-- ******************************************************************* -- Juniper Services Network Address Translation (NAT) MIB. -- -- Copyright (c) 2010-2013, Juniper Networks, Inc. -- All rights reserved. -- -- The contents of this document are subject to change without notice. -- ******************************************************************* JUNIPER-NAT-MIB DEFINITIONS ::= BEGIN IMPORTS Gauge32, Integer32, Unsigned32, NOTIFICATION-TYPE, MODULE-IDENTITY, OBJECT-TYPE FROM SNMPv2-SMI InterfaceIndex FROM IF-MIB DateAndTime, DisplayString FROM SNMPv2-TC InetAddressType, InetAddress, InetAddressIPv4 FROM INET-ADDRESS-MIB jnxSvcsMibRoot FROM JUNIPER-SMI; jnxNatMIB MODULE-IDENTITY LAST-UPDATED "201007122022Z" -- July 12, 2010" ORGANIZATION "Juniper Networks, Inc." CONTACT-INFO "Juniper Technical Assistance Center Juniper Networks, Inc. 1194 N. Mathilda Avenue Sunnyvale, CA 94089 E-mail: support@juniper.net HTTP://www.juniper.net" DESCRIPTION "This module defines the object that are used to monitor network address translation attributes." REVISION "201007122022Z" -- July 12, 2010 DESCRIPTION "Creation Date" ::= { jnxSvcsMibRoot 1 } jnxNatNotifications OBJECT IDENTIFIER ::= { jnxNatMIB 0 } jnxNatObjects OBJECT IDENTIFIER ::= { jnxNatMIB 1 } jnxNatTrapVars OBJECT IDENTIFIER ::= { jnxNatMIB 2 } -- *************************************************************** -- Source NAT Table -- *************************************************************** jnxSrcNatStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxSrcNatStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table exposes the source NAT translation attributes of the translated addresses. When performing source IP address translation, the services pic translates the original source IP address and/or port number to different one. The resource, address source pools provide the service pic with a supply of addresses from which to draw when performing source network address translation. This table contains information on source IP address translation only." ::= { jnxNatObjects 1 } jnxSrcNatStatsEntry OBJECT-TYPE SYNTAX JnxSrcNatStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Source NAT address entries. It is indexed by the address pool table and the address allocated. " INDEX { jnxNatSrcPoolName } ::= { jnxSrcNatStatsTable 1 } JnxSrcNatStatsEntry ::= SEQUENCE { jnxNatSrcPoolName DisplayString, jnxNatSrcXlatedAddrType INTEGER, jnxNatSrcPoolType INTEGER, jnxNatSrcNumPortAvail Unsigned32, jnxNatSrcNumPortInuse Unsigned32, jnxNatSrcNumAddressAvail Unsigned32, jnxNatSrcNumAddressInUse Unsigned32, jnxNatSrcNumSessions Unsigned32 } jnxNatSrcPoolName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of dynamic source IP address pool. This is the address pool where the translated address is allocated from. " ::= { jnxSrcNatStatsEntry 1 } jnxNatSrcXlatedAddrType OBJECT-TYPE SYNTAX INTEGER { ipv4 (1), ipv6 (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of dynamic source IP address allocated from the address pool used in the NAT translation. For NAT MIB, supporting ipv4(1) and ipv6(2) only." ::= { jnxSrcNatStatsEntry 2 } jnxNatSrcPoolType OBJECT-TYPE SYNTAX INTEGER { static (1), dynamic-napt (2), dynamic-nat (3), basic-nat44 (11), dynamic-nat44 (12), napt-44 (13), dnat-44 (14), stateful-nat64 (15), stateless-nat64 (16), basic-nat-pt (17), napt-pt (18), basic-nat66 (19), stateless-nat66 (20), napt-66 (21), twice-napt-44 (22), twice-basic-nat-44 (23), twice-dynamic-nat-44 (24), det-napt44 (25), sd-napt44 (26) } MAX-ACCESS read-only STATUS current DESCRIPTION "Source NAT can do address translation with or without port translation. The source port pool type indicates whether the address translation is done with port or without the port, or if it is a static translation." ::= { jnxSrcNatStatsEntry 3 } jnxNatSrcNumPortAvail OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ports available with this pool." ::= { jnxSrcNatStatsEntry 4 } jnxNatSrcNumPortInuse OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ports in use for this NAT address entry. This attribute is only applicable to translation with port translation." ::= { jnxSrcNatStatsEntry 5 } jnxNatSrcNumAddressAvail OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of addresses available in this pool." ::= { jnxSrcNatStatsEntry 6 } jnxNatSrcNumAddressInUse OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of addresses in use from this pool. This attribute is only applicable to pools used with source dynamic translations." ::= { jnxSrcNatStatsEntry 