--=========================================================== -- Copyright (c) 2010-2013 Hewlett-Packard Development Company, L.P. -- Description: This MIB is excerpted from the draft-ietf-hubmib-efm-epon-mib-02 directly --- only changed the object name,added the hpnicf as prefix. -- Reference: -- Version: V1.0 -- History: -- V1.0 created by liyue. -- Define MODULE-IDENTITY for hpnicfDot3EfmeponMIB --================================================================= HPN-ICF-DOT3-EFM-EPON-MIB DEFINITIONS ::= BEGIN IMPORTS hpnicfEpon FROM HPN-ICF-OID-MIB MODULE-IDENTITY, mib-2, OBJECT-TYPE, Counter32, Integer32, OBJECT-IDENTITY FROM SNMPv2-SMI TruthValue, MacAddress FROM SNMPv2-TC ifIndex FROM IF-MIB MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; hpnicfDot3EfmeponMIB MODULE-IDENTITY LAST-UPDATED "200409210000Z" -- September 21, 2004 ORGANIZATION "" CONTACT-INFO "" DESCRIPTION "The objects in this MIB module are used to manage the Ethernet in the First Mile (EFM) Multi Point Control Protocol (MPCP) Interfaces as defined in IEEE Draft P802.3ah/D3.0 clause 64,65. The following reference is used throughout this MIB module: [802.3ah] refers to: IEEE Draft P802.3ah/D3.3: 'Draft amendment to - Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks', 22 April 2004. Of particular interest are Clause 64(MPCP) 65(P2MP RS) and 60 (PON PMDs). Clause 30, 'Management', and Clause 45, 'Management Data Input/Output (MDIO) Interface'. Copyright (C) The Internet Society (2004). This version of this MIB module is part of XXXX see the RFC itself for full legal notices." -- Editor's Note: Replace XXXX with the actual RFC number -- assigned by RFC Editor and remove this note REVISION "200409210000Z" -- September 21, 2004 DESCRIPTION "Initial version, published as RFC XXXX." ::= { hpnicfEpon 2 } -- Editor's Note: Replace XXX with a real OID once it is -- assigned by IANA and remove this note. -- Editor-s note: MPCP MIB modules definitions ([802.3ah] --- clause 30.3.5) -- Editor-s note: Description in attributes with References should be -- minimized in later versions hpnicfDot3MpcpMIB OBJECT IDENTIFIER ::= { hpnicfDot3EfmeponMIB 1 } hpnicfDot3MpcpObjects OBJECT IDENTIFIER ::= { hpnicfDot3MpcpMIB 1 } hpnicfDot3MpcpConformance OBJECT IDENTIFIER ::= { hpnicfDot3MpcpMIB 2 } hpnicfDot3MpcpTable OBJECT-TYPE SYNTAX SEQUENCE OF HpnicfDot3MpcpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for dot3 Multi-Point Control Protocol (MPCP) MIB modules." ::= { hpnicfDot3MpcpObjects 1 } hpnicfDot3MpcpEntry OBJECT-TYPE SYNTAX HpnicfDot3MpcpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the dot3 MPCP MIB modules table." INDEX { ifIndex } ::= { hpnicfDot3MpcpTable 1 } HpnicfDot3MpcpEntry ::= SEQUENCE { hpnicfDot3MpcpID Integer32, hpnicfDot3MpcpOperStatus TruthValue, hpnicfDot3MpcpMode INTEGER, hpnicfDot3MpcpLinkID Integer32, hpnicfDot3MpcpRemoteMACAddress MacAddress, hpnicfDot3MpcpRegistrationState INTEGER, hpnicfDot3MpcpTransmitElapsed Integer32, hpnicfDot3MpcpReceiveElapsed Integer32, hpnicfDot3MpcpRoundTripTime Integer32, hpnicfDot3MpcpMaximumPendingGrants Integer32, hpnicfDot3MpcpAdminState TruthValue, hpnicfDot3MpcpOnTime Integer32, hpnicfDot3MpcpOffTime Integer32, hpnicfDot3MpcpSyncTime Integer32 } hpnicfDot3MpcpID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is assigned so as to uniquely identify the Multi-Point MAC Control (MPCP) entity, as defined in [802.3ah] clause 64, among the subordinate managed objects of the containing object. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.1.1." ::= { hpnicfDot3MpcpEntry 1 } hpnicfDot3MpcpOperStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable can be used to define the operational state of the Multi-Point MAC Control sublayer as defined in [802.3ah] clause 64. Selecting admin for an interface with Multi-Point MAC Control sublayer. When the attribute is True the the interface will act as if Multi-point control protocol is enabled. When the attribute is False the interface will act as if it does not have the Multi-point control protocol. The operational state can be changed using the hpnicfDot3MpcpAdminState attribute. