-- ---------------------------------------------------------------------------- -- File Main Owner: -- File Peer Owner: -- File Description: Main entry point to build private MIBs. -- -- -- { COPYRIGHT / HISTORY -- -- -- -- PORTING HISTORY -- -- } COPYRIGHT / HISTORY (end) -- -- ---------------------------------------------------------------------------- -- { INSERT: blade -- ---------------------------------------------------------------------------- IBM-GbTOR-G8052-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, Integer32, Unsigned32, Counter32, Gauge32, Counter64, TimeTicks, IpAddress FROM SNMPv2-SMI DisplayString, PhysAddress, MacAddress, TruthValue, RowStatus FROM SNMPv2-TC BridgeId FROM BRIDGE-MIB sysName, sysLocation, sysContact, ifIndex FROM RFC1213-MIB enterprises FROM RFC1155-SMI InetAddressType, InetAddress, InetAddressIPv6 FROM INET-ADDRESS-MIB OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, Integer32, Unsigned32, Counter32, Gauge32, Counter64, TimeTicks, IpAddress, mib-2 FROM SNMPv2-SMI TEXTUAL-CONVENTION, TruthValue, DisplayString, PhysAddress, MacAddress, RowStatus, TimeInterval, TimeStamp, RowPointer, AutonomousType, StorageType, TDomain, TAddress FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF BridgeId, dot1dTp, dot1dTpPort, dot1dBridge, dot1dBasePortEntry, dot1dBasePort FROM BRIDGE-MIB EnabledStatus FROM P-BRIDGE-MIB PortList FROM Q-BRIDGE-MIB SnmpAdminString, SnmpEngineID,SnmpMessageProcessingModel, SnmpSecurityModel,SnmpSecurityLevel FROM SNMP-FRAMEWORK-MIB usmNoAuthProtocol, usmNoPrivProtocol FROM SNMP-USER-BASED-SM-MIB sysName, sysLocation, sysContact, ifIndex FROM RFC1213-MIB InterfaceIndex, InterfaceIndexOrZero FROM IF-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB ; -- ---------------------------------------------------------------------------- -- { INSERT: module identity -- ---------------------------------------------------------------------------- ibmGbTORG8052MIB MODULE-IDENTITY LAST-UPDATED "201605171703Z" -- May 17, 2016 05:03:02 PM ORGANIZATION "IBM/System Networking" CONTACT-INFO " IBM/System Networking 4400 North First Street San Jose, CA 95134 408-956-3239 " DESCRIPTION " MIB for IBM Networking Operating System RackSwitch G8052 All Rights reserved DEVICE VERSION: 7.9.17.0 " ::= { blade 3 } -- ---------------------------------------------------------------------------- -- } INSERT: module identity -- ---------------------------------------------------------------------------- -- ---------------------------------------------------------------------------- -- { INSERT: textual conventions -- ---------------------------------------------------------------------------- PortNumber ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents a port number of a switch." SYNTAX Unsigned32 VlanId ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "A 12-bit VLAN ID used in the VLAN Tag header." SYNTAX Integer32 (1..4094) Timeout ::= TEXTUAL-CONVENTION DISPLAY-HINT "d4" STATUS current DESCRIPTION " Time out value in 4 byte" SYNTAX Integer32 -- ---------------------------------------------------------------------------- -- } INSERT: textual conventions -- ---------------------------------------------------------------------------- -- blade OID reference http://www.iana.org/assignments/enterprise-numbers -- defined in /vobs/webos/src/lib/epi/target/h/wrn/wm/snmp/engine/mib.h blade OBJECT IDENTIFIER ::= { enterprises 26543 } -- Groups in blade registration OBJECT IDENTIFIER ::= { blade 1 } private-mibs OBJECT IDENTIFIER ::= { blade 2 } -- Access Switch for BNT Private MIBs -- bnt-switch OBJECT IDENTIFIER ::= { private-mibs 7 } -- ---------------------------------------------------------------------------- -- { INSERT: bntRoot -- ---------------------------------------------------------------------------- -- Access Web Switch Module for Private MIBs ibm-switch-mgmt OBJECT IDENTIFIER ::= { private-mibs 7 } g8052-mgmt OBJECT IDENTIFIER ::= { ibm-switch-mgmt 7 } ------------------------------------------------------------------------------- -- Platform Dependent Registration sysObjectID -- Must correspond to g_sysobjid in /vobs/webos/src//ts/mp/sys/config.c -- and defined in /vobs/webos/src/lib/epi/target/h/wrn/wm/snmp/engine/mib.h. -- Careful when re-numbering sysObjectIDs due to hard coded references in -- /vobs/webos/src//ts/mp/epi/trap.c ------------------------------------------------------------------------------- -- Top of Rack Switch ibm-switch OBJECT IDENTIFIER ::= { registration 7 } g8052 OBJECT IDENTIFIER ::= { ibm-switch 7 } -- G8052 switch ------------------------------------------------------------------------------- -- Platform Common Private MIBs for g8052-mgmt ------------------------------------------------------------------------------- agent OBJECT IDENTIFIER ::= { g8052-mgmt 1 } -- ---------------------------------------------------------------------------- -- { INSERT: agent -- ---------------------------------------------------------------------------- agentConfig OBJECT IDENTIFIER ::= { agent 1 } agentStats OBJECT IDENTIFIER ::= { agent 2 } agentInfo OBJECT IDENTIFIER ::= { agent 3 } agentOper OBJECT IDENTIFIER ::= { agent 4 } agSystem OBJECT IDENTIFIER ::= { agentConfig 1 } agPortConfig OBJECT IDENTIFIER ::= { agentConfig 2 } agRadiusConfig OBJECT IDENTIFIER ::= { agentConfig 3 } agNTP OBJECT IDENTIFIER ::= { agentConfig 4 } agSyslog OBJECT IDENTIFIER ::= { agentConfig 5 } agTransfer OBJECT IDENTIFIER ::= { agentConfig 7 } agApply OBJECT IDENTIFIER ::= { agentConfig 8 } agTacacsConfig OBJECT IDENTIFIER ::= { agentConfig 11 } agMgmtNetConfig OBJECT IDENTIFIER ::= { agentConfig 12 } agBoot OBJECT IDENTIFIER ::= { agentConfig 13 } agAccess OBJECT IDENTIFIER ::= { agentConfig 19 } agLdapConfig OBJECT IDENTIFIER ::= { agentConfig 21 } agSSHConfig OBJECT IDENTIFIER ::= { agentConfig 22 } agsFlowConfig OBJECT IDENTIFIER ::= { agentConfig 24 } agUSBCopy OBJECT IDENTIFIER ::= { agentConfig 25 } pktStats OBJECT IDENTIFIER ::= { agentStats 1 } mpCpuStats OBJECT IDENTIFIER ::= { agentStats 2 } portStats OBJECT IDENTIFIER ::= { agentStats 3 } agClearStats OBJECT IDENTIFIER ::= { agentStats 7 } ntpStats OBJECT IDENTIFIER ::= { agentStats 9 } aclStats OBJECT IDENTIFIER ::= { agentStats 11 } memoryStats OBJECT IDENTIFIER ::= { agentStats 12 } snmpStats OBJECT IDENTIFIER ::= { agentStats 20 } mpTcbStats OBJECT IDENTIFIER ::= { agentStats 21 } mpUdpStats OBJECT IDENTIFIER ::= { agentStats 22 } hardware OBJECT IDENTIFIER ::= { agentInfo 1 } portInfo OBJECT IDENTIFIER ::= { agentInfo 2 } agDiff OBJECT IDENTIFIER ::= { agentInfo 4 } agCfgDump OBJECT IDENTIFIER ::= { agentInfo 5 } geaportInfo OBJECT IDENTIFIER ::= { agentInfo 9 } sfpInfo OBJECT IDENTIFIER ::= { agentInfo 11 } accessInfo OBJECT IDENTIFIER ::= { agentInfo 13 } agNTPOper OBJECT IDENTIFIER ::= { agentOper 2 } -- There are two configuration blocks. -- The "current_config" reflects the configuration parameters that the -- switch is operating on and it is read-only. The objects with "CurCfg" -- in the name are reflect to this configuration block. -- -- The "new_config" accepts user configurations on set. The objects with -- "NewCfg" in the name are reflect to this configuration block. -- -- The newly set configurations will not take effect until a "apply" -- command has been issued (See agApplyConfiguration object) -- -- The newly set configurations will not be saved through next restarting -- of the switch unless a "save" command has been issued (See -- agSaveConfiguration object). -- Hardware Information hwPartNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The hardware part number of the Switch." ::= { hardware 1 } hwRevision OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The hardware revision. If the revision is not available, a zero length string should be returned." ::= { hardware 2 } hwFanStatus OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The fan status on the system." ::= { hardware 12 } hwFanSpeed OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The fan speed on the system." ::= { hardware 13 } hwTempSensors OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensors on the system." ::= { hardware 14 } hwGlobalHealthStatus OBJECT-TYPE SYNTAX INTEGER { ok(1), noncritical(2), critical(3) } MAX-ACCESS read-only STATUS current DESCRIPTION " This variable summarizes the status of several key elements of the device. OK: - When all temperature sensors are below the warning threshold (eg. for Fan rear to front direction < 60 C; for Fan front to rear direction < 55 C); - All 4 fan modules are good. A module is considered good if both fans in the module are running at >= 500 RPMs; - Both power supplies are on; - No panic dump exists in flash. Non-critical: - One or more temperature sensors are in the warning range (eg. for Fan rear to front direction >= 60 C and < 80C for Fan front to rear direction >= 55 and < 80 C); - A panic dump exists in flash. Critical: - One or more temperature sensors are in the failure range (eg. for Fan rear to front or front to rear direction >= 80 C); - There are < 3 good fan modules - One power supply is off. " ::= { hardware 15 } hwMainBoardRevision OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The main board revision. If the revision is not available, a zero length string should be returned." ::= { hardware 11 } hwESN OBJECT-TYPE SYNTAX DisplayString (SIZE(0..12)) MAX-ACCESS read-only STATUS current DESCRIPTION "The ESN of the switch." ::= { hardware 40 } -- Port operation table agPortOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AgPortOperTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of port operations." ::= { agentOper 1 } agPortOperTableEntry OBJECT-TYPE SYNTAX AgPortOperTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the port operations table." INDEX { portOperIdx } ::= { agPortOperTable 1 } AgPortOperTableEntry ::= SEQUENCE { portOperIdx PortNumber, portOperRmon INTEGER, portOperLearning INTEGER, portOperState INTEGER } portOperIdx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port index." ::= { agPortOperTableEntry 1 } portOperState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable port." ::= { agPortOperTableEntry 2 } portOperRmon OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable RMON for port." ::= { agPortOperTableEntry 3 } portOperLearning OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable L2 (FDB) Learning for this port." ::= { agPortOperTableEntry 4 } --portOperDot1x OBJECT IDENTIFIER ::= { agPortOperTableEntry 4 } portOperDot1xTable OBJECT-TYPE SYNTAX SEQUENCE OF PortOperDot1xTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of port operations." ::= { agentOper 4 } portOperDot1xTableEntry OBJECT-TYPE SYNTAX PortOperDot1xTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the port 802.1x operation table." INDEX { portOperDot1xIndx } ::= { portOperDot1xTable 1 } PortOperDot1xTableEntry ::= SEQUENCE { portOperDot1xIndx PortNumber, portOperDot1xReset INTEGER, portOperDot1xReauth INTEGER } portOperDot1xIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port index." ::= { portOperDot1xTableEntry 1 } portOperDot1xReset OBJECT-TYPE SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Reinitialize 802.1x access control on port." ::= { portOperDot1xTableEntry 2 } portOperDot1xReauth OBJECT-TYPE SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Initiate reauthentication on port." ::= { portOperDot1xTableEntry 3 } ntpOperSendReq OBJECT-TYPE SYNTAX INTEGER { no(1), yes(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Allows the user to send requests to the NTP server." ::= { agNTPOper 1 } -- Oper PRM settings agSrvLedOper OBJECT IDENTIFIER ::= { agentOper 5 } srvLedOper OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable Service Required LED." ::= { agSrvLedOper 1 } -- Port information table portInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF PortInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of port information." ::= { portInfo 1 } portInfoTableEntry OBJECT-TYPE SYNTAX PortInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the port information table." INDEX { portInfoIndx } ::= { portInfoTable 1 } PortInfoTableEntry ::= SEQUENCE { portInfoIndx PortNumber, portInfoSpeed INTEGER, portInfoMode INTEGER, portInfoFlowCtrl INTEGER, portInfoLink INTEGER, portInfoPhyIfDescr DisplayString, portInfoPhyIfType INTEGER, portInfoPhyIfMtu Integer32, portInfoPhyIfPhysAddress PhysAddress, portInfoPhyIfOperStatus INTEGER, portInfoPhyIfLastChange TimeTicks, portInfoLearning INTEGER, portInfoBpduGuard INTEGER, portInfoPvid Unsigned32, portInfoVlanTag INTEGER ,portInfoErrDisableRecovery INTEGER ,portInfoErrDisableTimeLeft INTEGER ,portInfoExtGuard INTEGER ,portInfoLFDState INTEGER } portInfoIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port index." ::= { portInfoTableEntry 1 } portInfoSpeed OBJECT-TYPE SYNTAX INTEGER { mbs10(2), mbs100(3), mbs1000(4), any(5) , mbs10000(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational speed of the port." ::= { portInfoTableEntry 2 } portInfoMode OBJECT-TYPE SYNTAX INTEGER { full-duplex(2), half-duplex(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational mode of the port." ::= { portInfoTableEntry 3 } portInfoFlowCtrl OBJECT-TYPE SYNTAX INTEGER { transmit(2), receive(3), both(4), none(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational flow control of the port." ::= { portInfoTableEntry 4 } portInfoLink OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), disabled(3), inoperative(4), -- unrecognized PCI device errdisabled(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational link status of the port." ::= { portInfoTableEntry 5 } portInfoPhyIfDescr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface." ::= { portInfoTableEntry 6 } portInfoPhyIfType OBJECT-TYPE SYNTAX INTEGER { other(1), -- none of the following regular1822(2), hdh1822(3), ddn-x25(4), rfc877-x25(5), ethernet-csmacd(6), iso88023-csmacd(7), iso88024-tokenBus(8), iso88025-tokenRing(9), iso88026-man(10), starLan(11), proteon-10Mbit(12), proteon-80Mbit(13), hyperchannel(14), fddi(15), lapb(16), sdlc(17), ds1(18), -- T-1 e1(19), -- european equiv. of T-1 basicISDN(20), primaryISDN(21), -- proprietary serial propPointToPointSerial(22), ppp(23), softwareLoopback(24), eon(25), -- CLNP over IP [11] ethernet-3Mbit(26), nsip(27), -- XNS over IP slip(28), -- generic SLIP ultra(29), -- ULTRA technologies ds3(30), -- T-3 sip(31), -- SMDS frame-relay(32) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack." ::= { portInfoTableEntry 7 } portInfoPhyIfMtu OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface." ::= { portInfoTableEntry 8 } portInfoPhyIfPhysAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length." ::= { portInfoTableEntry 9 } portInfoPhyIfOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), -- ready to pass packets down(2), testing(3) -- in some test mode } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed." ::= { portInfoTableEntry 10 } portInfoPhyIfLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value." ::= { portInfoTableEntry 11 } portInfoLearning OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port L2 (FDB) Learning state." ::= { portInfoTableEntry 18 } portInfoBpduGuard OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operational status of BPDU Guard on the port." ::= { portInfoTableEntry 20 } portInfoPvid OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the operational port vlan-id of the port. Typically, the value of this object is the same as the value of the agPortCurCfgPVID object. But if, for example, 802.1x is enabled on the port and the port is assigned a vlan-id via 802.1x, this port will be moved to the assigned vlan even when the port is configured with a different PVID." ::= { portInfoTableEntry 21} portInfoVlanTag OBJECT-TYPE SYNTAX INTEGER { untagged(0), tagged(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the operational VLAN tag state of the port. Typically, the value of this object is the same as the value of the agPortCurCfgVlanTag objec. But if, for example, 802.1x is enabled on the port and if the port is assigned a vlan via 802.1x, the port will be operationally untagged even when the port is configured to be tagged." ::= { portInfoTableEntry 22} portInfoErrDisableRecovery OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the system will automatically re-enable an error-disabled port after the time interval indicated by agCurCfgErrDisableTimeout has elapsed. A port is in error-disabled state when it has been operationally disabled by the system due to an error condition. The value of this object is 'enable' if the values of both the global agCurCfgErrDisableRecovery object and the port's agPortCurCfgErrDisableRecovery object are 'enable'." ::= { portInfoTableEntry 23 } portInfoErrDisableTimeLeft OBJECT-TYPE SYNTAX INTEGER (0 .. 86400) MAX-ACCESS read-only STATUS current DESCRIPTION "If the portInfoErrDisableRecovery object has a value of 'enable' and the portInfoLink object has a value of 'errdisabled', the value of this object indicates the remaining time, in seconds, before the system automatically re-enables this port." ::= { portInfoTableEntry 24 } portInfoExtGuard OBJECT-TYPE SYNTAX INTEGER { loop(1), root(2), global-loop(3), no-guard(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "The operational status of STP Loop/Root Guard on the port." ::= { portInfoTableEntry 25 } portInfoLFDState OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the port is error-disabled due to excessive link flaps. The value of this object is 'yes' if the port is error-disabled due to excessive link flaps, otherwise the value is 'no'." ::= { portInfoTableEntry 26 } -- Agent System Group -- This group of objects take effect on the 'SET' request. -- There is no need to 'apply' or 'save'. agApplyConfiguration OBJECT-TYPE SYNTAX INTEGER { other(1), apply(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to apply the changes made to configuration of the switch. By setting the value to apply(2), all the changes made since the last apply are written to the new configuration block. other(1) is returned when this object ie read. " ::= { agSystem 2 } agSavePending OBJECT-TYPE SYNTAX INTEGER { saveNeeded(1), noSaveNeeded(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object, when read, gives the user information whether an save action is needed and that the configuration has been applied but not saved to the flash." ::= { agSystem 3 } agSaveConfiguration OBJECT-TYPE SYNTAX INTEGER { ok(1), saveActive(2), notSaveActive(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to write current configuration to nonvolatile storage. When issued with the saveActive, the active configuration in flash is saved to backup in flash and then the new configuration is saved to the active configuration in flash. When issued with notSaveActive, the active configuration is NOT saved to the flash and the active configuration is overwritten with the new configuration. ok(1) is returned always when read." ::= { agSystem 4 } agRevert OBJECT-TYPE SYNTAX INTEGER { other(1), revert(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to revert the unapplied changes made to the switch. By setting the value to revert(2), all the unapplied changes will be reverted. This action will copy the current_config to the new configuration block. other(1) is returned when this object is read. " ::= { agSystem 5 } agReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reboot the agent. other(1) is returned always when read." ::= { agSystem 7 } agConfigForNxtReset OBJECT-TYPE SYNTAX INTEGER { active(2), backup(3), default(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The configuration information to be loaded from at next reset. The following values are writable: active(2)...active configuration block backup(3)...backup configuration block default(4)..default configuration block" ::= { agSystem 8 } agImageForNxtReset OBJECT-TYPE SYNTAX INTEGER { image1(2), image2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The software image to be booted from at next reset. The following values are writable: image1(2)...image 1 image2(3)...image 2" ::= { agSystem 9 } agSoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the software image that is currently running on the system in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not available." ::= { agSystem 10 } agBootVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the boot code in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available." ::= { agSystem 11 } agImage1Ver OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the software image stored in image 1 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available or there is no valid software image." ::= { agSystem 12 } agImage2Ver OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the software image stored in image 2 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available or there is no valid software image." ::= { agSystem 13 } agRtcDate OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "The date on the real time clock in the form of 'mm/dd/yy'. A zero length string is returned if date is not available." ::= { agSystem 14 } agRtcTime OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time on the real time clock in the form of 'hh:mm:ss'. A zero length string is returned if time is not available." ::= { agSystem 15 } agLastSetErrorReason OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The error reason of the last SET failure." ::= { agSystem 16 } agCurCfgHttpServerPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP port number that the HTTP server is listening to in the current configuration block." ::= { agSystem 17 } agNewCfgHttpServerPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP port number that the HTTP server is listening to in the new configuration block." ::= { agSystem 18 } agCurCfgLoginBanner OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "The user defined login banner." ::= { agSystem 19 } agNewCfgLoginBanner OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-write STATUS current DESCRIPTION "The user defined login banner." ::= { agSystem 20 } agCurCfgLoginNotice OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "The user defined login notice." ::= { agSystem 78 } agNewCfgLoginNotice OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-write STATUS current DESCRIPTION "The user defined login notice." ::= { agSystem 79 } agCurCfgConsole OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable console output of syslog messages." ::= { agSystem 23 } agNewCfgConsole OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable console output of syslog messages." ::= { agSystem 24 } agSlotNumber OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the slot in which this switch is installed. If the agent implementing this MIB is not a blade in a chassis this value has no meaning." ::= { agSystem 31 } agCurCfgSnmpTimeout OBJECT-TYPE SYNTAX INTEGER (1..30) MAX-ACCESS read-only STATUS current DESCRIPTION "Once SNMP operations like agApplyConfig, agDiffState and agDumpState, which use the state machine are done the resources used by these operations need to be freed by setting the state back to 'idle' so others can issue the commands via SNMP. agSnmpTimeout indicates the number of minutes before the resources are freed and the state set back to 'idle' if this operation is not performed by the user." ::= { agSystem 32 } agNewCfgSnmpTimeout OBJECT-TYPE SYNTAX INTEGER (1..30) MAX-ACCESS read-write STATUS current DESCRIPTION "Once SNMP operations like agApplyConfig, agDiffState and agDumpState, which use the state machine are done the resources used by these operations need to be freed by setting the state back to 'idle' so others can issue the commands via SNMP. agSnmpTimeout indicates the number of minutes before the resources are freed and the state set back to 'idle' if this operation is not performed by the user." ::= { agSystem 33 } agCurCfgTelnetServerPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP port number that the telnet server listens for telnet sessions." ::= { agSystem 34 } agNewCfgTelnetServerPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP port number that the telnet server listens for telnet sessions." ::= { agSystem 35 } agClearFlashDump OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to clear the FLASH dump. ok(1) is returned when this object is read. " ::= { agSystem 36 } agCurCfgTrapSrcIf OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The SNMP trap source interface number." ::= { agSystem 39 } agNewCfgTrapSrcIf OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The SNMP trap source interface number." ::= { agSystem 40 } agCurCfgHttpsServerPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP port number that the HTTPS server is listening to in the current configuration block." ::= { agSystem 49 } agNewCfgHttpsServerPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP port number that the HTTPS server is listening to in the new configuration block." ::= { agSystem 50 } agCurCfgTftpServerPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP port number that the TFTP server is listening to in the current configuration block." ::= { agSystem 51 } agNewCfgTftpServerPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP port number that the TFTP server is listening to in the new configuration block." ::= { agSystem 52 } agRackId OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The rack unique identifier." ::= { agSystem 53 } agChassis OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "Chassis serial number." ::= { agSystem 54 } agCurTimeZone OBJECT-TYPE SYNTAX INTEGER { none(0), africa-Algeria(1), africa-Angola(2), africa-Benin(3), africa-Botswana(4), africa-Burkina-Faso(5), africa-Burundi(6), africa-Cameroon(7), africa-Central-African-Rep(8), africa-Chad(9), africa-Congo-WestDemRepCongo(10), africa-Congo-EastDemRepCongo(11), africa-Congo-Rep(12), africa-Cote-dIvoire(13), africa-Djibouti(14), africa-Egypt(15), africa-Equatorial-Guinea(16), africa-Eritrea(17), africa-Ethiopia(18), africa-Gabon(19), africa-Gambia(20), africa-Ghana(21), africa-Guinea(22), africa-Guinea-Bissau(23), africa-Kenya(24), africa-Lesotho(25), africa-Liberia(26), africa-Libya(27), africa-Malawi(28), africa-Mali-SouthWestMali(29), africa-Mali-NorthEastMali(30), africa-Mauritania(31), africa-Morocco(32), africa-Mozambique(33), africa-Namibia(34), africa-Niger(35), africa-Nigeria(36), africa-Rwanda(37), africa-SaoTome-And-Principe(38), africa-Senegal(39), africa-SierraLeone(40), africa-Somalia(41), africa-SouthAfrica(42), africa-Spain-Mainland(43), africa-Spain-CeutaMelilla(44), africa-Spain-CanaryIslands(45), africa-Sudan(46), africa-Swaziland(47), africa-Tanzania(48), africa-Togo(49), africa-Tunisia(50), africa-Uganda(51), africa-Western-Sahara(52), africa-Zambia(53), africa-Zimbabwe(54), americas-Anguilla(55), americas-Antigua-Barbuda(56), americas-Argentina-EArgentina(57), americas-Argentina-MostLocations(58), americas-Argentina-Jujuy(59), americas-Argentina-Catamarca(60), americas-Argentina-Mendoza(61), americas-Aruba(62), americas-Bahamas(63), americas-Barbados(64), americas-Belize(65), americas-Bolivia(66), americas-Brazil-AtlanticIslands(67), americas-Brazil-AmapaEPara(68), americas-Brazil-NEBrazil(69), americas-Brazil-Pernambuco(70), americas-Brazil-Tocantins(71), americas-Brazil-AlagoasSergipe(72), americas-Brazil-SSEBrazil(73), americas-Brazil-MatoGrossoDoSul(74), americas-Brazil-WParaRondonia(75), americas-Brazil-Roraima(76), americas-Brazil-EAmazonas(77), americas-Brazil-WAmazonas(78), americas-Brazil-Acre(79), americas-Canada-NewfoundlandIsland(80), americas-Canada-AtlanTime-NovaScotia(81), americas-Canada-AtlanTime-ELabrador(82), americas-Canada-EastTime-OntarioMostlocation(83), americas-Canada-EastTime-ThunderBay(84), americas-Canada-EastStdTime-PangnirtungNunavut(85), americas-Canada-EastStdTime-EastNunavut(86), americas-Canada-EastStdTime-CenNunavut(87), americas-Canada-CenTime-ManitobaWestOntario(88), americas-Canada-CenTime-RainyRiver(89), americas-Canada-CenTime-WestNunavut(90), americas-Canada-CenStdTime-SaskatchewanMostlocation(91), americas-Canada-CenStdTime-SaskatchewanMidwest(92), americas-Canada-MountTime-AlbertaEastBritishColumbia(93), americas-Canada-MountTime-CentralNorthwestTerritories(94), americas-Canada-MountTime-WestNorthwestTerritories(95), americas-Canada-MountStdTime-DawsonCrkStJohnBritColumbia(96), americas-Canada-PacificTime-WestBritishColumbia(97), americas-Canada-PacificTime-SouthYukon(98), americas-Canada-PacificTime-NorthYukon(99), americas-CaymanIslands(100), americas-Chile-MostLocation(101), americas-Chile-EasterIsland(102), americas-Colombia(103), americas-CostaRica(104), americas-Cuba(105), americas-Dominica(106), americas-DominicanRepublic (107), americas-Ecuador(108), americas-ElSalvado(109), americas-FrenchGuiana(110), americas-Greenland-MostLocation(111), americas-Greenland-EastCoastNorthScoresbysund(112), americas-Greenland-ScoresbysundIttoqqortoormiit(113), americas-Greenland-ThulePituffik(114), americas-Grenada(115), americas-Guadeloupe(116), americas-Guatemala(117), americas-Guyana(118), americas-Haiti(119), americas-Honduras(120), americas-Jamaica(121), americas-Martinique(122), americas-Mexico-CentTime-Mostlocations(123), americas-Mexico-CentTime-QuintanaRoo(124), americas-Mexico-CentTime-CampecheYucatan(125), americas-Mexico-CentTime-CoahuilaDurNuevoLeonTam(126), americas-Mexico-MountTime-SBajaNayaritSinaloa(127), americas-Mexico-MountTime-Chihuahua(128), americas-Mexico-MountStdTime-Sonora(129), americas-Mexico-PacificTime(130), americas-Montserrat(131), americas-NetherlandsAntilles(132), americas-Nicaragua(133), americas-Panama(134), americas-Paraguay(135), americas-Peru(136), americas-PuertoRico(137), americas-StKittsAndNevis(138), americas-StLucia(139), americas-StPierreAndMiquelon(140), americas-StVincent(141), americas-Suriname(142), americas-TrinidadAndTobago(143), americas-TurksAndCaicosIs(144), americas-USA-EastTime(145), americas-USA-EastTime-MichiganMostLocation(146), americas-USA-EastTime-KentuckyLouisvilleArea(147), americas-USA-EastTime-KentuckyWayneCounty(148), americas-USA-EastStdTime-IndianaMostLocations(149), americas-USA-EastStdTime-IndianaCrawfordCounty(150), americas-USA-EastStdTime-IndianaStarkeCounty(151), americas-USA-EastStdTime-IndianaSwitzerlandCounty(152), americas-USA-CentTime(153), americas-USA-CentTime-MichiganWisconsinborder(154), americas-USA-CentTime-NorthDakotaOliverCounty(155), americas-USA-MountTime(156), americas-USA-MountTime-SouthIdahoAndEastOregon(157), americas-USA-MountTime-Navajo(158), americas-USA-MountStdTime-Arizona(159), americas-USA-PacificTime(160), americas-USA-AlaskaTime(161), americas-USA-AlaskaTime-AlaskaPanhandle(162), americas-USA-AlaskaTime-AlaskaPanhandleNeck(163), americas-USA-AlaskaTime-WestAlaska(164), americas-USA-AleutianIslands(165), americas-USA-Hawaii(166), americas-Uruguay(167), americas-Venezuela(168), americas-VirginIslands-UK(169), americas-VirginIslands-US(170), antarctica-McMurdoStationRossIsland(171), antarctica-Amundsen-ScottStationSouthPole(172), antarctica-PalmerStationAnversIsland(173), antarctica-MawsonStationHolmeBay(174), antarctica-DavisStationVestfoldHills(175), antarctica-CaseyStationBaileyPeninsula(176), antarctica-VostokStationSMagneticPole(177), antarctica-Dumont-dUrvilleBaseTerreAdelie(178), antarctica-SyowaStationEOngulI(179), arcticOcean-Svalbard(180), arcticOcean-JanMayen(181), asia-Afghanistan(182), asia-Armenia(183), asia-Azerbaijan(184), asia-Bahrain(185), asia-Bangladesh(186), asia-Bhutan(187), asia-Brunei(188), asia-Cambodia(189), asia-China-EastChinaBeijingGuangdongShanghai(190), asia-China-Heilongjiang(191), asia-China-CentralChinaGansuGuizhouSichuanYunnan(192), asia-China-TibetmostofXinjiangUyghur(193), asia-China-SouthwestXinjiangUyghur(194), asia-Cyprus(195), asia-EastTimor(196), asia-Georgia(197), asia-HongKong(198), asia-India(199), asia-Indonesia-JavaAndSumatra(200), asia-Indonesia-WestCentralBorneo(201), asia-Indonesia-ESBorneoCelebesBaliNusaTengaWTimor(202), asia-Indonesia-IrianJayaAndMoluccas(203), asia-Iran(204), asia-Iraq(205), asia-Israel(206), asia-Japan(207), asia-Jordan(208), asia-Kazakhstan-MostLocations(209), asia-Kazakhstan-QyzylordaKyzylorda(210), asia-Kazakhstan-Aqtobe(211), asia-Kazakhstan-AtyrauMangghystau(212), asia-Kazakhstan-WestKazakhstan(213), asia-Korea-North(214), asia-Korea-South(215), asia-Kuwait(216), asia-Kyrgyzstan(217), asia-Laos(218), asia-Lebanon(219), asia-Macau(220), asia-Malaysia-PeninsularMalaysia(221), asia-Malaysia-SabahSarawak(222), asia-Mongolia-MostLocations(223), asia-Mongolia-BayanOlgiyGoviAltaiHovdUvsZavkhan(224), asia-Mongolia-DornodSukhbaatar(225), asia-Myanmar(226), asia-Nepal(227), asia-Oman(228), asia-Pakistan(229), asia-Palestine(230), asia-Philippines(231), asia-Qatar(232), asia-Russia-Moscow-01Kaliningrad(233), asia-Russia-Moscow00WestRussia(234), asia-Russia-Moscow01CaspianSea(235), asia-Russia-Moscow02Urals(236), asia-Russia-Moscow03WestSiberia(237), asia-Russia-Moscow03Novosibirsk(238), asia-Russia-Moscow04YeniseiRiver(239), asia-Russia-Moscow05LakeBaikal(240), asia-Russia-Moscow06LenaRiver(241), asia-Russia-Moscow07AmurRiver(242), asia-Russia-Moscow07SakhalinIsland(243), asia-Russia-Moscow08Magadan(244), asia-Russia-Moscow09Kamchatka(245), asia-Russia-Moscow10BeringSea(246), asia-SaudiArabia(247), asia-Singapore(248), asia-SriLanka(249), asia-Syria(250), asia-Taiwan(251), asia-Tajikistan(252), asia-Thailand(253), asia-Turkmenistan(254), asia-UnitedArabEmirates(255), asia-Uzbekistan-WestUzbekistan(256), asia-Uzbekistan-EastUzbekistan(257), asia-Vietnam(258), asia-Yemen(259), atlanticOcean-Bermuda(260), atlanticOcean-CapeVerde(261), atlanticOcean-FaeroeIslands(262), atlanticOcean-FalklandIslands(263), atlanticOcean-Iceland(264), atlanticOcean-Portugal-Mainland(265), atlanticOcean-Portugal-MadeiraIslands(266), atlanticOcean-Portugal-Azores(267), atlanticOcean-SouthGeorgia-SouthSandwichIslands(268), atlanticOcean-Spain-Mainland(269), atlanticOcean-Spain-CeutaMelilla(270), atlanticOcean-Spain-CanaryIslands(271), atlanticOcean-StHelena(272), atlanticOcean-Svalbard-JanMayen(273), australia-LordHoweIsland(274), australia-Tasmania(275), australia-Victoria(276), australia-NewSouthWales-MostLocations(277), australia-NewSouthWales-Yancowinna(278), australia-Queensland-MostLocations(279), australia-Queensland-HolidayIslands(280), australia-SouthAustralia(281), australia-NorthernTerritory(282), australia-WesternAustralia(283), europe-Albania(284), europe-Andorra(285), europe-Austria(286), europe-Belarus(287), europe-Belgium(288), europe-BosniaHerzegovina(289), europe-Britain-UKGreatBritain(290), europe-Britain-UKNorthernIreland(291), europe-Bulgaria(292), europe-Croatia(293), europe-CzechRepublic(294), europe-Denmark(295), europe-Estonia(296), europe-Finland(297), europe-France(298), europe-Germany(299), europe-Gibraltar(300), europe-Greece(301), europe-Hungary(302), europe-Ireland(303), europe-Italy(304), europe-Latvia(305), europe-Liechtenstein(306), europe-Lithuania(307), europe-Luxembourg(308), europe-Macedonia(309), europe-Malta(310), europe-Moldova(311), europe-Monaco(312), europe-Montenegro(421), europe-Netherlands(313), europe-Norway(314), europe-Poland(315), europe-Portugal-Mainland(316), europe-Portugal-MadeiraIslands(317), europe-Portugal-Azores(318), europe-Romania(319), europe-Russia-Moscow-01Kaliningrad(320), europe-Russia-Moscow00WestRussia(321), europe-Russia-Moscow01CaspianSea(322), europe-Russia-Moscow02Urals(323), europe-Russia-Moscow03WestSiberia(324), europe-Russia-Moscow03Novosibirsk(325), europe-Russia-Moscow04YeniseiRiver(326), europe-Russia-Moscow05LakeBaikal(327), europe-Russia-Moscow06LenaRiver(328), europe-Russia-Moscow07AmurRiver(329), europe-Russia-Moscow07SakhalinIsland(330), europe-Russia-Moscow08Magadan(331), europe-Russia-Moscow09Kamchatka(332), europe-Russia-Moscow10BeringSea(333), europe-SanMarino(334), europe-Serbia(348), europe-Slovakia(335), europe-Slovenia(336), europe-Spain-Mainland(337), europe-Spain-CeutaAndMelilla(338), europe-Spain-CanaryIslands(339), europe-Sweden(340), europe-Switzerland(341), europe-Turkey(342), europe-Ukraine-MostLocations(343), europe-Ukraine-Ruthenia(344), europe-Ukraine-Zaporozhye-ELugansk(345), europe-Ukraine-CentralCrimea(346), europe-VaticanCity(347), indianOcean-BritishIndianOceanTerritory(349), indianOcean-ChristmasIsland(350), indianOcean-CocosOrKeelingIslands(351), indianOcean-Comoros(352), indianOcean-FrenchSouthernAndAntarcticLands(353), indianOcean-Madagascar(354), indianOcean-Maldives(355), indianOcean-Mauritius(356), indianOcean-Mayotte(357), indianOcean-Reunion(358), indianOcean-Seychelles(359), pacificOcean-Chile-MostLocations(360), pacificOcean-Chile-EasterIslandSalayGomez(361), pacificOcean-CookIslands(362), pacificOcean-Ecuador(363), pacificOcean-Fiji(364), pacificOcean-FrenchPolynesia-SocietyIslands(365), pacificOcean-FrenchPolynesia-MarquesasIslands(366), pacificOcean-FrenchPolynesia-GambierIslands(367), pacificOcean-Guam(368), pacificOcean-Kiribati-GilbertIslands(369), pacificOcean-Kiribati-PhoenixIslands(370), pacificOcean-Kiribati-LineIslands(371), pacificOcean-MarshallIslands-MostLocations(372), pacificOcean-MarshallIslands-Kwajalein(373), pacificOcean-Micronesia-Yap(374), pacificOcean-Micronesia-TrukOrChuuk(375), pacificOcean-Micronesia-PonapeOrPohnpei(376), pacificOcean-Micronesia-Kosrae(377), pacificOcean-Nauru(378), pacificOcean-NewCaledonia(379), pacificOcean-NewZealand-MostLocations(380), pacificOcean-NewZealand-ChathamIslands(381), pacificOcean-Niue(382), pacificOcean-NorfolkIsland(383), pacificOcean-NorthernMarianaIslands(384), pacificOcean-Palau(385), pacificOcean-PapuaNewGuinea(386), pacificOcean-Pitcairn(387), pacificOcean-SamoaAmerican(388), pacificOcean-SamoaWestern(389), pacificOcean-SolomonIslands(390), pacificOcean-Tokelau(391), pacificOcean-Tonga(392), pacificOcean-Tuvalu(393), pacificOceanUSA-EastTime(394), pacificOceanUSA-EastTime-MichiganMostLocations(395), pacificOceanUSA-EastTime-KentuckyLouisvilleArea(396), pacificOceanUSA-EastTime-KentuckyWayneCounty(397), pacificOceanUSA-EastStdTime-IndianaMostLocations(398), pacificOceanUSA-EastStdTime-IndianaCrawfordCounty(399), pacificOceanUSA-EastStdTime-IndianaStarkeCounty(400), pacificOceanUSA-EastStdTime-IndianaSwitzerlandCounty(401), pacificOceanUSA-CentTime(402), pacificOceanUSA-CentTime-MichiganWisconsinborder(403), pacificOceanUSA-CentTime-NorthDakotaOliverCounty(404), pacificOceanUSA-MountTime(405), pacificOceanUSA-MountTime-SouthIdahoAndEastOregon(406), pacificOceanUSA-MountTime-Navajo(407), pacificOceanUSA-MountStdTime-Arizona(408), pacificOceanUSA-PacificTime(409), pacificOceanUSA-AlaskaTime(410), pacificOceanUSA-AlaskaTime-AlaskaPanhandle(411), pacificOceanUSA-AlaskaTime-AlaskaPanhandleNeck(412), pacificOceanUSA-AlaskaTime-WestAlaska(413), pacificOceanUSA-AleutianIslands(414), pacificOceanUSA-Hawaii(415), pacificOcean-USMinorOutlyingIslands-JohnstonAtoll(416), pacificOcean-USMinorOutlyingIslands-MidwayIslands(417), pacificOcean-USMinorOutlyingIslands-WakeIsland(418), pacificOcean-Vanuatu(419), pacificOcean-WallisAndFutuna(420) } MAX-ACCESS read-only STATUS current DESCRIPTION "The time zone. Note: Locations are alphabetically ordered and the corresponding code is not reflected in CLI." ::= { agSystem 55 } agNewTimeZone OBJECT-TYPE SYNTAX INTEGER { none(0), africa-Algeria(1), africa-Angola(2), africa-Benin(3), africa-Botswana(4), africa-Burkina-Faso(5), africa-Burundi(6), africa-Cameroon(7), africa-Central-African-Rep(8), africa-Chad(9), africa-Congo-WestDemRepCongo(10), africa-Congo-EastDemRepCongo(11), africa-Congo-Rep(12), africa-Cote-dIvoire(13), africa-Djibouti(14), africa-Egypt(15), africa-Equatorial-Guinea(16), africa-Eritrea(17), africa-Ethiopia(18), africa-Gabon(19), africa-Gambia(20), africa-Ghana(21), africa-Guinea(22), africa-Guinea-Bissau(23), africa-Kenya(24), africa-Lesotho(25), africa-Liberia(26), africa-Libya(27), africa-Malawi(28), africa-Mali-SouthWestMali(29), africa-Mali-NorthEastMali(30), africa-Mauritania(31), africa-Morocco(32), africa-Mozambique(33), africa-Namibia(34), africa-Niger(35), africa-Nigeria(36), africa-Rwanda(37), africa-SaoTome-And-Principe(38), africa-Senegal(39), africa-SierraLeone(40), africa-Somalia(41), africa-SouthAfrica(42), africa-Spain-Mainland(43), africa-Spain-CeutaMelilla(44), africa-Spain-CanaryIslands(45), africa-Sudan(46), africa-Swaziland(47), africa-Tanzania(48), africa-Togo(49), africa-Tunisia(50), africa-Uganda(51), africa-Western-Sahara(52), africa-Zambia(53), africa-Zimbabwe(54), americas-Anguilla(55), americas-Antigua-Barbuda(56), americas-Argentina-EArgentina(57), americas-Argentina-MostLocations(58), americas-Argentina-Jujuy(59), americas-Argentina-Catamarca(60), americas-Argentina-Mendoza(61), americas-Aruba(62), americas-Bahamas(63), americas-Barbados(64), americas-Belize(65), americas-Bolivia(66), americas-Brazil-AtlanticIslands(67), americas-Brazil-AmapaEPara(68), americas-Brazil-NEBrazil(69), americas-Brazil-Pernambuco(70), americas-Brazil-Tocantins(71), americas-Brazil-AlagoasSergipe(72), americas-Brazil-SSEBrazil(73), americas-Brazil-MatoGrossoDoSul(74), americas-Brazil-WParaRondonia(75), americas-Brazil-Roraima(76), americas-Brazil-EAmazonas(77), americas-Brazil-WAmazonas(78), americas-Brazil-Acre(79), americas-Canada-NewfoundlandIsland(80), americas-Canada-AtlanTime-NovaScotia(81), americas-Canada-AtlanTime-ELabrador(82), americas-Canada-EastTime-OntarioMostlocation(83), americas-Canada-EastTime-ThunderBay(84), americas-Canada-EastStdTime-PangnirtungNunavut(85), americas-Canada-EastStdTime-EastNunavut(86), americas-Canada-EastStdTime-CenNunavut(87), americas-Canada-CenTime-ManitobaWestOntario(88), americas-Canada-CenTime-RainyRiver(89), americas-Canada-CenTime-WestNunavut(90), americas-Canada-CenStdTime-SaskatchewanMostlocation(91), americas-Canada-CenStdTime-SaskatchewanMidwest(92), americas-Canada-MountTime-AlbertaEastBritishColumbia(93), americas-Canada-MountTime-CentralNorthwestTerritories(94), americas-Canada-MountTime-WestNorthwestTerritories(95), americas-Canada-MountStdTime-DawsonCrkStJohnBritColumbia(96), americas-Canada-PacificTime-WestBritishColumbia(97), americas-Canada-PacificTime-SouthYukon(98), americas-Canada-PacificTime-NorthYukon(99), americas-CaymanIslands(100), americas-Chile-MostLocation(101), americas-Chile-EasterIsland(102), americas-Colombia(103), americas-CostaRica(104), americas-Cuba(105), americas-Dominica(106), americas-DominicanRepublic (107), americas-Ecuador(108), americas-ElSalvado(109), americas-FrenchGuiana(110), americas-Greenland-MostLocation(111), americas-Greenland-EastCoastNorthScoresbysund(112), americas-Greenland-ScoresbysundIttoqqortoormiit(113), americas-Greenland-ThulePituffik(114), americas-Grenada(115), americas-Guadeloupe(116), americas-Guatemala(117), americas-Guyana(118), americas-Haiti(119), americas-Honduras(120), americas-Jamaica(121), americas-Martinique(122), americas-Mexico-CentTime-Mostlocations(123), americas-Mexico-CentTime-QuintanaRoo(124), americas-Mexico-CentTime-CampecheYucatan(125), americas-Mexico-CentTime-CoahuilaDurNuevoLeonTam(126), americas-Mexico-MountTime-SBajaNayaritSinaloa(127), americas-Mexico-MountTime-Chihuahua(128), americas-Mexico-MountStdTime-Sonora(129), americas-Mexico-PacificTime(130), americas-Montserrat(131), americas-NetherlandsAntilles(132), americas-Nicaragua(133), americas-Panama(134), americas-Paraguay(135), americas-Peru(136), americas-PuertoRico(137), americas-StKittsAndNevis(138), americas-StLucia(139), americas-StPierreAndMiquelon(140), americas-StVincent(141), americas-Suriname(142), americas-TrinidadAndTobago(143), americas-TurksAndCaicosIs(144), americas-USA-EastTime(145), americas-USA-EastTime-MichiganMostLocation(146), americas-USA-EastTime-KentuckyLouisvilleArea(147), americas-USA-EastTime-KentuckyWayneCounty(148), americas-USA-EastStdTime-IndianaMostLocations(149), americas-USA-EastStdTime-IndianaCrawfordCounty(150), americas-USA-EastStdTime-IndianaStarkeCounty(151), americas-USA-EastStdTime-IndianaSwitzerlandCounty(152), americas-USA-CentTime(153), americas-USA-CentTime-MichiganWisconsinborder(154), americas-USA-CentTime-NorthDakotaOliverCounty(155), americas-USA-MountTime(156), americas-USA-MountTime-SouthIdahoAndEastOregon(157), americas-USA-MountTime-Navajo(158), americas-USA-MountStdTime-Arizona(159), americas-USA-PacificTime(160), americas-USA-AlaskaTime(161), americas-USA-AlaskaTime-AlaskaPanhandle(162), americas-USA-AlaskaTime-AlaskaPanhandleNeck(163), americas-USA-AlaskaTime-WestAlaska(164), americas-USA-AleutianIslands(165), americas-USA-Hawaii(166), americas-Uruguay(167), americas-Venezuela(168), americas-VirginIslands-UK(169), americas-VirginIslands-US(170), antarctica-McMurdoStationRossIsland(171), antarctica-Amundsen-ScottStationSouthPole(172), antarctica-PalmerStationAnversIsland(173), antarctica-MawsonStationHolmeBay(174), antarctica-DavisStationVestfoldHills(175), antarctica-CaseyStationBaileyPeninsula(176), antarctica-VostokStationSMagneticPole(177), antarctica-Dumont-dUrvilleBaseTerreAdelie(178), antarctica-SyowaStationEOngulI(179), arcticOcean-Svalbard(180), arcticOcean-JanMayen(181), asia-Afghanistan(182), asia-Armenia(183), asia-Azerbaijan(184), asia-Bahrain(185), asia-Bangladesh(186), asia-Bhutan(187), asia-Brunei(188), asia-Cambodia(189), asia-China-EastChinaBeijingGuangdongShanghai(190), asia-China-Heilongjiang(191), asia-China-CentralChinaGansuGuizhouSichuanYunnan(192), asia-China-TibetmostofXinjiangUyghur(193), asia-China-SouthwestXinjiangUyghur(194), asia-Cyprus(195), asia-EastTimor(196), asia-Georgia(197), asia-HongKong(198), asia-India(199), asia-Indonesia-JavaAndSumatra(200), asia-Indonesia-WestCentralBorneo(201), asia-Indonesia-ESBorneoCelebesBaliNusaTengaWTimor(202), asia-Indonesia-IrianJayaAndMoluccas(203), asia-Iran(204), asia-Iraq(205), asia-Israel(206), asia-Japan(207), asia-Jordan(208), asia-Kazakhstan-MostLocations(209), asia-Kazakhstan-QyzylordaKyzylorda(210), asia-Kazakhstan-Aqtobe(211), asia-Kazakhstan-AtyrauMangghystau(212), asia-Kazakhstan-WestKazakhstan(213), asia-Korea-North(214), asia-Korea-South(215), asia-Kuwait(216), asia-Kyrgyzstan(217), asia-Laos(218), asia-Lebanon(219), asia-Macau(220), asia-Malaysia-PeninsularMalaysia(221), asia-Malaysia-SabahSarawak(222), asia-Mongolia-MostLocations(223), asia-Mongolia-BayanOlgiyGoviAltaiHovdUvsZavkhan(224), asia-Mongolia-DornodSukhbaatar(225), asia-Myanmar(226), asia-Nepal(227), asia-Oman(228), asia-Pakistan(229), asia-Palestine(230), asia-Philippines(231), asia-Qatar(232), asia-Russia-Moscow-01Kaliningrad(233), asia-Russia-Moscow00WestRussia(234), asia-Russia-Moscow01CaspianSea(235), asia-Russia-Moscow02Urals(236), asia-Russia-Moscow03WestSiberia(237), asia-Russia-Moscow03Novosibirsk(238), asia-Russia-Moscow04YeniseiRiver(239), asia-Russia-Moscow05LakeBaikal(240), asia-Russia-Moscow06LenaRiver(241), asia-Russia-Moscow07AmurRiver(242), asia-Russia-Moscow07SakhalinIsland(243), asia-Russia-Moscow08Magadan(244), asia-Russia-Moscow09Kamchatka(245), asia-Russia-Moscow10BeringSea(246), asia-SaudiArabia(247), asia-Singapore(248), asia-SriLanka(249), asia-Syria(250), asia-Taiwan(251), asia-Tajikistan(252), asia-Thailand(253), asia-Turkmenistan(254), asia-UnitedArabEmirates(255), asia-Uzbekistan-WestUzbekistan(256), asia-Uzbekistan-EastUzbekistan(257), asia-Vietnam(258), asia-Yemen(259), atlanticOcean-Bermuda(260), atlanticOcean-CapeVerde(261), atlanticOcean-FaeroeIslands(262), atlanticOcean-FalklandIslands(263), atlanticOcean-Iceland(264), atlanticOcean-Portugal-Mainland(265), atlanticOcean-Portugal-MadeiraIslands(266), atlanticOcean-Portugal-Azores(267), atlanticOcean-SouthGeorgia-SouthSandwichIslands(268), atlanticOcean-Spain-Mainland(269), atlanticOcean-Spain-CeutaMelilla(270), atlanticOcean-Spain-CanaryIslands(271), atlanticOcean-StHelena(272), atlanticOcean-Svalbard-JanMayen(273), australia-LordHoweIsland(274), australia-Tasmania(275), australia-Victoria(276), australia-NewSouthWales-MostLocations(277), australia-NewSouthWales-Yancowinna(278), australia-Queensland-MostLocations(279), australia-Queensland-HolidayIslands(280), australia-SouthAustralia(281), australia-NorthernTerritory(282), australia-WesternAustralia(283), europe-Albania(284), europe-Andorra(285), europe-Austria(286), europe-Belarus(287), europe-Belgium(288), europe-BosniaHerzegovina(289), europe-Britain-UKGreatBritain(290), europe-Britain-UKNorthernIreland(291), europe-Bulgaria(292), europe-Croatia(293), europe-CzechRepublic(294), europe-Denmark(295), europe-Estonia(296), europe-Finland(297), europe-France(298), europe-Germany(299), europe-Gibraltar(300), europe-Greece(301), europe-Hungary(302), europe-Ireland(303), europe-Italy(304), europe-Latvia(305), europe-Liechtenstein(306), europe-Lithuania(307), europe-Luxembourg(308), europe-Macedonia(309), europe-Malta(310), europe-Moldova(311), europe-Monaco(312), europe-Montenegro(421), europe-Netherlands(313), europe-Norway(314), europe-Poland(315), europe-Portugal-Mainland(316), europe-Portugal-MadeiraIslands(317), europe-Portugal-Azores(318), europe-Romania(319), europe-Russia-Moscow-01Kaliningrad(320), europe-Russia-Moscow00WestRussia(321), europe-Russia-Moscow01CaspianSea(322), europe-Russia-Moscow02Urals(323), europe-Russia-Moscow03WestSiberia(324), europe-Russia-Moscow03Novosibirsk(325), europe-Russia-Moscow04YeniseiRiver(326), europe-Russia-Moscow05LakeBaikal(327), europe-Russia-Moscow06LenaRiver(328), europe-Russia-Moscow07AmurRiver(329), europe-Russia-Moscow07SakhalinIsland(330), europe-Russia-Moscow08Magadan(331), europe-Russia-Moscow09Kamchatka(332), europe-Russia-Moscow10BeringSea(333), europe-SanMarino(334), europe-Serbia(348), europe-Slovakia(335), europe-Slovenia(336), europe-Spain-Mainland(337), europe-Spain-CeutaAndMelilla(338), europe-Spain-CanaryIslands(339), europe-Sweden(340), europe-Switzerland(341), europe-Turkey(342), europe-Ukraine-MostLocations(343), europe-Ukraine-Ruthenia(344), europe-Ukraine-Zaporozhye-ELugansk(345), europe-Ukraine-CentralCrimea(346), europe-VaticanCity(347), indianOcean-BritishIndianOceanTerritory(349), indianOcean-ChristmasIsland(350), indianOcean-CocosOrKeelingIslands(351), indianOcean-Comoros(352), indianOcean-FrenchSouthernAndAntarcticLands(353), indianOcean-Madagascar(354), indianOcean-Maldives(355), indianOcean-Mauritius(356), indianOcean-Mayotte(357), indianOcean-Reunion(358), indianOcean-Seychelles(359), pacificOcean-Chile-MostLocations(360), pacificOcean-Chile-EasterIslandSalayGomez(361), pacificOcean-CookIslands(362), pacificOcean-Ecuador(363), pacificOcean-Fiji(364), pacificOcean-FrenchPolynesia-SocietyIslands(365), pacificOcean-FrenchPolynesia-MarquesasIslands(366), pacificOcean-FrenchPolynesia-GambierIslands(367), pacificOcean-Guam(368), pacificOcean-Kiribati-GilbertIslands(369), pacificOcean-Kiribati-PhoenixIslands(370), pacificOcean-Kiribati-LineIslands(371), pacificOcean-MarshallIslands-MostLocations(372), pacificOcean-MarshallIslands-Kwajalein(373), pacificOcean-Micronesia-Yap(374), pacificOcean-Micronesia-TrukOrChuuk(375), pacificOcean-Micronesia-PonapeOrPohnpei(376), pacificOcean-Micronesia-Kosrae(377), pacificOcean-Nauru(378), pacificOcean-NewCaledonia(379), pacificOcean-NewZealand-MostLocations(380), pacificOcean-NewZealand-ChathamIslands(381), pacificOcean-Niue(382), pacificOcean-NorfolkIsland(383), pacificOcean-NorthernMarianaIslands(384), pacificOcean-Palau(385), pacificOcean-PapuaNewGuinea(386), pacificOcean-Pitcairn(387), pacificOcean-SamoaAmerican(388), pacificOcean-SamoaWestern(389), pacificOcean-SolomonIslands(390), pacificOcean-Tokelau(391), pacificOcean-Tonga(392), pacificOcean-Tuvalu(393), pacificOceanUSA-EastTime(394), pacificOceanUSA-EastTime-MichiganMostLocations(395), pacificOceanUSA-EastTime-KentuckyLouisvilleArea(396), pacificOceanUSA-EastTime-KentuckyWayneCounty(397), pacificOceanUSA-EastStdTime-IndianaMostLocations(398), pacificOceanUSA-EastStdTime-IndianaCrawfordCounty(399), pacificOceanUSA-EastStdTime-IndianaStarkeCounty(400), pacificOceanUSA-EastStdTime-IndianaSwitzerlandCounty(401), pacificOceanUSA-CentTime(402), pacificOceanUSA-CentTime-MichiganWisconsinborder(403), pacificOceanUSA-CentTime-NorthDakotaOliverCounty(404), pacificOceanUSA-MountTime(405), pacificOceanUSA-MountTime-SouthIdahoAndEastOregon(406), pacificOceanUSA-MountTime-Navajo(407), pacificOceanUSA-MountStdTime-Arizona(408), pacificOceanUSA-PacificTime(409), pacificOceanUSA-AlaskaTime(410), pacificOceanUSA-AlaskaTime-AlaskaPanhandle(411), pacificOceanUSA-AlaskaTime-AlaskaPanhandleNeck(412), pacificOceanUSA-AlaskaTime-WestAlaska(413), pacificOceanUSA-AleutianIslands(414), pacificOceanUSA-Hawaii(415), pacificOcean-USMinorOutlyingIslands-JohnstonAtoll(416), pacificOcean-USMinorOutlyingIslands-MidwayIslands(417), pacificOcean-USMinorOutlyingIslands-WakeIsland(418), pacificOcean-Vanuatu(419), pacificOceanWallisAndFutuna(420) } MAX-ACCESS read-write STATUS current DESCRIPTION "The time zone. Note: Locations are alphabetically ordered and the corresponding code is not reflected in CLI." ::= { agSystem 56 } agCurCfgIdleCLITimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Set idle CLI sessions timeout." ::= { agSystem 57 } agNewCfgIdleCLITimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Set idle CLI sessions timeout." ::= { agSystem 58 } -- Auto-Discovery topology table info agCurCfgHttpsServerAccess OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current HTTPS server access state." ::= { agSystem 62 } agNewCfgHttpsServerAccess OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable HTTPS server access." ::= { agSystem 63 } agCurHttpAcces OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current HTTP server access state." ::= { agSystem 66 } agNewHttpAcces OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "New HTTP server access state." ::= { agSystem 67 } agCurCfgDhcp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the use of DHCP, as currently configured in the current configuration block." ::= { agSystem 68 } agNewCfgDhcp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable the use of DHCP, in the new configuration block." ::= { agSystem 69 } agCurCfgHprompt OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current status of hprompt." ::= { agSystem 72 } agNewCfgHprompt OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "New status of hprompt." ::= { agSystem 73 } agCurCfgUserBBI OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current status of user configuration from BBI." ::= { agSystem 74 } agNewCfgUserBBI OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "New status of user configuration from BBI." ::= { agSystem 75 } agCurCfgSysCustomDstState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of Custom DST" ::= { agSystem 98 } agNewCfgSysCustomDstState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable Custom DST" ::= { agSystem 99 } agCurCfgSysCustomDstStart OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION " The current Custom DST start rule" ::= { agSystem 100 } agNewCfgSysCustomDstStart OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Set Custom DST start rule" ::= { agSystem 101 } agCurCfgSysCustomDstEnd OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The current Custom DST end rule" ::= { agSystem 102} agNewCfgSysCustomDstEnd OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Set Custom DST end rule" ::= { agSystem 103 } agHavePanicDump OBJECT-TYPE SYNTAX INTEGER { havePanic(1), noHavePanic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The presence of a panic dump in the flash memory." ::= { agSystem 104 } agCurCfgResetControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current reset control state." ::= { agSystem 111 } agNewCfgResetControl OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable reset control after panic." ::= { agSystem 112 } agCurCfgSysDlight OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current daylight savings time status." ::= { agSystem 113 } agNewCfgSysDlight OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable daylight savings time." ::= { agSystem 114 } agCurCfgErrDisableRecovery OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the system will automatically re-enable an error-disabled port after the time interval indicated by agCurCfgErrDisableTimeout has elapsed. A port is in error-disabled state when it has been operationally disabled due to abnormal conditions detected on the port. An error-disabled port will only be automatically re-enabled by the system if and only if this object and the port's agPortCurCfgErrDisableRecovery object both have a value of 'enable(1)'." DEFVAL { disable } ::= { agSystem 115 } agNewCfgErrDisableRecovery OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the system should automatically re-enable an error-disabled port. Use this object to change the global setting of the error-disable recovery action." DEFVAL { disable } ::= { agSystem 116 } agCurCfgErrDisableTimeout OBJECT-TYPE SYNTAX INTEGER (30 .. 86400) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the time, in seconds, that the system will wait before it automatically re-enables any port that is in error-disabled state." DEFVAL { 300 } ::= { agSystem 117 } agNewCfgErrDisableTimeout OBJECT-TYPE SYNTAX INTEGER (30 .. 86400) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the time, in seconds, that the system should wait before it automatically re-enables a port that is in error-disabled state. Use this object to change the global error-disable timeout value." DEFVAL { 300 } ::= { agSystem 118 } agCurCfgTelnetAccess OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current telnet access state." ::= { agSystem 119 } agNewCfgTelnetAccess OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable telnet access." ::= { agSystem 120 } serverPortsCurCfgPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The current configured server port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the server ports list 0 - The represented port does not belong to the server ports list" ::= { agSystem 127 } serverPortsNewCfgPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "New configuration server port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the server ports list 0 - The represented port does not belong to the server ports list" ::= { agSystem 128 } serverPortsNewCfgAddPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The port to be added to the server ports list. A '0' value is returned when read." ::= {agSystem 129 } serverPortsNewCfgRemovePort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The port to be removed from the server ports list. A '0' value is returned when read." ::= { agSystem 130 } agCurBootProfile OBJECT-TYPE SYNTAX INTEGER { default(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Profile that will be used by the switch after reset" ::= { agSystem 131 } agNewBootProfile OBJECT-TYPE SYNTAX INTEGER { default(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configure the profile that will be used by the switch after reset" ::= { agSystem 132 } agNetboot OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Ena/dis loading of config over n/w during bootup" ::= { agSystem 133 } agNetbootTftpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Tftp server address from where config file needs to be downloaded" ::= { agSystem 134 } agNetbootCfgFile OBJECT-TYPE SYNTAX DisplayString (SIZE(0..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "Config file location on tftp server" ::= { agSystem 135 } agCurCfgLinkscanMode OBJECT-TYPE SYNTAX INTEGER { normal(1), fast(2), slow(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set linkscan mode" ::= { agSystem 136 } agNewCfgLinkscanMode OBJECT-TYPE SYNTAX INTEGER { normal(1), fast(2), slow(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set linkscan mode" ::= { agSystem 137 } agUSBboot OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Ena/dis USB Boot capability" ::= { agSystem 138 } agCurServiceLED OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Ena/dis Service Required LED" ::= { agSystem 139 } agNewServiceLED OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Ena/dis Service Required LED " ::= { agSystem 140 } agUSBeject OBJECT-TYPE SYNTAX INTEGER { eject(1), usbready(2), nousb(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Eject USB - eject(1) Get current USB state: usbready(2) - USB mounted nousb(3) - no USB mounted" ::= { agSystem 141 } agCurRFC4741NetconfAccess OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current NETCONF server access state." ::= { agSystem 142 } agNewRFC4741NetconfAccess OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable NETCONF server access state." ::= { agSystem 143 } agCurRFC4741NetconfSessionTimeout OBJECT-TYPE SYNTAX INTEGER (60..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "Once NETCONF session setup, NETCONF server will allocate resource for this session. agCurRFC4741NetconfSessionTimeout indicates the number of seconds before the resources are freed if there is no operation on this session" ::= { agSystem 144 } agNewRFC4741NetconfSessionTimeout OBJECT-TYPE SYNTAX INTEGER (60..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "Once NETCONF session setup, NETCONF server will allocate resource for this session. agNewRFC4741NetconfSessionTimeout specifies the number of seconds before the resources are freed if there is no operation on this session" ::= { agSystem 145 } agCurRFC4741NetconfSshAccess OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current NETCONF server over SSH access state." ::= { agSystem 146 } agNewRFC4741NetconfSshAccess OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable NETCONF server over SSH access state." ::= { agSystem 147 } agCurRFC4741NetconfSshPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP port number that the NETCONF server over SSH is listening to in the current configuration block." ::= { agSystem 148 } agNewRFC4741NetconfSshPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP port number that the NETCONF server over SSH is listening to in the new configuration block." ::= { agSystem 149} agCurCfgLFDStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the system will put any port in an error-disabled state due to excessive link flaps. A port will be put in an error-disabled state due to excessive link flaps if this object and the port's agPortCurCfgLFDStatus object both have a value of 'enable'. A port has an excessive number of link flaps if the number of link flaps detected during a time period in seconds indicated by agCurCfgLFDTime exceeds the maximum number of allowed flaps indicated by agCurCfgLFDFlaps." DEFVAL { disable } ::= { agSystem 158 } agNewCfgLFDStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the system should put any port in an error-disabled state due to excessive link flaps. Use this object to change the global setting of the Link Flap Dampening error-disable action." DEFVAL { disable } ::= { agSystem 159 } agCurCfgLFDFlaps OBJECT-TYPE SYNTAX INTEGER (1 .. 100) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of flaps allowed in a time period set by agCurCfgLFDTime." DEFVAL { 5 } ::= { agSystem 160 } agNewCfgLFDFlaps OBJECT-TYPE SYNTAX INTEGER (1 .. 100) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the maximum number of flaps that should be allowed in a time period. Use this object to change the global maximum number of flaps allowed in a time period." DEFVAL { 5 } ::= { agSystem 161 } agCurCfgLFDTime OBJECT-TYPE SYNTAX INTEGER (5 .. 500) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the length of time period in seconds during which link flaps are counted." DEFVAL { 30 } ::= { agSystem 162 } agNewCfgLFDTime OBJECT-TYPE SYNTAX INTEGER (5 .. 500) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the length of time period in seconds that should be used to count link flaps." DEFVAL { 30 } ::= { agSystem 163 } agCurCfgTrapSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the loopback interface that should be used for the source IP of the SNMP trap; 0 means that no loopback interface is used as the source of the SNMP trap." ::= { agSystem 164 } agNewCfgTrapSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The index of the loopback interface that should be used for the source IP of the SNMP trap; 0 means that no loopback interface is used as the source of the SNMP trap." ::= { agSystem 165 } agCfgMtm OBJECT-TYPE SYNTAX INTEGER { mtmValue1(1), mtmValue2(2), mtmValue3(3), mtmValue4(4), mtmValue5(5) ,mtmValue6(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the new value for MTM. The available MTM values are: 1455-48E (1) 7309-52F (2) 7309-G52 (3) 7309-HC2 (4) 7309-HC1 (5) 7120-48E (6)" ::= { agSystem 166 } agCurCfgDefipData OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the use of default IP address on data interface, as configured in the current configuration block." ::= { agSystem 167 } agNewCfgDefipData OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable the use of default IP address on data interface, in the new configuration block." ::= { agSystem 168 } agNewSecurityMode OBJECT-TYPE SYNTAX INTEGER { compatibility(0), strict(1), strictsnmpolduser(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to change switch security mode. There are thtree security modes for IBM switch: strict mode, compatibility mode and strict mode with SNMP not comply. Strict mode: Strict mode will have higher security level. Encryption algorithms in strict mode will be compliance with the NIST SP 800-131A. Detailed information please refer NIST SP 800-131A mode Functional Specification. SSH will be enabled by default in strict mode for all platforms. It's strict(1) in this node. Compatibility mode: This is the default mode when switch first boot up. MD5/SHA/DES are selected as Hash/Encryption algorithms. It's compatibility(2) in this node. Strict mode with SNMP not comply: To provide backward compatibility option, insecure MD5/DES are supported. It's strictsnmpolduser(3) in this node. The next time reload security mode is returned when this object ie read." ::= { agSystem 177 } agCurSecurityMode OBJECT-TYPE SYNTAX INTEGER { compatibility(0), strict(1), strictsnmpolduser(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is an action object to change switch security mode. There are thtree security modes for IBM switch: strict mode, compatibility mode and strict mode with SNMP not comply. Strict mode: Strict mode will have higher security level. Encryption algorithms in strict mode will be compliance with the NIST SP 800-131A. Detailed information please refer NIST SP 800-131A mode Functional Specification. SSH will be enabled by default in strict mode for all platforms. It's strict(1) in this node. Compatibility mode: This is the default mode when switch first boot up. MD5/SHA/DES are selected as Hash/Encryption algorithms. It's compatibility(2) in this node. Strict mode with SNMP not comply: To provide backward compatibility option, insecure MD5/DES are supported. It's strictsnmpolduser(3) in this node. The current security mode is returned when this object ie read." ::= { agSystem 180 } agNewCfgSslVersionLevel OBJECT-TYPE SYNTAX INTEGER { -- sslv3(0), tls10(1), tls11(2), tls12(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "New status of SSL Server Minimum Acceptable Protocol Version." ::= { agSystem 178 } agCurCfgSslVersionLevel OBJECT-TYPE SYNTAX INTEGER { -- sslv3(0), tls10(1), tls11(2), tls12(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current status of SSL Server Minimum Acceptable Protocol Version." ::= { agSystem 179 } agCurCfgTrapHostTable OBJECT-TYPE SYNTAX SEQUENCE OF AgCurCfgTrapHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of current trap hosts configure." ::= { agSystem 184 } agCurCfgTrapHostEntry OBJECT-TYPE SYNTAX AgCurCfgTrapHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A trap host configuration on the switch." INDEX { agCurCfgTrapHostIndex } ::= { agCurCfgTrapHostTable 1 } AgCurCfgTrapHostEntry ::= SEQUENCE { agCurCfgTrapHostIndex Integer32, agCurCfgTrapHostAddress DisplayString , agCurCfgTrapHostCommStr DisplayString } agCurCfgTrapHostIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The trap host index. Valid range is 1-16" ::= { agCurCfgTrapHostEntry 1 } agCurCfgTrapHostAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The trap host address." ::= { agCurCfgTrapHostEntry 2 } agCurCfgTrapHostCommStr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The trap host community string." ::= { agCurCfgTrapHostEntry 3 } agNewCfgTrapHostTable OBJECT-TYPE SYNTAX SEQUENCE OF AgNewCfgTrapHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for trap host definitions in the new configuration block." ::= { agSystem 185 } agNewCfgTrapHostEntry OBJECT-TYPE SYNTAX AgNewCfgTrapHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the trap host definition table" INDEX { agNewCfgTrapHostIndex } ::= { agNewCfgTrapHostTable 1 } AgNewCfgTrapHostEntry ::= SEQUENCE { agNewCfgTrapHostIndex Integer32, agNewCfgTrapHostAddress DisplayString , agNewCfgTrapHostCommStr DisplayString, agNewCfgTrapHostDelete INTEGER } agNewCfgTrapHostIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The trap host index. Valid range is 1-16" ::= { agNewCfgTrapHostEntry 1 } agNewCfgTrapHostAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The trap host address in the new configuration block. Setting IPv6 value is not supported in realease 7.9.x." ::= { agNewCfgTrapHostEntry 2 } agNewCfgTrapHostCommStr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "The trap host community string in the new configuration block." ::= { agNewCfgTrapHostEntry 3 } agNewCfgTrapHostDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "By setting the value to delete(2), the entire row is deleted." ::= { agNewCfgTrapHostEntry 4 } -- if defined(WEB_UI) removed this as it is wrongfully tied to BBI and did not allowed -- agent to compile without web folder (BBI) -- Syslog Configuration agCurCfgSyslogHost OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The syslog host IP address in the current configuration block." ::= { agSyslog 1 } agNewCfgSyslogHost OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The syslog host IP address in the new configuration block." ::= { agSyslog 2 } agCurCfgSyslog2Host OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The second syslog host IP address in the current configuration block." ::= { agSyslog 3 } agNewCfgSyslog2Host OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The second syslog host IP address in the new configuration block." ::= { agSyslog 4 } agCurCfgSyslogFac OBJECT-TYPE SYNTAX INTEGER { local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The facility level of syslog host in the current configuration block." ::= { agSyslog 5 } agNewCfgSyslogFac OBJECT-TYPE SYNTAX INTEGER { local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The facility level of syslog host in the new configuration block." ::= { agSyslog 6 } agCurCfgSyslog2Fac OBJECT-TYPE SYNTAX INTEGER { local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The facility level of second syslog host in the current configuration block." ::= { agSyslog 7 } agNewCfgSyslog2Fac OBJECT-TYPE SYNTAX INTEGER { local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The facility level of second syslog host in the new configuration block." ::= { agSyslog 8 } agCurCfgSyslogSev OBJECT-TYPE SYNTAX INTEGER { emerg0(1), alert1(2), crit2(3), err3(4), warning4(5), notice5(6), info6(7), debug7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The severity of syslog host in the current configuration block." ::= { agSyslog 13 } agNewCfgSyslogSev OBJECT-TYPE SYNTAX INTEGER { emerg0(1), alert1(2), crit2(3), err3(4), warning4(5), notice5(6), info6(7), debug7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The severity of syslog host in the new configuration block." ::= { agSyslog 14 } agCurCfgSyslog2Sev OBJECT-TYPE SYNTAX INTEGER { emerg0(1), alert1(2), crit2(3), err3(4), warning4(5), notice5(6), info6(7), debug7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The severity of syslog2 host in the current configuration block." ::= { agSyslog 15 } agNewCfgSyslog2Sev OBJECT-TYPE SYNTAX INTEGER { emerg0(1), alert1(2), crit2(3), err3(4), warning4(5), notice5(6), info6(7), debug7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The severity of syslogs host in the new configuration block." ::= { agSyslog 16 } agCurCfgSyslogConsoleSev OBJECT-TYPE SYNTAX INTEGER { emerg0(1), alert1(2), crit2(3), err3(4), warning4(5), notice5(6), info6(7), debug7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The severity of syslogs console in the current configuration block." ::= { agSyslog 23 } agNewCfgSyslogConsoleSev OBJECT-TYPE SYNTAX INTEGER { emerg0(1), alert1(2), crit2(3), err3(4), warning4(5), notice5(6), info6(7), debug7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The severity of syslogs console in the new configuration block." ::= { agSyslog 24 } agCurCfgSyslogFlashSev OBJECT-TYPE SYNTAX INTEGER { emerg0(1), alert1(2), crit2(3), err3(4), warning4(5), notice5(6), info6(7), debug7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The severity of syslogs flash in the current configuration block." ::= { agSyslog 25 } agNewCfgSyslogFlashSev OBJECT-TYPE SYNTAX INTEGER { emerg0(1), alert1(2), crit2(3), err3(4), warning4(5), notice5(6), info6(7), debug7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The severity of syslogs flash in the new configuration block." ::= { agSyslog 26 } agClrSyslogMsgs OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clears all current Syslog messages." ::= { agSyslog 9 } agSyslogMsgTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the syslog message table." ::= { agSyslog 10 } agCurCfgSyslogSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the loopback interface that should be used for the source IP of the syslog message; 0 means that no loopback interface is used as the source of the syslog message." ::= { agSyslog 21 } agNewCfgSyslogSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The index of the loopback interface that should be used for the source IP of the syslog message; 0 means that no loopback interface is used as the source of the syslog message." ::= { agSyslog 22 } agSyslogMsgTable OBJECT-TYPE SYNTAX SEQUENCE OF AgSyslogMsgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of syslog messages." ::= { agSyslog 11 } agSyslogMsgTableEntry OBJECT-TYPE SYNTAX AgSyslogMsgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A syslog message stored on the switch." INDEX { agSyslogMsgIndex } ::= { agSyslogMsgTable 1 } AgSyslogMsgTableEntry ::= SEQUENCE { agSyslogMsgIndex Integer32, agSyslogMessage DisplayString } agSyslogMsgIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The syslog message table index." ::= { agSyslogMsgTableEntry 1 } agSyslogMessage OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The syslog message." ::= { agSyslogMsgTableEntry 2 } agLog OBJECT IDENTIFIER ::= { agSyslog 12 } agNewCfgSyslogTrapConsole OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable console syslog and SNMP trap in the new configuration block." ::= { agLog 1 } agCurCfgSyslogTrapConsole OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable console syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 2 } agNewCfgSyslogTrapSystem OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable system level syslog and SNMP trap in the new configuration block." ::= { agLog 3 } agCurCfgSyslogTrapSystem OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable system level syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 4 } agNewCfgSyslogTrapMgmt OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable management(flash, config, login) syslog and SNMP trap in the new configuration block." ::= { agLog 5 } agCurCfgSyslogTrapMgmt OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable management(flash, config, login) syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 6 } agNewCfgSyslogTrapCli OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable CLI generated error syslog and SNMP trap in the new configuration block." ::= { agLog 7 } agCurCfgSyslogTrapCli OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable CLI generated error syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 8 } agNewCfgSyslogTrapStg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable spanning tree syslog and SNMP trap in the new configuration block." ::= { agLog 9 } agCurCfgSyslogTrapStg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable spanning tree syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 10 } agNewCfgSyslogTrapVlan OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable VLAN syslog and SNMP trap in the new configuration block." ::= { agLog 11 } agCurCfgSyslogTrapVlan OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable VLAN syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 12 } agNewCfgSyslogTrapSsh OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable SSH, RADIUS syslog and SNMP trap in the new configuration block." ::= { agLog 19 } agCurCfgSyslogTrapSsh OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable SSH, RADIUS syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 20 } agNewCfgSyslogTrapVrrp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable VRRP syslog and SNMP trap in the new configuration block." ::= { agLog 21 } agCurCfgSyslogTrapVrrp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable VRRP syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 22 } agNewCfgSyslogTrapBgp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable BGP syslog and SNMP trap in the new configuration block." ::= { agLog 23 } agCurCfgSyslogTrapBgp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable BGP syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 24 } agNewCfgSyslogTrapNtp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable NTP syslog and SNMP trap in the new configuration block." ::= { agLog 25 } agCurCfgSyslogTrapNtp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable NTP syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 26 } agNewCfgSyslogTrapIp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable IP related syslog and SNMP trap in the new configuration block." ::= { agLog 31 } agCurCfgSyslogTrapIp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable IP related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 32 } agNewCfgSyslogTrapWeb OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable WEBUI related syslog and SNMP trap in the new configuration block." ::= { agLog 35 } agCurCfgSyslogTrapWeb OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable WEBUI related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 36 } agNewCfgSyslogTrapOspf OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable OSPF related syslog and SNMP trap in the new configuration block." ::= { agLog 41 } agCurCfgSyslogTrapOspf OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable OSPF related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 42 } agNewCfgSyslogTrapRmon OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable RMON related syslog and SNMP trap in the new configuration block." ::= { agLog 45 } agCurCfgSyslogTrapRmon OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable RMON related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 46 } agNewCfgSyslogTrap8021x OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable 802.1x related syslog and SNMP trap in the new configuration block." ::= { agLog 49 } agCurCfgSyslogTrap8021x OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable 802.1x related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 50 } -- 802.1x port stats table dot1xPortStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1xPortStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of 802.1x port statistics." ::= { portStats 2 } dot1xPortStatsTableEntry OBJECT-TYPE SYNTAX Dot1xPortStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the 802.1x port stats table." INDEX { dot1xPortStatsIndx } ::= { dot1xPortStatsTable 1 } Dot1xPortStatsTableEntry ::= SEQUENCE { dot1xPortStatsIndx PortNumber, eapolFramesRx Integer32, eapolFramesTx Integer32, eapolStartFramesRx Integer32, eapolLogoffFramesRx Integer32, eapolRespIdFramesRx Integer32, eapolRespFramesRx Integer32, eapolReqIdFramesTx Integer32, eapolReqFramesTx Integer32, invalidEapolFramesRx Integer32, eapLengthErrorFramesRx Integer32, authEntersConnecting Integer32, authEapLogoffsWhileConnecting Integer32, authEntersAuthenticating Integer32, authSuccessesWhileAuthenticating Integer32, authTimeoutsWhileAuthenticating Integer32, authFailWhileAuthenticating Integer32, authReauthsWhileAuthenticating Integer32, authEapStartsWhileAuthenticating Integer32, authEapLogoffWhileAuthenticating Integer32, authReauthsWhileAuthenticated Integer32, authEapStartsWhileAuthenticated Integer32, authEapLogoffWhileAuthenticated Integer32, backendResponses Integer32, backendAccessChallenges Integer32, backendOtherRequestsToSupplicant Integer32, backendNonNakResponsesFromSupplicant Integer32, backendAuthSuccesses Integer32, backendAuthFails Integer32, lastEapolFrameVersion Integer32, lastEapolFrameSource MacAddress } dot1xPortStatsIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The 802.1x port stats index." ::= { dot1xPortStatsTableEntry 1 } eapolFramesRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 2 } eapolFramesTx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 3 } eapolStartFramesRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 4 } eapolLogoffFramesRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 5 } eapolRespIdFramesRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 6 } eapolRespFramesRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 7 } eapolReqIdFramesTx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 8 } eapolReqFramesTx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 9 } invalidEapolFramesRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= {dot1xPortStatsTableEntry 10 } eapLengthErrorFramesRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 11 } authEntersConnecting OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 12 } authEapLogoffsWhileConnecting OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 13 } authEntersAuthenticating OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 14 } authSuccessesWhileAuthenticating OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 15 } authTimeoutsWhileAuthenticating OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 16 } authFailWhileAuthenticating OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 17 } authReauthsWhileAuthenticating OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 18 } authEapStartsWhileAuthenticating OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 19 } authEapLogoffWhileAuthenticating OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 20 } authReauthsWhileAuthenticated OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 21 } authEapStartsWhileAuthenticated OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 22 } authEapLogoffWhileAuthenticated OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 23 } backendResponses OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 24 } backendAccessChallenges OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 25 } backendOtherRequestsToSupplicant OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 26 } backendNonNakResponsesFromSupplicant OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 27 } backendAuthSuccesses OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 28 } backendAuthFails OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 29 } lastEapolFrameVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 30 } lastEapolFrameSource OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dot1xPortStatsTableEntry 31 } agNewCfgSyslogTrapCfg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable CFG related syslog and SNMP trap in the new configuration block." ::= { agLog 53 } agCurCfgSyslogTrapCfg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable CFG related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 54 } agNewCfgSyslogTrapServer OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable Server related syslog and SNMP trap in the new configuration block." ::= { agLog 55 } agCurCfgSyslogTrapServer OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable Server related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 56 } agNewCfgSyslogTrapDifftrak OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable Difftrak related syslog and SNMP trap in the new configuration block." ::= { agLog 57 } agCurCfgSyslogTrapDifftrak OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable Difftrak related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 58 } agNewCfgSyslogTrapHotlinks OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable Hot Links related syslog and SNMP trap in the new configuration block." ::= { agLog 61 } agCurCfgSyslogTrapHotlinks OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable Hot Links related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 62 } agNewCfgSyslogTrapLldp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable LLDP related syslog and SNMP trap in the new configuration block." ::= { agLog 63 } agCurCfgSyslogTrapLldp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable LLDP related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 64 } agNewCfgSyslogTrapAll OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable all syslog and SNMP traps in the new configuration block." ::= { agLog 65 } agCurCfgSyslogTrapAll OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable all syslog and SNMP traps, as configured in the current configuration block." ::= { agLog 66 } agNewCfgSyslogTrapIpv6 OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable IPv6 related syslog and SNMP trap in the new configuration block." ::= { agLog 67 } agCurCfgSyslogTrapIpv6 OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable IPv6 related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 68 } agNewCfgSyslogTrapFailover OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable failover related syslog and SNMP trap in the new configuration block." ::= { agLog 73 } agCurCfgSyslogTrapFailover OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable failover related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 74 } agNewCfgSyslogTrapLacp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable LACP syslog and SNMP trap in the new configuration block." ::= { agLog 77 } agCurCfgSyslogTrapLacp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable LACP syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 78 } agNewCfgSyslogTrapLink OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable all syslog and SNMP traps, in link up/down." ::= { agLog 79 } agCurCfgSyslogTrapLink OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable all syslog and SNMP traps, as currently configured in link up/down." ::= { agLog 80 } agNewCfgSyslogTrapOspfv3 OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable OSPFv3 related syslog and SNMP trap in the new configuration block." ::= { agLog 81 } agCurCfgSyslogTrapOspfv3 OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable OSPFv3 related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 82 } agNewCfgSyslogTrapVm OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable all VM-related syslog and SNMP traps." ::= { agLog 89 } agCurCfgSyslogTrapVm OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable all VM-related syslog and SNMP traps." ::= { agLog 90 } agNewCfgSyslogTrapCfgchg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable configuration change related syslog and SNMP trap in the new configuration block." ::= { agLog 93 } agCurCfgSyslogTrapCfgchg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable configuration change related syslog and SNMP trap, as configured in the current configuration block." ::= { agLog 94 } agNewCfgSyslogTrapVlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable Vlag related syslog and SNMP trap." ::= { agLog 95 } agCurCfgSyslogTrapVlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable Vlag related syslog and SNMP trap." ::= { agLog 96 } agNewCfgSyslogTrapIgmpGroup OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable all IGMP GROUP-related syslog and SNMP traps." ::= { agLog 99 } agCurCfgSyslogTrapIgmpGroup OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable all IGMP GROUP-related syslog and SNMP traps." ::= { agLog 100 } agNewCfgSyslogTrapIgmpMrouter OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable all IGMP MROUTER-related syslog and SNMP traps." ::= { agLog 101 } agCurCfgSyslogTrapIgmpMrouter OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable all IGMP MROUTER-related syslog and SNMP traps." ::= { agLog 102 } agNewCfgSyslogTrapIgmpQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable all IGMP QUERIER-related syslog and SNMP traps." ::= { agLog 103 } agCurCfgSyslogTrapIgmpQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable all IGMP QUERIER-related syslog and SNMP traps." ::= { agLog 104 } agNewCfgSyslogTrapMld OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable all MLD-related syslog and SNMP traps." ::= { agLog 105 } agCurCfgSyslogTrapMld OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable all MLD-related syslog and SNMP traps." ::= { agLog 106 } agNewCfgSyslogTrapPrivateVlan OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable all Private VLAN-related syslog and SNMP traps, as configured in the new configuration block." ::= { agLog 107 } agCurCfgSyslogTrapPrivateVlan OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable all Private VLAN-related syslog and SNMP traps, as configured in the current configuration block." ::= { agLog 108 } agNewCfgSyslogTrapSlp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable all SLP-related syslog and SNMP traps, as configured in the new configuration block." ::= { agLog 109 } agCurCfgSyslogTrapSlp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable all SLP-related syslog and SNMP traps, as configured in the current configuration block." ::= { agLog 110 } -- TFTP Config agTransferServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The FTP/TFTP server IP address or domain name." ::= { agTransfer 1 } agTransferImage OBJECT-TYPE SYNTAX INTEGER { image1(2), image2(3), boot(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether the image file should be loaded in image1 or image2 in flash." ::= { agTransfer 2 } agTransferImageFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The image file name to be transferred." ::= { agTransfer 3 } agTransferCfgFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The configuration file name." ::= { agTransfer 4 } agTransferDumpFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The core dump file name." ::= { agTransfer 5 } agTransferAction OBJECT-TYPE SYNTAX INTEGER { other(1), img-get(2), cfg-get(3), cfg-put(4), dump-put(5), img-put(7), tsdump-put(8) ,ca-get(14) ,hostcert-get(15) ,hostkey-get(16) ,pubkey-get(17) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to perform various FTP/TFTP Get or Put functions. The FTP/TFTP sever is specified in agTransferServer object. img-get(2) - Download switch image from a specified image file(agTransferImageFileName) on the FTP/TFTP server to the destinated storage(agTransferImage). The duration of the action will depend on the image downloading and writting time on the network element. Sugguest 150 seconds timeout setting in MIB Browser to get the correct response for this action. cfg-get(3) - Download switch configuration from a specified file(agTransferCfgFileName) on the FTP/TFTP server. cfg-put(4) - Upload switch configuration to a specified file(agTransferCfgFileName) on the FTP/TFTP server. dump-put(5) - Download switch core dump to a specified file(agTransferDumpFileName) on the FTP/TFTP server. bkpdump-put(6)- Download switch backup core dump to a specified file(agTransferDumpFileName) on the FTP/TFTP server. img-put(7) - Upload specified switch image to a specified image file(agTransferImageFileName) on the FTP/TFTP server. tsdump-put(8) - Download switch tech support dump to a specified file(agTransferTSDumpFileName) on the FTP/TFTP server. bogon-get(9) - Download bogon config file from a specified bogon file(uses agTransferImageFileName) on the FTP/TFTP server. ca-get(14) - Download CA root certificate from a specified file(agTransferCaFileName) on the TFTP server. This command did not support FTP. hostcert-get(15) - Download host certificate from a specified file(agTransferHostCertFileName) on the TFTP server. This command did not support FTP. hostkey-get(16) - Download host private key from a specified file(agTransferHostKeyFileName) on the TFTP server. This command did not support FTP. pubkey-get(17) - Download SSH client public key from a specified file(agTransferPublicKeyFileName) on the TFTP/SFTP server. This command did not support FTP. other(1) is returned always when read." ::= { agTransfer 6 } agTransferLastActionStatus OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The recorded status of the previous FTP/TFTP activity." ::= { agTransfer 7 } agTransferUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The username for the FTP server or blank for TFTP server." ::= { agTransfer 9 } agTransferPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The password for the FTP server. For security reason, an empty string will be returned when the OID is read." ::= { agTransfer 10 } agTransferTSDumpFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The TS dump file name." ::= { agTransfer 11 } agTransferLastConfigurationActionStatus OBJECT-TYPE SYNTAX INTEGER { successfully(1), failed(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the last configuration action using the file ftp/tftp'd from server." ::= { agTransfer 14 } agTransferCaFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The CA certificate file name." ::= { agTransfer 15 } agTransferHostCertFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Host certificate file name." ::= { agTransfer 16 } agTransferHostKeyFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Host private key file name." ::= { agTransfer 17 } agTransferProtocol OBJECT-TYPE SYNTAX INTEGER { tftp(1), ftp(2), sftp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The protocol used by this transfer." ::= { agTransfer 18 } agServerPort OBJECT-TYPE SYNTAX INTEGER { tftp(69), ftp(21), sftp(22) } MAX-ACCESS read-write STATUS current DESCRIPTION "The port is listened on the server." ::= { agTransfer 19 } agTransferPublicKeyUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "The user of the public key file." ::= { agTransfer 21 } agTransferPublicKeyFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The client pulic key file name." ::= { agTransfer 22 } -- Agent Port Table agPortTableMaxEnt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the port configuration host table." ::= { agPortConfig 1 } agPortCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AgPortCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of port configuration in the current configuration block." ::= { agPortConfig 2 } agPortCurCfgTableEntry OBJECT-TYPE SYNTAX AgPortCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the port table in the current configuration block." INDEX { agPortCurCfgIndx } ::= { agPortCurCfgTable 1 } AgPortCurCfgTableEntry ::= SEQUENCE { agPortCurCfgIndx PortNumber, agPortCurCfgState INTEGER, agPortCurCfgVlanTag INTEGER, agPortCurCfgRmon INTEGER, agPortCurCfgPVID Integer32, agPortCurCfgGigEthAutoNeg INTEGER, agPortCurCfgGigEthFctl INTEGER, agPortCurCfgLinkTrap INTEGER, agPortCurCfgGigEthSpeed INTEGER, agPortCurCfgGigEthMode INTEGER, agPortCurCfgDscpRemarking INTEGER, agPortCurCfgTagPVID INTEGER, agPortCurCfgTagiPVID INTEGER, agPortCurCfgMulticastThreshold INTEGER, agPortCurCfgMulticastThresholdRate INTEGER, agPortCurCfgBroadcastThreshold INTEGER, agPortCurCfgBroadcastThresholdRate INTEGER, agPortCurCfgDLFThreshold INTEGER, agPortCurCfgDLFThresholdRate INTEGER, agPortCurCfgPortAlias DisplayString, agPortCurCfgPortName DisplayString ,agPortCurCfgLearning INTEGER ,agPortCurCfgFloodBlocking INTEGER ,agPortCurCfgType DisplayString ,agPortCurCfgLinkType INTEGER ,agPortCurCfgEdge INTEGER ,agPortCurCfgErrDisableRecovery INTEGER ,agPortCurCfgUdld INTEGER ,agPortCurCfgUdldMode INTEGER ,agPortCurCfgOam INTEGER ,agPortCurCfgOamMode INTEGER ,agPortCurCfgBpduGuard INTEGER ,agPortCurCfgMacAddrNotif INTEGER ,agPortCurCfgStpExtGuard INTEGER ,agPortCurCfgLFDStatus INTEGER ,agPortCurCfgEvbProfId INTEGER ,agPortCurCfgReflectRelay INTEGER ,agPortCurCfgPrivateVlanStatus INTEGER ,agPortCurCfgMappedPrimaryVlans OCTET STRING ,agPortCurCfgAssociatedSecondaryVlans OCTET STRING } agPortCurCfgIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the row in port configurations table." ::= { agPortCurCfgTableEntry 1 } agPortCurCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the state of the port." ::= { agPortCurCfgTableEntry 2 } agPortCurCfgVlanTag OBJECT-TYPE SYNTAX INTEGER { tagged(2), untagged(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is VLAN tag state of the port" ::= { agPortCurCfgTableEntry 3 } agPortCurCfgRmon OBJECT-TYPE SYNTAX INTEGER { on(2), off(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used to turn RMON on or off on the port." ::= { agPortCurCfgTableEntry 5 } agPortCurCfgPVID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The default VLAN ID for the port. " ::= { agPortCurCfgTableEntry 6 } agPortCurCfgGigEthAutoNeg OBJECT-TYPE SYNTAX INTEGER { on(2), off(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used to turn the autonegotiation on or off for gigabit Ethernet connection." ::= { agPortCurCfgTableEntry 11 } agPortCurCfgGigEthFctl OBJECT-TYPE SYNTAX INTEGER { transmit(2), receive(3), both(4), none(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used to select port flow control for gigabit Ethernet connection." ::= { agPortCurCfgTableEntry 12 } agPortCurCfgPortName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch port name." ::= { agPortCurCfgTableEntry 13 } agPortCurCfgLinkTrap OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which do not operate on 'top' of any other interface (as defined in the ifStackTable), and disabled(2) otherwise." ::= { agPortCurCfgTableEntry 16 } agPortCurCfgGigEthSpeed OBJECT-TYPE SYNTAX INTEGER { mbs10(2), mbs100(3), any(4), mbs1000(5) , mbs10000(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Selects the port speed for Gigabit Ethernet connection." ::= { agPortCurCfgTableEntry 21 } agPortCurCfgGigEthMode OBJECT-TYPE SYNTAX INTEGER { full-duplex(2), half-duplex(3), any(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object is used to select port mode for Gigabit Ethernet connection." ::= { agPortCurCfgTableEntry 22 } agPortCurCfgDscpRemarking OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable Dscp remarking for the switch port." ::= { agPortCurCfgTableEntry 23 } agPortCurCfgPortAlias OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch port alias." ::= { agPortCurCfgTableEntry 24 } agPortCurCfgTagPVID OBJECT-TYPE SYNTAX INTEGER { tagged(2), untagged(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is PVID tag state of the port" ::= { agPortCurCfgTableEntry 25 } agPortCurCfgLearning OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable L2 (FDB) Learning for the switch port." ::= { agPortCurCfgTableEntry 26 } agPortCurCfgFloodBlocking OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable flood blocking for the switch port." ::= { agPortCurCfgTableEntry 27 } agPortCurCfgType OBJECT-TYPE SYNTAX DisplayString (SIZE(0..7)) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch port type." ::= { agPortCurCfgTableEntry 29 } agPortCurCfgLinkType OBJECT-TYPE SYNTAX INTEGER { auto(1), p2p(2), shared(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of port connection. (for PVRST only)" ::= { agPortCurCfgTableEntry 30 } agPortCurCfgEdge OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of port edge." ::= { agPortCurCfgTableEntry 31 } agPortCurCfgErrDisableRecovery OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the system will automatically re-enable this port if it becomes error-disabled. This port will be re-enabled after the time interval specified by the agCurCfgErrDisableTimeout object has elapsed. A port is in error-disabled state when it is operationally disabled due to abnormal conditions detected on the port. If this port is error-disabled, it will only be re-enabled by the system if the agCurCfgErrDisableRecovery object and this object both have a value of 'enable(1)'." DEFVAL { enable } ::= { agPortCurCfgTableEntry 35 } agPortCurCfgUdld OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable UDLD for the switch port." ::= { agPortCurCfgTableEntry 37 } agPortCurCfgUdldMode OBJECT-TYPE SYNTAX INTEGER { normal(1), aggressive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable UDLD mode for the switch port." ::= { agPortCurCfgTableEntry 38 } agPortCurCfgOam OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable OAM Discovery process for the switch port." ::= { agPortCurCfgTableEntry 39 } agPortCurCfgOamMode OBJECT-TYPE SYNTAX INTEGER { active(1), passive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable OAM mode for the switch port." ::= { agPortCurCfgTableEntry 40 } agPortCurCfgBpduGuard OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable BPDU guard for the switch port." ::= { agPortCurCfgTableEntry 41 } agPortCurCfgMulticastThreshold OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current status of the port's Multicast Threshold." ::= { agPortCurCfgTableEntry 42 } agPortCurCfgMulticastThresholdRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current port's Multicast Threshold Rate." ::= { agPortCurCfgTableEntry 43 } agPortCurCfgBroadcastThreshold OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current status of the port's Broadcast Threshold." ::= { agPortCurCfgTableEntry 44 } agPortCurCfgBroadcastThresholdRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current port's Broadcast Threshold Rate." ::= { agPortCurCfgTableEntry 45 } agPortCurCfgDLFThreshold OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current status of the port's Destination Lookup Fail Threshold." ::= { agPortCurCfgTableEntry 46 } agPortCurCfgDLFThresholdRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current port's Destination Lookup Fail Threshold Rate." ::= { agPortCurCfgTableEntry 47 } agPortCurCfgMacAddrNotif OBJECT-TYPE SYNTAX INTEGER{ enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the state of the MAC address notification syslog messages on the port." ::= { agPortCurCfgTableEntry 48 } agPortCurCfgTagiPVID OBJECT-TYPE SYNTAX INTEGER { tagged(2), untagged(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is ingress PVID tag state of the port" ::= { agPortCurCfgTableEntry 49 } agPortCurCfgStpExtGuard OBJECT-TYPE SYNTAX INTEGER { loop(1), root(2), none(3), default(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current state for spanning tree guard type" ::= { agPortCurCfgTableEntry 52 } agPortCurCfgLFDStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the system will put this port in an error-disabled state due to excessive link flaps. A port will be put in an error-disabled state due to excessive link flaps if this object and the global agCurCfgLFDStatus object both have a value of 'enable'. A port has an excessive number of link flaps if the number of link flaps detected during a time period in seconds indicated by agCurCfgLFDTime exceeds the maximum number of allowed flaps indicated by agCurCfgLFDFlaps." DEFVAL { enable } ::= { agPortCurCfgTableEntry 53 } agPortCurCfgEvbProfId OBJECT-TYPE SYNTAX INTEGER (0..16) MAX-ACCESS read-only STATUS current DESCRIPTION "Current EVB Profile ID" ::= { agPortCurCfgTableEntry 56 } agPortCurCfgReflectRelay OBJECT-TYPE SYNTAX INTEGER{ enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current state of reflective relay" ::= { agPortCurCfgTableEntry 59 } agPortCurCfgPrivateVlanStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current state of Private VLAN on this port" ::= { agPortCurCfgTableEntry 61 } agPortCurCfgMappedPrimaryVlans OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Primary VLAN list mapped to port. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 8 || || || ||___ vlan 7 || |____ vlan 6 || . . . ||_________ vlan 1 |__________ reserved where x : 1 - The represented primary VLAN associated to the port 0 - The represented primary VLAN does not associated to the port" ::= { agPortCurCfgTableEntry 62 } agPortCurCfgAssociatedSecondaryVlans OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Secondary VLAN list associated to port. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 8 || || || ||___ vlan 7 || |____ vlan 6 || . . . ||_________ vlan 1 |__________ reserved where x : 1 - The represented secondary VLAN associated to the port 0 - The represented secondary VLAN does not be associated to the port" ::= { agPortCurCfgTableEntry 63 } agPortNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AgPortNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of port configuration in the new configuration block." ::= { agPortConfig 3 } agPortNewCfgTableEntry OBJECT-TYPE SYNTAX AgPortNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the port configuration table in the new configuration block." INDEX { agPortNewCfgIndx } ::= { agPortNewCfgTable 1 } AgPortNewCfgTableEntry ::= SEQUENCE { agPortNewCfgIndx PortNumber, agPortNewCfgState INTEGER, agPortNewCfgVlanTag INTEGER, agPortNewCfgRmon INTEGER, agPortNewCfgPVID Integer32, agPortNewCfgGigEthAutoNeg INTEGER, agPortNewCfgGigEthFctl INTEGER, agPortNewCfgLinkTrap INTEGER, agPortNewCfgGigEthSpeed INTEGER, agPortNewCfgGigEthMode INTEGER, agPortNewCfgDscpRemarking INTEGER, agPortNewCfgTagPVID INTEGER, agPortNewCfgTagiPVID INTEGER, agPortNewCfgMulticastThreshold INTEGER, agPortNewCfgMulticastThresholdRate INTEGER, agPortNewCfgBroadcastThreshold INTEGER, agPortNewCfgBroadcastThresholdRate INTEGER, agPortNewCfgDLFThreshold INTEGER, agPortNewCfgDLFThresholdRate INTEGER, agPortNewCfgPortName DisplayString ,agPortNewCfgLearning INTEGER ,agPortNewCfgFloodBlocking INTEGER ,agPortNewCfgType DisplayString ,agPortNewCfgLinkType INTEGER ,agPortNewCfgEdge INTEGER ,agPortNewCfgErrDisableRecovery INTEGER ,agPortNewCfgUdld INTEGER ,agPortNewCfgUdldMode INTEGER ,agPortNewCfgOam INTEGER ,agPortNewCfgOamMode INTEGER ,agPortNewCfgBpduGuard INTEGER ,agPortNewCfgMacAddrNotif INTEGER ,agPortNewCfgStpExtGuard INTEGER ,agPortNewCfgLFDStatus INTEGER ,agPortNewCfgEvbProfId INTEGER ,agPortNewCfgReflectRelay INTEGER ,agPortNewCfgPrivateVlanStatus INTEGER ,agPortNewCfgMappedPrimaryVlans OCTET STRING ,agPortNewCfgAddPrimaryVlan Unsigned32 ,agPortNewCfgDelPrimaryVlan Unsigned32 ,agPortNewCfgAssociatedSecondaryVlans OCTET STRING ,agPortNewCfgAddSecondaryVlan Unsigned32 ,agPortNewCfgDelSecondaryVlan Unsigned32 } agPortNewCfgIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the row in port configurations table." ::= { agPortNewCfgTableEntry 1 } agPortNewCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the state of the port." ::= { agPortNewCfgTableEntry 2 } agPortNewCfgVlanTag OBJECT-TYPE SYNTAX INTEGER { tagged(2), untagged(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is VLAN tag state of the port" ::= { agPortNewCfgTableEntry 3 } agPortNewCfgRmon OBJECT-TYPE SYNTAX INTEGER { on(2), off(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to turn RMON on or off on the port." ::= { agPortNewCfgTableEntry 5 } agPortNewCfgPVID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The default VLAN ID for the port. " ::= { agPortNewCfgTableEntry 6 } agPortNewCfgGigEthAutoNeg OBJECT-TYPE SYNTAX INTEGER { on(2), off(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to turn the autonegotiation on or off for gigabit Ethernet connection." ::= { agPortNewCfgTableEntry 11 } agPortNewCfgGigEthFctl OBJECT-TYPE SYNTAX INTEGER { transmit(2), receive(3), both(4), none(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to select port flow control for gigabit Ethernet connection." ::= { agPortNewCfgTableEntry 12 } agPortNewCfgPortName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "The switch port name." ::= { agPortNewCfgTableEntry 13 } agPortNewCfgLinkTrap OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enabled(1) for interfaces which do not operate on 'top' of any other interface (as defined in the ifStackTable), and disabled(2) otherwise." ::= { agPortNewCfgTableEntry 16 } agPortNewCfgGigEthSpeed OBJECT-TYPE SYNTAX INTEGER { mbs10(2), mbs100(3), any(4), mbs1000(5) , mbs10000(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Selects the port speed for Gigabit Ethernet connection." ::= { agPortNewCfgTableEntry 21 } agPortNewCfgGigEthMode OBJECT-TYPE SYNTAX INTEGER { full-duplex(2), half-duplex(3), any(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to select port mode for Gigabit Ethernet connection. " ::= { agPortNewCfgTableEntry 22 } agPortNewCfgDscpRemarking OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable Dscp remarking for the switch port." ::= { agPortNewCfgTableEntry 23 } agPortNewCfgTagPVID OBJECT-TYPE SYNTAX INTEGER { tagged(2), untagged(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is PVID tag state of the port" ::= { agPortNewCfgTableEntry 25 } agPortNewCfgLearning OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable L2 (FDB) Learning for the switch port." ::= { agPortNewCfgTableEntry 26 } agPortNewCfgFloodBlocking OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable flood blocking for the switch port." ::= { agPortNewCfgTableEntry 27 } agPortNewCfgType OBJECT-TYPE SYNTAX DisplayString (SIZE(0..7)) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch port type." ::= { agPortNewCfgTableEntry 29 } agPortNewCfgLinkType OBJECT-TYPE SYNTAX INTEGER { auto(1), p2p(2), shared(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of port connection. (for PVRST only)" ::= { agPortNewCfgTableEntry 30 } agPortNewCfgEdge OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of port edge." ::= { agPortNewCfgTableEntry 31 } agPortNewCfgErrDisableRecovery OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the system should automatically re-enable this port when it becomes error-disabled. Use this object to change the port-level setting of the error-disable recovery action." DEFVAL { enable } ::= { agPortNewCfgTableEntry 35 } agPortNewCfgUdld OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable UDLD for the switch port." ::= { agPortNewCfgTableEntry 37 } agPortNewCfgUdldMode OBJECT-TYPE SYNTAX INTEGER { normal(1), aggressive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable UDLD mode for the switch port." ::= { agPortNewCfgTableEntry 38 } agPortNewCfgOam OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable OAM Discovery process for the switch port." ::= { agPortNewCfgTableEntry 39 } agPortNewCfgOamMode OBJECT-TYPE SYNTAX INTEGER { active(1), passive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable OAM mode for the switch port." ::= { agPortNewCfgTableEntry 40 } agPortNewCfgBpduGuard OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable BPDU guard for the switch port." ::= { agPortNewCfgTableEntry 41 } agPortNewCfgMulticastThreshold OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "New status of the port's Multicast Threshold." ::= { agPortNewCfgTableEntry 42 } agPortNewCfgMulticastThresholdRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "New port's Multicast Threshold Rate." ::= { agPortNewCfgTableEntry 43 } agPortNewCfgBroadcastThreshold OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "New status of the port's Broadcast Threshold." ::= { agPortNewCfgTableEntry 44 } agPortNewCfgBroadcastThresholdRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "New port's Broadcast Threshold Rate." ::= { agPortNewCfgTableEntry 45 } agPortNewCfgDLFThreshold OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "New status of the port's Destination Lookup Fail Threshold." ::= { agPortNewCfgTableEntry 46 } agPortNewCfgDLFThresholdRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "New port's Destination Lookup Fail Threshold Rate." ::= { agPortNewCfgTableEntry 47 } agPortNewCfgMacAddrNotif OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables or Disables the MAC address notification syslog messages on the port." ::= { agPortNewCfgTableEntry 48 } agPortNewCfgTagiPVID OBJECT-TYPE SYNTAX INTEGER { tagged(2), untagged(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is ingress PVID tag state of the port" ::= { agPortNewCfgTableEntry 49 } agPortNewCfgStpExtGuard OBJECT-TYPE SYNTAX INTEGER { loop(1), root(2), none(3), default(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set spanning tree guard type" ::= { agPortNewCfgTableEntry 52 } agPortNewCfgLFDStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the system should put this port in an error-disabled state due to excessive link flaps. Use this object to change the port setting of the Link Flap Dampening error-disable action." DEFVAL { enable } ::= { agPortNewCfgTableEntry 53 } agPortNewCfgEvbProfId OBJECT-TYPE SYNTAX INTEGER (0..16) MAX-ACCESS read-write STATUS current DESCRIPTION "Set EVB Profile ID" ::= { agPortNewCfgTableEntry 56 } agPortNewCfgReflectRelay OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable reflective relay for port" ::= { agPortNewCfgTableEntry 59 } agPortNewCfgPrivateVlanStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable the Private VLAN on this port" ::= { agPortNewCfgTableEntry 61 } agPortNewCfgMappedPrimaryVlans OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Primary VLAN list mapped to port. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 8 || || || ||___ vlan 7 || |____ vlan 6 || . . . ||_________ vlan 1 |__________ reserved where x : 1 - The represented primary VLAN associate to the port 0 - The represented primary VLAN does not associate to the port" ::= { agPortNewCfgTableEntry 62 } agPortNewCfgAddPrimaryVlan OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Adds the port to the specified primary VLAN. A '0' value is returned when read." ::= { agPortNewCfgTableEntry 63 } agPortNewCfgDelPrimaryVlan OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Removes the port from the specified primary VLAN. A '0' value is returned when read." ::= { agPortNewCfgTableEntry 64 } agPortNewCfgAssociatedSecondaryVlans OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Secondary VLAN list associated to port. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 8 || || || ||___ vlan 7 || |____ vlan 6 || . . . ||_________ vlan 1 |__________ reserved where x : 1 - The represented secondary VLAN associated to the port 0 - The represented secondary VLAN does not be associated to the port" ::= { agPortNewCfgTableEntry 65 } agPortNewCfgAddSecondaryVlan OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Adds the port to the specified secondary VLAN. A '0' value is returned when read." ::= { agPortNewCfgTableEntry 66 } agPortNewCfgDelSecondaryVlan OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Removes the port from the secondary VLAN. A '0' value is returned when read." ::= { agPortNewCfgTableEntry 67 } -- Agent Fast Forwarding Port Table -- Agent Fast Forwarding Port Table -- SSH Configuration sshCurCfgScpAdm OBJECT-TYPE SYNTAX DisplayString(SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "SCP-only admin password." ::= { agSSHConfig 3 } sshNewCfgScpAdm OBJECT-TYPE SYNTAX DisplayString(SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "Set SCP-only admin password." ::= { agSSHConfig 4 } sshNewCfgHKeyGen OBJECT-TYPE SYNTAX INTEGER { generate(1), other(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to generate the RSA host key. other(2) is returned always when read. The following values are writable: generate(1).. Generate the RSA host key." ::= { agSSHConfig 5 } sshCurCfgSSHPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "SSH server port number." ::= { agSSHConfig 7 } sshNewCfgSSHPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Set SSH server port number." ::= { agSSHConfig 8 } sshCurCfgScpApplySave OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "SCP apply and save." ::= { agSSHConfig 9 } sshNewCfgScpApplySave OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable the SCP apply and save." ::= { agSSHConfig 10 } sshCurCfgStatus OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "SSH server status." ::= { agSSHConfig 11 } sshNewCfgStatus OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Turn SSH server ON/OFF." ::= { agSSHConfig 12 } sshPubKeyRemAll OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove all the public key entries on switch." ::= { agSSHConfig 13 } sshPubKeyRemUser OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a specific username from the public key database." ::= { agSSHConfig 14 } sshPubKeyConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF SshPubKeyConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for ssh public keys and its users." ::= { agSSHConfig 15 } sshPubKeyConfigEntry OBJECT-TYPE SYNTAX SshPubKeyConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the ssh public keys tables." INDEX { sshPubKeyConfigIndex } ::= { sshPubKeyConfigTable 1 } SshPubKeyConfigEntry ::= SEQUENCE { sshPubKeyConfigIndex Integer32, sshPubKeyType INTEGER, sshPubKeyHashValue OCTET STRING, sshPubkeyUserBmap OCTET STRING, sshPubKeyAddUser DisplayString (SIZE(0..64)), sshPubKeyDelUser DisplayString (SIZE(0..64)), sshPubKeyRemEntry INTEGER } sshPubKeyConfigIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ssh public key entry." ::= { sshPubKeyConfigEntry 1 } sshPubKeyType OBJECT-TYPE SYNTAX INTEGER{ rsa(1), dsa(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specify the type of the public key." ::= { sshPubKeyConfigEntry 2 } sshPubKeyHashValue OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The hash value of a specific public key." ::= { sshPubKeyConfigEntry 3 } sshPubkeyUserBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The user list in the key entry. The user are presented in bitmap format. as follows: OCTET 1 OCTET 2 OCTET 3 OCTET 4 xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx || | | |||| ||________ oper || | | |||| |_________ user || | | ||||___________ admin || | | |||____________ maint || | | ||_____________ scpadmin || | | |______________ support || | | || | |________________ user defined 20 || | || | ................... || |______ user defined 5 ||.......... ||.......... ||_________ user defined 2 |__________ default user defined 1: USERID Bit On - The represented user belongs to the key entry Bit Off - The represented user does not belong to the key entry Bit 0-19 represent the 20 user-defined users(uid=BitNUM+1), more details can be found in agAccess->agAccessUserCurCfgTable. Bit 20-25 represent the 6 pre-defined user(from support to oper)." ::= { sshPubKeyConfigEntry 4 } sshPubKeyAddUser OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Add a new user to a particular public key. Reminder: The user must be a valid system user." ::= { sshPubKeyConfigEntry 5 } sshPubKeyDelUser OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a user from the user list of the public key entry." ::= { sshPubKeyConfigEntry 6 } sshPubKeyRemEntry OBJECT-TYPE SYNTAX INTEGER{ other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a public key entry." ::= { sshPubKeyConfigEntry 7 } sshCurCfgSSHAttempts OBJECT-TYPE SYNTAX INTEGER (1..20) MAX-ACCESS read-only STATUS current DESCRIPTION "SSH server maximum authentication attempts." ::= { agSSHConfig 16 } sshNewCfgSSHAttempts OBJECT-TYPE SYNTAX INTEGER (1..20) MAX-ACCESS read-write STATUS current DESCRIPTION "Set SSH server maximum authentication attempts." ::= { agSSHConfig 17 } -- RADIUS Configuration radCurCfgPrimaryServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Hostname of the Primary RADIUS server." ::= { agRadiusConfig 1 } radNewCfgPrimaryServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Hostname of the Primary RADIUS server." ::= { agRadiusConfig 2 } radCurCfgSecondaryServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Hostname of the Secondary RADIUS server." ::= { agRadiusConfig 3 } radNewCfgSecondaryServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Hostname of the Secondary RADIUS server." ::= { agRadiusConfig 4 } radCurCfgPort OBJECT-TYPE SYNTAX INTEGER (1500..3000) MAX-ACCESS read-only STATUS current DESCRIPTION "Specify the RADIUS port number." ::= { agRadiusConfig 5 } radNewCfgPort OBJECT-TYPE SYNTAX INTEGER (1500..3000) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the RADIUS port number." ::= { agRadiusConfig 6 } radCurCfgTimeout OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of seconds before resending authentication to RADIUS server." ::= { agRadiusConfig 7 } radNewCfgTimeout OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of seconds before resending authentication to RADIUS server." ::= { agRadiusConfig 8 } radCurCfgRetries OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of retries to the RADIUS server." ::= { agRadiusConfig 9 } radNewCfgRetries OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries to the RADIUS server." ::= { agRadiusConfig 10 } radCurCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable RADIUS authentication." ::= { agRadiusConfig 11 } radNewCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable RADIUS authentication." ::= { agRadiusConfig 12 } radCurCfgAuthenString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The RADIUS authentication string." ::= { agRadiusConfig 13 } radNewCfgAuthenString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The RADIUS authentication string." ::= { agRadiusConfig 14 } radCurCfgBackdoor OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable RADIUS backdoor for telnet/ssh/http/https." ::= { agRadiusConfig 15 } radNewCfgBackdoor OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable RADIUS backdoor for telnet/ssh/http/https." ::= { agRadiusConfig 16 } radCurCfgAuthenSecondString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The second RADIUS authentication string." ::= { agRadiusConfig 17 } radNewCfgAuthenSecondString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The second RADIUS authentication string." ::= { agRadiusConfig 18 } radCurCfgSecBd OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable RADIUS secure backdoor for telnet." ::= { agRadiusConfig 19 } radNewCfgSecBd OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable RADIUS secure backdoor for telnet." ::= { agRadiusConfig 20 } radCurCfgSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the loopback interface that should be used for the source IP of the Radius message; 0 means that no loopback interface is used as the source of the Radius message." ::= { agRadiusConfig 25 } radNewCfgSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The index of the loopback interface that should be used for the source IP of the Radius message; 0 means that no loopback interface is used as the source of the Radius message." ::= { agRadiusConfig 26 } -- NTP Configuration agCurCfgNTPServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The NTP Server Address." ::= { agNTP 1 } agNewCfgNTPServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The NTP Server Address." ::= { agNTP 2 } agCurCfgNTPResyncInterval OBJECT-TYPE SYNTAX INTEGER (5..44640) MAX-ACCESS read-only STATUS current DESCRIPTION "The NTP Server resync interval in minutes." ::= { agNTP 3 } agNewCfgNTPResyncInterval OBJECT-TYPE SYNTAX INTEGER (5..44640) MAX-ACCESS read-write STATUS current DESCRIPTION "The NTP Server resync interval in minutes." ::= { agNTP 4 } agCurCfgNTPService OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable NTP Service." ::= { agNTP 9 } agNewCfgNTPService OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable NTP Service." ::= { agNTP 10 } agCurCfgNTPSecServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Secondary NTP Server Address." ::= { agNTP 11 } agNewCfgNTPSecServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Secondary NTP Server Address." ::= { agNTP 12 } agCurCfgNTPSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the loopback interface that should be used for the source IP of the NTP packet; 0 means that no loopback interface is used as the source of the NTP packet." ::= { agNTP 17 } agNewCfgNTPSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The index of the loopback interface that should be used for the source IP of the NTP packet; 0 means that no loopback interface is used as the source of the NTP packet." ::= { agNTP 18 } -- APPLY Configuration agApplyPending OBJECT-TYPE SYNTAX INTEGER { applyNeeded(2), noApplyNeeded(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object, when read, gives the user information whether an apply action is needed and that the configuration has been chaged by the user actions. The user then can apply the changes by setting proper value to the object agApplyConfiguration described above." ::= { agApply 1 } agApplyConfig OBJECT-TYPE SYNTAX INTEGER { apply(1), idle(2), inprogress(3), complete(4), failed(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "When this object is read the current state is returned. idle(2) indicates that there is no apply in progess. complete(4) indicates that the last apply operation is completed. Setting the value to apply(1), will write all the changes made since the last apply to the current configuration block. If the apply is successful this variable will return the state 'complete' else it will return 'failed'. In case of failure, to read the reason for failure use the agApplyTable. Once the operation is completed or the agApplyTable is read in case of failure, the apply buffer needs to be freed and the agApplyState should be set back to 'idle' state so others can issue the apply command via SNMP." ::= { agApply 2 } agApplyTableSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of strings in the apply table." ::= { agApply 4 } agApplyTable OBJECT-TYPE SYNTAX SEQUENCE OF AgApplyTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of failure reasons for an apply of current configuration block changes." ::= { agApply 5 } agApplyTableEntry OBJECT-TYPE SYNTAX AgApplyTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of failure reasons for an apply (information about a particular reason of failure)." INDEX { agApplyIndex } ::= { agApplyTable 1 } AgApplyTableEntry ::= SEQUENCE { agApplyIndex Integer32, agApplyString OCTET STRING } agApplyIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The table index." ::= { agApplyTableEntry 1 } agApplyString OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "A string in the apply table." ::= { agApplyTableEntry 2 } -- TACACS+ Configuration tacCurCfgPrimaryServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Hostname of the Primary TACACS+ server." ::= { agTacacsConfig 1 } tacNewCfgPrimaryServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Hostname of the Primary TACACS+ server." ::= { agTacacsConfig 2 } tacCurCfgSecondaryServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Hostname of the Secondary TACACS+ server." ::= { agTacacsConfig 3 } tacNewCfgSecondaryServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Hostname of the Secondary TACACS+ server." ::= { agTacacsConfig 4 } tacCurCfgPort OBJECT-TYPE SYNTAX INTEGER (1..65000) MAX-ACCESS read-only STATUS current DESCRIPTION "Specify the TACACS+ port number." ::= { agTacacsConfig 5 } tacNewCfgPort OBJECT-TYPE SYNTAX INTEGER (1..65000) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the TACACS+ port number." ::= { agTacacsConfig 6 } tacCurCfgTimeout OBJECT-TYPE SYNTAX INTEGER (4..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of seconds before resending authentication to TACACS+ server." ::= { agTacacsConfig 7 } tacNewCfgTimeout OBJECT-TYPE SYNTAX INTEGER (4..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of seconds before resending authentication to TACACS+ server." ::= { agTacacsConfig 8 } tacCurCfgRetries OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of retries to the TACACS+ server." ::= { agTacacsConfig 9 } tacNewCfgRetries OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries to the TACACS+ server." ::= { agTacacsConfig 10 } tacCurCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable TACACS+ authentication." ::= { agTacacsConfig 11 } tacNewCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable TACACS+ authentication." ::= { agTacacsConfig 12 } tacCurCfgAuthenString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The TACACS+ authentication string." ::= { agTacacsConfig 13 } tacNewCfgAuthenString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The TACACS+ authentication string." ::= { agTacacsConfig 14 } tacCurCfgBackdoor OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable TACACS+ backdoor for telnet/ssh/http/https." ::= { agTacacsConfig 15 } tacNewCfgBackdoor OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable TACACS+ backdoor for telnet/ssh/http/https." ::= { agTacacsConfig 16 } tacCurCfgAuthenSecondString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The second TACACS+ authentication string." ::= { agTacacsConfig 17 } tacNewCfgAuthenSecondString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The second TACACS+ authentication string." ::= { agTacacsConfig 18 } tacCurCfgCmdAuthor OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable TACACS+ command authorization." ::= { agTacacsConfig 19 } tacNewCfgCmdAuthor OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable TACACS+ command authorization." ::= { agTacacsConfig 20 } tacCurCfgCmdLogging OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable TACACS+ command logging." ::= { agTacacsConfig 21 } tacNewCfgCmdLogging OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable TACACS+ command logging." ::= { agTacacsConfig 22 } tacCurCfgSecBd OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable TACACS+ secure backdoor for telnet." ::= { agTacacsConfig 23 } tacNewCfgSecBd OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable TACACS+ secure backdoor for telnet." ::= { agTacacsConfig 24 } tacCurCfgCmap OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/Disable Tacacs+ new privilege level mapping, as configured in the current configuration block." ::= { agTacacsConfig 25 } tacNewCfgCmap OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Tacacs+ new privilege level mapping." ::= { agTacacsConfig 26 } tacCurCfgEnaPassChange OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " Enable/Disable Tacacs+ password change." ::= { agTacacsConfig 29 } tacNewCfgEnaPassChange OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION " Enable/Disable Tacacs+ password change." ::= { agTacacsConfig 30 } tacChangePassForUser OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The username for changing server password." ::= { agTacacsConfig 31 } tacChangePassCurPass OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The current password for tacacs server." ::= { agTacacsConfig 32 } tacChangePassNewPass OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The new password for tacacs server." ::= { agTacacsConfig 33 } tacChangePassForServer OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Change password for <1/2> Tacacs+ server." ::= { agTacacsConfig 34 } agTacacsUserMapCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AgTacacsUserMapCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of tacacs+ user map current configuration." ::= { agTacacsConfig 39 } agTacacsUserMapCurCfgTableEntry OBJECT-TYPE SYNTAX AgTacacsUserMapCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the tacacs+ user mapping table." INDEX { agTacacsUserMapCurCfgUId } ::= { agTacacsUserMapCurCfgTable 1 } AgTacacsUserMapCurCfgTableEntry ::= SEQUENCE { agTacacsUserMapCurCfgUId Integer32, agTacacsUserMapCurCfgMapping INTEGER } agTacacsUserMapCurCfgUId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current config remote privilege identifier. The identifier value corresponds to the remote privilege." ::= { agTacacsUserMapCurCfgTableEntry 1 } agTacacsUserMapCurCfgMapping OBJECT-TYPE SYNTAX INTEGER { none(0), user(1), oper(2), admin(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current Tacacs+ user privilege mappings. The correspondence between the local privilege and the remote privilege is: - The remote privilege is the privilege identifier value - The local privilege is the mapped value(user, oper, admin) Example: For the remote privilege 15, we have the index 16: agTacacsUserMapCurCfgUId.16 = 15." ::= { agTacacsUserMapCurCfgTableEntry 2 } agTacacsUserMapNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AgTacacsUserMapNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of tacacs+ user map new configuration." ::= { agTacacsConfig 40 } tacNewCfgDirectedRequest OBJECT-TYPE SYNTAX INTEGER { disabled(1), restricted(2), no-truncate(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable tacacs directed request." ::= { agTacacsConfig 41 } tacCurCfgDirectedRequest OBJECT-TYPE SYNTAX INTEGER { disabled(1), restricted(2), no-truncate(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current tacacs directed request state." ::= { agTacacsConfig 42 } agTacacsUserMapNewCfgTableEntry OBJECT-TYPE SYNTAX AgTacacsUserMapNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the tacacs+ user mapping table." INDEX { agTacacsUserMapNewCfgUId } ::= { agTacacsUserMapNewCfgTable 1 } AgTacacsUserMapNewCfgTableEntry ::= SEQUENCE { agTacacsUserMapNewCfgUId Integer32, agTacacsUserMapNewCfgMapping INTEGER } agTacacsUserMapNewCfgUId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The new config remote privilege identifier. The identifier value corresponds to the remote privilege." ::= { agTacacsUserMapNewCfgTableEntry 1 } agTacacsUserMapNewCfgMapping OBJECT-TYPE SYNTAX INTEGER { none(0), user(1), oper(2), admin(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set new Tacacs+ user privilege mappings. The correspondence between the local privilege and the remote privilege is: - The remote privilege is the privilege identifier value - The local privilege is the mapped value(user, oper, admin) Example: For the remote privilege 15, we have the index 16: agTacacsUserMapNewCfgUId.16 = 15." ::= { agTacacsUserMapNewCfgTableEntry 2 } tacCurCfgAttempts OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of login attempts to the TACACS+ server." ::= { agTacacsConfig 43 } tacNewCfgAttempts OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of login attempts to the TACACS+ server." ::= { agTacacsConfig 44 } tacCurBypassEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of the enable bypass.If the status of this object is enabled, user authenticated via TACACS+ with admin previllage is granted enable previllage access.If disabled, admin users will be provided with enable previllage access based on enable password configured." DEFVAL { enable } ::= { agTacacsConfig 45 } tacNewBypassEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Status of the enable bypass.If the status of this object is enabled, user authenticated via TACACS+ with admin previllage is granted enable previllage access.If disabled, admin users will be provided with enable previllage access based on enable password configured." DEFVAL { enable } ::= { agTacacsConfig 46 } tacCurCfgEnableAccounting OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0) } MAX-ACCESS read-only STATUS current DESCRIPTION " Current TACACS+ accounting state." ::= { agTacacsConfig 47 } tacNewCfgEnableAccounting OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(0) } MAX-ACCESS read-write STATUS current DESCRIPTION " Enable/Disable TACACS+ accounting." ::= { agTacacsConfig 48 } tacCurCfgSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the loopback interface that should be used for the source IP of the Tacacs+ message; 0 means that no loopback interface is used as the source of the Tacacs+ message." ::= { agTacacsConfig 49 } tacNewCfgSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The index of the loopback interface that should be used for the source IP of the Tacacs+ message; 0 means that no loopback interface is used as the source of the Tacacs+ message." ::= { agTacacsConfig 50 } -- Multiple Management network MIB objects agMgmtNetTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in the Management Network Table." ::= { agMgmtNetConfig 1 } agCurCfgMgmtNetTable OBJECT-TYPE SYNTAX SEQUENCE OF AgCurCfgMgmtNetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for Management Network definitions in the current configuration block." ::= { agMgmtNetConfig 2 } agCurCfgMgmtNetEntry OBJECT-TYPE SYNTAX AgCurCfgMgmtNetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the management network definition table." INDEX { agCurCfgMgmtNetIndex } ::= { agCurCfgMgmtNetTable 1 } AgCurCfgMgmtNetEntry ::= SEQUENCE { agCurCfgMgmtNetIndex Integer32, agCurCfgMgmtNetSubnet DisplayString, agCurCfgMgmtNetMask DisplayString } agCurCfgMgmtNetIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the Management Network Definition table." ::= { agCurCfgMgmtNetEntry 1 } agCurCfgMgmtNetSubnet OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Management Network Address in the current configuration block." ::= { agCurCfgMgmtNetEntry 2 } agCurCfgMgmtNetMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Management Network Mask/Prefix Length in the current configuration block." ::= { agCurCfgMgmtNetEntry 3 } agNewCfgMgmtNetTable OBJECT-TYPE SYNTAX SEQUENCE OF AgNewCfgMgmtNetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for Management Network definitions in the new configuration block." ::= { agMgmtNetConfig 3 } agNewCfgMgmtNetEntry OBJECT-TYPE SYNTAX AgNewCfgMgmtNetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the management network definition table." INDEX { agNewCfgMgmtNetIndex } ::= { agNewCfgMgmtNetTable 1 } AgNewCfgMgmtNetEntry ::= SEQUENCE { agNewCfgMgmtNetIndex Integer32, agNewCfgMgmtNetSubnet DisplayString, agNewCfgMgmtNetMask DisplayString, agNewCfgMgmtNetDelete INTEGER } agNewCfgMgmtNetIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the Management Network Definition table." ::= { agNewCfgMgmtNetEntry 1 } agNewCfgMgmtNetSubnet OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The Management Network Address in the new configuration block." ::= { agNewCfgMgmtNetEntry 2 } agNewCfgMgmtNetMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The Management Network Mask/Prefix length in the new configuration block." ::= { agNewCfgMgmtNetEntry 3 } agNewCfgMgmtNetDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "By setting the value to delete(2), the entire row is deleted." ::= { agNewCfgMgmtNetEntry 4 } agMgmtNetClear OBJECT-TYPE SYNTAX INTEGER { other(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "By setting the value to delete(2), the entire table is cleared." ::= { agMgmtNetConfig 4 } -- Scheduled Reboot Group agCfgBootResetParameters OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "String formatated as 'weekday hour minute' where - weekday is none(0),sunday(1),monday(2), tuesday(3),wednesday(4),thursday(5),friday(6), saturday(7) - hour is the hour in 24-hour format for reboot - minutes are the minutes [00] for reboot" ::= { agBoot 1 } agCfgBootReset OBJECT-TYPE SYNTAX INTEGER { none(1), cancel(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Cancel pending switch reset." ::= { agBoot 4 } agCfgBootNxtResetTime OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "Display the next scheduled reboot time." ::= { agBoot 5 } agCfgBootPendingReset OBJECT-TYPE SYNTAX INTEGER { idle(1), pending(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Shows if there is any pending reboot scheduled. You should cancel any pending reboot scheduled before setting another." ::= { agBoot 6 } agAccessUserMaxUserID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of User IDs." ::= { agAccess 1 } agAccessCurStrongPassword OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of strong password." ::= { agAccess 4 } agAccessNewStrongPassword OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to enabled(1) enables strong password support, while disabled(0) disables it." ::= { agAccess 5 } agAccessCurStrongPassValidity OBJECT-TYPE SYNTAX INTEGER (1..365) MAX-ACCESS read-only STATUS current DESCRIPTION "Password validity in days." ::= { agAccess 6 } agAccessNewStrongPassValidity OBJECT-TYPE SYNTAX INTEGER (1..365) MAX-ACCESS read-write STATUS current DESCRIPTION "Get or set password validity in days." ::= { agAccess 7 } agAccessCurStrongPassWarning OBJECT-TYPE SYNTAX INTEGER (1..365) MAX-ACCESS read-only STATUS current DESCRIPTION "Warning days before password expires." ::= { agAccess 8 } agAccessNewStrongPassWarning OBJECT-TYPE SYNTAX INTEGER (1..365) MAX-ACCESS read-write STATUS current DESCRIPTION "Get or set warning days before password expires." ::= { agAccess 9 } agAccessCurStrongPassFailLog OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of failed logins that trigger security notifications." ::= { agAccess 10 } agAccessNewStrongPassFailLog OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Get or set number of failed logins that trigger security notifications." ::= { agAccess 11 } agAccessCurDefaultAdmin OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Get default admin account state. (1) indicates enabled and (0) indicates disabled (0). Default it is enabled." ::= { agAccess 12 } agAccessNewDefaultAdmin OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to enabled (1) will enable the default admin account while disabled (0) will disable the default admin account. Default it is enabled." ::= { agAccess 13 } agAccessCurStrongPassLockout OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of Lockout" ::= { agAccess 14 } agAccessNewStrongPassLockout OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to enabled (1) enables account locking after trying for failed login attempts. While disabled (0) disables account locking." ::= { agAccess 15 } agAccessCurStrongPassAttemptsMaxFail OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of failed logins before disabling account. Default value is 6" ::= { agAccess 16 } agAccessNewStrongPassAttemptsMaxFail OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Sets Max number of failed logins before disabling account. Default value is 6" ::= { agAccess 17 } agAccessUserCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AgAccessUserCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Access user configuration." ::= { agAccess 2 } agAccessUserCurCfgTableEntry OBJECT-TYPE SYNTAX AgAccessUserCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Access user configuration table." INDEX { agAccessUserCurCfgUId } ::= { agAccessUserCurCfgTable 1 } AgAccessUserCurCfgTableEntry ::= SEQUENCE { agAccessUserCurCfgUId Integer32, agAccessUserCurCos INTEGER, agAccessUserCurCfgName DisplayString, agAccessUserCurCfgPswd DisplayString, agAccessUserCurCfgState INTEGER } agAccessUserCurCfgUId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The User identifier." ::= { agAccessUserCurCfgTableEntry 1 } agAccessUserCurCos OBJECT-TYPE SYNTAX INTEGER { user(0), oper(3), admin(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The user class of service." ::= { agAccessUserCurCfgTableEntry 2 } agAccessUserCurCfgName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The user name. Please note, the max length is 8 in stacking mode." ::= { agAccessUserCurCfgTableEntry 3 } agAccessUserCurCfgPswd OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The character string representing the user password." ::= { agAccessUserCurCfgTableEntry 4 } agAccessUserCurCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "User validation (enabled or disabled) in current configuration block." ::= { agAccessUserCurCfgTableEntry 6 } agAccessUserNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AgAccessUserNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Access user configuration." ::= { agAccess 3 } agAccessUserNewCfgTableEntry OBJECT-TYPE SYNTAX AgAccessUserNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Access user configuration table." INDEX { agAccessUserNewCfgUId } ::= { agAccessUserNewCfgTable 1 } AgAccessUserNewCfgTableEntry ::= SEQUENCE { agAccessUserNewCfgUId Integer32, agAccessUserNewCos INTEGER, agAccessUserNewCfgName DisplayString, agAccessUserNewCfgPswd DisplayString, agAccessUserNewCfgState INTEGER, agAccessUserNewCfgDelete INTEGER } agAccessUserNewCfgUId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The User identifier." ::= { agAccessUserNewCfgTableEntry 1 } agAccessUserNewCos OBJECT-TYPE SYNTAX INTEGER { user(0), oper(3), admin(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "The user class of service." ::= { agAccessUserNewCfgTableEntry 2 } agAccessUserNewCfgName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "The user name. Please note, the max length is 8 in stacking mode." ::= { agAccessUserNewCfgTableEntry 3 } agAccessUserNewCfgPswd OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "The character string representing the user password." ::= { agAccessUserNewCfgTableEntry 4 } agAccessUserNewCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "User validation (enabled or disabled) in new configuration block." ::= { agAccessUserNewCfgTableEntry 7 } agAccessUserNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This is an action object to create or delete a User. other(1) is returned always when read. The following values are writable: delete(2)...to delete a User" ::= { agAccessUserNewCfgTableEntry 8 } -- LDAP Configuration ldapCurCfgPrimaryIpAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the Primary LDAP server,it can be an ipv4 or ipv6 address." ::= { agLdapConfig 1 } ldapNewCfgPrimaryIpAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the Primary LDAP server,it can be an ipv4 or ipv6 address." ::= { agLdapConfig 2 } ldapCurCfgSecondaryIpAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the Secondary LDAP server,it can be an ipv4 or ipv6 address." ::= { agLdapConfig 3 } ldapNewCfgSecondaryIpAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the Secondary LDAP server,it can be an ipv4 or ipv6 address." ::= { agLdapConfig 4 } ldapCurCfgPort OBJECT-TYPE SYNTAX INTEGER (1..65000) MAX-ACCESS read-only STATUS current DESCRIPTION "Specify the LDAP port number." ::= { agLdapConfig 5 } ldapNewCfgPort OBJECT-TYPE SYNTAX INTEGER (1..65000) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the LDAP port number." ::= { agLdapConfig 6 } ldapCurCfgRetries OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of retries to the LDAP server." ::= { agLdapConfig 7 } ldapNewCfgRetries OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of retries to the LDAP server." ::= { agLdapConfig 8 } ldapCurCfgTimeout OBJECT-TYPE SYNTAX INTEGER (4..