-- ========================================================================== -- Copyright (C) 2002 by HUAWEI TECHNOLOGIES. All rights reserved. -- -- Description: The purpose of this MIB file is to provide the define of -- Terminal Server MIB of HUAWEI quidway serial router. -- Reference: -- Version: V1.0 -- History: -- -- ========================================================================== HUAWEI-TS-MIB DEFINITIONS ::= BEGIN IMPORTS DisplayString FROM RFC1213-MIB IpAddress FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215 huawei,mlsr FROM HUAWEI-3COM-OID-MIB; terminalServer OBJECT IDENTIFIER ::= { mlsr 1 } --routerMemory OBJECT-TYPE -- SYNTAX INTEGER -- ACCESS read-only -- STATUS mandatory -- DESCRIPTION -- "Memory value of the router." -- ::= { router 1 } EntryStatus ::= INTEGER { valid(1), createRequest(2), underCreation(3), invalid(4) } -- The status of a table entry. -- -- Setting this object to the value invalid(4) has the -- effect of invalidating the corresponding entry. -- That is, it effectively disassociates the mapping -- identified with said entry. -- It is an implementation-specific matter as to whether -- the agent removes an invalidated entry from the table. -- Accordingly, management stations must be prepared to -- receive tabular information from agents that -- corresponds to entries currently not in use. Proper -- interpretation of such entries requires examination -- of the relevant EntryStatus object. -- -- An existing instance of this object cannot be set to -- createRequest(2). This object may only be set to -- createRequest(2) when this instance is created. When -- this object is created, the agent may wish to create -- supplemental object instances with default values -- to complete a conceptual row in this table. Because -- the creation of these default objects is entirely at -- the option of the agent, the manager must not assume -- that any will be created, but may make use of any that -- are created. Immediately after completing the create -- operation, the agent must set this object to -- underCreation(3). -- -- When in the underCreation(3) state, an entry is -- allowed to exist in a possibly incomplete, possibly -- inconsistent state, usually to allow it to be -- modified in mutiple PDUs. When in this state, an -- entry is not fully active. Entries shall exist in -- the underCreation(3) state until the management -- station is finished configuring the entry and sets -- this object to valid(1) or aborts, setting this -- object to invalid(4). If the agent determines that -- an entry has been in the underCreation(3) state for -- an abnormally long time, it may decide that the -- management station has crashed. If the agent makes -- this decision, it may set this object to invalid(4) -- to reclaim the entry. A prudent agent will -- understand that the management station may need to -- wait for human input and will allow for that -- possibility in its determination of this abnormally -- long period. -- -- An entry in the valid(1) state is fully configured and -- consistent and fully represents the configuration or -- operation such a row is intended to represent. For -- example, it could be a statistical function that is -- configured and active, or a filter that is available -- in the list of filters processed by the packet capture -- process. -- -- A manager is restricted to changing the state of an -- entry in the following ways: -- -- create under -- To: valid Request Creation invalid -- From: -- valid OK NO OK OK -- createRequest N/A N/A N/A N/A -- underCreation OK NO OK OK -- invalid NO NO NO OK -- nonExistent NO OK NO OK -- -- In the table above, it is not applicable to move the -- state from the createRequest state to any other -- state because the manager will never find the -- variable in that state. The nonExistent state is -- not a value of the enumeration, rather it means that -- the entryStatus variable does not exist at all. -- -- An agent may allow an entryStatus variable to change -- state in additional ways, so long as the semantics -- of the states are followed. This allowance is made -- to ease the implementation of the