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.1.2." ::= { hpnicfDot3MpcpEntry 2 } hpnicfDot3MpcpMode OBJECT-TYPE SYNTAX INTEGER { olt(1), onu(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This variable can be used to identify the operational state of the Multi-Point MAC Control sublayer as defined in [802.3ah] clause 64. Selecting olt(1) for an OLT (server) mode and onu(2) for an ONU (client) mode. Writing can be done during only during initialization, when hpnicfDot3MpcpOperStatus indicates Flase. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.1.3." DEFVAL { 1 } ::= { hpnicfDot3MpcpEntry 3 } hpnicfDot3MpcpLinkID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that identifies the Logical Link identity (LLID) associated with the MAC port as specified in [802.3ah] clause 65.1.3.2.2. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.1.4." ::= { hpnicfDot3MpcpEntry 4 } hpnicfDot3MpcpRemoteMACAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that identifies the source_address parameter of the last MPCPDUs passed to the MAC Control. This value is updated on reception of a valid frame with (1) a destination Field equal to the reserved multicast address for MAC Control specified in [802.3ah] Annex 31A, (2) lengthOrType field value equal to the reserved Type for MAC Control as specified in [802.3ah] Annex 31A. (3) an MPCP subtype value equal to the subtype reserved for MPCP as specified in [802.3ah] Annex 31A. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.1.5." ::= { hpnicfDot3MpcpEntry 5 } hpnicfDot3MpcpRegistrationState OBJECT-TYPE SYNTAX INTEGER { unregistered(1), registering(2), registered(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that identifies the operational state of the Multi-Point MAC Control sublayer as defined in [802.3ah] clause 64. When this attribute has the enumeration unregistered(1) the interface may be used for registering a link partner. When this attribute has the enumeration registering(2) the interface is in the process of registering a link-partner. When this attribute has the enumeration registered(3) the interface has an established link-partner. This attribute is relevant for an OLT and an ONU. For the OLT it provides an indication per LLID." REFERENCE "[802.3ah], 30.3.5.1.6." ::= { hpnicfDot3MpcpEntry 6 } hpnicfDot3MpcpTransmitElapsed OBJECT-TYPE SYNTAX Integer32 UNITS "TQ (16nsec)" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the interval from last MPCP frame transmission in increments of Time Quanta (TQ) 16ns. The value returned shall be (interval from last MPCP frame transmission in ns)/16. If this value exceeds (2^32-1) the value (2^32-1) shall be returned. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.1.19." ::= { hpnicfDot3MpcpEntry 7 } hpnicfDot3MpcpReceiveElapsed OBJECT-TYPE SYNTAX Integer32 UNITS "TQ (16nsec)" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the interval from last MPCP frame reception in increments of Time Quanta (TQ) 16ns. The value returned shall be (interval from last MPCP last MPCP frame reception in ns)/16. If this value exceeds (2^32-1) the value (2^32-1) shall be returned. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.1.20." ::= { hpnicfDot3MpcpEntry 8 } hpnicfDot3MpcpRoundTripTime OBJECT-TYPE SYNTAX Integer32 UNITS "TQ (16nsec)" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the MPCP round trip time in increments of Time Quanta (TQ) 16ns. The value returned shall be (round trip time in ns)/16. If this value exceeds (2^16-1) the value (2^16-1) shall be returned. This attribute is relevant for an OLT and an ONU. For the OLT there is a value per LLID" REFERENCE "[802.3ah], 30.3.5.1.21." ::= { hpnicfDot3MpcpEntry 9 } hpnicfDot3MpcpMaximumPendingGrants OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that indicates the maximum number of grants an ONU can store. The maximum number of grants an ONU can store has a range of 0 to 255. This attribute is relevant for an OLT and an ONU. For the OLT there is a value per LLID" REFERENCE "[802.3ah], 30.3.5.1.24." ::= { hpnicfDot3MpcpEntry 10 } hpnicfDot3MpcpAdminState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This variable can be used to define the operational state of the Multi-Point MAC Control sublayer as defined in [802.3ah] clause 64. Selecting admin for an interface with Multi-Point MAC Control sublayer. When selecting the value as True the interface Multi-Point control protocol is enabled. When selecting the value as False the interface acts as if the Multi-point Control protocol does not exist. Reading reflects the state of the attribute and the operation of the Multi-point control protocol mode of the interface. Writing can be done all the time. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.2.1." DEFVAL { false } ::= { hpnicfDot3MpcpEntry 11 } hpnicfDot3MpcpOnTime OBJECT-TYPE SYNTAX Integer32 UNITS "TQ (16nsec)" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the -on time- for a grant burst in increments of Time Quanta (TQ) 16ns as defined in [802.3ah] 60,64. The value returned shall be (on time ns)/16. If this value exceeds (2^32-1) the value (2^32-1) shall be returned. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 64.3.5.1." ::= { hpnicfDot3MpcpEntry 12 } hpnicfDot3MpcpOffTime OBJECT-TYPE SYNTAX Integer32 UNITS "TQ (16nsec)" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the -off time- for a grant burst in increments of Time Quanta (TQ) 16ns as defined in [802.3ah] 60,64. The value returned shall be (off time ns)/16. If this value exceeds (2^32-1) the value (2^32-1) shall be returned. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 64.3.5.1." ::= { hpnicfDot3MpcpEntry 13 } hpnicfDot3MpcpSyncTime OBJECT-TYPE SYNTAX Integer32 UNITS "TQ (16nsec)" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that reports the -sync lock time- for an OLT receiver in increments of Time Quanta (TQ) 16ns as defined in [802.3ah] 60,64,65. The value returned shall be (sync lock time ns)/16. If this value exceeds (2^32-1) the value (2^32-1) shall be returned. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 64.3.3.2." ::= { hpnicfDot3MpcpEntry 14 } hpnicfDot3MpcpStatTable OBJECT-TYPE SYNTAX SEQUENCE OF HpnicfDot3MpcpStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the list of statistics counters of [802.3ah] clause 64 MPCP interface." ::= { hpnicfDot3MpcpObjects 2 } hpnicfDot3MpcpStatEntry OBJECT-TYPE SYNTAX HpnicfDot3MpcpStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table entries for table of statistics counters of [802.3ah] clause 64 MPCP interface." INDEX { ifIndex } ::= { hpnicfDot3MpcpStatTable 1 } HpnicfDot3MpcpStatEntry ::= SEQUENCE { hpnicfDot3MpcpMACCtrlFramesTransmitted Counter32, hpnicfDot3MpcpMACCtrlFramesReceived Counter32, hpnicfDot3MpcpDiscoveryWindowsSent Counter32, hpnicfDot3MpcpDiscoveryTimeout Counter32, hpnicfDot3MpcpTxRegRequest Counter32, hpnicfDot3MpcpRxRegRequest Counter32, hpnicfDot3MpcpTxRegAck Counter32, hpnicfDot3MpcpRxRegAck Counter32, hpnicfDot3MpcpTxReport Counter32, hpnicfDot3MpcpRxReport Counter32, hpnicfDot3MpcpTxGate Counter32, hpnicfDot3MpcpRxGate Counter32, hpnicfDot3MpcpTxRegister Counter32, hpnicfDot3MpcpRxRegister Counter32, hpnicfDot3MpcpRxNotSupportedMPCP Counter32 } hpnicfDot3MpcpMACCtrlFramesTransmitted OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MPCP frames passed to the MAC sublayer for transmission. This counter is incremented when a MA_CONTROL.request service primitive is generated within the MAC control sublayer with an opcode indicating a MPCP frame. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.1.7." ::= { hpnicfDot3MpcpStatEntry 1 } hpnicfDot3MpcpMACCtrlFramesReceived OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of MPCP frames passed by the MAC sublayer to the MAC Control sublayer. This counter is incremented when a ReceiveFrame function call returns a valid frame with: (1) a lengthOrType field value equal to the reserved Type for 802.3_MAC_Control as specified in 31.4.1.3, and (2) an opcode indicating a MPCP frame. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.1.8." ::= { hpnicfDot3MpcpStatEntry 2 } hpnicfDot3MpcpDiscoveryWindowsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of discovery windows generated. The counter is incremented by one for each generated discovery window. This attribute is relevant for an OLT and an ONU. At the ONU value should be zero." REFERENCE "[802.3ah], 30.3.5.1.22." ::= { hpnicfDot3MpcpStatEntry 3 } hpnicfDot3MpcpDiscoveryTimeout OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a discovery timeout occurs. Increment the counter by one for each discovery processing state-machine reset resulting from timeout waiting for message arrival. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.5.1.23." ::= { hpnicfDot3MpcpStatEntry 4 } hpnicfDot3MpcpTxRegRequest OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REGISTER_REQ MPCP frames transmission occurs. Increment the counter by one for each REGISTER_REQ MPCP frame transmitted as defined in [802.3ah] clause 64. This counter is mandatory for an ONU. This attribute is relevant for an OLT and an ONU. At the OLT value should be zero." REFERENCE "[802.3ah], 30.3.5.1.12." ::= { hpnicfDot3MpcpStatEntry 5 } hpnicfDot3MpcpRxRegRequest OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REGISTER_REQ MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each REGISTER_REQ MPCP frame received for each LLID as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT. At the ONU value should be zero." REFERENCE "[802.3ah], 30.3.5.1.17." ::= { hpnicfDot3MpcpStatEntry 6 } hpnicfDot3MpcpTxRegAck OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REGISTER_ACK MPCP frames transmission occurs. Increment the counter by one for each REGISTER_ACK MPCP frame transmitted as defined in [802.3ah] clause 64. This counter is mandatory for an ONU. This attribute is relevant for an OLT and an ONU. At the OLT the value should be zero." REFERENCE "[802.3ah], 30.3.5.1.10." ::= { hpnicfDot3MpcpStatEntry 7 } hpnicfDot3MpcpRxRegAck OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REGISTER_ACK MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each REGISTER_ACK MPCP frame received for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT. At the ONU the value should be zero." REFERENCE "[802.3ah], 30.3.5.1.15." ::= { hpnicfDot3MpcpStatEntry 8 } hpnicfDot3MpcpTxReport OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REPORT MPCP frames transmission occurs. Increment the counter by one for each REPORT MPCP frame transmitted as defined in [802.3ah] clause 64. This counter is mandatory for an ONU. This attribute is relevant for an OLT and an ONU. At the OLT value should be zero." REFERENCE "[802.3ah], 30.3.5.1.13." ::= { hpnicfDot3MpcpStatEntry 9 } hpnicfDot3MpcpRxReport OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REPORT MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each REPORT MPCP frame received for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT. At the ONU value should be zero." REFERENCE "[802.3ah], 30.3.5.1.18." ::= { hpnicfDot3MpcpStatEntry 10 } hpnicfDot3MpcpTxGate OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a GATE MPCP frames transmission occurs. A set of counters, one for each LLID, at the OLT. Increment the counter by one for each GATE MPCP frame transmitted, for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an OLT. This attribute is relevant for an OLT and an ONU. At the ONU the value should be zero." REFERENCE "[802.3ah], 30.3.5.1.9." ::= { hpnicfDot3MpcpStatEntry 11 } hpnicfDot3MpcpRxGate OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a GATE MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID ,at the OLT. Increment the counter by one for each GATE MPCP frame received, for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT. At the OLT the value should be zero." REFERENCE "[802.3ah], 30.3.5.1.14." ::= { hpnicfDot3MpcpStatEntry 12 } hpnicfDot3MpcpTxRegister OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REGISTER MPCP frames transmission occurs. A set of counters, one for each LLID, at the OLT. Increment the counter by one for each REGISTER MPCP frame transmitted, for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an OLT. This attribute is relevant for an OLT and an ONU. At the ONU the value should be zero." REFERENCE "[802.3ah], 30.3.5.1.11." ::= { hpnicfDot3MpcpStatEntry 13 } hpnicfDot3MpcpRxRegister OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a REGISTER MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each REGISTER MPCP frame received, for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT. at the OLT the value should be zero." REFERENCE "[802.3ah], 30.3.5.1.16." ::= { hpnicfDot3MpcpStatEntry 14 } hpnicfDot3MpcpRxNotSupportedMPCP OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the number of times a non-supported MPCP frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each non-supported MPCP