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of seconds before resending authentication to LDAP server." ::= { agLdapConfig 9 } ldapNewCfgTimeout OBJECT-TYPE SYNTAX INTEGER (4..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of seconds before resending authentication to LDAP server." ::= { agLdapConfig 10 } ldapCurCfgDomain OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The LDAP domain name." ::= { agLdapConfig 11 } ldapNewCfgDomain OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-write STATUS current DESCRIPTION "The LDAP domain name." ::= { agLdapConfig 12 } ldapCurCfgBackdoor OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable LDAP backdoor for telnet/ssh/http/https." ::= { agLdapConfig 13 } ldapNewCfgBackdoor OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable LDAP backdoor for telnet/ssh/http/https." ::= { agLdapConfig 14 } ldapCurCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable LDAP authentication." ::= { agLdapConfig 15 } ldapNewCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable LDAP authentication." ::= { agLdapConfig 16 } ldapCurCfgUserNameAttribute OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The LDAP username attribute." ::= { agLdapConfig 21 } ldapNewCfgUserNameAttribute OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-write STATUS current DESCRIPTION "The LDAP username attribute (default = uid)." ::= { agLdapConfig 22 } -- sFlow Group sflowCurCfgServerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the sFlow server." ::= { agsFlowConfig 1 } sflowNewCfgServerAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(0..46)) MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the sFlow server." ::= { agsFlowConfig 2 } sflowCurCfgServerPort OBJECT-TYPE SYNTAX INTEGER (1..65000) MAX-ACCESS read-only STATUS current DESCRIPTION "Specify the sFlow server port number." ::= { agsFlowConfig 3 } sflowNewCfgServerPort OBJECT-TYPE SYNTAX INTEGER (1..65000) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the sFlow server port number." ::= { agsFlowConfig 4 } sflowCurCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable sFlow." ::= { agsFlowConfig 5 } sflowNewCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable sFlow" ::= { agsFlowConfig 6 } sflowCurPortCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF SflowCurPortCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of sFlow port configuration." ::= { agsFlowConfig 7 } sflowCurPortCfgTableEntry OBJECT-TYPE SYNTAX SflowCurPortCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the sFlow port configuration table." INDEX { sflowCurPortCfgTableId } ::= { sflowCurPortCfgTable 1 } SflowCurPortCfgTableEntry ::= SEQUENCE { sflowCurPortCfgTableId PortNumber, sflowCurPortSampling INTEGER, sflowCurPortPolling INTEGER } sflowCurPortCfgTableId OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "sFlow port number." ::= { sflowCurPortCfgTableEntry 1 } sflowCurPortSampling OBJECT-TYPE SYNTAX INTEGER (256..65536) MAX-ACCESS read-only STATUS current DESCRIPTION "The current sFlow port sampling rate." ::= { sflowCurPortCfgTableEntry 2 } sflowCurPortPolling OBJECT-TYPE SYNTAX INTEGER (5..60) MAX-ACCESS read-only STATUS current DESCRIPTION "The current sFlow port polling interval." ::= { sflowCurPortCfgTableEntry 3 } sflowNewPortCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF SflowNewPortCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of sFlow port configuration." ::= { agsFlowConfig 8 } sflowNewPortCfgTableEntry OBJECT-TYPE SYNTAX SflowNewPortCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the sFlow port configuration table." INDEX { sflowNewPortCfgTableId } ::= { sflowNewPortCfgTable 1 } SflowNewPortCfgTableEntry ::= SEQUENCE { sflowNewPortCfgTableId PortNumber, sflowNewPortSampling INTEGER, sflowNewPortPolling INTEGER } sflowNewPortCfgTableId OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION " sFlow port number." ::= { sflowNewPortCfgTableEntry 1 } sflowNewPortSampling OBJECT-TYPE SYNTAX INTEGER (256..65536) MAX-ACCESS read-write STATUS current DESCRIPTION "The new sFlow port sampling rate. Valid range: 256-65536| 0 for disable" ::= { sflowNewPortCfgTableEntry 2 } sflowNewPortPolling OBJECT-TYPE SYNTAX INTEGER (5..60) MAX-ACCESS read-write STATUS current DESCRIPTION "The new sFlow port polling interval. Valid range: 5-60| 0 for disable" ::= { sflowNewPortCfgTableEntry 3 } -- USB Copy agUSBoperation OBJECT-TYPE SYNTAX INTEGER { fromUSB(1), toUSB(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set operation: fromUSB(1): from USB to Flash toUSB(2): from Flash to USB" ::= { agUSBCopy 1 } agUSBfile OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-write STATUS current DESCRIPTION "USB filename (to copy from or to copy to)" ::= { agUSBCopy 2 } agUSBflashFile OBJECT-TYPE SYNTAX INTEGER { boot(1), image1(2), active(3), syslog(4), crashdump(5), image2(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set flash file involved (boot image, image 1, active configuration, syslog, crashdump). Syslog and crashdump can only be copied to USB. (it is forbidden to copy from USB to flash) " ::= { agUSBCopy 3 } agUSBcopyFile OBJECT-TYPE SYNTAX INTEGER { copy(1), idle(2), inprogress(3), complete(4), failed(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "When this object is read the current state is returned. idle(1) indicates that there is no copy in progess. complete(4) indicates that the last copy operation is completed. Setting the value to copy(1), will execute the operation (copy to or from USB stick). If the copy is successful this variable will return the state 'complete' else it will return 'failed'. Once the operation is completed, agUSBcopyFile should be set back to 'idle' state so others can issue the copy command via SNMP." ::= { agUSBCopy 4 } agUSBresult OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "Last USB Copy action result." ::= { agUSBCopy 5 } -- Statistics Group -- Packet Statistics Group -- This group represents Packet Statistics information pktStatsAllocs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packet allocations from the packet buffer pool by the TCP/IP protocol stack." ::= { pktStats 1 } pktStatsFrees OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of times the packet buffers are freed(released) to the packet buffer pool by the TCP/IP protocol stack." ::= { pktStats 2 } pktStatsAllocFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packet allocation failures from the packet buffer pool by the TCP/IP protocol stack." ::= { pktStats 3} pktStatsMediums OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packet allocations with size greater than 128 bytes and less than or equal to 1536 bytes from the packet buffer pool by the TCP/IP protocol stack." ::= { pktStats 4} pktStatsJumbos OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packet allocations with size larger than 1536 bytes from the packet buffer pool by the TCP/IP protocol stack." ::= { pktStats 5} pktStatsSmalls OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packet allocations with size less than or eqaul to 128 bytes from the packet buffer pool by the TCP/IP protocol stack." ::= { pktStats 6} pktStatsMediumsHiWatermark OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The highest number of packet allocations with size greater than 128 bytes and less than or equal to 1536 bytes from the packet buffer pool by the TCP/IP protocol stack." ::= { pktStats 7} pktStatsJumbosHiWatermark OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The highest number of packet allocations with size larger than 1536 bytes from the packet buffer pool by the TCP/IP protocol stack." ::= { pktStats 8} pktStatsSmallsHiWatermark OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The highest number of packet allocations with size less than or equal to 128 bytes from the packet buffer pool by the TCP/IP protocol stack." ::= { pktStats 9} -- MP CPU Statisitics Group mpCpuStatsUtil1Second OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The utilization of MP CPU over 1 second. It shows the percentage." ::= { mpCpuStats 1 } mpCpuStatsUtil5Seconds OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The utilization of MP CPU over 5 seconds. It shows the percentage." ::= { mpCpuStats 2 } mpCpuStatsUtil1Minute OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The utilization of MP CPU over 1 minute. It shows the percentage." ::= { mpCpuStats 3 } mpCpuStatsUtil5Minutes OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The utilization of MP CPU over 5 minutes. It shows the percentage." ::= { mpCpuStats 6 } -- Stats for per thread CPU utilization cpuUtilProcessStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CpuUtilProcessStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of CPU utilization per process statistics." ::= { mpCpuStats 5 } cpuUtilProcessStatsTableEntry OBJECT-TYPE SYNTAX CpuUtilProcessStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the CPU utilization stats per process table." INDEX { processId } ::= { cpuUtilProcessStatsTable 1 } CpuUtilProcessStatsTableEntry ::= SEQUENCE { processId Integer32, processName DisplayString, cpuProcessUtil1Sec DisplayString, cpuProcessUtil5Sec DisplayString, cpuProcessUtil1Min DisplayString, cpuProcessUtil5Min DisplayString, processStatus DisplayString } processId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The process ID." ::= { cpuUtilProcessStatsTableEntry 1 } processName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Process Name." ::= { cpuUtilProcessStatsTableEntry 2 } cpuProcessUtil1Sec OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The utilization of MP CPU over 1 second. It shows the percentage." ::= { cpuUtilProcessStatsTableEntry 3 } cpuProcessUtil5Sec OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The utilization of MP CPU over 5 seconds. It shows the percentage." ::= { cpuUtilProcessStatsTableEntry 4 } cpuProcessUtil1Min OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The utilization of MP CPU over 1 min. It shows the percentage." ::= { cpuUtilProcessStatsTableEntry 5 } cpuProcessUtil5Min OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The utilization of MP CPU over 5 min. It shows the percentage." ::= { cpuUtilProcessStatsTableEntry 6 } processStatus OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Process Status" ::= { cpuUtilProcessStatsTableEntry 7 } -- -- Port statistics table -- portStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF PortStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of port statistics." ::= { portStats 1 } portStatsTableEntry OBJECT-TYPE SYNTAX PortStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the port stats table." INDEX { portStatsIndx } ::= { portStatsTable 1 } PortStatsTableEntry ::= SEQUENCE { portStatsIndx PortNumber, portStatsPhyIfInOctets Counter32, portStatsPhyIfInUcastPkts Counter32, portStatsPhyIfInNUcastPkts Counter32, portStatsPhyIfInDiscards Counter32, portStatsPhyIfInErrors Counter32, portStatsPhyIfInUnknownProtos Counter32, portStatsPhyIfOutOctets Counter32, portStatsPhyIfOutUcastPkts Counter32, portStatsPhyIfOutNUcastPkts Counter32, portStatsPhyIfOutDiscards Counter32, portStatsPhyIfOutErrors Counter32, portStatsPhyIfOutQLen Gauge32, portStatsPhyIfInBroadcastPkts Counter32, portStatsPhyIfOutBroadcastPkts Counter32, portStatsPhyIfInMulticastPkts Counter32, portStatsPhyIfOutMulticastPkts Counter32, portStatsClear INTEGER ,portStatsLinkStateChange Counter32 ,portStatsPhyIfInFctlPkts Counter32 ,portStatsPhyIfOutFctlPkts Counter32 ,portStatsPhyIfInFctlPktsRate Counter32 ,portStatsPhyIfOutFctlPktsRate Counter32 ,portStatsPhyIfIngDiscdVlan Counter32 ,portStatsPhyIfIngDiscdEgrMap Counter32 ,portStatsPhyIfIngDiscdFilter Counter32 ,portStatsPhyIfIngDiscdPolicy Counter32 ,portStatsPhyIfIngDiscdNonFwdStat Counter32 ,portStatsPhyIfIngDiscdIbpCbp Counter32 ,portStatsDot1PortInFrames Counter32 ,portStatsDot1PortOutFrames Counter32 ,portStatsDot1PortInDiscards Counter32 ,portStatsDot1TpLearnedEntryDiscards Counter32 ,portStatsDot1StpPortForwardTransitions Counter32 ,portStatsPhyIfEgrHOLBlockDiscd Counter32 ,portStatsPhyIfEgrMMUDiscd Counter32 ,portStatsPhyIfEgrCellErrDiscd Counter32 ,portStatsPhyIfEgrMMUAgeDiscd Counter32 ,portStatsPhyIfEgrOtherDiscd Counter32 } tcpControlBlocksTable OBJECT-TYPE SYNTAX SEQUENCE OF TcpControlBlocksTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "All TCP allocated control blocks " ::= { mpTcbStats 1 } tcpControlBlocksTableEntry OBJECT-TYPE SYNTAX TcpControlBlocksTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the TCP control blocks table. " INDEX { tcpControlBlocksIndx } ::= { tcpControlBlocksTable 1 } TcpControlBlocksTableEntry ::= SEQUENCE { tcpControlBlocksIndx Integer32, destAddr DisplayString, remotePort Gauge32, sourceAddr DisplayString, localPort Gauge32, state DisplayString } tcpControlBlocksIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP blocks index." ::= { tcpControlBlocksTableEntry 1 } destAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP block destination address." ::= { tcpControlBlocksTableEntry 2 } remotePort OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Tcp informations concerning the remote port" ::= { tcpControlBlocksTableEntry 3} sourceAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "IP address of the source of the Tcp block" ::= { tcpControlBlocksTableEntry 4} localPort OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Tcp informations concerning the local port" ::= { tcpControlBlocksTableEntry 5} state OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the Tcp" ::= { tcpControlBlocksTableEntry 6 } udpControlBlocksTable OBJECT-TYPE SYNTAX SEQUENCE OF UdpControlBlocksTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "All UDP control blocks in use" ::= { mpUdpStats 1 } udpControlBlocksTableEntry OBJECT-TYPE SYNTAX UdpControlBlocksTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the UDP control blocks table. " INDEX { udpMpLocalPort } ::= { udpControlBlocksTable 1 } UdpControlBlocksTableEntry ::= SEQUENCE { udpMpLocalPort Integer32, udpMpState DisplayString } udpMpLocalPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current UDP local port." ::= { udpControlBlocksTableEntry 1 } udpMpState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " The port's state. " ::= { udpControlBlocksTableEntry 2 } portStatsIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port index." ::= { portStatsTableEntry 1 } portStatsPhyIfInOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets received on the interface, including framing characters." ::= { portStatsTableEntry 2 } portStatsPhyIfInUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of subnetwork-unicast packets delivered to a higher-layer protocol." ::= { portStatsTableEntry 3 } portStatsPhyIfInNUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol." ::= { portStatsTableEntry 4 } portStatsPhyIfInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space." ::= { portStatsTableEntry 5 } portStatsPhyIfInErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol." ::= { portStatsTableEntry 6 } portStatsPhyIfInUnknownProtos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets received via the interface which were discarded because of an unknown or unsupported protocol." ::= { portStatsTableEntry 7 } portStatsPhyIfOutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of octets transmitted out of the interface, including framing characters." ::= { portStatsTableEntry 8 } portStatsPhyIfOutUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent." ::= { portStatsTableEntry 9 } portStatsPhyIfOutNUcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent." ::= { portStatsTableEntry 10 } portStatsPhyIfOutDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space." ::= { portStatsTableEntry 11 } portStatsPhyIfOutErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of outbound packets that could not be transmitted because of errors." ::= { portStatsTableEntry 12 } portStatsPhyIfOutQLen OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The length of the output packet queue (in packets)." ::= { portStatsTableEntry 13 } portStatsPhyIfInBroadcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer." ::= { portStatsTableEntry 14 } portStatsPhyIfOutBroadcastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent." ::= { portStatsTableEntry 15 } portStatsPhyIfInMulticastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer." ::= { portStatsTableEntry 17 } portStatsPhyIfOutMulticastPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent." ::= { portStatsTableEntry 18 } portStatsClear OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the stats for this port." ::= { portStatsTableEntry 16 } portStatsLinkStateChange OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of link state changes." ::= { portStatsTableEntry 20 } portStatsPhyIfInFctlPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of inbound flow control packets." ::= { portStatsTableEntry 21 } portStatsPhyIfOutFctlPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of outbound flow control packets." ::= { portStatsTableEntry 22 } portStatsPhyIfInFctlPktsRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of inbound flow control packets per second." ::= { portStatsTableEntry 23 } portStatsPhyIfOutFctlPktsRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of outbound flow control packets per second." ::= { portStatsTableEntry 24 } portStatsPhyIfIngDiscdVlan OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, discarded because of VLAN." ::= { portStatsTableEntry 25 } portStatsPhyIfIngDiscdEgrMap OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, discarded because of empty egress portmap." ::= { portStatsTableEntry 26 } portStatsPhyIfIngDiscdFilter OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, discarded because of filter." ::= { portStatsTableEntry 27 } portStatsPhyIfIngDiscdPolicy OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, discarded because of policy." ::= { portStatsTableEntry 28 } portStatsPhyIfIngDiscdNonFwdStat OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, discarded because of Non-Forwarding State." ::= { portStatsTableEntry 29 } portStatsPhyIfIngDiscdIbpCbp OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets discarded because of IBP/CBP." ::= { portStatsTableEntry 30 } portStatsDot1PortInFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IN frames per port." ::= { portStatsTableEntry 31 } portStatsDot1PortOutFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OUT frames per port." ::= { portStatsTableEntry 32 } portStatsDot1PortInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IN packets discarded per port." ::= { portStatsTableEntry 33 } portStatsDot1TpLearnedEntryDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Dot1Tp learned entries discarded." ::= { portStatsTableEntry 34 } portStatsDot1StpPortForwardTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transitions ...." ::= { portStatsTableEntry 35 } portQoSCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF PortQoSCounterTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table for QoS counters." ::= { portStats 9 } portQoSCounterTableEntry OBJECT-TYPE SYNTAX PortQoSCounterTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the port QoS table." INDEX { portQoSIndex, queueQoSIndex } ::= { portQoSCounterTable 1 } PortQoSCounterTableEntry ::= SEQUENCE { portQoSIndex PortNumber, queueQoSIndex Integer32, txPackets Counter64, droppedPackets Counter64, txBytes Counter64, droppedBytes Counter64, txPacketsRate Counter64, droppedPacketsRate Counter64, txBytesRate Counter64, droppedBytesRate Counter64 } portQoSIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port" ::= { portQoSCounterTableEntry 1 } queueQoSIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the queue per port." ::= { portQoSCounterTableEntry 2 } txPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total Tx packets." ::= { portQoSCounterTableEntry 3 } droppedPackets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The dropped packets." ::= { portQoSCounterTableEntry 4 } txBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total Tx bytes." ::= { portQoSCounterTableEntry 5 } droppedBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The dropped bytes." ::= { portQoSCounterTableEntry 6 } txPacketsRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The Tx packets rate." ::= { portQoSCounterTableEntry 7 } droppedPacketsRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The dropped packets rate." ::= { portQoSCounterTableEntry 8 } txBytesRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The Tx bytes rate." ::= { portQoSCounterTableEntry 9 } droppedBytesRate OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The dropped bytes rate." ::= { portQoSCounterTableEntry 10 } portStatsPhyIfEgrHOLBlockDiscd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, discarded because of HOL Blocking." ::= { portStatsTableEntry 36 } portStatsPhyIfEgrMMUDiscd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, discarded by MMU because of zero port bitmap." ::= { portStatsTableEntry 37 } portStatsPhyIfEgrCellErrDiscd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, discarded because of Cell Errors or purging." ::= { portStatsTableEntry 38 } portStatsPhyIfEgrMMUAgeDiscd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, discarded because of MMU Aging. Applicable in 10/100 mode, incremented for frames aborted which were deferred for an excessive period of time." ::= { portStatsTableEntry 39 } portStatsPhyIfEgrOtherDiscd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets, discarded because of Other reasons." ::= { portStatsTableEntry 40 } allportsStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AllportsStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of all ports statistics." ::= { portStats 4 } allportsStatsTableEntry OBJECT-TYPE SYNTAX AllportsStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of all ports statistics." INDEX { allportsStatsIndx } ::= { allportsStatsTable 1 } AllportsStatsTableEntry ::= SEQUENCE { allportsStatsIndx PortNumber, allportsStatsDescr DisplayString, allportsStatsSpeed INTEGER, allportsStatsPhysAddress PhysAddress, allportsStatsAdminStatus INTEGER, allportsStatsOperStatus INTEGER, allportsStatsInOctets Counter32, allportsStatsOutOctets Counter32, allportsStatsInPkts Counter32, allportsStatsOutPkts Counter32, allportsStatsInUcast DisplayString, allportsStatsOutUcast DisplayString, allportsStatsInBcast DisplayString, allportsStatsOutBcast DisplayString, allportsStatsInMcast DisplayString, allportsStatsOutMcast DisplayString, allportsStatsInDiscards Counter32, allportsStatsOutDiscards Counter32, allportsStatsInErrors Counter32, allportsStatsOutErrors Counter32, allportsStatsInUnknownProtos DisplayString, allportsStatsOutQLen DisplayString , allportsStatsipInReceives Counter32, allportsStatsipInHeaderErrors Counter32, allportsStatsipInDiscards Counter32 , allportsStatsipInReceivesRate Counter32, allportsStatsipInHeaderErrorsRate Counter32, allportsStatsipInDiscardsRate Counter32 , allportsStatsLinkStateChange Counter32 , allportsStatsInOctetsRate Counter32, allportsStatsOutOctetsRate Counter32, allportsStatsInUcastRate DisplayString, allportsStatsOutUcastRate DisplayString, allportsStatsInBcastRate DisplayString, allportsStatsOutBcastRate DisplayString, allportsStatsInMcastRate DisplayString, allportsStatsOutMcastRate DisplayString, allportsStatsInDiscardsRate Counter32, allportsStatsOutDiscardsRate Counter32, allportsStatsInErrorsRate Counter32, allportsStatsOutErrorsRate Counter32 } allportsStatsIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port number." ::= { allportsStatsTableEntry 1 } allportsStatsDescr OBJECT-TYPE SYNTAX DisplayString(SIZE(0..7)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port description." ::= { allportsStatsTableEntry 2 } allportsStatsSpeed OBJECT-TYPE SYNTAX INTEGER { mbs10(2), mbs100(3), mbs1000(4), any(5) , mbs10000(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational speed of the port." ::= { allportsStatsTableEntry 3 } allportsStatsPhysAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The port MAC Address." ::= { allportsStatsTableEntry 4 } allportsStatsAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), testing(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port Admin state." ::= { allportsStatsTableEntry 5 } allportsStatsOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), testing(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port Operational Status." ::= { allportsStatsTableEntry 6 } allportsStatsInOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Octets In for port." ::= { allportsStatsTableEntry 7 } allportsStatsOutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Octets Out for port." ::= { allportsStatsTableEntry 8 } allportsStatsInPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Packets In for port." ::= { allportsStatsTableEntry 9 } allportsStatsOutPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Packets Out for port." ::= { allportsStatsTableEntry 10 } allportsStatsInUcast OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Unicast Packets In for port." ::= { allportsStatsTableEntry 11 } allportsStatsOutUcast OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Unicast Packets Out for port." ::= { allportsStatsTableEntry 12 } allportsStatsInBcast OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Broadcasts Packets In for port." ::= { allportsStatsTableEntry 13 } allportsStatsOutBcast OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Broadcasts Packets Out for port." ::= { allportsStatsTableEntry 14 } allportsStatsInMcast OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast Packets In for port." ::= { allportsStatsTableEntry 15 } allportsStatsOutMcast OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast Packets Out for port." ::= { allportsStatsTableEntry 16 } allportsStatsInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Discarded Packets for port." ::= { allportsStatsTableEntry 17 } allportsStatsOutDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Outbound Packets for port." ::= { allportsStatsTableEntry 18 } allportsStatsInErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Error Packets for port." ::= { allportsStatsTableEntry 19 } allportsStatsOutErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Not sent packets due to error." ::= { allportsStatsTableEntry 20 } allportsStatsInUnknownProtos OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Unknown protocol packets." ::= { allportsStatsTableEntry 21 } allportsStatsOutQLen OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Outbound Packet Queue Length." ::= { allportsStatsTableEntry 22 } allportsStatsipInReceives OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ip In Receives." ::= { allportsStatsTableEntry 23 } allportsStatsipInHeaderErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ip In Header Errors." ::= { allportsStatsTableEntry 24 } allportsStatsipInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ip In Discards." ::= { allportsStatsTableEntry 25 } allportsStatsLinkStateChange OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of link state changes." ::= { allportsStatsTableEntry 26 } allportsStatsipInReceivesRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ip In Receives rate." ::= { allportsStatsTableEntry 27 } allportsStatsipInHeaderErrorsRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ip In Header Errors rate." ::= { allportsStatsTableEntry 28 } allportsStatsipInDiscardsRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Ip In Discards rate." ::= { allportsStatsTableEntry 29 } allportsStatsInOctetsRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Octets In rate for port." ::= { allportsStatsTableEntry 30 } allportsStatsOutOctetsRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Octets Out rate for port." ::= { allportsStatsTableEntry 31 } allportsStatsInUcastRate OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Unicast Packets In rate for port." ::= { allportsStatsTableEntry 32 } allportsStatsOutUcastRate OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Unicast Packets Out rate for port." ::= { allportsStatsTableEntry 33 } allportsStatsInBcastRate OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Broadcasts Packets In rate for port." ::= { allportsStatsTableEntry 34 } allportsStatsOutBcastRate OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Broadcasts Packets Out rate for port." ::= { allportsStatsTableEntry 35 } allportsStatsInMcastRate OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast Packets In rate for port." ::= { allportsStatsTableEntry 36 } allportsStatsOutMcastRate OBJECT-TYPE SYNTAX DisplayString(SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Multicast Packets Out rate for port." ::= { allportsStatsTableEntry 37 } allportsStatsInDiscardsRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Discarded In Packets rate for port." ::= { allportsStatsTableEntry 38 } allportsStatsOutDiscardsRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Discarded Out Packets rate for port." ::= { allportsStatsTableEntry 39 } allportsStatsInErrorsRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Erroneus inbound packets rate for port." ::= { allportsStatsTableEntry 40 } allportsStatsOutErrorsRate OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Not sent packets due to error rate." ::= { allportsStatsTableEntry 41 } clearPortsStats OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(2) results in clearing the statistics for all ports." ::= { portStats 6 } dot1RateStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1RateStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of bridging statistics per second." ::= { portStats 7} dot1RateStatsTableEntry OBJECT-TYPE SYNTAX Dot1RateStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Bridging statistics per second." INDEX { dot1RateStatsIndx } ::= { dot1RateStatsTable 1 } Dot1RateStatsTableEntry ::= SEQUENCE { dot1RateStatsIndx PortNumber, dot1RatePortInFrames Counter32, dot1RatePortOutFrames Counter32, dot1RatePortInDiscards Counter32, dot1RateTpLearnedEntryDiscards Counter32 ,dot1RateStpPortForwardTransitions Counter32 } dot1RateStatsIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port index." ::= { dot1RateStatsTableEntry 1 } dot1RatePortInFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames that have been received per second by this port from its segment." ::= { dot1RateStatsTableEntry 2 } dot1RatePortOutFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames that have been transmitted per second by this port to its segment." ::= { dot1RateStatsTableEntry 3 } dot1RatePortInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of valid frames received which were discarded per second." ::= { dot1RateStatsTableEntry 4 } dot1RateTpLearnedEntryDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number per second of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them." ::= { dot1RateStatsTableEntry 5 } dot1RateStpPortForwardTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this port has transitioned per second from the Learning state to the Forwarding state." ::= { dot1RateStatsTableEntry 8 } dot3RateStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot3RateStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Ethernet statistics per second." ::= { portStats 8} dot3RateStatsTableEntry OBJECT-TYPE SYNTAX Dot3RateStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ethernet statistics per second." INDEX { dot3RateStatsIndx } ::= { dot3RateStatsTable 1 } Dot3RateStatsTableEntry ::= SEQUENCE { dot3RateStatsIndx PortNumber, dot3RateStatsAlignmentErrors Counter32, dot3RateStatsFCSErrors Counter32, dot3RateStatsSingleCollisionFrames Counter32, dot3RateStatsMultipleCollisionFrames Counter32, dot3RateStatsLateCollisions Counter32, dot3RateStatsExcessiveCollisions Counter32, dot3RateStatsInternalMacTransmitErrors Counter32, dot3RateStatsFrameTooLongs Counter32, dot3RateStatsInternalMacReceiveErrors Counter32 } dot3RateStatsIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port index." ::= { dot3RateStatsTableEntry 1 } dot3RateStatsAlignmentErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received per second on a particular interface that are not an integral number of octets in length and do not pass the FCS check." ::= { dot3RateStatsTableEntry 2 } dot3RateStatsFCSErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received per second on a particular interface that are an integral number of octets in length but do not pass the FCS check." ::= { dot3RateStatsTableEntry 3 } dot3RateStatsSingleCollisionFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of successfully transmitted frames per second on a particular interface for which transmission is inhibited by exactly one collision." ::= { dot3RateStatsTableEntry 4 } dot3RateStatsMultipleCollisionFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of successfully transmitted frames per second on a particular interface for which transmission is inhibited by more than one collision." ::= { dot3RateStatsTableEntry 5 } dot3RateStatsLateCollisions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times per second that a collision is detected on a particular interface later than 512 bit-times into the transmission of a packet." ::= { dot3RateStatsTableEntry 8 } dot3RateStatsExcessiveCollisions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count per second of frames for which transmission on a particular interface fails due to excessive collisions." ::= { dot3RateStatsTableEntry 9 } dot3RateStatsInternalMacTransmitErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count per second of frames for which transmission on a particular interface fails due to an internal MAC sublayer transmit error." ::= { dot3RateStatsTableEntry 10 } dot3RateStatsFrameTooLongs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count per second of frames received on a particular interface that exceed the maximum permitted frame size." ::= { dot3RateStatsTableEntry 12 } dot3RateStatsInternalMacReceiveErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count per second of frames for which reception on a particular interface fails due to an internal MAC sublayer receive error." ::= { dot3RateStatsTableEntry 13 } -- NTP Statisitics ntpPrimaryServerReqSent OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of NTP requests sent to Primary NTP Server." ::= { ntpStats 1 } ntpPrimaryServerRespRcvd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of NTP responces received from Primary NTP Server." ::= { ntpStats 2 } ntpPrimaryServerUpdates OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of NTP Updates by Primary NTP Server." ::= { ntpStats 3 } ntpSecondaryServerReqSent OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of NTP requests sent to Secondary NTP Server." ::= { ntpStats 4 } ntpSecondaryServerRespRcvd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of NTP responces received from Secondary NTP Server." ::= { ntpStats 5 } ntpSecondaryServerUpdates OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of NTP Updates by Secondary NTP Server." ::= { ntpStats 6 } ntpLastUpdateServer OBJECT-TYPE SYNTAX INTEGER { none(0), primary(1), secondary(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of ntp server updated last time." ::= { ntpStats 7 } ntpLastUpdateTime OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The last time updated by ntp server." ::= { ntpStats 8 } ntpClearStats OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the stats for ntp." ::= { ntpStats 9 } ntpSystemCurrentTime OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-only STATUS current DESCRIPTION "The current system time." ::= { ntpStats 10 } aclStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AclStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of ACL statistics." ::= { aclStats 1 } aclStatsTableEntry OBJECT-TYPE SYNTAX AclStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics about a particular ACL configuration entry." INDEX { aclStatsIndex } ::= { aclStatsTable 1 } AclStatsTableEntry ::= SEQUENCE { aclStatsIndex Integer32, aclStatsHits Counter32, aclClearStats INTEGER } aclStatsIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The acl index." ::= { aclStatsTableEntry 1 } aclStatsHits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of hits for this ACL entry" ::= { aclStatsTableEntry 2 } aclClearStats OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the stats for the ACL." ::= { aclStatsTableEntry 3 } vmapStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VMAP statistics." ::= { aclStats 2 } vmapStatsTableEntry OBJECT-TYPE SYNTAX VmapStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics about a particular VMAP configuration entry." INDEX { vmapStatsIndex } ::= { vmapStatsTable 1 } VmapStatsTableEntry ::= SEQUENCE { vmapStatsIndex Integer32, vmapStatsHits Counter32, vmapClearStats INTEGER } vmapStatsIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vmap index." ::= { vmapStatsTableEntry 1 } vmapStatsHits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of hits for this VMAP entry" ::= { vmapStatsTableEntry 2 } vmapClearStats OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the stats for the VMAP." ::= { vmapStatsTableEntry 3 } acl6StatsTable OBJECT-TYPE SYNTAX SEQUENCE OF Acl6StatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IPv6 ACL statistics." ::= { aclStats 3 } acl6StatsTableEntry OBJECT-TYPE SYNTAX Acl6StatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics about a particular IPv6 ACL configuration entry." INDEX { aclStatsIndex } ::= { acl6StatsTable 1 } Acl6StatsTableEntry ::= SEQUENCE { acl6StatsIndex Integer32, acl6StatsHits Counter32, acl6ClearStats INTEGER } acl6StatsIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ipv6 acl index." ::= { acl6StatsTableEntry 1 } acl6StatsHits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of hits for this IPv6 ACL entry" ::= { acl6StatsTableEntry 2 } acl6ClearStats OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the stats for the IPv6 ACL." ::= { acl6StatsTableEntry 3 } -- Clear Statistics snmpClearStats OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(2) results in clearing the SNMP statistics." ::= { agClearStats 1 } agDiffState OBJECT-TYPE SYNTAX INTEGER { diff(1), flashdiff(2), idle(3), inprogress(4), complete(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "When this object is read the current state is returned. idle(3) indicates that there is no diff in progess. complete(5) indicates that the last diff operation is completed. Setting the value to diff(1), will start a new diff operation Diff compares the new configuration with the current configuration and shows the pending configuration changes. Setting the value to flashdiff(1), will start a new diff operation. flashdiff compares new configuration with the flash configuration. To read the configuration changes use the agDiffTable once the state of this variable returns complete. Once the agDiffTable is read the state should be set back to 'idle' which frees the diff buffer and others can issue a diff command via SNMP." ::= { agDiff 2 } agDiffTableSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of strings in the diff table." ::= { agDiff 3 } agDiffTable OBJECT-TYPE SYNTAX SEQUENCE OF AgDiffTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of diff strings." ::= { agDiff 4 } agDiffTableEntry OBJECT-TYPE SYNTAX AgDiffTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the diff table." INDEX { agDiffIndex } ::= { agDiffTable 1 } AgDiffTableEntry ::= SEQUENCE { agDiffIndex Integer32, agDiffString OCTET STRING } agDiffIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The table index." ::= { agDiffTableEntry 1 } agDiffString OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "A string in the diff table." ::= { agDiffTableEntry 2 } -- Config Dump agCfgDumpState OBJECT-TYPE SYNTAX INTEGER { dump(1), idle(2), inprogress(3), complete(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "When this object is read the current state is returned. idle(2) indicates that there is no dump in progess. complete(4) indicates that the last dump operation is completed. Setting the value to dump(1), will start a new dump operation Dump will show the current configuration. To read the configuration dump use the agCfgDumpTable once the state of this variable returns complete. Once the agCfgDumpTable is read the state should be set back to 'idle' which frees the dump buffer and others can issue a dump command via SNMP." ::= { agCfgDump 2 } agCfgDumpTableSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of strings in the dump table." ::= { agCfgDump 3 } agCfgDumpTable OBJECT-TYPE SYNTAX SEQUENCE OF AgCfgDumpTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of dump strings." ::= { agCfgDump 4 } agCfgDumpTableEntry OBJECT-TYPE SYNTAX AgCfgDumpTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the dump table." INDEX { agCfgDumpIndex } ::= { agCfgDumpTable 1 } AgCfgDumpTableEntry ::= SEQUENCE { agCfgDumpIndex Integer32, agCfgDumpString OCTET STRING } agCfgDumpIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The table index." ::= { agCfgDumpTableEntry 1 } agCfgDumpString OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "A string in the dump table." ::= { agCfgDumpTableEntry 2 } -- Memory Statisitics Group totalMemoryStats OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total memory in bytes." ::= { memoryStats 1} memoryFreeStats OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The free memory in bytes." ::= { memoryStats 2} memorySharedStats OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The shared memory in bytes." ::= { memoryStats 3} memoryBufferStats OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The buffer memory in bytes." ::= { memoryStats 4} swapTotalStats OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total swap memory in bytes." ::= { memoryStats 5} swapFreeStats OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The free swap memory in bytes." ::= { memoryStats 6} highTotalStats OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total high memory in bytes." ::= { memoryStats 7} highFreeStats OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The free high memory in bytes." ::= { memoryStats 8} -- GeaPort Information geaportInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF GeaportInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of gea port mapping." ::= { geaportInfo 1 } geaportInfoTableEntry OBJECT-TYPE SYNTAX GeaportInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the geaport table mapping." INDEX { geaportInfoLogicalIndex } ::= { geaportInfoTable 1 } GeaportInfoTableEntry ::= SEQUENCE { geaportInfoLogicalIndex PortNumber, geaportInfoAlias DisplayString, geaportInfoPort INTEGER, geaportInfoUnit INTEGER } geaportInfoLogicalIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The logical port index." ::= { geaportInfoTableEntry 1 } geaportInfoAlias OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The GEA Port Alias." ::= { geaportInfoTableEntry 2 } geaportInfoPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The GEA Port (0-based)." ::= { geaportInfoTableEntry 3 } geaportInfoUnit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The GEA Unit." ::= { geaportInfoTableEntry 4 } -- SFP Information sfpInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF SfpInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of external port SFP information." ::= { sfpInfo 1 } sfpInfoTableEntry OBJECT-TYPE SYNTAX SfpInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the external port SFP information table." INDEX { sfpInfoIndx } ::= { sfpInfoTable 1 } SfpInfoTableEntry ::= SEQUENCE { sfpInfoIndx PortNumber, sfpInfoPort DisplayString, sfpInfoDevice DisplayString, sfpInfoTXEnable INTEGER, sfpInfoRXSignal INTEGER, sfpInfoTXFault INTEGER, sfpInfoApproved INTEGER, sfpInfoVendor DisplayString, sfpInfoSerial DisplayString , sfpInfoPartNumber DisplayString, sfpInfoRevision DisplayString, sfpInfoVoltage DisplayString, sfpInfoTemperature DisplayString, sfpInfoWaveLength DisplayString } sfpInfoIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The external port SFX index." ::= { sfpInfoTableEntry 1 } sfpInfoPort OBJECT-TYPE SYNTAX DisplayString (SIZE(0..6)) MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP alias." ::= { sfpInfoTableEntry 2 } sfpInfoDevice OBJECT-TYPE SYNTAX DisplayString (SIZE(0..6)) MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP Device." ::= { sfpInfoTableEntry 3 } sfpInfoTXEnable OBJECT-TYPE SYNTAX INTEGER { notInstalled (1), enabled (2), disabled (3) , notAvailable (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP TX-Enable." ::= { sfpInfoTableEntry 4 } sfpInfoRXSignal OBJECT-TYPE SYNTAX INTEGER { notInstalled (1), down (2), link (3), notAvailable (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP RX-Signal." ::= { sfpInfoTableEntry 5 } sfpInfoTXFault OBJECT-TYPE SYNTAX INTEGER { notInstalled (1), fault (2), none (3), notAvailable (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP TX-Fault." ::= { sfpInfoTableEntry 6 } sfpInfoApproved OBJECT-TYPE SYNTAX INTEGER { notInstalled (1), notApproved (2), sfpApproved (3) ,sfpAccepted (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP Approval." ::= { sfpInfoTableEntry 7 } sfpInfoVendor OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP device vendor." ::= { sfpInfoTableEntry 8 } sfpInfoSerial OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP device serial." ::= { sfpInfoTableEntry 9 } sfpInfoPartNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP device part number." ::= { sfpInfoTableEntry 10 } sfpInfoRevision OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP device revision." ::= { sfpInfoTableEntry 11 } sfpInfoVoltage OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP device voltage." ::= { sfpInfoTableEntry 12 } sfpInfoTemperature OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP device temperature." ::= { sfpInfoTableEntry 13 } sfpInfoWaveLength OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "External Port SFP/XFP device laser wave length." ::= { sfpInfoTableEntry 14 } accessInfoClearAllUserFailAttempts OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action Object. When set to clear(2),clears all the unsuccessful attempts of users. Otherwise nothing is done. ok(1) is returned always when read." ::= { accessInfo 1 } accessInfoClearAllUserLocks OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action Object. When set to clear(2), Unlock all locked users. Otherwise nothing is done. ok(1) is returned always when read." ::= { accessInfo 2 } accessUserInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF AccessUserInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of user information." ::= { accessInfo 3 } accessUserInfoTableEntry OBJECT-TYPE SYNTAX AccessUserInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the user information table." INDEX { accessUserInfoIndex} ::= { accessUserInfoTable 1 } AccessUserInfoTableEntry ::= SEQUENCE { accessUserInfoIndex Integer32, accessUserInfoLockState INTEGER, accessUserInfoClearFailAttempts INTEGER, accessUserInfoClearLock INTEGER } accessUserInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The table index. The index value corresponds to the same value of agAccessUserCurCfgUId for the user." ::= { accessUserInfoTableEntry 1 } accessUserInfoLockState OBJECT-TYPE SYNTAX INTEGER { unlocked(1), locked(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Lock State of a specific user, unlocked(1) or locked(2). When the state is locked the user is not allowed to login until the account is unlocked by the administrator." ::= { accessUserInfoTableEntry 2 } accessUserInfoClearFailAttempts OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action Object. When set to clear(2), clears the unsuccessful attempts of a particular user. Otherwise nothing is done. ok(1) is returned always when read." ::= { accessUserInfoTableEntry 3 } accessUserInfoClearLock OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action Object. When set to clear(2), unlock a particular user. Otherwise nothing is done. ok(1) is returned always when read." ::= { accessUserInfoTableEntry 4 } -- endif /* defined(WEB_UI) */ -- ---------------------------------------------------------------------------- -- } INSERT: agent -- ---------------------------------------------------------------------------- layer2 OBJECT IDENTIFIER ::= { g8052-mgmt 2 } -- ---------------------------------------------------------------------------- -- { INSERT: layer2 -- ---------------------------------------------------------------------------- layer2Configs OBJECT IDENTIFIER ::= { layer2 1 } layer2Stats OBJECT IDENTIFIER ::= { layer2 2 } layer2Info OBJECT IDENTIFIER ::= { layer2 3 } layer2Oper OBJECT IDENTIFIER ::= { layer2 4 } vlan OBJECT IDENTIFIER ::= { layer2Configs 1 } trunkgroup OBJECT IDENTIFIER ::= { layer2Configs 2 } stgCfg OBJECT IDENTIFIER ::= { layer2Configs 3 } mirroring OBJECT IDENTIFIER ::= { layer2Configs 4 } lacp OBJECT IDENTIFIER ::= { layer2Configs 5 } thash OBJECT IDENTIFIER ::= { layer2Configs 6 } mstCfg OBJECT IDENTIFIER ::= { layer2Configs 7 } l2GeneralCfg OBJECT IDENTIFIER ::= { layer2Configs 8 } failoverCfg OBJECT IDENTIFIER ::= { layer2Configs 10 } -- ---------------------------------------------------------------------------- -- { INSERT: failoverCfg -- ---------------------------------------------------------------------------- -- ---------------------------------------------------------------------------- -- { GLOBAL TEAMING CONFIG -- ---------------------------------------------------------------------------- failoverCurCfgOnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Failover ON/OFF setting." ::= { failoverCfg 1 } failoverNewCfgOnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Failover ON/OFF settings." ::= { failoverCfg 2 } failoverMaxTriggerEntries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in the Failover Trigger Table." ::= { failoverCfg 5 } -- } GLOBAL TEAMING CONFIG -- ---------------------------------------------------------------------------- -- { CUR TEAMING FOP CONFIG -- ---------------------------------------------------------------------------- failoverCurCfgTriggerTable OBJECT-TYPE SYNTAX SEQUENCE OF FailoverCurCfgTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Failover Trigger Table." ::= { failoverCfg 6 } failoverCurCfgTriggerTableEntry OBJECT-TYPE SYNTAX FailoverCurCfgTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Failover Trigger Table." INDEX { failoverCurCfgTriggerId } ::= { failoverCurCfgTriggerTable 1 } FailoverCurCfgTriggerTableEntry ::= SEQUENCE { failoverCurCfgTriggerId Integer32, failoverCurCfgTriggerLimit INTEGER, failoverCurCfgTriggerMmonPort OCTET STRING, failoverCurCfgTriggerMmonTrunk OCTET STRING, failoverCurCfgTriggerMmonKey DisplayString, failoverCurCfgTriggerMconPort OCTET STRING, failoverCurCfgTriggerMconTrunk OCTET STRING, failoverCurCfgTriggerMconKey DisplayString, failoverCurCfgTriggerState INTEGER } failoverCurCfgTriggerId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Trigger identifier." ::= { failoverCurCfgTriggerTableEntry 1 } failoverCurCfgTriggerState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable Trigger state" ::= { failoverCurCfgTriggerTableEntry 2 } failoverCurCfgTriggerLimit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Limit # of operational links" ::= { failoverCurCfgTriggerTableEntry 3 } failoverCurCfgTriggerMmonPort OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Manual Monitor port list. The ports are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the Manual Monitor 0 - The represented port does not belong to the Manual Monitor" ::= { failoverCurCfgTriggerTableEntry 6 } failoverCurCfgTriggerMmonTrunk OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Manual Monitor trunk list. The trunks are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk 8 || || || ||___ trunk 7 || |____ trunk 6 || . . . ||_________ trunk 1 |__________ reserved where x : 1 - The represented trunk belongs to the Manual Monitor 0 - The represented trunk does not belong to the Manual Monitor" ::= { failoverCurCfgTriggerTableEntry 7 } failoverCurCfgTriggerMmonKey OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The LACP admin key. This is an array of 16-bit read-only values." ::= { failoverCurCfgTriggerTableEntry 8 } failoverCurCfgTriggerMconPort OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Manual Control port list. The ports are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the Manual Control 0 - The represented port does not belong to the Manual Control" ::= { failoverCurCfgTriggerTableEntry 9 } failoverCurCfgTriggerMconTrunk OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Manual Control trunk list. The trunks are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk 8 || || || ||___ trunk 7 || |____ trunk 6 || . . . ||_________ trunk 1 |__________ reserved where x : 1 - The represented trunk belongs to the Manual Control 0 - The represented trunk does not belong to the Manual Control" ::= { failoverCurCfgTriggerTableEntry 11 } failoverCurCfgTriggerMconKey OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The LACP admin key. This is an array of 16-bit read-only values." ::= { failoverCurCfgTriggerTableEntry 12 } -- } CUR TEAMING FOP CONFIG -- ---------------------------------------------------------------------------- -- { NEW TEAMING FOP CONFIG -- ---------------------------------------------------------------------------- failoverNewCfgTriggerTable OBJECT-TYPE SYNTAX SEQUENCE OF FailoverNewCfgTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Failover Trigger Table." ::= { failoverCfg 7 } failoverNewCfgTriggerTableEntry OBJECT-TYPE SYNTAX FailoverNewCfgTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Failover Trigger Table." INDEX { failoverNewCfgTriggerId } ::= { failoverNewCfgTriggerTable 1 } FailoverNewCfgTriggerTableEntry ::= SEQUENCE { failoverNewCfgTriggerId Integer32, failoverNewCfgTriggerLimit INTEGER, failoverNewCfgTriggerMmonPort OCTET STRING, failoverNewCfgTriggerMmonPortAdd PortNumber, failoverNewCfgTriggerMmonPortRem PortNumber, failoverNewCfgTriggerMmonTrunk OCTET STRING, failoverNewCfgTriggerMmonTrunkAdd INTEGER, failoverNewCfgTriggerMmonTrunkRem INTEGER, failoverNewCfgTriggerMmonKey DisplayString, failoverNewCfgTriggerMmonKeyAdd INTEGER, failoverNewCfgTriggerMmonKeyRem INTEGER, failoverNewCfgTriggerMconPort OCTET STRING, failoverNewCfgTriggerMconPortAdd PortNumber, failoverNewCfgTriggerMconPortRem PortNumber, failoverNewCfgTriggerMconTrunk OCTET STRING, failoverNewCfgTriggerMconTrunkAdd INTEGER, failoverNewCfgTriggerMconTrunkRem INTEGER, failoverNewCfgTriggerMconKey DisplayString, failoverNewCfgTriggerMconKeyAdd INTEGER, failoverNewCfgTriggerMconKeyRem INTEGER, failoverNewCfgTriggerState INTEGER, failoverNewCfgTriggerDelete INTEGER } failoverNewCfgTriggerId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Trigger identifier." ::= { failoverNewCfgTriggerTableEntry 1 } failoverNewCfgTriggerState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable Trigger state" ::= { failoverNewCfgTriggerTableEntry 2 } failoverNewCfgTriggerLimit OBJECT-TYPE SYNTAX INTEGER (0..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "Limit # of operational links" ::= { failoverNewCfgTriggerTableEntry 3 } failoverNewCfgTriggerMmonPort OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Manual Monitor port list. The ports are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the Manual Monitor 0 - The represented port does not belong to the Manual Monitor" ::= { failoverNewCfgTriggerTableEntry 10 } failoverNewCfgTriggerMmonPortAdd OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "Add port to Manual Monitor. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 11 } failoverNewCfgTriggerMmonPortRem OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "Remove port from Manual Monitor. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 12 } failoverNewCfgTriggerMmonTrunk OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Manual Monitor trunk list. The trunks are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk 8 || || || ||___ trunk 7 || |____ trunk 6 || . . . ||_________ trunk 1 |__________ reserved where x : 1 - The represented trunk belongs to the Manual Monitor 0 - The represented trunk does not belong to the Manual Monitor" ::= { failoverNewCfgTriggerTableEntry 13 } failoverNewCfgTriggerMmonTrunkAdd OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "Add trunk to Manual Monitor. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 14 } failoverNewCfgTriggerMmonTrunkRem OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "Remove trunk from Manual Monitor. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 15 } failoverNewCfgTriggerMmonKey OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The LACP admin key. This is an array of 16-bit read-only values." ::= { failoverNewCfgTriggerTableEntry 16 } failoverNewCfgTriggerMmonKeyAdd OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Add LACP admin key to Manual Monitor. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 17 } failoverNewCfgTriggerMmonKeyRem OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Remove LACP admin key from Manual Monitor. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 18 } failoverNewCfgTriggerMconPort OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Manual Control port list. The ports are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the Manual Control 0 - The represented port does not belong to the Manual Control" ::= { failoverNewCfgTriggerTableEntry 19 } failoverNewCfgTriggerMconPortAdd OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "Add port to Manual Control. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 20 } failoverNewCfgTriggerMconPortRem OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "Remove port from Manual Control. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 21 } failoverNewCfgTriggerMconTrunk OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Manual Control trunk list. The trunks are presented in bitmap format: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk 8 || || || ||___ trunk 7 || |____ trunk 6 || . . . ||_________ trunk 1 |__________ reserved where x : 1 - The represented trunk belongs to the Manual Control 0 - The represented trunk does not belong to the Manual Control" ::= { failoverNewCfgTriggerTableEntry 25 } failoverNewCfgTriggerMconTrunkAdd OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "Add trunk to Manual Control. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 26 } failoverNewCfgTriggerMconTrunkRem OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "Remove trunk from Manual Control. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 27 } failoverNewCfgTriggerMconKey OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The LACP admin key. This is an array of 16-bit read-only values." ::= { failoverNewCfgTriggerTableEntry 28 } failoverNewCfgTriggerMconKeyAdd OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Add LACP admin key to Manual Control. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 29 } failoverNewCfgTriggerMconKeyRem OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Remove LACP admin key from Manual Control. When read, 0 is returned." ::= { failoverNewCfgTriggerTableEntry 30 } failoverNewCfgTriggerDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Setting the value to delete(2) will delete the entire row. When read, other(1) is returned." ::= { failoverNewCfgTriggerTableEntry 31 } -- } NEW TEAMING FOP CONFIG -- ---------------------------------------------------------------------------- -- } INSERT: failoverCfg -- ---------------------------------------------------------------------------- dot1x OBJECT IDENTIFIER ::= { layer2Configs 12 } fdb OBJECT IDENTIFIER ::= { layer2Configs 13 } hotlinksCfg OBJECT IDENTIFIER ::= { layer2Configs 14 } -- ---------------------------------------------------------------------------- -- { INSERT: hotlinksCfg -- ---------------------------------------------------------------------------- -- ---------------------------------------------------------------------------- -- { GLOBAL HOTLINKS CONFIG -- ---------------------------------------------------------------------------- hotlinksCurCfgOnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Hot Links ON/OFF setting." ::= { hotlinksCfg 1 } hotlinksNewCfgOnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Hot Links ON/OFF settings." ::= { hotlinksCfg 2 } hotlinksCurCfgFdbUpdateState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Hot Links FDB Update setting." ::= { hotlinksCfg 3 } hotlinksNewCfgFdbUpdateState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable Hot Links FDB Update setting." ::= { hotlinksCfg 4 } hotlinksMaxTriggerEntries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in the Hot Links Trigger Table." ::= { hotlinksCfg 5 } -- } GLOBAL HOTLINKS CONFIG -- ---------------------------------------------------------------------------- -- { CUR HOTLINKS FOP CONFIG -- ---------------------------------------------------------------------------- hotlinksCurCfgTriggerTable OBJECT-TYPE SYNTAX SEQUENCE OF HotlinksCurCfgTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Hot Links Trigger Table." ::= { hotlinksCfg 6 } hotlinksCurCfgTriggerTableEntry OBJECT-TYPE SYNTAX HotlinksCurCfgTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Hot Links Trigger Table." INDEX { hotlinksCurCfgTriggerId } ::= { hotlinksCurCfgTriggerTable 1 } HotlinksCurCfgTriggerTableEntry ::= SEQUENCE { hotlinksCurCfgTriggerId Integer32, hotlinksCurCfgTriggerName DisplayString, hotlinksCurCfgTriggerState INTEGER, hotlinksCurCfgTriggerPreemptState INTEGER, hotlinksCurCfgTriggerFdelay Integer32, hotlinksCurCfgTriggerMasterPort Integer32, hotlinksCurCfgTriggerMasterTrunk Integer32, hotlinksCurCfgTriggerBackupPort Integer32, hotlinksCurCfgTriggerBackupTrunk Integer32, hotlinksCurCfgTriggerDelete INTEGER , hotlinksCurCfgTriggerMasterAdminkey Integer32 , hotlinksCurCfgTriggerBackupAdminkey Integer32 } hotlinksCurCfgTriggerId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Trigger identifier." ::= { hotlinksCurCfgTriggerTableEntry 1 } hotlinksCurCfgTriggerName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A textual string containing the trigger name." ::= { hotlinksCurCfgTriggerTableEntry 2 } hotlinksCurCfgTriggerState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Trigger state." ::= { hotlinksCurCfgTriggerTableEntry 3 } hotlinksCurCfgTriggerPreemptState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Preemption state." ::= { hotlinksCurCfgTriggerTableEntry 4 } hotlinksCurCfgTriggerFdelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Forward Delay setting (in secs)." ::= { hotlinksCurCfgTriggerTableEntry 5 } hotlinksCurCfgTriggerMasterPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The master interface port number." ::= { hotlinksCurCfgTriggerTableEntry 6 } hotlinksCurCfgTriggerMasterTrunk OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The master interface trunk number." ::= { hotlinksCurCfgTriggerTableEntry 7 } hotlinksCurCfgTriggerBackupPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The backup interface port number." ::= { hotlinksCurCfgTriggerTableEntry 8 } hotlinksCurCfgTriggerBackupTrunk OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The backup interface trunk number." ::= { hotlinksCurCfgTriggerTableEntry 9 } hotlinksCurCfgTriggerDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Delete a Hot Links trigger configuration." ::= { hotlinksCurCfgTriggerTableEntry 10 } hotlinksCurCfgTriggerMasterAdminkey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The master interface admin key number." ::= { hotlinksCurCfgTriggerTableEntry 11 } hotlinksCurCfgTriggerBackupAdminkey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The backup interface admin key number." ::= { hotlinksCurCfgTriggerTableEntry 12 } -- } CUR HOTLINKS FOP CONFIG -- ---------------------------------------------------------------------------- -- { NEW HOTLINKS FOP CONFIG -- ---------------------------------------------------------------------------- hotlinksNewCfgTriggerTable OBJECT-TYPE SYNTAX SEQUENCE OF HotlinksNewCfgTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Hot Links Trigger Table." ::= { hotlinksCfg 7 } hotlinksNewCfgTriggerTableEntry OBJECT-TYPE SYNTAX HotlinksNewCfgTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Hot Links Trigger Table." INDEX { hotlinksNewCfgTriggerId } ::= { hotlinksNewCfgTriggerTable 1 } HotlinksNewCfgTriggerTableEntry ::= SEQUENCE { hotlinksNewCfgTriggerId Integer32, hotlinksNewCfgTriggerName DisplayString, hotlinksNewCfgTriggerState INTEGER, hotlinksNewCfgTriggerPreemptState INTEGER, hotlinksNewCfgTriggerFdelay Integer32, hotlinksNewCfgTriggerMasterPort Integer32, hotlinksNewCfgTriggerMasterTrunk Integer32, hotlinksNewCfgTriggerBackupPort Integer32, hotlinksNewCfgTriggerBackupTrunk Integer32, hotlinksNewCfgTriggerDelete INTEGER , hotlinksNewCfgTriggerMasterAdminkey Integer32 , hotlinksNewCfgTriggerBackupAdminkey Integer32 } hotlinksNewCfgTriggerId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Trigger identifier." ::= { hotlinksNewCfgTriggerTableEntry 1 } hotlinksNewCfgTriggerName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..33)) MAX-ACCESS read-write STATUS current DESCRIPTION "A textual string containing the trigger name." ::= { hotlinksNewCfgTriggerTableEntry 2 } hotlinksNewCfgTriggerState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable Trigger state." ::= { hotlinksNewCfgTriggerTableEntry 3 } hotlinksNewCfgTriggerPreemptState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable Preemption state." ::= { hotlinksNewCfgTriggerTableEntry 4 } hotlinksNewCfgTriggerFdelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Forward Delay setting (in secs)." ::= { hotlinksNewCfgTriggerTableEntry 5 } hotlinksNewCfgTriggerMasterPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The master interface port number." ::= { hotlinksNewCfgTriggerTableEntry 6 } hotlinksNewCfgTriggerMasterTrunk OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The master interface trunk number." ::= { hotlinksNewCfgTriggerTableEntry 7 } hotlinksNewCfgTriggerBackupPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The backup interface port number." ::= { hotlinksNewCfgTriggerTableEntry 8 } hotlinksNewCfgTriggerBackupTrunk OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The backup interface trunk number." ::= { hotlinksNewCfgTriggerTableEntry 9 } hotlinksNewCfgTriggerDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete a Hot Links trigger configuration." ::= { hotlinksNewCfgTriggerTableEntry 10 } hotlinksNewCfgTriggerMasterAdminkey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The master interface admin key number." ::= { hotlinksNewCfgTriggerTableEntry 11 } hotlinksNewCfgTriggerBackupAdminkey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The backup interface admin key number." ::= { hotlinksNewCfgTriggerTableEntry 12 } -- } NEW HOTLINKS FOP CONFIG -- ---------------------------------------------------------------------------- -- { BPDU FLOOD CONFIG -- ---------------------------------------------------------------------------- hotlinksCurCfgBpduState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Hot Links BPDU flood setting." ::= { hotlinksCfg 8 } hotlinksNewCfgBpduState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable Hot Links BPDU flood setting." ::= { hotlinksCfg 9 } -- } BPDU FLOOD CONFIG -- ---------------------------------------------------------------------------- -- { FDB UPDATE RATE CONFIG -- ---------------------------------------------------------------------------- hotlinksCurCfgFdbUpdateRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Hot Links FDB update rate (packets per second)." ::= { hotlinksCfg 10 } hotlinksNewCfgFdbUpdateRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Hot Links FDB update rate (packets per second)." ::= { hotlinksCfg 11 } -- } FDB UPDATE RATE CONFIG -- ---------------------------------------------------------------------------- -- } INSERT: hotlinksCfg -- ---------------------------------------------------------------------------- lldpCfg OBJECT IDENTIFIER ::= { layer2Configs 15 } vlagCfg OBJECT IDENTIFIER ::= { layer2Configs 18 } vlagIslCfg OBJECT IDENTIFIER ::= { vlagCfg 1 } ecpCfg OBJECT IDENTIFIER ::= { layer2Configs 19 } thashL2 OBJECT IDENTIFIER ::= { thash 1 } mirrPortMirr OBJECT IDENTIFIER ::= { mirroring 1 } mstGeneralCfg OBJECT IDENTIFIER ::= { mstCfg 1 } mstCistCfg OBJECT IDENTIFIER ::= { mstCfg 2 } dot1xCurCfgGlobalTable OBJECT IDENTIFIER ::= { dot1x 5 } dot1xCurCfgGuestVlan OBJECT IDENTIFIER ::= { dot1xCurCfgGlobalTable 1 } dot1xNewCfgGlobalTable OBJECT IDENTIFIER ::= { dot1x 6 } fdbGeneralCfg OBJECT IDENTIFIER ::= { fdb 1 } -- FDB fdbCurCfgAgingTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Fdb current aging time" ::= { fdbGeneralCfg 1 } fdbNewCfgAgingTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Fdb new aging time." ::= { fdbGeneralCfg 2 } dot1xNewCfgGuestVlan OBJECT IDENTIFIER ::= { dot1xNewCfgGlobalTable 1 } fdbStats OBJECT IDENTIFIER ::= { layer2Stats 1 } stpStats OBJECT IDENTIFIER ::= { layer2Stats 2 } lacpStats OBJECT IDENTIFIER ::= { layer2Stats 4 } hotlinksStats OBJECT IDENTIFIER ::= { layer2Stats 6 } -- ---------------------------------------------------------------------------- -- { INSERT: hotlinksStats -- ---------------------------------------------------------------------------- hotlinksStatsTriggerTable OBJECT-TYPE SYNTAX SEQUENCE OF HotlinksStatsTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Hot Links Trigger Table Stats." ::= { hotlinksStats 1 } hotlinksStatsTriggerTableEntry OBJECT-TYPE SYNTAX HotlinksStatsTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Hot Links Trigger Table Stats." INDEX { hotlinksStatsTriggerId } ::= { hotlinksStatsTriggerTable 1 } HotlinksStatsTriggerTableEntry ::= SEQUENCE { hotlinksStatsTriggerId Integer32, hotlinksStatsTriggerName DisplayString, hotlinksStatsTriggerMasterActive Integer32, hotlinksStatsTriggerBackupActive Integer32, hotlinksStatsTriggerFdbUpdate Integer32, hotlinksStatsTriggerFdbFailed Integer32 } hotlinksStatsTriggerId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Trigger identifier." ::= { hotlinksStatsTriggerTableEntry 1 } hotlinksStatsTriggerName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A textual string containing the trigger name." ::= { hotlinksStatsTriggerTableEntry 2 } hotlinksStatsTriggerMasterActive OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the master interface was set to active." ::= { hotlinksStatsTriggerTableEntry 3 } hotlinksStatsTriggerBackupActive OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times the backup interface was set to active." ::= { hotlinksStatsTriggerTableEntry 4 } hotlinksStatsTriggerFdbUpdate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times an FDB update was performed." ::= { hotlinksStatsTriggerTableEntry 5 } hotlinksStatsTriggerFdbFailed OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times an FDB update failed." ::= { hotlinksStatsTriggerTableEntry 6 } -- ---------------------------------------------------------------------------- -- } INSERT: hotlinksStats -- ---------------------------------------------------------------------------- lldpStats OBJECT IDENTIFIER ::= { layer2Stats 7 } oamStats OBJECT IDENTIFIER ::= { layer2Stats 8 } vlagStats OBJECT IDENTIFIER ::= { layer2Stats 11 } vlagStatsSystem OBJECT IDENTIFIER ::= { vlagStats 1 } vlagStatsIsl OBJECT IDENTIFIER ::= { vlagStats 2 } vlagStatsHealth OBJECT IDENTIFIER ::= { vlagStats 3 } vlagStatsLacp OBJECT IDENTIFIER ::= { vlagStats 4 } vlagStatsPdu OBJECT IDENTIFIER ::= { vlagStats 5 } vlagStatsIgmp OBJECT IDENTIFIER ::= { vlagStats 6 } fdbInfo OBJECT IDENTIFIER ::= { layer2Info 1 } stpInfo OBJECT IDENTIFIER ::= { layer2Info 2 } lacpInfo OBJECT IDENTIFIER ::= { layer2Info 3 } cistInfo OBJECT IDENTIFIER ::= { layer2Info 4 } genInfo OBJECT IDENTIFIER ::= { layer2Info 7 } vlanInfo OBJECT IDENTIFIER ::= { layer2Info 5 } dot1xInfo OBJECT IDENTIFIER ::= { layer2Info 6 } trunkGroupInfo OBJECT IDENTIFIER ::= { layer2Info 9 } hotlinksInfo OBJECT IDENTIFIER ::= { layer2Info 10 } -- ---------------------------------------------------------------------------- -- { INSERT: hotlinksInfo -- ---------------------------------------------------------------------------- hotlinksInfoOnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Hot Links ON/OFF setting info." ::= { hotlinksInfo 1 } hotlinksInfoFdbUpdateState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Hot Links FDB Update setting info." ::= { hotlinksInfo 2 } hotlinksInfoTriggerTable OBJECT-TYPE SYNTAX SEQUENCE OF HotlinksInfoTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Hot Links Trigger Table Info." ::= { hotlinksInfo 3 } hotlinksInfoBpduState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Hot Links BPDU flood setting info." ::= { hotlinksInfo 4 } hotlinksInfoFdbUpdateRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Hot Links FDB update rate (packets per second)." ::= { hotlinksInfo 5 } hotlinksInfoTriggerTableEntry OBJECT-TYPE SYNTAX HotlinksInfoTriggerTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Hot Links Trigger Table Info." INDEX { hotlinksInfoTriggerId } ::= { hotlinksInfoTriggerTable 1 } HotlinksInfoTriggerTableEntry ::= SEQUENCE { hotlinksInfoTriggerId Integer32, hotlinksInfoTriggerName DisplayString, hotlinksInfoTriggerState INTEGER, hotlinksInfoTriggerPreemptState INTEGER, hotlinksInfoTriggerFdelay Integer32, hotlinksInfoTriggerActive DisplayString } hotlinksInfoTriggerId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Trigger identifier." ::= { hotlinksInfoTriggerTableEntry 1 } hotlinksInfoTriggerName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A textual string containing the trigger name." ::= { hotlinksInfoTriggerTableEntry 2 } hotlinksInfoTriggerState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Trigger state info." ::= { hotlinksInfoTriggerTableEntry 3 } hotlinksInfoTriggerPreemptState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Preemption state info." ::= { hotlinksInfoTriggerTableEntry 4 } hotlinksInfoTriggerFdelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Forward Delay setting info (in secs)." ::= { hotlinksInfoTriggerTableEntry 5 } hotlinksInfoTriggerActive OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A textual string containing the active interface info." ::= { hotlinksInfoTriggerTableEntry 6 } -- ---------------------------------------------------------------------------- -- } INSERT: hotlinksInfo -- ---------------------------------------------------------------------------- lldpInfo OBJECT IDENTIFIER ::= { layer2Info 11 } cistGeneralInfo OBJECT IDENTIFIER ::= { cistInfo 1 } dot1xSystemInfo OBJECT IDENTIFIER ::= { dot1xInfo 2 } oamInfo OBJECT IDENTIFIER ::= { layer2Info 12 } udldInfo OBJECT IDENTIFIER ::= { layer2Info 13 } failoverInfo OBJECT IDENTIFIER ::= { layer2Info 14 } -- ---------------------------------------------------------------------------- -- { INSERT: failoverInfo -- ---------------------------------------------------------------------------- failoverInfoState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current state of failover" ::= { failoverInfo 1 } failoverInfoTriggerTable OBJECT-TYPE SYNTAX SEQUENCE OF FailoverInfoTriggerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table holds the information for individual triggers" ::= { failoverInfo 3 } failoverInfoTriggerEntry OBJECT-TYPE SYNTAX FailoverInfoTriggerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the failover trigger table." INDEX { failoverInfoTriggerId } ::= { failoverInfoTriggerTable 1 } FailoverInfoTriggerEntry ::= SEQUENCE { failoverInfoTriggerId Integer32, failoverInfoTriggerState INTEGER, failoverInfoTriggerLimit INTEGER, failoverInfoTriggerMonitorState INTEGER, failoverInfoTriggerMonitorPorts OCTET STRING, failoverInfoTriggerControlState INTEGER, failoverInfoTriggerControlPorts OCTET STRING, failoverInfoTriggerControlPorts OCTET STRING } failoverInfoTriggerId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The trigger identifier." ::= { failoverInfoTriggerEntry 1 } failoverInfoTriggerState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The trigger state." ::= { failoverInfoTriggerEntry 2 } failoverInfoTriggerLimit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Limit number of operational links" ::= { failoverInfoTriggerEntry 3 } failoverInfoTriggerMonitorState OBJECT-TYPE SYNTAX INTEGER{ up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The runtime monitor state" ::= { failoverInfoTriggerEntry 4 } failoverInfoTriggerMonitorPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The list of ports that are monitored. The ports are represented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to Monitor list 0 - The represented port does not belong to Monitor list" ::= { failoverInfoTriggerEntry 5 } failoverInfoTriggerControlState OBJECT-TYPE SYNTAX INTEGER{ auto-controlled(1), auto-disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The runtime control state" ::= { failoverInfoTriggerEntry 6 } failoverInfoTriggerControlPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The list of ports that are controlled. The ports are represented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to Control list 0 - The represented port does not belong to Control list" ::= { failoverInfoTriggerEntry 7 } failoverInfoMonPortStateTable OBJECT-TYPE SYNTAX SEQUENCE OF FailoverInfoTriggerMonPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table holds the information for individual triggers" ::= { failoverInfo 4 } failoverInfoTriggerMonPortEntry OBJECT-TYPE SYNTAX FailoverInfoTriggerMonPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the failover trigger table." INDEX { failoverInfoTriggerMonId, failoverInfoTriggerMonPortId } ::= { failoverInfoMonPortStateTable 1 } FailoverInfoTriggerMonPortEntry ::= SEQUENCE { failoverInfoTriggerMonId Integer32, failoverInfoTriggerMonPortId PortNumber, failoverInfoTriggerMonPortStatus INTEGER } failoverInfoTriggerMonId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The trigger identifier." ::= { failoverInfoTriggerMonPortEntry 1 } failoverInfoTriggerMonPortId OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The Port identifier." ::= { failoverInfoTriggerMonPortEntry 2 } failoverInfoTriggerMonPortStatus OBJECT-TYPE SYNTAX INTEGER{ failed(0), operational(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Status." ::= { failoverInfoTriggerMonPortEntry 3 } failoverInfoCtlPortStateTable OBJECT-TYPE SYNTAX SEQUENCE OF FailoverInfoTriggerCtlPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table holds the information for individual triggers" ::= { failoverInfo 5 } failoverInfoTriggerCtlPortEntry OBJECT-TYPE SYNTAX FailoverInfoTriggerCtlPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the failover trigger table." INDEX { failoverInfoTriggerCtlId, failoverInfoTriggerCtlPortId } ::= { failoverInfoCtlPortStateTable 1 } FailoverInfoTriggerCtlPortEntry ::= SEQUENCE { failoverInfoTriggerCtlId Integer32, failoverInfoTriggerCtlPortId PortNumber, failoverInfoTriggerCtlPortStatus INTEGER } failoverInfoTriggerCtlId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The trigger identifier." ::= { failoverInfoTriggerCtlPortEntry 1 } failoverInfoTriggerCtlPortId OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The Port identifier." ::= { failoverInfoTriggerCtlPortEntry 2 } failoverInfoTriggerCtlPortStatus OBJECT-TYPE SYNTAX INTEGER{ failed(0), operational(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Status." ::= { failoverInfoTriggerCtlPortEntry 3 } -- ---------------------------------------------------------------------------- -- } INSERT: failoverInfo -- ---------------------------------------------------------------------------- vlagInfo OBJECT IDENTIFIER ::= { layer2Info 16 } vlagInfoSystem OBJECT IDENTIFIER ::= { vlagInfo 1 } vlagInfoGroup OBJECT IDENTIFIER ::= { vlagInfo 2 } vlagInfoIslGroup OBJECT IDENTIFIER ::= { vlagInfoGroup 2 } ecpInfo OBJECT IDENTIFIER ::= { layer2Info 17 } -- VLAN group vlanMaxEnt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the VLAN configuration table." ::= { vlan 1 } vlanMaxVlanID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum allowed VLAN ID." ::= { vlan 4 } vlanCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VLAN configuration." ::= { vlan 2 } vlanCurCfgTableEntry OBJECT-TYPE SYNTAX VlanCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the VLAN configuration table." INDEX { vlanCurCfgVlanId } ::= { vlanCurCfgTable 1 } VlanCurCfgTableEntry ::= SEQUENCE { vlanCurCfgVlanId Integer32, vlanCurCfgPorts OCTET STRING, vlanCurCfgState INTEGER, vlanCurCfgStg Integer32, vlanCurCfgPrVlanType INTEGER, vlanCurCfgPrVlanMapPriId Integer32, vlanCurCfgVlanName DisplayString } vlanCurCfgVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN identifier." ::= { vlanCurCfgTableEntry 1 } vlanCurCfgPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the VLAN. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the VLAN 0 - The represented port does not belong to the VLAN" ::= { vlanCurCfgTableEntry 2 } vlanCurCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable a VLAN" ::= { vlanCurCfgTableEntry 3 } vlanCurCfgStg OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Spanning Tree Group for the VLAN." ::= { vlanCurCfgTableEntry 5 } vlanCurCfgVlanName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN name." ::= { vlanCurCfgTableEntry 9 } vlanCurCfgPrVlanType OBJECT-TYPE SYNTAX INTEGER{ none(0), primary(1), isolated(2), community(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the Private VLAN." ::= { vlanCurCfgTableEntry 10 } vlanCurCfgPrVlanMapPriId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The primary vlan id" ::= { vlanCurCfgTableEntry 11 } vlanNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VLAN configuration." ::= { vlan 3 } vlanNewCfgTableEntry OBJECT-TYPE SYNTAX VlanNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the VLAN configuration table." INDEX { vlanNewCfgVlanId } ::= { vlanNewCfgTable 1 } VlanNewCfgTableEntry ::= SEQUENCE { vlanNewCfgVlanId Integer32, vlanNewCfgVlanName DisplayString, vlanNewCfgPorts OCTET STRING, vlanNewCfgState INTEGER, vlanNewCfgAddPort PortNumber, vlanNewCfgRemovePort PortNumber, vlanNewCfgStg Integer32, vlanNewCfgPrVlanType INTEGER, vlanNewCfgPrVlanMapPriId Integer32, vlanNewCfgDelete INTEGER } vlanNewCfgVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN identifier." ::= { vlanNewCfgTableEntry 1 } vlanNewCfgVlanName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The VLAN name." ::= { vlanNewCfgTableEntry 2 } vlanNewCfgPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the VLAN. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the VLAN 0 - The represented port does not belong to the VLAN" ::= { vlanNewCfgTableEntry 3 } vlanNewCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable a VLAN" ::= { vlanNewCfgTableEntry 4 } vlanNewCfgAddPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The port to be added to the specified VLAN. A '0' value is returned when read." ::= { vlanNewCfgTableEntry 5 } vlanNewCfgRemovePort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The port to be removed from the specified VLAN. A '0' value is returned when read." ::= { vlanNewCfgTableEntry 6 } vlanNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This is an action object to create or delete a VLAN. other(1) is returned always when read. The following values are writable: delete(2)...to delete a VLAN" ::= { vlanNewCfgTableEntry 7 } vlanNewCfgStg OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The Spanning Tree Group for the VLAN." ::= { vlanNewCfgTableEntry 9 } vlanNewCfgPrVlanType OBJECT-TYPE SYNTAX INTEGER{ none(0), primary(1), isolated(2), community(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of the Private VLAN." ::= { vlanNewCfgTableEntry 13 } vlanNewCfgPrVlanMapPriId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The primary vlan id. To delete set 0." ::= { vlanNewCfgTableEntry 14 } pvlanCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PvlanCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of PROTOCOL VLAN configuration." ::= { vlan 5 } pvlanCurCfgTableEntry OBJECT-TYPE SYNTAX PvlanCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Protocol VLAN configuration table." INDEX { pvlanCurCfgVlanId, pvlanCurCfgPvlanId } ::= { pvlanCurCfgTable 1 } PvlanCurCfgTableEntry ::= SEQUENCE { pvlanCurCfgVlanId Integer32, pvlanCurCfgPvlanId Integer32, pvlanCurCfgPvlanFrameType INTEGER, pvlanCurCfgPvlanEtherType DisplayString, pvlanCurCfgPvlanPorts OCTET STRING, pvlanCurCfgPvlanPrio INTEGER, pvlanCurCfgPvlanState INTEGER, pvlanCurCfgPvlanTagPorts OCTET STRING, pvlanCurCfgPvlanPredefProto INTEGER } pvlanCurCfgVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN identifier." ::= { pvlanCurCfgTableEntry 1 } pvlanCurCfgPvlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The PVLAN identifier." ::= { pvlanCurCfgTableEntry 2 } pvlanCurCfgPvlanFrameType OBJECT-TYPE SYNTAX INTEGER{ none(0), ethernet2(1), snap(2), llc(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The frame type of the PVLAN." ::= { pvlanCurCfgTableEntry 3 } pvlanCurCfgPvlanEtherType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Ether type of the PVLAN." ::= { pvlanCurCfgTableEntry 4 } pvlanCurCfgPvlanPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the PVLAN. The ports are presented in bitmap format." ::= { pvlanCurCfgTableEntry 5 } pvlanCurCfgPvlanPrio OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The priority of the PVLAN." ::= { pvlanCurCfgTableEntry 6 } pvlanCurCfgPvlanState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable a PVLAN." ::= { pvlanCurCfgTableEntry 7 } pvlanCurCfgPvlanTagPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The list of tagged-PVLAN ports. The ports are presented in bitmap format." ::= { pvlanCurCfgTableEntry 8 } pvlanCurCfgPvlanPredefProto OBJECT-TYPE SYNTAX INTEGER { userDefined(0), decEther2(1), ipv4Ether2(2), ipv6Ether2(3), ipx802dot2(4), ipx802dot3(5), ipxEther2(6), ipxSnap(7), netbios(8), rarpEther2(9), sna802dot2(10), snaEther2(11), vinesEther2(12), xnsEther2(13) } MAX-ACCESS read-only STATUS current DESCRIPTION "A predefined Protocol (setting EtherType and FrameType to predefined values)." ::= { pvlanCurCfgTableEntry 9 } pvlanNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PvlanNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of PROTOCOL VLAN configuration." ::= { vlan 6 } pvlanNewCfgTableEntry OBJECT-TYPE SYNTAX PvlanNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Protocol VLAN configuration table." INDEX { pvlanNewCfgVlanId, pvlanNewCfgPvlanId } ::= { pvlanNewCfgTable 1 } PvlanNewCfgTableEntry ::= SEQUENCE { pvlanNewCfgVlanId Integer32, pvlanNewCfgPvlanId Integer32, pvlanNewCfgPvlanFrameType INTEGER, pvlanNewCfgPvlanEtherType DisplayString, pvlanNewCfgPvlanAddPort PortNumber, pvlanNewCfgPvlanRemovePort PortNumber, pvlanNewCfgPvlanPrio INTEGER, pvlanNewCfgPvlanState INTEGER, pvlanNewCfgPvlanTagPort PortNumber, pvlanNewCfgPvlanUntagPort PortNumber, pvlanNewCfgPvlanPorts OCTET STRING, pvlanNewCfgPvlanTagPorts OCTET STRING, pvlanNewCfgPvlanDelete INTEGER, pvlanNewCfgPvlanPredefProto INTEGER } pvlanNewCfgVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN identifier." ::= { pvlanNewCfgTableEntry 1 } pvlanNewCfgPvlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The PVLAN identifier." ::= { pvlanNewCfgTableEntry 2 } pvlanNewCfgPvlanFrameType OBJECT-TYPE SYNTAX INTEGER{ none(0), ethernet2(1), snap(2), llc(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The frame type of the PVLAN." ::= { pvlanNewCfgTableEntry 3 } pvlanNewCfgPvlanEtherType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The Ehter type of the PVLAN." ::= { pvlanNewCfgTableEntry 4 } pvlanNewCfgPvlanAddPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The port to be added to the specified PVLAN. A '0' value is returned when read." ::= { pvlanNewCfgTableEntry 5 } pvlanNewCfgPvlanRemovePort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The port to be removed to the specified PVLAN. A '0' value is returned when read." ::= { pvlanNewCfgTableEntry 6 } pvlanNewCfgPvlanPrio OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The priority of the PVLAN." ::= { pvlanNewCfgTableEntry 7 } pvlanNewCfgPvlanState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable a PVLAN" ::= { pvlanNewCfgTableEntry 8 } pvlanNewCfgPvlanTagPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The port to be tagged for the specified PVLAN. A '0' value is returned when read." ::= { pvlanNewCfgTableEntry 9 } pvlanNewCfgPvlanUntagPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The port to be untagged for the specified PVLAN. A '0' value is returned when read." ::= { pvlanNewCfgTableEntry 10 } pvlanNewCfgPvlanPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the PVLAN. The ports are presented in bitmap format." ::= { pvlanNewCfgTableEntry 11 } pvlanNewCfgPvlanTagPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The list of tagged-PVLAN ports. The ports are presented in bitmap format." ::= { pvlanNewCfgTableEntry 12 } pvlanNewCfgPvlanDelete OBJECT-TYPE SYNTAX INTEGER { delete(2), no(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete a PVLAN" ::= { pvlanNewCfgTableEntry 13 } pvlanNewCfgPvlanPredefProto OBJECT-TYPE SYNTAX INTEGER { userDefined(0), decEther2(1), ipv4Ether2(2), ipv6Ether2(3), ipx802dot2(4), ipx802dot3(5), ipxEther2(6), ipxSnap(7), netbios(8), rarpEther2(9), sna802dot2(10), snaEther2(11), vinesEther2(12), xnsEther2(13) } MAX-ACCESS read-write STATUS current DESCRIPTION "A predefined Protocol (setting EtherType and FrameType to predefined values)." ::= { pvlanNewCfgTableEntry 14 } -- Link Aggregation Control Protocol Group lacpCurSystemPriority OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "A 2-octet read-write value indicating the priority value associated with the Actor's System ID." ::= { lacp 1 } lacpNewSystemPriority OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "A 2-octet read-write value indicating the priority value associated with the Actor's System ID." ::= { lacp 2 } lacpCurSystemTimeoutTime OBJECT-TYPE SYNTAX INTEGER { short(3), long(90) } MAX-ACCESS read-only STATUS current DESCRIPTION "If a port does not receive LACPDUs for Timeout time LACP information pertaining to the port is invalidated. Its every 3 sec (short) and every 90 sec (long 3)." ::= { lacp 5 } lacpNewSystemTimeoutTime OBJECT-TYPE SYNTAX INTEGER { short(3), long(90) } MAX-ACCESS read-write STATUS current DESCRIPTION "If a port does not receive LACPDUs for Timeout time LACP information pertaining to the port is invalidated. Its every 3 sec (short) and every 90 sec (long 3)." ::= { lacp 6 } lacpCurPortCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF LacpCurPortCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LACP port configuration." ::= { lacp 7 } lacpCurPortCfgTableEntry OBJECT-TYPE SYNTAX LacpCurPortCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the LACP port configuration table." INDEX { lacpCurPortCfgTableId } ::= { lacpCurPortCfgTable 1 } LacpCurPortCfgTableEntry ::= SEQUENCE { lacpCurPortCfgTableId PortNumber, lacpCurPortState INTEGER, lacpCurPortActorPortPriority INTEGER, lacpCurPortActorAdminKey INTEGER , lacpCurPortActorMinLinks INTEGER , lacpCurPortSuspendIndividual INTEGER } lacpCurPortCfgTableId OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION " LACP port number." ::= { lacpCurPortCfgTableEntry 1 } lacpCurPortState OBJECT-TYPE SYNTAX INTEGER { off(1), active(2), passive(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port state can be one of three states off (Not participating in LACP) Active (Initiates LACPDU updates) Passive (Does not initiate LACPDU updates but responds to peer." ::= { lacpCurPortCfgTableEntry 2 } lacpCurPortActorPortPriority OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The priority value assigned to this Aggregation Port. This 16-bit value is read-only." ::= { lacpCurPortCfgTableEntry 3 } lacpCurPortActorAdminKey OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The current administrative value of the Key for the Aggregation Port. This is a 16-bit read-only value. The meaning of particular Key values is of local significance." ::= { lacpCurPortCfgTableEntry 4 } lacpCurPortActorMinLinks OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION "The current minimum links for the Aggregation Port. This is a 16-bit read-only value. The meaning of particular Key values is of local significance." ::= { lacpCurPortCfgTableEntry 5 } lacpCurPortSuspendIndividual OBJECT-TYPE SYNTAX INTEGER { suspend(1), individual(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "It indicates if the port can be treated as an individual link when it does not get LACPDU from the peer port. suspend (can't be treated as a normal link) individual (can be treated as a normal link)" ::= { lacpCurPortCfgTableEntry 6 } lacpNewPortCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF LacpNewPortCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LACP port configuration." ::= { lacp 8 } lacpNewPortCfgTableEntry OBJECT-TYPE SYNTAX LacpNewPortCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the LACP port configuration table." INDEX { lacpNewPortCfgTableId } ::= { lacpNewPortCfgTable 1 } LacpNewPortCfgTableEntry ::= SEQUENCE { lacpNewPortCfgTableId PortNumber, lacpNewPortState INTEGER, lacpNewPortActorPortPriority INTEGER, lacpNewPortActorAdminKey INTEGER, lacpNewPortActorMinLinks INTEGER, lacpNewPortSetToDefault INTEGER , lacpNewPortSuspendIndividual INTEGER } lacpNewPortCfgTableId OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION " LACP port number." ::= { lacpNewPortCfgTableEntry 1 } lacpNewPortState OBJECT-TYPE SYNTAX INTEGER { off(1), active(2), passive(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "LACP port state can be one of three states off (Not participating in LACP) Active (Initiates LACPDU updates) Passive (Does not initiate LACPDU updates but responds to peer." ::= { lacpNewPortCfgTableEntry 2 } lacpNewPortActorPortPriority OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The priority value assigned to this Aggregation Port. This 16-bit value is read-write." ::= { lacpNewPortCfgTableEntry 3 } lacpNewPortActorAdminKey OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The current administrative value of the Key for the Aggregation Port. This is a 16-bit read-write value. The meaning of particular Key values is of local significance." ::= { lacpNewPortCfgTableEntry 4 } lacpNewPortActorMinLinks OBJECT-TYPE SYNTAX INTEGER (1..8) MAX-ACCESS read-write STATUS current DESCRIPTION "The current minimum links for the Aggregation Port. This is a 16-bit read-write value. The meaning of particular Key values is of local significance." ::= { lacpNewPortCfgTableEntry 5 } lacpNewPortSetToDefault OBJECT-TYPE SYNTAX INTEGER { none(1), setDefault(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When read, always returns none(1). When setting setDefault(2) value, the LACP port settings are set to the default values." ::= { lacpNewPortCfgTableEntry 6 } lacpNewPortSuspendIndividual OBJECT-TYPE SYNTAX INTEGER { suspend(1), individual(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "It indicates if the port can be treated as an individual link when it does not get LACPDU from the peer port. suspend (can't be treated as a normal link) individual (can be treated as a normal link)" ::= { lacpNewPortCfgTableEntry 7 } lacpDeleteTrunk OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Delete a trunk with specified admin key" ::= { lacp 9 } lacpNewSystemSetToDefault OBJECT-TYPE SYNTAX INTEGER { none(1), setDefault(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When read, always returns none(1). When setting setDefault(2) value, the LACP system settings are set to the default values." ::= { lacp 10 } -- Trunk Group Group trunkGroupTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in trunk group table." ::= { trunkgroup 1 } trunkGroupCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF TrunkGroupCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of trunk group configuration." ::= { trunkgroup 2 } trunkGroupCurCfgTableEntry OBJECT-TYPE SYNTAX TrunkGroupCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the trunk group configuration table." INDEX { trunkGroupCurCfgIndex } ::= { trunkGroupCurCfgTable 1 } TrunkGroupCurCfgTableEntry ::= SEQUENCE { trunkGroupCurCfgIndex Integer32, trunkGroupCurCfgPorts OCTET STRING, trunkGroupCurCfgState INTEGER } trunkGroupCurCfgIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the trunk group." ::= { trunkGroupCurCfgTableEntry 1 } trunkGroupCurCfgPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the trunk group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the trunk group 0 - The represented port does not belong to the trunk group" ::= { trunkGroupCurCfgTableEntry 2 } trunkGroupCurCfgState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable a trunk group." ::= { trunkGroupCurCfgTableEntry 3 } trunkGroupNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF TrunkGroupNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of trunk group configuration." ::= { trunkgroup 3 } trunkGroupNewCfgTableEntry OBJECT-TYPE SYNTAX TrunkGroupNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the trunk group configuration table." INDEX { trunkGroupNewCfgIndex } ::= { trunkGroupNewCfgTable 1 } TrunkGroupNewCfgTableEntry ::= SEQUENCE { trunkGroupNewCfgIndex Integer32, trunkGroupNewCfgPorts OCTET STRING, trunkGroupNewCfgAddPort PortNumber, trunkGroupNewCfgRemovePort PortNumber, trunkGroupNewCfgState INTEGER, trunkGroupNewCfgDelete INTEGER } trunkGroupNewCfgIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the trunk group." ::= { trunkGroupNewCfgTableEntry 1 } trunkGroupNewCfgPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the trunk group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the trunk group 0 - The represented port does not belong to the trunk group" ::= { trunkGroupNewCfgTableEntry 2 } trunkGroupNewCfgAddPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The port to be added in the trunk group. When read, 0 is returned." ::= { trunkGroupNewCfgTableEntry 3 } trunkGroupNewCfgRemovePort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The port to be deleted from the trunk group. when read, 0 is returned." ::= { trunkGroupNewCfgTableEntry 4 } trunkGroupNewCfgState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable a trunk group." ::= { trunkGroupNewCfgTableEntry 5 } trunkGroupNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Setting the value to delete(2) will delete the entire row. When read, other(1) is returned." ::= { trunkGroupNewCfgTableEntry 6 } trunkLacpGroupTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in LACP trunk group table." ::= { trunkgroup 4 } trunkLacpGroupCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF TrunkLacpGroupCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LACP trunk group configuration." ::= { trunkgroup 5 } trunkLacpGroupCurCfgTableEntry OBJECT-TYPE SYNTAX TrunkLacpGroupCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the LACP trunk group configuration table." INDEX { trunkLacpGroupCurCfgIndex } ::= { trunkLacpGroupCurCfgTable 1 } TrunkLacpGroupCurCfgTableEntry ::= SEQUENCE { trunkLacpGroupCurCfgIndex Integer32, trunkLacpGroupCurCfgAdminKey Integer32 } trunkLacpGroupCurCfgIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the LACP trunk group." ::= { trunkLacpGroupCurCfgTableEntry 1 } trunkLacpGroupCurCfgAdminKey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative key of the LACP trunk group. Ports whose LACP key is same will be member ports of the trunk." ::= { trunkLacpGroupCurCfgTableEntry 2 } trunkLacpGroupNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF TrunkLacpGroupNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LACP trunk group configuration." ::= { trunkgroup 6 } trunkLacpGroupNewCfgTableEntry OBJECT-TYPE SYNTAX TrunkLacpGroupNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the LACP trunk group configuration table." INDEX { trunkLacpGroupNewCfgIndex } ::= { trunkLacpGroupNewCfgTable 1 } TrunkLacpGroupNewCfgTableEntry ::= SEQUENCE { trunkLacpGroupNewCfgIndex Integer32, trunkLacpGroupNewCfgAdminKey Integer32 } trunkLacpGroupNewCfgIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the LACP trunk group." ::= { trunkLacpGroupNewCfgTableEntry 1 } trunkLacpGroupNewCfgAdminKey OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative key of the LACP trunk group. Ports whose LACP key is same will be member ports of the trunk. Value 0 means LACP trunk group deletion." ::= { trunkLacpGroupNewCfgTableEntry 2 } -- Elmo trunk hash l2ThashCurCfgSmacState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable smac hash." ::= { thashL2 1 } l2ThashNewCfgSmacState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable smac hash." ::= { thashL2 2 } l2ThashCurCfgDmacState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable dmac hash." ::= { thashL2 3 } l2ThashNewCfgDmacState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable dmac hash." ::= { thashL2 4 } l2ThashCurCfgSipState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable sip hash." ::= { thashL2 5 } l2ThashNewCfgSipState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable sip hash." ::= { thashL2 6 } l2ThashCurCfgDipState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable dip hash." ::= { thashL2 7 } l2ThashNewCfgDipState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable dip hash." ::= { thashL2 8 } l2ThashCurCfgIngressState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable ingres port hash." ::= { thashL2 9 } l2ThashNewCfgIngressState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable ingres port hash." ::= { thashL2 10 } l2ThashCurCfgL4PortState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable L4 port hash." ::= { thashL2 11 } l2ThashNewCfgL4PortState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable L4 port hash." ::= { thashL2 12 } -- Spanning Tree Group Configuration -- This group specifies the additional configurations that are not -- covered by the Bridge MIB (RFC 1493). -- The relative Spanning Tree information can be retrieved or configured -- using Bridge MIB with an unique community string for each group specified -- in entLogicalTable of Entity MIB (RFC 2037). -- stgCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF StgCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Spanning Tree Group configuration." ::= { stgCfg 1 } stgCurCfgTableEntry OBJECT-TYPE SYNTAX StgCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Spanning Tree Group configuration." INDEX { stgCurCfgIndex } ::= { stgCurCfgTable 1 } StgCurCfgTableEntry ::= SEQUENCE { stgCurCfgIndex Integer32, stgCurCfgState INTEGER, stgCurCfgPriority INTEGER, stgCurCfgBrgHelloTime INTEGER, stgCurCfgBrgForwardDelay INTEGER, stgCurCfgBrgMaxAge INTEGER, stgCurCfgVlanBmap OCTET STRING } stgCurCfgIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB." ::= { stgCurCfgTableEntry 1 } stgCurCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Turn on of off Spanning Tree operation of a particular Spanning Tree Group." ::= { stgCurCfgTableEntry 2 } stgCurCfgPriority OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID." ::= { stgCurCfgTableEntry 5 } stgCurCfgBrgHelloTime OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The value in seconds that all bridges use for HelloTime when this bridge is acting as the root." ::= { stgCurCfgTableEntry 6 } stgCurCfgBrgForwardDelay OBJECT-TYPE SYNTAX INTEGER (4..30) MAX-ACCESS read-only STATUS current DESCRIPTION "The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root." ::= { stgCurCfgTableEntry 7 } stgCurCfgBrgMaxAge OBJECT-TYPE SYNTAX INTEGER (6..40) MAX-ACCESS read-only STATUS current DESCRIPTION "The value in seconds that all bridges use for MaxAge when this bridge is acting as the root." ::= { stgCurCfgTableEntry 8 } stgCurCfgVlanBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4096. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 9 || || || ||___ vlan 8 || |____ vlan 7 || . . . ||_________ vlan 2 |__________ vlan 1 (as index to stgCurCfgTable) where x : 1 - The represented vlan applied to the spanning tree. 0 - The represented vlan not applied to the spanning tree" ::= { stgCurCfgTableEntry 10 } stgNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF StgNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Spanning Tree Groups configuration in the new_config." ::= { stgCfg 2 } stgNewCfgTableEntry OBJECT-TYPE SYNTAX StgNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Spanning Tree Group configuration." INDEX { stgNewCfgIndex } ::= { stgNewCfgTable 1 } StgNewCfgTableEntry ::= SEQUENCE { stgNewCfgIndex Integer32, stgNewCfgState INTEGER, stgNewCfgDefaultCfg INTEGER, stgNewCfgAddVlan Integer32, stgNewCfgRemoveVlan Integer32, stgNewCfgPriority INTEGER, stgNewCfgBrgHelloTime INTEGER, stgNewCfgBrgForwardDelay INTEGER, stgNewCfgBrgMaxAge INTEGER, stgNewCfgVlanBmap OCTET STRING, stgNewCfgRemoveAllVlan INTEGER } stgNewCfgIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB." ::= { stgNewCfgTableEntry 1 } stgNewCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Turn on of off Spanning Tree operation of a particular Spanning Tree Group." ::= { stgNewCfgTableEntry 2 } stgNewCfgDefaultCfg OBJECT-TYPE SYNTAX INTEGER { default-config(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the value to default-config(1) will set the default configuration as recommended by IEEE 802.1D for a particular Spanning Tree Group. default-config (1) is always returned When read, but it does not mean anything." ::= { stgNewCfgTableEntry 3 } stgNewCfgAddVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The vlan to be added to the specified Spanning Tree Group. A '0' value is returned when read." ::= {stgNewCfgTableEntry 4 } stgNewCfgRemoveVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The vlan to be removed from the specified Spanning Tree Group. A '0' value is returned when read." ::= { stgNewCfgTableEntry 5 } stgNewCfgPriority OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID." ::= { stgNewCfgTableEntry 8 } stgNewCfgBrgHelloTime OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The value in seconds that all bridges use for HelloTime when this bridge is acting as the root." ::= { stgNewCfgTableEntry 9 } stgNewCfgBrgForwardDelay OBJECT-TYPE SYNTAX INTEGER (4..30) MAX-ACCESS read-write STATUS current DESCRIPTION "The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root." ::= { stgNewCfgTableEntry 10 } stgNewCfgBrgMaxAge OBJECT-TYPE SYNTAX INTEGER (6..40) MAX-ACCESS read-write STATUS current DESCRIPTION "The value in seconds that all bridges use for MaxAge when this bridge is acting as the root." ::= { stgNewCfgTableEntry 11 } stgNewCfgVlanBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vlans applied to the spanning tree group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4096. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 9 || || || ||___ vlan 8 || |____ vlan 7 || . . . ||_________ vlan 2 |__________ vlan 1 (as index to stgCurCfgTable) where x : 1 - The represented vlan applied to the spanning tree. 0 - The represented vlan not applied to the spanning tree" ::= { stgNewCfgTableEntry 13 } stgNewCfgRemoveAllVlan OBJECT-TYPE SYNTAX INTEGER { default-config(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The all vlans to be removed from the specified Spanning Tree Group. A '0' value is returned when read." ::= { stgNewCfgTableEntry 14 } stgCurCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF StgCurCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Spanning Tree Group port configuration in the current_config." ::= { stgCfg 3 } stgCurCfgPortTableEntry OBJECT-TYPE SYNTAX StgCurCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about port configuration of a particular Spanning Tree Group." INDEX { stgCurCfgStgIndex, stgCurCfgPortIndex } ::= { stgCurCfgPortTable 1 } StgCurCfgPortTableEntry ::= SEQUENCE { stgCurCfgStgIndex Integer32, stgCurCfgPortIndex PortNumber, stgCurCfgPortPriority INTEGER, stgCurCfgPortPathCost Integer32, stgCurCfgPortState INTEGER } stgCurCfgStgIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB." ::= { stgCurCfgPortTableEntry 1 } stgCurCfgPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier of a particular Spanning Tree Group." ::= { stgCurCfgPortTableEntry 2 } stgCurCfgPortState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Turn on of off Spanning Tree operation of a particular port of a Spanning Tree Group." ::= { stgCurCfgPortTableEntry 3 } stgCurCfgPortPriority OBJECT-TYPE SYNTAX INTEGER (0..240) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID." ::= { stgCurCfgPortTableEntry 4 } stgCurCfgPortPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the spanning tree root which include this port ( range is (0..200000000) )." ::= { stgCurCfgPortTableEntry 5 } stgNewCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF StgNewCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Spanning Tree Group port configuration in the new_config." ::= { stgCfg 4 } stgNewCfgPortTableEntry OBJECT-TYPE SYNTAX StgNewCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about port configuration of a particular Spanning Tree Group." INDEX { stgNewCfgStgIndex, stgNewCfgPortIndex } ::= { stgNewCfgPortTable 1 } StgNewCfgPortTableEntry ::= SEQUENCE { stgNewCfgStgIndex Integer32, stgNewCfgPortIndex PortNumber, stgNewCfgPortPriority INTEGER, stgNewCfgPortPathCost Integer32, stgNewCfgPortState INTEGER } stgNewCfgStgIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB." ::= { stgNewCfgPortTableEntry 1 } stgNewCfgPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier of a particular Spanning Tree Group." ::= { stgNewCfgPortTableEntry 2 } stgNewCfgPortState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Turn on of off Spanning Tree operation of a particular port of a Spanning Tree Group." ::= { stgNewCfgPortTableEntry 3 } stgNewCfgPortPriority OBJECT-TYPE SYNTAX INTEGER (0..240) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID." ::= { stgNewCfgPortTableEntry 4 } stgNewCfgPortPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the spanning tree root which include this port ( range is (0..200000000) )." ::= { stgNewCfgPortTableEntry 5 } -- Complete Port Mirroring pmCurCfgPortMirrState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of port-based port mirroring." ::= { mirrPortMirr 1 } pmNewCfgPortMirrState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The state of port-based port mirroring." ::= { mirrPortMirr 2 } pmCurCfgPortMonitorTable OBJECT-TYPE SYNTAX SEQUENCE OF PmCurCfgPortMonitorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of monitoring ports." ::= { mirrPortMirr 3 } pmCurCfgPortMonitorEntry OBJECT-TYPE SYNTAX PmCurCfgPortMonitorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the monitoring port table." INDEX { pmCurCfgPmirrMoniPortIndex, pmCurCfgPmirrMirrPortIndex } ::= { pmCurCfgPortMonitorTable 1 } PmCurCfgPortMonitorEntry ::= SEQUENCE { pmCurCfgPmirrMoniPortIndex PortNumber, pmCurCfgPmirrMirrPortIndex PortNumber, pmCurCfgPmirrDirection INTEGER } pmCurCfgPmirrMoniPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The monitoring port number." ::= { pmCurCfgPortMonitorEntry 1 } pmCurCfgPmirrMirrPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The mirrored port number" ::= { pmCurCfgPortMonitorEntry 2 } pmCurCfgPmirrDirection OBJECT-TYPE SYNTAX INTEGER { in(1), out(2), both(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of traffic to be monitored with respect to the mirrored port." ::= { pmCurCfgPortMonitorEntry 3 } pmNewCfgPortMonitorTable OBJECT-TYPE SYNTAX SEQUENCE OF PmNewCfgPortMonitorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of monitoring ports." ::= { mirrPortMirr 4 } pmNewCfgPortMonitorEntry OBJECT-TYPE SYNTAX PmNewCfgPortMonitorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the monitoring port table." INDEX { pmNewCfgPmirrMoniPortIndex, pmNewCfgPmirrMirrPortIndex } ::= { pmNewCfgPortMonitorTable 1 } PmNewCfgPortMonitorEntry ::= SEQUENCE { pmNewCfgPmirrMoniPortIndex PortNumber, pmNewCfgPmirrMirrPortIndex PortNumber, pmNewCfgPmirrDirection INTEGER, pmNewCfgPmirrDelete INTEGER, pmNewCfgPmonDelete INTEGER } pmNewCfgPmirrMoniPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The monitoring port number." ::= { pmNewCfgPortMonitorEntry 1 } pmNewCfgPmirrMirrPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The mirrored port number" ::= { pmNewCfgPortMonitorEntry 2 } pmNewCfgPmirrDirection OBJECT-TYPE SYNTAX INTEGER { in(1), out(2), both(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of traffic to be monitored with respect to the mirrored port." ::= { pmNewCfgPortMonitorEntry 3 } pmNewCfgPmirrDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Setting the value to delete(2) will delete the entire row. When read, other(1) is returned." ::= { pmNewCfgPortMonitorEntry 4 } pmNewCfgPmonDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Setting the value to delete(2) will delete the monitor port. When read, other(1) is returned." ::= { pmNewCfgPortMonitorEntry 10 } -- MST Configuration mstCurCfgRegionName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Name for the Region's configuration." ::= { mstGeneralCfg 3 } mstNewCfgRegionName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Name for the Region's configuration." ::= { mstGeneralCfg 4 } mstCurCfgRegionRevision OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Revision of the MST Region." ::= { mstGeneralCfg 5 } mstNewCfgRegionRevision OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Revision of the MST Region." ::= { mstGeneralCfg 6 } mstCurCfgMaxHopCount OBJECT-TYPE SYNTAX INTEGER (4..60) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum hop count value." ::= { mstGeneralCfg 7 } mstNewCfgMaxHopCount OBJECT-TYPE SYNTAX INTEGER (4..60) MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the maximum hop count value." ::= { mstGeneralCfg 8 } mstCurCfgStpMode OBJECT-TYPE SYNTAX INTEGER { mstp(1), rstp(2), pvrst(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The version of Spanning Tree Protocal the bridge is currently running." ::= { mstGeneralCfg 9 } mstNewCfgStpMode OBJECT-TYPE SYNTAX INTEGER { mstp(1), rstp(2), pvrst(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The version of Spanning Tree Protocal the bridge is currently running." ::= { mstGeneralCfg 10 } mstCistDefaultCfg OBJECT-TYPE SYNTAX INTEGER { default(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the value to default(1) will set the Multiple Spanning Tree and member parameters to default. default(1) is always returned when read, but it does not mean anything." ::= { mstCistCfg 1 } -- CIST Brige Configuration mstCistBridgeCfg OBJECT IDENTIFIER ::= { mstCistCfg 2 } mstCistCurCfgBridgePriority OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the writable portion of the Brigde Identifier comprising of the first two octets." ::= { mstCistBridgeCfg 1 } mstCistNewCfgBridgePriority OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the writable portion of the Brigde Identifier comprising of the first two octets." ::= { mstCistBridgeCfg 2 } mstCistCurCfgBridgeMaxAge OBJECT-TYPE SYNTAX INTEGER (6..40) MAX-ACCESS read-only STATUS current DESCRIPTION "The value in seconds that all bridges use for MaxAge when this bridge is acting as the root." ::= { mstCistBridgeCfg 5 } mstCistNewCfgBridgeMaxAge OBJECT-TYPE SYNTAX INTEGER (6..40) MAX-ACCESS read-write STATUS current DESCRIPTION "The value in seconds that all bridges use for MaxAge when this bridge is acting as the root." ::= { mstCistBridgeCfg 6 } mstCistCurCfgBridgeForwardDelay OBJECT-TYPE SYNTAX INTEGER (4..30) MAX-ACCESS read-only STATUS current DESCRIPTION "The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root." ::= { mstCistBridgeCfg 7 } mstCistNewCfgBridgeForwardDelay OBJECT-TYPE SYNTAX INTEGER (4..30) MAX-ACCESS read-write STATUS current DESCRIPTION "The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root." ::= { mstCistBridgeCfg 8 } mstCistCurCfgVlanBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vlans applied to the CIST group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4094. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 9 || || || ||___ vlan 8 || |____ vlan 7 || . . . ||_________ vlan 2 |__________ vlan 1 where x : 1 - The represented vlan applied to the CIST group. 0 - The represented vlan not applied to the group" ::= { mstCistBridgeCfg 9 } mstCistNewCfgVlanBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vlans applied to the CIST group. The vlans are presented in bitmap format. This string displays vlan number from 1 to 4094. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vlan 9 || || || ||___ vlan 8 || |____ vlan 7 || . . . ||_________ vlan 2 |__________ vlan 1 where x : 1 - The represented vlan applied to the CIST group. 