agent and is made -- despite the fact that managers should never -- excercise these additional state transitions. -- Types -- xxx INTEGER ::= 1 tsAppTable OBJECT-TYPE SYNTAX SEQUENCE OF TSAppEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing how to set the application." ::= { terminalServer 1 } tsAppEntry OBJECT-TYPE SYNTAX TSAppEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Management information about how to set the application." INDEX { tsAppID } ::= { tsAppTable 1 } TSAppEntry ::= SEQUENCE { tsAppID INTEGER, tsAppIPAddress IpAddress, tsAppPort INTEGER, tsAppType INTEGER, tsAppName DisplayString, tsAppSourceIP IpAddress, tsAppLocalPort INTEGER, tsAppTtyServerState INTEGER, tsAppSocketRecvBufSize INTEGER, tsAppSocketSendBufSize INTEGER, tsAppSockRecvByte INTEGER, tsAppSockSendByte INTEGER, tsAppLastRecvTime DisplayString, tsAppLastSendTime DisplayString, tsAppClearStatistic INTEGER, tsAppUnixIndex INTEGER, tsAppStatus EntryStatus } tsAppID OBJECT-TYPE SYNTAX INTEGER(0..515) ACCESS read-only STATUS mandatory DESCRIPTION "Set the ID of application." ::= { tsAppEntry 1 } tsAppIPAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Set the IP Address of UNIX that offer terminal server,0 indicate no ip address." DEFVAL {0} ::= { tsAppEntry 2 } tsAppPort OBJECT-TYPE SYNTAX INTEGER(0|1025..65535) ACCESS read-write STATUS mandatory DESCRIPTION "Set the port of application,0 indicate no port." DEFVAL {0} ::= { tsAppEntry 3 } tsAppType OBJECT-TYPE SYNTAX INTEGER{ normal(1), special(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set the type of application." DEFVAL {normal} ::= { tsAppEntry 4 } tsAppName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..18)) ACCESS read-write STATUS mandatory DESCRIPTION "Set the name of application." ::= { tsAppEntry 5 } tsAppSourceIP OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Set the tcp/ip that will be bound,0 indicate no source ip." DEFVAL {0} ::= { tsAppEntry 6 } tsAppLocalPort OBJECT-TYPE SYNTAX INTEGER(1025..65535|0) ACCESS read-only STATUS mandatory DESCRIPTION "Display the port of router,0 indicate no port." ::= { tsAppEntry 7 } tsAppTtyServerState OBJECT-TYPE SYNTAX INTEGER{ noset(1), kept(2), linking(3), linked(4), removed(5), overcast(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Display the connection-state on the UNIX." ::= { tsAppEntry 8 } tsAppSocketRecvBufSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the size of recvbuf for socket." ::= { tsAppEntry 9 } tsAppSocketSendBufSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the size of sendbuf for socket." ::= { tsAppEntry 10 } tsAppSockRecvByte OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the byte number that has already received from socket." ::= { tsAppEntry 11 } tsAppSockSendByte OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the byte number that has already sent from socket." ::= { tsAppEntry 12 } tsAppLastRecvTime OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Display the time when the tty received from socket for last time." ::= { tsAppEntry 13 } tsAppLastSendTime OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Display the time when the tty sent from socket for last time." ::= { tsAppEntry 14 } tsAppClearStatistic OBJECT-TYPE SYNTAX INTEGER{ clear(1) } ACCESS write-only STATUS mandatory DESCRIPTION "Clear APP's statistic information." ::= { tsAppEntry 15 } tsAppUnixIndex OBJECT-TYPE SYNTAX INTEGER(0..511) ACCESS read-only STATUS mandatory DESCRIPTION "Display the channel number." ::= { tsAppEntry 16 } tsAppStatus OBJECT-TYPE SYNTAX EntryStatus ACCESS read-write STATUS mandatory DESCRIPTION "set the state on terminal server.If you will create a row,the values of tsAppIPAddress,tsAppPort,tsAppType,tsAppName must be not null. You can delete a exist row and you can modify a exist row.If you modify a row under the status of row,you change the status from valid to undercreation.when you have changed them,you change the status to valid" ::= { tsAppEntry 17 } tsAsyModeTtyTable OBJECT-TYPE SYNTAX SEQUENCE OF TSAsyModeTtyEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing how to set the tty mode on