7 } jnxNatSrcNumSessions OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of sessions are in use based on this NAT address entry." ::= { jnxSrcNatStatsEntry 8 } -- *************************************************************** -- NAT Rule Hit Table -- *************************************************************** jnxNatRuleTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxNatRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table monitors NAT rule hits " ::= { jnxNatObjects 2 } jnxNatRuleEntry OBJECT-TYPE SYNTAX JnxNatRuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "NAT rule hit entries. It is indexed by the rule index" INDEX { jnxNatRuleName } ::= { jnxNatRuleTable 1 } JnxNatRuleEntry ::= SEQUENCE { jnxNatRuleName DisplayString, jnxNatRuleType INTEGER, jnxNatRuleTransHits Unsigned32 } jnxNatRuleName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "NAT rule name" ::= { jnxNatRuleEntry 1 } jnxNatRuleType OBJECT-TYPE SYNTAX INTEGER { static-source (1), static-destination (2), dynamic-source (3), napt (4), basic-nat44 (11), dynamic-nat44 (12), napt-44 (13), dnat-44 (14), stateful-nat64 (15), stateless-nat64 (16), basic-nat-pt (17), napt-pt (18), basic-nat66 (19), stateless-nat66 (20), napt-66 (21), twice-napt-44 (22), twice-basic-nat-44 (23), twice-dynamic-nat-44 (24), det-napt44 (25), sd-napt44 (26) } MAX-ACCESS read-only STATUS current DESCRIPTION "NAT types: Static Source, Static Destination, Dynamic Source and NAPT" ::= { jnxNatRuleEntry 2 } jnxNatRuleTransHits OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of hits on this NAT rule" ::= { jnxNatRuleEntry 3 } -- *************************************************************** -- NAT Pool Hit Table -- *************************************************************** jnxNatPoolTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxNatPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table monitors NAT pool hits " ::= { jnxNatObjects 3 } jnxNatPoolEntry OBJECT-TYPE SYNTAX JnxNatPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "NAT pool hit entries. It is indexed by the pool index" INDEX { jnxNatPoolName } ::= { jnxNatPoolTable 1 } JnxNatPoolEntry ::= SEQUENCE { jnxNatPoolName DisplayString, jnxNatPoolType INTEGER, jnxNatPoolTransHits Unsigned32 } jnxNatPoolName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "NAT Pool name" ::= { jnxNatPoolEntry 1 } jnxNatPoolType OBJECT-TYPE SYNTAX INTEGER { static-source (1), static-destination (2), dynamic-source (3), napt (4), basic-nat44 (11), dynamic-nat44 (12), napt-44 (13), dnat-44 (14), stateful-nat64 (15), stateless-nat64 (16), basic-nat-pt (17), napt-pt (18), basic-nat66 (19), stateless-nat66 (20), napt-66 (21), twice-napt-44 (22), twice-basic-nat-44 (23), twice-dynamic-nat-44 (24), det-napt44 (25), sd-napt44 (26) } MAX-ACCESS read-only STATUS current DESCRIPTION "NAT types: Static Source, Static Destination, Dynamic Source and NAPT" ::= { jnxNatPoolEntry 2 } jnxNatPoolTransHits OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of hits on this NAT Pool" ::= { jnxNatPoolEntry 3 } -- *************************************************************** -- NAT Trap definition -- *************************************************************** -- *************************************************************** -- Trap variables -- *************************************************************** jnxNatAddrPoolUtil OBJECT-TYPE SYNTAX Integer32 (0..100) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The dynamic address pool utilization in terms of number of ports utilized." ::= { jnxNatTrapVars 1 } jnxNatTrapSrcPoolName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Source NAT Pool name who issues trap" ::= { jnxNatTrapVars 2 } -- *************************************************************** -- NAT Address Pool Utilization Threshold Status -- *************************************************************** jnxNatAddrPoolThresholdStatus NOTIFICATION-TYPE OBJECTS { jnxNatTrapSrcPoolName, jnxNatAddrPoolUtil } STATUS current DESCRIPTION "The Source NAT address pool utilization threshold status trap signifies that the address pool utilization is either exceeds threshold value, or clear of that value. jnxNatTrapPoolName is the name of the resource pool jnxNatAddrPoolUtil is the number of ports utilized of the address pool." ::= { jnxNatNotifications 1 } -- *************************************************************** -- END of File -- *************************************************************** END