0 - The represented vlan not applied to the group" ::= { mstCistBridgeCfg 10 } mstCistNewCfgAddVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The vlan to be added to the CIST Group. A '0' value is returned when read." ::= { mstCistBridgeCfg 11 } -- CIST Port Configuration mstCistCurCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MstCistCurCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of CIST Port configuration." ::= { mstCistCfg 3 } mstCistCurCfgPortTableEntry OBJECT-TYPE SYNTAX MstCistCurCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular CIST Port configuration." INDEX { mstCistCurCfgPortIndex } ::= { mstCistCurCfgPortTable 1 } MstCistCurCfgPortTableEntry ::= SEQUENCE { mstCistCurCfgPortIndex PortNumber, mstCistCurCfgPortPriority INTEGER, mstCistCurCfgPortPathCost INTEGER, mstCistCurCfgPortLinkType INTEGER, mstCistCurCfgPortEdge INTEGER, mstCistCurCfgPortStpState INTEGER, mstCistCurCfgPortHelloTime INTEGER , mstCistCurCfgPortPvstProtection INTEGER } mstCistCurCfgPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the port for which this entry contains spanning tree configuration." ::= { mstCistCurCfgPortTableEntry 1 } mstCistCurCfgPortPriority OBJECT-TYPE SYNTAX INTEGER (0..240) MAX-ACCESS read-only STATUS current DESCRIPTION "The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value." ::= { mstCistCurCfgPortTableEntry 2 } mstCistCurCfgPortPathCost OBJECT-TYPE SYNTAX INTEGER (0..200000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the CIST Root which include this port." ::= { mstCistCurCfgPortTableEntry 3 } mstCistCurCfgPortLinkType OBJECT-TYPE SYNTAX INTEGER { auto(1), p2p(2), shared(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative point-to-point status of the LAN segment attached to this port. A value of p2p (2) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of shared(3) indicates that this port should be treated as having a shared media connection. A value of auto(1) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means. (for MSTP only)" ::= { mstCistCurCfgPortTableEntry 4 } mstCistCurCfgPortEdge OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the Edge Port parameter. (for MSTP only)" ::= { mstCistCurCfgPortTableEntry 5 } mstCistCurCfgPortStpState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Turn port's Spanning Tree on/off." ::= { mstCistCurCfgPortTableEntry 6 } mstCistCurCfgPortHelloTime OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time between the transmission of Configuration Port PDUs in seconds." ::= { mstCistCurCfgPortTableEntry 7 } mstCistCurCfgPortPvstProtection OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the PVST Protection parameter." ::= { mstCistCurCfgPortTableEntry 8 } mstCistNewCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MstCistNewCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of CIST Port configuration." ::= { mstCistCfg 4 } mstCistNewCfgPortTableEntry OBJECT-TYPE SYNTAX MstCistNewCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular CIST Port configuration." INDEX { mstCistNewCfgPortIndex } ::= { mstCistNewCfgPortTable 1 } MstCistNewCfgPortTableEntry ::= SEQUENCE { mstCistNewCfgPortIndex PortNumber, mstCistNewCfgPortPriority INTEGER, mstCistNewCfgPortPathCost INTEGER, mstCistNewCfgPortStpState INTEGER, mstCistNewCfgPortHelloTime INTEGER , mstCistNewCfgPortPvstProtection INTEGER } mstCistNewCfgPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the port for which this entry contains spanning tree configuration." ::= { mstCistNewCfgPortTableEntry 1 } mstCistNewCfgPortPriority OBJECT-TYPE SYNTAX INTEGER (0..240) MAX-ACCESS read-write STATUS current DESCRIPTION "The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value." ::= { mstCistNewCfgPortTableEntry 2 } mstCistNewCfgPortPathCost OBJECT-TYPE SYNTAX INTEGER (0..200000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the CIST Root which include this port." ::= { mstCistNewCfgPortTableEntry 3 } mstCistNewCfgPortStpState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Turn port's Spanning Tree on/off." ::= { mstCistNewCfgPortTableEntry 6 } mstCistNewCfgPortHelloTime OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time between the transmission of Configuration Port PDUs in seconds." ::= { mstCistNewCfgPortTableEntry 7 } mstCistNewCfgPortPvstProtection OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The value of the PVST Protection parameter." ::= { mstCistNewCfgPortTableEntry 8 } -- L2 general pvstCompatibilityCurCfgState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable PVST+ compatibility" ::= { l2GeneralCfg 9 } pvstCompatibilityNewCfgState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable PVST+ compatibility" ::= { l2GeneralCfg 10 } nostpCurCfgState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "STP Mode Disable global state." ::= { l2GeneralCfg 11 } nostpNewCfgState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable STP Mode Disable." ::= { l2GeneralCfg 12 } stpLoopGuardCurCfgState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "STP loop guard global state." ::= { l2GeneralCfg 13 } stpLoopGuardNewCfgState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable STP loop guard." ::= { l2GeneralCfg 14 } vlanAutoStgCurCfgState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN automatic STG assignment global state." ::= { l2GeneralCfg 15 } vlanAutoStgNewCfgState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable VLAN automatic STG assignment." ::= { l2GeneralCfg 16 } -- -- { LLDP Port Table -- lldpPortTableMaxEnt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the port configuration host table." ::= { lldpCfg 1 } lldpCurCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpCurCfgPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LLDP port configuration in the current_configuration block." ::= { lldpCfg 2 } lldpCurCfgPortEntry OBJECT-TYPE SYNTAX LldpCurCfgPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the LLDP port configuration table in the current_configuration block." INDEX { lldpCurCfgPortIndx } ::= { lldpCurCfgPortTable 1 } LldpCurCfgPortEntry ::= SEQUENCE { lldpCurCfgPortIndx PortNumber, lldpCurCfgPortAdmStat INTEGER, lldpCurCfgPortSnmpTrap INTEGER ,lldpCurCfgPortportdesctlv INTEGER ,lldpCurCfgPortsysnametlv INTEGER ,lldpCurCfgPortsysdescrtlv INTEGER ,lldpCurCfgPortsyscaptlv INTEGER ,lldpCurCfgPortmgmtaddrtlv INTEGER ,lldpCurCfgPortportvidtlv INTEGER ,lldpCurCfgPortportprottlv INTEGER ,lldpCurCfgPortvlannametlv INTEGER ,lldpCurCfgPortprotidtlv INTEGER ,lldpCurCfgPortmacphytlv INTEGER ,lldpCurCfgPortpowermditlv INTEGER ,lldpCurCfgPortlinkaggrtlv INTEGER ,lldpCurCfgPortframesztlv INTEGER ,lldpCurCfgPortevbtlv INTEGER } lldpCurCfgPortIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the row in LLDP port configurations table." ::= { lldpCurCfgPortEntry 1 } lldpCurCfgPortAdmStat OBJECT-TYPE SYNTAX INTEGER { enabledTxOnly(1), enabledRxOnly(2), enabledRxTx(3), disabled(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the admin status of the LLDP port." ::= { lldpCurCfgPortEntry 2 } lldpCurCfgPortSnmpTrap OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the SNMP trap notification state of the LLDP port." ::= { lldpCurCfgPortEntry 3 } lldpCurCfgPortportdesctlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Port Description TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 4 } lldpCurCfgPortsysnametlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the System Name TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 5 } lldpCurCfgPortsysdescrtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the System Description TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 6 } lldpCurCfgPortsyscaptlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the System Capabilities TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 7 } lldpCurCfgPortmgmtaddrtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Management Address TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 8 } lldpCurCfgPortportvidtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Port VLAN ID TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 9 } lldpCurCfgPortportprottlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Port and Protocol VLAN ID TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 10 } lldpCurCfgPortvlannametlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the VLAN Name TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 11 } lldpCurCfgPortprotidtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Protocol Identity TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 12 } lldpCurCfgPortmacphytlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the MAC/PHY Configuration/Status TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 13 } lldpCurCfgPortpowermditlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Power Via MDI TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 14 } lldpCurCfgPortlinkaggrtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Link Aggregation TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 15 } lldpCurCfgPortframesztlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Maximum Frame Size TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 16 } lldpCurCfgPortevbtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the EVB TLV state of the LLDP port." ::= { lldpCurCfgPortEntry 18 } lldpNewCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpNewCfgPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LLDP port configuration in the new_configuration block." ::= { lldpCfg 3 } lldpNewCfgPortEntry OBJECT-TYPE SYNTAX LldpNewCfgPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the LLDP port configuration table in the new_configuration block." INDEX { lldpNewCfgPortIndx } ::= { lldpNewCfgPortTable 1 } LldpNewCfgPortEntry ::= SEQUENCE { lldpNewCfgPortIndx PortNumber, lldpNewCfgPortAdmStat INTEGER, lldpNewCfgPortSnmpTrap INTEGER ,lldpNewCfgPortportdesctlv INTEGER ,lldpNewCfgPortsysnametlv INTEGER ,lldpNewCfgPortsysdescrtlv INTEGER ,lldpNewCfgPortsyscaptlv INTEGER ,lldpNewCfgPortmgmtaddrtlv INTEGER ,lldpNewCfgPortportvidtlv INTEGER ,lldpNewCfgPortportprottlv INTEGER ,lldpNewCfgPortvlannametlv INTEGER ,lldpNewCfgPortprotidtlv INTEGER ,lldpNewCfgPortmacphytlv INTEGER ,lldpNewCfgPortpowermditlv INTEGER ,lldpNewCfgPortlinkaggrtlv INTEGER ,lldpNewCfgPortframesztlv INTEGER ,lldpNewCfgPortalltlv INTEGER } lldpNewCfgPortIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the row in LLDP port configurations table." ::= { lldpNewCfgPortEntry 1 } lldpNewCfgPortAdmStat OBJECT-TYPE SYNTAX INTEGER { enabledTxOnly(1), enabledRxOnly(2), enabledRxTx(3), disabled(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the admin status of the LLDP port." ::= { lldpNewCfgPortEntry 2 } lldpNewCfgPortSnmpTrap OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the SNMP trap notification state of the LLDP port" ::= { lldpNewCfgPortEntry 3 } lldpNewCfgPortportdesctlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the Port Description TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 4 } lldpNewCfgPortsysnametlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the System Name TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 5 } lldpNewCfgPortsysdescrtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the System Description TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 6 } lldpNewCfgPortsyscaptlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the System Capabilities TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 7 } lldpNewCfgPortmgmtaddrtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the Management Address TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 8 } lldpNewCfgPortportvidtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the Port VLAN ID TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 9 } lldpNewCfgPortportprottlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the Port and Protocol VLAN ID TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 10 } lldpNewCfgPortvlannametlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the VLAN Name TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 11 } lldpNewCfgPortprotidtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the Protocol Identity TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 12 } lldpNewCfgPortmacphytlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the MAC/PHY Configuration/Status TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 13 } lldpNewCfgPortpowermditlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the Power Via MDI TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 14 } lldpNewCfgPortlinkaggrtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the Link Aggregation TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 15 } lldpNewCfgPortframesztlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the Maximum Frame Size TLV state of the LLDP port." ::= { lldpNewCfgPortEntry 16 } lldpNewCfgPortalltlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), other(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set the corresponding state for all the LLDP port's TLVs. other(3) is returned when the object is read." ::= { lldpNewCfgPortEntry 17 } -- -- } End of LLDP Port Table -- -- -- { LLDP General Table -- lldpGeneral OBJECT IDENTIFIER ::= { lldpCfg 4 } lldpCurCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP global state." ::= { lldpGeneral 1 } lldpNewCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Globally turn LLDP on or off." ::= { lldpGeneral 2 } lldpCurCfgMsgTxInt OBJECT-TYPE SYNTAX INTEGER (5..32768) MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP message transmission interval for LLDPDU." ::= { lldpGeneral 3 } lldpNewCfgMsgTxInt OBJECT-TYPE SYNTAX INTEGER (5..32768) MAX-ACCESS read-write STATUS current DESCRIPTION "LLDP message transmission interval for LLDPDU." ::= { lldpGeneral 4 } lldpCurCfgMsgTxHld OBJECT-TYPE SYNTAX INTEGER (2..10) MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP message transmission holdtime-multiplier." ::= { lldpGeneral 5 } lldpNewCfgMsgTxHld OBJECT-TYPE SYNTAX INTEGER (2..10) MAX-ACCESS read-write STATUS current DESCRIPTION "LLDP message transmission holdtime-multiplier." ::= { lldpGeneral 6 } lldpCurCfgNotifInt OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP minimum SNMP trap notification interval." ::= { lldpGeneral 7 } lldpNewCfgNotifInt OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "LLDP minimum SNMP trap notification interval." ::= { lldpGeneral 8 } lldpCurCfgTxDelay OBJECT-TYPE SYNTAX INTEGER (1..8192) MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP delay interval between advertisements." ::= { lldpGeneral 9 } lldpNewCfgTxDelay OBJECT-TYPE SYNTAX INTEGER (1..8192) MAX-ACCESS read-write STATUS current DESCRIPTION "LLDP delay interval between advertisements." ::= { lldpGeneral 10 } lldpCurCfgReinitDelay OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "LLDP reinit delay interval." ::= { lldpGeneral 11 } lldpNewCfgReinitDelay OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "LLDP reinit delay interval." ::= { lldpGeneral 12 } -- -- } End of LLDP General Table -- -- -- { LLDP Statistics -- lldpStatsTableMaxEnt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the statistics host table." ::= { lldpStats 1 } lldpStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LLDP statistics." ::= { lldpStats 2 } lldpStatsClearAll OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(2) results in clearing the LLDP statistics for all the ports." ::= { lldpStats 3 } lldpStatsTableEntry OBJECT-TYPE SYNTAX LldpStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP statistics info." INDEX { lldpStatsIndex } ::= { lldpStatsTable 1 } LldpStatsTableEntry ::= SEQUENCE { lldpStatsIndex PortNumber, lldpStatsFramesOutTotal Counter32, lldpStatsFramesInTotal Counter32, lldpStatsFramesInErrorsTotal Counter32, lldpStatsFramesDiscardedTotal Counter32, lldpStatsTLVsUnrecognizedTotal Counter32, lldpStatsAgeoutsTotal Counter32, lldpStatsClear INTEGER } lldpStatsIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the row in LLDP port statistics." ::= { lldpStatsTableEntry 1 } lldpStatsFramesOutTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of LLDP frames transmitted in this port." ::= { lldpStatsTableEntry 2 } lldpStatsFramesInTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of LLDP frames received in this port." ::= { lldpStatsTableEntry 3 } lldpStatsFramesInErrorsTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of erroneous LLDP frames received in this port." ::= { lldpStatsTableEntry 4 } lldpStatsFramesDiscardedTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received LLDP frames discarded in this port." ::= { lldpStatsTableEntry 5 } lldpStatsTLVsUnrecognizedTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of unrecognized TLVs in this port." ::= { lldpStatsTableEntry 6 } lldpStatsAgeoutsTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of neighbor's information deleted in this port." ::= { lldpStatsTableEntry 7 } lldpStatsClear OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(2) results in clearing the LLDP statistics." ::= { lldpStatsTableEntry 8 } -- -- } End of LLDP Statistics -- -- -- { LLDP Info -- lldpInfoPortTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpInfoPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LLDP Port Info." ::= { lldpInfo 1 } lldpInfoPortEntry OBJECT-TYPE SYNTAX LldpInfoPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP Port Info." INDEX { lldpInfoPortIndex } ::= { lldpInfoPortTable 1 } LldpInfoPortEntry ::= SEQUENCE { lldpInfoPortIndex PortNumber, lldpInfoPortAlias DisplayString, lldpInfoPortMacAddress PhysAddress, lldpInfoPortMtu Integer32, lldpInfoPortEnabled INTEGER, lldpInfoPortAdminStatus INTEGER, lldpInfoPortRxChanges INTEGER ,lldpInfoPortportdesctlv INTEGER ,lldpInfoPortsysnametlv INTEGER ,lldpInfoPortsysdescrtlv INTEGER ,lldpInfoPortsyscaptlv INTEGER ,lldpInfoPortmgmtaddrtlv INTEGER ,lldpInfoPortportvidtlv INTEGER ,lldpInfoPortportprottlv INTEGER ,lldpInfoPortvlannametlv INTEGER ,lldpInfoPortprotidtlv INTEGER ,lldpInfoPortmacphytlv INTEGER ,lldpInfoPortpowermditlv INTEGER ,lldpInfoPortlinkaggrtlv INTEGER ,lldpInfoPortframesztlv INTEGER ,lldpInfoPortevbtlv INTEGER } lldpInfoPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the row in LLDP info port table." ::= { lldpInfoPortEntry 1 } lldpInfoPortAlias OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port alias of the port in LLDP info port table." ::= { lldpInfoPortEntry 2 } lldpInfoPortMacAddress OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The mac address of the port in LLDP info port table." ::= { lldpInfoPortEntry 3 } lldpInfoPortMtu OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MTU size of the port in LLDP info port table." ::= { lldpInfoPortEntry 4 } lldpInfoPortEnabled OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The PortEnabled field of the port in LLDP info port table." ::= { lldpInfoPortEntry 5 } lldpInfoPortAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabledTxOnly(1), enabledRxOnly(2), enabledRxTx(3), disabled(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Admin Status of the port in LLDP info port table." ::= { lldpInfoPortEntry 6 } lldpInfoPortRxChanges OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The rxChanges field of the port in LLDP info port table." ::= { lldpInfoPortEntry 7 } lldpInfoPortportdesctlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Port Description TLV state of the LLDP port." ::= { lldpInfoPortEntry 8 } lldpInfoPortsysnametlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the System Name TLV state of the LLDP port." ::= { lldpInfoPortEntry 9 } lldpInfoPortsysdescrtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the System Description TLV state of the LLDP port." ::= { lldpInfoPortEntry 10 } lldpInfoPortsyscaptlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the System Capabilities TLV state of the LLDP port." ::= { lldpInfoPortEntry 11 } lldpInfoPortmgmtaddrtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Management Address TLV state of the LLDP port." ::= { lldpInfoPortEntry 12 } lldpInfoPortportvidtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Port VLAN ID TLV state of the LLDP port." ::= { lldpInfoPortEntry 13 } lldpInfoPortportprottlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Port and Protocol VLAN ID TLV state of the LLDP port." ::= { lldpInfoPortEntry 14 } lldpInfoPortvlannametlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the VLAN Name TLV state of the LLDP port." ::= { lldpInfoPortEntry 15 } lldpInfoPortprotidtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Protocol Identity TLV state of the LLDP port." ::= { lldpInfoPortEntry 16 } lldpInfoPortmacphytlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the MAC/PHY Configuration/Status TLV state of the LLDP port." ::= { lldpInfoPortEntry 17 } lldpInfoPortpowermditlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Power Via MDI TLV state of the LLDP port." ::= { lldpInfoPortEntry 18 } lldpInfoPortlinkaggrtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Link Aggregation TLV state of the LLDP port." ::= { lldpInfoPortEntry 19 } lldpInfoPortframesztlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Maximum Frame Size TLV state of the LLDP port." ::= { lldpInfoPortEntry 20 } lldpInfoPortevbtlv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the EVB TLV state of the LLDP port." ::= { lldpInfoPortEntry 22 } lldpInfoTxTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpInfoTxEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LLDP Transmit State Machine Info." ::= { lldpInfo 2 } lldpInfoTxEntry OBJECT-TYPE SYNTAX LldpInfoTxEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP Transmit State Machine Info." INDEX { lldpInfoTxIndex } ::= { lldpInfoTxTable 1 } LldpInfoTxEntry ::= SEQUENCE { lldpInfoTxIndex PortNumber, lldpInfoTxState INTEGER, lldpInfoTxLocalChanged INTEGER, lldpInfoTxTTL Integer32, lldpInfoTxTxTTR Integer32, lldpInfoTxDelayWhile Integer32, lldpInfoTxShutdownWhile Integer32, lldpInfoTxReinitDelay Integer32, lldpInfoTxHoldMultiplier Integer32, lldpInfoTxTransmitInterval Integer32, lldpInfoTxTransmitDelay Integer32, lldpInfoTxDMAC DisplayString } lldpInfoTxIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the row in LLDP Transmit State Machine info table." ::= { lldpInfoTxEntry 1 } lldpInfoTxState OBJECT-TYPE SYNTAX INTEGER { txLldpInitialize(1), txIdle(2), txShutdownFrame(3), txInfoFrame(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The transmit state of the port in LLDP Transmit State Machine." ::= { lldpInfoTxEntry 2 } lldpInfoTxLocalChanged OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The somethingChangedLocal field of the port in LLDP Transmit State Machine." ::= { lldpInfoTxEntry 3 } lldpInfoTxTTL OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The txTTL timer of the port in LLDP Transmit State Machine." ::= { lldpInfoTxEntry 4 } lldpInfoTxTxTTR OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The txTTR timer of the port in LLDP Transmit State Machine." ::= { lldpInfoTxEntry 5 } lldpInfoTxDelayWhile OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The txDelayWhile timer of the port in LLDP Transmit State Machine." ::= { lldpInfoTxEntry 6 } lldpInfoTxShutdownWhile OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The txShutdownWhile timer of the port in LLDP Transmit State Machine." ::= { lldpInfoTxEntry 7 } lldpInfoTxReinitDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The reinitDelay timer of the port in LLDP Transmit State Machine." ::= { lldpInfoTxEntry 8 } lldpInfoTxHoldMultiplier OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The msgTxHold timer of the port in LLDP Transmit State Machine." ::= { lldpInfoTxEntry 9 } lldpInfoTxTransmitInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The msgTxInterval timer of the port in LLDP Transmit State Machine." ::= { lldpInfoTxEntry 10 } lldpInfoTxTransmitDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The txDelay timer of the port in LLDP Transmit State Machine." ::= { lldpInfoTxEntry 11 } lldpInfoTxDMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Destination MAC address of the LLDP remote devices. Legend(possible values in DMAC column) : NB - Nearest Bridge - 01-80-C2-00-00-0E NnTB - Nearest non-TPMR Bridge - 01-80-C2-00-00-03 NCB - Nearest Customer Bridge - 01-80-C2-00-00-00" ::= { lldpInfoTxEntry 12 } lldpInfoRxTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpInfoRxEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LLDP Receive State Machine Info." ::= { lldpInfo 3 } lldpInfoRxEntry OBJECT-TYPE SYNTAX LldpInfoRxEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP Receive State Machine Info." INDEX { lldpInfoRxIndex } ::= { lldpInfoRxTable 1 } LldpInfoRxEntry ::= SEQUENCE { lldpInfoRxIndex PortNumber, lldpInfoRxState INTEGER, lldpInfoRxBadFrame INTEGER, lldpInfoRxRcvFrame INTEGER, lldpInfoRxRxInfoAge INTEGER, lldpInfoRxRemoteChanged INTEGER, lldpInfoRxTooManyNeighbors INTEGER, lldpInfoRxSNMPNotify INTEGER, lldpInfoRxRxTTL Integer32, lldpInfoRxTooManyNeighborTimer Integer32, lldpInfoRxDMAC DisplayString } lldpInfoRxIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the row in LLDP Receive State Machine info table." ::= { lldpInfoRxEntry 1 } lldpInfoRxState OBJECT-TYPE SYNTAX INTEGER { lldpWaitPortOperational(1), deleteAgedInfo(2), rxLldpInitialize(3), rxWaitForFrame(4), rxFrame(5), deleteInfo(6), updateInfo(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The receive state of the port in LLDP Receive State Machine." ::= { lldpInfoRxEntry 2 } lldpInfoRxBadFrame OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The badFrame field of the port in LLDP Receive State Machine." ::= { lldpInfoRxEntry 3 } lldpInfoRxRcvFrame OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The rcvFrame field of the port in LLDP Receive State Machine." ::= { lldpInfoRxEntry 4 } lldpInfoRxRxInfoAge OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The rxInfoAge field of the port in LLDP Receive State Machine." ::= { lldpInfoRxEntry 5 } lldpInfoRxRemoteChanged OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The somethingChangedRemote field of the port in LLDP Receive State Machine." ::= { lldpInfoRxEntry 6 } lldpInfoRxTooManyNeighbors OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The tooManyNeighbors field of the port in LLDP Receive State Machine." ::= { lldpInfoRxEntry 7 } lldpInfoRxSNMPNotify OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The tooManyNeighbors field of the port in LLDP Receive State Machine." ::= { lldpInfoRxEntry 8 } lldpInfoRxRxTTL OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The rxTTL timer of the port in LLDP Receive State Machine." ::= { lldpInfoRxEntry 9 } lldpInfoRxTooManyNeighborTimer OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The tooManyNeighborsTimer timer of the port in LLDP Receive State Machine." ::= { lldpInfoRxEntry 10 } lldpInfoRxDMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Destination MAC address of the LLDP remote devices. Legend(possible values in DMAC column) : NB - Nearest Bridge - 01-80-C2-00-00-0E NnTB - Nearest non-TPMR Bridge - 01-80-C2-00-00-03 NCB - Nearest Customer Bridge - 01-80-C2-00-00-00" ::= { lldpInfoRxEntry 11 } lldpInfoRemoteDevicesTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpInfoRemoteDevicesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LLDP remote devices Info." ::= { lldpInfo 4 } lldpInfoRemoteDevicesEntry OBJECT-TYPE SYNTAX LldpInfoRemoteDevicesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP remote devices Info." INDEX { lldpInfoRemoteDevicesIndex } ::= { lldpInfoRemoteDevicesTable 1 } LldpInfoRemoteDevicesEntry ::= SEQUENCE { lldpInfoRemoteDevicesIndex INTEGER, lldpInfoRemoteDevicesRemoteTTL Integer32, lldpInfoRemoteDevicesRxChanges INTEGER, lldpInfoRemoteDevicesLocalPort DisplayString, lldpInfoRemoteDevicesChassisSubtype INTEGER, lldpInfoRemoteDevicesChassisId DisplayString, lldpInfoRemoteDevicesPortSubtype INTEGER, lldpInfoRemoteDevicesPortId DisplayString, lldpInfoRemoteDevicesSystemName DisplayString, lldpInfoRemoteDevicesSystemDescription DisplayString, lldpInfoRemoteDevicesPortDescription DisplayString, lldpInfoRemoteDevicesSystemCapSupported DisplayString, lldpInfoRemoteDevicesSystemCapEnabled DisplayString, lldpInfoRemoteDMAC DisplayString } lldpInfoRemoteDevicesIndex OBJECT-TYPE SYNTAX INTEGER (1..256) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the row in LLDP remote devices info table." ::= { lldpInfoRemoteDevicesEntry 1 } -- lldpInfoMsapMagicNumber OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The magic number of the LLDP MSAP entry." -- ::= { lldpInfoRemoteDevicesEntry 2 } lldpInfoRemoteDevicesRemoteTTL OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The remote TTL of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 3 } lldpInfoRemoteDevicesRxChanges OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The rxChanges field of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 4 } lldpInfoRemoteDevicesLocalPort OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The local port alias of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 5 } lldpInfoRemoteDevicesChassisSubtype OBJECT-TYPE SYNTAX INTEGER { chassisComponent(1), interfaceAlias(2), portComponent(3), macAddress(4), networkAddress(5), interfaceName(6), locallyAssigned(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The chassis ID subtype of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 6 } lldpInfoRemoteDevicesChassisId OBJECT-TYPE SYNTAX DisplayString (SIZE(1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The chassis ID of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 7 } lldpInfoRemoteDevicesPortSubtype OBJECT-TYPE SYNTAX INTEGER { interfaceAlias(1), portComponent(2), macAddress(3), networkAddress(4), interfaceName(5), agentCircuitId(6), locallyAssigned(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port ID subtype of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 8 } lldpInfoRemoteDevicesPortId OBJECT-TYPE SYNTAX DisplayString (SIZE(1..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port ID of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 9 } lldpInfoRemoteDevicesSystemName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The system name of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 10 } lldpInfoRemoteDevicesSystemDescription OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The system description of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 11 } lldpInfoRemoteDevicesPortDescription OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port description of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 12 } lldpInfoRemoteDevicesSystemCapSupported OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The supported system capabilities of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 13 } lldpInfoRemoteDevicesSystemCapEnabled OBJECT-TYPE SYNTAX DisplayString (SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The enabled system capabilities of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesEntry 14 } lldpInfoRemoteDMAC OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Destination MAC address of the LLDP remote devices. Legend(possible values in DMAC column) : NB - Nearest Bridge - 01-80-C2-00-00-0E NnTB - Nearest non-TPMR Bridge - 01-80-C2-00-00-03 NCB - Nearest Customer Bridge - 01-80-C2-00-00-00" ::= { lldpInfoRemoteDevicesEntry 15 } -- -- lldpInfoRemoteDevicesManAddrTable : Management addresses of remote system -- lldpInfoRemoteDevicesManAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpInfoRemoteDevicesManAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LLDP remote devices management address Info." ::= { lldpInfo 5 } lldpInfoRemoteDevicesManAddrEntry OBJECT-TYPE SYNTAX LldpInfoRemoteDevicesManAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "LLDP remote devices management address Info." INDEX { lldpInfoRemoteDevicesIndex, lldpInfoRemoteDevicesManAddrSubtype, lldpInfoRemoteDevicesManAddr } ::= { lldpInfoRemoteDevicesManAddrTable 1 } LldpInfoRemoteDevicesManAddrEntry ::= SEQUENCE { lldpInfoRemoteDevicesManAddrSubtype INTEGER, lldpInfoRemoteDevicesManAddr DisplayString, lldpInfoRemoteDevicesManAddrIfSubtype INTEGER, lldpInfoRemoteDevicesManAddrIfId Integer32, lldpInfoRemoteDevicesManAddrOID DisplayString } lldpInfoRemoteDevicesManAddrSubtype OBJECT-TYPE SYNTAX INTEGER { other(0), ipV4(1), ipV6(2), nsap(3), hdlc(4), bbn1822(5), all802(6), e163(7), e164(8), f69(9), x121(10), ipx(11), appletalk(12), decnetIV(13), banyanVines(14), e164withNsap(15), dns(16), distinguishedname(17), asnumber(18), xtpoveripv4(19), xtpoveripv6(20), xtpnativemodextp(21), reserved(65535) } MAX-ACCESS read-only STATUS current DESCRIPTION "The management address subtype of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesManAddrEntry 1 } lldpInfoRemoteDevicesManAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The management address of the LLDP remote devices entry." ::= { lldpInfoRemoteDevicesManAddrEntry 2 } lldpInfoRemoteDevicesManAddrIfSubtype OBJECT-TYPE SYNTAX INTEGER { unknown(1), ifIndex(2), systemPortNumber(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The interface numbering subtype of the LLDP remote devices management address entry." ::= { lldpInfoRemoteDevicesManAddrEntry 3 } lldpInfoRemoteDevicesManAddrIfId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number of the LLDP remote devices management address entry." ::= { lldpInfoRemoteDevicesManAddrEntry 4 } lldpInfoRemoteDevicesManAddrOID OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The object identifier of the LLDP remote devices management address entry." ::= { lldpInfoRemoteDevicesManAddrEntry 5 } lldpClearMsap OBJECT-TYPE SYNTAX INTEGER { ok(0), clearMsap(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear LLDP remote devices information when setting clearMsap(1). When read, ok(0) is always returned." ::= { lldpInfo 6 } evbTLVInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF EvbTLVInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of ECDP TLV Info." ::= { lldpInfo 7 } evbTLVInfoEntry OBJECT-TYPE SYNTAX EvbTLVInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about EVB TLV." INDEX { evbTLVInfoEntryIndex } ::= { evbTLVInfoTable 1 } EvbTLVInfoEntry ::= SEQUENCE { evbTLVInfoEntryIndex Integer32 ,evbPort Integer32 ,evbLocalCapability OCTET STRING ,evbLocalCurrent OCTET STRING ,evbLocalRTEVal Integer32 ,evbRemoteCapability OCTET STRING ,evbRemoteCurrent OCTET STRING ,evbRemoteRTEVal Integer32 } evbTLVInfoEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the vsi info table." ::= { evbTLVInfoEntry 1 } evbPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The evb tlv port info." ::= { evbTLVInfoEntry 2 } evbLocalCapability OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The local evb tlv capabilityinfo." ::= { evbTLVInfoEntry 3 } evbLocalCurrent OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The local evb tlv current info." ::= { evbTLVInfoEntry 4 } evbLocalRTEVal OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The local evb tlv ECP RTE info." ::= { evbTLVInfoEntry 5 } evbRemoteCapability OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The remote evb tlv capability nfo." ::= { evbTLVInfoEntry 6 } evbRemoteCurrent OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The remote evb tlv cuurent info." ::= { evbTLVInfoEntry 7 } evbRemoteRTEVal OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The remote evb tlv ECP RTE info." ::= { evbTLVInfoEntry 8 } -- -- } End of LLDP Info -- -- -- { UDLD -- udldInfoPortTable OBJECT-TYPE SYNTAX SEQUENCE OF UdldInfoPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of UDLD port info." ::= { udldInfo 1 } udldInfoPortEntry OBJECT-TYPE SYNTAX UdldInfoPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row inside UDLD port info table." INDEX { udldInfoPortIndex } ::= { udldInfoPortTable 1 } UdldInfoPortEntry ::= SEQUENCE { udldInfoPortIndex PortNumber , udldInfoPortConfig INTEGER , udldInfoPortMode INTEGER , udldInfoPortLink INTEGER , udldInfoPortOperationalStatus INTEGER , udldInfoPortBidirectionalStatus INTEGER , udldInfoPortInterval INTEGER , udldInfoPortTimeout INTEGER , udldInfoPortNeighborCount INTEGER } udldInfoPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the row in UDLD port configuration table." ::= { udldInfoPortEntry 1 } udldInfoPortConfig OBJECT-TYPE SYNTAX INTEGER { enabled(1) , disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Config field of the port in UDLD port info table. Shows the administative state of the current port." ::= { udldInfoPortEntry 2 } udldInfoPortMode OBJECT-TYPE SYNTAX INTEGER { aggresive(1) , normal(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Mode field of the port in UDLD info port table. Shows the udld administrative mode for the current port." ::= { udldInfoPortEntry 3 } udldInfoPortLink OBJECT-TYPE SYNTAX INTEGER { up(1) , down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Link field of the port in UDLD info port table. Shows the state of the link associated with the port." ::= { udldInfoPortEntry 4 } udldInfoPortOperationalStatus OBJECT-TYPE SYNTAX INTEGER { init(1) , inactive(2) , linkup(3) , advertisement(4) , detection(5) , extDetection(6) , shutdown(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The OperationalStatus field of the port in UDLD info port table. Contains the udld operational state for the current port." ::= { udldInfoPortEntry 5 } udldInfoPortBidirectionalStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1) , unidirectional(2) , bidirectional(3) , loop(4) , neighborMismatch(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The BidirectionalStatus field of the port in UDLD info port table. Contains the udld bidirectional state for the current port." ::= { udldInfoPortEntry 6 } udldInfoPortInterval OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Interval field of the port in UDLD info port table. The duration, measured in seconds, of the interval during which UDLD probes are sent, after the linkup or detection phases. Its time unit is 1 second." ::= { udldInfoPortEntry 7 } udldInfoPortTimeout OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Timeout field of the port in UDLD info port table. Length of the detection phase, measured in seconds." ::= { udldInfoPortEntry 8} udldInfoPortNeighborCount OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Neighbor field of the port in UDLD info port table. Contains the number of udld neighbors for the current port." ::= { udldInfoPortEntry 9 } udldInfoNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF UdldInfoNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of UDLD port neighbor info." ::= { udldInfo 2 } udldInfoNeighborEntry OBJECT-TYPE SYNTAX UdldInfoNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row inside UDLD port info table." INDEX { udldInfoNeighborLocalPortIndex, udldInfoNeighborIndex } ::= { udldInfoNeighborTable 1 } UdldInfoNeighborEntry ::= SEQUENCE { udldInfoNeighborLocalPortIndex PortNumber , udldInfoNeighborIndex Integer32 , udldInfoNeighborExpiration INTEGER , udldInfoNeighborDeviceName DisplayString , udldInfoNeighborDeviceID DisplayString , udldInfoNeighborPortID DisplayString } udldInfoNeighborLocalPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the port for which neighbor information will be returned." ::= { udldInfoNeighborEntry 1 } udldInfoNeighborIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the target neighbor among the port neighbors." ::= { udldInfoNeighborEntry 2 } udldInfoNeighborExpiration OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Hold time for the given neighbor." ::= { udldInfoNeighborEntry 3 } udldInfoNeighborDeviceName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Device name reported by neigbor." ::= { udldInfoNeighborEntry 4 } udldInfoNeighborDeviceID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Device ID reported by neigbor." ::= { udldInfoNeighborEntry 5 } udldInfoNeighborPortID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Port ID reported by neigbor." ::= { udldInfoNeighborEntry 6 } -- -- } End of UDLD Info -- -- FDB fdbCurCfgStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF FdbCurCfgStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of FDB static entries." ::= { fdb 2 } fdbCurCfgStaticEntry OBJECT-TYPE SYNTAX FdbCurCfgStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the fdb table." INDEX { fdbCurCfgEntryIndex } ::= { fdbCurCfgStaticTable 1 } FdbCurCfgStaticEntry ::= SEQUENCE { fdbCurCfgEntryIndex Integer32, fdbCurCfgVlan Integer32, fdbCurCfgPort PortNumber, fdbCurCfgMac PhysAddress ,fdbCurCfgTrunk Integer32 ,fdbCurCfgAdminkey Integer32 } fdbCurCfgEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The fdb entry index" ::= { fdbCurCfgStaticEntry 1 } fdbCurCfgVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Add vlan for fdb entry index" ::= { fdbCurCfgStaticEntry 2 } fdbCurCfgPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address port number." ::= { fdbCurCfgStaticEntry 3 } fdbCurCfgMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Add a fdb entry." ::= { fdbCurCfgStaticEntry 4 } fdbCurCfgTrunk OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address trunk number." ::= { fdbCurCfgStaticEntry 5 } fdbCurCfgAdminkey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address LACP trunk adminkey." ::= { fdbCurCfgStaticEntry 6 } fdbNewCfgStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF FdbNewCfgStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of FDB static entries." ::= { fdb 3 } fdbNewCfgStaticEntry OBJECT-TYPE SYNTAX FdbNewCfgStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the fdb table." INDEX { fdbNewCfgEntryIndex } ::= { fdbNewCfgStaticTable 1 } FdbNewCfgStaticEntry ::= SEQUENCE { fdbNewCfgEntryIndex Integer32, fdbNewCfgAddVlan Integer32, fdbNewCfgAddPort PortNumber, fdbNewCfgAddTrunk Integer32, fdbNewCfgAddAdminkey Integer32, fdbNewCfgAddMac PhysAddress, fdbNewCfgDelStaticEntry INTEGER } fdbNewCfgEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The fdb entry index" ::= { fdbNewCfgStaticEntry 1 } fdbNewCfgAddVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Add vlan for fdb entry index" ::= { fdbNewCfgStaticEntry 2 } fdbNewCfgAddPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The MAC address port number." ::= { fdbNewCfgStaticEntry 3 } fdbNewCfgAddMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Add a fdb entry, ex:0x00 0x01 0x02 0x03 0x04 0x05" ::= { fdbNewCfgStaticEntry 4 } fdbNewCfgDelStaticEntry OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { fdbNewCfgStaticEntry 5 } fdbNewCfgAddTrunk OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The MAC address trunk number." ::= { fdbNewCfgStaticEntry 6 } fdbNewCfgAddAdminkey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The MAC address LACP trunk adminkey." ::= { fdbNewCfgStaticEntry 7 } -- Multicast FDB mcastFdbCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF McastFdbCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of multicast FDB static entries." ::= { fdb 8 } mcastFdbCurCfgEntry OBJECT-TYPE SYNTAX McastFdbCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the multicast fdb table." INDEX { mcastFdbCurCfgEntryIndex } ::= { mcastFdbCurCfgTable 1 } McastFdbCurCfgEntry ::= SEQUENCE { mcastFdbCurCfgEntryIndex Integer32, mcastFdbCurCfgVlan Integer32, mcastFdbCurCfgPorts PortNumber, mcastFdbCurCfgMac MacAddress } mcastFdbCurCfgEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast fdb entry index" ::= { mcastFdbCurCfgEntry 1 } mcastFdbCurCfgVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Add vlan for multicast fdb entry index" ::= { mcastFdbCurCfgEntry 2 } mcastFdbCurCfgPorts OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast MAC address port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the multicast MAC address. 0 - The represented port does not belong to the multicast MAC address." ::= { mcastFdbCurCfgEntry 3 } mcastFdbCurCfgMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Add a multicast fdb entry." ::= { mcastFdbCurCfgEntry 4 } mcastFdbNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF McastFdbNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of multicast FDB static entries." ::= { fdb 9 } mcastFdbNewCfgEntry OBJECT-TYPE SYNTAX McastFdbNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the multicast fdb table." INDEX { mcastFdbNewCfgEntryIndex } ::= { mcastFdbNewCfgTable 1 } McastFdbNewCfgEntry ::= SEQUENCE { mcastFdbNewCfgEntryIndex Integer32, mcastFdbNewCfgAddVlan Integer32, mcastFdbNewCfgPorts OCTET STRING, mcastFdbNewCfgAddPort PortNumber, mcastFdbNewCfgRemPort PortNumber, mcastFdbNewCfgAddMac MacAddress, mcastFdbNewCfgDelStaticEntry INTEGER } mcastFdbNewCfgEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast fdb entry index" ::= { mcastFdbNewCfgEntry 1 } mcastFdbNewCfgAddVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Add vlan for multicast fdb entry index" ::= { mcastFdbNewCfgEntry 2 } mcastFdbNewCfgPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast MAC address port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the multicast MAC address. 0 - The represented port does not belong to the multicast MAC address." ::= { mcastFdbNewCfgEntry 3 } mcastFdbNewCfgAddPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The multicast MAC address port number to be added. A '0' value is returned when read." ::= { mcastFdbNewCfgEntry 4 } mcastFdbNewCfgRemPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The multicast MAC address port number to be removed. A '0' value is returned when read." ::= { mcastFdbNewCfgEntry 5 } mcastFdbNewCfgAddMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Add a multicast fdb entry, ex:0x00 0x01 0x02 0x03 0x04 0x05" ::= { mcastFdbNewCfgEntry 6 } mcastFdbNewCfgDelStaticEntry OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { mcastFdbNewCfgEntry 7 } --dot1x dot1xCurStatus OBJECT-TYPE SYNTAX INTEGER { enable(0), disable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " Dot1x status " ::= { dot1x 1 } dot1xNewStatus OBJECT-TYPE SYNTAX INTEGER { enable(0), disable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION " Dot1x status " ::= { dot1x 2 } dot1xCurCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1xCurCfgPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of 8021x configuration in the Current_config." ::= { dot1x 3 } dot1xNewCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1xNewCfgPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of 8021x configuration in the new_config." ::= { dot1x 4 } dot1xCurCfgPortEntry OBJECT-TYPE SYNTAX Dot1xCurCfgPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about 8021x Port Config" INDEX { dot1xCurCfgPortIndex } ::= { dot1xCurCfgPortTable 1 } Dot1xCurCfgPortEntry ::= SEQUENCE { dot1xCurCfgPortIndex PortNumber, dot1xCurCfgPortMode INTEGER, dot1xCurCfgPortQtPeriod INTEGER, dot1xCurCfgPortTxPeriod INTEGER, dot1xCurCfgPortSupTmout INTEGER, dot1xCurCfgPortSrvTmout INTEGER, dot1xCurCfgPortMaxRq INTEGER, dot1xCurCfgPortRaPeriod INTEGER, dot1xCurCfgPortReAuth INTEGER , dot1xCurCfgPortVlanAssign INTEGER } dot1xCurCfgPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The 8021x Port number for which the table is related." ::= { dot1xCurCfgPortEntry 1} dot1xCurCfgPortMode OBJECT-TYPE SYNTAX INTEGER { forceUnauth(0), auto(1), forceAuth(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " Port authenticaton mode forceUnauth(0), auto(1), forceAuth(2) " ::= { dot1xCurCfgPortEntry 2 } dot1xCurCfgPortQtPeriod OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Quiet period (0-65535) " ::= { dot1xCurCfgPortEntry 3 } dot1xCurCfgPortTxPeriod OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION " Tx Period " ::= { dot1xCurCfgPortEntry 4 } dot1xCurCfgPortSupTmout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION " Supplicant timeout (1..65535) " ::= { dot1xCurCfgPortEntry 5 } dot1xCurCfgPortSrvTmout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION " Server timeout (1..65535) " ::= { dot1xCurCfgPortEntry 6 } dot1xCurCfgPortMaxRq OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION " Maximum numer of requests (1..10) " ::= { dot1xCurCfgPortEntry 7 } dot1xCurCfgPortRaPeriod OBJECT-TYPE SYNTAX INTEGER (0..604800) MAX-ACCESS read-only STATUS current DESCRIPTION " Reautentication period (0..604800) " ::= { dot1xCurCfgPortEntry 8 } dot1xCurCfgPortReAuth OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " ReAuthentication state off(0), on(1) " ::= { dot1xCurCfgPortEntry 9 } dot1xCurCfgPortVlanAssign OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " Vlan assignment state off(0), on(1) " ::= { dot1xCurCfgPortEntry 10 } dot1xNewCfgPortEntry OBJECT-TYPE SYNTAX Dot1xNewCfgPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about 8021x Port Config" INDEX { dot1xNewCfgPortIndex } ::= { dot1xNewCfgPortTable 1 } Dot1xNewCfgPortEntry ::= SEQUENCE { dot1xNewCfgPortIndex PortNumber, dot1xNewCfgPortMode INTEGER, dot1xNewCfgPortQtPeriod INTEGER, dot1xNewCfgPortTxPeriod INTEGER, dot1xNewCfgPortSupTmout INTEGER, dot1xNewCfgPortSrvTmout INTEGER, dot1xNewCfgPortMaxRq INTEGER, dot1xNewCfgPortRaPeriod INTEGER, dot1xNewCfgPortReAuth INTEGER , dot1xNewCfgPortDefault INTEGER , dot1xNewCfgPortApplyGlobal INTEGER , dot1xNewCfgPortVlanAssign INTEGER } dot1xNewCfgPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The 8021x Port number for which the table is related." ::= { dot1xNewCfgPortEntry 1} dot1xNewCfgPortMode OBJECT-TYPE SYNTAX INTEGER { forceUnauth(0), auto(1), forceAuth(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " Port authentication mode forceUnauth(0), auto(1), forceAuth(2) " ::= { dot1xNewCfgPortEntry 2 } dot1xNewCfgPortQtPeriod OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION " Quiet period (0..65535) " ::= { dot1xNewCfgPortEntry 3 } dot1xNewCfgPortTxPeriod OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION " Tx Period (1..65535) " ::= { dot1xNewCfgPortEntry 4 } dot1xNewCfgPortSupTmout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION " Supplicant Timeout (1..65535) " ::= { dot1xNewCfgPortEntry 5 } dot1xNewCfgPortSrvTmout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION " Server Timeout (1..65535) " ::= { dot1xNewCfgPortEntry 6 } dot1xNewCfgPortMaxRq OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION " Maximum number of requests (1..10) " ::= { dot1xNewCfgPortEntry 7 } dot1xNewCfgPortRaPeriod OBJECT-TYPE SYNTAX INTEGER (1..604800) MAX-ACCESS read-create STATUS current DESCRIPTION " Reauthentication period (1..604800) " ::= { dot1xNewCfgPortEntry 8 } dot1xNewCfgPortReAuth OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-create STATUS current DESCRIPTION " Reauthentication state off(0), on(1) " ::= { dot1xNewCfgPortEntry 9 } dot1xNewCfgPortDefault OBJECT-TYPE SYNTAX INTEGER { other(0), apply(1) } MAX-ACCESS read-create STATUS current DESCRIPTION " Port default settings " ::= { dot1xNewCfgPortEntry 10 } dot1xNewCfgPortApplyGlobal OBJECT-TYPE SYNTAX INTEGER { other(0), apply(1) } MAX-ACCESS read-create STATUS current DESCRIPTION " Apply Global config " ::= { dot1xNewCfgPortEntry 11 } dot1xNewCfgPortVlanAssign OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/Disable the assignment of vlan from radius server when the port is successfully autheticated. Vlan assignment state off(0), on(1) " ::= { dot1xNewCfgPortEntry 12 } dot1xCurCfgGuestVlanNumber OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION " 8021.x Guest VLAN number" ::= { dot1xCurCfgGuestVlan 1 } dot1xCurCfgGuestVlanStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " 8021.x Guest VLAN status enabled(1), disabled(2)" ::= { dot1xCurCfgGuestVlan 2 } dot1xCurCfgGlobalMode OBJECT-TYPE SYNTAX INTEGER { forceUnauth(0), auto(1), forceAuth(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " Autehtication Mode forceUnauth(0), auto(1), forceAuth(2) " ::= { dot1xCurCfgGlobalTable 3 } dot1xCurCfgGlobalQtPeriod OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION " Quiet period (0..65535) " ::= { dot1xCurCfgGlobalTable 4 } dot1xCurCfgGlobalTxPeriod OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION " Tx period (1..65535) " ::= { dot1xCurCfgGlobalTable 5 } dot1xCurCfgGlobalSupTmout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION " Supplicant timeout (1..65535) " ::= { dot1xCurCfgGlobalTable 6 } dot1xCurCfgGlobalSrvTmout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION " Server timeout (1..65535) " ::= { dot1xCurCfgGlobalTable 7 } dot1xCurCfgGlobalMaxRq OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION " Maximum number of requests (1..10) " ::= { dot1xCurCfgGlobalTable 8 } dot1xCurCfgGlobalRaPeriod OBJECT-TYPE SYNTAX INTEGER (0..604800) MAX-ACCESS read-only STATUS current DESCRIPTION " Reauthentication period (0..604800) " ::= { dot1xCurCfgGlobalTable 9 } dot1xCurCfgGlobalReAuth OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " " ::= { dot1xCurCfgGlobalTable 10 } dot1xCurCfgGlobalVlanAssign OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Vlan assignment status" ::= { dot1xCurCfgGlobalTable 12 } dot1xNewCfgGuestVlanNumber OBJECT-TYPE SYNTAX INTEGER (0..4094) MAX-ACCESS read-write STATUS current DESCRIPTION " 8021.x Guest VLAN number " ::= { dot1xNewCfgGuestVlan 1 } dot1xNewCfgGuestVlanStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION " 8021.x Guest VLAN status enabled(1), disabled(2)" ::= { dot1xNewCfgGuestVlan 2 } dot1xNewCfgGlobalMode OBJECT-TYPE SYNTAX INTEGER { forceUnauth(0), auto(1), forceAuth(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " Authentication Mode " ::= { dot1xNewCfgGlobalTable 3 } dot1xNewCfgGlobalQtPeriod OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION " Quiet Period (0..65535) " ::= { dot1xNewCfgGlobalTable 4 } dot1xNewCfgGlobalTxPeriod OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION " Tx Period (1..65535) " ::= { dot1xNewCfgGlobalTable 5 } dot1xNewCfgGlobalSupTmout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION " Supplicand timeout (1..65535) " ::= { dot1xNewCfgGlobalTable 6 } dot1xNewCfgGlobalSrvTmout OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION " Server timeout (1..65535) " ::= { dot1xNewCfgGlobalTable 7 } dot1xNewCfgGlobalMaxRq OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION " Maximum number of requests (1..10) " ::= { dot1xNewCfgGlobalTable 8 } dot1xNewCfgGlobalRaPeriod OBJECT-TYPE SYNTAX INTEGER (1..604800) MAX-ACCESS read-create STATUS current DESCRIPTION " Reauthentication period (1..604800) " ::= { dot1xNewCfgGlobalTable 9 } dot1xNewCfgGlobalReAuth OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-create STATUS current DESCRIPTION " Reauthentication status " ::= { dot1xNewCfgGlobalTable 10 } dot1xNewCfgGlobalDefault OBJECT-TYPE SYNTAX INTEGER { other(0), apply(1) } MAX-ACCESS read-create STATUS current DESCRIPTION " Restore default 802.1x configuration " ::= { dot1xNewCfgGlobalTable 11 } dot1xNewCfgGlobalVlanAssign OBJECT-TYPE SYNTAX INTEGER { off(0), on(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/Disable the assignment of vlan from radius server when the port is successfully autheticated." ::= { dot1xNewCfgGlobalTable 12 } dot1xInfoPortTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1xInfoPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of 8021x configuration in the Current_config." ::= { dot1xInfo 1 } dot1xInfoPortEntry OBJECT-TYPE SYNTAX Dot1xInfoPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about 8021x Port Config" INDEX { dot1xInfoPortIndex } ::= { dot1xInfoPortTable 1 } Dot1xInfoPortEntry ::= SEQUENCE { dot1xInfoPortIndex PortNumber, dot1xInfoPortAuthMode INTEGER, dot1xInfoPortAuthStatus INTEGER, dot1xInfoPortAuthPAEState INTEGER, dot1xInfoPortBackAuthState INTEGER , dot1xInfoPortAssignedVlan INTEGER } dot1xInfoPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The 8021x Port number for which the table is related." ::= { dot1xInfoPortEntry 1} dot1xInfoPortAuthMode OBJECT-TYPE SYNTAX INTEGER { forceUnauth(0), auto(1), forceAuth(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " Authentication mode " ::= { dot1xInfoPortEntry 2 } dot1xInfoPortAuthStatus OBJECT-TYPE SYNTAX INTEGER { authorized(0), unauthorized(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " Authentication status " ::= { dot1xInfoPortEntry 3 } dot1xInfoPortAuthPAEState OBJECT-TYPE SYNTAX INTEGER { initialize(0), disconnected(1), connecting(2), authenticating(3), authenticated(4), aborting(5), held(6), forceauth(7), forceunauth(8) } MAX-ACCESS read-only STATUS current DESCRIPTION " Authenticator PAE State " ::= { dot1xInfoPortEntry 5 } dot1xInfoPortBackAuthState OBJECT-TYPE SYNTAX INTEGER { request(0), response(1), success(2), fail(3), timeout(4), idle(5), initialize(6) } MAX-ACCESS read-only STATUS current DESCRIPTION " Backend authenticator PAE state " ::= { dot1xInfoPortEntry 6 } dot1xInfoPortAssignedVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Vlan assigned from radius server.Value of 0 indicates , no vlan assigned via Radius" ::= { dot1xInfoPortEntry 7 } dot1xSystemCapability OBJECT-TYPE SYNTAX INTEGER { authenticator(0), supplicant(1), authenticatorAndSupplicant(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION " System capability " ::= { dot1xSystemInfo 1 } dot1xSystemStatus OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " System status " ::= { dot1xSystemInfo 2 } dot1xSystemProtoVersion OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION " Protocol version " ::= { dot1xSystemInfo 3 } oamInfoPortTable OBJECT-TYPE SYNTAX SEQUENCE OF OAMInfoPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OAM port information." ::= { oamInfo 1 } oamInfoPortEntry OBJECT-TYPE SYNTAX OAMInfoPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about OAM Port" INDEX { oamInfoPortIndex } ::= { oamInfoPortTable 1 } OAMInfoPortEntry ::= SEQUENCE { oamInfoPortIndex PortNumber, oamInfoPortLocalState INTEGER, oamInfoPortLocalMode INTEGER, oamInfoPortLocalLinkStatus INTEGER, oamInfoPortLocalStable INTEGER, oamInfoPortLocalSatisfied INTEGER, oamInfoPortLocalEvaluating INTEGER, oamInfoPortRemoteMode INTEGER, oamInfoPortRemoteMAC PhysAddress, oamInfoPortRemoteStable INTEGER, oamInfoPortRemoteStateValid INTEGER, oamInfoPortRemoteEvaluating INTEGER } oamInfoPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The OAM Port number for which the table is related." ::= { oamInfoPortEntry 1} oamInfoPortLocalState OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " OAM local port state" ::= { oamInfoPortEntry 2 } oamInfoPortLocalMode OBJECT-TYPE SYNTAX INTEGER { active(0), passive(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " OAM local port mode" ::= { oamInfoPortEntry 3 } oamInfoPortLocalLinkStatus OBJECT-TYPE SYNTAX INTEGER { ok(0), fail(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " OAM local port link status" ::= { oamInfoPortEntry 4 } oamInfoPortLocalStable OBJECT-TYPE SYNTAX INTEGER { true(0), false(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " OAM local port stable" ::= { oamInfoPortEntry 5 } oamInfoPortLocalSatisfied OBJECT-TYPE SYNTAX INTEGER { true(0), false(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " OAM local port satisfied" ::= { oamInfoPortEntry 6 } oamInfoPortLocalEvaluating OBJECT-TYPE SYNTAX INTEGER { true(0), false(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " OAM local port evaluating" ::= { oamInfoPortEntry 7 } oamInfoPortRemoteMode OBJECT-TYPE SYNTAX INTEGER { active(0), passive(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " OAM remote port mode" ::= { oamInfoPortEntry 8 } oamInfoPortRemoteMAC OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION " OAM remote port MAC address" ::= { oamInfoPortEntry 9 } oamInfoPortRemoteStable OBJECT-TYPE SYNTAX INTEGER { true(0), false(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " OAM remote port stable" ::= { oamInfoPortEntry 10 } oamInfoPortRemoteStateValid OBJECT-TYPE SYNTAX INTEGER { true(0), false(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " OAM remote port state valid" ::= { oamInfoPortEntry 11 } oamInfoPortRemoteEvaluating OBJECT-TYPE SYNTAX INTEGER { true(0), false(1) } MAX-ACCESS read-only STATUS current DESCRIPTION " OAM remote port evaluating" ::= { oamInfoPortEntry 12 } -- -- OAM Stats -- oamStatsPortTable OBJECT-TYPE SYNTAX SEQUENCE OF OAMStatsPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OAM port statistics." ::= { oamStats 1 } oamStatsPortEntry OBJECT-TYPE SYNTAX OAMStatsPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics about OAM Port" INDEX { oamStatsPortIndex } ::= { oamStatsPortTable 1 } OAMStatsPortEntry ::= SEQUENCE { oamStatsPortIndex PortNumber, oamStatsPortInfoTx INTEGER, oamStatsPortInfoRx INTEGER, oamStatsPortUnsupTx INTEGER, oamStatsPortUnsupRx INTEGER, oamStatsPortLocalLinkFaults INTEGER, oamStatsPortLocalCriticalEvents INTEGER, oamStatsPortLocalDyingGasps INTEGER, oamStatsPortRemoteLinkFaults INTEGER, oamStatsPortRemoteCriticalEvents INTEGER, oamStatsPortRemoteDyingGasps INTEGER } oamStatsPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The OAM Port number for which the table is related." ::= { oamStatsPortEntry 1} oamStatsPortInfoTx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transmitted OAM information packets" ::= { oamStatsPortEntry 2} oamStatsPortInfoRx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of received OAM information packets" ::= { oamStatsPortEntry 3} oamStatsPortUnsupTx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of transmitted OAM unsupported packets" ::= { oamStatsPortEntry 4} oamStatsPortUnsupRx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of received OAM unsupported packets" ::= { oamStatsPortEntry 5} oamStatsPortLocalLinkFaults OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of local OAM link fault packets" ::= { oamStatsPortEntry 6} oamStatsPortLocalCriticalEvents OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of local OAM critical event packets" ::= { oamStatsPortEntry 7} oamStatsPortLocalDyingGasps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of local OAM dying gasp packets" ::= { oamStatsPortEntry 8} oamStatsPortRemoteLinkFaults OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of remote OAM link fault packets" ::= { oamStatsPortEntry 9} oamStatsPortRemoteCriticalEvents OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of remote OAM critical event packets" ::= { oamStatsPortEntry 10} oamStatsPortRemoteDyingGasps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of remote OAM dying gasp packets" ::= { oamStatsPortEntry 11} -- Trunk Group Information trunkGroupInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF TrunkGroupInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of trunk group information." ::= { trunkGroupInfo 1 } trunkGroupInfoTableEntry OBJECT-TYPE SYNTAX TrunkGroupInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in trunk group information table." INDEX { trunkGroupInfoIndex } ::= { trunkGroupInfoTable 1 } TrunkGroupInfoTableEntry ::= SEQUENCE { trunkGroupInfoIndex Integer32, trunkGroupInfoState INTEGER, trunkGroupInfoProtocol INTEGER, trunkGroupInfoPorts OCTET STRING } trunkGroupInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the trunk group." ::= { trunkGroupInfoTableEntry 1 } trunkGroupInfoState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Trunk group state." ::= { trunkGroupInfoTableEntry 2 } trunkGroupInfoPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the trunk group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the trunk group 0 - The represented port does not belong to the trunk group" ::= { trunkGroupInfoTableEntry 3 } trunkGroupInfoProtocol OBJECT-TYPE SYNTAX INTEGER { static(1), lacp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Trunk group protocol Static - static trunk group Lacp - dynamic trunk group" ::= { trunkGroupInfoTableEntry 4 } trunkGroupInfoPortTable OBJECT-TYPE SYNTAX SEQUENCE OF TrunkGroupInfoPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Trunk Group Info." ::= {trunkGroupInfo 2 } trunkGroupInfoPortTableEntry OBJECT-TYPE SYNTAX TrunkGroupInfoPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Trunk Info table." INDEX { trunkGroupInfoPortTrunkId, trunkGroupInfoPortPortId } ::= { trunkGroupInfoPortTable 1 } TrunkGroupInfoPortTableEntry ::= SEQUENCE { trunkGroupInfoPortTrunkId Integer32, trunkGroupInfoPortPortId PortNumber, trunkGroupInfoPortStatus INTEGER } trunkGroupInfoPortTrunkId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Trunk identifier." ::= { trunkGroupInfoPortTableEntry 1 } trunkGroupInfoPortPortId OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The Port identifier." ::= { trunkGroupInfoPortTableEntry 2 } trunkGroupInfoPortStatus OBJECT-TYPE SYNTAX INTEGER{ down(0), blocking(1), forwarding(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Status." ::= { trunkGroupInfoPortTableEntry 3 } -- LACP Statistics lacpStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF LacpStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LACP Stats." ::= {lacpStats 1} lacpStatsTableEntry OBJECT-TYPE SYNTAX LacpStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Lacp status info." INDEX { lacpStatsIndex } ::= { lacpStatsTable 1 } LacpStatsTableEntry ::= SEQUENCE { lacpStatsIndex PortNumber, lacpdusRx Integer32, markerpdusRx Integer32, markerresponsepdusRx Integer32, unknownRx Integer32, illegalRx Integer32, lacpdusTx Integer32, markerpdusTx Integer32, markerresponsepdusTx Integer32 ,lacpClearStats INTEGER } lacpStatsIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Index" ::= {lacpStatsTableEntry 1} lacpdusRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Valid LACPDUs received" ::= {lacpStatsTableEntry 2} markerpdusRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Valid Marker PDUs received" ::= {lacpStatsTableEntry 3} markerresponsepdusRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Valid Marker Rsp PDUs received" ::= {lacpStatsTableEntry 4} unknownRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Unknown version/TLV type" ::= {lacpStatsTableEntry 5} illegalRx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Illegal subtype received" ::= {lacpStatsTableEntry 6} lacpdusTx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACPDUs transmitted" ::= {lacpStatsTableEntry 7} markerpdusTx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Market PDUs transmitted" ::= {lacpStatsTableEntry 8} markerresponsepdusTx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Marker Rsp PDUs transmitted " ::= {lacpStatsTableEntry 9} lacpClearStats OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(2) results in clearing the LACP statistics." ::= { lacpStatsTableEntry 10 } -- FDB Statistics fdbStatsCurrent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current number of entries in the Forwarding Database." ::= { fdbStats 3 } fdbStatsHiwat OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Highest number of entries recorded at any given time in the Forwarding Database." ::= { fdbStats 4 } fdbStatsClear OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear FDB statistics" ::= { fdbStats 11 } -- STP Statistics stgStatsPortTable OBJECT-TYPE SYNTAX SEQUENCE OF StgStatsPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Spanning Tree Group port statistics." ::= { stpStats 1 } stgStatsPortTableEntry OBJECT-TYPE SYNTAX StgStatsPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics about port of a particular Spanning Tree Group." INDEX { stgStatsStpIndex, stgStatsPortIndex } ::= { stgStatsPortTable 1 } StgStatsPortTableEntry ::= SEQUENCE { stgStatsStpIndex Integer32, stgStatsPortIndex PortNumber, stgStatsPortRcvCfgBpdus Counter32, stgStatsPortRcvTcnBpdus Counter32, stgStatsPortXmtCfgBpdus Counter32, stgStatsPortXmtTcnBpdus Counter32 } stgStatsStpIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular Spanning Tree Group." ::= { stgStatsPortTableEntry 1 } stgStatsPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier of a particular Spanning Tree Group." ::= { stgStatsPortTableEntry 2 } stgStatsPortRcvCfgBpdus OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Configuration BPDU's received on this port." ::= { stgStatsPortTableEntry 3 } stgStatsPortRcvTcnBpdus OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of TCN BPDU's received on this port." ::= { stgStatsPortTableEntry 4 } stgStatsPortXmtCfgBpdus OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Configuration BPDU's trasmitted from the port." ::= { stgStatsPortTableEntry 5 } stgStatsPortXmtTcnBpdus OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of TCN BPDU's trasmitted from the port." ::= { stgStatsPortTableEntry 6 } fdbClear OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the entire master FDB." ::= { fdbInfo 1 } -- FDB table fdbTable OBJECT-TYPE SYNTAX SEQUENCE OF FdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of FDB entries." ::= { fdbInfo 2 } fdbEntry OBJECT-TYPE SYNTAX FdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the FDB table" INDEX { fdbMacAddr } ::= { fdbTable 1 } FdbEntry ::= SEQUENCE { fdbMacAddr MacAddress, fdbVlan Integer32, fdbSrcPort PortNumber, fdbSrcTrunk Integer32, fdbState INTEGER ,fdbStatus Integer32 } fdbMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address for the FDB entry." ::= { fdbEntry 1 } fdbVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID for the FDB entry." ::= { fdbEntry 2 } fdbSrcPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address." ::= { fdbEntry 3 } fdbState OBJECT-TYPE SYNTAX INTEGER { unknown(1), forward(2), trunk(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the FDB entry. The meanings of the values are : unknown(1) : the MAC address has not yet been learned by the switch but has only been seen as a destination address forward(2) : the MAC address has been learned by the switch trunk(3) : frames with this MAC address are forwarded to trunk group" ::= { fdbEntry 4 } fdbSrcTrunk OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Either the value '0', or the trunk number of the trunk on which a frame having a source address equal to the value of the corresponding instance has been seen. A value of '0' indicates that the source address is not associated with a trunk." ::= { fdbEntry 7 } fdbStatus OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "'1' if it is permanent '0' if it is not permanent" ::= { fdbEntry 8 } -- Multicast FDB table mcastFdbTable OBJECT-TYPE SYNTAX SEQUENCE OF McastFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of static multicast FDB entries." ::= { fdbInfo 3 } mcastFdbEntry OBJECT-TYPE SYNTAX McastFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static multicast FDB table" INDEX { mcastFdbEntryIndex } ::= { mcastFdbTable 1 } McastFdbEntry ::= SEQUENCE { mcastFdbEntryIndex Integer32, mcastFdbMacAddr MacAddress, mcastFdbVlan Integer32, mcastFdbSrcPorts PortNumber } mcastFdbEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The static multicast fdb entry index" ::= { mcastFdbEntry 1 } mcastFdbMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The static multicast MAC address for the FDB entry." ::= { mcastFdbEntry 2 } mcastFdbVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID for the FDB entry." ::= { mcastFdbEntry 3 } mcastFdbSrcPorts OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast MAC address port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the multicast MAC address. 0 - The represented port does not belong to the multicast MAC address." ::= { mcastFdbEntry 4 } -- STP Information stpInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF StpInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Spanning Tree Group information." ::= { stpInfo 1 } stpInfoTableEntry OBJECT-TYPE SYNTAX StpInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Spanning Tree Group." INDEX { stpInfoIndex } ::= { stpInfoTable 1 } StpInfoTableEntry ::= SEQUENCE { stpInfoIndex Integer32, stpInfoTimeSinceTopChange TimeTicks, stpInfoTopChanges Counter32, stpInfoDesignatedRoot BridgeId, stpInfoRootCost Integer32, stpInfoRootPort PortNumber, stpInfoMaxAge Integer32, stpInfoHelloTime Integer32, stpInfoForwardDelay Integer32, stpInfoHoldTime Integer32 } stpInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular Spanning Tree Group. This is also index to the entLogicalTable of Entity MIB." ::= { stpInfoTableEntry 1 } stpInfoTimeSinceTopChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity." ::= { stpInfoTableEntry 2 } stpInfoTopChanges OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of topology changes detected by this bridge since the management entity was last reset or initialized." ::= { stpInfoTableEntry 3 } stpInfoDesignatedRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node." ::= { stpInfoTableEntry 4 } stpInfoRootCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the path to the root as seen from this bridge." ::= { stpInfoTableEntry 5 } stpInfoRootPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the port which offers the lowest cost path from this bridge to the root bridge." ::= { stpInfoTableEntry 6 } stpInfoMaxAge OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using." ::= { stpInfoTableEntry 7 } stpInfoHelloTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using." ::= { stpInfoTableEntry 8 } stpInfoForwardDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database." ::= { stpInfoTableEntry 9 } stpInfoHoldTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second." ::= { stpInfoTableEntry 10 } stpInfoPortTable OBJECT-TYPE SYNTAX SEQUENCE OF StpInfoPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Spanning Tree Group port information." ::= { stpInfo 2 } stpInfoPortTableEntry OBJECT-TYPE SYNTAX StpInfoPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about port configuration for a particular Spanning Tree Group." INDEX { stpInfoPortStpIndex, stpInfoPortIndex } ::= { stpInfoPortTable 1 } StpInfoPortTableEntry ::= SEQUENCE { stpInfoPortStpIndex Integer32, stpInfoPortIndex PortNumber, stpInfoPortState INTEGER, stpInfoPortDesignatedRoot BridgeId, stpInfoPortDesignatedCost Integer32, stpInfoPortDesignatedBridge BridgeId, stpInfoPortDesignatedPort OCTET STRING, stpInfoPortForwardTransitions Counter32, stpInfoPortRole INTEGER, stpInfoPortLinkType INTEGER, stpInfoPortEdge INTEGER, stpInfoPortExtGuard INTEGER, stpInfoPortPathCost Integer32, stpInfoPortPriority Integer32 } stpInfoPortStpIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular Spanning Tree Group." ::= { stpInfoPortTableEntry 1 } stpInfoPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier of a particular Spanning Tree Group." ::= { stpInfoPortTableEntry 2 } stpInfoPortState OBJECT-TYPE SYNTAX INTEGER { disabled(1), blocking(2), listening(3), learning(4), forwarding(5), discarding(7), broken(6), na(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled, this object will have a value of disabled(1). If port is not controlled by STP, this object will have a value of na (8)." ::= { stpInfoPortTableEntry 3 } stpInfoPortDesignatedRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached." ::= { stpInfoPortTableEntry 4 } stpInfoPortDesignatedCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs." ::= { stpInfoPortTableEntry 5 } stpInfoPortDesignatedBridge OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment." ::= { stpInfoPortTableEntry 6 } stpInfoPortDesignatedPort OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Identifier of the port on the Designated Bridge for this port's segment." ::= { stpInfoPortTableEntry 7 } stpInfoPortForwardTransitions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this port has transitioned from the Learning state to the Forwarding state." ::= { stpInfoPortTableEntry 8 } stpInfoPortPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The path cost of the port." ::= { stpInfoPortTableEntry 9 } stpInfoPortRole OBJECT-TYPE SYNTAX INTEGER { disabled(1), alternate(2), backup(3), root(4), designated(5), master(6), unknown(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port role. Returns unknown(7) when MSTP/RSTP is not enabled, otherwise returns appropriate port role." ::= { stpInfoPortTableEntry 10 } stpInfoPortLinkType OBJECT-TYPE SYNTAX INTEGER { p2p(1), shared(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The point-to-point status of the LAN segment attached to this port. A value of p2p (1) indicates that this port is being treated as if it is connected to a point-to-point link. A value of shared(2) indicates that this port is being treated as having a shared media connection." ::= { stpInfoPortTableEntry 11 } stpInfoPortEdge OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port is an edge port or not. Returns disabled(2) when the port is not an edge port and returns enabled(1) when it is an edge port." ::= { stpInfoPortTableEntry 12 } stpInfoPortExtGuard OBJECT-TYPE SYNTAX INTEGER { loop-inc(1), root-inc(2), normal(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current STP guard state. Not include BPDU Guard." ::= { stpInfoPortTableEntry 13 } stpInfoPortPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value." ::= { stpInfoPortTableEntry 14 } -- LACP information lacpInfoAggrTable OBJECT-TYPE SYNTAX SEQUENCE OF LacpInfoAggrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LACP aggregator information." ::= { lacpInfo 1 } lacpInfoAggrTableEntry OBJECT-TYPE SYNTAX LacpInfoAggrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a LACP aggregator." INDEX { lacpInfoAggrIndex } ::= { lacpInfoAggrTable 1 } LacpInfoAggrTableEntry ::= SEQUENCE { lacpInfoAggrIndex PortNumber, lacpInfoAggrId Integer32, lacpInfoAggrMac DisplayString, lacpInfoAggrActSysPrio Integer32, lacpInfoAggrActSysId DisplayString, lacpInfoAggrIndivState INTEGER, lacpInfoAggrActAdminKey Integer32, lacpInfoAggrActOperKey Integer32, lacpInfoAggrPartSysPrio Integer32, lacpInfoAggrPartSysId DisplayString, lacpInfoAggrPartOperKey Integer32, lacpInfoAggrReadyState INTEGER, lacpInfoAggrNumPorts Integer32 ,lacpInfoAggrMinLinks Integer32 } lacpInfoAggrIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The aggregator identifier." ::= { lacpInfoAggrTableEntry 1 } lacpInfoAggrId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator ID" ::= { lacpInfoAggrTableEntry 2 } lacpInfoAggrMac OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator MAC address" ::= { lacpInfoAggrTableEntry 3 } lacpInfoAggrActSysPrio OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator actor system priority" ::= { lacpInfoAggrTableEntry 4 } lacpInfoAggrActSysId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator actor system ID" ::= { lacpInfoAggrTableEntry 5 } lacpInfoAggrIndivState OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator individual state" ::= { lacpInfoAggrTableEntry 6 } lacpInfoAggrActAdminKey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator actor admin key" ::= { lacpInfoAggrTableEntry 7 } lacpInfoAggrActOperKey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator actor oper key" ::= { lacpInfoAggrTableEntry 8 } lacpInfoAggrPartSysPrio OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator partner system priority" ::= { lacpInfoAggrTableEntry 9 } lacpInfoAggrPartSysId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator partner system ID" ::= { lacpInfoAggrTableEntry 10 } lacpInfoAggrPartOperKey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator partner oper key" ::= { lacpInfoAggrTableEntry 11 } lacpInfoAggrReadyState OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "LACP aggregator ready state" ::= { lacpInfoAggrTableEntry 12 } lacpInfoAggrNumPorts OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of ports in aggregator" ::= { lacpInfoAggrTableEntry 13 } lacpInfoAggrMinLinks OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Min Links of ports in aggregator" ::= { lacpInfoAggrTableEntry 15 } lacpInfoPort OBJECT IDENTIFIER ::= { lacpInfo 2 } lacpInfoPortGeneralTable OBJECT-TYPE SYNTAX SEQUENCE OF LacpInfoPortGeneralTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LACP port general information." ::= { lacpInfoPort 1 } lacpInfoPortGeneralTableEntry OBJECT-TYPE SYNTAX LacpInfoPortGeneralTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "General information about a LACP port." INDEX { lacpInfoPortGeneralIndex } ::= { lacpInfoPortGeneralTable 1 } LacpInfoPortGeneralTableEntry ::= SEQUENCE { lacpInfoPortGeneralIndex PortNumber, lacpInfoPortLacpEna INTEGER, lacpInfoPortAdminEna INTEGER, lacpInfoPortActSysId DisplayString, lacpInfoPortActSysPrio Integer32, lacpInfoPortActAdminKey Integer32, lacpInfoPortActOperKey Integer32, lacpInfoPortActPortNum Integer32, lacpInfoPortActPortPrio Integer32, lacpInfoPortIndivState INTEGER, lacpInfoSelAggrId Integer32, lacpInfoAttAggrId Integer32, lacpInfoPortReadyN INTEGER, lacpInfoPortNtt INTEGER, lacpInfoPortSelected INTEGER, lacpInfoPortMoved INTEGER, lacpInfoCollDetState INTEGER, lacpInfoPortRxState DisplayString, lacpInfoPortMuxState DisplayString, lacpInfoPortPerState DisplayString, lacpInfoPortPerTraTimer Integer32, lacpInfoPortCurWhileTimer Integer32, lacpInfoPortOperState INTEGER } lacpInfoPortGeneralIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier." ::= { lacpInfoPortGeneralTableEntry 1 } lacpInfoPortLacpEna OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "LACP enabled on port" ::= { lacpInfoPortGeneralTableEntry 2 } lacpInfoPortAdminEna OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port admin enabled" ::= { lacpInfoPortGeneralTableEntry 3 } lacpInfoPortActSysId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port actor system ID" ::= { lacpInfoPortGeneralTableEntry 4 } lacpInfoPortActSysPrio OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port actor system priority" ::= { lacpInfoPortGeneralTableEntry 5 } lacpInfoPortActAdminKey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port actor admin key" ::= { lacpInfoPortGeneralTableEntry 6 } lacpInfoPortActOperKey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port actor oper key" ::= { lacpInfoPortGeneralTableEntry 7 } lacpInfoPortActPortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port number" ::= { lacpInfoPortGeneralTableEntry 8 } lacpInfoPortActPortPrio OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port priority" ::= { lacpInfoPortGeneralTableEntry 9 } lacpInfoPortIndivState OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port individual state" ::= { lacpInfoPortGeneralTableEntry 10 } lacpInfoSelAggrId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port selected aggregator ID" ::= { lacpInfoPortGeneralTableEntry 11 } lacpInfoAttAggrId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port attached aggregator ID" ::= { lacpInfoPortGeneralTableEntry 12 } lacpInfoPortReadyN OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "True value for Ready_N flag indicates that the wait while timer has expired and it is waiting to attach to an aggregator. There is one Ready_N value for each port." ::= { lacpInfoPortGeneralTableEntry 13 } lacpInfoPortNtt OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Need to transmit flag. True indicates that there is new protocol information that should be transmitted on the link." ::= { lacpInfoPortGeneralTableEntry 14 } lacpInfoPortSelected OBJECT-TYPE SYNTAX INTEGER { selected(1), unselected(2), standby(3) , suspended(4) , individual(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Selected flag value indicates that the selection logic has selected an appropriate Aggregator. A value of unselected indicates that no aggregator is currently selected. A value of standby indicates that although the selection logic has selected an appropriate Aggregator, aggregation restrictions currently prevent the port from being enabled as part of the aggregation, and so the port is being held in standby condition. A value of suspended indicates that the port in a LACP port-channel cannot be aggregated due to, for example, incompatible LACP system/port attributes of the remote endpoints. A value of suspended indicates that the port in a LACP port-channel cannot be aggregated due to, for example, not receiveing LACPDU. A value of individual indicates that the port works as a normal link-up port due to not receiving LACPDU. " ::= { lacpInfoPortGeneralTableEntry 15 } lacpInfoPortMoved OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Port Moved flag is set to true if the receive machine for a port is in the port_disabled state, and the combination of partner oper system and partner oper port number in use by the port has been used by received in an incoming LACPDU on a different port." ::= { lacpInfoPortGeneralTableEntry 16 } lacpInfoCollDetState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port collision and detection state" ::= { lacpInfoPortGeneralTableEntry 17 } lacpInfoPortRxState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port RX machine state" ::= { lacpInfoPortGeneralTableEntry 18 } lacpInfoPortMuxState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port Mux machine state" ::= { lacpInfoPortGeneralTableEntry 19 } lacpInfoPortPerState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "LACP port periodic machine state" ::= { lacpInfoPortGeneralTableEntry 20 } lacpInfoPortPerTraTimer OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Periodic Transmit Timer" ::= { lacpInfoPortGeneralTableEntry 21 } lacpInfoPortCurWhileTimer OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current While Timer" ::= { lacpInfoPortGeneralTableEntry 22 } lacpInfoPortOperState OBJECT-TYPE SYNTAX INTEGER { disabled(1), up(2), down(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of LACP on the port." ::= { lacpInfoPortGeneralTableEntry 23 } lacpInfoPortAdminTable OBJECT-TYPE SYNTAX SEQUENCE OF LacpInfoPortAdminTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LACP port admin information." ::= { lacpInfoPort 2 } lacpInfoPortAdminTableEntry OBJECT-TYPE SYNTAX LacpInfoPortAdminTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Admin information about a LACP port." INDEX { lacpInfoPortAdminIndex } ::= { lacpInfoPortAdminTable 1 } LacpInfoPortAdminTableEntry ::= SEQUENCE { lacpInfoPortAdminIndex PortNumber, lacpInfoPortActAdPortState DisplayString, lacpInfoPortActAdActiv INTEGER, lacpInfoPortActAdSync INTEGER, lacpInfoPortActAdDef INTEGER, lacpInfoPortActAdTimeout INTEGER, lacpInfoPortActAdColl INTEGER, lacpInfoPortActAdExp INTEGER, lacpInfoPortActAdAggr INTEGER, lacpInfoPortActAdDist INTEGER } lacpInfoPortAdminIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier." ::= { lacpInfoPortAdminTableEntry 1 } lacpInfoPortActAdPortState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Administrator Port. This is a octet mask with the following bits: Activity, Synchronization, Defaulted, Timeout, Collecting, Expired, Aggregation and Distributing. If all of them are 0 then the state is showed as 0x0, else it is displayed a blank state which mean is not a NULL state" ::= { lacpInfoPortAdminTableEntry 7 } lacpInfoPortActAdActiv OBJECT-TYPE SYNTAX INTEGER { active(1), passive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Administrator Port Activity" ::= { lacpInfoPortAdminTableEntry 8 } lacpInfoPortActAdSync OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Administrator Port Synchronization" ::= { lacpInfoPortAdminTableEntry 9 } lacpInfoPortActAdDef OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Administrator Port Defaulted" ::= { lacpInfoPortAdminTableEntry 10 } lacpInfoPortActAdTimeout OBJECT-TYPE SYNTAX INTEGER { short(1), long(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Administrator Port Timeout" ::= { lacpInfoPortAdminTableEntry 11 } lacpInfoPortActAdColl OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Administrator Port Collecting" ::= { lacpInfoPortAdminTableEntry 12 } lacpInfoPortActAdExp OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Administrator Port Expired" ::= { lacpInfoPortAdminTableEntry 13 } lacpInfoPortActAdAggr OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Administrator Port Aggregation" ::= { lacpInfoPortAdminTableEntry 14 } lacpInfoPortActAdDist OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Administrator Port Distributing" ::= { lacpInfoPortAdminTableEntry 15 } lacpInfoPortOperTable OBJECT-TYPE SYNTAX SEQUENCE OF LacpInfoPortOperTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of LACP port oper information." ::= { lacpInfoPort 3 } lacpInfoPortOperTableEntry OBJECT-TYPE SYNTAX LacpInfoPortOperTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Oper information about a LACP port." INDEX { lacpInfoPortOperIndex } ::= { lacpInfoPortOperTable 1 } LacpInfoPortOperTableEntry ::= SEQUENCE { lacpInfoPortOperIndex PortNumber, lacpInfoPortPartOpSysPrio Integer32, lacpInfoPortPartOpSysId DisplayString, lacpInfoPortPartOpKey Integer32, lacpInfoPortPartOpPortNum Integer32, lacpInfoPortPartOpPortPrio Integer32, lacpInfoPortActOpPortState DisplayString, lacpInfoPortActOpActiv INTEGER, lacpInfoPortActOpSync INTEGER, lacpInfoPortActOpDef INTEGER, lacpInfoPortActOpTimeout INTEGER, lacpInfoPortActOpColl INTEGER, lacpInfoPortActOpExp INTEGER, lacpInfoPortActOpAggr INTEGER, lacpInfoPortActOpDist INTEGER, lacpInfoPortPartOpPortState DisplayString, lacpInfoPortPartOpActiv INTEGER, lacpInfoPortPartOpSync INTEGER, lacpInfoPortPartOpDef INTEGER, lacpInfoPortPartOpTimeout INTEGER, lacpInfoPortPartOpColl INTEGER, lacpInfoPortPartOpExp INTEGER, lacpInfoPortPartOpAggr INTEGER, lacpInfoPortPartOpDist INTEGER } lacpInfoPortOperIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier." ::= { lacpInfoPortOperTableEntry 1 } lacpInfoPortPartOpSysPrio OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of Partner Operator Port System Priority" ::= { lacpInfoPortOperTableEntry 2 } lacpInfoPortPartOpSysId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The value of Partner Operator Port System ID" ::= { lacpInfoPortOperTableEntry 3 } lacpInfoPortPartOpKey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of Partner Operator Port Key" ::= { lacpInfoPortOperTableEntry 4 } lacpInfoPortPartOpPortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Partner Operator Port Number" ::= { lacpInfoPortOperTableEntry 5 } lacpInfoPortPartOpPortPrio OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of Partner Operator Port Priority" ::= { lacpInfoPortOperTableEntry 6 } lacpInfoPortActOpPortState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Operator Port. This is a octet mask with the following bits: Activity, Synchronization, Defaulted, Timeout, Collecting, Expired, Aggregation and Distributing. If all of them are 0 then the state is showed as 0x0, else it is displayed a blank state which mean is not a NULL state" ::= { lacpInfoPortOperTableEntry 7 } lacpInfoPortActOpActiv OBJECT-TYPE SYNTAX INTEGER { active(1), passive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Operator Port Activity" ::= { lacpInfoPortOperTableEntry 8 } lacpInfoPortActOpSync OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Operator Port Synchronization" ::= { lacpInfoPortOperTableEntry 9 } lacpInfoPortActOpDef OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Operator Port Defaulted" ::= { lacpInfoPortOperTableEntry 10 } lacpInfoPortActOpTimeout OBJECT-TYPE SYNTAX INTEGER { short(1), long(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Operator Port Timeout" ::= { lacpInfoPortOperTableEntry 11 } lacpInfoPortActOpColl OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Operator Port Collecting" ::= { lacpInfoPortOperTableEntry 12 } lacpInfoPortActOpExp OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Operator Port Expired" ::= { lacpInfoPortOperTableEntry 13 } lacpInfoPortActOpAggr OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Operator Port Aggregation" ::= { lacpInfoPortOperTableEntry 14 } lacpInfoPortActOpDist OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Actor Operator Port Distributing" ::= { lacpInfoPortOperTableEntry 15 } lacpInfoPortPartOpPortState OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Partner Operator Port. This is a octet mask with the following bits: Activity, Synchronization, Defaulted, Timeout, Collecting, Expired, Aggregation and Distributing. If all of them are 0 then the state is showed as 0x0, else it is displayed a blank state which mean is not a NULL state" ::= { lacpInfoPortOperTableEntry 16 } lacpInfoPortPartOpActiv OBJECT-TYPE SYNTAX INTEGER { active(1), passive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Partner Operator Port Activity" ::= { lacpInfoPortOperTableEntry 17 } lacpInfoPortPartOpSync OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Partner Operator Port Synchronization" ::= { lacpInfoPortOperTableEntry 18 } lacpInfoPortPartOpDef OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Partner Operator Port Defaulted" ::= { lacpInfoPortOperTableEntry 19 } lacpInfoPortPartOpTimeout OBJECT-TYPE SYNTAX INTEGER { short(1), long(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Partner Operator Port Timeout" ::= { lacpInfoPortOperTableEntry 20 } lacpInfoPortPartOpColl OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Partner Operator Port Collecting" ::= { lacpInfoPortOperTableEntry 21 } lacpInfoPortPartOpExp OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Partner Operator Port Expired" ::= { lacpInfoPortOperTableEntry 22 } lacpInfoPortPartOpAggr OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Partner Operator Port Aggregation" ::= { lacpInfoPortOperTableEntry 23 } lacpInfoPortPartOpDist OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Partner Operator Port Distributing" ::= { lacpInfoPortOperTableEntry 24 } -- CIST Information cistRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Root Identifier parameter in all Configuration Bridge PDUs originated by this node." ::= { cistGeneralInfo 1 } cistRootPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the path to the CIST Root as seen from this bridge." ::= { cistGeneralInfo 2 } cistRootPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge." ::= { cistGeneralInfo 3 } cistBridgeHelloTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time between the transmission of Configuration bridge PDUs in seconds." ::= { cistGeneralInfo 4 } cistBridgeMaxAge OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value in seconds that all bridges use for MaxAge when this bridge is acting as the root." ::= { cistGeneralInfo 5 } cistBridgeForwardDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value in seconds that all bridges use for ForwardDelay when this bridge is acting as the root." ::= { cistGeneralInfo 6 } cistRegionalRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the Root of the Multiple spanning tree region as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Regional Root Identifier parameter in all Configuration Bridge PDUs originated by this node." ::= { cistGeneralInfo 7 } cistRegionalPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Cost of the path to the CIST Regional Root as seen from this bridge." ::= { cistGeneralInfo 8 } mstpDigest OBJECT-TYPE SYNTAX DisplayString (SIZE(0..63)) MAX-ACCESS read-only STATUS current DESCRIPTION "The digest of the mstp." ::= { cistGeneralInfo 9 } -- CIST Port Information Table cistInfoPortTable OBJECT-TYPE SYNTAX SEQUENCE OF CistInfoPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of CIST Port information." ::= { cistInfo 2 } cistInfoPortTableEntry OBJECT-TYPE SYNTAX CistInfoPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular CIST Port." INDEX { cistInfoPortIndex } ::= { cistInfoPortTable 1 } CistInfoPortTableEntry ::= SEQUENCE { cistInfoPortIndex PortNumber, cistInfoPortPriority Integer32, cistInfoPortPathCost Integer32, cistInfoPortState INTEGER, cistInfoPortRole INTEGER, cistInfoPortDesignatedBridge BridgeId, cistInfoPortDesignatedPort OCTET STRING, cistInfoPortLinkType INTEGER, cistInfoPortHelloTime Integer32, cistInfoPortEdge INTEGER } cistInfoPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the port for which this entry contains spanning tree configuration." ::= { cistInfoPortTableEntry 1 } cistInfoPortPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting this value." ::= { cistInfoPortTableEntry 2 } cistInfoPortPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The contribution of this port to the path cost of paths towards the CIST Root which include this port." ::= { cistInfoPortTableEntry 3 } cistInfoPortState OBJECT-TYPE SYNTAX INTEGER { disabled (1), discarding (2), learning (4), forwarding (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current state of the Port as defined by the Common spanning tree protocol." ::= { cistInfoPortTableEntry 4 } cistInfoPortRole OBJECT-TYPE SYNTAX INTEGER { disabled(1), alternate(2), backup(3), root(4), designated(5), master(6), unknown(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Selected Port Role of the port for this spanning tree instance." ::= { cistInfoPortTableEntry 5 } cistInfoPortDesignatedBridge OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment." ::= { cistInfoPortTableEntry 6 } cistInfoPortDesignatedPort OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Port identifier of the port on the Designated Bridge for this port's segment." ::= { cistInfoPortTableEntry 7 } cistInfoPortLinkType OBJECT-TYPE SYNTAX INTEGER { p2p(1), shared(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The point-to-point status of the LAN segment attached to this port. A value of p2p (1) indicates that this port is being treated as if it is connected to a point-to-point link. A value of shared(2) indicates that this port is being treated as having a shared media connection." ::= { cistInfoPortTableEntry 8 } cistInfoPortHelloTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "CIST port Hello Time" ::= { cistInfoPortTableEntry 9 } cistInfoPortEdge OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port is an edge port or not. Returns disabled(2) when the port is not an edge port and returns enabled(1) when it is an edge port." ::= { cistInfoPortTableEntry 10 } -- General Information -- VLAN information vlanInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VLAN information." ::= { vlanInfo 1 } vlanInfoTableEntry OBJECT-TYPE SYNTAX VlanInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular VLAN." INDEX { vlanInfoId } ::= { vlanInfoTable 1 } VlanInfoTableEntry ::= SEQUENCE { vlanInfoId INTEGER, vlanInfoName DisplayString, vlanInfoStatus INTEGER, vlanInfoPorts OCTET STRING } vlanInfoId OBJECT-TYPE SYNTAX INTEGER (1..4090) MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN identifier." ::= { vlanInfoTableEntry 1 } vlanInfoName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN name." ::= { vlanInfoTableEntry 2 } vlanInfoStatus OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable, VLAN state information" ::= { vlanInfoTableEntry 3 } vlanInfoPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list information in the VLAN. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the VLAN 0 - The represented port does not belong to the VLAN" ::= { vlanInfoTableEntry 7 } -- L2 Operational commands -- ---------------------------------------------------------------------------- -- -- -- Virtual Link Aggregation (VLAG) -- -- -- -- ---------------------------------------------------------------------------- -- ---------------------------------------------------------------------------- -- Global VLAG Configuration -- ---------------------------------------------------------------------------- vlagCurIslCfgPortChannel OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Current vLAG ISL portchannel" DEFVAL { 0 } ::= { vlagIslCfg 1 } vlagNewIslCfgPortChannel OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to change the vLAG ISL portchannel." DEFVAL { 0 } ::= { vlagIslCfg 2 } vlagCurIslCfgAdminKey OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Current vLAG ISL admin key." DEFVAL { 0 } ::= { vlagIslCfg 3 } vlagNewIslCfgAdminKey OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to change the vLAG ISL admin key." DEFVAL { 0 } ::= { vlagIslCfg 4 } vlagCurCfgSwitchPriority OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Current vLAG switch priority" DEFVAL { 0 } ::= { vlagCfg 4 } vlagNewCfgSwitchPriority OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to change the vLAG priority of this switch." DEFVAL { 0 } ::= { vlagCfg 5 } -- Static Trunk table vlagCurCfgTrunkTable OBJECT-TYPE SYNTAX SEQUENCE OF VlagCurCfgTrunkTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects of the vLAG groups configured in this switch." ::= { vlagCfg 6 } vlagCurCfgTrunkTableEntry OBJECT-TYPE SYNTAX VlagCurCfgTrunkTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration objects for an vLAG group." INDEX { vlagCurCfgTrunkIndex } ::= { vlagCurCfgTrunkTable 1 } VlagCurCfgTrunkTableEntry ::= SEQUENCE { vlagCurCfgTrunkIndex Integer32, vlagCurCfgTrunkState INTEGER } vlagCurCfgTrunkIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the trunk group." ::= { vlagCurCfgTrunkTableEntry 1 } vlagCurCfgTrunkState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current administrative state of the vLAG group." DEFVAL { disabled } ::= { vlagCurCfgTrunkTableEntry 2 } vlagNewCfgTrunkTable OBJECT-TYPE SYNTAX SEQUENCE OF VlagNewCfgTrunkTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects of the vLAG groups configured in this switch." ::= { vlagCfg 7 } vlagNewCfgTrunkTableEntry OBJECT-TYPE SYNTAX VlagNewCfgTrunkTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration objects for an vLAG group." INDEX { vlagNewCfgTrunkIndex } ::= { vlagNewCfgTrunkTable 1 } VlagNewCfgTrunkTableEntry ::= SEQUENCE { vlagNewCfgTrunkIndex Integer32, vlagNewCfgTrunkState INTEGER } vlagNewCfgTrunkIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The identifier of the trunk group." ::= { vlagNewCfgTrunkTableEntry 1 } vlagNewCfgTrunkState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The new administrative state of the vLAG group." DEFVAL { disabled } ::= { vlagNewCfgTrunkTableEntry 2 } -- Dynamic Trunk table vlagCurCfgLacpTable OBJECT-TYPE SYNTAX SEQUENCE OF VlagCurCfgLacpTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects of the vLAG groups configured in this switch." ::= { vlagCfg 8 } vlagCurCfgLacpTableEntry OBJECT-TYPE SYNTAX VlagCurCfgLacpTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration objects for an vLAG group." INDEX { vlagCurCfgLacpKey } ::= { vlagCurCfgLacpTable 1 } VlagCurCfgLacpTableEntry ::= SEQUENCE { vlagCurCfgLacpKey INTEGER, vlagCurCfgLacpState INTEGER } vlagCurCfgLacpKey OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the trunk group." ::= { vlagCurCfgLacpTableEntry 1 } vlagCurCfgLacpState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current administrative state of the vLAG group." DEFVAL { disabled } ::= { vlagCurCfgLacpTableEntry 2 } vlagNewCfgLacpTable OBJECT-TYPE SYNTAX SEQUENCE OF VlagNewCfgLacpTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects of the vLAG groups configured in this switch." ::= { vlagCfg 9 } vlagNewCfgLacpTableEntry OBJECT-TYPE SYNTAX VlagNewCfgLacpTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration objects for an vLAG group." INDEX { vlagNewCfgLacpKey } ::= { vlagNewCfgLacpTable 1 } VlagNewCfgLacpTableEntry ::= SEQUENCE { vlagNewCfgLacpKey INTEGER, vlagNewCfgLacpState INTEGER } vlagNewCfgLacpKey OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of the trunk group." ::= { vlagNewCfgLacpTableEntry 1 } vlagNewCfgLacpState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The new administrative state of the vLAG group." DEFVAL { disabled } ::= { vlagNewCfgLacpTableEntry 2 } vlagCurCfgHlthchkPeerIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The current Health check Peer ip address." DEFVAL { '00000000'h } -- 0.0.0.0 ::= { vlagCfg 10 } vlagNewCfgHlthchkPeerIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The New Health check Peer ip address." DEFVAL { '00000000'h } -- 0.0.0.0 ::= { vlagCfg 11 } vlagCurCfgTierId OBJECT-TYPE SYNTAX INTEGER (0..512) MAX-ACCESS read-only STATUS current DESCRIPTION "Current vLAG Tier ID" DEFVAL { 0 } ::= { vlagCfg 12 } vlagNewCfgTierId OBJECT-TYPE SYNTAX INTEGER (0..512) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to change the vLAG Tier ID of this switch. vLAG consist of 2 vLAG peer switches connected by ISL link, the system formed by the switches is referred to as a vLAG tier. This object is used to specify the vLAG tier. And the tier id is used to generate vLAG system MAC." DEFVAL { 0 } ::= { vlagCfg 13 } vlagCurCfgStartupDelayInterval OBJECT-TYPE SYNTAX INTEGER (0..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "Current vLAG Startup delay interval" DEFVAL { 120 } ::= { vlagCfg 14 } vlagNewCfgStartupDelayInterval OBJECT-TYPE SYNTAX INTEGER (0..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to change the vLAG startup Delay Timer interval. The Timer is used to prevent traffic lost for the vLAG ports may be up before the ISL is up. The Timer is st- arted when the ISL is up and the role has been elected. And when the timer expires, all vLAG ports will be up. Before and during the timer running, all vLAG ports should be err- disabled." DEFVAL { 120 } ::= { vlagCfg 15 } vlagCurCfgGlobalEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current vLAG global status on switch." DEFVAL { disabled } ::= { vlagCfg 16 } vlagNewCfgGlobalEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set true to enable vLAG globally or Set false to disable vLAG globally on switch." DEFVAL { disabled } ::= { vlagCfg 17 } vlagCurCfgHlthchkConnectRetryInterval OBJECT-TYPE SYNTAX INTEGER (1..300) MAX-ACCESS read-only STATUS current DESCRIPTION "In case of healtcheck TCP connection can not be established, interval at which the retry attempt will be made to connect to the peer." DEFVAL { 30 } ::= { vlagCfg 18 } vlagNewCfgHlthchkConnectRetryInterval OBJECT-TYPE SYNTAX INTEGER (1..300) MAX-ACCESS read-write STATUS current DESCRIPTION "In case of healtcheck TCP connection can not be established, interval at which the retry attempt will be made to connect to the peer." DEFVAL { 30 } ::= { vlagCfg 19 } vlagCurCfgHlthchkKeepaliveAttempts OBJECT-TYPE SYNTAX INTEGER (1..24) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of keepalive attempts made before declaring peer is down. Within this time, atleast one of the keepalive message should have been received from the peer." DEFVAL { 3 } ::= { vlagCfg 20 } vlagNewCfgHlthchkKeepaliveAttempts OBJECT-TYPE SYNTAX INTEGER (1..24) MAX-ACCESS read-write STATUS current DESCRIPTION "Number of keepalive attempts made before declaring peer is down.Within this time, atleast one of the keepalive message should have been received from the peer." DEFVAL { 3 } ::= { vlagCfg 21 } vlagCurCfgHlthchkKeepaliveInterval OBJECT-TYPE SYNTAX INTEGER (2..300) MAX-ACCESS read-only STATUS current DESCRIPTION "Interval between keepalives sent over healthcheck TCP session to keep the session alive." DEFVAL { 5 } ::= { vlagCfg 22 } vlagNewCfgHlthchkKeepaliveInterval OBJECT-TYPE SYNTAX INTEGER (2..300) MAX-ACCESS read-write STATUS current DESCRIPTION "Interval between keepalives sent over healthcheck TCP session to keep the session alive." DEFVAL { 5 } ::= { vlagCfg 23 } vlagCurCfgAutoRecoveryInterval OBJECT-TYPE SYNTAX INTEGER (240..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "Current vLAG Auto Recovery interval" DEFVAL { 300 } ::= { vlagCfg 24 } vlagNewCfgAutoRecoveryInterval OBJECT-TYPE SYNTAX INTEGER (240..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to change the vLAG Auto Recovery Timer interval. The Timer is used to prevent all vlag ports stay in ErrDisabled state when booting two vLAG switches but one can not be up." DEFVAL { 300 } ::= { vlagCfg 25 } vlagCurCfgHlthchkPeerIpv6 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "The current Health check Peer ipv6 address." DEFVAL { "0:0:0:0:0:0:0:0" } ::= { vlagCfg 26 } vlagNewCfgHlthchkPeerIpv6 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "The New Health check Peer ipv6 address." DEFVAL { "0:0:0:0:0:0:0:0" } ::= { vlagCfg 27 } -- ---------------------------------------------------------------------------- -- Global VLAG Info -- ---------------------------------------------------------------------------- vlagInfoState OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current running state of vLAG." ::= { vlagInfoSystem 1 } vlagInfoAdminRole OBJECT-TYPE SYNTAX INTEGER { unelected(0), primary(1), secondary(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current running role of the switch. Role can be Primary(1), secondary(2) and unelected(3). Primary role indicates that the this switch controls the centralized operation in a vLAG domain. Secondary role indicates that this switch can take up the primary role when primary is not available. Unelected indicates that switches are not detected by one another" ::= {vlagInfoSystem 2 } vlagInfoISLId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "vLAG ISL trunk id." ::= {vlagInfoSystem 3 } vlagInfoLocalMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Local vLAG MAC address." ::= {vlagInfoSystem 4 } vlagInfoLocalPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Local vLAG Priority." ::= {vlagInfoSystem 5 } vlagInfoRemoteMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Remote vLAG MAC address." ::= {vlagInfoSystem 6 } vlagInfoRemotePriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Remote vLAG Priority." ::= {vlagInfoSystem 7 } vlagInfoHlthchkStatus OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current health check running status." ::= { vlagInfoSystem 8 } vlagInfoStartupDelayInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Startup Delay Timer Interval. The value may be different from vlagCurCfgStartupDelayInterval for the configuration of the interval after the timer is started can only take effect next startup." ::= {vlagInfoSystem 9 } vlagInfoStartupDelayStatus OBJECT-TYPE SYNTAX INTEGER { unstarted(1), running(2), finished(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Startup Delay Timer Status." ::= {vlagInfoSystem 10 } vlagInfoSystemMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "System vLAG MAC address" ::= {vlagInfoSystem 11 } vlagInfoOperaRole OBJECT-TYPE SYNTAX INTEGER { unelected(0), primary(1), secondary(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "vLAG switch operational role." ::= {vlagInfoSystem 12 } vlagInfoAutoRecoveryInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Auto Recovery Timer Interval. The value may be different from vlagCurCfgAutoRecoveryInterval for the configuration of the interval after the timer is started can only take effect next startup." ::= {vlagInfoSystem 13 } vlagInfoAutoRecoveryStatus OBJECT-TYPE SYNTAX INTEGER { unstarted(1), running(2), finished(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Auto Recovery Timer Status." ::= {vlagInfoSystem 14 } vlagInfoInstanceTable OBJECT-TYPE SYNTAX SEQUENCE OF VlagInfoInstanceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of objects of the running vLAG instances." ::= { vlagInfoGroup 1 } vlagInfoInstanceEntry OBJECT-TYPE SYNTAX VlagInfoInstanceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration objects for an vLAG group." INDEX { vlagInstanceId } ::= { vlagInfoInstanceTable 1 } VlagInfoInstanceEntry ::= SEQUENCE { vlagInstanceId Integer32, vlagInstanceTrunkId Integer32, vlagInstanceAdminKey Integer32, vlagInstanceState INTEGER } vlagInstanceId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of this instance." ::= { vlagInfoInstanceEntry 1 } vlagInstanceTrunkId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The trunk id of this vLAG instance." ::= { vlagInfoInstanceEntry 2 } vlagInstanceAdminKey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "AdminKey of this vLAG instance. Applicable only incase of dynamic trunks." ::= { vlagInfoInstanceEntry 3 } vlagInstanceState OBJECT-TYPE SYNTAX INTEGER { down(1), localUp(2), remoteUp(3), formed(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current running state of the vLAG instance." DEFVAL { down } ::= { vlagInfoInstanceEntry 4 } vlagInfoIslId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "vLAG ISL Id" ::= {vlagInfoIslGroup 1 } vlagInfoIslProtocol OBJECT-TYPE SYNTAX INTEGER { static(1), lacp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "vLAG ISL trunk group state Static - static trunk group Lacp - dynamic trunk group" ::= {vlagInfoIslGroup 3 } vlagInfoIslPortchannel OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "vLAG ISL portchannel number" ::= {vlagInfoIslGroup 4 } vlagInfoIslAdminkey OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "vLAG ISL lacp admin key" ::= {vlagInfoIslGroup 5 } vlagInfoIslPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list that forms the ISL. The ports are presented in bitmap format. OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to ISL 0 - The represented port does not belong to ISL" ::= {vlagInfoIslGroup 6 } vlagInfoIslPortState OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The ISL member ports' protocol state. The ports' protocol state are presented in bitmap format. OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to ISL and protocol state is up 0 - The represented port does not belong to ISL or protocol state is down" ::= {vlagInfoIslGroup 7 } vlagInfoIslPortLinkState OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The ISL member ports' link state. The ports' link state are presented in bitmap format. OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to ISL and link state is up 0 - The represented port does not belong to ISL or link state is down" ::= {vlagInfoIslGroup 8 } -- ---------------------------------------------------------------------------- -- Global VLAG Statistics -- ---------------------------------------------------------------------------- -- vlagStatsSystem OBJECT IDENTIFIER ::= { vlagStats 1 } -- vlagStatsIsl OBJECT IDENTIFIER ::= { vlagStats 2 } -- vlagStatsHealth OBJECT IDENTIFIER ::= { vlagStats 3 } -- vlagStatsLacp OBJECT IDENTIFIER ::= { vlagStats 4 } -- vlagStatsPdu OBJECT IDENTIFIER ::= { vlagStats 5 } -- vlagStatsIgmp OBJECT IDENTIFIER ::= { vlagStats 6 } vlagStatsClear OBJECT-TYPE SYNTAX INTEGER { clear(1), other(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'clear' will reset all statistics objects of VLAG. A get action of this object will always return 'other'. Setting this object to 'other' is not allowed." ::= { vlagStatsSystem 1 } vlagStatsIslInOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag ISL octets received." ::= { vlagStatsIsl 1 } vlagStatsIslInPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag ISL packets received." ::= { vlagStatsIsl 2 } vlagStatsIslOutOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag ISL octets sent." ::= { vlagStatsIsl 3 } vlagStatsIslOutPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag ISL packets sent." ::= { vlagStatsIsl 4 } vlagStatsPduSentRoleElection OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for role elections" ::= { vlagStatsPdu 1 } vlagStatsPduSentSystemInfo OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for system info" ::= { vlagStatsPdu 2 } vlagStatsPduSentFdbDynamicAdd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for addition of FDB dynamic entry" ::= { vlagStatsPdu 7 } vlagStatsPduSentFdbDynamicDel OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for deletion of FDB dynamic entry" ::= { vlagStatsPdu 8 } vlagStatsPduSentFdbInactiveAdd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for addition of FDB inactive entry" ::= { vlagStatsPdu 9 } vlagStatsPduSentFdbInactiveDel OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for deletion of FDB inactive entry" ::= { vlagStatsPdu 10 } vlagStatsPduSentHlthCheck OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for Health check" ::= { vlagStatsPdu 13 } vlagStatsPduSentOther OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for others" ::= { vlagStatsPdu 15 } vlagStatsPduSentUnknown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for unknowns" ::= { vlagStatsPdu 16 } vlagStatsPduRcvRoleElection OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for role elections" ::= { vlagStatsPdu 17 } vlagStatsPduRcvSystemInfo OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for system info" ::= { vlagStatsPdu 18 } vlagStatsPduRcvFdbDynamicAdd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for addition of FDB dynamic entry" ::= { vlagStatsPdu 23 } vlagStatsPduRcvFdbDynamicDel OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for deletion of FDB dynamic entry" ::= { vlagStatsPdu 24 } vlagStatsPduRcvFdbInactiveAdd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for addition of FDB inactive entry" ::= { vlagStatsPdu 25 } vlagStatsPduRcvFdbInactiveDel OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for deletion of FDB inactive entry" ::= { vlagStatsPdu 26 } vlagStatsPduRcvHlthCheck OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for Health check" ::= { vlagStatsPdu 29 } vlagStatsPduRcvOther OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for others" ::= { vlagStatsPdu 31 } vlagStatsPduRcvUnknown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for unknowns" ::= { vlagStatsPdu 32 } vlagStatsPduSentPeerInstanceEnable OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for peer instance enable" ::= { vlagStatsPdu 33 } vlagStatsPduSentPeerInstanceDisable OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for peer instance disable" ::= { vlagStatsPdu 34 } vlagStatsPduSentISLHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs sent for ISL hello" ::= { vlagStatsPdu 35 } vlagStatsPduRcvISLHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for ISL hello" ::= { vlagStatsPdu 36 } vlagStatsPduRcvPeerInstanceEnable OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for peer instance enable" ::= { vlagStatsPdu 37 } vlagStatsPduRcvPeerInstanceDisable OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of vlag PDUs received for peer instance disable" ::= { vlagStatsPdu 38 } vlagStatsIgmpReportsForwarded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP reports forwarded to the peer" ::= { vlagStatsIgmp 1 } vlagStatsIgmpLeavesForwarded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP leaves forwarded to the peer" ::= { vlagStatsIgmp 2 } -- ---------------------------------------------------------------------------- -- { INSERT: ecp -- ---------------------------------------------------------------------------- -- ------------------------------------------------------------------------- -- -- ECP Configuration { -- ------------------------------------------------------------------------- -- ecpCurCfgRetrans OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The ECP retransmission interval in millisecond" ::= { ecpCfg 1 } ecpNewCfgRetrans OBJECT-TYPE SYNTAX INTEGER (100..9000) MAX-ACCESS read-write STATUS current DESCRIPTION "The ECP retransmission interval in millisecond" ::= { ecpCfg 2 } -- ------------------------------------------------------------------------- -- -- ECP Configuration (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- ECP Information { -- ------------------------------------------------------------------------- -- ecpChnlInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF EcpChnlInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of ECP channel Info." ::= { ecpInfo 1 } ecpChnlInfoEntry OBJECT-TYPE SYNTAX EcpChnlInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about ECP channel." INDEX { ecpChnlInfoEntryIndex } ::= { ecpChnlInfoTable 1 } EcpChnlInfoEntry ::= SEQUENCE { ecpChnlInfoEntryIndex Integer32 ,ecpChnlPort Integer32 ,ecpChnlStag Integer32 ,ecpChnlSndlen Integer32 ,ecpChnlSndnxt Integer32 ,ecpChnlRcvlast Integer32 ,ecpChnlStateMachine Integer32 ,ecpChnlRxCnt Integer32 ,ecpChnlTxCnt Integer32 ,ecpChnlRxDrop Integer32 ,ecpChnlTxDrop Integer32 ,ecpChnlState INTEGER ,ecpChnlAckErr Integer32 } ecpChnlInfoEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ecp chnl info table." ::= { ecpChnlInfoEntry 1 } ecpChnlPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel port info." ::= { ecpChnlInfoEntry 2 } ecpChnlStag OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel stag info." ::= { ecpChnlInfoEntry 3 } ecpChnlSndlen OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel send length info." ::= { ecpChnlInfoEntry 4 } ecpChnlSndnxt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel send next info." ::= { ecpChnlInfoEntry 5 } ecpChnlRcvlast OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel recv last sequence info." ::= { ecpChnlInfoEntry 6 } ecpChnlStateMachine OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel state machineinfo." ::= { ecpChnlInfoEntry 7 } ecpChnlRxCnt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel Rx count info." ::= { ecpChnlInfoEntry 8 } ecpChnlTxCnt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel Tx count info." ::= { ecpChnlInfoEntry 9 } ecpChnlRxDrop OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel RxDrop info." ::= { ecpChnlInfoEntry 10 } ecpChnlTxDrop OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel TxDrop info." ::= { ecpChnlInfoEntry 11 } ecpChnlState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel state info." ::= { ecpChnlInfoEntry 12 } ecpChnlAckErr OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The ecp channel ACK error info." ::= { ecpChnlInfoEntry 13 } -- ------------------------------------------------------------------------- -- -- ECP Information (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- ECP Operation { -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- ECP Operation (end) } -- ------------------------------------------------------------------------- -- -- ---------------------------------------------------------------------------- -- -- -- Service Location Protocol (SLP) -- -- -- -- ---------------------------------------------------------------------------- -- ---------------------------------------------------------------------------- -- Global SLP Configuration -- ---------------------------------------------------------------------------- slpCfg OBJECT IDENTIFIER ::= { layer2Configs 20 } slpCurCfgGlobalEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current SLP global status on switch." DEFVAL { disabled } ::= { slpCfg 1 } slpNewCfgGlobalEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to enabled to enable SLP globally or Set to disabled to disable SLP globally on switch." DEFVAL { disabled } ::= { slpCfg 2 } slpCurCfgActiveDaDisEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current SLP active directory agent discovery status on switch." DEFVAL { disabled } ::= { slpCfg 3 } slpNewCfgActiveDaDisEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to enabled to enable SLP active directory agent discovery or Set to disabled to disable SLP active directory agent discovery on switch." DEFVAL { disabled } ::= { slpCfg 4 } slpCurCfgActiveDaDisStartWaitTime OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "Current SLP active directory agent discovery start wait time measured in seconds." DEFVAL { 3 } ::= { slpCfg 5 } slpNewCfgActiveDaDisStartWaitTime OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to change the SLP active directory agent discovery start wait time measured in seconds." DEFVAL { 3 } ::= { slpCfg 6 } -- ---------------------------------------------------------------------------- -- Global SLP Info -- ---------------------------------------------------------------------------- slpInfo OBJECT IDENTIFIER ::= { layer2Info 18 } slpInfoSystem OBJECT IDENTIFIER ::= { slpInfo 1 } slpInfoDirectoryAgents OBJECT IDENTIFIER ::= { slpInfo 2 } slpInfoUserAgents OBJECT IDENTIFIER ::= { slpInfo 3 } slpInfoProtocolVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "SLP protocol version." DEFVAL { 2 } ::= { slpInfoSystem 1 } slpInfoListeningPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "SLP listening port." DEFVAL { 427 } ::= { slpInfoSystem 2 } slpInfoListeningIPInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF SlpInfoListeningIPInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table with all the SLP listening IP interfaces." ::= { slpInfoSystem 3 } slpInfoListeningIPInterfaceEntry OBJECT-TYPE SYNTAX SlpInfoListeningIPInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration objects for a SLP listening IP interface." INDEX { listeningIPInterfaceId } ::= { slpInfoListeningIPInterfaceTable 1 } SlpInfoListeningIPInterfaceEntry ::= SEQUENCE { listeningIPInterfaceId Integer32, listeningIPInterfaceAddress IpAddress } listeningIPInterfaceId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of this IP interface." ::= { slpInfoListeningIPInterfaceEntry 1 } listeningIPInterfaceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The adddress of this IP interface." ::= { slpInfoListeningIPInterfaceEntry 2 } slpInfoDirectoryAgentsTable OBJECT-TYPE SYNTAX SEQUENCE OF SlpInfoDirectoryAgentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table with all the SLP Directory Agents." ::= { slpInfoDirectoryAgents 1 } slpInfoDirectoryAgentEntry OBJECT-TYPE SYNTAX SlpInfoDirectoryAgentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration objects for a Directory Agent entry." INDEX { directoryAgentAddress } ::= { slpInfoDirectoryAgentsTable 1 } SlpInfoDirectoryAgentEntry ::= SEQUENCE { directoryAgentAddress IpAddress, directoryAgentPort Integer32, directoryAgentTime Integer32 } directoryAgentAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP adddress of this Directory Agent." ::= { slpInfoDirectoryAgentEntry 1 } directoryAgentPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port of this Directory Agent. Communication can be done using TCP or UDP." ::= { slpInfoDirectoryAgentEntry 2 } directoryAgentTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time elapsed from the moment when this Directory Agent was learned measured in seconds." ::= { slpInfoDirectoryAgentEntry 3 } slpInfoUserAgentsTable OBJECT-TYPE SYNTAX SEQUENCE OF SlpInfoUserAgentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table with all the SLP User Agents." ::= { slpInfoUserAgents 1 } slpInfoUserAgentEntry OBJECT-TYPE SYNTAX SlpInfoUserAgentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration objects for a User Agent entry." INDEX { userAgentAddress } ::= { slpInfoUserAgentsTable 1 } SlpInfoUserAgentEntry ::= SEQUENCE { userAgentAddress IpAddress, userAgentPort Integer32, userAgentTime Integer32 } userAgentAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP adddress of this User Agent." ::= { slpInfoUserAgentEntry 1 } userAgentPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port of this User Agent. Communication can be done using TCP or UDP." ::= { slpInfoUserAgentEntry 2 } userAgentTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time elapsed from the moment when this User Agent was learned measured in seconds." ::= { slpInfoUserAgentEntry 3 } slpDirectoryAgentsClear OBJECT-TYPE SYNTAX INTEGER { clear(1), other(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'clear' will reset all directory agents settings of SLP. A get action of this object will always return 'other'. Setting this object to 'other' is not allowed." ::= { slpInfo 4 } -- ---------------------------------------------------------------------------- -- Global SLP Statistics -- ---------------------------------------------------------------------------- slpStats OBJECT IDENTIFIER ::= { layer2Stats 12 } slpCountersClear OBJECT-TYPE SYNTAX INTEGER { clear(1), other(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to 'clear' will reset all SLP counters. A get action of this object will always return 'other'. Setting this object to 'other' is not allowed." ::= { slpStats 3 } slpStatsTxCountersTable OBJECT-TYPE SYNTAX SEQUENCE OF SlpStatsTxCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table with all the SLP Send counters." ::= { slpStats 1 } slpStatsTxCounterEntry OBJECT-TYPE SYNTAX SlpStatsTxCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration objects for a SLP Send counter entry." INDEX { slpTxCounterIndex } ::= { slpStatsTxCountersTable 1 } SlpStatsTxCounterEntry ::= SEQUENCE { slpTxCounterIndex Integer32, slpTxCounterName DisplayString, slpTxCounterUnicast Integer32, slpTxCounterMulticast Integer32 } slpTxCounterIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of this counter." ::= { slpStatsTxCounterEntry 1 } slpTxCounterName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of this counter." ::= { slpStatsTxCounterEntry 2 } slpTxCounterUnicast OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The unicast value of this counter." ::= { slpStatsTxCounterEntry 3 } slpTxCounterMulticast OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast value of this counter." ::= { slpStatsTxCounterEntry 4 } slpStatsRxCountersTable OBJECT-TYPE SYNTAX SEQUENCE OF SlpStatsRxCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table with all the SLP Receive counters." ::= { slpStats 2 } slpStatsRxCounterEntry OBJECT-TYPE SYNTAX SlpStatsRxCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configuration objects for a SLP Receive counter entry." INDEX { slpRxCounterIndex } ::= { slpStatsRxCountersTable 1 } SlpStatsRxCounterEntry ::= SEQUENCE { slpRxCounterIndex Integer32, slpRxCounterName DisplayString, slpRxCounterUnicast Integer32, slpRxCounterMulticast Integer32 } slpRxCounterIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index this counter." ::= { slpStatsRxCounterEntry 1 } slpRxCounterName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of this counter." ::= { slpStatsRxCounterEntry 2 } slpRxCounterUnicast OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The unicast value of this counter." ::= { slpStatsRxCounterEntry 3 } slpRxCounterMulticast OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast value of this counter." ::= { slpStatsRxCounterEntry 4 } -- ---------------------------------------------------------------------------- -- } INSERT: layer2 -- ---------------------------------------------------------------------------- layer3 OBJECT IDENTIFIER ::= { g8052-mgmt 3 } -- ---------------------------------------------------------------------------- -- { INSERT: layer3 -- ---------------------------------------------------------------------------- layer3Configs OBJECT IDENTIFIER ::= { layer3 1 } layer3Stats OBJECT IDENTIFIER ::= { layer3 2 } layer3Info OBJECT IDENTIFIER ::= { layer3 3 } layer3Oper OBJECT IDENTIFIER ::= { layer3 4 } ipInterfaceCfg OBJECT IDENTIFIER ::= { layer3Configs 1 } ipInterfaceLoopbackCfg OBJECT IDENTIFIER ::= { layer3Configs 24 } ipGatewayCfg OBJECT IDENTIFIER ::= { layer3Configs 2 } ipStaticRouteCfg OBJECT IDENTIFIER ::= { layer3Configs 3 } ipForwardCfg OBJECT IDENTIFIER ::= { layer3Configs 4 } vrrpCfg OBJECT IDENTIFIER ::= { layer3Configs 6 } arpCfg OBJECT IDENTIFIER ::= { layer3Configs 7 } ipBootpCfg OBJECT IDENTIFIER ::= { layer3Configs 8 } dnsCfg OBJECT IDENTIFIER ::= { layer3Configs 9 } ipNwfCfg OBJECT IDENTIFIER ::= { layer3Configs 10 } ipRmapCfg OBJECT IDENTIFIER ::= { layer3Configs 11 } bgpCfg OBJECT IDENTIFIER ::= { layer3Configs 12 } ospfCfg OBJECT IDENTIFIER ::= { layer3Configs 13 } ipGeneralCfg OBJECT IDENTIFIER ::= { layer3Configs 14 } ipStaticArpCfg OBJECT IDENTIFIER ::= { layer3Configs 15 } rip2Cfg OBJECT IDENTIFIER ::= { layer3Configs 18 } igmpCfg OBJECT IDENTIFIER ::= { layer3Configs 19 } ipStaticNbrCfg OBJECT IDENTIFIER ::= { layer3Configs 21 } ipGatewayIpv6Cfg OBJECT IDENTIFIER ::= { layer3Configs 22 } ipStaticRoute6Cfg OBJECT IDENTIFIER ::= { layer3Configs 23 } ospf3Cfg OBJECT IDENTIFIER ::= { layer3Configs 26 } pptCfg OBJECT IDENTIFIER ::= { layer3Configs 27 } ipv6pmtuCfg OBJECT IDENTIFIER ::= { layer3Configs 28 } floodingCfg OBJECT IDENTIFIER ::= { layer3Configs 29 } mldCfg OBJECT IDENTIFIER ::= { layer3Configs 30 } ndprefixCfg OBJECT IDENTIFIER ::= { layer3Configs 31 } dhcpsnpCfg OBJECT IDENTIFIER ::= { layer3Configs 33 } ipsecCfg OBJECT IDENTIFIER ::= { layer3Configs 32 } arpStats OBJECT IDENTIFIER ::= { layer3Stats 2 } routeStats OBJECT IDENTIFIER ::= { layer3Stats 3 } dnsStats OBJECT IDENTIFIER ::= { layer3Stats 4 } vrrpStats OBJECT IDENTIFIER ::= { layer3Stats 5 } ospfStats OBJECT IDENTIFIER ::= { layer3Stats 6 } clearStats OBJECT IDENTIFIER ::= { layer3Stats 7 } igmpStats OBJECT IDENTIFIER ::= { layer3Stats 9 } ipv6Stats OBJECT IDENTIFIER ::= { layer3Stats 10} rip2Stats OBJECT IDENTIFIER ::= { layer3Stats 13 } ipStats OBJECT IDENTIFIER ::= { layer3Stats 16 } icmpStats OBJECT IDENTIFIER ::= { layer3Stats 17 } tcpStats OBJECT IDENTIFIER ::= { layer3Stats 18 } udpStats OBJECT IDENTIFIER ::= { layer3Stats 19 } bootpStats OBJECT IDENTIFIER ::= { layer3Stats 20 } ospf3Stats OBJECT IDENTIFIER ::= { layer3Stats 22 } mldStats OBJECT IDENTIFIER ::= { layer3Stats 23 } ipsecStats OBJECT IDENTIFIER ::= { layer3Stats 24 } nbrStats OBJECT IDENTIFIER ::= { layer3Stats 26 } dhcpsnpStats OBJECT IDENTIFIER ::= { layer3Stats 25} ipRoutingInfo OBJECT IDENTIFIER ::= { layer3Info 1 } ipEcmpRoutingInfo OBJECT IDENTIFIER ::= { layer3Info 19 } ipEcmpHash OBJECT IDENTIFIER ::= { layer3Info 20 } ipv6PmtuInfo OBJECT IDENTIFIER ::= { layer3Info 21} arpInfo OBJECT IDENTIFIER ::= { layer3Info 2 } vrrpInfo OBJECT IDENTIFIER ::= { layer3Info 3 } ospfinfo OBJECT IDENTIFIER ::= { layer3Info 4 } gatewayInfo OBJECT IDENTIFIER ::= { layer3Info 5 } igmpInfo OBJECT IDENTIFIER ::= { layer3Info 6 } nbrInfo OBJECT IDENTIFIER ::= { layer3Info 12 } gatewayIPv6Info OBJECT IDENTIFIER ::= { layer3Info 13 } ipRoute6Info OBJECT IDENTIFIER ::= { layer3Info 14 } ipInfo OBJECT IDENTIFIER ::= { layer3Info 8 } ipIntfInfo OBJECT IDENTIFIER ::= { layer3Info 9 } ipIntfLoopbackInfo OBJECT IDENTIFIER ::= { layer3Info 16 } rip2Info OBJECT IDENTIFIER ::= { layer3Info 10 } bgpInfo OBJECT IDENTIFIER ::= { layer3Info 11 } dhcpInfo OBJECT IDENTIFIER ::= { layer3Info 15 } ospf3Info OBJECT IDENTIFIER ::= { layer3Info 18 } mldInfo OBJECT IDENTIFIER ::= { layer3Info 22 } ipsecInfo OBJECT IDENTIFIER ::= { layer3Info 23 } dhcpsnpInfo OBJECT IDENTIFIER ::= { layer3Info 24 } -- ---------------------------------------------------------------------------- -- { INSERT: DHCP Snooping Config -- ---------------------------------------------------------------------------- dhcpSnoopingCurCfgOnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "DHCP Snooping ON/OFF settings." ::= { dhcpsnpCfg 1 } dhcpSnoopingNewCfgOnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "DHCP Snooping ON/OFF setting." ::= { dhcpsnpCfg 2 } dhcpSnoopingCurCfgOption82OnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "on/off state of DHCP Snooping option82." ::= { dhcpsnpCfg 3 } dhcpSnoopingNewCfgOption82OnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable DHCP Snooping option82" ::= { dhcpsnpCfg 4 } dhcpSnoopingCurCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF DHCPSnoopingCurCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "DHCP Snooping Port Configuration Table." ::= { dhcpsnpCfg 5 } dhcpSnoopingCurCfgPortTableEntry OBJECT-TYPE SYNTAX DHCPSnoopingCurCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in DHCP Snooping Port Configuration Table" INDEX { dhcpSnoopingCurCfgPortId } ::= { dhcpSnoopingCurCfgPortTable 1 } DHCPSnoopingCurCfgPortTableEntry ::= SEQUENCE { dhcpSnoopingCurCfgPortId Integer32, dhcpSnoopingCurCfgPortTrusted INTEGER, dhcpSnoopingCurCfgPortRateLimit Integer32 } dhcpSnoopingCurCfgPortId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Port ID of this DHCP Snooping port configration." ::= { dhcpSnoopingCurCfgPortTableEntry 1 } dhcpSnoopingCurCfgPortTrusted OBJECT-TYPE SYNTAX INTEGER { trusted(1), untrusted(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set port as trusted or untrusted port." ::= { dhcpSnoopingCurCfgPortTableEntry 2 } dhcpSnoopingCurCfgPortRateLimit OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Set port DHCP packet rate limit(pps). Its ranges is 0 ~ 2048, set 0 to disable rate limit." ::= { dhcpSnoopingCurCfgPortTableEntry 3 } dhcpSnoopingNewCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF DHCPSnoopingNewCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "DHCP Snooping Port Configuration Table." ::= { dhcpsnpCfg 6 } dhcpSnoopingNewCfgPortTableEntry OBJECT-TYPE SYNTAX DHCPSnoopingNewCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the DHCP Snooping Port Configuration Table" INDEX { dhcpSnoopingNewCfgportId } ::= { dhcpSnoopingNewCfgPortTable 1 } DHCPSnoopingNewCfgPortTableEntry ::= SEQUENCE { dhcpSnoopingNewCfgportId Integer32, dhcpSnoopingNewCfgportTrusted INTEGER, dhcpSnoopingNewCfgportRateLimit Integer32 } dhcpSnoopingNewCfgportId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Port ID of this DHCP Snooping port configration." ::= { dhcpSnoopingNewCfgPortTableEntry 1 } dhcpSnoopingNewCfgportTrusted OBJECT-TYPE SYNTAX INTEGER { trusted(1), untrusted(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set port as trusted or untrusted port." ::= { dhcpSnoopingNewCfgPortTableEntry 2 } dhcpSnoopingNewCfgportRateLimit OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Set port DHCP packet rate limit(pps). Set 0 to disable rate limit." ::= { dhcpSnoopingNewCfgPortTableEntry 3 } dhcpSnoopingCurCfgVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF DHCPSnoopingCurCfgVlanTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "DHCP Snooping VLAN Table." ::= { dhcpsnpCfg 7 } dhcpSnoopingCurCfgVlanTableEntry OBJECT-TYPE SYNTAX DHCPSnoopingCurCfgVlanTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the DHCP Snooping VLAN Table" INDEX { dhcpSnoopingCurCfgVlanId } ::= { dhcpSnoopingCurCfgVlanTable 1 } DHCPSnoopingCurCfgVlanTableEntry ::= SEQUENCE { dhcpSnoopingCurCfgVlanId Integer32, dhcpSnoopingCurCfgVlanOnState INTEGER } dhcpSnoopingCurCfgVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of this DHCP Snooping VLAN configration." ::= { dhcpSnoopingCurCfgVlanTableEntry 1 } dhcpSnoopingCurCfgVlanOnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "on/off state of DHCP Snooping on this VLAN." ::= { dhcpSnoopingCurCfgVlanTableEntry 2 } dhcpSnoopingNewCfgVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF DHCPSnoopingNewCfgVLANTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "DHCP Snooping VLAN Table." ::= { dhcpsnpCfg 8 } dhcpSnoopingNewCfgVlanTableEntry OBJECT-TYPE SYNTAX DHCPSnoopingNewCfgVLANTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the DHCP Snooping VLAN Table" INDEX { dhcpSnoopingNewCfgVlanId } ::= { dhcpSnoopingNewCfgVlanTable 1 } DHCPSnoopingNewCfgVLANTableEntry ::= SEQUENCE { dhcpSnoopingNewCfgVlanId Integer32, dhcpSnoopingNewCfgVlanOnState INTEGER } dhcpSnoopingNewCfgVlanId OBJECT-TYPE SYNTAX Integer32 (1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of this DHCP Snooping VLAN configration." ::= { dhcpSnoopingNewCfgVlanTableEntry 1 } dhcpSnoopingNewCfgVlanOnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable DHCP Snooping on this VLAN." ::= { dhcpSnoopingNewCfgVlanTableEntry 2 } dhcpSnoopingBindingInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF DHCPSnoopingBindingInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "DHCP Snooping binding Table." ::= { dhcpsnpInfo 1 } dhcpSnoopingBindingInfoEntry OBJECT-TYPE SYNTAX DHCPSnoopingBindingInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the DHCP Snooping binding Table" INDEX { dhcpSnoopingBindingInfoIndex } ::= { dhcpSnoopingBindingInfoTable 1 } DHCPSnoopingBindingInfoEntry ::= SEQUENCE { dhcpSnoopingBindingInfoIndex Integer32, dhcpSnoopingBindingInfoMac OCTET STRING, dhcpSnoopingBindingInfoIp IpAddress, dhcpSnoopingBindingInfoVLAN Integer32, dhcpSnoopingBindingInfoPort Integer32, dhcpSnoopingBindingInfoExpiry Unsigned32, dhcpSnoopingBindingInfoType INTEGER } dhcpSnoopingBindingInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Index of this DHCP Snooping binding entry." ::= { dhcpSnoopingBindingInfoEntry 1 } dhcpSnoopingBindingInfoMac OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Mac Address of this DHCP Snooping binding entry." ::= { dhcpSnoopingBindingInfoEntry 2 } dhcpSnoopingBindingInfoIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Ip Address of this DHCP Snooping binding entry." ::= { dhcpSnoopingBindingInfoEntry 3 } dhcpSnoopingBindingInfoVLAN OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "VLAN ID of this DHCP Snooping binding entry." ::= { dhcpSnoopingBindingInfoEntry 4 } dhcpSnoopingBindingInfoPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Port Number of this DHCP Snooping binding entry." ::= { dhcpSnoopingBindingInfoEntry 5 } dhcpSnoopingBindingInfoExpiry OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The lease time of this DHCP Snooping binding entry. Set 0 to remove this entry" ::= { dhcpSnoopingBindingInfoEntry 6 } dhcpSnoopingBindingInfoType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Show How this DHCP Snooping binding entry come from." ::= { dhcpSnoopingBindingInfoEntry 7 } -- ---------------------------------------------------------------------------- -- { INSERT: DHCP Snooping stat -- ---------------------------------------------------------------------------- dhcpSnoopingStatInPacketRequest OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter of DHCP REQUEST messages received." ::= { dhcpsnpStats 1 } dhcpSnoopingStatInPacketReply OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter of DHCP REPLY messages received." ::= { dhcpsnpStats 2 } dhcpSnoopingStatDroppedPacketInvalid OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter of dropped DHCP messages due to invalid packet." ::= { dhcpsnpStats 3 } dhcpSnoopingStatDroppedPacketRateLimit OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter of dropped DHCP messages due to Rate Limit in software." ::= { dhcpsnpStats 4 } dhcpSnoopingStatDroppedPacketOther OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Counter of dropped DHCP messages due to other reason." ::= { dhcpsnpStats 5 } vrrpOper OBJECT IDENTIFIER ::= { layer3Oper 1 } dhcpInfoMacAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the interface." ::= { dhcpInfo 1} dhcpInfoAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the interface." ::= { dhcpInfo 2} dhcpInfoSubnetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The subnet mask of the interface." ::= { dhcpInfo 3} dhcpInfoDefaultGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of default gateway for the interface." ::= { dhcpInfo 4} dhcpInfoServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the DHCP server that leased the ip of the interface." ::= { dhcpInfo 5} dhcpInfoLeaseObtained OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The time and date when the lease was obtained ." ::= { dhcpInfo 6} dhcpInfoLeaseExpires OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The time and date when the lease was obtained ." ::= { dhcpInfo 7} -- IP Configuration ipInterfaceTableMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the IP interface table." ::= { ipInterfaceCfg 1 } ipCurCfgIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP interface configuration." ::= { ipInterfaceCfg 2 } ipCurCfgIntfEntry OBJECT-TYPE SYNTAX IpCurCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Ip interface table" INDEX { ipCurCfgIntfIndex } ::= { ipCurCfgIntfTable 1 } IpCurCfgIntfEntry ::= SEQUENCE { ipCurCfgIntfIndex Integer32, ipCurCfgIntfAddr DisplayString, ipCurCfgIntfMask DisplayString, ipCurCfgIntfBroadcast IpAddress, ipCurCfgIntfState INTEGER, ipCurCfgIntfBootpRelay INTEGER, ipCurCfgIntfRouteAdv INTEGER, ipCurCfgIntfManagedCfg INTEGER, ipCurCfgIntfOtherCfg INTEGER, ipCurCfgIntfAdvLifetime INTEGER, ipCurCfgIntfDadAttempts INTEGER, ipCurCfgIntfReachTime Gauge32, ipCurCfgIntfAdvInterval INTEGER, ipCurCfgIntfAdvIntervalMin INTEGER, ipCurCfgIntfRetransmitTimer Gauge32, ipCurCfgIntfHopLimit INTEGER, ipCurCfgIntfAdvMtu INTEGER, ipCurCfgIntfIp6Host INTEGER, ipCurCfgIntfIp6Dstun INTEGER, ipCurCfgSecIntfAddr DisplayString, ipCurCfgSecIntfPrefix Integer32, ipCurCfgSecIntfAnycast INTEGER, ipCurCfgIntfAnycast INTEGER, ipCurCfgIntfVlan Integer32 } ipCurCfgIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number for which the IP information is related." ::= { ipCurCfgIntfEntry 1} ipCurCfgIntfAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "This field configures the new IP/IPv6 addr of the interface. Address should be IPv4 dotted-quads or IPv6 16-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { ipCurCfgIntfEntry 2 } ipCurCfgIntfMask OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "The subnet mask as IPv4 dotted-quads OR the IPv6 prefix length (integer in range 0..128) associated with this IP address ." ::= { ipCurCfgIntfEntry 3 } ipCurCfgIntfBroadcast OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The broadcast address of the interface." ::= { ipCurCfgIntfEntry 4 } ipCurCfgIntfVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN associated with the interface." ::= { ipCurCfgIntfEntry 5 } ipCurCfgIntfState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the interface." ::= { ipCurCfgIntfEntry 6 } ipCurCfgIntfBootpRelay OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable BOOTP relay." ::= { ipCurCfgIntfEntry 7 } ipCurCfgIntfRouteAdv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable route advertisement of the interface." ::= { ipCurCfgIntfEntry 12 } ipCurCfgIntfManagedCfg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Managed config flag of the interface, which allows the host to use DHCP for address configuration." ::= { ipCurCfgIntfEntry 13 } ipCurCfgIntfOtherCfg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Other config flag of the interface, which allows the host to use DHCP for other stateful configuration." ::= { ipCurCfgIntfEntry 14 } ipCurCfgIntfAdvLifetime OBJECT-TYPE SYNTAX INTEGER (0..9000) MAX-ACCESS read-only STATUS current DESCRIPTION "Set Router Advertisement lifetime of the interface." ::= { ipCurCfgIntfEntry 15 } ipCurCfgIntfDadAttempts OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "Set the number of duplicate address detection (dad) attempts of the interface." ::= { ipCurCfgIntfEntry 16 } ipCurCfgIntfReachTime OBJECT-TYPE SYNTAX Gauge32 (0..3600000) MAX-ACCESS read-only STATUS current DESCRIPTION "Set the advertised reachability time of the interface in ms." ::= { ipCurCfgIntfEntry 17 } ipCurCfgIntfAdvInterval OBJECT-TYPE SYNTAX INTEGER (4..1800) MAX-ACCESS read-only STATUS current DESCRIPTION "Set the IPv6 Router Advertisement interval of the interface." ::= { ipCurCfgIntfEntry 18 } ipCurCfgIntfAdvIntervalMin OBJECT-TYPE SYNTAX INTEGER (3..1350) MAX-ACCESS read-only STATUS current DESCRIPTION "Set the IPv6 Router Advertisement Minimum interval limit of the interface." ::= { ipCurCfgIntfEntry 19 } ipCurCfgIntfRetransmitTimer OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "Set the IPv6 Router Advertisement Retransmit Timer in ms." ::= { ipCurCfgIntfEntry 20 } ipCurCfgIntfHopLimit OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Set the IPv6 Router Advertisement Current Hop Limit" ::= { ipCurCfgIntfEntry 21 } ipCurCfgIntfAdvMtu OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable Advertise MTU option." ::= { ipCurCfgIntfEntry 22 } ipCurCfgIntfIp6Host OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable IPv6 host mode on the interface." ::= { ipCurCfgIntfEntry 23 } ipCurCfgSecIntfAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "This field configures the new IP/IPv6 addr of the interface. Address should be in IPv6 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { ipCurCfgIntfEntry 25 } ipCurCfgSecIntfPrefix OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 prefix length (integer in range 0..128) associated with this IP address ." ::= { ipCurCfgIntfEntry 26 } ipCurCfgIntfAnycast OBJECT-TYPE SYNTAX INTEGER { anycast(1), none(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This field has the value of anycast(1) if IPv6 interface address is anycast and none(2) if not." ::= { ipCurCfgIntfEntry 27 } ipCurCfgSecIntfAnycast OBJECT-TYPE SYNTAX INTEGER { anycast(1), none(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This field has the value of anycast(1) if secondary IPv6 interface address is anycast and none(2) if not." ::= { ipCurCfgIntfEntry 28 } ipCurCfgIntfIp6Dstun OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable sending of ICMP Unreachable messages." ::= { ipCurCfgIntfEntry 29 } ipNewCfgIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of interface in the new configuration block." ::= { ipInterfaceCfg 3 } ipNewCfgIntfEntry OBJECT-TYPE SYNTAX IpNewCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Ip interface table" INDEX { ipNewCfgIntfIndex } ::= { ipNewCfgIntfTable 1 } IpNewCfgIntfEntry ::= SEQUENCE { ipNewCfgIntfIndex Integer32, ipNewCfgIntfAddr DisplayString, ipNewCfgIntfMask DisplayString, ipNewCfgIntfVlan Integer32, ipNewCfgIntfState INTEGER, ipNewCfgIntfBootpRelay INTEGER, ipNewCfgIntfRouteAdv INTEGER, ipNewCfgIntfIp6Host INTEGER, ipNewCfgIntfIp6Dstun INTEGER, ipNewCfgIntfManagedCfg INTEGER, ipNewCfgIntfOtherCfg INTEGER, ipNewCfgIntfAdvLifetime INTEGER, ipNewCfgIntfDadAttempts INTEGER, ipNewCfgIntfReachTime Gauge32, ipNewCfgIntfAdvInterval INTEGER, ipNewCfgIntfAdvIntervalMin INTEGER, ipNewCfgIntfRetransmitTimer Gauge32, ipNewCfgIntfHopLimit INTEGER, ipNewCfgIntfAdvMtu INTEGER, ipNewCfgSecIntfAddr DisplayString, ipNewCfgSecIntfPrefix Integer32, ipNewCfgSecIntfAnycast INTEGER, ipNewCfgIntfAnycast INTEGER, ipNewCfgIntfDelete INTEGER } ipNewCfgIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number for which the IP information is related." ::= { ipNewCfgIntfEntry 1 } ipNewCfgIntfAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "This field configures the new IP/IPv6 addr of the interface. Address should be IPv4 dotted-quads or IPv6 16-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { ipNewCfgIntfEntry 2 } ipNewCfgIntfMask OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) MAX-ACCESS read-create STATUS current DESCRIPTION "The subnet mask as IPv4 dotted-quads OR the IPv6 prefix length (integer in range 0..128) associated with this IP address ." ::= { ipNewCfgIntfEntry 3 } ipNewCfgIntfVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The VLAN associated with the interface." ::= { ipNewCfgIntfEntry 5 } ipNewCfgIntfState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the interface." ::= { ipNewCfgIntfEntry 6 } ipNewCfgIntfDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ipNewCfgIntfEntry 7 } ipNewCfgIntfBootpRelay OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable BOOTP relay." ::= { ipNewCfgIntfEntry 8 } ipNewCfgIntfRouteAdv OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable route advertisement of the interface." ::= { ipNewCfgIntfEntry 13 } ipNewCfgIntfManagedCfg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable Managed config flag of the interface, which allows the host to use DHCP for address configuration." ::= { ipNewCfgIntfEntry 14 } ipNewCfgIntfOtherCfg OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable Other config flag of the interface, which allows the host to use DHCP for other stateful configuration." ::= { ipNewCfgIntfEntry 15 } ipNewCfgIntfAdvLifetime OBJECT-TYPE SYNTAX INTEGER (0..9000) MAX-ACCESS read-create STATUS current DESCRIPTION "Set Router Advertisement lifetime of the interface." ::= { ipNewCfgIntfEntry 16 } ipNewCfgIntfDadAttempts OBJECT-TYPE SYNTAX INTEGER (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "Set the number of duplicate address detection (dad) attempts of the interface." ::= { ipNewCfgIntfEntry 17 } ipNewCfgIntfReachTime OBJECT-TYPE SYNTAX Gauge32 (0..3600000) MAX-ACCESS read-create STATUS current DESCRIPTION "Set the advertised reachability time of the interface in ms." ::= { ipNewCfgIntfEntry 18 } ipNewCfgIntfAdvInterval OBJECT-TYPE SYNTAX INTEGER (4..1800) MAX-ACCESS read-create STATUS current DESCRIPTION "Set the IPv6 Router Advertisement interval of the interface." ::= { ipNewCfgIntfEntry 19 } ipNewCfgIntfAdvIntervalMin OBJECT-TYPE SYNTAX INTEGER (3..1350) MAX-ACCESS read-create STATUS current DESCRIPTION "Set the IPv6 Router Advertisement Minimum interval limit of the interface." ::= { ipNewCfgIntfEntry 20 } ipNewCfgIntfRetransmitTimer OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "Set the IPv6 Router Advertisement Retransmit Timer in ms." ::= { ipNewCfgIntfEntry 21 } ipNewCfgIntfHopLimit OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Set the IPv6 Router Advertisement Current Hop Limit" ::= { ipNewCfgIntfEntry 22 } ipNewCfgIntfAdvMtu OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable Advertise MTU option." ::= { ipNewCfgIntfEntry 23 } ipNewCfgIntfIp6Host OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable IPv6 host mode on the interface." ::= { ipNewCfgIntfEntry 24 } ipNewCfgSecIntfAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "This field configures the new IPv6 addr of the interface. Address should be in IPv6 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { ipNewCfgIntfEntry 26 } ipNewCfgSecIntfPrefix OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The IPv6 prefix length (integer in range 0..128) associated