interface." ::= { terminalServer 2 } tsAsyModeTtyEntry OBJECT-TYPE SYNTAX TSAsyModeTtyEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Management information about how to set the tty mode on interface." INDEX { tsAsyModeTtyID, tsAsyModeTtyVtyID} ::= { tsAsyModeTtyTable 1 } TSAsyModeTtyEntry ::= SEQUENCE { tsAsyModeTtyID INTEGER, tsAsyModeTtyVtyID INTEGER, tsAsyModeTtyIFIndex INTEGER, tsAsyModeTtyAppID INTEGER, tsAsyModeTtyDisconnect INTEGER, tsAsyModeTtyVtyState INTEGER, tsAsyModeTtyFlowCtrlState INTEGER, tsAsyModeTtyStatus EntryStatus } tsAsyModeTtyID OBJECT-TYPE SYNTAX INTEGER(0..128) ACCESS read-only STATUS mandatory DESCRIPTION "Set the tty ID." ::= { tsAsyModeTtyEntry 1 } tsAsyModeTtyVtyID OBJECT-TYPE SYNTAX INTEGER(0..3) ACCESS read-only STATUS mandatory DESCRIPTION "Set the vty ID." ::= { tsAsyModeTtyEntry 2 } tsAsyModeTtyIFIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Select the current interface." ::= { tsAsyModeTtyEntry 3 } tsAsyModeTtyAppID OBJECT-TYPE SYNTAX INTEGER(-1..515) ACCESS read-write STATUS mandatory DESCRIPTION "Set the application ID,-1 indicate no app." ::= { tsAsyModeTtyEntry 4 } tsAsyModeTtyDisconnect OBJECT-TYPE SYNTAX INTEGER{ disconnect(1) } ACCESS write-only STATUS mandatory DESCRIPTION "Disconnect current VTY's tcp." ::= { tsAsyModeTtyEntry 5 } tsAsyModeTtyVtyState OBJECT-TYPE SYNTAX INTEGER{ down(1), up(2), waitaaa(3), ok(4), menu(5) } ACCESS read-only STATUS mandatory DESCRIPTION "Display the state of the unix." ::= { tsAsyModeTtyEntry 6 } tsAsyModeTtyFlowCtrlState OBJECT-TYPE SYNTAX INTEGER{ start(1), stop(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Display whether set flow control mode." ::= { tsAsyModeTtyEntry 7 } tsAsyModeTtyStatus OBJECT-TYPE SYNTAX EntryStatus ACCESS read-write STATUS mandatory DESCRIPTION "Set the tty state in the interface.It can create a new row and delete a row.But when creat a new row,the application must be set.If you modify a row under the status of row, you change the status from valid to undercreation.when you have changed them,you change the status to valid.And if you will create a row,the values of tsAsyModeTtyIFIndex,tsAsyModeTtyAppID must be not null." ::= { tsAsyModeTtyEntry 8 } tsTtyTable OBJECT-TYPE SYNTAX SEQUENCE OF TSTtyEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing how to set something about the tty.If the tty no set,you can't set the values" ::= { terminalServer 3 } tsTtyEntry OBJECT-TYPE SYNTAX TSTtyEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Management information about how to set something about the tty." INDEX { tsTtyID} ::= { tsTtyTable 1 } TSTtyEntry ::= SEQUENCE { tsTtyID INTEGER, tsTtyBufferSize INTEGER, tsTtyAutoLink INTEGER, tsTtyCloseLink INTEGER, tsTtyConnPrint INTEGER, tsTtyDelay INTEGER, tsTtyLogoPrint INTEGER, tsTtyMenuKey1 INTEGER, tsTtyMenuKey2 INTEGER, tsTtyMenuKey3 INTEGER, tsTtyReadBlock INTEGER, tsTtyRedrawkey1 INTEGER, tsTtyRedrawkey2 INTEGER, tsTtyRedrawkey3 INTEGER, tsTtyResetKey1 INTEGER, tsTtyResetKey2 INTEGER, tsTtyResetKey3 INTEGER, tsTtyTcpNoDelay INTEGER, tsTtyTcpRecvBufferSize INTEGER, tsTtyTcpSendBufferSize INTEGER, tsTtyTestKey1 INTEGER, tsTtyTestKey2 INTEGER, tsTtyTestKey3 INTEGER, tsTtyBufferRate INTEGER, tsTtyRecvBytes INTEGER, tsTtySendBytes INTEGER, tsTtyLastRecvTime DisplayString, tsTtyLastSendTime DisplayString, tsTtyCurrentVtyID INTEGER, tsTtyCurrentVtyRecv INTEGER, tsTtyCurrentVtySend INTEGER, tsTtyCurrentAppID INTEGER, tsTtyCurrentAppRecv INTEGER, tsTtyCurrentAppSend INTEGER, tsTtyClearStatistic INTEGER, tsDebugTtyAll INTEGER, tsDebugTtyBrief INTEGER, tsDebugTtySock INTEGER, tsDebugTtyTimeStamp INTEGER, tsDebugTtyTty INTEGER } tsTtyID OBJECT-TYPE SYNTAX INTEGER(0..128) ACCESS read-only STATUS mandatory DESCRIPTION "Set the tty ID." ::= { tsTtyEntry 1 } tsTtyBufferSize OBJECT-TYPE SYNTAX INTEGER(4096..204800) ACCESS read-write STATUS mandatory DESCRIPTION "Set the buffer size(byte)." DEFVAL {4096} ::= { tsTtyEntry 2 } tsTtyAutoLink OBJECT-TYPE SYNTAX INTEGER(0|5..3600) ACCESS read-write STATUS mandatory DESCRIPTION "Set auto link interval(second)." DEFVAL {0} ::= { tsTtyEntry 3 } tsTtyCloseLink OBJECT-TYPE SYNTAX INTEGER(0|5..3600) ACCESS