerIndex, jnxTwampClientTestSessionID } ::= { jnxTwampClientTestSessionsTable 1 } JnxTwampClientTSEntry ::= SEQUENCE { jnxTwampClientTestSessionID SnmpAdminString, jnxTwampClientTSName DisplayString, jnxTwampClientTSStatus INTEGER, jnxTwampClientTSSenderAddress IpAddress, jnxTwampClientTSSenderPort INTEGER, jnxTwampClientTSReflectorAddress IpAddress, jnxTwampClientTSReflectorPort INTEGER } jnxTwampClientTestSessionID OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Test Session ID." ::= { jnxTwampClientTSEntry 1 } jnxTwampClientTSName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "TWAMP Test Session Name." ::= {jnxTwampClientTSEntry 2 } jnxTwampClientTSStatus OBJECT-TYPE SYNTAX INTEGER { active (1), stopped (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "TWAMP Test Session status." ::= {jnxTwampClientTSEntry 3 } jnxTwampClientTSSenderAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Twamp Test Sender Address." ::= {jnxTwampClientTSEntry 4 } jnxTwampClientTSSenderPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "TWAMP Test Session Sender Port." ::= {jnxTwampClientTSEntry 5 } jnxTwampClientTSReflectorAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "TWAMP Test Session Reflector Address." ::= {jnxTwampClientTSEntry 6} jnxTwampClientTSReflectorPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "TWAMP Test Session Reflector Port. " ::= {jnxTwampClientTSEntry 7 } twampNotifications OBJECT IDENTIFIER ::= {jnxTwampNotificationPrefix 1 } jnxTwampClientControlConnectionClosed NOTIFICATION-TYPE OBJECTS { jnxTwampClientCCName } STATUS current DESCRIPTION "This trap is generated when all the test iterations configured under the control connection finish running and control connection is closed." ::= {twampNotifications 1 } jnxTwampClientTestIterationFinished NOTIFICATION-TYPE OBJECTS { jnxTwampClientCCName } STATUS current DESCRIPTION "This trap is generated when one test iteration is finished for all the test sessions configured under the control connection." ::= {twampNotifications 2 } END