frame received, for each LLID, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and for an OLT." ::= { hpnicfDot3MpcpStatEntry 15 } -- Conformance Statements -- Conformance Groups hpnicfDot3MpcpGroups OBJECT IDENTIFIER ::= { hpnicfDot3MpcpConformance 1 } hpnicfDot3MpcpGroupBase OBJECT-GROUP OBJECTS { hpnicfDot3MpcpID, hpnicfDot3MpcpOperStatus, hpnicfDot3MpcpMode, hpnicfDot3MpcpLinkID, hpnicfDot3MpcpRemoteMACAddress, hpnicfDot3MpcpRegistrationState, hpnicfDot3MpcpMaximumPendingGrants, hpnicfDot3MpcpAdminState } STATUS current DESCRIPTION "A collection of objects of dot3 Mpcp Basic entity state definition." ::= { hpnicfDot3MpcpGroups 1 } hpnicfDot3MpcpGroupParam OBJECT-GROUP OBJECTS { hpnicfDot3MpcpTransmitElapsed, hpnicfDot3MpcpReceiveElapsed, hpnicfDot3MpcpRoundTripTime, hpnicfDot3MpcpOnTime, hpnicfDot3MpcpOffTime, hpnicfDot3MpcpSyncTime } STATUS current DESCRIPTION "A collection of objects of dot3 Mpcp for P2MP parameters." ::= { hpnicfDot3MpcpGroups 2 } hpnicfDot3MpcpGroupStat OBJECT-GROUP OBJECTS { hpnicfDot3MpcpMACCtrlFramesTransmitted, hpnicfDot3MpcpMACCtrlFramesReceived, hpnicfDot3MpcpDiscoveryWindowsSent, hpnicfDot3MpcpDiscoveryTimeout , hpnicfDot3MpcpTxRegRequest, hpnicfDot3MpcpRxRegRequest, hpnicfDot3MpcpTxRegAck, hpnicfDot3MpcpRxRegAck, hpnicfDot3MpcpTxReport, hpnicfDot3MpcpRxReport, hpnicfDot3MpcpTxGate, hpnicfDot3MpcpRxGate, hpnicfDot3MpcpTxRegister, hpnicfDot3MpcpRxRegister, hpnicfDot3MpcpRxNotSupportedMPCP } STATUS current DESCRIPTION "A collection of objects of dot3 Mpcp Statistics" ::= { hpnicfDot3MpcpGroups 3 } -- Compliance hpnicfDot3MpcpCompliances OBJECT IDENTIFIER ::= { hpnicfDot3MpcpConformance 2 } hpnicfDot3MpcpCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for Multi-point control protocol interfaces." MODULE -- this module MANDATORY-GROUPS { hpnicfDot3MpcpGroupBase } GROUP hpnicfDot3MpcpGroupParam DESCRIPTION "This group is mandatory for all MPCP supporting interfaces for configuration of the Multipoint Parameters." GROUP hpnicfDot3MpcpGroupStat DESCRIPTION "This group is mandatory for all MPCP supporting interfaces for Statistics collection." ::= { hpnicfDot3MpcpCompliances 1 } -- Editor-s note: OMPEmulation managed object definitions hpnicfDot3OmpEmulationMIB OBJECT IDENTIFIER ::= { hpnicfDot3EfmeponMIB 2 } hpnicfDot3OmpEmulationObjects OBJECT IDENTIFIER ::= { hpnicfDot3OmpEmulationMIB 1 } hpnicfDot3OmpeConformance OBJECT IDENTIFIER ::= { hpnicfDot3OmpEmulationMIB 2 } hpnicfDot3OmpEmulationTable OBJECT-TYPE SYNTAX SEQUENCE OF HpnicfDot3OmpEmulationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for dot3 OmpEmulation MIB modules." ::= { hpnicfDot3OmpEmulationObjects 1 } hpnicfDot3OmpEmulationEntry OBJECT-TYPE SYNTAX HpnicfDot3OmpEmulationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the dot3 OmpEmulation MIB modules table." INDEX { ifIndex } ::= { hpnicfDot3OmpEmulationTable 1 } HpnicfDot3OmpEmulationEntry ::= SEQUENCE { hpnicfDot3OmpEmulationID Integer32, hpnicfDot3OmpEmulationType INTEGER } hpnicfDot3OmpEmulationID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of hpnicfDot3OmpEmulationID is assigned so as to uniquely identify a OMPEmulation entity among the subordinate managed objects of the containing object. The value is mandated for an ONU." REFERENCE "[802.3ah], 30.3.7.1.1." ::= { hpnicfDot3OmpEmulationEntry 1 } hpnicfDot3OmpEmulationType OBJECT-TYPE SYNTAX INTEGER { unknown(1), olt(2), onu(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that indicates that mode of operation of the Reconciliation Sublayer for Point to Point Emulation (see [802.3ah] clause 65.1). unknown(1) value is assigned in initializing, true state or type not yet known. olt(2) value is assigned when Sublayer operating in OLT mode. onu(3) value is assigned when Sublayer operating in ONU mode." REFERENCE "[802.3ah], 30.3.7.1.2." ::= { hpnicfDot3OmpEmulationEntry 2 } hpnicfDot3OmpEmulationStatTable OBJECT-TYPE SYNTAX SEQUENCE OF HpnicfDot3OmpEmulationStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the list of statistics counters of [802.3ah] clause 65 OMP interface." ::= { hpnicfDot3OmpEmulationObjects 2 } hpnicfDot3OmpEmulationStatEntry OBJECT-TYPE SYNTAX HpnicfDot3OmpEmulationStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table entries for Table of statistics