read-write STATUS mandatory DESCRIPTION "Set auto close link interval(second)." DEFVAL {0} ::= { tsTtyEntry 4 } tsTtyConnPrint OBJECT-TYPE SYNTAX INTEGER{ english(1), chinese(2), none(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Print connection information." DEFVAL {chinese} ::= { tsTtyEntry 5 } tsTtyDelay OBJECT-TYPE SYNTAX INTEGER(0..1200) ACCESS read-write STATUS mandatory DESCRIPTION "Print connection information(second)." DEFVAL {0} ::= { tsTtyEntry 6 } tsTtyLogoPrint OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Display the logo of terminal server." DEFVAL {disable} ::= { tsTtyEntry 7 } tsTtyMenuKey1 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set the hotkey to start-up terminal server." DEFVAL {0} ::= { tsTtyEntry 8 } tsTtyMenuKey2 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set the hotkey to start-up terminal server." DEFVAL {0} ::= { tsTtyEntry 9 } tsTtyMenuKey3 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set the hotkey to start-up terminal server." DEFVAL {0} ::= { tsTtyEntry 10 } tsTtyReadBlock OBJECT-TYPE SYNTAX INTEGER{ set(1), noSet(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set read TTY data block." DEFVAL {noSet} ::= { tsTtyEntry 11 } tsTtyRedrawkey1 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set redraw screen hot-key." DEFVAL {0} ::= { tsTtyEntry 12 } tsTtyRedrawkey2 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set redraw screen hot-key." DEFVAL {0} ::= { tsTtyEntry 13 } tsTtyRedrawkey3 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set redraw screen hot-key." DEFVAL {0} ::= { tsTtyEntry 14 } tsTtyResetKey1 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set reset hot-key." DEFVAL {0} ::= { tsTtyEntry 15 } tsTtyResetKey2 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set reset hot-key." DEFVAL {0} ::= { tsTtyEntry 16 } tsTtyResetKey3 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set reset hot-key." DEFVAL {0} ::= { tsTtyEntry 17 } tsTtyTcpNoDelay OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set tcp NODELAY option." DEFVAL {enable} ::= { tsTtyEntry 18 } tsTtyTcpRecvBufferSize OBJECT-TYPE SYNTAX INTEGER(512..16384) ACCESS read-write STATUS mandatory DESCRIPTION "Set tcp recv buffer size(byte)." DEFVAL {2048} ::= { tsTtyEntry 19 } tsTtyTcpSendBufferSize OBJECT-TYPE SYNTAX INTEGER(512..16384) ACCESS read-write STATUS mandatory DESCRIPTION "Set tcp send buffer size(byte)." DEFVAL {1024} ::= { tsTtyEntry 20 } tsTtyTestKey1 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set test hot-key." DEFVAL {0} ::= { tsTtyEntry 21 } tsTtyTestKey2 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set test hot-key." DEFVAL {0} ::= { tsTtyEntry 22 } tsTtyTestKey3 OBJECT-TYPE SYNTAX INTEGER(0..127) ACCESS read-write STATUS mandatory DESCRIPTION "Set test hot-key." DEFVAL {0} ::= { tsTtyEntry 23 } tsTtyBufferRate OBJECT-TYPE SYNTAX INTEGER(0..100) ACCESS read-only STATUS mandatory DESCRIPTION "Display the rate of flow control(%)." ::= { tsTtyEntry 24 } tsTtyRecvBytes OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the byte number of the tty that has received." ::= { tsTtyEntry 25 } tsTtySendBytes OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the byte number of the tty that has sent." ::= { tsTtyEntry 26 } tsTtyLastRecvTime OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Display the last time of the tty that received." ::= { tsTtyEntry 27 } tsTtyLastSendTime OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Display the last time of the tty that sent." ::= { tsTtyEntry 28 } tsTtyCurrentVtyID OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the ID of the current vty." ::= { tsTtyEntry 29 } tsTtyCurrentVtyRecv OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the byte number of the vty that received." ::= { tsTtyEntry 30 } tsTtyCurrentVtySend OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the byte number of the vty that sent." ::= { tsTtyEntry 31 } tsTtyCurrentAppID OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the ID of the current vty." ::= { tsTtyEntry 32 } tsTtyCurrentAppRecv OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the