with this IP address ." ::= { ipNewCfgIntfEntry 27 } ipNewCfgIntfAnycast OBJECT-TYPE SYNTAX INTEGER { anycast(1), none(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This field has the value of anycast(1) if IPv6 interface address is anycast and none(2) if not." ::= { ipNewCfgIntfEntry 28 } ipNewCfgSecIntfAnycast OBJECT-TYPE SYNTAX INTEGER { anycast(1), none(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This field has the value of anycast(1) if secondary IPv6 interface address is anycast and none(2) if not." ::= { ipNewCfgIntfEntry 29 } ipNewCfgIntfIp6Dstun OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable sending of ICMP Unreachable messages." ::= { ipNewCfgIntfEntry 30 } -- IP Loopback Configuration ipInterfaceLoopbackTableMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the IP Loopback interface table." ::= { ipInterfaceLoopbackCfg 1 } ipCurCfgIntfLoopbackTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgIntfLoopbackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP Loopback interface configuration." ::= { ipInterfaceLoopbackCfg 2 } ipCurCfgIntfLoopbackEntry OBJECT-TYPE SYNTAX IpCurCfgIntfLoopbackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Ip Loopback interface table" INDEX { ipCurCfgIntfLoopbackIndex } ::= { ipCurCfgIntfLoopbackTable 1 } IpCurCfgIntfLoopbackEntry ::= SEQUENCE { ipCurCfgIntfLoopbackIndex Integer32, ipCurCfgIntfLoopbackAddr IpAddress, ipCurCfgIntfLoopbackMask IpAddress, ipCurCfgIntfLoopbackBroadcast IpAddress, ipCurCfgIntfLoopbackState INTEGER } ipCurCfgIntfLoopbackIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Loopback interface number for which the IP information is related." ::= { ipCurCfgIntfLoopbackEntry 1} ipCurCfgIntfLoopbackAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the interface." ::= { ipCurCfgIntfLoopbackEntry 2 } ipCurCfgIntfLoopbackMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The subnet mask of the interface." ::= { ipCurCfgIntfLoopbackEntry 3 } ipCurCfgIntfLoopbackBroadcast OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The broadcast address of the interface." ::= { ipCurCfgIntfLoopbackEntry 4 } ipCurCfgIntfLoopbackState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the interface." ::= { ipCurCfgIntfLoopbackEntry 6 } ipNewCfgIntfLoopbackTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgIntfLoopbackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of loopback interface in the new configuration block." ::= { ipInterfaceLoopbackCfg 3 } ipNewCfgIntfLoopbackEntry OBJECT-TYPE SYNTAX IpNewCfgIntfLoopbackEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Ip Loopback interface table" INDEX { ipNewCfgIntfLoopbackIndex } ::= { ipNewCfgIntfLoopbackTable 1 } IpNewCfgIntfLoopbackEntry ::= SEQUENCE { ipNewCfgIntfLoopbackIndex Integer32, ipNewCfgIntfLoopbackAddr IpAddress, ipNewCfgIntfLoopbackMask IpAddress, ipNewCfgIntfLoopbackState INTEGER, ipNewCfgIntfLoopbackDelete INTEGER } ipNewCfgIntfLoopbackIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Loopback interface number for which the IP information is related." ::= { ipNewCfgIntfLoopbackEntry 1 } ipNewCfgIntfLoopbackAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of the interface." ::= { ipNewCfgIntfLoopbackEntry 2 } ipNewCfgIntfLoopbackMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The subnet mask of the interface." ::= { ipNewCfgIntfLoopbackEntry 3 } ipNewCfgIntfLoopbackState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the interface." ::= { ipNewCfgIntfLoopbackEntry 6 } ipNewCfgIntfLoopbackDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ipNewCfgIntfLoopbackEntry 7 } -- IP Gateway Table Configuration ipGatewayTableMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the IP gateway table." ::= { ipGatewayCfg 3 } ipCurCfgGwTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgGwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of gateways in the current configuration block." ::= { ipGatewayCfg 4 } ipCurCfgGwEntry OBJECT-TYPE SYNTAX IpCurCfgGwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Ip gateway table" INDEX { ipCurCfgGwIndex } ::= { ipCurCfgGwTable 1 } IpCurCfgGwEntry ::= SEQUENCE { ipCurCfgGwIndex Integer32, ipCurCfgGwAddr IpAddress, ipCurCfgGwInterval INTEGER, ipCurCfgGwRetry INTEGER, ipCurCfgGwArp INTEGER, ipCurCfgGwState INTEGER } ipCurCfgGwIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The gateway number for which the information is related." ::= { ipCurCfgGwEntry 1} ipCurCfgGwAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the default gateway." ::= { ipCurCfgGwEntry 2 } ipCurCfgGwInterval OBJECT-TYPE SYNTAX INTEGER (0..60) MAX-ACCESS read-only STATUS current DESCRIPTION "The interval between ping attempts." ::= { ipCurCfgGwEntry 3 } ipCurCfgGwRetry OBJECT-TYPE SYNTAX INTEGER (1..120) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failed attempts to declare the default gateway DOWN." ::= { ipCurCfgGwEntry 4 } ipCurCfgGwState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the default gateway." ::= { ipCurCfgGwEntry 5 } ipCurCfgGwArp OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of ARP only health checks." ::= { ipCurCfgGwEntry 6 } ipNewCfgGwTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgGwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of gateway in the new configuration block." ::= { ipGatewayCfg 5 } ipNewCfgGwEntry OBJECT-TYPE SYNTAX IpNewCfgGwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Ip default gateway table" INDEX { ipNewCfgGwIndex } ::= { ipNewCfgGwTable 1 } IpNewCfgGwEntry ::= SEQUENCE { ipNewCfgGwIndex Integer32, ipNewCfgGwAddr IpAddress, ipNewCfgGwInterval INTEGER, ipNewCfgGwRetry INTEGER, ipNewCfgGwState INTEGER, ipNewCfgGwArp INTEGER, ipNewCfgGwDelete INTEGER } ipNewCfgGwIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The gateway number for which the information is related." ::= { ipNewCfgGwEntry 1} ipNewCfgGwAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of the default gateway." ::= { ipNewCfgGwEntry 2 } ipNewCfgGwInterval OBJECT-TYPE SYNTAX INTEGER (0..60) MAX-ACCESS read-create STATUS current DESCRIPTION "The interval in seconds between ping attempts." ::= { ipNewCfgGwEntry 3 } ipNewCfgGwRetry OBJECT-TYPE SYNTAX INTEGER (1..120) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of failed attempts to declare the default gateway DOWN." ::= { ipNewCfgGwEntry 4 } ipNewCfgGwState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the default gateway." ::= { ipNewCfgGwEntry 5 } ipNewCfgGwDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ipNewCfgGwEntry 6 } ipNewCfgGwArp OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the ARP only health checks." ::= { ipNewCfgGwEntry 7 } -- -- IP Static Route Configuration -- ipStaticRouteTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the Static Route table." ::= { ipStaticRouteCfg 1 } ipCurCfgStaticRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgStaticRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of static routes in the current configuration block." ::= { ipStaticRouteCfg 2 } ipCurCfgStaticRouteEntry OBJECT-TYPE SYNTAX IpCurCfgStaticRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static IP route table" INDEX { ipCurCfgStaticRouteIndx } ::= { ipCurCfgStaticRouteTable 1 } IpCurCfgStaticRouteEntry ::= SEQUENCE { ipCurCfgStaticRouteIndx Integer32, ipCurCfgStaticRouteDestIp IpAddress, ipCurCfgStaticRouteMask IpAddress, ipCurCfgStaticRouteGateway IpAddress, ipCurCfgStaticRouteInterface Integer32 } ipCurCfgStaticRouteIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the static routing table." ::= { ipCurCfgStaticRouteEntry 1} ipCurCfgStaticRouteDestIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address of this route." ::= { ipCurCfgStaticRouteEntry 2} ipCurCfgStaticRouteMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The current subnet mask of this route." ::= { ipCurCfgStaticRouteEntry 3} ipCurCfgStaticRouteGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The current gateway of this route." ::= { ipCurCfgStaticRouteEntry 4} ipCurCfgStaticRouteInterface OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The IP interface of this route. The IP address of the specified interface shall be use as source IP when performs routing." ::= { ipCurCfgStaticRouteEntry 5} ipNewCfgStaticRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgStaticRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of static routes in the new configuration block." ::= { ipStaticRouteCfg 3 } ipStaticRouteClearAllByDestIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Clears all static routes with the specified destination IP address." ::= { ipStaticRouteCfg 4} ipStaticRouteClearAllByGatewayIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Clears all static routes with the specified gateway IP address." ::= { ipStaticRouteCfg 5} ipStaticRouteClearAllByInterface OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Clears all routes on the specified inteface number." ::= { ipStaticRouteCfg 6} ipStaticRouteClearAll OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to clear(2),clears all static routes. Otherwhise nothing is done." ::= { ipStaticRouteCfg 7} ipStaticRouteCurPingInterval OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The time between ping retries." ::= { ipStaticRouteCfg 8} ipStaticRouteNewPingInterval OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The time between ping retries." ::= { ipStaticRouteCfg 9} ipStaticRouteCurPingRetries OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ping retries." ::= { ipStaticRouteCfg 10} ipStaticRouteNewPingRetries OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The number of ping retries." ::= { ipStaticRouteCfg 11} ipStaticRouteCurEcmpHash OBJECT-TYPE SYNTAX INTEGER { dipsip(0), sip(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Ecmp Hash based on dipsip/sip." ::= { ipStaticRouteCfg 12} ipStaticRouteNewEcmpHash OBJECT-TYPE SYNTAX INTEGER { dipsip(0), sip(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Ecmp Hash based on dipsip/sip." ::= { ipStaticRouteCfg 13} ipStaticRouteCurHealthcheck OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Gateway healthcheck functionality" ::= { ipStaticRouteCfg 16} ipStaticRouteNewHealthcheck OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Gateway healthcheck functionality" ::= { ipStaticRouteCfg 17} ipNewCfgStaticRouteEntry OBJECT-TYPE SYNTAX IpNewCfgStaticRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static IP route table" INDEX { ipNewCfgStaticRouteIndx } ::= { ipNewCfgStaticRouteTable 1 } IpNewCfgStaticRouteEntry ::= SEQUENCE { ipNewCfgStaticRouteIndx Integer32, ipNewCfgStaticRouteDestIp IpAddress, ipNewCfgStaticRouteMask IpAddress, ipNewCfgStaticRouteGateway IpAddress, ipNewCfgStaticRouteAction INTEGER, ipNewCfgStaticRouteInterface Integer32 } ipNewCfgStaticRouteIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the static routing table." ::= { ipNewCfgStaticRouteEntry 1} ipNewCfgStaticRouteDestIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The destination IP address of this route." ::= { ipNewCfgStaticRouteEntry 2} ipNewCfgStaticRouteMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The subnet mask of this route." ::= { ipNewCfgStaticRouteEntry 3} ipNewCfgStaticRouteGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of the gateway for this route." ::= { ipNewCfgStaticRouteEntry 4} ipNewCfgStaticRouteAction OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ipNewCfgStaticRouteEntry 5 } ipNewCfgStaticRouteInterface OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The IP interface of this route. The IP address of the specified interface shall be use as source IP when performs routing." ::= { ipNewCfgStaticRouteEntry 6 } -- RIP version 2 Configuration ripCurCfgIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF RipCurCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of RIP on IP interface in the current configuration block." ::= { rip2Cfg 1 } ripCurCfgIntfEntry OBJECT-TYPE SYNTAX RipCurCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about RIP on IP interface." INDEX { ripCurCfgIntfIndex } ::= { ripCurCfgIntfTable 1 } RipCurCfgIntfEntry ::= SEQUENCE { ripCurCfgIntfIndex Integer32, ripCurCfgIntfVersion INTEGER, ripCurCfgIntfSupply INTEGER, ripCurCfgIntfListen INTEGER, ripCurCfgIntfTrigUpdate INTEGER, ripCurCfgIntfMcastUpdate INTEGER, ripCurCfgIntfPoisonReverse INTEGER, ripCurCfgIntfState INTEGER, ripCurCfgIntfMetric INTEGER, ripCurCfgIntfAuth INTEGER, ripCurCfgIntfKey DisplayString, ripCurCfgIntfDefault INTEGER, ripCurCfgIntfSplitHorizon INTEGER } ripCurCfgIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number for which the RIP information is related." ::= { ripCurCfgIntfEntry 1} ripCurCfgIntfVersion OBJECT-TYPE SYNTAX INTEGER { ripVersion1(1), ripVersion2(2), ripVersionBoth(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "RIP version." ::= { ripCurCfgIntfEntry 2 } ripCurCfgIntfState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable RIP protocol." ::= { ripCurCfgIntfEntry 3 } ripCurCfgIntfListen OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable listening to route updates." ::= { ripCurCfgIntfEntry 4 } ripCurCfgIntfTrigUpdate OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable triggered updates." ::= { ripCurCfgIntfEntry 6 } ripCurCfgIntfMcastUpdate OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable multicast updates." ::= { ripCurCfgIntfEntry 7 } ripCurCfgIntfPoisonReverse OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "RIP poison reverse." ::= { ripCurCfgIntfEntry 8 } ripCurCfgIntfSupply OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable supplying route updates." ::= { ripCurCfgIntfEntry 9 } ripCurCfgIntfMetric OBJECT-TYPE SYNTAX INTEGER (1..15) MAX-ACCESS read-only STATUS current DESCRIPTION "RIP route metric for this interface." ::= { ripCurCfgIntfEntry 10 } ripCurCfgIntfAuth OBJECT-TYPE SYNTAX INTEGER { none(1), password(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of Authentication used on this interface." ::= { ripCurCfgIntfEntry 11 } ripCurCfgIntfKey OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "RIP update authentication password." ::= { ripCurCfgIntfEntry 12 } ripCurCfgIntfDefault OBJECT-TYPE SYNTAX INTEGER { both(1), listen(2), supply(3), none(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies what RIP does with default routes." ::= { ripCurCfgIntfEntry 13 } ripCurCfgIntfSplitHorizon OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "RIP split horizon." ::= {ripCurCfgIntfEntry 14 } ripNewCfgIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF RipNewCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of RIP on IP interface in the new configuration block." ::= { rip2Cfg 2 } ripNewCfgIntfEntry OBJECT-TYPE SYNTAX RipNewCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about RIP on IP interface." INDEX { ripNewCfgIntfIndex } ::= { ripNewCfgIntfTable 1 } RipNewCfgIntfEntry ::= SEQUENCE { ripNewCfgIntfIndex Integer32, ripNewCfgIntfVersion INTEGER, ripNewCfgIntfSupply INTEGER, ripNewCfgIntfListen INTEGER, ripNewCfgIntfTrigUpdate INTEGER, ripNewCfgIntfMcastUpdate INTEGER, ripNewCfgIntfPoisonReverse INTEGER, ripNewCfgIntfState INTEGER, ripNewCfgIntfMetric INTEGER, ripNewCfgIntfAuth INTEGER, ripNewCfgIntfKey DisplayString, ripNewCfgIntfDefault INTEGER, ripNewCfgIntfSplitHorizon INTEGER } ripNewCfgIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number for which the RIP information is related." ::= { ripNewCfgIntfEntry 1} ripNewCfgIntfVersion OBJECT-TYPE SYNTAX INTEGER { ripVersion1(1), ripVersion2(2), ripVersionBoth(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "RIP version." ::= { ripNewCfgIntfEntry 2 } ripNewCfgIntfSupply OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable supplying route updates." ::= { ripNewCfgIntfEntry 3 } ripNewCfgIntfListen OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable listening to route updates." ::= { ripNewCfgIntfEntry 4 } ripNewCfgIntfTrigUpdate OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable triggered updates." ::= { ripNewCfgIntfEntry 6 } ripNewCfgIntfMcastUpdate OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable multicast updates." ::= { ripNewCfgIntfEntry 7 } ripNewCfgIntfPoisonReverse OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "RIP poison reverse." ::= { ripNewCfgIntfEntry 8 } ripNewCfgIntfState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable RIP protocol." ::= { ripNewCfgIntfEntry 9 } ripNewCfgIntfMetric OBJECT-TYPE SYNTAX INTEGER (1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "RIP route metric for this interface." ::= { ripNewCfgIntfEntry 10 } ripNewCfgIntfAuth OBJECT-TYPE SYNTAX INTEGER { none(1), password(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Authentication used on this interface." ::= { ripNewCfgIntfEntry 11 } ripNewCfgIntfKey OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "RIP update authentication password." ::= { ripNewCfgIntfEntry 12 } ripNewCfgIntfDefault OBJECT-TYPE SYNTAX INTEGER { both(1), listen(2), supply(3), none(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies what RIP does with default routes. The default routes action could be set to listen/supply/both/none." ::= { ripNewCfgIntfEntry 13 } ripNewCfgIntfSplitHorizon OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "RIP split horizon." ::= { ripNewCfgIntfEntry 14 } ripGeneral OBJECT IDENTIFIER ::= { rip2Cfg 3 } rip2CurCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "RIP global state." ::= { ripGeneral 1 } rip2NewCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Globally turn RIP on or off." ::= { ripGeneral 2 } rip2CurCfgUpdatePeriod OBJECT-TYPE SYNTAX INTEGER (1..120) MAX-ACCESS read-only STATUS current DESCRIPTION "Update Period in seconds." ::= { ripGeneral 3 } rip2NewCfgUpdatePeriod OBJECT-TYPE SYNTAX INTEGER (1..120) MAX-ACCESS read-write STATUS current DESCRIPTION "Update Period in seconds." ::= { ripGeneral 4 } ripRouteRedistribution OBJECT IDENTIFIER ::= { rip2Cfg 4 } ripRedistributeStatic OBJECT IDENTIFIER ::= { ripRouteRedistribution 1 } ripCurCfgStaticMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The metric to be assigned to static routes. A value of 0 indicates none." ::= { ripRedistributeStatic 1 } ripNewCfgStaticMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The metric to be assigned to static routes. A value of 0 indicates none." ::= { ripRedistributeStatic 2 } ripCurCfgStaticOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeStatic 5 } ripNewCfgStaticOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeStatic 6 } ripNewCfgStaticAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ripRedistributeStatic 7 } ripNewCfgStaticRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ripRedistributeStatic 8 } ripRedistributeEbgp OBJECT IDENTIFIER ::= { ripRouteRedistribution 2 } ripCurCfgEbgpMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The export metric to be assigned to External BGP routes. A value of 0 indicates none." ::= { ripRedistributeEbgp 1 } ripNewCfgEbgpMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The export metric to be assigned to External BGP routes. A value of 0 indicates none." ::= { ripRedistributeEbgp 2 } ripCurCfgEbgpOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeEbgp 5 } ripNewCfgEbgpOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeEbgp 6 } ripNewCfgEbgpAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ripRedistributeEbgp 7 } ripNewCfgEbgpRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ripRedistributeEbgp 8 } ripRedistributeIbgp OBJECT IDENTIFIER ::= { ripRouteRedistribution 3 } ripCurCfgIbgpMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The export metric for Internal BGP routes. A value of 0 indicates none." ::= { ripRedistributeIbgp 1 } ripNewCfgIbgpMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The export metric for Internal BGP routes. A value of 0 indicates none." ::= { ripRedistributeIbgp 2 } ripCurCfgIbgpOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeIbgp 5 } ripNewCfgIbgpOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeIbgp 6 } ripNewCfgIbgpAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ripRedistributeIbgp 7 } ripNewCfgIbgpRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ripRedistributeIbgp 8 } ripRedistributeFixed OBJECT IDENTIFIER ::= { ripRouteRedistribution 4 } ripCurCfgFixedMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The export metric for fixed routes. A value of 0 indicates none" ::= { ripRedistributeFixed 1 } ripNewCfgFixedMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The export metric for fixed routes. A value of 0 indicates none" ::= { ripRedistributeFixed 2 } ripCurCfgFixedOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeFixed 5 } ripNewCfgFixedOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeFixed 6 } ripNewCfgFixedAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ripRedistributeFixed 7 } ripNewCfgFixedRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ripRedistributeFixed 8 } ripRedistributeOspf OBJECT IDENTIFIER ::= { ripRouteRedistribution 5 } ripCurCfgOspfMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The export metric for RIP routes. A value of 0 indicates none" ::= { ripRedistributeOspf 1 } ripNewCfgOspfMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The export metric for RIP routes. A value of 0 indicates none" ::= { ripRedistributeOspf 2 } ripCurCfgOspfOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeOspf 5 } ripNewCfgOspfOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeOspf 6 } ripNewCfgOspfAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ripRedistributeOspf 7 } ripNewCfgOspfRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ripRedistributeOspf 8 } ripRedistributeEospf OBJECT IDENTIFIER ::= { ripRouteRedistribution 6 } ripCurCfgEospfMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The export metric for RIP routes. A value of 0 indicates none" ::= { ripRedistributeEospf 1 } ripNewCfgEospfMetric OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The export metric for RIP routes. A value of 0 indicates none" ::= { ripRedistributeEospf 2 } ripCurCfgEospfOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeEospf 5 } ripNewCfgEospfOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ripRedistributeEospf 6 } ripNewCfgEospfAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ripRedistributeEospf 7 } ripNewCfgEospfRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ripRedistributeEospf 8 } -- IP Forwarding Configuration ipFwdGeneralCfg OBJECT IDENTIFIER ::= {ipForwardCfg 1 } ipFwdCurCfgState OBJECT-TYPE SYNTAX INTEGER { on(2), off(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "IP forwarding global state." ::= { ipFwdGeneralCfg 1 } ipFwdNewCfgState OBJECT-TYPE SYNTAX INTEGER { on(2), off(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "IP forwarding global state." ::= { ipFwdGeneralCfg 2 } ipFwdCurCfgDirectedBcast OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable forwarding directed broadcasts." ::= { ipFwdGeneralCfg 3 } ipFwdNewCfgDirectedBcast OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable forwarding directed broadcasts." ::= { ipFwdGeneralCfg 4 } ipFwdCurCfgNoICMPRedirect OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable no icmp redirects." ::= { ipFwdGeneralCfg 5 } ipFwdNewCfgNoICMPRedirect OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable no icmp redirects." ::= { ipFwdGeneralCfg 6 } ipFwdCurCfgICMP6Redirect OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable ICMPv6 redirects." ::= { ipFwdGeneralCfg 7 } ipFwdNewCfgICMP6Redirect OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable ICMPv6 redirects." ::= { ipFwdGeneralCfg 8 } -- -- ARP configuration -- arpCurCfgReARPPeriod OBJECT-TYPE SYNTAX INTEGER (2..120) MAX-ACCESS read-only STATUS current DESCRIPTION "Re-ARP Period in seconds." ::= { arpCfg 1 } arpNewCfgReARPPeriod OBJECT-TYPE SYNTAX INTEGER (2..120) MAX-ACCESS read-write STATUS current DESCRIPTION "Re-ARP Period in seconds." ::= { arpCfg 2 } -- -- IP Bootp Configration -- ipCurCfgBootpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of BOOTP server." ::= { ipBootpCfg 1 } ipNewCfgBootpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of BOOTP server." ::= { ipBootpCfg 2 } ipCurCfgBootpAddr2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of second BOOTP server." ::= { ipBootpCfg 3 } ipNewCfgBootpAddr2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of second BOOTP server." ::= { ipBootpCfg 4 } ipCurCfgBootpState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of BOOTP relay." ::= { ipBootpCfg 5 } ipNewCfgBootpState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The state of BOOTP relay." ::= { ipBootpCfg 6 } ipCurCfgBootpGlobalServerTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgBootpGlobalServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of global BOOTP server addresses" ::= { ipBootpCfg 20 } ipCurCfgBootpGlobalServerEntry OBJECT-TYPE SYNTAX IpCurCfgBootpGlobalServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the ipCurCfgBootpGlobalServerAddrTable" INDEX { ipCurCfgBootpGlobalServerIndex } ::= { ipCurCfgBootpGlobalServerTable 1 } IpCurCfgBootpGlobalServerEntry ::= SEQUENCE { ipCurCfgBootpGlobalServerIndex Integer32, ipCurCfgBootpGlobalServerAddress IpAddress } ipCurCfgBootpGlobalServerIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipCurCfgBootpGlobalServerTable" ::= { ipCurCfgBootpGlobalServerEntry 1 } ipCurCfgBootpGlobalServerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The current global server IP." ::= { ipCurCfgBootpGlobalServerEntry 2 } ipNewCfgBootpGlobalServerTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgBootpGlobalServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of global BOOTP server addresses" ::= { ipBootpCfg 21 } ipNewCfgBootpGlobalServerEntry OBJECT-TYPE SYNTAX IpNewCfgBootpGlobalServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the ipNewCfgBootpGlobalServerAddrTable" INDEX { ipNewCfgBootpGlobalServerIndex } ::= { ipNewCfgBootpGlobalServerTable 1 } IpNewCfgBootpGlobalServerEntry ::= SEQUENCE { ipNewCfgBootpGlobalServerIndex Integer32, ipNewCfgBootpGlobalServerAddress IpAddress } ipNewCfgBootpGlobalServerIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipCurCfgBootpGlobalServerTable" ::= { ipNewCfgBootpGlobalServerEntry 1 } ipNewCfgBootpGlobalServerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The current global server IP." ::= { ipNewCfgBootpGlobalServerEntry 2 } ipCurCfgBootpBcastDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgBootpBcastDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of broadcast domain settings" ::= { ipBootpCfg 22 } ipCurCfgBootpBcastDomainEntry OBJECT-TYPE SYNTAX IpCurCfgBootpBcastDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the broadcast domain table" INDEX { ipCurCfgBootpBcastDomainIndex } ::= { ipCurCfgBootpBcastDomainTable 1 } IpCurCfgBootpBcastDomainEntry ::= SEQUENCE { ipCurCfgBootpBcastDomainIndex Integer32, ipCurCfgBootpBcastDomainVlan Integer32, ipCurCfgBootpBcastDomainEnable INTEGER } ipCurCfgBootpBcastDomainIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the broadcast domain entry" ::= { ipCurCfgBootpBcastDomainEntry 1 } ipCurCfgBootpBcastDomainVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN of the broadcast domain entry" ::= { ipCurCfgBootpBcastDomainEntry 2 } ipCurCfgBootpBcastDomainEnable OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the broadcast domain entry" ::= { ipCurCfgBootpBcastDomainEntry 3 } ipNewCfgBootpBcastDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgBootpBcastDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of broadcast domain settings" ::= { ipBootpCfg 23 } ipNewCfgBootpBcastDomainEntry OBJECT-TYPE SYNTAX IpNewCfgBootpBcastDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the broadcast domain table" INDEX { ipNewCfgBootpBcastDomainIndex } ::= { ipNewCfgBootpBcastDomainTable 1 } IpNewCfgBootpBcastDomainEntry ::= SEQUENCE { ipNewCfgBootpBcastDomainIndex Integer32, ipNewCfgBootpBcastDomainVlan Integer32, ipNewCfgBootpBcastDomainEnable INTEGER, ipNewCfgBootpBcastDomainAction INTEGER } ipNewCfgBootpBcastDomainIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the broadcast domain entry" ::= { ipNewCfgBootpBcastDomainEntry 1 } ipNewCfgBootpBcastDomainVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN of the broadcast domain entry" ::= { ipNewCfgBootpBcastDomainEntry 2 } ipNewCfgBootpBcastDomainEnable OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The state of the broadcast domain entry" ::= { ipNewCfgBootpBcastDomainEntry 3 } ipNewCfgBootpBcastDomainAction OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the broadcast domain is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect on the state of broadcast domain." ::= { ipNewCfgBootpBcastDomainEntry 4 } ipCurCfgBootpBcastDomainServerTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgBootpBcastDomainServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of broadcast domain servers" ::= { ipBootpCfg 24 } ipCurCfgBootpBcastDomainServerEntry OBJECT-TYPE SYNTAX IpCurCfgBootpBcastDomainServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the broadcast domain server table" INDEX { ipCurCfgBootpBcastDomainBDIndex, ipCurCfgBootpBcastDomainServIndex } ::= { ipCurCfgBootpBcastDomainServerTable 1 } IpCurCfgBootpBcastDomainServerEntry ::= SEQUENCE { ipCurCfgBootpBcastDomainBDIndex Integer32, ipCurCfgBootpBcastDomainServIndex Integer32, ipCurCfgBootpBcastDomainServerIP IpAddress } ipCurCfgBootpBcastDomainBDIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the broadcast domain entry in the server table" ::= { ipCurCfgBootpBcastDomainServerEntry 1 } ipCurCfgBootpBcastDomainServIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the server in the server table" ::= { ipCurCfgBootpBcastDomainServerEntry 2 } ipCurCfgBootpBcastDomainServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The current broadcast domain server IP." ::= { ipCurCfgBootpBcastDomainServerEntry 3 } ipNewCfgBootpBcastDomainServerTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgBootpBcastDomainServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of broadcast domain servers" ::= { ipBootpCfg 25 } ipNewCfgBootpBcastDomainServerEntry OBJECT-TYPE SYNTAX IpNewCfgBootpBcastDomainServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the broadcast domain server table" INDEX { ipNewCfgBootpBcastDomainBDIndex, ipNewCfgBootpBcastDomainServIndex } ::= { ipNewCfgBootpBcastDomainServerTable 1 } IpNewCfgBootpBcastDomainServerEntry ::= SEQUENCE { ipNewCfgBootpBcastDomainBDIndex Integer32, ipNewCfgBootpBcastDomainServIndex Integer32, ipNewCfgBootpBcastDomainServerIP IpAddress } ipNewCfgBootpBcastDomainBDIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the broadcast domain entry in the server table" ::= { ipNewCfgBootpBcastDomainServerEntry 1 } ipNewCfgBootpBcastDomainServIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the server in the server table" ::= { ipNewCfgBootpBcastDomainServerEntry 2 } ipNewCfgBootpBcastDomainServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The current broadcast domain server IP." ::= { ipNewCfgBootpBcastDomainServerEntry 3 } ipCurCfgBootpOpt82State OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of Bootp relay option 82" ::= { ipBootpCfg 26 } ipNewCfgBootpOpt82State OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set the stare of Bootp relay option 82" ::= { ipBootpCfg 27 } ipCurCfgBootpOpt82Policy OBJECT-TYPE SYNTAX INTEGER { replace(0), drop(1), keep(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The policy of Bootp relay option 82" ::= { ipBootpCfg 28 } ipNewCfgBootpOpt82Policy OBJECT-TYPE SYNTAX INTEGER { replace(0), drop(1), keep(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set the policy of Bootp relay option 82" ::= { ipBootpCfg 29 } -- VRRP (Virtual Router Redundantcy Protocol) Group vrrpGeneral OBJECT IDENTIFIER ::= { vrrpCfg 1 } vrrpCurCfgGenState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable VRRP operation globally." ::= { vrrpGeneral 1 } vrrpNewCfgGenState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable VRRP operation globally." ::= { vrrpGeneral 2 } vrrpCurCfgGenTckVirtRtrInc OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-only STATUS current DESCRIPTION "The increment of VRRP virtual router priority. The priority is adjusted by tracking the state of other virtual routers." ::= { vrrpGeneral 3 } vrrpNewCfgGenTckVirtRtrInc OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-write STATUS current DESCRIPTION "The increment of VRRP virtual router priority. The priority is adjusted by tracking the state of other virtual routers." ::= { vrrpGeneral 4 } vrrpCurCfgGenTckIpIntfInc OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-only STATUS current DESCRIPTION "The increment of VRRP virtual router priority. The priority is adjusted by tracking the state of other router interfaces." ::= { vrrpGeneral 5 } vrrpNewCfgGenTckIpIntfInc OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-write STATUS current DESCRIPTION "The increment of VRRP virtual router priority. The priority is adjusted by tracking the state of other router interfaces." ::= { vrrpGeneral 6 } vrrpCurCfgGenTckVlanPortInc OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-only STATUS current DESCRIPTION "The increment of VRRP virtual router priority. The priority is adjusted by tracking the port state of ports that belongs to the same virtual LAN as the virtual router." ::= { vrrpGeneral 7 } vrrpNewCfgGenTckVlanPortInc OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-write STATUS current DESCRIPTION "The increment of VRRP virtual router priority. The priority is adjusted by tracking the port state of ports that belongs to the same virtual LAN as the virtual router." ::= { vrrpGeneral 8 } vrrpCurCfgGenHoldoff OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The time for VRRP virtual router to hold before it begins to change state to backup or master state." ::= { vrrpGeneral 19 } vrrpNewCfgGenHoldoff OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The time for VRRP virtual router to hold before it begins to change state to backup or master state." ::= { vrrpGeneral 20 } vrrpVirtRtrTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in VRRP virtual router table." ::= { vrrpCfg 2 } vrrpCurCfgVirtRtrTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpCurCfgVirtRtrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VRRP virtual routers in the current configuration block." ::= { vrrpCfg 3 } vrrpCurCfgVirtRtrTableEntry OBJECT-TYPE SYNTAX VrrpCurCfgVirtRtrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a VRRP virtual router." INDEX { vrrpCurCfgVirtRtrIndx } ::= { vrrpCurCfgVirtRtrTable 1 } VrrpCurCfgVirtRtrTableEntry ::= SEQUENCE { vrrpCurCfgVirtRtrIndx Integer32, vrrpCurCfgVirtRtrID INTEGER, vrrpCurCfgVirtRtrAddr IpAddress, vrrpCurCfgVirtRtrIfIndex Integer32, vrrpCurCfgVirtRtrInterval INTEGER, vrrpCurCfgVirtRtrPreDelay INTEGER, vrrpCurCfgVirtRtrPriority INTEGER, vrrpCurCfgVirtRtrPreempt INTEGER, vrrpCurCfgVirtRtrTckVirtRtr INTEGER, vrrpCurCfgVirtRtrTckIpIntf INTEGER, vrrpCurCfgVirtRtrTckVlanPort INTEGER, vrrpCurCfgVirtRtrState INTEGER , vrrpCurCfgVirtRtrFastAdvertisement INTEGER } vrrpCurCfgVirtRtrIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router table index." ::= { vrrpCurCfgVirtRtrTableEntry 1 } vrrpCurCfgVirtRtrID OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router identifier." ::= { vrrpCurCfgVirtRtrTableEntry 2 } vrrpCurCfgVirtRtrAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router IP address." ::= { vrrpCurCfgVirtRtrTableEntry 3 } vrrpCurCfgVirtRtrIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The IfIndex that the VRRP virtual router is representing." ::= { vrrpCurCfgVirtRtrTableEntry 4 } vrrpCurCfgVirtRtrInterval OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The time interval between VRRP advertisements in seconds. When FAST_ADVERTISEMENT is enabled, this object indicates advertisement interval in centi-seconds" ::= { vrrpCurCfgVirtRtrTableEntry 5 } vrrpCurCfgVirtRtrPriority OBJECT-TYPE SYNTAX INTEGER (1..254) MAX-ACCESS read-only STATUS current DESCRIPTION "The priority value to be used by the specified VRRP virtual routers." ::= { vrrpCurCfgVirtRtrTableEntry 6 } vrrpCurCfgVirtRtrPreempt OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is for controlling whether a higher priority Backup VRRP virtual router preempts a low priority Master. enabled(1) - allow preemption disabled(2) - prohibit preemption" ::= { vrrpCurCfgVirtRtrTableEntry 7 } vrrpCurCfgVirtRtrTckVirtRtr OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable tracking other virtual routers for priority adjustment. The priority increment is defined in vrrpCurCfgGenTckVirtRtrInc." ::= { vrrpCurCfgVirtRtrTableEntry 9 } vrrpCurCfgVirtRtrTckIpIntf OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable tracking other router interfaces for priority adjustment. The priority increment is defined in vrrpCurCfgGenTckIpIntfInc." ::= { vrrpCurCfgVirtRtrTableEntry 10 } vrrpCurCfgVirtRtrTckVlanPort OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable tracking port state of VLAN ports for priority adjustment. The priority increment is defined in vrrpCurCfgGenTckVlanPortInc." ::= { vrrpCurCfgVirtRtrTableEntry 15 } vrrpCurCfgVirtRtrState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the VRRP virtual router." ::= { vrrpCurCfgVirtRtrTableEntry 16 } vrrpCurCfgVirtRtrFastAdvertisement OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the status of FAST_ADVERTISEMENT. When FAST_ADVERTISEMENT is enabled, - New message type FAST-ADVERTISEMENT(2) will be used in the VRRP advertisements - Can interop only with another FAST_ADVERTISEMENT enabled router - VRRP advertisement interval will be sent in units of centi-seconds - Timers will be running with centi-second granularity" ::= { vrrpCurCfgVirtRtrTableEntry 17 } vrrpCurCfgVirtRtrPreDelay OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The pre-emptive delay interval in seconds." ::= { vrrpCurCfgVirtRtrTableEntry 18 } vrrpNewCfgVirtRtrTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpNewCfgVirtRtrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VRRP virtual routers in the current configuration block." ::= { vrrpCfg 4 } vrrpNewCfgVirtRtrTableEntry OBJECT-TYPE SYNTAX VrrpNewCfgVirtRtrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a VRRP virtual router." INDEX { vrrpNewCfgVirtRtrIndx } ::= { vrrpNewCfgVirtRtrTable 1 } VrrpNewCfgVirtRtrTableEntry ::= SEQUENCE { vrrpNewCfgVirtRtrIndx Integer32, vrrpNewCfgVirtRtrID INTEGER, vrrpNewCfgVirtRtrAddr IpAddress, vrrpNewCfgVirtRtrIfIndex Integer32, vrrpNewCfgVirtRtrInterval INTEGER, vrrpNewCfgVirtRtrPreDelay INTEGER, vrrpNewCfgVirtRtrPriority INTEGER, vrrpNewCfgVirtRtrPreempt INTEGER, vrrpNewCfgVirtRtrDelete INTEGER, vrrpNewCfgVirtRtrTckVirtRtr INTEGER, vrrpNewCfgVirtRtrTckIpIntf INTEGER, vrrpNewCfgVirtRtrTckVlanPort INTEGER, vrrpNewCfgVirtRtrState INTEGER , vrrpNewCfgVirtRtrFastAdvertisement INTEGER } vrrpNewCfgVirtRtrIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router table index." ::= { vrrpNewCfgVirtRtrTableEntry 1 } vrrpNewCfgVirtRtrID OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The VRRP virtual router identifier." ::= { vrrpNewCfgVirtRtrTableEntry 2 } vrrpNewCfgVirtRtrAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The VRRP virtual router IP address." ::= { vrrpNewCfgVirtRtrTableEntry 3 } vrrpNewCfgVirtRtrIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The IfIndex that the VRRP virtual router is representing." ::= { vrrpNewCfgVirtRtrTableEntry 4 } vrrpNewCfgVirtRtrInterval OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The time interval between VRRP advertisements in seconds. When FAST_ADVERTISEMENT is enabled, this object indicates advertisement interval in centi-seconds" ::= { vrrpNewCfgVirtRtrTableEntry 5 } vrrpNewCfgVirtRtrPriority OBJECT-TYPE SYNTAX INTEGER (1..254) MAX-ACCESS read-create STATUS current DESCRIPTION "The priority value to be used by the specified VRRP virtual router." ::= { vrrpNewCfgVirtRtrTableEntry 6 } vrrpNewCfgVirtRtrPreempt OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This is for controlling whether a higher priority Backup VRRP virtual router preempts a low priority Master. enabled(1) - allow preemption disabled(2) - prohibit preemption" ::= { vrrpNewCfgVirtRtrTableEntry 7 } vrrpNewCfgVirtRtrDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than delete(2) has no effect on the state of the row." ::= { vrrpNewCfgVirtRtrTableEntry 8 } vrrpNewCfgVirtRtrTckVirtRtr OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable tracking other virtual routers for priority adjustment. the priority increment is defined in vrrpNewCfgGenTckVirtRtrInc." ::= { vrrpNewCfgVirtRtrTableEntry 10 } vrrpNewCfgVirtRtrTckIpIntf OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable tracking other router interfaces for priority adjustment. the priority increment is defined in vrrpNewCfgGenTckIpIntfInc." ::= { vrrpNewCfgVirtRtrTableEntry 11 } vrrpNewCfgVirtRtrTckVlanPort OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable tracking port state of VLAN ports for priority adjustment. the priority increment is defined in vrrpNewCfgGenTckVlanPortInc." ::= { vrrpNewCfgVirtRtrTableEntry 12 } vrrpNewCfgVirtRtrState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable the VRRP virtual router." ::= { vrrpNewCfgVirtRtrTableEntry 17 } vrrpNewCfgVirtRtrFastAdvertisement OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object can be enabled if sub-second advertisement interval is required. When FAST_ADVERTISEMENT is enabled, - New message type FAST-ADVERTISEMENT(2) will be used in the VRRP advertisements - Can interop only with another FAST_ADVERTISEMENT enabled router - VRRP advertisement interval will be sent in units of centi-seconds - Timers will be running with centi-second granularity" DEFVAL { disabled } ::= { vrrpNewCfgVirtRtrTableEntry 18 } vrrpNewCfgVirtRtrPreDelay OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The pre-emptive delay interval in seconds." ::= { vrrpNewCfgVirtRtrTableEntry 19 } -- VRRP Interface Table vrrpIfTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in VRRP interface table." ::= { vrrpCfg 5 } vrrpCurCfgIfTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpCurCfgIfTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VRRP interface in the current configuration block." ::= { vrrpCfg 6 } vrrpCurCfgIfTableEntry OBJECT-TYPE SYNTAX VrrpCurCfgIfTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a VRRP interface." INDEX { vrrpCurCfgIfIndx } ::= { vrrpCurCfgIfTable 1 } VrrpCurCfgIfTableEntry ::= SEQUENCE { vrrpCurCfgIfIndx Integer32, vrrpCurCfgIfAuthType INTEGER, vrrpCurCfgIfPasswd DisplayString } vrrpCurCfgIfIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP interface index. This is eqivalent to IfIndex." ::= { vrrpCurCfgIfTableEntry 1 } vrrpCurCfgIfAuthType OBJECT-TYPE SYNTAX INTEGER { none(1), simple-text-password(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of authentication being used. none(1) - no authentication simple-text-password(2) - use password specified in vrrpCurCfgIfPasswd for authentication." ::= { vrrpCurCfgIfTableEntry 2 } vrrpCurCfgIfPasswd OBJECT-TYPE SYNTAX DisplayString (SIZE(0..7)) MAX-ACCESS read-only STATUS current DESCRIPTION "The password for authentication." ::= { vrrpCurCfgIfTableEntry 3 } vrrpNewCfgIfTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpNewCfgIfTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VRRP interface in the current configuration block." ::= { vrrpCfg 7 } vrrpNewCfgIfTableEntry OBJECT-TYPE SYNTAX VrrpNewCfgIfTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a VRRP interface." INDEX { vrrpNewCfgIfIndx } ::= { vrrpNewCfgIfTable 1 } VrrpNewCfgIfTableEntry ::= SEQUENCE { vrrpNewCfgIfIndx Integer32, vrrpNewCfgIfAuthType INTEGER, vrrpNewCfgIfPasswd DisplayString, vrrpNewCfgIfDelete INTEGER } vrrpNewCfgIfIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP interface index. This is eqivalent to IfIndex." ::= { vrrpNewCfgIfTableEntry 1 } vrrpNewCfgIfAuthType OBJECT-TYPE SYNTAX INTEGER { none(1), simple-text-password(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Type of authentication being used. none(1) - no authentication simple-text-password(2) - use password specified in vrrpNewCfgIfPasswd for authentication." ::= { vrrpNewCfgIfTableEntry 2 } vrrpNewCfgIfPasswd OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-create STATUS current DESCRIPTION "The password for authentication." ::= { vrrpNewCfgIfTableEntry 3 } vrrpNewCfgIfDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than delete(2) has no effect on the state of the row." ::= { vrrpNewCfgIfTableEntry 4 } -- Failover Virtual Router Groups vrrpVirtRtrGrpTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in VRRP Group table." ::= { vrrpCfg 8 } vrrpCurCfgVirtRtrGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpCurCfgVirtRtrGrpTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VRRP virtual router group in the current configuration block." ::= { vrrpCfg 9 } vrrpCurCfgVirtRtrGrpTableEntry OBJECT-TYPE SYNTAX VrrpCurCfgVirtRtrGrpTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a VRRP failover virtual router." INDEX { vrrpCurCfgVirtRtrGrpIndx } ::= { vrrpCurCfgVirtRtrGrpTable 1 } VrrpCurCfgVirtRtrGrpTableEntry ::= SEQUENCE { vrrpCurCfgVirtRtrGrpIndx Integer32, vrrpCurCfgVirtRtrGrpID INTEGER, vrrpCurCfgVirtRtrGrpIfIndex Integer32, vrrpCurCfgVirtRtrGrpInterval INTEGER, vrrpCurCfgVirtRtrGrpPriority INTEGER, vrrpCurCfgVirtRtrGrpPreempt INTEGER, vrrpCurCfgVirtRtrGrpState INTEGER, vrrpCurCfgVirtRtrGrpTckIpIntf INTEGER, vrrpCurCfgVirtRtrGrpTckVlanPort INTEGER ,vrrpCurCfgVirtRtrGrpFastAdvertisement INTEGER ,vrrpCurCfgVirtRtrGrpPredelay INTEGER } vrrpCurCfgVirtRtrGrpIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router table index." ::= { vrrpCurCfgVirtRtrGrpTableEntry 1 } vrrpCurCfgVirtRtrGrpID OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router identifier." ::= { vrrpCurCfgVirtRtrGrpTableEntry 2 } vrrpCurCfgVirtRtrGrpIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The IfIndex that the VRRP virtual router is representing." ::= { vrrpCurCfgVirtRtrGrpTableEntry 3 } vrrpCurCfgVirtRtrGrpInterval OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The time interval between VRRP advertisements in seconds." ::= { vrrpCurCfgVirtRtrGrpTableEntry 4 } vrrpCurCfgVirtRtrGrpPriority OBJECT-TYPE SYNTAX INTEGER (1..254) MAX-ACCESS read-only STATUS current DESCRIPTION "The priority value to be used by the specified VRRP virtual routers." ::= { vrrpCurCfgVirtRtrGrpTableEntry 5 } vrrpCurCfgVirtRtrGrpPreempt OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is for controlling whether a higher priority Backup VRRP virtual router preempts a low priority Master. enabled(1) - allow preemption disabled(2) - prohibit preemption" ::= { vrrpCurCfgVirtRtrGrpTableEntry 6 } vrrpCurCfgVirtRtrGrpState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the VRRP virtual router." ::= { vrrpCurCfgVirtRtrGrpTableEntry 7 } vrrpCurCfgVirtRtrGrpTckIpIntf OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable tracking other router interfaces for priority adjustment. the priority increment is defined in vrrpCurCfgGenTckIpIntfInc." ::= { vrrpCurCfgVirtRtrGrpTableEntry 10 } vrrpCurCfgVirtRtrGrpTckVlanPort OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable tracking port state of VLAN ports for priority adjustment. the priority increment is defined in vrrpCurCfgGenTckVlanPortInc." ::= { vrrpCurCfgVirtRtrGrpTableEntry 11 } vrrpCurCfgVirtRtrGrpFastAdvertisement OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the status of FAST_ADVERTISEMENT. When FAST_ADVERTISEMENT is enabled, - New message type FAST-ADVERTISEMENT(2) will be used in the VRRP advertisements - Can interop only with another FAST_ADVERTISEMENT enabled router - VRRP advertisement interval will be sent in units of centi-seconds - Timers will be running with centi-second granularity" ::= { vrrpCurCfgVirtRtrGrpTableEntry 16 } vrrpCurCfgVirtRtrGrpPredelay OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The pre-emptive delay interval in seconds for specified VRRP virtual routers." ::= { vrrpCurCfgVirtRtrGrpTableEntry 21 } vrrpNewCfgVirtRtrGrpTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpNewCfgVirtRtrGrpTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VRRP virtual router group in the new configuration block." ::= { vrrpCfg 10 } vrrpNewCfgVirtRtrGrpTableEntry OBJECT-TYPE SYNTAX VrrpNewCfgVirtRtrGrpTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a VRRP failover virtual router." INDEX { vrrpNewCfgVirtRtrGrpIndx } ::= { vrrpNewCfgVirtRtrGrpTable 1 } VrrpNewCfgVirtRtrGrpTableEntry ::= SEQUENCE { vrrpNewCfgVirtRtrGrpIndx Integer32, vrrpNewCfgVirtRtrGrpID INTEGER, vrrpNewCfgVirtRtrGrpIfIndex Integer32, vrrpNewCfgVirtRtrGrpInterval INTEGER, vrrpNewCfgVirtRtrGrpPriority INTEGER, vrrpNewCfgVirtRtrGrpPreempt INTEGER, vrrpNewCfgVirtRtrGrpState INTEGER, vrrpNewCfgVirtRtrGrpDelete INTEGER, vrrpNewCfgVirtRtrGrpTckIpIntf INTEGER, vrrpNewCfgVirtRtrGrpTckVlanPort INTEGER ,vrrpNewCfgVirtRtrGrpFastAdvertisement INTEGER ,vrrpNewCfgVirtRtrGrpPredelay INTEGER } vrrpNewCfgVirtRtrGrpIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router table index." ::= { vrrpNewCfgVirtRtrGrpTableEntry 1 } vrrpNewCfgVirtRtrGrpID OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The VRRP virtual router identifier." ::= { vrrpNewCfgVirtRtrGrpTableEntry 2 } vrrpNewCfgVirtRtrGrpIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The IfIndex that the VRRP virtual router is representing." ::= { vrrpNewCfgVirtRtrGrpTableEntry 3 } vrrpNewCfgVirtRtrGrpInterval OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The time interval between VRRP advertisements in seconds." ::= { vrrpNewCfgVirtRtrGrpTableEntry 4 } vrrpNewCfgVirtRtrGrpPriority OBJECT-TYPE SYNTAX INTEGER (1..254) MAX-ACCESS read-create STATUS current DESCRIPTION "The priority value to be used by the specified VRRP virtual router." ::= { vrrpNewCfgVirtRtrGrpTableEntry 5 } vrrpNewCfgVirtRtrGrpPreempt OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This is for controlling whether a higher priority Backup VRRP virtual router preempts a low priority Master. enabled(1) - allow preemption disabled(2) - prohibit preemption" ::= { vrrpNewCfgVirtRtrGrpTableEntry 6 } vrrpNewCfgVirtRtrGrpState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable the VRRP virtual router." ::= { vrrpNewCfgVirtRtrGrpTableEntry 7 } vrrpNewCfgVirtRtrGrpDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than delete(2) has no effect on the state of the row." ::= { vrrpNewCfgVirtRtrGrpTableEntry 8 } vrrpNewCfgVirtRtrGrpTckIpIntf OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable tracking other router interfaces for priority adjustment. the priority increment is defined in vrrpNewCfgGenTckIpIntfInc." ::= { vrrpNewCfgVirtRtrGrpTableEntry 11 } vrrpNewCfgVirtRtrGrpTckVlanPort OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable tracking port state of VLAN ports for priority adjustment. the priority increment is defined in vrrpNewCfgGenTckVlanPortInc." ::= { vrrpNewCfgVirtRtrGrpTableEntry 12 } vrrpNewCfgVirtRtrGrpFastAdvertisement OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object can be enabled if sub-second advertisement interval is required. When FAST_ADVERTISEMENT is enabled, - New message type FAST-ADVERTISEMENT(2) will be used in the VRRP advertisements - Can interop only with another FAST_ADVERTISEMENT enabled router - VRRP advertisement interval will be sent in units of centi-seconds - Timers will be running with centi-second granularity" DEFVAL { disabled } ::= {vrrpNewCfgVirtRtrGrpTableEntry 17 } vrrpNewCfgVirtRtrGrpPredelay OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The pre-emptive delay interval in seconds." ::= { vrrpNewCfgVirtRtrGrpTableEntry 21 } -- Domain Name Server Configuration dnsCurCfgPrimaryIpAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The DNS primary IP address in the current configuration block." ::= { dnsCfg 1 } dnsNewCfgPrimaryIpAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The DNS primary IP address in the new configuration block." ::= { dnsCfg 2 } dnsCurCfgSecondaryIpAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The DNS primary IP address in the current configuration block." ::= { dnsCfg 3 } dnsNewCfgSecondaryIpAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The DNS primary IP address in the new configuration block." ::= { dnsCfg 4 } dnsCurCfgDomainName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..191)) MAX-ACCESS read-only STATUS current DESCRIPTION "The DNS doamin name in the current configuration block." ::= { dnsCfg 5 } dnsNewCfgDomainName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..191)) MAX-ACCESS read-write STATUS current DESCRIPTION "The DNS doamin name in the new configuration block." ::= { dnsCfg 6 } dnsNewCfgFirstRequestAddr OBJECT-TYPE SYNTAX INTEGER{ ipv4(1), ipv6(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of the first request to dns" ::= { dnsCfg 9 } dnsCurCfgFirstRequestAddr OBJECT-TYPE SYNTAX INTEGER{ ipv4(1), ipv6(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the first request to dns" ::= { dnsCfg 10} -- -- IP network filter configuration -- ipNwfTableMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the IP network filter table." ::= { ipNwfCfg 1 } ipCurCfgNwfTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgNwfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP network filter in the current configuration block." ::= { ipNwfCfg 2 } ipCurCfgNwfEntry OBJECT-TYPE SYNTAX IpCurCfgNwfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an IP network filter." INDEX { ipCurCfgNwfIndex } ::= { ipCurCfgNwfTable 1 } IpCurCfgNwfEntry ::= SEQUENCE { ipCurCfgNwfIndex Integer32, ipCurCfgNwfAddr IpAddress, ipCurCfgNwfMask IpAddress, ipCurCfgNwfState INTEGER } ipCurCfgNwfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The netowrk filter number for which the NWF is related." ::= { ipCurCfgNwfEntry 1} ipCurCfgNwfAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the network filter." ::= { ipCurCfgNwfEntry 2 } ipCurCfgNwfMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP network filter mask." ::= { ipCurCfgNwfEntry 3 } ipCurCfgNwfState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the network filter." ::= { ipCurCfgNwfEntry 4 } ipNewCfgNwfTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgNwfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP network filter in the current configuration block." ::= { ipNwfCfg 3 } ipNewCfgNwfEntry OBJECT-TYPE SYNTAX IpNewCfgNwfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an IP network filter." INDEX { ipNewCfgNwfIndex } ::= { ipNewCfgNwfTable 1 } IpNewCfgNwfEntry ::= SEQUENCE { ipNewCfgNwfIndex Integer32, ipNewCfgNwfAddr IpAddress, ipNewCfgNwfMask IpAddress, ipNewCfgNwfState INTEGER, ipNewCfgNwfDelete INTEGER } ipNewCfgNwfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The netowrk filter number for which the NWF is related." ::= { ipNewCfgNwfEntry 1} ipNewCfgNwfAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of the network filter." ::= { ipNewCfgNwfEntry 2 } ipNewCfgNwfMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP network filter mask." ::= { ipNewCfgNwfEntry 3 } ipNewCfgNwfState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable the network filter." ::= { ipNewCfgNwfEntry 4 } ipNewCfgNwfDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ipNewCfgNwfEntry 5 } -- -- IP route map configuration -- ipRmapTableMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the IP route map table." ::= { ipRmapCfg 1 } ipCurCfgRmapTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgRmapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP route map in the current configuration block." ::= { ipRmapCfg 2 } ipCurCfgRmapEntry OBJECT-TYPE SYNTAX IpCurCfgRmapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an IP route map." INDEX { ipCurCfgRmapIndex } ::= { ipCurCfgRmapTable 1 } IpCurCfgRmapEntry ::= SEQUENCE { ipCurCfgRmapIndex Integer32, ipCurCfgRmapLp Unsigned32, ipCurCfgRmapMetric Unsigned32, ipCurCfgRmapPrec INTEGER, ipCurCfgRmapWeight INTEGER, ipCurCfgRmapAp DisplayString, ipCurCfgRmapMetricType INTEGER, ipCurCfgRmapNexthop INTEGER, ipCurCfgRmapState INTEGER } ipCurCfgRmapIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The route map number for which the RMAP is related." ::= { ipCurCfgRmapEntry 1} ipCurCfgRmapLp OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The local-preference of the route map. 4294967295 means none" ::= { ipCurCfgRmapEntry 2 } ipCurCfgRmapMetric OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The metric of the route map. 4294967295 means none. Range is [1-16777214] if OSPF metric-type is used." ::= { ipCurCfgRmapEntry 3 } ipCurCfgRmapPrec OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The precedence of the route map." ::= { ipCurCfgRmapEntry 4 } ipCurCfgRmapWeight OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The weight of the route map. 65535 means none" ::= { ipCurCfgRmapEntry 5 } ipCurCfgRmapState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the route map." ::= { ipCurCfgRmapEntry 6 } ipCurCfgRmapAp OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The as-path prepend of the matched route. Up to 3 AS number can be displayed for the string. The usuage is: [][ ]" ::= { ipCurCfgRmapEntry 7 } ipCurCfgRmapMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF metric-type of the matched route." ::= { ipCurCfgRmapEntry 8 } ipCurCfgRmapNexthop OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Peer address as nexthop of the matched route(only for BGP)." ::= { ipCurCfgRmapEntry 9 } ipNewCfgRmapTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgRmapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP route map in the new configuration block." ::= { ipRmapCfg 3 } ipNewCfgRmapEntry OBJECT-TYPE SYNTAX IpNewCfgRmapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an IP route map." INDEX { ipNewCfgRmapIndex } ::= { ipNewCfgRmapTable 1 } IpNewCfgRmapEntry ::= SEQUENCE { ipNewCfgRmapIndex Integer32, ipNewCfgRmapLp Unsigned32, ipNewCfgRmapMetric Unsigned32, ipNewCfgRmapPrec INTEGER, ipNewCfgRmapWeight INTEGER, ipNewCfgRmapAp DisplayString, ipNewCfgRmapState INTEGER, ipNewCfgRmapMetricType INTEGER, ipNewCfgRmapNexthop INTEGER, ipNewCfgRmapDelete INTEGER } ipNewCfgRmapIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The route map number for which the RMAP is related." ::= { ipNewCfgRmapEntry 1} ipNewCfgRmapLp OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The local-preference of the route map. 4294967295 means none" ::= { ipNewCfgRmapEntry 2 } ipNewCfgRmapMetric OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The metric of the route map. 4294967295 means none. Range is [1-16777214] if OSPF metric-type is used." ::= { ipNewCfgRmapEntry 3 } ipNewCfgRmapPrec OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The precedence of the route map." ::= { ipNewCfgRmapEntry 4 } ipNewCfgRmapWeight OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The weight of the route map. 65535 means none" ::= { ipNewCfgRmapEntry 5 } ipNewCfgRmapState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable the route map." ::= { ipNewCfgRmapEntry 6 } ipNewCfgRmapAp OBJECT-TYPE SYNTAX DisplayString (SIZE(0..17)) MAX-ACCESS read-create STATUS current DESCRIPTION "The as-path prepend of the matched route. Up to 3 AS number can be displayed for the string. The usuage is: [][ ]" ::= { ipNewCfgRmapEntry 7 } ipNewCfgRmapMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The OSPF metric-type of the matched route." ::= { ipNewCfgRmapEntry 8 } ipNewCfgRmapDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ipNewCfgRmapEntry 9 } ipNewCfgRmapNexthop OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Peer address as nexthop of the matched route(only for BGP)." ::= { ipNewCfgRmapEntry 10 } ipAlistTableMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the IP route map table." ::= { ipRmapCfg 4 } ipCurCfgAlistTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgAlistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP route map access list in the current configuration block." ::= { ipRmapCfg 5 } ipCurCfgAlistEntry OBJECT-TYPE SYNTAX IpCurCfgAlistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an IP route map." INDEX { ipCurCfgAlistRmapIndex, ipCurCfgAlistIndex } ::= { ipCurCfgAlistTable 1 } IpCurCfgAlistEntry ::= SEQUENCE { ipCurCfgAlistRmapIndex Integer32, ipCurCfgAlistIndex Integer32, ipCurCfgAlistNwf INTEGER, ipCurCfgAlistMetric Unsigned32, ipCurCfgAlistAction INTEGER, ipCurCfgAlistState INTEGER } ipCurCfgAlistRmapIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The route map number for which the RMAP is related." ::= { ipCurCfgAlistEntry 1 } ipCurCfgAlistIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The access list number for which the access list is related." ::= { ipCurCfgAlistEntry 2 } ipCurCfgAlistNwf OBJECT-TYPE SYNTAX INTEGER (0..256) MAX-ACCESS read-only STATUS current DESCRIPTION "The network filter number of the route map access list. 0 means none" ::= { ipCurCfgAlistEntry 3 } ipCurCfgAlistMetric OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The metric of the route map access list. 4294967295 means none" ::= { ipCurCfgAlistEntry 4 } ipCurCfgAlistAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Action of the route map access list." ::= { ipCurCfgAlistEntry 5 } ipCurCfgAlistState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the route map access list." ::= { ipCurCfgAlistEntry 6 } ipNewCfgAlistTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgAlistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP route map access list in the current configuration block." ::= { ipRmapCfg 6 } ipNewCfgAlistEntry OBJECT-TYPE SYNTAX IpNewCfgAlistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an IP route map." INDEX { ipNewCfgAlistRmapIndex, ipNewCfgAlistIndex } ::= { ipNewCfgAlistTable 1 } IpNewCfgAlistEntry ::= SEQUENCE { ipNewCfgAlistRmapIndex Integer32, ipNewCfgAlistIndex Integer32, ipNewCfgAlistNwf INTEGER, ipNewCfgAlistMetric Unsigned32, ipNewCfgAlistAction INTEGER, ipNewCfgAlistState INTEGER, ipNewCfgAlistDelete INTEGER } ipNewCfgAlistRmapIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The route map number for which the RMAP is related." ::= { ipNewCfgAlistEntry 1 } ipNewCfgAlistIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The access list number for which the access list is related." ::= { ipNewCfgAlistEntry 2 } ipNewCfgAlistNwf OBJECT-TYPE SYNTAX INTEGER (1..256) MAX-ACCESS read-create STATUS current DESCRIPTION "The network filter number of the route map access list. 0 means none" ::= { ipNewCfgAlistEntry 3 } ipNewCfgAlistMetric OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The metric of the route map access list. 4294967295 means none" ::= { ipNewCfgAlistEntry 4 } ipNewCfgAlistAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Action of the route map access list." ::= { ipNewCfgAlistEntry 5 } ipNewCfgAlistState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable the route map access list." ::= { ipNewCfgAlistEntry 6 } ipNewCfgAlistDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ipNewCfgAlistEntry 7 } ipAspathTableMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the IP route map table." ::= { ipRmapCfg 7 } ipCurCfgAspathTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgAspathEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP route map access path configuration." ::= { ipRmapCfg 8 } ipCurCfgAspathEntry OBJECT-TYPE SYNTAX IpCurCfgAspathEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an IP route map." INDEX { ipCurCfgAspathRmapIndex, ipCurCfgAlistIndex } ::= { ipCurCfgAspathTable 1 } IpCurCfgAspathEntry ::= SEQUENCE { ipCurCfgAspathRmapIndex Integer32, ipCurCfgAspathIndex Integer32, ipCurCfgAspathAS INTEGER, ipCurCfgAspathAction INTEGER, ipCurCfgAspathState INTEGER } ipCurCfgAspathRmapIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The route map number for which the RMAP is related." ::= { ipCurCfgAspathEntry 1 } ipCurCfgAspathIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The access path number for which the access list is related." ::= { ipCurCfgAspathEntry 2 } ipCurCfgAspathAS OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The AS number of the route map access path. 0 means none" ::= { ipCurCfgAspathEntry 3 } ipCurCfgAspathAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Action of the route map access path." ::= { ipCurCfgAspathEntry 4 } ipCurCfgAspathState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the route map access path." ::= { ipCurCfgAspathEntry 5 } ipNewCfgAspathTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgAspathEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP route map access path configuration" ::= { ipRmapCfg 9 } ipNewCfgAspathEntry OBJECT-TYPE SYNTAX IpNewCfgAspathEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an IP route map." INDEX { ipNewCfgAspathRmapIndex, ipNewCfgAspathIndex } ::= { ipNewCfgAspathTable 1 } IpNewCfgAspathEntry ::= SEQUENCE { ipNewCfgAspathRmapIndex Integer32, ipNewCfgAspathIndex Integer32, ipNewCfgAspathAS INTEGER, ipNewCfgAspathAction INTEGER, ipNewCfgAspathState INTEGER, ipNewCfgAspathDelete INTEGER } ipNewCfgAspathRmapIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The route map number for which the RMAP is related." ::= { ipNewCfgAspathEntry 1 } ipNewCfgAspathIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The access path number for which the access list is related." ::= { ipNewCfgAspathEntry 2 } ipNewCfgAspathAS OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The AS number of the route map access path. 0 means none" ::= { ipNewCfgAspathEntry 3 } ipNewCfgAspathAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Action of the route map access path." ::= { ipNewCfgAspathEntry 4 } ipNewCfgAspathState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable the route map access path." ::= { ipNewCfgAspathEntry 5 } ipNewCfgAspathDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ipNewCfgAspathEntry 6 } -- -- IP BGP configuration -- bgpGeneral OBJECT IDENTIFIER ::= { bgpCfg 1 } bgpCurCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "BGP global state." ::= { bgpGeneral 1 } bgpNewCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Globally turn BGP on or off." ::= { bgpGeneral 2 } bgpCurCfgLocalPref OBJECT-TYPE SYNTAX Unsigned32 (0..4294967294) MAX-ACCESS read-only STATUS current DESCRIPTION "Local preference value." ::= { bgpGeneral 3 } bgpNewCfgLocalPref OBJECT-TYPE SYNTAX Unsigned32 (0..4294967294) MAX-ACCESS read-write STATUS current DESCRIPTION "Local Preference value." ::= { bgpGeneral 4 } bgpCurCfgASNumber OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The autonomous system (AS) number." ::= { bgpGeneral 5 } bgpNewCfgASNumber OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The autonomous system (AS) number." ::= { bgpGeneral 6 } bgpCurCfgEbgpMaxPaths OBJECT-TYPE SYNTAX Unsigned32 (0..4294967294) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum eBGP Paths." ::= { bgpGeneral 7 } bgpNewCfgEbgpMaxPaths OBJECT-TYPE SYNTAX Unsigned32 (0..4294967294) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum eBGP Paths." ::= { bgpGeneral 8 } bgpCurCfgIbgpMaxPaths OBJECT-TYPE SYNTAX Unsigned32 (0..4294967294) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum iBGP Paths." ::= { bgpGeneral 9 } bgpNewCfgIbgpMaxPaths OBJECT-TYPE SYNTAX Unsigned32 (0..4294967294) MAX-ACCESS read-write STATUS current DESCRIPTION "Maximum iBGP Paths." ::= { bgpGeneral 10 } bgpCurCfgAsn4Comp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "ASN4 to ASN2 compatibility." ::= { bgpGeneral 11 } bgpNewCfgAsn4Comp OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "ASN4 to ASN2 compatibility." ::= { bgpGeneral 12 } bgpCurCfgDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "BGP dscp marking value." ::= { bgpGeneral 13 } bgpNewCfgDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "BGP dscp marking value." ::= { bgpGeneral 14 } bgpNewCfgClusterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Cluster ID." ::= { bgpGeneral 15 } bgpCurCfgClusterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Cluster ID." ::= { bgpGeneral 16 } bgpNewCfgClientToClientReflection OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable client to client route reflection" ::= { bgpGeneral 17 } bgpCurCfgClientToClientReflection OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable client to client route reflection" ::= { bgpGeneral 18 } bgpPeerTableMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the BGP peer table." ::= { bgpCfg 2 } bgpCurCfgPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpCurCfgPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of BGP peer in the current configuration block." ::= { bgpCfg 3 } bgpCurCfgPeerEntry OBJECT-TYPE SYNTAX BgpCurCfgPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a BGP peer." INDEX { bgpCurCfgPeerIndex } ::= { bgpCurCfgPeerTable 1 } BgpCurCfgPeerEntry ::= SEQUENCE { bgpCurCfgPeerIndex Integer32, bgpCurCfgPeerRemoteAddr IpAddress, bgpCurCfgPeerRemoteAs INTEGER, bgpCurCfgPeerPassive INTEGER, bgpCurCfgPeerHold INTEGER, bgpCurCfgPeerAlive INTEGER, bgpCurCfgPeerAdvert INTEGER, bgpCurCfgPeerRetry INTEGER, bgpCurCfgPeerOrig INTEGER, bgpCurCfgPeerRipState INTEGER, bgpCurCfgPeerTtl INTEGER, bgpCurCfgPeerPassword DisplayString, bgpCurCfgPeerState INTEGER, bgpCurCfgPeerMetric Unsigned32, bgpCurCfgPeerDefaultAction INTEGER, bgpCurCfgPeerOspfState INTEGER, bgpCurCfgPeerFixedState INTEGER, bgpCurCfgPeerStaticState INTEGER, bgpCurCfgPeerInRmapList OCTET STRING, bgpCurCfgPeerOutRmapList OCTET STRING , bgpCurCfgPeerUpdateSrcIf INTEGER , bgpCurCfgPeerUpdateSrcLoopIf INTEGER , bgpCurCfgPeerTtlSecHops INTEGER ,bgpCurCfgPeerNexthopSelf INTEGER , bgpCurCfgPeerClient INTEGER } bgpCurCfgPeerIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP peer number for which the BGP peer table is related." ::= { bgpCurCfgPeerEntry 1 } bgpCurCfgPeerRemoteAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The remote IP address of the BGP peer." ::= { bgpCurCfgPeerEntry 2 } bgpCurCfgPeerRemoteAs OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The remote AS number of the BGP peer. 0 means none" ::= { bgpCurCfgPeerEntry 3 } bgpCurCfgPeerTtl OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The time-to-live value of the BGP peer IP datagram. 0 means none." ::= { bgpCurCfgPeerEntry 4 } bgpCurCfgPeerState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the peer." ::= { bgpCurCfgPeerEntry 5 } bgpCurCfgPeerMetric OBJECT-TYPE SYNTAX Unsigned32 (0..4294967294) MAX-ACCESS read-only STATUS current DESCRIPTION "The metric value of the BGP peer. A value of '0' means none" ::= { bgpCurCfgPeerEntry 10 } bgpCurCfgPeerDefaultAction OBJECT-TYPE SYNTAX INTEGER { none(1), import(2), originate(3), redistribute(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of default route action." ::= { bgpCurCfgPeerEntry 11 } bgpCurCfgPeerOspfState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable advertising OSPF routes." ::= { bgpCurCfgPeerEntry 12 } bgpCurCfgPeerFixedState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable advertising fixed routes." ::= { bgpCurCfgPeerEntry 13 } bgpCurCfgPeerStaticState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable advertising static routes." ::= { bgpCurCfgPeerEntry 14 } bgpCurCfgPeerInRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the in route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { bgpCurCfgPeerEntry 16 } bgpCurCfgPeerOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { bgpCurCfgPeerEntry 17 } bgpCurCfgPeerHold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The hold time" ::= { bgpCurCfgPeerEntry 18 } bgpCurCfgPeerAlive OBJECT-TYPE SYNTAX INTEGER (0..21845) MAX-ACCESS read-only STATUS current DESCRIPTION "The keep alive time" ::= { bgpCurCfgPeerEntry 19 } bgpCurCfgPeerAdvert OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The min time between advertisements" ::= { bgpCurCfgPeerEntry 20 } bgpCurCfgPeerRetry OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The connect retry interval" ::= { bgpCurCfgPeerEntry 21 } bgpCurCfgPeerOrig OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The min time between route originations" ::= { bgpCurCfgPeerEntry 22 } bgpCurCfgPeerRipState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable advertising RIP routes" ::= { bgpCurCfgPeerEntry 23 } bgpCurCfgPeerPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "Peer BGP password" ::= { bgpCurCfgPeerEntry 24 } bgpCurCfgPeerPassive OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable BGP passive peer" ::= { bgpCurCfgPeerEntry 25 } bgpCurCfgPeerUpdateSrcIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "BGP peer update source interface index" ::= { bgpCurCfgPeerEntry 30 } bgpCurCfgPeerUpdateSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "BGP peer update source loopback interface index" ::= { bgpCurCfgPeerEntry 31 } bgpCurCfgPeerTtlSecHops OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP ttl security hops. 0 means none." ::= { bgpCurCfgPeerEntry 32 } bgpCurCfgPeerNexthopSelf OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/Disable using this router as next-hop in BGP updates." ::= { bgpCurCfgPeerEntry 33 } bgpCurCfgPeerClient OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable BGP client peer" ::= { bgpCurCfgPeerEntry 34 } bgpNewCfgPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpNewCfgPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of BGP peer in the new configuration block." ::= { bgpCfg 4 } bgpNewCfgPeerEntry OBJECT-TYPE SYNTAX BgpNewCfgPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a BGP peer." INDEX { bgpNewCfgPeerIndex } ::= { bgpNewCfgPeerTable 1 } BgpNewCfgPeerEntry ::= SEQUENCE { bgpNewCfgPeerIndex Integer32, bgpNewCfgPeerRemoteAddr IpAddress, bgpNewCfgPeerRemoteAs INTEGER, bgpNewCfgPeerPassive INTEGER, bgpNewCfgPeerHold INTEGER, bgpNewCfgPeerAlive INTEGER, bgpNewCfgPeerAdvert INTEGER, bgpNewCfgPeerRetry INTEGER, bgpNewCfgPeerOrig INTEGER, bgpNewCfgPeerRipState INTEGER, bgpNewCfgPeerTtl INTEGER, bgpNewCfgPeerPassword DisplayString, bgpNewCfgPeerState INTEGER, bgpNewCfgPeerDelete INTEGER, bgpNewCfgPeerMetric Unsigned32, bgpNewCfgPeerDefaultAction INTEGER, bgpNewCfgPeerOspfState INTEGER, bgpNewCfgPeerFixedState INTEGER, bgpNewCfgPeerStaticState INTEGER, bgpNewCfgPeerInRmapList OCTET STRING, bgpNewCfgPeerOutRmapList OCTET STRING, bgpNewCfgPeerAddInRmap Integer32, bgpNewCfgPeerAddOutRmap Integer32, bgpNewCfgPeerRemoveInRmap Integer32, bgpNewCfgPeerRemoveOutRmap Integer32 , bgpNewCfgPeerUpdateSrcIf INTEGER , bgpNewCfgPeerUpdateSrcLoopIf INTEGER , bgpNewCfgPeerTtlSecHops INTEGER ,bgpNewCfgPeerNexthopSelf INTEGER , bgpNewCfgPeerClient INTEGER } bgpNewCfgPeerIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP peer number for which the BGP peer table is related." ::= { bgpNewCfgPeerEntry 1} bgpNewCfgPeerRemoteAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The remote IP address of the BGP peer." ::= { bgpNewCfgPeerEntry 2 } bgpNewCfgPeerRemoteAs OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The remote AS number of the BGP peer. 0 means none" ::= { bgpNewCfgPeerEntry 3 } bgpNewCfgPeerTtl OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The time-to-live value of the BGP peer IP datagram. 0 means none." ::= { bgpNewCfgPeerEntry 4 } bgpNewCfgPeerState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable the peer." ::= { bgpNewCfgPeerEntry 5 } bgpNewCfgPeerDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { bgpNewCfgPeerEntry 6 } bgpNewCfgPeerMetric OBJECT-TYPE SYNTAX Unsigned32 (0..4294967294) MAX-ACCESS read-create STATUS current DESCRIPTION "The metric value of the BGP peer. A value of '0' means none" ::= { bgpNewCfgPeerEntry 10 } bgpNewCfgPeerDefaultAction OBJECT-TYPE SYNTAX INTEGER { none(1), import(2), originate(3), redistribute(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The value of default route action." ::= { bgpNewCfgPeerEntry 11 } bgpNewCfgPeerOspfState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable advertising OSPF routes." ::= { bgpNewCfgPeerEntry 12 } bgpNewCfgPeerFixedState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable advertising fixed routes." ::= { bgpNewCfgPeerEntry 13 } bgpNewCfgPeerStaticState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable advertising static routes." ::= { bgpNewCfgPeerEntry 14 } bgpNewCfgPeerInRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the in route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { bgpNewCfgPeerEntry 16 } bgpNewCfgPeerOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { bgpNewCfgPeerEntry 17 } bgpNewCfgPeerAddInRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The route map to be add into in-rmap list. When read, 0 is returned." ::= { bgpNewCfgPeerEntry 18 } bgpNewCfgPeerAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { bgpNewCfgPeerEntry 19 } bgpNewCfgPeerRemoveInRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { bgpNewCfgPeerEntry 20 } bgpNewCfgPeerRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { bgpNewCfgPeerEntry 21 } bgpNewCfgPeerHold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The hold time" ::= { bgpNewCfgPeerEntry 22 } bgpNewCfgPeerAlive OBJECT-TYPE SYNTAX INTEGER (0..21845) MAX-ACCESS read-create STATUS current DESCRIPTION "The keep alive time" ::= { bgpNewCfgPeerEntry 23 } bgpNewCfgPeerAdvert OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The min time between advertisements" ::= { bgpNewCfgPeerEntry 24 } bgpNewCfgPeerRetry OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The connect retry interval" ::= { bgpNewCfgPeerEntry 25 } bgpNewCfgPeerOrig OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The min time between route originations" ::= { bgpNewCfgPeerEntry 26 } bgpNewCfgPeerRipState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable advertising RIP routes" ::= { bgpNewCfgPeerEntry 27 } bgpNewCfgPeerPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "Peer BGP password" ::= { bgpNewCfgPeerEntry 28 } bgpNewCfgPeerPassive OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable BGP passive peer" ::= { bgpNewCfgPeerEntry 29 } bgpNewCfgPeerUpdateSrcIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "BGP peer update source interface index" ::= { bgpNewCfgPeerEntry 30 } bgpNewCfgPeerUpdateSrcLoopIf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "BGP peer update source loopback interface index" ::= { bgpNewCfgPeerEntry 31 } bgpNewCfgPeerTtlSecHops OBJECT-TYPE SYNTAX INTEGER (0..254) MAX-ACCESS read-create STATUS current DESCRIPTION "The BGP ttl security hops. 0 means none." ::= { bgpNewCfgPeerEntry 32 } bgpNewCfgPeerNexthopSelf OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/Disable using this router as next-hop in BGP updates." ::= { bgpNewCfgPeerEntry 33 } bgpNewCfgPeerClient OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable BGP client peer" ::= { bgpNewCfgPeerEntry 34 } -- -- BGP Aggregation Table -- bgpAggrTableMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the BGP aggregation table." ::= { bgpCfg 5 } bgpCurCfgAggrTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpCurCfgAggrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of BGP aggregation configuration." ::= { bgpCfg 6 } bgpCurCfgAggrEntry OBJECT-TYPE SYNTAX BgpCurCfgAggrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a BGP aggregation." INDEX { bgpCurCfgAggrIndex } ::= { bgpCurCfgAggrTable 1 } BgpCurCfgAggrEntry ::= SEQUENCE { bgpCurCfgAggrIndex Integer32, bgpCurCfgAggrAddr IpAddress, bgpCurCfgAggrMask IpAddress, bgpCurCfgAggrState INTEGER } bgpCurCfgAggrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The aggregation number for which the BGP aggregation is related." ::= { bgpCurCfgAggrEntry 1} bgpCurCfgAggrAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the BGP aggregation." ::= { bgpCurCfgAggrEntry 2 } bgpCurCfgAggrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The subnet mask of the BGP aggregation." ::= { bgpCurCfgAggrEntry 3 } bgpCurCfgAggrState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable the BGP aggregation." ::= { bgpCurCfgAggrEntry 4 } bgpNewCfgAggrTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpNewCfgAggrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of BGP aggregation configuration." ::= { bgpCfg 7 } bgpNewCfgAggrEntry OBJECT-TYPE SYNTAX BgpNewCfgAggrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an BGP aggregation." INDEX { bgpNewCfgAggrIndex } ::= { bgpNewCfgAggrTable 1 } BgpNewCfgAggrEntry ::= SEQUENCE { bgpNewCfgAggrIndex Integer32, bgpNewCfgAggrAddr IpAddress, bgpNewCfgAggrMask IpAddress, bgpNewCfgAggrState INTEGER, bgpNewCfgAggrDelete INTEGER } bgpNewCfgAggrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The aggregation number for which the BGP aggregation is related." ::= { bgpNewCfgAggrEntry 1} bgpNewCfgAggrAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of the BGP aggregation." ::= { bgpNewCfgAggrEntry 2 } bgpNewCfgAggrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The subnet mask of the BGP aggregation." ::= { bgpNewCfgAggrEntry 3 } bgpNewCfgAggrState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable the BGP aggregation." ::= { bgpNewCfgAggrEntry 4 } bgpNewCfgAggrDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { bgpNewCfgAggrEntry 5 } -- -- IP OSPF configuration -- ospfGeneral OBJECT IDENTIFIER ::= { ospfCfg 1 } ospfCurCfgDefaultRouteMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-only STATUS current DESCRIPTION "Specify the metric to be assigned." ::= { ospfGeneral 1 } ospfNewCfgDefaultRouteMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the metric to be assigned." ::= { ospfGeneral 2 } ospfCurCfgDefaultRouteMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specify the AS External metric type to be assigned." ::= { ospfGeneral 3 } ospfNewCfgDefaultRouteMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specify the AS External metric type to be assigned." ::= { ospfGeneral 4 } ospfIntfTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPF Interface table." ::= { ospfGeneral 5 } ospfAreaTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPF Area table." ::= { ospfGeneral 6 } ospfRangeTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPF Range table." ::= { ospfGeneral 7 } ospfVirtIntfTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPF Virtual Interface table." ::= { ospfGeneral 8 } ospfHostTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPF Host table." ::= { ospfGeneral 9 } ospfCurCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPF global state." ::= { ospfGeneral 10 } ospfNewCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Globally turn OSPF on or off." ::= { ospfGeneral 11 } ospfCurCfgLSDB OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The LSDB limit for external LSA." ::= { ospfGeneral 12 } ospfNewCfgLSDB OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Set the LSDB limit for external LSA." ::= { ospfGeneral 13 } ospfCurCfgAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfCurCfgAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF area in the current configuration block." ::= { ospfCfg 2 } ospfCurCfgAreaEntry OBJECT-TYPE SYNTAX OspfCurCfgAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPF area." INDEX { ospfCurCfgAreaIndex } ::= { ospfCurCfgAreaTable 1 } OspfCurCfgAreaEntry ::= SEQUENCE { ospfCurCfgAreaIndex Integer32, ospfCurCfgAreaId IpAddress, ospfCurCfgAreaSpfInterval INTEGER, ospfCurCfgAreaAuthType INTEGER, ospfCurCfgAreaType INTEGER, ospfCurCfgAreaMetric INTEGER, ospfCurCfgAreaStatus INTEGER } ospfCurCfgAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF area number for which the OSPF area table is related." ::= { ospfCurCfgAreaEntry 1} ospfCurCfgAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the OSPF area." ::= { ospfCurCfgAreaEntry 2 } ospfCurCfgAreaSpfInterval OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The SPF interval for the OSPF area." ::= { ospfCurCfgAreaEntry 3 } ospfCurCfgAreaAuthType OBJECT-TYPE SYNTAX INTEGER { none(1), password(2), md5(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of authentication being used. none(1) - no authentication password(2) - use password md5(3) - use MD5 authentication." ::= { ospfCurCfgAreaEntry 4 } ospfCurCfgAreaType OBJECT-TYPE SYNTAX INTEGER { transit(0), stub(1), nssa(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of Area. transit(0) stub(1) nssa(2)" ::= { ospfCurCfgAreaEntry 5 } ospfCurCfgAreaMetric OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Metric (1-65535)" ::= { ospfCurCfgAreaEntry 6 } ospfCurCfgAreaStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status disabled(0) enabled(1)" ::= { ospfCurCfgAreaEntry 7 } ospfNewCfgAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfNewCfgAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF area in the new configuration block." ::= { ospfCfg 3 } ospfNewCfgAreaEntry OBJECT-TYPE SYNTAX OspfNewCfgAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPF area." INDEX { ospfNewCfgAreaIndex } ::= { ospfNewCfgAreaTable 1 } OspfNewCfgAreaEntry ::= SEQUENCE { ospfNewCfgAreaIndex Integer32, ospfNewCfgAreaId IpAddress, ospfNewCfgAreaSpfInterval INTEGER, ospfNewCfgAreaAuthType INTEGER, ospfNewCfgAreaType INTEGER, ospfNewCfgAreaMetric INTEGER, ospfNewCfgAreaStatus INTEGER, ospfNewCfgAreaDelete INTEGER } ospfNewCfgAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF area number for which the OSPF area table is related." ::= { ospfNewCfgAreaEntry 1} ospfNewCfgAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP Address of the OSPF area." ::= { ospfNewCfgAreaEntry 2 } ospfNewCfgAreaSpfInterval OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The SPF interval for the OSPF area." ::= { ospfNewCfgAreaEntry 3 } ospfNewCfgAreaAuthType OBJECT-TYPE SYNTAX INTEGER { none(1), password(2), md5(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Type of authentication being used. none(1) - no authentication password(2) - use password. md5(3) - use MD5 authentication." ::= { ospfNewCfgAreaEntry 4 } ospfNewCfgAreaType OBJECT-TYPE SYNTAX INTEGER { transit(0), stub(1), nssa(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of Area. transit(0) stub(1) nssa(2)" ::= { ospfNewCfgAreaEntry 5 } ospfNewCfgAreaMetric OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Metric (1-65535)" ::= { ospfNewCfgAreaEntry 6 } ospfNewCfgAreaStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Status disabled(0) enabled(1)" ::= { ospfNewCfgAreaEntry 7 } ospfNewCfgAreaDelete OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete the area no(0), yes(1)" ::= { ospfNewCfgAreaEntry 8 } -- OSPF Host Table ospfCurCfgHostTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfCurCfgHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Host configuration." ::= { ospfCfg 12 } ospfCurCfgHostEntry OBJECT-TYPE SYNTAX OspfCurCfgHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPF host." INDEX { ospfCurCfgHostIndex } ::= { ospfCurCfgHostTable 1 } OspfCurCfgHostEntry ::= SEQUENCE { ospfCurCfgHostIndex Integer32, ospfCurCfgHostIpAddr IpAddress, ospfCurCfgHostAreaIndex Integer32, ospfCurCfgHostCost INTEGER, ospfCurCfgHostState INTEGER } ospfCurCfgHostIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF host number for which the OSPF host table is related." ::= { ospfCurCfgHostEntry 1} ospfCurCfgHostIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the OSPF host." ::= { ospfCurCfgHostEntry 2 } ospfCurCfgHostAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The area index." ::= { ospfCurCfgHostEntry 3 } ospfCurCfgHostCost OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the OSPF host." ::= { ospfCurCfgHostEntry 4 } ospfCurCfgHostState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable an OSPF Host" ::= { ospfCurCfgHostEntry 5 } ospfNewCfgHostTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfNewCfgHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Host configuration." ::= { ospfCfg 13 } ospfNewCfgHostEntry OBJECT-TYPE SYNTAX OspfNewCfgHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPF host." INDEX { ospfNewCfgHostIndex } ::= { ospfNewCfgHostTable 1 } OspfNewCfgHostEntry ::= SEQUENCE { ospfNewCfgHostIndex Integer32, ospfNewCfgHostIpAddr IpAddress, ospfNewCfgHostAreaIndex Integer32, ospfNewCfgHostCost INTEGER, ospfNewCfgHostState INTEGER, ospfNewCfgHostDelete INTEGER } ospfNewCfgHostIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF host number for which the OSPF host table is related." ::= { ospfNewCfgHostEntry 1} ospfNewCfgHostIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP Address of the OSPF host." ::= { ospfNewCfgHostEntry 2 } ospfNewCfgHostAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The OSPF area index." ::= { ospfNewCfgHostEntry 3 } ospfNewCfgHostCost OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The cost of the OSPF host." ::= { ospfNewCfgHostEntry 4 } ospfNewCfgHostState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable an OSPF Host" ::= { ospfNewCfgHostEntry 5 } ospfNewCfgHostDelete OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete the OSPF host: no(0), yes(1)" ::= { ospfNewCfgHostEntry 6 } ospfMdkeyTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPF Mdkey table." ::= { ospfCfg 11 } ospfCurCfgMdkeyTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfCurCfgMdkeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF MD5 keys in the current configuration block." ::= { ospfCfg 5 } ospfCurCfgMdkeyEntry OBJECT-TYPE SYNTAX OspfCurCfgMdkeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF MD keys table." INDEX { ospfCurCfgMdkeyIndex } ::= { ospfCurCfgMdkeyTable 1 } OspfCurCfgMdkeyEntry ::= SEQUENCE { ospfCurCfgMdkeyIndex Integer32, ospfCurCfgMdkeyKey DisplayString } ospfCurCfgMdkeyIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF MD5 Key number for which the OSPF MdKey table is related." ::= { ospfCurCfgMdkeyEntry 1} ospfCurCfgMdkeyKey OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The character string representing the MD5 Key." ::= { ospfCurCfgMdkeyEntry 2 } ospfNewCfgMdkeyTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfNewCfgMdkeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF MD5 keys in the new configuration block." ::= { ospfCfg 6 } ospfNewCfgMdkeyEntry OBJECT-TYPE SYNTAX OspfNewCfgMdkeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF MD keys table." INDEX { ospfNewCfgMdkeyIndex } ::= { ospfNewCfgMdkeyTable 1 } OspfNewCfgMdkeyEntry ::= SEQUENCE { ospfNewCfgMdkeyIndex Integer32, ospfNewCfgMdkeyKey DisplayString, ospfNewCfgMdkeyDelete INTEGER } ospfNewCfgMdkeyIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF MD5 Key number for which the OSPF MdKey table is related." ::= { ospfNewCfgMdkeyEntry 1} ospfNewCfgMdkeyKey OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The character string representing the MD5 Key." ::= { ospfNewCfgMdkeyEntry 2 } ospfNewCfgMdkeyDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ospfNewCfgMdkeyEntry 3} ospfCurCfgIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfCurCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Interface in the current configuration block." ::= { ospfCfg 7 } ospfCurCfgIntfEntry OBJECT-TYPE SYNTAX OspfCurCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF Interface." INDEX { ospfCurCfgIntfIndex } ::= { ospfCurCfgIntfTable 1 } OspfCurCfgIntfEntry ::= SEQUENCE { ospfCurCfgIntfIndex Integer32, ospfCurCfgIntfArea INTEGER, ospfCurCfgIntfMdkey INTEGER, ospfCurCfgIntfCost INTEGER, ospfCurCfgIntfPrio INTEGER, ospfCurCfgIntfHello INTEGER, ospfCurCfgIntfHelloMS INTEGER, ospfCurCfgIntfDead INTEGER, ospfCurCfgIntfDeadMS INTEGER, ospfCurCfgIntfTrans INTEGER, ospfCurCfgIntfRetra INTEGER, ospfCurCfgIntfAuthKey DisplayString, ospfCurCfgIntfPassive INTEGER, ospfCurCfgIntfPtop INTEGER, ospfCurCfgIntfStatus INTEGER } ospfCurCfgIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Interface number for which the OSPF Interface table is related." ::= { ospfCurCfgIntfEntry 1} ospfCurCfgIntfArea OBJECT-TYPE SYNTAX INTEGER (0..2) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the area that the interface belongs (0..2)" ::= { ospfCurCfgIntfEntry 2 } ospfCurCfgIntfMdkey OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The MD5 key for the OSPF interface 0 (none) no MD5 authentication." ::= { ospfCurCfgIntfEntry 3 } ospfCurCfgIntfCost OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface cost" ::= { ospfCurCfgIntfEntry 4 } ospfCurCfgIntfPrio OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface router priority" ::= { ospfCurCfgIntfEntry 5 } ospfCurCfgIntfHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Hello interval" ::= { ospfCurCfgIntfEntry 6 } ospfCurCfgIntfHelloMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Hello interval seconds(0), milliseconds(1)" ::= { ospfCurCfgIntfEntry 7 } ospfCurCfgIntfDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Dead interval" ::= { ospfCurCfgIntfEntry 8 } ospfCurCfgIntfDeadMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Dead interval seconds(0), milliseconds(1)" ::= { ospfCurCfgIntfEntry 9 } ospfCurCfgIntfTrans OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "Transit delay" ::= { ospfCurCfgIntfEntry 10 } ospfCurCfgIntfRetra OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "Retransmit interval" ::= { ospfCurCfgIntfEntry 11 } ospfCurCfgIntfAuthKey OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Authentication Key" ::= { ospfCurCfgIntfEntry 12 } ospfCurCfgIntfPassive OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Passive interface disabled(0), enabled(1)" ::= { ospfCurCfgIntfEntry 13 } ospfCurCfgIntfPtop OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Point-to-point interface disabled(0), enabled(1)" ::= { ospfCurCfgIntfEntry 15 } ospfCurCfgIntfStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of the interface disabled(0), enabled(1)" ::= { ospfCurCfgIntfEntry 14 } ospfNewCfgIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfNewCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF interface in the new configuration block." ::= { ospfCfg 8 } ospfNewCfgIntfEntry OBJECT-TYPE SYNTAX OspfNewCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF interface." INDEX { ospfNewCfgIntfIndex } ::= { ospfNewCfgIntfTable 1 } OspfNewCfgIntfEntry ::= SEQUENCE { ospfNewCfgIntfIndex Integer32, ospfNewCfgIntfArea INTEGER, ospfNewCfgIntfMdkey INTEGER, ospfNewCfgIntfCost INTEGER, ospfNewCfgIntfPrio INTEGER, ospfNewCfgIntfHello INTEGER, ospfNewCfgIntfHelloMS INTEGER, ospfNewCfgIntfDead INTEGER, ospfNewCfgIntfDeadMS INTEGER, ospfNewCfgIntfTrans INTEGER, ospfNewCfgIntfRetra INTEGER, ospfNewCfgIntfAuthKey DisplayString, ospfNewCfgIntfPassive INTEGER, ospfNewCfgIntfPtop INTEGER, ospfNewCfgIntfStatus INTEGER, ospfNewCfgIntfDelete INTEGER } ospfNewCfgIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Interface number for which the OSPF Interface table is related." ::= { ospfNewCfgIntfEntry 1} ospfNewCfgIntfArea OBJECT-TYPE SYNTAX INTEGER (0..19) MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the area that the interface belongs" ::= { ospfNewCfgIntfEntry 2 } ospfNewCfgIntfMdkey OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The MD5 key for the OSPF interface 0 (none) no MD5 authentication." ::= { ospfNewCfgIntfEntry 3 } ospfNewCfgIntfCost OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Interface cost(1..65535)" ::= { ospfNewCfgIntfEntry 4 } ospfNewCfgIntfPrio OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Interface router priority(0..255)" ::= { ospfNewCfgIntfEntry 5 } ospfNewCfgIntfHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Hello interval(1..65535s | 50..65535ms)" ::= { ospfNewCfgIntfEntry 6 } ospfNewCfgIntfHelloMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Units of time measurement for Hello interval seconds(0), milliseconds(1)" ::= { ospfNewCfgIntfEntry 7 } ospfNewCfgIntfDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Dead interval(1..65535s |1000..65535ms)" ::= { ospfNewCfgIntfEntry 8 } ospfNewCfgIntfDeadMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Units of time measurement for Dead interval seconds(0), milliseconds(1)" ::= { ospfNewCfgIntfEntry 9 } ospfNewCfgIntfTrans OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-create STATUS current DESCRIPTION "Transit delay(1..3600)" ::= { ospfNewCfgIntfEntry 10 } ospfNewCfgIntfRetra OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-create STATUS current DESCRIPTION "Retransmit interval(1..3600)" ::= { ospfNewCfgIntfEntry 11 } ospfNewCfgIntfAuthKey OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-create STATUS current DESCRIPTION "Authentication Key" ::= { ospfNewCfgIntfEntry 12 } ospfNewCfgIntfPassive OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Passive interface disabled(0), enabled(1)" ::= { ospfNewCfgIntfEntry 13 } ospfNewCfgIntfPtop OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Point-to-point interface disabled(0), enabled(1)" ::= { ospfNewCfgIntfEntry 16 } ospfNewCfgIntfStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Status of the interface disabled(0), enabled(1)" ::= { ospfNewCfgIntfEntry 14 } ospfNewCfgIntfDelete OBJECT-TYPE SYNTAX INTEGER { other(0), delete(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete the interface other(0), delete(1)" ::= { ospfNewCfgIntfEntry 15 } ospfCurCfgLoopIfTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfCurCfgLoopIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Loopback Interfaces in the current configuration block." ::= { ospfCfg 20 } ospfCurCfgLoopIfEntry OBJECT-TYPE SYNTAX OspfCurCfgLoopIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF Loopback Interface." INDEX { ospfCurCfgLoopIfIndex } ::= { ospfCurCfgLoopIfTable 1 } OspfCurCfgLoopIfEntry ::= SEQUENCE { ospfCurCfgLoopIfIndex Integer32, ospfCurCfgLoopIfArea INTEGER, ospfCurCfgLoopIfStatus INTEGER } ospfCurCfgLoopIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Loopback Interface number for which the OSPF Interface table is related." ::= { ospfCurCfgLoopIfEntry 1} ospfCurCfgLoopIfArea OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the area that the loopback interface belongs" ::= { ospfCurCfgLoopIfEntry 2 } ospfCurCfgLoopIfStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of the loopback interface disabled(0), enabled(1)" ::= { ospfCurCfgLoopIfEntry 3 } ospfNewCfgLoopIfTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfNewCfgLoopIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF loopback interface in the new configuration block." ::= { ospfCfg 21 } ospfNewCfgLoopIfEntry OBJECT-TYPE SYNTAX OspfNewCfgLoopIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF loopback interface." INDEX { ospfNewCfgLoopIfIndex } ::= { ospfNewCfgLoopIfTable 1 } OspfNewCfgLoopIfEntry ::= SEQUENCE { ospfNewCfgLoopIfIndex Integer32, ospfNewCfgLoopIfArea INTEGER, ospfNewCfgLoopIfStatus INTEGER, ospfNewCfgLoopIfDelete INTEGER } ospfNewCfgLoopIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF loopback interface number for which the OSPF Loopback Interface table is related." ::= { ospfNewCfgLoopIfEntry 1} ospfNewCfgLoopIfArea OBJECT-TYPE SYNTAX INTEGER (0..5) MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the area that the loopback interface belongs (0..5)" ::= { ospfNewCfgLoopIfEntry 2 } ospfNewCfgLoopIfStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Status of the loopback interface disabled(0), enabled(1)" ::= { ospfNewCfgLoopIfEntry 3 } ospfNewCfgLoopIfDelete OBJECT-TYPE SYNTAX INTEGER { other(0), delete(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete the loopback interface other(0), delete(1)" ::= { ospfNewCfgLoopIfEntry 4 } ospfCurCfgVirtIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfCurCfgVirtIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Virtual Interface configuration in the current configuration." ::= { ospfCfg 9 } ospfCurCfgVirtIntfEntry OBJECT-TYPE SYNTAX OspfCurCfgVirtIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF virtual Interface." INDEX { ospfCurCfgVirtIntfIndex } ::= { ospfCurCfgVirtIntfTable 1 } OspfCurCfgVirtIntfEntry ::= SEQUENCE { ospfCurCfgVirtIntfIndex Integer32, ospfCurCfgVirtIntfAreaId INTEGER, ospfCurCfgVirtIntfNbr IpAddress, ospfCurCfgVirtIntfMdkey INTEGER, ospfCurCfgVirtIntfHello INTEGER, ospfCurCfgVirtIntfHelloMS INTEGER, ospfCurCfgVirtIntfDead INTEGER, ospfCurCfgVirtIntfDeadMS INTEGER, ospfCurCfgVirtIntfTrans INTEGER, ospfCurCfgVirtIntfRetra INTEGER, ospfCurCfgVirtIntfAuthKey DisplayString, ospfCurCfgVirtIntfStatus INTEGER } ospfCurCfgVirtIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Virtual Interface number for which the OSPF Virtual Interface table is related." ::= { ospfCurCfgVirtIntfEntry 1} ospfCurCfgVirtIntfAreaId OBJECT-TYPE SYNTAX INTEGER (0..19) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the OSPF area to which this virtual interface belongs." ::= { ospfCurCfgVirtIntfEntry 2 } ospfCurCfgVirtIntfNbr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the OSPF neighbor for this virtual interface." ::= { ospfCurCfgVirtIntfEntry 3 } ospfCurCfgVirtIntfMdkey OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The MD5 key for the OSPF virtual interface 0 (none) no MD5 authentication." ::= { ospfCurCfgVirtIntfEntry 4 } ospfCurCfgVirtIntfHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Hello interval" ::= { ospfCurCfgVirtIntfEntry 5 } ospfCurCfgVirtIntfHelloMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Hello interval seconds(0), milliseconds(1)" ::= { ospfCurCfgVirtIntfEntry 6 } ospfCurCfgVirtIntfDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Dead interval" ::= { ospfCurCfgVirtIntfEntry 7 } ospfCurCfgVirtIntfDeadMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Dead interval seconds(0), milliseconds(1)" ::= { ospfCurCfgVirtIntfEntry 8 } ospfCurCfgVirtIntfTrans OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "Transit delay" ::= { ospfCurCfgVirtIntfEntry 9 } ospfCurCfgVirtIntfRetra OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "Retransmit interval" ::= { ospfCurCfgVirtIntfEntry 10 } ospfCurCfgVirtIntfAuthKey OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Authentication Key" ::= { ospfCurCfgVirtIntfEntry 11 } ospfCurCfgVirtIntfStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status disabled(0), enabled(1)" ::= { ospfCurCfgVirtIntfEntry 12 } ospfNewCfgVirtIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfNewCfgVirtIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Virtual interface in the new configuration block." ::= { ospfCfg 10 } ospfNewCfgVirtIntfEntry OBJECT-TYPE SYNTAX OspfNewCfgVirtIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF virtual interface." INDEX { ospfNewCfgVirtIntfIndex } ::= { ospfNewCfgVirtIntfTable 1 } OspfNewCfgVirtIntfEntry ::= SEQUENCE { ospfNewCfgVirtIntfIndex Integer32, ospfNewCfgVirtIntfAreaId INTEGER, ospfNewCfgVirtIntfNbr IpAddress, ospfNewCfgVirtIntfMdkey INTEGER, ospfNewCfgVirtIntfHello INTEGER, ospfNewCfgVirtIntfHelloMS INTEGER, ospfNewCfgVirtIntfDead INTEGER, ospfNewCfgVirtIntfDeadMS INTEGER, ospfNewCfgVirtIntfTrans INTEGER, ospfNewCfgVirtIntfRetra INTEGER, ospfNewCfgVirtIntfAuthKey DisplayString, ospfNewCfgVirtIntfStatus INTEGER, ospfNewCfgVirtIntfDelete INTEGER } ospfNewCfgVirtIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Virtual Interface number for which the OSPF Virtual Interface table is related." ::= { ospfNewCfgVirtIntfEntry 1} ospfNewCfgVirtIntfAreaId OBJECT-TYPE SYNTAX INTEGER (0..19) MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the OSPF area to which this virtual interface belongs." ::= { ospfNewCfgVirtIntfEntry 2 } ospfNewCfgVirtIntfNbr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP Address of the OSPF neighbor for this virtual interface." ::= { ospfNewCfgVirtIntfEntry 3 } ospfNewCfgVirtIntfMdkey OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The MD5 key for the OSPF virtual interface 0 (none) no MD5 authentication." ::= { ospfNewCfgVirtIntfEntry 4 } ospfNewCfgVirtIntfHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Hello interval(1..65535s | 50..65535ms)" ::= { ospfNewCfgVirtIntfEntry 5 } ospfNewCfgVirtIntfHelloMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Units of time measurement fo Hello interval seconds(0), milliseconds(1) " ::= { ospfNewCfgVirtIntfEntry 6 } ospfNewCfgVirtIntfDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Dead interval(1..65535s | 1000..65535ms)" ::= { ospfNewCfgVirtIntfEntry 7 } ospfNewCfgVirtIntfDeadMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Units of time measurement fo Dead interval seconds(0), milliseconds(1) " ::= { ospfNewCfgVirtIntfEntry 8 } ospfNewCfgVirtIntfTrans OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-create STATUS current DESCRIPTION "Transit delay(1..3600)" ::= { ospfNewCfgVirtIntfEntry 9 } ospfNewCfgVirtIntfRetra OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-create STATUS current DESCRIPTION "Retransmit interval(1..3600)" ::= { ospfNewCfgVirtIntfEntry 10 } ospfNewCfgVirtIntfAuthKey OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-create STATUS current DESCRIPTION "Authentication Key SIZE(0..8)" ::= { ospfNewCfgVirtIntfEntry 11 } ospfNewCfgVirtIntfStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Status disabled(0), enabled(1) " ::= { ospfNewCfgVirtIntfEntry 12 } ospfNewCfgVirtIntfDelete OBJECT-TYPE SYNTAX INTEGER { other(0), delete(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete other(0), delete(1)" ::= { ospfNewCfgVirtIntfEntry 13 } -- ospf range ospfCurCfgRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfCurCfgRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF summary range in the current configuration." ::= { ospfCfg 14 } ospfCurCfgRangeEntry OBJECT-TYPE SYNTAX OspfCurCfgRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF summary range." INDEX { ospfCurCfgRangeIndex } ::= { ospfCurCfgRangeTable 1 } OspfCurCfgRangeEntry ::= SEQUENCE { ospfCurCfgRangeIndex Integer32, ospfCurCfgRangeAddr IpAddress, ospfCurCfgRangeMask IpAddress, ospfCurCfgRangeAreaIndex Integer32, ospfCurCfgRangeHideState INTEGER, ospfCurCfgRangeState INTEGER } ospfCurCfgRangeIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The range number for which the OSPF summary range table is related." ::= { ospfCurCfgRangeEntry 1} ospfCurCfgRangeAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the range." ::= { ospfCurCfgRangeEntry 2 } ospfCurCfgRangeMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The mask of the range." ::= { ospfCurCfgRangeEntry 3 } ospfCurCfgRangeAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The area index." ::= { ospfCurCfgRangeEntry 4 } ospfCurCfgRangeHideState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the hide range." ::= { ospfCurCfgRangeEntry 5 } ospfCurCfgRangeState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the range." ::= { ospfCurCfgRangeEntry 6 } ospfNewCfgRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfNewCfgRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF summary range in the new configuration." ::= { ospfCfg 15 } ospfNewCfgRangeEntry OBJECT-TYPE SYNTAX OspfNewCfgRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF summary range." INDEX { ospfNewCfgRangeIndex } ::= { ospfNewCfgRangeTable 1 } OspfNewCfgRangeEntry ::= SEQUENCE { ospfNewCfgRangeIndex Integer32, ospfNewCfgRangeAddr IpAddress, ospfNewCfgRangeMask IpAddress, ospfNewCfgRangeAreaIndex Integer32, ospfNewCfgRangeHideState INTEGER, ospfNewCfgRangeState INTEGER, ospfNewCfgRangeDelete INTEGER } ospfNewCfgRangeIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The range number for which the OSPF summary range table is related." ::= { ospfNewCfgRangeEntry 1} ospfNewCfgRangeAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP Address of the range." ::= { ospfNewCfgRangeEntry 2 } ospfNewCfgRangeMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The mask of the range." ::= { ospfNewCfgRangeEntry 3 } ospfNewCfgRangeAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The area index." ::= { ospfNewCfgRangeEntry 4 } ospfNewCfgRangeHideState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the hide range." ::= { ospfNewCfgRangeEntry 5 } ospfNewCfgRangeState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the range." ::= { ospfNewCfgRangeEntry 6 } ospfNewCfgRangeDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ospfNewCfgRangeEntry 7 } ospfRouteRedistribution OBJECT IDENTIFIER ::= { ospfCfg 4 } ospfRedistributeStatic OBJECT IDENTIFIER ::= { ospfRouteRedistribution 1 } ospfCurCfgStaticMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-only STATUS current DESCRIPTION "The metric to be assigned to static routes." ::= { ospfRedistributeStatic 1 } ospfNewCfgStaticMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "The metric to be assigned to static routes." ::= { ospfRedistributeStatic 2 } ospfCurCfgStaticMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The AS External metric type for static routes." ::= { ospfRedistributeStatic 3 } ospfNewCfgStaticMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The AS External metric type for static routes." ::= { ospfRedistributeStatic 4 } ospfCurCfgStaticOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ospfRedistributeStatic 5 } ospfNewCfgStaticOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ospfRedistributeStatic 6 } ospfNewCfgStaticAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ospfRedistributeStatic 7 } ospfNewCfgStaticRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ospfRedistributeStatic 8 } ospfRedistributeEbgp OBJECT IDENTIFIER ::= { ospfRouteRedistribution 2 } ospfCurCfgEbgpMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-only STATUS current DESCRIPTION "The export metric to be assigned to External BGP routes." ::= { ospfRedistributeEbgp 1 } ospfNewCfgEbgpMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "The export metric to be assigned to External BGP routes." ::= { ospfRedistributeEbgp 2 } ospfCurCfgEbgpMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The AS External metric type for External BGP routes." ::= { ospfRedistributeEbgp 3 } ospfNewCfgEbgpMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The AS External metric type for External BGP routes." ::= { ospfRedistributeEbgp 4 } ospfCurCfgEbgpOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ospfRedistributeEbgp 5 } ospfNewCfgEbgpOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ospfRedistributeEbgp 6 } ospfNewCfgEbgpAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ospfRedistributeEbgp 7 } ospfNewCfgEbgpRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ospfRedistributeEbgp 8 } ospfRedistributeIbgp OBJECT IDENTIFIER ::= { ospfRouteRedistribution 3 } ospfCurCfgIbgpMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-only STATUS current DESCRIPTION "The export metric for Internal BGP routes." ::= { ospfRedistributeIbgp 1 } ospfNewCfgIbgpMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "The export metric for Internal BGP routes." ::= { ospfRedistributeIbgp 2 } ospfCurCfgIbgpMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The AS External metric type for Internal BGP routes." ::= { ospfRedistributeIbgp 3 } ospfNewCfgIbgpMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The AS External metric type for Internal BGP routes." ::= { ospfRedistributeIbgp 4 } ospfCurCfgIbgpOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ospfRedistributeIbgp 5 } ospfNewCfgIbgpOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ospfRedistributeIbgp 6 } ospfNewCfgIbgpAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ospfRedistributeIbgp 7 } ospfNewCfgIbgpRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ospfRedistributeIbgp 8 } ospfRedistributeFixed OBJECT IDENTIFIER ::= { ospfRouteRedistribution 4 } ospfCurCfgFixedMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-only STATUS current DESCRIPTION "The export metric for fixed routes." ::= { ospfRedistributeFixed 1 } ospfNewCfgFixedMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "The export metric for fixed routes." ::= { ospfRedistributeFixed 2 } ospfCurCfgFixedMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The AS External metric type for fixed routes." ::= { ospfRedistributeFixed 3 } ospfNewCfgFixedMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The AS External metric type for fixed routes." ::= { ospfRedistributeFixed 4 } ospfCurCfgFixedOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ospfRedistributeFixed 5 } ospfNewCfgFixedOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ospfRedistributeFixed 6 } ospfNewCfgFixedAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ospfRedistributeFixed 7 } ospfNewCfgFixedRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ospfRedistributeFixed 8 } ospfRedistributeRip OBJECT IDENTIFIER ::= { ospfRouteRedistribution 5 } ospfCurCfgRipMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-only STATUS current DESCRIPTION "The export metric for RIP routes. " ::= { ospfRedistributeRip 1 } ospfNewCfgRipMetric OBJECT-TYPE SYNTAX INTEGER (0..16777214) MAX-ACCESS read-write STATUS current DESCRIPTION "The export metric for RIP routes. " ::= { ospfRedistributeRip 2 } ospfCurCfgRipMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The AS External metric type for RIP routes." ::= { ospfRedistributeRip 3 } ospfNewCfgRipMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The AS External metric type for RIP routes." ::= { ospfRedistributeRip 4 } ospfCurCfgRipOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ospfRedistributeRip 5 } ospfNewCfgRipOutRmapList OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The route maps present in the out route map list. The route maps are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Rmap 9 || || || ||___ Rmap 8 || |____ Rmap 7 || . . . ||_________ Rmap 2 |__________ Rmap 1 where x : 1 - The represented route map is selected 0 - The represented route map is not selected" ::= { ospfRedistributeRip 6 } ospfNewCfgRipAddOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be add into out-rmap list. When read, 0 is returned." ::= { ospfRedistributeRip 7 } ospfNewCfgRipRemoveOutRmap OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The route map to be removed from out-rmap list. When read, 0 is returned." ::= { ospfRedistributeRip 8 } -- -- IP OSPFv3 configuration -- ospf3General OBJECT IDENTIFIER ::= { ospf3Cfg 1 } ospf3IntfTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPFv3 Interface table." ::= { ospf3General 1 } ospf3AreaTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPFv3 Area table." ::= { ospf3General 2 } ospf3RangeTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPFv3 Range table." ::= { ospf3General 3 } ospf3ExtRangeTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPFv3 Summary Prefix table." ::= { ospf3General 4 } ospf3RedistTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPFv3 Redist Config table." ::= { ospf3General 5 } ospf3VirtIntfTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPFv3 Virtual Interface table." ::= { ospf3General 6 } ospf3HostTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPFv3 Host table." ::= { ospf3General 7 } ospf3NbrTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the OSPFv3 Neighbor table." ::= { ospf3General 8 } ospf3CurCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPFv3 global state." ::= { ospf3General 9 } ospf3NewCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Globally turn OSPFv3 on or off." ::= { ospf3General 10 } ospf3CurCfgRouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The router ID." ::= { ospf3General 11 } ospf3NewCfgRouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The router ID." ::= { ospf3General 12 } ospf3CurCfgAbrType OBJECT-TYPE SYNTAX INTEGER { standard(1), cisco(2), ibm(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPFv3 alternative ABR type." ::= { ospf3General 13 } ospf3NewCfgAbrType OBJECT-TYPE SYNTAX INTEGER { standard(1), cisco(2), ibm(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set the OSPFv3 alternative ABR type." ::= { ospf3General 14 } ospf3CurCfgLSDB OBJECT-TYPE SYNTAX INTEGER (-1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The LSDB limit for external LSA." ::= { ospf3General 15 } ospf3NewCfgLSDB OBJECT-TYPE SYNTAX INTEGER (-1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Set the LSDB limit for external LSA, -1 for none." ::= { ospf3General 16 } ospf3CurCfgExitOverflow OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The exit overflow interval in seconds." ::= { ospf3General 17 } ospf3NewCfgExitOverflow OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "Set the exit overflow interval in seconds." ::= { ospf3General 18 } ospf3CurCfgReferenceBw OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The reference bandwidth for default interface metric calculation." ::= { ospf3General 19 } ospf3NewCfgReferenceBw OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The reference bandwidth for default interface metric calculation." ::= { ospf3General 20 } ospf3CurCfgSpfDelay OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The delay between topology change and SPF calculation." ::= { ospf3General 21 } ospf3NewCfgSpfDelay OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The delay between topology change and SPF calculation." ::= { ospf3General 22 } ospf3CurCfgSpfHold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The hold time between two consecutive SPF calculation." ::= { ospf3General 23 } ospf3NewCfgSpfHold OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The hold time between two consecutive SPF calculation." ::= { ospf3General 24 } ospf3CurCfgNssaAsbrDfRtTrans OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPFv3 state of setting P-bit by an NSSA internal ASBR." ::= { ospf3General 29 } ospf3NewCfgNssaAsbrDfRtTrans OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "OSPFv3 state of setting P-bit by an NSSA internal ASBR." ::= { ospf3General 30 } ospf3CurCfgAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3CurCfgAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 area in the current configuration block." ::= { ospf3Cfg 2 } ospf3CurCfgAreaEntry OBJECT-TYPE SYNTAX Ospf3CurCfgAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPFv3 area." INDEX { ospf3CurCfgAreaIndex } ::= { ospf3CurCfgAreaTable 1 } Ospf3CurCfgAreaEntry ::= SEQUENCE { ospf3CurCfgAreaIndex Integer32, ospf3CurCfgAreaId IpAddress, ospf3CurCfgAreaStbInterval INTEGER, ospf3CurCfgAreaType INTEGER, ospf3CurCfgAreaNoSumm INTEGER, ospf3CurCfgAreaDefaultMetric INTEGER, ospf3CurCfgAreaDefaultMetricType INTEGER, ospf3CurCfgAreaTranslRole INTEGER, ospf3CurCfgAreaStatus INTEGER } ospf3CurCfgAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 area number for which the OSPFv3 area table is related." ::= { ospf3CurCfgAreaEntry 1} ospf3CurCfgAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the OSPFv3 area." ::= { ospf3CurCfgAreaEntry 2 } ospf3CurCfgAreaStbInterval OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The stability interval for the NSSA area" ::= { ospf3CurCfgAreaEntry 3 } ospf3CurCfgAreaType OBJECT-TYPE SYNTAX INTEGER { transit(1), stub(2), nssa(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of Area. transit(1) stub(2) nssa(3)" ::= { ospf3CurCfgAreaEntry 4 } ospf3CurCfgAreaNoSumm OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status disabled(0) enabled(1)" ::= { ospf3CurCfgAreaEntry 5 } ospf3CurCfgAreaDefaultMetric OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-only STATUS current DESCRIPTION "Metric for stub/NSSA area (1-16777215)" ::= { ospf3CurCfgAreaEntry 6 } ospf3CurCfgAreaDefaultMetricType OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-only STATUS current DESCRIPTION "Metric Type for stub/NSSA area (1-3)" ::= { ospf3CurCfgAreaEntry 7 } ospf3CurCfgAreaTranslRole OBJECT-TYPE SYNTAX INTEGER { always(1), candidate(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Translation role for the NSSA area. always(1) candidate(2)" ::= { ospf3CurCfgAreaEntry 8 } ospf3CurCfgAreaStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status disabled(0) enabled(1)" ::= { ospf3CurCfgAreaEntry 9 } ospf3NewCfgAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3NewCfgAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Area configuration in the new configuration block." ::= { ospf3Cfg 3 } ospf3NewCfgAreaEntry OBJECT-TYPE SYNTAX Ospf3NewCfgAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPFv3 area." INDEX { ospf3NewCfgAreaIndex } ::= { ospf3NewCfgAreaTable 1 } Ospf3NewCfgAreaEntry ::= SEQUENCE { ospf3NewCfgAreaIndex Integer32, ospf3NewCfgAreaId IpAddress, ospf3NewCfgAreaStbInterval INTEGER, ospf3NewCfgAreaType INTEGER, ospf3NewCfgAreaNoSumm INTEGER, ospf3NewCfgAreaDefaultMetric INTEGER, ospf3NewCfgAreaDefaultMetricType INTEGER, ospf3NewCfgAreaTranslRole INTEGER, ospf3NewCfgAreaStatus INTEGER, ospf3NewCfgAreaDelete INTEGER } ospf3NewCfgAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 area number for which the OSPFv3 area table is related." ::= { ospf3NewCfgAreaEntry 1} ospf3NewCfgAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP Address of the OSPFv3 area." ::= { ospf3NewCfgAreaEntry 2 } ospf3NewCfgAreaStbInterval OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The Stability interval for the NSSA area." ::= { ospf3NewCfgAreaEntry 3 } ospf3NewCfgAreaType OBJECT-TYPE SYNTAX INTEGER { transit(1), stub(2), nssa(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of Area. transit(1) stub(2) nssa(3)" ::= { ospf3NewCfgAreaEntry 4 } ospf3NewCfgAreaNoSumm OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Status disabled(0) enabled(1)" ::= { ospf3NewCfgAreaEntry 5 } ospf3NewCfgAreaDefaultMetric OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-create STATUS current DESCRIPTION "Metric for stub/NSSA area (1-16777215)" ::= { ospf3NewCfgAreaEntry 6 } ospf3NewCfgAreaDefaultMetricType OBJECT-TYPE SYNTAX INTEGER (1..3) MAX-ACCESS read-create STATUS current DESCRIPTION "Metric Type for stub/NSSA area (1-3)" ::= { ospf3NewCfgAreaEntry 7 } ospf3NewCfgAreaTranslRole OBJECT-TYPE SYNTAX INTEGER { always(1), candidate(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Translation role for the NSSA area. always(1) candidate(2)" ::= { ospf3NewCfgAreaEntry 8 } ospf3NewCfgAreaStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Status disabled(0) enabled(1)" ::= { ospf3NewCfgAreaEntry 9 } ospf3NewCfgAreaDelete OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete the area no(0), yes(1)" ::= { ospf3NewCfgAreaEntry 10 } -- OSPFv3 Host Table ospf3CurCfgHostTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3CurCfgHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Host configuration." ::= { ospf3Cfg 4 } ospf3CurCfgHostEntry OBJECT-TYPE SYNTAX Ospf3CurCfgHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPFv3 host." INDEX { ospf3CurCfgHostIndex } ::= { ospf3CurCfgHostTable 1 } Ospf3CurCfgHostEntry ::= SEQUENCE { ospf3CurCfgHostIndex Integer32, ospf3CurCfgHostIpAddr DisplayString, ospf3CurCfgHostAreaIndex Integer32, ospf3CurCfgHostCost INTEGER, ospf3CurCfgHostState INTEGER } ospf3CurCfgHostIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 host number for which the OSPFv3 host table is related." ::= { ospf3CurCfgHostEntry 1} ospf3CurCfgHostIpAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 Address of the OSPFv3 host." ::= { ospf3CurCfgHostEntry 2 } ospf3CurCfgHostAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The area index." ::= { ospf3CurCfgHostEntry 3 } ospf3CurCfgHostCost OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the OSPFv3 host." ::= { ospf3CurCfgHostEntry 4 } ospf3CurCfgHostState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable an OSPFv3 Host" ::= { ospf3CurCfgHostEntry 5 } ospf3NewCfgHostTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3NewCfgHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Host configuration." ::= { ospf3Cfg 5 } ospf3NewCfgHostEntry OBJECT-TYPE SYNTAX Ospf3NewCfgHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPFv3 host." INDEX { ospf3NewCfgHostIndex } ::= { ospf3NewCfgHostTable 1 } Ospf3NewCfgHostEntry ::= SEQUENCE { ospf3NewCfgHostIndex Integer32, ospf3NewCfgHostIpAddr DisplayString, ospf3NewCfgHostAreaIndex Integer32, ospf3NewCfgHostCost INTEGER, ospf3NewCfgHostState INTEGER, ospf3NewCfgHostDelete INTEGER } ospf3NewCfgHostIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 host number for which the OSPFv3 host table is related." ::= { ospf3NewCfgHostEntry 1} ospf3NewCfgHostIpAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "The IP6 Address of the OSPFv3 host. Address should be 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx or ::xxxx" ::= { ospf3NewCfgHostEntry 2 } ospf3NewCfgHostAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The OSPFv3 area index." ::= { ospf3NewCfgHostEntry 3 } ospf3NewCfgHostCost OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The cost of the OSPFv3 host." ::= { ospf3NewCfgHostEntry 4 } ospf3NewCfgHostState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable an OSPFv3 Host" ::= { ospf3NewCfgHostEntry 5 } ospf3NewCfgHostDelete OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete the OSPFv3 host: no(0), yes(1)" ::= { ospf3NewCfgHostEntry 6 } -- OSPFv3 Neighbor Table ospf3CurCfgNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3CurCfgNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Neighbor configuration." ::= { ospf3Cfg 6 } ospf3CurCfgNbrEntry OBJECT-TYPE SYNTAX Ospf3CurCfgNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPFv3 neighbor." INDEX { ospf3CurCfgNbrIndex } ::= { ospf3CurCfgNbrTable 1 } Ospf3CurCfgNbrEntry ::= SEQUENCE { ospf3CurCfgNbrIndex Integer32, ospf3CurCfgNbrIpAddr DisplayString, ospf3CurCfgNbrIntfIndex Integer32, ospf3CurCfgNbrPriority INTEGER, ospf3CurCfgNbrState INTEGER } ospf3CurCfgNbrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 neighbor number for which the OSPFv3 neighbor table is related." ::= { ospf3CurCfgNbrEntry 1} ospf3CurCfgNbrIpAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 Address of the OSPFv3 neighbor." ::= { ospf3CurCfgNbrEntry 2 } ospf3CurCfgNbrIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index." ::= { ospf3CurCfgNbrEntry 3 } ospf3CurCfgNbrPriority OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The priority of the OSPFv3 neighbor." ::= { ospf3CurCfgNbrEntry 4 } ospf3CurCfgNbrState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable an OSPFv3 neighbor" ::= { ospf3CurCfgNbrEntry 5 } ospf3NewCfgNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3NewCfgNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Neighbor configuration." ::= { ospf3Cfg 7 } ospf3NewCfgNbrEntry OBJECT-TYPE SYNTAX Ospf3NewCfgNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPFv3 neighbor." INDEX { ospf3NewCfgNbrIndex } ::= { ospf3NewCfgNbrTable 1 } Ospf3NewCfgNbrEntry ::= SEQUENCE { ospf3NewCfgNbrIndex Integer32, ospf3NewCfgNbrIpAddr DisplayString, ospf3NewCfgNbrIntfIndex Integer32, ospf3NewCfgNbrPriority INTEGER, ospf3NewCfgNbrState INTEGER, ospf3NewCfgNbrDelete INTEGER } ospf3NewCfgNbrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 neighbor number for which the OSPFv3 neighbor table is related." ::= { ospf3NewCfgNbrEntry 1} ospf3NewCfgNbrIpAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "The IP6 Address of the OSPFv3 neighbor. Address should be 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx or ::xxxx" ::= { ospf3NewCfgNbrEntry 2 } ospf3NewCfgNbrIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The OSPFv3 interface index." ::= { ospf3NewCfgNbrEntry 3 } ospf3NewCfgNbrPriority OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The cost of the OSPFv3 neighbor." ::= { ospf3NewCfgNbrEntry 4 } ospf3NewCfgNbrState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable or disable an OSPFv3 Neighbor" ::= { ospf3NewCfgNbrEntry 5 } ospf3NewCfgNbrDelete OBJECT-TYPE SYNTAX INTEGER { no(0), yes(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete the OSPFv3 neighbor: no(0), yes(1)" ::= { ospf3NewCfgNbrEntry 6 } ospf3CurCfgIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3CurCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Interface in the current configuration block." ::= { ospf3Cfg 8 } ospf3CurCfgIntfEntry OBJECT-TYPE SYNTAX Ospf3CurCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPFv3 Interface." INDEX { ospf3CurCfgIntfIndex } ::= { ospf3CurCfgIntfTable 1 } Ospf3CurCfgIntfEntry ::= SEQUENCE { ospf3CurCfgIntfIndex Integer32, ospf3CurCfgIntfInstId INTEGER, ospf3CurCfgIntfArea INTEGER, ospf3CurCfgIntfCost INTEGER, ospf3CurCfgIntfPrio INTEGER, ospf3CurCfgIntfHello INTEGER, ospf3CurCfgIntfDead INTEGER, ospf3CurCfgIntfPoll Unsigned32, ospf3CurCfgIntfTrans INTEGER, ospf3CurCfgIntfRetra INTEGER, ospf3CurCfgIntfPassive INTEGER, ospf3CurCfgIntfNetworkType INTEGER, ospf3CurCfgIntfStatus INTEGER , ospf3CurCfgIntfAuthSpi Unsigned32, ospf3CurCfgIntfAuthEnable INTEGER, ospf3CurCfgIntfAuthType INTEGER, ospf3CurCfgIntfAuthKey OCTET STRING, ospf3CurCfgIntfEncrySpi Unsigned32, ospf3CurCfgIntfEncryEnable INTEGER, ospf3CurCfgIntfEncryType INTEGER, ospf3CurCfgIntfEncryKey OCTET STRING, ospf3CurCfgIntfEncryAuthType INTEGER, ospf3CurCfgIntfEncryAuthKey OCTET STRING , ospf3CurCfgIntfLsaSupress INTEGER } ospf3CurCfgIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 Interface number for which the OSPFv3 Interface table is related." ::= { ospf3CurCfgIntfEntry 1} ospf3CurCfgIntfInstId OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface Instance Id" ::= { ospf3CurCfgIntfEntry 2 } ospf3CurCfgIntfArea OBJECT-TYPE SYNTAX INTEGER (0..2) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the area that the interface belongs" ::= { ospf3CurCfgIntfEntry 3 } ospf3CurCfgIntfCost OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface cost" ::= { ospf3CurCfgIntfEntry 4 } ospf3CurCfgIntfPrio OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface router priority" ::= { ospf3CurCfgIntfEntry 5 } ospf3CurCfgIntfHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Hello interval" ::= { ospf3CurCfgIntfEntry 6 } ospf3CurCfgIntfDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Dead interval" ::= { ospf3CurCfgIntfEntry 7 } ospf3CurCfgIntfPoll OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "Poll interval(1..4294967295)" ::= { ospf3CurCfgIntfEntry 8 } ospf3CurCfgIntfTrans OBJECT-TYPE SYNTAX INTEGER (1..1800) MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit delay" ::= { ospf3CurCfgIntfEntry 9 } ospf3CurCfgIntfRetra OBJECT-TYPE SYNTAX INTEGER (1..1800) MAX-ACCESS read-only STATUS current DESCRIPTION "Retransmit interval" ::= { ospf3CurCfgIntfEntry 10 } ospf3CurCfgIntfPassive OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Passive interface disabled(0), enabled(1)" ::= { ospf3CurCfgIntfEntry 11 } ospf3CurCfgIntfNetworkType OBJECT-TYPE SYNTAX INTEGER { broadcast(1), non-broadcast(2), point-to-point(3), point-to-multipoint(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Network Type. broadcast(1), non-broadcast(2), point-to-point(3), point-to-multipoint(4)" ::= { ospf3CurCfgIntfEntry 12 } ospf3CurCfgIntfStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of the interface disabled(0), enabled(1)" ::= { ospf3CurCfgIntfEntry 16 } ospf3CurCfgIntfAuthSpi OBJECT-TYPE SYNTAX Unsigned32 (256..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "Spi Id(256 - 4294967295)" ::= { ospf3CurCfgIntfEntry 17 } ospf3CurCfgIntfAuthEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status disabled(0), enabled(1)" ::= { ospf3CurCfgIntfEntry 18 } ospf3CurCfgIntfAuthType OBJECT-TYPE SYNTAX INTEGER { none(0), md5(2), sha1(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Authentication Type none(0), md5(2), sha1(1)" ::= { ospf3CurCfgIntfEntry 19 } ospf3CurCfgIntfAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "Authentication Key Hex-string MD5 key - 32 chars (128 bits) Hex-string SHA-1 key - 40 chars (160 bits)" ::= { ospf3CurCfgIntfEntry 20 } ospf3CurCfgIntfEncrySpi OBJECT-TYPE SYNTAX Unsigned32 (256..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "Spi Id(256 - 4294967295)" ::= { ospf3CurCfgIntfEntry 21 } ospf3CurCfgIntfEncryEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status disabled(0), enabled(1)" ::= { ospf3CurCfgIntfEntry 22 } ospf3CurCfgIntfEncryType OBJECT-TYPE SYNTAX INTEGER { null(0), tripledes(2), aes(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Encryption Type null(0), 3des(2), aes(3)" ::= { ospf3CurCfgIntfEntry 23 } ospf3CurCfgIntfEncryKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "Encryption Key Hex-string AES key - 32 chars (128 bits) Hex-string 3DES key - 48 chars (192 bits)" ::= { ospf3CurCfgIntfEntry 24 } ospf3CurCfgIntfEncryAuthType OBJECT-TYPE SYNTAX INTEGER { none(0), md5(2), sha1(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Encryption Authentication Type none(0), md5(2), sha1(1)" ::= { ospf3CurCfgIntfEntry 25 } ospf3CurCfgIntfEncryAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "Encryption Authentication Key Hex-string MD5 key - 32 chars (128 bits) Hex-string SHA-1 key - 40 chars (160 bits)" ::= { ospf3CurCfgIntfEntry 26 } ospf3CurCfgIntfLsaSupress OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "LSA Supression on interface disabled(0), enabled(1)" ::= { ospf3CurCfgIntfEntry 27 } ospf3NewCfgIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3NewCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 interface in the new configuration block." ::= { ospf3Cfg 9 } ospf3NewCfgIntfEntry OBJECT-TYPE SYNTAX Ospf3NewCfgIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPFv3 interface." INDEX { ospf3NewCfgIntfIndex } ::= { ospf3NewCfgIntfTable 1 } Ospf3NewCfgIntfEntry ::= SEQUENCE { ospf3NewCfgIntfIndex Integer32, ospf3NewCfgIntfInstId INTEGER, ospf3NewCfgIntfArea INTEGER, ospf3NewCfgIntfCost INTEGER, ospf3NewCfgIntfPrio INTEGER, ospf3NewCfgIntfHello INTEGER, ospf3NewCfgIntfPoll Unsigned32, ospf3NewCfgIntfDead INTEGER, ospf3NewCfgIntfTrans INTEGER, ospf3NewCfgIntfRetra INTEGER, ospf3NewCfgIntfPassive INTEGER, ospf3NewCfgIntfNetworkType INTEGER, ospf3NewCfgIntfStatus INTEGER, ospf3NewCfgIntfDelete INTEGER , ospf3NewCfgIntfAuthSpi Unsigned32, ospf3NewCfgIntfAuthEnable INTEGER, ospf3NewCfgIntfAuthType INTEGER, ospf3NewCfgIntfAuthKey OCTET STRING, ospf3NewCfgIntfAuthReset INTEGER, ospf3NewCfgIntfEncrySpi Unsigned32, ospf3NewCfgIntfEncryEnable INTEGER, ospf3NewCfgIntfEncryType INTEGER, ospf3NewCfgIntfEncryKey OCTET STRING, ospf3NewCfgIntfEncryAuthType INTEGER, ospf3NewCfgIntfEncryAuthKey OCTET STRING, ospf3NewCfgIntfEncryReset INTEGER , ospf3NewCfgIntfLsaSupress INTEGER } ospf3NewCfgIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 Interface number for which the OSPFv3 Interface table is related." ::= { ospf3NewCfgIntfEntry 1} ospf3NewCfgIntfInstId OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Interface Instance Id (0..255)" ::= { ospf3NewCfgIntfEntry 2 } ospf3NewCfgIntfArea OBJECT-TYPE SYNTAX INTEGER (0..2) MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the area that the interface belongs (0..2)" ::= { ospf3NewCfgIntfEntry 3 } ospf3NewCfgIntfCost OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Interface cost(1..65535) and 0 for none" ::= { ospf3NewCfgIntfEntry 4 } ospf3NewCfgIntfPrio OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Interface router priority(0..255)" ::= { ospf3NewCfgIntfEntry 5 } ospf3NewCfgIntfHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Hello interval(1..65535)" ::= { ospf3NewCfgIntfEntry 6 } ospf3NewCfgIntfDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Dead interval(1..65535)" ::= { ospf3NewCfgIntfEntry 7 } ospf3NewCfgIntfPoll OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "Poll interval(1..4294967295)" ::= { ospf3NewCfgIntfEntry 8 } ospf3NewCfgIntfTrans OBJECT-TYPE SYNTAX INTEGER (1..1800) MAX-ACCESS read-create STATUS current DESCRIPTION "Transmit delay(1..1800)" ::= { ospf3NewCfgIntfEntry 9 } ospf3NewCfgIntfRetra OBJECT-TYPE SYNTAX INTEGER (1..1800) MAX-ACCESS read-create STATUS current DESCRIPTION "Retransmit interval(1..1800)" ::= { ospf3NewCfgIntfEntry 10 } ospf3NewCfgIntfPassive OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Passive interface disabled(0), enabled(1)" ::= { ospf3NewCfgIntfEntry 11 } ospf3NewCfgIntfNetworkType OBJECT-TYPE SYNTAX INTEGER { broadcast(1), non-broadcast(2), point-to-point(3), point-to-multipoint(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Network Type. broadcast(1), non-broadcast(2), point-to-point(3), point-to-multipoint(4)" ::= { ospf3NewCfgIntfEntry 12 } ospf3NewCfgIntfStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Status of the interface disabled(0), enabled(1)" ::= { ospf3NewCfgIntfEntry 16 } ospf3NewCfgIntfDelete OBJECT-TYPE SYNTAX INTEGER { other(0), delete(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete the interface other(0), delete(1)" ::= { ospf3NewCfgIntfEntry 17 } ospf3NewCfgIntfAuthSpi OBJECT-TYPE SYNTAX Unsigned32 (256..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication Spi Id(256 - 4294967295)" ::= { ospf3NewCfgIntfEntry 18 } ospf3NewCfgIntfAuthEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication Status disabled(0), enabled(1)" ::= { ospf3NewCfgIntfEntry 19 } ospf3NewCfgIntfAuthType OBJECT-TYPE SYNTAX INTEGER { none(0), md5(2), sha1(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication Type none(0), md5(2), sha1(1)" ::= { ospf3NewCfgIntfEntry 20 } ospf3NewCfgIntfAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication Type Hex-string MD5 key - 32 chars (128 bits), Hex-string SHA-1 key - 40 chars (160 bits)" ::= { ospf3NewCfgIntfEntry 21 } ospf3NewCfgIntfAuthReset OBJECT-TYPE SYNTAX INTEGER { other(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Reset AH configuration other(0), reset(1)" ::= { ospf3NewCfgIntfEntry 22 } ospf3NewCfgIntfEncrySpi OBJECT-TYPE SYNTAX Unsigned32 (256..