counters of [802.3ah] clause 65 OMP interface." INDEX { ifIndex } ::= { hpnicfDot3OmpEmulationStatTable 1 } HpnicfDot3OmpEmulationStatEntry ::= SEQUENCE { hpnicfDot3OmpEmulationSLDErrors Counter32, hpnicfDot3OmpEmulationCRC8Errors Counter32, hpnicfDot3OmpEmulationBadLLID Counter32, hpnicfDot3OmpEmulationGoodLLID Counter32, hpnicfDot3OmpEmulationOnuPonCastLLID Counter32, hpnicfDot3OmpEmulationOltPonCastLLID Counter32, hpnicfDot3OmpEmulationBroadcastLLIDNotOnuID Counter32, hpnicfDot3OmpEmulationOnuLLIDNotBroadcast Counter32, hpnicfDot3OmpEmulationBroadcastLLIDPlusOnuId Counter32, hpnicfDot3OmpEmulationNotBroadcastLLIDNotOnuId Counter32 } hpnicfDot3OmpEmulationSLDErrors OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that do not contain a valid SLD field as defined in [802.3ah] clause 65.1.3.3.1. This attribute is mandatory for an OLT and optional for an ONU." REFERENCE "[802.3ah], 30.3.7.1.3." ::= { hpnicfDot3OmpEmulationStatEntry 1 } hpnicfDot3OmpEmulationCRC8Errors OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field, as defined in [802.3ah] clause 65.1.3.3.1, but do not pass the CRC-8 check as defined in [802.3ah] clause 65.1.3.3.3. This attribute is mandatory for an OLT and for an ONU." REFERENCE "[802.3ah], 30.3.7.1.4." ::= { hpnicfDot3OmpEmulationStatEntry 2 } hpnicfDot3OmpEmulationBadLLID OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3, but are discarded due to the LLID check as defined in [802.3ah] clause 65.1.3.3.2. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.7.1.8." ::= { hpnicfDot3OmpEmulationStatEntry 3 } hpnicfDot3OmpEmulationGoodLLID OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3. This attribute is relevant for an OLT and an ONU." REFERENCE "[802.3ah], 30.3.7.1.5." ::= { hpnicfDot3OmpEmulationStatEntry 4 } hpnicfDot3OmpEmulationOnuPonCastLLID OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in an ONU, as defined in [802.3ah] 65.1.3.3.1, passes the CRC-8 check, as defined in [802.3ah] 65.1.3.3.3, and the frame meets the rule for acceptance defined in [802.3ah] 65.1.3.3.2." REFERENCE "[802.3ah], 30.3.7.1.6." ::= { hpnicfDot3OmpEmulationStatEntry 5 } hpnicfDot3OmpEmulationOltPonCastLLID OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in an OLT, as defined in [802.3ah] 65.1.3.3.1, passes the CRC-8 check, as defined in [802.3ah] 65.1.3.3.3, and the frame meets the rule for acceptance defined in [802.3ah] 65.1.3.3.2." REFERENCE "[802.3ah], 30.3.7.1.7." ::= { hpnicfDot3OmpEmulationStatEntry 6 } hpnicfDot3OmpEmulationBroadcastLLIDNotOnuID OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in a OLT, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3, and contain broadcast LLID as defined in [802.3ah] clause 65. This attribute is mandatory for an OLT and for an ONU." ::= { hpnicfDot3OmpEmulationStatEntry 7 } hpnicfDot3OmpEmulationOnuLLIDNotBroadcast OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in a OLT, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3, and contain the ONU's LLID as defined in [802.3ah] clause 65. This attribute is mandatory for an ONU and mandatory for an OLT (a counter per LLID)." ::= { hpnicfDot3OmpEmulationStatEntry 8 } hpnicfDot3OmpEmulationBroadcastLLIDPlusOnuId OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in a OLT, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3, and contain the broadcast LLID plus ONU's LLID (frame reflected) as defined in [802.3ah] clause 65. This attribute is mandatory for an ONU and mandatory for an OLT (a counter per LLID)." ::= { hpnicfDot3OmpEmulationStatEntry 9 } hpnicfDot3OmpEmulationNotBroadcastLLIDNotOnuId OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of frames received that contain a valid SLD field in a OLT, as defined in [802.3ah] clause 65.1.3.3.1, and pass the CRC-8 check, as defined in [802.3ah] clause 65.1.3.3.3, and does not contain the ONU's LLID as defined in [802.3ah] clause 65. This attribute is mandatory for an ONU" ::= { hpnicfDot3OmpEmulationStatEntry 10 } -- Conformance Statements -- Conformance Groups hpnicfDot3OmpeGroups OBJECT IDENTIFIER ::= { hpnicfDot3OmpeConformance 1 } hpnicfDot3OmpeGroupID OBJECT-GROUP OBJECTS { hpnicfDot3OmpEmulationID, hpnicfDot3OmpEmulationType } STATUS current DESCRIPTION "A collection of objects of dot3 OMP emulation