byte number of the app that received." ::= { tsTtyEntry 33 } tsTtyCurrentAppSend OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the byte number of the app that sent." ::= { tsTtyEntry 34 } tsTtyClearStatistic OBJECT-TYPE SYNTAX INTEGER{ clear(1) } ACCESS write-only STATUS mandatory DESCRIPTION "Clear TTY's statistic information." ::= { tsTtyEntry 35 } tsDebugTtyAll OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Open/close specify tty's all debug information." DEFVAL {disable} ::= { tsTtyEntry 36 } tsDebugTtyBrief OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Open/close tty brief debug information." DEFVAL {disable} ::= { tsTtyEntry 37 } tsDebugTtySock OBJECT-TYPE SYNTAX INTEGER{ all(1), recv(2), send(3), none(4) } ACCESS read-write STATUS mandatory DESCRIPTION "socket data debug information." DEFVAL {none} ::= { tsTtyEntry 38 } tsDebugTtyTimeStamp OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "dataflow timestamp debug information." DEFVAL {disable} ::= { tsTtyEntry 39 } tsDebugTtyTty OBJECT-TYPE SYNTAX INTEGER{ all(1), recv(2), send(3), none(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Open/close the debug tty switch of the tty." DEFVAL {none} ::= { tsTtyEntry 40 } tsTtyManageTable OBJECT-TYPE SYNTAX SEQUENCE OF TSTtyManageEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table containing the information about the channel." ::= { terminalServer 4 } tsTtyManageEntry OBJECT-TYPE SYNTAX TSTtyManageEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Management information about how to bind tcp/ip." INDEX { tsTtyManageUnixIndex } ::= { tsTtyManageTable 1 } TSTtyManageEntry ::= SEQUENCE { tsTtyManageUnixIndex INTEGER, tsTtyManageUnixSockid INTEGER, tsTtyManageLocalIP IpAddress, tsTtyManageItemNum INTEGER } tsTtyManageUnixIndex OBJECT-TYPE SYNTAX INTEGER(0..511) ACCESS read-only STATUS mandatory DESCRIPTION "An index for unix." ::= { tsTtyManageEntry 1 } tsTtyManageUnixSockid OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the sock ID that the channel is using." ::= { tsTtyManageEntry 2 } tsTtyManageLocalIP OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Display the Local IP address." ::= { tsTtyManageEntry 3 } tsTtyManageItemNum OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Display the number of unix item." ::= { tsTtyManageEntry 4 } tsEnable OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Decide whether to have the function of terminal server." DEFVAL {disable} ::= { terminalServer 5 } tsEnableTrap OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Decide whether to send terminal server trap." DEFVAL {disable} ::= { terminalServer 6 } tsClearTtyAll OBJECT-TYPE SYNTAX INTEGER{ clear(1) } ACCESS write-only STATUS mandatory DESCRIPTION "Clear the information of the app and tty." ::= { terminalServer 7 } tsLoginTty OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS obsolete DESCRIPTION "Enable HWTTY EXEC Authentication." DEFVAL {disable} ::= { terminalServer 8 } tsDebugTtyGroup OBJECT IDENTIFIER ::= { terminalServer 9 } tsDebugTtyError OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "tty exception error information." DEFVAL {disable} ::= { tsDebugTtyGroup 1 } tsDebugTtyManage OBJECT-TYPE SYNTAX INTEGER{ enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "manage channel debug information." DEFVAL {disable} ::= { tsDebugTtyGroup 2 } tsTrap OBJECT IDENTIFIER ::= { terminalServer 10 } tsAppStatusTrap NOTIFICATION-TYPE OBJECTS { tsAppID,tsAppTtyServerState } STATUS current DESCRIPTION "send a value when the state of application change." ::= { tsTrap 1 } tsTtyStatusTrap NOTIFICATION-TYPE OBJECTS { tsAsyModeTtyID,tsAsyModeTtyVtyID,tsAsyModeTtyVtyState } STATUS current DESCRIPTION "send a value when the state of tty change." ::= { tsTrap 2 } tsExceptionTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "send a Exception when the terminal server has exception." ::= { tsTrap 3 } tsClearSuccessTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Clear statistic successfully." ::= { tsTrap 4 } tsDisconnectSuccessTrap NOTIFICATION-TYPE STATUS current DESCRIPTION "Disconnect vty successfully." ::= { tsTrap 5 } END