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "Encryption Spi Id(256 - 4294967295)" ::= { ospf3NewCfgIntfEntry 23 } ospf3NewCfgIntfEncryEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Encryption Status disabled(0), enabled(1)" ::= { ospf3NewCfgIntfEntry 24 } ospf3NewCfgIntfEncryType OBJECT-TYPE SYNTAX INTEGER { null(0), tripledes(2), aes(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Encryption Type null(0), 3des(2), aes(3)" ::= { ospf3NewCfgIntfEntry 25 } ospf3NewCfgIntfEncryKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4..48)) MAX-ACCESS read-write STATUS current DESCRIPTION "Encryption Key Hex-string AES key - 32 chars (128 bits) Hex-string 3DES key - 48 chars (192 bits)" ::= { ospf3NewCfgIntfEntry 26 } ospf3NewCfgIntfEncryAuthType OBJECT-TYPE SYNTAX INTEGER { none(0), md5(2), sha1(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Encryption Authentication Type none(0), md5(2), sha1(1)" ::= { ospf3NewCfgIntfEntry 27 } ospf3NewCfgIntfEncryAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "Encryption Authentication Key Hex-string MD5 key - 32 chars (128 bits), Hex-string SHA-1 key - 40 chars (160 bits)" ::= { ospf3NewCfgIntfEntry 28 } ospf3NewCfgIntfEncryReset OBJECT-TYPE SYNTAX INTEGER { other(0), reset(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Reset Encryption configuration other(0), reset(1)" ::= { ospf3NewCfgIntfEntry 29 } ospf3NewCfgIntfLsaSupress OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "LSA Supression on interface disabled(0), enabled(1)" ::= { ospf3NewCfgIntfEntry 30 } ospf3CurCfgVirtIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3CurCfgVirtIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Virtual Interface configuration in the current configuration." ::= { ospf3Cfg 10 } ospf3CurCfgVirtIntfEntry OBJECT-TYPE SYNTAX Ospf3CurCfgVirtIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPFv3v3 virtual Interface." INDEX { ospf3CurCfgVirtIntfIndex } ::= { ospf3CurCfgVirtIntfTable 1 } Ospf3CurCfgVirtIntfEntry ::= SEQUENCE { ospf3CurCfgVirtIntfIndex Integer32, ospf3CurCfgVirtIntfAreaId INTEGER, ospf3CurCfgVirtIntfNbr IpAddress, ospf3CurCfgVirtIntfHello INTEGER, ospf3CurCfgVirtIntfDead INTEGER, ospf3CurCfgVirtIntfTrans INTEGER, ospf3CurCfgVirtIntfRetra INTEGER, ospf3CurCfgVirtIntfStatus INTEGER } ospf3CurCfgVirtIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 Virtual Interface number for which the OSPFv3 Virtual Interface table is related." ::= { ospf3CurCfgVirtIntfEntry 1} ospf3CurCfgVirtIntfAreaId OBJECT-TYPE SYNTAX INTEGER (0..2) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the OSPFv3 area to which this virtual interface belongs." ::= { ospf3CurCfgVirtIntfEntry 3 } ospf3CurCfgVirtIntfNbr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the OSPFv3 neighbor for this virtual interface." ::= { ospf3CurCfgVirtIntfEntry 4 } ospf3CurCfgVirtIntfHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Hello interval" ::= { ospf3CurCfgVirtIntfEntry 5 } ospf3CurCfgVirtIntfDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Dead interval" ::= { ospf3CurCfgVirtIntfEntry 6 } ospf3CurCfgVirtIntfTrans OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit delay" ::= { ospf3CurCfgVirtIntfEntry 7 } ospf3CurCfgVirtIntfRetra OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "Retransmit interval" ::= { ospf3CurCfgVirtIntfEntry 8 } ospf3CurCfgVirtIntfStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status disabled(0), enabled(1)" ::= { ospf3CurCfgVirtIntfEntry 9 } ospf3NewCfgVirtIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3NewCfgVirtIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Virtual interface in the new configuration block." ::= { ospf3Cfg 11 } ospf3NewCfgVirtIntfEntry OBJECT-TYPE SYNTAX Ospf3NewCfgVirtIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPFv3 virtual interface." INDEX { ospf3NewCfgVirtIntfIndex } ::= { ospf3NewCfgVirtIntfTable 1 } Ospf3NewCfgVirtIntfEntry ::= SEQUENCE { ospf3NewCfgVirtIntfIndex Integer32, ospf3NewCfgVirtIntfAreaId INTEGER, ospf3NewCfgVirtIntfNbr IpAddress, ospf3NewCfgVirtIntfHello INTEGER, ospf3NewCfgVirtIntfDead INTEGER, ospf3NewCfgVirtIntfTrans INTEGER, ospf3NewCfgVirtIntfRetra INTEGER, ospf3NewCfgVirtIntfStatus INTEGER, ospf3NewCfgVirtIntfDelete INTEGER } ospf3NewCfgVirtIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 Virtual Interface number for which the OSPFv3 Virtual Interface table is related." ::= { ospf3NewCfgVirtIntfEntry 1} ospf3NewCfgVirtIntfAreaId OBJECT-TYPE SYNTAX INTEGER (0..2) MAX-ACCESS read-create STATUS current DESCRIPTION "The index of the OSPFv3 area to which this virtual interface belongs." ::= { ospf3NewCfgVirtIntfEntry 3 } ospf3NewCfgVirtIntfNbr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP Address of the OSPFv3 neighbor for this virtual interface." ::= { ospf3NewCfgVirtIntfEntry 4 } ospf3NewCfgVirtIntfHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Hello interval(1..65535)" ::= { ospf3NewCfgVirtIntfEntry 5 } ospf3NewCfgVirtIntfDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "Dead interval(1..65535)" ::= { ospf3NewCfgVirtIntfEntry 6 } ospf3NewCfgVirtIntfTrans OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-create STATUS current DESCRIPTION "Transmit delay(1..3600)" ::= { ospf3NewCfgVirtIntfEntry 7 } ospf3NewCfgVirtIntfRetra OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-create STATUS current DESCRIPTION "Retransmit interval(1..3600)" ::= { ospf3NewCfgVirtIntfEntry 8 } ospf3NewCfgVirtIntfStatus OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Status disabled(0), enabled(1) " ::= { ospf3NewCfgVirtIntfEntry 9 } ospf3NewCfgVirtIntfDelete OBJECT-TYPE SYNTAX INTEGER { other(0), delete(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete other(0), delete(1)" ::= { ospf3NewCfgVirtIntfEntry 10} -- ospfv3 range ospf3CurCfgRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3CurCfgRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 summary range in the current configuration." ::= { ospf3Cfg 12 } ospf3CurCfgRangeEntry OBJECT-TYPE SYNTAX Ospf3CurCfgRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPFv3 summary range." INDEX { ospf3CurCfgRangeIndex } ::= { ospf3CurCfgRangeTable 1 } Ospf3CurCfgRangeEntry ::= SEQUENCE { ospf3CurCfgRangeIndex Integer32, ospf3CurCfgRangeAddr DisplayString, ospf3CurCfgRangePrefixLen INTEGER, ospf3CurCfgRangeAreaIndex Integer32, ospf3CurCfgRangeHideState INTEGER, ospf3CurCfgRangeLsaType INTEGER, ospf3CurCfgRangeRouteTag Unsigned32, ospf3CurCfgRangeState INTEGER } ospf3CurCfgRangeIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The range number for which the OSPFv3 summary range table is related." ::= { ospf3CurCfgRangeEntry 1} ospf3CurCfgRangeAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 Address of the range." ::= { ospf3CurCfgRangeEntry 2 } ospf3CurCfgRangePrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The prefix length of the range." ::= { ospf3CurCfgRangeEntry 3 } ospf3CurCfgRangeAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The area index." ::= { ospf3CurCfgRangeEntry 4 } ospf3CurCfgRangeHideState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the hide range." ::= { ospf3CurCfgRangeEntry 5 } ospf3CurCfgRangeLsaType OBJECT-TYPE SYNTAX INTEGER { summary(8195), type7(8199) } MAX-ACCESS read-only STATUS current DESCRIPTION "The LSA type for aggregation. summary(8195), type7(8199)" ::= { ospf3CurCfgRangeEntry 6 } ospf3CurCfgRangeRouteTag OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The route tag of the range." ::= { ospf3CurCfgRangeEntry 7 } ospf3CurCfgRangeState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the range." ::= { ospf3CurCfgRangeEntry 8 } ospf3NewCfgRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3NewCfgRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 summary range in the new configuration." ::= { ospf3Cfg 13 } ospf3NewCfgRangeEntry OBJECT-TYPE SYNTAX Ospf3NewCfgRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPFv3 summary range." INDEX { ospf3NewCfgRangeIndex } ::= { ospf3NewCfgRangeTable 1 } Ospf3NewCfgRangeEntry ::= SEQUENCE { ospf3NewCfgRangeIndex Integer32, ospf3NewCfgRangeAddr DisplayString, ospf3NewCfgRangePrefixLen INTEGER, ospf3NewCfgRangeAreaIndex Integer32, ospf3NewCfgRangeHideState INTEGER, ospf3NewCfgRangeLsaType INTEGER, ospf3NewCfgRangeRouteTag Unsigned32, ospf3NewCfgRangeState INTEGER, ospf3NewCfgRangeDelete INTEGER } ospf3NewCfgRangeIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The range number for which the OSPFv3 summary range table is related." ::= { ospf3NewCfgRangeEntry 1} ospf3NewCfgRangeAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "The IPv6 Address of the range. Address should be 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx or ::xxxx" ::= { ospf3NewCfgRangeEntry 2 } ospf3NewCfgRangePrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The prefix length of the range." ::= { ospf3NewCfgRangeEntry 3 } ospf3NewCfgRangeAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The area index." ::= { ospf3NewCfgRangeEntry 4 } ospf3NewCfgRangeHideState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the hide range." ::= { ospf3NewCfgRangeEntry 5 } ospf3NewCfgRangeLsaType OBJECT-TYPE SYNTAX INTEGER { summary(8195), type7(8199) } MAX-ACCESS read-create STATUS current DESCRIPTION "The LSA type for aggregation. summary(8195), type7(8199)" ::= { ospf3NewCfgRangeEntry 6 } ospf3NewCfgRangeRouteTag OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The route tag of the range." ::= { ospf3NewCfgRangeEntry 7 } ospf3NewCfgRangeState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the range." ::= { ospf3NewCfgRangeEntry 8 } ospf3NewCfgRangeDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ospf3NewCfgRangeEntry 9 } -- ospfv3 summary prefix ospf3CurCfgExtRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3CurCfgExtRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 AS-External range in the current configuration." ::= { ospf3Cfg 14 } ospf3CurCfgExtRangeEntry OBJECT-TYPE SYNTAX Ospf3CurCfgExtRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPFv3 AS-External range." INDEX { ospf3CurCfgExtRangeIndex } ::= { ospf3CurCfgExtRangeTable 1 } Ospf3CurCfgExtRangeEntry ::= SEQUENCE { ospf3CurCfgExtRangeIndex Integer32, ospf3CurCfgExtRangeAddr DisplayString, ospf3CurCfgExtRangePrefixLen INTEGER, ospf3CurCfgExtRangeAreaIndex Integer32, ospf3CurCfgExtRangeTranslation INTEGER, ospf3CurCfgExtRangeAggrEffect INTEGER, ospf3CurCfgExtRangeState INTEGER } ospf3CurCfgExtRangeIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The range number for which the OSPFv3 AS-External range table is related." ::= { ospf3CurCfgExtRangeEntry 1} ospf3CurCfgExtRangeAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 Address of the AS-External range." ::= { ospf3CurCfgExtRangeEntry 2 } ospf3CurCfgExtRangePrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The prefix length of the AS-External range." ::= { ospf3CurCfgExtRangeEntry 3 } ospf3CurCfgExtRangeAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The area index." ::= { ospf3CurCfgExtRangeEntry 4 } ospf3CurCfgExtRangeTranslation OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the setting the P-bit in the generated LSA." ::= { ospf3CurCfgExtRangeEntry 5 } ospf3CurCfgExtRangeAggrEffect OBJECT-TYPE SYNTAX INTEGER { advertise(1), not-advertise(2), allowAll(3), denyAll(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The aggregation effect. advertise(1), not-advertise(2), allowAll(3), denyAll(4)" ::= { ospf3CurCfgExtRangeEntry 6 } ospf3CurCfgExtRangeState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the AS-External range." ::= { ospf3CurCfgExtRangeEntry 7 } ospf3NewCfgExtRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3NewCfgExtRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 summary AS-External range in the new configuration." ::= { ospf3Cfg 15 } ospf3NewCfgExtRangeEntry OBJECT-TYPE SYNTAX Ospf3NewCfgExtRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPFv3 summary AS-External range." INDEX { ospf3NewCfgExtRangeIndex } ::= { ospf3NewCfgExtRangeTable 1 } Ospf3NewCfgExtRangeEntry ::= SEQUENCE { ospf3NewCfgExtRangeIndex Integer32, ospf3NewCfgExtRangeAddr DisplayString, ospf3NewCfgExtRangePrefixLen INTEGER, ospf3NewCfgExtRangeAreaIndex Integer32, ospf3NewCfgExtRangeTranslation INTEGER, ospf3NewCfgExtRangeAggrEffect INTEGER, ospf3NewCfgExtRangeState INTEGER, ospf3NewCfgExtRangeDelete INTEGER } ospf3NewCfgExtRangeIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The range number for which the OSPFv3 AS-External range table is related." ::= { ospf3NewCfgExtRangeEntry 1} ospf3NewCfgExtRangeAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "The IPv6 Address of the AS-External range. Address should be 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx or ::xxxx" ::= { ospf3NewCfgExtRangeEntry 2 } ospf3NewCfgExtRangePrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The prefix length of the AS-External range." ::= { ospf3NewCfgExtRangeEntry 3 } ospf3NewCfgExtRangeAreaIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The area index." ::= { ospf3NewCfgExtRangeEntry 4 } ospf3NewCfgExtRangeTranslation OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the setting the P-bit in the generated LSA." ::= { ospf3NewCfgExtRangeEntry 5 } ospf3NewCfgExtRangeAggrEffect OBJECT-TYPE SYNTAX INTEGER { advertise(1), not-advertise(2), allowAll(3), denyAll(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The aggregation effect. advertise(1), not-advertise(2), allowAll(3), denyAll(4)" ::= { ospf3NewCfgExtRangeEntry 6 } ospf3NewCfgExtRangeState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the AS-External range." ::= { ospf3NewCfgExtRangeEntry 7 } ospf3NewCfgExtRangeDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ospf3NewCfgExtRangeEntry 8 } -- ospfv3 redist entries ospf3CurCfgRedistTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3CurCfgRedistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 redistribution entries in the current configuration." ::= { ospf3Cfg 16 } ospf3CurCfgRedistEntry OBJECT-TYPE SYNTAX Ospf3CurCfgRedistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPFv3 redistribution entry." INDEX { ospf3CurCfgRedistIndex } ::= { ospf3CurCfgRedistTable 1 } Ospf3CurCfgRedistEntry ::= SEQUENCE { ospf3CurCfgRedistIndex Integer32, ospf3CurCfgRedistAddr DisplayString, ospf3CurCfgRedistPrefixLen INTEGER, ospf3CurCfgRedistMetric INTEGER, ospf3CurCfgRedistMetricType INTEGER, ospf3CurCfgRedistRouteTagTypeManual INTEGER, ospf3CurCfgRedistRouteTag Unsigned32, ospf3CurCfgRedistState INTEGER } ospf3CurCfgRedistIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The redistribution entry number for which the OSPFv3 redistribution entry table is related." ::= { ospf3CurCfgRedistEntry 1} ospf3CurCfgRedistAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 Address of the redistribution entry." ::= { ospf3CurCfgRedistEntry 2 } ospf3CurCfgRedistPrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The prefix length of the redistribution entry." ::= { ospf3CurCfgRedistEntry 3 } ospf3CurCfgRedistMetric OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-only STATUS current DESCRIPTION "The metric to be applied to the route." ::= { ospf3CurCfgRedistEntry 4 } ospf3CurCfgRedistMetricType OBJECT-TYPE SYNTAX INTEGER { asExttype1(3), asExttype2(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The metric type. asExttype1(3), asExttype2(4)" ::= { ospf3CurCfgRedistEntry 5 } ospf3CurCfgRedistRouteTag OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The route tag of the redistribution entry." ::= { ospf3CurCfgRedistEntry 6 } ospf3CurCfgRedistRouteTagTypeManual OBJECT-TYPE SYNTAX INTEGER { auto(0), manual(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if the route tag is set manually. " ::= { ospf3CurCfgRedistEntry 7 } ospf3CurCfgRedistState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the redistribution entry." ::= { ospf3CurCfgRedistEntry 8 } ospf3NewCfgRedistTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3NewCfgRedistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 summary redistribution entry in the new configuration." ::= { ospf3Cfg 17 } ospf3NewCfgRedistEntry OBJECT-TYPE SYNTAX Ospf3NewCfgRedistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPFv3 summary redistribution entry." INDEX { ospf3NewCfgRedistIndex } ::= { ospf3NewCfgRedistTable 1 } Ospf3NewCfgRedistEntry ::= SEQUENCE { ospf3NewCfgRedistIndex Integer32, ospf3NewCfgRedistAddr DisplayString, ospf3NewCfgRedistPrefixLen INTEGER, ospf3NewCfgRedistMetric INTEGER, ospf3NewCfgRedistMetricType INTEGER, ospf3NewCfgRedistRouteTagTypeManual INTEGER, ospf3NewCfgRedistRouteTag Unsigned32, ospf3NewCfgRedistState INTEGER, ospf3NewCfgRedistDelete INTEGER } ospf3NewCfgRedistIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The redistribution entry number for which the OSPFv3 redistribution entry table is related." ::= { ospf3NewCfgRedistEntry 1} ospf3NewCfgRedistAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "The IPv6 Address of the redistribution entry. Address should be 4-byte haxadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx or ::xxxx" ::= { ospf3NewCfgRedistEntry 2 } ospf3NewCfgRedistPrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The prefix length of the redistribution entry." ::= { ospf3NewCfgRedistEntry 3 } ospf3NewCfgRedistMetric OBJECT-TYPE SYNTAX INTEGER (1..16777215) MAX-ACCESS read-create STATUS current DESCRIPTION "The metric to be applied to the route." ::= { ospf3NewCfgRedistEntry 4 } ospf3NewCfgRedistMetricType OBJECT-TYPE SYNTAX INTEGER { asExttype1(3), asExttype2(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The metric type. asExttype1(3), asExttype2(4)" ::= { ospf3NewCfgRedistEntry 5 } ospf3NewCfgRedistRouteTag OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The route tag of the redistribution entry." ::= { ospf3NewCfgRedistEntry 6 } ospf3NewCfgRedistRouteTagTypeManual OBJECT-TYPE SYNTAX INTEGER { auto(0), manual(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates if the route tag is set manually. " ::= { ospf3NewCfgRedistEntry 7 } ospf3NewCfgRedistState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the redistribution entry." ::= { ospf3NewCfgRedistEntry 8 } ospf3NewCfgRedistDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ospf3NewCfgRedistEntry 9 } ospf3RouteRedistribution OBJECT IDENTIFIER ::= { ospf3Cfg 18 } ospf3RedistributeConnected OBJECT IDENTIFIER ::= { ospf3RouteRedistribution 1 } ospf3CurCfgConnectedMetric OBJECT-TYPE SYNTAX INTEGER (0..16777215) MAX-ACCESS read-only STATUS current DESCRIPTION "The metric to be assigned to Connected routes." ::= { ospf3RedistributeConnected 1 } ospf3NewCfgConnectedMetric OBJECT-TYPE SYNTAX INTEGER (0..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The metric to be assigned to Connected routes." ::= { ospf3RedistributeConnected 2 } ospf3CurCfgConnectedMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The AS External metric type for Connected routes." ::= { ospf3RedistributeConnected 3 } ospf3NewCfgConnectedMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The AS External metric type for Connected routes." ::= { ospf3RedistributeConnected 4 } ospf3CurCfgConnectedRouteTag OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "Assigned route tag " ::= { ospf3RedistributeConnected 5 } ospf3NewCfgConnectedRouteTag OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "Assigned route tag " ::= { ospf3RedistributeConnected 6 } ospf3CurCfgConnectedRouteTagTypeManual OBJECT-TYPE SYNTAX INTEGER { auto(0), manual(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if the route tag is set manually." ::= { ospf3RedistributeConnected 7 } ospf3NewCfgConnectedRouteTagTypeManual OBJECT-TYPE SYNTAX INTEGER { auto(0), manual(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates if the route tag is set manually." ::= { ospf3RedistributeConnected 8 } ospf3RedistributeStatic OBJECT IDENTIFIER ::= { ospf3RouteRedistribution 2 } ospf3CurCfgStaticMetric OBJECT-TYPE SYNTAX INTEGER (0..16777215) MAX-ACCESS read-only STATUS current DESCRIPTION "The metric to be assigned to static routes." ::= { ospf3RedistributeStatic 1 } ospf3NewCfgStaticMetric OBJECT-TYPE SYNTAX INTEGER (0..16777215) MAX-ACCESS read-write STATUS current DESCRIPTION "The metric to be assigned to static routes." ::= { ospf3RedistributeStatic 2 } ospf3CurCfgStaticMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The AS External metric type for static routes." ::= { ospf3RedistributeStatic 3 } ospf3NewCfgStaticMetricType OBJECT-TYPE SYNTAX INTEGER { none(1), type1(2), type2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The AS External metric type for static routes." ::= { ospf3RedistributeStatic 4 } ospf3CurCfgStaticRouteTag OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "Assigned route tag " ::= { ospf3RedistributeStatic 5 } ospf3NewCfgStaticRouteTag OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "Assigned route tag " ::= { ospf3RedistributeStatic 6 } ospf3CurCfgStaticRouteTagTypeManual OBJECT-TYPE SYNTAX INTEGER { auto(0), manual(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if the route tag is set manually." ::= { ospf3RedistributeStatic 7 } ospf3NewCfgStaticRouteTagTypeManual OBJECT-TYPE SYNTAX INTEGER { auto(0), manual(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates if the route tag is set manually." ::= { ospf3RedistributeStatic 8 } ipv6PmtuCurTimeout OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "IPv6 PMTU Expired Time Value(0|10-100), 0 indicates INFINITY. Other values should be in [10, 100]" ::= { ipv6pmtuCfg 1 } ipv6PmtuNewTimeout OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "IPv6 PMTU Expired Time Value(0|10-100), 0 indicates INFINITY. Other values should be in [10, 100]" ::= { ipv6pmtuCfg 2 } ipv6PmtuEntriesClearAll OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to clear(2),clears all ipv6 PMTU entries. Otherwhise nothing is done." ::= { ipv6pmtuCfg 3} ipCurCfgRouterID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The router ID of the switch." ::= { ipGeneralCfg 1 } ipNewCfgRouterID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The router ID of the switch." ::= { ipGeneralCfg 2 } vlanFloodCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanFloodCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VLAN flooding configuration." ::= { floodingCfg 1 } vlanFloodCurCfgTableEntry OBJECT-TYPE SYNTAX VlanFloodCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the VLAN flooding configuration table." INDEX { vlanFloodCurCfgVlanId } ::= { vlanFloodCurCfgTable 1 } VlanFloodCurCfgTableEntry ::= SEQUENCE { vlanFloodCurCfgVlanId Integer32, vlanFloodCurCfgFlood INTEGER ,vlanFloodCurCfgCpu INTEGER ,vlanFloodCurCfgOptFlood INTEGER } vlanFloodCurCfgVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN identifier." ::= { vlanFloodCurCfgTableEntry 1 } vlanFloodCurCfgFlood OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable flooding unregistered IPMCs" ::= { vlanFloodCurCfgTableEntry 2 } vlanFloodCurCfgCpu OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable sending unregistered IPMCs to CPU" ::= { vlanFloodCurCfgTableEntry 3 } vlanFloodCurCfgOptFlood OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable optimized flooding" ::= { vlanFloodCurCfgTableEntry 4 } vlanFloodNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanFloodNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VLAN flooding configuration." ::= { floodingCfg 2 } vlanFloodNewCfgTableEntry OBJECT-TYPE SYNTAX VlanFloodNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the VLAN flooding configuration table." INDEX { vlanFloodNewCfgVlanId } ::= { vlanFloodNewCfgTable 1 } VlanFloodNewCfgTableEntry ::= SEQUENCE { vlanFloodNewCfgVlanId Integer32, vlanFloodNewCfgFlood INTEGER ,vlanFloodNewCfgCpu INTEGER ,vlanFloodNewCfgOptFlood INTEGER } vlanFloodNewCfgVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN identifier." ::= { vlanFloodNewCfgTableEntry 1 } vlanFloodNewCfgFlood OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable flooding unregistered IPMCs" ::= { vlanFloodNewCfgTableEntry 2 } vlanFloodNewCfgCpu OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable sending unregistered IPMCs to CPU" ::= { vlanFloodNewCfgTableEntry 3 } vlanFloodNewCfgOptFlood OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable optimized flooding" ::= { vlanFloodNewCfgTableEntry 4 } -- IGMP config igmpCurCfgOnOff OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Globally turn IGMP On/Off." ::= { igmpCfg 1} igmpNewCfgOnOff OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Globally turn IGMP On/Off." ::= { igmpCfg 2} igmpSnoopCfg OBJECT IDENTIFIER ::= { igmpCfg 9 } -- IGMP Snooping config igmpSnoopCurCfgMrto OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of multicast router timeout in the current config." ::= { igmpSnoopCfg 7 } igmpSnoopNewCfgMrto OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The value of multicast router timeout in the new config." ::= { igmpSnoopCfg 8 } igmpSnoopCurCfgAggrEnaDis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/Disable of IGMP Report aggregation." ::= { igmpSnoopCfg 9} igmpSnoopNewCfgAggrEnaDis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable of IGMP Report aggregation." ::= { igmpSnoopCfg 10} igmpSnoopCurCfgEnaDis OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of IGMP Snooping." ::= { igmpSnoopCfg 11} igmpSnoopNewCfgEnaDis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set Enable/Disable of IGMP Snooping." ::= { igmpSnoopCfg 12} igmpSnoopNewCfgVlanAdd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN to be added to snooping vlan list. When read, 0 is returned." ::= { igmpSnoopCfg 13 } igmpSnoopNewCfgVlanRem OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN to be removed from snooping vlan list. When read, 0 is returned." ::= { igmpSnoopCfg 14 } igmpSnoopNewCfgVlanClear OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Removing ALL Snooping Vlans." ::= { igmpSnoopCfg 15 } igmpSnoopCurCfgVlanBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The snooping vlans present in the vlan map list. The snooping vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Vlan 9 || || || ||___ Vlan 8 || |____ Vlan 7 || . . . ||_________ Vlan 2 |__________ Vlan 1 where x : 1 - The represented vlan has snoop enabled 0 - The represented vlan does not have snooping enabled." ::= { igmpSnoopCfg 16 } igmpSnoopNewCfgVlanBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The snooping vlans present in the vlan map list. The snooping vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Vlan 9 || || || ||___ Vlan 8 || |____ Vlan 7 || . . . ||_________ Vlan 2 |__________ Vlan 1 where x : 1 - The represented vlan has snoop enabled 0 - The represented vlan does not have snooping enabled." ::= { igmpSnoopCfg 17 } igmpSnoopCurCfgSrcIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source ip for GSQ proxy in current config." ::= { igmpSnoopCfg 26 } igmpSnoopNewCfgSrcIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The source ip for GSQ proxy in new config." ::= { igmpSnoopCfg 27 } igmpSnoopSetToDefault OBJECT-TYPE SYNTAX INTEGER { none(1), setDefault(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When setting the value setDefault(2), the IGMP Snooping configuration is set to the default values. When reading, none(1) is always returned." ::= { igmpSnoopCfg 33} igmpStaticMrtrCfg OBJECT IDENTIFIER ::= { igmpCfg 10 } igmpFilterCfg OBJECT IDENTIFIER ::= { igmpCfg 11 } igmpRelayCfg OBJECT IDENTIFIER ::= { igmpCfg 12 } igmpAdvCfg OBJECT IDENTIFIER ::= { igmpCfg 13 } igmpV3SnoopCfg OBJECT IDENTIFIER ::= { igmpCfg 14 } igmpV3SnoopCurCfgSources OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of sources to snoop in a group record in current config." ::= { igmpV3SnoopCfg 1 } igmpV3SnoopNewCfgSources OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Number of sources to snoop in a group record in new config." ::= { igmpV3SnoopCfg 2 } igmpV3SnoopCurCfgEnaDis OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of IGMP V3 Snooping." ::= { igmpV3SnoopCfg 3 } igmpV3SnoopNewCfgEnaDis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set Enable/Disable of IGMP V3 Snooping." ::= { igmpV3SnoopCfg 4 } igmpV3SnoopCurCfgExcludeEnaDis OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of IGMP V3 EXCLUDE filter-mode Snooping." ::= { igmpV3SnoopCfg 5 } igmpV3SnoopNewCfgExcludeEnaDis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set Enable/Disable of IGMP V3 EXCLUDE filter-mode Snooping." ::= { igmpV3SnoopCfg 6 } igmpV3SnoopCurCfgV1V2EnaDis OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of IGMP V1/V2 Report Snooping." ::= { igmpV3SnoopCfg 7 } igmpV3SnoopNewCfgV1V2EnaDis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set Enable/Disable of IGMP V1/V2 Report Snooping." ::= { igmpV3SnoopCfg 8 } -- IGMP Static Mrtr Support igmpStaticMrtrCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpStaticMrtrCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IGMP Static Multicast Router table in the current configuration block." ::= { igmpStaticMrtrCfg 1 } igmpStaticMrtrCurCfgTableEntry OBJECT-TYPE SYNTAX IgmpStaticMrtrCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Static Multicast Router table." INDEX { igmpStaticMrtrCurCfgIndx } ::= { igmpStaticMrtrCurCfgTable 1 } IgmpStaticMrtrCurCfgTableEntry ::= SEQUENCE { igmpStaticMrtrCurCfgIndx INTEGER, igmpStaticMrtrCurCfgPortId PortNumber, igmpStaticMrtrCurCfgVlanId INTEGER, igmpStaticMrtrCurCfgVersion INTEGER } igmpStaticMrtrCurCfgIndx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP Multicast Router table port index." ::= { igmpStaticMrtrCurCfgTableEntry 1 } igmpStaticMrtrCurCfgPortId OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP Multicast Router port in the current configuration block." ::= { igmpStaticMrtrCurCfgTableEntry 2 } igmpStaticMrtrCurCfgVlanId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP Multicast Router port in the current configuration block." ::= { igmpStaticMrtrCurCfgTableEntry 3 } igmpStaticMrtrCurCfgVersion OBJECT-TYPE SYNTAX INTEGER { version1(1), version2(2), version3(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP version of the IGMP Static Multicast Router." ::= { igmpStaticMrtrCurCfgTableEntry 4 } igmpStaticMrtrNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpStaticMrtrNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IGMP Static Multicast Router table in the new configuration block." ::= { igmpStaticMrtrCfg 2 } igmpStaticMrtrNewCfgTableEntry OBJECT-TYPE SYNTAX IgmpStaticMrtrNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Static Multicast Router table." INDEX { igmpStaticMrtrNewCfgIndx } ::= { igmpStaticMrtrNewCfgTable 1 } IgmpStaticMrtrNewCfgTableEntry ::= SEQUENCE { igmpStaticMrtrNewCfgIndx INTEGER, igmpStaticMrtrNewCfgPortId PortNumber, igmpStaticMrtrNewCfgVlanId INTEGER, igmpStaticMrtrNewCfgVersion INTEGER, igmpStaticMrtrNewCfgDelete INTEGER } igmpStaticMrtrNewCfgIndx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP Multicast Router table port index." ::= { igmpStaticMrtrNewCfgTableEntry 1 } igmpStaticMrtrNewCfgPortId OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The IGMP Multicast Router port in the new configuration block." ::= { igmpStaticMrtrNewCfgTableEntry 2 } igmpStaticMrtrNewCfgVlanId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The IGMP Multicast Router port in the new configuration block." ::= { igmpStaticMrtrNewCfgTableEntry 3 } igmpStaticMrtrNewCfgVersion OBJECT-TYPE SYNTAX INTEGER { version1(1), version2(2), version3(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The IGMP version of the IGMP Static Multicast Router." ::= { igmpStaticMrtrNewCfgTableEntry 4 } igmpStaticMrtrNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { igmpStaticMrtrNewCfgTableEntry 5 } igmpStaticMrtrNewCfgClear OBJECT-TYPE SYNTAX INTEGER { other(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to the value of 2 (clear), the entire table is deleted. When read, other(1) is returned. Setting the value to anything other than 2(clear) has no effect on the table." ::= { igmpStaticMrtrCfg 3 } -- IGMP Filtering igmpFltCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpFltCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IGMP filtering table in the current configuration block." ::= { igmpFilterCfg 1 } igmpFltCurCfgTableEntry OBJECT-TYPE SYNTAX IgmpFltCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the filtering table." INDEX { igmpFltCurCfgIndx } ::= { igmpFltCurCfgTable 1 } IgmpFltCurCfgTableEntry ::= SEQUENCE { igmpFltCurCfgIndx INTEGER, igmpFltCurCfgMcastIp1 IpAddress, igmpFltCurCfgMcastIp2 IpAddress, igmpFltCurCfgAction INTEGER, igmpFltCurCfgState INTEGER } igmpFltCurCfgIndx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP filter table index." ::= { igmpFltCurCfgTableEntry 1 } igmpFltCurCfgMcastIp1 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Range1 Multicast IP address to be filtered." ::= { igmpFltCurCfgTableEntry 2 } igmpFltCurCfgMcastIp2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Range2 Multicast IP address to be filtered." ::= { igmpFltCurCfgTableEntry 3 } igmpFltCurCfgAction OBJECT-TYPE SYNTAX INTEGER { allow(1), deny(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The action for the IGMP filtering rule." ::= { igmpFltCurCfgTableEntry 4 } igmpFltCurCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of this IGMP filtering rule." ::= { igmpFltCurCfgTableEntry 5 } igmpFltNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpFltNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IGMP filtering table in the current configuration block." ::= { igmpFilterCfg 2 } igmpFltNewCfgTableEntry OBJECT-TYPE SYNTAX IgmpFltNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the filtering table." INDEX { igmpFltNewCfgIndx } ::= { igmpFltNewCfgTable 1 } IgmpFltNewCfgTableEntry ::= SEQUENCE { igmpFltNewCfgIndx INTEGER, igmpFltNewCfgMcastIp1 IpAddress, igmpFltNewCfgMcastIp2 IpAddress, igmpFltNewCfgAction INTEGER, igmpFltNewCfgState INTEGER, igmpFltNewCfgDelete INTEGER } igmpFltNewCfgIndx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP filter table index." ::= { igmpFltNewCfgTableEntry 1 } igmpFltNewCfgMcastIp1 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Range1 Multicast source IP address to be filtered." ::= { igmpFltNewCfgTableEntry 2 } igmpFltNewCfgMcastIp2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Range2 Multicast source IP address to be filtered." ::= { igmpFltNewCfgTableEntry 3 } igmpFltNewCfgAction OBJECT-TYPE SYNTAX INTEGER { allow(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The action for the IGMP filtering rule." ::= { igmpFltNewCfgTableEntry 4 } igmpFltNewCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The state of this IGMP filtering rule." ::= { igmpFltNewCfgTableEntry 5 } igmpFltNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other(1) is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { igmpFltNewCfgTableEntry 6 } -- IGMP Filtering Port Table igmpFltCurCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpFltCurCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IGMP filtering port table in the current configuration block." ::= { igmpFilterCfg 3 } igmpFltCurCfgPortTableEntry OBJECT-TYPE SYNTAX IgmpFltCurCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the IGMP filtering port table." INDEX { igmpFltCurCfgPortIndx } ::= { igmpFltCurCfgPortTable 1 } IgmpFltCurCfgPortTableEntry ::= SEQUENCE { igmpFltCurCfgPortIndx PortNumber, igmpFltCurCfgPortState INTEGER, igmpFltCurCfgPortFiltBmap OCTET STRING } igmpFltCurCfgPortIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port index." ::= { igmpFltCurCfgPortTableEntry 1 } igmpFltCurCfgPortState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable or disable IGMP filtering." ::= { igmpFltCurCfgPortTableEntry 2 } igmpFltCurCfgPortFiltBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP filtering rules applied to the port. The filtering rules are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ filter 9 || || || ||___ filter 8 || |____ filter 7 || . . . ||_________ filter 2 |__________ filter 1 (as index to igmpFltCurCfgTable) where x : 1 - The represented IGMP filter rule applied to the port 0 - The represented IGMP filter rule not applied to the port " ::= { igmpFltCurCfgPortTableEntry 3 } igmpFltNewCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpFltNewCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IGMP filtering port table in the new configuration block." ::= { igmpFilterCfg 4 } igmpFltNewCfgPortTableEntry OBJECT-TYPE SYNTAX IgmpFltNewCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the IGMP filtering port table." INDEX { igmpFltNewCfgPortIndx } ::= { igmpFltNewCfgPortTable 1 } IgmpFltNewCfgPortTableEntry ::= SEQUENCE { igmpFltNewCfgPortIndx PortNumber, igmpFltNewCfgPortState INTEGER, igmpFltNewCfgPortFiltBmap OCTET STRING, igmpFltNewCfgPortAddFiltRule INTEGER, igmpFltNewCfgPortRemFiltRule INTEGER } igmpFltNewCfgPortIndx OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port index." ::= { igmpFltNewCfgPortTableEntry 1 } igmpFltNewCfgPortState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable IGMP filtering." ::= { igmpFltNewCfgPortTableEntry 2 } igmpFltNewCfgPortFiltBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP filtering rules applied to the port. The filtering rules are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ filter 9 || || || ||___ filter 8 || |____ filter 7 || . . . ||_________ filter 2 |__________ filter 1 (as index to fltNewCfgTable) where x : 1 - The represented filter rule applied to the port 0 - The represented filter rule not applied to the port " ::= { igmpFltNewCfgPortTableEntry 3 } igmpFltNewCfgPortAddFiltRule OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to add filtering rule to a port. The value specified with this object is the index to the fltNewCfgTable for which filtering rule to be added to the port. The range of the valid index is between 1 and igmpFltCurCfgTableMaxSize. When read, the value '0' is returned always." ::= { igmpFltNewCfgPortTableEntry 4 } igmpFltNewCfgPortRemFiltRule OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to remove filtering rule from a port. The value specified with this object is the index to the fltNewCfgTable for which filtering rule to be removed from the port. The range of the valid index is between 1 and igmpFltCurCfgTableMaxSize. When read, the value '0' is returned always." ::= { igmpFltNewCfgPortTableEntry 5 } igmpFltCurCfgEnaDis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/Disable of IGMP Filtering." ::= { igmpFilterCfg 5 } igmpFltNewCfgEnaDis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable of IGMP Filtering." ::= { igmpFilterCfg 6 } -- -- IGMP Relay Configuration -- igmpRelayCurCfgEnaDis OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of IGMP Relay." ::= { igmpRelayCfg 1 } igmpRelayNewCfgEnaDis OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable of IGMP Relay." ::= { igmpRelayCfg 2 } igmpRelayNewCfgAddVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN to be added to relay vlan list. When read, 0 is returned." ::= { igmpRelayCfg 3 } igmpRelayNewCfgRemVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN to be removed from relay vlan list. When read, 0 is returned." ::= { igmpRelayCfg 4 } igmpRelayNewCfgClearVlan OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Removing ALL Relay Vlans." ::= { igmpRelayCfg 5 } igmpRelayCurCfgVlanBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The relay vlans present in the vlan map list. The relay vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Vlan 9 || || || ||___ Vlan 8 || |____ Vlan 7 || . . . ||_________ Vlan 2 |__________ Vlan 1 where x : 1 - The represented vlan has relay enabled 0 - The represented vlan does not have relay enabled." ::= { igmpRelayCfg 6 } igmpRelayNewCfgVlanBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The relay vlans present in the vlan map list. The relay vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Vlan 9 || || || ||___ Vlan 8 || |____ Vlan 7 || . . . ||_________ Vlan 2 |__________ Vlan 1 where x : 1 - The represented vlan has relay enabled 0 - The represented vlan does not have relay enabled." ::= { igmpRelayCfg 7 } igmpRelayCurCfgReport OBJECT-TYPE SYNTAX INTEGER(0..150) MAX-ACCESS read-only STATUS current DESCRIPTION "The Unsolicited Report Interval." ::= { igmpRelayCfg 8 } igmpRelayNewCfgReport OBJECT-TYPE SYNTAX INTEGER(0..150) MAX-ACCESS read-write STATUS current DESCRIPTION "Set Unsolicited Report Interval." ::= { igmpRelayCfg 9 } igmpRelayMrtrCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpRelayMrtrCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IGMP relay multicast router table in the current configuration block." ::= { igmpRelayCfg 10 } igmpRelayMrtrCurCfgTableEntry OBJECT-TYPE SYNTAX IgmpRelayMrtrCurCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the IGMP relay multicast router table." INDEX { igmpRelayMrtrCurCfgIndx } ::= { igmpRelayMrtrCurCfgTable 1 } IgmpRelayMrtrCurCfgTableEntry ::= SEQUENCE { igmpRelayMrtrCurCfgIndx INTEGER, igmpRelayMrtrCurCfgAddr IpAddress, igmpRelayMrtrCurCfgEnaDis INTEGER, igmpRelayMrtrCurCfgInterval INTEGER, igmpRelayMrtrCurCfgRetry INTEGER, igmpRelayMrtrCurCfgRestr INTEGER, igmpRelayMrtrCurCfgVersion INTEGER } igmpRelayMrtrCurCfgIndx OBJECT-TYPE SYNTAX INTEGER(1..2) MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP relay multicast router table index." ::= { igmpRelayMrtrCurCfgTableEntry 1 } igmpRelayMrtrCurCfgAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the multicast router." ::= { igmpRelayMrtrCurCfgTableEntry 2 } igmpRelayMrtrCurCfgEnaDis OBJECT-TYPE SYNTAX INTEGER{ enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the multicast router." ::= { igmpRelayMrtrCurCfgTableEntry 3 } igmpRelayMrtrCurCfgInterval OBJECT-TYPE SYNTAX INTEGER(1..60) MAX-ACCESS read-only STATUS current DESCRIPTION "The interval between ping attempts." ::= { igmpRelayMrtrCurCfgTableEntry 4 } igmpRelayMrtrCurCfgRetry OBJECT-TYPE SYNTAX INTEGER(1..120) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of failed attempts to declare router DOWN." ::= { igmpRelayMrtrCurCfgTableEntry 5 } igmpRelayMrtrCurCfgRestr OBJECT-TYPE SYNTAX INTEGER(1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of successful attempts to declare router UP." ::= { igmpRelayMrtrCurCfgTableEntry 6 } igmpRelayMrtrCurCfgVersion OBJECT-TYPE SYNTAX INTEGER{ igmpv1(1), igmpv2(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP version." ::= { igmpRelayMrtrCurCfgTableEntry 7 } igmpRelayMrtrNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpRelayMrtrNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IGMP relay multicast router table in the new configuration block." ::= { igmpRelayCfg 11 } igmpRelayMrtrNewCfgTableEntry OBJECT-TYPE SYNTAX IgmpRelayMrtrNewCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the IGMP relay multicast router table." INDEX { igmpRelayMrtrNewCfgIndx } ::= { igmpRelayMrtrNewCfgTable 1 } IgmpRelayMrtrNewCfgTableEntry ::= SEQUENCE { igmpRelayMrtrNewCfgIndx INTEGER, igmpRelayMrtrNewCfgAddr IpAddress, igmpRelayMrtrNewCfgEnaDis INTEGER, igmpRelayMrtrNewCfgInterval INTEGER, igmpRelayMrtrNewCfgRetry INTEGER, igmpRelayMrtrNewCfgRestr INTEGER, igmpRelayMrtrNewCfgVersion INTEGER, igmpRelayMrtrNewCfgRemove INTEGER } igmpRelayMrtrNewCfgIndx OBJECT-TYPE SYNTAX INTEGER(1..2) MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP relay multicast router table index." ::= { igmpRelayMrtrNewCfgTableEntry 1 } igmpRelayMrtrNewCfgAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the multicast router." ::= { igmpRelayMrtrNewCfgTableEntry 2 } igmpRelayMrtrNewCfgEnaDis OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The status of the multicast router." ::= { igmpRelayMrtrNewCfgTableEntry 3 } igmpRelayMrtrNewCfgInterval OBJECT-TYPE SYNTAX INTEGER(1..60) MAX-ACCESS read-write STATUS current DESCRIPTION "The interval between ping attempts." ::= { igmpRelayMrtrNewCfgTableEntry 4 } igmpRelayMrtrNewCfgRetry OBJECT-TYPE SYNTAX INTEGER(1..120) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of failed attempts to declare router DOWN." ::= { igmpRelayMrtrNewCfgTableEntry 5 } igmpRelayMrtrNewCfgRestr OBJECT-TYPE SYNTAX INTEGER(1..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of successful attempts to declare router UP." ::= { igmpRelayMrtrNewCfgTableEntry 6 } igmpRelayMrtrNewCfgVersion OBJECT-TYPE SYNTAX INTEGER{ igmpv1(1), igmpv2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The IGMP version." ::= { igmpRelayMrtrNewCfgTableEntry 7 } igmpRelayMrtrNewCfgRemove OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete the IGMP Relay multicast router." ::= { igmpRelayMrtrNewCfgTableEntry 8 } -- -- IGMP Configuration Advanced Menu -- igmpAdvCurCfgQInterval OBJECT-TYPE SYNTAX INTEGER(1..600) MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP Query Interval of current config." ::= { igmpAdvCfg 1 } igmpAdvNewCfgQInterval OBJECT-TYPE SYNTAX INTEGER(1..600) MAX-ACCESS read-write STATUS current DESCRIPTION "The IGMP Query Interval of new config." ::= { igmpAdvCfg 2 } igmpAdvCurCfgRobust OBJECT-TYPE SYNTAX INTEGER(1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of expected packet loss on subnet in current config." ::= { igmpAdvCfg 3 } igmpAdvNewCfgRobust OBJECT-TYPE SYNTAX INTEGER(1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Set the value of expected packet loss on subnet." ::= { igmpAdvCfg 4 } igmpAdvCurCfgTimeout OBJECT-TYPE SYNTAX INTEGER(1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP Report timeout." ::= { igmpAdvCfg 5 } igmpAdvNewCfgTimeout OBJECT-TYPE SYNTAX INTEGER(1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Set IGMP Report timeout." ::= { igmpAdvCfg 6 } igmpAdvNewCfgVlanFastlvAdd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN to be added to quick-leave vlan list. When read, 0 is returned." ::= { igmpAdvCfg 7 } igmpAdvNewCfgVlanFastlvRem OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN to be removed from quick-leave vlan list. When read, 0 is returned." ::= { igmpAdvCfg 8 } igmpAdvCurCfgVlanFastlvBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The fast-leave enabled vlans present in the vlan map list. The fast-leave enabled vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Vlan 9 || || || ||___ Vlan 8 || |____ Vlan 7 || . . . ||_________ Vlan 2 |__________ Vlan 1 where x : 1 - The represented vlan has fast-leave enabled 0 - The represented vlan does not have fast-leave enabled." ::= { igmpAdvCfg 9 } igmpAdvNewCfgVlanFastlvBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The fast-leave enabled vlans present in the vlan map list. The fast-leave enabled vlans are presented in a bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Vlan 9 || || || ||___ Vlan 8 || |____ Vlan 7 || . . . ||_________ Vlan 2 |__________ Vlan 1 where x : 1 - The represented vlan has fast-leave enabled 0 - The represented vlan does not have fast-leave enabled." ::= { igmpAdvCfg 10 } igmpAdvCurCfgRtrAlert OBJECT-TYPE SYNTAX INTEGER{ enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable sending IGMP messages with Router Alert option." ::= { igmpAdvCfg 15 } igmpAdvNewCfgRtrAlert OBJECT-TYPE SYNTAX INTEGER{ enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable sending IGMP messages with Router Alert option." ::= { igmpAdvCfg 16 } igmpCurQurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpCurQurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IGMP querier configuration." ::= { igmpCfg 15 } igmpCurQurCfgEntry OBJECT-TYPE SYNTAX IgmpCurQurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the IGMP querier configuration table" INDEX { igmpCurQurCfgVlanIndex } ::= { igmpCurQurCfgTable 1 } IgmpCurQurCfgEntry ::= SEQUENCE { igmpCurQurCfgVlanIndex INTEGER, igmpCurQuerierState INTEGER, igmpCurCfgQuerier INTEGER, igmpCurCfgQueryInterval INTEGER, igmpCurCfgQurSrcIp IpAddress, igmpCurCfgElectionType INTEGER, igmpCurCfgQurRobustness INTEGER, igmpCurCfgQurStartupCnt INTEGER, igmpCurCfgQurStartupInt INTEGER, igmpCurCfgQurMaxRespTime INTEGER, igmpCurCfgOtherQurAddress DisplayString, igmpCurCfgOtherQurPresentInt DisplayString, igmpCurCfgVlanOperVersion INTEGER, igmpCurVlanOperVersion INTEGER, igmpCurVlanOlderVerTimer DisplayString } igmpCurQurCfgVlanIndex OBJECT-TYPE SYNTAX INTEGER(1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan number for which the IGMP querier information is related." ::= { igmpCurQurCfgEntry 1} igmpCurQuerierState OBJECT-TYPE SYNTAX INTEGER { querier(1), nonQuerier(2), checkingMembership(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the switch is running as a querier in the VLAN. Based on the querier election, if elected as a querier, it will send query messages. If the switch receives the query message with lower IP/MAC any other querier in the VLAN, It will move to non querier state. If a leave is received then querier moves to checking membership state." ::= { igmpCurQurCfgEntry 2} igmpCurCfgQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The snooping switch can be configured to send IGMP queries. querier are not present in the VLAN and it set to 'enabled' the switch will generate general query messages. The query messages will be suppressed if the switch receives the query message from any other querier with lower IP/MAC in the VLAN." ::= { igmpCurQurCfgEntry 3} igmpCurCfgQueryInterval OBJECT-TYPE SYNTAX INTEGER(1..608) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN." ::= { igmpCurQurCfgEntry 4 } igmpCurCfgQurSrcIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source ip for GSQ proxy in this vlan. This Src Ip will be used in querier election mechanism. It will be the source address in queries sent bye the switch." ::= { igmpCurQurCfgEntry 5 } igmpCurCfgElectionType OBJECT-TYPE SYNTAX INTEGER { ipv4(1), macaddr(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The querier selection type specify the criteria to be used to elect querier for this VLAN. When a switch is configured as a querier, this will define the election criteria . e.g. MAC or source IP-address." ::= { igmpCurQurCfgEntry 6 } igmpCurCfgQurRobustness OBJECT-TYPE SYNTAX INTEGER(1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The Robustness Variable allows tuning for the Other Querier Present Interval." ::= { igmpCurQurCfgEntry 7 } igmpCurCfgQurStartupCnt OBJECT-TYPE SYNTAX INTEGER(1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "Represents the number of Queries sent out on startup of querier election, separated by the Startup Query Interval." ::= { igmpCurQurCfgEntry 8 } igmpCurCfgQurStartupInt OBJECT-TYPE SYNTAX INTEGER(1..608) MAX-ACCESS read-only STATUS current DESCRIPTION "This variable represents the interval(in seconds) between General Queries sent by a Querier on startup. By default: 1/4 the Query Interval." ::= { igmpCurQurCfgEntry 9 } igmpCurCfgQurMaxRespTime OBJECT-TYPE SYNTAX INTEGER(1..256) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum query response interval advertised in IGMP queries on this VLAN." ::= { igmpCurQurCfgEntry 10 } igmpCurCfgOtherQurAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP/MAC Address of the Querier, which has won the Querier election, when bosSnoopVlanCfgQuerier is enabled on this vlan." ::= { igmpCurQurCfgEntry 11 } igmpCurCfgOtherQurPresentInt OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Other Querier Present Interval is the length of time that must pass before switch decides that there is no longer another multicast router which should be the querier. This value is ((the Robustness Variable) times (the Query Interval)) plus (one half of one Query Response Interval)." ::= { igmpCurQurCfgEntry 12 } igmpCurCfgVlanOperVersion OBJECT-TYPE SYNTAX INTEGER { igmpV1(1), igmpV2(2), igmpV3(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the operating version of the IGMP snooping switch for a specific VLAN. The default operating mode on a specific VLAN is IGMP version 3 i.e, V3(3). The 'bosIgsVlanCfgOperVersion' should be configured on the basis of the version of the router present in the VLAN." ::= { igmpCurQurCfgEntry 13 } igmpCurVlanOperVersion OBJECT-TYPE SYNTAX INTEGER { igmpV1(1), igmpV2(2), igmpV3(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the operating version of the IGMP snooping switch for specific VLAN. The default operating mode on a specific VLAN IGMP version 3 i.e, V3(3)." ::= { igmpCurQurCfgEntry 14 } igmpCurVlanOlderVerTimer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the remaining time of lowest operating version of the vlan. For interoperability with multicast routers/switches/Hosts, running older versions of IGMP, systems maintain a IGMP Version variable for each Vlan. In order to switch gracefully between versions of IGMP, hosts keep both an IGMPv1 Querier Present timer and an IGMPv2 Querier Present timer per Vlan. According to RFC 3376 this value is ((the Robustness Variable) times (the Query Interval)) plus (one Query Response Interval)." ::= { igmpCurQurCfgEntry 15 } igmpNewQurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpNewQurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IGMP querier configuration." ::= { igmpCfg 16 } igmpNewQurCfgEntry OBJECT-TYPE SYNTAX IgmpNewQurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the IGMP querier configuration table" INDEX { igmpNewQurCfgVlanIndex } ::= { igmpNewQurCfgTable 1 } IgmpNewQurCfgEntry ::= SEQUENCE { igmpNewQurCfgVlanIndex INTEGER, igmpNewQuerierState INTEGER, igmpNewCfgQuerier INTEGER, igmpNewCfgQueryInterval INTEGER, igmpNewCfgQurSrcIp IpAddress, igmpNewCfgElectionType INTEGER, igmpNewCfgQurRobustness INTEGER, igmpNewCfgQurStartupCnt INTEGER, igmpNewCfgQurStartupInt INTEGER, igmpNewCfgQurMaxRespTime INTEGER, igmpNewCfgOtherQurAddress DisplayString, igmpNewCfgOtherQurPresentInt DisplayString, igmpNewCfgVlanOperVersion INTEGER, igmpNewVlanOperVersion INTEGER, igmpNewVlanOlderVerTimer DisplayString, igmpNewCfgQuerierDefault INTEGER } igmpNewQurCfgVlanIndex OBJECT-TYPE SYNTAX INTEGER(1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan number for which the IGMP querier information is related." ::= { igmpNewQurCfgEntry 1} igmpNewQuerierState OBJECT-TYPE SYNTAX INTEGER { querier(1), nonQuerier(2), checkingMembership(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the switch is running as a querier in the VLAN. Based on the querier election, if elected as a querier, it will send query messages. If the switch receives the query message with lower IP/MAC any other querier in the VLAN, It will move to non querier state. If a leave is received then querier moves to checking membership state." ::= { igmpNewQurCfgEntry 2} igmpNewCfgQuerier OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The snooping switch can be configured to send IGMP queries. querier are not present in the VLAN and it set to 'enabled' the switch will generate general query messages. The query messages will be suppressed if the switch receives the query message from any other querier with lower IP/MAC in the VLAN." ::= { igmpNewQurCfgEntry 3} igmpNewCfgQueryInterval OBJECT-TYPE SYNTAX INTEGER(1..608) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN." ::= { igmpNewQurCfgEntry 4 } igmpNewCfgQurSrcIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The source ip for GSQ proxy in this vlan. This Src Ip will be used in querier election mechanism. It will be the source address in queries sent bye the switch." ::= { igmpNewQurCfgEntry 5 } igmpNewCfgElectionType OBJECT-TYPE SYNTAX INTEGER { ipv4(1), macaddr(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The querier selection type specify the criteria to be used to elect querier for this VLAN. When a switch is configured as a querier, this will define the election criteria . e.g. MAC or source IP-address." ::= { igmpNewQurCfgEntry 6 } igmpNewCfgQurRobustness OBJECT-TYPE SYNTAX INTEGER(1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The Robustness Variable allows tuning for the Other Querier Present Interval." ::= { igmpNewQurCfgEntry 7 } igmpNewCfgQurStartupCnt OBJECT-TYPE SYNTAX INTEGER(1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "Represents the number of Queries sent out on startup of querier election, separated by the Startup Query Interval." ::= { igmpNewQurCfgEntry 8 } igmpNewCfgQurStartupInt OBJECT-TYPE SYNTAX INTEGER(1..608) MAX-ACCESS read-write STATUS current DESCRIPTION "This variable represents the interval(in seconds) between General Queries sent by a Querier on startup. By default: 1/4 the Query Interval." ::= { igmpNewQurCfgEntry 9 } igmpNewCfgQurMaxRespTime OBJECT-TYPE SYNTAX INTEGER(1..256) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum query response interval advertised in IGMP queries on this VLAN." ::= { igmpNewQurCfgEntry 10 } igmpNewCfgOtherQurAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP/MAC Address of the Querier, which has won the Querier election, when bosSnoopVlanCfgQuerier is enabled on this vlan." ::= { igmpNewQurCfgEntry 11 } igmpNewCfgOtherQurPresentInt OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Other Querier Present Interval is the length of time that must pass before switch decides that there is no longer another multicast router which should be the querier. This value is ((the Robustness Variable) times (the Query Interval)) plus (one half of one Query Response Interval)." ::= { igmpNewQurCfgEntry 12 } igmpNewCfgVlanOperVersion OBJECT-TYPE SYNTAX INTEGER { igmpV1(1), igmpV2(2), igmpV3(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the operating version of the IGMP snooping switch for a specific VLAN. The default operating mode on a specific VLAN is IGMP version 3 i.e, V3(3). The 'igmpNewCfgVlanOperVersion' should be configured on the basis of the version of the mrouter present in the VLAN." ::= { igmpNewQurCfgEntry 13 } igmpNewVlanOperVersion OBJECT-TYPE SYNTAX INTEGER { igmpV1(1), igmpV2(2), igmpV3(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the operating version of the IGMP snooping switch for specific VLAN. The default operating mode on a specific VLAN IGMP version 3 i.e, V3(3)." ::= { igmpNewQurCfgEntry 14 } igmpNewVlanOlderVerTimer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the remaining time of lowest operating version of the vlan. For interoperability with multicast routers/switches/Hosts, running older versions of IGMP, systems maintain a IGMP Version variable for each Vlan. In order to switch gracefully between versions of IGMP, hosts keep both an IGMPv1 Querier Present timer and an IGMPv2 Querier Present timer per Vlan. According to RFC 3376 this value is ((the Robustness Variable) times (the Query Interval)) plus (one Query Response Interval)." ::= { igmpNewQurCfgEntry 15 } igmpNewCfgQuerierDefault OBJECT-TYPE SYNTAX INTEGER { other(1), default(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action to set the default IGMP Querier settings on a Vlan. Returns other(1) when read." ::= { igmpNewQurCfgEntry 16 } igmpCurCfgQuerierOnOff OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of IGMP Querier." ::= { igmpCfg 17} igmpNewCfgQuerierOnOff OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Globally turn IGMP Querier On/Off." ::= { igmpCfg 18} -- -- IPMC Static Route Configuration -- ipmcStaticRouteCfg OBJECT IDENTIFIER ::= { layer3Configs 20 } ipmcStaticRouteTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the IPMC Static Route table." ::= { ipmcStaticRouteCfg 1 } ipmcCurCfgStaticRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF IpmcCurCfgStaticRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of static IPMC routes in the current configuration block." ::= { ipmcStaticRouteCfg 2 } ipmcCurCfgStaticRouteEntry OBJECT-TYPE SYNTAX IpmcCurCfgStaticRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static IPMC route table" INDEX { ipmcCurCfgStaticRouteIndx } ::= { ipmcCurCfgStaticRouteTable 1 } IpmcCurCfgStaticRouteEntry ::= SEQUENCE { ipmcCurCfgStaticRouteIndx Integer32, ipmcCurCfgStaticRouteDestIp IpAddress, ipmcCurCfgStaticRouteVlanId Integer32, ipmcCurCfgStaticRouteHostBmap OCTET STRING, ipmcCurCfgStaticRoutePMrtrBmap OCTET STRING, ipmcCurCfgStaticRouteBMrtrBmap OCTET STRING, ipmcCurCfgStaticRouteVrid Integer32, ipmcCurCfgStaticRouteAdminkeys DisplayString, ipmcCurCfgStaticRouteTrunks OCTET STRING } ipmcCurCfgStaticRouteIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the IPMC static routing table." ::= { ipmcCurCfgStaticRouteEntry 1} ipmcCurCfgStaticRouteDestIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IPMC address of this IPMC route." ::= { ipmcCurCfgStaticRouteEntry 2} ipmcCurCfgStaticRouteVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan id of this route." ::= { ipmcCurCfgStaticRouteEntry 3} ipmcCurCfgStaticRouteHostBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Host ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Port 9 || || || ||___ Port 8 || |____ Port 7 || . . . ||_________ Port 2 |__________ Port 1 where x : 1 - The represented Host Port is added 0 - The represented Host Port is not added" ::= { ipmcCurCfgStaticRouteEntry 4} ipmcCurCfgStaticRoutePMrtrBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Primary Mrouter ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Port 9 || || || ||___ Port 8 || |____ Port 7 || . . . ||_________ Port 2 |__________ Port 1 where x : 1 - The represented Primary Mrouter Port is added 0 - The represented Primary Mrouter Port is not added" ::= { ipmcCurCfgStaticRouteEntry 5} ipmcCurCfgStaticRouteBMrtrBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Backup Mrouter ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Port 9 || || || ||___ Port 8 || |____ Port 7 || . . . ||_________ Port 2 |__________ Port 1 where x : 1 - The represented Backup Mrouter Port is added 0 - The represented Backup Mrouter Port is not added" ::= { ipmcCurCfgStaticRouteEntry 6} ipmcCurCfgStaticRouteVrid OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual router id of this route." ::= { ipmcCurCfgStaticRouteEntry 7} ipmcCurCfgStaticRouteAdminkeys OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The LACP port adminkey of this route. Adminkeys on five positions alligned to right, separated by commas." ::= { ipmcCurCfgStaticRouteEntry 8} ipmcCurCfgStaticRouteTrunks OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The trunk list for this IPMC route. The trunks are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk 8 || || || ||___ trunk 7 || |____ trunk 6 || . . . ||_________ trunk 1 |__________ reserved where x : 1 - The represented trunk belongs to IPMC route 0 - The represented trunk does not belong to IPMC route" ::= { ipmcCurCfgStaticRouteEntry 9 } ipmcNewCfgStaticRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF IpmcNewCfgStaticRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IPMC static routes in the new configuration block. When creating a new route, Destination IP and Vlan id must be set first. The actual change in configuration occurs on using PortInfo leaf." ::= { ipmcStaticRouteCfg 3 } ipmcNewCfgStaticRouteEntry OBJECT-TYPE SYNTAX IpmcNewCfgStaticRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static IPMC route table" INDEX { ipmcNewCfgStaticRouteIndx } ::= { ipmcNewCfgStaticRouteTable 1 } IpmcNewCfgStaticRouteEntry ::= SEQUENCE { ipmcNewCfgStaticRouteIndx Integer32, ipmcNewCfgStaticRouteDestIp IpAddress, ipmcNewCfgStaticRouteVlanId Integer32, ipmcNewCfgStaticRouteHostBmap OCTET STRING, ipmcNewCfgStaticRoutePMrtrBmap OCTET STRING, ipmcNewCfgStaticRouteBMrtrBmap OCTET STRING, ipmcNewCfgStaticRouteAddPort Integer32, ipmcNewCfgStaticRouteRemPort Integer32, ipmcNewCfgStaticRouteTrunks OCTET STRING, ipmcNewCfgStaticRouteAddTrunk INTEGER, ipmcNewCfgStaticRouteRemTrunk INTEGER, ipmcNewCfgStaticRouteAdminkeys DisplayString, ipmcNewCfgStaticRouteAddAdminkey INTEGER, ipmcNewCfgStaticRouteRemAdminkey INTEGER, ipmcNewCfgStaticRoutePortInfo INTEGER, ipmcNewCfgStaticRouteVrid Integer32, ipmcNewCfgStaticRouteDelete INTEGER } ipmcNewCfgStaticRouteIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the IPMC static routing table." ::= { ipmcNewCfgStaticRouteEntry 1} ipmcNewCfgStaticRouteDestIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The destination IPMC address of this route. It must be set along Vlan id before creating new route." ::= { ipmcNewCfgStaticRouteEntry 2} ipmcNewCfgStaticRouteVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The vlan id of this route. It must be set along Destination IP before creating new route." ::= { ipmcNewCfgStaticRouteEntry 3} ipmcNewCfgStaticRouteHostBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Host ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Port 9 || || || ||___ Port 8 || |____ Port 7 || . . . ||_________ Port 2 |__________ Port 1 where x : 1 - The represented Host Port is added 0 - The represented Host Port is not added" ::= { ipmcNewCfgStaticRouteEntry 4} ipmcNewCfgStaticRoutePMrtrBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Primary Mrouter ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Port 9 || || || ||___ Port 8 || |____ Port 7 || . . . ||_________ Port 2 |__________ Port 1 where x : 1 - The represented Primary Mrouter Port is added 0 - The represented Primary Mrouter Port is not added" ::= { ipmcNewCfgStaticRouteEntry 5} ipmcNewCfgStaticRouteBMrtrBmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The Backup Mrouter ports that are added to this IPMC port bitmap. The selected ports are presented in a bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ Port 9 || || || ||___ Port 8 || |____ Port 7 || . . . ||_________ Port 2 |__________ Port 1 where x : 1 - The represented Backup Mrouter Port is added 0 - The represented Backup Mrouter Port is not added" ::= { ipmcNewCfgStaticRouteEntry 6} ipmcNewCfgStaticRouteAddPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The port to be added to this IPMC route. Next step is using ipmcNewCfgStaticRoutePortInfo leaf in order to make the actual change. When creating a new route, be sure to set Destination IP and Vlan Id before using this leaf." ::= { ipmcNewCfgStaticRouteEntry 7} ipmcNewCfgStaticRouteRemPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The port to be removed from this IPMC route. Not allowed to delete ports that are part of trunks." ::= { ipmcNewCfgStaticRouteEntry 17} ipmcNewCfgStaticRouteTrunks OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The trunk list for this IPMC route. The trunks are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ trunk 8 || || || ||___ trunk 7 || |____ trunk 6 || . . . ||_________ trunk 1 |__________ reserved where x : 1 - The represented trunk belongs to ipmc 0 - The represented trunk does not belong to ipmc" ::= { ipmcNewCfgStaticRouteEntry 8 } ipmcNewCfgStaticRouteAddTrunk OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "The trunk group number to be added to this IPMC route. Next step is using ipmcNewCfgStaticRoutePortInfo leaf in order to make the actual change. A '0' value is returned when read. When creating a new route, be sure to set Destination IP and Vlan Id before using this leaf." ::= { ipmcNewCfgStaticRouteEntry 9 } ipmcNewCfgStaticRouteRemTrunk OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "The trunk group number to be removed from this IPMC route. Next step is using ipmcNewCfgStaticRoutePortInfo leaf in order to make the actual change. A '0' value is returned when read." ::= { ipmcNewCfgStaticRouteEntry 10 } ipmcNewCfgStaticRouteAdminkeys OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The LACP port adminkeys list for to this IPMC route. Adminkeys on five positions alligned to right, separated by commas" ::= { ipmcNewCfgStaticRouteEntry 11 } ipmcNewCfgStaticRouteAddAdminkey OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The LACP port adminkey to be added to this IPMC route. Next step is using ipmcNewCfgStaticRoutePortInfo leaf in order to make the actual change. A '0' value is returned when read. When creating a new route, be sure to set Destination IP and Vlan Id before using this leaf." ::= { ipmcNewCfgStaticRouteEntry 12 } ipmcNewCfgStaticRouteRemAdminkey OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The LACP port adminkey to be removed from this IPMC route. Next step is using ipmcNewCfgStaticRoutePortInfo leaf in order to make the actual change. A '0' value is returned when read." ::= { ipmcNewCfgStaticRouteEntry 13 } ipmcNewCfgStaticRoutePortInfo OBJECT-TYPE SYNTAX INTEGER { host(1), primary(2), backup(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The Port/Trunk/Adminkey Information to be added to this IPMC route (host/primary/backup). Use it only right after you set a new port/trunk/adminkey to specify its type. Warning: If snooping is enabled, primary/backup routes will be converted to host." ::= { ipmcNewCfgStaticRouteEntry 14 } ipmcNewCfgStaticRouteVrid OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The virtual router id of this route." ::= { ipmcNewCfgStaticRouteEntry 15} ipmcNewCfgStaticRouteDelete OBJECT-TYPE SYNTAX INTEGER { delete(2), deletehost(3), deleteprimary(4), deletebackup(5), no(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete this route." ::= { ipmcNewCfgStaticRouteEntry 16} ipmcStaticRouteClearAll OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to clear(2),clears all static IPMC routes. Otherwhise nothing is done." ::= { ipmcStaticRouteCfg 4 } -- -- Static ARP Configuration -- ipStaticArpTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the Static ARP table." ::= { ipStaticArpCfg 1 } ipCurCfgStaticArpTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgStaticArpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of static ARPs in the current configuration block." ::= { ipStaticArpCfg 2 } ipCurCfgStaticArpEntry OBJECT-TYPE SYNTAX IpCurCfgStaticArpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static ARP table" INDEX { ipCurCfgStaticArpIndx } ::= { ipCurCfgStaticArpTable 1 } IpCurCfgStaticArpEntry ::= SEQUENCE { ipCurCfgStaticArpIndx Integer32, ipCurCfgStaticArpIp IpAddress, ipCurCfgStaticArpMAC DisplayString, ipCurCfgStaticArpVlan Integer32, ipCurCfgStaticArpPort PortNumber } ipCurCfgStaticArpIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the static ARP table." ::= { ipCurCfgStaticArpEntry 1} ipCurCfgStaticArpIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address for the ARP entry." ::= { ipCurCfgStaticArpEntry 2} ipCurCfgStaticArpMAC OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address for the ARP entry." ::= { ipCurCfgStaticArpEntry 3 } ipCurCfgStaticArpVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN for the ARP entry." ::= { ipCurCfgStaticArpEntry 4} ipCurCfgStaticArpPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port for the ARP entry." ::= { ipCurCfgStaticArpEntry 5} ipNewCfgStaticArpTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgStaticArpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of static ARPs in the new configuration block." ::= { ipStaticArpCfg 3 } ipNewCfgStaticArpEntry OBJECT-TYPE SYNTAX IpNewCfgStaticArpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static ARP table" INDEX { ipNewCfgStaticArpIndx } ::= { ipNewCfgStaticArpTable 1 } IpNewCfgStaticArpEntry ::= SEQUENCE { ipNewCfgStaticArpIndx Integer32, ipNewCfgStaticArpIp IpAddress, ipNewCfgStaticArpMAC DisplayString, ipNewCfgStaticArpVlan Integer32, ipNewCfgStaticArpPort PortNumber, ipNewCfgStaticArpAction INTEGER } ipNewCfgStaticArpIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the static ARP table." ::= { ipNewCfgStaticArpEntry 1} ipNewCfgStaticArpIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address for the ARP entry." ::= { ipNewCfgStaticArpEntry 2} ipNewCfgStaticArpMAC OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The MAC address for the ARP entry." ::= { ipNewCfgStaticArpEntry 3 } ipNewCfgStaticArpVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The VLAN for the ARP entry." ::= { ipNewCfgStaticArpEntry 4} ipNewCfgStaticArpPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The port for the ARP entry." ::= { ipNewCfgStaticArpEntry 5} ipNewCfgStaticArpAction OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ipNewCfgStaticArpEntry 6 } ipStaticArpClearAll OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to clear(2), clears all static ARP entries. Otherwise nothing is done." ::= { ipStaticArpCfg 4 } -- -- Static NBR Configuration -- ipStaticNbrTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the Static NBR Cache table." ::= { ipStaticNbrCfg 1 } ipCurCfgStaticNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgStaticNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of static NBR Cache entries in the current configuration block." ::= { ipStaticNbrCfg 2 } ipCurCfgStaticNbrEntry OBJECT-TYPE SYNTAX IpCurCfgStaticNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static NBR Cache table" INDEX { ipCurCfgStaticNbrIndx } ::= { ipCurCfgStaticNbrTable 1 } IpCurCfgStaticNbrEntry ::= SEQUENCE { ipCurCfgStaticNbrIndx Integer32, ipCurCfgStaticNbrIp DisplayString, ipCurCfgStaticNbrMAC DisplayString, ipCurCfgStaticNbrVlan Integer32, ipCurCfgStaticNbrPort PortNumber } ipCurCfgStaticNbrIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the static NBR Cache table." ::= { ipCurCfgStaticNbrEntry 1} ipCurCfgStaticNbrIp OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address for the NBR Cache entry." ::= { ipCurCfgStaticNbrEntry 2} ipCurCfgStaticNbrMAC OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address for the NBR Cache entry." ::= { ipCurCfgStaticNbrEntry 3 } ipCurCfgStaticNbrVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN for the NBR Cache entry." ::= { ipCurCfgStaticNbrEntry 4} ipCurCfgStaticNbrPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port for the NBR Cache entry." ::= { ipCurCfgStaticNbrEntry 5} ipNewCfgStaticNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgStaticNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of static NBR Cache entries in the new configuration block." ::= { ipStaticNbrCfg 3 } ipNewCfgStaticNbrEntry OBJECT-TYPE SYNTAX IpNewCfgStaticNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static NBR Cache table" INDEX { ipNewCfgStaticNbrIndx } ::= { ipNewCfgStaticNbrTable 1 } IpNewCfgStaticNbrEntry ::= SEQUENCE { ipNewCfgStaticNbrIndx Integer32, ipNewCfgStaticNbrIp DisplayString, ipNewCfgStaticNbrMAC DisplayString, ipNewCfgStaticNbrVlan Integer32, ipNewCfgStaticNbrPort PortNumber, ipNewCfgStaticNbrAction INTEGER } ipNewCfgStaticNbrIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the static NBR Cache table." ::= { ipNewCfgStaticNbrEntry 1} ipNewCfgStaticNbrIp OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address for the NBR Cache entry." ::= { ipNewCfgStaticNbrEntry 2} ipNewCfgStaticNbrMAC OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The MAC address for the NBR Cache entry." ::= { ipNewCfgStaticNbrEntry 3 } ipNewCfgStaticNbrVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The VLAN for the NBR Cache entry." ::= { ipNewCfgStaticNbrEntry 4} ipNewCfgStaticNbrPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "The port for the NBR Cache entry." ::= { ipNewCfgStaticNbrEntry 5} ipNewCfgStaticNbrAction OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { ipNewCfgStaticNbrEntry 6 } ipStaticNbrClearAll OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to clear(2),clears all static NBR Cache entries. Otherwhise nothing is done." ::= { ipStaticNbrCfg 4 } -- -- IP Static Route6 Configuration -- ipStaticRoute6TableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the Static Route6 table." ::= { ipStaticRoute6Cfg 1 } ipCurCfgStaticRoute6Table OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgStaticRoute6Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of static IP6 routes in the current configuration block." ::= { ipStaticRoute6Cfg 2 } ipCurCfgStaticRoute6Entry OBJECT-TYPE SYNTAX IpCurCfgStaticRoute6Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static IP6 route table" INDEX { ipCurCfgStaticRoute6Indx } ::= { ipCurCfgStaticRoute6Table 1 } IpCurCfgStaticRoute6Entry ::= SEQUENCE { ipCurCfgStaticRoute6Indx Integer32, ipCurCfgStaticRoute6DestIp DisplayString, ipCurCfgStaticRoute6Mask INTEGER, ipCurCfgStaticRoute6Gateway DisplayString, ipCurCfgStaticRoute6Interface Integer32 } ipCurCfgStaticRoute6Indx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the static IP6 routing table." ::= { ipCurCfgStaticRoute6Entry 1} ipCurCfgStaticRoute6DestIp OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP6 address of this route." ::= { ipCurCfgStaticRoute6Entry 2} ipCurCfgStaticRoute6Mask OBJECT-TYPE SYNTAX INTEGER (0..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP6 prefix len of this route." ::= { ipCurCfgStaticRoute6Entry 3} ipCurCfgStaticRoute6Gateway OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP6 address of the gateway for this route." ::= { ipCurCfgStaticRoute6Entry 4} ipCurCfgStaticRoute6Interface OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The IP6 interface of this route. The IP6 address of the specified interface shall be used as source IP when performs routing." ::= { ipCurCfgStaticRoute6Entry 5} ipNewCfgStaticRoute6Table OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgStaticRoute6Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of static IP6 routes in the new configuration block." ::= { ipStaticRoute6Cfg 3 } ipStaticRoute6ClearAllByDestIp OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Clears all static IP6 routes with the specified destination IP6 address." ::= { ipStaticRoute6Cfg 4} ipStaticRoute6ClearAllByGatewayIp OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Clears all static IP6 routes with the specified gateway IP address." ::= { ipStaticRoute6Cfg 5} ipStaticRoute6ClearAllByInterface OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Clears all IP6 routes on the specified inteface number." ::= { ipStaticRoute6Cfg 6} ipStaticRoute6ClearAll OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to clear(2), clears all IP6 static routes. Otherwise nothing is done." ::= { ipStaticRoute6Cfg 7} ipNewCfgStaticRoute6Entry OBJECT-TYPE SYNTAX IpNewCfgStaticRoute6Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the static IP6 route table" INDEX { ipNewCfgStaticRoute6Indx } ::= { ipNewCfgStaticRoute6Table 1 } IpNewCfgStaticRoute6Entry ::= SEQUENCE { ipNewCfgStaticRoute6Indx Integer32, ipNewCfgStaticRoute6DestIp DisplayString, ipNewCfgStaticRoute6Mask INTEGER, ipNewCfgStaticRoute6Gateway DisplayString, ipNewCfgStaticRoute6Action INTEGER, ipNewCfgStaticRoute6Interface Integer32 } ipNewCfgStaticRoute6Indx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the static IP6 routing table." ::= { ipNewCfgStaticRoute6Entry 1} ipNewCfgStaticRoute6DestIp OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "The destination IP6 address of this route. Address should be 16-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { ipNewCfgStaticRoute6Entry 2} ipNewCfgStaticRoute6Mask OBJECT-TYPE SYNTAX INTEGER (0..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The prefix length of this route." ::= { ipNewCfgStaticRoute6Entry 3} ipNewCfgStaticRoute6Gateway OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "The IP6 address of the gateway for this route. Address should be 16-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { ipNewCfgStaticRoute6Entry 4} ipNewCfgStaticRoute6Action OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Set the value '2' to delete the entire route entry. Value 1 (other) is returned when read." ::= { ipNewCfgStaticRoute6Entry 5 } ipNewCfgStaticRoute6Interface OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The IP6 interface of this route. The IP6 address of the specified interface shall be used as source IP when performs routing." ::= { ipNewCfgStaticRoute6Entry 6 } -- -- IPv6 Default Gateway Configuration -- ipGatewayIpv6TableMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the IPv6 gateway table." ::= { ipGatewayIpv6Cfg 1 } ipCurCfgGwIpv6Table OBJECT-TYPE SYNTAX SEQUENCE OF IpCurCfgGwIpv6Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IPv6 gateways in the Current configuration Block." ::= { ipGatewayIpv6Cfg 2 } ipCurCfgGwIpv6Entry OBJECT-TYPE SYNTAX IpCurCfgGwIpv6Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Ipv6 gateway table" INDEX { ipCurCfgGwIpv6Index } ::= { ipCurCfgGwIpv6Table 1 } IpCurCfgGwIpv6Entry ::= SEQUENCE { ipCurCfgGwIpv6Index Integer32, ipCurCfgGwIpv6Addr DisplayString, ipCurCfgGwIpv6State INTEGER } ipCurCfgGwIpv6Index OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 gateway number for which the information is related." ::= { ipCurCfgGwIpv6Entry 1} ipCurCfgGwIpv6Addr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 address of the gateway. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx or fe80:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx%interface" ::= { ipCurCfgGwIpv6Entry 2 } ipCurCfgGwIpv6State OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the default IPv6 gateway." ::= { ipCurCfgGwIpv6Entry 3 } ipNewCfgGwIpv6Table OBJECT-TYPE SYNTAX SEQUENCE OF IpNewCfgGwIpv6Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IPv6 gateways in the new configuration block." ::= { ipGatewayIpv6Cfg 3 } ipNewCfgGwIpv6Entry OBJECT-TYPE SYNTAX IpNewCfgGwIpv6Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the Ipv6 gateway table" INDEX { ipNewCfgGwIpv6Index } ::= { ipNewCfgGwIpv6Table 1 } IpNewCfgGwIpv6Entry ::= SEQUENCE { ipNewCfgGwIpv6Index Integer32, ipNewCfgGwIpv6Addr DisplayString, ipNewCfgGwIpv6State INTEGER, ipNewCfgGwIpv6Delete INTEGER } ipNewCfgGwIpv6Index OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 gateway number for which the information is related." ::= { ipNewCfgGwIpv6Entry 1} ipNewCfgGwIpv6Addr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "The IPv6 address of the gateway. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { ipNewCfgGwIpv6Entry 2 } ipNewCfgGwIpv6State OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state of the default IPv6 gateway." ::= { ipNewCfgGwIpv6Entry 3 } ipNewCfgGwIpv6Delete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the default gw is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect on the state of the default IPv6 gw." ::= { ipNewCfgGwIpv6Entry 4 } -- -- Prefix policy table Configuration -- pptTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the Prefix policy table." ::= { pptCfg 1 } pptCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PPTCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of prefix policy table entries in the current configuration block." ::= { pptCfg 2 } pptCurCfgEntry OBJECT-TYPE SYNTAX PPTCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the prefix policy table" INDEX { pptCurCfgIndx } ::= { pptCurCfgTable 1 } PPTCurCfgEntry ::= SEQUENCE { pptCurCfgIndx Integer32, pptCurCfgPrefix DisplayString, pptCurCfgPrefixLen Integer32, pptCurCfgPrecedence Integer32, pptCurCfgLabel Integer32 } pptCurCfgIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the prefix policy table." ::= { pptCurCfgEntry 1} pptCurCfgPrefix OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The prefix address for the prefix policy table entry." ::= { pptCurCfgEntry 2} pptCurCfgPrefixLen OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The prefix length for the prefix policy table entry." ::= { pptCurCfgEntry 3} pptCurCfgPrecedence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The precedence for the prefix policy table entry." ::= { pptCurCfgEntry 4} pptCurCfgLabel OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The label for the prefix policy table entry." ::= { pptCurCfgEntry 5} pptNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF PPTNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of prefix policy table entries in the new configuration block." ::= { pptCfg 3 } pptNewCfgEntry OBJECT-TYPE SYNTAX PPTNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the prefix policy table" INDEX { pptNewCfgIndx } ::= { pptNewCfgTable 1 } PPTNewCfgEntry ::= SEQUENCE { pptNewCfgIndx Integer32, pptNewCfgPrefix DisplayString, pptNewCfgPrefixLen Integer32, pptNewCfgPrecedence Integer32, pptNewCfgLabel Integer32, pptNewCfgAction INTEGER } pptNewCfgIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the prefix policy table." ::= { pptNewCfgEntry 1} pptNewCfgPrefix OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-create STATUS current DESCRIPTION "The prefix address for the prefix policy table entry." ::= { pptNewCfgEntry 2} pptNewCfgPrefixLen OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The prefix length the prefix policy table entry." ::= { pptNewCfgEntry 3} pptNewCfgPrecedence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The precedence for the prefix policy table entry." ::= { pptNewCfgEntry 4} pptNewCfgLabel OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The label for the prefix policy table entry." ::= { pptNewCfgEntry 5} pptNewCfgAction OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When read, other is returned. Setting the value to anything other than 2(delete) has no effect on the state of the row." ::= { pptNewCfgEntry 6 } mldCurCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "MLD global state." ::= { mldCfg 1 } mldNewCfgState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "MLD global state." ::= { mldCfg 2 } mldCurInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF MldCurInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the interfaces on which MLD is enabled." ::= { mldCfg 3 } mldCurInterfaceEntry OBJECT-TYPE SYNTAX MldCurInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing an interface on which MLD is enabled." INDEX { mldCurInterfaceIfIndex } ::= { mldCurInterfaceTable 1 } MldCurInterfaceEntry ::= SEQUENCE { mldCurInterfaceIfIndex Integer32, mldCurInterfaceQueryInterval INTEGER, mldCurInterfaceVersion INTEGER, mldCurInterfaceQueryMaxResponseIntvl INTEGER, mldCurInterfaceRobustness INTEGER, mldCurInterfaceLastListenQueryIntvl INTEGER, mldCurInterfaceDMrtrEna INTEGER, mldCurInterfaceState INTEGER } mldCurInterfaceIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The internetwork-layer interface value of the interface for which MLD is enabled." ::= { mldCurInterfaceEntry 1 } mldCurInterfaceQueryInterval OBJECT-TYPE SYNTAX INTEGER UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The frequency at which MLD Host-Query packets are transmitted on this interface." DEFVAL { 125 } ::= { mldCurInterfaceEntry 2 } mldCurInterfaceVersion OBJECT-TYPE SYNTAX INTEGER { mldv1(1), mldv2(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The version of MLD which is running on this interface. This object is a place holder to allow for new versions of MLD to be introduced. Version 1 of MLD is defined in RFC 2710." DEFVAL { 1 } ::= { mldCurInterfaceEntry 3 } mldCurInterfaceQueryMaxResponseIntvl OBJECT-TYPE SYNTAX INTEGER UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum query response time advertised in MLD queries on this interface." DEFVAL { 1000 } ::= { mldCurInterfaceEntry 4 } mldCurInterfaceRobustness OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. MLD is robust to (Robustness Variable-1) packet losses. The discussion of the Robustness Variable is in Section 7.1 of RFC 2710." DEFVAL { 2 } ::= { mldCurInterfaceEntry 5 } mldCurInterfaceLastListenQueryIntvl OBJECT-TYPE SYNTAX INTEGER UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The Last Member Query Interval is the Max Response Delay inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages. This value may be tuned to modify the leave latency of the network. A reduced value results in reduced time to detect the loss of the last member of a group." DEFVAL { 1 } ::= { mldCurInterfaceEntry 6 } mldCurInterfaceDMrtrEna OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Dynamic MRouter learning." DEFVAL { 0 } ::= { mldCurInterfaceEntry 7 } mldCurInterfaceState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "State of the MLD interface." DEFVAL { 0 } ::= { mldCurInterfaceEntry 8 } mldNewInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF MldNewInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the interfaces on which MLD is enabled." ::= { mldCfg 4 } mldNewInterfaceEntry OBJECT-TYPE SYNTAX MldNewInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing an interface on which MLD is enabled." INDEX { mldNewInterfaceIfIndex } ::= { mldNewInterfaceTable 1 } MldNewInterfaceEntry ::= SEQUENCE { mldNewInterfaceIfIndex Integer32, mldNewInterfaceQueryInterval INTEGER, mldNewInterfaceVersion INTEGER, mldNewInterfaceQueryMaxResponseIntvl INTEGER, mldNewInterfaceRobustness INTEGER, mldNewInterfaceLastListenQueryIntvl INTEGER, mldNewInterfaceDMrtrEna INTEGER, mldNewInterfaceState INTEGER, mldNewInterfaceDefault INTEGER } mldNewInterfaceIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The internetwork-layer interface value of the interface for which MLD is enabled." ::= { mldNewInterfaceEntry 1 } mldNewInterfaceQueryInterval OBJECT-TYPE SYNTAX INTEGER(2..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The frequency at which MLD Host-Query packets are transmitted on this interface." DEFVAL { 125 } ::= { mldNewInterfaceEntry 2 } mldNewInterfaceVersion OBJECT-TYPE SYNTAX INTEGER { mldv1(1), mldv2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The version of MLD which is running on this interface. This object is a place holder to allow for new versions of MLD to be introduced. Version 1 of MLD is defined in RFC 2710." DEFVAL { 1 } ::= { mldNewInterfaceEntry 3 } mldNewInterfaceQueryMaxResponseIntvl OBJECT-TYPE SYNTAX INTEGER(1000..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum query response time advertised in MLD queries on this interface." DEFVAL { 10000 } ::= { mldNewInterfaceEntry 4 } mldNewInterfaceRobustness OBJECT-TYPE SYNTAX INTEGER(1..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. MLD is robust to (Robustness Variable-1) packet losses. The discussion of the Robustness Variable is in Section 7.1 of RFC 2710." DEFVAL { 2 } ::= { mldNewInterfaceEntry 5 } mldNewInterfaceLastListenQueryIntvl OBJECT-TYPE SYNTAX INTEGER(1..32) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The Last Member Query Interval is the Max Response Delay inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages. This value may be tuned to modify the leave latency of the network. A reduced value results in reduced time to detect the loss of the last member of a group." DEFVAL { 1 } ::= { mldNewInterfaceEntry 6 } mldNewInterfaceDMrtrEna OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Dynamic MRouter learning." DEFVAL { 0 } ::= { mldNewInterfaceEntry 7 } mldNewInterfaceState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "State of the MLD interface." DEFVAL { 0 } ::= { mldNewInterfaceEntry 8 } mldNewInterfaceDefault OBJECT-TYPE SYNTAX INTEGER { other(1), default(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action to set the MLD interface configuration to default. Returns other(1) when read." ::= { mldNewInterfaceEntry 9 } mldDefaultCfgState OBJECT-TYPE SYNTAX INTEGER { other(1), default(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Action to set the global MLD configuration to default. Returns other(1) when read." ::= { mldCfg 5 } -- -- Neighbor Discovery Prefix Configuration -- ndprefixTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the NDPrefix table." ::= { ndprefixCfg 1 } ndprefixCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF NDPREFIXCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ndprefix table entries in the current configuration block." ::= { ndprefixCfg 2 } ndprefixCurCfgEntry OBJECT-TYPE SYNTAX NDPREFIXCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the ndprefix table." INDEX { ndprefixCurCfgIndx } ::= { ndprefixCurCfgTable 1 } NDPREFIXCurCfgEntry ::= SEQUENCE { ndprefixCurCfgIndx INTEGER, ndprefixCurCfgPrefix DisplayString, ndprefixCurCfgPrefixLen INTEGER, ndprefixCurCfgInterfaceIndex Integer32, ndprefixCurCfgProfileIndex INTEGER, ndprefixCurCfgValidLifetime Gauge32, ndprefixCurCfgValidLifetimeFlag INTEGER, ndprefixCurCfgPreferredLifetime Gauge32, ndprefixCurCfgPreferredLifetimeFlag INTEGER, ndprefixCurCfgOnlinkFlag INTEGER, ndprefixCurCfgAutonomousFlag INTEGER, ndprefixCurCfgState INTEGER } ndprefixCurCfgIndx OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ndprefix table." ::= { ndprefixCurCfgEntry 1} ndprefixCurCfgPrefix OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The prefix address for the prefix table entry." ::= { ndprefixCurCfgEntry 2} ndprefixCurCfgPrefixLen OBJECT-TYPE SYNTAX INTEGER (0..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The prefix length for the prefix table entry." ::= { ndprefixCurCfgEntry 3} ndprefixCurCfgInterfaceIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index for the prefix table entry." ::= { ndprefixCurCfgEntry 4} ndprefixCurCfgProfileIndex OBJECT-TYPE SYNTAX INTEGER (0..127) MAX-ACCESS read-only STATUS current DESCRIPTION "The profile index for the prefix table entry Profile 0 is the default profile." ::= { ndprefixCurCfgEntry 5} ndprefixCurCfgValidLifetime OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The Valid lifetime for the prefix table entry." ::= { ndprefixCurCfgEntry 6} ndprefixCurCfgValidLifetimeFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Valid lifetime fixed flag for the prefix table entry." ::= { ndprefixCurCfgEntry 7} ndprefixCurCfgPreferredLifetime OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The Preferred Lifetime for the prefix table entry." ::= { ndprefixCurCfgEntry 8} ndprefixCurCfgPreferredLifetimeFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Preferred Lifetime fixed flag for the prefix table entry." ::= { ndprefixCurCfgEntry 9} ndprefixCurCfgOnlinkFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Onlink flag for the prefix table entry." ::= { ndprefixCurCfgEntry 10} ndprefixCurCfgAutonomousFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Autonomous flag for the prefix table entry." ::= { ndprefixCurCfgEntry 11} ndprefixCurCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state for the prefix table entry." ::= { ndprefixCurCfgEntry 12} ndprefixNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF NDPREFIXNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ndprefix table entries in the new configuration block." ::= { ndprefixCfg 3 } ndprefixNewCfgEntry OBJECT-TYPE SYNTAX NDPREFIXNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the prefix table" INDEX { ndprefixNewCfgIndx } ::= { ndprefixNewCfgTable 1 } NDPREFIXNewCfgEntry ::= SEQUENCE { ndprefixNewCfgIndx Integer32, ndprefixNewCfgPrefix DisplayString, ndprefixNewCfgPrefixLen INTEGER, ndprefixNewCfgInterfaceIndex Integer32, ndprefixNewCfgProfileIndex INTEGER, ndprefixNewCfgValidLifetime Gauge32, ndprefixNewCfgValidLifetimeFlag INTEGER, ndprefixNewCfgPreferredLifetime Gauge32, ndprefixNewCfgPreferredLifetimeFlag INTEGER, ndprefixNewCfgOnlinkFlag INTEGER, ndprefixNewCfgAutonomousFlag INTEGER, ndprefixNewCfgState INTEGER, ndprefixNewCfgAction INTEGER } ndprefixNewCfgIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the prefix table." ::= { ndprefixNewCfgEntry 1} ndprefixNewCfgPrefix OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The prefix address for the prefix table entry." ::= { ndprefixNewCfgEntry 2} ndprefixNewCfgPrefixLen OBJECT-TYPE SYNTAX INTEGER (0..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The prefix length for the prefix table entry." ::= { ndprefixNewCfgEntry 3} ndprefixNewCfgInterfaceIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The interface index for the prefix table entry." ::= { ndprefixNewCfgEntry 4} ndprefixNewCfgProfileIndex OBJECT-TYPE SYNTAX INTEGER (0..127) MAX-ACCESS read-create STATUS current DESCRIPTION "The profile index for the prefix table entry. Profile 0 is the default profile." ::= { ndprefixNewCfgEntry 5} ndprefixNewCfgValidLifetime OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The Valid lifetime for the prefix table entry." ::= { ndprefixNewCfgEntry 6} ndprefixNewCfgValidLifetimeFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The Valid lifetime fixed flag for the prefix table entry." ::= { ndprefixNewCfgEntry 7} ndprefixNewCfgPreferredLifetime OBJECT-TYPE SYNTAX Gauge32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The Preferred Lifetime for the prefix table entry." ::= { ndprefixNewCfgEntry 8} ndprefixNewCfgPreferredLifetimeFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The Preferred Lifetime fixed flag for the prefix table entry." ::= { ndprefixNewCfgEntry 9} ndprefixNewCfgOnlinkFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The Onlink flag for the prefix table entry." ::= { ndprefixNewCfgEntry 10} ndprefixNewCfgAutonomousFlag OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The Autonomous flag for the prefix table entry." ::= { ndprefixNewCfgEntry 11} ndprefixNewCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state for the prefix table entry." ::= { ndprefixNewCfgEntry 12} ndprefixNewCfgAction OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2), deleteall(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "When set to the value of 2 (delete), the entire row is deleted. When set to the value of 3 (deleteall), all entries are deleted. When read, other is returned. Setting the value to anything other than 2(delete) or 3(deleteall) has no effect on the state of the row." ::= { ndprefixNewCfgEntry 13} -- Statistics -- RIPv2 Statistics ripStatInPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP packets received." ::= { rip2Stats 1 } ripStatOutPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP packets transmitted." ::= { rip2Stats 2 } ripStatInRequestPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP requests received." ::= { rip2Stats 3 } ripStatInResponsePkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP response received." ::= { rip2Stats 4 } ripStatOutRequestPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP requests transmitted." ::= { rip2Stats 5 } ripStatOutResponsePkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP responses transmitted." ::= { rip2Stats 6 } ripStatRouteTimeout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP route timeouts." ::= { rip2Stats 7 } ripStatInBadSizePkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of bad size RIP packets received." ::= { rip2Stats 8 } ripStatInBadVersion OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP bad versions received." ::= { rip2Stats 9 } ripStatInBadZeros OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP bad zeros received." ::= { rip2Stats 10 } ripStatInBadSourcePort OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP bad source port received." ::= { rip2Stats 11 } ripStatInBadSourceIP OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP bad source IP received." ::= { rip2Stats 12 } ripStatInSelfRcvPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of RIP packets from self received." ::= { rip2Stats 13 } -- IP statistics ipStatsInReceives OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ip InReceive" ::= { ipStats 1 } ipStatsInHdrErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ip InHdrError" ::= { ipStats 2 } ipStatsInAddrErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ip InAddrErrors" ::= { ipStats 3 } ipStatsInUnknownProtos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ip InUnknownProtos" ::= { ipStats 5 } ipStatsInDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ip InDiscards" ::= { ipStats 6 } ipStatsInDelivers OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ip InDelivers" ::= { ipStats 7 } ipStatsOutRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ip OutRequests" ::= { ipStats 8 } ipStatsOutDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ip OutDiscards" ::= { ipStats 9 } ipStatsDefaultTTL OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ip DefaultTTL" ::= { ipStats 19 } --SNMP statistics nsnmpInPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInPkts" ::= { snmpStats 1 } nsnmpInBadCommunityNames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInBadCommunityNames" ::= { snmpStats 2 } nsnmpInASNParseErrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInASNParseErrs" ::= { snmpStats 3 } nsnmpOutPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutPkts" ::= { snmpStats 4 } nsnmpInTooBigs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInTooBigs" ::= { snmpStats 5 } nsnmpInBadValues OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInBadValues" ::= { snmpStats 6 } nsnmpInGenErrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInGenErrs" ::= { snmpStats 7 } nsnmpInTotalSetVars OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInTotalSetVars" ::= { snmpStats 8 } nsnmpInGetNexts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInGetNexts" ::= { snmpStats 9 } nsnmpInGetResponses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInGetResponses" ::= { snmpStats 10 } nsnmpOutTooBigs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutTooBigs" ::= { snmpStats 11 } nsnmpOutBadValues OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutBadValues" ::= { snmpStats 12 } nsnmpOutGenErrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutGenErrs" ::= { snmpStats 13 } nsnmpOutGetNexts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutGetNexts" ::= { snmpStats 14 } nsnmpOutGetResponses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutGetResponses" ::= { snmpStats 15 } nsnmpSilentDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpSilentDrops" ::= { snmpStats 16 } nsnmpInBadVersions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInBadVersions" ::= { snmpStats 17 } nsnmpInBadCommunityUses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInBadCommunityUses" ::= { snmpStats 18 } nsnmpEnableAuthTraps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpEnableAuthTraps" ::= { snmpStats 19 } nsnmpInBadTypes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInBadTypes" ::= { snmpStats 20 } nsnmpInNoSuchNames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInNoSuchNames" ::= { snmpStats 21 } nsnmpInReadOnlys OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInReadOnlys" ::= { snmpStats 22 } nsnmpInTotalReqVars OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInTotalReqVars" ::= { snmpStats 23 } nsnmpInGetRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInGetRequests" ::= { snmpStats 24 } nsnmpInSetRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInSetRequests" ::= { snmpStats 25 } nsnmpInTraps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpInTraps" ::= { snmpStats 26 } nsnmpOutNoSuchNames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutNoSuchNames" ::= { snmpStats 27 } nsnmpOutReadOnlys OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutReadOnlys" ::= { snmpStats 28 } nsnmpOutGetRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutGetRequests" ::= { snmpStats 29 } nsnmpOutSetRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutSetRequests" ::= { snmpStats 30 } nsnmpOutTraps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpOutTraps" ::= { snmpStats 31 } nsnmpProxyDrops OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "snmpProxyDrops" ::= { snmpStats 32 } -- ICMP statistics icmpStatsInMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InMsgs" ::= { icmpStats 1 } icmpStatsInErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InErrors" ::= { icmpStats 2 } icmpStatsInDestUnreachs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InDestUnreachs" ::= { icmpStats 3 } icmpStatsInTimeExcds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InTimeExcds" ::= { icmpStats 4 } icmpStatsInParmProbs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InParmProbs" ::= { icmpStats 5 } icmpStatsInSrcQuenchs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InSrcQuenchs" ::= { icmpStats 6 } icmpStatsInRedirects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InRedirects" ::= { icmpStats 7 } icmpStatsInEchos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InEchos" ::= { icmpStats 8 } icmpStatsInEchoReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InEchoReps" ::= { icmpStats 9 } icmpStatsInTimestamps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InTimestamps" ::= { icmpStats 10 } icmpStatsInTimestampReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InTimestampReps" ::= { icmpStats 11 } icmpStatsInAddrMasks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InAddrMasks" ::= { icmpStats 12 } icmpStatsInAddrMaskReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp InAddrMaskReps" ::= { icmpStats 13 } icmpStatsOutMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutMsgs" ::= { icmpStats 14 } icmpStatsOutErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutErrors" ::= { icmpStats 15 } icmpStatsOutDestUnreachs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutDestUnreachs" ::= { icmpStats 16 } icmpStatsOutTimeExcds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutTimeExcds" ::= { icmpStats 17 } icmpStatsOutParmProbs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutParmProbs" ::= { icmpStats 18 } icmpStatsOutSrcQuenchs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutSrcQuenchs" ::= { icmpStats 19 } icmpStatsOutRedirects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutRedirects" ::= { icmpStats 20 } icmpStatsOutEchos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutEchos" ::= { icmpStats 21 } icmpStatsOutEchoReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutEchoReps" ::= { icmpStats 22 } icmpStatsOutTimestamps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutTimestamps" ::= { icmpStats 23 } icmpStatsOutTimestampReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutTimestampReps" ::= { icmpStats 24 } icmpStatsOutAddrMasks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutAddrMasks" ::= { icmpStats 25 } icmpStatsOutAddrMaskReps OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "icmp OutAddrMaskReps" ::= { icmpStats 26 } -- TCP statistics tcpStatsRtoAlgorithm OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp RtoAlgorithm" ::= { tcpStats 1 } tcpStatsRtoMin OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp RtoMin" ::= { tcpStats 2 } tcpStatsRtoMax OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp RtoMax" ::= { tcpStats 3 } tcpStatsMaxConn OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp MaxConn" ::= { tcpStats 4 } tcpStatsActiveOpens OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp ActiveOpens" ::= { tcpStats 5 } tcpStatsPassiveOpens OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp PassiveOpens" ::= { tcpStats 6 } tcpStatsAttemptFails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp AttemptFails" ::= { tcpStats 7 } tcpStatsEstabResets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp EstabResets" ::= { tcpStats 8 } tcpStatsInSegs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp InSegs" ::= { tcpStats 9 } tcpStatsOutSegs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp OutSegs" ::= { tcpStats 10 } tcpStatsRetransSegs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp RetransSegs" ::= { tcpStats 11 } tcpStatsInErrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp InErrs" ::= { tcpStats 12 } tcpStatsCurrEstab OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp CurrEstab" ::= { tcpStats 13 } tcpStatsCurrConn OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp CurrConn" ::= { tcpStats 14 } tcpStatsOutRsts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "tcp OutRsts" ::= { tcpStats 15 } -- UDP statistics udpStatsInDatagrams OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "udp InDatagrams" ::= { udpStats 1 } udpStatsOutDatagrams OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "udp OutDatagrams" ::= { udpStats 2 } udpStatsInErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "udp InErrors" ::= { udpStats 3 } udpStatsNoPorts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "udp NoPorts" ::= { udpStats 4 } -- BOOTP statistics bootpRelayStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF BootpRelayStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The BOOTP relay agent statistics." ::= { bootpStats 1 } bootpRelayStatsTableEntry OBJECT-TYPE SYNTAX BootpRelayStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the BOOTP relay agent statistics table." INDEX { bootpRelayStatsIndex } ::= { bootpRelayStatsTable 1 } BootpRelayStatsTableEntry ::= SEQUENCE { bootpRelayStatsIndex PortNumber, bootpRelayStatsRequestsReceived Counter32, bootpRelayStatsRequestsRelayed Counter32, bootpRelayStatsRequestsDroppedNoRelay Counter32, bootpRelayStatsRequestsDroppedNoServer Counter32, bootpRelayStatsRequestsDroppedError Counter32, bootpRelayStatsRepliesReceived Counter32, bootpRelayStatsRepliesRelayed Counter32, bootpRelayStatsRepliesDroppedError Counter32 } bootpRelayStatsIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the port associated with this BOOTP relay statistics entry." ::= { bootpRelayStatsTableEntry 1 } bootpRelayStatsRequestsReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of BOOTP request packets received on the port." ::= { bootpRelayStatsTableEntry 2 } bootpRelayStatsRequestsRelayed OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of request packets relayed to the BOOTP server. If there is more than one server, a request is relayed once for each server; hence, with two servers, this counter will be twice as many as the value of the bootpRelayStatsRequestsReceived object." ::= { bootpRelayStatsTableEntry 3 } bootpRelayStatsRequestsDroppedNoRelay OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter increases each time a request could not be relayed because BOOTP relay is disabled or not allowed on the port." ::= { bootpRelayStatsTableEntry 5 } bootpRelayStatsRequestsDroppedNoServer OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter increases each time a request is dropped because there is no configured server or the server is unreachable because there is no active IP interface that can be used for relaying the request to the server." ::= { bootpRelayStatsTableEntry 6 } bootpRelayStatsRequestsDroppedError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter increases each time a request is dropped due to various errors encountered while processing the request packet. Such errors include short packet length, invalid 'hops' value, and memory allocation errors." ::= { bootpRelayStatsTableEntry 7 } bootpRelayStatsRepliesReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of BOOTP response packets received on the port associated with this object." ::= { bootpRelayStatsTableEntry 8 } bootpRelayStatsRepliesRelayed OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of response packets that were relayed to the client." ::= { bootpRelayStatsTableEntry 9 } bootpRelayStatsRepliesDroppedError OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter increases each time a response packet is dropped due to various errors encountered while processing the packet. Errors include unknown relay agent addresses ('giaddr'), and memory allocation errors." ::= { bootpRelayStatsTableEntry 10 } -- ARP Statistics Group arpStatEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of ARP entries." ::= { arpStats 1 } arpStatHighWater OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The highest number of ARP entries." ::= { arpStats 2 } arpStatMaxEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of ARP entries." ::= { arpStats 3 } -- NBR Statistics nbrStatEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of NBR entries." ::= { nbrStats 1 } nbrStatHighWater OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The highest number of NBR entries." ::= { nbrStats 2 } nbrStatMaxEntries OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of NBR entries." ::= { nbrStats 3} -- ROUTE Statistics Group routeStatEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of IP routes." ::= { routeStats 1 } routeStatHighWater OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The highest number of IP routes." ::= { routeStats 2 } routeStatStaticEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current static routes." ::= { routeStats 3 } routeStatRipEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current RIP routes." ::= { routeStats 4 } routeStatOspfEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current OSPF routes." ::= { routeStats 5 } routeStatBgpEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current BGP routes." ::= { routeStats 6 } routeStatMaxEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of IP routes." ::= { routeStats 7 } routeStatEcmpMaxEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of ECMP routes." ::= { routeStats 8 } routeStatEcmpMaxStaticEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of static ECMP routes." ::= { routeStats 9 } routeStatEcmpPathsEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of routes with ECMP paths." ::= { routeStats 11 } -- DNS Statistics dnsStatInGoodDnsRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of DNS request packets which are received." ::= { dnsStats 1 } dnsStatInBadDnsRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of DNS request packets received that were dropped." ::= { dnsStats 2 } dnsStatOutDnsRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of DNS request packets that have been transmitted." ::= { dnsStats 3 } -- The VRRP Statistics vrrpStatInAdvers OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of good VRRP advertisements which are received." ::= { vrrpStats 1 } vrrpStatOutAdvers OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of good VRRP advertisements which are transmitted." ::= { vrrpStats 2 } vrrpStatBadAdvers OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bad VRRP advertisements which are received." ::= { vrrpStats 3 } vrrpStatBadVersion OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bad VRRP version adv which are received." ::= { vrrpStats 4 } vrrpStatBadAddress OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bad VRRP addres adv which are received." ::= { vrrpStats 5 } vrrpStatBadPassword OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bad VRRP advertisements which are received." ::= { vrrpStats 6 } vrrpStatBadVrid OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bad VRRP version ID adv which are received." ::= { vrrpStats 7 } vrrpStatBadData OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bad VRRP advertisements which are received." ::= { vrrpStats 8 } vrrpStatBadInterval OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of bad VRRP intervals which are received." ::= { vrrpStats 9 } vrrpStatOutGratuitousARPs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of gratuitous ARP packets which are transmitted." ::= { vrrpStats 10 } -- Clear Statistics for ip and ip interface ipClearStats OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(2) results in clearing the IP statistics." ::= { clearStats 1 } vrrpClearStats OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(2) results in clearing the VRRP statistics." ::= { clearStats 2 } ospfClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the OSPF statistics." ::= { clearStats 4 } tcpClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the TCP statistics." ::= { clearStats 5 } udpClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the UDP statistics." ::= { clearStats 6 } dnsClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the DNS statistics." ::= { clearStats 7 } arpClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the ARP statistics." ::= { clearStats 8 } icmpClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the ICMP statistics." ::= { clearStats 9 } routeClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the Route statistics." ::= { clearStats 10 } ipv6ClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the IPv6 statistics." ::= { clearStats 13 } ipv6ClearIcmpStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the ICMP6 statistics." ::= { clearStats 14 } ipv6ClearUdpStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the UDP6 statistics." ::= { clearStats 15 } ospf3ClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the ospf3 statistics." ::= { clearStats 16 } ripClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the RIP statistics." ::= { clearStats 17 } ipv6NbrClearStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the IPv6 nbr statistics." ::= { clearStats 18 } -- Ospf Statistics -- Ospf Statistics for all interfaces and OSPF areas ospfGeneralStats OBJECT IDENTIFIER ::= { ospfStats 1 } ospfCumRxTxStats OBJECT IDENTIFIER ::= { ospfGeneralStats 1 } ospfCumNbrChangeStats OBJECT IDENTIFIER ::= { ospfGeneralStats 2 } ospfCumIntfChangeStats OBJECT IDENTIFIER ::= { ospfGeneralStats 3 } ospfTimersKickOffStats OBJECT IDENTIFIER ::= { ospfGeneralStats 4 } -- Ospf Statistics / Area ospfArea OBJECT IDENTIFIER ::= { ospfStats 2 } ospfAreaRxTxStats OBJECT-TYPE SYNTAX SEQUENCE OF OspfAreaRxTxStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Area Rx/Tx Statistics." ::= { ospfArea 1 } ospfAreaRxTxStatsEntry OBJECT-TYPE SYNTAX OspfAreaRxTxStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Rx Tx packet Statistics about a OSPF area." INDEX { ospfAreaRxTxIndex } ::= { ospfAreaRxTxStats 1 } OspfAreaRxTxStatsEntry ::= SEQUENCE { ospfAreaRxTxIndex Integer32, ospfAreaRxPkts Counter32, ospfAreaTxPkts Counter32, ospfAreaRxHello Counter32, ospfAreaTxHello Counter32, ospfAreaRxDatabase Counter32, ospfAreaTxDatabase Counter32, ospfAreaRxlsReqs Counter32, ospfAreaTxlsReqs Counter32, ospfAreaRxlsAcks Counter32, ospfAreaTxlsAcks Counter32, ospfAreaRxlsUpdates Counter32, ospfAreaTxlsUpdates Counter32 } ospfAreaRxTxIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ospf Area for which these statistics apply." ::= { ospfAreaRxTxStatsEntry 1 } ospfAreaRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of OSPF packets received in this OSPF area." ::= { ospfAreaRxTxStatsEntry 2 } ospfAreaTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of OSPF packets transmitted in this OSPF area." ::= { ospfAreaRxTxStatsEntry 3 } ospfAreaRxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received in this OSPF area." ::= { ospfAreaRxTxStatsEntry 4 } ospfAreaTxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets transmitted in this OSPF area." ::= { ospfAreaRxTxStatsEntry 5 } ospfAreaRxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets transmitted for this OSPF area." ::= { ospfAreaRxTxStatsEntry 6 } ospfAreaTxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets transmitted for this OSPF area." ::= { ospfAreaRxTxStatsEntry 7 } ospfAreaRxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets received for this OSPF area." ::= { ospfAreaRxTxStatsEntry 8 } ospfAreaTxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets transmitted for this OSPF area." ::= { ospfAreaRxTxStatsEntry 9 } ospfAreaRxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets received for this OSPF area." ::= { ospfAreaRxTxStatsEntry 10 } ospfAreaTxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets transmitted for this OSPF area." ::= { ospfAreaRxTxStatsEntry 11 } ospfAreaRxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets received for this OSPF area." ::= { ospfAreaRxTxStatsEntry 12 } ospfAreaTxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets transmitted for this OSPF area." ::= { ospfAreaRxTxStatsEntry 13 } ospfAreaNbrChangeStats OBJECT-TYPE SYNTAX SEQUENCE OF OspfAreaNbrChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Area Neighbour Statistics." ::= { ospfArea 2 } ospfAreaNbrChangeStatsEntry OBJECT-TYPE SYNTAX OspfAreaNbrChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Area Neighbour Change Statistics about a OSPF area." INDEX { ospfAreaNbrIndex } ::= { ospfAreaNbrChangeStats 1 } OspfAreaNbrChangeStatsEntry ::= SEQUENCE { ospfAreaNbrIndex Integer32, ospfAreaNbrhello Counter32, ospfAreaNbrStart Counter32, ospfAreaNbrAdjointOk Counter32, ospfAreaNbrNegotiationDone Counter32, ospfAreaNbrExchangeDone Counter32, ospfAreaNbrBadRequests Counter32, ospfAreaNbrBadSequence Counter32, ospfAreaNbrLoadingDone Counter32, ospfAreaNbrN1way Counter32, ospfAreaNbrRstAd Counter32, ospfAreaNbrDown Counter32, ospfAreaNbrN2way Counter32 } ospfAreaNbrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ospf Area for which these statistics apply." ::= { ospfAreaNbrChangeStatsEntry 1 } ospfAreaNbrhello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received from neighbours in this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 2 } ospfAreaNbrStart OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of neighbours in this state (i.e. an indication that Hello packets should now be sent to the neighbour at intervals of HelloInterval seconds.) in this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 3 } ospfAreaNbrAdjointOk OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of decisions to be made (again) as to whether an adjacency should be established/maintained with the neighbour. for this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 4 } ospfAreaNbrNegotiationDone OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of neighbours in this state wherein the Master/slave relationship has been negotiated, and sequence numbers have been exchanged, for this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 5 } ospfAreaNbrExchangeDone OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of neighbours in this state (i.e. in an adjacency's final state) having transimitted a full sequence of Database Description packets, for this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 6 } ospfAreaNbrBadRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of Link State Requests which have been received for a link state advertisement not contained in the database across this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 7 } ospfAreaNbrBadSequence OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets which have been received that either a) has an unexpected DD sequence number b) Unexpectedly has the init bit set c) Has an options field differing from the last Options field received in a Database Description packet. Any of these conditions indicate that some error has occured during adjacency establishment for this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 8 } ospfAreaNbrLoadingDone OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of link state updates received for all out-of-date portions of the database in this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 9 } ospfAreaNbrN1way OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received from neighbours, in which this router is not mentioned in this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 10 } ospfAreaNbrRstAd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the Neighbour adjacency has been reset across this OPSF area." ::= { ospfAreaNbrChangeStatsEntry 11 } ospfAreaNbrDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Neighbouring routers down (i.e. in the initial state of a neighbour conversation.) in this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 12 } ospfAreaNbrN2way OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received from neighbours, in which this router is mentioned in this OSPF area." ::= { ospfAreaNbrChangeStatsEntry 13 } ospfAreaChangeStats OBJECT-TYPE SYNTAX SEQUENCE OF OspfAreaChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Area Change Statistics." ::= { ospfArea 3 } ospfAreaChangeStatsEntry OBJECT-TYPE SYNTAX OspfAreaChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Area Change Statistics about a OSPF area." INDEX { ospfAreaIntfIndex } ::= { ospfAreaChangeStats 1 } OspfAreaChangeStatsEntry ::= SEQUENCE { ospfAreaIntfIndex Integer32, ospfAreaIntfHello Counter32, ospfAreaIntfDown Counter32, ospfAreaIntfLoop Counter32, ospfAreaIntfUnloop Counter32, ospfAreaIntfWaitTimer Counter32, ospfAreaIntfBackup Counter32, ospfAreaIntfNbrChange Counter32 } ospfAreaIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the OSPF Area for which these statistics apply." ::= { ospfAreaChangeStatsEntry 1 } ospfAreaIntfHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets sent on this OSPF area." ::= { ospfAreaChangeStatsEntry 2 } ospfAreaIntfDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of interfaces down in this OSPF area." ::= { ospfAreaChangeStatsEntry 3 } ospfAreaIntfLoop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of interfaces no longer connected to the attatched network in this OSPF area." ::= { ospfAreaChangeStatsEntry 4 } ospfAreaIntfUnloop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of interfaces connected to the attatched network in this OSPF area.." ::= { ospfAreaChangeStatsEntry 5 } ospfAreaIntfWaitTimer OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the Wait Timer has been fired, (indicating the end of the waiting period that is required before electing a (Backup) Designated Router) for this OSPF area." ::= { ospfAreaChangeStatsEntry 6 } ospfAreaIntfBackup OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Backup Designated Routers on the attatched network for this OSPF area." ::= { ospfAreaChangeStatsEntry 7 } ospfAreaIntfNbrChange OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of changes in the set of bidirectional neighbours associated with the interface in this OSPF area." ::= { ospfAreaChangeStatsEntry 8 } ospfAreaErrorStats OBJECT-TYPE SYNTAX SEQUENCE OF OspfAreaErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Area Error Statistics." ::= { ospfArea 4 } ospfAreaErrorStatsEntry OBJECT-TYPE SYNTAX OspfAreaErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Error Statistics for an OSPF area." INDEX { ospfAreaErrIndex } ::= { ospfAreaErrorStats 1 } OspfAreaErrorStatsEntry ::= SEQUENCE { ospfAreaErrIndex Integer32, ospfAreaErrAuthFailure Counter32, ospfAreaErrNetmaskMismatch Counter32, ospfAreaErrHelloMismatch Counter32, ospfAreaErrDeadMismatch Counter32, ospfAreaErrOptionsMismatch Counter32, ospfAreaErrUnknownNbr Counter32, ospfAreaErrAreaMismatch Counter32, ospfAreaErrInvalidSelfOrigLsa Counter32 } ospfAreaErrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the OSPF Area for which these statistics apply." ::= { ospfAreaErrorStatsEntry 1 } ospfAreaErrAuthFailure OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a wrong password in this area." ::= { ospfAreaErrorStatsEntry 2 } ospfAreaErrNetmaskMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a wrong netmask in this area." ::= { ospfAreaErrorStatsEntry 3 } ospfAreaErrHelloMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different hello interval in this area." ::= { ospfAreaErrorStatsEntry 4 } ospfAreaErrDeadMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different dead interval in this area." ::= { ospfAreaErrorStatsEntry 5 } ospfAreaErrOptionsMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different options in this area." ::= { ospfAreaErrorStatsEntry 6 } ospfAreaErrUnknownNbr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received from an unknown neighbor in this area." ::= { ospfAreaErrorStatsEntry 7 } ospfAreaErrAreaMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a wrong area." ::= { ospfAreaErrorStatsEntry 8 } ospfAreaErrInvalidSelfOrigLsa OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with invalid self originated LSAs." ::= { ospfAreaErrorStatsEntry 9 } -- Ospf Statistics / Interface ospfInterface OBJECT IDENTIFIER ::= { ospfStats 3 } ospfIntfRxTxStats OBJECT-TYPE SYNTAX SEQUENCE OF OspfIntfRxTxStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Interface Rx/Tx packet Statistics." ::= { ospfInterface 1 } ospfIntfRxTxStatsEntry OBJECT-TYPE SYNTAX OspfIntfRxTxStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "OSPF interface Rx/Tx packet statistics." INDEX { ospfIntfRxTxIndex } ::= { ospfIntfRxTxStats 1 } OspfIntfRxTxStatsEntry ::= SEQUENCE { ospfIntfRxTxIndex Integer32, ospfIntfRxPkts Counter32, ospfIntfTxPkts Counter32, ospfIntfRxHello Counter32, ospfIntfTxHello Counter32, ospfIntfRxDatabase Counter32, ospfIntfTxDatabase Counter32, ospfIntfRxlsReqs Counter32, ospfIntfTxlsReqs Counter32, ospfIntfRxlsAcks Counter32, ospfIntfTxlsAcks Counter32, ospfIntfRxlsUpdates Counter32, ospfIntfTxlsUpdates Counter32 } ospfIntfRxTxIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF interface for which these statistics apply." ::= { ospfIntfRxTxStatsEntry 1 } ospfIntfRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of OSPF packets received for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 2 } ospfIntfTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of OSPF packets transmitted for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 3 } ospfIntfRxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 4 } ospfIntfTxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets transmitted for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 5 } ospfIntfRxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets received for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 6 } ospfIntfTxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets transmitted for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 7 } ospfIntfRxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets received for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 8 } ospfIntfTxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets transmitted for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 9 } ospfIntfRxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets received for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 10 } ospfIntfTxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets transmitted for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 11 } ospfIntfRxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets received for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 12 } ospfIntfTxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets transmitted for this OSPF interface." ::= { ospfIntfRxTxStatsEntry 13 } ospfIntfNbrChangeStats OBJECT-TYPE SYNTAX SEQUENCE OF OspfIntfNbrChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Interface Neighbour change Statistics." ::= { ospfInterface 2 } ospfIntfNbrChangeStatsEntry OBJECT-TYPE SYNTAX OspfIntfNbrChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "OSPF interface Neighbour Change statistics." INDEX { ospfIntfNbrIndex } ::= { ospfIntfNbrChangeStats 1 } OspfIntfNbrChangeStatsEntry ::= SEQUENCE { ospfIntfNbrIndex Integer32, ospfIntfNbrhello Counter32, ospfIntfNbrStart Counter32, ospfIntfNbrAdjointOk Counter32, ospfIntfNbrNegotiationDone Counter32, ospfIntfNbrExchangeDone Counter32, ospfIntfNbrBadRequests Counter32, ospfIntfNbrBadSequence Counter32, ospfIntfNbrLoadingDone Counter32, ospfIntfNbrN1way Counter32, ospfIntfNbrRstAd Counter32, ospfIntfNbrDown Counter32, ospfIntfNbrN2way Counter32 } ospfIntfNbrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the OSPF Interface for which these statistics apply." ::= { ospfIntfNbrChangeStatsEntry 1 } ospfIntfNbrhello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received from neighbours in this OSPF interface." ::= { ospfIntfNbrChangeStatsEntry 2 } ospfIntfNbrStart OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of neighbours in this state (i.e. an indication that Hello packets should now be sent to the neighbour at intervals of HelloInterval seconds.) in this OSPF interface." ::= { ospfIntfNbrChangeStatsEntry 3 } ospfIntfNbrAdjointOk OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of decisions to be made (again) as to whether an adjacency should be established/maintained with the neighbour. for this OSPF interface." ::= { ospfIntfNbrChangeStatsEntry 4 } ospfIntfNbrNegotiationDone OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of neighbours in this state wherein the Master/slave relationship has been negotiated, and sequence numbers have been exchanged, for this OSPF interface." ::= { ospfIntfNbrChangeStatsEntry 5 } ospfIntfNbrExchangeDone OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of neighbours in this state (i.e. in an adjacency's final state) having transimitted a full sequence of Database Description packets, for this OSPF interface." ::= { ospfIntfNbrChangeStatsEntry 6 } ospfIntfNbrBadRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Requests which have been received for a link state advertisement not contained in the database for this interface." ::= { ospfIntfNbrChangeStatsEntry 7 } ospfIntfNbrBadSequence OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets which have been received that either a) has an unexpected DD sequence number b) Unexpectedly has the init bit set c) Has an options field differing from the last Options field received in a Database Description packet. Any of these conditions indicate that some error has occured during adjacency establishment for this interface." ::= { ospfIntfNbrChangeStatsEntry 8 } ospfIntfNbrLoadingDone OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of link state updates received for all out-of-date portions of the database for this OSPF interface." ::= { ospfIntfNbrChangeStatsEntry 9 } ospfIntfNbrN1way OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received from neighbours, in which this router is not mentioned for this OSPF interface." ::= { ospfIntfNbrChangeStatsEntry 10 } ospfIntfNbrRstAd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the Neighbour adjacency has been reset on this interface." ::= { ospfIntfNbrChangeStatsEntry 11 } ospfIntfNbrDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Neighbouring routers down (i.e. in the initial state of a neighbour conversation.) for this interface." ::= { ospfIntfNbrChangeStatsEntry 12 } ospfIntfNbrN2way OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received from neighbours, in which this router is mentioned for this OSPF interface." ::= { ospfIntfNbrChangeStatsEntry 13 } ospfIntfChangeStats OBJECT-TYPE SYNTAX SEQUENCE OF OspfIntfChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Interface change Statistics." ::= { ospfInterface 3 } ospfIntfChangeStatsEntry OBJECT-TYPE SYNTAX OspfIntfChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "OSPF interface Change statistics." INDEX { ospfIntfIndex } ::= { ospfIntfChangeStats 1 } OspfIntfChangeStatsEntry ::= SEQUENCE { ospfIntfIndex Integer32, ospfIntfHello Counter32, ospfIntfDown Counter32, ospfIntfLoop Counter32, ospfIntfUnloop Counter32, ospfIntfWaitTimer Counter32, ospfIntfBackup Counter32, ospfIntfNbrChange Counter32 } ospfIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the OSPF Interface for which these statistics apply." ::= { ospfIntfChangeStatsEntry 1 } ospfIntfHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets sent by this interface." ::= { ospfIntfChangeStatsEntry 2 } ospfIntfDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the interface was down." ::= { ospfIntfChangeStatsEntry 3 } ospfIntfLoop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the interface was no longer connected to the attatched network." ::= { ospfIntfChangeStatsEntry 4 } ospfIntfUnloop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the interface, connected back to the attatched network." ::= { ospfIntfChangeStatsEntry 5 } ospfIntfWaitTimer OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the Wait Timer has been fired, (indicating the end of the waiting period that is required before electing a (Backup) Designated Router) for this OSPF interface." ::= { ospfIntfChangeStatsEntry 6 } ospfIntfBackup OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Backup Designated Routers on the attatched network for this OSPF interface." ::= { ospfIntfChangeStatsEntry 7 } ospfIntfNbrChange OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of changes in the set of bidirectional neighbours associated with the interface for this OSPF interface." ::= { ospfIntfChangeStatsEntry 8 } ospfIntfErrorStats OBJECT-TYPE SYNTAX SEQUENCE OF OspfIntfErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Interface Error Statistics." ::= { ospfInterface 4 } ospfIntfErrorStatsEntry OBJECT-TYPE SYNTAX OspfIntfErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Error Statistics for an OSPF area." INDEX { ospfIntfErrIndex } ::= { ospfIntfErrorStats 1 } OspfIntfErrorStatsEntry ::= SEQUENCE { ospfIntfErrIndex Integer32, ospfIntfErrAuthFailure Counter32, ospfIntfErrNetmaskMismatch Counter32, ospfIntfErrHelloMismatch Counter32, ospfIntfErrDeadMismatch Counter32, ospfIntfErrOptionsMismatch Counter32, ospfIntfErrUnknownNbr Counter32, ospfIntfErrAreaMismatch Counter32, ospfIntfErrInvalidSelfOrigLSA Counter32 } ospfIntfErrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the OSPF Intf for which these statistics apply." ::= { ospfIntfErrorStatsEntry 1 } ospfIntfErrAuthFailure OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a wrong password in this area." ::= { ospfIntfErrorStatsEntry 2 } ospfIntfErrNetmaskMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a wrong netmask in this area." ::= { ospfIntfErrorStatsEntry 3 } ospfIntfErrHelloMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different hello interval in this area." ::= { ospfIntfErrorStatsEntry 4 } ospfIntfErrDeadMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different dead interval in this area." ::= { ospfIntfErrorStatsEntry 5 } ospfIntfErrOptionsMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different options in this area." ::= { ospfIntfErrorStatsEntry 6 } ospfIntfErrUnknownNbr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received from an unknown neighbor in this area." ::= { ospfIntfErrorStatsEntry 7 } ospfIntfErrAreaMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a wrong area." ::= { ospfIntfErrorStatsEntry 8 } ospfIntfErrInvalidSelfOrigLSA OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with invalid self-orig LSAs." ::= { ospfIntfErrorStatsEntry 9 } -- Ospf General Statistics contains the cumulative stats for all -- areas / interfaces ospfCumRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all OSPF packets received on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 1 } ospfCumTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all OSPF packets transmitted on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 2 } ospfCumRxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Hello packets received on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 3 } ospfCumTxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Hello packets transmitted on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 4 } ospfCumRxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Database Description packets received on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 5 } ospfCumTxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Database Description packets transmitted on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 6 } ospfCumRxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Link State Request packets received on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 7 } ospfCumTxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Link State Request packets transmitted on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 8 } ospfCumRxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Link State Acknowledgement packets received on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 9 } ospfCumTxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Link State Acknowledgement packets transmitted on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 10 } ospfCumRxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Link State Update packets received on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 11 } ospfCumTxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Link State Update packets transmitted on all OSPF areas and interfaces." ::= { ospfCumRxTxStats 12 } ospfCumNbrhello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of all Hello packets received from neighbours on all OSPF areas and interfaces." ::= { ospfCumNbrChangeStats 1 } ospfCumNbrStart OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of neighbours in this state (i.e. an indication that Hello packets should now be sent to the neighbour at intervals of HelloInterval seconds.) across all OSPF areas and interfaces." ::= { ospfCumNbrChangeStats 2 } ospfCumNbrAdjointOk OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of decisions to be made (again) as to whether an adjacency should be established/maintained with the neighbour across all OSPF areas and interfaces." ::= { ospfCumNbrChangeStats 3 } ospfCumNbrNegotiationDone OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of neighbours in this state wherein the Master/slave relationship has been negotiated, and sequence numbers have been exchanged, across all OSPF areas and