ID entity state definition." ::= { hpnicfDot3OmpeGroups 1 } hpnicfDot3OmpeGroupStat OBJECT-GROUP OBJECTS { hpnicfDot3OmpEmulationSLDErrors, hpnicfDot3OmpEmulationCRC8Errors, hpnicfDot3OmpEmulationBadLLID, hpnicfDot3OmpEmulationGoodLLID, hpnicfDot3OmpEmulationOnuPonCastLLID, hpnicfDot3OmpEmulationOltPonCastLLID, hpnicfDot3OmpEmulationBroadcastLLIDNotOnuID, hpnicfDot3OmpEmulationOnuLLIDNotBroadcast, hpnicfDot3OmpEmulationBroadcastLLIDPlusOnuId, hpnicfDot3OmpEmulationNotBroadcastLLIDNotOnuId } STATUS current DESCRIPTION "A collection of objects of dot3 OMP emulation Statistics" ::= { hpnicfDot3OmpeGroups 2 } -- Compliance hpnicfDot3OmpeCompliances OBJECT IDENTIFIER ::= { hpnicfDot3OmpeConformance 2 } hpnicfDot3OmpeCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for OMPEmulation interfaces." MODULE -- this module MANDATORY-GROUPS { hpnicfDot3OmpeGroupID } GROUP hpnicfDot3OmpeGroupStat DESCRIPTION "This group is mandatory for all OMPemulation supporting interfaces for Statistics collection." ::= { hpnicfDot3OmpeCompliances 1 } -- Editor-s note: MAU managed object definitions (30.5.1) hpnicfDot3EponMauMIB OBJECT IDENTIFIER ::= { hpnicfDot3EfmeponMIB 3 } hpnicfDot3EponMauObjects OBJECT IDENTIFIER ::= { hpnicfDot3EponMauMIB 1 } hpnicfDot3EponMauConformance OBJECT IDENTIFIER ::= { hpnicfDot3EponMauMIB 2 } hpnicfDot3EponMauTable OBJECT-TYPE SYNTAX SEQUENCE OF HpnicfDot3EponMauEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for dot3 MAU EPON MIB modules." ::= { hpnicfDot3EponMauObjects 1 } hpnicfDot3EponMauEntry OBJECT-TYPE SYNTAX HpnicfDot3EponMauEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the dot3 MAU EPON MIB modules table." INDEX { ifIndex } ::= { hpnicfDot3EponMauTable 1 } HpnicfDot3EponMauEntry ::= SEQUENCE { hpnicfDot3EponMauPCSCodingViolation Counter32, hpnicfDot3EponMauFecAbility INTEGER, hpnicfDot3EponMauFecMode INTEGER, hpnicfDot3EponMauFECCorrectedBlocks Counter32, hpnicfDot3EponMauFECUncorrectableBlocks Counter32, hpnicfDot3EponMauBufferHeadCodingViolation Counter32 } hpnicfDot3EponMauPCSCodingViolation OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "For 100 Mb/ s operation it is a count of the number of times an invalid code-group is received, other than the /H/ code-group. For 1000 Mb/ s operation it is a count of the number of times an invalid codegroup is received, other than the /V/ code-group." REFERENCE "[802.3ah], 30.5.1.1.12." ::= { hpnicfDot3EponMauEntry 1 } hpnicfDot3EponMauFecAbility OBJECT-TYPE SYNTAX INTEGER { unknown (1), nonsupported (2), supported (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value that indicates the support of operation of the 1000BASE-PX PHY optional FEC Sublayer for Forward error correction see [802.3ah] clause 65.2). unknown(1) value is assigned in initializing, for non FEC support state or type not yet known. nonsupported(2) value is assigned when Sublayer is not support. supported(3) value is assigned when Sublayer is supported." REFERENCE "[802.3ah], 30.5.1.1.13." ::= { hpnicfDot3EponMauEntry 2 } hpnicfDot3EponMauFecMode OBJECT-TYPE SYNTAX INTEGER { unknown (1), disabled (2), enabled (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "A read-write value that indicates the mode of operation of the 1000BASE-PX PHY optional FEC Sublayer for Forward error correction see [802.3ah] clause 65.2). A GET operation returns the current mode of operation the PHY. A SET operation changes the mode of operation of the PHY to the indicated value. unknown(1) value is assigned in initializing, for non FEC support state or type not yet known. disabled(2) value is assigned when Sublayer operating in disabled mode. enabled(3) value is assigned when Sublayer operating in FEC mode. writing can be done all the time." REFERENCE "[802.3ah], 30.5.1.1.14." DEFVAL { 1 } ::= { hpnicfDot3EponMauEntry 3 } hpnicfDot3EponMauFECCorrectedBlocks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "For 10PASS-TS, 2BASE-TL and 1000BASE-PX PHYs, a count of corrected FEC blocks. This counter will not increment for other PHY Types. Increment the counter by one for each received block that is corrected by the FEC function in the PHY." REFERENCE "[802.3ah], 30.5.1.1.15." ::= { hpnicfDot3EponMauEntry 4 } hpnicfDot3EponMauFECUncorrectableBlocks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "For 