interfaces." ::= { ospfCumNbrChangeStats 4 } ospfCumNbrExchangeDone OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of neighbours in this state (i.e. in an adjacency's final state) having transimitted a full sequence of Database Description packets, across all OSPF areas and interfaces." ::= { ospfCumNbrChangeStats 5 } ospfCumNbrBadRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of Link State Requests which have been received for a link state advertisement not contained in the database across all interfaces and OSPF areas." ::= { ospfCumNbrChangeStats 6 } ospfCumNbrBadSequence OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of Database Description packets which have been received that either a) has an unexpected DD sequence number b) Unexpectedly has the init bit set c) Has an options field differing from the last Options field received in a Database Description packet. Any of these conditions indicate that some error has occured during adjacency establishment for all OSPF areas and interfaces." ::= { ospfCumNbrChangeStats 7 } ospfCumNbrLoadingDone OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of link state updates received for all out-of-date portions of the database across all OSPF areas and interfaces." ::= { ospfCumNbrChangeStats 8 } ospfCumNbrN1way OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of Hello packets received from neighbours, in which this router is not mentioned across all OSPF interfaces and areas." ::= { ospfCumNbrChangeStats 9 } ospfCumNbrRstAd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the Neighbour adjacency has been reset across all OPSF areas and interfaces." ::= { ospfCumNbrChangeStats 10 } ospfCumNbrDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Neighbouring routers down (i.e. in the initial state of a neighbour conversation.) across all OSPF areas and interfaces." ::= { ospfCumNbrChangeStats 11 } ospfCumNbrN2way OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of Hello packets received from neighbours, in which this router is mentioned across all OSPF interfaces and areas." ::= { ospfCumNbrChangeStats 12 } ospfCumIntfHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of Hello packets sent on all interfaces and areas" ::= { ospfCumIntfChangeStats 1 } ospfCumIntfDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of interfaces down in all OSPF areas." ::= { ospfCumIntfChangeStats 2 } ospfCumIntfLoop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total of interfaces no longer connected to the attatched network across all OSPF areas and interfaces." ::= { ospfCumIntfChangeStats 3 } ospfCumIntfUnloop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of interfaces, connected to the attatched network in all OSPF areas." ::= { ospfCumIntfChangeStats 4 } ospfCumIntfWaitTimer OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the Wait Timer has been fired, (indicating the end of the waiting period that is required before electing a (Backup) Designated Router) across all OSPF areas and interfaces." ::= { ospfCumIntfChangeStats 5 } ospfCumIntfBackup OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of Backup Designated Routers on the attatched network for all OSPF areas and interfaces." ::= { ospfCumIntfChangeStats 6 } ospfCumIntfNbrChange OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of changes in the set of bidirectional neighbours associated with any interface across all OSPF areas." ::= { ospfCumIntfChangeStats 7 } ospfTmrsKckOffHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the Hello timer has been fired (which triggers the send of a Hello packet) across all OPSF areas and interfaces." ::= { ospfTimersKickOffStats 1 } ospfTmrsKckOffRetransmit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the Retransmit timer has been fired across all OPSF areas and interfaces." ::= { ospfTimersKickOffStats 2 } ospfTmrsKckOffLsaLock OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the Lsa Lock timer has been fired across all OSPF areas and interfaces." ::= { ospfTimersKickOffStats 3 } ospfTmrsKckOffLsaAck OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the Lsa Ack timer has been fired across all ospf areas and interfaces." ::= { ospfTimersKickOffStats 4 } ospfTmrsKckOffDbage OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the Dbage has been fired." ::= { ospfTimersKickOffStats 5 } ospfTmrsKckOffSummary OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the Summary timer has been fired." ::= { ospfTimersKickOffStats 6 } ospfTmrsKckOffAseExport OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the ASE Export timer has been fired." ::= { ospfTimersKickOffStats 7 } -- IGMP Snooping statistics igmpSnoopStats OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics for IGMP Snooping." ::= { igmpStats 1 } igmpSnoopStatsEntry OBJECT-TYPE SYNTAX IgmpSnoopStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics for IGMP Snooping." INDEX { igmpSnoopVlanIndex } ::= { igmpSnoopStats 1 } IgmpSnoopStatsEntry ::= SEQUENCE { igmpSnoopVlanIndex INTEGER, rxIgmpValidPkts Counter32, rxIgmpInvalidPkts Counter32, rxIgmpGenQueries Counter32, rxIgmpGrpSpecificQueries Counter32, rxIgmpLeaves Counter32, rxIgmpDiscardPkts Counter32, rxIgmpReports Counter32, rxIgmpPimHellos Counter32, txIgmpGenQueries Counter32, txIgmpGrpSpecificQueries Counter32, txIgmpReports Counter32, igmpClearVlanStats INTEGER, txIgmpLeaves Counter32, rxIgmpGroupSourceSpecificQueries Counter32, rxIgmpV3CurrentStateRecords Counter32, rxIgmpV3SourceListChangeRecords Counter32, rxIgmpV3FilterChangeRecords Counter32 } igmpSnoopVlanIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the VLAN for which these statistics apply." ::= { igmpSnoopStatsEntry 1 } rxIgmpValidPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of valid IGMP packets received on this VLAN." ::= { igmpSnoopStatsEntry 2 } rxIgmpInvalidPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of invalid IGMP packets received on this VLAN." ::= { igmpSnoopStatsEntry 3 } rxIgmpGenQueries OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP General Query packets received on this VLAN." ::= { igmpSnoopStatsEntry 4 } rxIgmpGrpSpecificQueries OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP Group Specific Query packets received on this VLAN." ::= { igmpSnoopStatsEntry 5 } rxIgmpLeaves OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP Leave packets received on this VLAN." ::= { igmpSnoopStatsEntry 6 } rxIgmpReports OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP Report packets received on this VLAN." ::= { igmpSnoopStatsEntry 7 } txIgmpGrpSpecificQueries OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP Group Specific Query packets transmitted on this VLAN." ::= { igmpSnoopStatsEntry 8 } txIgmpReports OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP Report packets transmitted on this VLAN." ::= { igmpSnoopStatsEntry 9 } txIgmpLeaves OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP Leave packets transmitted on this VLAN." ::= { igmpSnoopStatsEntry 10 } rxIgmpGroupSourceSpecificQueries OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP Group Source Specific (GSSQ) Queries received on this VLAN." ::= { igmpSnoopStatsEntry 11 } rxIgmpV3CurrentStateRecords OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP Current State Records (CSRs) received on this VLAN." ::= { igmpSnoopStatsEntry 12 } rxIgmpV3SourceListChangeRecords OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP Source List Change Records (SLCRs) received on this VLAN." ::= { igmpSnoopStatsEntry 13 } rxIgmpV3FilterChangeRecords OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP Filter Mode Change Records (FMCRs) received on this VLAN." ::= { igmpSnoopStatsEntry 14 } txIgmpGenQueries OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP General Query packets send on this VLAN." ::= { igmpSnoopStatsEntry 16 } rxIgmpDiscardPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP packets discarded on this VLAN." ::= { igmpSnoopStatsEntry 17 } rxIgmpPimHellos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Pim Hello packets received on this VLAN." ::= { igmpSnoopStatsEntry 18 } igmpClearVlanStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the statistics for this snooping VLAN." ::= { igmpSnoopStatsEntry 19 } igmpClearAllStats OBJECT-TYPE SYNTAX INTEGER { clear(1), ok(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to clear(1) results in clearing the IGMP statistics." ::= { igmpStats 2 } igmpStatsTotalIgmpGroups OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP groups." ::= { igmpStats 3 } igmpStatsTotalIpmcGroups OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IPMC groups." ::= { igmpStats 4 } ipv6InReceives OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of input datagrams received from interfaces, including those received in error." ::= { ipv6Stats 1 } ipv6InMcasts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of multicast packets received from interfaces, including those received in error." ::= { ipv6Stats 2 } ipv6InDelivers OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams given to upper layer - ICMP/UDP" ::= { ipv6Stats 3 } ipv6InDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams discarded despite no errors" ::= { ipv6Stats 4 } ipv6InHdrerrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams with error in IPv6/Option headers" ::= { ipv6Stats 5 } ipv6InAddrerrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams with error in destination address" ::= { ipv6Stats 6 } ipv6InUnkprots OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams with unknown/unsupported protocol" ::= { ipv6Stats 7 } ipv6InTruncs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams with insufficient data" ::= { ipv6Stats 8 } ipv6OutMcasts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total sent multicast pkts" ::= { ipv6Stats 10 } ipv6ForwDgrams OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams attempted to be forwarded" ::= { ipv6Stats 11 } ipv6TooBigerrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams which could not be forwarded as their size exceeds (Path) MTU" ::= { ipv6Stats 12 } ipv6OutReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams attempted to be sent" ::= { ipv6Stats 13 } ipv6OutDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total outgoing Datagrams discarded despite no errors" ::= { ipv6Stats 14 } ipv6OutNorts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams discarded due to no routes" ::= { ipv6Stats 15 } ipv6Reasmreqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams needing reassembly" ::= { ipv6Stats 16 } ipv6Reasmoks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams successfully reassembled" ::= { ipv6Stats 17 } ipv6Reasmfails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams for witch reassembly failured" ::= { ipv6Stats 18 } ipv6Fragoks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams successfully fragmented" ::= { ipv6Stats 19 } ipv6Fragfails OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total datagrams for witch fragmentation failured" ::= { ipv6Stats 20 } ipv6Fragcreates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of fragments created" ::= { ipv6Stats 21 } ipv6InNsols OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of received Neighbor Solicitations" ::= { ipv6Stats 22 } ipv6InNadvs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of received Neighbor Advertisements" ::= { ipv6Stats 23 } ipv6InRoutsols OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of received Router Solicitations" ::= { ipv6Stats 25 } ipv6InRoutadvs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of received Router Advertisements" ::= { ipv6Stats 26 } ipv6InRoutRedirs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of received Router Redirect messages" ::= { ipv6Stats 27 } ipv6OutNsols OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of sent Neighbor Solicitations" ::= { ipv6Stats 28 } ipv6OutNadvs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of sent Neighbor Advertisements" ::= { ipv6Stats 29 } ipv6OutRoutadvs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of sent Router Advertisements" ::= { ipv6Stats 30 } ipv6OutRedirs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of sent Redirects" ::= { ipv6Stats 31 } ipv6OutRoutSols OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of sent Router Solicitations" ::= { ipv6Stats 32 } -- Please see tIp6If structure: u4RaSchedTime and u4RaSentTime are interface -- parameters. They are not part of interface statistics (tIp6IfStats stats;). -- ipv6RaSchedTime OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Next multicast Router Advertisement scheduled time" -- ::= { ipv6Stats 36 } -- ipv6RaSentTime OBJECT-TYPE -- SYNTAX Counter32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Last Router Advertisement sent time" -- ::= { ipv6Stats 37 } ipv6icmpInMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ICMP messages received." ::= { ipv6Stats 39 } ipv6icmpInErrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ICMP messages attempted to send." ::= { ipv6Stats 40 } ipv6icmpInBadcode OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ICMP messages in bad code." ::= { ipv6Stats 41 } ipv6icmpInToobig OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP too big messages received." ::= { ipv6Stats 42 } ipv6icmpInDstUnreach OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Destination Unreachable messages received." ::= { ipv6Stats 43 } ipv6icmpInTmexceeded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Time Exceeded messages received." ::= { ipv6Stats 44 } ipv6icmpInParamprob OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Parameter Problem messages received." ::= { ipv6Stats 45 } ipv6icmpInEchoReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Echo request messages received." ::= { ipv6Stats 46 } ipv6icmpInEchoResp OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Echo Reply messages received." ::= { ipv6Stats 47 } ipv6icmpOutMsgs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of ICMP messages which this entity attempted to send." ::= { ipv6Stats 48 } ipv6icmpOutErrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers." ::= { ipv6Stats 49 } ipv6icmpOutDstUnreach OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Destination Unreachable messages sent." ::= { ipv6Stats 50 } ipv6icmpOutToobig OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP too big messages sent." ::= { ipv6Stats 51 } ipv6icmpOutTmexceeded OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Time Exceeded messages sent." ::= { ipv6Stats 52 } ipv6icmpOutParamprob OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Parameter Problem messages sent." ::= { ipv6Stats 53 } ipv6icmpOutEchoReq OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Echo request messages sent." ::= { ipv6Stats 54 } ipv6icmpOutEchoResp OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Echo Reply messages sent." ::= { ipv6Stats 55 } ipv6icmpInRouterSol OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP router solicitations received." ::= { ipv6Stats 56 } ipv6icmpInRouterAdv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP router advertisements received." ::= { ipv6Stats 57 } ipv6icmpInNeighSol OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP neighbor solicitations received." ::= { ipv6Stats 58 } ipv6icmpInNeighAdv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP neighbor advertisements received." ::= { ipv6Stats 59 } ipv6icmpInRedir OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Redirect messages received." ::= { ipv6Stats 60 } ipv6icmpOutRouterSol OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP router solicitations sent." ::= { ipv6Stats 61 } ipv6icmpOutRouterAdv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP router advertisements sent." ::= { ipv6Stats 62 } ipv6icmpOutNeighSol OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP neighbor solicitations sent." ::= { ipv6Stats 63 } ipv6icmpOutNeighAdv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP neighbor advertisements sent." ::= { ipv6Stats 64 } ipv6icmpOutRedir OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ICMP Redirect messages sent." ::= { ipv6Stats 65 } ipv6udpInDgrams OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of UDP received datagrams." ::= { ipv6Stats 66 } ipv6udpInErrs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of UDP error encountered during processing of packet." ::= { ipv6Stats 67 } ipv6udpOutDgrams OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of UDP datagrams passed to IP6 layer." ::= { ipv6Stats 68 } ipv6udpNumPorts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of UDP ports that are currently open." ::= { ipv6Stats 69 } ipv6icmpInAdminProhib OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received Destination Unreachable ICMP packets." ::= { ipv6Stats 70 } ipv6icmpOutAdminProhib OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of sent Destination Unreachable ICMP packets." ::= { ipv6Stats 71 } -- Ospf3 Statistics -- Ospf3 Statistics for all interfaces and Ospf3 areas ospf3GeneralStats OBJECT IDENTIFIER ::= { ospf3Stats 1 } ospf3CumRxTxDisdStats OBJECT IDENTIFIER ::= { ospf3GeneralStats 1 } ospf3CumNbrChangeStats OBJECT IDENTIFIER ::= { ospf3GeneralStats 2 } ospf3CumIntfChangeStats OBJECT IDENTIFIER ::= { ospf3GeneralStats 3 } ospf3TimersKickOffStats OBJECT IDENTIFIER ::= { ospf3GeneralStats 4 } -- Ospf3 Statistics / Area ospf3Area OBJECT IDENTIFIER ::= { ospf3Stats 2 } ospf3AreaRxTxDisdStats OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3AreaRxTxDisdStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Ospf3 Area Rx/Tx Statistics." ::= { ospf3Area 1 } ospf3AreaRxTxDisdStatsEntry OBJECT-TYPE SYNTAX Ospf3AreaRxTxDisdStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Rx Tx packet Statistics about a Ospf3 area." INDEX { ospf3AreaRxTxDisdIndex } ::= { ospf3AreaRxTxDisdStats 1 } Ospf3AreaRxTxDisdStatsEntry ::= SEQUENCE { ospf3AreaRxTxDisdIndex Integer32, ospf3AreaRxPkts Counter32, ospf3AreaTxPkts Counter32, ospf3AreaDisdPkts Counter32, ospf3AreaRxHello Counter32, ospf3AreaTxHello Counter32, ospf3AreaDisdHello Counter32, ospf3AreaRxDatabase Counter32, ospf3AreaTxDatabase Counter32, ospf3AreaDisdDatabase Counter32, ospf3AreaRxlsReqs Counter32, ospf3AreaTxlsReqs Counter32, ospf3AreaDisdlsReqs Counter32, ospf3AreaRxlsAcks Counter32, ospf3AreaTxlsAcks Counter32, ospf3AreaDisdlsAcks Counter32, ospf3AreaRxlsUpdates Counter32, ospf3AreaTxlsUpdates Counter32, ospf3AreaDisdlsUpdates Counter32 } ospf3AreaRxTxDisdIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ospf3 Area for which these statistics apply." ::= { ospf3AreaRxTxDisdStatsEntry 1 } ospf3AreaRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Ospf3 packets received in this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 2 } ospf3AreaTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Ospf3 packets transmitted in this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 3 } ospf3AreaDisdPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Ospf3 packets discaded in this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 4 } ospf3AreaRxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received in this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 5 } ospf3AreaTxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets transmitted in this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 6 } ospf3AreaDisdHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets discaded in this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 7 } ospf3AreaRxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets transmitted for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 8 } ospf3AreaTxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets transmitted for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 9 } ospf3AreaDisdDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets discarded for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 10 } ospf3AreaRxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets received for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 11 } ospf3AreaTxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets transmitted for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 12 } ospf3AreaDisdlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets discarded for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 13 } ospf3AreaRxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets received for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 14 } ospf3AreaTxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets transmitted for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 15 } ospf3AreaDisdlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets discarded for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 16 } ospf3AreaRxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets received for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 17 } ospf3AreaTxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets transmitted for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 18 } ospf3AreaDisdlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets discarded for this Ospf3 area." ::= { ospf3AreaRxTxDisdStatsEntry 19 } ospf3AreaNbrChangeStats OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3AreaNbrChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Ospf3 Neighbor change Statistics." ::= { ospf3Area 2 } ospf3AreaNbrChangeStatsEntry OBJECT-TYPE SYNTAX Ospf3AreaNbrChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ospf3 Neighbor Change statistics." INDEX { ospf3AreaNbrIndex } ::= { ospf3AreaNbrChangeStats 1 } Ospf3AreaNbrChangeStatsEntry ::= SEQUENCE { ospf3AreaNbrIndex Integer32, ospf3AreaNbrDown Counter32, ospf3AreaNbrAttempt Counter32, ospf3AreaNbrInit Counter32, ospf3AreaNbrN2way Counter32, ospf3AreaNbrExStart Counter32, ospf3AreaNbrExchange Counter32, ospf3AreaNbrLoading Counter32, ospf3AreaNbrFull Counter32, ospf3AreaNbrAllEvents Counter32 } ospf3AreaNbrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the Ospf3 Area for which these statistics apply." ::= { ospf3AreaNbrChangeStatsEntry 1 } ospf3AreaNbrDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this area have changed into DOWN state." ::= { ospf3AreaNbrChangeStatsEntry 2 } ospf3AreaNbrAttempt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this area have changed into ATTEMPT state." ::= { ospf3AreaNbrChangeStatsEntry 3 } ospf3AreaNbrInit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this area have changed into INIT state." ::= { ospf3AreaNbrChangeStatsEntry 4 } ospf3AreaNbrN2way OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this area have changed into 2WAY state." ::= { ospf3AreaNbrChangeStatsEntry 5 } ospf3AreaNbrExStart OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this area have changed into EXSTART state." ::= { ospf3AreaNbrChangeStatsEntry 6 } ospf3AreaNbrExchange OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this area have changed into EXCHANGE state." ::= { ospf3AreaNbrChangeStatsEntry 7 } ospf3AreaNbrLoading OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this area have changed into LOADING state." ::= { ospf3AreaNbrChangeStatsEntry 8 } ospf3AreaNbrFull OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this area have changed into FULL state." ::= { ospf3AreaNbrChangeStatsEntry 9 } ospf3AreaNbrAllEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this area have changed state or an error had occured." ::= { ospf3AreaNbrChangeStatsEntry 10 } ospf3AreaIntfChangeStats OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3AreaIntfChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Ospf3 Interface change Statistics." ::= { ospf3Area 3 } ospf3AreaIntfChangeStatsEntry OBJECT-TYPE SYNTAX Ospf3AreaIntfChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ospf3 interface Change statistics." INDEX { ospf3AreaIntfIndex } ::= { ospf3AreaIntfChangeStats 1 } Ospf3AreaIntfChangeStatsEntry ::= SEQUENCE { ospf3AreaIntfIndex Integer32, ospf3AreaIntfDown Counter32, ospf3AreaIntfLoop Counter32, ospf3AreaIntfWaiting Counter32, ospf3AreaIntfPtop Counter32, ospf3AreaIntfDr Counter32, ospf3AreaIntfBackup Counter32, ospf3AreaIntfDrOther Counter32, ospf3AreaIntfAllEvents Counter32 } ospf3AreaIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the Ospf3 Interface for which these statistics apply." ::= { ospf3AreaIntfChangeStatsEntry 1 } ospf3AreaIntfDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of changes into the DOWN State of the interfaces associated with this OSPF area." ::= { ospf3AreaIntfChangeStatsEntry 2 } ospf3AreaIntfLoop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of changes into the LOOP State of the interfaces associated with this OSPF area." ::= { ospf3AreaIntfChangeStatsEntry 3 } ospf3AreaIntfWaiting OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of changes into the WAITING State of the interfaces associated with this OSPF area." ::= { ospf3AreaIntfChangeStatsEntry 4 } ospf3AreaIntfPtop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of changes into the PTOP State of the interfaces associated with this OSPF area." ::= { ospf3AreaIntfChangeStatsEntry 5 } ospf3AreaIntfDr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of changes into the DR State of the interfaces associated with this OSPF area." ::= { ospf3AreaIntfChangeStatsEntry 6 } ospf3AreaIntfBackup OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of changes into the BACKUP State of the interfaces associated with this OSPF area." ::= { ospf3AreaIntfChangeStatsEntry 7 } ospf3AreaIntfDrOther OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of changes into the DROTHER State of the interfaces associated with this OSPF area." ::= { ospf3AreaIntfChangeStatsEntry 8 } ospf3AreaIntfAllEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of State changes of the interfaces associated with this OSPF area" ::= { ospf3AreaIntfChangeStatsEntry 9 } ospf3AreaErrorStats OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3AreaErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Ospf3 Interface Error Statistics." ::= { ospf3Area 4 } ospf3AreaErrorStatsEntry OBJECT-TYPE SYNTAX Ospf3AreaErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Error Statistics for an Ospf3 area." INDEX { ospf3AreaErrIndex } ::= { ospf3AreaErrorStats 1 } Ospf3AreaErrorStatsEntry ::= SEQUENCE { ospf3AreaErrIndex Integer32, ospf3AreaErrRxOnPasv Counter32, ospf3AreaErrRxOspfOff Counter32, ospf3AreaErrRxOnNotup Counter32, ospf3AreaErrRxVerMismatch Counter32, ospf3AreaErrRxZeroRTRID Counter32, ospf3AreaErrRxSameRTRID Counter32, ospf3AreaErrRxMismatchInstID Counter32, ospf3AreaErrBadAreaID Counter32, ospf3AreaErrBadDestAddr Counter32, ospf3AreaErrBadChecksum Counter32, ospf3AreaErrBadNeighbour Counter32, ospf3AreaErrBadPktType Counter32, ospf3AreaErrHelloMismatch Counter32, ospf3AreaErrOptionsMismatch Counter32, ospf3AreaErrDeadMismatch Counter32, ospf3AreaErrHelloNoNbr Counter32 } ospf3AreaErrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the Ospf3 Area for which these statistics apply." ::= { ospf3AreaErrorStatsEntry 1 } ospf3AreaErrRxOnPasv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by all of the interfaces in this area that are received on a passive interface." ::= { ospf3AreaErrorStatsEntry 2 } ospf3AreaErrRxOspfOff OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by all of the interfaces in this area that are received while OSPF was disabled." ::= { ospf3AreaErrorStatsEntry 3 } ospf3AreaErrRxOnNotup OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by all of the interfaces in this area that are received while the interface was disabled." ::= { ospf3AreaErrorStatsEntry 4 } ospf3AreaErrRxVerMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by all of the interfaces in this area that have an OSPF version number not equal to the one of the interface." ::= { ospf3AreaErrorStatsEntry 5 } ospf3AreaErrRxZeroRTRID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by all of the interfaces in this area that have a RouterID of 0." ::= { ospf3AreaErrorStatsEntry 6 } ospf3AreaErrRxSameRTRID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by all of the interfaces in this area that have the same RouterID as this Router." ::= { ospf3AreaErrorStatsEntry 7 } ospf3AreaErrRxMismatchInstID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by all of the interfaces in this area that have an instance number not equal to the one of the interface." ::= { ospf3AreaErrorStatsEntry 8 } ospf3AreaErrBadAreaID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by all of the interfaces in this area that have an area number not equal to the one of the area of the interface." ::= { ospf3AreaErrorStatsEntry 9 } ospf3AreaErrBadDestAddr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets discarded by all of the interfaces in this area because of a destination address mismatch." ::= { ospf3AreaErrorStatsEntry 10 } ospf3AreaErrBadChecksum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets discarded by all of the interfaces in this area because of a bad checksum." ::= { ospf3AreaErrorStatsEntry 11 } ospf3AreaErrBadNeighbour OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets discarded by all of the interfaces in this area because they could not be associated with any neighbor." ::= { ospf3AreaErrorStatsEntry 12 } ospf3AreaErrBadPktType OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets discarded by all of the interfaces in this area because the packet type was not recognized." ::= { ospf3AreaErrorStatsEntry 13 } ospf3AreaErrHelloMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different hello interval by all of the interfaces in this area ." ::= { ospf3AreaErrorStatsEntry 14 } ospf3AreaErrOptionsMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different options by all of the interfaces in this area ." ::= { ospf3AreaErrorStatsEntry 15 } ospf3AreaErrDeadMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different dead interval in this area." ::= { ospf3AreaErrorStatsEntry 16 } ospf3AreaErrHelloNoNbr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received from an unknown neighbor when all of the interfaces in this area has a Network Type of NBMA or PTOMP." ::= { ospf3AreaErrorStatsEntry 17 } -- Ospf3 Statistics / Interface ospf3Interface OBJECT IDENTIFIER ::= { ospf3Stats 3 } ospf3IntfRxTxDisdStats OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3IntfRxTxDisdStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Ospf3 Intf Rx/Tx Statistics." ::= { ospf3Interface 1 } ospf3IntfRxTxDisdStatsEntry OBJECT-TYPE SYNTAX Ospf3IntfRxTxDisdStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Rx Tx packet Statistics about a Ospf3 area." INDEX { ospf3IntfRxTxDisdIndex } ::= { ospf3IntfRxTxDisdStats 1 } Ospf3IntfRxTxDisdStatsEntry ::= SEQUENCE { ospf3IntfRxTxDisdIndex Integer32, ospf3IntfRxPkts Counter32, ospf3IntfTxPkts Counter32, ospf3IntfDisdPkts Counter32, ospf3IntfRxHello Counter32, ospf3IntfTxHello Counter32, ospf3IntfDisdHello Counter32, ospf3IntfRxDatabase Counter32, ospf3IntfTxDatabase Counter32, ospf3IntfDisdDatabase Counter32, ospf3IntfRxlsReqs Counter32, ospf3IntfTxlsReqs Counter32, ospf3IntfDisdlsReqs Counter32, ospf3IntfRxlsAcks Counter32, ospf3IntfTxlsAcks Counter32, ospf3IntfDisdlsAcks Counter32, ospf3IntfRxlsUpdates Counter32, ospf3IntfTxlsUpdates Counter32, ospf3IntfDisdlsUpdates Counter32 } ospf3IntfRxTxDisdIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ospf3 Intf for which these statistics apply." ::= { ospf3IntfRxTxDisdStatsEntry 1 } ospf3IntfRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Ospf3 packets received on this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 2 } ospf3IntfTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Ospf3 packets transmitted on this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 3 } ospf3IntfDisdPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Ospf3 packets discaded on this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 4 } ospf3IntfRxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received on this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 5 } ospf3IntfTxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets transmitted on this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 6 } ospf3IntfDisdHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets discaded in this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 7 } ospf3IntfRxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets transmitted for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 8 } ospf3IntfTxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets transmitted for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 9 } ospf3IntfDisdDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets discarded for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 10 } ospf3IntfRxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets received for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 11 } ospf3IntfTxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets transmitted for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 12 } ospf3IntfDisdlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets discarded for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 13 } ospf3IntfRxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets received for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 14 } ospf3IntfTxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets transmitted for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 15 } ospf3IntfDisdlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets discarded for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 16 } ospf3IntfRxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets received for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 17 } ospf3IntfTxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets transmitted for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 18 } ospf3IntfDisdlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets discarded for this Ospf3 interface." ::= { ospf3IntfRxTxDisdStatsEntry 19 } ospf3IntfNbrChangeStats OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3IntfNbrChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Ospf3 Interface Neighbour change Statistics." ::= { ospf3Interface 2 } ospf3IntfNbrChangeStatsEntry OBJECT-TYPE SYNTAX Ospf3IntfNbrChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ospf3 interface Neighbour Change statistics." INDEX { ospf3IntfNbrIndex } ::= { ospf3IntfNbrChangeStats 1 } Ospf3IntfNbrChangeStatsEntry ::= SEQUENCE { ospf3IntfNbrIndex Integer32, ospf3IntfNbrDown Counter32, ospf3IntfNbrAttempt Counter32, ospf3IntfNbrInit Counter32, ospf3IntfNbrN2way Counter32, ospf3IntfNbrExStart Counter32, ospf3IntfNbrExchange Counter32, ospf3IntfNbrLoading Counter32, ospf3IntfNbrFull Counter32, ospf3IntfNbrAllEvents Counter32 } ospf3IntfNbrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the Ospf3 Interface for which these statistics apply." ::= { ospf3IntfNbrChangeStatsEntry 1 } ospf3IntfNbrDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this interface have changed into DOWN state." ::= { ospf3IntfNbrChangeStatsEntry 2 } ospf3IntfNbrAttempt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this interface have changed into ATTEMPT state." ::= { ospf3IntfNbrChangeStatsEntry 3 } ospf3IntfNbrInit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this interface have changed into INIT state." ::= { ospf3IntfNbrChangeStatsEntry 4 } ospf3IntfNbrN2way OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this interface have changed into 2WAY state." ::= { ospf3IntfNbrChangeStatsEntry 5 } ospf3IntfNbrExStart OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this interface have changed into EXSTART state." ::= { ospf3IntfNbrChangeStatsEntry 6 } ospf3IntfNbrExchange OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this interface have changed into EXCHANGE state." ::= { ospf3IntfNbrChangeStatsEntry 7 } ospf3IntfNbrLoading OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this interface have changed into LOADING state." ::= { ospf3IntfNbrChangeStatsEntry 8 } ospf3IntfNbrFull OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this interface have changed into FULL state." ::= { ospf3IntfNbrChangeStatsEntry 9 } ospf3IntfNbrAllEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on this interface have changed state or an error had occured." ::= { ospf3IntfNbrChangeStatsEntry 10 } ospf3IntfChangeStats OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3IntfChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Ospf3 Interface change Statistics." ::= { ospf3Interface 3 } ospf3IntfChangeStatsEntry OBJECT-TYPE SYNTAX Ospf3IntfChangeStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ospf3 interface Change statistics." INDEX { ospf3IntfIndex } ::= { ospf3IntfChangeStats 1 } Ospf3IntfChangeStatsEntry ::= SEQUENCE { ospf3IntfIndex Integer32, ospf3IntfDown Counter32, ospf3IntfLoop Counter32, ospf3IntfWaiting Counter32, ospf3IntfPtop Counter32, ospf3IntfDr Counter32, ospf3IntfBackup Counter32, ospf3IntfDrOther Counter32, ospf3IntfAllEvents Counter32 } ospf3IntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the Ospf3 Interface for which these statistics apply." ::= { ospf3IntfChangeStatsEntry 1 } ospf3IntfDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times the interface was down." ::= { ospf3IntfChangeStatsEntry 2 } ospf3IntfLoop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times this interface changed State into the LOOP State." ::= { ospf3IntfChangeStatsEntry 3 } ospf3IntfWaiting OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times this interface changed State into the Waiting State." ::= { ospf3IntfChangeStatsEntry 4 } ospf3IntfPtop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times this interface changed State into the PTOP State." ::= { ospf3IntfChangeStatsEntry 5 } ospf3IntfDr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times this interface changed State into the DR State." ::= { ospf3IntfChangeStatsEntry 6 } ospf3IntfBackup OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times this interface changed State into the Backup State." ::= { ospf3IntfChangeStatsEntry 7 } ospf3IntfDrOther OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times this interface changed State into the DrOther State." ::= { ospf3IntfChangeStatsEntry 8 } ospf3IntfAllEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times this interface changed State." ::= { ospf3IntfChangeStatsEntry 9 } ospf3IntfErrorStats OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3IntfErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Ospf3 Interface Error Statistics." ::= { ospf3Interface 4 } ospf3IntfErrorStatsEntry OBJECT-TYPE SYNTAX Ospf3IntfErrorStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Error Statistics for an Ospf3 interface." INDEX { ospf3IntfErrIndex } ::= { ospf3IntfErrorStats 1 } Ospf3IntfErrorStatsEntry ::= SEQUENCE { ospf3IntfErrIndex Integer32, ospf3IntfErrRxOnPasv Counter32, ospf3IntfErrRxOspfOff Counter32, ospf3IntfErrRxOnNotup Counter32, ospf3IntfErrRxVerMismatch Counter32, ospf3IntfErrRxZeroRTRID Counter32, ospf3IntfErrRxSameRTRID Counter32, ospf3IntfErrRxMismatchInstID Counter32, ospf3IntfErrBadAreaID Counter32, ospf3IntfErrBadDestAddr Counter32, ospf3IntfErrBadChecksum Counter32, ospf3IntfErrBadNeighbour Counter32, ospf3IntfErrBadPktType Counter32, ospf3IntfErrHelloMismatch Counter32, ospf3IntfErrOptionsMismatch Counter32, ospf3IntfErrDeadMismatch Counter32, ospf3IntfErrMTUMismatch Counter32, ospf3IntfErrHelloNoNbr Counter32 } ospf3IntfErrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the Ospf3 Intf for which these statistics apply." ::= { ospf3IntfErrorStatsEntry 1 } ospf3IntfErrRxOnPasv OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by this interface that are received on a passive interface." ::= { ospf3IntfErrorStatsEntry 2 } ospf3IntfErrRxOspfOff OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by this interface that are received while OSPF was disabled." ::= { ospf3IntfErrorStatsEntry 3 } ospf3IntfErrRxOnNotup OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by this interface that are received while the interface was disabled." ::= { ospf3IntfErrorStatsEntry 4 } ospf3IntfErrRxVerMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by this interface that have an OSPF version number not equal to the one of the interface." ::= { ospf3IntfErrorStatsEntry 5 } ospf3IntfErrRxZeroRTRID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by this interface that have a RouterID of 0." ::= { ospf3IntfErrorStatsEntry 6 } ospf3IntfErrRxSameRTRID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by this interface that have the same RouterID as this Router." ::= { ospf3IntfErrorStatsEntry 7 } ospf3IntfErrRxMismatchInstID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by this interface that have an instance number not equal to the one of the interface." ::= { ospf3IntfErrorStatsEntry 8 } ospf3IntfErrBadAreaID OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received by this interface that have an area number not equal to the one of the area of the interface." ::= { ospf3IntfErrorStatsEntry 9 } ospf3IntfErrBadDestAddr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets discarded by this interface because of a destination address mismatch." ::= { ospf3IntfErrorStatsEntry 10 } ospf3IntfErrBadChecksum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets discarded by this interface because of a bad checksum." ::= { ospf3IntfErrorStatsEntry 11 } ospf3IntfErrBadNeighbour OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets discarded by this interface because they could not be associated with any neighbor." ::= { ospf3IntfErrorStatsEntry 12 } ospf3IntfErrBadPktType OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets discarded by this interface because the packet type was not recognized." ::= { ospf3IntfErrorStatsEntry 13 } ospf3IntfErrHelloMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different hello interval by this interface." ::= { ospf3IntfErrorStatsEntry 14 } ospf3IntfErrOptionsMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different options by this interface." ::= { ospf3IntfErrorStatsEntry 15 } ospf3IntfErrDeadMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different dead interval by this interface." ::= { ospf3IntfErrorStatsEntry 16 } ospf3IntfErrMTUMismatch OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received with a different MTU size by this interface." ::= { ospf3IntfErrorStatsEntry 17 } ospf3IntfErrHelloNoNbr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received from an unknown neighbor when this interface has a Network Type of NBMA or PTOMP." ::= { ospf3IntfErrorStatsEntry 18 } -- Ospf3 General Statistics contains the cumulative stats for all -- areas / interfaces ospf3CumRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Ospf3 packets received on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 1 } ospf3CumTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Ospf3 packets transmitted on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 2 } ospf3CumDisdPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Ospf3 packets discaded on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 3 } ospf3CumRxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets received on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 4 } ospf3CumTxHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets transmitted on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 5 } ospf3CumDisdHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Hello packets discaded on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 6 } ospf3CumRxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets received on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 7 } ospf3CumTxDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets transmitted on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 8 } ospf3CumDisdDatabase OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Database Description packets discarded on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 9 } ospf3CumRxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets received on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 10 } ospf3CumTxlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets transmitted on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 11 } ospf3CumDisdlsReqs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Request packets discarded on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 12 } ospf3CumRxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets received on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 13 } ospf3CumTxlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets transmitted on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 14 } ospf3CumDisdlsAcks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Acknowledgement packets discarded on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 15 } ospf3CumRxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets received on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 16 } ospf3CumTxlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets transmitted on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 17 } ospf3CumDisdlsUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link State Update packets discarded on all of the router's interfaces." ::= { ospf3CumRxTxDisdStats 18 } ospf3CumNbrDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing on the interfaces now present on the router have changed into DOWN state." ::= { ospf3CumNbrChangeStats 1 } ospf3CumNbrAttempt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing the on interfaces now present on the router have changed into ATTEMPT state." ::= { ospf3CumNbrChangeStats 2 } ospf3CumNbrInit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing the on interfaces now present on the router have changed into INIT state." ::= { ospf3CumNbrChangeStats 3 } ospf3CumNbrN2way OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing the on interfaces now present on the router have changed into 2WAY state." ::= { ospf3CumNbrChangeStats 4 } ospf3CumNbrExStart OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing the on interfaces now present on the router have changed into EXSTART state." ::= { ospf3CumNbrChangeStats 5 } ospf3CumNbrExchange OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing the on interfaces now present on the router have changed into EXCHANGE state." ::= { ospf3CumNbrChangeStats 6 } ospf3CumNbrLoading OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing the on interfaces now present on the router have changed into LOADING state." ::= { ospf3CumNbrChangeStats 7 } ospf3CumNbrFull OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing the on interfaces now present on the router have changed into FULL state." ::= { ospf3CumNbrChangeStats 8 } ospf3CumNbrAllEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times neighbors now existing the on interfaces now present on the router have changed state." ::= { ospf3CumNbrChangeStats 9 } ospf3CumIntfDown OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times, for all the interfaces on the router, an interface was down." ::= { ospf3CumIntfChangeStats 1 } ospf3CumIntfLoop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times , for all the interfaces on the router, an interface changed State into the LOOP State." ::= { ospf3CumIntfChangeStats 2 } ospf3CumIntfWaiting OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times , for all the interfaces on the router, an interface changed State into the WAITING State." ::= { ospf3CumIntfChangeStats 3 } ospf3CumIntfPtop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times , for all the interfaces on the router, an interface changed State into the PTOP State." ::= { ospf3CumIntfChangeStats 4 } ospf3CumIntfDr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times , for all the interfaces on the router, an interface changed State into the DR State." ::= { ospf3CumIntfChangeStats 5 } ospf3CumIntfBackup OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times , for all the interfaces on the router, an interface changed State into the BACKUP State." ::= { ospf3CumIntfChangeStats 6 } ospf3CumIntfDrOther OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times , for all the interfaces on the router, an interface changed State into the DROTHER State." ::= { ospf3CumIntfChangeStats 7 } ospf3CumIntfAllEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of times , for all the interfaces on the router, an interface changed it's state." ::= { ospf3CumIntfChangeStats 8 } ospf3TmrsKckOffHello OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the Hello timer has been fired (which triggers the send of a Hello packet) across all OPSF areas and interfaces." ::= { ospf3TimersKickOffStats 1 } ospf3TmrsKckOffWait OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the KickOffWait timer has been fired (which triggers the send of a KickOffWait packet) across all OPSF areas and interfaces." ::= { ospf3TimersKickOffStats 2 } ospf3TmrsKckOffPoll OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the KickOffPoll timer has been fired (which triggers the send of a KickOffPoll packet) across all OPSF areas and interfaces." ::= { ospf3TimersKickOffStats 3 } ospf3TmrsKckOffNbrProbe OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sum total number of times the KickOffNbrProbe timer has been fired (which triggers the send of a KickOffNbrProbe packet) across all OPSF areas and interfaces." ::= { ospf3TimersKickOffStats 4 } mldIfStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF MldIfStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table listing the interfaces on which MLD is enabled." ::= { mldStats 1 } mldIfStatsEntry OBJECT-TYPE SYNTAX MldIfStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry representing an interface stats on which MLD is enabled." INDEX { mldIfStatsIfIndex } ::= { mldIfStatsTable 1 } MldIfStatsEntry ::= SEQUENCE { mldIfStatsIfIndex Integer32, rxMldIfStatsGeneralQuery Counter32, rxMldIfStatsMASQuery Counter32, rxMldIfStatsMASSQQuery Counter32, rxMldIfStatsMLDv1Report Counter32, rxMldIfStatsMLDv1Done Counter32, rxMldIfStatsMLDv2Report Counter32, rxMldIfStatsIncCrsv2 Counter32, rxMldIfStatsExcCrsv2 Counter32, rxMldIfStatsToIncFmcrsv2 Counter32, rxMldIfStatsToExcFmcrsv2 Counter32, rxMldIfStatsAllowSlcrsv2 Counter32, rxMldIfStatsBlockSlcrsv2 Counter32, txMldIfStatsGeneralQuery Counter32, txMldIfStatsMASQuery Counter32, txMldIfStatsMASSQQuery Counter32, txMldIfStatsMLDv1Report Counter32, txMldIfStatsMLDv1Done Counter32, txMldIfStatsMLDv2Report Counter32, txMldIfStatsIncCrsv2 Counter32, txMldIfStatsExcCrsv2 Counter32, txMldIfStatsToIncFmcrsv2 Counter32, txMldIfStatsToExcFmcrsv2 Counter32, txMldIfStatsAllowSlcrsv2 Counter32, txMldIfStatsBlockSlcrsv2 Counter32, errMldIfStatsGeneralQuery Counter32, errMldIfStatsMASQuery Counter32, errMldIfStatsMASSQQuery Counter32, errMldIfStatsMLDv1Report Counter32, errMldIfStatsMLDv1Done Counter32, errMldIfStatsMLDv2Report Counter32, errMldIfStatsIncCrsv2 Counter32, errMldIfStatsExcCrsv2 Counter32, errMldIfStatsToIncFmcrsv2 Counter32, errMldIfStatsToExcFmcrsv2 Counter32, errMldIfStatsAllowSlcrsv2 Counter32, errMldIfStatsBlockSlcrsv2 Counter32 } mldIfStatsIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The internetwork-layer interface value of the interface for which MLD msg stats is counted." ::= { mldIfStatsEntry 1 } rxMldIfStatsGeneralQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Queries received." ::= { mldIfStatsEntry 2 } rxMldIfStatsMASQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener MAS Queries received." ::= { mldIfStatsEntry 3 } rxMldIfStatsMASSQQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener MASSQ Queries received." ::= { mldIfStatsEntry 4 } rxMldIfStatsMLDv1Report OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Reports (v1) received." ::= { mldIfStatsEntry 5 } rxMldIfStatsMLDv1Done OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Dones (v1/v2) received." ::= { mldIfStatsEntry 6 } rxMldIfStatsMLDv2Report OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Reports (v2) received." ::= { mldIfStatsEntry 7 } rxMldIfStatsIncCrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD INC CRs (v2) received." ::= { mldIfStatsEntry 8 } rxMldIfStatsExcCrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD EXC CRs (v2) received." ::= { mldIfStatsEntry 9 } rxMldIfStatsToIncFmcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD TO_INC FMCRs (v2) received." ::= { mldIfStatsEntry 10 } rxMldIfStatsToExcFmcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD TO_EXC FMCRs (v2) received." ::= { mldIfStatsEntry 11 } rxMldIfStatsAllowSlcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD ALLOW SLCRs (v2) received." ::= { mldIfStatsEntry 12 } rxMldIfStatsBlockSlcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD BLOCK SLCRs (v2) received." ::= { mldIfStatsEntry 13 } txMldIfStatsGeneralQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Queries sent." ::= { mldIfStatsEntry 14 } txMldIfStatsMASQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener MAS Queries sent." ::= { mldIfStatsEntry 15 } txMldIfStatsMASSQQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener MASSQ Queries sent." ::= { mldIfStatsEntry 16 } txMldIfStatsMLDv1Report OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Reports (v1) sent." ::= { mldIfStatsEntry 17 } txMldIfStatsMLDv1Done OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Dones (v1/v2) sent." ::= { mldIfStatsEntry 18 } txMldIfStatsMLDv2Report OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Reports (v2) sent." ::= { mldIfStatsEntry 19 } txMldIfStatsIncCrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD INC CRs (v2) sent" ::= { mldIfStatsEntry 20 } txMldIfStatsExcCrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD EXC CRs (v2) sent" ::= { mldIfStatsEntry 21 } txMldIfStatsToIncFmcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD TO_INC FMCRs (v2) sent" ::= { mldIfStatsEntry 22 } txMldIfStatsToExcFmcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD TO_EXC FMCRs (v2) sent" ::= { mldIfStatsEntry 23 } txMldIfStatsAllowSlcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD ALLOW SLCRs (v2) sent" ::= { mldIfStatsEntry 24 } txMldIfStatsBlockSlcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD BLOCK SLCRs (v2) received." ::= { mldIfStatsEntry 25 } errMldIfStatsGeneralQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Queries errors." ::= { mldIfStatsEntry 27 } errMldIfStatsMASQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener MAS Queries errors." ::= { mldIfStatsEntry 28 } errMldIfStatsMASSQQuery OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener MASSQ Queries errors." ::= { mldIfStatsEntry 29 } errMldIfStatsMLDv1Report OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Report (v1) errors." ::= { mldIfStatsEntry 30 } errMldIfStatsMLDv1Done OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Done (v1/v2) errors." ::= { mldIfStatsEntry 31 } errMldIfStatsMLDv2Report OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Listener Report (v2) errors." ::= { mldIfStatsEntry 32} errMldIfStatsIncCrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD INC CRs (v2) errors." ::= { mldIfStatsEntry 33 } errMldIfStatsExcCrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD EXC CRs (v2) errors." ::= { mldIfStatsEntry 34 } errMldIfStatsToIncFmcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD TO_INC FMCRs (v2) errors." ::= { mldIfStatsEntry 35 } errMldIfStatsToExcFmcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD TO_EXC FMCRs (v2) errors." ::= { mldIfStatsEntry 36 } errMldIfStatsAllowSlcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD ALLOW SLCRs (v2) errors." ::= { mldIfStatsEntry 37 } errMldIfStatsBlockSlcrsv2 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD BLOCK SLCRs (v2) errors." ::= { mldIfStatsEntry 38 } mldStatBadLength OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of bad length mld packet." ::= { mldStats 2 } mldStatBadChecksum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of bad checksum mld packet." ::= { mldStats 3 } mldStatBadReceiveIf OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of bad reveive if mld packet." ::= { mldStats 4 } mldStatReceiveNonLocal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of non local received mld packet." ::= { mldStats 5 } mldStatInvalidPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of invalid packets." ::= { mldStats 6 } mldStatTotalL3Ipv6SgvEntries OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total L3 IPv6 (S, G, V) entries" ::= { mldStats 7 } mldStatTotalMLDGroups OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of MLD Groups." ::= { mldStats 8 } mldStatClearAll OBJECT-TYPE SYNTAX INTEGER { other(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear all MLD stats. Returns other(1) when read." ::= { mldStats 9 } -- Information - Run-time IP Route Table ipInfoRouterID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Router ID information." ::= { ipInfo 1 } ipIntfInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IntfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP interface information." ::= {ipIntfInfo 1 } intfInfoEntry OBJECT-TYPE SYNTAX IntfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in IP interface information table." INDEX { intfInfoIndex } ::= { ipIntfInfoTable 1 } IntfInfoEntry ::= SEQUENCE { intfInfoIndex Integer32, intfInfoAddr DisplayString, intfInfoNetMask DisplayString, intfInfoBcastAddr DisplayString, intfInfoVlan Integer32, intfInfoStatus INTEGER } intfInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number for which the information is related." ::= { intfInfoEntry 1} intfInfoAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the interface." ::= { intfInfoEntry 3 } intfInfoNetMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The subnet mask of the interface." ::= { intfInfoEntry 4 } intfInfoBcastAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The broadcast address of the interface." ::= { intfInfoEntry 5 } intfInfoVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN number for this interface." ::= { intfInfoEntry 6 } intfInfoStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the interface." ::= { intfInfoEntry 7 } ipIntfLoopbackInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IntfLoopbackInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IP Loopback interface information." ::= {ipIntfLoopbackInfo 1 } intfLoopbackInfoEntry OBJECT-TYPE SYNTAX IntfLoopbackInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in IP Loopback interface information table." INDEX { intfLoopbackInfoIndex } ::= { ipIntfLoopbackInfoTable 1 } IntfLoopbackInfoEntry ::= SEQUENCE { intfLoopbackInfoIndex Integer32, intfLoopbackInfoAddr DisplayString, intfLoopbackInfoNetMask DisplayString, intfLoopbackInfoBcastAddr DisplayString, intfLoopbackInfoStatus INTEGER } intfLoopbackInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Loopback interface number for which the information is related." ::= { intfLoopbackInfoEntry 1} intfLoopbackInfoAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the interface." ::= { intfLoopbackInfoEntry 3 } intfLoopbackInfoNetMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The subnet mask of the interface." ::= { intfLoopbackInfoEntry 4 } intfLoopbackInfoBcastAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The broadcast address of the interface." ::= { intfLoopbackInfoEntry 5 } intfLoopbackInfoStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the interface." ::= { intfLoopbackInfoEntry 7 } ipRouteInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IpRouteInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of run-time IP routes." ::= { ipRoutingInfo 1 } ipRouteInfoEntry OBJECT-TYPE SYNTAX IpRouteInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the run-time IP route table" INDEX { ipRouteInfoIndx } ::= { ipRouteInfoTable 1 } IpRouteInfoEntry ::= SEQUENCE { ipRouteInfoIndx Integer32, ipRouteInfoDestIp IpAddress, ipRouteInfoMask IpAddress, ipRouteInfoGateway IpAddress, ipRouteInfoTag INTEGER, ipRouteInfoType INTEGER, ipRouteInfoInterface Integer32, ipRouteInfoGateway1 IpAddress, ipRouteInfoGateway2 IpAddress, ipRouteInfoMetric Integer32 } ipRouteInfoIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of this route table." ::= { ipRouteInfoEntry 1 } ipRouteInfoDestIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address of this route." ::= { ipRouteInfoEntry 2 } ipRouteInfoMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP mask of this route." ::= { ipRouteInfoEntry 3 } ipRouteInfoGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The next-hop router address for this route." ::= { ipRouteInfoEntry 4 } ipRouteInfoTag OBJECT-TYPE SYNTAX INTEGER { fixed(1), static(2), addr(3), rip(4), broadcast(5), martian(6), multicast(7), vip(8), bgp(9), ospf(10), none(11) } MAX-ACCESS read-only STATUS current DESCRIPTION "The tag-type for this route." ::= { ipRouteInfoEntry 5 } ipRouteInfoType OBJECT-TYPE SYNTAX INTEGER { indirect(1), direct(2), local(3), broadcast(4), martian(5), multicast(6), other(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the route." ::= { ipRouteInfoEntry 6 } ipRouteInfoInterface OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number for which the destination address is applicable." ::= { ipRouteInfoEntry 7 } ipRouteInfoGateway1 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The next-hop router address for this route." ::= { ipRouteInfoEntry 8 } ipRouteInfoGateway2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The next-hop router address for this route." ::= { ipRouteInfoEntry 9 } ipRouteInfoMetric OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Metric for this route." ::= { ipRouteInfoEntry 10 } routeTableClear OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the route table." ::= { ipRoutingInfo 2 } ipRouteEcmpInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IpRouteEcmpInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of run-time IP routes." ::= { ipEcmpRoutingInfo 1 } ipRouteEcmpInfoEntry OBJECT-TYPE SYNTAX IpRouteEcmpInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the run-time IP route table" INDEX { ipRouteEcmpInfoDestIndx, ipRouteEcmpInfoGwIndx } ::= { ipRouteEcmpInfoTable 1 } IpRouteEcmpInfoEntry ::= SEQUENCE { ipRouteEcmpInfoDestIndx Integer32, ipRouteEcmpInfoGwIndx Integer32, ipRouteEcmpInfoDest IpAddress, ipRouteEcmpInfoMask IpAddress, ipRouteEcmpInfoGateway IpAddress, ipRouteEcmpInfoInterface Integer32, ipRouteEcmpInfoGwStatus INTEGER } ipRouteEcmpInfoDestIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of unique destinations IP." ::= { ipRouteEcmpInfoEntry 1 } ipRouteEcmpInfoGwIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the gateway per destination." ::= { ipRouteEcmpInfoEntry 2 } ipRouteEcmpInfoDest OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP of this route." ::= { ipRouteEcmpInfoEntry 3 } ipRouteEcmpInfoMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP mask of this route." ::= { ipRouteEcmpInfoEntry 4 } ipRouteEcmpInfoGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The next-hop router address for this route." ::= { ipRouteEcmpInfoEntry 5 } ipRouteEcmpInfoInterface OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface for the next-hop." ::= { ipRouteEcmpInfoEntry 6 } ipRouteEcmpInfoGwStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Up/Down status of the gateway" ::= { ipRouteEcmpInfoEntry 7 } ipEcmpHashSIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The SIP Address." ::= { ipEcmpHash 1 } ipEcmpHashDIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The DIP Address (enter 0 for SIP only)." ::= { ipEcmpHash 2 } ipEcmpHashNumberPaths OBJECT-TYPE SYNTAX INTEGER (2..5) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of ECMP paths." ::= { ipEcmpHash 3 } ipEcmpHashRouteNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The result of the hash algorithm. For this to work the values for ipEcmpHashSIPAddr, ipEcmpHashDIPAddr, ipEcmpHashNumberPaths must be set. If the result is 0 ipEcmpHashNumberPaths is not correctly set." ::= { ipEcmpHash 4 } mldInfoGroupsTable OBJECT-TYPE SYNTAX SEQUENCE OF MldInfoGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table listing the IPv6 multicast groups for which there are members on a particular interface." ::= { mldInfo 1 } mldInfoGroupEntry OBJECT-TYPE SYNTAX MldInfoGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the mldInfoGroupsTable" INDEX { mldInfoGroupId } ::= { mldInfoGroupsTable 1 } MldInfoGroupEntry ::= SEQUENCE { mldInfoGroupIfIndex Integer32, mldInfoGroupAddress InetAddressIPv6, mldInfoGroupPortNumber Integer32, mldInfoGroupVlanID Integer32, mldInfoGroupLastReporter InetAddressIPv6, mldInfoGroupSource InetAddressIPv6, mldInfoGroupFilterType DisplayString, mldInfoGroupExpiryTime DisplayString, mldInfoGroupVersion Integer32, mldInfoGroupFwd Integer32, mldInfoGroupId Integer32 } mldInfoGroupIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The internetwork-layer interface for which this entry contains information for an IPv6 multicast group address." ::= { mldInfoGroupEntry 1 } mldInfoGroupAddress OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 multicast group address for which this entry contains information. Its address MUST be of format: 2x:2x:2x:2x:2x:2x:2x:2x" ::= { mldInfoGroupEntry 2 } mldInfoGroupPortNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number for which this entry contains information for an IPv6 multicast group address." ::= { mldInfoGroupEntry 3 } mldInfoGroupVlanID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID for which this entry contains information for an IPv6 multicast group address." ::= { mldInfoGroupEntry 4 } mldInfoGroupLastReporter OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 address of the source of the last membership report received for this IPv6 Multicast group address on this interface. If no membership report has been received, this object has the value 00:0:00:00:00:00:00:00. Its address MUST be of format:2x:2x:2x:2x:2x:2x:2x:2x" ::= { mldInfoGroupEntry 5 } mldInfoGroupSource OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-only STATUS current DESCRIPTION "ONLY for MLDv2. The IPv6 address for which the this entry's filter is applied. Its address MUST be of format: 2x:2x:2x:2x:2x:2x:2x:2x" ::= { mldInfoGroupEntry 6 } mldInfoGroupFilterType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "ONLY for MLDv2. The filter type for the specified source." ::= { mldInfoGroupEntry 7 } mldInfoGroupExpiryTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum amount of time remaining before this entry will be aged out. A value of 0 indicates that the entry is only present because mldCacheSelf is true and that if the router left the group, this entry would be aged out immediately. Note that some implementations may process Membership Reports from the local system in the same way as reports from other hosts, so a value of 0 is not required." ::= { mldInfoGroupEntry 8 } mldInfoGroupVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The version of this MLD entry." ::= { mldInfoGroupEntry 9 } mldInfoGroupFwd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies if forwarding is enabled for this entry." ::= { mldInfoGroupEntry 10 } mldInfoGroupId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "MLD group index." ::= { mldInfoGroupEntry 11 } mldInfoMRoutersTable OBJECT-TYPE SYNTAX SEQUENCE OF MldInfoMRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table listing the IPv6 multicast routers on an interface." ::= { mldInfo 2 } mldInfoMRouterEntry OBJECT-TYPE SYNTAX MldInfoMRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the mldInfoMRoutersTable" INDEX { mldInfoMRouterId } ::= { mldInfoMRoutersTable 1 } MldInfoMRouterEntry ::= SEQUENCE { mldInfoMRouterIfIndex Integer32, mldInfoMRouterSrcIp InetAddressIPv6, mldInfoMRouterPortNumber Integer32, mldInfoMRouterVlan Integer32, mldInfoMRouterQrv Integer32, mldInfoMRouterQqic Integer32, mldInfoMRouterMaxRespDelay Integer32, mldInfoMRouterVersion Integer32, mldInfoMRouterExpiryTime DisplayString, mldInfoMRouterId Integer32 } mldInfoMRouterIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface on which the multicast router is learnt." ::= { mldInfoMRouterEntry 1 } mldInfoMRouterSrcIp OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast router's ip." ::= { mldInfoMRouterEntry 2 } mldInfoMRouterPortNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port on which the multicast router is learnt." ::= { mldInfoMRouterEntry 3 } mldInfoMRouterVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan in which the multicast router is learnt." ::= { mldInfoMRouterEntry 4 } mldInfoMRouterQrv OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This multicast router's Maximum Response Delay" ::= { mldInfoMRouterEntry 5 } mldInfoMRouterQqic OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "ONLY for MLDv2. This multicast router's QQIC" ::= { mldInfoMRouterEntry 6 } mldInfoMRouterMaxRespDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This multicast router's Maximum Response Delay." ::= { mldInfoMRouterEntry 7 } mldInfoMRouterVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This multicast router's MLD version." ::= { mldInfoMRouterEntry 8 } mldInfoMRouterExpiryTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This multicast router's expiry time." ::= { mldInfoMRouterEntry 9 } mldInfoMRouterId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This multicast router's index." ::= { mldInfoMRouterEntry 10 } mldClearTables OBJECT-TYPE SYNTAX INTEGER { none(0), clearGroups(1), clearMrouters(2), clearAll(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear the MLD tables. When setting clearGroups(1), the dynamic groups are removed, when setting clearMrouters(2), the mrouter tables are removed and when setting clearAll(3), both the dynamic groups and the mrouter tables are removed. When read, none(0) is always returned." ::= { mldInfo 3 } mldInfoInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF MldInfoInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the informatio of interfaces on which MLD is enabled." ::= { mldInfo 4 } mldInfoInterfaceEntry OBJECT-TYPE SYNTAX MldInfoInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing the information of an interface on which MLD is enabled." INDEX { mldInfoInterfaceIfIndex } ::= { mldInfoInterfaceTable 1 } MldInfoInterfaceEntry ::= SEQUENCE { mldInfoInterfaceIfIndex Integer32, mldInfoInterfaceState INTEGER, mldInfoInterfaceVersion INTEGER, mldInfoInterfaceQuerierStatus INTEGER, mldInfoInterfaceQuerier InetAddressIPv6, mldInfoInterfaceQuerierExpiryTime DisplayString, mldInfoInterfaceQuerierPort Integer32, mldInfoInterfaceGroups INTEGER } mldInfoInterfaceIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The internetwork-layer interface value of the interface for which MLD is enabled." ::= { mldInfoInterfaceEntry 1 } mldInfoInterfaceState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The internetwork-layer interface value of the interface for which MLD is enabled." ::= { mldInfoInterfaceEntry 2 } mldInfoInterfaceVersion OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The version of MLD which is running on this interface. This object is a place holder to allow for new versions of MLD to be introduced. Version 1 of MLD is defined in RFC 2710." DEFVAL { 1 } ::= { mldInfoInterfaceEntry 3 } mldInfoInterfaceQuerierStatus OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies if the switch is Querier or not" ::= { mldInfoInterfaceEntry 4 } mldInfoInterfaceQuerier OBJECT-TYPE SYNTAX InetAddressIPv6 MAX-ACCESS read-only STATUS current DESCRIPTION "The address of the MLD Querier on the IPv6 subnet to which this interface is attached. Its address MUST be of format:2x:2x:2x:2x:2x:2x:2x:2x" ::= { mldInfoInterfaceEntry 5 } mldInfoInterfaceQuerierExpiryTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining before the Other Querier Present Timer expires. If the local system is the querier, the value of this object is zero." ::= { mldInfoInterfaceEntry 6 } mldInfoInterfaceQuerierPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port on which the Querier is learnt. If the local system is the querier, the value of this object is zero." ::= { mldInfoInterfaceEntry 7 } mldInfoInterfaceGroups OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of entries for this interface in the Cache Table." ::= { mldInfoInterfaceEntry 8 } -- Run Time ARP Table arpInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF AgArpInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of ARP entries." ::= { arpInfo 1 } arpInfoEntry OBJECT-TYPE SYNTAX AgArpInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the ARP table" INDEX { arpInfoDestIp } ::= { arpInfoTable 1 } AgArpInfoEntry ::= SEQUENCE { arpInfoDestIp IpAddress, arpInfoMacAddr PhysAddress, arpInfoVLAN Integer32, arpInfoSrcPort PortNumber, arpInfoFlag INTEGER } arpInfoDestIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address of the ARP entry." ::= { arpInfoEntry 1 } arpInfoMacAddr OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address for the ARP entry." ::= { arpInfoEntry 2 } arpInfoVLAN OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN identifier for the ARP entry." ::= { arpInfoEntry 3 } arpInfoSrcPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The port number on which this entry's equivalence is effective." ::= { arpInfoEntry 4 } arpInfoFlag OBJECT-TYPE SYNTAX INTEGER { clear(1), unresolved(2), permanent(3), indirect(4), layer4(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The flag associated with this ARP entry." ::= { arpInfoEntry 6 } arpCacheClear OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the ARP cache." ::= { arpInfo 2 } -- VRRP Information vrrpInfoVirtRtrTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpInfoVirtRtrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VRRP virtual router run-time information." ::= { vrrpInfo 1 } vrrpInfoVirtGroupState OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "VRRP group state." ::= { vrrpInfo 2 } vrrpInfoVirtGroupPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VRRP group priority." ::= { vrrpInfo 3 } vrrpInfoVirtRtrTableEntry OBJECT-TYPE SYNTAX VrrpInfoVirtRtrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The run-time information about a VRRP virtual router." INDEX { vrrpInfoVirtRtrIndex } ::= { vrrpInfoVirtRtrTable 1 } VrrpInfoVirtRtrTableEntry ::= SEQUENCE { vrrpInfoVirtRtrIndex Integer32, vrrpInfoVirtRtrState INTEGER, vrrpInfoVirtRtrOwnership INTEGER, vrrpInfoVirtRtrConfig INTEGER, vrrpInfoVirtRtrID INTEGER, vrrpInfoVirtRtrAddr IpAddress, vrrpInfoVirtRtrIfIndex Integer32, vrrpInfoVirtRtrPriority INTEGER } vrrpInfoVirtRtrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router index." ::= { vrrpInfoVirtRtrTableEntry 1 } vrrpInfoVirtRtrState OBJECT-TYPE SYNTAX INTEGER { init(1), master(2), backup(3), holdoff(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router state." ::= { vrrpInfoVirtRtrTableEntry 2 } vrrpInfoVirtRtrOwnership OBJECT-TYPE SYNTAX INTEGER { owner(1), renter(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router ownership status." ::= { vrrpInfoVirtRtrTableEntry 3 } vrrpInfoVirtRtrConfig OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the VRRP virtual router." ::= { vrrpInfoVirtRtrTableEntry 4 } vrrpInfoVirtRtrID OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router identifier." ::= { vrrpInfoVirtRtrTableEntry 5 } vrrpInfoVirtRtrAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The VRRP virtual router IP address." ::= { vrrpInfoVirtRtrTableEntry 6 } vrrpInfoVirtRtrIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The IfIndex that the VRRP virtual router is representing." ::= { vrrpInfoVirtRtrTableEntry 7 } vrrpInfoVirtRtrPriority OBJECT-TYPE SYNTAX INTEGER (1..254) MAX-ACCESS read-only STATUS current DESCRIPTION "The priority value to be used by the specified VRRP virtual routers." ::= { vrrpInfoVirtRtrTableEntry 8 } -- Ospf Information ospfGeneralInfo OBJECT IDENTIFIER ::= { ospfinfo 1 } ospfStartTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time when ospf has been started." ::= { ospfGeneralInfo 1 } ospfProcessUptime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time since ospf has been started." ::= { ospfGeneralInfo 2 } ospfLsTypesSupported OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State Types that are supported." ::= { ospfGeneralInfo 3 } ospfIntfCountForRouter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of interfaces for this router." ::= { ospfGeneralInfo 4 } ospfVlinkCountForRouter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of virtual links for this router." ::= { ospfGeneralInfo 5 } ospfTotalNeighbours OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of OSPF neighbours." ::= { ospfGeneralInfo 6 } ospfNbrInInitState OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of neighbours in the initial state of exchange." ::= { ospfGeneralInfo 7 } ospfNbrInExchState OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of neighbours in the exchange state." ::= { ospfGeneralInfo 8 } ospfNbrInFullState OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of neighbours in the Full state of exchange." ::= { ospfGeneralInfo 9 } ospfTotalAreas OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Total number of areas." ::= { ospfGeneralInfo 10 } ospfTotalTransitAreas OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Total number of Transit areas." ::= { ospfGeneralInfo 11 } ospfTotalNssaAreas OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Total number of NSSA areas." ::= { ospfGeneralInfo 12 } ospfTotalStubAreas OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Total number of STUB areas." ::= { ospfGeneralInfo 13 } ospfAreaInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfAreaInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Area information." ::= { ospfinfo 2 } ospfAreaInfoEntry OBJECT-TYPE SYNTAX OspfAreaInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPF area." INDEX { ospfAreaInfoIndex } ::= { ospfAreaInfoTable 1 } OspfAreaInfoEntry ::= SEQUENCE { ospfAreaInfoIndex Integer32, ospfAreaInfoId IpAddress, ospfTotalNumberOfInterfaces Integer32, ospfNumberOfInterfacesUp Integer32, ospfNumberOfLsdbEntries Integer32, ospfAreaInfoAuthType INTEGER, ospfAreaInfoLsTypesAccepted DisplayString, ospfAreaInfoSPF Integer32, ospfAreaInfoAreaBorderRouter Integer32, ospfAreaInfoASBoundaryRouter Integer32, ospfAreaInfoTotalNeighbours Integer32, ospfAreaInfoNeighborsINITstate Integer32, ospfAreaInfoNeighborsEXCHstate Integer32, ospfAreaInfoNeighborsFULLstate Integer32 } ospfAreaInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF area number for which the OSPF info table is related." ::= { ospfAreaInfoEntry 1} ospfAreaInfoId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the OSPF area." ::= { ospfAreaInfoEntry 2 } ospfTotalNumberOfInterfaces OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of interfaces for this OSPF area." ::= { ospfAreaInfoEntry 3 } ospfNumberOfInterfacesUp OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of interfaces UP in area." ::= { ospfAreaInfoEntry 4 } ospfNumberOfLsdbEntries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Link State Database entries for this OSPF area." ::= { ospfAreaInfoEntry 5 } ospfAreaInfoAuthType OBJECT-TYPE SYNTAX INTEGER { none(1), password(2), md5(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Area authentication." ::= { ospfAreaInfoEntry 6 } ospfAreaInfoLsTypesAccepted OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "LS types accepted by this area." ::= { ospfAreaInfoEntry 7 } ospfAreaInfoSPF OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times SPF algorithm has been executed." ::= { ospfAreaInfoEntry 8 } ospfAreaInfoAreaBorderRouter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of ABR local to this area." ::= { ospfAreaInfoEntry 9 } ospfAreaInfoASBoundaryRouter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of ASBR local to this area." ::= { ospfAreaInfoEntry 10 } ospfAreaInfoTotalNeighbours OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of OSPF neighbors." ::= { ospfAreaInfoEntry 11 } ospfAreaInfoNeighborsINITstate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total neighbors in INIT state." ::= { ospfAreaInfoEntry 12 } ospfAreaInfoNeighborsEXCHstate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total neighbors in EXCH state." ::= { ospfAreaInfoEntry 13 } ospfAreaInfoNeighborsFULLstate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total neighbors in FULL state." ::= { ospfAreaInfoEntry 14 } ospfIntfInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfIntfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Interface information." ::= { ospfinfo 3 } ospfIntfInfoEntry OBJECT-TYPE SYNTAX OspfIntfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPF interface." INDEX { ospfIfInfoIndex } ::= { ospfIntfInfoTable 1 } OspfIntfInfoEntry ::= SEQUENCE { ospfIfInfoIndex Integer32, ospfIfInfoIpAddress IpAddress, ospfIfInfoArea INTEGER, ospfIfInfoAdminStatus INTEGER, ospfIfInfoPassive INTEGER, ospfIfInfoPtop INTEGER, ospfIfInfoRouterIP IpAddress, ospfIfInfoState INTEGER, ospfIfInfoPriority INTEGER, ospfIfInfoDesignatedRouterIP IpAddress, ospfIfInfoDesignatedRouterIpAddress IpAddress, ospfIfInfoBackupDesignatedRouterIP IpAddress, ospfIfInfoBackupDesignatedRouterIpAddress IpAddress, ospfIfInfoHello INTEGER, ospfIfInfoHelloMS INTEGER, ospfIfInfoDead INTEGER, ospfIfInfoDeadMS INTEGER, ospfIfInfoWaitInterval Integer32, ospfIfInfoWaitIntervalMS INTEGER, ospfIfInfoRetransmit INTEGER, ospfIfInfoTransitDelay INTEGER, ospfIfInfoTotalNeighbours Integer32, ospfIfInfoEvents Integer32, ospfIfInfoAuthType INTEGER } ospfIfInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF interface number for which the OSPF info table is related." ::= { ospfIntfInfoEntry 1} ospfIfInfoIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the OSPF interface." ::= { ospfIntfInfoEntry 2 } ospfIfInfoArea OBJECT-TYPE SYNTAX INTEGER (0..2) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the area that the interface belongs." ::= { ospfIntfInfoEntry 3 } ospfIfInfoAdminStatus OBJECT-TYPE SYNTAX INTEGER { down(0), up(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Admin Status of the interface: down(0), up(1)." ::= { ospfIntfInfoEntry 4 } ospfIfInfoPassive OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Passive status of the interface: disabled(0), enabled(1)." ::= { ospfIntfInfoEntry 5 } ospfIfInfoPtop OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Point-to-point status of the interface: disabled(0), enabled(1)." ::= { ospfIntfInfoEntry 24 } ospfIfInfoRouterIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The router ID of the switch." ::= { ospfIntfInfoEntry 6 } ospfIfInfoState OBJECT-TYPE SYNTAX INTEGER { down(0), loopback(1), waiting(2), ptop(3), dr(4), backupdr(5), drother(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the interface: Down(0), Loopback(1), Waiting(2), P to P(3), DR(4), BackuDR(5), DR Other(6)." ::= { ospfIntfInfoEntry 7 } ospfIfInfoPriority OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface router priority" ::= { ospfIntfInfoEntry 8 } ospfIfInfoDesignatedRouterIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Designated Router IP (IP Address) for this OSPF interface." ::= { ospfIntfInfoEntry 9 } ospfIfInfoDesignatedRouterIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Designated Router IP Address for this OSPF interface." ::= { ospfIntfInfoEntry 10 } ospfIfInfoBackupDesignatedRouterIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Backup Designated Router IP for this OSPF interface." ::= { ospfIntfInfoEntry 11 } ospfIfInfoBackupDesignatedRouterIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Backup Designated Router Ip Address for this OSPF interface." ::= { ospfIntfInfoEntry 12 } ospfIfInfoHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The hello timer for this OSPF interface." ::= { ospfIntfInfoEntry 13 } ospfIfInfoHelloMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Hello interval seconds(0), milliseconds(1)" ::= { ospfIntfInfoEntry 14 } ospfIfInfoDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The dead timer for this OSPF interface." ::= { ospfIntfInfoEntry 15 } ospfIfInfoDeadMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Dead interval seconds(0), milliseconds(1)" ::= { ospfIntfInfoEntry 16 } ospfIfInfoWaitInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Wait interval for this OSPF interface." ::= { ospfIntfInfoEntry 17 } ospfIfInfoWaitIntervalMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Wait interval seconds(0), milliseconds(1)" ::= { ospfIntfInfoEntry 18 } ospfIfInfoRetransmit OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "The retransmit interval for this OSPF interface." ::= { ospfIntfInfoEntry 19 } ospfIfInfoTransitDelay OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "The transit delay for this OSPF interface." ::= { ospfIntfInfoEntry 20 } ospfIfInfoTotalNeighbours OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Total number of neighbours for this OSPF interface." ::= { ospfIntfInfoEntry 21 } ospfIfInfoEvents OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of events for this OSPF interface." ::= { ospfIntfInfoEntry 22 } ospfIfInfoAuthType OBJECT-TYPE SYNTAX INTEGER { none(1), password(2), md5(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of authentication being used: none(1) - no authentication, password(2) - use password, md5(3) - use MD5 authentication." ::= { ospfIntfInfoEntry 23 } -- OSPF Interface/Virtual Interface Table ospfVirtIntfInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfVirtIntfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF virtual interfaces information." ::= { ospfinfo 4 } ospfVirtIntfInfoEntry OBJECT-TYPE SYNTAX OspfVirtIntfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an OSPF virtual interface." INDEX { ospfVirtIntfInfoIndex } ::= { ospfVirtIntfInfoTable 1 } OspfVirtIntfInfoEntry ::= SEQUENCE { ospfVirtIntfInfoIndex Integer32, ospfVirtIntfInfoIpAddr IpAddress, ospfVirtIntfInfoArea INTEGER, ospfVirtIntfInfoRouterId IpAddress, ospfVirtIntfInfoState INTEGER, ospfVirtIntfInfoCost INTEGER, ospfVirtIntfInfoTrans INTEGER, ospfVirtIntfInfoHello INTEGER, ospfVirtIntfInfoHelloMS INTEGER, ospfVirtIntfInfoDead INTEGER, ospfVirtIntfInfoDeadMS INTEGER, ospfVirtIntfInfoWait INTEGER, ospfVirtIntfInfoWaitMS INTEGER, ospfVirtIntfInfoRetra INTEGER, ospfVirtIntfInfoAuth DisplayString, ospfVirtIntfInfoEvents INTEGER, ospfVirtIntfInfoNbr IpAddress, ospfVirtIntfInfoNbrState INTEGER, ospfVirtIntfInfoAreaId IpAddress } ospfVirtIntfInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Virtual Interface number for which this table is related." ::= { ospfVirtIntfInfoEntry 1 } ospfVirtIntfInfoIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of this virtual interface." ::= { ospfVirtIntfInfoEntry 2 } ospfVirtIntfInfoArea OBJECT-TYPE SYNTAX INTEGER (0..2) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the OSPF area to which this virtual interface belongs." ::= { ospfVirtIntfInfoEntry 3 } ospfVirtIntfInfoRouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID." ::= { ospfVirtIntfInfoEntry 4 } ospfVirtIntfInfoState OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "State disabled(0), enabled(1)" ::= { ospfVirtIntfInfoEntry 5 } ospfVirtIntfInfoCost OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the virtual interface." ::= { ospfVirtIntfInfoEntry 6 } ospfVirtIntfInfoTrans OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The transit delay for the virtual interface." ::= { ospfVirtIntfInfoEntry 7 } ospfVirtIntfInfoHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Hello interval." ::= { ospfVirtIntfInfoEntry 8 } ospfVirtIntfInfoHelloMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Hello interval seconds(0), milliseconds(1)" ::= { ospfVirtIntfInfoEntry 9 } ospfVirtIntfInfoDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Dead interval." ::= { ospfVirtIntfInfoEntry 10 } ospfVirtIntfInfoDeadMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Dead interval seconds(0), milliseconds(1)" ::= { ospfVirtIntfInfoEntry 11 } ospfVirtIntfInfoWait OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Wait interval." ::= { ospfVirtIntfInfoEntry 12 } ospfVirtIntfInfoWaitMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Wait interval seconds(0), milliseconds(1)" ::= { ospfVirtIntfInfoEntry 13 } ospfVirtIntfInfoRetra OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "Retransmit interval." ::= { ospfVirtIntfInfoEntry 14 } ospfVirtIntfInfoAuth OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Authentication." ::= { ospfVirtIntfInfoEntry 15 } ospfVirtIntfInfoEvents OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Events." ::= { ospfVirtIntfInfoEntry 16 } ospfVirtIntfInfoNbr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the OSPF neighbor for this virtual interface." ::= { ospfVirtIntfInfoEntry 17 } ospfVirtIntfInfoNbrState OBJECT-TYPE SYNTAX INTEGER { down(0),attempt(1),init(2),twoway(3), exstart(4),exchange(5),loading(6),full(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "State down(0),attempt(1),init(2),2 way(3), exstart(4),exchange(5),loading(6),full(7)" ::= { ospfVirtIntfInfoEntry 18 } ospfVirtIntfInfoAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The AreaId of the virtual interface." ::= { ospfVirtIntfInfoEntry 19 } -- OSPF Interface/Nbr Info Table ospfIfNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfIfNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Interface Neighbor information." ::= { ospfinfo 5 } ospfIfNbrEntry OBJECT-TYPE SYNTAX OspfIfNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPF interface, neighbor pair." INDEX { ospfIfNbrIntfIndex, ospfIfNbrIpAddr } ::= { ospfIfNbrTable 1 } OspfIfNbrEntry ::= SEQUENCE { ospfIfNbrIntfIndex Integer32, ospfIfNbrIpAddr IpAddress, ospfIfNbrPriority Integer32, ospfIfNbrState INTEGER, ospfIfNbrDesignatedRtr IpAddress, ospfIfNbrBackupDesignatedRtr IpAddress, ospfIfNbrIpAddress IpAddress } ospfIfNbrIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Interface number for which this Interface/Nbr table is related." ::= { ospfIfNbrEntry 1} ospfIfNbrIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Neighbor ID ." ::= { ospfIfNbrEntry 2 } ospfIfNbrPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The priority of the OSPF neighbor." ::= { ospfIfNbrEntry 3 } ospfIfNbrState OBJECT-TYPE SYNTAX INTEGER { down(1), attempt(2), init(3), twoway(4), exStart(5), exchange(6), loading(7), full(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the OSPF neighbor." ::= { ospfIfNbrEntry 4 } ospfIfNbrDesignatedRtr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the Designated Router for this OSPF Neighbor." ::= { ospfIfNbrEntry 5 } ospfIfNbrBackupDesignatedRtr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the backup designated Router for this OSPF Neighbor." ::= { ospfIfNbrEntry 6 } ospfIfNbrIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the OSPF Neighbor." ::= { ospfIfNbrEntry 7 } -- OSPF Interface/Summary Ranges Table ospfSumRangesInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfSumRangesInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF summary ranges information." ::= { ospfinfo 6 } ospfSumRangesInfoEntry OBJECT-TYPE SYNTAX OspfSumRangesInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Summary ranges information." INDEX { ospfSumRangesInfoIndex } ::= { ospfSumRangesInfoTable 1 } OspfSumRangesInfoEntry ::= SEQUENCE { ospfSumRangesInfoIndex Integer32, ospfSumRangesInfoArea INTEGER, ospfSumRangesInfoNetwork IpAddress, ospfSumRangesInfoMask IpAddress, ospfSumRangesInfoAction INTEGER, ospfSumRangesInfoListType INTEGER } ospfSumRangesInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF range index for which this table is related." ::= { ospfSumRangesInfoEntry 1 } ospfSumRangesInfoArea OBJECT-TYPE SYNTAX INTEGER (0..2) MAX-ACCESS read-only STATUS current DESCRIPTION "Area." ::= { ospfSumRangesInfoEntry 2 } ospfSumRangesInfoNetwork OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Network." ::= { ospfSumRangesInfoEntry 3 } ospfSumRangesInfoMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Mask." ::= { ospfSumRangesInfoEntry 4 } ospfSumRangesInfoAction OBJECT-TYPE SYNTAX INTEGER { propagate(0), hide(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Action propagate(0), hide(1)" ::= { ospfSumRangesInfoEntry 5 } ospfSumRangesInfoListType OBJECT-TYPE SYNTAX INTEGER { non-nssa(0), nssa(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Summary address list Non-NSSA(0), NSSA(1)" ::= { ospfSumRangesInfoEntry 6 } -- OSPF Interface/Routes Table ospfRoutesInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfRoutesInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF routes information." ::= { ospfinfo 7 } ospfRoutesInfoEntry OBJECT-TYPE SYNTAX OspfRoutesInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "OSPF routes information." INDEX { ospfRoutesInfoIndex } ::= { ospfRoutesInfoTable 1 } OspfRoutesInfoEntry ::= SEQUENCE { ospfRoutesInfoIndex Integer32, ospfRoutesInfoDestination IpAddress, ospfRoutesInfoMask IpAddress, ospfRoutesInfoVia IpAddress, ospfRoutesInfoType DisplayString } ospfRoutesInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF route table entry index for which this table is related." ::= { ospfRoutesInfoEntry 1 } ospfRoutesInfoDestination OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Destination." ::= { ospfRoutesInfoEntry 2 } ospfRoutesInfoMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Mask." ::= { ospfRoutesInfoEntry 3 } ospfRoutesInfoVia OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Next hop." ::= { ospfRoutesInfoEntry 4 } ospfRoutesInfoType OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Route type. Codes: IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 * - best" ::= { ospfRoutesInfoEntry 5 } -- OSPF Link State Database -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. -- The Area ID, in OSPF, has the same format as an IP Address, -- but has the function of defining a summarization point for -- Link State Advertisements. -- The Router ID, in OSPF, has the same format as an IP Address, -- but identifies the router independent of its IP Address. ospfLsdbInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfLsdbInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Process's Link State Database." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { ospfinfo 8 } ospfLsdbInfoEntry OBJECT-TYPE SYNTAX OspfLsdbInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single Link State Advertisement." INDEX { ospfLsdbInfoIndex } ::= { ospfLsdbInfoTable 1 } OspfLsdbInfoEntry ::= SEQUENCE { ospfLsdbInfoIndex Integer32, ospfLsdbInfoAreaId IpAddress, ospfLsdbInfoType INTEGER, ospfLsdbInfoLsid IpAddress, ospfLsdbInfoRouterId IpAddress, ospfLsdbInfoSequence OCTET STRING, ospfLsdbInfoAge Integer32, ospfLsdbInfoChecksum Integer32, ospfLsdbInfoAdvertisement OCTET STRING } ospfLsdbInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit index in the table." REFERENCE "Private MIBS" ::= { ospfLsdbInfoEntry 1 } ospfLsdbInfoAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit identifier of the Area from which the LSA was received." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfLsdbInfoEntry 2 } -- External Link State Advertisements are permitted -- for backward compatibility, but should be displayed in -- the ospfExtLsdbTable rather than here. ospfLsdbInfoType OBJECT-TYPE SYNTAX INTEGER { routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5), -- but see ospfExtLsdbTable multicastLink (6), nssaExternalLink (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format." REFERENCE "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { ospfLsdbInfoEntry 3 } ospfLsdbInfoLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement." REFERENCE "OSPF Version 2, Section 12.1.4 Link State ID" ::= { ospfLsdbInfoEntry 4 } ospfLsdbInfoRouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { ospfLsdbInfoEntry 5 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. -- Modified to OCTET STRING - for BHM ospfLsdbInfoSequence OBJECT-TYPE SYNTAX OCTET STRING (SIZE(10)) MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement - displayed here in hexazecimal." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { ospfLsdbInfoEntry 6 } ospfLsdbInfoAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { ospfLsdbInfoEntry 7 } ospfLsdbInfoChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { ospfLsdbInfoEntry 8 } ospfLsdbInfoAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE(36)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header. When the LSA is invalid, it is message string 'Invalid LSDB'." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { ospfLsdbInfoEntry 9 } -- SPF Link State Database, External -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. -- This table is identical to the OSPF LSDB Table in -- format, but contains only External Link State -- Advertisements. The purpose is to allow external -- LSAs to be displayed once for the router rather -- than once in each non-stub area. ospfExtLsdbInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfExtLsdbInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Process's Links State Database." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { ospfinfo 9 } ospfExtLsdbInfoEntry OBJECT-TYPE SYNTAX OspfExtLsdbInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single Link State Advertisement." INDEX { ospfExtLsdbInfoIndex } ::= { ospfExtLsdbInfoTable 1 } OspfExtLsdbInfoEntry ::= SEQUENCE { ospfExtLsdbInfoIndex Integer32, ospfExtLsdbInfoType INTEGER, ospfExtLsdbInfoLsid IpAddress, ospfExtLsdbInfoRouterId IpAddress, ospfExtLsdbInfoSequence OCTET STRING, ospfExtLsdbInfoAge Integer32, ospfExtLsdbInfoChecksum Integer32, ospfExtLsdbInfoAdvertisement OCTET STRING } ospfExtLsdbInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit index in the table." REFERENCE "Private MIBS" ::= { ospfExtLsdbInfoEntry 1 } ospfExtLsdbInfoType OBJECT-TYPE SYNTAX INTEGER { asExternalLink (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format." REFERENCE "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { ospfExtLsdbInfoEntry 2 } ospfExtLsdbInfoLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement." REFERENCE "OSPF Version 2, Section 12.1.4 Link State ID" ::= { ospfExtLsdbInfoEntry 3 } ospfExtLsdbInfoRouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { ospfExtLsdbInfoEntry 4 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. -- Modified to OCTET STRING - for BHM ospfExtLsdbInfoSequence OBJECT-TYPE SYNTAX OCTET STRING (SIZE(10)) MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement - displayed here in hexazecimal." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { ospfExtLsdbInfoEntry 5 } ospfExtLsdbInfoAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { ospfExtLsdbInfoEntry 6 } ospfExtLsdbInfoChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { ospfExtLsdbInfoEntry 7 } ospfExtLsdbInfoAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE(36)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { ospfExtLsdbInfoEntry 8 } ospfLoopIfInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfLoopIfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPF Loopback Interface information." ::= { ospfinfo 10 } ospfLoopIfInfoEntry OBJECT-TYPE SYNTAX OspfLoopIfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPF loopback interface." INDEX { ospfLoopIfInfoIndex } ::= { ospfLoopIfInfoTable 1 } OspfLoopIfInfoEntry ::= SEQUENCE { ospfLoopIfInfoIndex Integer32, ospfLoopIfInfoIpAddress IpAddress, ospfLoopIfInfoArea INTEGER, ospfLoopIfInfoAdminStatus INTEGER, ospfLoopIfInfoPassive INTEGER, ospfLoopIfInfoPtop INTEGER, ospfLoopIfInfoRouterIP IpAddress, ospfLoopIfInfoState INTEGER, ospfLoopIfInfoPriority INTEGER, ospfLoopIfInfoDesignatedRouterIP IpAddress, ospfLoopIfInfoDesignatedRouterIpAddress IpAddress, ospfLoopIfInfoBackupDesignatedRouterIP IpAddress, ospfLoopIfInfoBackupDesignatedRouterIpAddress IpAddress, ospfLoopIfInfoHello INTEGER, ospfLoopIfInfoHelloMS INTEGER, ospfLoopIfInfoDead INTEGER, ospfLoopIfInfoDeadMS INTEGER, ospfLoopIfInfoWaitInterval Integer32, ospfLoopIfInfoWaitIntervalMS INTEGER, ospfLoopIfInfoRetransmit INTEGER, ospfLoopIfInfoTransitDelay INTEGER, ospfLoopIfInfoTotalNeighbours Integer32, ospfLoopIfInfoEvents Integer32, ospfLoopIfInfoAuthType INTEGER } ospfLoopIfInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF loopback interface number for which the OSPF info table is related." ::= { ospfLoopIfInfoEntry 1} ospfLoopIfInfoIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the OSPF loopback interface." ::= { ospfLoopIfInfoEntry 2 } ospfLoopIfInfoArea OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the area that the loopback interface belongs." ::= { ospfLoopIfInfoEntry 3 } ospfLoopIfInfoAdminStatus OBJECT-TYPE SYNTAX INTEGER { down(0), up(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Admin Status of the interface: down(0), up(1)." ::= { ospfLoopIfInfoEntry 4 } ospfLoopIfInfoPassive OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Passive status of the interface: disabled(0), enabled(1)." ::= { ospfLoopIfInfoEntry 5 } ospfLoopIfInfoPtop OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Point-to-point status of the interface: disabled(0), enabled(1)." ::= { ospfLoopIfInfoEntry 24 } ospfLoopIfInfoRouterIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The router ID of the switch." ::= { ospfLoopIfInfoEntry 6 } ospfLoopIfInfoState OBJECT-TYPE SYNTAX INTEGER { down(0), loopback(1), waiting(2), ptop(3), dr(4), backupdr(5), drother(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the interface: Down(0), Loopback(1), Waiting(2), P to P(3), DR(4), BackuDR(5), DR Other(6)." ::= { ospfLoopIfInfoEntry 7 } ospfLoopIfInfoPriority OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface router priority" ::= { ospfLoopIfInfoEntry 8 } ospfLoopIfInfoDesignatedRouterIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Designated Router IP (IP Address) for this OSPF interface." ::= { ospfLoopIfInfoEntry 9 } ospfLoopIfInfoDesignatedRouterIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Designated Router IP Address for this OSPF interface." ::= { ospfLoopIfInfoEntry 10 } ospfLoopIfInfoBackupDesignatedRouterIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Backup Designated Router IP for this OSPF interface." ::= { ospfLoopIfInfoEntry 11 } ospfLoopIfInfoBackupDesignatedRouterIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Backup Designated Router Ip Address for this OSPF interface." ::= { ospfLoopIfInfoEntry 12 } ospfLoopIfInfoHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The hello timer for this OSPF interface." ::= { ospfLoopIfInfoEntry 13 } ospfLoopIfInfoHelloMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Hello interval seconds(0), milliseconds(1)" ::= { ospfLoopIfInfoEntry 14 } ospfLoopIfInfoDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The dead timer for this OSPF interface." ::= { ospfLoopIfInfoEntry 15 } ospfLoopIfInfoDeadMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Dead interval seconds(0), milliseconds(1)" ::= { ospfLoopIfInfoEntry 16 } ospfLoopIfInfoWaitInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Wait interval for this OSPF interface." ::= { ospfLoopIfInfoEntry 17 } ospfLoopIfInfoWaitIntervalMS OBJECT-TYPE SYNTAX INTEGER { seconds(0), milliseconds(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Units of time measurement for Wait interval seconds(0), milliseconds(1)" ::= { ospfLoopIfInfoEntry 18 } ospfLoopIfInfoRetransmit OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "The retransmit interval for this OSPF interface." ::= { ospfLoopIfInfoEntry 19 } ospfLoopIfInfoTransitDelay OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "The transit delay for this OSPF interface." ::= { ospfLoopIfInfoEntry 20 } ospfLoopIfInfoTotalNeighbours OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Total number of neighbours for this OSPF interface." ::= { ospfLoopIfInfoEntry 21 } ospfLoopIfInfoEvents OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of events for this OSPF interface." ::= { ospfLoopIfInfoEntry 22 } ospfLoopIfInfoAuthType OBJECT-TYPE SYNTAX INTEGER { none(1), password(2), md5(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of authentication being used: none(1) - no authentication, password(2) - use password, md5(3) - use MD5 authentication." ::= { ospfLoopIfInfoEntry 23 } -- Ospfv3 Information ospf3GeneralInfo OBJECT IDENTIFIER ::= { ospf3Info 1 } ospf3Version OBJECT-TYPE SYNTAX INTEGER { ospfVersion3(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPF version." ::= { ospf3GeneralInfo 1 } ospf3RouterID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The router ID of the switch." ::= { ospf3GeneralInfo 2 } ospf3StartTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time when ospf has been started." ::= { ospf3GeneralInfo 3 } ospf3ProcessUptime OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time since ospf has been started." ::= { ospf3GeneralInfo 4 } -- ospf3LsTypesSupported OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The Link State Types that are supported." -- ::= { ospf3GeneralInfo 5 } ospf3AreaBorderRouter OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Area Border Router Role." ::= { ospf3GeneralInfo 5 } ospf3ASBoundaryRouter OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "AS Boundary Router Role." ::= { ospf3GeneralInfo 6 } ospf3ExternalLsa OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of external LSAs." ::= { ospf3GeneralInfo 7 } ospf3IntfCountForRouter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of interfaces for this router." ::= { ospf3GeneralInfo 8 } ospf3VlinkCountForRouter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of virtual links for this router." ::= { ospf3GeneralInfo 9 } ospf3NewLsaReceived OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of new LSAs reveived." ::= { ospf3GeneralInfo 10 } ospf3TotalLsaOriginated OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of LSAs originated." ::= { ospf3GeneralInfo 11 } ospf3TotalNumberOfAsScopeLsas OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of entries in the Link State Database." ::= { ospf3GeneralInfo 12 } ospf3TotalNeighbours OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of OSPF neighbours." ::= { ospf3GeneralInfo 13 } ospf3NbrInXchgOrLoadState OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of neighbours in the exchange or loading state." ::= { ospf3GeneralInfo 14 } -- ospf3NbrInExchState OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of neighbours in the exchange state." -- ::= { ospf3GeneralInfo 16 } -- -- ospf3NbrInFullState OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The number of neighbours in the Full state of exchange." -- ::= { ospf3GeneralInfo 17 } ospf3TotalAreas OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Total number of areas." ::= { ospf3GeneralInfo 15 } -- ospf3TotalTransitAreas OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The Total number of Transit areas." -- ::= { ospf3GeneralInfo 16 } ospf3TotalActiveAreas OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Total number of areas containing active interfaces." ::= { ospf3GeneralInfo 16 } ospf3TotalNssaAreas OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Total number of NSSA areas." ::= { ospf3GeneralInfo 17 } -- ospf3TotalStubAreas OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The Total number of STUB areas." -- ::= { ospf3GeneralInfo 19 } ospf3OverFlowState OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether router is in overflow state or not." DEFVAL { false } ::= { ospf3GeneralInfo 18 } ospf3SpfDelay OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION " The Delay at which routing calculation is carried after a topology change." DEFVAL {5} ::= { ospf3GeneralInfo 19 } ospf3SpfHoldTime OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION " The minimum time between two consecutive SPF calculations." DEFVAL {10} ::= { ospf3GeneralInfo 20 } ospf3ABRType OBJECT-TYPE SYNTAX INTEGER { standardABR (1), ciscoABR (2), ibmABR (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Different Types of ABRs supported" REFERENCE "RFC-3509 -- Alternative Implementations of OSPF Area Border Routers" DEFVAL { standardABR } ::= { ospf3GeneralInfo 21 } ospf3NssaAsbrDefRtTrans OBJECT-TYPE SYNTAX INTEGER { enabled (1) , disabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the P-Bit setting for the default Type-7 LSA generated by ASBR(which is not ABR).When disabled, P-Bit is clear in the generated default Lsa. When enabled, P-Bit is set in the generated Type-7 default Lsa. " DEFVAL { disabled } ::= { ospf3GeneralInfo 22 } ospf3AreaInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3AreaInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Area information." ::= { ospf3Info 2 } ospf3AreaInfoEntry OBJECT-TYPE SYNTAX Ospf3AreaInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPFv3 area." INDEX { ospf3AreaInfoIndex } ::= { ospf3AreaInfoTable 1 } Ospf3AreaInfoEntry ::= SEQUENCE { ospf3AreaInfoIndex Integer32, ospf3AreaInfoId IpAddress, ospf3AreaInfoStatus INTEGER, ospf3TotalNumberOfInterfaces Integer32, ospf3NumberOfInterfacesUp Integer32, -- ospf3AreaInfoAuthType INTEGER, ospf3AreaInfoSPF Integer32, ospf3NumberOfLsdbEntries Integer32, ospf3AreaInfoAreaBorderRouter Integer32, ospf3AreaInfoASBoundaryRouter Integer32, ospf3AreaInfoNeighborsFULLstate Integer32, ospf3AreaInfoVirtNeighborsFULLstate Integer32 } ospf3AreaInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 area number for which the OSPFv3 info table is related." ::= { ospf3AreaInfoEntry 1 } ospf3AreaInfoId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the OSPFv3 area." ::= { ospf3AreaInfoEntry 2 } ospf3AreaInfoStatus OBJECT-TYPE SYNTAX INTEGER { -- the following two values are states: -- these values may be read or written active(1), notInService(2), -- the following value is a state: -- this value may be read, but not written notReady(3), -- the following three values are -- actions: these values may be written, -- but are never read createAndGo(4), createAndWait(5), destroy(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Area Status: active(1), notInService(2), notReady(3)." ::= { ospf3AreaInfoEntry 3 } ospf3TotalNumberOfInterfaces OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of interfaces for this OSPFv3 area." ::= { ospf3AreaInfoEntry 4 } ospf3NumberOfInterfacesUp OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of interfaces UP in area." ::= { ospf3AreaInfoEntry 5 } -- ospf3AreaInfoAuthType OBJECT-TYPE -- SYNTAX INTEGER { -- none(1), -- password(2), -- md5(3) -- } -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Type of authentication being used: -- none(1) - no authentication -- password(2) - use password -- md5(3) - use MD5 authentication." -- ::= { ospf3AreaInfoEntry 6 } ospf3AreaInfoSPF OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times SPF ran." ::= { ospf3AreaInfoEntry 6 } ospf3NumberOfLsdbEntries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Area-scope link state advertisements in this area's link state database." ::= { ospf3AreaInfoEntry 7 } ospf3AreaInfoAreaBorderRouter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Area Border Router count." ::= { ospf3AreaInfoEntry 8 } ospf3AreaInfoASBoundaryRouter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The AS Boundary Router count." ::= { ospf3AreaInfoEntry 9 } -- ospf3AreaInfoTotalNeighbours OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The total number of OSPFv3 neighbors." -- ::= { ospf3AreaInfoEntry 11 } -- -- ospf3AreaInfoNeighborsINITstate OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Total neighbors in INIT state." -- ::= { ospf3AreaInfoEntry 12 } -- -- ospf3AreaInfoNeighborsEXCHstate OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Total neighbors in EXCH state." -- ::= { ospf3AreaInfoEntry 13 } ospf3AreaInfoNeighborsFULLstate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total neighbors in FULL state." ::= { ospf3AreaInfoEntry 10 } ospf3AreaInfoVirtNeighborsFULLstate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total neighbors in FULL state." ::= { ospf3AreaInfoEntry 11 } ospf3IntfInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3IntfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Interface information." ::= { ospf3Info 3 } ospf3IntfInfoEntry OBJECT-TYPE SYNTAX Ospf3IntfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPFv3 interface." INDEX { ospf3IfInfoIndex } ::= { ospf3IntfInfoTable 1 } Ospf3IntfInfoEntry ::= SEQUENCE { ospf3IfInfoIndex Integer32, ospf3IfInfoInstanceID Unsigned32, ospf3IfInfoLLocalAddress DisplayString, ospf3IfInfoAreaID IpAddress, ospf3IfInfoAdminStatus INTEGER, ospf3IfInfoPassive INTEGER, ospf3IfInfoNetworkType INTEGER, ospf3IfInfoState INTEGER, ospf3IfInfoPriority INTEGER, ospf3IfInfoDesignatedRouterID IpAddress, ospf3IfInfoBackupDesignatedRouterID IpAddress, ospf3IfInfoHello INTEGER, ospf3IfInfoDead INTEGER, ospf3IfInfoPoll Integer32, ospf3IfInfoRetransmit INTEGER, ospf3IfInfoTransitDelay INTEGER, ospf3IfInfoTotalNeighbours Integer32, ospf3IfInfoEvents Integer32, ospf3IfInfoMetricCost Integer32 , ospf3IfInfoAuthSpi Unsigned32, ospf3IfInfoAuthEnable INTEGER, ospf3IfInfoAuthType INTEGER, ospf3IfInfoAuthKey OCTET STRING, ospf3IfInfoEncrySpi Unsigned32, ospf3IfInfoEncryEnable INTEGER, ospf3IfInfoEncryType INTEGER, ospf3IfInfoEncryKey OCTET STRING, ospf3IfInfoEncryAuthType INTEGER, ospf3IfInfoEncryAuthKey OCTET STRING , ospf3IfInfoLsaSupress INTEGER } ospf3IfInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 interface number for which the OSPFv3 info table is related." ::= { ospf3IntfInfoEntry 1 } ospf3IfInfoInstanceID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 interface instance id." ::= { ospf3IntfInfoEntry 2 } ospf3IfInfoLLocalAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the OSPFv3 interface." ::= { ospf3IntfInfoEntry 3 } ospf3IfInfoAreaID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The AreaID of the area that the interface belongs." ::= { ospf3IntfInfoEntry 4 } ospf3IfInfoAdminStatus OBJECT-TYPE SYNTAX INTEGER { down(0), up(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Admin Status of the interface: down(0), up(1)." ::= { ospf3IntfInfoEntry 5 } ospf3IfInfoPassive OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Passive status of the interface: disabled(0), enabled(1)." ::= { ospf3IntfInfoEntry 6 } ospf3IfInfoNetworkType OBJECT-TYPE SYNTAX INTEGER { broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Network type of the interface: broadcast(1),nbma(2),pointToPoint(3),pointToMultipoint(5)." ::= { ospf3IntfInfoEntry 7 } ospf3IfInfoState OBJECT-TYPE SYNTAX INTEGER { down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7), standby(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the interface: Down(0), Loopback(1), Waiting(2), P to P(3), DR(4), BackuDR(5), DR Other(6)." ::= { ospf3IntfInfoEntry 8 } ospf3IfInfoPriority OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Interface router priority" ::= { ospf3IntfInfoEntry 9 } ospf3IfInfoDesignatedRouterID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 Designated Router ID for this OSPFv3 interface." ::= { ospf3IntfInfoEntry 10 } ospf3IfInfoBackupDesignatedRouterID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 Backup Designated Router ID for this OSPFv3 interface." ::= { ospf3IntfInfoEntry 11 } ospf3IfInfoHello OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The hello timer for this OSPF3 interface." ::= { ospf3IntfInfoEntry 12 } ospf3IfInfoDead OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The dead timer for this OSPFv3 interface." ::= { ospf3IntfInfoEntry 13 } ospf3IfInfoPoll OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 Poll interval for this OSPFv3 interface." ::= { ospf3IntfInfoEntry 14 } ospf3IfInfoRetransmit OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "The retransmit interval for this OSPFv3 interface." ::= { ospf3IntfInfoEntry 15 } ospf3IfInfoTransitDelay OBJECT-TYPE SYNTAX INTEGER (1..3600) MAX-ACCESS read-only STATUS current DESCRIPTION "The transit delay for this OSPFv3 interface." ::= { ospf3IntfInfoEntry 16 } ospf3IfInfoTotalNeighbours OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of neighbours for this OSPFv3 interface." ::= { ospf3IntfInfoEntry 17 } ospf3IfInfoEvents OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of events for this OSPF3 interface." ::= { ospf3IntfInfoEntry 18 } ospf3IfInfoMetricCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of this OSPF3 interface." ::= { ospf3IntfInfoEntry 19 } ospf3IfInfoAuthSpi OBJECT-TYPE SYNTAX Unsigned32 (256..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "Authentication Spi Id(256 - 4294967295)" ::= { ospf3IntfInfoEntry 20 } ospf3IfInfoAuthEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Authentication Status disabled(0), enabled(1)" ::= { ospf3IntfInfoEntry 21 } ospf3IfInfoAuthType OBJECT-TYPE SYNTAX INTEGER { none(0), md5(2), sha1(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Authentication Type none(0), md5(2), sha1(1)" ::= { ospf3IntfInfoEntry 22 } ospf3IfInfoAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "Authentication Key Hex-string MD5 key - 32 chars (128 bits) Hex-string SHA-1 key - 40 chars (160 bits)" ::= { ospf3IntfInfoEntry 23 } ospf3IfInfoEncrySpi OBJECT-TYPE SYNTAX Unsigned32 (256..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "Encryption Spi Id(256 - 4294967295)" ::= { ospf3IntfInfoEntry 24 } ospf3IfInfoEncryEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Encryption Status disabled(0), enabled(1)" ::= { ospf3IntfInfoEntry 25 } ospf3IfInfoEncryType OBJECT-TYPE SYNTAX INTEGER { null(0), tripledes(2), aes(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Encryption Authentication Type null(0), 3des(2), aes(3)" ::= { ospf3IntfInfoEntry 26 } ospf3IfInfoEncryKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "Encryption Key Hex-string AES key - 32 chars (128 bits) Hex-string 3DES key - 48 chars (192 bits)" ::= { ospf3IntfInfoEntry 27 } ospf3IfInfoEncryAuthType OBJECT-TYPE SYNTAX INTEGER { none(0), md5(2), sha1(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Encryption Authentication Type none(0), md5(2), sha1(1)" ::= { ospf3IntfInfoEntry 28 } ospf3IfInfoEncryAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "Encryption Authentication Key Hex-string MD5 key - 32 chars (128 bits) Hex-string SHA-1 key - 40 chars (160 bits)" ::= { ospf3IntfInfoEntry 29 } ospf3IfInfoLsaSupress OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Lsa supression status of the interface: disabled(0), enabled(1)." ::= { ospf3IntfInfoEntry 30 } -- OSPFv3 Virtual Interface Table ospf3VirtIntfInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3VirtIntfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Virtual Interface information." ::= { ospf3Info 4 } ospf3VirtIntfInfoEntry OBJECT-TYPE SYNTAX Ospf3VirtIntfInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single virtual interface." INDEX { ospf3VirtIfInfoIndex } ::= { ospf3VirtIntfInfoTable 1 } Ospf3VirtIntfInfoEntry ::= SEQUENCE { ospf3VirtIfInfoIndex Integer32, ospf3VirtIfInfoAreaId IpAddress, ospf3VirtIfInfoNeighbor IpAddress, ospf3VirtIfInfoTransitDelay INTEGER, ospf3VirtIfInfoRetransInterval INTEGER, ospf3VirtIfInfoHelloInterval INTEGER, ospf3VirtIfInfoRtrDeadInterval INTEGER, ospf3VirtIfInfoState INTEGER, ospf3VirtIfInfoEvents INTEGER, ospf3VirtIfInfoStatus INTEGER, ospf3VirtIfInfoLinkScopeLsaCount INTEGER, ospf3VirtIfInfoLinkLsaCksumSum INTEGER } ospf3VirtIfInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 virtual interface number for which the OSPFv3 info table is related." ::= { ospf3VirtIntfInfoEntry 1 } ospf3VirtIfInfoAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The transit area that the virtual link traverses. By definition, this is not Area 0." ::= { ospf3VirtIntfInfoEntry 2 } ospf3VirtIfInfoNeighbor OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the virtual neighbor." ::= { ospf3VirtIntfInfoEntry 3 } ospf3VirtIfInfoTransitDelay OBJECT-TYPE SYNTAX INTEGER UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a Link State Update packet over this interface." DEFVAL { 1 } ::= { ospf3VirtIntfInfoEntry 5 } ospf3VirtIfInfoRetransInterval OBJECT-TYPE SYNTAX INTEGER UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds between link state advertisement retransmissions for adjacencies belonging to this interface. This value is also used when retransmitting database description and Link State Request packets. This value should be well over the expected round-trip time." DEFVAL { 5 } ::= { ospf3VirtIntfInfoEntry 6 } ospf3VirtIfInfoHelloInterval OBJECT-TYPE SYNTAX INTEGER UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor." DEFVAL { 10 } ::= { ospf3VirtIntfInfoEntry 7 } ospf3VirtIfInfoRtrDeadInterval OBJECT-TYPE SYNTAX INTEGER UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor." DEFVAL { 60 } ::= { ospf3VirtIntfInfoEntry 8 } ospf3VirtIfInfoState OBJECT-TYPE SYNTAX INTEGER { down(1), pointToPoint(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPF virtual interface states." ::= { ospf3VirtIntfInfoEntry 9 } ospf3VirtIfInfoEvents OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of state changes or error events on this virtual link. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime." ::= { ospf3VirtIntfInfoEntry 10 } ospf3VirtIfInfoStatus OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object permits management of the table by facilitating actions such as row creation, construction, and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified." ::= { ospf3VirtIntfInfoEntry 11 } ospf3VirtIfInfoLinkScopeLsaCount OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Link-scope link state advertisements in this virtual link's link state database." ::= { ospf3VirtIntfInfoEntry 12 } ospf3VirtIfInfoLinkLsaCksumSum OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 32-bit unsigned sum of the Link-scope link state advertisements' LS checksums contained in this virtual link's link state database. The sum can be used to determine if there has been a change in a router's link state database or to compare the link state database of two routers." ::= { ospf3VirtIntfInfoEntry 13 } -- OSPF3 Interface/Nbr Info Table ospf3IfNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3IfNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 Interface Neighbor information." ::= { ospf3Info 5 } ospf3IfNbrEntry OBJECT-TYPE SYNTAX Ospf3IfNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a OSPFv3 interface, neighbor pair." INDEX { ospf3IfNbrInfoIndex } ::= { ospf3IfNbrTable 1 } Ospf3IfNbrEntry ::= SEQUENCE { ospf3IfNbrInfoIndex Integer32, ospf3IfNbrIntfIndex Integer32, ospf3IfNbrIntfInstanceID Unsigned32, ospf3IfNbrRtrID IpAddress, ospf3IfNbrIpAddress DisplayString, ospf3IfNbrPriority Integer32, ospf3IfNbrState INTEGER, ospf3IfNbrEvents Integer32 } ospf3IfNbrInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 neighbor table entry index for which this table is related." ::= { ospf3IfNbrEntry 1} ospf3IfNbrIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 Interface number for which this Nbr table is related." ::= { ospf3IfNbrEntry 2} ospf3IfNbrIntfInstanceID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 Interface instance id for which this Nbr table is related." ::= { ospf3IfNbrEntry 3} ospf3IfNbrRtrID OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit unsigned integer uniquely identifying the neighboring router in the Autonomous System." ::= { ospf3IfNbrEntry 4 } ospf3IfNbrIpAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 address of the neighbor associated with the local link." ::= { ospf3IfNbrEntry 5 } ospf3IfNbrPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The priority of the OSPFv3 neighbor." ::= { ospf3IfNbrEntry 6 } ospf3IfNbrState OBJECT-TYPE SYNTAX INTEGER { down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the relationship with this neighbor." ::= { ospf3IfNbrEntry 7 } ospf3IfNbrEvents OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this neighbor relationship has changed state or an error has occurred." ::= { ospf3IfNbrEntry 8 } -- OSPFv3 Interface/Routes Table ospf3RoutesInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF Ospf3RoutesInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of OSPFv3 routes information." ::= { ospf3Info 6 } ospf3RoutesInfoEntry OBJECT-TYPE SYNTAX Ospf3RoutesInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "OSPFv3 routes information." INDEX { ospf3RoutesInfoIndex } ::= { ospf3RoutesInfoTable 1 } Ospf3RoutesInfoEntry ::= SEQUENCE { ospf3RoutesInfoIndex Integer32, ospf3RoutesInfoDestination DisplayString, ospf3RoutesInfoPrefixLen INTEGER, ospf3RoutesInfoNextHop DisplayString, ospf3RoutesInfoType INTEGER, ospf3RoutesInfoAreaId IpAddress, ospf3RoutesInfoCost INTEGER, ospf3RoutesInfoType2Cost INTEGER, ospf3RoutesInfoInterfaceIndex Integer32 } ospf3RoutesInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPFv3 route table entry index for which this table is related." ::= { ospf3RoutesInfoEntry 1 } ospf3RoutesInfoDestination OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " The Destination IPv6 Address of this route." ::= { ospf3RoutesInfoEntry 2 } ospf3RoutesInfoPrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates the prefix length of the destination Address." ::= { ospf3RoutesInfoEntry 3 } ospf3RoutesInfoNextHop OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Next Hop IPv6 Address for this route. For direct routes it has the value ::0." ::= { ospf3RoutesInfoEntry 4 } ospf3RoutesInfoType OBJECT-TYPE SYNTAX INTEGER { intraArea (1), interArea (2), type1External (3), type2External (4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the route" ::= { ospf3RoutesInfoEntry 5 } ospf3RoutesInfoAreaId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " Area ID associated with the route " ::= { ospf3RoutesInfoEntry 6 } ospf3RoutesInfoCost OBJECT-TYPE SYNTAX INTEGER (1..'FFFFFF'h) MAX-ACCESS read-only STATUS current DESCRIPTION " It is a Type 1 external metrics which is expressed in the same units as OSPF interface cost ie. in terms of the OSPF link state metric. If Type1 and Type2 cost are present, Type1 external metrics always take precedence." ::= { ospf3RoutesInfoEntry 7 } ospf3RoutesInfoType2Cost OBJECT-TYPE SYNTAX INTEGER (1..'FFFFFF'h) MAX-ACCESS read-only STATUS current DESCRIPTION " Type 2 external metrics are configured with the cost greater than any path internal to the AS. Use of Type 2 external metrics assumes that routing between AS is the major cost of routing a packet, and eliminates the need for conversion of external costs to internal link state metrics." ::= { ospf3RoutesInfoEntry 8 } ospf3RoutesInfoInterfaceIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " Interface Index associated with the route" ::= { ospf3RoutesInfoEntry 9 } -- Gateway Information gatewayInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF GatewayInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table containing information for the default gateways." ::= { gatewayInfo 1 } gatewayInfoEntry OBJECT-TYPE SYNTAX GatewayInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the gateway information table" INDEX { gatewayInfoIndex } ::= { gatewayInfoTable 1 } GatewayInfoEntry ::= SEQUENCE { gatewayInfoIndex Integer32, gatewayInfoAddr IpAddress, gatewayInfoStatus INTEGER } gatewayInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The gateway number for which the information is related." ::= { gatewayInfoEntry 1} gatewayInfoAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the default gateway." ::= { gatewayInfoEntry 2 } gatewayInfoStatus OBJECT-TYPE SYNTAX INTEGER { up(1), failed(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of the default gateway." ::= { gatewayInfoEntry 4 } ipInfoBootpRelayState OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of BOOTP relay." ::= { ipInfo 4 } ipInfoBootpRelayAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of BOOTP server." ::= { ipInfo 5 } ipInfoBootpRelayAddr2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of second BOOTP server." ::= { ipInfo 6 } ipInfoFwdState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "IP forwarding global state." ::= { ipInfo 7 } ipInfoFwdDirectedBcast OBJECT-TYPE SYNTAX INTEGER { enabled(2), disabled(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of forwarding directed broadcasts." ::= { ipInfo 8 } -- igmp snooping info table igmpInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IGMP group membership information." ::= { igmpInfo 1 } igmpInfoEntry OBJECT-TYPE SYNTAX IgmpInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an IGMP group member ." INDEX { igmpInfoIndex } ::= { igmpInfoTable 1 } IgmpInfoEntry ::= SEQUENCE { igmpInfoIndex INTEGER, igmpInfoGroupId IpAddress, igmpInfoVlanId INTEGER, igmpInfoSrcTrunk Unsigned32, igmpInfoSrcPort PortNumber, igmpInfoVersion INTEGER, igmpInfoExpires DisplayString, igmpInfoMode INTEGER, igmpInfoSourceIp IpAddress, igmpInfoFwd INTEGER, igmpInfoGrpExpires DisplayString } igmpInfoIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The igmp group number for which the IGMP info table is related." ::= { igmpInfoEntry 1} igmpInfoGroupId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the IGMP group." ::= { igmpInfoEntry 2} igmpInfoVlanId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID for this IGMP group." ::= { igmpInfoEntry 3} igmpInfoSrcTrunk OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The downstream trunk number." ::= { igmpInfoEntry 4} igmpInfoSrcPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The downstream port number." ::= { igmpInfoEntry 5} igmpInfoVersion OBJECT-TYPE SYNTAX INTEGER { v3(1), v2(2), v1(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Version of IGMP host." ::= { igmpInfoEntry 6} igmpInfoExpires OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The expiration time for this host." ::= { igmpInfoEntry 7 } igmpInfoMode OBJECT-TYPE SYNTAX INTEGER { exclude(1), include(2), na(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMPv3 filter-mode for this host. Returned values: exclude(1) - the IGMPv3 filter-mode is exclude. include(2) - the IGMPv3 filter-mode is include. na(3) - not applicable(v1 and v2)." ::= { igmpInfoEntry 8 } igmpInfoSourceIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source IP address of the IGMP group." ::= { igmpInfoEntry 9 } igmpInfoFwd OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMPv3 forwarding for this source/group IP for this host." ::= { igmpInfoEntry 10 } igmpInfoGrpExpires OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The expiration time for the group." ::= { igmpInfoEntry 11 } igmpMrtrInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpMrtrInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of IGMP mrouters." ::= { igmpInfo 2 } igmpMrtrInfoEntry OBJECT-TYPE SYNTAX IgmpMrtrInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an IGMP mrouter." INDEX { igmpMrtrInfoIndex } ::= { igmpMrtrInfoTable 1 } IgmpMrtrInfoEntry ::= SEQUENCE { igmpMrtrInfoIndex INTEGER, igmpMrtrInfoVlanId INTEGER, igmpMrtrInfoPortId DisplayString, igmpMrtrInfoVersion INTEGER, igmpMrtrInfoExpires DisplayString, igmpMrtrInfoMrt Integer32, igmpMrtrInfoQrv INTEGER, igmpMrtrInfoQqic INTEGER, igmpMrtrInfoSrcIp IpAddress } igmpMrtrInfoIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The mrouter number for which the IGMP mrouter info table is related." ::= { igmpMrtrInfoEntry 1} igmpMrtrInfoVlanId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID on which this IGMP mrouter is attached." ::= { igmpMrtrInfoEntry 2} igmpMrtrInfoPortId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The port/portchannel alias on which this IGMP mrouter is attached." ::= { igmpMrtrInfoEntry 3} igmpMrtrInfoVersion OBJECT-TYPE SYNTAX INTEGER { v1(1), v2(2), v3(3), pim(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The version of this IGMP mrouter." ::= { igmpMrtrInfoEntry 4} igmpMrtrInfoExpires OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The expiration time for this mrouter." ::= { igmpMrtrInfoEntry 5 } igmpMrtrInfoMrt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum Query Response time of this IGMP mrouter." ::= { igmpMrtrInfoEntry 6 } igmpMrtrInfoQrv OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Querier Robustness value of this IGMP mrouter." ::= { igmpMrtrInfoEntry 7 } igmpMrtrInfoQqic OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Querier query interval code of this IGMP mrouter." ::= { igmpMrtrInfoEntry 8 } igmpMrtrInfoSrcIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Source IP of this IGMP mrouter." ::= { igmpMrtrInfoEntry 10 } igmpClearTables OBJECT-TYPE SYNTAX INTEGER { ok(0), clearGroups(1), clearMrouters(2), clearAll(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Clear the IGMP tables. When setting clearGroups(1), the dynamic groups are removed, when setting clearMrouters(2), the mrouter tables are removed and when setting clearAll(3), both the dynamic groups and the mrouter tables are removed. When read, ok(0) is always returned." ::= { igmpInfo 3 } -- nbr Info Table nbrInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF NbrInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of nbrcache information." ::= { nbrInfo 1 } nbrInfoEntry OBJECT-TYPE SYNTAX NbrInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about neighbor discovery protocol." INDEX { nbrInfoIndex } ::= { nbrInfoTable 1 } NbrInfoEntry ::= SEQUENCE { nbrInfoIndex Integer32, nbrInfoDestIp DisplayString, nbrInfoState INTEGER, nbrInfoMacAddr PhysAddress, nbrInfoVlanId Integer32, nbrInfoPortNum Integer32, nbrInfoAge Integer32, nbrInfoInterface Integer32 } nbrInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the nbrcache entry." ::= { nbrInfoEntry 1 } nbrInfoDestIp OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address of the nbrcache entry." ::= { nbrInfoEntry 2 } nbrInfoState OBJECT-TYPE SYNTAX INTEGER { static(1), reach(2), incomplete(3), stale(4), delay(5), probe(6), unknown(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the nbrcache entry." ::= { nbrInfoEntry 3 } nbrInfoMacAddr OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address for the nbrcache entry." ::= { nbrInfoEntry 4 } nbrInfoVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN identifier for the nbrcache entry." ::= { nbrInfoEntry 5 } nbrInfoPortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number on which this entry's equivalence is effective." ::= { nbrInfoEntry 6 } nbrInfoAge OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The used time for the nbrcache entry." ::= { nbrInfoEntry 7 } nbrInfoInterface OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number for which the destination address is applicable." ::= { nbrInfoEntry 8 } nbrClear OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the Nbr cache, When read ok(1) is returned." ::= { nbrInfo 2 } -- ipv6 PMTU Info Table ipv6PmtuInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF Ipv6PmtuInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Ipv6 PMTU entries." ::={ ipv6PmtuInfo 1 } ipv6PmtuInfoEntry OBJECT-TYPE SYNTAX Ipv6PmtuInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the ipv6 PMTU entries table." INDEX { ipv6PmtuInfoIndx } ::= { ipv6PmtuInfoTable 1 } Ipv6PmtuInfoEntry ::= SEQUENCE { ipv6PmtuInfoIndx Integer32, ipv6PmtuInfoDestIp DisplayString, ipv6PmtuInfoSinceTime DisplayString, ipv6PmtuInfoValue Integer32 } ipv6PmtuInfoIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of this ipv6 PMTU table entries." ::= { ipv6PmtuInfoEntry 1 } ipv6PmtuInfoDestIp OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The destination of the pMTU." ::= { ipv6PmtuInfoEntry 2 } ipv6PmtuInfoSinceTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The addubt time of the pMTU." ::= { ipv6PmtuInfoEntry 3 } ipv6PmtuInfoValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vlaue of this ipv6 PMTU table entries." ::= { ipv6PmtuInfoEntry 4 } -- route6 Info Table ipRoute6InfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IpRoute6InfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of run-time IP6 routes." ::= { ipRoute6Info 1 } ipRoute6InfoEntry OBJECT-TYPE SYNTAX IpRoute6InfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the run-time IP6 route table." INDEX { ipRoute6InfoIndx } ::= { ipRoute6InfoTable 1 } IpRoute6InfoEntry ::= SEQUENCE { ipRoute6InfoIndx Integer32, ipRoute6InfoDestIp DisplayString, ipRoute6InfoPrefLen INTEGER, ipRoute6InfoInterface Integer32, ipRoute6InfoNextHop DisplayString, ipRoute6InfoProto INTEGER } ipRoute6InfoIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of this route6 table." ::= { ipRoute6InfoEntry 1 } ipRoute6InfoDestIp OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The destination of the route." ::= { ipRoute6InfoEntry 2 } ipRoute6InfoPrefLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination prefix length of the route." ::= { ipRoute6InfoEntry 3} ipRoute6InfoInterface OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface of the route." ::= { ipRoute6InfoEntry 4 } ipRoute6InfoNextHop OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The next hop of the route." ::= { ipRoute6InfoEntry 5 } ipRoute6InfoProto OBJECT-TYPE SYNTAX INTEGER { local(2), static(3), nbrdis(4), ripng(5), ospf(6), intmgmt(10), extmgmt(11), intmgmtND(12), extmgmtND(13) } MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol type of the route." ::= { ipRoute6InfoEntry 6 } -- IPv6 Gateway Info gatewayIPv6InfoTable OBJECT-TYPE SYNTAX SEQUENCE OF GatewayIPv6InfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table containing information for the IPv6 default gateways." ::= { gatewayIPv6Info 1 } gatewayIPv6InfoEntry OBJECT-TYPE SYNTAX GatewayIPv6InfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the IPv6 gateway information table" INDEX { ipGatewayIPv6InfoIndex } ::= { gatewayIPv6InfoTable 1 } GatewayIPv6InfoEntry ::= SEQUENCE { ipGatewayIPv6InfoIndex Integer32, ipGatewayIPv6InfoAddr IpAddress, ipGatewayIPv6InfoState INTEGER } ipGatewayIPv6InfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 gateway number for which the information is related." ::= { gatewayIPv6InfoEntry 1} ipGatewayIPv6InfoAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address for the IPv6 default gateway." ::= { gatewayIPv6InfoEntry 2 } ipGatewayIPv6InfoState OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state for the IPv6 Default Gateway." ::= { gatewayIPv6InfoEntry 3 } -- nbrcache Info Table rip2GeneralInfo OBJECT IDENTIFIER ::= { rip2Info 1 } ripInfoState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "RIP global state." ::= { rip2GeneralInfo 1 } ripInfoUpdatePeriod OBJECT-TYPE SYNTAX INTEGER (1..120) MAX-ACCESS read-only STATUS current DESCRIPTION "Update Period in seconds." ::= { rip2GeneralInfo 2 } rip2InfoIntfTable OBJECT-TYPE SYNTAX SEQUENCE OF RipInfoIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The information table of RIP." ::= { rip2Info 2 } ripInfoIntfEntry OBJECT-TYPE SYNTAX RipInfoIntfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about RIP on IP interface." INDEX { ripInfoIntfIndex } ::= { rip2InfoIntfTable 1 } RipInfoIntfEntry ::= SEQUENCE { ripInfoIntfIndex Integer32, ripInfoIntfVersion INTEGER, ripInfoIntfAddress IpAddress, ripInfoIntfState INTEGER, ripInfoIntfListen INTEGER, ripInfoIntfTrigUpdate INTEGER, ripInfoIntfMcastUpdate INTEGER, ripInfoIntfPoisonReverse INTEGER, ripInfoIntfSupply INTEGER, ripInfoIntfMetric INTEGER, ripInfoIntfAuth INTEGER, ripInfoIntfKey DisplayString, ripInfoIntfDefault INTEGER } ripInfoIntfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface number for which the RIP information is related." ::= { ripInfoIntfEntry 1 } ripInfoIntfVersion OBJECT-TYPE SYNTAX INTEGER { ripVersion1(1), ripVersion2(2), ripVersionBoth(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "RIP version." ::= { ripInfoIntfEntry 2 } ripInfoIntfAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The interface address." ::= { ripInfoIntfEntry 3 } ripInfoIntfState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of RIP protocol." ::= { ripInfoIntfEntry 4 } ripInfoIntfListen OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of listening to route updates." ::= { ripInfoIntfEntry 5 } ripInfoIntfTrigUpdate OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of triggered updates." ::= { ripInfoIntfEntry 6 } ripInfoIntfMcastUpdate OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of multicast updates." ::= { ripInfoIntfEntry 7 } ripInfoIntfPoisonReverse OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of RIP poison reverse." ::= { ripInfoIntfEntry 8 } ripInfoIntfSupply OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of supplying route updates." ::= { ripInfoIntfEntry 9 } ripInfoIntfMetric OBJECT-TYPE SYNTAX INTEGER (1..15) MAX-ACCESS read-only STATUS current DESCRIPTION "RIP route metric for this interface." ::= { ripInfoIntfEntry 10 } ripInfoIntfAuth OBJECT-TYPE SYNTAX INTEGER { none(1), password(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of Authentication used on this interface." ::= { ripInfoIntfEntry 11 } ripInfoIntfKey OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "RIP update authentication password." ::= { ripInfoIntfEntry 12 } ripInfoIntfDefault OBJECT-TYPE SYNTAX INTEGER { both(1), listen(2), supply(3), none(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies what RIP does with default routes." ::= { ripInfoIntfEntry 13 } rip2InfoRtrTable OBJECT-TYPE SYNTAX SEQUENCE OF RipInfoRtrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The routing information table of RIP." ::= { rip2Info 3 } ripInfoRtrEntry OBJECT-TYPE SYNTAX RipInfoRtrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about RIP routes." INDEX { ripInfoRtrIndex } ::= { rip2InfoRtrTable 1 } RipInfoRtrEntry ::= SEQUENCE { ripInfoRtrIndex Integer32, ripInfoRtrDestIp IpAddress, ripInfoRtrMask IpAddress, ripInfoRtrGateway IpAddress, ripInfoRtrMetric Integer32 } ripInfoRtrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index number of RIP route." ::= { ripInfoRtrEntry 1 } ripInfoRtrDestIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination ip address of this route." ::= { ripInfoRtrEntry 2 } ripInfoRtrMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination ip mask of this route." ::= { ripInfoRtrEntry 3 } ripInfoRtrGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The next-hop router address for this route." ::= { ripInfoRtrEntry 4 } ripInfoRtrMetric OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The metric for this route." ::= { ripInfoRtrEntry 10 } -- L3 BGP Info bgpInfoPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpInfoPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of BGP peer in the current configuration block." ::= { bgpInfo 1 } bgpInfoPeerEntry OBJECT-TYPE SYNTAX BgpInfoPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a BGP peer." INDEX { bgpInfoPeerIndex } ::= { bgpInfoPeerTable 1 } BgpInfoPeerEntry ::= SEQUENCE { bgpInfoPeerIndex Integer32, bgpInfoPeerRemoteAddr IpAddress, bgpInfoPeerVersion Integer32, bgpInfoPeerTtl Integer32, bgpInfoPeerRemoteAs Integer32, bgpInfoPeerRouterId IpAddress, bgpInfoPeerState INTEGER, bgpInfoPeerLastState INTEGER, bgpInfoTotalReceivedPackets Integer32, bgpInfoTotalSentPackets Integer32, bgpInfoReceivedUpdates Integer32, bgpInfoSentUpdates Integer32, bgpInfoKeepalive Integer32, bgpInfoHoldtime Integer32, bgpInfoMinAdvTime Integer32, bgpInfoLastErrorCode Integer32, bgpInfoLastErrorSubCode Integer32, bgpInfoEstTransitions Integer32 } bgpInfoPeerIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP peer number for which the BGP peer table is related." ::= { bgpInfoPeerEntry 1 } bgpInfoPeerRemoteAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The remote IP address of the BGP peer." ::= { bgpInfoPeerEntry 2 } bgpInfoPeerVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The version negotiated by the BGP peer." ::= { bgpInfoPeerEntry 3 } bgpInfoPeerTtl OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time-to-live value of the BGP peer IP datagram." ::= { bgpInfoPeerEntry 4 } bgpInfoPeerRemoteAs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The remote IP address of the BGP peer." ::= { bgpInfoPeerEntry 5 } bgpInfoPeerRouterId OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The router IP address." ::= { bgpInfoPeerEntry 6 } bgpInfoPeerState OBJECT-TYPE SYNTAX INTEGER { idle(1), connect(2), active(3), openSent(4), openConfirm(5), established(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP status." ::= { bgpInfoPeerEntry 7 } bgpInfoPeerLastState OBJECT-TYPE SYNTAX INTEGER { idle(1), connect(2), active(3), openSent(4), openConfirm(5), established(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP old status." ::= { bgpInfoPeerEntry 8 } bgpInfoTotalReceivedPackets OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received packets." ::= { bgpInfoPeerEntry 9 } bgpInfoTotalSentPackets OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of sent packets." ::= { bgpInfoPeerEntry 10 } bgpInfoReceivedUpdates OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of received updates." ::= { bgpInfoPeerEntry 11 } bgpInfoSentUpdates OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of sent updates." ::= { bgpInfoPeerEntry 12 } bgpInfoKeepalive OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The keep alive time." ::= { bgpInfoPeerEntry 13 } bgpInfoHoldtime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The hold time." ::= { bgpInfoPeerEntry 14 } bgpInfoMinAdvTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The MinAdvTime." ::= { bgpInfoPeerEntry 15 } bgpInfoLastErrorCode OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The last error code." ::= { bgpInfoPeerEntry 16 } bgpInfoLastErrorSubCode OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The last error subcode." ::= { bgpInfoPeerEntry 17 } bgpInfoEstTransitions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The established state transitions." ::= { bgpInfoPeerEntry 18 } bgpInfoSummaryTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpInfoSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of BGP Peer Information." ::= { bgpInfo 2 } bgpInfoSummaryEntry OBJECT-TYPE SYNTAX BgpInfoSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a BGP Peer." INDEX { bgpInfoSummaryIndex } ::= { bgpInfoSummaryTable 1 } BgpInfoSummaryEntry ::= SEQUENCE { bgpInfoSummaryIndex Integer32, bgpInfoSummaryRemoteAddr IpAddress, bgpInfoSummaryVersion Integer32, bgpInfoSummaryRemoteAs Integer32, bgpInfoSummaryState INTEGER, bgpInfoSummaryTotalReceivedPackets Integer32, bgpInfoSummaryTotalSentPackets Integer32 } bgpInfoSummaryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP Peer number for which the BGP Peer table is related." ::= { bgpInfoSummaryEntry 1 } bgpInfoSummaryRemoteAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The remote IP address of the BGP Peer." ::= { bgpInfoSummaryEntry 2 } bgpInfoSummaryVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The version negotiated by the BGP Peer." ::= { bgpInfoSummaryEntry 3 } bgpInfoSummaryRemoteAs OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Remote AS." ::= { bgpInfoSummaryEntry 4 } bgpInfoSummaryState OBJECT-TYPE SYNTAX INTEGER { idle(1), connect(2), active(3), openSent(4), openConfirm(5), established(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP status." ::= { bgpInfoSummaryEntry 5 } bgpInfoSummaryTotalReceivedPackets OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received packets." ::= { bgpInfoSummaryEntry 6 } bgpInfoSummaryTotalSentPackets OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of sent packets." ::= { bgpInfoSummaryEntry 7 } bgpInfoRtrTable OBJECT-TYPE SYNTAX SEQUENCE OF BgpInfoRtrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of BGP router run-time information" ::= { bgpInfo 3 } bgpInfoRtrTableEntry OBJECT-TYPE SYNTAX BgpInfoRtrTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The run-time information about a BGP router" INDEX { bgpInfoIndex } ::= { bgpInfoRtrTable 1 } BgpInfoRtrTableEntry ::= SEQUENCE { bgpInfoIndex IpAddress, bgpInfoNetwork IpAddress, bgpInfoNextHop DisplayString, bgpInfoMetr DisplayString, bgpInfoLcPrf DisplayString, bgpInfoWght DisplayString, bgpInfoPath DisplayString, bgpInfoOrigin DisplayString, bgpInfoMask DisplayString } bgpInfoIndex OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP router index which is the network address." ::= { bgpInfoRtrTableEntry 1 } bgpInfoNetwork OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP network address." ::= { bgpInfoRtrTableEntry 2 } bgpInfoNextHop OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The BGPs NextHop addresses from a network." ::= { bgpInfoRtrTableEntry 3 } bgpInfoMetr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The BGPs metric from a network." ::= { bgpInfoRtrTableEntry 4 } bgpInfoLcPrf OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The BGPs local preference from a network." ::= { bgpInfoRtrTableEntry 5 } bgpInfoWght OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Total weight of AS paths from a network." ::= { bgpInfoRtrTableEntry 6 } bgpInfoPath OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The AS paths from a network." ::= { bgpInfoRtrTableEntry 7 } bgpInfoOrigin OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The BGPs route origin from a network" ::= { bgpInfoRtrTableEntry 8 } bgpInfoMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The BGP router subnet mask." ::= { bgpInfoRtrTableEntry 9 } -- L3 Operational commands vrrpOperVirtRtrTable OBJECT-TYPE SYNTAX SEQUENCE OF VrrpOperVirtRtrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table of virtual routers." ::= { vrrpOper 1 } vrrpOperVirtRtrEntry OBJECT-TYPE SYNTAX VrrpOperVirtRtrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the vrrpOperVirtRtrTable " INDEX { vrrpOperVirtRtrIndex } ::= { vrrpOperVirtRtrTable 1 } VrrpOperVirtRtrEntry ::= SEQUENCE { vrrpOperVirtRtrIndex Integer32, vrrpOperVirtRtrBackup INTEGER } vrrpOperVirtRtrIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index for the VRRP virtual router." ::= { vrrpOperVirtRtrEntry 1 } vrrpOperVirtRtrBackup OBJECT-TYPE SYNTAX INTEGER { ok(1), backup(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to a value of 'backup(2)' it forces the specified master virtual router into backup mode. 'ok(1)' is returned when the object is read." ::= { vrrpOperVirtRtrEntry 2 } vrrpOperVirtRtrGroupBackup OBJECT-TYPE SYNTAX INTEGER { ok(1), backup(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to a value of 'backup(2)' it forces the specified master virtual router group into backup mode. 'ok(1)' is returned when the object os read." ::= { vrrpOper 2 } -- ---------------------------------------------------------------------------- -- { INSERT: ipsec -- ---------------------------------------------------------------------------- -- ipsecCfg OBJECT IDENTIFIER ::= { layer3Configs 32 } -- ipsecStats OBJECT IDENTIFIER ::= { layer3Stats 24 } -- ipsecInfo OBJECT IDENTIFIER ::= { layer3Info 23 } IPsecKeyString ::= TEXTUAL-CONVENTION DISPLAY-HINT "1024a" STATUS current DESCRIPTION "Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length. " SYNTAX OCTET STRING (SIZE (0..1024)) -- IKEv2 Configuration ikeGroup OBJECT IDENTIFIER ::= { ipsecCfg 1 } ikeCurCfgProposal OBJECT IDENTIFIER ::= { ikeGroup 1 } ikeCurCfgPropCipher OBJECT-TYPE SYNTAX INTEGER { des(1), triple-des(2), aes-cbc(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current encription algorithm used by IKEv2" ::= { ikeCurCfgProposal 1 } ikeCurCfgPropAuth OBJECT-TYPE SYNTAX INTEGER { sha1(1), md5(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current authentication algorithm used by IKEv2" ::= { ikeCurCfgProposal 2 } ikeCurCfgPropGroup OBJECT-TYPE SYNTAX INTEGER { dhGroup1(1), dhGroup2(2), dhGroup5(3), dhGroup14(4), dhGroup24(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current Diffie-Hellman groups used by IKEv2" ::= { ikeCurCfgProposal 3 } ikeNewCfgProposal OBJECT IDENTIFIER ::= { ikeGroup 2 } ikeNewCfgPropCipher OBJECT-TYPE SYNTAX INTEGER { des(1), triple-des(2), aes-cbc(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "New encription algorithm used by IKEv2" ::= { ikeNewCfgProposal 1 } ikeNewCfgPropAuth OBJECT-TYPE SYNTAX INTEGER { sha1(1), md5(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "New authentication algorithm used by IKEv2" ::= { ikeNewCfgProposal 2 } ikeNewCfgPropGroup OBJECT-TYPE SYNTAX INTEGER { dhGroup1(1), dhGroup2(2), dhGroup5(3), dhGroup14(4), dhGroup24(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "New Diffie-Hellman groups used by IKEv2" ::= { ikeNewCfgProposal 3 } ikeCurCfgPsk OBJECT IDENTIFIER ::= { ikeGroup 3 } ikeCurCfgPskLocalKey OBJECT-TYPE SYNTAX IPsecKeyString (SIZE (1..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "Current local pre-shared key." ::= { ikeCurCfgPsk 1 } ikeCurCfgPskRemoteTable OBJECT-TYPE SYNTAX SEQUENCE OF IkeCurCfgPskRemoteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the remote pre-shared key by peer address used by IKEv2." ::= { ikeCurCfgPsk 2 } ikeCurCfgPskRemoteEntry OBJECT-TYPE SYNTAX IkeCurCfgPskRemoteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a remote pre-shared key for a peer address." INDEX { ikeCurCfgPskRemoteIndex } ::= { ikeCurCfgPskRemoteTable 1 } IkeCurCfgPskRemoteEntry ::= SEQUENCE { ikeCurCfgPskRemoteIndex Unsigned32, ikeCurCfgPskRemoteAddr OCTET STRING, ikeCurCfgPskRemoteKey IPsecKeyString, ikeCurCfgPskRemoteDelete INTEGER } ikeCurCfgPskRemoteIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ikeCurCfgPskRemoteTable." ::= { ikeCurCfgPskRemoteEntry 1 } ikeCurCfgPskRemoteAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "Current IPv6 address of peer." ::= { ikeCurCfgPskRemoteEntry 2 } ikeCurCfgPskRemoteKey OBJECT-TYPE SYNTAX IPsecKeyString (SIZE (1..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "Current remote pre-shared key." ::= { ikeCurCfgPskRemoteEntry 3 } ikeCurCfgPskRemoteDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ikeCurCfgPskRemoteEntry 4 } ikeNewCfgPsk OBJECT IDENTIFIER ::= { ikeGroup 4 } ikeNewCfgPskLocalKey OBJECT-TYPE SYNTAX IPsecKeyString (SIZE (1..256)) MAX-ACCESS read-write STATUS current DESCRIPTION "New local pre-shared key." ::= { ikeNewCfgPsk 1 } ikeNewCfgPskRemoteTable OBJECT-TYPE SYNTAX SEQUENCE OF IkeNewCfgPskRemoteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the remote pre-shared key by peer address used by IKEv2." ::= { ikeNewCfgPsk 2 } ikeNewCfgPskRemoteEntry OBJECT-TYPE SYNTAX IkeNewCfgPskRemoteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a remote pre-shared key for a peer address." INDEX { ikeNewCfgPskRemoteIndex } ::= { ikeNewCfgPskRemoteTable 1 } IkeNewCfgPskRemoteEntry ::= SEQUENCE { ikeNewCfgPskRemoteIndex Unsigned32, ikeNewCfgPskRemoteAddr OCTET STRING, ikeNewCfgPskRemoteKey IPsecKeyString, ikeNewCfgPskRemoteDelete INTEGER } ikeNewCfgPskRemoteIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ikeNewCfgPskRemoteTable." ::= { ikeNewCfgPskRemoteEntry 1 } ikeNewCfgPskRemoteAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-create STATUS current DESCRIPTION "New IPv6 address of peer." ::= { ikeNewCfgPskRemoteEntry 2 } ikeNewCfgPskRemoteKey OBJECT-TYPE SYNTAX IPsecKeyString (SIZE (1..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "New remote pre-shared key." ::= { ikeNewCfgPskRemoteEntry 3 } ikeNewCfgPskRemoteDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ikeNewCfgPskRemoteEntry 4 } ikeCurCfgIdentity OBJECT IDENTIFIER ::= { ikeGroup 5 } ikeCurCfgIdType OBJECT-TYPE SYNTAX INTEGER { ipv6-addr(0), fqdn(1), email(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the type of Identification being used." ::= { ikeCurCfgIdentity 1 } ikeCurCfgIdData OBJECT-TYPE SYNTAX DisplayString (SIZE (1..100)) MAX-ACCESS read-only STATUS current DESCRIPTION "Value as indicated by the Identification Type. It can be a fully-qualified domain name string (example.com) or a fully-qualified email address string (jsmith@example.com)." ::= { ikeCurCfgIdentity 2 } ikeNewCfgIdentity OBJECT IDENTIFIER ::= { ikeGroup 6 } ikeNewCfgIdType OBJECT-TYPE SYNTAX INTEGER { ipv6-addr(0), fqdn(1), email(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the type of Identification being used." ::= { ikeNewCfgIdentity 1 } ikeNewCfgIdData OBJECT-TYPE SYNTAX DisplayString (SIZE (1..100)) MAX-ACCESS read-write STATUS current DESCRIPTION "Value as indicated by the Identification Type. It can be a fully-qualified domain name string (example.com) or a fully-qualified email address string (jsmith@example.com)." ::= { ikeNewCfgIdentity 2 } ikeCurCfgTxTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object specify the IKEv2 PDU retransmission timeout in seconds." ::= { ikeGroup 7 } ikeNewCfgTxTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object specify the new IKEv2 PDU retransmission timeout." ::= { ikeGroup 8 } ikeCurCfgCookie OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Globally enable/disable IKEv2 cookie notify." ::= { ikeGroup 9 } ikeNewCfgCookie OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Globally enable/disable IKEv2 cookie notify." ::= { ikeGroup 10 } -- IPsec Configuration ipsecGroup OBJECT IDENTIFIER ::= { ipsecCfg 2 } ipsecCurCfgState OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Globally enable/disable IPsec." ::= { ipsecGroup 1 } ipsecNewCfgState OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Globally enable/disable IPsec." ::= { ipsecGroup 2 } ipsecCurCfgTxformTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecCurCfgTxformEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the IPsec transform-set." ::= { ipsecGroup 3 } ipsecCurCfgTxformEntry OBJECT-TYPE SYNTAX IpsecCurCfgTxformEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec transform-set." INDEX { ipsecCurCfgTxformIndex } ::= { ipsecCurCfgTxformTable 1 } IpsecCurCfgTxformEntry ::= SEQUENCE { ipsecCurCfgTxformIndex Unsigned32, ipsecCurCfgTxformAuth INTEGER, ipsecCurCfgTxformCipher INTEGER, ipsecCurCfgTxformIntegrity INTEGER, ipsecCurCfgTxformMode INTEGER, ipsecCurCfgTxformDelete INTEGER } ipsecCurCfgTxformIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecCurCfgTxformTable." ::= { ipsecCurCfgTxformEntry 1 } ipsecCurCfgTxformAuth OBJECT-TYPE SYNTAX INTEGER { none(0), ah-sha1(1), ah-md5(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The authentication algorithm of the IPsec transform-set" ::= { ipsecCurCfgTxformEntry 2 } ipsecCurCfgTxformCipher OBJECT-TYPE SYNTAX INTEGER { esp-null(0), esp-des(1), esp-3des(2), esp-aes-cbc(3), unspecified(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The encryption algorithm of the IPsec transform-set" ::= { ipsecCurCfgTxformEntry 3 } ipsecCurCfgTxformIntegrity OBJECT-TYPE SYNTAX INTEGER { none(0), esp-sha1(1), esp-md5(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The interity algorithm of the IPsec transform-set" ::= { ipsecCurCfgTxformEntry 4 } ipsecCurCfgTxformMode OBJECT-TYPE SYNTAX INTEGER { transport(1), tunnel(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The tunnel/transport mode of the IPsec transform-set" ::= { ipsecCurCfgTxformEntry 5 } ipsecCurCfgTxformDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ipsecCurCfgTxformEntry 6 } ipsecNewCfgTxformTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecNewCfgTxformEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the new IPsec transform-set to be apply." ::= { ipsecGroup 4 } ipsecNewCfgTxformEntry OBJECT-TYPE SYNTAX IpsecNewCfgTxformEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec transform-set." INDEX { ipsecNewCfgTxformIndex } ::= { ipsecNewCfgTxformTable 1 } IpsecNewCfgTxformEntry ::= SEQUENCE { ipsecNewCfgTxformIndex Unsigned32, ipsecNewCfgTxformAuth INTEGER, ipsecNewCfgTxformCipher INTEGER, ipsecNewCfgTxformIntegrity INTEGER, ipsecNewCfgTxformMode INTEGER, ipsecNewCfgTxformDelete INTEGER } ipsecNewCfgTxformIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecNewCfgTxformTable." ::= { ipsecNewCfgTxformEntry 1 } ipsecNewCfgTxformAuth OBJECT-TYPE SYNTAX INTEGER { none(0), ah-sha1(1), ah-md5(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The authentication algorithm of the IPsec transform-set" ::= { ipsecNewCfgTxformEntry 2 } ipsecNewCfgTxformCipher OBJECT-TYPE SYNTAX INTEGER { esp-null(0), esp-des(1), esp-3des(2), esp-aes-cbc(3), unspecified(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The encryption algorithm of the IPsec transform-set" ::= { ipsecNewCfgTxformEntry 3 } ipsecNewCfgTxformIntegrity OBJECT-TYPE SYNTAX INTEGER { none(0), esp-sha1(1), esp-md5(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The interity algorithm of the IPsec transform-set" ::= { ipsecNewCfgTxformEntry 4 } ipsecNewCfgTxformMode OBJECT-TYPE SYNTAX INTEGER { transport(1), tunnel(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The tunnel/transport mode of the IPsec transform-set" ::= { ipsecNewCfgTxformEntry 5 } ipsecNewCfgTxformDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ipsecNewCfgTxformEntry 6 } ipsecCurCfgSelectorTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecCurCfgSelectorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the IPsec selector." ::= { ipsecGroup 5 } ipsecCurCfgSelectorEntry OBJECT-TYPE SYNTAX IpsecCurCfgSelectorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec selector." INDEX { ipsecCurCfgSelectorIndex } ::= { ipsecCurCfgSelectorTable 1 } IpsecCurCfgSelectorEntry ::= SEQUENCE { ipsecCurCfgSelectorIndex Unsigned32, ipsecCurCfgSelectorAction INTEGER, ipsecCurCfgSelectorProto INTEGER, ipsecCurCfgSelectorIcmpType Unsigned32, ipsecCurCfgSelectorDst OCTET STRING, ipsecCurCfgSelectorDstPrefix Unsigned32, ipsecCurCfgSelectorSrc OCTET STRING, ipsecCurCfgSelectorDelete INTEGER } ipsecCurCfgSelectorIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecCurCfgSelectorTable." ::= { ipsecCurCfgSelectorEntry 1 } ipsecCurCfgSelectorAction OBJECT-TYPE SYNTAX INTEGER { unspecified(0), permit(1), deny(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The action of the IPsec selector" ::= { ipsecCurCfgSelectorEntry 2 } ipsecCurCfgSelectorProto OBJECT-TYPE SYNTAX INTEGER { unspecified(0), tcp(1), icmp(2), any(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol of the IPsec selector" ::= { ipsecCurCfgSelectorEntry 3 } ipsecCurCfgSelectorIcmpType OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "When the protocol of the IPsec selector is icmp(2), This object specify the ICMP type for the traffic selector. 0 = any." ::= { ipsecCurCfgSelectorEntry 4 } ipsecCurCfgSelectorDst OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination ip address of the IPsec selector" ::= { ipsecCurCfgSelectorEntry 6 } ipsecCurCfgSelectorDstPrefix OBJECT-TYPE SYNTAX Unsigned32 (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination ipv6 address prefix length of the IPsec selector" ::= { ipsecCurCfgSelectorEntry 7 } ipsecCurCfgSelectorSrc OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The source ip address of the IPsec selector" ::= { ipsecCurCfgSelectorEntry 8 } ipsecCurCfgSelectorDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ipsecCurCfgSelectorEntry 9 } ipsecNewCfgSelectorTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecNewCfgSelectorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the IPsec selector." ::= { ipsecGroup 6 } ipsecNewCfgSelectorEntry OBJECT-TYPE SYNTAX IpsecNewCfgSelectorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec selector." INDEX { ipsecNewCfgSelectorIndex } ::= { ipsecNewCfgSelectorTable 1 } IpsecNewCfgSelectorEntry ::= SEQUENCE { ipsecNewCfgSelectorIndex Unsigned32, ipsecNewCfgSelectorAction INTEGER, ipsecNewCfgSelectorProto INTEGER, ipsecNewCfgSelectorIcmpType Unsigned32, ipsecNewCfgSelectorDst OCTET STRING, ipsecNewCfgSelectorDstPrefix Unsigned32, ipsecNewCfgSelectorSrc OCTET STRING, ipsecNewCfgSelectorDelete INTEGER } ipsecNewCfgSelectorIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecNewCfgSelectorTable." ::= { ipsecNewCfgSelectorEntry 1 } ipsecNewCfgSelectorAction OBJECT-TYPE SYNTAX INTEGER { unspecified(0), permit(1), deny(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The action of the IPsec selector" ::= { ipsecNewCfgSelectorEntry 2 } ipsecNewCfgSelectorProto OBJECT-TYPE SYNTAX INTEGER { unspecified(0), tcp(1), icmp(2), any(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The protocol of the IPsec selector" ::= { ipsecNewCfgSelectorEntry 3 } ipsecNewCfgSelectorIcmpType OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "When the protocol of the IPsec selector is icmp(2), This object specify the ICMP type for the traffic selector. 0 = any." ::= { ipsecNewCfgSelectorEntry 4 } ipsecNewCfgSelectorDst OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The destination ipv6 address of the IPsec selector" ::= { ipsecNewCfgSelectorEntry 6 } ipsecNewCfgSelectorDstPrefix OBJECT-TYPE SYNTAX Unsigned32 (1..128) MAX-ACCESS read-create STATUS current DESCRIPTION "The destination ipv6 address prefix length of the IPsec selector" ::= { ipsecNewCfgSelectorEntry 7 } ipsecNewCfgSelectorSrc OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The source ip address of the IPsec selector" ::= { ipsecNewCfgSelectorEntry 8 } ipsecNewCfgSelectorDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ipsecNewCfgSelectorEntry 9 } ipsecCurCfgDynamicPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecCurCfgDynamicPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the IPsec dynamic policies." ::= { ipsecGroup 7 } ipsecCurCfgDynamicPolicyEntry OBJECT-TYPE SYNTAX IpsecCurCfgDynamicPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec dynamic policy." INDEX { ipsecCurCfgDynamicPolicyIndex } ::= { ipsecCurCfgDynamicPolicyTable 1 } IpsecCurCfgDynamicPolicyEntry ::= SEQUENCE { ipsecCurCfgDynamicPolicyIndex Unsigned32, ipsecCurCfgDynamicPolicyPeer OCTET STRING, ipsecCurCfgDynamicPolicySelector Unsigned32, ipsecCurCfgDynamicPolicyTxform Unsigned32, ipsecCurCfgDynamicPolicyLifetime Unsigned32, ipsecCurCfgDynamicPolicyPfs INTEGER, ipsecCurCfgDynamicPolicyDelete INTEGER } ipsecCurCfgDynamicPolicyIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecCurCfgDynamicPolicyTable." ::= { ipsecCurCfgDynamicPolicyEntry 1 } ipsecCurCfgDynamicPolicyPeer OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The remote peer ip address." ::= { ipsecCurCfgDynamicPolicyEntry 2 } ipsecCurCfgDynamicPolicySelector OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The traffic selector index for IPsec policy to refer an entry in ipsecCurCfgSelectorTable. 0 = unspecified." ::= { ipsecCurCfgDynamicPolicyEntry 3 } ipsecCurCfgDynamicPolicyTxform OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The transform set index for IPSec policy to refer an entry in ipsecCurCfgTxformTable. 0 = unspecified." ::= { ipsecCurCfgDynamicPolicyEntry 4 } ipsecCurCfgDynamicPolicyLifetime OBJECT-TYPE SYNTAX Unsigned32 (120..86400) MAX-ACCESS read-only STATUS current DESCRIPTION "The SA lifetime for an IPsec policy." ::= { ipsecCurCfgDynamicPolicyEntry 5 } ipsecCurCfgDynamicPolicyPfs OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/disable perfect forward security." ::= { ipsecCurCfgDynamicPolicyEntry 6 } ipsecCurCfgDynamicPolicyDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ipsecCurCfgDynamicPolicyEntry 7 } ipsecNewCfgDynamicPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecNewCfgDynamicPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the IPsec dynamic policies." ::= { ipsecGroup 8 } ipsecNewCfgDynamicPolicyEntry OBJECT-TYPE SYNTAX IpsecNewCfgDynamicPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec dynamic policy." INDEX { ipsecNewCfgDynamicPolicyIndex } ::= { ipsecNewCfgDynamicPolicyTable 1 } IpsecNewCfgDynamicPolicyEntry ::= SEQUENCE { ipsecNewCfgDynamicPolicyIndex Unsigned32, ipsecNewCfgDynamicPolicyPeer OCTET STRING, ipsecNewCfgDynamicPolicySelector Unsigned32, ipsecNewCfgDynamicPolicyTxform Unsigned32, ipsecNewCfgDynamicPolicyLifetime Unsigned32, ipsecNewCfgDynamicPolicyPfs INTEGER, ipsecNewCfgDynamicPolicyDelete INTEGER } ipsecNewCfgDynamicPolicyIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecNewCfgDynamicPolicyTable." ::= { ipsecNewCfgDynamicPolicyEntry 1 } ipsecNewCfgDynamicPolicyPeer OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The remote peer ip address." ::= { ipsecNewCfgDynamicPolicyEntry 2 } ipsecNewCfgDynamicPolicySelector OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "The traffic selector index for IPsec policy to refer an entry in ipsecNewCfgSelectorTable. 0 = unspecified." ::= { ipsecNewCfgDynamicPolicyEntry 3 } ipsecNewCfgDynamicPolicyTxform OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "The transform set index for IPSec policy to refer an entry in ipsecNewCfgTxformTable. 0 = unspecified." ::= { ipsecNewCfgDynamicPolicyEntry 4 } ipsecNewCfgDynamicPolicyLifetime OBJECT-TYPE SYNTAX Unsigned32 (120..86400) MAX-ACCESS read-create STATUS current DESCRIPTION "The SA lifetime for an IPsec policy." ::= { ipsecNewCfgDynamicPolicyEntry 5 } ipsecNewCfgDynamicPolicyPfs OBJECT-TYPE SYNTAX INTEGER { disable(1), enable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable perfect forward security." ::= { ipsecNewCfgDynamicPolicyEntry 6 } ipsecNewCfgDynamicPolicyDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ipsecNewCfgDynamicPolicyEntry 7 } ipsecCurCfgManualPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecCurCfgManualPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the IPsec manual policies." ::= { ipsecGroup 9 } ipsecCurCfgManualPolicyEntry OBJECT-TYPE SYNTAX IpsecCurCfgManualPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec manual policy." INDEX { ipsecCurCfgManualPolicyIndex } ::= { ipsecCurCfgManualPolicyTable 1 } IpsecCurCfgManualPolicyEntry ::= SEQUENCE { ipsecCurCfgManualPolicyIndex Unsigned32, ipsecCurCfgManualPolicyPeer OCTET STRING, ipsecCurCfgManualPolicySelector Unsigned32, ipsecCurCfgManualPolicyTxform Unsigned32, ipsecCurCfgManualPolicyInAhKey OCTET STRING, ipsecCurCfgManualPolicyInAhSpi Unsigned32, ipsecCurCfgManualPolicyOutAhKey OCTET STRING, ipsecCurCfgManualPolicyOutAhSpi Unsigned32, ipsecCurCfgManualPolicyInEspEncKey OCTET STRING, ipsecCurCfgManualPolicyInEspAuthKey OCTET STRING, ipsecCurCfgManualPolicyInEspSpi Unsigned32, ipsecCurCfgManualPolicyOutEspEncKey OCTET STRING, ipsecCurCfgManualPolicyOutEspAuthKey OCTET STRING, ipsecCurCfgManualPolicyOutEspSpi Unsigned32, ipsecCurCfgManualPolicyDelete INTEGER } ipsecCurCfgManualPolicyIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecCurCfgManualPolicyTable." ::= { ipsecCurCfgManualPolicyEntry 1 } ipsecCurCfgManualPolicyPeer OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The remote peer ip address." ::= { ipsecCurCfgManualPolicyEntry 2 } ipsecCurCfgManualPolicySelector OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The traffic selector index for IPsec policy to refer an entry in ipsecCurCfgSelectorTable" ::= { ipsecCurCfgManualPolicyEntry 3 } ipsecCurCfgManualPolicyTxform OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The transform set index for IPSec policy to refer an entry in ipsecCurCfgTxformTable" ::= { ipsecCurCfgManualPolicyEntry 4 } ipsecCurCfgManualPolicyInAhKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The AH inbound session key for an IPsec policy." ::= { ipsecCurCfgManualPolicyEntry 5 } ipsecCurCfgManualPolicyInAhSpi OBJECT-TYPE SYNTAX Unsigned32 (0 | 256..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The AH inbound SPI for an IPsec policy." ::= { ipsecCurCfgManualPolicyEntry 6 } ipsecCurCfgManualPolicyOutAhKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The AH outbound session key for an IPsec policy." ::= { ipsecCurCfgManualPolicyEntry 7 } ipsecCurCfgManualPolicyOutAhSpi OBJECT-TYPE SYNTAX Unsigned32 (0 | 256..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The AH outbound SPI for an IPsec policy." ::= { ipsecCurCfgManualPolicyEntry 8 } ipsecCurCfgManualPolicyInEspEncKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Esp inbound cipher key for an IPsec policy." ::= { ipsecCurCfgManualPolicyEntry 9 } ipsecCurCfgManualPolicyInEspAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Esp inbound authenticator key for an IPsec policy." ::= { ipsecCurCfgManualPolicyEntry 10 } ipsecCurCfgManualPolicyInEspSpi OBJECT-TYPE SYNTAX Unsigned32 (0 | 256..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The Esp inbound SPI for an IPsec policy." ::= { ipsecCurCfgManualPolicyEntry 11 } ipsecCurCfgManualPolicyOutEspEncKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Esp outbound cipher key for an IPsec policy." ::= { ipsecCurCfgManualPolicyEntry 12 } ipsecCurCfgManualPolicyOutEspAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Esp outbound authenticator key for an IPsec policy." ::= { ipsecCurCfgManualPolicyEntry 13 } ipsecCurCfgManualPolicyOutEspSpi OBJECT-TYPE SYNTAX Unsigned32 (0 | 256..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The Esp outbound SPI for an IPsec policy." ::= { ipsecCurCfgManualPolicyEntry 14 } ipsecCurCfgManualPolicyDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ipsecCurCfgManualPolicyEntry 15 } ipsecNewCfgManualPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecNewCfgManualPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the IPsec manual policies." ::= { ipsecGroup 10 } ipsecNewCfgManualPolicyEntry OBJECT-TYPE SYNTAX IpsecNewCfgManualPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec manual policy." INDEX { ipsecNewCfgManualPolicyIndex } ::= { ipsecNewCfgManualPolicyTable 1 } IpsecNewCfgManualPolicyEntry ::= SEQUENCE { ipsecNewCfgManualPolicyIndex Unsigned32, ipsecNewCfgManualPolicyPeer OCTET STRING, ipsecNewCfgManualPolicySelector Unsigned32, ipsecNewCfgManualPolicyTxform Unsigned32, ipsecNewCfgManualPolicyInAhKey OCTET STRING, ipsecNewCfgManualPolicyInAhSpi Unsigned32, ipsecNewCfgManualPolicyOutAhKey OCTET STRING, ipsecNewCfgManualPolicyOutAhSpi Unsigned32, ipsecNewCfgManualPolicyInEspEncKey OCTET STRING, ipsecNewCfgManualPolicyInEspAuthKey OCTET STRING, ipsecNewCfgManualPolicyInEspSpi Unsigned32, ipsecNewCfgManualPolicyOutEspEncKey OCTET STRING, ipsecNewCfgManualPolicyOutEspAuthKey OCTET STRING, ipsecNewCfgManualPolicyOutEspSpi Unsigned32, ipsecNewCfgManualPolicyDelete INTEGER } ipsecNewCfgManualPolicyIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecNewCfgManualPolicyTable." ::= { ipsecNewCfgManualPolicyEntry 1 } ipsecNewCfgManualPolicyPeer OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-create STATUS current DESCRIPTION "The remote peer ip address." ::= { ipsecNewCfgManualPolicyEntry 2 } ipsecNewCfgManualPolicySelector OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "The traffic selector index for IPsec policy to refer an entry in ipsecNewCfgSelectorTable" ::= { ipsecNewCfgManualPolicyEntry 3 } ipsecNewCfgManualPolicyTxform OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "The transform set index for IPSec policy to refer an entry in ipsecNewCfgTxformTable" ::= { ipsecNewCfgManualPolicyEntry 4 } ipsecNewCfgManualPolicyInAhKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "The AH inbound session key for an IPsec policy." ::= { ipsecNewCfgManualPolicyEntry 5 } ipsecNewCfgManualPolicyInAhSpi OBJECT-TYPE SYNTAX Unsigned32 (0 | 256..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The AH inbound SPI for an IPsec policy." ::= { ipsecNewCfgManualPolicyEntry 6 } ipsecNewCfgManualPolicyOutAhKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "The AH outbound session key for an IPsec policy." ::= { ipsecNewCfgManualPolicyEntry 7 } ipsecNewCfgManualPolicyOutAhSpi OBJECT-TYPE SYNTAX Unsigned32 (0 | 256..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The AH outbound SPI for an IPsec policy." ::= { ipsecNewCfgManualPolicyEntry 8 } ipsecNewCfgManualPolicyInEspEncKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Esp inbound cipher key for an IPsec policy." ::= { ipsecNewCfgManualPolicyEntry 9 } ipsecNewCfgManualPolicyInEspAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Esp inbound authenticator key for an IPsec policy." ::= { ipsecNewCfgManualPolicyEntry 10 } ipsecNewCfgManualPolicyInEspSpi OBJECT-TYPE SYNTAX Unsigned32 (0 | 256..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The Esp inbound SPI for an IPsec policy." ::= { ipsecNewCfgManualPolicyEntry 11 } ipsecNewCfgManualPolicyOutEspEncKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Esp outbound cipher key for an IPsec policy." ::= { ipsecNewCfgManualPolicyEntry 12 } ipsecNewCfgManualPolicyOutEspAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Esp outbound authenticator key for an IPsec policy." ::= { ipsecNewCfgManualPolicyEntry 13 } ipsecNewCfgManualPolicyOutEspSpi OBJECT-TYPE SYNTAX Unsigned32 (0 | 256..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The Esp outbound SPI for an IPsec policy." ::= { ipsecNewCfgManualPolicyEntry 14 } ipsecNewCfgManualPolicyDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ipsecNewCfgManualPolicyEntry 15 } ipsecCurCfgIfTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecCurCfgIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of interface IPsec policy configuration." ::= { ipsecGroup 11 } ipsecCurCfgIfEntry OBJECT-TYPE SYNTAX IpsecCurCfgIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of interface IPsec policy configuration." INDEX { ipsecCurCfgIfIndex } ::= { ipsecCurCfgIfTable 1 } IpsecCurCfgIfEntry ::= SEQUENCE { ipsecCurCfgIfIndex Unsigned32, ipsecCurCfgIfDynamicPolicyBmap OCTET STRING, ipsecCurCfgIfManualPolicyBmap OCTET STRING, ipsecCurCfgIfDelete INTEGER } ipsecCurCfgIfIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular interface." ::= { ipsecCurCfgIfEntry 1 } ipsecCurCfgIfDynamicPolicyBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IPsec dynamic policies applied to the IP interface. The policies are presented in bitmap format. This string displays policy number from 1 to 32. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ policy 9 || || || ||___ policy 8 || |____ policy 7 || . . . ||_________ policy 2 |__________ policy 1 where x : 1 - The represented policy applied to the IP interface. 0 - The represented policy not applied to the IP interface." ::= { ipsecCurCfgIfEntry 2 } ipsecCurCfgIfManualPolicyBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "The manual policies applied to the IP interface. The policies are presented in bitmap format. This string displays policy number from 1 to 32. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ policy 9 || || || ||___ policy 8 || |____ policy 7 || . . . ||_________ policy 2 |__________ policy 1 where x : 1 - The represented policy applied to the IP interface. 0 - The represented policy not applied to the IP interface." ::= { ipsecCurCfgIfEntry 5 } ipsecCurCfgIfDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ipsecCurCfgIfEntry 8 } ipsecNewCfgIfTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecNewCfgIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of interface IPsec policy configuration." ::= { ipsecGroup 12 } ipsecNewCfgIfEntry OBJECT-TYPE SYNTAX IpsecNewCfgIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of interface IPsec policy configuration." INDEX { ipsecNewCfgIfIndex } ::= { ipsecNewCfgIfTable 1 } IpsecNewCfgIfEntry ::= SEQUENCE { ipsecNewCfgIfIndex Unsigned32, ipsecNewCfgIfDynamicPolicyBmap OCTET STRING, ipsecNewCfgIfAddDynamicPolicy Unsigned32, ipsecNewCfgIfDelDynamicPolicy Unsigned32, ipsecNewCfgIfManualPolicyBmap OCTET STRING, ipsecNewCfgIfAddManualPolicy Unsigned32, ipsecNewCfgIfDelManualPolicy Unsigned32, ipsecNewCfgIfDelete INTEGER } ipsecNewCfgIfIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular interface." ::= { ipsecNewCfgIfEntry 1 } ipsecNewCfgIfDynamicPolicyBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "The dynamic policies applied to the IP interface. The policies are presented in bitmap format. This string displays policy number from 1 to 32. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ policy 9 || || || ||___ policy 8 || |____ policy 7 || . . . ||_________ policy 2 |__________ policy 1 where x : 1 - The represented policy applied to the IP interface. 0 - The represented policy not applied to the IP interface." ::= { ipsecNewCfgIfEntry 2 } ipsecNewCfgIfAddDynamicPolicy OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "Set the value to a IPsec dynamic policy ID when add the policy to IP interface. A value of 0 is always returned when this object is read." ::= { ipsecNewCfgIfEntry 3 } ipsecNewCfgIfDelDynamicPolicy OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "Set the value to a IPsec dynamic policy ID when delete the policy to IP interface. A value of 0 is always returned when this object is read." ::= { ipsecNewCfgIfEntry 4 } ipsecNewCfgIfManualPolicyBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..4)) MAX-ACCESS read-only STATUS current DESCRIPTION "The manual policies applied to the IP interface. The policies are presented in bitmap format. This string displays policy number from 1 to 32. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ policy 9 || || || ||___ policy 8 || |____ policy 7 || . . . ||_________ policy 2 |__________ policy 1 where x : 1 - The represented policy applied to the IP interface. 0 - The represented policy not applied to the IP interface." ::= { ipsecNewCfgIfEntry 5 } ipsecNewCfgIfAddManualPolicy OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "Set the value to a IPsec manual policy ID when add the policy to IP interface. A value of 0 is always returned when this object is read." ::= { ipsecNewCfgIfEntry 6 } ipsecNewCfgIfDelManualPolicy OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS read-create STATUS current DESCRIPTION "Set the value to a IPsec manual policy ID when delete the policy to IP interface. A value of 0 is always returned when this object is read." ::= { ipsecNewCfgIfEntry 7 } ipsecNewCfgIfDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set a value of delete(2) for this object will delete the entry, A value of other(1) is always returned when this object is read." ::= { ipsecNewCfgIfEntry 8 } -- IPsec Statistics ipsecSaStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecSaStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the IPsec SA statistics." ::= { ipsecStats 1 } ipsecSaStatsEntry OBJECT-TYPE SYNTAX IpsecSaStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec SA statistics." INDEX { ipsecSaStatsIndex } ::= { ipsecSaStatsTable 1 } IpsecSaStatsEntry ::= SEQUENCE { ipsecSaStatsIndex Unsigned32, ipsecSaStatsSpi Unsigned32, ipsecSaStatsProto INTEGER, ipsecSaStatsDstAddr OCTET STRING, ipsecSaStatsUsageTime Unsigned32, ipsecSaStatsBytes Unsigned32, ipsecSaStatsPkts Unsigned32 } ipsecSaStatsIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecSaStatsEntry." ::= { ipsecSaStatsEntry 1 } ipsecSaStatsSpi OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The SPI used by the SA." ::= { ipsecSaStatsEntry 2 } ipsecSaStatsProto OBJECT-TYPE SYNTAX INTEGER { any(0), ah(1), esp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The proto(AH,ESP,or Both) used by the SA." ::= { ipsecSaStatsEntry 3 } ipsecSaStatsDstAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address for the SA." ::= { ipsecSaStatsEntry 4 } ipsecSaStatsUsageTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The time (in seconds) since the SA was first used." ::= { ipsecSaStatsEntry 5 } ipsecSaStatsBytes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of bytes for the SA." ::= { ipsecSaStatsEntry 6 } ipsecSaStatsPkts OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets sent or received for the SA." ::= { ipsecSaStatsEntry 7 } -- IPsec Information ipsecSaInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecSaInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the IPsec SA information." ::= { ipsecInfo 1 } ipsecSaInfoEntry OBJECT-TYPE SYNTAX IpsecSaInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec SA information." INDEX { ipsecSaInfoIndex } ::= { ipsecSaInfoTable 1 } IpsecSaInfoEntry ::= SEQUENCE { ipsecSaInfoIndex Unsigned32, ipsecSaInfoSpi Unsigned32, ipsecSaInfoProto INTEGER, ipsecSaInfoDstAddr OCTET STRING, ipsecSaInfoSrcAddr OCTET STRING, ipsecSaInfoFlags Unsigned32, ipsecSaInfoUlp Unsigned32, ipsecSaInfoMode INTEGER, ipsecSaInfoAuthAlg INTEGER, ipsecSaInfoAuthKey OCTET STRING, ipsecSaInfoEncrAlg INTEGER, ipsecSaInfoEncrKey OCTET STRING } ipsecSaInfoIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecSaInfoEntry." ::= { ipsecSaInfoEntry 1 } ipsecSaInfoSpi OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The SPI used by the SA." ::= { ipsecSaInfoEntry 2 } ipsecSaInfoProto OBJECT-TYPE SYNTAX INTEGER { any(0), ah(51), esp(50) } MAX-ACCESS read-only STATUS current DESCRIPTION "The proto(AH,ESP,or Both) used by the SA." ::= { ipsecSaInfoEntry 3 } ipsecSaInfoDstAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address for the SA." ::= { ipsecSaInfoEntry 4 } ipsecSaInfoSrcAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The source IP address for the SA." ::= { ipsecSaInfoEntry 5 } ipsecSaInfoFlags OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The direction, initiator and etc for an SA; see flag constants below: SA_FLAG_INUSE 0x0001 SA_FLAG_DELETED 0x0002 SA_FLAG_INBOUND 0x0004 SA_FLAG_INITIATOR 0x0008 SA_FLAG_MATURE 0x0010 SA_FLAG_MIRRORED 0x0100 SA_FLAG_IP6 0x0200 SA_FLAG_IKE2 0x0400 SA_FLAG_PFS 0x0800 " ::= { ipsecSaInfoEntry 6 } ipsecSaInfoUlp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The upper layer protocol for an SA; 0=any; see protocol constants below: ICMP 1 IPv4 4 TCP 6 UDP 17 ESP 50 AH 51 IPv6 41 ICMPv6 58 " ::= { ipsecSaInfoEntry 7 } ipsecSaInfoMode OBJECT-TYPE SYNTAX INTEGER { any(0), transport(1), tunnel(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The mode for the SA." ::= { ipsecSaInfoEntry 8 } ipsecSaInfoAuthAlg OBJECT-TYPE SYNTAX INTEGER { any(0), md5(1), sha1(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The authentication algorithm for the SA." ::= { ipsecSaInfoEntry 9 } ipsecSaInfoAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (20..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The authentication key for the SA." ::= { ipsecSaInfoEntry 10 } ipsecSaInfoEncrAlg OBJECT-TYPE SYNTAX INTEGER { any(0), des(1), triple-des(2), blowfish(3), aes(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The encryption algorithm for the SA." ::= { ipsecSaInfoEntry 11 } ipsecSaInfoEncrKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (20..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The encryption key for the SA." ::= { ipsecSaInfoEntry 12 } ipsecSpdInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecSpdInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all of the IPsec security policy information." ::= { ipsecInfo 2 } ipsecSpdInfoEntry OBJECT-TYPE SYNTAX IpsecSpdInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a IPsec security policy information." INDEX { ipsecSpdInfoIndex } ::= { ipsecSpdInfoTable 1 } IpsecSpdInfoEntry ::= SEQUENCE { ipsecSpdInfoIndex Unsigned32, ipsecSpdInfoFlags Unsigned32, ipsecSpdInfoULP Unsigned32, ipsecSpdInfoAction INTEGER, ipsecSpdInfoDstAddr OCTET STRING, ipsecSpdInfoSrcAddr OCTET STRING, ipsecSpdInfoMode INTEGER, ipsecSpdInfoSaSize Unsigned32 } ipsecSpdInfoIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of ipsecSpdInfoEntry." ::= { ipsecSpdInfoEntry 1 } ipsecSpdInfoFlags OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The direction, initiator and etc for an SA; see flag constants below: SP_FLAG_INUSE 0x00000001 SP_FLAG_DELETED 0x00000002 SP_FLAG_INBOUND 0x00000004 SP_FLAG_MIRRORED 0x00000008 SP_FLAG_PFP_LADDR 0x00000100 SP_FLAG_PFP_RADDR 0x00000200 SP_FLAG_PFP_LPORT 0x00000400 SP_FLAG_PFP_RPORT 0x00000800 SP_FLAG_PFP_ULP 0x00001000 SP_MASK_PFP 0x00001f00 SP_FLAG_DF 0x00002000 SP_FLAG_DF_BIT 0x00004000 SP_MASK_DF 0x00006000 SP_FLAG_DSCP 0x00008000 SP_FLAG_ECN 0x00010000 SP_FLAG_IP6 0x00000010 SP_FLAG_IP6_TUNNEL 0x00000020 SP_FLAG_INIT 0x00000040 " ::= { ipsecSpdInfoEntry 2 } ipsecSpdInfoULP OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The transport layer protocol for the SA. 0 = any. see protocol constants below: ICMP 1 IPv4 4 TCP 6 UDP 17 ESP 50 AH 51 IPv6 41 ICMPv6 58 " ::= { ipsecSpdInfoEntry 3 } ipsecSpdInfoAction OBJECT-TYPE SYNTAX INTEGER { drop(1), apply(2), permit(3), bypass(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The IPsec action for the SA." ::= { ipsecSpdInfoEntry 4 } ipsecSpdInfoDstAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address for the SA." ::= { ipsecSpdInfoEntry 5 } ipsecSpdInfoSrcAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The source IP address for the SA." ::= { ipsecSpdInfoEntry 6 } ipsecSpdInfoMode OBJECT-TYPE SYNTAX INTEGER { any(0), transport(1), tunnel(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The mode for the SA." ::= { ipsecSpdInfoEntry 7 } ipsecSpdInfoSaSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The SA bundle size of an Security policy." ::= { ipsecSpdInfoEntry 8 } ipsecSpdInfoSaTable OBJECT-TYPE SYNTAX SEQUENCE OF IpsecSpdInfoSaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing all information of the SA nested in an IPsec security policy." ::= { ipsecInfo 3 } ipsecSpdInfoSaEntry OBJECT-TYPE SYNTAX IpsecSpdInfoSaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) representing a SA information netsted in an IPsec security policy." INDEX { ipsecSpdInfoIndex, ipsecSpdInfoSaIndex } ::= { ipsecSpdInfoSaTable 1 } IpsecSpdInfoSaEntry ::= SEQUENCE { ipsecSpdInfoSaIndex Unsigned32, ipsecSpdInfoSaSecuProto INTEGER, ipsecSpdInfoSaAuthAlg INTEGER, ipsecSpdInfoSaEncrAlg INTEGER, ipsecSpdInfoSaEncrKeyLen Unsigned32 } ipsecSpdInfoSaIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index that enumerates the IPsec nested SAs ." ::= { ipsecSpdInfoSaEntry 1 } ipsecSpdInfoSaSecuProto OBJECT-TYPE SYNTAX INTEGER { ah(0), esp(1), esp-auth(2), esp-null(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The security protocol for the SA." ::= { ipsecSpdInfoSaEntry 2 } ipsecSpdInfoSaAuthAlg OBJECT-TYPE SYNTAX INTEGER { any(0), md5(1), sha1(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The hash algorithm used by the SA." ::= { ipsecSpdInfoSaEntry 3 } ipsecSpdInfoSaEncrAlg OBJECT-TYPE SYNTAX INTEGER { any(0), des(1), triple-des(2), blowfish(3), aes(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The encryption algorithm used by the SA." ::= { ipsecSpdInfoSaEntry 4 } ipsecSpdInfoSaEncrKeyLen OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The encryption key length of an nested SA." ::= { ipsecSpdInfoSaEntry 5 } -- ---------------------------------------------------------------------------- -- } INSERT: layer3 -- ---------------------------------------------------------------------------- traps OBJECT IDENTIFIER ::= { g8052-mgmt 7 } -- ---------------------------------------------------------------------------- -- { INSERT: traps -- ---------------------------------------------------------------------------- -- SECTION 2: Temporary Object Definitions Used In traps swTrapDisplayString OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "Temporary string object used to store information being sent in a Switch trap." ::= { traps 1000 } -- SECTION 3: Trap Definitions -- Many of the following traps include sysName, sysLocation and sysContact. -- These variables are all defined in the rfc1213 MIB. -- -- sysName is the administratively-assigned name for this managed node. By -- convention, this is the node's fully-qualified domain name. -- -- sysLocation is the physical location of this node (e.g., 'telephone closet, -- 3rd floor'). -- -- sysContact is textual identification of the contact person for this managed -- node, together with information on how to contact this person. -- -- SNMP v3 traps should be defined here. -- ibmSNMPv2Notifications OBJECT IDENTIFIER ::= { traps 0 } swPrimaryPowerSupplyFailureNotify NOTIFICATION-TYPE OBJECTS { swTrapDisplayString, sysName, sysLocation, sysContact } STATUS current DESCRIPTION "A swPrimaryPowerSupplyFailure trap signifies that the primary power supply failed." ::= { ibmSNMPv2Notifications 1 } swPrimaryPowerSupplyFixedNotify NOTIFICATION-TYPE OBJECTS { swTrapDisplayString, sysName, sysLocation, sysContact } STATUS current DESCRIPTION "A swPrimaryPowerSupplyFixed trap signifies that the primary power supply has been restored." ::= { ibmSNMPv2Notifications 97 } -- -- SNMP v1 traps should be defined here. -- swPrimaryPowerSupplyFailure TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swPrimaryPowerSupplyFailure trap signifies that the primary power supply failed." --#SEVERITY CRITICAL ::= 1 -- 0x01 swDefGwUp TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, ipCurCfgGwIndex, ipCurCfgGwAddr, sysName, sysLocation, sysContact } DESCRIPTION "A swDefGwUp trap signifies that the default gateway is alive. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for ipCurCfgGwIndex is from 1 to ipGatewayTableMax. ipCurCfgGwAddr is the IP address of the default gateway." ::= 2 -- 0x02 swDefGwDown TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, ipCurCfgGwIndex, ipCurCfgGwAddr, sysName, sysLocation, sysContact } DESCRIPTION "A swDefGwDown trap signifies that the default gateway is down. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for ipCurCfgGwIndex is from 1 to ipGatewayTableMax. ipCurCfgGwAddr is the IP address of the default gateway." ::= 3 -- 0x03 swDefGwInService TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, ipCurCfgGwIndex, ipCurCfgGwAddr, sysName, sysLocation, sysContact } DESCRIPTION "A swDefGwInService trap signifies that the default gateway is up and in service. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for ipCurCfgGwIndex is from 1 to ipGatewayTableMax. ipCurCfgGwAddr is the IP address of the default gateway." ::= 4 -- 0x04 swDefGwNotInService TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, ipCurCfgGwIndex, ipCurCfgGwAddr, sysName, sysLocation, sysContact } DESCRIPTION "A swDefGwNotInService trap signifies that the default gateway is alive but not in service. ipCurCfgGwIndex is the index of the Gateway in ipCurCfgGwTable. The range for ipCurCfgGwIndex is from 1 to ipGatewayTableMax. ipCurCfgGwAddr is the IP address of the default gateway." ::= 5 -- 0x05 swLoginFailure TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swLoginFailure trap signifies that someone failed to enter a valid username/password combination. swTrapDisplayString specifies whether the login attempt was from CONSOLE or TELNET. In case of TELNET login it also specifies the IP address of the host from which the attempt was made." ::= 19 -- 0x13 swTempExceedThreshold TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swTempExceedThreshold trap signifies that the switch temperature has exceeded maximum safety limits." ::= 22 -- 0x16 swFanFailure TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swFanFailure trap signifies that the fan failure has been detected." ::= 24 -- 0x18 swValidLogin TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swValidLogin trap signifies that a user login has occured." ::= 25 -- 0x19 swApplyComplete TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swApplyComplete signifies that new configuration has been applied." ::= 27 -- 0x1B swSaveComplete TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swApplyComplete signifies that new configuration has been saved." ::= 28 -- 0x1C swFwDownloadSucess TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swFwDownloadSuccess signifies that firmware has been downloaded to [image1|image2|boot image]." ::= 29 -- 0x1D swFwDownloadFailure TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swFwDownloadFailure signifies that firmware downloaded failed to [image1|image2|boot image]." ::= 30 -- 0x1E swFanFailureFixed TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swFanFailureFixed trap signifies that the fan failure has been fixed." ::= 33 -- 0x21 swStgNewRoot TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, stgCurCfgIndex, sysName, sysLocation, sysContact } DESCRIPTION "A swStgNewRoot trap signifies that the bridge has become the new root of the STG." --#SEVERITY INFORMATIONAL ::= 42 -- 0x2A swCistNewRoot TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swCistNewRoot trap signifies that the bridge has become the new root of the CIST." --#SEVERITY INFORMATIONAL ::= 43 -- 0x2B swStgTopologyChanged TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, stgCurCfgIndex, sysName, sysLocation, sysContact } DESCRIPTION "A swStgTopologyChanged trap signifies that there was a STG topology change." --#SEVERITY INFORMATIONAL ::= 44 -- 0x2C swCistTopologyChanged TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swCistTopologyChanged trap signifies that there was a CIST topology change." --#SEVERITY INFORMATIONAL ::= 45 -- 0x2D swHotlinksMasterUp TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swHotlinksMasterUp trap signifies that the Master interface is active." ::= 46 -- 0x2E swHotlinksMasterDn TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swHotlinksMasterDn trap signifies that the Master interface is not active." ::= 47 -- 0x2F swHotlinksBackupUp TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swHotlinksBackupUp trap signifies that the Backup interface is active." ::= 48 -- 0x30 swHotlinksBackupDn TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swHotlinksBackupDn trap signifies that the Backup interface is not active." ::= 49 -- 0x31 swHotlinksNone TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swHotlinksNone trap signifies that there are no active interfaces." ::= 50 -- 0x32 sfpInserted TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, ifIndex, sysName, sysLocation, sysContact } DESCRIPTION "A sfpInserted trap signifies that a SFP is inserted." --#SEVERITY INFORMATIONAL ::= 51 -- 0x33 sfpRemoved TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, ifIndex, sysName, sysLocation, sysContact } DESCRIPTION "A sfpRemoved trap signifies that a SFP is removed." --#SEVERITY INFORMATIONAL ::= 52 -- 0x34 swNTPSyncFailed TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swNTPSyncFailed trap signifies that sync with NTP server failed." ::= 61 -- 0x3D swNTPUpdateClock TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swNTPUpdateClock trap signifies that update system clock with NTP server." ::= 62 -- 0x3E swValidLogout TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swValidLogout trap signifies that a user logout has occured." ::= 63 -- 0x3F swECMPGatewayUp TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swECMPGatewayUp trap signifies that the ECMP gateway is up." --#SEVERITY INFORMATIONAL ::= 65 -- 0x41 swECMPGatewayDown TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swECMPGatewayDown trap signifies that the ECMP gateway is down." --#SEVERITY INFORMATIONAL ::= 66 -- 0x42 swTeamingCtrlUp TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swTeamingCtrlUp trap signifies that the teaming is up." --#SEVERITY INFORMATIONAL ::= 67 -- 0x43 swTeamingCtrlDown TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swTeamingCtrlDown trap signifies that the teaming control is down." --#SEVERITY INFORMATIONAL ::= 68 -- 0x44 swTeamingCtrlDownTearDownBlked TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swTeamingCtrlDownTearDownBlked trap signifies that the teaming control is down but teardown is blocked." --#SEVERITY INFORMATIONAL ::= 69 -- 0x45 swTeamingCtrlError TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swTeamingCtrlError trap signifies error, action is undefined." --#SEVERITY INFORMATIONAL ::= 70 -- 0x46 swTempReturnThreshold TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swTempReturnThreshold trap signifies that the switch temperature has returned below maximum safety limits." --#SEVERITY INFORMATIONAL ::= 31 -- 0x1F swLACPPortBlocked TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swLACPPortBlocked trap signifies that LACP is operationally down on a port, and traffic is blocked on the port." --#SEVERITY INFORMATIONAL ::= 71 -- 0x47 swLACPPortUnblocked TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swLACPPortUnblocked trap signifies that LACP is operationally up on a port, and traffic is no longer blocked on the port." --#SEVERITY INFORMATIONAL ::= 72 -- 0x48 swVMGroupVMotion TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A altVMGroupVMotion trap signifies that a virtual machine has moved from a port to another." --#SEVERITY INFORMATIONAL ::= 77 -- 0x4D swVMGroupVMOnline TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A altVMGroupVMOnline trap signifies that a advance provisioned virtual machine has came online." --#SEVERITY INFORMATIONAL ::= 78 -- 0x4E swVMGroupVMVlanChange TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A altVMGroupVMVlanChange trap signifies that a virtual machine has entered into a vlan, or changed the vlan." --#SEVERITY INFORMATIONAL ::= 79 -- 0x4F swPrimaryPowerSupplyFixed TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swPrimaryPowerSupplyFixed trap signifies that the primary power supply has been restored." --#SEVERITY CRITICAL ::= 97 -- 0x61 swLFDPortErrdisabled TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "An swLFDPortErrdisabled trap signifies that a port is error-disabled due to excessive link flaps." --#SEVERITY INFORMATIONAL ::= 103 -- 0x67 swVlagInstanceUp TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swVlagInstanceUp trap signifies that vLAG instance is up identified in the trap message." --#SEVERITY INFORMATIONAL ::= 106 -- 0x6A swVlagInstanceRemoteUp TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swVlagInstanceRemoteUp trap signifies that vLAG is down but remote instance is Up." --#SEVERITY INFORMATIONAL ::= 107 -- 0x6B swVlagInstanceLocalUp TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swVlagInstanceLocalUp trap signifies that vLAG is down but local instance is Up." --#SEVERITY INFORMATIONAL ::= 108 -- 0x6C swVlagInstanceDown TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swVlagInstanceDown trap signifies that vLAG instance is down identified in the trap message." --#SEVERITY INFORMATIONAL ::= 109 -- 0x6D swVlagIslUp TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swVlagIslUp trap signifies that connection between vLAG switches is up." --#SEVERITY INFORMATIONAL ::= 110 -- 0x6E swVlagIslDown TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swVlagInstanceDown trap signifies that connection between vLAG switches is down." --#SEVERITY INFORMATIONAL ::= 111 -- 0x6F swOflowConnectControllerFailure TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowConnectControllerFailure trap signifies that the connection to openflow controller is broken." --#SEVERITY CRITICAL ::= 144 -- 0x90 swOflowConnectControllerSuccess TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowConnectControllerSuccess trap signifies that the connection to openflow controller is successful." --#SEVERITY INFORMATIONAL ::= 145 -- 0x91 swOflowEmergencyState TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowEmergencyState trap signifies that the openflow switch moving to emergency state." --#SEVERITY CRITICAL ::= 146 -- 0x92 swOflowNoEmergencyState TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowNoEmergencyState trap signifies that the openflow switch came out of emergency state." --#SEVERITY INFORMATIONAL ::= 147 -- 0x93 swOflowSwitchOflowMode TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowSwitchOflowMode trap signifies that the device working in openflow switch mode." --#SEVERITY INFORMATIONAL ::= 148 -- 0x94 swOflowSwitcNormalMode TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowSwitcNormalMode trap signifies that the device working in normal switch mode." --#SEVERITY INFORMATIONAL ::= 149 -- 0x95 swOflowSwitcFlowtableClr TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowSwitcFlowtableClr trap signifies that the flow table entries being cleared from the device." --#SEVERITY INFORMATIONAL ::= 150 -- 0x96 swOflowSwitcStatsClr TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowSwitcStatsClr trap signifies that the openflow statistics being cleared from the device." --#SEVERITY INFORMATIONAL ::= 151 -- 0x97 swOflowFlowtableEntryUnavail TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowFlowtableMemoryUnavail trap signifies that the device unable to add flow entry in openflow due to unavailability of system resources." --#SEVERITY INFORMATIONAL ::= 152 -- 0x98 swOflowFlowtableLimit TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowFlowtableLimit trap signifies that the device reaches its configured flow limit." --#SEVERITY INFORMATIONAL ::= 153 -- 0x99 swOflowPortDownController TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowPortDownController trap signifies that the port operationally down by openflow controller." --#SEVERITY INFORMATIONAL ::= 154 -- 0x9a swOflowPortUpController TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowPortUpController trap signifies that the port operationally up by openflow controller." --#SEVERITY INFORMATIONAL ::= 155 -- 0x9b swOflowVersionNegotiationError TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swOflowVersionNegotiationError trap signifies that the device unable to connect to controller either due to bad version, or negotiation/hello failure." --#SEVERITY INFORMATIONAL ::= 156 -- 0x9c sw8021x TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A sw8021x trap is sent when dot1x feature is enabled." ::= 158 -- 0x9F swDefAdminDisable TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swDefAdminDisable trap signifies that default admin account has been disabled." ::= 162 -- 0xA2 swAcntStrngPswdNotMet TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swAcntStrngPswdNotMet trap signifies that configured password does not match strong password complexity." ::= 163 -- 0xA3 swAcntLocked TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swAcntLocked trap signifies that account has been locked." ::= 164 -- 0xA4 swAcntUnlocked TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swAcntUnlocked trap signifies that account has been unlocked." ::= 165 -- 0xA5 swARPtablefull TRAP-TYPE ENTERPRISE traps VARIABLES { swTrapDisplayString, sysName, sysLocation, sysContact } DESCRIPTION "A swARPtablefull trap signifies that ARP table is full." ::= 184 -- 0xB8 -- ---------------------------------------------------------------------------- -- ---------------------------------------------------------------------------- -- } INSERT: traps -- ---------------------------------------------------------------------------- qos OBJECT IDENTIFIER ::= { g8052-mgmt 8 } -- ---------------------------------------------------------------------------- -- { INSERT: qos -- ---------------------------------------------------------------------------- qosConfig OBJECT IDENTIFIER ::= { qos 1 } --Only show these objects when we have it in the CLI --qosStats OBJECT IDENTIFIER ::= { qos 2 } --qosInfo OBJECT IDENTIFIER ::= { qos 3 } --qosOper OBJECT IDENTIFIER ::= { qos 4 } qos8021p OBJECT IDENTIFIER ::= { qosConfig 1 } qosdscp OBJECT IDENTIFIER ::= { qosConfig 2 } qoswredecn OBJECT IDENTIFIER ::= { qosConfig 3 } -- QOS Configuration qosCurCfgPortPriorityTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSCurCfgPortPriorityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of QOS Port Priority configuration." ::= { qos8021p 1 } qosCurCfgPortPriorityEntry OBJECT-TYPE SYNTAX QoSCurCfgPortPriorityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular QOS Port Priority configuration." INDEX { qosCurCfgPortIndex } ::= { qosCurCfgPortPriorityTable 1 } QoSCurCfgPortPriorityEntry ::= SEQUENCE { qosCurCfgPortIndex PortNumber, qosCurCfgPortPriority INTEGER } qosCurCfgPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Switch Port Number" ::= { qosCurCfgPortPriorityEntry 1 } qosCurCfgPortPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Switch Port Priority Should be between 0 and 7" ::= { qosCurCfgPortPriorityEntry 2 } qosNewCfgPortPriorityTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSNewCfgPortPriorityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of QOS Port Priority configuration." ::= { qos8021p 2 } qosNewCfgPortPriorityEntry OBJECT-TYPE SYNTAX QoSNewCfgPortPriorityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular QOS Port Priority configuration." INDEX { qosNewCfgPortIndex } ::= { qosNewCfgPortPriorityTable 1 } QoSNewCfgPortPriorityEntry ::= SEQUENCE { qosNewCfgPortIndex PortNumber, qosNewCfgPortPriority INTEGER } qosNewCfgPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Switch Port Number" ::= { qosNewCfgPortPriorityEntry 1 } qosNewCfgPortPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Switch Port Priority Should be between 0 and 7" ::= { qosNewCfgPortPriorityEntry 2 } qosCurCfgPriorityCoSTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSCurCfgPriorityCoSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Frame Priority and COSq configuration." ::= { qos8021p 3 } qosCurCfgPriorityCoSEntry OBJECT-TYPE SYNTAX QoSCurCfgPriorityCoSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Frame Priority and COSq configuration." INDEX { qosCurCfgPriorityIndex } ::= { qosCurCfgPriorityCoSTable 1 } QoSCurCfgPriorityCoSEntry ::= SEQUENCE { qosCurCfgPriorityIndex INTEGER, qosCurCfgPriorityCoSq INTEGER } qosCurCfgPriorityIndex OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Frame priority Number" ::= { qosCurCfgPriorityCoSEntry 1 } qosCurCfgPriorityCoSq OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "CoSq for a Frame Priority Should be between 0 and 7" ::= { qosCurCfgPriorityCoSEntry 2 } qosNewCfgPriorityCoSTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSNewCfgPriorityCoSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Frame Priority and COSq configuration." ::= { qos8021p 4 } qosNewCfgPriorityCoSEntry OBJECT-TYPE SYNTAX QoSNewCfgPriorityCoSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Frame Priority and COSq configuration." INDEX { qosNewCfgPriorityIndex } ::= { qosNewCfgPriorityCoSTable 1 } QoSNewCfgPriorityCoSEntry ::= SEQUENCE { qosNewCfgPriorityIndex INTEGER, qosNewCfgPriorityCoSq INTEGER } qosNewCfgPriorityIndex OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Frame priority Number" ::= { qosNewCfgPriorityCoSEntry 1 } qosNewCfgPriorityCoSq OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "CoSq for a Frame Priority Should be between 0 and 7" ::= { qosNewCfgPriorityCoSEntry 2 } qosCurCfgCosWeightTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSCurCfgCosWeightEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of CoSq and Weight configuration." ::= { qos8021p 5 } qosCurCfgCosWeightEntry OBJECT-TYPE SYNTAX QoSCurCfgCosWeightEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular CoSq and Weight configuration." INDEX { qosCurCfgCosIndex } ::= { qosCurCfgCosWeightTable 1 } QoSCurCfgCosWeightEntry ::= SEQUENCE { qosCurCfgCosIndex INTEGER, qosCurCfgCosWeight INTEGER } qosCurCfgCosIndex OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "CoSq Number" ::= { qosCurCfgCosWeightEntry 1 } qosCurCfgCosWeight OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "Weight of CoSq" ::= { qosCurCfgCosWeightEntry 2 } qosNewCfgCosWeightTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSNewCfgCosWeightEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of CoSq and Weight configuration." ::= { qos8021p 6 } qosNewCfgCosWeightEntry OBJECT-TYPE SYNTAX QoSNewCfgCosWeightEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular CoSq and Weight configuration." INDEX { qosNewCfgCosIndex } ::= { qosNewCfgCosWeightTable 1 } QoSNewCfgCosWeightEntry ::= SEQUENCE { qosNewCfgCosIndex INTEGER, qosNewCfgCosWeight INTEGER } qosNewCfgCosIndex OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "CoSq Number" ::= { qosNewCfgCosWeightEntry 1 } qosNewCfgCosWeight OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-write STATUS current DESCRIPTION "Weight of CoSq" ::= { qosNewCfgCosWeightEntry 2 } qosCurCfgCosNum OBJECT-TYPE SYNTAX INTEGER { num2(2), num8(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Number of CoSq." ::= { qos8021p 7 } qosNewCfgCosNum OBJECT-TYPE SYNTAX INTEGER { num2(2), num8(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "Number of CoSq." ::= { qos8021p 8 } qosDefaultCfg OBJECT-TYPE SYNTAX INTEGER { none(0), defaultCosNum(1), defaultWeight(2), defaultPriority(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Load default configuration." ::= { qos8021p 9 } qosCurCfgDscpTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSCurCfgDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Dscp to New Dscp/802.1p priority configuration." ::= { qosdscp 1 } qosCurCfgDscpEntry OBJECT-TYPE SYNTAX QoSCurCfgDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Dscp to New Dscp/802.1p priority configuration" INDEX { qosCurCfgDscpIndex } ::= { qosCurCfgDscpTable 1 } QoSCurCfgDscpEntry ::= SEQUENCE { qosCurCfgDscpIndex INTEGER, qosCurCfgMapDscp INTEGER ,qosCurCfgMap8021p INTEGER } qosCurCfgDscpIndex OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Dscp value" ::= { qosCurCfgDscpEntry 1 } qosCurCfgMapDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Map Dscp Value" ::= { qosCurCfgDscpEntry 2 } qosCurCfgMap8021p OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Map 802.1p value" ::= { qosCurCfgDscpEntry 3 } qosNewCfgDscpTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSNewCfgDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Dscp to New Dscp/802.1p priority configuration." ::= { qosdscp 2 } qosNewCfgDscpEntry OBJECT-TYPE SYNTAX QoSNewCfgDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Dscp to New Dscp/802.1p priority configuration" INDEX { qosNewCfgDscpIndex } ::= { qosNewCfgDscpTable 1 } QoSNewCfgDscpEntry ::= SEQUENCE { qosNewCfgDscpIndex INTEGER, qosNewCfgMapDscp INTEGER ,qosNewCfgMap8021p INTEGER } qosNewCfgDscpIndex OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Dscp value" ::= { qosNewCfgDscpEntry 1 } qosNewCfgMapDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Map Dscp Value" ::= { qosNewCfgDscpEntry 2 } qosNewCfgMap8021p OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Map 802.1p value" ::= { qosNewCfgDscpEntry 3 } qosCurCfgDscpState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is for turning on/off DSCP globally." ::= { qosdscp 3 } qosNewCfgDscpState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is for turning on/off DSCP globally." ::= { qosdscp 4 } -- WRED ECN Configuration -- cur port profile table qosCurCfgPortProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSCurCfgPortProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of QOS port WRED ECN profile configuration." ::= { qoswredecn 1 } qoSCurCfgPortProfileEntry OBJECT-TYPE SYNTAX QoSCurCfgPortProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Transmit queue of a port WRED ECN profile configuration." INDEX { qosCurCfgProfilePortIndex , qosCurCfgTrqIndex} ::= { qosCurCfgPortProfileTable 1 } QoSCurCfgPortProfileEntry ::= SEQUENCE { qosCurCfgProfilePortIndex PortNumber, qosCurCfgTrqIndex INTEGER, qosCurCfgTrqNonTcpMin INTEGER, qosCurCfgTrqNonTcpMax INTEGER, qosCurCfgTrqNonTcpRate INTEGER, qosCurCfgTrqTcpMin INTEGER, qosCurCfgTrqTcpMax INTEGER, qosCurCfgTrqTcpRate INTEGER, qosCurCfgPortTrqWredState INTEGER } qosCurCfgProfilePortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Switch Port Number" ::= { qoSCurCfgPortProfileEntry 1 } qosCurCfgTrqIndex OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit Queue Number" ::= { qoSCurCfgPortProfileEntry 2 } qosCurCfgTrqNonTcpMin OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Port Transmit queue WRED ECN nontcp profile MinThreshold value." ::= { qoSCurCfgPortProfileEntry 3 } qosCurCfgTrqNonTcpMax OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Port Transmit queue WRED ECN nontcp profile MaxThreshold value" ::= { qoSCurCfgPortProfileEntry 4 } qosCurCfgTrqNonTcpRate OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Port Transmit queue WRED ECN nontcp profile DropRate value." ::= { qoSCurCfgPortProfileEntry 5 } qosCurCfgTrqTcpMin OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Port Transmit queue WRED ECN tcp profile MinThreshold value." ::= { qoSCurCfgPortProfileEntry 6 } qosCurCfgTrqTcpMax OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Port Transmit queue WRED ECN tcp profile MaxThreshold value" ::= { qoSCurCfgPortProfileEntry 7 } qosCurCfgTrqTcpRate OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Port Transmit queue WRED ECN tcp profile DropRate value." ::= { qoSCurCfgPortProfileEntry 8 } qosCurCfgPortTrqWredState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is for turning on/off WRED per transmit queue per port." ::= { qoSCurCfgPortProfileEntry 9 } -- new port profile table qosNewCfgPortProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSNewCfgPortProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of QOS Port WRED ECN configuration." ::= { qoswredecn 2 } qoSNewCfgPortProfileEntry OBJECT-TYPE SYNTAX QoSNewCfgPortProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Transmit queue of a port WRED ECN configuration." INDEX { qosNewCfgProfilePortIndex , qosNewCfgTrqIndex} ::= { qosNewCfgPortProfileTable 1 } QoSNewCfgPortProfileEntry ::= SEQUENCE { qosNewCfgProfilePortIndex PortNumber, qosNewCfgTrqIndex INTEGER, qosNewCfgTrqNonTcpMin INTEGER, qosNewCfgTrqNonTcpMax INTEGER, qosNewCfgTrqNonTcpRate INTEGER, qosNewCfgTrqTcpMin INTEGER, qosNewCfgTrqTcpMax INTEGER, qosNewCfgTrqTcpRate INTEGER, qosNewCfgPortTrqWredState INTEGER } qosNewCfgProfilePortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Switch Port Number" ::= { qoSNewCfgPortProfileEntry 1 } qosNewCfgTrqIndex OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Transmit Queue Number" ::= { qoSNewCfgPortProfileEntry 2 } qosNewCfgTrqNonTcpMin OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Port Transmit queue WRED ECN nontcp profile MinThreshold value." ::= { qoSNewCfgPortProfileEntry 3 } qosNewCfgTrqNonTcpMax OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Port Transmit queue WRED ECN nontcp profile MaxThreshold value." ::= { qoSNewCfgPortProfileEntry 4 } qosNewCfgTrqNonTcpRate OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Port Transmit queue WRED ECN nontcp profile DropRate value." ::= { qoSNewCfgPortProfileEntry 5 } qosNewCfgTrqTcpMin OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Port Transmit queue WRED ECN tcp profile MinThreshold value." ::= { qoSNewCfgPortProfileEntry 6 } qosNewCfgTrqTcpMax OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Port Transmit queue WRED ECN tcp profile MaxThreshold value." ::= { qoSNewCfgPortProfileEntry 7 } qosNewCfgTrqTcpRate OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Port Transmit queue WRED ECN tcp profile DropRate value." ::= { qoSNewCfgPortProfileEntry 8 } qosNewCfgPortTrqWredState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is for turning on/off WRED per transmit queue per port." ::= { qoSNewCfgPortProfileEntry 9 } -- cur port wred ecn state qosCurCfgPortStateTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSCurCfgPortStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of QOS port WRED ECN state configuration." ::= { qoswredecn 3 } qoSCurCfgPortStateEntry OBJECT-TYPE SYNTAX QoSCurCfgPortStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular port WRED ECN state configuration." INDEX { qosCurCfgStatePortIndex } ::= { qosCurCfgPortStateTable 1 } QoSCurCfgPortStateEntry ::= SEQUENCE { qosCurCfgStatePortIndex PortNumber, qosCurCfgPortWredState INTEGER, qosCurCfgPortEcnState INTEGER } qosCurCfgStatePortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Switch Port Number" ::= { qoSCurCfgPortStateEntry 1 } qosCurCfgPortWredState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is for turning on/off WRED per port." ::= { qoSCurCfgPortStateEntry 2 } qosCurCfgPortEcnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is for turning on/off ECN per port." ::= { qoSCurCfgPortStateEntry 3 } -- new port wred ecn state qosNewCfgPortStateTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSNewCfgPortStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of QOS port WRED ECN state configuration." ::= { qoswredecn 4 } qoSNewCfgPortStateEntry OBJECT-TYPE SYNTAX QoSNewCfgPortStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular port WRED ECN state configuration." INDEX { qosNewCfgStatePortIndex } ::= { qosNewCfgPortStateTable 1 } QoSNewCfgPortStateEntry ::= SEQUENCE { qosNewCfgStatePortIndex PortNumber, qosNewCfgPortWredState INTEGER, qosNewCfgPortEcnState INTEGER } qosNewCfgStatePortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "Switch Port Number" ::= { qoSNewCfgPortStateEntry 1 } qosNewCfgPortWredState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is for turning on/off WRED per port" ::= { qoSNewCfgPortStateEntry 2 } qosNewCfgPortEcnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is for turning on/off ECN per port." ::= { qoSNewCfgPortStateEntry 3 } -- global cur profile config qosCurCfgGlobalProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSCurCfgGlobalProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of QOS global WRED ECN profile configuration." ::= { qoswredecn 5 } qoSCurCfgGlobalProfileEntry OBJECT-TYPE SYNTAX QoSCurCfgGlobalProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Transmit queue of global WRED ECN profile configuration." INDEX { qosCurCfgGlobalTrqIndex} ::= { qosCurCfgGlobalProfileTable 1 } QoSCurCfgGlobalProfileEntry ::= SEQUENCE { qosCurCfgGlobalTrqIndex INTEGER, qosCurCfgGlobalTrqNonTcpMin INTEGER, qosCurCfgGlobalTrqNonTcpMax INTEGER, qosCurCfgGlobalTrqNonTcpRate INTEGER, qosCurCfgGlobalTrqTcpMin INTEGER, qosCurCfgGlobalTrqTcpMax INTEGER, qosCurCfgGlobalTrqTcpRate INTEGER, qosCurCfgGlobalTrqWredState INTEGER } qosCurCfgGlobalTrqIndex OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Global Transmit Queue Number" ::= { qoSCurCfgGlobalProfileEntry 1 } qosCurCfgGlobalTrqNonTcpMin OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Global transmit queue WRED ECN nontcp profile MinThreshold value" ::= { qoSCurCfgGlobalProfileEntry 2 } qosCurCfgGlobalTrqNonTcpMax OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Global transmit queue WRED ECN nontcp profile MaxThreshold value" ::= { qoSCurCfgGlobalProfileEntry 3 } qosCurCfgGlobalTrqNonTcpRate OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Global transmit queue WRED ECN nontcp profile DropRate value" ::= { qoSCurCfgGlobalProfileEntry 4 } qosCurCfgGlobalTrqTcpMin OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Global transmit queue WRED ECN tcp profile MinThreshold value" ::= { qoSCurCfgGlobalProfileEntry 5 } qosCurCfgGlobalTrqTcpMax OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Global transmit queue WRED ECN tcp profile MaxThreshold value" ::= { qoSCurCfgGlobalProfileEntry 6 } qosCurCfgGlobalTrqTcpRate OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Global transmit queue WRED ECN tcp profile DropRate value" ::= { qoSCurCfgGlobalProfileEntry 7 } qosCurCfgGlobalTrqWredState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is for turning on/off WRED per global transmit queue" ::= { qoSCurCfgGlobalProfileEntry 8 } -- global new profile config qosNewCfgGlobalProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF QoSNewCfgGlobalProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of QOS global WRED ECN profile configuration." ::= { qoswredecn 6 } qoSNewCfgGlobalProfileEntry OBJECT-TYPE SYNTAX QoSNewCfgGlobalProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular Transmit queue of global WRED ECN profile configuration." INDEX { qosNewCfgGlobalTrqIndex} ::= { qosNewCfgGlobalProfileTable 1 } QoSNewCfgGlobalProfileEntry ::= SEQUENCE { qosNewCfgGlobalTrqIndex INTEGER, qosNewCfgGlobalTrqNonTcpMin INTEGER, qosNewCfgGlobalTrqNonTcpMax INTEGER, qosNewCfgGlobalTrqNonTcpRate INTEGER, qosNewCfgGlobalTrqTcpMin INTEGER, qosNewCfgGlobalTrqTcpMax INTEGER, qosNewCfgGlobalTrqTcpRate INTEGER, qosNewCfgGlobalTrqWredState INTEGER } qosNewCfgGlobalTrqIndex OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Global Transmit Queue Number" ::= { qoSNewCfgGlobalProfileEntry 1 } qosNewCfgGlobalTrqNonTcpMin OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Global transmit queue WRED ECN nontcp profile MinThreshold value" ::= { qoSNewCfgGlobalProfileEntry 2 } qosNewCfgGlobalTrqNonTcpMax OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Global transmit queue WRED ECN nontcp profile MaxThreshold value" ::= { qoSNewCfgGlobalProfileEntry 3 } qosNewCfgGlobalTrqNonTcpRate OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Global transmit queue WRED ECN nontcp profile DropRate value" ::= { qoSNewCfgGlobalProfileEntry 4 } qosNewCfgGlobalTrqTcpMin OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Global transmit queue WRED ECN tcp profile MinThreshold value" ::= { qoSNewCfgGlobalProfileEntry 5 } qosNewCfgGlobalTrqTcpMax OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Global transmit queue WRED ECN tcp profile MaxThreshold value" ::= { qoSNewCfgGlobalProfileEntry 6 } qosNewCfgGlobalTrqTcpRate OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Global transmit queue WRED ECN tcp profile DropRate value" ::= { qoSNewCfgGlobalProfileEntry 7 } qosNewCfgGlobalTrqWredState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is for turning on/off WRED per global transmit queue" ::= { qoSNewCfgGlobalProfileEntry 8 } -- cur global wred ecn state qosCurCfgGlobalWredState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is for turning on/off WRED globally." ::= { qoswredecn 7 } qosCurCfgGlobalEcnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is for turning on/off ECN globally." ::= { qoswredecn 8 } -- new global wred ecn state qosNewCfgGlobalWredState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is for turning on/off WRED globally." ::= { qoswredecn 9 } qosNewCfgGlobalEcnState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is for turning on/off ECN globally." ::= { qoswredecn 10 } -- ---------------------------------------------------------------------------- -- } INSERT: qos -- ---------------------------------------------------------------------------- ------------------------------------------------------------------------------- -- Feature Dependent Private MIBs for g8052-mgmt ------------------------------------------------------------------------------- acl OBJECT IDENTIFIER ::= { g8052-mgmt 9 } -- ---------------------------------------------------------------------------- -- { INSERT: acl -- ---------------------------------------------------------------------------- acConfig OBJECT IDENTIFIER ::= { acl 1 } acList OBJECT IDENTIFIER ::= { acConfig 1 } aclGroup OBJECT IDENTIFIER ::= { acConfig 3 } aclCfg OBJECT IDENTIFIER ::= { acConfig 4 } vmapConfig OBJECT IDENTIFIER ::= { acl 3 } acl6List OBJECT IDENTIFIER ::= { acConfig 5 } aclLog OBJECT IDENTIFIER ::= { acConfig 6 } mAcl OBJECT IDENTIFIER ::= { acConfig 7} -- ---------------------------------------------------------- -- -- Access Control List (ACL) Configuration -- ---------------------------------------------------------- -- aclCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AclCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of current ACL configuration." ::= { acList 1 } aclCurCfgEntry OBJECT-TYPE SYNTAX AclCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Current information about a particular ACL configuration entry." INDEX { aclCurCfgIndex } ::= { aclCurCfgTable 1 } AclCurCfgEntry ::= SEQUENCE { aclCurCfgIndex Unsigned32, aclCurCfgGroup Unsigned32, aclCurCfgFilterAction INTEGER, aclCurCfgFilterActionSetPrio INTEGER, aclCurCfgEthFmt INTEGER, aclCurCfgTagFmt INTEGER, aclCurCfgIPFmt INTEGER, aclCurCfgSrcMACAddress MacAddress, aclCurCfgSrcMACMask MacAddress, aclCurCfgDstMACAddress MacAddress, aclCurCfgDstMACMask MacAddress, aclCurCfgEthernetTypeName INTEGER, aclCurCfgEthernetTypeValue INTEGER, aclCurCfgVLanId INTEGER, aclCurCfgVLanMask DisplayString, aclCurCfg8021pPriority INTEGER, aclCurCfgTypeOfService DisplayString, aclCurCfgProtocol DisplayString, aclCurCfgSrcIPAddress IpAddress, aclCurCfgSrcIPMask IpAddress, aclCurCfgDstIPAddress IpAddress, aclCurCfgDstIPMask IpAddress, aclCurCfgSrcPort INTEGER, aclCurCfgSrcPortMask DisplayString, aclCurCfgDstPort INTEGER, aclCurCfgDstPortMask DisplayString, aclCurCfgTCPFlags BITS, aclCurCfgTCPFlagsMask BITS, aclCurCfgEgressPorts OCTET STRING, aclCurCfgStatistics INTEGER, aclCurCfgMeterAction INTEGER, aclCurCfgMeterEnable INTEGER, aclCurCfgKbitsSec Unsigned32, aclCurCfgKbitsBurst INTEGER, aclCurCfgUser INTEGER, aclCurCfgInprofDscp INTEGER, aclCurCfgTos INTEGER, aclCurCfgOutprofDscp INTEGER, aclCurCfgUserEnable INTEGER, aclCurCfgInprofDscpEnable INTEGER, aclCurCfgOutprofDscpEnable INTEGER , aclCurCfgMirrorPort Integer32 , aclCurCfgLog INTEGER } aclCurCfgIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index associated with this ACL entry." ::= { aclCurCfgEntry 1 } aclCurCfgGroup OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ACL group to which this ACL entry is a member of. A value of zero means the ACL is not a member of any group." ::= { aclCurCfgEntry 3 } aclCurCfgFilterAction OBJECT-TYPE SYNTAX INTEGER { none(0), permit(1), deny(2) ,setprio(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The action to be performed on a packet that matches the filter settings of this ACL entry." ::= { aclCurCfgEntry 4 } aclCurCfgFilterActionSetPrio OBJECT-TYPE SYNTAX INTEGER { none(0), prio0(1), prio1(2), prio2(3), prio3(4), prio4(5), prio5(6), prio6(7), prio7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value to be used when the action to be performed is setprio for this ACL entry." ::= { aclCurCfgEntry 5 } aclCurCfgEthFmt OBJECT-TYPE SYNTAX INTEGER { none(0), ethernet2(1), snap(2), llc(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The packet ethernet format to be filtered." ::= { aclCurCfgEntry 6 } aclCurCfgTagFmt OBJECT-TYPE SYNTAX INTEGER { disabled(1), any(2), untagged(3), tagged(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The packet tag format to be filtered." ::= { aclCurCfgEntry 7 } aclCurCfgIPFmt OBJECT-TYPE SYNTAX INTEGER { none(1), ipv4(2), ipv6(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The packet IP format to be filtered." ::= { aclCurCfgEntry 8 } aclCurCfgSrcMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source MAC address to be filtered." ::= { aclCurCfgEntry 9 } aclCurCfgSrcMACMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address mask applied to aclCurCfgSrcMACAddress for filtering." ::= { aclCurCfgEntry 10 } aclCurCfgDstMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination MAC address to be filtered." ::= { aclCurCfgEntry 11 } aclCurCfgDstMACMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address mask applied to aclCurCfgDstMACAddress for filtering." ::= { aclCurCfgEntry 12 } aclCurCfgEthernetTypeName OBJECT-TYPE SYNTAX INTEGER { none(0), arp(1), ipv4(2), ipv6(3), mpls(4), rarp(5), any(6), other(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Ethernet type to be filtered. If the value of this object is other(7), the value of aclNewCfgEthernetTypeValue indicates the ethernet type that will be filtered." ::= { aclCurCfgEntry 13 } aclCurCfgEthernetTypeValue OBJECT-TYPE SYNTAX INTEGER (1536..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The Ethernet type value to be filtered. The value of this object is equivalent to the value of aclNewCfgEthernetTypeName except when the value of aclNewCfgEthernetTypeName is other(7), which can be any user-defined value for this object." ::= { aclCurCfgEntry 14 } aclCurCfgVLanId OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual LAN identifier to be filtered." ::= { aclCurCfgEntry 15 } aclCurCfgVLanMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The mask applied to aclCurCfgVLanId for filtering." ::= { aclCurCfgEntry 16 } aclCurCfg8021pPriority OBJECT-TYPE SYNTAX INTEGER { none(0), priority0(1), priority1(2), priority2(3), priority3(4), priority4(5), priority5(6), priority6(7), priority7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The 802.1p priority to be filtered." ::= { aclCurCfgEntry 17 } aclCurCfgTypeOfService OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The type of service to be filtered. 'none' for not initialised, within the range 0-255" ::= { aclCurCfgEntry 18 } aclCurCfgProtocol OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol to be filtered. 'none' for not initialised, within the range 0-255" ::= { aclCurCfgEntry 19 } aclCurCfgSrcIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source IP address to be filtered." ::= { aclCurCfgEntry 20 } aclCurCfgSrcIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address mask applied to aclCurCfgSrcIPAddress for filtering." ::= { aclCurCfgEntry 21 } aclCurCfgDstIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address to be filtered." ::= { aclCurCfgEntry 22 } aclCurCfgDstIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address mask applied to aclCurCfgDstIPAddress for filtering." ::= { aclCurCfgEntry 23 } aclCurCfgSrcPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The source TCP/UDP port number to be filtered." ::= { aclCurCfgEntry 24 } aclCurCfgSrcPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The mask applied to aclCurCfgSrcPort for filtering." ::= { aclCurCfgEntry 25 } aclCurCfgDstPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination TCP/UDP port number to be filtered." ::= { aclCurCfgEntry 26 } aclCurCfgDstPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The mask applied to aclCurCfgDstPort for filtering." ::= { aclCurCfgEntry 27 } aclCurCfgTCPFlags OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP flags to be filtered. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; " ::= { aclCurCfgEntry 28 } aclCurCfgTCPFlagsMask OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP flags mask. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; " ::= { aclCurCfgEntry 39 } aclCurCfgEgressPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the ACL configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ port 9 || || || ||___ port 8 || |____ port 7 || . . . ||_________ port 2 |__________ port 1 where x: 1 - the represented port is configured for filtering. 0 - the represented port is not configured for filtering." ::= { aclCurCfgEntry 29 } aclCurCfgStatistics OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether statistics collection for this ACL is enabled or not." ::= { aclCurCfgEntry 30 } aclCurCfgMeterAction OBJECT-TYPE SYNTAX INTEGER { unconfigured(0), outdrop(1), outpass(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Meter Action for this ACL." ::= { aclCurCfgEntry 41 } aclCurCfgMeterEnable OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Meter state for this ACL." ::= { aclCurCfgEntry 42 } aclCurCfgKbitsSec OBJECT-TYPE SYNTAX Unsigned32 (64..10000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The commited rate of meter associated with this ACL entry." ::= { aclCurCfgEntry 43 } aclCurCfgKbitsBurst OBJECT-TYPE SYNTAX INTEGER { kbits32(32), kbits64(64), kbits128(128), kbits256(256), kbits512(512), kbits1024(1024), kbits2048(2048), kbits4096(4096) } MAX-ACCESS read-only STATUS current DESCRIPTION "The maxmium burst sizeof meter associated with this ACL entry." ::= { aclCurCfgEntry 44 } aclCurCfgUser OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Set user defined priority for this ACL." ::= { aclCurCfgEntry 45 } aclCurCfgInprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Set in profile pkts DSCP value." ::= { aclCurCfgEntry 46 } aclCurCfgTos OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "To enable/disable setting pkts based on TOS bits." ::= { aclCurCfgEntry 47 } aclCurCfgOutprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Set out profile pkts DSCP value." ::= { aclCurCfgEntry 48 } aclCurCfgUserEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), userdefined(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set update method for this ACL." ::= { aclCurCfgEntry 49 } aclCurCfgInprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether in profile update DSCP for this ACL is enabled or not." ::= { aclCurCfgEntry 50 } aclCurCfgOutprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether out profile update DSCP for this ACL is enabled or not." ::= { aclCurCfgEntry 51 } aclCurCfgMirrorPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Set port in the ACL for mirroring. n > 0 - the represented port is configured for mirroring. 0 - the represented port is not configured for mirroring." ::= { aclCurCfgEntry 74 } aclCurCfgLog OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether log for this ACL is enabled or not." ::= { aclCurCfgEntry 81 } -- -- New ACL Configuration Table -- aclNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AclNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of new ACL configuration." ::= { acList 2 } aclNewCfgEntry OBJECT-TYPE SYNTAX AclNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "New information about a particular ACL configuration." INDEX { aclNewCfgIndex } ::= { aclNewCfgTable 1 } AclNewCfgEntry ::= SEQUENCE { aclNewCfgIndex Unsigned32, aclNewCfgGroup Unsigned32, aclNewCfgFilterAction INTEGER, aclNewCfgFilterActionSetPrio INTEGER, aclNewCfgEthFmt INTEGER, aclNewCfgTagFmt INTEGER, aclNewCfgIPFmt INTEGER, aclNewCfgSrcMACAddress MacAddress, aclNewCfgSrcMACMask MacAddress, aclNewCfgDstMACAddress MacAddress, aclNewCfgDstMACMask MacAddress, aclNewCfgEthernetTypeName INTEGER, aclNewCfgEthernetTypeValue INTEGER, aclNewCfgVLanId INTEGER, aclNewCfgVLanMask DisplayString, aclNewCfg8021pPriority INTEGER, aclNewCfgTypeOfService DisplayString, aclNewCfgProtocol DisplayString, aclNewCfgSrcIPAddress IpAddress, aclNewCfgSrcIPMask IpAddress, aclNewCfgDstIPAddress IpAddress, aclNewCfgDstIPMask IpAddress, aclNewCfgSrcPort INTEGER, aclNewCfgSrcPortMask DisplayString, aclNewCfgDstPort INTEGER, aclNewCfgDstPortMask DisplayString, aclNewCfgTCPFlags BITS, aclNewCfgTCPFlagsMask BITS, aclNewCfgEgressPorts OCTET STRING, aclNewCfgStatistics INTEGER, aclNewCfgAddEgressPort PortNumber, aclNewCfgRemoveEgressPort PortNumber, aclNewCfgDelete INTEGER, aclNewCfgMeterAction INTEGER, aclNewCfgMeterEnable INTEGER, aclNewCfgKbitsSec Unsigned32, aclNewCfgKbitsBurst INTEGER, aclNewCfgUser INTEGER, aclNewCfgInprofDscp INTEGER, aclNewCfgTos INTEGER, aclNewCfgOutprofDscp INTEGER, aclNewCfgUserEnable INTEGER, aclNewCfgInprofDscpEnable INTEGER, aclNewCfgOutprofDscpEnable INTEGER, aclNewCfgReset INTEGER , aclNewCfgEthernetReset INTEGER , aclNewCfgIpv4Reset INTEGER , aclNewCfgTcpudpReset INTEGER , aclNewCfgMeterReset INTEGER , aclNewCfgRemarkReset INTEGER , aclNewCfgRemarkInprofReset INTEGER , aclNewCfgRemarkOutprofReset INTEGER , aclNewCfgPktfmtReset INTEGER , aclNewCfgMirrorPort Integer32 , aclNewCfgLog INTEGER } aclNewCfgIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index associated with this ACL entry." ::= { aclNewCfgEntry 1 } aclNewCfgGroup OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ACL group to which this ACL entry is a member of. A value of zero means the ACL is not a member of any group." ::= { aclNewCfgEntry 3 } aclNewCfgFilterAction OBJECT-TYPE SYNTAX INTEGER { none(0), permit(1), deny(2) ,setprio(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The action to be performed on a packet that matches the filter settings of this ACL entry." ::= { aclNewCfgEntry 4 } aclNewCfgFilterActionSetPrio OBJECT-TYPE SYNTAX INTEGER { none(0), prio0(1), prio1(2), prio2(3), prio3(4), prio4(5), prio5(6), prio6(7), prio7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The COS queue to be used when the action for this ACL entry is set to setprio." ::= { aclNewCfgEntry 5 } aclNewCfgEthFmt OBJECT-TYPE SYNTAX INTEGER { none(0), ethernet2(1), snap(2), llc(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The packet ethernet format to be filtered." ::= { aclNewCfgEntry 6 } aclNewCfgTagFmt OBJECT-TYPE SYNTAX INTEGER { disabled(1), any(2), none(3), tagged(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The packet tagging format to be filtered." ::= { aclNewCfgEntry 7 } aclNewCfgIPFmt OBJECT-TYPE SYNTAX INTEGER { none(1), ipv4(2), ipv6(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The packet IP format to be filtered." ::= { aclNewCfgEntry 8 } aclNewCfgSrcMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The source MAC address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgSrcMACMask object, if not yet set, will be automatically set to ff:ff:ff:ff:ff:ff." ::= { aclNewCfgEntry 9 } aclNewCfgSrcMACMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address mask to be applied to aclNewCfgSrcMACAddress for filtering." ::= { aclNewCfgEntry 10 } aclNewCfgDstMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The destination MAC address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgDstMACMask object, if not yet set, will be automatically set to ff:ff:ff:ff:ff:ff." ::= { aclNewCfgEntry 11 } aclNewCfgDstMACMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address mask to be applied to aclNewCfgDstMACAddress for filtering." ::= { aclNewCfgEntry 12 } aclNewCfgEthernetTypeName OBJECT-TYPE SYNTAX INTEGER { none(0), arp(1), ipv4(2), ipv6(3), mpls(4), rarp(5), any(6), other(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Ethernet type to be filtered. If the value of this object is other(7), the value of aclNewCfgEthernetTypeValue indicates the ethernet type that will be filtered. If this object is set to a value other than other(7), the value of the aclNewCfgEthernetTypeValue object is automatically set, as follows: aclNewCfgEthernetTypeName aclNewCfgEthernetTypeValue none(0) 0 arp(1) 2054 (0x0806) ipv4(2) 2048 (0x0800) ipv6(3) 34525 (0x86dd) mpls(4) 34887 (0x8847) rarp(5) 32821 (0x8035) any(6) 65535 (0xffff) " ::= { aclNewCfgEntry 13 } aclNewCfgEthernetTypeValue OBJECT-TYPE SYNTAX INTEGER (1536..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The Ethernet type value to be filtered. The value of this object is equivalent to the value of aclNewCfgEthernetTypeName except when the value of aclNewCfgEthernetTypeName is other(7), which can be any user-defined value for this object." ::= { aclNewCfgEntry 14 } aclNewCfgVLanId OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS read-write STATUS current DESCRIPTION "The virtual LAN identifier to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgVLanMask object, if not yet set, will be automatically set to 4095 (0xfff). When this object is set to 0, the Vlan ACL filter is disabled." ::= { aclNewCfgEntry 15 } aclNewCfgVLanMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The mask to be applied to aclNewCfgVLanId for filtering." ::= { aclNewCfgEntry 16 } aclNewCfg8021pPriority OBJECT-TYPE SYNTAX INTEGER { none(0), priority0(1), priority1(2), priority2(3), priority3(4), priority4(5), priority5(6), priority6(7), priority7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The 802.1p priority to be filtered." ::= { aclNewCfgEntry 17 } aclNewCfgTypeOfService OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The type of service to be filtered. 'none' for not initialised, within the range 0-255" ::= { aclNewCfgEntry 18 } aclNewCfgProtocol OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The protocol to be filtered. 'none' for not initialised, within the range 0-255" ::= { aclNewCfgEntry 19 } aclNewCfgSrcIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The source IP address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgSrcIPMask object, if not yet set, will be automatically set to 255.255.255.255." ::= { aclNewCfgEntry 20 } aclNewCfgSrcIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address mask to be applied to aclNewCfgSrcIPAddress for filtering." ::= { aclNewCfgEntry 21 } aclNewCfgDstIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The destination IP address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgDstIPMask object, if not yet set, will be automatically set to 255.255.255.255." ::= { aclNewCfgEntry 22 } aclNewCfgDstIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address mask to be applied to aclNewCfgDstIPAddress for filtering." ::= { aclNewCfgEntry 23 } aclNewCfgSrcPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The source TCP/UDP port number to be filtered. Whenever this object is set if the aclNewCfgSrcPortMask object is not set will be automatically set to 65535 (0xffff)." ::= { aclNewCfgEntry 24 } aclNewCfgSrcPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The mask to be applied to aclNewCfgSrcPort for filtering." ::= { aclNewCfgEntry 25 } aclNewCfgDstPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The destination TCP/UDP port number to be filtered. Whenever this object is set the aclNewCfgSrcPortMask object, if not yet set, will be automatically set to 65535 (0xffff)." ::= { aclNewCfgEntry 26 } aclNewCfgDstPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The mask to be applied to aclNewCfgDstPort for filtering." ::= { aclNewCfgEntry 27 } aclNewCfgTCPFlags OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP flags to be filtered. The TCP flags are presented in bitmap format, as follows: OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; " ::= { aclNewCfgEntry 28 } aclNewCfgTCPFlagsMask OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP flags mask. The TCP flags are presented in bitmap format, as follows: OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; Default value is 0x3f." ::= { aclNewCfgEntry 39 } aclNewCfgEgressPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the ACL configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ port 9 || || || ||___ port 8 || |____ port 7 || . . . ||_________ port 2 |__________ port 1 where x: 1 - the represented port is configured for filtering. 0 - the represented port is not configured for filtering." ::= { aclNewCfgEntry 29 } aclNewCfgStatistics OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether statistics collection for this ACL is enabled or not." ::= { aclNewCfgEntry 30 } aclNewCfgAddEgressPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The port to be added to the specified ACL for egress filtering. A value of zero is always returned when this object is read." ::= { aclNewCfgEntry 31 } aclNewCfgRemoveEgressPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The port to be removed from the specified ACL. A value of zero is always returned when this object is read." ::= { aclNewCfgEntry 32 } aclNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to delete an ACL entry. A value of other(1) is always returned when this object is read." ::= { aclNewCfgEntry 33 } aclNewCfgMeterAction OBJECT-TYPE SYNTAX INTEGER { unconfigured(0), outdrop(1), outpass(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Meter Action for this ACL." ::= { aclNewCfgEntry 41 } aclNewCfgMeterEnable OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Meter state for this ACL." ::= { aclNewCfgEntry 42 } aclNewCfgKbitsSec OBJECT-TYPE SYNTAX Unsigned32 (64..10000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The commited rate of meter associated with this ACL entry." ::= { aclNewCfgEntry 43 } aclNewCfgKbitsBurst OBJECT-TYPE SYNTAX INTEGER { kbits32(32), kbits64(64), kbits128(128), kbits256(256), kbits512(512), kbits1024(1024), kbits2048(2048), kbits4096(4096) } MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum burst size of the meter associated with this ACL entry." ::= { aclNewCfgEntry 44 } aclNewCfgUser OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Set user defined priority for this ACL." ::= { aclNewCfgEntry 45 } aclNewCfgInprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Set in profile pkts DSCP value." ::= { aclNewCfgEntry 46 } aclNewCfgTos OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "To enable/disable setting pkts based on TOS bits." ::= { aclNewCfgEntry 47 } aclNewCfgOutprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Set out profile pkts DSCP value." ::= { aclNewCfgEntry 48 } aclNewCfgUserEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), userdefined(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set update method for this ACL." ::= { aclNewCfgEntry 49 } aclNewCfgInprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether in profile update DSCP for this ACL is enabled or not. Only the value disable(0) can be set, causing the in profile update DSCP to be disabled for this ACL. The value enable(1) is automatically set when setting a value for aclNewCfgInprofDscp object." ::= { aclNewCfgEntry 50 } aclNewCfgOutprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether out profile update DSCP for this ACL is enabled or not. Only the value disable(0) can be set, causing the out profile update DSCP to be disabled for this ACL. The value enable(1) is automatically set when setting a value for aclNewCfgOutprofDscp object." ::= { aclNewCfgEntry 51 } aclNewCfgReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL entry. A value of other(1) is always returned when this object is read." ::= { aclNewCfgEntry 52 } aclNewCfgEthernetReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL Ethernet entry. A value of other(1) is always returned when this object is read." ::= { aclNewCfgEntry 53 } aclNewCfgIpv4Reset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL IPV4 entry. A value of other(1) is always returned when this object is read." ::= { aclNewCfgEntry 54 } aclNewCfgTcpudpReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL Tcpudp entry. A value of other(1) is always returned when this object is read." ::= { aclNewCfgEntry 55 } aclNewCfgMeterReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL Meter entry. A value of other(1) is always returned when this object is read." ::= { aclNewCfgEntry 56 } aclNewCfgRemarkReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL Remark entry. A value of other(1) is always returned when this object is read." ::= { aclNewCfgEntry 57 } aclNewCfgRemarkInprofReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL Remark Inprof entry. A value of other(1) is always returned when this object is read." ::= { aclNewCfgEntry 58 } aclNewCfgRemarkOutprofReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL Remark Outprof entry. A value of other(1) is always returned when this object is read." ::= { aclNewCfgEntry 59 } aclNewCfgPktfmtReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL Pktfmt entry. A value of other(1) is always returned when this object is read." ::= { aclNewCfgEntry 60 } aclNewCfgMirrorPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Set port in the ACL for mirroring. n > 0 - the represented port is configured for mirroring. 0 - the represented port is not configured for mirroring." ::= { aclNewCfgEntry 74 } aclNewCfgLog OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether log for this ACL is enabled or not." ::= { aclNewCfgEntry 81 } aclTableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in the acl config tables." ::= { acList 5 } -- ---------------------------------------------------------- -- -- Management Access Control List (MACL) Configuration -- ---------------------------------------------------------- -- mAclCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF MAclCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of current Management ACL configuration." ::= { mAcl 1 } mAclCurCfgEntry OBJECT-TYPE SYNTAX MAclCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Current information about a particular Management ACL configuration entry." INDEX { mAclCurCfgIndex } ::= { mAclCurCfgTable 1 } MAclCurCfgEntry ::= SEQUENCE { mAclCurCfgIndex Unsigned32, mAclCurCfgUserEnable INTEGER, mAclCurCfgFilterAction INTEGER, mAclCurCfgProtocol DisplayString, mAclCurCfgSrcIPAddress IpAddress, mAclCurCfgSrcIPMask IpAddress, mAclCurCfgDstIPAddress IpAddress, mAclCurCfgDstIPMask IpAddress, mAclCurCfgSrcPort INTEGER, mAclCurCfgSrcPortMask DisplayString, mAclCurCfgDstPort INTEGER, mAclCurCfgDstPortMask DisplayString, mAclCurCfgStatistics INTEGER } mAclCurCfgIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index associated with this Management ACL entry." ::= { mAclCurCfgEntry 1 } mAclCurCfgUserEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set update method for this mACL." ::= { mAclCurCfgEntry 2 } mAclCurCfgFilterAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The action to be performed on a packet that matches the filter settings of this mACL entry." ::= { mAclCurCfgEntry 3 } mAclCurCfgProtocol OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol to be filtered. 'none' for not initialised, within the range 0-255" ::= { mAclCurCfgEntry 4 } mAclCurCfgSrcIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source IP address to be filtered." ::= { mAclCurCfgEntry 5 } mAclCurCfgSrcIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address mask applied to mAclCurCfgSrcIPAddress for filtering." ::= { mAclCurCfgEntry 6 } mAclCurCfgDstIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address to be filtered." ::= { mAclCurCfgEntry 7 } mAclCurCfgDstIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address mask applied to mAclCurCfgDstIPAddress for filtering." ::= { mAclCurCfgEntry 8 } mAclCurCfgSrcPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The source TCP/UDP port number to be filtered." ::= { mAclCurCfgEntry 9 } mAclCurCfgSrcPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The mask applied to mAclCurCfgSrcPort for filtering." ::= { mAclCurCfgEntry 10 } mAclCurCfgDstPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination TCP/UDP port number to be filtered." ::= { mAclCurCfgEntry 11 } mAclCurCfgDstPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The mask applied to mAclCurCfgDstPort for filtering." ::= { mAclCurCfgEntry 12 } mAclCurCfgStatistics OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether statistics collection for this mACL is enabled or not." ::= { mAclCurCfgEntry 13 } -- -- New Management ACL Configuration Table -- mAclNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF MAclNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of new Management ACL configuration." ::= { mAcl 2 } mAclNewCfgEntry OBJECT-TYPE SYNTAX MAclNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "New information about a particular Management ACL configuration entry." INDEX { mAclNewCfgIndex } ::= { mAclNewCfgTable 1 } MAclNewCfgEntry ::= SEQUENCE { mAclNewCfgIndex Unsigned32, mAclNewCfgUserEnable INTEGER, mAclNewCfgFilterAction INTEGER, mAclNewCfgProtocol DisplayString, mAclNewCfgSrcIPAddress IpAddress, mAclNewCfgSrcIPMask IpAddress, mAclNewCfgDstIPAddress IpAddress, mAclNewCfgDstIPMask IpAddress, mAclNewCfgSrcPort INTEGER, mAclNewCfgSrcPortMask DisplayString, mAclNewCfgDstPort INTEGER, mAclNewCfgDstPortMask DisplayString, mAclNewCfgStatistics INTEGER, mAclNewCfgDelete INTEGER, mAclNewCfgReset INTEGER, mAclNewCfgIpv4Reset INTEGER, mAclNewCfgTcpudpReset INTEGER } mAclNewCfgIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index associated with this Management ACL entry." ::= { mAclNewCfgEntry 1 } mAclNewCfgUserEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set update method for this mACL." ::= { mAclNewCfgEntry 2 } mAclNewCfgFilterAction OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The action to be performed on a packet that matches the filter settings of this mACL entry." ::= { mAclNewCfgEntry 3 } mAclNewCfgProtocol OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The protocol to be filtered. 'none' for not initialised, within the range 0-255" ::= { mAclNewCfgEntry 4 } mAclNewCfgSrcIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The source IP address to be filtered." ::= { mAclNewCfgEntry 5 } mAclNewCfgSrcIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address mask applied to mAclNewCfgSrcIPAddress for filtering." ::= { mAclNewCfgEntry 6 } mAclNewCfgDstIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The destination IP address to be filtered." ::= { mAclNewCfgEntry 7 } mAclNewCfgDstIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address mask applied to mAclNewCfgDstIPAddress for filtering." ::= { mAclNewCfgEntry 8 } mAclNewCfgSrcPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The source TCP/UDP port number to be filtered." ::= { mAclNewCfgEntry 9 } mAclNewCfgSrcPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The mask applied to mAclNewCfgSrcPort for filtering." ::= { mAclNewCfgEntry 10 } mAclNewCfgDstPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The destination TCP/UDP port number to be filtered." ::= { mAclNewCfgEntry 11 } mAclNewCfgDstPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The mask applied to mAclNewCfgDstPort for filtering." ::= { mAclNewCfgEntry 12 } mAclNewCfgStatistics OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether statistics collection for this mACL is enabled or not." ::= { mAclNewCfgEntry 13 } mAclNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to delete an MACL entry. A value of other(1) is always returned when this object is read." ::= { mAclNewCfgEntry 14 } mAclNewCfgReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an MACL entry. A value of other(1) is always returned when this object is read." ::= { mAclNewCfgEntry 15 } mAclNewCfgIpv4Reset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL IPV4 entry. A value of other(1) is always returned when this object is read." ::= { mAclNewCfgEntry 16 } mAclNewCfgTcpudpReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an MACL Tcpudp entry. A value of other(1) is always returned when this object is read." ::= { mAclNewCfgEntry 17 } -- ---------------------------------------------------------- -- -- Access Control List6 (ACL6) Configuration -- ---------------------------------------------------------- -- acl6CurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF Acl6CurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of current ACL6 configuration." ::= { acl6List 1 } acl6CurCfgEntry OBJECT-TYPE SYNTAX Acl6CurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Current information about a particular ACL6 configuration entry." INDEX { acl6CurCfgIndex } ::= { acl6CurCfgTable 1 } Acl6CurCfgEntry ::= SEQUENCE { acl6CurCfgIndex Unsigned32, acl6CurCfgGroup Unsigned32, acl6CurCfgFilterAction INTEGER, acl6CurCfgFilterActionSetPrio INTEGER, acl6CurCfgSrcIPv6Address DisplayString, acl6CurCfgSrcIPv6PrefixLen INTEGER, acl6CurCfgDstIPv6Address DisplayString, acl6CurCfgDstIPv6PrefixLen INTEGER, acl6CurCfgIPv6FlowLabel DisplayString, acl6CurCfgIPv6TrafficClass DisplayString, acl6CurCfgIPv6NextHeader DisplayString, acl6CurCfgSrcPort INTEGER, acl6CurCfgSrcPortMask DisplayString, acl6CurCfgDstPort INTEGER, acl6CurCfgDstPortMask DisplayString, acl6CurCfgTCPFlags BITS, acl6CurCfgTCPFlagsMask BITS, acl6CurCfgEgressPorts OCTET STRING, acl6CurCfgStatistics INTEGER, acl6CurCfgUser INTEGER, acl6CurCfgInprofDscp INTEGER, acl6CurCfgTos INTEGER, acl6CurCfgUserEnable INTEGER, acl6CurCfgInprofDscpEnable INTEGER , acl6CurCfgLog INTEGER , acl6CurCfgMeterAction INTEGER , acl6CurCfgMeterEnable INTEGER , acl6CurCfgKbitsSec Unsigned32 , acl6CurCfgKbitsBurst INTEGER , acl6CurCfgOutprofDscp INTEGER , acl6CurCfgOutprofDscpEnable INTEGER } acl6CurCfgIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index associated with this ACL6 entry." ::= { acl6CurCfgEntry 1 } acl6CurCfgGroup OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ACL group to which this ACL6 entry is a member of. A value of zero means the ACL6 is not a member of any group." ::= { acl6CurCfgEntry 2 } acl6CurCfgFilterAction OBJECT-TYPE SYNTAX INTEGER { none(0), permit(1), deny(2) ,setprio(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The action to be performed on a packet that matches the filter settings of this ACL6 entry." ::= { acl6CurCfgEntry 3 } acl6CurCfgFilterActionSetPrio OBJECT-TYPE SYNTAX INTEGER { none(0), prio0(1), prio1(2), prio2(3), prio3(4), prio4(5), prio5(6), prio6(7), prio7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value to be used when the action to be performed is setprio for this ACL6 entry." ::= { acl6CurCfgEntry 4 } acl6CurCfgSrcIPv6Address OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "The source IPv6 address to be filtered. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { acl6CurCfgEntry 5 } acl6CurCfgSrcIPv6PrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 prefix applied to acl6CurCfgSrcIPv6PrefixLen for filtering." ::= { acl6CurCfgEntry 6 } acl6CurCfgDstIPv6Address OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IPv6 address to be filtered. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { acl6CurCfgEntry 7 } acl6CurCfgDstIPv6PrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 prefix applied to acl6CurCfgDstIPv6PrefixLen for filtering." ::= { acl6CurCfgEntry 8 } acl6CurCfgIPv6FlowLabel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 FlowLabel to be filtered. 'none' for not initialised, within the range 0-1048575" ::= { acl6CurCfgEntry 9 } acl6CurCfgIPv6TrafficClass OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 Traffic Class to be filtered. 'none' for not initialised, within the range 0-255" ::= { acl6CurCfgEntry 10 } acl6CurCfgIPv6NextHeader OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 next header to be filtered. 'none' for not initialised, within the range 0-255" ::= { acl6CurCfgEntry 11 } acl6CurCfgSrcPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The source TCP/UDP port number to be filtered." ::= { acl6CurCfgEntry 12 } acl6CurCfgSrcPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The mask applied to acl6CurCfgSrcPort for filtering." ::= { acl6CurCfgEntry 13 } acl6CurCfgDstPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination TCP/UDP port number to be filtered." ::= { acl6CurCfgEntry 14 } acl6CurCfgDstPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The mask applied to acl6CurCfgDstPort for filtering." ::= { acl6CurCfgEntry 15 } acl6CurCfgTCPFlags OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP flags to be filtered. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; " ::= { acl6CurCfgEntry 16 } acl6CurCfgTCPFlagsMask OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP flags mask. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; " ::= { acl6CurCfgEntry 17 } acl6CurCfgEgressPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the ACL6 configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ port 9 || || || ||___ port 8 || |____ port 7 || . . . ||_________ port 2 |__________ port 1 where x: 1 - the represented port is configured for filtering. 0 - the represented port is not configured for filtering." ::= { acl6CurCfgEntry 18 } acl6CurCfgStatistics OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether statistics collection for this ACL6 is enabled or not." ::= { acl6CurCfgEntry 19 } acl6CurCfgUser OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Set user defined priority for this ACL6." ::= { acl6CurCfgEntry 20 } acl6CurCfgInprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Set in profile pkts DSCP value." ::= { acl6CurCfgEntry 21 } acl6CurCfgTos OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "To enable/disable setting pkts based on TOS bits." ::= { acl6CurCfgEntry 22 } acl6CurCfgUserEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), userdefined(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set update method for this ACL6." ::= { acl6CurCfgEntry 24 } acl6CurCfgInprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether in profile update DSCP for this ACL6 is enabled or not." ::= { acl6CurCfgEntry 25 } acl6CurCfgLog OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether log for this ACL is enabled or not." ::= { acl6CurCfgEntry 26 } acl6CurCfgMeterAction OBJECT-TYPE SYNTAX INTEGER { unconfigured(0), outdrop(1), outpass(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Meter Action for this ACL." ::= { acl6CurCfgEntry 28 } acl6CurCfgMeterEnable OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Meter state for this ACL." ::= { acl6CurCfgEntry 29 } acl6CurCfgKbitsSec OBJECT-TYPE SYNTAX Unsigned32 (64..10000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The commited rate of meter associated with this ACL entry." ::= { acl6CurCfgEntry 30 } acl6CurCfgKbitsBurst OBJECT-TYPE SYNTAX INTEGER { kbits32(32), kbits64(64), kbits128(128), kbits256(256), kbits512(512), kbits1024(1024), kbits2048(2048), kbits4096(4096) } MAX-ACCESS read-only STATUS current DESCRIPTION "The maxmium burst sizeof meter associated with this ACL entry." ::= { acl6CurCfgEntry 31 } acl6CurCfgOutprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Set out profile pkts DSCP value." ::= { acl6CurCfgEntry 32 } acl6CurCfgOutprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether out profile update DSCP for this ACL is enabled or not." ::= { acl6CurCfgEntry 33 } -- -- New ACL6 Configuration Table -- acl6NewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF Acl6NewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of new ACL6 configuration." ::= { acl6List 2 } acl6NewCfgEntry OBJECT-TYPE SYNTAX Acl6NewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "New information about a particular ACL6 configuration." INDEX { acl6NewCfgIndex } ::= { acl6NewCfgTable 1 } Acl6NewCfgEntry ::= SEQUENCE { acl6NewCfgIndex Unsigned32, acl6NewCfgGroup Unsigned32, acl6NewCfgFilterAction INTEGER, acl6NewCfgFilterActionSetPrio INTEGER, acl6NewCfgSrcIPv6Address DisplayString, acl6NewCfgSrcIPv6PrefixLen INTEGER, acl6NewCfgDstIPv6Address DisplayString, acl6NewCfgDstIPv6PrefixLen INTEGER, acl6NewCfgIPv6FlowLabel DisplayString, acl6NewCfgIPv6TrafficClass DisplayString, acl6NewCfgIPv6NextHeader DisplayString, acl6NewCfgSrcPort INTEGER, acl6NewCfgSrcPortMask DisplayString, acl6NewCfgDstPort INTEGER, acl6NewCfgDstPortMask DisplayString, acl6NewCfgTCPFlags BITS, acl6NewCfgTCPFlagsMask BITS, acl6NewCfgEgressPorts OCTET STRING, acl6NewCfgStatistics INTEGER, acl6NewCfgAddEgressPort PortNumber, acl6NewCfgRemoveEgressPort PortNumber, acl6NewCfgDelete INTEGER, acl6NewCfgUser INTEGER, acl6NewCfgInprofDscp INTEGER, acl6NewCfgTos INTEGER, acl6NewCfgUserEnable INTEGER, acl6NewCfgInprofDscpEnable INTEGER , acl6NewCfgIPv6Reset INTEGER , acl6NewCfgTcpudpReset INTEGER , acl6NewCfgRemarkInprofReset INTEGER , acl6NewCfgLog INTEGER , acl6NewCfgMeterAction INTEGER , acl6NewCfgMeterEnable INTEGER , acl6NewCfgKbitsSec Unsigned32 , acl6NewCfgKbitsBurst INTEGER , acl6NewCfgMeterReset INTEGER , acl6NewCfgOutprofDscp INTEGER , acl6NewCfgOutprofDscpEnable INTEGER , acl6NewCfgRemarkOutprofReset INTEGER } acl6NewCfgIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index associated with this ACL6 entry." ::= { acl6NewCfgEntry 1 } acl6NewCfgGroup OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the ACL group to which this ACL6 entry is a member of. A value of zero means the ACL6 is not a member of any group." ::= { acl6NewCfgEntry 2 } acl6NewCfgFilterAction OBJECT-TYPE SYNTAX INTEGER { none(0), permit(1), deny(2) ,setprio(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The action to be performed on a packet that matches the filter settings of this ACL6 entry." ::= { acl6NewCfgEntry 3 } acl6NewCfgFilterActionSetPrio OBJECT-TYPE SYNTAX INTEGER { none(0), prio0(1), prio1(2), prio2(3), prio3(4), prio4(5), prio5(6), prio6(7), prio7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The COS queue to be used when the action for this ACL6 entry is set to setprio." ::= { acl6NewCfgEntry 4 } acl6NewCfgSrcIPv6Address OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "The source IPv6 address to be filtered. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { acl6NewCfgEntry 5 } acl6NewCfgSrcIPv6PrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The IPv6 prefix applied to acl6CurCfgSrcIPv6PrefixLen for filtering." ::= { acl6NewCfgEntry 6 } acl6NewCfgDstIPv6Address OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "The destination IPv6 address to be filtered. Address should be 4-byte hexadecimal colon notation. Valid IPv6 address should be in any of the following forms xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx or xxxx::xxxx:xxxx:xxxx:xxxx" ::= { acl6NewCfgEntry 7 } acl6NewCfgDstIPv6PrefixLen OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The IPv6 prefix applied to acl6CurCfgDstIPv6PrefixLen for filtering." ::= { acl6NewCfgEntry 8 } acl6NewCfgIPv6FlowLabel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The IPv6 flow label to be filtered. 'none' for not initialised, within the range 0-1048575" ::= { acl6NewCfgEntry 9 } acl6NewCfgIPv6TrafficClass OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The IPv6 traffic class to be filtered. 'none' for not initialised, within the range 0-255" ::= { acl6NewCfgEntry 10 } acl6NewCfgIPv6NextHeader OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The IPv6 next header to be filtered. 'none' for not initialised, within the range 0-255" ::= { acl6NewCfgEntry 11 } acl6NewCfgSrcPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The source TCP/UDP port number to be filtered." ::= { acl6NewCfgEntry 12 } acl6NewCfgSrcPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The mask applied to acl6CurCfgSrcPort for filtering." ::= { acl6NewCfgEntry 13 } acl6NewCfgDstPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The destination TCP/UDP port number to be filtered." ::= { acl6NewCfgEntry 14 } acl6NewCfgDstPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The mask applied to acl6CurCfgDstPort for filtering." ::= { acl6NewCfgEntry 15 } acl6NewCfgTCPFlags OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP flags to be filtered. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; " ::= { acl6NewCfgEntry 16 } acl6NewCfgTCPFlagsMask OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP flags mask. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; " ::= { acl6NewCfgEntry 17 } acl6NewCfgEgressPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the ACL6 configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ port 9 || || || ||___ port 8 || |____ port 7 || . . . ||_________ port 2 |__________ port 1 where x: 1 - the represented port is configured for filtering. 0 - the represented port is not configured for filtering." ::= { acl6NewCfgEntry 18 } acl6NewCfgStatistics OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether statistics collection for this ACL6 is enabled or not." ::= { acl6NewCfgEntry 19 } acl6NewCfgAddEgressPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The port to be added to the specified ACL6 for egress filtering. A value of zero is always returned when this object is read." ::= { acl6NewCfgEntry 20 } acl6NewCfgRemoveEgressPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The port to be removed from the specified ACL6. A value of zero is always returned when this object is read." ::= { acl6NewCfgEntry 21 } acl6NewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to delete an ACL6 entry. A value of other(1) is always returned when this object is read." ::= { acl6NewCfgEntry 22 } acl6NewCfgUser OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Set user defined priority for this ACL6." ::= { acl6NewCfgEntry 23 } acl6NewCfgInprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Set in profile pkts DSCP value." ::= { acl6NewCfgEntry 24 } acl6NewCfgTos OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "To enable/disable setting pkts based on TOS bits." ::= { acl6NewCfgEntry 25 } acl6NewCfgUserEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), userdefined(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set update method for this ACL6." ::= { acl6NewCfgEntry 27 } acl6NewCfgInprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether in profile update DSCP for this ACL6 is enabled or not. Only the value disable(0) can be set, causing the in profile update DSCP to be disabled for this ACL6. The value enable(1) is automatically set when setting a value for aclNewCfgInprofDscp object." ::= { acl6NewCfgEntry 28 } acl6NewCfgIPv6Reset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL IPV6 entry. A value of other(1) is always returned when this object is read." ::= { acl6NewCfgEntry 30 } acl6NewCfgTcpudpReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL6 Tcpudp entry. A value of other(1) is always returned when this object is read." ::= { acl6NewCfgEntry 31 } acl6NewCfgRemarkInprofReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL Remark Inprof entry. A value of other(1) is always returned when this object is read." ::= { acl6NewCfgEntry 32 } acl6NewCfgLog OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether log for this ACL is enabled or not." ::= { acl6NewCfgEntry 33 } acl6NewCfgMeterAction OBJECT-TYPE SYNTAX INTEGER { unconfigured(0), outdrop(1), outpass(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Meter Action for this ACL." ::= { acl6NewCfgEntry 35 } acl6NewCfgMeterEnable OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Meter state for this ACL." ::= { acl6NewCfgEntry 36 } acl6NewCfgKbitsSec OBJECT-TYPE SYNTAX Unsigned32 (64..10000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The commited rate of meter associated with this ACL entry." ::= { acl6NewCfgEntry 37 } acl6NewCfgKbitsBurst OBJECT-TYPE SYNTAX INTEGER { kbits32(32), kbits64(64), kbits128(128), kbits256(256), kbits512(512), kbits1024(1024), kbits2048(2048), kbits4096(4096) } MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum burst size of the meter associated with this ACL entry." ::= { acl6NewCfgEntry 38 } acl6NewCfgMeterReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL6 Meter entry. A value of other(1) is always returned when this object is read." ::= { acl6NewCfgEntry 39 } acl6NewCfgOutprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Set out profile pkts DSCP value." ::= { acl6NewCfgEntry 40 } acl6NewCfgOutprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether out profile update DSCP for this ACL is enabled or not. Only the value disable(0) can be set, causing the out profile update DSCP to be disabled for this ACL. The value enable(1) is automatically set when setting a value for aclNewCfgOutprofDscp object." ::= { acl6NewCfgEntry 41 } acl6NewCfgRemarkOutprofReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an ACL Remark Outprof entry. A value of other(1) is always returned when this object is read." ::= { acl6NewCfgEntry 42 } acl6TableMaxSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of entries in the acl6 config tables." ::= { acl6List 3 } -- ---------------------------------------------------------- -- -- ACL Log Configuration -- ---------------------------------------------------------- -- aclLogCurInterval OBJECT-TYPE SYNTAX INTEGER (5..600) MAX-ACCESS read-only STATUS current DESCRIPTION "The interval secends of displaying Logs. Default is 300s." ::= { aclLog 1 } aclLogNewInterval OBJECT-TYPE SYNTAX INTEGER (5..600) MAX-ACCESS read-write STATUS current DESCRIPTION "The interval secends of displaying Logs. Default is 300s." ::= { aclLog 2 } aclLogCurRateLimit OBJECT-TYPE SYNTAX INTEGER (1..1000) MAX-ACCESS read-only STATUS current DESCRIPTION "The rate limit of ACL Log queue. Default is 10pps." ::= { aclLog 3 } aclLogNewRateLimit OBJECT-TYPE SYNTAX INTEGER (1..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "The rate limit of ACL Log queue. Default is 10pps." ::= { aclLog 4 } -- ---------------------------------------------------------- -- -- ACL Group Configuration -- ---------------------------------------------------------- -- aclGroupCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AclGroupCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of current ACL Group configuration." ::= { aclGroup 1 } aclGroupCurCfgEntry OBJECT-TYPE SYNTAX AclGroupCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular ACL configuration." INDEX { aclGroupCurCfgIndex } ::= { aclGroupCurCfgTable 1 } AclGroupCurCfgEntry ::= SEQUENCE { aclGroupCurCfgIndex Unsigned32, aclGroupCurCfgMemberAcls OCTET STRING , aclGroupCurCfgMemberAcl6s OCTET STRING } aclGroupCurCfgIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index associated with this ACL Group entry." ::= { aclGroupCurCfgEntry 1 } aclGroupCurCfgMemberAcls OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The ACL members of this ACL group, presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ ACL 9 || || || ||___ ACL 8 || |____ ACL 7 || . . . ||_________ ACL 2 |__________ ACL 1 where x: 1 - the represented ACL is a member of the group. 0 - the represented ACL is not a member of the group." ::= { aclGroupCurCfgEntry 2 } aclGroupCurCfgMemberAcl6s OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The ACL6 members of this ACL group, presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ ACL6 9 || || || ||___ ACL6 8 || |____ ACL6 7 || . . . ||_________ ACL6 2 |__________ ACL6 1 where x: 1 - the represented ACL6 is a member of the group. 0 - the represented ACL6 is not a member of the group." ::= { aclGroupCurCfgEntry 9 } aclGroupNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF AclGroupNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of new ACL Group configuration." ::= { aclGroup 2 } aclGroupNewCfgEntry OBJECT-TYPE SYNTAX AclGroupNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "New information about a particular ACL configuration." INDEX { aclGroupNewCfgIndex } ::= { aclGroupNewCfgTable 1 } AclGroupNewCfgEntry ::= SEQUENCE { aclGroupNewCfgIndex Unsigned32, aclGroupNewCfgMemberAcls OCTET STRING, aclGroupNewCfgAddAcl Unsigned32, aclGroupNewCfgRemoveAcl Unsigned32, aclGroupNewCfgDelete INTEGER , aclGroupNewCfgMemberAcl6s OCTET STRING , aclGroupNewCfgAddAcl6 Unsigned32 , aclGroupNewCfgRemoveAcl6 Unsigned32 } aclGroupNewCfgIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index associated with this ACL Group entry." ::= { aclGroupNewCfgEntry 1 } aclGroupNewCfgMemberAcls OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The ACL members of this ACL group, presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ ACL 9 || || || ||___ ACL 8 || |____ ACL 7 || . . . ||_________ ACL 2 |__________ ACL 1 where x: 1 - the represented ACL is a member of the group. 