10PASS-TS, 2BASE-TL and 1000BASE-PX PHYs, a count of uncorrectable FEC blocks. This counter will not increment for other PHY Types. Increment the counter by one for each FEC block that is determined to be uncorrectable by the FEC function in the PHY." REFERENCE "[802.3ah], 30.5.1.1.16." ::= { hpnicfDot3EponMauEntry 5 } hpnicfDot3EponMauBufferHeadCodingViolation OBJECT-TYPE SYNTAX Counter32 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "For 1000 Mbps operation it is a counts of the number of invalid code-group received directly from the link." ::= { hpnicfDot3EponMauEntry 6 } -- Defining EPON MAU types -- Editor's Note: This section should be added to 802.3 MAU MIB -- module RFC. Preference would be that the MAU MIB module -- structure would change so that it is re-written as an -- IANA-maintained module. hpnicfDot3EponMauType OBJECT IDENTIFIER ::= { hpnicfDot3EponMauMIB 3 } hpnicfEponMauType1000BasePXOLT OBJECT-IDENTITY STATUS current DESCRIPTION "Multipoint MAC Control (per 802.3 section 64,65) OLT (master), unknown PMD" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { hpnicfDot3EponMauType 1 } hpnicfEponMauType1000BasePXONU OBJECT-IDENTITY STATUS current DESCRIPTION "Multipoint MAC Control (per 802.3 section 64,65),ONU (slave), unknown PMD" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { hpnicfDot3EponMauType 2 } hpnicfEponMauType1000BasePX10DOLT OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 10K link, downlink (per 802.3 section 60), OLT side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { hpnicfDot3EponMauType 3 } hpnicfEponMauType1000BasePX10DONU OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 10K link, downlink (per 802.3 section 60), ONU side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { hpnicfDot3EponMauType 4 } hpnicfEponMauType1000BasePX10UOLT OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 10K link, uplink (per 802.3 section 60), OLT side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { hpnicfDot3EponMauType 5 } hpnicfEponMauType1000BasePX10UONU OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 10K link, uplink (per 802.3 section 60), ONU side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { hpnicfDot3EponMauType 6 } hpnicfEponMauType1000BasePX20DOLT OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 20K link, downlink (per 802.3 section 60), OLT side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { hpnicfDot3EponMauType 7 } hpnicfEponMauType1000BasePX20DONU OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 20K link, downlink (per 802.3 section 60), ONU side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { hpnicfDot3EponMauType 8 } hpnicfEponMauType1000BasePX20UOLT OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 20K link, uplink (per 802.3 section 60), OLT side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { hpnicfDot3EponMauType 9 } hpnicfEponMauType1000BasePX20UONU OBJECT-IDENTITY STATUS current DESCRIPTION "EPON over 20K link, uplink (per 802.3 section 60), ONU side" REFERENCE "[802.3ah], 30.5.1.1.2." ::= { hpnicfDot3EponMauType 10 } -- Conformance Statements -- Conformance Groups hpnicfDot3EponMauGroups OBJECT IDENTIFIER ::= { hpnicfDot3EponMauConformance 1 } hpnicfDot3EponMauGroupAll OBJECT-GROUP OBJECTS { hpnicfDot3EponMauPCSCodingViolation } STATUS current DESCRIPTION "A collection of objects of dot3 MAU definition." ::= { hpnicfDot3EponMauGroups 1 } hpnicfDot3EponMauGroupFEC OBJECT-GROUP OBJECTS { hpnicfDot3EponMauFecAbility, hpnicfDot3EponMauFecMode, hpnicfDot3EponMauFECCorrectedBlocks, hpnicfDot3EponMauFECUncorrectableBlocks, hpnicfDot3EponMauBufferHeadCodingViolation } STATUS current DESCRIPTION "A collection of objects of FEC group definition." ::= { hpnicfDot3EponMauGroups 2 } -- Compliance hpnicfDot3EponMauCompliances OBJECT IDENTIFIER ::= { hpnicfDot3EponMauConformance 2 } hpnicfDot3EponMauCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for MAU EPON interfaces." MODULE -- this module MANDATORY-GROUPS { hpnicfDot3EponMauGroupAll } GROUP hpnicfDot3EponMauGroupFEC DESCRIPTION "This group is mandatory for all EPON MAU devices Supporting FEC functionality as for Definitions and BER Statistics collection." ::= { hpnicfDot3EponMauCompliances 1 } END