0 - the represented ACL is not a member of the group." ::= { aclGroupNewCfgEntry 2 } aclGroupNewCfgAddAcl OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The index of the ACL entry to be added into this ACL group. A successful set operation on this object will also set the bit corresponding to the ACL entry in the aclGroupNewCfgMemberAcls bitmap. A value of zero is always returned when this object is read." ::= { aclGroupNewCfgEntry 4 } aclGroupNewCfgRemoveAcl OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The index of the ACL entry to be removed from this ACL group. A successful set operation on this object will unset the bit corresponding to the ACL entry in the aclGroupNewCfgMemberAcls bitmap. A value of zero is always returned when this object is read." ::= { aclGroupNewCfgEntry 5 } aclGroupNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to delete an ACL group. A value of other(1) is always returned when this object is read." ::= { aclGroupNewCfgEntry 8 } aclGroupNewCfgMemberAcl6s OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The ACL6 members of this ACL group, presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ ACL6 9 || || || ||___ ACL6 8 || |____ ACL6 7 || . . . ||_________ ACL6 2 |__________ ACL6 1 where x: 1 - the represented ACL6 is a member of the group. 0 - the represented ACL6 is not a member of the group." ::= { aclGroupNewCfgEntry 9 } aclGroupNewCfgAddAcl6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The index of the ACL6 entry to be added into this ACL group. A successful set operation on this object will also set the bit corresponding to the ACL6 entry in the aclGroupNewCfgMemberAcl6s bitmap. A value of zero is always returned when this object is read." ::= { aclGroupNewCfgEntry 10 } aclGroupNewCfgRemoveAcl6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The index of the ACL entry to be removed from this ACL group. A successful set operation on this object will unset the bit corresponding to the ACL entry in the aclGroupNewCfgMemberAcls bitmap. A value of zero is always returned when this object is read." ::= { aclGroupNewCfgEntry 11 } aclCurCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AclCurCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of port acl groups configuration." ::= { aclCfg 1 } aclCurCfgPortTableEntry OBJECT-TYPE SYNTAX AclCurCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular port acl configuration." INDEX { aclCurCfgPortIndex } ::= { aclCurCfgPortTable 1 } AclCurCfgPortTableEntry ::= SEQUENCE { aclCurCfgPortIndex PortNumber, aclCurCfgPortAclBmap OCTET STRING , aclCurCfgPortAclGrpBmap OCTET STRING , aclCurCfgPortAcl6Bmap OCTET STRING } aclCurCfgPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular port. This is also index to the entLogicalTable of Entity MIB." ::= { aclCurCfgPortTableEntry 1 } aclCurCfgPortAclBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The acls applied to the port. The acls are presented in bitmap format. This string displays acl number from 1 to 896. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ acl 9 || || || ||___ acl 8 || |____ acl 7 || . . . ||_________ acl 2 |__________ acl 1 where x : 1 - The represented acl applied to the port. 0 - The represented acl not applied to the port." ::= { aclCurCfgPortTableEntry 2 } aclCurCfgPortAclGrpBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The acl groups applied to the port. The acls are presented in bitmap format. This string displays acl number from 1 to 896. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ aclgrp 9 || || || ||___ aclgrp 8 || |____ aclgrp 7 || . . . ||_________ aclgrp 2 |__________ aclgrp 1 where x : 1 - The represented acl applied to the port. 0 - The represented acl not applied to the port." ::= { aclCurCfgPortTableEntry 4 } aclCurCfgPortAcl6Bmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The acls applied to the port. The acls are presented in bitmap format. This string displays acl number from 1 to 128. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ acl6 9 || || || ||___ acl6 8 || |____ acl6 7 || . . . ||_________ acl6 2 |__________ acl6 1 where x : 1 - The represented acl6 applied to the port. 0 - The represented acl6 not applied to the port." ::= { aclCurCfgPortTableEntry 13 } aclNewCfgPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AclNewCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of port acl configuration." ::= { aclCfg 2 } aclNewCfgPortTableEntry OBJECT-TYPE SYNTAX AclNewCfgPortTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular port acl groups configuration." INDEX { aclNewCfgPortIndex } ::= { aclNewCfgPortTable 1 } AclNewCfgPortTableEntry ::= SEQUENCE { aclNewCfgPortIndex PortNumber, aclNewCfgPortAddAcl Unsigned32 , aclNewCfgPortAddAclGrp Unsigned32 , aclNewCfgPortRemoveAcl Unsigned32 , aclNewCfgPortRemoveAclGrp Unsigned32 , aclNewCfgPortAclBmap OCTET STRING , aclNewCfgPortAclGrpBmap OCTET STRING , aclNewCfgPortAddAcl6 Unsigned32 , aclNewCfgPortRemoveAcl6 Unsigned32 , aclNewCfgPortAcl6Bmap OCTET STRING } aclNewCfgPortIndex OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of a particular port. This is also index to the entLogicalTable of Entity MIB." ::= { aclNewCfgPortTableEntry 1 } aclNewCfgPortAddAcl OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The acl to be added to the specified port. A '0' value is returned when read." ::= {aclNewCfgPortTableEntry 2 } aclNewCfgPortAddAclGrp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The acl group to be added to the specified port. A '0' value is returned when read." ::= {aclNewCfgPortTableEntry 4 } aclNewCfgPortRemoveAcl OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The acl to be removed from the specified port. A '0' value is returned when read." ::= { aclNewCfgPortTableEntry 5 } aclNewCfgPortRemoveAclGrp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The acl group to be removed from the specified port. A '0' value is returned when read." ::= { aclNewCfgPortTableEntry 7 } aclNewCfgPortAclBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The acls applied to the port. The acls are presented in bitmap format. This string displays acl number from 1 to 896. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ acl 9 || || || ||___ acl 8 || |____ acl 7 || . . . ||_________ acl 2 |__________ acl 1 where x : 1 - The represented acl applied to the port. 0 - The represented acl not applied to the port." ::= { aclNewCfgPortTableEntry 8 } aclNewCfgPortAclGrpBmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The acl groups applied to the port. The acl groups are presented in bitmap format. This string displays group number from 1 to 4096. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ aclgrp 9 || || || ||___ aclgrp 8 || |____ aclgrp 7 || . . . ||_________ aclgrp 2 |__________ aclgrp 1 where x : 1 - The represented acl group applied to the port. 0 - The represented acl group not applied to the port." ::= { aclNewCfgPortTableEntry 10 } aclNewCfgPortAddAcl6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The acl6 to be added to the specified port. A '0' value is returned when read." ::= {aclNewCfgPortTableEntry 11 } aclNewCfgPortRemoveAcl6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The acl6 to be removed from the specified port. A '0' value is returned when read." ::= { aclNewCfgPortTableEntry 12 } aclNewCfgPortAcl6Bmap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-only STATUS current DESCRIPTION "The acl6s applied to the port. The acl6s are presented in bitmap format. This string displays acl number from 1 to 128. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ acl6 9 || || || ||___ acl6 8 || |____ acl6 7 || . . . ||_________ acl6 2 |__________ acl6 1 where x : 1 - The represented acl6 applied to the port. 0 - The represented acl6 not applied to the port." ::= { aclNewCfgPortTableEntry 13 } mAclStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF MAclStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of MACL statistics." ::= { aclStats 4 } mAclStatsTableEntry OBJECT-TYPE SYNTAX MAclStatsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics about a particular MACL configuration entry." INDEX { mAclStatsIndex } ::= { mAclStatsTable 1 } MAclStatsTableEntry ::= SEQUENCE { mAclStatsIndex Integer32, mAclStatsHits Counter32, mAclClearStats INTEGER } mAclStatsIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The macl index." ::= { mAclStatsTableEntry 1 } mAclStatsHits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of hits for this MACL entry" ::= { mAclStatsTableEntry 2 } mAclClearStats OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the stats for the MACL." ::= { mAclStatsTableEntry 3 } -- ------------------------------------------------------------------------- -- -- VMAP Configuration { -- ------------------------------------------------------------------------- -- vmapList OBJECT IDENTIFIER ::= { vmapConfig 1 } vmapCfg OBJECT IDENTIFIER ::= { vmapConfig 2 } vmapVlanCfg OBJECT IDENTIFIER ::= { vmapCfg 1 } vmapGroupCfg OBJECT IDENTIFIER ::= { vmapCfg 2 } vmapVlanCfgNonServerPorts OBJECT IDENTIFIER ::= { vmapVlanCfg 1 } vmapVlanCfgServerPorts OBJECT IDENTIFIER ::= { vmapVlanCfg 2 } vmapVlanCfgAllPorts OBJECT IDENTIFIER ::= { vmapVlanCfg 3 } vmapGroupCfgNonServerPorts OBJECT IDENTIFIER ::= { vmapGroupCfg 1 } vmapGroupCfgServerPorts OBJECT IDENTIFIER ::= { vmapGroupCfg 2 } vmapGroupCfgAllPorts OBJECT IDENTIFIER ::= { vmapGroupCfg 3 } -- ------------------------------------------------------------------------- -- -- Current VMAP Configuration Table { -- ------------------------------------------------------------------------- -- vmapCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of current VMAP configuration." ::= { vmapList 1 } vmapCurCfgEntry OBJECT-TYPE SYNTAX VmapCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Current information about a particular VMAP configuration entry." INDEX { vmapCurCfgIndex } ::= { vmapCurCfgTable 1 } VmapCurCfgEntry ::= SEQUENCE { vmapCurCfgIndex Unsigned32, vmapCurCfgFilterAction INTEGER, vmapCurCfgFilterActionSetPrio INTEGER, vmapCurCfgEthFmt INTEGER, vmapCurCfgTagFmt INTEGER, vmapCurCfgIPFmt INTEGER, vmapCurCfgSrcMACAddress MacAddress, vmapCurCfgSrcMACMask MacAddress, vmapCurCfgDstMACAddress MacAddress, vmapCurCfgDstMACMask MacAddress, vmapCurCfgEthernetTypeName INTEGER, vmapCurCfgEthernetTypeValue INTEGER, vmapCurCfg8021pPriority INTEGER, vmapCurCfgTypeOfService DisplayString, vmapCurCfgProtocol DisplayString, vmapCurCfgSrcIPAddress IpAddress, vmapCurCfgSrcIPMask IpAddress, vmapCurCfgDstIPAddress IpAddress, vmapCurCfgDstIPMask IpAddress, vmapCurCfgSrcPort INTEGER, vmapCurCfgSrcPortMask DisplayString, vmapCurCfgDstPort INTEGER, vmapCurCfgDstPortMask DisplayString, vmapCurCfgTCPFlags BITS, vmapCurCfgTCPFlagsMask BITS, vmapCurCfgEgressPorts OCTET STRING, vmapCurCfgStatistics INTEGER, vmapCurCfgMeterAction INTEGER, vmapCurCfgMeterEnable INTEGER, vmapCurCfgKbitsSec Unsigned32, vmapCurCfgKbitsBurst INTEGER, vmapCurCfgUser INTEGER, vmapCurCfgInprofDscp INTEGER, vmapCurCfgTos INTEGER, vmapCurCfgOutprofDscp INTEGER, vmapCurCfgUserEnable INTEGER, vmapCurCfgInprofDscpEnable INTEGER, vmapCurCfgOutprofDscpEnable INTEGER , vmapCurCfgMirrorPort Integer32 } vmapCurCfgIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index associated with this VMAP entry." ::= { vmapCurCfgEntry 1 } vmapCurCfgFilterAction OBJECT-TYPE SYNTAX INTEGER { none(0), permit(1), deny(2), setprio(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The action to be performed on a packet that matches the filter settings of this VMAP entry." ::= { vmapCurCfgEntry 2 } vmapCurCfgFilterActionSetPrio OBJECT-TYPE SYNTAX INTEGER { none(0), prio0(1), prio1(2), prio2(3), prio3(4), prio4(5), prio5(6), prio6(7), prio7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value to be used when the action to be performed is setprio for this VMAP entry." ::= { vmapCurCfgEntry 3 } vmapCurCfgEthFmt OBJECT-TYPE SYNTAX INTEGER { none(0), ethernet2(1), snap(2), llc(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The packet ethernet format to be filtered." ::= { vmapCurCfgEntry 4 } vmapCurCfgTagFmt OBJECT-TYPE SYNTAX INTEGER { disabled(1), any(2), untagged(3), tagged(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The packet tag format to be filtered." ::= { vmapCurCfgEntry 5 } vmapCurCfgIPFmt OBJECT-TYPE SYNTAX INTEGER { none(1), ipv4(2), ipv6(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The packet IP format to be filtered." ::= { vmapCurCfgEntry 6 } vmapCurCfgSrcMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source MAC address to be filtered." ::= { vmapCurCfgEntry 7 } vmapCurCfgSrcMACMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address mask applied to aclCurCfgSrcMACAddress for filtering." ::= { vmapCurCfgEntry 8 } vmapCurCfgDstMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination MAC address to be filtered." ::= { vmapCurCfgEntry 9 } vmapCurCfgDstMACMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address mask applied to aclCurCfgDstMACAddress for filtering." ::= { vmapCurCfgEntry 10 } vmapCurCfgEthernetTypeName OBJECT-TYPE SYNTAX INTEGER { none(0), arp(1), ipv4(2), ipv6(3), mpls(4), rarp(5), any(6), other(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Ethernet type to be filtered. If the value of this object is other(7), the value of aclNewCfgEthernetTypeValue indicates the ethernet type that will be filtered." ::= { vmapCurCfgEntry 11 } vmapCurCfgEthernetTypeValue OBJECT-TYPE SYNTAX INTEGER (1536..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The Ethernet type value to be filtered. The value of this object is equivalent to the value of aclNewCfgEthernetTypeName except when the value of aclNewCfgEthernetTypeName is other(7), which can be any user-defined value for this object." ::= { vmapCurCfgEntry 12 } vmapCurCfg8021pPriority OBJECT-TYPE SYNTAX INTEGER { none(0), priority0(1), priority1(2), priority2(3), priority3(4), priority4(5), priority5(6), priority6(7), priority7(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The 802.1p priority to be filtered." ::= { vmapCurCfgEntry 13 } vmapCurCfgTypeOfService OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The type of service to be filtered. 'none' for not initialised, within the range 0-255" ::= { vmapCurCfgEntry 14 } vmapCurCfgProtocol OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol to be filtered. 'none' for not initialised, within the range 0-255" ::= { vmapCurCfgEntry 15 } vmapCurCfgSrcIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source IP address to be filtered." ::= { vmapCurCfgEntry 16 } vmapCurCfgSrcIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address mask applied to aclCurCfgSrcIPAddress for filtering." ::= { vmapCurCfgEntry 17 } vmapCurCfgDstIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address to be filtered." ::= { vmapCurCfgEntry 18 } vmapCurCfgDstIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address mask applied to aclCurCfgDstIPAddress for filtering." ::= { vmapCurCfgEntry 19 } vmapCurCfgSrcPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The source TCP/UDP port number to be filtered." ::= { vmapCurCfgEntry 20 } vmapCurCfgSrcPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The mask applied to aclCurCfgSrcPort for filtering." ::= { vmapCurCfgEntry 21 } vmapCurCfgDstPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The destination TCP/UDP port number to be filtered." ::= { vmapCurCfgEntry 22 } vmapCurCfgDstPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The mask applied to aclCurCfgDstPort for filtering." ::= { vmapCurCfgEntry 23 } vmapCurCfgTCPFlags OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP flags to be filtered. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; " ::= { vmapCurCfgEntry 24 } vmapCurCfgTCPFlagsMask OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The TCP flags mask. OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; " ::= { vmapCurCfgEntry 25 } vmapCurCfgEgressPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the VMAP configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ port 9 || || || ||___ port 8 || |____ port 7 || . . . ||_________ port 2 |__________ port 1 where x: 1 - the represented port is configured for filtering. 0 - the represented port is not configured for filtering." ::= { vmapCurCfgEntry 26 } vmapCurCfgStatistics OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether statistics collection for this VMAP is enabled or not." ::= { vmapCurCfgEntry 27 } vmapCurCfgMeterAction OBJECT-TYPE SYNTAX INTEGER { unconfigured(0), outdrop(1), outpass(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Meter Action for this VMAP." ::= { vmapCurCfgEntry 31 } vmapCurCfgMeterEnable OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Meter state for this VMAP." ::= { vmapCurCfgEntry 32 } vmapCurCfgKbitsSec OBJECT-TYPE SYNTAX Unsigned32 (64..10000000) MAX-ACCESS read-only STATUS current DESCRIPTION "The commited rate of meter associated with this VMAP entry." ::= { vmapCurCfgEntry 33 } vmapCurCfgKbitsBurst OBJECT-TYPE SYNTAX INTEGER { kbits32(32), kbits64(64), kbits128(128), kbits256(256), kbits512(512), kbits1024(1024), kbits2048(2048), kbits4096(4096) } MAX-ACCESS read-only STATUS current DESCRIPTION "The maxmium burst sizeof meter associated with this VMAP entry." ::= { vmapCurCfgEntry 34 } vmapCurCfgUser OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Set user defined priority for this VMAP." ::= { vmapCurCfgEntry 35 } vmapCurCfgInprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Set in profile pkts DSCP value." ::= { vmapCurCfgEntry 36 } vmapCurCfgTos OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "To enable/disable setting pkts based on TOS bits." ::= { vmapCurCfgEntry 37 } vmapCurCfgOutprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Set out profile pkts DSCP value." ::= { vmapCurCfgEntry 38 } vmapCurCfgUserEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), userdefined(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Set update method for this VMAP." ::= { vmapCurCfgEntry 39 } vmapCurCfgInprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether in profile update DSCP for this VMAP is enabled or not." ::= { vmapCurCfgEntry 40 } vmapCurCfgOutprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether out profile update DSCP for this VMAP is enabled or not." ::= { vmapCurCfgEntry 41 } vmapCurCfgMirrorPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Set port in the VMAP for mirroring. n > 0 - the represented port is configured for mirroring. 0 - the represented port is not configured for mirroring." ::= { vmapCurCfgEntry 51 } -- ------------------------------------------------------------------------- -- -- Current VMAP Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- New VMAP Configuration Table { -- ------------------------------------------------------------------------- -- vmapNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of new VMAP configuration." ::= { vmapList 2 } vmapNewCfgEntry OBJECT-TYPE SYNTAX VmapNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "New information about a particular VMAP configuration." INDEX { vmapNewCfgIndex } ::= { vmapNewCfgTable 1 } VmapNewCfgEntry ::= SEQUENCE { vmapNewCfgIndex Unsigned32, vmapNewCfgFilterAction INTEGER, vmapNewCfgFilterActionSetPrio INTEGER, vmapNewCfgEthFmt INTEGER, vmapNewCfgTagFmt INTEGER, vmapNewCfgIPFmt INTEGER, vmapNewCfgSrcMACAddress MacAddress, vmapNewCfgSrcMACMask MacAddress, vmapNewCfgDstMACAddress MacAddress, vmapNewCfgDstMACMask MacAddress, vmapNewCfgEthernetTypeName INTEGER, vmapNewCfgEthernetTypeValue INTEGER, vmapNewCfg8021pPriority INTEGER, vmapNewCfgTypeOfService DisplayString, vmapNewCfgProtocol DisplayString, vmapNewCfgSrcIPAddress IpAddress, vmapNewCfgSrcIPMask IpAddress, vmapNewCfgDstIPAddress IpAddress, vmapNewCfgDstIPMask IpAddress, vmapNewCfgSrcPort INTEGER, vmapNewCfgSrcPortMask DisplayString, vmapNewCfgDstPort INTEGER, vmapNewCfgDstPortMask DisplayString, vmapNewCfgTCPFlags BITS, vmapNewCfgTCPFlagsMask BITS, vmapNewCfgEgressPorts OCTET STRING, vmapNewCfgStatistics INTEGER, vmapNewCfgAddEgressPort PortNumber, vmapNewCfgRemoveEgressPort PortNumber, vmapNewCfgDelete INTEGER, vmapNewCfgMeterAction INTEGER, vmapNewCfgMeterEnable INTEGER, vmapNewCfgKbitsSec Unsigned32, vmapNewCfgKbitsBurst INTEGER, vmapNewCfgUser INTEGER, vmapNewCfgInprofDscp INTEGER, vmapNewCfgTos INTEGER, vmapNewCfgOutprofDscp INTEGER, vmapNewCfgUserEnable INTEGER, vmapNewCfgInprofDscpEnable INTEGER, vmapNewCfgOutprofDscpEnable INTEGER, vmapNewCfgReset INTEGER , vmapNewCfgEthernetReset INTEGER , vmapNewCfgIpv4Reset INTEGER , vmapNewCfgTcpudpReset INTEGER , vmapNewCfgMeterReset INTEGER , vmapNewCfgRemarkReset INTEGER , vmapNewCfgRemarkInprofReset INTEGER , vmapNewCfgRemarkOutprofReset INTEGER , vmapNewCfgPktfmtReset INTEGER , vmapNewCfgMirrorPort Integer32 } vmapNewCfgIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index associated with this VMAP entry." ::= { vmapNewCfgEntry 1 } vmapNewCfgFilterAction OBJECT-TYPE SYNTAX INTEGER { none(0), permit(1), deny(2), setprio(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The action to be performed on a packet that matches the filter settings of this VMAP entry." ::= { vmapNewCfgEntry 2 } vmapNewCfgFilterActionSetPrio OBJECT-TYPE SYNTAX INTEGER { none(0), prio0(1), prio1(2), prio2(3), prio3(4), prio4(5), prio5(6), prio6(7), prio7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The COS queue to be used when the action for this VMAP entry is set to setprio." ::= { vmapNewCfgEntry 3 } vmapNewCfgEthFmt OBJECT-TYPE SYNTAX INTEGER { none(0), ethernet2(1), snap(2), llc(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The packet ethernet format to be filtered." ::= { vmapNewCfgEntry 4 } vmapNewCfgTagFmt OBJECT-TYPE SYNTAX INTEGER { disabled(1), any(2), none(3), tagged(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The packet tagging format to be filtered." ::= { vmapNewCfgEntry 5 } vmapNewCfgIPFmt OBJECT-TYPE SYNTAX INTEGER { none(1), ipv4(2), ipv6(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The packet IP format to be filtered." ::= { vmapNewCfgEntry 6 } vmapNewCfgSrcMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The source MAC address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgSrcMACMask object, if not yet set, will be automatically set to ff:ff:ff:ff:ff:ff." ::= { vmapNewCfgEntry 7 } vmapNewCfgSrcMACMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address mask to be applied to aclNewCfgSrcMACAddress for filtering." ::= { vmapNewCfgEntry 8 } vmapNewCfgDstMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The destination MAC address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgDstMACMask object, if not yet set, will be automatically set to ff:ff:ff:ff:ff:ff." ::= { vmapNewCfgEntry 9 } vmapNewCfgDstMACMask OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address mask to be applied to aclNewCfgDstMACAddress for filtering." ::= { vmapNewCfgEntry 10 } vmapNewCfgEthernetTypeName OBJECT-TYPE SYNTAX INTEGER { none(0), arp(1), ipv4(2), ipv6(3), mpls(4), rarp(5), any(6), other(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Ethernet type to be filtered. If the value of this object is other(7), the value of aclNewCfgEthernetTypeValue indicates the ethernet type that will be filtered. If this object is set to a value other than other(7), the value of the aclNewCfgEthernetTypeValue object is automatically set, as follows: aclNewCfgEthernetTypeName aclNewCfgEthernetTypeValue none(0) 0 arp(1) 2054 (0x0806) ipv4(2) 2048 (0x0800) ipv6(3) 34525 (0x86dd) mpls(4) 34887 (0x8847) rarp(5) 32821 (0x8035) any(6) 65535 (0xffff) " ::= { vmapNewCfgEntry 11 } vmapNewCfgEthernetTypeValue OBJECT-TYPE SYNTAX INTEGER (1536..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The Ethernet type value to be filtered. The value of this object is equivalent to the value of aclNewCfgEthernetTypeName except when the value of aclNewCfgEthernetTypeName is other(7), which can be any user-defined value for this object." ::= { vmapNewCfgEntry 12 } vmapNewCfg8021pPriority OBJECT-TYPE SYNTAX INTEGER { none(0), priority0(1), priority1(2), priority2(3), priority3(4), priority4(5), priority5(6), priority6(7), priority7(8) } MAX-ACCESS read-write STATUS current DESCRIPTION "The 802.1p priority to be filtered." ::= { vmapNewCfgEntry 13 } vmapNewCfgTypeOfService OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The type of service to be filtered. 'none' for not initialised, within the range 0-255" ::= { vmapNewCfgEntry 14 } vmapNewCfgProtocol OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The protocol to be filtered. 'none' for not initialised, within the range 0-255" ::= { vmapNewCfgEntry 15 } vmapNewCfgSrcIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The source IP address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgSrcIPMask object, if not yet set, will be automatically set to 255.255.255.255." ::= { vmapNewCfgEntry 16 } vmapNewCfgSrcIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address mask to be applied to aclNewCfgSrcIPAddress for filtering." ::= { vmapNewCfgEntry 17 } vmapNewCfgDstIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The destination IP address to be filtered. Whenever this object is set to a nonzero value, the aclNewCfgDstIPMask object, if not yet set, will be automatically set to 255.255.255.255." ::= { vmapNewCfgEntry 18 } vmapNewCfgDstIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The address mask to be applied to aclNewCfgDstIPAddress for filtering." ::= { vmapNewCfgEntry 19 } vmapNewCfgSrcPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The source TCP/UDP port number to be filtered. Whenever this object is set if the aclNewCfgSrcPortMask object is not set will be automatically set to 65535 (0xffff)." ::= { vmapNewCfgEntry 20 } vmapNewCfgSrcPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The mask to be applied to aclNewCfgSrcPort for filtering." ::= { vmapNewCfgEntry 21 } vmapNewCfgDstPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The destination TCP/UDP port number to be filtered. Whenever this object is set the aclNewCfgSrcPortMask object, if not yet set, will be automatically set to 65535 (0xffff)." ::= { vmapNewCfgEntry 22 } vmapNewCfgDstPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The mask to be applied to aclNewCfgDstPort for filtering." ::= { vmapNewCfgEntry 23 } vmapNewCfgTCPFlags OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP flags to be filtered. The TCP flags are presented in bitmap format, as follows: OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; " ::= { vmapNewCfgEntry 24 } vmapNewCfgTCPFlagsMask OBJECT-TYPE SYNTAX BITS { reserved1(0), reserved2(1), tcpURG(2), tcpACK(3), tcpPSH(4), tcpRST(5), tcpSYN(6), tcpFIN(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The TCP flags mask. The TCP flags are presented in bitmap format, as follows: OCTET xxxxxxxx ||||..|| ||||..||_tcpFIN(7) ||||..|--tcpSYN(6) |||| ||||-----tcpACK(3) |||------tcpURG(2) ||-------reserved2(1) |--------reserved1(0) where: - reserved1 - 0; - reserved2 - 0; - x - 0 or 1; Default value is 0x3f." ::= { vmapNewCfgEntry 25 } vmapNewCfgEgressPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the VMAP configured for egress filtering. The ports are presented in bitmap format, as follows: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || | || || |_ port 9 || || || ||___ port 8 || |____ port 7 || . . . ||_________ port 2 |__________ port 1 where x: 1 - the represented port is configured for filtering. 0 - the represented port is not configured for filtering." ::= { vmapNewCfgEntry 26 } vmapNewCfgStatistics OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether statistics collection for this VMAP is enabled or not." ::= { vmapNewCfgEntry 27 } vmapNewCfgAddEgressPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The port to be added to the specified VMAP for egress filtering. A value of zero is always returned when this object is read." ::= { vmapNewCfgEntry 28 } vmapNewCfgRemoveEgressPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "The port to be removed from the specified VMAP. A value of zero is always returned when this object is read." ::= { vmapNewCfgEntry 29 } vmapNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to delete an VMAP entry. A value of other(1) is always returned when this object is read." ::= { vmapNewCfgEntry 30 } vmapNewCfgMeterAction OBJECT-TYPE SYNTAX INTEGER { unconfigured(0), outdrop(1), outpass(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Meter Action for this VMAP." ::= { vmapNewCfgEntry 31 } vmapNewCfgMeterEnable OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Meter state for this VMAP." ::= { vmapNewCfgEntry 32 } vmapNewCfgKbitsSec OBJECT-TYPE SYNTAX Unsigned32 (64..10000000) MAX-ACCESS read-write STATUS current DESCRIPTION "The commited rate of meter associated with this VMAP entry." ::= { vmapNewCfgEntry 33 } vmapNewCfgKbitsBurst OBJECT-TYPE SYNTAX INTEGER { kbits32(32), kbits64(64), kbits128(128), kbits256(256), kbits512(512), kbits1024(1024), kbits2048(2048), kbits4096(4096) } MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum burst size of the meter associated with this VMAP entry." ::= { vmapNewCfgEntry 34 } vmapNewCfgUser OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Set user defined priority for this VMAP." ::= { vmapNewCfgEntry 35 } vmapNewCfgInprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Set in profile pkts DSCP value." ::= { vmapNewCfgEntry 36 } vmapNewCfgTos OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "To enable/disable setting pkts based on TOS bits." ::= { vmapNewCfgEntry 37 } vmapNewCfgOutprofDscp OBJECT-TYPE SYNTAX INTEGER (0..63) MAX-ACCESS read-write STATUS current DESCRIPTION "Set out profile pkts DSCP value." ::= { vmapNewCfgEntry 38 } vmapNewCfgUserEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), userdefined(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set update method for this VMAP." ::= { vmapNewCfgEntry 39 } vmapNewCfgInprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether in profile update DSCP for this VMAP is enabled or not. Only the value disable(0) can be set, causing the in profile update DSCP to be disabled for this VMAP. The value enable(1) is automatically set when setting a value for aclNewCfgInprofDscp object." ::= { vmapNewCfgEntry 40 } vmapNewCfgOutprofDscpEnable OBJECT-TYPE SYNTAX INTEGER { disable(0), enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Whether out profile update DSCP for this VMAP is enabled or not. Only the value disable(0) can be set, causing the out profile update DSCP to be disabled for this VMAP. The value enable(1) is automatically set when setting a value for aclNewCfgOutprofDscp object." ::= { vmapNewCfgEntry 41 } vmapNewCfgReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an VMAP entry. A value of other(1) is always returned when this object is read." ::= { vmapNewCfgEntry 42 } vmapNewCfgEthernetReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an VMAP Ethernet entry. A value of other(1) is always returned when this object is read." ::= { vmapNewCfgEntry 43 } vmapNewCfgIpv4Reset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an VMAP IPV4 entry. A value of other(1) is always returned when this object is read." ::= { vmapNewCfgEntry 44 } vmapNewCfgTcpudpReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an VMAP Tcpudp entry. A value of other(1) is always returned when this object is read." ::= { vmapNewCfgEntry 45 } vmapNewCfgMeterReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an VMAP Meter entry. A value of other(1) is always returned when this object is read." ::= { vmapNewCfgEntry 46 } vmapNewCfgRemarkReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an VMAP Remark entry. A value of other(1) is always returned when this object is read." ::= { vmapNewCfgEntry 47 } vmapNewCfgRemarkInprofReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an VMAP Remark Inprof entry. A value of other(1) is always returned when this object is read." ::= { vmapNewCfgEntry 48 } vmapNewCfgRemarkOutprofReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an VMAP Remark Outprof entry. A value of other(1) is always returned when this object is read." ::= { vmapNewCfgEntry 49 } vmapNewCfgPktfmtReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reset an VMAP Pktfmt entry. A value of other(1) is always returned when this object is read." ::= { vmapNewCfgEntry 50 } vmapNewCfgMirrorPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Set port in the VMAP for mirroring. n > 0 - the represented port is configured for mirroring. 0 - the represented port is not configured for mirroring." ::= { vmapNewCfgEntry 51 } -- ------------------------------------------------------------------------- -- -- New VMAP Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- Current VLAN VMAP Non-Server Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapVlanCurCfgNonServerPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapVlanCurCfgNonServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the current configuration of vmaps for the non-server ports of vlans." ::= { vmapVlanCfgNonServerPorts 1 } vmapVlanCurCfgNonServerPortsTableEntry OBJECT-TYPE SYNTAX VmapVlanCurCfgNonServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of current configuration of vmaps for the non-server ports of vlans." INDEX { vmapVlanCurCfgNonServerPortsVlanIdx } ::= { vmapVlanCurCfgNonServerPortsTable 1 } VmapVlanCurCfgNonServerPortsTableEntry ::= SEQUENCE { vmapVlanCurCfgNonServerPortsVlanIdx Integer32, vmapVlanCurCfgNonServerPortsVmapBitmap OCTET STRING } vmapVlanCurCfgNonServerPortsVlanIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan id in the table of configured vmaps for the non-server ports of vlan" ::= { vmapVlanCurCfgNonServerPortsTableEntry 1 } vmapVlanCurCfgNonServerPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the non-server ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapVlanCurCfgNonServerPortsTableEntry 2 } -- ------------------------------------------------------------------------- -- -- Current VLAN VMAP Non-Server Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- New VLAN VMAP Non Server Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapVlanNewCfgNonServerPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapVlanNewCfgNonServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the new configuration of vmaps for non-server ports of vlans." ::= { vmapVlanCfgNonServerPorts 2 } vmapVlanNewCfgNonServerPortsTableEntry OBJECT-TYPE SYNTAX VmapVlanNewCfgNonServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of new configuration of vmaps for the non-server ports of vlans." INDEX { vmapVlanNewCfgNonServerPortsVlanIdx } ::= { vmapVlanNewCfgNonServerPortsTable 1 } VmapVlanNewCfgNonServerPortsTableEntry ::= SEQUENCE { vmapVlanNewCfgNonServerPortsVlanIdx Integer32, vmapVlanNewCfgNonServerPortsVmapBitmap OCTET STRING, vmapVlanNewCfgNonServerPortsAddVmap Unsigned32, vmapVlanNewCfgNonServerPortsRemVmap Unsigned32 } vmapVlanNewCfgNonServerPortsVlanIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan id in the table of configured vmaps for the non-server ports of vlan" ::= { vmapVlanNewCfgNonServerPortsTableEntry 1 } vmapVlanNewCfgNonServerPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the non-server ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapVlanNewCfgNonServerPortsTableEntry 2 } vmapVlanNewCfgNonServerPortsAddVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Add a new vmap to the non-server ports of the vlan" ::= { vmapVlanNewCfgNonServerPortsTableEntry 3 } vmapVlanNewCfgNonServerPortsRemVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a vmap from the non-server ports of the vlan" ::= { vmapVlanNewCfgNonServerPortsTableEntry 4 } -- ------------------------------------------------------------------------- -- -- New VLAN VMAP Non-server Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- Current VLAN VMAP Internal Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapVlanCurCfgServerPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapVlanCurCfgServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the current configuration of vmaps for server ports of vlans." ::= { vmapVlanCfgServerPorts 1 } vmapVlanCurCfgServerPortsTableEntry OBJECT-TYPE SYNTAX VmapVlanCurCfgServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of current configuration of vmaps for the server ports of vlans." INDEX { vmapVlanCurCfgServerPortsVlanIdx } ::= { vmapVlanCurCfgServerPortsTable 1 } VmapVlanCurCfgServerPortsTableEntry ::= SEQUENCE { vmapVlanCurCfgServerPortsVlanIdx Integer32, vmapVlanCurCfgServerPortsVmapBitmap OCTET STRING } vmapVlanCurCfgServerPortsVlanIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan id in the table of configured vmaps for the server ports of vlan" ::= { vmapVlanCurCfgServerPortsTableEntry 1 } vmapVlanCurCfgServerPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the server ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapVlanCurCfgServerPortsTableEntry 2 } -- ------------------------------------------------------------------------- -- -- Current VLAN VMAP Server Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- New VLAN VMAP Server Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapVlanNewCfgServerPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapVlanNewCfgServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the new configuration of vmaps for server ports of vlans." ::= { vmapVlanCfgServerPorts 2 } vmapVlanNewCfgServerPortsTableEntry OBJECT-TYPE SYNTAX VmapVlanNewCfgServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of new configuration of vmaps for the server ports of vlans." INDEX { vmapVlanNewCfgServerPortsVlanIdx } ::= { vmapVlanNewCfgServerPortsTable 1 } VmapVlanNewCfgServerPortsTableEntry ::= SEQUENCE { vmapVlanNewCfgServerPortsVlanIdx Integer32, vmapVlanNewCfgServerPortsVmapBitmap OCTET STRING, vmapVlanNewCfgServerPortsAddVmap Unsigned32, vmapVlanNewCfgServerPortsRemVmap Unsigned32 } vmapVlanNewCfgServerPortsVlanIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan id in the table of configured vmaps for the server ports of vlan" ::= { vmapVlanNewCfgServerPortsTableEntry 1 } vmapVlanNewCfgServerPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the server ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapVlanNewCfgServerPortsTableEntry 2 } vmapVlanNewCfgServerPortsAddVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Add a new vmap to the server ports of the vlan" ::= { vmapVlanNewCfgServerPortsTableEntry 3 } vmapVlanNewCfgServerPortsRemVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a vmap from the server ports of the vlan" ::= { vmapVlanNewCfgServerPortsTableEntry 4 } -- ------------------------------------------------------------------------- -- -- New VLAN VMAP Server Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- Current VLAN VMAP All Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapVlanCurCfgAllPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapVlanCurCfgAllPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the current configuration of vmaps for all ports of vlans." ::= { vmapVlanCfgAllPorts 1 } vmapVlanCurCfgAllPortsTableEntry OBJECT-TYPE SYNTAX VmapVlanCurCfgAllPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of current configuration of vmaps for all ports of vlans." INDEX { vmapVlanCurCfgAllPortsVlanIdx } ::= { vmapVlanCurCfgAllPortsTable 1 } VmapVlanCurCfgAllPortsTableEntry ::= SEQUENCE { vmapVlanCurCfgAllPortsVlanIdx Integer32, vmapVlanCurCfgAllPortsVmapBitmap OCTET STRING } vmapVlanCurCfgAllPortsVlanIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan id in the table of configured vmaps for all ports of vlan" ::= { vmapVlanCurCfgAllPortsTableEntry 1 } vmapVlanCurCfgAllPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the internal ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapVlanCurCfgAllPortsTableEntry 2 } -- ------------------------------------------------------------------------- -- -- Current VLAN VMAP All Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- New VLAN VMAP All Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapVlanNewCfgAllPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapVlanNewCfgAllPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the new configuration of vmaps for all ports of vlans." ::= { vmapVlanCfgAllPorts 2 } vmapVlanNewCfgAllPortsTableEntry OBJECT-TYPE SYNTAX VmapVlanNewCfgAllPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of new configuration of vmaps for all ports of vlans." INDEX { vmapVlanNewCfgAllPortsVlanIdx } ::= { vmapVlanNewCfgAllPortsTable 1 } VmapVlanNewCfgAllPortsTableEntry ::= SEQUENCE { vmapVlanNewCfgAllPortsVlanIdx Integer32, vmapVlanNewCfgAllPortsVmapBitmap OCTET STRING, vmapVlanNewCfgAllPortsAddVmap Unsigned32, vmapVlanNewCfgAllPortsRemVmap Unsigned32 } vmapVlanNewCfgAllPortsVlanIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan id in the table of configured vmaps for all ports of vlan" ::= { vmapVlanNewCfgAllPortsTableEntry 1 } vmapVlanNewCfgAllPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the internal ports of the vlan given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapVlanNewCfgAllPortsTableEntry 2 } vmapVlanNewCfgAllPortsAddVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Add a new vmap to all ports of the vlan" ::= { vmapVlanNewCfgAllPortsTableEntry 3 } vmapVlanNewCfgAllPortsRemVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a vmap from all vlan ports" ::= { vmapVlanNewCfgAllPortsTableEntry 4 } -- ------------------------------------------------------------------------- -- -- New VLAN VMAP All Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- Current GROUP VMAP Non-server Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapGroupCurCfgNonServerPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapGroupCurCfgNonServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the current configuration of vmaps for non-server ports of vm groups." ::= { vmapGroupCfgNonServerPorts 1 } vmapGroupCurCfgNonServerPortsTableEntry OBJECT-TYPE SYNTAX VmapGroupCurCfgNonServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of current configuration of vmaps for the non-server ports of vm groups." INDEX { vmapGroupCurCfgNonServerPortsGroupIdx } ::= { vmapGroupCurCfgNonServerPortsTable 1 } VmapGroupCurCfgNonServerPortsTableEntry ::= SEQUENCE { vmapGroupCurCfgNonServerPortsGroupIdx Integer32, vmapGroupCurCfgNonServerPortsVmapBitmap OCTET STRING } vmapGroupCurCfgNonServerPortsGroupIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vm group id in the table of configured vmaps for the non-server ports of vm group" ::= { vmapGroupCurCfgNonServerPortsTableEntry 1 } vmapGroupCurCfgNonServerPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the non-server ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapGroupCurCfgNonServerPortsTableEntry 2 } -- ------------------------------------------------------------------------- -- -- Current GROUP VMAP NonServerernal Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- New GROUP VMAP NonServerernal Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapGroupNewCfgNonServerPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapGroupNewCfgNonServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the new configuration of vmaps for non-server ports of vm groups." ::= { vmapGroupCfgNonServerPorts 2 } vmapGroupNewCfgNonServerPortsTableEntry OBJECT-TYPE SYNTAX VmapGroupNewCfgNonServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of new configuration of vmaps for the non-server ports of vm groups." INDEX { vmapGroupNewCfgNonServerPortsGroupIdx } ::= { vmapGroupNewCfgNonServerPortsTable 1 } VmapGroupNewCfgNonServerPortsTableEntry ::= SEQUENCE { vmapGroupNewCfgNonServerPortsGroupIdx Integer32, vmapGroupNewCfgNonServerPortsVmapBitmap OCTET STRING, vmapGroupNewCfgNonServerPortsAddVmap Unsigned32, vmapGroupNewCfgNonServerPortsRemVmap Unsigned32 } vmapGroupNewCfgNonServerPortsGroupIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vm group id in the table of configured vmaps for the non-server ports of vm group" ::= { vmapGroupNewCfgNonServerPortsTableEntry 1 } vmapGroupNewCfgNonServerPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the non-server ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapGroupNewCfgNonServerPortsTableEntry 2 } vmapGroupNewCfgNonServerPortsAddVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Add a new vmap to the non-server ports of the vm group" ::= { vmapGroupNewCfgNonServerPortsTableEntry 3 } vmapGroupNewCfgNonServerPortsRemVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a vmap from the non-server ports of the vm group" ::= { vmapGroupNewCfgNonServerPortsTableEntry 4 } -- ------------------------------------------------------------------------- -- -- New GROUP VMAP External Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- Current GROUP VMAP Server Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapGroupCurCfgServerPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapGroupCurCfgServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the current configuration of vmaps for server ports of vm groups." ::= { vmapGroupCfgServerPorts 1 } vmapGroupCurCfgServerPortsTableEntry OBJECT-TYPE SYNTAX VmapGroupCurCfgServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of current configuration of vmaps for the server ports of vm groups." INDEX { vmapGroupCurCfgServerPortsGroupIdx } ::= { vmapGroupCurCfgServerPortsTable 1 } VmapGroupCurCfgServerPortsTableEntry ::= SEQUENCE { vmapGroupCurCfgServerPortsGroupIdx Integer32, vmapGroupCurCfgServerPortsVmapBitmap OCTET STRING } vmapGroupCurCfgServerPortsGroupIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vm group id in the table of configured vmaps for the server ports of vm group" ::= { vmapGroupCurCfgServerPortsTableEntry 1 } vmapGroupCurCfgServerPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the server ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapGroupCurCfgServerPortsTableEntry 2 } -- ------------------------------------------------------------------------- -- -- Current GROUP VMAP Server Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- New GROUP VMAP Server Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapGroupNewCfgServerPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapGroupNewCfgServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the new configuration of vmaps for server ports of vm groups." ::= { vmapGroupCfgServerPorts 2 } vmapGroupNewCfgServerPortsTableEntry OBJECT-TYPE SYNTAX VmapGroupNewCfgServerPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of new configuration of vmaps for the server ports of vm groups." INDEX { vmapGroupNewCfgServerPortsGroupIdx } ::= { vmapGroupNewCfgServerPortsTable 1 } VmapGroupNewCfgServerPortsTableEntry ::= SEQUENCE { vmapGroupNewCfgServerPortsGroupIdx Integer32, vmapGroupNewCfgServerPortsVmapBitmap OCTET STRING, vmapGroupNewCfgServerPortsAddVmap Unsigned32, vmapGroupNewCfgServerPortsRemVmap Unsigned32 } vmapGroupNewCfgServerPortsGroupIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vm group id in the table of configured vmaps for the server ports of vm group" ::= { vmapGroupNewCfgServerPortsTableEntry 1 } vmapGroupNewCfgServerPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the server ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapGroupNewCfgServerPortsTableEntry 2 } vmapGroupNewCfgServerPortsAddVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Add a new vmap to the server ports of the vm group" ::= { vmapGroupNewCfgServerPortsTableEntry 3 } vmapGroupNewCfgServerPortsRemVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a vmap from the server ports of the vm group" ::= { vmapGroupNewCfgServerPortsTableEntry 4 } -- ------------------------------------------------------------------------- -- -- New GROUP VMAP Server Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- Current GROUP VMAP All Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapGroupCurCfgAllPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapGroupCurCfgAllPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the current configuration of vmaps for all ports of vm groups." ::= { vmapGroupCfgAllPorts 1 } vmapGroupCurCfgAllPortsTableEntry OBJECT-TYPE SYNTAX VmapGroupCurCfgAllPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of current configuration of vmaps for all ports of vm groups." INDEX { vmapGroupCurCfgAllPortsGroupIdx } ::= { vmapGroupCurCfgAllPortsTable 1 } VmapGroupCurCfgAllPortsTableEntry ::= SEQUENCE { vmapGroupCurCfgAllPortsGroupIdx Integer32, vmapGroupCurCfgAllPortsVmapBitmap OCTET STRING } vmapGroupCurCfgAllPortsGroupIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vm group id in the table of configured vmaps for all ports of vm group" ::= { vmapGroupCurCfgAllPortsTableEntry 1 } vmapGroupCurCfgAllPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the internal ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapGroupCurCfgAllPortsTableEntry 2 } -- ------------------------------------------------------------------------- -- -- Current GROUP VMAP All Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- New GROUP VMAP All Ports Configuration Table { -- ------------------------------------------------------------------------- -- vmapGroupNewCfgAllPortsTable OBJECT-TYPE SYNTAX SEQUENCE OF VmapGroupNewCfgAllPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of the new configuration of vmaps for all ports of vm groups." ::= { vmapGroupCfgAllPorts 2 } vmapGroupNewCfgAllPortsTableEntry OBJECT-TYPE SYNTAX VmapGroupNewCfgAllPortsTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the table of new configuration of vmaps for all ports of vm groups." INDEX { vmapGroupNewCfgAllPortsGroupIdx } ::= { vmapGroupNewCfgAllPortsTable 1 } VmapGroupNewCfgAllPortsTableEntry ::= SEQUENCE { vmapGroupNewCfgAllPortsGroupIdx Integer32, vmapGroupNewCfgAllPortsVmapBitmap OCTET STRING, vmapGroupNewCfgAllPortsAddVmap Unsigned32, vmapGroupNewCfgAllPortsRemVmap Unsigned32 } vmapGroupNewCfgAllPortsGroupIdx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vm group id in the table of configured vmaps for all ports of vm group" ::= { vmapGroupNewCfgAllPortsTableEntry 1 } vmapGroupNewCfgAllPortsVmapBitmap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The bitmap of vmaps configured for the internal ports of the vm group given as arguments. The vmaps are presented in bitmap format in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ vmap 9 || || || ||___ vmap 8 || |____ vmap 7 || . . . ||_________ vmap 2 |__________ vmap 1 where x : 1 - The represented vmap is active in the specified context 0 - The represented vmap is NOT active in the specified context" ::= { vmapGroupNewCfgAllPortsTableEntry 2 } vmapGroupNewCfgAllPortsAddVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Add a new vmap to all ports of the vm group" ::= { vmapGroupNewCfgAllPortsTableEntry 3 } vmapGroupNewCfgAllPortsRemVmap OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a vmap from all vm group ports" ::= { vmapGroupNewCfgAllPortsTableEntry 4 } -- ------------------------------------------------------------------------- -- -- New GROUP VMAP All Ports Configuration Table (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- VMAP Configuration (end) } -- ------------------------------------------------------------------------- -- -- ---------------------------------------------------------------------------- -- } INSERT: acl -- ---------------------------------------------------------------------------- virt OBJECT IDENTIFIER ::= { g8052-mgmt 15 } -- ---------------------------------------------------------------------------- -- { INSERT: virt -- ---------------------------------------------------------------------------- virtGeneral OBJECT IDENTIFIER ::= { virt 1 } vmGroups OBJECT IDENTIFIER ::= { virt 2 } vmPolicy OBJECT IDENTIFIER ::= { virt 3 } vmbw OBJECT IDENTIFIER ::= { vmPolicy 1 } vmProfiles OBJECT IDENTIFIER ::= { virt 4 } virtVMware OBJECT IDENTIFIER ::= { virt 5 } evb OBJECT IDENTIFIER ::= { virt 6 } vmCheck OBJECT IDENTIFIER ::= { virt 7 } vmReadyMisc OBJECT IDENTIFIER ::= { virt 8 } -- ---------------------------------------------------------- -- -- VM General Configuration -- ---------------------------------------------------------- -- virtCurCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "VM groups global state." ::= { virtGeneral 1} virtNewCfgState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/Disable Virtual Machine Groups" ::= { virtGeneral 2} virtCurCfgHbPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Current esx/esxi server to vcenter heartbeat UDP port" ::= { virtGeneral 3} virtNewCfgHbPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Set new esx/esxi server to vcenter heartbeat UDP port" ::= { virtGeneral 4} -- ------------------------------------------------------------------------- -- -- VM Virtual Center Configuration { -- ------------------------------------------------------------------------- -- virtCurCfgVirtCenterIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the Virtual Center." ::= { virtGeneral 5} virtNewCfgVirtCenterIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the Virtual Center." ::= { virtGeneral 6 } virtCurCfgVirtCenterUser OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Virtual Center username." ::= { virtGeneral 7 } virtNewCfgVirtCenterUser OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-write STATUS current DESCRIPTION "Virtual Center username." ::= { virtGeneral 8 } virtCurCfgVirtCenterSSLAuth OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Authenticate SSL Certificate." ::= { virtGeneral 9 } virtNewCfgVirtCenterSSLAuth OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authenticate SSL Certificate." ::= { virtGeneral 10 } virtNewCfgVirtCenterPasswd OBJECT-TYPE SYNTAX DisplayString(SIZE(0..129)) MAX-ACCESS read-write STATUS current DESCRIPTION "Virtual Center password." ::= { virtGeneral 11 } virtNewCfgVirtCenterDelete OBJECT-TYPE SYNTAX INTEGER { none(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete Virtual Center specifications" ::= { virtGeneral 12 } -- ------------------------------------------------------------------------- -- -- VM Virtual Center Configuration (end) } -- ------------------------------------------------------------------------- -- vmCurCfgGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF VmCurCfgGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VM groups in the current config" ::= { vmGroups 1 } vmCurCfgGroupEntry OBJECT-TYPE SYNTAX VmCurCfgGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about VM on a group in current config." INDEX { vmCurCfgGroupIndex } ::= { vmCurCfgGroupTable 1 } vmNewCfgGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF VmNewCfgGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VM groups in the new config" ::= { vmGroups 2 } vmNewCfgGroupEntry OBJECT-TYPE SYNTAX VmNewCfgGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about VM on a group in new config." INDEX { vmNewCfgGroupIndex } ::= { vmNewCfgGroupTable 1 } VmCurCfgGroupEntry ::= SEQUENCE { vmCurCfgGroupIndex Integer32, vmCurCfgGroupVlan INTEGER, vmCurCfgGroupPorts OCTET STRING, vmCurCfgGroupTagState INTEGER, vmCurCfgGroupProfileName DisplayString, vmCurCfgGroupValidateMode INTEGER, vmCurCfgGroupStg INTEGER } vmCurCfgGroupIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the vm group table." ::= { vmCurCfgGroupEntry 1} vmCurCfgGroupVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current Vlan used by the group." ::= { vmCurCfgGroupEntry 2} vmCurCfgGroupPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the VM Group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the VM Group 0 - The represented port does not belong to the VM Group" ::= { vmCurCfgGroupEntry 3} vmCurCfgGroupTagState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable VLAN tagging on all VM group ports." ::= { vmCurCfgGroupEntry 4} vmCurCfgGroupStg OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current stg of the group vlan." ::= { vmCurCfgGroupEntry 5} vmCurCfgGroupProfileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "Current profile name used by the group." ::= { vmCurCfgGroupEntry 17} vmCurCfgGroupValidateMode OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current validation mode used by the group." ::= { vmCurCfgGroupEntry 18} VmNewCfgGroupEntry ::= SEQUENCE { vmNewCfgGroupIndex Integer32, vmNewCfgGroupVlan INTEGER, vmNewCfgGroupPorts OCTET STRING, vmNewCfgGroupAddVm DisplayString, vmNewCfgGroupRemVm DisplayString, vmNewCfgGroupAddVmIdx INTEGER, vmNewCfgGroupRemVmIdx INTEGER, vmNewCfgGroupAddPort PortNumber, vmNewCfgGroupRemPort PortNumber, vmNewCfgGroupAddTrunk INTEGER, vmNewCfgGroupRemTrunk INTEGER, vmNewCfgGroupTagState INTEGER, vmNewCfgGroupAddLacpKey Unsigned32, vmNewCfgGroupRemLacpKey Unsigned32, vmNewCfgGroupAddProfile DisplayString, vmNewCfgGroupRemProfile INTEGER, vmNewCfgGroupProfileName DisplayString, vmNewCfgGroupDelete INTEGER, vmNewCfgGroupValidateMode INTEGER, vmNewCfgGroupStg INTEGER } vmNewCfgGroupIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the vm group table." ::= { vmNewCfgGroupEntry 1} vmNewCfgGroupVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set Vlan to be used by the group." ::= { vmNewCfgGroupEntry 2} vmNewCfgGroupAddVm OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Add a virtual machine to the group by UUID / Name / IP / MAC Address Note: MAC address format xx:xx:xx:xx:xx:xx" ::= { vmNewCfgGroupEntry 4} vmNewCfgGroupRemVm OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a virtual machine from the group by UUID / Name / IP / MAC Address Note: MAC address format xx:xx:xx:xx:xx:xx" ::= { vmNewCfgGroupEntry 5} vmNewCfgGroupAddVmIdx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Add virtual MAC address by index to the group." ::= { vmNewCfgGroupEntry 6} vmNewCfgGroupRemVmIdx OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a virtual MAC address by index from the group." ::= { vmNewCfgGroupEntry 7} vmNewCfgGroupAddPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "Add a port to the group." ::= { vmNewCfgGroupEntry 8} vmNewCfgGroupRemPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a port from the group." ::= { vmNewCfgGroupEntry 9} vmNewCfgGroupAddTrunk OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Add trunk to the group." ::= { vmNewCfgGroupEntry 10} vmNewCfgGroupRemTrunk OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Remove trunk from the group." ::= { vmNewCfgGroupEntry 11} vmNewCfgGroupTagState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable VLAN tagging on all VM group ports." ::= { vmNewCfgGroupEntry 12} vmNewCfgGroupAddLacpKey OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Add LACP trunk to the group." ::= { vmNewCfgGroupEntry 13} vmNewCfgGroupRemLacpKey OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Remove LACP trunk from the group." ::= { vmNewCfgGroupEntry 14} vmNewCfgGroupAddProfile OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "Add VM Profile to the group." ::= { vmNewCfgGroupEntry 15} vmNewCfgGroupRemProfile OBJECT-TYPE SYNTAX INTEGER { remove(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remove any VM profile associated with the group." ::= { vmNewCfgGroupEntry 16 } vmNewCfgGroupProfileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "New profile name to be used by the group." ::= { vmNewCfgGroupEntry 17} vmNewCfgGroupDelete OBJECT-TYPE SYNTAX INTEGER { delete(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete VM Group." ::= { vmNewCfgGroupEntry 18} vmNewCfgGroupStg OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set group vlan spanning tree group." ::= { vmNewCfgGroupEntry 19} vmNewCfgGroupPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The port list in the VM Group. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the VM Group 0 - The represented port does not belong to the VM Group" ::= { vmNewCfgGroupEntry 3} vmNewCfgGroupValidateMode OBJECT-TYPE SYNTAX INTEGER { noValidation(0), basicCheck(1), advancedCheck(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set group validation mode: noValidation : no validation will be performed. basicCheck: validate ESX port. advancedCheck: validate ESX port and VM UUID." ::= { vmNewCfgGroupEntry 20} vmCurCfgGroupMacTable OBJECT-TYPE SYNTAX SEQUENCE OF VmCurCfgGroupMaclistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Virtual machine group current configuration table." ::= {vmGroups 3 } vmCurCfgGroupMaclistEntry OBJECT-TYPE SYNTAX VmCurCfgGroupMaclistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about virtual machine group configuration. Indexes are: - vmCurCfgGroupMacGroupIndex - group number - vmCurCfgGroupMacVMIndex - virtual machine config index" INDEX { vmCurCfgGroupMacGroupIndex, vmCurCfgGroupMacVMIndex} ::= { vmCurCfgGroupMacTable 1 } VmCurCfgGroupMaclistEntry ::= SEQUENCE { vmCurCfgGroupMacGroupIndex Unsigned32, vmCurCfgGroupMacVMIndex Unsigned32, vmCurCfgGroupMacVMMac PhysAddress } vmCurCfgGroupMacGroupIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The group number for which the info is related." ::= { vmCurCfgGroupMaclistEntry 1 } vmCurCfgGroupMacVMIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual machine number for which the info is related." ::= { vmCurCfgGroupMaclistEntry 2 } vmCurCfgGroupMacVMMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "virtual machine MAC address." ::= {vmCurCfgGroupMaclistEntry 3} vmNewCfgGroupMacTable OBJECT-TYPE SYNTAX SEQUENCE OF VmNewCfgGroupMaclistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "virtual machine group new configuration table." ::= { vmGroups 4 } vmNewCfgGroupMaclistEntry OBJECT-TYPE SYNTAX VmNewCfgGroupMaclistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about virtual machine group" INDEX { vmNewCfgGroupMacGroupIndex, vmNewCfgGroupMacVMIndex} ::= { vmNewCfgGroupMacTable 1 } VmNewCfgGroupMaclistEntry ::= SEQUENCE { vmNewCfgGroupMacGroupIndex Unsigned32, vmNewCfgGroupMacVMIndex Unsigned32, vmNewCfgGroupMacVMMac PhysAddress } vmNewCfgGroupMacGroupIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The group number for which the info is related." ::= { vmNewCfgGroupMaclistEntry 1 } vmNewCfgGroupMacVMIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual machine number for which the info is related." ::= { vmNewCfgGroupMaclistEntry 2 } vmNewCfgGroupMacVMMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual machine MAC address." ::= {vmNewCfgGroupMaclistEntry 3 } -- ------------------------------------------------------------------------- -- -- VM Policy Configuration { -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- VM Bandwidth Current Configuration { -- ------------------------------------------------------------------------- -- vmbwCurCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF VmbwCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of current VM Bandwidth configuration." ::= { vmbw 1 } vmbwCurCfgEntry OBJECT-TYPE SYNTAX VmbwCurCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the current VM bandwidth table." INDEX { vmbwCurCfgMac } ::= { vmbwCurCfgTable 1 } VmbwCurCfgEntry ::= SEQUENCE { vmbwCurCfgMac MacAddress, vmbwCurCfgTxRate Unsigned32, vmbwCurCfgTxBurst Unsigned32, vmbwCurCfgTxAclId Unsigned32, vmbwCurCfgRxRate Unsigned32, vmbwCurCfgRxBurst Unsigned32, vmbwCurCfgCtrl INTEGER } vmbwCurCfgMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of VM for which bandwidth control information is related." ::= { vmbwCurCfgEntry 1 } vmbwCurCfgTxRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "VM transmit bandwidth committed rate in kbps (ingress for switch)." ::= { vmbwCurCfgEntry 2 } vmbwCurCfgTxBurst OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "VM transmit bandwidth max burst size in kilobits (ingress for switch)." ::= { vmbwCurCfgEntry 3 } vmbwCurCfgTxAclId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "ACL used for VM transmit bandwidth." ::= { vmbwCurCfgEntry 4 } vmbwCurCfgRxRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "VM receive bandwidth committed rate in kbps (egress for switch)." ::= { vmbwCurCfgEntry 5 } vmbwCurCfgRxBurst OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "VM receive bandwidth max burst size in kilobits (egress for switch)." ::= { vmbwCurCfgEntry 6 } vmbwCurCfgCtrl OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable/Disable VM bandwidth control entry." ::= { vmbwCurCfgEntry 7 } -- ------------------------------------------------------------------------- -- -- VM Bandwidth Current Configuration (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- VM Bandwidth New Configuration { -- ------------------------------------------------------------------------- -- vmbwNewCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF VmbwNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of new VM Bandwidth configuration." ::= { vmbw 2 } vmbwNewCfgEntry OBJECT-TYPE SYNTAX VmbwNewCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the new VM bandwidth table." INDEX { vmbwNewCfgMac } ::= { vmbwNewCfgTable 1 } VmbwNewCfgEntry ::= SEQUENCE { vmbwNewCfgMac MacAddress, vmbwNewCfgTxRate Unsigned32, vmbwNewCfgTxBurst Unsigned32, vmbwNewCfgTxAclId Unsigned32, vmbwNewCfgRxRate Unsigned32, vmbwNewCfgRxBurst Unsigned32, vmbwNewCfgCtrl INTEGER, vmbwNewCfgDelete INTEGER } vmbwNewCfgMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of VM for which bandwidth control information is related." ::= { vmbwNewCfgEntry 1 } vmbwNewCfgTxRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "VM transmit bandwidth committed rate in kbps (ingress for switch). Set this to zero to disable transmit bandwidth control." ::= { vmbwNewCfgEntry 2 } vmbwNewCfgTxBurst OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "VM transmit bandwidth max burst size in kilobits (ingress for switch). Set this to zero to disable transmit bandwidth control." ::= { vmbwNewCfgEntry 3 } vmbwNewCfgTxAclId OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "ACL used for VM transmit bandwidth. This is optional parameter. If set to zero the system will choose one ACL for tx bandwidth control." ::= { vmbwNewCfgEntry 4 } vmbwNewCfgRxRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "VM receive bandwidth committed rate in kbps (egress for switch). Set this to zero to disable receive bandwidth control." ::= { vmbwNewCfgEntry 5 } vmbwNewCfgRxBurst OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "VM receive bandwidth max burst size in kilobits (egress for switch). Set this to zero to disable receive bandwidth control." ::= { vmbwNewCfgEntry 6 } vmbwNewCfgCtrl OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "VM bandwidth control entry status" ::= { vmbwNewCfgEntry 7 } vmbwNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to delete a VM Bandwidth entry. other(1) is returned always when read. To delete an entry enter delete(2)." ::= { vmbwNewCfgEntry 8 } -- ------------------------------------------------------------------------- -- -- VM Bandwidth New Configuration (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- VM Policy Configuration (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- VM Check Configuration { -- ------------------------------------------------------------------------- -- vmCurCfgCheck OBJECT IDENTIFIER ::= { vmCheck 1 } vmNewCfgCheck OBJECT IDENTIFIER ::= { vmCheck 2 } vmCurCfgCheckActionBasic OBJECT-TYPE SYNTAX INTEGER { log(1), link(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current settings for basic checking mode" ::= { vmCurCfgCheck 1 } vmCurCfgCheckActionAdvanced OBJECT-TYPE SYNTAX INTEGER { log(1), link(2), acl(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current settings for advanced checking mode" ::= { vmCurCfgCheck 2 } vmCurCfgCheckAclsMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current value for the maximum number of ACLs that can be used by Mac Spoofing Check feature" ::= { vmCurCfgCheck 3 } vmCurCfgCheckTrust OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Current value for the configured trusted port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the trusted ports list 0 - The represented port does not belong to the trusted ports list" ::= { vmCurCfgCheck 4 } vmNewCfgCheckActionBasic OBJECT-TYPE SYNTAX INTEGER { log(1), link(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "New settings for basic checking mode" ::= { vmNewCfgCheck 1 } vmNewCfgCheckActionAdvanced OBJECT-TYPE SYNTAX INTEGER { log(1), link(2), acl(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "New settings for advanced checking mode" ::= { vmNewCfgCheck 2 } vmNewCfgCheckAclsMax OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "New value for the maximum number of ACLs that can be used by Mac Spoofing Check feature" ::= { vmNewCfgCheck 3 } vmNewCfgCheckTrust OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "New value for the configured trusted port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the trusted ports list 0 - The represented port does not belong to the trusted ports list" ::= { vmNewCfgCheck 4 } vmNewCfgCheckTrustAddPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "Add port to the configured trusted port list." ::= { vmNewCfgCheck 5 } vmNewCfgCheckTrustRemPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "Remove port from the configured trusted port list." ::= { vmNewCfgCheck 6 } -- ------------------------------------------------------------------------- -- -- VM Profiles Configuration { -- ------------------------------------------------------------------------- -- vmCurCfgProfilesTable OBJECT-TYPE SYNTAX SEQUENCE OF VmCurCfgProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VM profiles in the current config" ::= { vmProfiles 1 } vmCurCfgProfileEntry OBJECT-TYPE SYNTAX VmCurCfgProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a VM profile in current config." INDEX { vmCurCfgProfileIndex } ::= { vmCurCfgProfilesTable 1 } VmCurCfgProfileEntry ::= SEQUENCE { vmCurCfgProfileIndex Integer32, vmCurCfgProfileName DisplayString, vmCurCfgProfileVlan INTEGER, vmCurCfgProfileShapingAverage Integer32, vmCurCfgProfileShapingBurst Integer32, vmCurCfgProfileShapingPeak Integer32 , vmCurCfgProfileEgressShapingAverage Integer32, vmCurCfgProfileEgressShapingBurst Integer32, vmCurCfgProfileEgressShapingPeak Integer32 } vmCurCfgProfileIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the vm profiles table (1..32)." ::= { vmCurCfgProfileEntry 1} vmCurCfgProfileName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-only STATUS current DESCRIPTION "VM Profile name." ::= { vmCurCfgProfileEntry 2} vmCurCfgProfileVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current VM Profile VLAN Id" ::= { vmCurCfgProfileEntry 3} vmCurCfgProfileShapingAverage OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current VM Profile Shaping Average." ::= { vmCurCfgProfileEntry 4} vmCurCfgProfileShapingBurst OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current VM Profile Shaping Burst." ::= { vmCurCfgProfileEntry 5} vmCurCfgProfileShapingPeak OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current VM Profile Shaping Peak." ::= { vmCurCfgProfileEntry 6} vmCurCfgProfileEgressShapingAverage OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current VM Profile Egress Shaping Average." ::= { vmCurCfgProfileEntry 7} vmCurCfgProfileEgressShapingBurst OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current VM Profile Egress Shaping Burst." ::= { vmCurCfgProfileEntry 8} vmCurCfgProfileEgressShapingPeak OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current VM Profile Egress Shaping Peak." ::= { vmCurCfgProfileEntry 9} vmNewCfgProfilesTable OBJECT-TYPE SYNTAX SEQUENCE OF VmNewCfgProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VM profiles in the current config" ::= { vmProfiles 2 } vmNewCfgProfileEntry OBJECT-TYPE SYNTAX VmNewCfgProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a VM profile in current config." INDEX { vmNewCfgProfileIndex } ::= { vmNewCfgProfilesTable 1 } VmNewCfgProfileEntry ::= SEQUENCE { vmNewCfgProfileIndex Integer32, vmNewCfgProfileName DisplayString, vmNewCfgProfileVlan INTEGER, vmNewCfgProfileShapingAverage Integer32, vmNewCfgProfileShapingBurst Integer32, vmNewCfgProfileShapingPeak Integer32, vmNewCfgProfileDelete INTEGER , vmNewCfgProfileEgressShapingAverage Integer32, vmNewCfgProfileEgressShapingBurst Integer32, vmNewCfgProfileEgressShapingPeak Integer32 } vmNewCfgProfileIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the vm profiles table (1..32)." ::= { vmNewCfgProfileEntry 1} vmNewCfgProfileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..39)) MAX-ACCESS read-write STATUS current DESCRIPTION "VM Profile name." ::= { vmNewCfgProfileEntry 2} vmNewCfgProfileVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Vlan to be used by the VM profile." ::= { vmNewCfgProfileEntry 3} vmNewCfgProfileShapingAverage OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Shaping average to be used by the VM profile." ::= { vmNewCfgProfileEntry 4} vmNewCfgProfileShapingBurst OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Shaping burst to be used by the VM profile." ::= { vmNewCfgProfileEntry 5} vmNewCfgProfileShapingPeak OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Shaping peak to be used by the VM profile." ::= { vmNewCfgProfileEntry 6} vmNewCfgProfileDelete OBJECT-TYPE SYNTAX INTEGER { none(1), delete(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Delete VM Profile." ::= { vmNewCfgProfileEntry 7} vmNewCfgProfileEgressShapingAverage OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Egress shaping average to be used by the VM profile." ::= { vmNewCfgProfileEntry 8} vmNewCfgProfileEgressShapingBurst OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Egress shaping burst to be used by the VM profile." ::= { vmNewCfgProfileEntry 9} vmNewCfgProfileEgressShapingPeak OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Egress shaping peak to be used by the VM profile." ::= { vmNewCfgProfileEntry 10} -- ------------------------------------------------------------------------- -- -- VM Profiles Configuration (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- VMware information -- ------------------------------------------------------------------------- -- virtVMwareNameTableUpdate OBJECT-TYPE SYNTAX INTEGER { ok(1), get(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to get information from the Virtual Center. Set this value to get(2) to update the host and VM name tables: virtVMwareHostNameTable, virtVMwareVMNameTable with information from the Virtual Center. These two tables can be querried by subsequent Get operations without accessing the Virtual Center. To refresh these two tables, set virtVMwareNameTableUpdate again. ok(1) is returned always when read." ::= { virtVMware 1 } virtVMwareHostNameTable OBJECT-TYPE SYNTAX SEQUENCE OF VirtVMwareHostNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of names of VMware hosts in the Virtual Center." ::= { virtVMware 2 } virtVMwareHostNameEntry OBJECT-TYPE SYNTAX VirtVMwareHostNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about names of VMware hosts in the Data Center." INDEX { virtVMwareHostNameIndex } ::= { virtVMwareHostNameTable 1 } VirtVMwareHostNameEntry ::= SEQUENCE { virtVMwareHostNameIndex Integer32, virtVMwareHostNameUUID DisplayString, virtVMwareHostNameIpAddress DisplayString, virtVMwareHostNameName DisplayString } virtVMwareHostNameIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the virtVMwareHostNameTable table." ::= { virtVMwareHostNameEntry 1} virtVMwareHostNameUUID OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The UUID of a VMware host." ::= { virtVMwareHostNameEntry 2} virtVMwareHostNameIpAddress OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of a VMware host." ::= { virtVMwareHostNameEntry 3} virtVMwareHostNameName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of a VMware host." ::= { virtVMwareHostNameEntry 4} virtVMwareVMNameTable OBJECT-TYPE SYNTAX SEQUENCE OF VirtVMwareVMNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VMware virtual machines in the Data Center." ::= { virtVMware 3 } virtVMwareVMNameEntry OBJECT-TYPE SYNTAX VirtVMwareVMNameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about VMware virtual machines in the Data Center." INDEX { virtVMwareVMNameIndex } ::= { virtVMwareVMNameTable 1 } VirtVMwareVMNameEntry ::= SEQUENCE { virtVMwareVMNameIndex Integer32, virtVMwareVMNameUUID DisplayString, virtVMwareVMNameVMwareName DisplayString, virtVMwareVMNameOsName DisplayString, virtVMwareVMNameIpAddress DisplayString } virtVMwareVMNameIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the VMware virtual machine table in the Data Center." ::= { virtVMwareVMNameEntry 1} virtVMwareVMNameUUID OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The UUID of a virtual machine." ::= { virtVMwareVMNameEntry 2} virtVMwareVMNameVMwareName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of a virtual machine given by VMware." ::= { virtVMwareVMNameEntry 3} virtVMwareVMNameOsName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of a virtual machine given by the host OS." ::= { virtVMwareVMNameEntry 4} virtVMwareVMNameIpAddress OBJECT-TYPE SYNTAX DisplayString(SIZE(0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of a virtual machine." ::= { virtVMwareVMNameEntry 5} virtVMwareHost OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "VMware host ID This is an action object to get information about a specific host from the Virtual Center. This object specifies the host ID by UUID / IP Address / Name. Setting this objects populates the following 3 tables: virtVMwareHostVswitchTable, virtVMwareHostPGTable, virtVMwareHostDetailInfoTable with the host's networking information from the Virtul Center. These three tables can be querried by subsequent Get operations without accessing the Virtual Center. To refresh these tables, set this object to the target host." ::= { virtVMware 4 } virtVMwareHostVswitchTable OBJECT-TYPE SYNTAX SEQUENCE OF VirtVMwareHostVswitchEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Vswitches available on the specified host." ::= { virtVMware 5 } virtVMwareHostVswitchEntry OBJECT-TYPE SYNTAX VirtVMwareHostVswitchEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about Vswitches available on the specified host." INDEX { virtVMwareHostVswitchIndex } ::= { virtVMwareHostVswitchTable 1 } VirtVMwareHostVswitchEntry ::= SEQUENCE { virtVMwareHostVswitchIndex Integer32, virtVMwareHostVswitchName DisplayString } virtVMwareHostVswitchIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the Vswitch table on the specified host." ::= { virtVMwareHostVswitchEntry 1} virtVMwareHostVswitchName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of a Vswitch on the specified host." ::= { virtVMwareHostVswitchEntry 2} virtVMwareHostPGTable OBJECT-TYPE SYNTAX SEQUENCE OF VirtVMwareHostPGEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of Port Groups available on the specified host." ::= { virtVMware 6 } virtVMwareHostPGEntry OBJECT-TYPE SYNTAX VirtVMwareHostPGEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about Port Groups available on the specified host." INDEX { virtVMwareHostPGIndex } ::= { virtVMwareHostPGTable 1 } VirtVMwareHostPGEntry ::= SEQUENCE { virtVMwareHostPGIndex Integer32, virtVMwareHostPGName DisplayString, virtVMwareHostPGVswitchName DisplayString } virtVMwareHostPGIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the Port Group table on the specified host." ::= { virtVMwareHostPGEntry 1} virtVMwareHostPGName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of a Port Group on the specified host." ::= { virtVMwareHostPGEntry 2} virtVMwareHostPGVswitchName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of a Vswitch on the specified host." ::= { virtVMwareHostPGEntry 3} virtVMwareHostDetailInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF VirtVMwareHostDetailInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of detailed information available on the specified host/VM interface." ::= { virtVMware 7 } virtVMwareHostDetailInfoEntry OBJECT-TYPE SYNTAX VirtVMwareHostDetailInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Detailed information available on the specified host/VM interface." INDEX { virtVMwareHostDetailInfoIndex } ::= { virtVMwareHostDetailInfoTable 1 } VirtVMwareHostDetailInfoEntry ::= SEQUENCE { virtVMwareHostDetailInfoIndex Integer32, virtVMwareHostDetailInfoMACAddr DisplayString, virtVMwareHostDetailInfoPort DisplayString, virtVMwareHostDetailInfoType DisplayString, virtVMwareHostDetailInfoIPAddr DisplayString, virtVMwareHostDetailInfoUUID DisplayString, virtVMwareHostDetailInfoVswitch DisplayString, virtVMwareHostDetailInfoPortGroup DisplayString, virtVMwareHostDetailInfoVlanID DisplayString, virtVMwareHostDetailInfoHostName DisplayString, virtVMwareHostDetailInfoVMVCenterName DisplayString, virtVMwareHostDetailInfoVMOSHostName DisplayString, virtVMwareHostDetailInfoVMCurrentHost DisplayString } virtVMwareHostDetailInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the detailed information table on the specified host/VM interface." ::= { virtVMwareHostDetailInfoEntry 1} virtVMwareHostDetailInfoMACAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the host/VM interface." ::= { virtVMwareHostDetailInfoEntry 2} virtVMwareHostDetailInfoPort OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the specified host/VM interface." ::= { virtVMwareHostDetailInfoEntry 3} virtVMwareHostDetailInfoType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Interface type" ::= { virtVMwareHostDetailInfoEntry 4} virtVMwareHostDetailInfoIPAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the specified host/VM interface." ::= { virtVMwareHostDetailInfoEntry 5} virtVMwareHostDetailInfoUUID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The UUID of the specified host/VM interface." ::= { virtVMwareHostDetailInfoEntry 6} virtVMwareHostDetailInfoVswitch OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the virtual switch of the specified host/VM interface." ::= { virtVMwareHostDetailInfoEntry 7} virtVMwareHostDetailInfoPortGroup OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the port group of the specified host/VM interface." ::= { virtVMwareHostDetailInfoEntry 8} virtVMwareHostDetailInfoVlanID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the specified host/VM interface." ::= { virtVMwareHostDetailInfoEntry 9} virtVMwareHostDetailInfoHostName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the specified host interface. N/A for VMs." ::= { virtVMwareHostDetailInfoEntry 10} virtVMwareHostDetailInfoVMVCenterName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the Virtual Center of the specified VM interface. N/A for host interfaces." ::= { virtVMwareHostDetailInfoEntry 11} virtVMwareHostDetailInfoVMOSHostName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the VM set by the host operating system. N/A for host interfaces." ::= { virtVMwareHostDetailInfoEntry 12} virtVMwareHostDetailInfoVMCurrentHost OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the host of the specified VM. N/A for host interfaces." ::= { virtVMwareHostDetailInfoEntry 13} virtVMwareVM OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "VMware virtual machine ID This is an action object to get information about a specific virtual machine from the Virtual Center. This object specifies the VM ID by by UUID / IP Address / Name. Setting this object populates the virtVMwareVMInfoTable table with networking information for this VM from the Virtual Center. This table can be querried by subsequent Get operations without accessing the Virtual Center. To refresh the table, set this object to the target VM. " ::= { virtVMware 8 } virtVMwareVMInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF VirtVMwareVMInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of networking information available on the specified VM." ::= { virtVMware 9 } virtVMwareVMInfoEntry OBJECT-TYPE SYNTAX VirtVMwareVMInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Detailed information available on the specified VM." INDEX { virtVMwareVMInfoIndex } ::= { virtVMwareVMInfoTable 1 } VirtVMwareVMInfoEntry ::= SEQUENCE { virtVMwareVMInfoIndex Integer32, virtVMwareVMInfoMACAddr DisplayString, virtVMwareVMInfoPort DisplayString, virtVMwareVMInfoType DisplayString, virtVMwareVMInfoIPAddr DisplayString, virtVMwareVMInfoUUID DisplayString, virtVMwareVMInfoVswitch DisplayString, virtVMwareVMInfoPortGroup DisplayString, virtVMwareVMInfoVlanID DisplayString, virtVMwareVMInfoVMVCenterName DisplayString, virtVMwareVMInfoVMOSHostName DisplayString, virtVMwareVMInfoVMCurrentHost DisplayString } virtVMwareVMInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the table with information on the specified VM." ::= { virtVMwareVMInfoEntry 1} virtVMwareVMInfoMACAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the specified VM." ::= { virtVMwareVMInfoEntry 2} virtVMwareVMInfoPort OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The port number of the specified VM." ::= { virtVMwareVMInfoEntry 3} virtVMwareVMInfoType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Interface type" ::= { virtVMwareVMInfoEntry 4} virtVMwareVMInfoIPAddr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the specified VM." ::= { virtVMwareVMInfoEntry 5} virtVMwareVMInfoUUID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The UUID of the specified VM." ::= { virtVMwareVMInfoEntry 6} virtVMwareVMInfoVswitch OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the virtual switch of the specified VM." ::= { virtVMwareVMInfoEntry 7} virtVMwareVMInfoPortGroup OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the port group of the specified VM." ::= { virtVMwareVMInfoEntry 8} virtVMwareVMInfoVlanID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of the specified VM." ::= { virtVMwareVMInfoEntry 9} virtVMwareVMInfoVMVCenterName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the Virtual Center of the specified VM." ::= { virtVMwareVMInfoEntry 10} virtVMwareVMInfoVMOSHostName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the VM set by the host operating system." ::= { virtVMwareVMInfoEntry 11} virtVMwareVMInfoVMCurrentHost OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the host of the specified VM." ::= { virtVMwareVMInfoEntry 12} virtCurCfgVMwareHello OBJECT IDENTIFIER ::= { virtVMware 10 } virtNewCfgVMwareHello OBJECT IDENTIFIER ::= { virtVMware 11 } virtCurCfgVMwareHelloEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current value for hello advertising status" ::= { virtCurCfgVMwareHello 1 } virtCurCfgVMwareHelloTimer OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current hello packet send interval" ::= { virtCurCfgVMwareHello 2 } virtCurCfgVMwareHelloPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Current value for the configured hello port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the hello ports list 0 - The represented port does not belong to the hello ports list" ::= { virtCurCfgVMwareHello 3 } virtCurCfgVMwareHelloAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Current VM hello IP address" ::= { virtCurCfgVMwareHello 4 } virtNewCfgVMwareHelloEnable OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "New value for hello advertising status" ::= { virtNewCfgVMwareHello 1 } virtNewCfgVMwareHelloTimer OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "New hello packet send interval" ::= { virtNewCfgVMwareHello 2 } virtNewCfgVMwareHelloPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "New value for the configured hello port list. The ports are presented in bitmap format. in receiving order: OCTET 1 OCTET 2 ..... xxxxxxxx xxxxxxxx ..... || || |_ port 8 || || || ||___ port 7 || |____ port 6 || . . . ||_________ port 1 |__________ reserved where x : 1 - The represented port belongs to the hello ports list 0 - The represented port does not belong to the hello ports list" ::= { virtNewCfgVMwareHello 3 } virtNewCfgVMwareHelloAddPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "Add a port to the hello port list" ::= { virtNewCfgVMwareHello 4 } virtNewCfgVMwareHelloRemovePort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-write STATUS current DESCRIPTION "Remove a port from the hello port list" ::= { virtNewCfgVMwareHello 5 } virtNewCfgVMwareHelloAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "New VM hello IP address" ::= { virtNewCfgVMwareHello 6 } -- ------------------------------------------------------------------------- -- -- VMware information (end) } -- ------------------------------------------------------------------------- -- -- ---------------------------------------------------------------------------- -- VMReady Information { -- ---------------------------------------------------------------------------- agVMGroupInfo OBJECT IDENTIFIER ::= { agentInfo 12 } vmGroupInfoTbl OBJECT-TYPE SYNTAX SEQUENCE OF VMGroupInfolistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Virtual MAC information table" ::= { agVMGroupInfo 1 } vmGroupInfolistEntry OBJECT-TYPE SYNTAX VMGroupInfolistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The run-time information about a virtual machine" INDEX { vmGroupInfoIdx } ::= { vmGroupInfoTbl 1 } VMGroupInfolistEntry ::= SEQUENCE { vmGroupInfoIdx Unsigned32, vmGroupInfoMac PhysAddress, vmGroupInfoIP IpAddress, vmGroupInfoPort PortNumber, vmGroupInfoGroup Unsigned32, vmGroupInfoVlan Unsigned32, vmGroupInfoIsESXSvcCon Unsigned32 ,vmGroupInfoIsVMK Unsigned32, vmGroupInfoName DisplayString, vmGroupInfoUUID DisplayString, vmGroupInfoVSwitch DisplayString, vmGroupInfoPortGroup DisplayString, vmGroupInfoHost DisplayString } vmGroupInfoIdx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Table index, 1 based." ::= { vmGroupInfolistEntry 1 } vmGroupInfoMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual machine MAC address." ::= {vmGroupInfolistEntry 2 } vmGroupInfoIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual machine IP address." ::= {vmGroupInfolistEntry 3 } vmGroupInfoPort OBJECT-TYPE SYNTAX PortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "System port connected to the virtual machine." ::= { vmGroupInfolistEntry 4 } vmGroupInfoGroup OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual machine group." ::= {vmGroupInfolistEntry 5 } vmGroupInfoVlan OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The virtual machine VLAN" ::= {vmGroupInfolistEntry 6 } vmGroupInfoIsESXSvcCon OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Set to 1 if ESX Service Console Interface, else 0." ::= {vmGroupInfolistEntry 7 } vmGroupInfoIsVMK OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Set to 1 if VM Kernel Interface, else 0." ::= {vmGroupInfolistEntry 8 } vmGroupInfoName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Virtual Machine Name, if available." ::= {vmGroupInfolistEntry 9 } vmGroupInfoUUID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Virtual Machine UUID, if available." ::= {vmGroupInfolistEntry 10 } vmGroupInfoVSwitch OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Virtual Machine VSwitch, if available." ::= {vmGroupInfolistEntry 11 } vmGroupInfoPortGroup OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Virtual Machine Port Group, if available." ::= {vmGroupInfolistEntry 12 } vmGroupInfoHost OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Virtual Machine Host, if available." ::= {vmGroupInfolistEntry 13 } -- ---------------------------------------------------------------------------- -- VMReady Information } -- ---------------------------------------------------------------------------- -- ------------------------------------------------------------------------- -- -- Edge Virtual Bridge { -- ------------------------------------------------------------------------- -- -- ---------------------------------------------------------------------------- -- { INSERT: evb -- ---------------------------------------------------------------------------- evbConfig OBJECT IDENTIFIER ::= { evb 1 } evbInfo OBJECT IDENTIFIER ::= { evb 2 } evbOper OBJECT IDENTIFIER ::= { evb 3 } -- ------------------------------------------------------------------------- -- -- EVB Configuration { -- ------------------------------------------------------------------------- -- evbCurCfgProfilesTable OBJECT-TYPE SYNTAX SEQUENCE OF EvbCurCfgProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of EVB Profiles in the current config" ::= { evbConfig 3 } evbCurCfgProfileEntry OBJECT-TYPE SYNTAX EvbCurCfgProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about EVB Profile in current config." INDEX { evbCurCfgProfileIndex } ::= { evbCurCfgProfilesTable 1 } EvbCurCfgProfileEntry ::= SEQUENCE { evbCurCfgProfileIndex Integer32 ,evbCurCfgRR INTEGER ,evbCurCfgVSIDisc INTEGER } evbCurCfgProfileIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the evb profile table." ::= { evbCurCfgProfileEntry 1 } evbCurCfgRR OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable RR on port." ::= { evbCurCfgProfileEntry 2 } evbCurCfgVSIDisc OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enable VSI Discover capability on port." ::= { evbCurCfgProfileEntry 3 } evbNewCfgProfilesTable OBJECT-TYPE SYNTAX SEQUENCE OF EvbNewCfgProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of EVB Profiles in the new config" ::= { evbConfig 4 } evbNewCfgProfileEntry OBJECT-TYPE SYNTAX EvbNewCfgProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about EVB Profile in new config." INDEX { evbNewCfgProfileIndex } ::= { evbNewCfgProfilesTable 1 } EvbNewCfgProfileEntry ::= SEQUENCE { evbNewCfgProfileIndex Integer32 ,evbNewCfgRR INTEGER ,evbNewCfgVSIDisc INTEGER } evbNewCfgProfileIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the evb profile table." ::= { evbNewCfgProfileEntry 1 } evbNewCfgRR OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable RR on port." ::= { evbNewCfgProfileEntry 2 } evbNewCfgVSIDisc OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(0) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable VSI Discover capability on port." ::= { evbNewCfgProfileEntry 3 } evbCurCfgVsidbTable OBJECT-TYPE SYNTAX SEQUENCE OF EvbCurCfgVsidbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of EVB VSI Database server in the current config" ::= { evbConfig 5 } evbCurCfgVsidbEntry OBJECT-TYPE SYNTAX EvbCurCfgVsidbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about EVB VSI Database in current config." INDEX { evbCurCfgVsidbIndex } ::= { evbCurCfgVsidbTable 1 } EvbCurCfgVsidbEntry ::= SEQUENCE { evbCurCfgVsidbIndex Integer32 ,evbCurCfgVsidbMgrIp DisplayString ,evbCurCfgVsidbPort INTEGER ,evbCurCfgVsidbDocpath DisplayString ,evbCurCfgVsidbAlltypes DisplayString ,evbCurCfgVsidbInterval Integer32 ,evbCurCfgVsidbProtocol DisplayString } evbCurCfgVsidbIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the evb vsi database server table." ::= { evbCurCfgVsidbEntry 1 } evbCurCfgVsidbMgrIp OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI DB Manager IP address." ::= { evbCurCfgVsidbEntry 2 } evbCurCfgVsidbPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VSI DB Manager Port." ::= { evbCurCfgVsidbEntry 3 } evbCurCfgVsidbDocpath OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI DB Document Path." ::= { evbCurCfgVsidbEntry 4 } evbCurCfgVsidbAlltypes OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI DB Document File." ::= { evbCurCfgVsidbEntry 5 } evbCurCfgVsidbInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI DB Update Interval in second." ::= { evbCurCfgVsidbEntry 6 } evbCurCfgVsidbProtocol OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI DB Protocol, HTTP or HTTPS." ::= { evbCurCfgVsidbEntry 8 } evbNewCfgVsidbTable OBJECT-TYPE SYNTAX SEQUENCE OF EvbNewCfgVsidbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of EVB VSI Database in the new config" ::= { evbConfig 6 } evbNewCfgVsidbEntry OBJECT-TYPE SYNTAX EvbNewCfgVsidbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about EVB VSI Database in new config." INDEX { evbNewCfgVsidbIndex } ::= { evbNewCfgVsidbTable 1 } EvbNewCfgVsidbEntry ::= SEQUENCE { evbNewCfgVsidbIndex Integer32 ,evbNewCfgVsidbMgrIp DisplayString ,evbNewCfgVsidbPort INTEGER ,evbNewCfgVsidbDocpath DisplayString ,evbNewCfgVsidbAlltypes DisplayString ,evbNewCfgVsidbInterval Integer32 ,evbNewCfgVsidbProtocol DisplayString } evbNewCfgVsidbIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the evb vsi database server table." ::= { evbNewCfgVsidbEntry 1 } evbNewCfgVsidbMgrIp OBJECT-TYPE SYNTAX DisplayString (SIZE(0..40)) MAX-ACCESS read-write STATUS current DESCRIPTION "VSI DB Manager IP address." ::= { evbNewCfgVsidbEntry 2 } evbNewCfgVsidbPort OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "VSI DB Manager Port." ::= { evbNewCfgVsidbEntry 3 } evbNewCfgVsidbDocpath OBJECT-TYPE SYNTAX DisplayString (SIZE(0..127)) MAX-ACCESS read-write STATUS current DESCRIPTION "VSI DB Document Path." ::= { evbNewCfgVsidbEntry 4 } evbNewCfgVsidbAlltypes OBJECT-TYPE SYNTAX DisplayString (SIZE(0..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "VSI DB Document File." ::= { evbNewCfgVsidbEntry 5 } evbNewCfgVsidbInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "VSI DB Update Interval in second, range from 5s to 300s, 0 means disable auto update." ::= { evbNewCfgVsidbEntry 6 } evbNewCfgVsidbProtocol OBJECT-TYPE SYNTAX DisplayString (SIZE(0..5)) MAX-ACCESS read-write STATUS current DESCRIPTION "VSI DB Protocol, HTTP or HTTPS." ::= { evbNewCfgVsidbEntry 8 } -- ------------------------------------------------------------------------- -- -- EVB Configuration (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- EVB Information { -- ------------------------------------------------------------------------- -- vdpTLVInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF VdpTLVInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of associated VDP TLV Info." ::= { evbInfo 1 } vdpTLVInfoEntry OBJECT-TYPE SYNTAX VdpTLVInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about associated VDP TLV." INDEX { vdpTLVInfoEntryIndex } ::= { vdpTLVInfoTable 1 } VdpTLVInfoEntry ::= SEQUENCE { vdpTLVInfoEntryIndex Integer32 ,vdpTLVType Integer32 ,vdpTLVLength Integer32 ,vdpTLVOUI OCTET STRING ,vdpTLVsubType Integer32 ,vdpTLVRequest OCTET STRING ,vdpTLVResp Integer32 ,vdpTLVMgrId Integer32 ,vdpTLVTypeID Integer32 ,vdpTLVInstanceID OCTET STRING ,vdpTLVPort Integer32 ,vdpTLVStag Integer32 ,vdpNumEntry Integer32 ,vdpTLVVlan1 Integer32 ,vdpTLVmac1 OCTET STRING ,vdpTLVVlan2 Integer32 ,vdpTLVmac2 OCTET STRING ,vdpTLVVlan3 Integer32 ,vdpTLVmac3 OCTET STRING ,vdpTLVVlan4 Integer32 ,vdpTLVmac4 OCTET STRING ,vdpTLVVlan5 Integer32 ,vdpTLVmac5 OCTET STRING ,vdpTLVVlan6 Integer32 ,vdpTLVmac6 OCTET STRING ,vdpTLVVlan7 Integer32 ,vdpTLVmac7 OCTET STRING ,vdpTLVVlan8 Integer32 ,vdpTLVmac8 OCTET STRING ,vdpTLVVlan9 Integer32 ,vdpTLVmac9 OCTET STRING ,vdpTLVVlan10 Integer32 ,vdpTLVmac10 OCTET STRING ,vdpTLVVlan11 Integer32 ,vdpTLVmac11 OCTET STRING ,vdpTLVVlan12 Integer32 ,vdpTLVmac12 OCTET STRING } vdpTLVInfoEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the vdp TLV info table." ::= { vdpTLVInfoEntry 1 } vdpTLVType OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV Type info." ::= { vdpTLVInfoEntry 2 } vdpTLVLength OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV Length info." ::= { vdpTLVInfoEntry 3 } vdpTLVOUI OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV OUI info." ::= { vdpTLVInfoEntry 4 } vdpTLVsubType OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV Sub Type info." ::= { vdpTLVInfoEntry 5 } vdpTLVRequest OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV Request info." ::= { vdpTLVInfoEntry 6 } vdpTLVResp OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV Response info." ::= { vdpTLVInfoEntry 7 } vdpTLVMgrId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV Manager ID info." ::= { vdpTLVInfoEntry 8 } vdpTLVTypeID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV Type ID info." ::= { vdpTLVInfoEntry 9 } vdpTLVInstanceID OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV instance ID info." ::= { vdpTLVInfoEntry 10 } vdpTLVPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV port info." ::= { vdpTLVInfoEntry 11 } vdpTLVStag OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV stag info." ::= { vdpTLVInfoEntry 12 } vdpNumEntry OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 13 } vdpTLVVlan1 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 14 } vdpTLVmac1 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 15 } vdpTLVVlan2 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 16 } vdpTLVmac2 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 17 } vdpTLVVlan3 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 18 } vdpTLVmac3 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 19 } vdpTLVVlan4 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 20 } vdpTLVmac4 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 21 } vdpTLVVlan5 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 22 } vdpTLVmac5 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 23 } vdpTLVVlan6 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 24 } vdpTLVmac6 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 25 } vdpTLVVlan7 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 26 } vdpTLVmac7 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 27 } vdpTLVVlan8 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 28 } vdpTLVmac8 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 29 } vdpTLVVlan9 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 30 } vdpTLVmac9 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 31 } vdpTLVVlan10 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 32 } vdpTLVmac10 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 33 } vdpTLVVlan11 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 34 } vdpTLVmac11 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 35 } vdpTLVVlan12 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV vlan info." ::= { vdpTLVInfoEntry 36 } vdpTLVmac12 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The vdp TLV mac info." ::= { vdpTLVInfoEntry 37 } vmsInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF VmsInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of active VM Info." ::= { evbInfo 2 } vmsInfoEntry OBJECT-TYPE SYNTAX VmsInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about active VMs." INDEX { vmsInfoEntryIndex } ::= { vmsInfoTable 1 } VmsInfoEntry ::= SEQUENCE { vmsInfoEntryIndex Integer32 ,vmsInfoTypeId Integer32 ,vmsInfoVersion Integer32 ,vmsInfoMac OCTET STRING ,vmsInfoVlan Integer32 ,vmsInfoPort Integer32 ,vmsInfoTxACL Integer32 ,vmsInfoRxEntry Integer32 ,vmsInfoACLs DisplayString } vmsInfoEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the active VM info table." ::= { vmsInfoEntry 1 } vmsInfoTypeId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI Type ID info of the active VM" ::= { vmsInfoEntry 2 } vmsInfoVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI Type version info of the active VM" ::= { vmsInfoEntry 3 } vmsInfoMac OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI Mac info of the active VM" ::= { vmsInfoEntry 4 } vmsInfoVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI vlan info of the active VM" ::= { vmsInfoEntry 5 } vmsInfoPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI port info of the active VM" ::= { vmsInfoEntry 6 } vmsInfoTxACL OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI Tx ACL info of the active VM" ::= { vmsInfoEntry 7 } vmsInfoRxEntry OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI Rx info of the active VM" ::= { vmsInfoEntry 8 } vmsInfoACLs OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The ACL info of the active VM" ::= { vmsInfoEntry 9 } vsiInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF VsiInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of vsi policy Info." ::= { evbInfo 3 } vsiInfoEntry OBJECT-TYPE SYNTAX VsiInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about vsi policy." INDEX { vsiInfoEntryIndex } ::= { vsiInfoTable 1 } VsiInfoEntry ::= SEQUENCE { vsiInfoEntryIndex Integer32 ,vsiInfoTypeId Integer32 ,vsiInfoVersion Integer32 ,vsiInfoMac OCTET STRING ,vsiInfoVlan Integer32 ,vsiInfoPort Integer32 ,vsiInfoTxACL Integer32 ,vsiInfoRxEntry Integer32 } vsiInfoEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the vsi info table." ::= { vsiInfoEntry 1 } vsiInfoTypeId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI Type ID info" ::= { vsiInfoEntry 2 } vsiInfoVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI Type version info" ::= { vsiInfoEntry 3 } vsiInfoMac OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI Mac Info" ::= { vsiInfoEntry 4 } vsiInfoVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI vlan info" ::= { vsiInfoEntry 5 } vsiInfoPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI port info" ::= { vsiInfoEntry 6 } vsiInfoTxACL OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI Tx ACL info" ::= { vsiInfoEntry 7 } vsiInfoRxEntry OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VSI Rx info" ::= { vsiInfoEntry 8 } vsidbInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF VsidbInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VSI Database Info." ::= { evbInfo 4 } vsidbInfoEntry OBJECT-TYPE SYNTAX VsidbInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about VSI database" INDEX { vsidbInfoEntryIndex } ::= { vsidbInfoTable 1 } VsidbInfoEntry ::= SEQUENCE { vsidbInfoEntryIndex Integer32 ,vsidbInfoName DisplayString ,vsidbInfoTypeId Integer32 ,vsidbInfoVersion Integer32 ,vsidbInfoManagerId Integer32 ,vsidbInfoVlanIds DisplayString ,vsidbInfoTxRate Integer32 ,vsidbInfoTxBurst Integer32 ,vsidbInfoRxRate Integer32 ,vsidbInfoRxBurst Integer32 } vsidbInfoEntryIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the VSI Database table." ::= { vsidbInfoEntry 1 } vsidbInfoName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Name." ::= { vsidbInfoEntry 2 } vsidbInfoTypeId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Type Id." ::= { vsidbInfoEntry 3 } vsidbInfoVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Version." ::= { vsidbInfoEntry 4 } vsidbInfoManagerId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Manager Id." ::= { vsidbInfoEntry 5 } vsidbInfoVlanIds OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database VLAN List." ::= { vsidbInfoEntry 6 } vsidbInfoTxRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Transmit Rate." ::= { vsidbInfoEntry 7 } vsidbInfoTxBurst OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Transmit Burst." ::= { vsidbInfoEntry 8 } vsidbInfoRxRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Receive Rate." ::= { vsidbInfoEntry 9 } vsidbInfoRxBurst OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Receove Burst." ::= { vsidbInfoEntry 10 } vsidbAclInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF VsidbAclInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of VSI Database ACLs Info." ::= { evbInfo 5 } vsidbAclInfoEntry OBJECT-TYPE SYNTAX VsidbAclInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about VSI database" INDEX { vsidbAclInfoEntryDbIndex, vsidbAclInfoEntryAclIndex } ::= { vsidbAclInfoTable 1 } VsidbAclInfoEntry ::= SEQUENCE { vsidbAclInfoEntryDbIndex Integer32, vsidbAclInfoEntryAclIndex Integer32 ,vsidbAclInfoTypeId Integer32 ,vsidbAclInfoVersion Integer32 ,vsidbAclInfoManagerId Integer32 ,vsidbAclInfoSrcMACAddress DisplayString ,vsidbAclInfoSrcMACMask DisplayString ,vsidbAclInfoDstMACAddress DisplayString ,vsidbAclInfoDstMACMask DisplayString ,vsidbAclInfoVlanId INTEGER -- ,vsidbAclInfoVlanMask DisplayString -- ,vsidbAclInfo8021pPriority DisplayString ,vsidbAclInfoEthernetType DisplayString ,vsidbAclInfoSrcIPAddress IpAddress ,vsidbAclInfoSrcIPMask IpAddress ,vsidbAclInfoDstIPAddress IpAddress ,vsidbAclInfoDstIPMask IpAddress ,vsidbAclInfoTypeOfService DisplayString ,vsidbAclInfoProtocol DisplayString ,vsidbAclInfoTCPFlags DisplayString ,vsidbAclInfoTCPFlagsMask DisplayString ,vsidbAclInfoSrcPort INTEGER ,vsidbAclInfoSrcPortMask DisplayString ,vsidbAclInfoDstPort INTEGER ,vsidbAclInfoDstPortMask DisplayString ,vsidbAclInfoAction DisplayString ,vsidbAclInfoNewPrio DisplayString } vsidbAclInfoEntryDbIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the VSI Database table." ::= { vsidbAclInfoEntry 1 } vsidbAclInfoEntryAclIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the VSI Database ACLs table." ::= { vsidbAclInfoEntry 2 } vsidbAclInfoTypeId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Type Id." ::= { vsidbAclInfoEntry 3 } vsidbAclInfoVersion OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Version." ::= { vsidbAclInfoEntry 4 } vsidbAclInfoManagerId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database Manager Id." ::= { vsidbAclInfoEntry 5 } vsidbAclInfoSrcMACAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Source MAC address." ::= { vsidbAclInfoEntry 6 } vsidbAclInfoSrcMACMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Source MAC address mask." ::= { vsidbAclInfoEntry 7 } vsidbAclInfoDstMACAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Destination MAC address." ::= { vsidbAclInfoEntry 8 } vsidbAclInfoDstMACMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Destination MAC address mask." ::= { vsidbAclInfoEntry 9 } vsidbAclInfoVlanId OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Virtual LAN value." ::= { vsidbAclInfoEntry 10 } -- vsidbAclInfoVlanMask OBJECT-TYPE -- SYNTAX DisplayString -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "VSI Database ACL Virtual LAN mask." -- ::= { vsidbAclInfoEntry 11 } -- vsidbAclInfo8021pPriority OBJECT-TYPE -- SYNTAX DisplayString -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "VSI Database ACL 802.1p priotiry, -- 'none' for not initialised, -- within the ranger 0-7." -- ::= { vsidbAclInfoEntry 12 } vsidbAclInfoEthernetType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Ethernet type value, 'none' for not initialised, within the ranger 1536-65535." ::= { vsidbAclInfoEntry 13 } vsidbAclInfoSrcIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Source IP Address, only available when EthernetType is IPv4(0x0800)." ::= { vsidbAclInfoEntry 14 } vsidbAclInfoSrcIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Source IP Address mask, only available when EthernetType is IPv4(0x0800)." ::= { vsidbAclInfoEntry 15 } vsidbAclInfoDstIPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Destination IP Address, only available when EthernetType is IPv4(0x0800)." ::= { vsidbAclInfoEntry 16 } vsidbAclInfoDstIPMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Destination IP Address mask, only available when EthernetType is IPv4(0x0800)." ::= { vsidbAclInfoEntry 17 } vsidbAclInfoTypeOfService OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Type Of Service value, only available when EthernetType is IPv4(0x0800), 'none' for not initialised, within the ranger 0-255." ::= { vsidbAclInfoEntry 18 } vsidbAclInfoProtocol OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL IP protocol, only available when EthernetType is IPv4(0x0800), 'none' for not initialised, within the ranger 0-255." ::= { vsidbAclInfoEntry 19 } vsidbAclInfoTCPFlags OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL TCP Flags value, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6)." ::= { vsidbAclInfoEntry 20 } vsidbAclInfoTCPFlagsMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL TCP Flags mask, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6)." ::= { vsidbAclInfoEntry 21 } vsidbAclInfoSrcPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Source TCP/UDP Port value, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6) or UDP(17)." ::= { vsidbAclInfoEntry 22 } vsidbAclInfoSrcPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Source TCP/UDP Port mask, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6) or UDP(17)." ::= { vsidbAclInfoEntry 23 } vsidbAclInfoDstPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Destination TCP/UDP Port value, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6) or UDP(17)." ::= { vsidbAclInfoEntry 24 } vsidbAclInfoDstPortMask OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Destination TCP/UDP Port mask, only available when EthernetType is IPv4(0x0800) and Protocol is TCP(6) or UDP(17)." ::= { vsidbAclInfoEntry 25 } vsidbAclInfoAction OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL Action" ::= { vsidbAclInfoEntry 26 } vsidbAclInfoNewPrio OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "VSI Database ACL New Pirority value, only available when Action includes 'setpriority', 'none' for not initialised." ::= { vsidbAclInfoEntry 27 } -- ------------------------------------------------------------------------- -- -- EVB Information (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- EVB Operation { -- ------------------------------------------------------------------------- -- evbVsidbOper OBJECT-TYPE SYNTAX INTEGER { ok(1), update(2), clean(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to 'update(2)', it downloads the xml file from VSIDB server and update local VSI database; when set to 'clean(3)', it cleans local VSI database; 'ok(1)' is returned when the object is read." ::= { evbOper 1 } evbAssocVsiClean OBJECT-TYPE SYNTAX INTEGER { ok(1), clean(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When set to 'clean(2)', it cleans all associated VSIs; 'ok(1)' is returned when the object is read." ::= { evbOper 2 } -- ------------------------------------------------------------------------- -- -- EVB Operation (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- Edge Virtual Bridge (end) } -- ------------------------------------------------------------------------- -- -- ------------------------------------------------------------------------- -- -- VMReady Miscellaneous Configuration { -- ------------------------------------------------------------------------- -- vmReadyLocalAdmMac OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Treat locally administred MAC address as VMs" ::= { vmReadyMisc 1 } vmReadyCurCfgOuiTbl OBJECT-TYPE SYNTAX SEQUENCE OF VMReadyCurCfgOuiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of current VM Ready OUI configuration." ::= { vmReadyMisc 2 } vmReadyCurCfgOuiEntry OBJECT-TYPE SYNTAX VMReadyCurCfgOuiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the current VM Ready OUI table." INDEX { vmReadyCurCfgOuiMacIdx } ::= { vmReadyCurCfgOuiTbl 1 } VMReadyCurCfgOuiEntry ::= SEQUENCE { vmReadyCurCfgOuiMacIdx Unsigned32, vmReadyCurCfgOuiMac PhysAddress, vmReadyCurCfgVendor DisplayString } vmReadyCurCfgOuiMacIdx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "OUI of locally administred MAC address" ::= { vmReadyCurCfgOuiEntry 1 } vmReadyCurCfgOuiMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "OUI of locally administred MAC address" ::= { vmReadyCurCfgOuiEntry 2 } vmReadyCurCfgVendor OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor name of the OUI locally administred" ::= { vmReadyCurCfgOuiEntry 3 } vmReadyNewCfgOuiTbl OBJECT-TYPE SYNTAX SEQUENCE OF VMReadyNewCfgOuiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of new VM Ready OUI configuration." ::= { vmReadyMisc 3 } vmReadyNewCfgOuiEntry OBJECT-TYPE SYNTAX VMReadyNewCfgOuiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the new VM Ready OUI table." INDEX { vmReadyNewCfgOuiMacIdx } ::= { vmReadyNewCfgOuiTbl 1 } VMReadyNewCfgOuiEntry ::= SEQUENCE { vmReadyNewCfgOuiMacIdx Unsigned32, vmReadyNewCfgOuiMac DisplayString, vmReadyNewCfgVendor DisplayString, vmReadyNewCfgDelete INTEGER } vmReadyNewCfgOuiMacIdx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "OUI of locally administred MAC address" ::= { vmReadyNewCfgOuiEntry 1 } vmReadyNewCfgOuiMac OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "New OUI of locally administred MAC address Format xx:yy:zz " ::= { vmReadyNewCfgOuiEntry 2 } vmReadyNewCfgVendor OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Vendor name of the OUI locally administred" ::= { vmReadyNewCfgOuiEntry 3 } vmReadyNewCfgDelete OBJECT-TYPE SYNTAX INTEGER { other(0), delete(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "If set the OUI of the locally administred MAC would be deleted" ::= { vmReadyNewCfgOuiEntry 4 } -- ------------------------------------------------------------------------- -- -- VMReady Miscellaneous Configuration(end) } -- ------------------------------------------------------------------------- -- -- ---------------------------------------------------------------------------- -- } INSERT: virt -- ---------------------------------------------------------------------------- -- ---------------------------------------------------------------------------- -- } INSERT: bntRoot -- ---------------------------------------------------------------------------- -- Access Switch for Blade OS TOR Private MIBs -- tor-BladeSwitch OBJECT IDENTIFIER ::= { blade 100 } -- MIB definitions for Standalone BNT Private MIBs -- Access "productID" group for Common Standalone BNT Private MIBs ibmnos-BladeSwitch OBJECT IDENTIFIER ::= { blade 100 } ibmnoscfa OBJECT IDENTIFIER ::= { ibmnos-BladeSwitch 27 } -- ---------------------------------------------------------------------------- -- { INSERT: cfa -- ---------------------------------------------------------------------------- if OBJECT IDENTIFIER ::= { ibmnoscfa 1 } -- ifMainTable -- This table is used for the management of all the interfaces in the -- system. ifMainTable OBJECT-TYPE SYNTAX SEQUENCE OF IfMainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of all the interface entries in the system. This table contains objects which are applicable to all types of interfaces in the system. This table is a proprietary extension to the standard ifTable and ifXTable. The index to this table has the semantics of the MIB-2 ifIndex." ::= { if 4 } ifMainEntry OBJECT-TYPE SYNTAX IfMainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing management information applicable to a particular interface." INDEX { ifMainIndex } ::= { ifMainTable 1 } IfMainEntry ::= SEQUENCE { ifMainIndex InterfaceIndex, ifMainPortName DisplayString } ifMainIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique value, greater than zero, for each interface. This object is identical to the ifIndex of the standard MIB-2 ifTable." ::= { ifMainEntry 1 } ifMainPortName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This is used to assign a alias to a port" ::= { ifMainEntry 9 } -- ---------------------------------------------------------------------------- -- } INSERT: cfa -- ---------------------------------------------------------------------------- ibmnos OBJECT IDENTIFIER ::= { ibmnos-BladeSwitch 81 } -- ---------------------------------------------------------------------------- -- { INSERT: bos -- ---------------------------------------------------------------------------- -- ==================================================================== -- groups in the MIB -- ==================================================================== ibmnosSystem OBJECT IDENTIFIER ::= { ibmnos 1 } ibmnosConfigControl OBJECT IDENTIFIER ::= { ibmnos 2 } -- ==================================================================== -- System Group -- Configurtion Save related configuration / information ibmnosConfigSaveOption OBJECT-TYPE SYNTAX INTEGER { noSave(1), flashSave(2), remoteTftpSave(3), startupConfig(4), backupConfig(5), remoteTftpRestore(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether the configurations of the switch has to be saved or not. The value 'noSave' specifies that the configurations need not be saved. The value 'flashSave' specifies that the configurations need to be saved in flash in the specified file name issConfigSaveFileName. The value 'remoteSave' specifies that the configurations need to be saved in specified remote system. The value 'startupConfig' specifies that the configurations need to be saved in flash in the 'Startup Configuration File'. The value 'backupConfig' specifies that the configurations need to be saved in flash in the 'backup Configuration File'. The value 'remoteTftpRestore' specifies that the configurations need to be restored from remote system and saved in the file as indicated by 'ibmnosConfigRemoteType'. This configuration are copied to configuration blocks and applied after restart." DEFVAL { noSave } ::= { ibmnosSystem 10 } ibmnosConfigSaveFileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "Name of the file in which the switch configurations are to be saved. This object is valid only if 'issConfigSaveOption' is chosen to be 'flashSave' or 'remoteSave'." DEFVAL { "iss.conf" } ::= { ibmnosSystem 12 } ibmnosInitiateConfigSave OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When set as 'true' switch configurations save operation is initiated. As soon as the configuration save operation is completed, the value of this object reverts back to 'false'. All the configurations made via the three interfaces viz. -> commandline interface -> Web Interface -> SNMP interface are saved either in 'Startup Configuration File' in the flash or in the specified 'issConfigSaveFileName' in the flash or in the chosen remote system, depending upon 'ConfigSaveOption'." DEFVAL { false } ::= { ibmnosSystem 13 } ibmnosConfigSaveStatus OBJECT-TYPE SYNTAX INTEGER { saveInProgress(1), saveSuccessful(2), saveFailed(3), notInitiated(4), saveNotRequired(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of configuration save operation." DEFVAL { notInitiated } ::= { ibmnosSystem 14 } ibmnosConfigRestoreOption OBJECT-TYPE SYNTAX INTEGER { factory(1), activeConfig(2), backupConfig(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether the switch configurations have to be restored or not. The value 'factory' specifies that the switch configurations need not be restored when the system is restarted. The value 'activeConfig' specifies that the configurations need to be restored from the 'Startup Configuration File' in the flash when the system is restarted. The value 'backupConfig' specifies that the configurations need to be restored from the 'Backup Configuration File' in the flash when the system is restarted." DEFVAL { factory } ::= { ibmnosSystem 15 } ibmnosLoggingOption OBJECT-TYPE SYNTAX INTEGER { console(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Logging option specifying whether the logging is to be done at console or to a file(system buffer) in the system." ::= { ibmnosSystem 26 } -- Login Authentication mechanism ibmnosLoginAuthentication OBJECT-TYPE SYNTAX INTEGER { local(1), remoteRadius(2), remoteTacacs(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The mechanism by which the user login to access the GUI for configuration has to be authenticated. Authentication is done either locally or in the remote side through a RADIUS Server." ::= { ibmnosSystem 32 } ibmnosConfigRestoreFileVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(1..12)) MAX-ACCESS read-only STATUS current DESCRIPTION "Config Restoration file version. This version will be compared in each reboot against version stored in restoration file. Restoration will occur only if the first field in restoration file is this OID and the RestoreFileVersion value also matches." ::= { ibmnosSystem 40 } -- Config Control Group -- Port Control Table ibmnosPortCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmnosPortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table to control the port specific parameters of the device like speed, duplex mode, etc." ::= { ibmnosConfigControl 2 } ibmnosPortCtrlEntry OBJECT-TYPE SYNTAX IbmnosPortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry appears in this table for each interface in the system. Index to the table is the interface index of the port." INDEX { ibmnosPortCtrlIndex } ::= { ibmnosPortCtrlTable 1 } IbmnosPortCtrlEntry ::= SEQUENCE { ibmnosPortCtrlIndex Integer32, ibmnosPortCtrlMode INTEGER, ibmnosPortCtrlDuplex INTEGER, ibmnosPortCtrlSpeed INTEGER, ibmnosPortCtrlFlowControl INTEGER } ibmnosPortCtrlIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Interface index of the port for which the configuration in this entry applies." ::= { ibmnosPortCtrlEntry 1 } ibmnosPortCtrlMode OBJECT-TYPE SYNTAX INTEGER { auto (1), noNegotiation (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Speficies the mode in which the speed, duplex modes and flow control of the interface is determined. If set as 'auto', the hardware senses speed and negotiates with the port on the other end of the link for data transfer operation as 'full-duplex' or 'half-duplex' and about flow contol. If set as 'nonegotiation', the configured values for interface speed, duplex mode and flow control will be effective." DEFVAL { auto } ::= { ibmnosPortCtrlEntry 2 } ibmnosPortCtrlDuplex OBJECT-TYPE SYNTAX INTEGER { full (1), half (2), any (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures interface data transfer mode as full-duplex or half-duplex. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value 'any'" ::= { ibmnosPortCtrlEntry 3 } ibmnosPortCtrlSpeed OBJECT-TYPE SYNTAX INTEGER { tenMBPS (1), hundredMBPS (2), oneGB (3), tenGB (4), any (5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configures interface speed. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value 'any'" ::= { ibmnosPortCtrlEntry 4 } ibmnosPortCtrlFlowControl OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2), send (3), receive (4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables / disables flow control for the interface. This object be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negotiating with its peer" ::= { ibmnosPortCtrlEntry 5 } -- ---------------------------------------------------------------------------- -- } INSERT: bos -- ---------------------------------------------------------------------------- toraddon OBJECT IDENTIFIER ::= { ibmnos-BladeSwitch 100 } -- ---------------------------------------------------------------------------- -- { INSERT: toraddon -- ---------------------------------------------------------------------------- -- Module Group --vlan OBJECT IDENTIFIER ::= { toraddon 1 } cfa OBJECT IDENTIFIER ::= { toraddon 2 } sys OBJECT IDENTIFIER ::= { toraddon 7 } ibmnosFdb OBJECT IDENTIFIER ::= { toraddon 13 } tor-switch OBJECT IDENTIFIER ::= { toraddon 14 } ibmnosBladeHarmony OBJECT IDENTIFIER ::= { toraddon 17 } -- Blade Harmony Wrapper Objects (bosBladeHarmony) dataCollection OBJECT IDENTIFIER ::= { ibmnosBladeHarmony 1 } imageConfigTransfer OBJECT IDENTIFIER ::= { ibmnosBladeHarmony 3 } ibmnosFdbTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmnosFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of FDB entries." ::= { ibmnosFdb 5 } ibmnosFdbEntry OBJECT-TYPE SYNTAX IbmnosFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the FDB table" INDEX { ibmnosFdbVlan, ibmnosFdbMacAddr } ::= { ibmnosFdbTable 1 } IbmnosFdbEntry ::= SEQUENCE { ibmnosFdbVlan Integer32, ibmnosFdbMacAddr PhysAddress, ibmnosFdbMacAddrStr DisplayString, ibmnosFdbVlanId Integer32, ibmnosFdbSrcPort Integer32, ibmnosFdbSrcTrunk Integer32, ibmnosFdbState INTEGER, ibmnosFdbStatus Integer32, ibmnosFdbClearMac INTEGER } ibmnosFdbVlan OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID for the FDB entry." ::= { ibmnosFdbEntry 1 } ibmnosFdbMacAddr OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MAC address for the FDB entry." ::= { ibmnosFdbEntry 2 } ibmnosFdbMacAddrStr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address in hex format for the FDB entry. This node is added for display purpose." ::={ ibmnosFdbEntry 3 } ibmnosFdbVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID for the FDB entry. This node is added for display purpose." ::= { ibmnosFdbEntry 4 } ibmnosFdbSrcPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Either the value '0', or the port number of the port on which a frame having a source address equal to the value of the corresponding instance has been seen. A value of '0' indicates that the port number has not been learned but that the bridge does have some forwarding/filtering information about this address." ::= { ibmnosFdbEntry 5 } ibmnosFdbSrcTrunk OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Either the value '0', or the trunk number of the trunk on which a frame having a source address equal to the value of the corresponding instance has been seen. A value of '0' indicates that the source address is not associated with a trunk." ::= { ibmnosFdbEntry 6 } ibmnosFdbState OBJECT-TYPE SYNTAX INTEGER { unknown(1), forward(2), trunk(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the FDB entry. The meanings of the values are : unknown(1) : the MAC address has not yet been learned by the switch but has only been seen as a destination address forward(2) : the MAC address has been learned by the switch trunk(3) : frames with this MAC address are forwarded to trunk group" ::= { ibmnosFdbEntry 7 } ibmnosFdbStatus OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "'1' if it is permanent '0' if it is not permanent" ::= { ibmnosFdbEntry 10 } ibmnosFdbClearMac OBJECT-TYPE SYNTAX INTEGER { ok(1), clear(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to clear(2) clears the corresponding table entry in FDB." ::= { ibmnosFdbEntry 11 } -- Interface mangager(CFA) objects ibmnosPortCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmnosPortCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of port configuration in the new_configuration block." ::= { cfa 1 } ibmnosPortCfgTableEntry OBJECT-TYPE SYNTAX IbmnosPortCfgTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the port configuration table in the new_configuration block." INDEX {ibmnosPortCfgIndx } ::= {ibmnosPortCfgTable 1 } IbmnosPortCfgTableEntry ::= SEQUENCE { ibmnosPortCfgIndx Integer32, ibmnosPortCfgVlanTag INTEGER } ibmnosPortCfgIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the row in port configurations table." ::= { ibmnosPortCfgTableEntry 1 } ibmnosPortCfgVlanTag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "VLAN tag configured for the port" ::= { ibmnosPortCfgTableEntry 2 } agImageForNextReset OBJECT-TYPE SYNTAX INTEGER{ image1(2), image2(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The software image to be booted from at next reset. The following values are writable: image1(2)...image 1 image2(3)...image 2" ::= { sys 2 } --- Switch Objects hardwarePartNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The hardware part number of the Blade Switch." ::= { tor-switch 1 } hardwareRevision OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The hardware revision. If the revision is not available, a zero length string should be returned." ::= { tor-switch 2 } hardwareLastBoot OBJECT-TYPE SYNTAX INTEGER { unkownReason(0), powerCycle(1), resetFromConsole(2), resetFromTelnetOrSSH(3), resetFromSNMP(4), resetFromWEBUI(5), resetFromScheduled(6), resetFromWatchdogTimer(7), resetFromSWPANIC(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Reason of the last boot. " ::= { tor-switch 3 } hardwareMACAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address." ::= { tor-switch 4 } hardwareSwitchRunningSwVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch software version." ::= { tor-switch 5 } hardwareFlashConfiguration OBJECT-TYPE SYNTAX INTEGER { factory(0), active(1), backup(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The active flash configuration." ::= { tor-switch 6 } hardwarePCBAPartNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The PCBA part number." ::= { tor-switch 7 } hardwareFABNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "FAB Number" ::= { tor-switch 8 } hardwareSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch serial number." ::= { tor-switch 9 } hardwareManufacturingDate OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The date of manufacturing." ::= { tor-switch 10 } hwTemperatureSensor1 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 1." ::= { tor-switch 11 } hwTemperatureSensor2 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 2." ::= { tor-switch 12 } hwTemperatureSensor3 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 3." ::= { tor-switch 13 } hwFan1RPMValue OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Fan 1 RPM value." ::= { tor-switch 14 } hwFan2RPMValue OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Fan 2 RPM value." ::= { tor-switch 15 } hwFan3RPMValue OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Fan 3 RPM value." ::= { tor-switch 16 } hwFan4RPMValue OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Fan 4 RPM value." ::= { tor-switch 17 } hwFan5RPMValue OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Fan 5 RPM value." ::= { tor-switch 18 } hwBoardRevision OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Board revision number." ::= { tor-switch 19 } hwPowerSupply1State OBJECT-TYPE SYNTAX INTEGER { off(0), on(1), absent(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Power Supply 1 state." ::= { tor-switch 20 } hwPowerSupply2State OBJECT-TYPE SYNTAX INTEGER { off(0), on(1), absent(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Power Supply 2 state." ::= { tor-switch 21 } ibmnosSfpInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF IbmnosSfpInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of external port SFP information." ::= { tor-switch 22 } ibmnosSfpInfoTableEntry OBJECT-TYPE SYNTAX IbmnosSfpInfoTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the external port SFP information table." INDEX { ibmnosSfpInfoIndx } ::= { ibmnosSfpInfoTable 1 } IbmnosSfpInfoTableEntry ::= SEQUENCE { ibmnosSfpInfoIndx Integer32, ibmnosSfpInfoDescription INTEGER, ibmnosSfpInfoSerialNumber DisplayString, ibmnosSfpInfoPartNumber DisplayString, ibmnosSfpInfoHWRevision DisplayString } ibmnosSfpInfoIndx OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Sfp Info index (port number)" ::= { ibmnosSfpInfoTableEntry 1 } ibmnosSfpInfoDescription OBJECT-TYPE SYNTAX INTEGER { none(0), sfp(1), cx4(2), sfpplus(3), dac(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Type Ethernet device (None(0), SFP(1), CX4(2), SFPplus(3), DAC(6))" ::= { ibmnosSfpInfoTableEntry 2 } ibmnosSfpInfoSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Serial Number." ::= { ibmnosSfpInfoTableEntry 3 } ibmnosSfpInfoPartNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Part Number." ::= { ibmnosSfpInfoTableEntry 4 } ibmnosSfpInfoHWRevision OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Hardware Revision" ::= { ibmnosSfpInfoTableEntry 5 } swImage1Version OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Software image1 version" ::= { tor-switch 24 } swImage2Version OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Software image2 version" ::= { tor-switch 25 } swBootVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "Software boot version" ::= { tor-switch 26 } hwFan6RPMValue OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Fan 6 RPM value." ::= { tor-switch 27 } hwTemperatureSensor4 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 4." ::= { tor-switch 32 } hwTemperatureSensor5 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 5." ::= { tor-switch 33 } hwTemperatureSensor6 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 4." ::= { tor-switch 34 } hwTemperatureSensor7 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 7." ::= { tor-switch 35 } hwTemperatureSensor8 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 8." ::= { tor-switch 36 } hwTemperatureSensor9 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 9." ::= { tor-switch 37 } hwTemperatureSensor10 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 10." ::= { tor-switch 38 } hwTemperatureSensor11 OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The temperature sensor 11." ::= { tor-switch 39 } hwFan7RPMValue OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Fan 7 RPM value." ::= { tor-switch 40 } hwFan8RPMValue OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Fan 8 RPM value." ::= { tor-switch 41 } hwBootTime OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The hardware system boot time ." ::= { tor-switch 42 } -- Similar to ifAvailableIndex ibmnosPortTableMaxEnt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the port configuration host table." ::= { dataCollection 1 } -- Similar to swImage1Version ibmnosImage1Ver OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the software image stored in image 1 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available or there is no valid software image." ::= { dataCollection 3 } -- Similar to swImage2Version ibmnosImage2Ver OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the software image stored in image 2 storage in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available or there is no valid software image." ::= { dataCollection 4 } hwSwitchSoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch software version." ::= { dataCollection 5 } -- Similar to hwSerialNumber hwSerialNum OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The switch serial number." ::= { dataCollection 6 } -- Already addedd with different data type. --hwLastBoot OBJECT-TYPE -- SYNTAX DisplayString (SIZE(0..48)) -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "Time and reason of the last boot." -- ::= { ibmnosBladeHarmony 7} hwManufacturingDate OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "The date of manufacturing." ::= { dataCollection 7 } -- Similar to issRestart ibmnosReset OBJECT-TYPE SYNTAX INTEGER { other(1), reset(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is an action object to reboot the agent. other(1) is returned always when read." ::= { dataCollection 8 } -- Similar to swBootVersion ibmnosBootVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the boot code in the form of 'major.minor.bugfix'. A zero length string is returned if version is not available." ::= { dataCollection 9 } --Similar to ibmnosConfigRestoreOption ibmnosConfigForNxtReset OBJECT-TYPE SYNTAX INTEGER { active(2), backup(3), default(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The configuration information to be loaded from at next reset. The following values are writable: active(2)...active configuration block backup(3)...backup configuration block default(4)..default configuration block" ::= { dataCollection 10 } ibmnosSoftwareVersion OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the software image that is currently running on the system in the form of 'major.minor.maintenance.bugfix'. A zero length string is returned if version is not available." ::= { dataCollection 11 } agTftpServer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..128)) MAX-ACCESS read-write STATUS current DESCRIPTION "The TFTP server IP address or domain name." ::= { imageConfigTransfer 1 } -- ---------------------------------------------------------------------------- -- } INSERT: g8000 -- ---------------------------------------------------------------------------- -- ---------------------------------------------------------------------------- -- } INSERT: blade -- ---------------------------------------------------------------------------- END